The advancement in science and technology has led to luffa sponge (LS) being widely used as a natural material in industrial application as its polyporous structure and light texture. In order to enhance the utility of LS fibers as the reinforcement of lightweight composite materials, this study investigate its water absorption, mechanical properties, anatomical characteristic and thermal performance. Hence, moisture regain, tensile properties of LS fiber bundles were measured in accordance with standards and the structural characteristics were investigated via microscopic observation. Scanning electron microscopy (SEM) was used to observe the surface morphology and fracture surface of fiber bundles. Test results shows that the special structure where the phloem tissues degenerate to cavities had a significant influence on the mechanical properties of LS fiber bundles. Additionally, the transverse sectional area occupied by fibers in a fiber bundle (SF), wall thickness and ratio of wall to lumen of fiber cell, and crystallinity of cellulose had an impact on the mechanical properties of LS fiber bundles. Furthermore, the fiber bundles density of LS varies range of 385.46-468.70 kg/m³, much less than that of jute (1360.40 kg/m³) and Arenga engleri (950.20 kg/m³) while LS fiber bundles has superior specific modulus.

The increasing demand for higher power in rocket launchers is driving the development of higher power nozzles, achieved essentially by increasing the expansion ratio. However, this can lead to flow separation and resulting unsteady, asymmetrical forces, called side loads, which can limit the life of both the nozzle itself and other engine components. If this problem can be overcome, engine performance can be significantly increased. Therefore, various separation control methods have been proposed, but none have been fully implemented to date due to the uncertainties associated with modeling and predicting the flow phenomena. A numerical study of high area ratio rocket engine is presented to analyze the aeroelastic performance of the structure under the condition of flow separation. The finite volume method, the 2nd order upwind scheme and the extended wall function are used to analyze the flow inside the rocket nozzle and the transition of the Free Shock Separation (FSS) to Restricted Shock Separation (RSS) separation pattern ) to be discussed in detail. Since the location of the flow separation point depends heavily on the flow.

Pea shoots is a popular vegetable in certain regions of the world due to their unique taste and abundance of health-promoting phytochemicals. The perishable nature and susceptibility of root rot of pea shoots necessitate a new soilless production system located close to the market. This study compared the growth of pea shoots using various cultivation methods in LED plant factory. The results showed that early topping (4 days after transplanting, ET) promoted early harvest compared to later topping (20 days after transplanting, LT) and increased the number of harvested shoots by extending the harvest time to 2.8 times, ultimately resulting in a substantial yield improvement. Moreover, the yield of ET with lower planting density (72 plants m-2, ET-LD) was 8.7% higher than ET with higher planting density (126 plants m-2, ET-HD). Particularly, the average fresh weight of individual pea shoots under ET-LD exceeded that of ET-HD by 48.9%. It is advisable to consider adopting ET-LD for the cultivation of pea shoots in LED plant factory. Based on ET-LD, the yield, nutritional quality, and light use efficiency of pea shoots were further explored at different stages under three levels of light intensity (50, 100, 150 μmol m-2 s-1). Contrasted against the light intensity of 50 μmol m-2 s-1, the average fresh weight per pea shoots, number of harvested, and total fresh yield under light intensity of 150 μmol m-2 s-1 treatment increased by 60.2%, 62.8%, and 165.1%, respectively. Meanwhile, the fresh weight per pea shoots, photosynthetic capacity, soluble sugar and vitamin C levels in leaves, as well as light use efficiency and photon yield, initially increased and then decreased with the extension of the planting period. Among these, soluble sugar, LUE, and PY started to decrease after reaching the maximum value at 60-70 days after transplanting. In conclusion, light intensity of 150 μmol m-2 s-1 with a photoperiod of 16 h d-1 using LEDs, combined with early topping within a planting period of 60-70 days, proves to be suitable for the hydroponic production of pea shoots in LED plant factory.

By introducing environmental mediator, for avoiding randomness in selecting indicators and subjectivity in deciding interaction path coefficients to reveal interaction mechanism among forest industry, ecology and environmental capacity, structural Pressure–State–Impact–Response (PSIR) and quantitative Structural Equation Modeling (SEM) are utilized with data on thirty–one provinces of China. We can find that: (i) forest industry has a negative influence on ecology, whereas ecology has a positive influence on industry; (ii) the destructive influence that industry has on ecology is much greater than the positive effect ecology has on industry; and (iii) environmental capacity plays a partial mediating role between industry and ecology. According to these results we can conclude that: (i) forest industry and ecology are not in a symbiotic relationship and have not reached a level of ecological security; (ii) the interaction between industry and ecology is in a period of transition from antagonistic to beneficial; and (iii) industry dominates ecology. However, we prospect the following advice: (i) methods of forest industry should be changed; (ii) new modes of industrial integration and circular economy should be developed; and (iii) the ability of the environment to sustain itself should be enhanced. The level of forest ecological security to discuss the symbiotic mechanism of industry and ecology will propose to be measured in future.

This study evaluated batch fermentation modes, namely, separate hydrolysis and fermentation (SHF), Quasi-simultaneous saccharification and fermentation (Q-SSF), and simultaneous saccharification and fermentation (SSF), and fermentation conditions, i.e., enzyme and yeast loadings, nutrient supplementation and sterilization, on high titer bioethanol production from SPORL-pretreated Douglas-fir forest residue without detoxification. The result indicated Q-SSF and SSF were obviously superior to SHF operation in terms of ethanol yield. The enzyme loading showed a strong positive correlation between enzyme loading and the ethanol yield. The nutrient supplementation and sterility was not necessary for ethanol production from SPORL-pretreated Douglas-fir. The yeast loading showed no significant influence on the ethanol yield for typical SSF conditions. The terminal ethanol titer of 43.2 g/L, or 75.1% theoretical based on glucose, mannose, and xylose theoretical was achieved when SSF was conducted at the condition of following: whole slurry solids loading of 15%, enzyme loading of 20 FPU/g glucan, 1.8 g/kg (wet) yeast loading, without nutrition supplementation and sterilization, at 38°C, on shake flask at 150 rpm for 96h. It is believed that with mechanical mixing, enzyme loading can be substantially reduced with affect ethanol yield by using a long fermentation time.

Wood is poised to become a material of choice for future construction. When appropriately managed, it is a renewable material with unique mechanical properties. Beyond its inherent sustainability, the use of wood has a crucial role in addressing climate change concerns due a significantly lower energy consumption and emissions during manufacturing and transportation, while simultaneously acting as a carbon sink. Thus, there has been a growing demand for hardwoods for structural applications, including Castanea sativa Mill., the focal point of this investigation. Albeit in a limited capacity, Eurocode 5-2 offers friction coefficients for softwoods, but it falls short for hardwoods which it is a gap to bridge with this research. These coefficients play a critical role in numerical simulations involving friction, enabling the optimization of joints and, by extension, the overall structural integrity. Test samples were evaluated at 18% moisture content, which is typical of Service Class 2, for various orientations of timber-to-timber and timber-to-steel friction. Considering previous friction coefficients at 12% moisture content, the linear variation was evaluated at an intermediate value of 15%. The results provide an experimental database for numerical simulations and highlight the influence of moisture content on the coefficients, which increase linearly along moisture percentages.

The necessity for precise and current data concerning the dynamics of land cover change in Indonesia is crucial for efforts to reduce natural vegetation cover due to agricultural expansion. The functionality of monitoring systems that incorporate Terra-MODIS is currently compromised by the limited availability of data for the immediate future. This study seeks to assess the potential of VIIRS satellite imagery in developing an early warning system for monitoring vegetation cover change in Indonesia. The Normalized Differential Open Area Index (NDOAI) computed from the 8-day’ VIIRS data was employed to detect changes in vegetation cover based on pixel-by-pixel subtraction in the NDOAI data time series. Evaluating the pixel-level accuracy of change detection is complicated due to the fact that we evaluate a change map at a coarser resolution than the Landsat-based reference map. The results revealed that increasing the threshold percentage is associated with improved accuracy. In change detection, there is often a trade-off between accuracy and sensitivity. A threshold that is too low may result in false positives, while a threshold that is too high may lead to missed changes. This study demonstrates that when a threshold value of less than 20% is applied, Landsat can identify vegetation cover changes at an earlier stage. Conversely, when a threshold value greater than 20% is employed, VIIRS will detect the change 4.5 days earlier than Landsat. Additionally, VIIRS is capable of detecting changes 25.4 days and 54.8 days faster than Landsat, respectively, when using thresholds of 40% and 75%.

The construction industry has a notable negative impact on the environment; thus, the promotion of the use of timber structures is an alternative to mitigate its effects. The research develops an artificial intelligence-based decision approach in the calculation of timber structures focused on the enhancement of the sustainability of roof structures. Based on the optimization carried out through genetic algorithms and the framework established in Eurocode 5, a general set of equations has been proposed for a laminated timber roof structure. The tool, which determines the most suitable roof structure for each strength class of laminated timber, allows for the determination of the dimensions of beams and purlins and their respective separations in order to minimize wood consumption. The ultimate goal is to offer multiple solutions regarding strength classes and structural designs in order to foster informed sustainable choices that promote efficient use of resources in construction.

Understanding morphological and genetic diversity of forest trees is essential to facilitate their conservation, sustainable management and genetic improvement for addressing the economic and environmental demands and challenges. We have examined variation in morphometric seed and pod traits and seed germination of multipurpose and widely distributed forest tree Albizia lebbek (Indian siris) from 12 provenances covering the species’ range in northern India and its relationships with bioclimatic factors. Highly significant inter-provenance variation was observed in seed size (seed length (SL), seed width (SW), SW/SL, SL×SW), seed mass (1000 seed weight), pod size (pod length (PL), pod width (PW), PW/PL), seed germination, number of seeds per pod, and insect infected seeds (IIS). The provenance effect contributed a major portion to the total phenotypic variance. Morphometric variation in all traits except for IIS was not clinal related to longitude, latitude, altitude or rainfall. There was an indication of the presence of ecotypic variation. IIS showed clinal variation with significant negative correlation with latitude. Most seed size and pod size traits showed positive correlations with several temperature bioclimatic factors and negative correlations with several precipitation bioclimatic factors. Our results have significance for genetic improvement, population genetics and genomics studies and conservation and sustainable management of A. lebbek genetic resources.

Materials engineering based on metal oxides for manipulating the solar spectrum and producing solar energy have been under intense investigation over the last years. In this work, we present NiO thin films double-doped with niobium (Nb) and nitrogen (N) as cation and anion dopants (NiO:(Nb,N)) to be used as p-type layers in all oxide transparent solar cells. The films were grown by sputtering a composite Ni-Nb target on room-temperature substrates in plasma containing 50% Ar, 25% O2 and 25% N2 gases. The existence of Nb and N dopants in the NiO structure was confirmed by the Energy Dispersive X-Ray and X-Ray Photoelectron Spectroscopy techniques. The nominally undoped NiO film, which was deposited by sputtering a Ni target and used as the reference film, was oxygen-rich, single-phase cubic NiO, having a visible transmittance of less than 20%. Upon double doping with Nb and N the visible transmittance of NiO:(Nb,N) film increased to 60%, which was further improved after thermal treatment to around 85%. The respective values of the direct band gap in the undoped and double-doped films were 3.28 eV and 3.73 eV just after deposition and 3.67 eV and 3.76 eV after thermal treatment. The changes in the properties of the films such as structural disorder, direct and indirect energy band gaps, Urbach tail states and resistivity were correlated with the incorporation of Nb and N in their structure. The thermally treated NiO:(Nb,N) film was used to form a diode with a spin-coated two-layer, mesoporous on top of a compact, TiO2 film. The NiO:(Nb,N)/TiO2 heterojunction exhibited visible transparency of around 80%, showed rectifying characteristics and the diode’s parameters were deduced using the I-V method. The diode revealed photovoltaic behavior upon illumination with UV light exhibiting a short circuit current density of 0.2 mA/cm2 and open-circuit voltage of 500 mV. Improvements of the output characteristics of the NiO:(Nb,N)/TiO2 UV-photovoltaic by proper engineering of the individual layers and device processing procedures are addressed. Transparent NiO:(Nb,N) films can be potential candidates in all-oxide ultraviolet photovoltaics for tandem solar cells, smart windows and other optoelectronic devices.

The toxic cadmium (Cd) poses a serious threat to plant growth and human health. Populus euphratica CPK21 has previously been shown to attenuate Cd toxicity by reducing Cd accumulation, enhancing antioxidant defense and improving water balance in transgenic Arabidopsis. Here, we confirmed a protein-protein interaction between PeCPK21 and AtNF-YC3 by yeast two-hybrid, HaloTag pull-down and bimolecular fluorescence complementation assays. AtNF-YC3 was induced by Cd and strongly expressed in PeCPK21-overexpressed plants. Overexpression of AtNF-YC3 in Arabidopsis reduced salt inhibition of root length, fresh weight and membrane stability under Cd stress conditions (100 µM, 7 d), suggesting that AtNF-YC3 appears to contribute to the improvement of Cd stress tolerance. AtNF-YC3 improved Cd tolerance by limiting Cd uptake and accumulation, activating antioxidant enzymes, and reducing H2O2 production under Cd stress. We conclude that PeCPK21 interacts with AtNF-YC3 to limit Cd accumulation, enhance the ROS scavenging system, and thereby positively regulate plant adaptation to Cd environments. This study highlights the interaction between PeCPK21 and AtNF-YC3 under Cd stress conditions, which can be utilized to improve Cd tolerance in higher plants.

Mangrove plant seedling cultivation is crucial for the protection, management and restoration of mangrove ecosystem. In this study, we focused on Kandelia obovata, a typical mangrove, and evaluated nursery cultivation with different combinations of three salinity levels (S1: 0 ppt, S2: 10 ppt, and S3: 20 ppt), three genealogies (EZD, JX, and YZ), and five growth media (M1: 100% loess, M2: 100% sandy, M3: 50% loess + 50% sandy, M4: 40% loess + 40% sandy + 20% peat, and M5: 40% loess + 40% sandy + 20% coir), by measuring the growth parameters such as mortality rate, seedling height, diameter, and biomass partition. These growth indexes were significantly affected by salinity and medium, and genealogies also had significant effects on mortality rate and biomass accumulation. S2 or S3 both had lower mortality and higher growth indexes than S1. M1 was the medium that increased seedlings height, diameter and biomass the most and had the lowest death rate. EZD and JX were also higher levels than YZ in these indicators, but the difference between them was not obvious. S3, M1, and EZD consistently performed well in fuzzy evaluation and quality assessment. Furthermore, combinations involving these treatments also produced highly favorable results. These results furnish both a theoretical and practical foundation for advancing nursery cultivation techniques and germplasm breeding of K. obovata in mangroves.

Forest canopy structure (CS) controls many ecosystem functions and is highly variable across landscapes, but the magnitude and scale of this variation is not well understood. We used a portable canopy lidar system to characterize variation in five categories of CS along N = 3 transects (140–800 m long) at each of six forested landscapes within the eastern USA. The cumulative coefficient of variation was calculated for subsegments of each transect to determine the point of stability for individual CS metrics. We then quantified the scale at which CS is autocorrelated using Moran’s I in an Incremental Autocorrelation analysis. All CS metrics reached stable values within 300 m but varied substantially within and among forested landscapes. A stable point of 300 m for CS metrics corresponds with the spatial extent that many ecosystem functions are measured and modeled. Additionally, CS metrics were spatially autocorrelated at 40 to 88 m, suggesting that patch scale disturbance or environmental factors drive these patterns. Our study shows CS is heterogeneous across temperate forest landscapes at the scale of 10’s of meters, requiring a resolution of this size for upscaling CS with remote sensing to large spatial scales.

Following the adoption of the Kunming-Montreal Global Biodiversity Framework (KM-GBF), with the Convention on Biological Diversity serving as its guiding treaty, the European Union (EU) has just reached an agreement on an EU Nature Restoration Regulation. This study carries out a systematic cross-walk between the restoration regulation and the KM-GBF, focusing on their implications for forest ecosystems. This paper identifies areas of alignment, divergence, and potential gaps related to habitat restoration, species protection, climate resilience, and the sustainable use of natural resources. The methodology adopts a grounded approach, starting with the 23 targets outlined in the KM-GBF and proceeding to the 28 articles set out in the restoration regulation. The results highlight the need for better alignment between the KM-GBF, the restoration regulation, and other forest-relevant EU policy instruments. The study stresses the need for a coherent and integrated EU policy approach that can address the diverse challenges and policy objectives facing forests. It concludes that amendments to the restoration regulation have significantly diluted its potential impact, limiting the EU Members States accountability and ability to meet KM-GBF goals and targets. It further stresses the need for strategies that can reconcile divergent EU policy pathways, support forest management and restoration efforts, while aligning with global biodiversity objectives.

Bone/fracture healing is a complex process with different steps and four basic tissue layers being affected: cortical bone, periosteum, fascial tissue surrounding the fracture, and bone marrow. Stem cells and their derivatives, including embryonic stem cells, induced pluripotent stem cells, mesenchymal stem cells, hematopoietic stem cells, skeletal stem cells, and multipotent stem cells, can function to artificially introduce highly regenerative cells into decrepit biological tissues and augment the healing process at the tissue level. Stem cells are molecularly and functionally indistinguishable from standard human tissues. The widespread appeal of stem cell therapy lies in its potential benefits as a therapeutic technology that, if harnessed, can be applied in clinical settings. This review aims to establish the molecular pathophysiology of bone healing, the current stem cell interventions that disrupt or augment the bone healing process, and finally, consider the future direction/therapeutic options related to stem cells and bone healing.

In the present work, an innovative range of foams, based on flax gum-filled epoxy resin was developed, reinforced or not by flax fibers. Foams and composites with different gum and epoxy resin contents were produced and characterized for mechanical and thermal performances. To enhance the organic flax gum filler's cross-linking, we exploited the oxidized components' reactivity with the amine hardener (isophorone diamine). We compared the materials obtained with those derived from the native components. Flax gum and fibers were primarily characterized by chemical analysis, NMR, and FTIR to evaluate the mild oxidation of native materials. The formation of chemical bonds between oxidized polymer chains, epoxy resin, and hardener has been evidenced by FTIR, and the materials were then studied by SEM, X-ray computed micro-tomography (CT), and submitted to mechanical and thermal tests. The relevance of oxidation treatment was highlighted, through a significant increase in density and mechanical performances (+36% and +81%, respectively for the 100% flax gum material). The positive effect of flax fibers on homogeneity evidenced through micro-CT analysis was also clearly addressed. This set of promising results paves the way for future development of fully flax-based insulation composite materials.

Abstract: Community forests are being promoted in Togo as an alternative to the degradation of protected areas and as a means of restoring forest landscapes. The present study is carried out within Kouampante Community Forest (KCF) in Ogaro (Togo, West Africa). It intends to contribute to the sustainable management of KCF. Specially, it aims at: (i) mapping forest ecosystems and analysing their dynamic and (ii) characterising the floristic diversity of the KCF. Forest ecosytems are mapped and their dynamic evaluated based on Google Earth images of 2010 and 2020. The floristic and silvicultural analyses are based on inventories carried out in 13 plots of 1,000 m² each. The KCF is made up mainly by tree/shrub savannahs (58.73%) and croplands/fallow (41.27%) in 2010. These two land use types have undergone changes over the period. In 2020, the KCF had two land use types: tree/shrub savannahs (84.30%) and croplands/fallows (15.70%). The flora census consisted of 59 species grouped in 6 families. The most important plant species are Detarium microcarpum and Vitellaria paradoxa. The Fabaceae were the most abundant and diversified families, followed by the Combretaceae. The demographic structure showed a high abundance of individuals with small diameter and height. This indicates the possibility of a rapid restoration of the native vegetation. Protecting the forest from anthropogenic threats could be crucial for achieving the desired objective.

Ecosystem physical structure, defined by the quantity and spatial distribution of biomass, influences a range of ecosystem functions. Remote sensing tools permit the non-destructive characterization of canopy and root features, potentially providing opportunities to link above- and belowground structure at fine spatial resolution in functionally meaningful ways. To test this possibility, we employed ground-based portable canopy lidar (PCL) and ground penetrating radar (GPR) along co-located transects in forested sites spanning multiple stages of ecosystem development and, consequently, of structural complexity. We examined canopy and root structural data for coherence at multiple spatial scales ≤ 10 m within each site using wavelet analysis. Forest sites varied substantially in vertical canopy and root structure, with leaf area index and root mass more evenly distributed by height and depth, respectively, as forests aged. In all sites, above- and belowground structure, characterized as mean maximum canopy height and root mass, exhibited significant coherence at a scale of 3.5-4 meters, and results suggest that the scale of coherence may increase with stand age. Our findings demonstrate that canopy and root structure are linked at characteristic spatial scales, which provides the basis to optimize scales of observation. Our study highlights the potential, and limitations, for fusing lidar and radar technologies to quantitatively couple above- and belowground ecosystem structure.

Understanding the dynamics of Organic Carbon mineralization is fundamental in forecasting biosphere to atmosphere Net Carbon Ecosystem Exchange (NEE). With this perspective, we developed 3D-CMCC-PSM, a new version of the hybrid Process Based Model 3D‐CMCC FEM where also heterotrophic respiration (R_h) is explicitly simulated. The aim was to quantify NEE as a forward problem, by subtracting Ecosystem Respiration (R_eco) to Gross Primary Productivity (GPP). To do so, we developed a simplification of the Soil Carbon dynamics routine proposed in DNDC [1]. The method calculates decomposition as a function of soil moisture, temperature, state of the organic compartments, and relative abundance of microbial pools. Given the pulse dynamics of soil respiration, we introduced modifications in some of the principal constitutive relations involved in phenology and littering sub-routines. We quantified the model structure related uncertainty in NEE, by running our training simulations over 1000 random parameter-sets extracted from parameters distributions expected from literature. 3D-CMCC-PSM predictability was tested on independent time series for 6 Fluxnet sites. The model resulted in daily and monthly estimations highly consistent with the observed time series. It showed lower predictability in Mediterranean ecosystems, suggesting that it may need further improvements in addressing evapotranspiration and water dynamics.

1) Background: We analyzed the size structure, richness and diversity in eight permanent forest plots in the upper limit of the great Amazon basin located in the Ecuadorian parts of Cordilleras del Cóndor and Cutucú. Our hypothesis was that not all the forests of the eastern mountain ranges are homogeneous in characteristics, but rather present differences in their structure, richness and floristic diversity. In order to test this, our main objective was to classify the types of forests based on characteristics in diametric structure and species composition of the Amazonian forests of the eastern cordilleras in southern Ecuador, and also to determine the influence of critical edaphic-environmental and geomorphological factors. 2) Methods: Eight one-hectare permanent plots were installed in homogeneous and well-conserved forest stands. Four plots were located in the province of Zamora Chinchipe and four in the province of Morona Santiago. We identified and measured all trees> 10 cm at diameter breast height. For each plot, soil samples were taken, along with environmental and slope data. The multidimensional non-metric adjusted scaling (NMDS) was used to evaluate changes in climatic and geomorphological gradients. The relationship between the composition of the species at the plot level and the edaphoclimatic variables was tested using a canonical correspondence analysis (CCA). Finally, we modeled the change in species diversity (Fisher's alpha) in relation to the climatic gradients, altitudinal and geomorphological using a GLMM. 3) Results: Overall, we identified 517 species belonging to 76 families. We determined the existence of two different types of forest, the first one named Terra Firme, characterized by the presence of a larger number of species and individuals per plot, compared to the second type of forest, called Tepuy or Sandstones forest. Species richness was negatively correlated with soil phosphorus content and pH, mean annual temperature, annual precipitation and altitude. The CCA analysis showed differences in the species composition between the Terra Firme and Sandstone forests. The climatic seasonality and the concentration of cations in the soil influence the diversity of the Amazon forest communities of the southeastern cordilleras. The forests of Terra Firme, which are settled in more stable and nutrient-rich climatic areas, were more diverse. Sandstone forests are poor in nutrients and develop in areas with stronger seasonality

Accurate detection of forest restoration sites using deep learning is crucial for effective ecosystem management, optimizing reforestation efforts, and ensuring environmental sustainability. While various deep learning-based systems have been developed for this purpose, the influence of different neural network architectures on model performance during the identification of forest restoration sites remains underexplored. This study aimed to address this gap by exploring the optimal methodology for extracting and classifying candidate sites for forest restoration based on Convolutional Neural Networks (CNNs), specialized for image recognition. Four categories—arable land, road and barren, quarry, and forest—were defined as candidate sites for forest restoration. A dataset comprising 17,043 samples was divided into training (11,929) and validation (5,114) sets at a ratio of 7:3 for model learning. Model accuracy was evaluated using pixel accuracy (PA) and mean intersection over union (mean IoU). The Resnet152-U-Net model demonstrated a pixel accuracy of 95.2% and a mean IoU of 61.3%, indicating excellent performance in extracting candidate sites for forest restoration. This approach offers spatial and temporal advantages over conventional field surveys or aerial image-based assessments, potentially serving as valuable data for selecting future forest restoration sites.

Objective: The goal of this review is to provide a succinct, yet comprehensive, guide to the an-tepartum management of multiple gestations. Methods: This narrative review on twins and multiple gestation provides a concise guide for providers with this ever-growing patient population. PubMED was utilized for literature search. Each reference was evaluated and graded for quality of evidence by US Preventative Services Task Force and Cochrane Review guidelines. Screening, surveillance, and management strategies are delineated succinctly and organized by type of multiple gestation being managed from the lowest risk dichorionic twin pair to the increasingly escalating risks of twins and higher order multiples sharing a placenta and/or amniotic sac. Results: The incidence of twin pregnancies has grown over the past several years, due in large part to delayed reproductive timing and surge in assisted reproductive technologies. Twin pregnancies are associated with higher morbidity for both gravidas and offspring, warranting evidence-based approach in counseling and management. Conclusions: We note the important differences among multiples in chorionicity and amnionicity, in the importance of close surveillance and early delivery. Graded clinical pearls and evi-dence-based recommendations are presented to guide obstetric providers.

Protected areas serve as an effective mechanism usually supported by a statute to conserve and protect wildlife-rich areas worldwide. Such extensive external management needs elaborate planning, regular monitoring, and periodic assessment of results. Thus, management effective evaluation (MEE) has emerged as one of the major tools for quantifying the performance of any protected area, globally since 2006. India has successfully conducted a complete round of management effectiveness evaluation of all its terrestrial protected areas (except conservation reserves and community reserves), with 25 such areas already undergoing a repeat assessment. Simultaneously, India biennially carries out a country-wide status of forest cover in all its states and union territories. This study has correlated the trend in change of forest cover for the states that contain those 25 repeat evaluated protected areas with their change in MEE scores over the same period. Our study found a positive correlation between the change in forest cover and the change in management effectiveness score from 2005-06 to 2018-19. Owing to increased protection regimes in the PAs including the degraded areas if they make part of such areas, the habitat often shows recovery. Effective habitat conservation is thus intertwined with the monitoring and preserving the wildlife populations in the protected areas, thereby, reduction in forest cover equally impacts the management scores. However, in states where the loss in forest cover has been reported, more protected areas need to be assessed to plan complementary strategies for both habitat and species conservation.

A configurable design of a microstrip square spiral RFID tag antenna, for a wide range of microwave frequencies in S- and C-band, is presented. The design is parameterized in dimensions, and hence changing the design frequency (or frequencies) is easy, by changing only an initial value for the spiral geometry. A tag specimen was fabricated using Cu electroplating technique according to the design for frequencies of interest in the areas of 2.4 and 5.8 GHz. The substrate material is a 320 μm high resistivity Si and the bridge dielectric is a 15μm polyimide PI2525. The microfabrication process involves steps of metallic structure pattern transfer techniques with optical UV lithography procedures. The reflection coefficient and gain of the specimen were measured inside an anechoic enclosure using a vector network analyzer (VNA) and a TEM horn test antenna over a frequency range of up to 6 GHz. Simulated and measured results are presented and discussed, exhibiting reasonable agreement.

Membranes are a selective barrier that allows certain species (molecules and ions) to pass through while blocking others. Some rely on size exclusion, where larger molecules get stuck while smaller ones permeate through. Others use differences in charge or polarity to attract and repel specific species. Membranes can be used to purify air and water by allowing only air and water molecules to pass through but preventing contaminants such as microorganisms and particles or to separate target gas or vapor, such as H2, CO₂, from other gases. The higher the flux and selectivity, the better a material is for membranes. The desirable performance can be tuned through material type (polymers, ceramics, and biobased materials), microstructure (porosity and tortuosity), and surface chemistry. Most membranes are made from plastic from petroleum-based resources, which contribute to global climate change and plastic pollution. Cellulose can be an alternative sustainable resource to make renewable membranes. Cellulose exists in plant cell walls as natural fibers, which can be broken down into smaller components such as cellulose fibrils, nanofibrils, nanocrystals, and cellulose macromolecules through mechanical and chemical processing. Membranes made from reassembling these particles and molecules have variable pore architecture, porosity, and separation properties and therefore have a wide range of applications in nano-, micro-, and ultrafiltration or forward osmosis. Despite their advantages, cellulose membranes face some challenges. Improving the selectivity of membranes for specific molecules often comes at the expense of permeability. The stability of cellulose membranes in harsh environments or under continuous operation needs further improvement. Research is ongoing to address these challenges and develop advanced cellulose membranes with enhanced performance. This article reviews the microstructure, fabrication methods, and potential applications of cellulose membranes, providing some critical insights into processing-structure-property relationships for current state-of-the-art cellulosic membranes that could be used to rationally improve their performance.

Retrospective information about the climate system and plant ecophysiology are key inputs in climate and Earth system modelling. Dendrochronology provides such information with large spatiotemporal coverage, and stable carbon isotope (¹³C/¹²C) analysis across tree-ring series is among the most advanced dendrochronological tools. For the past seventy years, this analysis was performed on whole molecules, and, to this day, ¹³C/¹²C variation is attributed to ¹³C discrimination during CO₂ diffusion into leaves and assimilation by rubisco. By contrast, ¹³C discrimination by post-rubisco processes is presumed constant. Here, recently reported results on the first dataset of intramolecular ¹³C discrimination in tree rings were synthesised by variance component analysis. The emerging picture is not consistent with the classical (DR-discrimination-centred) concepts and practices of carbon-isotope dendrochronology. Specifically, leaf and stem post-rubisco discrimination each account for more variation in the data than diffusion-rubisco discrimination, i.e., post-rubisco discrimination is not constant. Furthermore, diffusion-rubisco discrimination is used widely as proxy of leaf intrinsic water-use efficiency (iWUE), a key determinant in the responses of global biogeochemical cycles to climate change. However, since diffusion-rubisco discrimination is a small component of the total data variance, whole-molecule analysis yields confounded iWUE estimates, yet intramolecular analysis will likely offer solutions. Lastly, all currently observed ¹³C/¹²C-climate relationships are attributed to diffusion-rubisco discrimination. However, here, relationships with temperature and radiation derive from leaf-level post-rubisco discrimination while relationships with precipitation derive from stem-level post-rubisco discrimination. That said, advances in mass spectrometry may soon make intramolecular ¹³C/¹²C analysis broadly available taking carbon-isotope dendrochronology to the next level.

The increasingly affordable price point of terrestrial laser scanners has led to a democratization of instrument availability, but the most common low-cost instruments have yet to be compared in terms of the consistency to measure forest structural attributes. Here, we compared two low-cost terrestrial laser scanners (TLS): the Leica BLK360 and the Faro Focus 120 3D. We evaluate the instruments in terms of point cloud quality, forest inventory estimates, tree-model reconstruction, and foliage profile reconstruction. Our direct comparison of the point clouds showed reduced noise in filtered Leica data. Tree diameter and height were consistent across instruments (4.4% and 1.4% error, respectively). Volumetric tree models were less consistent across instruments, with ~29% bias, depending on model reconstruction quality. In the process of comparing foliage profiles, we conducted a sensitivity analysis of factors affecting foliage profile estimates, showing a minimal effect from instrument maximum range (for forests less than ~50 m in height) and surprisingly little impact from degraded scan resolution. Filtered unstructured TLS point clouds must be artificially re-gridded to provide accurate foliage profiles. The factors evaluated in this comparison point towards necessary considerations for future low-cost laser scanner development and application in detecting forest structural parameters.

1) Background: Neotropical montane forests represent one of the most diverse ecosystems; however, they are also the most threatened for deforestation. Our main goal is to evaluate the change in Basal Area (BA), Density and Species Composition of montane forests in the southern Ecuador and to determine the influence on some critical ecological and geomorphological factors. 2) Methods: One hundred thirty-two temporary plots of 400 m² each were installed; we identified and measured all trees> 10 cm DBH. We modeled species diversity (Fisher’s alpha) change in relation to climatic, elevational and geomorphological gradients with GLM and Kruskall-Wallis analyses. The change in composition was determined using Cluster Analyses (BIOENV analysis followed by a LINKTREE procedure). Non-metric multidimensional scaling (NMDS) was used to analyze changes across climatic and geomorphological gradients. Finally, we used SIMPER analysis to identify the species that contributed most to the dissimilarity among the different elevations. 3) Results: Formation of floristic groups was influenced by altitude, temperature and Isothermality; physiographic province, great landscape, geological landscape and lithology. Plots located in low hills have higher alpha diversity with respect to the high hills and dissected mountains. 4) Conclusions: The elevation is first hierarchical factor responsible of the division of structural and floristic groups. Plots located on the whitish tuff have a higher alpha value diversity compared with plots in andesitic tuffs. Wettest quarter (> 839 mm) and Isothermality (> 90.5) are the climatic factors that driven de floristic divisions.

ABSTRACT This study focused for socio-economic benefit of Western shoreline of Lake Ziway ecosystem. The data collected from two woredas they are Adami Tulu Jidu Kombolch (ATJK) and Dugda woreda of fishermen and small scale irrigation users. Lake Ziway great importance food and water for both groups of respondents and additionally sources of raw material, energy, cultivation, organic fertilizers, genetic and medicinal plants. Lake Ziway also has a major economic benefit for both groups of respondents. The sampled fishermen cached mean amount of 2,524Kg per year with minimum and maximum amount of fish 504Kg and 16,800Kg per year respectively and with this fish catching they got average income of 51,398 Birr ($2,570) per year with range of 7,200 Birr ($360) and 288,000 Birr ($14,400) per year. As like of fishermen small scale irrigation also got economic benefit with their production of cereal crops, fruits and vegetables. They produce in average 13.47Quintal of cereal crop and 69.56Quintal of fruits and vegetables per year and they got average income of 7,727 Birr ($386) and with range of 13,714 Birr ($686) per year respectively. this incurred that wetland ecosystem has a lot of socio-economic benefit for the people live near by specially for developing countries like Ethiopia they are more dependent on natural ecosystem like of Lake Ziway. Because of its high importance, we have to protect and conserve and use sustainably of Lake Ziway and similar wetland ecosystems. Key Words: Wetland ecosystem service; Lake Ziway; Socioeconomic benefit; Fishermen; Small scale irrigation users

The search of DNA polymorphisms useful for the genetic improvement of dairy farm animals lasts more than 40 years with relevant findings in cattle for milk traits, where the best combination of alleles for dairy processing have been found in casein genes and in the DGAT1. Nowadays, similar results are not reached yet in river buffaloes despite advanced genomic technologies and accurate phenotype records are available. The aim of the present study was to investigate and validate in a larger buffalo population the effect on six milk traits of four single nucleotide polymorphisms (SNP) in the CSN1S1, CSN3, SCD and LPL genes, previously reported to be associated with or affect dairy traits in smaller populations often belonging to one farm. A total of 800 buffaloes were genotyped. Daily milk yield (dMY, kg), protein yield (dPY, kg) and fat yields (dFY, kg), fat and protein contents (dFP, % and dPP, %), somatic cell count (SCC, 103cell/ml) and urea (mg/dl) were individually recorded in each month for the whole lactation from 2010 to 2021. A total of 15,742 individual milk test day records (2,496 lactations) were available on 680 buffalo cows with 3.6±1.7 parity (from 1 to 13) and 6.1±1.2 test day records per lactation on average. Three out four SNP in CSN1S1, CSN3 and LPL were associated with at least one of analyzed traits. In particular, the CSN1S1 (AJ005430:c.578C>T) gave favorable associations with all yield traits (dMY, p=0.022; dPY, p=0.014 ; dFY, p=0.029) and SCS (p=0.032), whereas the CSN3 (HQ677596: c.536C>T) positively associated with SCS (p=0.005) and milk urea (p=0.04). Favorable effect on dMY (p=0.028), dFP (p=0.027) and dPP (p=0.050) were observed for the LPL. Conversely, SCD did not show any association with milk traits. This is the first example of confirmation study carried out in the Mediterranean river buffalo for genes of economic interest in dairy field and it represents a very important indication for the preselection of young bulls destined to breeding programs in the view of a more sustainable dairy production.

Background: Although the link between environmental lead exposure and several patterns of cardiovascular disease (CVD) has been reported, its association with silent myocardial infarc-tion (SMI) has not been explored. We aimed to assess the association between blood lead levels (BLL) and risk of SMI. Methods: This analysis included 7283 (mean age 56.1±2.52 years, 52.5% women) participants from the Third National Health and Nutrition Examination Survey who were free of clinical CVD. Ascertainment of BLL done using graphite furnace atomic absorption spectrophotometry. SMI defined as ECG evidence of MI without history of MI. Multivariable lo-gistic regression analysis was used to examine the association between SMI and BLL. Results: SMI was detected in 120 participants corresponding to an unweighted prevalence of 1.65%. Par-ticipants with higher levels of BLL had higher prevalence of SMI (0.4%, 0.9%, and 2.4% across BLL tertiles; p-value

Rapid urbanization has changed the structure and function of natural ecosystems, especially the floodplain ecosystems in SE Asia. This paper describes the ecological structure of vegetation stands and the usefulness of satellite images to characterize a disturbed tropical urban forest located in the lower floodplain of the Chao Phraya River, Thailand. Nine representative plots were established in Bang Kachao peninsula in 4 tropical urban forest types: rehabilitation forest, home-garden agroforestry, mangrove and park. The correlation between NDVI and LAI obtained from satellite images and plant structure from field surveys were analyzed. The NDVI had the highest relationship with stand factors for the number of families, number of species, Shannon-Weiner’s diversity index and total basal area. The LAI had the highest correlation with total basal area, number of canopy layers, stand density and canopy density. Linear regression predicted the correlation between NDVI and LAI with stand factors as show above. The trend in NDVI and LAI reflected the urban forest type, being high in rehabilitation and mangrove forests, moderate in home-gardens and low in parks. Future urban planning of the Bang Kachao peninsula should focus on rehabilitation to increase the biodiversity and complexity of the urban forest.

Understory plants are important components of forest ecosystem productivity and diversity. Compared to biomass models of overstory canopy trees, few are available for understory saplings and shrubs and therefore their roles in estimation of forest carbon pools are often ignored. In this study, we harvested 24 understory species including 4 saplings, 9 tree-like shrubs and 11 typical shrubs in coniferous and broadleaved mixed forest in northeastern China and developed the best fit allometric equations of above- and below-ground and total biomass by species-specific or multispecies using morphological measurements of basal diameter, height and crown area as independent variables. The result showed that single basal diameter, height or crown area had good explanatory power for both species-specific and multispecies (p<0.001). The best-fit models included only basal diameter in sapling and tree-like shrubs, and combinations of crown area, height, and basal diameter in typical shrubs. The logarithmic model was most desired among the 4 model forms of linear, quadratic, multiple linear and logarithmic, for species-specific and multispecies. The models we developed should help the estimation of forest ecosystem carbon stocks, especially for belowground component, and provide tools for quantification of individual species biomass of understory plants.

Sixteen crossbred rabbits (New Zealand white x Thai native breed) were randomly divided into two groups of eight to determine the effects of daily oral administration of crude extracts from the butterfly pea (Clitoria ternatea L.) from weaning (at 35 days) to slaughter (at 90 days). Effects on phagocytic activity of blood polymorphoneuclear leukocytes, serum biochemistry, meat quality, muscular lipid peroxidation, apparent digestibility, and gut histology were studied. The results revealed that the phagocytic function of circulating leukocytes (75 and 90 days) and alveolar macrophages (90 days) did not differ between the two groups. At slaughter, treated rabbits had lower blood urea nitrogen concentrations and higher liver weight than control rabbits (p &lt; 0.05). After chilling at 4°C for 24 hours, lower meat pH and alteration of meat color (a brighter, less yellow, Hue angle and color saturation) were observed in the treated group (p &lt; 0.05). Furthermore, lipid peroxidation (measured at 3, 5 and 7 storage days) in the meat of treated rabbits was lower than in controls (p &lt; 0.05). Apparent digestibility (analyzed at 46 days for four days) revealed improved organic matter and ether extracts in the treated group (p &lt; 0.05), whereas gut histology was unaffected. In conclusion, butterfly pea extract supplementation did not affect phagocytic function but led to a modification in meat color, delayed lipid peroxidation, and improved digestibility.

The natural vegetation study was conducted in Kafta-sheraro national park (KSNP) North, Ethiopia to explore floristic composition, structure and regeneration of woody species in the home of African elephant. In the park, the above information is not well documented which is necessary for conservation. Data were collected From August to December 2018. The vegetation data were collected from 161 quadrats of size 20m×20m, 5mx5m for shrub ̸ tree, sapling and seedling respectively. Individual trees and shrubs DBH >=2.5cm and height >=2m were measured using Tape meter and Clinometer respectively. DBH, frequency, density, basal area, and IVI were used for vegetation structure. A total of 70 woody species 46 (65.7%) trees, 18 (25.7%) shrubs and 6 (8.6%) tree ̸ shrub) were identified. The total basal area and density of 79.3 m2 ha-1, and 466 ±12.8 (S.E.) individuals ha-1 were calculated for 64 woody species. Fabaceae was the most dominant family occupied 16 species (23.0%) followed by Combretaceae 8 species (11.4%). Acacia mellifera and Combretum hartmannianum were the most dominant and frequent species. Abnormal patterns of selected woody species were dominantly identified. Regenerating status all the woody plant species was categorized as “Fair” (18.75%), “Poor” (7.81 %) and “None” (73.44%). However, there is good initiation for conservation of the park; still the vegetation of the park was threatened by firewood collection, charcoal production, fire, intensive farming, mining and over grazing. Therefore, the study area as the habitat for the population of the African elephant; the KSNP should be recommended the highest conservation priority and studied the soil seed bank of species having poor regeneration condition.

Poplars (Populus spp.) are of significant ecological and economic importance. Long-term breeding efforts were aimed mainly at obtaining fast-growing and productive plants and less considered resistance to pests. This study aimed to identify the patterns of susceptibility to Saperda carcharias (Linnaeus, 1758) (Coleoptera: Cerambycidae) among Populus hybrids and pure species, considering crossing combinations and some other traits. In our research, 35 clones of poplar species and hybrids of the Ukrainian and foreign selection from the Aigeiros, Tacamahaca, and Leucoides sections were tested in 2021 and 2023 in the plantation created in 2014 in Eastern Ukraine. S. carcharias preferred infesting clones with earlier foliage development, larger diameters, and height increments. Specifically, hybrids with American maternal lineage showed the highest susceptibility, whereas those with European maternal lineage or Asian origin displayed lower infestation levels or resistance, respectively. This variability suggests a complex relationship between genetic background and pest resistance, underlining the need for a deeper understanding of the factors influencing susceptibility to S. carcharias. Selecting native species clones or creating mixed clone plantations could enhance the resilience of poplar plantations to pest threats.

The Himalaya is well known for high diversity and ethnobotanical uses of medicinal plants. However, not all areas of the Himalayas are well studied. In particular, studies on ethnobotanical uses of plants from the Eastern Himalayas are rare and lacking for many tribes. Past studies primarily focused on listing plants name and their traditional medicinal uses. However, studies on traditional ethnopharmacological practices on medicine preparation had not yet been reported in published literature from the Eastern Himalaya. In this study, we are reporting the first time ethnopharmacological used 24 medicines, their procedures of preparation and listed 53 plant species used for those medicines for Monpa tribe. Such documentations had not yet been done for other tribes in India. Our research demonstrates the urgent need to documents traditional medicine preparation procedures from the local healers before rapid cultural modernization forgets them in transforming country like India. This study should motivate national and international researchers to do more works on ethnopharmacology and bioprospecting.

Background: Subclinical myocardial injury (SCMI) is associated with an increased risk of poor cardiovascular disease (CVD) outcomes. Understanding the underlying risk factors for SCMI is crucial for the prevention and management of CVD. We hypothesized that atherogenic dyslipidemia, a combination of high triglycerides (TG) and low high-density lipoprotein cholesterol (HDL-C), is associated with an increased risk of SCMI. Methods: This analysis from the third National Health and Nutrition Examination Survey (NHANES-III) included 7,093 participants (age 59.3±13.4 years, 52.8% women, and 49.4% White) free of CVD. Atherogenic dyslipidemia was defined as TG ≥150 mg/dL and HDL-C <40 mg/dL in men or <50 mg/dL in women. A validated electrocardiographic-based cardiac infarction injury score (CIIS) ≥10 was considered positive for SCMI. Multivariable logistic regression analysis was used to examine the association of different combinations of TG and HDL-C groups, including atherogenic dyslipidemia with SCMI. Results: About 22.5% (n=1,594) of participants had atherogenic dyslipidemia, and 26.3% (n=1862) had SCMI. Compared to participants with normal TG and normal HDL-C, those with atherogenic dyslipidemia had a higher prevalence of SCMI (31.2% vs. 23.9%, p-value <0.001). In a multivariable logistic regression model, atherogenic dyslipidemia was associated with the highest odds of SCMI followed by high TG/normal HDL-C, then low HDL-C/normal TG [OR (95% CI): 131 (1.14,1.52), 1.13 (0.97,1.33), and 1.01(0.86,1.20), respectively). Conclusions: Atherogenic dyslipidemia is associated with a higher risk of SCMI, which highlights the role of nontraditional risk factors in the development of subclinical CVD.

Despite of being an exceptionally biodiversity rich country, the forest coverage of Bangladesh is declining at an alarming rate. Declaration and management of protected areas in this regard is one of the efforts from government side to tackle the loss of biodiversity. The limited numbers of forest-protected areas (FPA), established to conserve the dwindling forest biodiversity of the country with high pressure on them for timber, non-timber forest products, and fuelwood - makes their management challenging. Moreover, most of the FPAs of the country declared only in the recent decades with very limited infrastructure, manpower and policy support for monitoring and governance. Some people-centred approaches for the management of FPAs and alternative livelihood and income generation subsidies although made available through a few project interventions, their number are still inadequate and performance remains less than satisfactory. This chapter provides a critical review of the FPAs of Bangladesh looking at their role in biodiversity conservation, management challenges, and key lessons from previous management interventions with recommendations for the future. It has been revealed that the FPA system of Bangladesh still poorly represents the diverse forest ecosystems with relatively small forest size and lack of corridors for the movement of wildlife. There are ample opportunities to render co-management of FPAs an effective strategy to minimize the conflicts in FPAs management in the country. It is, however, important to ensure the access of local forest-dependent people to different alternative income generating options that may adequately support their livelihoods.

Quaking aspen (Populus tremuloides Michx.) is an important deciduous species in western U.S. forests. Existing maps of aspen distribution are based on Landsat imagery and often miss small stands (&lt;0.09 ha or 30 m²), which rapidly regrow when managed or following disturbance. In this study, we present methods for deriving a new regional map of aspen forests using one year of Sentinel-1 (S1) and Sentinel-2 (S2) imagery in Google Earth Engine. We assessed the annual phenology of aspen in the Southern Rockies and leveraged the frequent temporal resolution of S1 and S2 to create ecologically relevant seasonal composites. Additionally, we derived spectral indices and radar textural features targeting the canopy structure, moisture, and chlorophyll content. Using spatial block cross-validation and Random Forests, we assessed the accuracy of different scenarios and selected the best performing set of features for classification. Comparisons were then made with existing landcover products across the study region. The resulting map improves on existing landcover products in both accuracy (average F1-score = 93.1%) and detection of smaller forest patches. These methods enable accurate mapping at spatial and temporal scales relevant to forest management for one of the most widely distributed tree species in North America.

The criteria of “Distinctness, Uniformity and Stability” as well as a high "overall quality index” are used to register the Italian modern varieties to the national register. Differently, local conservation varieties can be certified under different EU Directives having, as overall objective, the preservation of biodiversity and the containment of genetic erosion. In recent years, products derived from an-cient grains are perceived to be healthier and more sustainable by consumer, especially in Italy, with consequent higher market prices. Ancient tetraploid wheat varieties registered in the national reg-ister of conservation varieties are 28, 24 of which are Sicilian. They are supposed to have a wide genetic variability compared to modern ones, making them vulnerable of fraud because they are difficult to trace. It is therefore important to have tools able to discriminate the autochthonous Si-cilian varieties. This can be done by gluten proteins composition, which also gives information on the technological properties of derived products. Fifty-one accessions belonging to 22 ancient va-rieties of Sicilian tetraploid (mostly durum) wheat were analyzed. Although a wide intra-accession and intra-varietal variability was assessed, the gliadin pattern of bulks of seeds belonging to each variety was discriminatory. Moreover, differences in technological attitudes were found between landraces. This paves the way to use gluten protein patterns for traceability allowing local farmers and producers to valorize their products and assure consumers about the transparency of the entire supply chain.

The article presents a model for optimizing biomass supply chains using the linear programming framework integrated with a Geographic Information System. Based on the distance from a given type of biomass resource, its calorific value, price, and transportation costs, the model identifies the optimal source of biomass, allowing it to cover the demand for the required total energy value with the lowest possible costs. The case study includes the Połaniec power plant in southeastern Poland and potential sources of forest biomass and agricultural straw within 100 km of the plant. Unit costs of biomass varied depending on biomass availability and energy demands. For energy demand on the level of 1 PJ yearly, the lowest unit costs of biomass (4.08 €/MJ) were when all kinds of biomass were available, and the highest (5.47 €/MJ) was when only stacked wood was available. As energy demand increased, unit costs increased, and the ability to meet this demand with just one type of biomass decreased. The energy biomass sector can utilize the model to benefit both biomass producers and their final buyers.

Landscape configuration and forest structure assume an increasing importance as determinants of animal communities. This paper focused on nocturnal lepidoptera inhabiting alder patches in the Sila National Park, Italy. According to their shape, patches were divided into linear and compact ones to disentangle the role of forest structure and landscape configuration in determining the composition of nocturnal lepidopteran communities at different observation scales. We used the Mann-Whitney test for medians to Shannon diversity, Equitability, Fisher’s alpha, and nestedness to test differences among moth communities. We found that compact patches inhabit richer and more abundant communities. The abundance-based Correspondence Analysis showed moth communities clustered according to woodlot shape, except a compact woodlot having a linear-like moth community because entirely surrounded by grasslands. Percentage of forested area and abundance and composition of communities are positively correlated at 50 and 200 m buffers, while correlations are absent at smaller and larger buffers. Our results demonstrated that a width of 50 m may not be sufficient to give proper functionality to the wooded area, at least for moths. As consequence, planning of forest restorations should consider the importance to increase structural habitat continuity at larger scales.

Chaga (Inonotus obliquus) is a pathogenic fungus that grows mostly on birch species (Betula pendula and B. pubescens) and has traditionally been used as an anti-cancer medicine. The study aimed to compare the chemical composition and cytotoxic activity of chagas growing on both Betula spp. on various cancer cell lines. The freeze dried extracts contained triterpenes inotodiol, lanosterol betulin and betulinic acid typical to conks growing on Betula species. The cytotoxic activity of chaga growing on Betula pendula and B. pubescens 80% ethanolic extracts against thirty-one human cancer cell lines has been evaluated by a sulforhodamine B assay. The strongest inhibitions were observed with chaga (growing on B. pendula) extract on the HepG2 and CAL-62 cell line, and with chaga (from B. pubescens) extract on HepG2 cell line, with IC50 values of 37.71, 43.30, and 49.99 μg/mL, respectively. The chaga extracts from B. pendula exert somewhat stronger effects on most cancer cell lines studied than B. pubescens extracts. This study highlight the potential of chaga as a source of bioactive compounds with selective anti-cancer properties, encouraging further exploration of its therapeutic mechanisms and potential applications in cancer treatment.

As a precious natural resource, forests are being destroyed. In previous studies, there is a lack of interactive assessment of its distribution that comprehensively considers multiple external disturbances. This paper takes the Barcelona Metropolitan Region as an example. Based on remote sensing, it analyzes the development process of the forest from 2006 to 2018 through multiple landscape indicators, and OLS models were established to analyze variables that have direct and indirect effects on forest distribution. In addition, the ecological structure of the forest was analyzed based on NDVI. It was found that the forest area is the largest but has been decreasing, becoming more complex in distribution structure. Much of the forest was converted to agricultural land and grassland. The green quality of forests was increasing, and the broad-leaved forest, the second largest area, contributes the most. NDVI is the most important positively correlated variable, and daytime surface temperature is an important inverse factor related to NDVI. In addition, NDBI is also a negative condition that inhibits forest development. In conclusion: The BMR forest area is decreasing and becoming more fragmented. NDVI and daytime LST are the two most significant factors. Climate warming may lead to worse forest development.

Soil organic matter (SOM) is essential for nutrient cycling and soil carbon (C) accumu-lation, both of which are heavily influenced by the quality and quantity of plant litter. Since SOM dynamics in relation to plant diversity are poorly understood we investigated the effects of willow variety and mixture, and site on the soil C stocks, SOM chemical composition and ther-mal stability. Using pyrolysis-field ionization mass spectrometry we analysed the top 10 cm of soil from two 7-year-old experimental sites in Germany and Sweden, with monocultures and mixtures of two willow varieties (Salix spp.) belonging to different species. Overall, site had the strongest effect on SOM quality. Results showed significant variability across sites for willow identity and mixture effects on C accumulation and SOM chemistry. In the German site (Ros-tock), yearly soil C accumulation was higher (p < 0.05) for variety ‘Loden’ (1.0 Mg C ha-1 year-1) compared to ‘Tora’ (0.5 Mg C ha-1 year-1), whilst in the Swedish site (Uppsala), both varieties ex-hibited similar soil C accumulation rates of around 0.6 Mg C ha-1 year-1. Willow variety identity significantly affected SOM quality at both sites, while mixing had minor effects. Our findings emphasize the significance of site-specific context and variety or species identity in shaping soil C accumulation in willow plantations.

Savannas and adjacent vegetation types like gallery forests are highly valuable ecosystems contributing to several ecosystem services including carbon budgeting. Financial mechanisms such as REDD+ have provided an opportunity for developing countries to alleviate poverty through conservation of its forestry resources. For availing this opportunity carbon stock assessments are essential. Therefore, a research study at two protected areas i.e. Nazinga Game Ranch and Bontioli Nature Reserve, in Burkina Faso was conducted with the objective of assessing carbon Mg C ha-1 in aboveground biomass (AGB)dry of trees in different formations of the south-sudanian savanna in Burkina Faso, West Africa. Similarly analysis of various vegetation parameters was also conducted to understand the overall vegetation structure of these two protected areas. For estimating AGBdry, existing allometric equation for dry tropical woody vegetation types was used. The Importance Value Index (IVI) and Family Importance Value (FIV) were estimated through standard procedures. Various linear and non-linear regression analyses were conducted to test the relationships between carbon and other parameters such as DBH, height and basal area (BA). The results showed that both sites collectively contain mean carbon of 3.41 ± 4.98 Mg C ha-1. Amongst different vegetation types, gallery forests recorded the highest mean carbon of 9.38 ± 6.90 Mg C ha-1. The highest IVI of 115.56 at Nazinga Game Ranch was recorded for Anogeissus leiocarpa. Similarly, highest IVI of 98.59 was recorded for Mitragyna inermis at Bontioli Nature Reserve. The highest FIV was recorded for Combretaceae for both of the sites. To our knowledge, this was the first study conducted to assess the carbon stocks at the two protected areas in southern Burkina Faso. The study therefore was an attempt for addressing the knowledge gap particularly on carbon stocks of protected savannas. It could serve as a baseline for carbon stocks for future initiatives such as payment for environmental services and REDD+ at these areas.

In contemporary construction, the prevalence of vibration serviceability issues in lightweight and slender structures has become increasingly common, owing to advancements in building materials and construction methods. While these structures often meet the criteria for ultimate limit states, they can still elicit complaints due to excessive vibrations induced by human activity. To address this challenge, the Integral Resonant Control (IRC) technique has emerged as a favored approach for actively damping vibrations in various systems. This study introduces a fresh perspective on implementing a multi-input multi-output (MIMO) IRC scheme for active vibration control (AVC) specifically tailored for pedestrian structures utilizing inertial mass actuators. Building upon a common framework and design methodology outlined in previous research, this work presents a novel application of MIMO IRC for AVC. The designed controller is rigorously tested and implemented on a laboratory floor structure to validate its efficacy.

(1) Background: Artificial intelligence (AI) has existed in some form for decades, but recent rapid advances in a subset called machine learning (ML) — and more specifically deep learning (DL), a neural network-based approach — have made headlines for the potential to revolutionize and automate multiple large sectors of society, including scientific research and the healthcare field. Furthermore, large language models (LLMs) — which are built on DL — could lead to a more seamless, natural interaction between humans and computers. (2) Methods: We reviewed numerous publications on this subject from recent years. (3) Results: We found these studies collectively show that AI is positively disrupting both biomedical research and medical practice, such as optical imaging in surgery guidance. (4) Conclusions: However, we recommend caution in over-reliance on AI in the laboratory or the clinic due to anticipated risks and current limitations.

Human activities (e.g., exploitation, utilization, and conservation) exert substantial impact on forest ecological functions (FEF). The human influence on FEF significantly varies across developmental stages, which are attributed to the temporal and spatial in nature. This study evaluates some notable FEF indices (FEFI) in the 448 counties within the Yellow River basin (YRB) using panel data from the Seventh to Ninth National Forest Inventory. Data analysis involves employing the residual trends, geographical and temporal weighted regression. Results indicate that, firstly, the overall forest ecological function in the YRB is moderate to inferior, with superior FEF in counties endowed with more natural forest resources. Afforestation demonstrates a short-term improvement, but its effectiveness diminishes over time. Secondly, the positive spatial correlation is stronger among counties, characterized by both high-high and low-low agglomeration effects. Scattered planting, simple stand structure, and concentrated harvesting of forests at the identical stand ages hinder the formation of complex and large-scale FEF agglomerations. Thirdly, significant spatial-temporal differences exist in the impact of human activities on FEF. In the upper reaches of the basin, increased vegetation coverage through agricultural and forestry production benefited FEF, however, some over-exploitation of forests and grasslands is observed there. In the middle reaches, the economic development, expanding population and the greening activities help to improve FEF effectively, but excessive water using in agricultural production brought more difficulties to FEF improvement. In the lower reaches of the basin, improved wastelands and forest protection positively influence FEF. This study recommends that county governments should prioritize forest management with multi-species and multi-layered complex forests. Each county should define its position in regional development and ecological protection, considering the potential impacts on neighboring regions. This holistic approach promotes more effective integrated regional management.

The forest regeneration phase in Sweden commonly involves mechanical soil preparation followed by planting of Scots pine or Norway spruce seedlings. The prepared soil offers planting positions with different properties, including decreased damage by pine weevil (Hylobius abietis L.). Nitrogen fertilization can be applied at the time of planting to aid establishment of the seedlings. In this study we compared the effect of organic nitrogen-fertilization for different planting positions, and seedling sizes on early survival and growth of Scots pine and Norway spruce seedlings. The main planting positions were capped mound, hinge, and mineral soil. Seedlings planted close to organic material were categorized as “low quality positions”, since proximity to organic material increase pine weevil attraction. Higher mortality rates related to pine weevil damage were recorded for seedlings planted in the low-quality positions, regardless of seedling size or N-fertilization. Pine weevil attack rates increased with increasing seedling size. Growth was in general lowest in mineral soil positions. The effect of organic N-fertilization on growth was positive for spruce regardless of planting positions and seedling size, while depending on planting position and seedling size for pine, indicating that effects of organic N-fertilization depend on seedling species, -size and planting position.

Keywords: Forest ecosystem; Biodiversity; Ecosystem multifunctionality

Ambrosia trifida is a kind of malignant invasive plant, which has very high reproductive and en-vironmental adaptability. Through strong resource acquisition ability and allelopathy, it could inhibit the growth and reproduction of surrounding plants, destroy the stability of an invasive ecosystem. It is very important to predict the change of suitable distribution area of Ambrosia trifida with climate change before implementing scientific control measures. Based on 106 Ambrosia trifida distribution data and 14 environmental data, the optimal parameter combination (RM = 0.1, FC = LQ) was obtained by using the MaxEnt model optimized by Kuenm package, the potential suit-able areas of Ambrosia trifida in Northeast China under three different climate scenarios (RCP2.6, RCP4.5, RCP8.5) with different emission intensities in the future (2050,2070) were predicted. The changes of Ambrosia trifida suitable area in Northeast China under three climate scenarios were compared, and the relationship between the change of suitable area and emission intensity was analyzed. In general, the suitable area of Ambrosia trifida in Northeast China will expand gradually in the future, and the area of its highly suitable area will also increase with the increasing emission intensity, which is unfavorable to the control of Ambrosia trifida.

With the burgeoning growth of online retail, the issue of counterfeit products has become a significant threat to both consumer trust and brand integrity, posing challenges to sustainable market practices. Online retail platforms are promoted to redesign their channel structures and enhance brand traceability to tackle counterfeits using blockchain technology. To investigate the interactions between blockchain technology and the channel structures of online retail platforms, we design a game theory model incorporating a manufacturer with(out) blockchain participation selling products via an online retail platform that operates an agency channel and/or a reselling channel. We show that the critical trade-off of blockchain participation comprises the brand assurance effect of the blockchain, the channel competition intensification effect, and the blockchain adoption cost. The platform is capable of strategically designing the channel structure to encourage (while discouraging) blockchain participation by the manufacturer. Our analysis highlights the complementarity between blockchain participation and the channel structure. Furthermore, the effect of the consumer’s belief in the reselling channel, the commission fee in the agency channel, and the substitutability between channels are investigated in depth. The research provides valuable insights for online retail platforms and policymakers seeking to foster a sustainable and trustworthy e-commerce ecosystem.

This article explores the cutting-edge advancement of gypsum and cement building boards infused with shape-stabilized n-octadecane, an organic phase change material (PCM). The primary focus is on improving energy efficiency and providing electromagnetic interference (EMI) shielding capabilities for contemporary buildings. The research investigates the integration of these materials into construction materials, using red-mud Carbon Foam as a stabilizer for n-octadecane (OD@CCF). Various analyses, including microstructural examination, porosity assessment, and additive dispersion, were conducted using X-ray microtomography and density measurements. Thermal conductivity measurements demonstrated the enhancement of composite boards as the OD@CCF content increased, while mechanical tests indicated an optimal additive content of up to 20%. The thermal-regulated capabilities of these advanced panels were evaluated in a custom-designed room model equipped with a homemade environmental chamber, illustrating a consistent temperature environment during heating and cooling cycles. The incorporation of OD@CCF into cement boards exhibited improved thermal energy storage properties. Moreover, the examined composite boards displayed efficient electromagnetic shielding performance within the frequency range of 3.2–7.0 GHz, achieving EMI values of approximately 18 and 19.5 dB for gypsum and cement boards, respectively, meeting the entry-level value required for commercial applications.

Conventional monitoring relies on "in vivo" (non-destructive) measurements of aboveground organ traits (such as stems, branches, and leaves) to analyze plantation growth trends and assess the effectiveness of management practices like watering and fertilization. This study reveals the necessity of “ex vivo” (destructive) approaches, post-excavation, to ensure fully reliable monitoring of plantation performance, including belowground organ growth and development trends. We showcase the effectiveness of dendrometric analysis, which measures the annual ring width in the secondary xylem (wood) of the taproot and stem. Monitoring above- and belowground organ growth trends allow for the exploration of similarities and differences in how different tree organs respond to internal and external factors. Such monitoring is especially crucial for assessing plantation performance in challenging climates, such as those found in arid and semi-arid lands.

Vibration signal analysis is regarded as a fundamental approach in diagnosing faults in rolling bearings, and recent advancements have shown notable progress in this domain. However, the presence of substantial background noise often results in the masking of these fault signals, posing a significant challenge for researchers. In response, an Adaptive Denoising Autoencoder (ADAE) approach is proposed in this paper. The data representations are learned by the encoder through convolutional layers, while the data reconstruction is performed by the decoder using deconvolutional layers. Both the encoder and decoder incorporate adaptive shrinkage units to simulate denoising functions, effectively removing interfering information while preserving sensitive fault features. Additionally, dropout regularization is applied to sparsify the network and prevent overfitting, thereby enhancing the overall expressive power of the model. To further enhance ADAE's noise resistance, shortcut connections are added. Evaluation using publicly available datasets under scenarios with known and unknown noise demonstrates that ADAE effectively enhances the signal-to-noise ratio in strongly noisy backgrounds, facilitating accurate diagnosis of faults in rolling bearings.

The wellness economy has developed rapidly recently, particularly in wellness tourism. Wellness tourism transforms sustainable strategy through the availability of extended multi-actor engagement in service innovation to further the tourism experience. Therefore, when operating a wellness tourism destination, it is necessary to encourage multi-actor engagement in service innovation to achieve sustainable development. This paper introduces a mixed research method with the SWOT-AHP-QSPM, as it qualitatively analyzes the advantages, disadvantages, opportunities, and threats, constructs an evaluation index system, conducts quantitative analysis using the analytic hierarchy process, determines the index weight and weighted score, and calculate the sustainable development strategy, which is appropriate for wellness development of Chongqing Tea Mountain and Bamboo Forest National Forest Park. Purposive field surveys and personal interviews were conducted in Chongqing forest tourism destinations, involving 356 effective respondents. The research reveals that multi-actor engagement significantly enhances sustainable development. These findings bridge service innovation knowledge gaps and provide valuable insights for forest tourism destination management and sustainable policy strategies to elevate multi-actor engagement in forest sites.

: This study aimed to validate the effects of self-compassion-based forest healing therapy as an intervention for reducing stress and promoting coping resources. Therefore, we investigated the effects of self-compassion-based forest healing therapy on stress, self-compassion, and connectedness to nature. A total of 30 participants were divided into an experimental and control group. Two sessions of forest healing meditation activities were held at the Forest of Healing every two weeks between October and November 2023. As a repeated measures experiment, data were collected before the intervention, after the first intervention, and after the second intervention. Perceived stress, positive and negative affect, and salivary cortisol were measured to assess physiological and psychological stress in participants. Connectedness to nature and self-compassion were measured to evaluate stress-coping resources. The results showed that the forest healing program had significant positive effects on stress and emotional states in the experimental group after the intervention. Further, there was a significant incremental effect on connectedness to nature and self-compassion in the experimental group. Therefore, self-compassion meditation-based forest healing therapy is a feasible and efficient approach for facilitating stress management and coping resource building.

In this work, we introduce the first pipeline that combines a refraction-aware Structure-from-Motion (SfM) method with a deep learning model specifically designed for airborne bathymetry. We accurately estimate the 3D positions of the submerged points by integrating refraction geometry within the SfM optimization problem. This way, no refraction correction as post-processing is required. Experiments with simulated data that approach the real-world capturing conditions demonstrate that SfM with refraction correction is extremely accurate, with submillimeter errors. We integrate our refraction-aware SfM within a deep learning framework that also takes into account radiometrical information, developing a combined spectral and geometry-based approach, with further improvements on accuracy and robustness to different seafloor types, both textured and textureless. We conducted experiments with real-world data at 2 locations in the southern Mediterranean Sea, with varying seafloor types which demonstrate the benefits of refraction correction for the deep learning framework. We open-source our refraction-aware SfM, providing researchers in airborne bathymetry with a practical tool to apply SfM in shallow water areas.

Telecoupling, interactions between social-ecological systems across large, often global, distances, drives negative impacts from the forest-based carbon market. Yet, these negative impacts have been underreported; and therefore, likely vastly underestimated. We identify how these unintended negative impacts may occur and provide recommendations for the forest-based carbon market to better account for externalities by prioritising positive social impact, expanding comprehensive ecological outcomes and improving transparency of investments. We call for a carbon market that is designed to account for its global interconnectedness.

By using the particle swarm optimization algorithm for crystal structure prediction, we reveal a newly orthorhombic Cmcm structure of HfB4, which is more energetically superior to the previously proposed YB4-, ReP4-, FeB4-, CrB4-, and MnB4-type structures in the considered pressure range. The phonon dispersion and elastic constants calculations confirm that the new phase is dynamically and mechanically stable. The calculated large shear modulus (240 GPa) and high hardness (45.7 GPa) imply that the predicted Cmcm-HfB4 is a potential superhard material. Meanwhile, the directional dependences of the Young's modulus, bulk modulus, and shear modulus for HfB4 are systematically investigated. Further analyses of the density of states and electronic localization function indicate that the strong B-B and B-Hf covalent bonds greatly contribute to its high hardness and stability.

In Mexico there is a deficit in the production of pine resin, because it depends on natural forests. Therefore, it is necessary to select provenances and phenotypes of potential species such as P. oocarpa. The objective was to determine the difference between provenances and the variation of resin components and quality, as well as the effect of geographic and climatic factors. Resin from five provenances was collected from southern Mexico. The percentage of rosin, turpentine and water was obtained, as well as the acidity and saponification index. P. oocarpa resin had 80.94 % rosin, 7.7 % turpentine and 11.49 % water. The saponification and acidity index was 125.47 and 117.49 mg KOH.g_1, respectively. All variables showed differences (p≤ 0.0001) between provenances. The provenance contributed between 6.44 and 11.71 % to the total variance, the error contributed between 88.29 and 93.56 %. Geographic and climatic variables only had an effect on the percentage of turpentine; the correlation was negative with altitude and longitude, but positive with temperature and precipitation. The results allow defining seed collection sites for resin plantations and orienting the selection for a P. oocarpa improvement program.

Forests have multifunctional roles. They not only increase forest carbon sinks through afforestation and management, but also indirectly realize multiple benefits of "economy + ecology + society". Therefore, we construct a multiple output-benefit system of forest carbon sinks based on the development of forest carbon sinks in provinces of China. This system is also able to distinguish the importance of forest carbon sinks from other outputs. For the efficiency evaluation of multi-level output systems, this paper constructs a cross-evaluation model based on evidential reasoning method, the original efficiency information by conducting efficiency evaluation before information fusion. Further, the spillover effects and influencing factors of forest carbon sink efficiency are analyzed through a spatial regression model to explore the spatial characteristics of forest carbon sink efficiency in China. The results show that: (1) there is a large gap between the cross-efficiency levels of forest carbon sinks in various regions of China, with significant spatial correlation. For the perspective of direct output benefits, the cross-efficiency of the eastern region is higher, while the cross-efficiency of the northwestern region is lower; for the perspective of indirect output benefits, the cross-efficiency of the southeastern region is higher. (2) China's forest carbon sink has a significant positive spillover effect, and the indirect output cross-efficiency has a significant negative impact on the forest carbon sink in its own region. Further analyzing the impact of indirect output cross-efficiency, it is found that the cross-efficiency of the ecological dimension and the cross-efficiency of the social dimension have a significant negative impact on the forest carbon sink in its own region, and the economic dimension has a significant positive impact on the forest carbon sink in its own region. In conclusion, corresponding policy recommendations are proposed for the development of forest carbon sinks to promote the realization of the dual-carbon goal.

Coppicing has been neglected in recent decades leaving gaps in knowledge on silvicultural interventions, especially the long-term effects on coppices of South-East Europe. Thus, our work aims to define the long-term effects of thinning in sessile oak (Quercus petraea (Matt.) Liebl.) and European beech (Fagus sylvatica L.) sub-mountainous thermophilic low coppices in the Croatian Dinarides. The experiment includes two localities with thinning plots and control plots. Thinning was done in 2002 with 17.71% of wood volume removed in the European beech coppice and 26.09% in the sessile oak coppice. 1276 trees were marked, measured (DBH, tree height, number of stems per stump) and assessed for vitality, origin and six silvicultural features revealing tree quality. Descriptive statistics for all variables, RMANOVA for DBH and height and for continuous variables mean+-+ standard deviation for categorical frequency and relative frequency variables were carried out. The results show a statistically significant positive long-term effect of thinning on tree growth, stem and crown features and support findings that thinning, by increasing growth and quality, is a necessary intervention in European beech and sessile oak low coppices. The recent economic crisis, the sudden increase in energy prices, and the increased demand for assorted wood products have initiated higher interest in coppices in Croatia.

The SK model proposed by Sherrington and Kirkpatrick is an important mean field model for spin glasses. The dependence structure of Hamiltonians of the SK model is considered in this paper. We have investigated the covariance matrix of Hamiltonians of the SK model, and establish a relationship between the rank of the corresponding covariance matrix and the dimension of the space spanned by the Hamiltonians. Finally, we also give an upper bound for the rank of the covariance matrix, which might be the best.

Estimating the ocean’s subsurface thermohaline information from satellite measurements is essential for understanding ocean dynamics and El Niño phenomenon. This paper proposes an improved double-output Residual Neural Network (DO-ResNet) model to concurrently estimate the ocean subsurface temperature (OST) and ocean subsurface salinity (OSS) in the tropical Western Pacific using multi-source remote sensing data, including sea surface temperature (SST), sea surface salinity (SSS), sea surface height anomaly(SSHA), sea surface wind (SSW), and geographical information (including longitude (LON) and latitude (LAT)). In the model experiment, Argo data were used to train and validate the model, and the root mean square error (RMSE), normalized root mean square error (NRMSE) and coefficient of determination (R²) were employed to evaluate the model's performance. The results showed that the sea surface parameters selected in this study have a positive effect on the estimation process, and the average RMSE and R² values for estimating OST (OSS) by the proposed model are 0.34 °C (0.05 psu) and 0.91 (0.95), respectively. Under the data conditions considered in this study, DO-ResNet demonstrates superior performance relative to the extreme gradient boosting model, random forest model, and artificial neural network model. Additionally, this study evaluates the model’s accuracy by comparing its estimations of OST and OSS across different depths with Argo-derived data, demonstrating the model's ability to effectively capture the most spatial features, and by comparing NRMSE across different depths and seasons, the model displays strong seasonal adaptability. In conclusion, this research introduces a novel artificial intelligence technique for estimating OST and OSS in the tropical Western Pacific Ocean.

In this paper, a new axial-type magnetic gear with auxiliary flux-enhancing structure (AFS-AMG) is proposed. Compared to conventional AFS-AMG, it has the higher torque density and higher permanent magnet (PM) utilization factor. Firstly, the design rules and operating principles of proposed AFS-AMG are elaborated. Then, the mapping relation between the radial-type magnetic gears (RMGs) and AMGs are elucidated. Compared to its counterpart in RMGs, AFS-AMGs achieve small size. Then, the geometrical parameters of AFS-AMGs are optimized to obtain the better electromagnetic performances, where the torque density per volume and per PM volume is adopted as the evaluation standard. Finally, three different AMG topologies are constructed in finite element analysis (FEA) software for comparison. It is proven that the AFS-AMG has the largest torque density per volume and per PM volume.

This paper aims to build up a preference function to evaluate the public benefits of the type of agricultural farming, biodiversity, water provisions, land use type, ecotourism modes, and a monetary attribute (environmental trust fund and willingness to contribute) associated with an ecosystem service and land use program in a forest park. This study used the choice experiments to build a random utility model, analyze the average preference for the above land use attributes based on the conditional logit and used a latent class model to test the resident’s heterogeneous preferences for land use planning in the forest park. We also estimated the welfare derived from various land use programs. The empirical result had shown that: (1) increasing organic farming area, maintaining the status quo of species biodiversity, increasing the surface water provision, increasing the area of custom flora, increasing the wetland area, and setting up an integrated framework for ecotourism increase the public’s preference for the land use program; (2) we found that farmer and non-farmer haven’t the same land use preferences; (3) the ecotourism development program incorporating biodiversity, organic farming, ethnobotany, and wetland area with integrated ecotourism are more preferred than other land use program scenarios.

Emerald ash borer (EAB), Agrilus planipennis, an invasive phloem-boring beetle, was detected in the Luhansk Region of Ukraine in 2019. In the following years, it expanded to a large part of the Kharkiv region and the parks of Kyiv. Previous research proved that the climate in Luhansk and neighboring regions is favorable for EAB, and the lack of a host plant (Fraxinus sp.) cannot prevent pest expansion in Ukraine. Considering the necessity to detect inhabited trees in time, our current research aimed to identify the most attractive EAB forest subcompartments considering forest site conditions and stand structure. MaxEnt model predicted the potential distribution of EAB with high accuracy (AUC = 0.842). The most significant five variables provided 82.9% to the model, particularly «Age of trees, years», «Area of forest subcompartment, ha», «Mean height of trees, m», «The proportion of Fraxinus excelsior in the stand composition, %», and «Hygrotope index (humidity level), point». A very high probability of EAB expansion in the Luhansk region (&gt;90 %) is predicted at 20 % of the forest area with Fraxinus sp. in the stand composition. The probability of EAB spread above 30% is predicted for 75 % of such area. To improve the forecasting accuracy, it could be necessary to consider the data on road localization along which the pest can spread passively, as well as dominate wind speed.

This study extends the CGAN-based MODIS cloud vertical-profile (64×64-scene, about 70km width×15km height) retrieval technique developed by Leinonen et al. (2019) [1] to construct seamless 3D cloud fields for the MODIS granules [2]. Firstly, the accuracy and spatial continuity of the Leinonen et al. [1] retrievals are statistically evaluated. Then, according to the characteristics of the retrieval error, a spatially overlapping-scene ensemble generation method and a bi-directional Ensemble Binning Probability Fusion (CGAN-BEBPF) technique are developed, which improves the CGAN retrieval accuracy and support to construct seamless 3D clouds. The CGAN-BEBPF technique involves three steps: cloud masking, intensity scaling, and optimal value selection. It ensures adequate coverage of the low reflectivity areas while preserving the high reflectivity cloud cores. The technique is applied to retrieve the 3D cloud fields of Typhoon Chaba and a multi-cell convective system. The cloud structures of the CGAN-BEBPF results are highly consistent with the ground-based radar observations. It can retrieve weak clouds at the top levels of convective storms and hurricanes that were missed by ground-based radars and fill the gaps of the ground-based radar lower-level PPI scan. Overall, CGAN-BEBPF can be automated to retrieve the rich informative 3D structures of typhoons and severe convective systems over the oceans along the MODIS swath, which certainly presents great value for improving maritime and near-shore typhoons and convection prediction and other cloud-sensitive applications.

Recently, the concept of participatory democracy developed in the early 1970s has come back into fashion to revitalize the public involvement in political decision-making processes. Public par-ticipation in forest policy has been fully conceptualized by the scientific community in the late 1990s and early 2000s, but in many contexts the practical application remains unfulfilled. The aim of this study is to identify and analyze the participatory techniques used in literature to increase knowledge and facilitate its transferability into forest policies and strategies. A literature review was carried out to offer an overview of the participatory techniques adopted in the deci-sion-making process. At the end of literature review, 25 participatory techniques were identified based on over 2,000 publications. Afterwards, the participatory techniques were assessed using seven indicators (degree of participation, type and number of participants, time scale, cost, po-tential influence on policy). The results showed that the type of actors involved in the participa-tory technique is a key variable for the complexity and usefulness of the process, while the number of participants influences how information is disseminated. The Principal Component Analysis highlighted that the participatory techniques can be divided in three groups: the first group includes those techniques with a high degree of participation and a contextual high po-tential influence on policies, the second one includes techniques with a costs in terms of re-sources, while the third one consists of those with a large number of participants and reduced time requirements.

Agroforestry practices evolve with the development of basic and advanced facilities, changes in natural and artificial factors of land use change. The study aims to examine the socioeconomic characteristics and compare satisfaction levels across forest products and vegetable farming of the agroforestry community in Khost Province. Data were collected from 662 farmers and was analyzed using univariate Analysis of Variances (ANOVA) and Multivariate Analysis of Variances (MANOVA). The results found that forest and vegetable products, including fruits, berries, herbs, mushrooms, wild animals, oils, wood, honey, okra, eggplant, carrot, cucumber, pine nuts, pepper, and timber has different impact in terms of satisfaction with basic and advanced facilities, knowledge about land use and impacts, natural and artificial factors of land use change, and positive and negative impact of land use change. The limitation of the study included an absence of exogenous factors in the model such as climate change, financial conditions, market fluctuations, regulatory system, an area in which the study is selected, research design, and current condition of endogenous factors. Overall, agroforestry practices can improve the socioeconomic development of agroforestry-dependent communities in Khost Province, Afghanistan. This study provided useful insights for policymakers and development practitioners to promote agroforestry practice adoption and improve the socioeconomic development of agroforestry-dependent communities. Future works could explore the implications of agroforestry practices on the socioeconomic development of other dependent communities in Afghanistan.

Particulate organic carbon (POC) is a pivotal component within the marine carbon cycle, actively involved in diverse biogeochemical processes. This study focuses on Mediterranean as the research region, selecting the most influential factors from 47 potential ones influencing surface POC. Using geographic detector for factor identification, ten primary influencers were identified. Preliminarily optimized random forest (BRF), backpropagation neural network, adaptive boosting, and extreme gradient boosting were utilized to construct POC assessment models. Notably BRF exhibited superior performance in estimating the sea surface POC. Further optimization of RF using the tuneRanger R package resulted in R² of 0.868, mean squared error of 1.119 (mg/m³) ², and mean absolute error of 1.041 (mg/m³). Surface POC concentrations in the Mediterranean for May and June 2017 were estimated. Spatial distribution analysis unveiled higher concentrations in the west, lower in the east, higher in the north, lower in the south, with higher levels near the coast and lower far from the coast. Additionally, the study deliberated on the impact of human activities on surface POC in the Mediterranean. This research contributes a high-precision method for satellite retrieval of surface POC concentrations in the Mediterranean, thereby enriching the understanding of POC dynamics in the area.

The mechanical properties of the materials stored inside agricultural silos influence the loads generated inside them. The different silo calculation methodologies allow predicting these loads under static and dynamic conditions if the mechanical properties of the stored materials are known. It has been known for many years that these properties are highly dependent on the moisture content of the material. However, to date there are not many studies focused on its determination. The goal of this research is the determination of the angle of internal friction, apparent cohesion, dilatancy angle and apparent specific weight of maize subjected to different moisture contents. Direct shear and oedometer assay devices were used for this purpose. In addition, the maize samples used were moistened using a climatic chamber. Moisture contents applied to maize sample ranged from 9.3% to 17.4%. The results obtained for the angle of internal friction and apparent cohesion, as well as those obtained for the apparent specific weight, were similar to those reported in the literature. However, the values obtained for the dilatancy angle of maize as a function of moisture content could not be compared because nothing has been published so far. The values obtained for this parameter overlap with those published for this material under ambient conditions. In addition, no direct relationship between the values obtained for this parameter and the moisture content of the sample could be found. Finally, the apparent specific weight increased with increasing moisture content of the samples, which differed from that published in the literature. The values provided here can be used for the optimization of storage and handling structures for granular agricultural materials using numerical methods.

Floral nectar is a key reward in Leguminosae despite the exceptional diversity of flowers in this family. The paper aims to summarize the available data on structure, ontogeny, regulation, and possible evolution of the leguminous floral nectaries. To date, detailed characterization of ultrastructure and mode of secretion is available only for a few representative of the family whereas the majority remains understudied from this perspective. In most cases, regardless of flower symmetry, nectaries are localized between stamens and a carpel. The nectar is usually exuded from modified stomata although the exact mode of secretion by specialized parenchyma may differ between taxa. The leguminous floral nectaries often have certain features of monosymmetry with preferentially abaxial development. Nectaries were independently lost in several lineages, and equally recurrent is the emergence of substitutive, i.e. evolutionary innovative, nectar-producing structures. Floral nectaries possess a certain degree of evolutionary inertia, i.e. they remain stable even in lineages in which flower morphology underwent significant changes compared with an ancestral plan, such as shifts in merism, symmetry, organ number and alike. Due to their evolutionary stability, floral nectaries are rarely used in taxonomy of Leguminosae.

Grasping the spatial and temporal patterns of forest fires, along with the key factors that drive them and the ability to forecast such events accurately, is essential for the successful management of forests. In China's southern region, forest fires significantly endanger the ecological system, public safety, and economic well-being. Through the application of Geographic Information Systems (GIS) and LightGBM (Light Gradient Boosting Machine) model, this study investigates the determinants of fire incidents and formulates a predictive model for forest fire occurrences, alongside a zoning strategy, within the Central-South area. The results indicate: (i) Spatially, fire points exhibit significant clustering and autocorrelation characteristics; (ii) The Central-South Forest Fire Prediction Model shows exceptional accuracy, reliability, and predictive power, with high performance metrics across training and validation sets, including over 85% accuracy, precision, recall, and F1 scores, along with AUC values above 89%, underscoring its efficacy in forecasting forest fires and distinguishing between fire events; (iii) Throughout the year, forest fire risks in the Central-South region of China vary by region and season, with risk spikes from March to May in Guangdong, Guangxi, Hunan, Hubei, and Hainan. From June to August, localized risks are observed in Heyuan and Huangshi, while from September to November, an increase in risk is noted in Guangdong (Meizhou, Heyuan, Shaoguan), Guangxi (Nanning, Hezhou, Yulin), and Hunan (Binzhou, Yongzhou, Hengyang) due to cooler, drier conditions and leaf litter accumulation. From December to February, the risk continues in specific areas across Guangdong, Guangxi, Hunan, and Hubei.

The Australian tropical montane cloud forest (TMCF) is home to approximately 18 percent of the nation’s total vascular plant species. Over the past century, human activity and industrial development have caused global climate changes, posing a severe and irreversible danger to the entire land-based ecosystem, and WTWHA is no exception. The current average annual temperature of WTWHA in FNQ is 24 °C. However, in the coming years (by 2030), the average annual temperature increase is estimated to be between 0.5 and 1.4 °C compared to the climate observed between 1986 and 2005. Looking further ahead to 2070, the anticipated temperature rise is projected to be between 1.0 and 3.2 °C, with the exact range depending on future emissions. We identified 84 plant species endemic to the WTWHA in FNQ, which are already experiencing climate change threats. Few of these plants are used in herbal medicines. This study comprehensively reviewed metabolomics studies conducted on these 84 plant species until now toward understanding their physiological and metabolomics responses to global climate change. This review also discusses: i) recent developments in plant metabolomics studies that can be applied to study and understand the interactions of wet tropical plants with climatic stress, ii) medicinal plants and isolated phytochemicals with structural diversity, and iii) reported biological activities of crude extracts and isolated compounds.

This paper explores the capability of various machine learning algorithms, including Random Forests and advanced gradient boosting techniques such as XGBoost, LightGBM, and CatBoost, to predict customer churn in the telecommunications sector. For this analysis, a dataset available to the public was employed. The performance of these algorithms was assessed using recognized metrics, including Accuracy, Precision, Recall, F1-score, and the Receiver Operating Characteristic Area Under Curve (ROC AUC). These metrics were evaluated at different phases: subsequent to data preprocessing and feature selection; following the application of SMOTE and ADASYN sampling methods; and after conducting hyperparameter tuning on the data that had been adjusted by SMOTE and ADASYN. The outcomes underscore the notable efficiency of upsampling techniques such as SMOTE and ADASYN in addressing the imbalance inherent in customer churn prediction. Notably, the application of random grid search for hyperparameter optimization did not significantly alter the results, which remained comparatively unchanged. The algorithms' performance post- ADASYN application marginally surpassed that observed after SMOTE application. Remarkably, LightGBM achieved an exceptional F1-score of 89% and an ROC AUC of 95% subsequent to the ADASYN sampling technique. This underlines the effectiveness of advanced boosting algorithms and upsampling methods like SMOTE and ADASYN in navigating the complexities of imbalanced datasets and intricate feature interdependencies.

The attitude dynamics and orbit dynamics of large rigid space structures are coupled with each other under gravity gradient, which may affect the stability of the large rigid space structures. In this paper, the gravity gradient stability of a large rigid space structure is studied under both small and large disturbances. Based on the rigid body dynamics and orbit dynamics, an accurate dynamic model without any linearization of the large rigid space structure is established via the natural coordinate formulation (NCF), which is able to describe the large overall motions of the structures. By using the generalized-α algorithm, the gravity gradient stability of the large rigid space structure is simulated and analyzed via various examples, including the influence of large disturbance angles, the positions at the stabilization and unstabilization regions. Finally, the relationship between spinning stability and gravity gradient stability is also investigated via a large spinning space structure.

The present work investigates primarily the morphology evolution of the body-centered-cubic (BCC)/B2 phases in AlxNiCoFeCr high-entropy alloys (HEAs) with increasing Al content, which has been neglected so far. There exist two types of microscopic morphologies of BCC and B2 phases in this HEA series: one is the weave-like morphology induced by the spinodal decomposition, and the other is the microstructure of a spherical disordered BCC precipitation on the ordered B2 matrix that appears in HEAs with a much higher Al content. The shape of coherent precipitates is found to be closely related to the lattice misfit between BCC and B2 phases, which is sensitive to Al. The mechanical properties, including the compressive yielding strength and microhardness of the AlxNiCoFeCr HEAs, are also discussed in light of the concept of the valence electron concentration (VEC).

Lignin is insoluble in water, limiting its use in the synthesis of adhesives. Therefore, in order to increase the amount of lignin raw materials used in the synthesis of adhesives, a kind of aminated lignin compounds was prepared through lignin amination reaction, and conducting structural analysis in this paper. The particle size of the amino lignin is about 100 nm, with the weight average molecular weight of 57,627 g/mol and a water solubility of 0.45g/100ml. The reaction mechanisms were proposed that the phenolic hydroxyl groups of lignin react with ammonia molecules, and thereby successfully introducing amino groups to generate the aminated lignin compounds. Therefore, this article enriches the scientific theory of lignin reactions and provides reference for the widespread application of lignin raw materials in the field of adhesives.

Knowledge is not merely the characteristic of certain pieces of information being deemed true and justifiable, but rather a process. Within an axiomatic system, the set of information that reaches the status of knowledge forms a universe that provides an interpretation of the reality one aims to describe. Language exchanges information through communication and the process of justification (exchange of information), if it consistently justifies a particular piece of information, it elevates it to knowledge. In this paper, we provide a framework for knowledge within an axiomatic model where we define the fundamental elements of communication and grammar. As a result, the structure dictates that knowledge, to be considered as such, must be investigateable by anyone who utilizes it in its entirety, both in form and content. Ultimately, the development of knowledge processing, referred to as \emph{knowmatics}, represents a clear evolution of the computer science that processes information (subset of knowledge).

In this study we have investigated the effect of the addition of Nb2O5 (up to 5 mol%) on the structure and luminescent properties of ZnO-B2O3 glass doped with 0.5 mol % Eu2O3 by using of infrared (IR), Raman and photoluminescence (PL) spectroscopy. Physical properties as molar volume, oxygen packing density and glass transition temperature were determined using the results of differential thermal analyisis (DTA) and Archimedes principle for density. IR and Raman spectra revealed that niobium ions incorporate into the base zinc borate glass as NbO4 trtraherda and NbO6 octahedra. A strong red emission from the 5D0 level of Eu3+ ions was registered under near UV (392 nm) excitation using the sharp 7F0 - 5L6 transition of Eu3+. The integrated fluorescence intensity ratio R (5D0 → 7F2/5D0 → 7F1) was calculated to estimate the degree of asymmetry around the active ion, suggesting a location of Eu3+ in non-centrosymmetric sites. The higher Еu3+ luminescence emission observed in zinc borate glasses containing 1÷5 mol% Nb2O5 compared to the Nb2O5-free zinc borate glass evidences that Nb2O5 is suitable component for modification of host glass structure and improving the emission intensity.

The atomic structures of Zn and Na borophosphate glasses were studied by X-ray and neutron diffraction. Peaks assigned to the B−O, P−O, and O−O distances confirm that only BO4 units co-exist with the PO4 tetrahedra. The Zn−O and Na−O coordination numbers are found to be a little larger than four. The narrowest peaks of the Zn−O first-neighbor distances exist for the glasses along a line connecting the Zn(PO3)2 and BPO4 compositions (50 mol% P2O5) which is explained by networks of ZnO4, BO4, and PO4 tetrahedra with twofold coordinated oxygens. Calculated amounts of the available oxygen support this interpretation. Broadened peaks occur for glasses with lower P2O5 contents, consistent with the presence of threefold coordinated oxygens. The two distinct P−O peak components of the Zn and Na borophosphate glasses differ in their relative abundances which is interpreted by Na+ cations that coordinate oxygens in some P−O−B bridges, something not seen for the Zn2+ ions.

Lumpy skin disease (LSD), caused by a virus within the Poxviridae family and Capripoxvirus genus, induces nodular skin lesions in cattle, spreading through direct contact and insect vectors, significantly affecting global cattle farming. Despite available vaccines, their effectiveness is limited by poor bioavailability and adverse effects. Our study aimed to identify potential inhibitors targeting LSD-associated DNA polymerase protein, selecting LSDV039 for further investigation through comprehensive analysis and computational methods. Virtual screening revealed rhein and taxifolin as potent binders among 380 phytocompounds, with respective affinities of -8.965 and -7.195 kcal/mol. Canagliflozin and tepotinib exhibited strong affinities (-9.858 and -8.856 kcal/mol) among 718 FDA-approved antiviral drugs. Molecular dynamics simulations of canagliflozin, tepotinib, rhein, and taxifolin highlighted taxifolin's superior stability and binding energy. Rhein displayed compactness in RMSD and RMSF but fluctuations in Rg and SASA, while canagliflozin demonstrated stability compared to tepotinib. The study highlights the promising potential of repurposed drugs and phytocompounds as LSD therapeutics. However, extensive validation through in-vitro, in-vivo, and clinical trials is crucial for their practical application.

The study aims at evaluating the demand of forest bathing in the Northern Italy’s regions underlining the willingness to pay and the potential tourists’ habits and flows on attending alpine contexts. Through the submission of a questionnaire, the sample’s answers have been analyzed employing a stratified sampling methodology considering three different macro areas (Northwest regions, Northeast regions, and Friuli Venezia Giulia region). After analyzing the sample attitudes, the research approached the estimation section by calculating the flow as the number of potential forest bathing hikes per year and the willingness to pay trough the Contingent Valuation Method. The main results indicate that Forest Bathing activity in Northern Italy have a considerable monetary value and it is generally compared with positive feelings, particularly concerning well-being, and fascination factors.

A brief technical and economic insight into producing the water-soluble yellow colorant limocitrol 3-O-6”-[3-hydroxyl-3-methylglutaryl)])-β-D-glucopyranoside from waste lemon peel via simple solid-liquid extraction in aqueous ethanol or via hydrodynamic cavitation of waste lemon peel in water, shows that the biocolorant can be obtained at affordable cost. Coupled to the simplicity and sustainability of the extraction processes suggested, the high chemical and physical stability of this polymethoxylated flavanol and the health benefits of citrus flavonoids, support industrialization of this new bioeconomy production.

High-spin states of 192Tl are populated by the heavy ion fusion-evaporation reaction 181Ta(16O, 5n)192Tl at 97 MeV beam energy. A new level scheme with eight new levels is constructed and the level spins are tentatively assigned. The negative-parity yrast band is extended up to 23^{-}\hbar. Subsequently, the systematics of signature splitting and signature inversion are discussed for the negative-parity yrast band of odd-odd Tl isotopes including 192Tl, 194Tl, 196Tl, and 198Tl. With the increase of neutron number signature inversion is found in 196,198Tl at high-spin state in these four Tl isotopes. The reason may be due to the competition between neutron-proton interaction and Coriolis force.

(1) Background: The proportion of fully mechanized harvesting systems in Austria is constantly increasing especially because of the technological development of the machines, which allows them to drive on increasingly steep terrain. This leads to additional challenges and potential hazards for the operators, which may also cause higher stress levels. The purpose of this study is to develop and debate a new set of methodologies for determining time and space resolved psychophysiology data to analyze stressful and non-stressful work situations for harvester and forwarder operators; (2) Methods: we suggest a study protocol to analyze a) tasks performed by the driver, b) environmental factors, like slope gradient, c) the psychophysiological response of experts during these tasks, and d) evaluate the worker´s subjective stress and fatigue before and after a harvest operation. (3) Results: Within this manuscript we present a study protocol based on quantitative and qualitative methods, like time and space resolved psychophysiology, questionnaires, qualitative interviews, as well as video and sensor-based analysis of environmental and machine data. The first results from real measurements of a forwarder driver are presented; (4) Conclusions: This multimodal research protocol serves to explore the relationship between stress, fatigue, and performed tasks. Through our quantitative and qualitative methodology, researchers can improve the health and safety of forest workers at work, improve their productivity and reduce damage to remaining trees.

Background: Molecular genetic events are among the numerous factors affecting the clinical course of papillary thyroid carcinoma (PTC). Recent studies have demonstrated that aberrant expression of miRNA, as well as different thyroid-related genes, correlate with the aggressive clinical course of PTC and unfavorable treatment outcome, which opens up new avenues for using them in personalization of the treatment strategy for patients with PTC. In the present work, our goal was to assess the applicability of molecular markers in preoperative diagnosis of aggressive variants of papillary thyroid cancer. Methods: The molecular genetic profile (expression levels of 34 different markers and BRAF mutation) was studied for 108 cytology specimens collected by fine-needle aspiration biopsy in patients with PTC having different clinical manifestations. Results: Statistically significant differences with adjustment for multiple comparisons (p &lt; 0.0015) for clinically aggressive variants of PTC were obtained for four markers: miRNA-146b, miRNA-221, FN1, and CDKN2A. Weak statistical correlation (0.0015&lt; р&lt;0.05) was observed for miRNA-31, -375, -551b, -148b, -125b, mtDNA, CITED1, TPO, HMGA2, CLU, NIS, SERPINA1, TFF3, and TMPRSS4. Conclusions: The recurrence risk of papillary thyroid carcinoma can be preoperatively predicted using miRNA-221, the fibronectin and cyclin-dependent kinase inhibitor 2A genes.

REDD+ (Reducing Emissions from Deforestation and Forest Degradation) aims to achieve its purpose by working across multiple sectors and involving multi-level actors in reducing deforestation and forest degradation in tropical countries. By contrast, the European Union (EU) Action Plan on Forest Law Enforcement, Governance and Trade (FLEGT) and its Voluntary Partnership Agreements (VPAs) focus on forestry and functions at bilateral state level. The FLEGT Action Plan specifically aims to tackle illegal logging, legalise timber production and trade improve forest governance in countries exporting tropical timber to the EU. Since illegal logging is just one driver of deforestation and forest degeneration, and legalisation of logging does not necessarily reduce deforestation and forest degradation, the two instruments differ in scale and scope. However, by addressing the causes of deforestation and forest degradation and their underlying governance issues, the EU FLEGT and REDD+ share many functional linkages at higher levels of forest policy and forest governance. The contribution and participation of civil society organisations (CSOs) and other actors is imperative to both processes. Our study is based on a survey of key actors (national and international) in REDD+ and FLEGT VPA processes in the Lao People’s Democratic Republic. Our analysis was guided by the theoretical perspectives of the policy arrangement approach and examination of two specific dimensions of this approach, namely resources and rules of the game. This paper argues that participation of CSOs in both processes is crucial as it facilitates and nurtures the very much needed cooperation between other national and international actors. The paper also argues that participation of CSOs feeds valuable information and knowledge into REDD+ and FLEGT VPA processes, thus contributing to increased legitimacy, justice and transparency.

The silver fir (Abies alba Mill.) is among the most valuable conifers in Europe for ecological and economic reasons. In the course of history, primarily in the 20th century, its share in stands has been declining due to ill-suited management practices, especially clear-cut management, air pollution, and wildlife-induced damage. Based on recent knowledge of fir ecology and population dynamics, small-scale shelterwood and selection management have been introduced in fir stands, which have also stabilized them. Fir is an essential species for maintaining high stability and biodiversity, especially on planosols and in waterlogged habitats. Due to its shade tolerance and environmental flexibility, particularly at higher altitudes, it can coexist very well with many tree species in mixtures, which can increase the productive potential of stands. It can form stands of heterogeneous structure, ranging from single to multi-layer to selection. For its successful natural regeneration, it is essential to reduce cloven-hoofed game and thus prevent bud browsing damage. On the other hand, fir is a species relatively resistant to bark stripping and the spread of secondary rot compared to Norway spruce (Picea abies [L.] Karst.). During global climate change, fir is expected to shift to higher elevations with sufficient precipitation, while in the southern part of its natural range or at lower elevations, outside water-influenced habitats, it is likely to decline. This paper essentially reviews the description and distribution of the species, its ecological requirements, threats and diseases, habitat and stand conditions, and close-to-nature forest management practices with emphasis on ongoing climate change.

As the largest carbon pool on Earth, forest ecosystems are essential to maintaining carbon sink balance. However, accurately estimating the carbon sequestration and carbon storage of forest resources remains an urgent issue to address. Plot investigation, model estimation, and machine learning are examples of current approaches. Nevertheless, because of variables such as regional characteristics and plot size, large-scale and extensive region estimates are comparatively scarce. This study, which focuses on Tianzhu County, aims to comprehensively analyze and estimate the Net Primary Productivity (NPP), carbon storage, and carbon density of the forest ecosystem in this area by integrating data from forest resource inventory and the CASA model. The main conclusions are as follows: (1) The main vegetation types in Tianzhu County include coniferous forests, broad-leaved forests, mixed forests, and shrub forests; (2) Accordin g to the CASA model calculations, the annual cumulative NPP in Tianzhu County in 2020 ranges from a maximum of 249.63 gC/m² to a minimum of 3.40 gC/m², with the forest NPP amounting to 134,674.65 tons of carbon. Based on MODIS observation data, the forest’s NPP is 171,728.32 tons of carbon, with a maximum of 325.36 gC/m² and a minimum of 0.02 gC/m²; (3) At the pixel scale, the carbon storage of forests in Tianzhu County is 361,700 tons. Specifically, 46,500 tons of carbon are stored in coniferous forests, 1,100 tons in broad-leaved forests, 500 tons in mixed forests, and 313,600 tons in shrub forests.

In recent decades, the requirements for implantable medical devices increased, but the risks of implant rejection still exist. These issues are primarily associated with poor osseointegration, leading to biofilm formation on the implant surface. This study focuses on addressing these issues by developing a biomaterial for implant coatings. 45S5 Bioglass has been widely used in tissue engineering due to its ability to form a hydroxyapatite layer, ensuring a strong bond between the hard tissue and the bioglass. In this context, 45S5 bioglasses, modified by the incorporation of different amounts of copper oxide, from 0 to 8 mol%, were synthesized by the melt-quenching technique. The incorporation of Cu ions does not show a significant change in the glass structure. Since the bioglass exhibited the capacity of being polarized, and therefore promoting the osseointegration effectiveness, the electrical properties of the prepared samples were studied using the impedance spectroscopy method, in the frequency range of 102-106 Hz and temperature range of 200-400 K. The effects of CuO on charge transport mobility were investigated. Additionally, the bioactivity of the modified bioglasses was evaluated through immersion tests in simulated body fluid. The results revealed the initiation of a Ca-P-rich layer formation on the surface within 24 h, indicating the potential of the bioglasses to enhance the bone regeneration process.

This letter presents a dual-frequency terahertz amplitude modulator based on a cross-shaped structure and U-shaped metal patches. Its structural unit is a typical metal-substrate structure. The top metal consists of a cross-shaped structure and U-shaped metal patches, and the bottom substrate layer is made of quartz. Amplitude modulation is achieved by adjusting the temperature of the vanadium dioxide (VO2) patches. The modulation depth can be approximately 75%. The mechanism of the resonance frequency is explained by the equivalent circuit model. The proposed structure shows good amplitude modulation capability at different incidence and azimuth angles by changing the location of the VO2 patches. The dual-frequency terahertz amplitude modulator can be used in terahertz communication, imaging, etc.

Purpose of review The forest industry has deployed ICTs to improve productivity of forest supply chains. In this sense, digitalization of data flows significantly impacts wood supply chains, from forest to mills, which must react flexibly to market fluctuations of forest products. The goal of this study was to conduct a literature review on data flow implementations in management systems of wood supply chains and to evaluate their applicability in supply chains to analyze the opportunities for improving them in practice. Recent findings We utilized the ScienceDirect database, Scopus and Web of Science in order to document data flows in systems and actual applications. Due to ongoing outsourcing, the wood procurement chains, and the wood supply chains were identified in the forest industry. Several different technologies can be implemented also in wood supply chains to digitalize the data flow depending on the specific needs of organizations. In this regard, digitalization of Big Data causes significant changes in elements of supply models that should be integrated and standardized in the optimization and simulation systems. Summary A modelling guide is suggested for accurate dynamic solution of problems of forest logistics. Then, the opportunities in digitalization for connecting different data flows, technologies, and stakeholders are discussed thoroughly. We conclude that data-driven dynamic optimization, and locally implemented digitalization contributes to wood supply modeling in the establishment of standards for cloud-based platforms at time-related and sequential measures which will ensure successful forest logistics through the planning and the monitoring of wood supply chains.

To clarify effects of weathered coal humic acid on water-stable aggregates and pore characteristics of reclaimed cambisol, this research analyzed the evolution characteristics of soil aggregates and pores. Effects of different humic acid dosages (0, 1%, 3%, and 5% by weight) and application period (1 year, 2 years, and 3 years) on soil aggregates and organic carbon components in soil water-stable aggregates were investigated. The results showed that water-stable macroaggregates (&gt;0.25 mm) had the highest content in the first year; but in the third year, water-stable microaggregates (0.053–0.25 mm) had the highest content, and silt and clay (&lt;0.053 mm) were at a maximum. In the third year of 5% treatment, mean weight and geometric mean diameters were the largest, soil structure was the most stable, and TOC and water-stable microaggregates (0.053–0.25 mm) in soil had the highest proportions. For 5% treatment, the majority of irregular pores were independent in the first year, and number of pores decreased in the second year, but average pore volume increased, forming robust connected pores. In the third year, the number of elongated and irregular pores increased. In the third year of 5% treatment, most pores were irregular and of size &gt;100 μm, and soil structure was the most stable.

The relationship between the structure characteristics and performances of coal based hydrogenation isomeric base oil (CTL) and metallocene catalyzed coal based polyalphaolefin (mPAO) base oil was clarified here. CTL and mPAO were compared with typical petroleum based and natural gas based commercial API Class III and IV base oils. Pressurized differential scanning calorimetry (PDSC), Rotary Bomb Oxidation Test (RBOT) and four-balls friction tester were used to evaluate the oxidation stability and lubrication performance of base oils under different working conditions. The sensitivity of different base oils to typical antioxidants and extreme pressure antiwear agents was compared. Specially, the composition and structure of CTL base oil are obviously different from GTL and mineral base oil. The coal-based CTL and mPAO base oils exhibit commendable viscosity-temperature properties, characteristics, coupled with low-temperature fluidity, fire safety, and minimal evaporation loss. The lubricating properties, oxidation stability and the sensitivity to extreme pressure antiwear agents of CTL are close to those of similar base oils. But the sensitivity of CTL to typical antioxidants is relatively poor. Besides, compared with commercial PAO base oil, mPAO has lower isomerization degree and fewer isomerization types. The oxidation stability and sensitivity to typical antioxidants of mPAO base oil are comparable with those of commercial PAO base oil, while its lubrication performance and sensitivity to typical extreme pressure antiwear agents are significantly better than those of commercial PAO base oil.

Good governance in natural resource management (NRM) is one of the most challenging issues in developing countries that often inappropriately embedded in national policies and political agendas. It is, in fact, even more important for countries like Bangladesh with exceptionally high pressure and dependence on its natural resources for sustaining rural livelihoods. Globally, nowadays, good governance is considered as one of the key factor for achieving the goal of sustainable development and biodiversity conservation. Bangladesh, of late has responded to that global zeal by involving local communities in the management of country’s declining forest and other natural resources. The colonial legacy of the forestry sector of Bangladesh was planned and, managed as interim projects through donors’ prescriptions. Thus, institutions, management processes and conservation outcomes were problematic. The conventional approach adopted by colonial and post-colonial regimes for forest management also proved to be inefficient due to its top-down management system. The absolute dependency on donor support, and their prescription sometimes worsened the situation both ecologically and socially. Global, regional and local trends supported the need for a different dimension in the governance paradigms. The introduction of a pluralistic approach, known as co-management in protected areas (PAs) is an example of an attempt whereby shared governance mechanism are implemented to attain the desired goals of conservation that will also address the livelihoods and aspirations of communities living in and around PAs of the country. However, in designing future forest and PA regimes the concern of the external aid support and attached conditions remain a reality that needs to be addressed. Adequate attention should be given to our vanishing biodiversity, culture and community livelihoods through devising an appropriate governance mechanism recognizing and supporting local rights, access and participation in the environmental management. It is now time to mainstream the adhoc nature of governance according to our national conservation strategy and policy frameworks in order to achieve the goals and objectives of the Bangladesh NRM sector addressing the human and community right of people in the specific context of forest protected areas management.