In the case of a Cu-Mo-W polymetallic ore, the wastewater from the scheelite cleaning flowsheet contains large amounts of residual flocculants and metal ions, and the separation of chalcopyrite and molybdenite require a large number of environmentally harmful depressants. Therefore, it is necessary to find new methods to reduce the environmental and cost pressures of wastewater treatment and the use of depressants. In this work, the flotation wastewater from scheelite cleaning flowsheet for the separation of chalcopyrite and molybdenite by selective surface passivation was investigated for the first time. Flotations of single minerals and artificially mixed minerals with or without immersion pretreatment in the presence and absence of aeration were performed. The results showed that pulp pH had no effect on the flotation of either mineral, and a molybdenite recovery of 93.22% with chalcopyrite recovery of 10.77% was achieved under the conditions of 10 days of immersion pretreatment with aeration, 350 mg/L of kerosene, and 100 mg/L of MIBC. By combining the electrochemical cyclic voltammetry analysis and characterization by XRD and SEM, the selective surface passivation mechanism of chalcopyrite was discussed, which could be due to the coverage of the insoluble oxidation products, especially jarosite. This work has simultaneously achieved the depressant-free flotation separation of molybdenite and chalcopyrite and the reuse of scheelite flotation wastewater, which is of great significance for environmental protection and cost saving.

Bioprocesses for the production of renewable energies and materials lack efficient separation processes for the utilized microorganisms such as algae and yeasts. Dissolved air flotation (DAF) and microflotation are promising approaches to overcome this problem. The efficiency of these processes depends on the ability of microorganisms to aggregate with microbubbles in the flotation tank. In this study, different new or adapted aggregation models for microbubbles and microorganisms are compared and investigated for their range of suitability to predict the separation efficiency of microorganisms from fermentation broths. The complexity of the heteroaggregation models range from an algebraic model to a 2D population balance model (PBM) including the formation of clusters containing several bubbles and microorganisms. The effect of bubble and cell size distributions on the flotation efficiency is considered by applying PBMs, as well. To determine the impact of the model assumptions, the modeling approaches are compared and classified for their range of applicability. Evaluating computational fluid dynamics (CFD) of a DAF system shows the heterogeneity of the fluid dynamics in the flotation tank. Since analysis of the streamlines of the tank show negligible backmixing, the proposed aggregation models are coupled to the CFD data by applying a Lagrangian approach.

Plastics are naturally hydrophobic materials so, in order to employ flotation for the separation of plastic mixtures, the use of appropriate wetting agents is mandatory. In this work, the effect of pretreatment with alkaline solutions of sodium hydroxide on the floatability of four plastics (PET, PS, PMMA and PVC) was studied. The influence of NaOH concentration, treatment time and temperature of the alkaline solution, and influence of particle size was analyzed. Results showed that alkaline treatment had a strong effect on PET floatability, some effect on floatability of PMMA and PVC and no effect on floatability of PS. Plastics floatability decreased with the increase of NaOH concentration, temperature and treatment time of the alkaline solution. Based on flotation behavior of simple plastics, flotation separation after alkaline treatment of bi-component mixtures of PET with PS and PVC was achieved efficiently. The best separation was obtained for PET/PS mixture, a floated with a grade of 98% in PS and a sunk with a grade of 100% in PET. PET/PMMA mixture led to the worst separation. For PET/PMMA and PET/PVC mixtures, flotation separation improved with the decrease of the particles size.

Lactoperoxidase (LP), which is a high-value minor whey protein, has recently drawn extensive attention from research scientists and industry due to its multi-function and potential therapeutic applications. In this study, the separation and optimization of two similar-sized proteins, LP and lactoferrin (LF) were investigated using strong cation exchange column chromatography. Optimization was started with central composite design based experiments to characterize the importance of different decision variables. The three variables used in the optimization were flow rate, length of gradient and final salt concentration in the linear elution gradient step. The obtained empiric functional model represented the effect of the significant factors on the yield as the objective function. Afterwards, the calibrated mechanistic model was employed to predict accurate optimal set of variables. The optimal operating points were found and the results were compared with validation experiments. Predictions respecting yield confirmed a very good agreement with experimental results while keeping purity, a product quality characteristic, equal or above to a predefined value.

Dye/salt separation has gained increasing attention in recent years, prompting the quest for cost-effective and environmentally-friendly raw materials for synthesis high performance nanofiltration (NF) membrane for effective dye/salt separation. Herein, a high-performance loose structured NF membrane was fabricated by via a simple vacuum filtration method using a green nanomaterial, 2,2,6,6-tetramethylpiperidine-1-oxide radical (TEMPO)-oxidized cellulose nanofiber (TOCNF), by sequentially filtrating larger-size and finer-size TOCNFs on a microporous substrate, followed by cross-linked with trimesoyl chloride. The resultant TCM membrane possesses a separating layer composed entirely of pure TOCNF, eliminating the need for other polymer or nanomaterials additives. TCM membranes exhibits high performance and effective dye/salt selectivity. Scanning Electron Microscope (SEM) analysis shows that the TCM membrane with Fine-TOCNF layer has a tight layered structure. Further characterizations via Fourier transform infrared spectroscopy (FTIR) and X-ray diffraction (XRD) confirm the presence of functional groups and chemical bonds of the crosslinked membrane. Notably, the optimized TCM-5 membrane exhibits a rejection rate of over 99% for various dyes (Congo red, orange yellow) and 14.2% for NaCl, showcasing a potential candidate for efficient dye wastewater treatment.

This article presents research on selected materials with the aim of determining their rare earth element (REE) content and attempting to intensify it. The test material was coal slurry, which is a waste product from the operation of a preparation plant of a closed coal mine. Research on REE concentration intensification tests was carried out using magnetic separation. Laboratory analyses determining the REE content in the samples obtained, were carried out using the inductively coupled plasma ionisation mass spectrometry (ICP-MS) technique. Carrying out this research by the KOMAG Institute of Mining Technology, is a continuation of work related to making mining waste economically useful and determining a new source of REE recovery. Previous research and development work showed REE content (scandium 40.49 ppm) in the coal slurries studied. The result of the work carried out is the determination of the economic utility of REE recovery from the studied waste.

Abstract: Toxicity of emerging organic pollutants to photosystems of aquatic plants are still not well clarified. This study aimed to develop a novel ecotoxicological experimental protocol based on nanoscale electrochemical mapping of photosynthetic oxygen evolution of aquatic plants by SECM (scanning electrochemical microscopy). The protocol was also checked by confocal laser scanning microscopy (CLSM), the traditional Clark oxygen electrode method and chlorophyll fluorescence technique. The typical persistent organic pollutant 2,4-dichlorophenol (2,4-DCP) in water environment and the common aquatic Microsorium pteropus (M. pteropus) were chosen as the model organic pollutant and tested plant, respectively. It was found that the SECM method could well discriminated the responses of stoma micromorphology and spatial pattens of photosynthetic oxygen evolution on single stoma. The shape of stoma blurred with increasing 2,4-DCP concentration, which was in good agreement with the CLSM images. The dose-response curves and IC50 values obtained from the SECM data were verified by the data measured by the traditional Clark oxygen electrode method and chlorophyll fluorescence test. The IC50 value of single stoma oxygen emission of 24 h exposed plant leave, which was derived from the SECM current data (32535 μg L-1), was close to those calculated from the maximum photosynthetic efficiency (Fv/Fm) measured by chlorophyll fluorescence test (33963 μg L-1), and the Clark oxygen electrode method photosynthetic oxygen evolution rate (32375 μg L-1). The 72 h and 96 h 2,4-DCP exposure data further confirmed the reliability of the nanoscale stoma oxygen emission mapping methodology for ecotoxicological assessment. In this protocol, the procedures for how to collect effective electrochemical data and how to extract useful information from the single stoma oxygen emission pattern were well established. This study showed that SECM is a feasible and reliable ecotoxicological tool for evaluation of toxicity of organic pollutants to higher plants with unique nanoscale visualization advantage over the conventional methods.

Phosphorus is essential and non-substitutable chemical element required for the cellular processes of all living organisms. The main source of phosphorus in the biosphere is phosphate rock. With more than 700 Mt P2O5, Estonia holds the largest sedimentary phosphate rock deposits in European Union. Estonian phosphate rock is principally sandstone that holds abundant remains of phosphatic brachiopod shells and compared to other sedimentary rocks, is particularly outstanding by its remarkably low content of hazardous heavy metals such as Cd and saturated by valuable elements present in the rock such as rear earth elements (REEs).

: Flotation performance in plants can significantly be affected by seasonal variations in different parts of the world. This is generally attributed to the changes in water temperature and pulp temperature in flotation plants, type and concentration of dissolved ions in process water. Extreme temperature conditions may be the major factor affecting flotation performance and mask the influence of water chemistry. Therefore, the interactive effects of the temperature and water chemistry should be taken into consideration, particularly for mine sites experiencing extreme temperature conditions. In this paper, effects of temperature, sulphate (SO42-), thiosulphate (S2O32-) and calcium (Ca2+) ions on the flotation performance of a Cu-Pb-Zn complex sulfide ore were investigated using a statistical experimental design and modelling approach. Batch scale kinetic flotation tests were conducted using the sequential flotation flowsheet of a bulk Cu-Pb flotation stage followed by a zinc rougher flotation stage. The results of the zinc flotation section were used for the statistical evaluation since the zinc concentrate was the product with an economic value for the mine. The results were evaluated using ANOVA analysis and regression analysis to determine the significant parameters and derive individual regression models for each flotation response with Design Expert software version 6.0.8. Individual regression models were developed using the significant main effects and their interactions for each flotation response. Then, the models were used to determine the concentration of the dissolved ions and pulp temperature required to achieve the maximum zinc recovery, maximum zinc grade or the optimum zinc grade and recovery. The details of statistical experimental design, discussions on the effects of the experimental factors and their interactions on the flotation performance and development of regression models are discussed in this paper.

Temperature-responsive separation membranes can significantly change their permeability and separation properties in response to changes in their surrounding temperature, improving efficiency and reducing membrane costs. This study focuses on the modification of commercial polyvinylidene fluoride (PVDF) membranes with amphiphilic temperature-responsive copolymer and inorganic nanoparticles. We prepared an amphiphilic temperature-responsive copolymer which the hydrophilic poly(N-isopropyl acrylamide) (PNIPAAm) was side-linked to a hydrophobic polyvinylidene fluoride (PVDF) skeleton. Subsequently, PVDF-g-NIPAAm polymer and graphene oxide (GO) blended with PVDF to prepare temperature-responsive separation membranes. The results showed that temperature-responsive polymers with different NIPAAm grafting ratios were successfully prepared by adjusting the material ratio of PVDF to NIPAAm. PVDF-g-NIPAAm was blended with PVDF with different grafting ratios to obtain separate membranes with different temperature responses. GO and PVDF-g-NIPAAm formed a relatively stable hydrogen bond network, which improved the internal structure and mechanical properties of the membrane without affecting the temperature response, thus extending the service life of the membrane.

Diethyldithiocarbamate (DDTC) has been employed in the sulfide ore flotation process, due to its excellent collection performance. Herein, we investigated the interfacial adsorption behavior of DDTC on four mineral phases of high-sulfur residue — sulfur, pyrite, sphalerite and lead sulfate. The adsorption behavior — adsorption structure and energy and electron localization function cross section — of DDTC and H2O were explored using density function theory calculation. The result was helpful to construct a co-adsorption model of DDTC and H2O, which was validated by the pure minerals flotation operation and the characterization of fourier transform infrared spectra. The co-adsorption model indicated that the DDTC adsorption on the sulfur, sphalerite and lead sulfate was weak with physical bonding, while its adsorption on the pyrite was strong with chemical bonding. Practical bench-scale operation of high-sulfur residue flotation was performed, whose result was different from that obtained from the pure mineral flotation. To explain the difference, our developed model predictions and the mineral fugacity pattern analysis on the high-sulfur residue flotation were synergistically used. Overall, this work first proposed the co-adsorption model of DDTC and H2O and provided important insights into the interfacial adsorption in the high-sulfur residue flotation.

To overcome the difficulty of separating bastnaesite from fluorite through the flota-tion technique, the present study examined the suitability of sodium alginate (SA) as a depressant in the flotation process. The effect of SA on the flotation separation of bastnaesite and fluorite was evaluated using micro-flotation tests, zeta potential meas-urements, adsorption density measurements, Fourier infrared spectroscopy, and X-ray photoelectron spectroscopy. The micro-flotation results showed that SA exerted a strongly detrimental effect on fluorite flotation, while slightly affecting bastnaesite flotation. The surface chemistry results revealed that the -COO- and HO- functional groups in SA coordinated with Ca2+ on the fluorite surface, which induced hydro-philicity and hindered the adsorption in the subsequent collector. However, the inter-action of SA with the bastnaesite surface was marginal and did not affect the anchor-ing of the collector on the surface of bastnaesite. Based on these results, the present study proposes a possible model for the interaction of SA on the surfaces of the two minerals, laying a foundation for the flotation separation of bastnaesite from fluorite with SA as an environmentally benign depressant.

Vibro-fluidized dry coal beneficiation involves the unavoidable mixing of -1 mm coal dust into the fluidized bed, which compromises the stability and homogeneity of the bed density and reduces the effectiveness of fine-grained coal separation. In order to understand the features of coal powder separation and mixing (-1 mm) in a vibrating fluidized bed, as well as to achieve a uniform and stable bed density, a wide-grained dense medium consisting of -1 mm coal dust and 0.3-0.15 mm magnetite powder was homogeneously mixed in this work. The degree of density separation in the entire bed was examined, as well as the local mixing properties of the Wide-grained Dense Medium. It was discovered that when low vibrational energy was introduced at the same gas velocity, particle separation was enhanced in comparison to the usual fluidized bed. Little bubbles were found to ensnare fine coal dust and migrate upward, increasing density separation. The introduction of high vibrational energy leads to particle disorder within the bed and an increase in the level of particle mixing. The beneficial effects of vibration on the bed are diminished when the gas velocity is gradually increased under specified vibration circumstances. This causes big bubbles to develop more frequently, which increases particle mixing. Among them, the 1-0.5 mm fine-grained coal exhibits the best mixing state; it is less impacted by variations in air velocity and vibration levels, whereas the -0.5 mm coal dust is more affected by each of these variables. Furthermore, a wide range of air velocity regulation without a significant segregation state change was discovered to be achievable by the particle system under vibration circumstances of f=25Hz A=1mm and f=25Hz A=2mm.

Delipidation is a method of defatting that is generally associated with the removal of residual lipids or lipid groups from matrices in which they are present in minute quantities. The bio-delipidation of protein-rich poultry slaughterhouse wastewater (PSW) pre-treated with a dissolved air flotation (DAF) system was developed using microbial lipases from bacterial strains isolated from the PSW. The efficacy of the bio-delipidation system was quantitatively characterised by comparing the quality parameters i.e., fats, oil and grease (FOGs), turbidity, total suspended solutes (TSS), total chemical oxygen demand (tCOD) and protein concentration of the DAF pre-treated PSW and bio-lipidized samples. As hypothesised, the bio-delipidation system was able to effectively reduce the levels of these quality parameters when crude lipases of Bacillus cereus AB1 (BF3) and Bacillus cereus CC-1 (B30) strains were used. Strain-dependent quality characteristics were also observed in bio-delipidized samples. The study successfully managed to complement physical reduction techniques (DAF) with biological strategies (bio-delipidation) for improved PSW quality, with potential industrial applications.

As hematite ores become lower in grade, finer in grain size, and more complex in compositions, their beneficiation by froth flotation to produce the high Fe grade concentrate has become increasingly more difficult. A systematic and in-depth process mineralogy study based on the multi-element chemical and MLA analysis combined with other characterization techniques was conducted to explore the fundamental reasons for difficulties in refractory hematite flotation separation. The results show that the valuable mineral in the sample was mainly hematite and gangue mineral was primarily quartz. Hematite had a fine particle size distributed over a range of 0~45 μm with a degree of mineral liberation of 90.19%. The particle size of quartz was relatively coarse and was mainly distributed in the range of 20~150 μm with a liberation degree of only 67.72%. Unliberated quartz was mainly associated with hematite and the composite particle content was 36.44%. The rougher flotation tests produced a flotation concentrate of 66.71% TFe grade at a recovery of 65.47%. The screening analysis results with rougher flotation products indicated that the main reasons for the poor performance of rougher flotation were the serious entrainment of fine hematite particles and the difficulty in effective collection of coarse low-grade composite particles. Possible approaches for improving hematite flotation performance have been proposed based on the results from this study.

Separation Distances are used throughout the world to protect people and assets from the potential hazardous effects from propellants, explosives, and pyrotechnics. The current separation distances for Hazard Division (HD) 1.3 substances and articles used in the United States, in some cases, may not adequately protect against the effects from heat flux and debris when those substances and articles are ignited in a confined structure. Multiple tests in such a confined scenario with HD 1.3 substances have shown that the heat flux and debris hazards could result in injury at distances beyond the current specified explosives safety separation distance (ESSD). Herein are recommended ESSD’s for confined as well as unconfined HD 1.3 articles and substances based on the analysis of hundreds of tests. Recommended ESSD’s include a smaller value for unconfined quantities less than 145 kilograms and ESSD’s that are consistent with NATO distances for confined substances and articles.

Minerals are the chief constituents of rocks and they have varied properties such as surface area, surface charge, site densities etc. Hence, numerous interactions are bound to occur in the reservoir during rock-fluids (i.e., rock, crude oil and brine) interactions. This study seeks to assess the role of mineralogical composition on the wettability of Sandstone Rocks (SR) and Mineral Mixture (MM) using both Surface Complexation Modelling (SCM) and flotation test. From the considered sandstone rocks, both the experimental results and its simulated counterpart revealed that, the SR were preferentially hydrophilic. For the MM, when the mass fraction of the hydrophobic mineral was increased, the affinity of the MM became slightly hydrophobic and vice-versa. For the dominant sandstone reservoir rock minerals with predominantly negatively charged surfaces, negligible oil adsorption took place due the interfacial repulsive forces at the oil-brine and mineral-brine interfaces. For the MM with low calcite content, the wetting preference was influenced by the mineral with prominent surface area. Our developed model portrayed that the main mechanism for oil adhesion onto sandstone minerals was divalent cations bridging. Nonetheless, adhesion of carboxylate (>COO-) onto the illite, montmorillonite and calcite sites also took place with the latter being more pronounced.

Mining and processing tailings often contain significant amounts of valuable metals, that can represent valuable sources of secondary raw materials. Especially this is case in early-stage operations, in which the head grades were higher, and the tailings were higher grade. These tailings can also present a substantial risk to the environment. Serbia has copper deposits which have been exploited since ancient times, and these operations have generated large amounts of mineral processing tailings. The main objective of this study is to show how valuables can be recovered from chemically and mineralogically challenging tailings. After detailed chemical and mineralogical characterization, the laboratory scale flotation tests focused on evaluating the effect of particle size, different types of collectors, pH, and pulp potential. Based on the test work, copper and gold can be recovered effectively into pyrite concentrate

Zinc is mostly extracted from zinc oxide and sulfide minerals, and this process involves flotation as a key step. While it is easier to float the sulfide mineral, its consumption and depletion has led to an increased reliance on zinc oxide minerals, including smithsonite; hence the development of efficient ways of collecting smithsonite by flotation is an important objective. Herein, we describe the use of 2-(hexadecanoylamino)acetic acid (HAA), a novel surfactant, as a collector during smithsonite flotation. The mechanism and flotation performance of HAA during smithsonite flotation were investigated by total organic carbon (TOC) content studies, zeta potential measurements, FTIR spectroscopy, and XPS analyses, combined with micro-flotation experiments. The flotation results revealed that HAA is an excellent collector in pulp over a wide pH range (9–12) and at a relatively low concentration (2 × 10^‒4 mol/L), at which a recovery of close to 90% of the smithsonite mineral was obtained. TOC-content studies reveal that the good flotation recovery is ascribable to large amounts of collector molecule adsorbed on the smithsonite surface, while zeta potential measurements show that the HAA is chemically adsorbed onto the smithsonite. FTIR and XPS analyses reveal that the HAA-collector molecules adsorb onto the smithsonite surface as zinc-HAA complexes involving carboxylate moieties and Zn sites on the smithsonite surface in alkaline solution.

The mechanism of anionic/cationic combination collector ST-8 for the efficient separation of spodumene and feldspar was investigated by flotation tests, surface tension measurements, zeta potential measurements and infrared spectroscopy analysis. The flotation results indicated that when the optimum molar combination of sodium oleate and dodecylamine was 6:1-10:1 and pH=8.5 or so, the recovery of spodumene reached a maximum of 80% and that of feldspar reached about 24.5%. Zeta potential measurements showed that the negative shift of the kinetic potential on the surface of spodumene was much stronger than that on the surface of feldspar, indicating that the adsorption capacity of the combined collector on spodumene surface and feldspar surface was greatly different. From the surface tension as well as the synergistic parameters, there was a strong mutual attraction between dodecylamine and sodium oleate, and there was a significant synergistic effect between them. Infrared spectroscopy indicated that the combined collector chemisorbed on the mineral surface, and the intensity of the absorption peak after the action of spodumene was much stronger than that after the action of feldspar. The solution chemistry of the combined collector revealed that at pH 8.5, the positively charged ions RNH3+ and (RNH3+)22+ in dodecylamine and the negatively charged RCOO- and (RCOO-)22- ions in oleic acid form highly reactive complexes to interact with the mineral surface by electrostatic gravitation, thus achieving efficient separation of spodumene and feldspar. Finally, from the closed circuit test results, a flotation index of 6.34% Li2O grade and 88.51% Li2O recovery was obtained.

Annotation. The experience of using coal flotation waste (CFW) as a weakly exothermic insulating backfill for insulating the head part of forging dead-melted steel ingots is presented.It has been shown that when using weakly exothermic fills based on single-component fills in the form of CFW, it is possible to reduce the chemical heterogeneity of the ingot by producing a closed shrinkage cavity, which allows halving heat loss and depth of penetration of shrinkage looseness into the body of the ingot, reducing the segregation of impurities, compacting the head part of the ingot and increasing the yield; moreover, the profitable part of the ingot is more dense and less contaminated with nonmetallic inclusions.The studied patterns of the formation of a closed shrinkage cavity with a dense “bridge” in the head part of a dead-melted steel ingot made it possible to develop and implement a technology for casting large forging ingots of sufficiently high quality using weakly exothermic heat-insulating materials based on metallurgical waste (coke screenings, coal flotation waste)

When describing the tribological behaviour of technical surfaces, the need for full length scale microtopographic characterization often arises. The self-affine of surfaces and the characterization of self-affine by a fractal dimension and its implantation into tribological models are commonly used. The goal of our present work was to determine the frequency range of fractal behaviour of surfaces by analysing the microtopographic measurements of a brake plunger. We also wanted to know if the bifractal and multifractal behaviour can be detected in real machine parts. As a result, we developed a new methodology for determining the fractal range boundaries to separate the nano- and micro-roughness. In order to reach our goals, we used atomic force microscope (AFM) and stylus instrument to provide measurements in wide frequency range (19 nm - 3 mm). As a result of the power spectral density (PSD) based fractal evaluation, it was found that the examined surface could not be characterized by a single fractal dimension and that we developed a methodology for stopping the margin of validity of each fractal dimension, and we also developed a methodology for determining the limits of validity of certain fractal dimensions.

The combination of neural network and beamforming has been proved to be very effective in multi-channel speech separation. But its performance faces a challenge in complex environment. In this paper, an iteratively refined multi-channel speech separation method is proposed for the challenge, where the proposed is composed of initial separation and iterative separation. In initial separation, the time-frequency domain dual-path recurrent neural network neural network (TFDPRNN), minimum variance distortionless response (MVDR) beamformer and post-separation (also TFDPRNN) are cascaded for obtaining the first additional input in iterative separation. In iterative separation, the MVDR beamformer and post-separation are iteratively used, where the output of the MVDR beamformer is used as an additional input of the post-separation network and the final output comes from post-separation module. This iteration of the beamformer and post-separation is fully employed for promoting their individual optimization, which ultimately improves the overall performance of speech separation in multi-speaker scenarios. Experiments on the spatialized version of the WSJ0-2mix corpus show that our proposed method is significantly better than the current popular methods. In addition, the method also has a good effect on the dereverberation task.

Motivated by the PEACOC project on metal recovery from solid wastes, an innovative magnetic density separation (MDS) process has been developed for granular material sorting. It has intrinsic advantages over the existing industrialized MDS by eliminating fluid turbulence and particle jamming problems. The new MDS applies an inclined planar magnet and a horizontal basin containing a static magnetic fluid as the separation medium. A particle sliding phenomenon is identified as a feature of the process which could help the separation. The MDS successfully sorted shredded PCBAs to concentrate valuable metals and sorted shredded wires to reduce metallic contaminants in the plastic fractions. A pilot scale facility is introduced to show the design to achieve continuous production and to reduce the consumption of ferrofluid.

Several specific types of ordinary and generalized separation axioms of a generalized topological space have been defined and investigated for various purposes from time to time in the literature of topological spaces. Our recent research in the field of a new class of generalized separation axioms of a generalized topological space is reported herein as a starting point for more generalized classes.

Involving industrial waste into economic circulation, in particular flotation waste from coal enrichment, is an urgent task. The coal preparation waste of ArcelorMittal Temirtau JSC was studied with a view to the possibility of using it as an alternative substitute for coke breeze in the sintering process. During a thermoanalytical study on a synchronous thermal analyzer STA 449 NETZSCH in dynamic mode with a heating rate of 10, 20, 30 °C/min in an air flow of 30 cm³/min in the temperature range 30–1000 °C, we determined the lower heat of combustion of carbon-containing material, change mass during calcination, change and rate of change in the mass of the sample, thermal effect of the process, the temperature of the beginning, end and maximum development of thermal effects. It has been established that the greatest mass loss is observed in the temperature range 580 °C- 610 °C, which is about 65–67% of the total mass of the organic component of coal. The maximum burnout rate corresponds to a temperature of 540–563 °C. The lowest calorific value of the studied waste was 15.9 MJ/kg. The results of thermal analytical research and technical analysis substantiate the possibility of using flotation waste in a mixture of up to 10% with coke breeze for combustion in the sintering layer for the production of sinter. Analysis of the composition of flotation waste showed that they have a high specific surface area (56.8∙10³ m²/kg), are highly dispersible, soggy, and capable of swelling, and the predominant amount of clay substance makes them a plastic material. The possibilities of using coal flotation waste as an alternative substitute for coke breeze have been studied after the regimes of its preparation for sintering have been developed and a rational regime of layer-by-layer combustion in the sintering layer has been established. The optimal ratio of coke and OPC in the fuel mixture of the sintering charge was determined.

We aimed to investigate the relationship between membrane material and development of membrane fouling in a membrane bioreactor (MBR) using membranes with different pore sizes and hydrophilicities. Batch filtration tests were performed using submerged single hollow fiber membrane ultrafiltration (UF) modules with different polymeric membrane materials including cellulose acetate (CA), polyethersulfone (PES), and polyvinylidene fluoride (PVDF) with activated sludge taken from a municipal wastewater treatment plant. The three UF hollow fiber membranes were prepared by a non-solvent-induced phase separation method and had similar water permeabilities and pore sizes. The results revealed that transmembrane pressure (TMP) increased more sharply for the hydrophobic PVDF membrane than for the hydrophilic CA membrane in batch filtration tests, even when membranes with similar permeabilities and pore sizes were used. PVDF hollow fiber membranes with smaller pores had greater fouling propensity than those with larger pores. In contrast, CA hollow fiber membranes showed good mitigation of membrane fouling regardless of pore size. The results obtained in this study suggest that the surface hydrophilicity and pore size of UF membranes clearly affect the fouling properties in MBR operation when using activated sludge.

Membranes are a selective barrier that allows certain species (molecules and ions) to pass through while blocking others. Some rely on size exclusion, where larger molecules get stuck while smaller ones permeate through. Others use differences in charge or polarity to attract and repel specific species. Membranes can be used to purify air and water by allowing only air and water molecules to pass through but preventing contaminants such as microorganisms and particles or to separate target gas or vapor, such as H2, CO₂, from other gases. The higher the flux and selectivity, the better a material is for membranes. The desirable performance can be tuned through material type (polymers, ceramics, and biobased materials), microstructure (porosity and tortuosity), and surface chemistry. Most membranes are made from plastic from petroleum-based resources, which contribute to global climate change and plastic pollution. Cellulose can be an alternative sustainable resource to make renewable membranes. Cellulose exists in plant cell walls as natural fibers, which can be broken down into smaller components such as cellulose fibrils, nanofibrils, nanocrystals, and cellulose macromolecules through mechanical and chemical processing. Membranes made from reassembling these particles and molecules have variable pore architecture, porosity, and separation properties and therefore have a wide range of applications in nano-, micro-, and ultrafiltration or forward osmosis. Despite their advantages, cellulose membranes face some challenges. Improving the selectivity of membranes for specific molecules often comes at the expense of permeability. The stability of cellulose membranes in harsh environments or under continuous operation needs further improvement. Research is ongoing to address these challenges and develop advanced cellulose membranes with enhanced performance. This article reviews the microstructure, fabrication methods, and potential applications of cellulose membranes, providing some critical insights into processing-structure-property relationships for current state-of-the-art cellulosic membranes that could be used to rationally improve their performance.

These years have witnessed growing research on applying rheology in grinding and flotation treatment of finely disseminated ores. The slurry rheology has long been identified as the comprehensive effect of inter-particle interactions, including their aggregation (coagulation and flocculation) and dispersion states in slurry, which are more impactive under the fine-particle effect. In this regard, rheology has the potential to play a significant role in interpreting the flowing and deforming phenomenon of inter-particle aggregates, particle-bubble aggregates, and flotation froth. Though much attention has been paid to the rheological effect in industrial suspension, this has not been the case for mineral grinding and flotation for fine particles. The influential mechanism of rheology on the sub-processes of mineral processing has not been systemically concluded and revealed thoroughly, without which the underpinning mechanism for enhancing the processing efficiency has been difficult to discover. This paper reviews the current application and importance of rheology in the fine mineral processing, and the potential research direction in the field is proposed.

Depletion of ore deposits, increasing demand for raw materials, the need to process low-grade, complex and finely disseminated ores and the reprocessing of tailings are challenges, especially for froth flotation separation technologies. Even though capable of handling relatively fine grain sizes the flotation separation of very fine and ultrafine particles faces many problems still. Further, the flotation of low-contrast semi-soluble salt-type minerals with very similar surface properties, many complex interactions between minerals, reagents and dissolved species often result in poor selectivity. This study investigates the flotation beneficiation of ultrafine magnesite rich in dolomite from de-sliming, currently reported to the tailings. The paper especially focuses on the impact of the depressant sodium hexametaphosphate (SHMP) on: (i) the froth properties using dynamic froth analysis (DFA), (ii) the separation between magnesite and dolomite/calcite and (iii) its effect on the entrainment. Furthermore, the application of 1-hydroxyethylene-1,1-diphosphonic acid (HEDP) is a more environmentally friendly and low-cost alternative to SHMP is presented and discussed. The paper contributes to understanding on the complexity of depressant responses in froth flotation.

The recent Planck Legacy release confirmed the existence of an enhanced lensing amplitude in the cosmic microwave background (CMB) power spectra, which endorses the positive curvature of the early Universe with a confidence level exceeding 99%. In this study, the pre-existing curvature is incorporated to extend the field equations where the derived wave function of the Universe is utilized to model Universe evolution with reference to the scale factor of the early Universe and its radius of curvature upon the emission of the CMB. The wave function reveals both positive and negative solutions, implying that matter and antimatter of early Universe plasma evolve in opposite directions as distinct Universe sides. The wave function indicates that a nascent hyperbolic expansion is followed by a first phase of decelerating expansion away from early plasma during the first 10 Gyr, and then, a second phase of accelerating expansion in reverse directions, whereby both Universe sides free-fall towards each other under gravitational acceleration. Simulations of the predicted conformal curvature evolution demonstrate the fast orbital speed of outer stars owing to the external fields exerted on galaxies as they travel through conformally curved space-time. Finally, the wave function predicts an eventual time-reversal phase comprising rapid spatial contraction that culminates in a Big Crunch, signalling a cyclic Universe. These findings reveal that early plasma could have separated and evolved into distinct sides that collectively and geometrically influencing the Universe evolution, physically explanting the effects attributed to dark matter and energy.

The term “conservation,” as it relates to biodiversity in a Western context, has a storied past and as conservation science and societal values have evolved, consensus over its precise meaning has remained elusive. The broad scope of contemporary definitions hampers effective communication during a period of environmental crisis and is troublesome for any derivative concept which aims to empirically quantify the efforts of the conservation sector. This presents an avoidable hindrance to the systematic planning of the conservation field. To help remedy this situation, we provide an outcome separation framework that is based on the expected degree of separation between an action’s proximate outcome, from its intended, ultimate outcome for a habitat and/or species. Framing a definition of conservation through this lens of outcome separation allows for conservation-related actions to be clearly categorized into one of three discrete tiers: primary, secondary, and tertiary. A distillation of this tiered framework also provides a new definition of biodiversity conservation that is more rigorous and adaptable to future conceptual evolutions of the field.

Chromatographic separation is a critical technique in the manufacturing processes of both chemical products and biopharmaceuticals. Its principle relies on exploiting the differences in distribution between the stationary and mobile phases to achieve the separation of mixtures. The precision of substance concentration during separation directly impacts the quality and usability of the final product. Therefore, the development of an effective and precise separation control technique has long been a vital concern in the field of chromatographic separation control. Currently, the employment of Simulated Moving Bed (SMB) technology for chromatographic separation, which allows for continuous feed, has been recognized as a cutting-edge technique. SMB is a continuous process technology that enhances the efficiency of adsorbents within the bed. This sequential multi-column SMB technology not only increases production capacity but also reduces the consumption of solvents and water. It is acknowledged as one of the cleanest manufacturing technologies in the biopharmaceutical industry. However, multi-column SMB involves various variables such as flow rates in multiple sections and valve switching times, rendering its system control highly complex. Unlike traditional control objectives that aim to minimize control output errors, the control objective of SMB is to achieve a specific proportion of substance concentration. Consequently, designing and implementing traditional control theories for SMB is challenging, leading to SMB systems largely being controlled based on simple PLC controls. Moreover, these controls are often applicable only to single or a few-column SMB setups, limiting the effectiveness of high-capacity applications. To achieve effective control of SMB, this study employs an adjustable intelligent fuzzy controller with a structure like an approximate neural network (NN) for SMB control research. Simulation results demonstrate that the intelligent controller effectively achieves desirable control outcomes for the SMB system.

Separation and detection of cells and particles in a suspension are essential for various applications, including biomedical investigations and clinical diagnostics. Microfluidics realizes the miniaturization of analytical devices by controlling the motion of a small volume of fluids in microchannels and microchambers. Accordingly, microfluidic devices have been widely used in particle/ cell manipulation processes. Different microfluidic methods for particle separation include dielectrophoretic, magnetic, optical, acoustic, hydrodynamic, and chemical techniques. Dielectrophoresis (DEP) is a method for manipulating polarizable particles’ trajectories in non-uniform electric fields using unique dielectric characteristics. It provides several advantages for dealing with neutral bioparticles owing to its sensitivity, selectivity, and noninvasive nature. This review provides a detailed study on the signal-based DEP methods that use the applied signal parameters, including frequency, amplitude, phase, and shape for cell/particle separation and manipulation. Rather than employing complex channels or time-consuming fabrication procedures, these methods realize sorting and detecting the cells/particles by modifying the signal parameters while using a simple device. In addition, these methods can significantly impact clinical diagnostics by making low-cost and rapid separation possible.

This article describes the impact of restricting the air intake in industrial 250 m3 WEMCO flotation cells at Los Pelambres concentrator. The influence of this air restriction on the hydrodynamic and metallurgical performance of this type of machine was evaluated. The experiments were conducted in single flotation cells and in entire rougher banks. In all cases, the gas holdup was measured to estimate the effectiveness of the obstruction system to decrease the air concentration. In single cells, axial profiles for solid percentage and particle size were evaluated. In addition, a mass balance was conducted to assess the copper recovery and concentrate features. In individual cells, the air restriction led to a decrease in the gas holdup. However, this slight change was enough to obtain a more stable froth zone and a better solids suspension. The latter was observed as a higher P80 below the pulp-froth interface, a less diluted pulp at this level, a slightly higher Cu recovery, and a coarser concentrate product. A mineralogical analysis of the concentrate sample also showed the presence of coarser liberated Cu-sulfide particles. The results in single cells suggested an improvement in the recovery of coarse particles by a more intense solids suspension. The air intake was also restricted in 3 rougher banks to assess the impact of the air obstruction on the overall performance of the respective circuit. Eleven out of fourteen cells were operated with air restriction, which led to a significant recovery improvement of 0.9%-1.6% (absolute) with a 95% confidence level. Size-by-size mass balances were also conducted for the rougher circuits, which proved that the recovery improvements were justified by the simultaneous increase in the recovery of coarse and fine particles. Thus, a restriction of the air intake showed that the decrease in the gas holdup (and in the bubble surface area flux) was compensated by a better solids suspension and a higher turbulence in the impeller. The former promotes the recovery of coarse particles, whereas the latter improves the interaction between bubbles and fine particles. Further developments are being made to implement a regulatory control strategy to control the air intake in self-aspirated flotation cells, and to use this approach for optimizing industrial flotation banks.

Abstract: The most common genetic cause of amyotrophic lateral sclerosis (ALS) and frontotemporal dementia (FTD) is the presence of poly-PR/GR dipeptide repeats which are encoded by the C9orf72 gene. Recently, it was shown that poly-PR/GR alters chromatin accessibility which results in stabilization and enhancement of transcriptional activity of the tumor suppressor p53 in several neurodegenerative disease models. Reduction of p53 protein levels in cell and model organisms protects against neurotoxicity of poly-PR, and partially protects against neurotoxicity of poly-GR. Here, we aimed to study the detailed molecular mechanisms how p53 contributes to poly-PR/GR mediated neurodegeneration. Using a combination of biophysical techniques such as nuclear magnetic resonance (NMR) spectroscopy, fluorescence polarization, turbidity assays and differential interference contrast (DIC) microscopy, we found that p53 physically interacts with poly-PR/GR and triggers liquid-liquid phase separation of p53. We identified p53 transactivation domain 2 (TAD2) as the main binding site for PR25/GR25 and show that binding of poly-PR/GR to p53 is mediated by a network of electrostatic and/or hydrophobic interactions. Our findings might help to understand the mechanistic role of p53 in poly-PR/GR - associated neurodegeneration.

In this paper, we introduce a new class of open sets that is called is*-open set . Also, we present the notion of is*-continuous, is*-open, is*-irresolute, is*-totally continuous, and is-contra-continuous mappings, and we investigate some properties of these mappings. Furthermore, we introduce some is*-separation axioms, and is*-mappings are related with is*-separation axioms. . .

Mill scale is the by-product of iron and steel industry. It can be recycled via sinter plant or solid as sinter feed materials. 85 to 90% of the constituent particles are more than 0.008 inches. The iron content is near around 70 %, with a very small amount of alkaline compounds and non-ferrous metals. Mill scale is polluted and contaminated with lubricants, oils and greases from the equipment. In this experiment for recovering of oil from mill scale, it is treated with three different methods. Then all methods were compared according to the ability of oil elimination and iron recovered. After washing and boiling with surfactants, large amount of polluted waste water becomes a problem for environment so this wastewater was utilized for making of Microbial Fuel Cells (MFCs), production of electricity in MFC depends on the biodegradation of organic materials, so different waste were added in wastewater for making MFC. The remaining of MFC was converted in bioethanol, biodiesel and biofertilizer. So this research is economical and environmentally friendly and fulfilled the important aspect of green environment with zero waste. It will be a mile stone in the research of metallurgy, environmental engineering, recycling technology and zero waste management.

The analysis of network structure is essential to many scientific areas, ranging from biology to sociology. As the computational task of clustering these networks into partitions, i.e., solving the community detection problem, is generally NP-hard, heuristic solutions are indispensable. The exploration of expedient heuristics has led to the development of particularly promising approaches in the emerging technology of quantum computing. Motivated by the substantial hardware demands for all established quantum community detection approaches, we introduce a novel QUBO based approach that only needs number-of-nodes many qubits and is represented by a QUBO-matrix as sparse as the input graph's adjacency matrix. The substantial improvement on the sparsity of the QUBO-matrix, which is typically very dense in related work, is achieved through the novel concept of separation-nodes. Instead of assigning every node to a community directly, this approach relies on the identification of a separation-node set, which - upon its removal from the graph - yields a set of connected components, representing the core components of the communities. Employing a greedy heuristic to assign the nodes from the separation-node sets to the identified community cores, subsequent experimental results yield a proof of concept. This work hence displays a promising approach to NISQ-ready quantum community detection, catalyzing the application of quantum computers for the network structure analysis of large scale, real world problem instances.}

NMR spectral datasets, especially in systems with limited samples, can be difficult to interpret if they contain multiple chemical components (phases, polymorphs, molecules, crystals, glasses, etc…) and the possibility of overlapping resonances. In this paper, we benchmark several blind source separation techniques for analysis of NMR spectral datasets containing negative intensity. For benchmarking purposes, we generated a large synthetic datasbase of quadrupolar solid-state NMR-like spectra that model spin-lattice T1 relaxation or nutation tip/flip angle experiments. Our benchmarking approach focused exclusively on the ability of blind source separation techniques to reproduce the spectra of the underlying pure components. In general, we find that FastICA (Fast Independent Component Analysis), SIMPLISMA (SIMPLe-to-use-Interactive Self-modeling Mixture Analysis), and NNMF (Non-Negative Matrix Factorization) are top-performing techniques. We demonstrate that dataset normalization approaches prior to blind source separation do not considerably improve outcomes. Within the range of noise levels studied, we did not find drastic changes to the ranking of techniques. The accuracy of FastICA and SIMPLISMA degrades quickly if excess (unreal) pure components are predicted. Our results indicate poor performance of SVD (Singular Value Decomposition) methods, and we propose alternative techniques for matrix initialization. The benchmarked techniques are also applied to real solid state NMR datasets. In general, the recommendations from the synthetic datasets agree with the recommendations and results from the real data analysis. The discussion provides some additional recommendations for spectroscopists applying blind source separation to NMR datasets, and for future benchmark studies. Applications of blind source separation to NMR datasets containing negative intensity may be especially useful for understanding complex and disordered systems with limited samples and mixtures of chemical components.

The separation of Li+ and [Bmim]+(1-Butyl-3-methylimidazolium) by electrically driven membrane technology was studied. The effects of the types and modification processes of cation exchange membranes, current density, total cation concentration, temperature, and anion types on separation efficiency were investigated. The results indicated that it is feasible to achieve efficient separation of Li+ and [Bmim]+ using the selectivity of cation exchange membranes under electric field. Membrane CMX and the modified membrane A and B which obtained from the CMX showed obvious selective of Li+ from [Bmim]+. When the current density is 5 mA/cm2 and the feed concentrations of Li+ and [Bmim]+ are 0.3 mol/L and 0.2 mol/L, the selective transport coefficient of the modified membrane B can reach 6.2 in the first 120 minutes of the process. Reducing current density and increasing total cation concentration can improve separation efficiency. Lowering the temperature can improve the separation effect, but improvement is not obviously. Changing the anion of the feed from chloride ion to acetate has no effect on the separation.

Metal-organic frameworks (MOFs) represent the largest class of materials among the crystalline porous materials ever developed and have attracted attention as core materials for separation technology. Their extremely uniform pore aperture and nearly unlimited structural and chemical characteristics have attracted great interest and promise in applying MOFs to adsorptive and membrane–based separations. This paper reviews the recent research and development of MOF membranes for gas separation. Strategies for polycrystalline membranes and mixed matrix membranes are discussed, with a focus on separation systems involving hydrocarbon separation and CO2 capture. Challenges and opportunities for the industrial deployment of MOF membranes are also be discussed, providing guidance for the design and fabrication of future high-performance membranes. The contributions of the underlying mechanism to separation performances, and the adopted strategies and membrane processing technologies for breaking the selectivity/permeability trade–off are discussed.

Several studies in computer vision have examined specular removal, which is crucial for object detection and recognition. This research has traditionally been divided into two tasks: specular highlight removal, which focuses on removing specular highlights on object surfaces, and reflection removal, which deals with specular reflections occurring on glass surfaces. In reality, however, both types of specular effects often coexist, making it a fundamental challenge that has not been adequately addressed. Recognizing the necessity of integrating specular components handled in both tasks, we constructed a Specular-Light (S-Light) DB for training single-image-based deep learning models. Moreover, considering the absence of benchmark datasets for quantitative evaluation, the Multi-Scale Normalized Cross Correlation (MS-NCC) metric, which considers the correlation between specular and diffuse components, was introduced to assess the learning outcomes.

Active flow control of canonical laminar separation bubbles by steady and harmonic vortex generator jets (VGJs) was investigated using direct numerical simulations. Both control strategies were found to be effective in controlling the laminar boundary-layer separation. However, the present results indicate that using the same blowing amplitude, harmonic VGJs were more effective and efficient in reducing the separated region than the steady VGJs considering the fact that the harmonic VGJs use less momentum than the steady case. For steady VGJs, longitudinal structures formed immediately downstream of injection location led to formation of hairpin-type vortices causing an earlier transition to turbulence. Symmetric hairpin vortices were shown to develop downstream of the forcing location for the harmonic VGJs as well. However, the increased control effectiveness for harmonic VGJs flow control strategy is attributed to the fact that shear-layer instability mechanism was exploited. As a result, disturbances introduced by VGJs were strongly amplified leading to development of large-scale coherent structures, which are very effective in increasing the momentum exchange, thus, limiting the separated region.

In the context of video background-foreground separation, we propose a compressive online Robust Principal Component Analysis (RPCA) with optical flow that separates recursively a sequence of video frames into foreground (sparse) and background (low-rank) components. This separation method can process per video frame from a small set of measurements, in contrast to conventional batch-based RPCA, which processes the full data. The proposed method also leverages multiple prior information by incorporating previously separated background and foreground frames in an n-l₁ minimization problem. Moreover, optical flow is utilized to estimate motions between the previous foreground frames and then compensate the motions to achieve higher quality prior foregrounds for improving the separation. Our method is tested on several video sequences in different scenarios for online background-foreground separation given compressive measurements. The visual and quantitative results show that the proposed method outperforms other existing methods.

Here, we report a simple and effective method for separation of gram-negative bacteria using aptamer-modified microbeads and acoustophoresis. As acoustophoresis allows for simultaneous washing and size-dependent separation in continuous flow mode, we efficiently obtained gram-negative bacteria that showed high affinity without any additional washing steps. The proposed device has a simple and efficient channel design, utilizing a long, square-shaped microchannel that shows excellent separation performance in terms of the purity, recovery, and concentration factor. Microbeads (10 µm) coated with the GN6 aptamer can specifically bind gram-negative bacteria. Using acoustophoresis, gram-negative bacteria-bound microbeads and other unbound/contaminants can be separated by size with high purity and recovery. The device demonstrated excellent separation performance, with high recovery (up to 98%), high purity (up to 99%), and a high volume rate (500 µL/min), and a concentration factor of up to 20×. The acoustophoresis microfluidic device also showed binding affinity to multiple strains of gram-negative bacteria, but not to gram-positive bacteria. This study presents a new paradigm for early diagnosis of bacterial infectious diseases. In addition to detecting living bacteria or bacteria-derived biomarkers, this protocol can be extended to monitoring the contamination of water resources, and may aid quick responses to bioterrorism and pathogenic bacterial infections.

In this article, we first introduced new types of higher separation axioms called (r,s)-GFS-regular and (r,s)-GFS-normal spaces with the help of (r,s)-generalized fuzzy semi-closed sets (briefly, (r,s)-gfsc sets) and discussed some topological properties of them. Thereafter, we defined a stronger form of (r,s)-gfsc sets called (r,s)-g*fsc sets and investigated some of its features. Moreover, we showed that (r,s)-fsc set → (r,s)-g*fsc set → (r,s)-gfsc set, but the converse may not be true. In addition, we explored new types of fuzzy generalized mappings between double fuzzy topological spaces (U, τ, τ*) and (V, η, η*), and the relationships between these classes of mappings were examined with the help of some illustrative examples. Finally, some new types of compactness via (r,s)-gfso sets were defined and the relationships between them were introduced.

Xylooligosaccharides (XOS) are components of hemicellulose and can be found in wheat bran, and barley hulls. Structurally, XOS consist of two to six xylose residues linked by β-(1,4) bonds. This makes them susceptible to subsequent treatment by intestinal bacteria, but the concentration of XOS is too low to show any prebiotic effects. Some industrial wastes, including brewers’ spent grain (BSG) and wheat bran peels (WBP), represent a major source of xylan, from which XOS is produced to provide a prebiotic effect in populations of colonic commensal microbiota. WBPs and BSGs were treated by microwave and enzymatic hydrolysis. Using the designed microwave pretreated enzymatic hydrolysis, 5.4 g of dry XOS was produced from 50 g WBP powder and 3.6 g dry XOS was produced from 50 g BSG powder. A single microwave treatment on WBP and BSG before enzymatic hydrolysis and 0.25 g/100 g enzyme raw material ratio were determined to be optimal. Effective microwave-assisted enzymatic hydrolysis of WBP and BSG were investigated, and contribute to improving the effectiveness of xylanase on WBP and BSG. Microwave-assisted enzymatic hydrolysis with xylanase and purification, obtaining food-grade XOS, was demonstrated as a step toward industrial-scale production.

Biomass is a widely distributed and renewable source of carbon. The main objective of this work is to produce an activated carbon from coconut shells with suitable characteristics to separate CO2 from biogas. The textural characterization of the adsorbent has been determined. Pure component adsorption isotherms of CO2 and CH4 at 30, 50 and 70 °C have been measured. Moreover, the performance of the produced activated carbon, as potential adsorbent for CO2 capture from a CO2/CH4 gas mixture has been evaluated under dynamic conditions in a purpose-built fixed-bed setup.

As one of the important wastes, waste PET pollutes human living and natural environment seriously. PET is an important solid waste that needs to be recycled at present. The complete degradation of PET was realized at low temperature. The lipophilic hydrophobic membrane was formed on the surface of stainless steel mesh (SSM) by a simple dip coating method, and the oil-water separation material was successfully prepared. Due to the load of degradation products, the surface roughness of SSM increased from 19.09 μm increased to 62.33 μm. The surface changed from hydrophilic to hydrophobic, and the water contact angle increased to 123o. The oil-water separation flux of modified SSM is 9825 L/(m2·h) and the separation efficiency is 98.99%. The modified SSM has good reuse performance. This hydrophobic modification method can also be used to modify other porous substrates, such as activated carbon, filter paper, foam, and other materials. In this study, the porous substrate modified by the degradation product of waste PET was used to prepare oil-water separation materials, which not only solved the problem of white pollution, but also reduced the dependence on non renewable resources in the conventional preparation methods of oil-water separation materials. The research provided new raw materials and methods for the industrial production of oil-water separation materials, and had important application prospects.

In this study, we present the concept of interval-valued fuzzy soft point and then introduce the notions of neighborhood and quasi-neighbourhood of it in interval-valued fuzzy soft topological spaces. Separation axioms in interval-valued fuzzy soft topology, so-called $q$-$T_{i}$ for $ i=0,1,2,3,4 ,$ is introduced and some of its basic properties are also studied.

Considering the high potential of hydrogen (H₂) as a clean energy carrier, the implementation of high performance and cost-effective biohydrogen (bioH₂) purification techniques is of vital importance, particularly in fuel cell applications. In this context, membrane technology is a potentially energy-saving solution to obtain high-quality biohydrogen. The most promising poly(ionic liquid) (PIL) - ionic liquid (IL) composite membranes previously studied by our group for CO₂/N₂ separation, containing pyrrolidinium-based PILs with fluorinated or cyano-functionalized anions, were chosen as starting point to explore the potential of PIL–IL membranes for CO₂/H₂ separation. The CO₂ and H₂ permeation properties at the typical conditions of biohydrogen production (T =308 K and 100 kPa of feed pressure) were measured and discussed. PIL–IL composites prepared with [C(CN)₃]^– anion showed higher CO₂/H₂ selectivities and H₂ diffusivities compared to those containing [NTf₂]^– anion. All the membranes revealed CO₂/H₂ separation performances above the upper bound for this specific separation, highlighting the composite incorporating 60 wt% of [C₂mim][C(CN)₃] IL.

This research was presented the special designed microfluidic device generated for sperm separation based on assumption of different surface electrical charged of sperms X and Y. However, to avoid ethical problem, the microfluidic chip has been tested with the mimic electrical charged particles, TiO₂-coated Polystyrene beads, (TiO₂-coated Ps-beads), instead of spermatozoa. The work has been separated into three main parts. Firstly, the simply but efficient fabrication of negatively charged TiO₂-coated Ps-beads has been presented. In addition, various characterization techniques such as X-ray diffraction (XRD), Tungsten Scanning Electron Microscopy (W-SEM) with energy-dispersive X-ray spectroscopy (EDS) mode, and X-ray Absorption Spectroscopy (XAS), have been reported in this work to elucidate the reasons behind the persistence of negatively charged on the surface of TiO₂-coated Ps-beads. Results show that the fabricated TiO₂-coated Ps-beads was partly coated in the mixed forms of amorphous Ti⁴⁺ and had caused a negatively charge to appear on the surface after fabrication and had sustained its electrical charged for long. Secondly, process of simulation and fabrication of microfluidic device was presented. Finally the negatively charged TiO₂-coated Ps-beads were tested in this microfluidic devices. For design of microfluidic devices integrated with a couple of microelectrodes, the simulated structures were fabricated by photolithographic technique and tested with the Ps-beads. Percentage of validation for Ps-beads separation indicated that the 100 mm-distance-between-electrodes microfluidic device exhibits to be the highest performance prototype at 86.96%. For further confirmation, another model so called the single path prototype has been established. It is confirmed by 92.59% of validation for the utilization of the device. The successfully designed microfluidic devices can be examined with actual spermatozoa later. Furthermore, process to fabricate the negatively charged TiO₂-coated Ps-beads can be established as testified samples for development of other microfluidic devices.

This study introduces an innovative approach to designing membranes capable of separating CO2 from industrial gas streams at higher temperatures. The novel membrane design seeks to leverage the well-researched high-temperature CO2 adsorbent, hydrotalcite, by transforming it into a membrane. This is achieved by combining it with an amorphous organo-silica-based matrix, extending the polymer-based Mixed Matrix Membrane concept to inorganic compounds. Following the membrane material preparation and investigation of the individual membrane in Part 1 of this study, we examine its permeation and selectivity here. The pure 200 nm thick hydrotalcite membrane exhibits Knudsen behavior due to large intercrystalline pores. In contrast, the organo-silica membrane demonstrates a permselectivity of 13.5 and permeance for CO2 of 1.3 107 mol m2 s1 Pa1 at 25°C, at 150°C the good separation behavior is reduced. Combining both components results in a hybrid microstructure, featuring selective surface diffusion in the microporous regions and unselective Knudsen diffusion in the mesoporous regions. Further attempts to bridge both components to form a purely microporous microstructure are outlined.

This study describes the synthesis and characterization of mixed hydrotalcite–organosilica membrane for gas separation. Hydrotalcite exhibits the capability to adsorb carbon dioxide at elevated temperatures. High surface area and favorable coating properties are essential to harness its potential for practical applications. Stable alcohol-based dispersions are needed for thin film applications of mixed membranes containing hydrotalcite. Currently, producing such dispersions without the need for delamination and dispersion agents is a challenging task. This work introduces for the first time a manufacturing approach to overcoming the drawbacks mentioned above. It includes a synthesis of hydrotalcite nanoparticles, followed by agent-free delamination of their layers and final dispersion into alcohol without dispersion agents. Further, the hydrotalcite-derived sorption agent is dispersed in a matrix based on organo-silica gels derived from 1,2-bis(triethoxysilyl)ethane (BTESE). The analytical results indicate that the interconnection between hydrotalcite and BTESE-derived gel occurs via forming a strong hydrogen bonding system between the interlayer species (OH groups, CO32-) of hydrotalcite and oxygen and silanol active gel centers. These findings lay the foundation for applications involving incorporating hydrotalcite-like compounds into silica matrices, ultimately enabling the development of materials with exceptional mass transfer properties. In part 2 of this study, gas separation performance of the organo-silica and the hydrotalcite-like materials and their combined form will be investigated

In this article, we first defined a stronger form of (r,s)-generalized fuzzy semi-closed sets (briefly, (r,s)-gfsc sets) called (r,s)-g*fsc sets and investigated some of its features. Moreover, we showed that (r,s)-fsc set → (r,s)-g*fsc set → (r,s)-gfsc set, but the converse may not be true. In addition, we explored novel types of fuzzy generalized mappings between double fuzzy topological spaces (U, τ, τ*) and (V, η, η*), and the relationships between these classes of mappings were examined with the help of some illustrative examples. Thereafter, we introduced novel types of higher separation axioms called (r,s)-GFS-regular and (r,s)-GFS-normal spaces with the help of (r,s)-gfsc sets and discussed some topological properties of them. Finally, some novel types of compactness via (r,s)-gfso sets were defined and the relationships between them were introduced.

Lavander distillation leads to huge quantities of solid waste produced yearly. This waste is usually discarded resulting in serious environmental issues. However, it still contains residual essential oil and other bioactive compounds. This research reports on the development and comparison of optimized solid-liquid separation methods, i.e. microwave (MAE) and ultrasound assisted extraction (UAE) of phenolic compounds from lavender distillation waste. Optimal pretreatment conditions, such as waste moisture content and particle size were also determined. The extracts were spray or freeze-dried and the resulting powders were characterized for their physicochemical properties. The majority of the original phenolic compounds in lavender were found in the leachate fraction after distillation (61%), while 43% in the solid waste. Drying of the solid waste before extraction affected the process efficiency. UAE led to higher phenolic content and antioxidant properties compared to MAE. Drying (spray or freeze) the extracts did not significantly affect their phenolic content, while the use of maltodextrin as a drying agent improved the drying process yield especially in the freeze-drying method. It is concluded that valorization of lavender distillation wastes can be achieved via an integrated process consisting of a green extraction method and a consequent drying process that result in a stable bioactive powder.

(1) Background: The synthesis of core-shell magnetic mesoporous nanoparticles (MMSN) from phase transfer process is usually performed at 100-250 mg scale. At the gram scale, nanoparticles without core or with multicore systems are observed. (2) Methods: Iron oxide core nanoparticles (IO) were synthesized through thermal decomposition procedure of -FeO in oleic acid. Phase transfer from chloroform to water was then performed in order to wrap IO with mesoporous silica shell through the sol-gel procedure. MMSN were then functionalized with DTPA, and used for the separation of metal ions. Their toxicity was evaluated (3) Results: The phase transfer pro-cedure was crucial to obtained MMSN at large scale. Three synthesis parameters were rigorously controlled: temperature, time and glassware. Homogeneous dispersion of MMSN at the gram scale was successfully obtained. After functionalization with DTPA, the MMSN-DTPA were shown to have a strong affinity for Ni ions. Furthermore toxicity was evaluated in cells, zebrafish and through seahorse metabolic assays, and the nanoparticles were found nontoxic. (4) Conclusions: We developed a method of preparation of MMSN at the gram scale. After function-alization with DTPA, the nanoparticles were efficient in metal ion removal and separation, fur-thermore, no toxicity was noticed up to 125 µg.mL-1 in zebrafish.

Separation and interpretation of rebellious Circulating Tumor Cells (CTCs) originating from the primary tumor or cancer tissue plays a significant role in diagnostics, cancer progression analyses, suitable medicine exploration, and treatment proficiency examination. Cancer metastasis occurs when CTCs spread throughout the body and invade healthy tissues, leading to new tumors in that area. Although a dramatic rate of deaths begins from spreading CTCs around the body, valuable measures have been made to control their development. However, the first step is separating these harmful cells from the bloodstream and investigating their features. Having examined the characteristics of CTCs as cancer’s main strength, researchers can introduce complementary treatments that can affect cancerous cells without damaging the healthy cells. Therefore, according to their unique characteristics, numerous techniques have been established for continuous and fast separation and sorting of CTCs. Nevertheless, few separators enjoy the efficient performance and appropriate accuracy and can be produced in mass numbers due to the available fabrication equipment. Microfabrication advancements enable separators to combine the advantages of active and passive methods in a small-scale platform for probing individual cells and separation purposes. Reduction in reagents, sample volume, analysis time, and less harmfulness to patients are some of the motivations that encourage researchers to employ microfluidic instruments for CTCs separation from other blood cells over the last two decades. However, microfabrication limitations mean effective separators, and the diagnostic option they provide, are not readily available. Addressing these limitations requires optimizing the design and fabrication of separators such that they are reduced in their size and fabrication cost, while also maintaining high-throughput separating capability. The emergence of the Lab-On-a-Chip (LOC) and then Lab-On-a-CD (LOCD) technologies, having more inherent benefits than conventional microfluidic devices, has created new opportunities and become increasingly widespread in recent years. Evidence suggests that employing single methodologies or integrating approaches without sufficient understanding of potential outcomes is unlikely to result in successful diagnostic results. This paper contributes an extensive review of several separation systems, including fundamental theories and experimental details, and describes detailed operating principles and device performance.

Remotely Piloted Aircraft Systems (RPAS) are increasingly becoming relevant actors flying through the airspace and will assume much more importance in the future perspective. In order to allow their safe integration with manned conventional traffic in non-segregated airspaces, in accordance with the overall Air Traffic Management (ATM) paradigm, specific enabling technologies are needed. As well known, among the enabling technologies identified as crucial for RPAS integration into the overall ATM system, the Detect and Avoid (DAA) technology is fundamental. In the meantime, to support extended surveillance, the universal introduction on-board of aircraft of cooperative Automatic Dependent Surveillance – Broadcast (ADS-B) is increasingly implemented, having the potential to allow coverage of the whole airspace also in remote areas not usually covered by conventional radar surveillance. In this paper, the experimental results are presented and discussed that have been obtained through the real-time validation, with hardware and human in the loop (RTS-HIL) simulations, of an automatic ADS-B based Separation Assurance and Collision Avoidance System aimed to support RPAS automatic operations as well as remote pilot decision making. In the paper, after an introductory outline of the Concept of Operations (ConOps) of the system and of its architectural organization, while also providing basic information about the main system functionalities, the description is reported of the tests that have been carried out and the obtained results are described and discussed, in order to emphasize the performances and limitations of the proposed system. In particular, not only the quantitative performances obtained are reported and commented but also the feedbacks received by the pilots in order to improve the system are described, for instance in terms of preferred typology of conflict resolution manoeuver elaborated by the system.

The way in which a perforated structure is formed has attracted much interest in the porous membrane research community. This novel structure gives materials an excellent antifouling property as well as a low operating pressure and other benefits. Unfortunately, the current membrane fabrication methods usually involve multi-step processes and the use of organic solvents or additives. Our study is the first to offer a way to prepare perforated membrane by using a physical foaming technique with CO₂ as the blowing agent. We selected thermoplastic polyurethane (TPU) as the base material because it is a biocompatible elastomer with excellent tensility, high abrasion resistance, and good elastic resilience. Various processing parameters, which included the saturation pressure, the foaming temperature, and the membrane thickness, were applied to adjust the TPU membrane’s perforated morphology. We proposed a possible formation mechanism of the perforated membrane. The as-prepared TPU membrane had good mechanical properties with a tensile strength of about 5 MPa and an elongation at break above 100%. Such mechanical properties make this novel membrane usable as a self-standing filter device. In addition, its straight-through channel structure can separate particles and meet different separation requirements.

Membrane processes, such as microfiltration, ultrafiltration, and nanofiltration are increasingly used for various applications in both upstream and downstream processing. Membrane-based processes play a critical role in the field of separation/purification of biotechnological products, including protein production/purification. The possibility of using membranes to separate peptides from a chicken byproduct hydrolysate and the effect of the performed downstream processing on the DPP-IV inhibitory activity of MDCR (mechanical deboning chicken residue) has been investigated. The chicken byproduct hydrolysate was prepared by enzymatic hydrolysis followed by MF, UF, NF, and RO separation. The LC-OCD analysis confirmed that NF and RO would retain the bioactive peptides in the concentrate in comparison to MF and UF. Bioactivity was correlated with molecular weight distribution profiles and average molecular weights. Permeates after ultrafiltration showed an IC50 value of 0.75 mg/mL, comparable to other potent DPP-IV inhibitors derived from various food sources, and significantly more potent compared to the microfiltration sample, which showed an IC50 value of 1.04 mg/mL. The average molecular weight of the permeates calculated from the SEC chromatograms was 883 g/mol for UF and 1437 g/mol for MF. Of the four membranes studied, the UF membrane showed the best separation properties with respect to maximizing the yield and up-concentration of the bioactive peptides. Overall, UF was demonstrated to be a feasible technology for the removal of the undesired high molecular weight substances and up-concentration of small molecular weight bioactive peptides from chicken byproduct hydrolysate.

In this study, high-performance FAU (NaY type) zeolite membranes were successfully synthesized using small-sized seeds of 50 nm, and their gas separation performance was systematically evaluated. Employing nano-sized NaY seeds and an ultra-dilute reaction solution with a molar composition of 80 Na2O: 1Al2O3: 19 SiO2: 5000H2O, the effects of synthesis temperature, crystallization time, and porous support (α-Al2O3 or mullite) on the formation of FAU membranes were investigated. The results illustrated that further extending the crystallization time or increasing the synthesis temperature led to the formation of a NaP impurity phase on the FAU membrane layer. The most promising FAU membrane with a thickness of 2.7 µm was synthesized on an α-Al2O3 support at 368 K for 8 h, and had good reproducibility. The H2 permeance of the membrane was as high as 5.34×10-7 mol/(m2 s Pa), and the H2/C3H8 and H2/i-C4H10 selectivities were 183 and 315, respectively. The C3H6/C3H8 selectivity of the membrane was as high as 46 with a remarkably high C3H6 permeance of 1.35× 10-7 mol/(m2 s Pa). The excellent separation performance of the membrane is mainly attributed to the thin, defect-free membrane layer and relatively wide pore size (0.74 nm).

This paper presents a finite element analysis of the bi-directional orthogonal model, which incorporates individual crack strain separation and tracking. The objective of the research is to expand the current shear friction model to manage bi-directional cracking at any angle, allowing for a more universal model that can be applied to intricate structures and non-proportional loading cases. The proposed model was initially developed as a total strain-based model, with the assumption that crack strains are equivalent to total strains, but was subsequently recalculated to improve accuracy by separating crack strains from total strains. Furthermore, a separate crack strain formulation was created to account for strains in the concrete's uncracked portions and locked-in crack strains. The article then discusses the testing of various convergence methods and loading programs to achieve high convergence. Comparative analyses of the generalized shear friction model with other models for crack orientation and loading cases similar to those of a reinforced concrete membrane are also presented. The MATLAB program successfully applied the bi-directional cracking model for one finite element under a uniform cyclical strain state, using a secant stiffness formulation.

Gas membrane-based separation is considered one of the furthermost effective technology to address energy efficiency and large footprint challenges. Various classes of advanced materials including polymers, zeolites, porous carbons and metal–organic frameworks (MOFs) were attempted as membranes for gas separation. MOFs, among other porous materials, possess uniquely tunable nature, in which the pore size and environment can be controlled by connecting metal ions (or metal ion clusters) with organic linkers with various functionalities. This feature makes them attractive for thin membrane fabrication, as both diffusion and solubility components of permeability can be altered. It is interesting to notice that numerous reports have addressed the synthesis of different MOFs, fabrication of their corresponding thin films and their applications, nonetheless, relatively limited studies addressed their gas separation application as membranes. In this review, we provide a synopsis of the various MOF-based membranes that were fabricated in the last decade. In this review we propose a short introduction touching on the gas separation membrane technology and we shed light on (i) the various techniques developed for the fabrication of MOF as membranes and (ii) challenges and application for MOF thin film membranes in various important gas separation applications.

Extracellular vesicles (EVs) are cell-derived membranous particles secreted by all cell types into the extracellular milieu. EVs carry, protect, and transport a wide array of bioactive cargoes to recipient/target cells. EVs regulate physiological and pathophysiological processes in recipient cells and are important in therapeutics/drug delivery. Despite these great attributes of EVs, an efficient protocol for EV separation from biofluids is lacking. Numerous techniques have been adapted for the separation of EVs with size exclusion chromatography (SEC)-based methods being the most promising. Here, we review the SEC protocols used for EV separation, and discuss opportunities for significant improvements, such as the development of novel particle purification liquid chromatography (PPLC) system capable of tandem purification and characterization of biological and synthetic particles with near-single vesicle resolution. Finally, we identify future perspectives and current issues to make PPLC a tool capable of providing a unified, automated, adaptable, yet simple and affordable particle separation resource.

The aim of this paper is to apply a new lane separation methodology for the maritime sector emissions attributed to the different vessel types and marine traffic loads in the Mediterranean and the Black Sea defined via the European Marine and Observation Data network (EMODnet), developed in 2016. This methodology is implemented for the first time on the Copernicus Atmospheric Monitoring Service Global Shipping (CAMS-GLOB-SHIP v2.1) nitrogen dioxide (NOX) emissions inventory, on the Sentinel-5 Precursor TROPOspheric Monitoring Instrument (TROPOMI) nitrogen dioxide (NO2) tropospheric vertical column densities and on the LOTOS-EUROS (LOng Term Ozone Simulation – EURopean Operational Smog) chemical transport model simulations. By applying this new, EMODnet-based lane separation method to the CAMS-GLOB-SHIP v2.1 emission inventory, we find that cargo and tanker vessels account for approximately 80% of the total emissions in the Mediterranean, followed by fishing, passenger, and other vessel emissions with contributions of 8%, 7% and 5%, respectively. Tropospheric NO2 vertical column densities sensed by TROPOMI for 2019 and simulated by the LOTOS-EUROS CTM have been successfully attributed to the major vessel activities in the Mediterranean; the mean annual NO2 load of the observations and the simulations reported for the entire maritime EMODnet-reported fleet of the Mediterranean is in satisfactory agreement, 1.26 ± 0.56x1015 molecules cm-2 and 0.98 ± 0.41x1015 molecules cm-2, respectively. The spatial correlation of the annual maritime NO2 loads of all vessel types between observation and simulation ranges between 0.93 and 0.98. On seasonal basis, both observations and simulations show a common variability. The winter-time comparisons are in excellent agreement for the highest emitting sector, cargo vessels, with the observations reporting a mean load of 0.98 ± 0.54 and the simulations of 0.81 ± 0.45x1015 molecules cm-2 and correlation of 0.88. Similarly, the passenger sector reports 0.45 ± 0.49 and 0.39 ± 0.45x1015 molecules cm-2 respectively, with correlation of 0.95. In summertime, the simulations report a higher decrease in modelled tropospheric columns than the observations, however still resulting in a high correlation between 0.85 and 0.94 for all sectors. These encouraging findings will permit us to proceed with creating a top-down inventory for NOx shipping emissions using S5P/TROPOMI satellite observations and a data assimilation technique based on the LOTOS-EUROS chemical transport model.

Sehezar area is located in southern Tonokabon in Mazandaran province, north of Iran, near the Tarom – Hashdtjin belt. The existence of granitoid masses in the region can be important in terms of the potential of mineralization. Geochemical anomaly separation from the background is one of the important steps in mineral exploration. In the past decades, geochemical anomalies have been identified by means of various methods. Some of these separation methods include: statistical analysis methods (like univariate, bivariate, multivariate statistics), spatial statistical methods and fractal and multi-fractal methods. To identify the anomalous area, 71 stream sediment samples were collected from the area and analyzed by the ICP-MS method, and then interpreted. Initially, data were normalized and afterwards, univariate analysis (threshold limit and screening (P.N) methods) was used, in which results of the probable and definite anomaly of the threshold method were confirmed by the P.N screening method. Finally, the maps of the anomal zones were drawn. Then, bivariate analysis (Pearson correlation coefficients) and multivariate analysis on normal data were performed on SPSS software, in which factor analysis and cluster analysis were used for multivariate analysis. As a result of using the factor analysis method, six factors were identified and factor maps were drawn by the Surfer software. Also, by using cluster analysis, the variables were divided into two groups. In order for a better separation of the geochemical anomaly from the background, in addition to the threshold method, the Concentration - Area fractal method was used. Here, the fractal geometry using full-logarithmic graphs of the Concentration - Area obtained is capable of separating the stairs of different sections (background, threshold, and anomaly) with respect to the angle coefficient of the Concentration - Area plot. Then, in conclusion, results of these methods were compared and investigated, and finally, the anomalies area maps of the Au, Ag, Cu, Fe, W elements were drawn by Concentration - Area fractal and threshold methods and anomalous zones were introduced.

Background: Modern MEG devices include 102 sensor triplets containing one magnetometer and two planar gradiometers. The first processing step is often a signal space separation (SSS), which provides a powerful noise reduction. A question commonly raised by researchers and reviewers is which data should be employed in source reconstruction: (1) magnetometers only, (2) gradiometers only, (3) magnetometers and gradiometers together. The MEG community is currently divided about the proper answer and strong arguments in favor and against these three approaches often expressed. Methods: First, we provide theoretical evidence that both gradiometers and magnetometers contain the same information after SSS, and argue that they both result from the backprojection of the same SSS components. Then, we compare beamforming source reconstructions from magnetometers and gradiometers in real MEG recordings before and after SSS. Results: Without SSS, the correlation between source time series extracted from magnetometers and gradiometers was high, with Pearson correlation coefficient r=0.5-0.8. After SSS, these correlation values increased dramatically, reaching over 0.90 across all cortical areas. Conclusions: After SSS, almost identical source reconstructions (r>0.9) can be obtained with magnetometers and gradiometers, as long as regularization is selected appropriately to account for the different properties in magnetometers and gradiometers covariance matrices.

The surge in popularity of Delta-8 Tetrahydrocannabinol (D8-THC) products, coupled with a lack of stringent regulation and oversight, has given rise to concerns regarding consumer safety and compliance with existing laws. This article delves into the challenges posed by the unregulated sale of D8-THC products, emphasizing the potential for contamination with prohibited constituents, including Delta-9 Tetrahydrocannabinol (D9-THC). The 2018 Farm Bill dictates that D9-THC concentrations must not exceed 0.3%, necessitating precise testing methods for accurate validation. Existing testing procedures, particularly involving High-Performance Liquid Chromatography (HPLC), face difficulties in distinguishing between D8 and D9 peaks, necessitating adjustments in parameters to enhance accuracy. The development of more refined testing methodologies is crucial for companies to ensure compliance, prevent adverse health effects, and provide consumers with accurately characterized cannabinoid profiles in the products they purchase.

This paper proposes a novel efficient multistage algorithm to extract source speech signals from a noisy convolutive mixture. The proposed approach comprises of two stages named Blind Source Separation (BSS) and De-noising. A hybrid source prior model separates the source signals from the noisy reverberant mixture in the BSS stage. Moreover, we model the low and high-energy components by generalized multivariate Gaussian and super-Gaussian models, respectively. We use Minimum Mean Square Error (MMSE) to reduce noise in the noisy convolutive mixture signal in the de-noising stage. Furthermore, two proposed models investigate the performance gain. In the first model, the speech signal is separated from the observed noisy convolutive mixture in the BSS stage, followed by suppression of noise in the estimated source signals in the de-noising module. In the second approach, the noise is reduced using the MMSE filtering technique in the received noisy convolutive mixture at the de-noising stage, followed by separation of source signals from the de-noised reverberant mixture at the BSS stage. We evaluate the performance of the proposed scheme in terms of signal-to-distortion ratio (SDR) with respect to other well-known multistage BSS methods. The results show the superior performance of the proposed algorithm over the other state-of-the-art methods.

The formation and functioning of membrane-less organelles (MLOs) is one of the main driving forces in the molecular life of the cell. These processes are based on the separation of biopolymers into phases regulated by multiple specific and nonspecific inter- and intramolecular interactions. Among the realm of MLOs, a special place is taken by the promyelocytic leukemia nuclear bodies (PML-NBs or PML bodies), which are the intranuclear compartments involved in the regulation of cellular metabolism, transcription, maintenance of genome stability, response to viral infection, apoptosis, and tumor suppression. According to the accepted models, specific interactions, such as SUMO/SIM, formation of disulfide bonds, etc., play a decisive role in the biogenesis of PML bodies. In this work, a number of bioinformatics approaches were used to study proteins found in the proteome of PML-bodies for their tendency to spontaneous liquid-liquid phase separation (LLPS), which is usually caused by weak nonspecific interactions. 205 proteins found in PML bodies have been identified. It has been suggested that UBC9, P53, HIPK2, and SUMO1 can be considered as the scaffold proteins of PML bodies. It was shown that more than half of the proteins in the analyzed proteome are capable of spontaneous LLPS, with 85% of the analyzed proteins being intrinsically disordered proteins (IDPs), and remaining 15% being proteins with intrinsically disordered protein regions (IDPRs). About 44% of all proteins analyzed in this study contain SUMO binding sites and can potentially be SOMYylated. These data suggest that weak nonspecific interactions play a significantly larger role in the formation and biogenesis of PML bodies than previously expected.

Nickel is widely used in industrial processes and plays a crucial role in many applications. However, most of the nickel resource mainly exists as nickel oxide in laterite nickel ore with complex composition, resulting in difficulty in upgrading the nickel content using physical separation methods. In this study, high-grade ferronickel concentrates were obtained through a carbothermal reduction and magnetic separation using laterite nickel ore and anthracite as raw materials. The effects of different types of additives (CaF2, Na2SO4 and H3BO3), carbon ratio (nc/no in metal oxides) and grinding time on the recoveries and grades of ferronickel concentrates were experimentally investigated, along with the microstructure and chemical composition of the products. CaF2 was proved to be the primary active additive in the aggregation and growth of the ferronickel particles, and the improvement of the grade of the product. Under the optimal conditions of CaF2 addition of 12 wt.%, carbon ratio of 1.4, and grinding time of 240 s, high-grade magnetically separable ferronickel concentrate with nickel grade 8.93 wt.% and iron grade 63.96 wt.% was successfully prepared. This work presents a practical method for the highly efficient recovery and utilization of iron and nickel from low-grade laterite nickel ore, contributing to the development of strategies for the sustainable extraction and utilization of nickel resources.

A set of aromatic copolyimides was obtained by reaction of 4,4′-(hexafluoroisopropylidene) diphthalic anhydride (6FDA), and mixtures of the diamines 1,4-bis(4-amino-2-trifluoromethylphenoxy)-2,5-di-tert-butylbenzene (CF3TBAPB) and 3,5-diamino benzoic acid (DABA). These polymers were characterized and compared with the homopolymer derived from 6FDA and CF3TBAPB. All copolyimides showed high molecular weight values and good mechanical properties. The presence of carboxylic groups in these copolymers allowed their cross-linking by reaction with 1,4-butanediol. The crosslinked polymer films were extensively characterized and it was observed that the degree of crosslinking was low in the copolyimides possessing a small number of carboxyl groups. The degradation temperature of these crosslinked copolyimides was lower than their corresponding non-crosslinked ones. Glass transition temperatures were higher than 260 oC, showing the non-crosslinked copolyimides the highest values. Young moduli of these crosslinked showed values higher than 1.9 GPa, and slightly lower elongation at break when compared with the precursor copolyimides. All copolyimides (precursor, and crosslinked ones) films could be tested as gas separation membranes. It was seen that CO2 permeability values were around 100 barrer, having better selectivity than that of the homopolymer. Moreover, the plasticization resistance of the crosslinked material having a large number of carboxylic groups was excellent.

Liquid-liquid phase separation (LLPS) of proteins has been found ubiquitously in eukaryotic cells, critical in the controlling of many biological processes through forming a temporary condensed phase with different bimolecular components. TDP-43 is recruited to stress granules in cells and is the main component of TDP-43 granules and proteinaceous amyloid inclusions in patients with amyotrophic lateral sclerosis (ALS). TDP-43 low complexity domain (LCD) is able to demix in solution forming the protein condensed droplets. The molecular interactions regulating its LLPS were investigated at the protein fusion equilibrium stage, where the droplets stopped growing. We found the molecules in the droplet were still liquid-like but with enhanced intermolecular helix-helix interaction in the LCD. The protein would start to aggregate after about 200 minutes of lag time and aggregate slower than at the condition when the protein does not phase separate or the molecules have a reduced intermolecular helical interaction. A structural transition intermediate towards protein aggregation was also discovered involving a decrease of the intermolecular helix-helix interaction and a reduction in the helicity. Therefore, LLPS and the intermolecular helical interaction could help maintain the stability of TDP-43 LCD.

Nowadays, the imidazolium-based ionic liquids containing acetate counter-ions are attracting much attention as both highly selective absorbents of the acidic gases and CO₂ carriers in the supported ionic liquid membranes. In this regard, the investigation of the gas transport properties of such membranes may be appropriate for better understanding of various factors affecting the separation performance and the selection of the optimal operating conditions. In this work, we have tested CH₄, CO₂ and H₂S permeability across the SILM impregnated by 1-butyl-3-methylimidazolium acetate (bmim[ace]) with the following determination of the ideal selectivity in order to compare the facilitated transport membrane performance with the SILM that dissolves acidic gases physically, namely, containing 1-butyl-3-methylimidazolium tetrafluoroborate (bmim[BF₄]). Both SILMs have showed modest individual gases permeability and ideal selectivity of CO₂/CH₄ and H₂S/CH₄ separation that achieves values up to 15 and 32, respectively. The effect of the feed gas mixture composition on the permeability of acidic gases and permeselectivity of the gas pair was investigated. It turned out that the permeation behavior for the bmim[ace]-based SILM toward the binary CO₂/CH₄, H₂S/CH₄ and ternary CO₂/H₂S/CH₄ mixtures was featured with high acidic gases selectivity due to the relatively low methane penetration through the liquid phase saturated by acidic gases.

Nowadays asymmetric thin film composite (TFC) polymeric hollow fiber (HF) membranes are extensively used in industrial gas/vapor separations, water treatment etc. There are numerous advantages to use hollow fibers such as: low energy requirements, simplicity of operation, and high specificity. In the present article we discuss the progress made during the past decade in the preparation of the HF substrate and preparation/modification of the thin selective layer. Their applications in water treatment, dehydration of alcohols via pervaporation and gas/vapor separation are also demonstrated.

Solid spent nuclear fuel from nuclear power plants has 3.4% fission products (80-160amu), contributing to over 99.8% radioactivity. On the other hand, liquid high-level radioactive waste (HLRW) from spent fuel reprocessing has 98.9% bulk elements (0-60amu) with 0.1% radioactivity. A separation mechanism on the mass categories as groups presents unique opportunities in managing HLRW for the long term with a considerable cost reduction. This paper proposes a thermal plasma-based separation system incorporating atmospheric pressure plasma torches for HLRW mass separation into low-resolution mass groups. Several engineering issues, such as waste preparation, waste injection into the plasma and waste collecting after mass separation, need to be addressed. Using COMSOL Multiphysics simulation, the generic system can be studied using noble gas mass separation and further analyze the mass filter capabilities. This paper provides the history of plasma-based mass separation. Functional modelling of a thermal plasma mass separation system is proposed under atmospheric pressure. Finally, aspects of mass separation simulation using noble gas Argon and Helium inside the plasma mass separation system were studied in COMSOL Multiphysics.

The conversion of C1 gas feedstock, such as carbon monoxide (CO), into useful platform chemicals has attracted considerable interest in industrial biotechnology. One conversion method is electrode-based electron transfer to microorganisms using bioelectrochemical systems (BESs). In this BES system, acetate is the predominant component of various volatile fatty acids (VFAs). To appropriately separate and concentrate the produced acetate, a BES type electrodialysis cell with an anion exchange membrane was constructed and evaluated under various operational conditions, such as the applied external current. The higher acetate flux of 23.9 mmol/m2∙hr was observed under -15 mA current in an electrodialysis-based bioelectrochemical system. In addition, the initial acetate concentration affects the separation efficiency and transportation rate. The maximum flux appeared at 48.6 mmol/m2∙hr when the acetate concentration was 100mM, whereas the effect of the initial pH of the anolyte was negligible. The acetate flux was 14.9 mmol/m2∙hr when actual fermentation broth from BES based CO fermentation, was used as a catholyte. A comparison of the synthetic medium with the actual fermentation medium suggests that unknown substances and metabolites in the actual medium interfere with electrodialysis in the BES. These results provide information on the separation and optimal concentration for VFAs produced by C1 gas fermentation through electrodialysis, and a combination of a BES and electrodialysis.

The horizontal flatbed electrophoresis system has been used for the electrophoresis of protein samples and is often preferred for a two-dimensional polyacrylamide gel electrophoresis. In currently available equipment, cathode and anode electrodes were placed on top of a gel at each end. An electric field entered from the top of a gel, and its strength was relatively weaker in the bottom part of the gel. Such configuration caused migrating protein bands to lie down forward in the migrating direction. New electrodes, i.e., the clamp-shaped and the double-deck electrodes, were developed to simultaneously apply an electric field from the top and bottom of a gel. Electrophoretic separation with these electrodes made protein bands more focused and improved protein band resolutions. When the FIGE technique was tested together with new electrodes, protein bands were aligned nearly vertically and showed the best electrophoretic resolutions.

The neurovascular niche is crucial for constant blood supply and blood-brain barrier (BBB) function and is altered in a number of different neurological conditions, making this an intensely active field of research. Brain vasculature is unique for its tight association of endothelial cells with astrocytic endfeet processes. Separation of the vascular compartment by centrifugation-based methods confirmed enrichment of astrocytic endfeet processes, making it possible to study the entire vascular niche with such methods. Several centrifugation-based separation protocols are found in the literature; however, with some constraints which limit their applicability and the scope of the studies. Here, we describe and validate a protocol for physically separating the neurovascular niche from the parenchyma, which is optimized for smaller tissue quantities. Using endothelial, neuronal and astrocyte markers, we show that quantitative Western blot-based target detection can be performed of both the vascular and parenchymal fractions using as little as a single mouse brain hemisphere. Validation of our protocol in rodent stroke models by detecting changes in serum albumin signals and astrocyte activation, i.e. increased glial fibrillary acidic protein expression, between the ipsilateral and the lesion-free contralateral hemisphere demonstrates this protocol as a new way of detecting BBB breakdown and astrogliosis, respectively.

PEBAX-2533/metal salt/Al salt membranes were prepared for mixed olefin/paraffin separation. PEBAX-2533 with 80% ether group and 20% amide group was suggested as the polymer matrix for comparison of separation performance according to the functional group ratio in copolymer PEBAX. In addition, Al salts were used to stabilize metal ions for a long time as additives. High permeance was expected with the proportion of high ether groups since these functional groups provided relatively permeable regions. As a result, the PEBAX-2533 composite membrane showed a selectivity of 5 (propylene/propane) with 10 GPU. However, the permeance of membrane was not unexpectedly improved and the selectivity was reduced. The result was analyzed by SEM, FT-RAMAN and TGA, including FT-IR. The reduction in separation performance was determined by FT-IR. From these results, in order to stabilize the metal ions interacting with the polymer through Al(NO3)3, it was concluded that specific ratio of amide group was needed in PEBAX as polymer matrix.

In recent years, the chiral biological effects of nanomedicines have become a subject of widespread interest. The research focus has been on understanding the influence of material chirality on cellular transcription and metabolism. Stress granules are membraneless organelles formed through liquid-liquid phase separation of G3BP1 proteins and related compartments. They have been extensively studied and proven to be closely associated with cellular damage repair and metabolism. However, the role and mechanism of chiral nanomaterials in modulating stress granules remain unknown. The aim of this study was to investigate the expression and structural characteristics of stress granules under the individual influence of chiral nanomaterials and in combination with chemotherapy. To achieve this, we constructed a library of chiral ligand-modified materials and employed immunofluorescence, live-cell imaging, and fluorescence recovery after photobleaching assays. We also used proximity labeling techniques combined with proteomics analysis to identify the protein corona adsorbed on the surface of the nanomaterials and explore their relationship with nanomaterial chirality. Our results demonstrate that the assembly of stress granules is chiral-dependent and can be regulated by chiral nanomaterials. Furthermore, we achieved enhanced chemotherapy sensitivity in cancer cells and protected normal cells by exploiting the chiral-dependent modulation of material assembly in stress granules. This study provides important insights into the regulation of membraneless cellular structures based on chiral biological effects.

Proper management of water is a challenge for every individual but especially for companies. Nowadays also legislation obliges companies to clean the wastewater before being discharged into municipal public sewer especially if they use some chemicals or oily elements in their production process. Construction of the wastewater cleaner depends directly on the way of pollution, the amount of contaminated water and the energy demand of the cleaning process. The paper deals with the construction of the wastewater cleaner, which is based on the technology of electro-flotation for the treatment of water contaminated with disperse colorants. The experimental work as well as the modelling using the statistical methods proved the suitability of the chosen technology. Also, each colour combination requires a specific time period for the water treatment. The authors determined the time interval for cleaning the wastewater that was polluted with yellow colour to 33 minutes. Finally, the wastewater cleaner that is based on the electro-flotation technology was included in the company’s reverse logistics system.

Hydrogen from natural gas reforming can be produced efficiently with a high CO2 capture rate. This can be achieved with oxygen-blown autothermal reforming as core technology combined with pressure-swing adsorption for hydrogen purification and refrigeration-based tail gas separation for CO2 capture and recirculation of residual hydrogen, carbon monoxide and methane. The low-temperature tail gas separation section is presented in detail, and to quantify the exergy efficiency of this section, a detailed exergy analysis is conducted. The irreversibilities in 42 different process components are quantified. In order to provide a transparent verification of the consistency of exergy calculations, the total irreversibility rate is calculated by two independent approaches: Through the bottom-up approach, all individual irreversibilities are added to obtain the total irreversibility rate. Through the top-down approach, the total irreversibility rate is calculated solely by the exergy flows crossing the control volume boundaries. The consistency is verified as the comparison of results obtained by the two methods shows a relative deviation of 4·10-7. The exergy efficiency of the CO2 capture process is calculated based on two different definitions. Both methods give a baseline exergy efficiency of 58.38%, which indicates a high degree of exergy utilisation in the process.

Liposome vesicle is an ideal carrier for carbon nanotube (CNT) to serve as the water channel that allows the fast transport of water molecules, and thus enhancing the membrane permeability. However, low quantity of the inserted CNT in the liposome vesicle is an important factor that limited further improvement of the membrane flux. In present study, positively charged lipids (2,3-dioleoyloxy-propyl)-trimethylammonium-chloride (DOTAP) was introduced to the 1,2-dioleoyl-sn-glycero-3-phosphoethanolamineon (DOPE) liposome vesicles to tailor the vesicle charge, so as to evaluate the effect of positively charged DOTAP on the insertion of CNT into liposomes and separation performance of thin-film nanocomposite (TFN) membranes. The results showed that addition of DOTAP induced more quantity of CNT inserted into the liposome vesicles, since the shrinkage rate (k) and permeability (Pf) of liposome vesicles present obvious increase with increased content of DOTAP in the liposome vesicles. Besides, it contributed to 252.3% higher water flux for TFN membranes containing DOPE/DOTAP2:1-CNT liposomes (the mass ratio between DOPE and DOTAP was 2:1) than TFC membranes. More important, it presented 106.7% higher water flux for TFN membranes containing DOPE/DOTAP4:1-CNT liposomes (the mass ratio between DOPE and DOTAP was 4:1), which was originated from the more water channels that the CNT provided in the liposome vesicles. In all, positively charged DOTAP effectively tailored the vesicle charge, which provided a better carrier for the insertion of more quantity of CNT, and contributed to higher permeability of TFN membranes.

Biomass as a whole offers a more diverse potential for valorisation than any other renew-able energy source. As one of the stages in the separation of bio-oil involves the liquid mixture of acetol and acetic acid, and as both components are particularly well suited for valorisation, a hybrid method has been developed for their separation with a high purity level through an approach combining liquid-liquid extraction and rectification. In order to design and simulate the flowsheet, the ChemCAD 7.0 simulation software has been used. Sensitive analyses have been carried out to investigate the influence of the different pa-rameters in the rectification columns such as the reflux ratio, the feed stage location, and the vapour/bottom molar flow ratio. The effect of different extractants and of their excess on the separation process as well as the possibility of regenerating the extractant has also been studied. Tri-n-octylamine has accordingly been selected as a separating agent which has been fully recycled. The end result for separating an initial 48/52 wt% ace-tol/acetic-acid liquid mixture has been acetol with a purity of 99.4 wt% and acetic acid with a purity of 100 wt%.

Oil-water separation using special wettability materials has received much attention due to its low energy consumption and high separation efficiency. Herein, a fluorine-free superhydrophobic cotton fabric(PDMS/STA -coated cotton fabric) was successfully prepared by a simple impregnation method using hydroxyl-capped polydimethylsiloxane (PDMS-OH), tetraethoxysilane (TEOS) and stearic acid (STA) as precursors. The Investigation found that the cross-linking reactions between the hydroxyl groups form PDMS-OH, hydrolyzed TEOS made a strong interact of PDMS-OH and cotton fabric. Besides, a suitable roughness surface of coated cotton fabric was established by introducing STA due to its long chain-structure. The contact angle of this composite can reach 158.7°under optical condition due to its low surface energy and desired roughness. The oil/water separation efficiency of PDMS/STA-coated cotton fabric is higher than 90% even after 10 cycles of oil-water separation, the oil flux can reach 11862.42 L m-2 h-1. In addition, PDMS/STA-coated cotton fabric exhibits excellent chemical stability and durability under extreme conditions such as strong acid (HCl, pH=1~2) and alkali (NaOH, pH=13~14), the hydrophobicity of PDMS/STA-coated cotton fabric was decreased to 147° even after 350 cycles of abrasion testing.

To encourage proper waste management from electrical and electronic devices (e-waste), it is necessary to invest heavily in the development of recycling technologies. One way to improve the process is to automate separating the shredded parts of e-waste using a robot. This paper's literature review, utilizing the Preferred Reporting Items for Systematic reviews and Meta-Analyses (PRISMA) framework, showcases potential robotic technologies for e-waste separation. However, the intricate design of these devices can pose significant challenges in their implementation. Various legal, organizational, and sociological obstacles have left Serbia's e-waste management practice underdeveloped, resulting in an unsatisfactory recycling rate. In this paper we examined the possibility of using robots on the precise example of recycling refrigerators in a recycling center in Eastern Serbia, concluding that such a solution would have multiple positive effects, both on the employees and the working environment, on the operations of the recycling center itself, and on increasing the e-waste recycling rate in the country.

The present study describes the preparation of a composite material consisting of thermoplastic polyurethane-poly (n-isopropylacrylamide) (TPU-PNIPAM), which was employed for the se-lective adsorption separation of alcohol/water mixed solutions for the first time. The findings revealed that TPU and PNIPAM were interconnected through interchain hydrogen bonding, resulting in exposed hydrophobic isopropyl groups while covering the hydrophilic hydrogen bond sites. Selective separation of alcohols from alcohol/water mixed solutions occurred via London dispersion forces between alkyl groups. Increasing the PNIPAM load on the TPU surface led to a decrease in available hydrogen bond sites capable of bonding with water molecules, an increase in dispersible isopropyl groups interacting with alcohol alkyl groups, and enhanced selective adsorption capacity of TPU-PNIPAM towards alcohol/water mixed solutions. Moreover, TPU-PNIPAM exhibited a characteristic fast-slow-fast-equilibrium ad-sorption curve for different initial concentrations of alcohol/water mixtures, and its selective adsorption capacity increased when temperature reached 55℃. In addition to these general trends, under identical conditions, the selective adsorption capacity of TPU-PNIPAM gradually increased by methanol < ethanol < isopropyl alcohol < propyl alcohol, thus indicating a positive correlation between selectivity performance and hydrophobicity level.

The parameters of logistic regression models are usually obtained by the method of maximum likelihood (ML). However, in analyses of small data sets or data sets with unbalanced outcomes or exposures, ML parameter estimates may not exist. This situation has been termed “separation” as the two outcome groups are separated by the values of a covariate or a linear combination of covariates. To overcome the problem of non-existing ML parameter estimates, applying Firth’s correction (FC) was proposed. In practice, however, a principal investigator might be advised to “bring more data” in order to solve a separation issue. We illustrate the problem by means of an examples from colorectal cancer screening and ornithology. It is unclear if such an increasing sample size (ISS) strategy that keeps sampling new observations until separation is removed improves estimation compared to applying FC to the original data set. We performed an extensive simulation study where the main focus was to estimate the cost-adjusted relative efficiency of ML combined with ISS compared to FC. FC yielded reasonably small root mean squared errors and proved to be the more efficient estimator. Given our findings, we propose not to adapt the sample size when separation is encountered but to use FC as the default method of analysis whenever the number of observations or outcome events is critically low.

In this work a series of experiments on the retention of B1 (riboflavin), B2 (thiamine) and B3 (nicotinic acid) vitamins in the HILIC and RPLC conditions have been performed involving the effects of organic modifier type and content, pH of the eluent, and buffering salt (ammonium acetate) concentration in the mobile phase, as well as temperature of the system. For the needs of this studies three columns of different features have been chosen: Acclaim™ Mixed-Mode HILIC-1 (Dionex), Eurospher II 100-5 HILIC (Knauer) and the RPLC column Nucleodur® C18 Gravity – SB (Macherey –Nagel). The influence of acetonitrile and methanol content in the eluent and process temperature have been tested and basing on that the most promising systems have been selected regarding the possible separation of the vitamins mixture. Both pH and buffering salt concentrations in the eluent have been adjusted in order to indicate the most effective system which turned out to be the one involving the Nucleodur column and the eluent with 90% methanol, at pH 6 and Cbuff = 20 mmol/dm3 that enables separation of the mixture within the time as short as 2.5 minutes at 1.0 mL/s flowrate in isocratic conditions.

Despite the fact that strong routine separation methodologies can give reliable specificity and validity at usual working pharmaceuticals concentrations, they may fail at very low concentration levels. This poses considerable challenges for researchers inves-tigating product purity and therapeutic drug monitoring. Sensitivity enhancement pro-cedures are thus required to maximize the performance of separation techniques. Large volume injection, solid phase extraction/solid phase enrichment (SPE/SPEn), pre-, post-, and in-column derivatization, as well as the use of sensitive detection devices are the simplest strategies for improving sensitivity of the separation-based analytical techniques. Large volume injection of samples with online SPE/SPEn coupled with separation techniques increased sensitivity and improved detection as well as quantification limits without affecting peak shape and system performance. Although the primary purpose of derivatization is to improve sensitivity and selectivity, greener derivatization is growing in popularity and should be considered in analytical chemistry. In general, two strategies are essential for accomplishing greener derivatization goals. The first is the search for and use of ecologically acceptable derivatizing reagents, solvents, and reaction conditions. The second is miniaturization and automation of analytical methods. This review discusses significant advances in separation-based analytical techniques, specifically enrichment approaches and detector signal improvement for pharmaceutical quantification in various matrices at very low concentration levels. As a result of improved analytical systems setup in drug assays, the possibility of high-throughput analyses was also highlighted.

The application of diffusion dialysis using various types of ion-exchange membranes for the separation of sulfuric acid and nickel sulfate has been evaluated. The process of dialysis separation of a real waste solution from an electroplating facility containing 252.3 g/L of sulfuric acid, 20.9 g/L of nickel ions and small amounts of zinc, iron, copper ions, etc. has been studied. Heterogeneous cation-exchange membrane containing sulfo groups and heterogeneous anion-exchange membranes with different thicknesses (from 145 μm to 550 μm) and types of fixed groups (4 samples with quaternary amino groups and 1 sample with secondary and tertiary amino groups) are used. The diffusion fluxes of sulfuric acid, nickel sulfate, and the total and osmotic fluxes of the solvent are determined. The use of a cation-exchange membrane does not allow separation of the components, since the fluxes of both components are low and comparable in magnitude. The use of anion-exchange membranes makes it possible to efficiently separate sulfuric acid and nickel sulfate. At the same time, the thin dialysis membrane turns out to be the most effective, as well as the membranes with quaternary amino groups, and the membrane with secondary and tertiary amino groups proved to be the least effective.

Separation of polyethylene glycols (PEGs) into single homologs by reversed-phase chromatography is investigated experimentally and theoretically. The used core-shell column is shown to achieve baseline separation of PEG homologs up to molar weights of at least 5000 g/mol. A detailed study is performed elucidating the role of the operating conditions temperature, eluent composition, and degree of polymerization of the polymer. Applying Martin's rule yields a simple model for retention times that holds for a wide range of conditions. In combination with relations for column efficiency, the role of the operating conditions is discussed and separations are predicted for analytical-scale chromatography. Finally, the approach is included in an efficient process model based on discrete convolution, which is demonstrated to predict with high accuracy also advanced operating modes with arbitrary injection profiles.

In today's society, mankind is confronted with two major problems: the energy crisis and the greenhouse effect. The artificial photosynthesis can use solar energy to convert greenhouse gas CO2 into high-value compounds, which is an ideal solution to alleviate the energy crisis and solve the problem of global warming. The combination of ZnO and polythiophenes (PTh) can make up for each other's drawbacks, thus improving the photoresponse behavior and separation efficiency of photogenerated carriers. PTh layer can transfer photogenerated electrons to ZnO, thereby extending the lifetime of photogenerated charges. The production rate of CH4 from photoreduction of CO2 with ZnO/PTh10 is 4.3 times that of pure ZnO, and the selectivity of CH4 is increased from 70.2% to 92.2%. The conductive PTh can absorb photons to induce π–π* transition, the photogenerated electrons can transfer from LUMO to the conduction band (CB) of ZnO, thus more electrons involve in the reduction of CO2.

Radical changes in the idea of the organization of the intracellular space that occurred in the early 2010-s made it possible to consider the formation and functioning of the so-called membrane-less organelles (MLOs) based on a single physical principle: the liquid-liquid phase separation (LLPS) of biopolymers. Weak nonspecific inter- and intramolecular interactions of disordered polymers, primarily of intrinsically disordered proteins and RNA, play a central role in the initiation and regulation of these processes. On the other hand, in some cases, the "maturation" of MLOs can be accompanied by the "liquid-gel” phase transition, where other types of interactions can play a significant role in reorganization of their structure. In this work, we conducted a bioinformatics analysis of the propensity of the proteomes of two membrane-less organelles formed in response to stress in the same compartment, nucleolus, for spontaneous phase separation and looked at their intrinsic disorder predispositions. These nucleolar MLOs, amyloid bodies (A-bodies) formed in the response to acidosis and heat shock and nuclear stress bodies (nSBs), are characterized by the partially overlapping composition, but show different functional activities and morphologies. We show that the proteomes of these nucleolar biocondensates are differently enriched in proteins, many of with high potential for spontaneous LLPS that correlates with different morphology and function of these organelles. The results of these analyses allowed us to evaluate the role of weak interactions in the formation and functioning of these important organelles.

Numerical methods, including machine learning methods, are now actively used in the applications related to guided wave propagation. The method proposed in this study for material properties characterization is based on the algorithm of the clustering of multivariate data series obtained as a result of the application of the matrix pencil method to the experimental data. In the proposed technique, multi-objective optimization is employed to improve the accuracy of particular parameter identification. At the first stage, the computationally efficient method based on the calculation of the Fourier transform of Green's matrix is employed iteratively and the obtained solution is used for the filter construction with decreasing bandwidth, which allows us to obtain nearly noise-free classified data (with mode separation). The filter provides data separation between all guided waves in a natural way, which is needed at the second stage, where the slower method based on the minimization of the slowness residuals is applied to the data. The method might be applied for material properties identification in plates with thin coatings/interlayers, multi-layered anisotropic laminates etc.

Food analysis demands fast methods for routine control and high throughput of samples. Chromatographic separation enables simultaneous determination of numerous compounds in complex matrices, several approaches increasing separation efficiency and speed of analysis were involved. In this work, modern types of column with monolithic rod or superficially porous particles were employed and compared for determination of eight synthetic food dyes, their chromatographic performance was evaluated. During method optimization, cyano stationary phase Chromolith Performance CN 100 × 4.6 mm and Ascentis Express ES-CN 100 × 4.6 mm, 5 µm were selected for the separation of polar colorants. The separation was performed by gradient elution of acetonitrile/methanol and 2% water solution of ammonium acetate at flow rate 2.0 ml min-1. Mobile phase composition and the gradients were optimized in order to enable efficient separation on both columns. The method using fused-core particle column provided higher separation efficiency, narrow peaks of analytes resulted in increased peak capacity and shortening of analysis time. After the validation, the method was applied for analysis of colored beers, soft drinks and candies.

We have developed an unsteady and non-linear wind synopsis simulator called RIAM-COMPACT (Research Institute for Applied Mechanics, Kyushu University, COMputational Prediction of Airflow over Complex Terrain) in order to simulate the airflow on a microscale, i.e., a few tens of km or less. In RIAM-COMPACT, the large-eddy simulation (LES) has been adopted for turbulence modeling. LES is a technique in which the structures of relatively large eddies are directly simulated and smaller eddies are modeled using a sub-grid scale model. In the present study, we have conducted the numerical wind diagnoses for Taikoyama Wind Farm nacelle separation accident in Japan. The simulation results suggest that all six wind turbines at the Taikoyama Wind Farm are subject to significant influence from separated flow (terrain-induced turbulence) which is generated due to the topographic irregularities in the vicinity of the wind turbines. A proposal has been also made on reconstruction of the wind farm.