In this paper, Fe-Cr-C-N-Al-Y wear-resistant surfacing alloy was prepared by open arc surfacing with self-shielded flux-cored wire. The wear properties of the surfacing alloy were analyzed by MLS-23 rubber wheel wet sand wear tester. The phase composition and microstructure of the surfacing alloy were analyzed by XRD, SEM, EBSD and TEM, and the strengthening mechanism and wear mechanism of the alloy were discussed. The results show that the microstructure of Fe-Cr-C-N-Al-Y surfacing alloy is composed of M + γ-Fe + M7C3 + AlN. When the content of nano-Y2O3 is 0.456wt. %, the formability of the surfacing alloy is the best and the wetting angle is the smallest, which is 50.8°, AlN and M7C3 precipitate the most, and the microstructure grain is the smallest. At this time, the hardness value of the surfacing alloy is up to 62.3 HRC, which is 11.8 % higher than that of the unmodified surfacing alloy. The minimum wear weight loss is 0.125 g, and the wear resistance is increased by 41.86 %. The wear mechanism of surfacing alloy is mainly plastic deformation mechanism, and the material removal process is micro cutting and furrow wear.

Fe-(9, 19, 28, 37)wt.% Cr alloys were corroded at 700 and 800 ^oC for 70 h under 1 atm of N₂, 1 atm of N₂/3.2%H₂O-mixed gas, and 1 atm of N₂/3.1%H₂O/2.42%H₂S-mixed gas. The corrosion rate of Fe-9Cr alloy increased with the addition of H₂O, and furthermore with the addition of H₂S in N₂ gas. Fe-9Cr alloy was always nonprotective. In contrast, Fe-(19, 28, 37) wt.%Cr alloys were protective in N₂ and N₂/H₂O-mixed gas because of formation of the Cr₂O₃ layer. They were, however, nonprotective in N₂/H₂O/H₂S-mixed gas because sulfidation dominated to form the outer FeS layer and the inner Cr₂S₃ layer containing some FeCr₂S₄.

In diabetic foot injury prevention, no studies relate physical activity with the inflammatory response of the plantar tissues, evaluated by thermography and pressure distribution. These measurements are easy to be implemented in diabetic foot follow-up. The objective of this study was to analyze whether the plantar skin response, evaluated with thermography, after physical activity in healthy or diabetic patients, is a foot ulcer prognostic tool and to asses if there is a correlation between exercise intensity, plantar pressure and plantar thermographic response. A systematic review was carried out following Preferred Reporting Items for Systematic Reviews and Meta-Analyses (PRISMA) format in the PubMed, Scopus and Web of Science databases, with no year limit during the second quarter of 2024. A total of 14 studies have been included in this review. The use of infrared thermography for early inflammatory tissue detection, plantar pressures and the monitoring of controlled physical activity, make possible to monitor changes that allow the identification of patients at risk of developing foot ulcers.

Compared to other 2D materials, MBenes are at an early stage in both experimental and theoretical approaches. However, the wide range of possible 2D structures leads to novel and challenging properties and their consequent applications. From all the possible stoichiometries, we have performed a theoretical study of orthorhombic and hexagonal M2B2 MBenes in the framework of the Density Functional Theory. We have found that both symmetries of Cr2B2, Fe2B2, and Zr2B2 show a metallic behavior and could be grown under certain conditions, as they are demonstrated to be dynamically stable. Moreover, the values of the magnetic moment, in specific ferromagnetic cases exceeding 2.5 μB/M2B2, make them suitable as robust 2D magnets. All our findings represent an important step in the understanding of MBenes and open several windows to future research in fields like energy conversion and storage, sensing, catalysis, biochemistry, or nanotechnology, among others.

For the last two decades, an increasing demand for low-cost adsorbents for drinking water treatment has been challenged in the rural areas of developing countries that have problems with arsenic (As) contamination. In this work, spent bleaching earth (SBE), a residual material that is formed during the process of refining vegetable oil, has been utilized to prepare the new magnetic adsorbent Fe-SBE/C by modifying its surface area through calcination and co-precipitation with iron. The experimental results demonstrate that Fe-SBE/C exhibits a substantial adsorption capacity towards both arsenite (As(III)) and arsenate (As(V)). Optimal pH conditions were found to be pH 10 for As(III) and pH 3 for As(V), resulting in adsorption percentages of 76.7% and 94.1%, respectively. Other experimental parameters such as calcination conditions, adsorbent dosage, iron-loading ratio, and the presence of co-existing ions were thoroughly investigated. The kinetic study revealed that the adsorption processes follow the Elovich and intraparticle diffusion models, suggesting a combined adsorption mechanism of boundary layer control and chemisorption. Furthermore, the isotherm followed the Langmuir model with a maximum adsorption capacity of 202.61 μg g-1 for As(III) and 187.61 μg g-1 for As(V). Through thermodynamic analysis and reinforcement by activation energy data, this research validates that the observed adsorption process is indicative through chemisorption. The regeneration study revealed the potential for multiple cycles of arsenic removal, highlighting the practical applicability of Fe-SBE/C in environmental contexts. In conclusion, the findings of this study underscore the efficacy of Fe-SBE/C in arsenic removal and present it as a promising and environmentally friendly solution for mitigating arsenic pollution.

There are several well-described molecular mechanisms that influence cell growth and are relat-ed to the development of cancer. Chemokines constitute a fundamental element which are not only involved in local growth but also affect angiogenesis, tumor spread and metastatic disease. Among them, the C-X-C motif chemokine ligand 12 (CXCL12) and its specific receptor the chemo-kine C-X-C motif receptor 4 (CXCR4) have been widely studied. The overexpression in cell mem-branes of CXCR4 has been shown to be associated with the development of different kinds of his-tological malignancies, such as adenocarcinomas, epidermoid carcinomas, mesenchymal tumors or neuroendocrine neoplasms (NENs). The molecular synapsis between CXCL12 and CXCR4 leads to the interaction of G proteins and activation of different intracellular signaling pathways in both gastroenteropancreatic (GEP) and bronchopulmonary (BP) NENs conferring greater ca-pacity for locoregional aggressiveness, epithelial-mesenchymal transition (EMT) and the ap-pearance of metastases. Therefore, it has been hypothesized how to design tools that target this receptor. The aim of this review is to focus on current knowledge of the relationship between CXCR4 and NENs, with a special emphasis on diagnostic and therapeutic molecular targets.

In this work, we investigated the effects of heat treatment on the microstructure, hydrogen storage characteristics and corrosion rate of a Ti₃₄V₄₀Cr₂₄Fe₂ alloy. The arc melted alloy was divided into three samples, two of which were separately quartz-sealed under vacuum and heated to 1000 °C for 1 h; one of these samples was quenched and the other furnace cooled to ambient temperature. The crystal structures of the samples were studied via X-ray diffractometry and scanning electron microscopy. Absorption/desorption characteristics were investigated using a Sievert apparatus. Potentiostat corrosion tests on the alloys were performed using an AutoLab^® corrosion test apparatus and electrochemical cell. All samples exhibited a mixture of body-center-cubic (BCC) and Laves phase structures. The corrosion rate, maximum absorption, and useful capacities increased after both heat treatments. The annealed sample had the highest absorption and reversible capacity. The plateau pressure of the as-cast alloy increased after quenching. The corrosion rate increased from 0.0004 mm/y in as-cast sample to 0.0009 mm/y after annealing and 0.0017 mm/y after quenching, due to a decrease in the Cr-content of the C14 phase.

A two-layer Fe-Cr-Al-Zr surface alloy was synthesized on a zirconium substrate by magnetron sputtering and subsequent low-energy high-current electron-beam (LEHCEB) processing. Thicknesses of the top Fe69Cr20Al11 (at.%) relatively large-grained (~1 µm) and transition Fe-Zr Cr-Al amorphous layers were about 0.7 and 0.6 µm, respectively. In turn, the amorphous layer consisted of two Fe64–54Zr8–22Cr21–17Al8–7 and Fe40–16Zr42–78Cr12–4Al6–2 (at.%) sublayers, differing in both zirconium and iron concentrations in wide ranges, which were separated by another nanocrystalline interlayer. The Fe-Cr-Al-Zr surface alloy serve as a diffusion barrier, preventing interaction of the zirconium substrate with oxygen from an environment. It was thermally stable up to ≈1173 K.

Dental caries is a public health problem worldwide according to WHO data. Among treatments in pediatric dentistry, prefabricated metal crowns (PMCs) have been one of the most successful options since they were introduced in cases of considerable tooth destruction. Our objective was to detect the presence and concentration of iron (Fe), chromium (Cr), and nickel (Ni) in saliva of patients who require rehabilitation with PMCs, before and after their placement. A quasi-experimental study was performed in 32 patients who attended dental care in a pediatric dentistry clinic at a public university and who required rehabilitation with PMCs. Parametric tests (ANOVA and Pearson correlation) were performed, and a p ≤ 0.05 was considered statistically significant. Statistically significant differences were found when comparing the Ni release before, 1 week, and 1 month after placing the crowns. Similarly, we observed a positive correlation between the number of crowns and Ni release. No tests were performed for Fe and Cr because the amounts of these metals were less than 0.1 ppb, which was not detectable by inductively coupled plasma optical emission spectrometry (ICP-OES). The levels of Fe, Cr, and Ni released were below toxic health levels. Studies are required to evaluate whether this release has negative effects at cellular levels.

Chronic kidney disease (CKD) affects approximately 12% of the global population posing a significant health threat. Inflammation plays a crucial role in the uremic phenotype of CKD contributing to elevated cardiovascular and overall mortality in affected individuals. This study aimed to explore novel metabolic pathways in non-dialysis dependent stage 5 CKD patients using semitargeted metabolomics. In a prospective observational design involving 50 patients, blood samples collected before the initial hemodialysis session underwent liquid chromatography and high resolution mass spectrometer analysis. Univariate (Mann-Whitney test) and multivariate (logistic regression with LASSO regularization) methods identified metabolomic variables associated with inflammation. Notably, adenosine-5’-phosphosulfate (APS), dimethylglycine, pyruvate, lactate, and 2-ketobutyric acid exhibited significant differences in the presence of inflammation. Cholic acid, homogentisic acid, and 2-phenylpropionic acid displayed opposing patterns. Multivariate analysis indicated increased inflammation risk with certain metabolites (N-Butyrylglycine, dimethylglycine, 2-Oxoisopentanoic acid, and pyruvate), while others (homogentisic acid, 2-Phenylpropionic acid, and 2-Methylglutaric acid) suggested decreased probability. These findings unveil potential inflammation-associated biomarkers related to defective mitochondrial fatty acid beta oxidation and branched-chain amino acid breakdown in CKD, shedding light on cellular energy production and offering insights for further clinical validation.

Bamboo is the building material of the past and future. It offers numerous properties that make it versatile for various applications, including construction. Its impressive strength-to-weight ratio enables it to bear substantial loads and stresses, while its good elasticity allows efficient energy absorption. However, its mechanical properties can vary based on factors such as species, age, locations, methods, and treatment. Treating bamboo is essential to enhance its properties and durability. The literature provides various natural and chemical treatments which enhanced some of the properties but also reported a drawbacks on higher temperature, content and duration. This paper reviewed 57 articles from Scopus database, specifically focusing on article-document type publications from the years 2003 to 2023. Additional references were also incorporated to address concerns in properties, treatment and standards to provide systematic understanding. MATLAB was utilized for data text analytics. With extensive assessment on the articles, the following gaps and concerns were observed and recommends for further study and assessment such as for bamboo properties, the development of centralized guidelines and procedures for the preparation and processing; exploration of alternative materials to reinforce bamboo without compromising its ductility; development of joint connections, and testing of mechanical properties considering seismic, wind and vibration. For treatment methods, the standardization of procedures using natural, chemical or combination. Lastly, for bamboo codes and standards, assessment of existing codes and standards for testing the mechanical properties of bamboo highlighting the potential limitations and areas, uniformity, differences with all existing similar standards. By filling these gaps, it can support the reliability and robustness of bamboo as a sustainable material, fostering its promotion and adoption in construction industry.

3.9 million individuals rely on kidney replacement therapy worldwide. They experience height-ened susceptibility to cardiovascular diseases and mortality, alongside an increased risk of in-fections and malignancies, with inflammation being key to explaining this intensified risk. This study utilized semi-targeted metabolomics to explore novel metabolic pathways related to in-flammation in this populations. We collected pre and post-session blood samples of patients who had already undergone one year of chronic hemodialysis. And used liquid chromatography and high resolution mass spectrometry to perform a metabolomic analysis. Afterwards, we employed both univariate (Mann-Whitney test) and multivariate (logistic regression with LASSO regulari-zation) to identify metabolites associated with inflammation. In the univariate analysis, in-dole-3-acetaldehyde, 2-ketobutyric acid, and urocanic acid showed statistically significant de-creases in median concentrations in the presence of inflammation. In the multivariate analysis, metabolites positively associated with inflammation include allantoin, taurodeoxycholic acid, norepinephrine, pyroglutamic acid, and L-hydroorotic acid. Conversely, metabolites showing negative associations with inflammation include benzoic acid, indole-3-acetaldehyde, methio-nine, citrulline, alphaketoglutarate, n-acetyl-ornithine and 3-4-dihydroxibenzeneacetic acid. Non inflamed patients exhibit preserved autophagy and reduced mitochondrial dysfunction. Under-standing inflammation in this group hinges on the metabolism of arginine and the urea cycle. Additionally, the microbiota, particularly uricase-producing bacteria and those metabolizing tryptophan, play critical roles.

The last decade has seen a significant growth in low-cost air quality monitoring systems (LCAQMS) adoption, mostly driven by the spatial density limitations of traditional regulatory grade networks which restrict their effectiveness in several settings. The EU's regulatory framework advise for deploying one air quality monitoring unit per roughly 170,000 people or 15 square kilometers which is insufficient for capturing high spatio-temporal variance in complex urban scenarios. Often these settings are characterized by distributed emissions in small roads subjected to intense cars traffic, house heating driven emissions and frequently subjected to canyon effects. The Air Heritage project in Portici, funded by the EU's Urban Innovative Actions (UIA) program, addressed these challenges by integrating low-cost sensors with traditional monitoring systems and engaging the community in pervasive measurement strategies. The project highlights the importance of individualized sensor calibration and frequent recalibrations to maintain accuracy. It also showcases the benefits of citizen science approaches, IoT infrastructures, AI components, and geostatistical sensor fusion algorithms for mobile and opportunistic air quality measurements. This paper reports on the lessons learned and experiences from the Air Heritage project, aiming to guide future implementations in similar contexts. By sharing these insights along with the gathered datalake, we aim to inform stakeholders, including researchers, public authorities, and citizens, about effective strategies for deploying and utilizing LCAQMS to enhance air quality monitoring and public awareness.

Seawater contamination is a global challenge due to its hazardous effects on marine organisms and human health. Twenty-three surface seawater samples were collected from Al Lith intertidal area along the Saudi Red Sea coast to evaluate the ecological risks and document the potential sources of Cr, Cd, Fe, Zn, and Pb. Contamination factor (CF), contamination degree (Cd), water quality index (WQI), and heavy metal pollution index (HPI), as well as multivariate tools were applied. The averages of HMs (μg/L) had the following order: Zn (6.616) > Pb (0.284) > Cd and Cr (0.268) > Fe (0.197). Results of CF showed moderate contamination of seawater with Cd and low contamination for Cr, Fe, Zn, and Pb. However, 26.09% of the samples showed considerable contamination for Cd. Average Cd values revealed low contamination for HMs, while 17.39% of the samples showed moderate contamination. HPI average values indicated medium pollution for Al Lith seawater, meanwhile 13 samples reported high pollution. The higher HPI values were reported in samples characterized by higher concentration of HMs, particularly Cd and Zn. Correlation matrix and principal component analysis suggested anthropogenic sources for Pb and Zn, mostly from industrial and agricultural effluents, landfilling and domestic wastewaters, apart from their natural sources.

The development of platinum group metal-free (PGM-free) electrocatalysts derived from cheap and environmentally friendly biomasses for oxygen reduction reaction (ORR) is a topic of relevant interest, particularly from the point of view of sustainability. Fe-nitrogen-doped carbon materials (Fe-N-C) have attracted particular interest as alternative to Pt-based materials, due to the high activity and selectivity of Fe-Nx active sites, the high availability and good tolerance to poisoning. Recently, many studies focused on developing synthetic strategies, which could transform N-containing biomasses into N-doped carbons. In this paper chitosan was employed as a suitable N-containing biomass for preparing Fe-N-C catalyst in virtue of its high N content (7.1%) and unique chemical structure. Moreover, the major application of chitosan is based on its ability to strongly coordinate metal ions, a precondition for the formation of Fe-Nx active sites. The synthesis of Fe-N-C consists in a double step thermochemical conversion of a dried chitosan hydrogel. In acidic aqueous solution, the preparation of physical cross-linked hydrogel allows to obtain sophisticated organization, which assure an optimal mesoporosity before and after the pyrolysis. After the second thermal treatment at 900 °C, a highly graphitized material was obtained, which has been fully characterized in term of textural, morphological and chemical properties. RRDE technique was used for understanding the activity and the selectivity of the material versus the ORR in 0.5 M H2SO4 electrolyte. Special attention was put in the determination of the active site density according to nitrite electrochemical reduction measurements. It was clearly established that the catalytic activity expressed as half wave potential linearly scales with the number of Fe-Nx sites. It was also established that the addition of the iron precursor after the first pyrolysis step leads to an increased activity because of both an increased number of active sites and of a hierarchical structure, which improves the access to active sites. At the same time, the increased graphitization degree, and a reduced density of pyrrolic nitrogen groups are helpful to increase the selectivity toward the 4e- ORR pathway.

This study investigates the effect of Re addition on the microstructure evolution and oxidation resistance of Co-Cr-Ta-Ti-C alloys. The alloys tested in this study consist of a Co-rich matrix with mixed HCP and FCC phases, together with TaTiC2 and Ti-based carbides. The addition of Re promotes the precipitation and growth of a CoCr-rich σ phase. Differential thermal analysis (DTA) showed that the melting temperatures did not change drastically up to 10 at% Re addition, whereas 15 at% Re addition significantly increased the melting temperature of the alloys. Oxidation tests in air at 1200°C showed that excessive Re content could lead to deterioration in oxidation resistance, mainly due to the accelerated formation of volatile Re oxides.

This research aims to elucidate the organizational patterns of interregional economic interdependence to enhance our comprehension of the national economy's structure at a regional scale. Employing a multilayer network model, this study represents economic interdependence among Indonesian regions, utilizing the InterRegional Input-Output (IRIO) table. Through the application of various metrics, such as degree and strength distribution, assortativity coefficient, and global and local rich club coefficient, to the multilayer IRIO network, we uncover the organizational patterns of economic exchanges between provinces and economic sectors within Indonesia. Our findings demonstrate that a multilayer network approach reveals the heterogeneous and complex structure of the national economy at the regional level. By analyzing the assortativity pattern and global rich-club coefficient, we illustrate that the IRIO network exhibits a hierarchical organization, where significant provincial-sector nodes are interconnected and form dense rich clubs, extending from a few structural cores to peripheral regions. Additionally, we identify distinct connectivity patterns of non-rich nodes based on their incoming and outgoing relations. The insights gained from this study have implications for the macro-control of regional development.

The traditional societies evolved locally with the realms of time in their calendars while modern Gregorian based on the solar movement and some others use lunar or the combination with solar. Unveiling some information from the old manuscripts to gain the realm of traditional Batak people since the ancient times in settlements surrounding the tropical Lake Toba, North Sumatera, Indonesia, revival of cosmos is delivered. Uniquely the ancient Batak count days in a month by observing lunar phase and the period of year is by looking the observable Constellation of Orion & Scorpius within the new phase of the moon. Thus there are years with 12 months and some leap years with 13 months, and we propose to categorize the calendar to be lunar-star, relative to other widely analyzed calendars. In the realization of the use of the cosmogram, we cross the period of the leap year to the examination of contemporary data on agriculture event, i.e.: crop failure, as well as some profiles on weather. The revival of the Batak Calendar opens further interesting conjectures based on the rich cultural and astronomical knowledge embedded in tradition with deep connection between celestial observations and timekeeping.

The influence of pore size on the toughness of Fe-Mo-Cu-C sintered and carburized components was investigated. The charpy impact value of the component made from Fe-0.4%Mo diffusion-alloyed steel powder mixed with 2%Cu powder and 0.3% graphite powder significantly increased with a decrease in pore size. The highest impact value of 17 J/cm2 was obtained at the average pore size of 12 µm. This value was 25% higher than that of the sintered and carburized component made from conventional Fe- 4%Ni-1.5%Cu-0.5%Mo alloyed steel powder called 4Ni even though the component was made from a Ni-free alloyed steel powder. The mechanism of the improvement of the impact value by pore size refinement and the influence of microstructural difference between the components made from Fe- 0.4%Mo diffusion-alloyed steel powder and 4Ni on toughness is discussed based on optical microstructural observation and crystal orientation analysis data.

The efficiency and performance of Proton Exchange Membrane Fuel Cells (PEMFCs) are primarily influenced by ORR electrocatalysts. In recent years, atomically dispersed met-al-nitrogen-carbon (M-N-C) catalysts have gained significant attention due to their high active center density, high atomic utilization, and high activity. These catalysts are now considered the preferred alternative to traditional noble metal electrocatalysts. The unique properties of M-N-C catalysts are anticipated to enhance the energy conversion efficiency and lower the manufac-turing cost of the entire system, thereby facilitating the commercialization and widespread ap-plication of fuel cell technology. This article initially delves into the origin of performance and degradation mechanisms of Fe-N-C catalysts from both experimental and theoretical perspectives. Building on this foundation, the focus shifts to strategies aimed at enhancing the activity and durability of atomically dispersed Fe-N-C catalysts. These strategies encompass the use of bi-metallic atoms, atomic clusters, heteroatoms (B, S, and P), and morphology regulation to optimize catalytic active sites. The article concludes by detailing the current challenges and future pro-spects of atomically dispersed Fe-N-C catalysts.

Iron and chromium based alloys have found wide application in various fields of science and technology. Primary carrier based on Fe-Cr-Al alloy is used in block catalysts for high-temperature hydrocarbon conversion, in production of block metal catalysts for neutralization of toxic gases released during operation of internal combustion engines, as well as those present in smoke emissions from enterprises. Influence of thermal action on Fe-Cr-Al alloy foil and stability of secondary carrier on its surface was studied. Elemental composition of the surface layer of X15U5 alloy foil does not remain constant during heating and depends on the thermal treatment mode. Some of the elements come to surface and elemental composition of surface layer can differ significantly from that observed in the bulk of foil sample. This implies the possibility of changing the adhesive and adsorption properties of the foil surface, as well as the need to take this fact into account when supporting a secondary carrier and active phase to the foil. Applied technique of phosphating and supporting a secondary carrier to the foil surface makes it possible to obtain a sufficiently stable coating. There is no shedding of the secondary carrier from foil surface during high-temperature treatment in air.

In this work the influence of the structure forming agent on the composition, morphology and oxygen reduction reaction (ORR) activity of Fe-N-C catalysts was investigated. As structure forming agent (SFA), dicyandiamide (DCDA) (nitrogen source) or oxalic acid (oxygen source) or mixtures thereof were used. For characterization, cyclic voltammetry and rotating disc electrode (RDE) experiments were performed in 0.1 M H2SO4. In addition to this, N2 sorption measurements and Raman spectroscopy were performed for the structural characterization. The role of metal, nitrogen and carbon sources within the synthesis of Fe-N-C catalysts has been pointed out before. Here, we show that the optimum in terms of ORR activity is achieved if both N- and O-containing SFAs are used in almost similar fractions. All catalysts display a redox couple, whereat its position depends on the fractions of SFAs. The SFA has also a strong impact on the morphology: Catalysts that were prepared with a larger fraction of N-containing SFA revealed a higher order in graphitization, indicated by bands in the 2nd order range of the Raman spectra. Nevertheless, the optimum in terms of ORR activity is obtained for the catalyst with highest D/G band ratio. Therefore, the results indicate that the presence of an additional oxygen-containing SFA is beneficial within the preparation.

Litsea martabanica root's antioxidant and AChE activity showed promise as a pesticide detoxification agent in our previous study. In addition to roots, its leaves can help mitigate pesticide exposure, although there is limited scientific evidence supporting their efficacy. However, the use of roots in many countries, such as Thailand, could contribute to environmental degradation, as highland communities traditionally cut down whole trees to obtain them. This study aims to evaluate the antioxidant activity and anti-pesticide potential of water extracts from L. martabanica leaves instead of its roots through in vitro and in vivo investigations. The findings showed that L. martabanica water extracts and fractions demonstrated varied antioxidant activity. The water extract, obtained using traditional extraction methods, was chosen for in vivo experiments. Rats received the extract followed by chlorpyrifos exposure for 16 days. Results indicated reduced acetylcholinesterase activity in chlorpyrifos-exposed rats, while treatment with leaf extract led to increased activity, suggesting its potential as a detoxifying agent. Histopathological examination revealed no liver cell necrosis and showed liver cell regeneration, indicating potential protection against free radical-induced liver damage without affecting rat liver weight or biochemical profiles. Utilizing L. martabanica leaves for healthcare purposes holds promise without negative environmental impact.

Fiscal control and monitoring of public management are issues of great importance and relevance, as they focus on preventing and mitigating corruption, thus benefiting governments in their management and performance, and thus citizens. Given the large amount of data involved in the management and functioning of a government, it is pertinent to apply data analysis methods to contribute to fiscal control. This paper aims to investigate data management for this purpose, starting with a bibliometric study to demonstrate the relevance and pertinence of the current study. It examines existing data collection techniques that may facilitate such control, data storage considering its nature and the possibilities that contribute to this end, and data processing through techniques that allow obtaining adequate information for further analysis and decision making. The necessary architecture and interoperability between systems is also discussed, as the existence of large amounts and types of data in governments makes it crucial to promote these practices for accurate and truthful analysis. Finally, data visualization is addressed since this topic is highly relevant as it allows for the identification of anomalies, where proper visualization promotes appropriate analysis and thus informed decision making. This work is useful for modern audit and fiscal control entities, since data capture, storage, processing, interoperability, and visualization are crucial elements that collectively enhance the ability to supervise public expenditure effectively, ensuring that public funds are managed with the highest standards of transparency, accountability, and efficiency.

This paper reviews the current knowledge of pepper anthracnose in the Philippines. We present research outputs on pepper anthracnose from the last three years. Then, we present evidence of the widespread occurrence of C. acutatum sensu lato in the Philippines. Finally, we highlight some research prospects that would contribute towards developing an integrated anthracnose management program.

The Ionian Sea is a crucial intersection for various water masses in the Mediterranean. Its hydrography and dynamics play a significant role in the seawater budgets and biogeochemistry of the neighboring sub-basins. Multiple theories have been formulated to gain a better understanding of the Ionian dynamics. These theories primarily attribute the variability of the near-surface Ionian circulation to internal processes. Here, we utilize horizontal currents and temperature-salinity profiles from the Copernicus reanalysis to examine the contribution of baroclinic modes to the variability of the basin horizontal circulation. Our findings demonstrate that, although the basin vertical structure is characterized by three layers, the primary patterns of the Ionian circulation can be attributed to the first baroclinic mode. This mode, along with the barotropic mode, accounts for over 85% of the overall variability in the Ionian circulation, suggesting that only one of the three interfaces separating the different water masses in the basin is dynamically active. We estimate the depth of this interface to be about 490 m. Additionally, our analysis shows that more than 90% of the kinetic energy over the water column is localized above this interface, indicating that the deep layer of the Ionian is dynamically nearly inert.

It has been argued that the historical nature of evolution makes it a highly path-dependent process. Under this view, the outcome of evolutionary dynamics could have resulted in organisms with different forms and functions. At the same time, there is ample evidence that convergence and constraints strongly limit the domain of the potential design principles that evolution can achieve. Are these limitations relevant in shaping the fabric of the possible? Here, we argue that fundamental constraints are associated with the logic of living matter. We illustrate this idea by considering the thermodynamic properties of living systems, the linear nature of molecular information, the cellular nature of the building blocks of life, multicellularity and development, the threshold nature of computations in cognitive systems, and the discrete nature of the architecture of ecosystems. In all these examples, we present available evidence and suggest potential avenues towards a well-defined theoretical formulation.

A conventionally cast CoNiFeMn0.5Cr1.5 alloy and two versions with 0.25C&3.7Ta or 0.25C&3.7Hf were tested in oxidation at 1000°C for 50h with thermogravimetric recording of the oxidation kinetic. In all cases the obtained mass gain curves are parabolic. Their parabolic constants are much lower than the Kp previously determined for the original alloys with an equimolar base (CoNiFeMnCr). However, the post–mortem exploitation of the oxidized samples revealed analogous oxidation features on surface and subsurface, with here too external oxide strata on surface with different Mn and Cr contents, and rather great Mn–depletion in addition to a moderate Cr–depletion, in subsurface. Globally, the oxidation behavior is significantly better than earlier observed for the equimolar version of these alloys.

RAMOSA1 (RA1) is a Cys2-His2-type (C2H2) zinc finger transcription factor that controls plant meristem fate and identity and has played an important role in maize domestication. Despite its importance, the origin of RA1 is unknown and the evolution in plants is partially understood. In this paper, we present a well resolved phylogeny based on 73 amino acid sequences from 48 embryophyte species. The recovered tree topology indicates that, during grass evolution, RA1 arose from two consecutive SUPERMAN duplications resulting in three distinct grass sequence lineages: RA1-like A, RA1-like B, and RA1; however, most of these copies have unknown functions. Our findings indicate that RA1 and RA1-like play roles in the nucleus despite lacking a traditional nuclear localization signal. Here we report that copies diversified their coding region and, with it, their protein structure, suggesting different patterns of DNA binding and protein-protein interaction. In addition, each of the retained copies diversified regulatory elements along their promoter regions, indicating differences in their upstream regulation. Taken together, we propose that the RA1 and RA1-like gene families in grasses may have undergone subfunctionalization and neofunctionalization enabled by gene duplication.

The incidence of infections due to carbapenemase-producing Enterobacteriaceae (CPE) is rising worldwide. We present the case of a 48-year-old female patient, diabetic, with previous episodes of urinary tract infections that was admitted due to pyelonephritis, later identified to be caused by KPC and ESBL-producing Klebsiella pneumoniae. Both the patient and her family had no strong epidemiological link with the healthcare system, and for this reason, this case stands out in regional literature since similar reports are scarce and therefore constitutes a reason for alert in health institutions. Further studies are needed in order to ascertain the real incidence of these infections in community settings in Latin America and the Caribbean.

The effects of partial replacement of Si by Al on the microstructure, tensile properties, and Charpy impact toughness were investigated using 0.2%C-Si/Al-Mn-Cr-B TRIP-aided martensitic steels. The impact toughness was related to the microstructural and mechanical properties. The partial re-placement decreased the volume fraction of retained austenite and increased the mechanical stabil-ity, accompanied by softening and an increase in the volume fraction of the primary martensite. Resultantly, the partial replacement decreased strength and ductility. The impact absorbed energy (value) at 25 C was slightly increased by the partial replacement. The increased impact absorbed energy was mainly caused by high crack/void propagation energy due to the softened primary martensite and a small contribution of the stabilized retained austenite. The 50% shear fracture ductile-to-brittle transition temperature was marginally raised by the partial replacement. The raised transition temperature was mainly associated with an increase in a unit crack path of qua-si-cleavage/cleavage fracture.

Copper-catalyzed and organocopper-involved reactions are of great significance in organic synthesis. To have a deep understanding of the reaction mechanisms, the structural characterizations of organocopper intermediates become indispensable. Meanwhile, the structure-function relationship of organocopper compounds would advance rational design and development of new Cu-based reactions and organocopper reagents. Compared to the mono-carbonic ligand, the C,N- and C,C-bidentate ligands better stabilize the unstable organocopper compounds. The bidentate ligands can chelate to the same copper atom via ?2-mode, forming a mono-cupra-cyclic compounds with at least one acute C-Cu-C angle. When the bidentate ligands bind to two copper atoms via ?1-mode at each coordinating site, the bimetallic macrocyclic compounds will form nearly linear C-Cu-C angles. The anionic coordinating sites of the bidentate ligand can also bridge two metals via ?2-mode, forming organocopper aggregates with Cu-Cu interactions and organocuprates with contact ion pair structures. The reaction chemistry of some selected organocopper compounds is highlighted, showing their unique structure-reactivity relationships.

A large core size and bending resistance are very important properties of mid-infrared energy transfer fibers, but large core sizes usually lead to a deterioration of bending properties. A negative-curvature nested node-free anti-resonant hollow-core fiber (AR-HCF) based on quartz is proposed. It was made by adding a nested layer to a previous AR-HCF design to provide an additional anti-resonance region while keeping the gap between adjacent tubes strictly correlated to the core diameter to produce a node-free structure. These features improve the fiber’s bending resistance while achieving a larger core diameter. The simulation results show that the radial air-glass anti-resonant layer is increased by the introduction of the nested anti-resonant tube, and the weak interference overlap between the fiber core and the cladding mode is reduced, so the fiber core’s limiting loss and the sensitivity to bending are effectively reduced. When the capillary wall thickness t of the fiber is 0.71 μm, the core diameter D is 70 μm, the ratio of the inner diameter of the cladding capillary to the core diameter d/D is 0.62, and the diameter of the nested tube is d0=29 μm, the fiber has a lower limiting loss at the wavelength of 2.79 μm, and the limiting loss is 3.28×10-4 dB/m. At the same time, the optimized structure also has good bending resistance. When the bending radius is 30 mm, the bending loss is only 4.72×10-2 dB/m. To our knowledge, this is the first research to achieve an anti-bending low-loss micro-structure hollow fiber with a bending radius of less than 30 mm in the 2.79 μm band. An anti-bending low-loss anti-resonant hollow-core fiber with this structure constitutes a reliable choice for the light guiding system of a 2.79 μm band erbium laser therapy instrument.

Background: Reliable HPV testing and genotyping are essential for quality assurance in HPV-based primary screening, disease management and for monitoring the impact of HPV vaccination. The clinical validation of HPV molecular diagnostic assays has significantly contributed to these objectives, however little emphasis has been placed in assuring sample quality. This study aims to assess the accuracy of sample cellularity assessment using C-C Motif Chemokine Receptor 5 (CCR5) gene target as a marker of sample adequacy in molecular diagnostics. Methods: Jurkat cell line samples were counted both using Thoma cell-counting chamber and Fluorescent-Activated Cell Sorting (FACS). Jurkat cell line samples at three different concentrations were subsequently evaluated using the OncoPredict HPV Quality Control (QC) real-time PCR assay, employing CCR5 for molecular cellularity quantification. Results: Cellularity values obtained were comparable across the 3 different methods for all dilutions of the cell line tested. Conclusions: The results obtained from this study show that CCR5 represents a promising molecular marker for the accurate quantification of sample cellularity, confirming its use as a reliable sample adequacy control, thus reducing the risk of “false negative” results.

Intelligence is a human construct to represent the ability to achieve goals. Given this wide berth, intelligence has been defined countless times, studied in a variety of ways and represented using numerous measures. Understanding intelligence ultimately requires theory and quantification, both of which have proved elusive. I develop a framework -- the Theory of Intelligences (TIS) -- that applies across all systems from physics, to biology, humans and AI. TIS likens intelligence to a calculus, differentiating, correlating and integrating information. Intelligence operates at many levels and scales and TIS distils these into a parsimonious macroscopic framework centered on solving, planning and their optimization to accomplish goals. Notably, intelligence can be expressed in informational units or in units relative to goal difficulty, the latter defined as goal complexity relative to system (individual or benchmarked) ability. I present general equations for intelligence and its components, and a simple expression for the evolution of intelligence traits. The measures developed here could be the basis for further refinements to gauge different facets of intelligence for any step-wise transformation of information. I argue that "proxies" such as environment, technology, society and collectives are essential to a general theory of intelligence and to possible evolutionary transitions in intelligence, particularly in humans. I conclude with testable predictions of TIS and offer several speculations.

Ultra-short 230 fs laser pulses of 515 nm wavelength were tightly focused into 700 nm focal spots and utilised in opening ~ 400 nm nano-holes in a Cr etch mask that was tens-of-nm thick. Nano-holes ablated at slightly above the threshold of ablation irradiance became nano-disks and nano-rings at slightly lower pulse energies. Subtle sub-1 nJ pulse energy control was harnessed to pattern large surface areas with controlled nano-alloying of Si and Cr. This technique is extendable to vacuum-free large area patterning of nanolayers by alloying them at distinct locations with sub-diffraction resolution. Such metal masks with nano-hole opening can be used for formation of random patterns of nano-needles with sub-100 nm separation when applied to dry etching of Si.

Background/Aim: Stool gluten immunogenic peptides (GIP) determination is now considered a valuable tool for detecting dietary lapses in treated celiac disease (CeD) patients. Our study aims to explore the diagnostic performance of a qualitative lateral flow immunoassay point-of-care test (LFIA/PoCT) compared with a qualitative enzyme-linked immunosorbent assay (ELISA) for detection of stool GIP. Methods: The study is a post hoc analysis of stool samples collected in the real-life conditions from a cohort of gluten-free diet-treated CeD patients. Stool GIP was measured in µg/g of stool using an ELISA kit (iVYLISA GIP S®, Biomedal SL). For the qualitative evaluation of stool GIP, a LFIA/PoCT test (GlutenDetect®; Biomedal S.L) was employed, which reported results as positive or negative. The LFIA/PoCT performance was evaluated against ELISA, considered as the gold standard. GIP concentrations

The overarching vision of Society 5.0 seeks to integrate technology to enhance the quality of life and address social issues, with the primary goal of creating human-centered communities, which nowadays represent the inhabitants of Smart Cities. In this context, this work addresses the design of a modular strategic platform for the smart supervision of public expenditure, to be used by the Directorate of Information, Analysis, and Immediate Reaction (DIARI) of the General Comptroller of the Republic (CGR) of Colombia as a significant contribution towards the country’s transition into the Society 5.0. The design was performed by conducting a detailed literature review on fiscal control; a comprehensive analysis of the legal, organizational, and technological aspects of the country and the CGR; and developing six functional modules focused on topics such as continuous learning, strategic decision-making, distinctive value, strategic achievements, capacity building, and organization, within a three-year implementation plan, through a participatory approach. This plan aims to integrate the platform to enable real-time monitoring, early detection of irregularities, and increased transparency in the management of data and public resources. The strategic platform for the DIARI of the CGR is useful for Smart Cities and the transition into Society 5.0 since it ensures efficient public expenditure management, enhancing transparency and citizen empowerment through modern technologies, data analytics, and active participation in governance processes.

Hepatitis C virus (HCV) is a major public health threat associated with serious clinical consequences worldwide. The WHO reports an estimated 58 million people globally living with chronic hepatitis C virus (HCV) infection, with 1.5 million new cases and over 350,000 deaths annually due to HCV-related diseases. Despite the existence of multiple diagnostic methods, the accessibility of diagnosis and treatment is often hindered across the continent by limited resources, insufficient healthcare infrastructure, and low public awareness of Hepatitis C virus Hepatitis C virus infection is a major public health concern in African countries, which have the highest prevalence rates of HCV in the world (1–26%). Egypt, African country which had the highest prevalence of Hepatitis C virus infection in the world. Its national hepatitis C elimination initiative emerges as an exemplary case of success an having screened over 60 million individuals, and treated more than 4 million, thereby markedly diminishing both the prevalence and incidence of the disease. The strategies employed by Egypt offer critical insights and adaptable frameworks for other African Countries facing analogous challenges. The Aim of this Review is to highlight the triumphs and hurdles of Egypt's approach, while also providing strategic guidance for African Countries to accelerate the journey towards the eradication of hepatitis C.

The research presented in the article is devoted to the study of the influence of phase compounds on the friability of the Fe-Si-Mn-Al complex alloy. The urgency of the problem lies in the development of technology for producing a non-scatterable alloy from manganese-containing ores and high-ash coals. The main goal of the work is to determine the range of alloy compositions and the resulting phases that affect the dispersibility of the alloy, which is critically important for its industrial implementation. Research methods include thermodynamic diagram analysis (TDA) using data on the standard enthalpy of formation of intermetallic compounds, as well as experimental tests in an ore-thermal electric furnace with a capacity of 200 kV*A. The results show that Fe-Si-Mn-Al complex alloys form a variety of silicide and aluminide phases, including intermetallic compounds and ternary systems, which is critical for understanding and controlling their physicochemical properties. When smelting a complex alloy, the content of leboite (Fe3Si7) in the Fe-Si-Mn-Al system plays a significant role. The development of smelting technology will be aimed at avoiding the FeSi2-Fe3Si7-F2(FeAl3Si2)-Mn11Si19 tetrahedron area. This approach to controlling the composition of a complex alloy is critical to ensuring its consistent friability properties in industrial applications. Thus, this work represents an important step in understanding the physical properties and stability of Fe-Si-Mn-Al complex alloys, which have potential for widespread use in metallurgical and other industrial applications.

Batch and transport experiments were used to investigate the remediation of a loamy sand soil contaminated with Cr(VI) using zero valent iron nanoparticles (nZVI) stabilized by the carboxy methyl cellulose (CMC-nZVI). The effect of pH, ionic strength (IS), and flow rate on the removal efficiency of Cr(VI) were investigated under equilibrium (uniform transport) and non-equilibrium (Two-site sorption) transport using the Hydrus-1D model. The overall removal efficiency ranged from 70 to over 90% based on the chemical characteristics of the CMC-nZVI suspension and the transport conditions. The concentration and pH of the CMC-nZVI suspension had the most significant effect on the removal efficiency and transport of Cr(VI) in the soil. The average removal efficiency of Cr(VI) was increased from 24.1 to 75.5% when the concentration of CMC-nZVI nanoparticles was increased from 10 to 250 mg L-1, mainly because of the increased total surface area at larger particle concentration. Batch experiments showed that removal efficiency of Cr(VI) was much larger under acidic conditions. The average removal efficiency of Cr(VI) reached 90.1 and 60.5 % at pH 5 and 7, respectively. The Two-site sorption model described quite well (r2 = 0.96-0.98) the transport of Cr(VI) in soil as compared to the uniform transport model (r2 = 0.81-0.98). The average retardation of Cr(VI) was 3.51 and 1.61 at pH 5 and 7, respectively, indicating earlier arrival for the breakthrough curves and shorter time to reach maximum relative concentration at lower pH. The Hydrus-1D model has proven to be an efficient tool for assessing the removal of Cr(VI) pollutants, offering innovative, cost-effective, and environmentally friendly remediation methodologies.

More than 90% of patients affected by mastocytosis are characterized by a somatic point mutation of c-KIT, which induces ligand-independent activation of the receptor and downstream signal triggering, ultimately leading to mast cell proliferation and survival. The most frequent mutation is c-KIT p.D816V, but other rarer mutations can also be found. These mutations often have a very low variant allele frequency (VAF), well below the sensitivity of common next-generation sequencing (NGS) methods used in routine diagnostic panels. Highly sensitive methods are developing for detecting mutations. This review summarizes the current indications on the recommended methods and on how to manage and interpret molecular data for the diagnosis and follow-up of patients with mastocytosis.

Vertically aligned Fe, S, and Fe-S doped anatase TiO₂ nanotube arrays are prepared by electrochemical anodization process using an organic electrolyte in which lactic acid is added as an additive. In the electrolyte, nanotube layers of greater length (12 μm) and high order with inner diameter of approx. 90 nm and outer diameter of approx. 170 nm are achieved. Doping of Fe, S, and Fe-S via simple wet impregnation method substituted Ti and O sites with Fe and S, which leads to enhance the rate performance at high discharge current densities. Discharge capacities of TiO₂ tubes increased from 82 mAh g-1 (bare) to 165 mAh g-1 for Fe-S doped TiO₂ at high current densities of 0.3 mAcm-2 after 100 cycles with exceptional capacity retention of 85% after 100 cycles. Owing to the enhancement of thermodynamic and kinetic properties by doping of Fe-S, Li-diffusion increas2ed resulting in remarkable discharge capacities of 143 mAh g-1 and 89 mAh g-1 at a current density of 7.4 mA cm-2 and 19 mA cm-2, respectively.

Cohesion in the refractory metals Cr, Mo, and W is phenomenologically described in this work via a n-body energy functional with a set of physically motivated parameters that were optimized to reproduce selected experimental properties characteristic of perfect and defective crystals. The functional contains four terms accounting for the hard-core repulsion, the Thomas-Fermi kinetic energy repulsion and for contributions to the binding energy of s and d valence electrons. Lattice dynamics, molecular statics, and molecular dynamics calculations show that this model describes satisfactorily thermodynamic properties of the studied metals whereas, unlike other empirical approaches from the literature, predictions of phonon dispersion relations and of surface and point defect energetics reveal in fair good agreement with experiments. These results suggest that the present model is well adapted to large-scale simulations and whenever total energy calculations of thermodynamic properties are unfeasible

Aluminum base alloys containing chromium (Cr) and zinc (Zn) were produced using extrusion and heat treated powder metallurgy. Cr addition ranged between 5 to 10 wt. % while Zn was added in an amount between 0 to 20 wt. %. Heat treatment processes were performed during powder metallurgy process at different temperatures followed by water quenching. Similar alloys were extruded, with an extrusion ratio of 4.6 to get proper densification. Optical microscopy was used for microstructure investigations of the produced alloys. The element distribution microstructure study was carried out using the Energy Dispersive X-ray analysis method. Hardness and tensile properties of the investigated alloys have been examined. Wear resistance tests were carried out and the results were compared with these of the Al-based bulk alloys. Results showed that the aluminum base alloys containing 10wt. % Chromium and heat treated at 500°C for one hour followed by water quenching exhibited the highest wear resistance and better mechanical properties.

In this paper, we present a new concept of the generalized core orthogonality (called the C-S orthogonality) for two generalized core invertible matrices $A$ and $B$. $A$ is said to be C-S orthogonal to $B$ if $A^{\tiny\textcircled{S}}B=0$ and $BA^{\tiny\textcircled{S}}=0$, where $A^{\tiny\textcircled{S}}$ is the generalized core inverse of $A$. The characterizations of C-S orthogonal matries and the C-S additivity are also provided. And the connection between the C-S orthogonality and C-S partial order has been given using their canonical form. Moreover, the concept of the strongly C-S orthogonality is defined and characterized.

Dual generalized commutative quaternions have broad application prospects in many fields. Additionally, the matrix equation AXB = C has important applications in mathematics and engineering, especially in control systems, economics, computer science, and other disciplines. However, research on the matrix equation AXB = C over the dual generalized commutative quaternions remains relatively insufficient. In this paper, we derive the necessary and sufficient conditions for the solvability of the dual generalized commutative quaternion matrix equation AXB = C. Furthermore, we provide the general solution expression for this matrix equation, when it is solvable. Finally, a numerical algorithm and an example are provided to confirm the reliability of the main conclusions.

β-Ga2O3 is a well-known semiconductor material for power devices and other applications. Recently, β-Ga2O3 has also been reported as a scintillator material with a light yield of approximately 8400 ph./MeV, scintillation decay time of <1 μs, and density of 6.44 g/cm3. In this study, 2-inch diameter β-Ga2O3 single crystals were prepared by oxide crystal growth using the cold crucible (OCCC) method under various oxygen partial pressures. In the OCCC method, as in the cold crucible method, a high frequency is applied directly to the oxide materials, which are heated and melted, and the melt is held by the outermost solid material itself that is cooled by water using a copper hearth. In the OCCC method, crystal growth is performed while rotating the seed crystal, as in the Czochralski method, to increase the crystal diameter. The optical properties and radiation responses of the crystals grown under various oxygen partial pressures were evaluated.

This study proposed the combination system consisting of biogas dry reforming reactor and solid oxide fuel cell (SOFC). Since a biogas dry reforming is an endothermic reaction, this study adopted a membrane reactor operated due to the non-equilibrium state with H2 separation from the reaction space. This study aimed to clarify the characteristics of Ni/Cr/Ru catalyst using for a biogas dry reforming membrane reactor. Additionally, this study also investigated the comparison of the characteristics of Ni/Cr/Ru catalyst with that of Ni/Cr catalyst. The impact of operation temperature, the molar ratio of CH4 : CO2, the differential pressure between the reaction chamber and the sweep chamber and the introduction of sweep gas on the characteristics of the biogas dry reforming membrane reactor using Pd/Cu membrane and Ni/Cr/Ru catalyst was examined. The concentration of H2 using Ni/Cr/Ru catalyst was larger than that using Ni/Cr catalyst by 2871 ppmV for the molar ratio of CH4 : CO2 = 1.5 : 1 at the reaction temperature of 600 ℃ and the differential pressure of 0 MPa without a sweep gas, especially. Under this condition, CH4 conversion, H2 yield and thermal efficiency were 67.4 %, 1.77×10-2 % and 0.241 %, respectively.

This study aims to evaluate the effectiveness of inactivating Salmonella enteritidis in fresh chicken breast by irradiation using a combination of short-wave UV (0, 3, 6, 9, 12 and 15 J / cm2) and a natural antimicrobial such as caffeine (0, 5, 10, 15 and 20 nM/g) as alternative proposals to conventional techniques to reduce pathogens in food. The temperatures used were from 2 to 22°C. The most suitable models were double Weibull in 60% of cases with an adjustment of R2 0.9903-0.9553 and Weibull + cola, in 46.67%, with an adjustment of R2 of 0.9998-0.9981. Noting that the most effective combination in the reduction of Salmonella was 12 J/cm2 of UV light and 15 nM/g of caffeine, with a reduction of 6 CFU/g and an inactivation rate of 0.72. The synergistic effect was observed by increasing caffeine and UV light. Furthermore, the physic-chemical characteristics of the food matrix were not affected by the combination of both technologies. Therefore, these results suggest that this combination can be used in the food industry to effectively inactivate Salmonella enteritidis, without deteriorating product quality.

This study presents a novel Fe-CNs-P/S carbon composite material, synthesized by doping elements P and S into NH2-MIL-101 (Fe) using carbonization method. The material's application in sustainable water treatment was evaluated, focusing on its effectiveness in activating persulfate for pollutant degradation. The research thoroughly investigates the synthesis process, structural characteristics, and performance in degrading pollutants. Results indicate that Fe-CNs-P/S-5 with 50% P and S co-doping is higher than that of other samples, where the degradation rate of TC in 30min is as high as 98.11% under the optimum conditions, that is temperature at 25 ℃, 0.05 g/L of catalyst concentration, and 0.2 g/L of PMS concentration. The composite material demonstrates robust versatility and stability, maintaining high degradation efficiency across multiple organic pollutants, with no significant reduction in catalytic performance after four cycles. Furthermore, the free radical quenching experiments displays that the singlet oxygen 1O2 is the main active species. It is demonstrated that the doping of P and S play a role in the enhancement of PMS activation over the Fe-CNs-P/S catalyst. This material demonstrates remarkable efficacy in treating a range of organic contaminants and exhibits excellent reusability, presenting a promising approach for enhancing sustainability in water treatment applications.

A Invasive emerging pollutants from wastewater effluent discharge, such as dyes, pesticides, etc., pose a serious threat to the ecosystem. Advanced oxidation processes (AOPs) under visible light irradiation have emerged as a promising technology to overcome toxic and recalcitrant organic compounds. In this work, the impact of operational factors, including the concentration of Fe3+ or Fe2+, [H2O2], the molar ratio (Oxalate/ Fe3+ or Fe2+), and the initial pH, was studied to obtain high efficiency in the degradation and mineralization of such a food dye to reduce their pollution. The study deals with the comparison of the efficiency of UV, LED, and sunlight irradiation on the photocatalytic degradation of the dye using Fe3+/Lig and Fe2+/Lig complexes. The results showed that sunlight irradiation gave a very rapid kinetic and higher degradation efficiency of over 70%. The optimized conditions for the maximum elimination of the dye with a photocatalytic degradation efficiency (98%) and a mineralization rate of 96% were obtained with the Fe3+/Lig complex, based on the Box Benhken surface design analysis. In the presence of H2O2, the degradation reached an equilibrium stage after 15 min (97.57%) for the Fe(III)/Lig system. Moreover, the inhibition effect of inorganic ions on the photo-Fenton performance of Fe3+/Lig and Fe2+/Lig was studied. The study suggests that the use of nanocrystals of hematite as a Fenton reagent for treating textile effluents needs further investigation. The results showed that the proposed models were well-suited to batch treatment under sunlight. This study not only proposes a Fe3+/Lig and Fe2+/Lig system for the elimination of a food dye without adjusting the pH of the medium, but it also provides insight into the best source of light irradiation for the photocatalytic degradation process.

Since the discovery of transposable elements (TEs) in Maize in the 1940s by Barbara McClintock [1] transposable elements have been described as junk, as selfish elements with no benefit to the host, and more recently as major determinants of genome structure and genome evolution. TEs are DNA sequences that are capable of moving to new sites in the genome and make additional copies while doing so. To limit the propagation of TEs, host silencing mechanisms are directed at transposon-encoded genes that are required for mobilization. The mutagenic properties of TEs, the potential of TEs to form new genes and affect gene expression, together with the host silencing mechanisms shape eukaryotic genomes and drive genome evolution. While TEs constitute more than half of the genome in many higher eukaryotes, transposable elements in the nematode C. ele-gans form a relatively small proportion of genome, about 15% [2]. Genetic studies of transposon silencing and the discovery of RNAi in C. elegans, propelled C. elegans to the forefront of studies of RNA-based mechanisms that silence TEs. Here, I will review the transposable elements that are present and active in the C. elegans genome, and the host defense mechanisms that silence these elements.

The endophytic fungus Aspergillus sp. SPH2 was isolated from the stems of the endemic plant Bethencourtia palmensis and its extracts were found to have strong fungicidal effects against Botrytis cinerea and ixodicidal effects against Hyalomma lusitanicum at different fermentation times. In this study, the fungus was grown using three different culture media and two methodologies, Microparticulate Enhancement Cultivation (MPEC) and Semi-Solid Fermentation (SSF), to increase the production of secondary metabolites in submerged fermentation. The addition of an inert support to the culture medium (SSF) resulted in a significant increase in extract production. However, when talcum powder was added to different culture media, unexpected results were observed, with a decrease in the production of the biocompounds of interest. Metabolomic analyses showed that the production of aspergillic, neoaspergillic, and neohydroxyaspergillic acids peaked in the first few days of fermentation, with notable differences observed among the methodologies and culture media. Mellein production was particularly affected by the addition of an inert support to the culture medium. These results highlight the importance of surface properties and morphology of spores and mycelia during fermentation by this fungal species.

This work investigated the isothermal holding time dependence of the densification, microstructure, weight loss and tensile properties of Fe-Mn-Si powder compacts. Elemental Fe, Mn and Si powder mixtures with a nominal composition of Fe-28Mn-3Si (in weight percent) were ball milled for 5h and subsequently pressed under a uniaxial pressure of 400 MPa. The compacted Fe-Mn-Si powder mixtures were sintered at 1200 ℃ for 0, 1, 2 and 3 h, respectively. In general, the density, weight loss and tensile properties increased with the increase of isothermal holding time. A significant increase in density, weight loss and tensile properties occurred in the compacts isothermally holding for 1 h, as compared to those with no isothermal holding. However, further extension of isothermal holding time (2 and 3 h) only played a limited role in promoting the density and tensile properties. The weight loss of the sintered compacts was mianly caused by the sublimation of Mn in Mn depletion region on the surface layer of the sintered Fe-Mn-Si compacts. The length of the Mn depletion region increased as isothermal holding time increased. A single α-Fe phase was detected on the surface of all the sintered compacts, and the locations beyond the Mn depletion region were comprised of a dual dominant γ-austenite and minor ε-martensite.

The high flammability and lack of charrability of polystyrene (PS) pose significant limitations on its broader applications. Therefore, there is an urgent need for a straightforward and efficient method for the synthesis of flame-retardant PS, which still poses a considerable challenge. In this study, we present an efficient approach to enhance the flame-retardant properties of PS through direct phosphorylating aromatic C(sp2)-H bonds using commercially available and inexpensive manganese catalyst. A range of phosphonates served as reactive substrates to enable a tunable degree of polymer functionalization. The corresponding phosphorylated PS specimens were determined by means of 1H NMR, 31P NMR, FTIR spectroscopy and GPC. Microscale combustion calorimetry (MCC) tests indicate that this protocol indeed enhances the flame-retardant performance of PS. Moreover, other advantages associated with the incorporation of the phosphonate group have been observed, including improved thermal resistance and wettability. This cost-effective strategy of Mn-catalyzed C-H can also be utilized to directly obtain phosphonate modification of waste foamed PS and styrene acrylonitrile copolymer, providing a new method for the purpose of recycling and upgrading PS plastics.

An H-bond involves the sharing of a hydrogen atom between an electronegative atom to which it is covalently bound (the donor) and another electronegative atom serving as an electron acceptor. Such bonds represent a critically important geometrical force in biological macromolecules and, as such, have been characterized extensively. H-bond formation invariably leads to a weakening within the acceptor moiety due to the pulling exerted by the donor hydrogen. This phenomenon can be compared to a spring connecting two masses; pulling one mass stretches the spring, similarly affecting the bond between the two masses. Herein, we describe the opposite phenomenon when investigating the energetics of the C-H...O=C bond. This bond underpins the most prevalent protein transmembrane dimerization motif (GxxxG) in which a glycine C-H on one helix forms a hydrogen bond with a carbonyl in a nearby helix. We use isotope-edited FT-IR spectroscopy and corroborating computational approaches to demonstrate a surprising strengthening of the acceptor C=O bond upon binding with the glycine C-H. We show that electronic factors associated with the C-H bond strengthen the C=O oscillator by increasing the s-character of the -bond, lowering the hyperconjugative disruption of the -bond. In addition, a reduction of the acceptor C=O bond’s polarity is observed upon the formation of the C-H...O=C bond. Our findings challenge the conventional understanding of H-bond dynamics and provide new insights into the structural stability of inter-helical protein interactions.

Interferon-gamma (IFN-γ) is an important cytokine in host defense against tuberculosis infection. In some cases, administration of IFN-γ during tuberculosis infection can promote faster cure. In the present work, we have shown that in a mouse model, human interferon-gamma, exhibits some anti-tuberculosis activity, especially in combination with isoniazid.

L-Theanine, a unique non-protein amino acid, is an important bioactive component of green tea. Previous studies have shown that L-theanine has many potent health benefits, such as anti-anxiety effect, regulation of immune response, relaxing neural tension, reducing oxidative damage. However, little is known concerning whether L-theanine can improve the clearance of mitochondrial DNA (mtDNA) damage in organisms. Here, we reported that L-theanine treatment increased ATP production and improved mitochondrial morphology to extend the lifespan of UVC-exposed nematodes. Mechanistic investigations showed that L-theanine treatment enhanced the removal of mtDNA damage and extended lifespan by activating autophagy, mitophagy, mitochondrial dynamics, and mitochondrial unfolded protein response (UPRmt) in UVC-exposed nematodes. In addition, L-theanine treatment also up-regulated the expression of genes related to mitochondrial energy metabolism in UVC-exposed nematodes. Our study provided a theoretical basis for the possibility that tea drinking may prevent mitochondrial related diseases.

A mild, efficient, and photocatalytic synthesis of 6-phosphorylated phenanthridines via tandem radical addition/cyclization/aromatization of 2-isocyanobiphenyls with diarylphosphine oxides is reported. The method features operational simplicity, metal-free conditions, using low-cost rose Bengal as catalyst and sustainable air as terminal oxidant at room temperature, and providing the desired products in moderate to good yields.

Biological neural network (BNN) is the core brain for creature to accomplish its intelligent behaviors through unique network structure and mechanisms. It also inspires controlling human-designed autonomous agents including robots to generate more advanced intelligent behaviors by mimicking the neural control mechanism of creatures at a deeper and more interactive level. Here, we constructed a whole-brain neural network model of Caenorhabditis elegans (C. elegans), which characterizes the electrochemical processes at the level of cellular synapse. The neural network simulation integrates computational programming and visualization of neurons and synapse connections of C. elegans, containing the specific controllable circuits summarization with their dynamic characteristics within the whole network. To illustrate its particular intelligent control capability in terms of robotics, we introduce the first innovative methodology for applying the BNN model to a 12-legged robot’s movement control based on the established numerical simulation platforms. We accomplished and designed two methods and corresponding encoding processes, one involving orientation control and the other involving locomotion generation, to demonstrate the intelligent control performance of BNN. Both simulation and experiment results indicate that the robot exhibits stronger autonomy and more intelligent moving performance under the control of BNN. We then summarized the contributions for digitalizing the C. elegans’ whole-brain neural network in real-time and utilizing it to control robot in a closed loop to validate its advanced intelligence control ability in terms of a scientific robot.

In this work we have investigated the accumulation of ryanoids in different plant parts (leaves, stems roots) of aeroponically grown Persea indica cloned trees (one year old cloned individuals) and a selected mature wild tree. We have tested the insect antifeedant (against Spodoptera littoralis, Myzus persicae and Rhopalosiphum padi) and nematicidal (against Meloidogyne javanica) effects of ethanolic extracts from these different plant parts. The HPLC-MS analysis of P. indica extracts showed that the mature tree (wild) leaves had 2 times more chemical diversity than the stems. The aeroponic plants showed lower differences in chemical diversity between leaves and stems, with the lowest diversity found in the roots. The ryanodane epiryanodol (1) was present in all the plant parts, with the mature stems (wild) having the highest amount. The aeroponic stems also accumulated ryanoids including 1, cinnzeylanol 2 and cinnzeylanone 4. The insect Spodoptera littoralis was strongly affected by the stem extracts while the leaf ones were moderately active. Based on the predicted vs. the real antifeedant values we conclude that the ryanoid content (1 or a combination of 2, 4 and 1) explained the antifeedant effects of the stem extracts while addition-al components contributed to the activity of the leaf ones. Therefore, careful individual selection of P. indica seedlings should be carried out prior to proceed with its aeroponic cultivation in or-der to obtain ryanodane-rich stem or leaf extracts with strong antifeedant effects on S. littoralis.

Darier disease (DD) is an autosomal dominant disorder due to mutation of ATP2A2 gene causing an isolated skin manifestation based on keratinocyte disconnection and apoptosis. Systemic manifestations of DD have not been demonstrated so far although a high incidence of neuropsychiatric syndromes suggest an involvement of central nervous system. A Novel ATP2A2 Gene Mutation c.118G>A, causing keratinocyte and cardiomyocyte disconnection in Darier disease, is reported. Their common pathologic pathway, still unreported, was documented by both skin and left ventricular endomyocardial biopsy because of cardiac dilatation and dysfunction appeared several decades after skin manifestations.Keratinocyte disconnection was paralleled by cardiomyocyte separation at lateral junction. Cardiomyocyte separation was associated to cell disarray, sarcoplasmic reticulum dilatation and increased myocyte apoptosis. Clinically, hyperkeratotic skin papules were associated to chest pain, severe muscle exhaustion and ventricular arrhythmias that improved following administration of aminophylline, a phosphodiesterase inhibitor enhancing SERCA2 protein phosphorylation.Specific mutations of ATP2A2 gene may cause cardiac involvement in patients with DD. Cardiac pathologic changes are similar to those documented in the skin including cardiomyocyte disconnection that promotes precordial pain and cardiac arrhythmias. Phosphodiesterase inhibitors, enhancing SERCA2 protein phosphorylation may substantially attenuate the symptoms.

Background. Respiratory distress syndrome (RDS) is the primary cause of respiratory failure in preterm infants, but it also affects 5-7% of term infants. Dysfunctions in pulmonary surfactant metabolism, resulting from mutations of the lung surfactant genes, are rare diseases, ranging from fatal neonatal RDS to interstitial lung disease, associated with increased morbidity and mortality. This study aims to clarify the clinical significance of ABCA3 variants found in a specific family case, as existing data in the literature is inconsistent. Material and methods: A family case report was conducted; targeted panel genetic testing identified a variant of the SFTPB gene and two variants of ABCA3 genes. Comprehensive research involving a systematic review of PubMed, Google Scholar databases, and genome browsers was used to clarify the pathogenicity of the two ABCA3 variants found in the index patient. Advanced prediction tools were employed to assess the pathogenicity of the two ABCA3 variants, ensuring the validity and reliability of our findings. Results: The index case exhibited fatal neonatal RDS. Genetic testing revealed the presence of the SFTPB p.Val267Ile variant, not previously reported, a benign variant based on family genetic testing and history. Additionally, two ABCA3 gene variants were identified: c.697C>T, not yet reported, and c.838C>T. These variants were found to affect ABCA3 protein function and were likely associated with neonatal RDS. Prediction tools and data from nine other cases in the literature supported this conclusion. Conclusions: Based on in silico predictors, analysis of the presented family, and cases described in the literature, it is reasonable to consider reclassifying the two ABCA3 variants identified in the index case as pathogenic/pathogenic. Reclassification will improve genetic counseling accuracy and facilitate correct diagnosis.

There are few longitudinal studies on the association between dietary vitamin C and sleep disorders. The aim of this study was to investigate the association between dietary vitamin C intake and various types of sleep disorders, including sleep apnea and insomnia, as well as recommended dietary intakes. A total of 68,221 participants from the UK Biobank were enrolled in the study. Dietary vitamin C intake was calculated by a 24-hour dietary recall questionnaire. We used Cox regression model to assess the association between dietary vitamin C and sleep disorders and restricted cubic spline models to explore potential nonlinear relationships. Stratified analyses and sensitivity analyses were also performed to further test the results. The results showed that vitamin C intake at the Q4 level (132.88-191.51 mg/d) was significantly protective against sleep disorders with an HR (95% CI) of 0.78 (0.65-0.94), and against sleep apnea with an HR (95% CI) of 0.75 (0.62-0.92). The protective effect remained significant in stratified analyses of men and age ≤60 years, and the results were robust in sensitivity analyses. Adequate dietary vitamin C intake may have a protective effect in preventing sleep disorders.

Recently, we studied CR-slant warped products B1×fM⊥, where B1=MT×Mθ is the Riemannian product of holomorphic and proper slant submanifolds and M⊥ is a totally real submanifold in a nearly Kaehler manifold. In the continuation, in this paper, we study B2×fMθ, where B2=MT×M⊥ is a CR-product of a nearly Kaehler manifold and establish Chen’s inequality for the squared norm of the second fundamental form. Some special cases of Chen’s inequality are given.

Salmonella Typhimurium is a typical Gram-Negative bacterium associated with food-borne illness threatening public health. This pathogen is reported to have caused millions of infections and thousands of hospitalizations yearly in the United States alone. Salmonella Typhimurium has a sophisticated array of virulent factors, including its flagella, which contributes significantly to its pathogenicity. Cannabidiol (CBD), the non-psychoactive component of the cannabis plant, has attracted the interest of many researchers recently because of its antimicrobial properties. With the growing interest in exploring CBD’s antimicrobial properties, we, in this study, have delved into unravelling how prolonged exposure of Salmonella Typhimurium to CBD influences the expression of the flgA gene. We hypothesized that the exposure of Salmonella Typhimurium to CBD may result in flgA upregulation, causing the bacteria to withstand various stresses and potentially enhance its survival rates and pathogenicity. We have employed several assays, such as mRNA expression, motility assays, pH induction assays, nutrient starvation interventions, and biofilm analysis, to explore the influence of CBD on the pathophysiology of Salmonella Typhimurium. Our findings reveal that CBD-resistant strains exhibit enhanced resilience to extreme pH levels and motility and survive poorly under nutrient starvation, with more robust biofilm formation compared to the susceptible strains. The results contribute to the broader comprehension of CBD resistance mechanisms in bacteria. This work provides insight into the potential therapeutic interventions for controlling CBD-resistant bacterial infections. This study also underscores the essence of exploring novel alternative antimicrobial agents to tackle the ever-persistence of bacterial antibiotic resistance.

The existences of the N→C dative bonds in the complexes between N-containing molecules and fullerenes have been verified both theoretically and experimentally. However, finding stable N→C dative bonds is still a highly challenging task. In this work, we investigated computationally the N→C dative bonds in the complexes formed by fullerene C60 with 1,2,5-chalcogenadiazoles, 2,1,3-benzochalcogenadiazoles and 1,2,4,5-chalcogenatriazoles, respectively. It was found that the N→C dative bonds are formed along with the formation of the N–Ch···C (Ch = S, Se, Te) chalcogen bonds. In the gas phase, from S-containing complexes through Se-containing complexes to Te-containing complexes, the intrinsic interaction energies become more and more negative, which indicates that the N–Ch···C chalcogen bonds can facilitate the formation of the N→C dative bonds. The intrinsic interaction energies are compensated by the large deformation energy of fullerene C60. The total interaction energies of Te-containing complexes are negative, while both of the total interaction energies of S-containing complexes and Se-containing complexes are positive. This means that the N→C dative bonds in the Te-containing complexes are more easily observed in experiments in comparison with those in the S-containing complexes and Se-containing complexes. This study provides a new theoretical perspective on the experimental observation of the N→C dative bonds in the complexes involving fullerenes. Further, the formation of stable N→C dative bonds in the complexes involving fullerenes can significantly change the properties of fullerenes, which will greatly simulate and expand the application range of fullerenes.

Background: A new coronavirus (SARS-CoV-2) that emerged from Wuhan, Hubei Province, China, has spread throughout the world and is declared a pandemic by the World Health Organization (WHO). A lot remains to be understood of SARS-CoV-2 and the disease (COVID-19). SARS-CoV-2 has until recently been identified as responsible for both asymptomatic and serious life-threatening infections. The unavailability of specific therapeutic agents is a major hurdle in the treatment and management of COVID-19 patients. The present review attempts to evaluate the immunobiochemical aspects of the pathogenesis, diagnosis, and management of SARS-CoV-2 infection. Main Body: This review is a comprehensive evaluation of the data collected through various sources, including Google Scholar, PubMed, and Scopus. The articles were searched and selected using key words such as “Coronavirus disease (COVID-19)”, “Diagnosis of COVID-19”, Pathogenesis of Covid-19”, “management of COVID-19”, “Immunology of COVID-19”, and “Complications of COVID-19”. The study noted that the novel Coronavirus infection could result in an exaggerated immune response, causing a cytokine storm and damaging several organs of the body. The infected patients develop several complications, including immunological, hematological, and biochemical alterations. Consequently, COVID-19 patients may develop cardiovascular, liver, renal, and neurological complications, among others. Conclusion: An increased understanding of the immunobiochemical aspects of the disease may contribute to better management of SARS-CoV-2-infected persons, as evidenced from the available literature. A holistic approach to the management of COVID-19 patients taking into consideration the effect of COVID-19 infection on various organs of the body assumes increased significance in patient management.

The combination of several therapeutic strategies is often seen as a good way to decrease the resistance rates, since bacteria overcome better single-drug treatments than multi-drug ones. This strategy is especially attractive when several targets and subpopulations are affected, as it is the case of Klebsiella pneumoniae persister cells, a subpopulation of bacteria able to transiently survive antibiotic exposures. This work aims to evaluate the potential of a repurposed anticancer drug, mitomycin C, combined with the K. pneumoniae lytic phage vB_KpnM-VAC13 in vitro and the safety in an in vivo murine model against two clinical isolates of this pathogen, one of them exhibiting an imipenem-persister phenotype. At the same time, we verified the absence of toxicity of mitomycin C at the concentration using the human chondrocyte cell line T/C28a2. The viability of these human cells was checked both by cytotoxicity assays and flow cytometry.

This study presents the synthesis and electrochemical evaluation of nitrogen-doped vanadium oxide (N-V2O3/C) as a cathode material for aqueous zinc-ion batteries (AZIBs), using a hydrothermal method. Compared to undoped V2O3/C, N-V2O3/C exhibits enhanced electrical conductivity, capacity, and electrochemical kinetics, attributed to the incorporation of pyridinic and pyrrolic nitrogen. Initial charge-discharge cycles indicate phase transitions to amorphous vanadium oxides, enhancing conductivity. N-V2O3/C shows a high specific capacity of 168.4 mAh g−1 at 10 A g−1 and remarkable reversibility, highlighted by the transient existence of intermediate species during cycling. Optimal electrochemical performance is achieved with a vanadium to nitrogen molar ratio of 2:3, indicating the significant impact of nitrogen doping concentration on the material’s efficiency. This work underscores the potential of N-V2O3/C as a superior cathode material for AZIBs.

Abstract: Panfacial fractures are complex injuries involving multiple regions of the facial skele-ton simultaneously, which may necessitate multiple surgeries over a relatively short period. They are often associated with polytrauma and other injuries including brain trauma, which re-quire either immediate airway management, prolonged intubation, or repeated intubations for staged surgeries. Given the frequent need for intermaxillary fixation and the potential involve-ment of the central nasal complex or skull base, conventional oro-tracheal or nasotracheal intu-bation often presents challenges. Submental intubation is the most reported method of airway management with the aim to avoid tracheostomy and its related complications. A review of the different techniques of airway management in the elective treatment of panfacial fractures was performed focusing on the advantages and disadvantages of each method. Most of the literature consisted of retrospective studies, with only one prospective study comparing submental intu-bation to tracheostomy in panfacial fractures. There is abundant literature that favours the sub-mental intubation for its rapid establishment and low complication rate. Other techniques less reported were retromolar intubation, nasotracheal to orotracheal switch, tracheostomy or crico-thyroidotomy. An algorithm for the management of the airway in panfacial fractures is pre-sented.

The endocannabinoid system (ECS) is a complex neuromodulatory network in the human body that have enormous impact in developing the central nervous system, as well as modulates various physiological processes. The ECS is made up of anandamide, 2-arachidonoylglycerol (2-AG), which are responsible for the synthesis and degradation of endocannabinoids, and enzymes such as FAAH and MAGL ensures the precise control over endocannabinoid levels. The ECS relies on CB1 receptors found in the central nervous system (CNS), and CB2 receptors found in the peripheral nervous system and immune cells. Dysregulation of the ECS has been associated with several health conditions, prompting investigations into its association with phytocannabinoids to harness their therapeutic potential. The ECS is intricately linked with the nervous system, and it is known to modulate neuronal activities in the CNS, influencing pain and mood modulation. The ECS is also associated with neuropathies-peripheral nerve damage leading to symptoms such as weakness, numbness and pain as evidenced in diabetic neuropathy, Guillain-Barré Syndrome, carpal tunnel syndrome, peripheral neuropathy, and postherpetic neuralgia. The focus of this review is on the interplay between 2-arachidonoylglycerol and anandamide amidohydrolase in neuropathy, elucidating their roles in pain regulation, inflammation, and specific neuropathies. The knowledge generated is expected to have broad implications, providing comprehensive insights into neuropathic conditions and how to improve on them. Ultimately, this understanding may lead to more effective treatments and improved quality of life for individuals affected by these conditions.

To clarify the risk factors for aggravation of esophagogastric varices (EGV) after hepatitis C virus (HCV) eradication with direct-acting antiviral (DAA) therapy, we enrolled 167 consecutive patients with HCV-related compensated cirrhosis who achieved a sustained virological response (SVR) after DAA therapy. During a median of 69 months, EGV was aggravated in 42 (25%) patients despite SVR. The cumulative 1, 3, 5, and 10-year aggravated EGV rates were 7%, 23%, 25%, and 27%, respectively. Multivariate analysis identified platelet count <11.0×10⁴/μL, LSM ≥18.0 kPa, total bile acid ≥33.0 μmol/L, and diameter of left gastric vein (LGV) ≥5.0 mm at HCV eradication as independent risk factors for EGV aggravation post-SVR. In groups that meet all of these risks, the cumulative EGV aggravation rates at 1, 3, and 5 years were 27%, 87%, and 91%, respectively. However, none of the patients who had only one or none of the risk factors experienced EGV aggravation. Platelet count, LSM, total bile acid, and diameter of LGV at HCV eradication were associated with aggravated EGV post-SVR. EGV tends to worsen as two or more of these risk factors increase.

The Great Reset has been presented by the World Economic Forum (WEF) in response to the COVID-19 pandemic in 2022 as a model through which a “stakeholder economy” would achieve “resilient, equitable and sustainable” economic, social and environmental goals. A more equitable distribution of resources, better working conditions, and ecological transitions are included in a social, economic and environmental reform agenda. This article raises the question of whether the Great Reset project should be interpreted as a “realistic utopia” and what is its reform potential. In an attempt to answer the question of whether the Great Reset as a realist utopia is consistent with the current state of science and philosophy, the article re-examines the idea of utopia in the light of recent philosophical and scientific approaches, such as critical realism in philosophy, so-cial systems theory in sociology and complexity theory in science. A comparative conceptual analysis is carried out and discussed introducing the idea of a realist utopia in Rawls' theory of justice as fairness. In the final discussion, some doubts are raised about the logical coherence, rigor of scientific theorizing, policy prescriptions, and predictive potential of the Great Reset emerging paradigm. It is concluded that utopian projects of radical reform can become realistic when they offer explanations of the deep structural changes that underlie social and economic evolution, drawing from these explanations the policy implications and prescription that can support struc-tural changes, rather than from assumed long-term effects of exogenous shocks or “black swan” events such as the COVID-19 pandemic.

Nickel-base superalloys like VDM 780 may possess a high content of Cr and Co. This influences solution energies of phase-forming elements like Al and Ta (γ′-phase), Nb (γ′′- and δ-phase), and Ti (η-phase). We perform density functional theory studies of a nickel matrix at 0 K with high concentrations of either Co and Cr and calculate the influence of these elements on solution energies. In the case of Co, the solution energy can be predicted well by the nearest-neighbor interaction in the Co-rich matrix. For Cr, the effect is more complicated because Cr has a larger ionic radius and changes the magnetic state of the material. The effect of a Cr-rich matrix on the energy of Co is dominated by magnetic effects, interactions with the other elements by elastic deformation of the lattice.

Optical characterization and thermal aging tests are performed on a sputter-deposited coating, consisting of SiO₂/Cr₂O₃/Cr/Cr₂O₃ layers, designed and developed as a selective solar absorber to be used for unconcentrated solar thermal applications. Both measurements are performed by using a home-made apparatus, which mimics a flat plate collector under high vacuum. A Performance Criterion (PC_η(T)), based on absorber efficiency is proposed, and a forecast of service lifetime is obtained. As a result of the thermal aging tests, the selective solar absorber under study appears to be highly efficient at mid temperatures (up to 573 K) and thermally stable at temperatures (up to 690 K).

A highly efficient reduction process of Cr (VI) with biochar was conducted in this paper. The results showed that nearly 100% Cr (VI) was reduced at selected reaction conditions: the dosage of biochar at m (C)/m(Cr) = 3.0, reaction temperature of 90 ℃, reaction time at 60 min and concentration of H2SO4 of 20 g/L, respectively. The reduction kinetics analysis demonstrated that the reduction of Cr (VI) fitted well with the pseudo-first-order model and the apparent activation energy was calculated to 40.24 kJ/mol. Response surface methodology confirmed that all the experimental parameters had positive effect on the reduction of Cr (VI). The influence of each parameter on the reduction process followed the order: dosage of biochar> Concentration of H2SO4 > Reaction Temperature > Reaction Time. This paper provided a versatile strategy for treatment of wastewater containing Cr (VI) and showed a bright tomorrow for wastewater treatment.

The photosystem I (PSI) of the green alga Chlamydomonas reinhardtii associates with 10 light-harvesting proteins (LHCI) to form the PSI-LHCI complex. Binding of LHCII to PSI may also occur and is controlled by a process called state transitions. Hereby, two LHCII trimers bind to the PSAL, PSAH and PSAO side of PSI to produce the PSI-LHCI-LHCII complex. In this work, we took advantage of chemical crosslinking of proteins in conjunction with mass spectrometry to identify protein-protein interactions between the light-harvesting proteins of PSI and PSII. We detected binding of LHCBM proteins to the LHCA1-PSAG side of PSI and identified protein-protein interactions of LHCSR3 with LHCA5 and LHCA3. Our data indicate that the binding of LHCII to PSI is more versatile as anticipated and reveal that LHCSR3 likely regulates excitation energy transfer to the PSI core via LHCA5/LHCA3.

Iron-based materials are widely applied in Fenton chemistry and they have promising prospects in the processing of wastewater. The composition complexity and rich chemistry of iron and/or oxides, however, hamper the precise understanding on the active sites and the working mechanism which still remain highly controversial. Herein, iron oxides of four different model systems are designed through a conventional precipitation method plus H2 reduction treatment. These systems feature Fe@Fe3O4 with abundant oxygen vacancy, Fe0 and Fe3O4 particles with interface structures, and Fe3O4-dominated nanoparticles of different sizes. These materials are applied in the decomposition of methyl orange as a model reaction to assess the Fenton chemistry. The Fe@Fe3O4 with core-shell structures exhibited significantly higher decomposition activity than the other Fe3O4-rich nanoparticles. A thin Fe3O4 layer formed by auto-oxidation of iron particles when exposing to air can boost the activity as compared with the Fe0 and Fe3O4 particles with interface structures but poor oxygen vacancy. The unique hetero-structure with the co-existence of both metallic iron and oxygen vacancy displayed excellent redox propensity which might account for the superior Fenton activity. This finding provides a new perspective to understand and design highly efficient iron-based Fenton catalysts.

In patients with primary central nervous system lymphoma (PCNSL), the choice of surgical strategy for histopathologic assessment is still controversial, particularly in terms of preoperative corticosteroid (CS) therapy. To provide further evidence for clinical decision-making, we retrospectively analyzed data from 148 consecutive patients who underwent surgery at our institution. Although patients treated with corticosteroids preoperatively were significantly more likely to require a second or third biopsy (p=0.049), it was only necessary in less than 10% of the cases with preoperative corticosteroid treatment. The choice of surgical procedure did not affect diagnostic accuracy (p&gt;0.05). Preoperative CSF sampling did not provide additional information but was associated with delayed surgery (p=0.02). Surprisingly, diagnostic accuracy was significantly lower when patients were treated with anticoagulation or dual antiplatelet therapy (p=0.015). In conclusion, preoperative CS therapy can challenge the histological diagnosis of PCNSL. At the same time, our data suggest that preoperative CS treatment only presents a relative contraindication for an early surgical intervention. The standard surgical approach is stereotactic biopsy, but other approaches can be individually considered. If a definitive diagnosis cannot be made after the first surgical intervention, the timing of a repeat biopsy after discontinuation of CS remains a case-by-case decision.

L-gulonolactone oxidase enzyme (GULO) catalyzes the last step of L-ascorbic acid (vitamin C) biosynthesis. This enzymatic activity is lost in primates. The full-length rat GULO has been previously produced in plants and demonstrated to be active. In this study, we compare activity of two variants of GULO produced in Escheriachia coli cells, full-length rat GULO (fGULO) and its C-terminal catalytic domain (cGULO). The expression and purification of the recombinant proteins were optimised and their biological activity was confirmed by two methods, the GULO activity assay in the protein extracts and the ‘in-gel’ staining for GULO activity. Both variants of recombinant GULO were biologically active in both assays. However, cGULO is more promising than fGULO for ascorbic acid production because it is more efficiently produced by bacteria.

Background/Objectives: Multisystem Inflammatory Syndrome in children (MIS-C) is a rare but severe post-infectious complication of COVID-19, that often requires admission to the Pediatric Intensive Care Unit (PICU). The present study aimed to compare the demographic, clinical and laboratory characteristics between children diagnosed with MIS-C who were admitted to the PICU or did not require PICU admission. Methods: Children diagnosed with MIS-C from September 2020 to April 2023 were included in this case-control study. Patient’s demographic, clinical and laboratory data, were collected from medical records. Results: Fifty children with MIS-C were included in the study [median (IQR) age: 7.5 (4.3, 11.4) years, 28/50 (56%) males]. Twenty-two (22/50, 44%) children required admission to the PICU. In the multivariate regression analysis, hepatic (OR:12.89, 95%CI: 1.35-123.41, p-value=0.03) and cardiological involvement (OR:34.55, 95%CI: 2.2-541.91, p-value=0.01) were significantly associated with hospitalization at the PICU. Regarding the laboratory and imaging parameters during the first 48 hours from admission, D-dimer levels higher than 4μg/mL and decreased Left Ventricular Ejection Fraction were associated with an increased risk of PICU admission (OR:7.95, 95%CI:1.48-42.78, p-value=0.02 and OR=1.28, 95%CI:1.07-1.53, p-value=0.01). Children who were admitted to the PICU were more likely to develop complications during their hospitalization (10/22, 45.5% vs. 3/28, 10.7%, p-value=0.005) and were hospitalized for more days, than children in the pediatric wards (median length of stay (IQR): 20 (15,28) days vs. 8.5 (6, 14) days, p-value&lt;0.001). Conclusions: In the present study, cardiovascular, hepatic involvement and increased D-dimer levels in children with MIS-C were associated with admission to the PICU.

Increasing pesticide resistance in plant pathogens is major concern in agriculture production. Research on ecofriendly alternatives of chemical pesticides are more in demand in pesticide industry. In the current study, an ethyl acetate extract from the endophytic fungus Trichoderma sp. EFI 671, isolated from the stem parts of the medicinal plant Laurus sp., was screened for bioactivity against plant pathogens (Fusarium graminearum, Rhizoctonia solani, Sclerotinia sclerotiorum and Botrytis cinerea), insect pests (Spodoptera littoralis, Myzus persicae, Rhopalosiphum padi) and plant parasites (Meloidogyne javanica). The bioactive components have been characterized following a bioassay-guided isolation against M. persicae. The chemical study of this bioactive extract resulted in the isolation of 1-oleoyl-2-linoleoyl-3-palmitoylglycerol (1), eburicol (2), (24R)-stigmast-4-ene-3-one or β-sitostenone (3), ergosterol (4) and ergosterol peroxide (5). The free fatty acids present in compound 1 (oleic, linoleic and palmitic) showed strong dose-dependent aphid antifeedant effects against M. persicae. Liquid (PDB, and SDB) and solid (corn, sorghum, pearl millet and rice) growth media were tested in order to optimize the yield and bioactivity of the fungal extracts. Pearl millet and corn gave the highest extract yields. All the extracts from these solid media had strong effects against M. persicae with sorghum being the most active. Corn increased the content in linolenic, pearl millet the oleic and stearic and sorghum oleic and linolenic acids compared to rice. Their antifeedant effects correlated with linoleic /oleic acids. The phytotoxic effects of these extracts against Lolium perenne and Lactuca sativa varied with culture media, with sorghum being the least toxic.

The α(1,2)fucosyltransferase (Se enzyme) encoded by FUT2 is involved in the secretor status of ABH(O) blood group antigens. The sedel2 allele is one of the non-functional FUT2 (se) alleles in which 9.3 kb containing the entire coding region of FUT2 is deleted by Alu-mediated nonhomologous recombination. In addition to this allele, three SNPs of FUT2, c.375A>G, c.385A>T, and c.571C>T, appear to be prevalent in certain Oceanian populations such as Polynesians. Recently, we developed an endpoint genotyping assay to determine the sedel2 zygosity, using a FAM-labeled probe for detection of the sedel2 allele and a VIC-labeled probe for detection of FUT2. In this study, instead of the VIC probe, a HEX-labeled probe covering both c.375A>G and c.385A>T and a Cy5-labeled probe covering c.571C>T were added to the sedel2 allele assay mixture to allow simultaneous detection of these four variations by endpoint genotyping for the sedel2 zygosity and fluorescence melting curve analysis for c.375A>G, c.385A>T, and c.571C>T genotyping. The results obtained from 24 Samoan subjects with this method were identical to those obtained with previous methods. Therefore, it appears that present method can accurately determine these four variations simultaneously.

In the present study, the corrosion resistance of amorphous coating and composite coatings in 3.5 wt.% NaCl, 0.5 M H₂SO₄ and 10 wt.% NaOH solution were studied. The composite coatings exhibit superior corrosion resistance. When the content of AT13 （Al₂O₃–13 wt.% TiO₂）was 15 wt.%, the composite coating has the lowest corrosion current density (1.75×10^-6 A cm^-2), which is 5.14×10^-5 A cm^-2 for Fe-based metallic glassy coating, and the highest corrosion potential (-411 mV), which is -580 mV for Fe-based metallic glassy coating. The breakdown potential of the passivation film in 3.5 wt.% NaCl solution was much higher than that of 316L.The long-time immersion corrosion tests carried out on different coatings showed that the corrosion protection effect of coating was enhanced with the increase of the amount of AT13 added.

This research investigated high-temperature corrosion (500 °C) of Cr-Mo steel processed using water jet peening or multifunction cavitation (MFC), and the suitability of such steel for high-temperature boilers and reaction vessels. High-temperature corrosion was induced using an embedment test and a coating test using sulfide-type K2SO4-Na2SO4 powder. To measure the relaxation of the residual stress due to the decrease in work hardening caused by an increase in specimen temperature and the difference in thermal shrinkage between the surface and interior of the specimen, a thermal cycling test was conducted. For the MFC-processed specimen, the oxide film that formed on the surface suppressed mass loss, prevented crack formation, and reduced the compressive residual stress caused by high-temperature corrosion. MFC-processed Cr-Mo steel is thus suitable for a high-temperature corrosion environment.

Background: Leishmaniasis is a significant global public health issue that is caused by parasites from Leishmania genus. With limited treatment options and rising drug resistance, there is a pressing need for new therapeutic approaches. Molecular chaperones, particularly Hsp90, play a crucial role in parasite biology and are emerging as promising targets for drug development. Objective: This study evaluates the efficacy of 17-DMAG in treating BALB/c mice from cutane-ous leishmaniasis through in vitro and in vivo approaches. Materials and Methods: We assessed 17-DMAG cytotoxic effect on bone marrow-derived mac-rophages (BMMΦ) and its effects against L. braziliensis promastigotes and intracellular amastigotes. Additionally, we tested the compound's efficacy in BALB/c mice infected with L. braziliensis via intraperitoneal administration to evaluate the reduction of lesion size and de-crease of parasite load in the ears and lymph nodes of infected animals. Results: 17-DMAG showed selective toxicity [selective index=432) towards Leishmania amastigotes, causing minimal damage to host cells. The treatment significantly reduced lesion sizes in mice and results in parasite clearance from ears and lymph nodes. It also diminished in-flammatory responses and reduced the release of pro-inflammatory cytokines (IL-6, IFN-g, TNF) and the regulatory cytokine, IL-10, underscoring its dual leishmanicidal and anti-inflammatory properties. Conclusion: Our findings confirm the potential of 17-DMAG as a viable treatment for cutaneous leishmaniasis and support further research into its mechanisms and potential applications against other infectious diseases.

Different polyurethanes (PUs) were synthesized with polycarbonate polyols of molecular weights 500, 1000 and 2000 Da. Their self-healing abilities at 20 °C were tested and their structural, thermal, and mechanical properties were analyzed. The PUs made with polycarbonates of molecular weights 500 (YC500) and 1000 Da (YC1000) exhibited self-healing at 20 °C and the self-healing time of YC1000 was the shortest. The high mobility of the short polymeric chains, the absence of crystallinity and the low degree of micro-phase separation favored self-healing at 20 °C in YC500. However, the presence of tack and the existence of allophanate species and urethane-carbonate and urea-carbonate hydrogen bonds disfavored self-healing. Consequently, the self-healing time at 20 °C of YC500 was longer than expected. On the other hand, YC1000 exhibited an “equilibrium” between the urethane-carbonate and urea-carbonate hydrogen bonds and carbonate-carbonate interactions among the soft segments, so a particular structural order was produced which was associated to its fastest self-healing at 20 °C. The PU made with the polycarbonate of molecular weight 2000 Da did not exhibit self-healing at 20 °C because its significant micro-phase separation and the presence of semi-crystalline soft domains.

Stage IV grade C localized periodontitis (pre-puberal localized aggressive periodontitis/LPP), an extremely rare form of periodontal disease, occurs in otherwise healthy individuals (no signs of dental plaque/calculus) due a hyper-aggressive auto-immune response to high periodontopathic bacteria levels. Methods: A 4-year-old Caucasian girl with unusual high mobility of temporary lower left canine and localized gingival inflammation was misrecognized by multiple clinicians (initially diagnosed with hypophosphatasia, genetic and metabolic disorders, all turning negative), over a period of 4-6 month, despite initial radiographs showing clear pathognomonic signs. LPP diagnostic was made by the last clinician, but by now the tooth was lost. Similar inflammation signs appeared around the lower temporary right canine. X-ray examination showed similar bone and periodontal loss as previously seen, while periodontopathic bacteria tested highly positive. The patient received both mechanical cleaning and ten days systemic antibiotic treatment (Augmentin and Metronidazole). Results: Two months after, inflammation signs disappeared, with periodontal regeneration radiologically present, and only small periodontopathic bacteria precursors concentrations. Conclusions: Despite initial periodontal loss, an adequate treatment can keep under control an LPP disease. Moreover, bone and periodontal regeneration appears if periodontopathic bacteria scores are kept lower, showing the importance of fast adequate diagnostic and treatment.

A series of dinuclear copper(I) N,C,N- and P,C,P-carbodiphosphorane (CDP) complexes using multidentate ligands CDP(Py)2 (1) and (CDP(CH2PPh2)2 (13) have been isolated and characterized. Detailed structural information was gained by single crystal XRD analyses of nine representative examples. The common structural motive is the central double ylidic carbon atom with its characteristic two lone-pairs involved into binding of two geminal L-Cu(I) fragments at Cu-Cu distances in the range 2.55 – 2.67 Å. In order to enhance conformational rigidity within the characteristic Cu-C-Cu triangle, two types of chelating side arms were symmetrically attached to each phosphorus atom: two 2-pyridyl functions in ligand CDP(Py)2 (1) and its dinuclear copper complexes 2-9 and 11, as well as two diphenylphosphinomethylene functions in ligand CDP(CH2PPh2)2 (13) and its di- and mononuclear complexes 14-18. Neutral complexes were typically obtained via reaction of 1 with Cu(I) species CuCl, CuI, and CuSPh or via salt elimination reaction of [(CuCl)2(CDP(Py)2] (2) with sodium carbazolate. Cationic Cu(I) complexes were prepared upon treating 1 with two equivalents of [Cu(NCMe)4]PF6, followed by the addition of either two equivalent of an aryl phosphine (PPh3, P(C6H4OMe)3) or one equivalent of a bisphosphine ligands DPEPhos, XantPhos or dppf. For the first time carbodiphosphorane CDP(CH2PPh2)2 (13) could be isolated upon treating its precursor [CH(dppm)2]Cl (12) with NaNH2 in liquid NH3. A protonated and a deprotonated derivative of ligand 13 were prepared and their coordination was compared to neutral CDP ligand 13. NMR analysis and DFT calculations reveal, that the most stable tautomer of 13 does not show a CDP (or carbone) structure in its uncoordinated base form. For most of the prepared complexes, photoluminescence upon irradiation with UV light at room temperature was observed. Quantum yields (PL) were determined to 36% for dicationic [(CuPPh3)2(CDP(Py)2)](PF6)2 (4) and to 60% for neutral [(CuSPh)2(CDP(CH2PPh2)2] (16).

In this paper, several two-dimensional clustering scenarios are given. In those scenarios, soft partitioning clustering algorithms (Fuzzy C-means (FCM) and Possibilistic c-means (PCM)) are applied. Afterward, VAT is used to investigate the clustering tendency visually, and then in order of checking cluster validation, three types of indices (e.g., PC, DI, and DBI) were used. After observing the clustering algorithms, it was evident that each of them has its limitations; however, PCM is more robust to noise than FCM as in case of FCM a noise point has to be considered as a member of any of the cluster.

The bulk planetary compositions are thought to be linked to the chemical abundances of their host stars. The abundances of 8 key rock-forming elements and the key planetary abundance ratios in G– and F–type main sequence stars located in the Solar neighborhood within 50 pc were statistically analyzed. The averaged C/O, Mg/Si, and Fe/Si elemental ratios of the planetary systems have a crucial role in the chemical composition and the mineralogy of a rocky planet's interior. We also studied the variation of the calculated Ca/Si, Al/Si, Na/Si and Fe/Si ratios in the samples of the examined stars using the Ca, Al, Na, and Fe abundances from the catalog and then attempt to constitute plausible occurrence trends of the analyzed abundance ratios for the rocky planet population in the near – solar galactocentric distances. Considering these results, we provide simple predictions for the most likely bulk compositions of the potential rocky planets. We further apply our results to compare them to the solar averaged abundance ratios, finding that the key elemental ratios for rocky planet composition in the Solar System are not typical amongst most of the studied stellar samples.

Solar pasteurization, as a means of treating milk in remote rural areas without electrical power, is based on using solar energy to thermally inactivate pathogenic microorganisms at temperatures below the boiling point to maintain or improve milk quality. A solar milk pasteurizer of flat‐plate water‐heating glass acting as the solar collector, connected to a stainless-steel cylindrical milk vat, was constructed and evaluated in Navrongo, in the tropical savanna zone of Ghana, West Africa. The novel approach taken in this project is to integrate the solar collection and heat exchanger into a single unit using materials and fabrication techniques readily available in the developing world. The vat comprises a 1.5 mm thick stainless steel cylindrical tank, a 2.2 cm wide hot water jacket, and an outer layer of 5.0 mm thick aluminium foil insulation. Hot water produced by the collector was used for pasteurizing milk. The optimum quantity of milk that this device could pasteurize under the study conditions was 8 L. The device could pasteurize raw milk to a maximum temperature of 74 °C at 14:00 h GMT. The ambient temperature during the pasteurization ranged from 30 °C to 43 °C. The microbial analysis before and after the pasteurization was done, and the result shows that the total bacteria count before pasteurization was 6.6x10⁶ log CFU/mL per unit volume, and the total bacteria count after pasteurization was 1.0x10² log CFU/mL. By acceptable standards, the total bacteria count after pasteurization is within a safe range for consumption, and coliform counts were negative. The solar milk pasteurization system is cost-effective. Hence, it is appropriate for milk producers in arid pastoral areas without electricity to adopt the solar pasteurizer as an alternative to firewood as a fuel source for milk pasteurization. This approach can potentially create a cottage industry that may also play a crucial role as a water treatment technology that will improve the health of rural populations.

Heart failure (HF) is a growing issue in developed countries and most patients present with a reduced ejection fraction. This condition significantly impairs quality of life and represents a threat not only for patients, but also for the entire healthcare system due to its high management cost. In the last decade, new medical treatments and devices have been developed to reduce HF hospitalizations and improve prognosis, while reducing the overall mortality rate. Medical therapy does not achieve the same results in all patients and, whenever it fails, technology comes in handy: novel devices for the management of HF have reduced symptoms. They have also improved the treatment of fluid retention and life threatening arrhythmias. The present review article gives to the readers a comprehensive overview of the most recent and important findings that need to be considered in HF with reduced ejection fraction patients. Both novel medical treatments and devices have been presented and discussed.

Abstract: Although the pathophysiology of fibromyalgia syndrome has been better understood in recent decades, a unified model of its pathogenesis and an effective therapeutic approach are still far from being realized. The main aim of this article will be to delve into the fundamental mechanisms of the pathophysiology of fibromyalgia conceptualized as stress intolerance syndrome. Using the biopsychosocial model of chronic pain syndromes, we will describe the potential role of the attachment system, C tactile fibers, and oxytocinergic system dysfunction in the pathophysiology of fibromyalgia syndrome and other central sensitivity syndromes. At the end of the article, the therapeutic implications of this new global and translational pathophysiological model will be briefly discussed.

Using a safe subset of C++ is a promising direction for increasing the safety of the programming language while maintaining its performance and productivity. In this paper, we examine how close existing C/C++ code is to conforming to a safe subset of C++. We examine the rules presented in existing safe C++ standards and safe C++ subsets. We analyze the code characteristics of 5.8 million code samples from the Exebench benchmark suite and 5 modern C++ applications using a static analysis tool. We find that raw pointers, unsafe casts, and unsafe library functions are used in both C++ code at large and modern C++ applications. In general, C++ code at large does not differ much from modern C++ code, and continued work will be required to transition from existing C/C++ code to a safe subset of C++.

This study investigates the synthesis and characterization of zirconium oxide (ZrO₂)-based metal-composites doped with cerium (Ce) and yttrium (Y), using chromium (Cr) and nickel (Ni) as base metals. These constituents were selected for their superior mechanical properties and compatibility with the ceramic phase. High-purity powders were homogenized via high-energy ball milling, followed by cold isostatic pressing (CIP) and sintering in a controlled atmosphere. The sintering process was conducted at various temperatures (850°C to 1350°C) to examine densification, grain growth, and microstructure evolution. Scanning Electron Microscopy (SEM) revealed a homogeneous distribution of phases, with distinct microstructural features attributed to each element at different sintering temperatures. Density measurements using the water immersion method and theoretical calculations demonstrated increased density and reduced porosity with higher sintering temperatures. Vickers hardness testing indicated that hardness improved with increased sintering temperature, peaking around 1150°C due to cerium and yttrium reinforcement within the matrix. Flexural strength tests showed the highest value at 1350°C, with a significant drop in porosity, suggesting enhanced mechanical properties due to efficient doping and phase transformations. Overall, the incorporation of cerium and yttrium significantly improved the mechanical behavior and phase stability of the ZrO₂-Cr-Ni composites, highlighting their potential for advanced engineering applications.

The neurodegenerative diseases (Alzheimers, Parkinsons, amyotrophic lateral sclerosis, Huntingdons) and the prion disorders, have in common a dysregulation of metalloprotein chemistry involving redox metals (Cu,Fe,Mn). The consequent oxidative stress gives rise to protein plaques and neuronal cell death. An equilibrium exists between the functional requirement of the brain for Cu and Fe and their destructive potential with the production of reactive oxygen species. The importance of the brain barrier is highlighted in regulating the import of these metals. Upregulation of key transporters occurs in foetal and neonatal life when brain metal requirement is high and is down-regulated in adult life when need is minimal. By contrast a neonatal mode of CTR1 upregulation persists in feral N.Ronaldsay sheep. This has led to the premise that metal regulation may return to the default setting in ageing with implications for neurodegenerative disease.

Background: Osteoporosis and bone fractures affect health and quality of life. Since bone disease is multifactorial, identifying risk factors is key in prevention. There are multiple reports on how viral hepatitis especially chronic hepatitis B (CHB) and chronic hepatitis C (CHC) are affecting bone disease, but results vary. Here, we analyzed the potential association between CHB/CHC and osteoporosis or bone fractures in a large outpatient cohort in Germany. Methods: We included 3,136 outpatients with CHB and 15,608 matched non-hepatitis individuals as well as 2,867 outpatients with CHC and 14,335 matched non-hepatitis individuals from the Disease Analyzer Database between 2005 and 2022. The main outcome was the 5-year cumulative incidence of osteoporosis and bone fractures as a function of either CHB or CHC. Results: Within 5 years of the index date, 2.9% vs. 1.6% of patients with and without CHB were diagnosed with osteoporosis (p=0.001) and 1.0% vs. 0.4% were diagnosed with bone fractures (p<0.001). Moreover, 3.3% of CHC patients and 2.2% of individuals without hepatitis were diagnosed with osteoporosis (p=0.002). In Cox-regression analyses, CHB was significantly associated with an increased risk for osteoporosis (HR: 1.76) and fractures (HR:2.43) and CHC with osteoporosis (HR: 1.54). For both CHB and CHC, the association with osteoporosis was restricted to the female subgroup. Conclusion: CHB and CHC are associated with osteoporosis in women. CHB in male patients is associated with a higher risk of fractures. More research is are needed to understand the underlying pathophysiological mechanisms.