A nonlinear MEMS multimass sensor is investigated. The MEMS design consists of an array of nonlinear microcantilevers clamped to a shuttle mass which, in turn, is attached to a linear spring and a dashpot. The microcantilevers are made of a polymeric hosting matrix reinforced by aligned carbon nanotubes (CNT) with different CNT volume fractions in each cantilever so as to suitably tune the frequency bandwidth of the device. The advantages of a single input-single output (SISO) system are here exploited for the design, actuation and detection principles as in previous literature.

Atta capiguara is a grass-cutting ant species frequently found in Cerrado biome. However, little is known about the giant nest architecture of this ant. In this study, we investigated the architecture of three A. capiguara nests from the fragment of cerrado in Botucatu, São Paulo, Brazil. Casts were made of the nests by filling them with cement to permit better visualization of internal structures such as chambers and tunnels. After excavation, the depth and dimensions (length, width, and height) of the chambers were measured. The results showed the typical shape of Atta capiguara nests consisting of mounds of loose soil with unique features resembling a conic section. The fungus chambers were found outside the apparent main part of the nest and were spaced apart and distributed laterally at ground level. The waste chambers were located beneath the largest mound of loose soil. Both the fungus and waste chambers exhibited a sectoral distribution. Our study contributes to a better understanding of the so far unknown nest architecture of the grass-cutting ant A. capiguara.

The present paper offers a reading of three selected novels by two Anglophone Arab writers Diana Abujaber and Fadia Faqir. Our reading is fundamentally based on a philosophical post-humanist perception of other ethnic minorities as being inferior and un-human. In interpreting the three novels, Arabian Jazz (2003), My Name is Salma (2007) and Willow Trees Don’t Weep (2014), a main concern is to bring to light how Arabs –and Muslims –have been zombified and de-humanized in Western mainstream media and culture based on a biased stigmatization and stereotyping of a large heterogeneous ethnic group wherein religions, traditions, languages and cultures are diverse. Also, a pivotal preoccupation is going to be the exiling journey of the protagonists from their homelands to Western countries, and how these journeys contribute to the post-humanization of the self, the identity and the culture of Arab displaced immigrants.

Turbo-roundabouts are one of the most frequently recommended road junction design options when it comes to increasing traffic capacity and traffic safety. This is in particular true of suburban areas, with dominant traffic flow on the main road and moderate traffic flow on the side road. Other intersections handling local traffic and considerably constricting the availability of space are usually located in the vicinity of such intersections. Another factor contributing to less availability of land for construction in these locations is the presence of surrounding residential housing. Then choosing the suitable turbo-roundabout type becomes the main issue. The article presents a case study for the selection of a type of turbo roundabout under the conditions of considerably constricted land availability, based on analyses of provision of swepth path for the chosen design vehicles. The article considers the typical Egg type turbo roundabouts, "flattened" turbo roundabouts and ellipse based roundabouts, with unconventional geometries of the truck apron and central island. For each of the analysed roundabout types setting out methods were described in detail, which enable designers to quickly select a type of roundabout suitable for specific constrained site conditions.

Steel fibers (SF) and polyolefin (PF) are widely used for shotcrete, especially in tunnelling. Both SF and PF and have shown to meet the standards in order to reduce or substitute the conventional steel mesh as reinforcement of concrete showing mechanical and productive advantages. This study sought the analysis and assessment of the mechanical properties of fiber reinforced shotcrete, comparing in-situ with laboratory results. This was performed with low and high fiber dosages of SF and PF as well as a combination of them (hybrid mixtures). A total of seven mixtures, two of steel, two of polyolefins, two hybrids and a control mixture were manufactured at laboratory and in situ. By performing tests according to EN 14651 and slabs according to EN 14488-5, it was possible to characterize the residual flexural strengths (fRj), and energy absorption capacity (E25mm) in slabs. In addition, a fracture surface analysis was performed, and the orientation factor was obtained. This allowed the authors to quantify the loss of residual strength on site and correlate it with the fiber content and positioning. Moreover, some relationships between beam and slab tests were found, allowing to correlate the most relevant type of tests in the field of fiber reinforced concrete.

A portable laser photoacoustic sensor based on a Field-Programmable Gate Array (FPGA) is reported for methane detection. A tunable DFB diode laser in the 1654 nm wavelength range is used as an excitation source. The photoacoustic signal processing was implemented by a FPGA device. A small resonant photoacoustic cell is designed. The minimum detection limit (1σ) of 10 ppm for methane (CH₄) is demonstrated.

When ground-penetrating radar is used to detect targets within concrete, the location of the targets, the identification of different shapes, properties and less obvious echoes all greatly increase the interpretation time of the staff and can easily cause misjudgment of the echo images. In this paper, the ground-penetrating radar echo images (B-scan) after processing are mean filtered to eliminate the direct waves that interfere greatly with the echoes. The RFB-s structure is added to the YOLOv3-SPP network structure, while the Anchor value is optimized and the EIOU loss function is introduced. For four types of data with different shapes and properties at random target locations, three models, YOLOv3, YOLOv3-SPP and the improved YOLOv3-SPP, are used for classification and identification, and the proposed algorithm models are comprehensively evaluated using model evaluation metrics. The experimental results show that the algorithm models proposed in this paper have good recognition effect in ground-penetrating radar echo image target detection.

Arbuscular mycorrhizal fungi (AMF) and rhizobium play a significant role in plant symbiosis. However, their influence on the soil microbiome associated with plant growth and soil health is not well defined in the Northern Great Plains. This study investigated the effect of microbial inoculants as seed treatment on plant yield, nutrient uptake, potential microbial functions, and rhizosphere soil microbial communities using high-throughput sequencing of 16S and ITS rRNA genes. The experiment was conducted under two contrasting dryland conditions with four treatments: control, single inoculation with AMF or Rhizobium, and dual inoculations of AMF and Rhizobium (AMF+Rhizobium). Our findings revealed that microbial inoculation efficacy was site-specific. In a non-P nutrient limiting condition, AMF+Rhizobium exhibited a synergistic effect on grain yield in Sidney, Montana (MT), dryland field site (DFS) 2. While AMF conferred plant resilience but marginal yield in low soil organic matter and acidic soil conditions in Froid, MT (DFS 1). Noteworthy, variation in microbial community structure and composition indicates site-specific response to AMF and AMF+Rhizobium microbial inoculants. Overall, site-specific factors had a greater influence on plant nutrient uptake, microbial community dynamics and functional potential. It underscores the need for tailored management strategies that consider site-specific characteristics to optimize benefits from microbial inoculation.

Identifying ambient noise-based (ANb) signatures of streams can help in the estimation of their erosive potential (EP) that promotes reverie landslides and soil losses in the fluvial valleys. This is particularly imperative on flooding or rainy days, leading to stronger erosion-prone conditions (colluvium and boulders) of the valley beds inferred from georadar attribute analysis. Developing such research direction can benefit the local communities, as is the case with the Cerrado region of Brazil, where these phenomena have high destructive potential with social, economic, and climatic implications. For the present study, a seasonal stream in the Federal District of Brazil was investigated by ANb monitoring supported by Ground Penetration Radar (GPR) for site characterization. The ANb monitoring was conducted (at a safe distance) with a seismometer over several durations of dry and rainy conditions. The power spectral density (PSDs) was computed as a function of several variables, including weather conditions (rainfall, wind speed, and pressure), time-frequency spectrograms, and ambient noise displacement root mean square (RMS). This analysis also considered the single station horizontal-to-vertical spectral ratio (HVSR), where rain, wind, pressure, river flow and anthropogenic signatures were evident (at selective frequency ranges). Multi-peaks that emerged on the HVSR curve were further analyzed to identify amplitude and frequency changes, and the three peaks shift on average to a lower position during the rainy period. The GPR amplitude and waveform variation features were attributed to the stratigraphy (i.e., the boundary between valid and invalid regions and coherence value) of the floodplain and regions susceptible to erosion (erosion-prone lithological spots). This approach provides the basis for non-destructive monitoring tools enabling the detection of 'seismic signatures' and weak spots of the fluvial channels for improving environmental management.

A new Pd(II) complex of the previously reported ligand N,N′-bis[(2,2′-dihydroxybiphen-3-yl)methyl]-N,N′-dimethylethylenediamine (L) was obtained from a DMF/H2O mixture. It differs from a Pd(II) complex of L previously obtained by sole DMF. The roles in the solid state assembly of solvent molecules and molecular conformation (driven by specific transition metal ions) were studied by comparing six complexes of L containing different metal centers (Ni(II), Cd(II), Cu(II), Pd(II)). Hirshfeld surface analysis, 2D fingerprint plots and energy frameworks calculations were used to investigate the intermolecular interactions within the crystal packing of the six complexes. As suggested by interaction energies, Pd(II) and Ni(II) complexes arrange to form ribbons, while Cd(II) and Cu(II) complexes form 3D networks. Interactions between complexes and solvent molecules in the previous Pd(II) complex are replaced by complex-complex interactions in the new Pd(II) complex, while BuOH and MeOH are interchangeable in the interactions within the crystal packing of the two Ni(II) complexes. Finally, solvent molecules are not involved in the crystal packing of the Cu(II) complex. The present study suggested that the solid state assembly of these systems is mainly driven by the molecular conformation, that depends in turn by the metal ion involved, while the solvent only plays a minor role.

COX II containing a dual core CuA active site is one of the three core subunits of mitochondrial Cco, which plays a significant role in the physiological process. In this report, the full-length cDNA of COXⅡ gene was cloned from Sitophilus zeamais, which had an ORF of 684 bp encoding 227 amino acids residues. The predicted COXⅡ protein had a molecular mass of 26.2 kDa with pI value of 6.37, and multiple sequence alignment and phylogenetic analysis indicated that Sitophilus zeamais COXⅡ had high sequence identity 78.51% with the COXⅡ of other insect species, especially similarity to sitophilus oryzae. This gene was subcloned into the prokaryotic expression vector pET-32a, and induced by IPTG in E.coli Transetta (DE3) expression system. Finally the COXⅡ with 6-His tag was purified using affinity chromatography with Ni²⁺-NTA agarose. WB showed the recombinant COXⅡ was about 44 kD, and the concentration of fusion protein was 50μg/mL. UV-spectrophotometer and infrared spectrometer analysis showed that recombinant COXⅡ could catalyze the oxidation of substrate Cytc, and influenced by AITC. It was found that AITC could form a hydrophobic region with COXⅡ protein via molecular docking, besides, a sulfur atom of AITC structure could form a length of 2.9 Å hydrogen bond with Leu-31. These results will provide valuable information for elucidating the role of COXⅡ in Sitophilus zeamais responses to AITC, meanwhile, it will helpful to carry out a point mutation in AITC binding sites for the future research.

MicroRNAs (miRNA) exert regulatory actions via base-pairing with their binding sites on target mRNAs. Cooperative-binding, i.e., synergism, among binding sites on a mRNA is biochemically well-characterized. We studied whether this synergism is reflected in global relationship between miRNA-mediated regulatory activity and miRNA-binding-site count on the target mRNAs, i.e., leading to a non-linear relationship between the two. Recently, using our own and public datasets, we have enquired into miRNA regulatory actions: first, we analyzed the power-law distribution pattern of miRNA binding sites; second, strikingly, mRNAs for core miRNA regulatory apparatus proteins have extra-ordinarily high binding site counts, forming self-feedback-control loops; third, we revealed that tumor suppressor mRNAs generally have more sites than oncogene mRNAs; and fourth, we characterized enrichment of miRNA target mRNAs in translationally less-active polysomes relative to more-active polysomes. In these four studies, obvious correlation was observed qualitatively between the extent to which a mRNA is miRNA-regulated and its binding sites count. This paper summarizes the used datasets. We also re-analyzed the correlation by comparative linear and non-linear regression analyses. The results support a non-linear, instead of linear, relationship between the two parameters, conceivably a transcriptome-level reflection of cooperative-binding/synergism among miRNA binding sites on a target mRNA.

Reasonable allocation of production plans and saving the overall electricity cost are crucial for large manufacturing conglomerates, which is an effective way for conglomerates to realize open-source and cost-saving. This paper develops an optimization model of off-site industrial production scheduling for enterprises in response to the problems of high electricity costs due to the irrational allocation of production schedules on the demand side of China's electric power and the difficulty of promoting industrial and commercial distributed photovoltaic (PV) projects in China. The model makes full use of the conditions of different PV resources and different electricity prices in different places to optimize the scheduling of industrial production in different places. The model is embedded with two sub-models of the electricity price prediction model and distributed photovoltaic kWh cost model to complete the model parameters, in which the electricity price prediction model utilizes the LSTM neural network. The integrated model is then solved by the particle swarm algorithm. To verify the effectiveness of the model in solving the problem of off-site production scheduling on the demand side of electricity, the research team researched two off-site pharmaceutical factories belonging to the same large pharmaceutical company. Finally, the research data were substituted into the model for solving, and it was concluded that the optimization model could significantly reduce the cost of electricity consumption of the enterprise by about 7.9 %.

Thromboembolic conditions, such as stroke and myocardial infarction [MI], are the primary causes of mortality globally. High efficiency was demonstrated by fibrinolytic enzymes isolated from microbial sources in dissolving various blood clots. The study aimed to investigate and produce bacterial fibrinolytic enzymes from various Egyptian soil conditions using recombinant DNA technology. Fifty soil samples were examined to determine the production of fibrinolytic enzymes. The plasmin plate technique assessed the thrombolytic activities of the strong fibrinolytic enzyme-producing bacterial isolates. In addition to determining the molecular mass using a mass spectrometer and the western blot method, the activity and thermostability of the enzymes were characterized. An affinity chromatography approach was used to purify the fibrinolytic enzymes. However, bacterial recombinant DNA technology produced the pure bacterial fibrinolytic enzyme. Several dosage formulations for the formulation of fibrinolytic enzymes were tested. By using affinity chromatography and the SDS-PAGE test, the isolated bacterial fibrinolytic enzyme in this investigation was almost 83% pure. Bacillus cereus ATCC 4342 was identified as the predominant bacterial isolate secreting fibrinolytic enzymes. It was discovered that the fibrinolytic enzyme activity of fifty soil samples ranged from 0.167 U/ml to 1.853 U/ml. The extracellular enzyme extracted from Bacillus cereus culture supernatant demonstrated a relatively stable fibrinolytic activity over 18 hours at a pH range of 7.4–10, as well as stability with maximum productivity at 43℃ for over 60 minutes. In this investigation, the enzyme was referred to as Fibrin-proteinase[ FP]. The fibrin clots were directly thrombolyzed by the FP. The calculated values for the specific activity and molecular mass of the FP were approximately 40.71 units/mg of protein and approximately 30 KDa, respectively. It was observed that the presence of Fe+3 marginally boosted protease activity, but the presence of EDTA decreased it. On the other hand, adding monovalent cations like K+1 and Na+1 significantly increased the fibrinolytic activity of FP. The enzyme exhibited activity throughout the temperature range of 20 to 65℃, peaking at 55℃. The ideal range for the generation of protease was 35–43℃ and 8.0–10. The thermostable fibrinolytic enzyme FP, which was isolated from Bacillus cereus ATCC 4342 in various soil environments in Egypt during the current study, was a promising fibrinolytic enzyme because it demonstrated a more extensive and effective fibrinolytic activity and fewer side effects than the fibrinolytic enzymes that are currently available worldwide. It is advised that further research be done on optimizing the right formulation of bacterial fibrinolytic enzymes in the future to help dissolve different types of blood clots and, as a result, lower the high death rate that exists worldwide.

The morphological aspects of urban growth on wetlands in Africa are under-researched. Using the Densu Delta Ramsar site in Accra, Ghana, as a case study, this paper analyses the morphological patterns and drivers of urban growth and its impact on wetlands. Data were obtained through remote-sensing, ground truthing and limited key informant interviews. The analysis combined land use/land cover, building coverage and multiple regression techniques, with the aid of GIS and STATA software. The findings reveal that urban growth at the Ramsar site follows discernible spatial patterns consistent with the spreading pancake, village magnet and ribbon development models. However, the primary force behind these patterns is growing demand for land to meet housing needs, aided by the failure of state institutions to perform their land use control and wetland protection functions. To achieve sustainable urban development, there is an urgent need to ensure effective wetland management by enforcing existing land use, development control and wetland protection measures. This calls for the strengthening, resourcing and closer collaboration between the various state agencies responsible for urban planning and wetland management. There is also the need to engage and sensitise political leaders to increase their commitment to implementing wetland protection and pro-environmental policies.

The Giant Babax, an endemic bird in China and a nationally protected wildlife species of Class Ⅱ, is primarily distributed in southern and southeastern Tibet. To investigate the factors influencing nesting site selection, this study conducted research on nest characteristics and nesting site preferences at four sample sites around Lhasa from March to October 2023y, using systematic search methods, tracking methods, and sampling methods. The research findings are as follows: (1) The average nest depth was (7.70±1.47)cm, nest height was (19.58±2.97)cm, inner diameter was (10.64±1.73)cm, outer diameter was (24.65±4.8)cm, average weight was (162.3±13.5)g, and average nest spacing within the plot was 396.93m. (2) The nests of Giant Babax were predominantly found on vegetation such as Salix longistamina (38%), Hippophae gyantsensis (20%), Rosa sericea Lindl. (14%), and Populus szechuanica Schneid(11%). They showed a preference for artificial secondary forests as nesting sites. (3) Giant Babax exhibited a preference for habitats with robust trees that had high canopies while being distant from houses and roads, but close to water sources; moreover, the canopy of the nesting tree played a crucial role in their choice of nesting sites. (4) The reproductive success rate reached 76%, with key factors affecting it being the canopy coverage of the nesting tree and the number of helpers. These research results provide fundamental data support for population conservation efforts and ecological resource management strategies concerning the Giant Babax.

In the quest for more sustainable urban landscape development, the concept of ‘green infrastructure’ (GI) has become central in policy documents and as a multifunctional general planning tool. GI is not however a simple and unambiguous solution. While there in policy documents are claims for more and connected GI, actual urban development takes another direction. The densifying imperative is hard to combine with an increased and more connected GI. This paper argues for a critical and diversified approach to the concept of GI, to facilitate its implementation in urban planning and management. While GI most often is seen as a common asset and a public good, the actual land use negotiations and management responsibilities cannot be limited to a public service discourse, but should address more clearly a variety of actors. Linguistic as well as spatial definitions of the two relevant dichotomies of ‘green-grey’ and ‘public-private’ are crucial in GI location, design, construction and management, it is argued. Overarching representations of GI will be needed, but also – and linked to it – a spatial storm water plan and an overall plan for public space. The development over time will need an intersectorial implementation and management program. Thus some of the GI intentions may be implemented in planning processes, some through reorganisation and redesign of public space, and some by agreements with landowners.

Background: Schistosome egg deposition in pregnant women may affect the placenta of infected mothers and cause Placental Schistosomiasis (PS). Histopathological examination of placental tissue is an inadequate detection method due to low sensitivity. So far, there has not been any sys-tematic review on PS. Methods: We conducted a systematic literature search on PubMed and in-cluded relevant secondary literature found in the citations of the primarily included publications. Results: We found a total of 8 publications describing PS with a total of 92 cases, describing egg deposition of dead and/or viable eggs and worms of S. haematobium and S. mansoni in placental tissue. One cross-sectional study investigating the prevalence of PS and its association to adverse birth outcomes, found 22% of placentas to be infested using a maceration technique but only < 1% using histologic examination. Additionally, no direct link to deleterious pregnancy outcomes could be shown. Conclusions: PS is a highly unattended and underdiagnosed condition in en-demic populations, due to a lack of awareness as well as low sensitivity of histopathological examinations. However, PS may play an important role in mediating or reinforcing adverse birth outcomes (ABO) such as fetal growth restriction (FGR) in maternal schistosomiasis, possibly by placental inflammation.

In this research the efficiency of degradation of different organic contaminant classes, including pesticides (tembotrione, clomazone), pharmaceuticals (ciprofloxacin, 17α-ethinyl estradiol) and mycotoxins (zearalenone, deoxynivalenol, fumonisin B1), by subcritical water treatment, was studied in model systems. All experiments were conducted in a house-made batch type pilot reactor. The research was focused on the optimization of the treatment parameters by using moderate treatment conditions. Optimization of the remediation processes of water contaminated with 17α-ethinyl estradiol, tembotrione, clomazone, ciprofloxacin, was conducted by testing different homogeneous and heterogeneous catalysts, as well as different gas atmospheres (nitrogen and carbon-dioxide) for pressurization of the process system. Mycotoxins in water were degraded without catalysts and all experiments were conducted in nitrogen atmosphere. Optimization was conducted by defining the optimal combination of the treatment temperature and time, oriented towards energy saving and minimization of the technical requirements. The degradation efficiency in all tested samples was determined by HPLC analysis.

Flooding, exacerbated by climate change, poses a significant threat to certain areas, increasing in frequency and severity. In response, the construction of supplementary dams has emerged as a reliable solution for flood management. This study employs a Remote Sensing (RS) approach integrated with GIS to assess the feasibility of constructing a supplementary dam near Linville, Brisbane, Australia, with the aim of mit-igating floods and preventing overtopping failure at the Wivenhoe Dam. Using QGIS software and a 25-meter resolution DEM from the Queensland Spatial Catalogue ‘QSpatial’ website, four potential dam sites were analysed, considering cross-sections, watershed characteristics, and water volume calculations. Systematic selection criteria were applied to identify the most optimal option based on dam wall di-mensions, volume-to-area, and volume-to-cost ratios. The selected option was further assessed against predefined criteria, yielding one optimal choice. The study provides insights into the feasibility and ef-fectiveness of supplementary dam construction for flood mitigation in the region, with recommendations for future research and implementation.

Studies have demonstrated the critical role that safety plays in preserving favourable working conditions in the construction industry, which is necessary to accomplish goals. The aim of this research was to inform stakeholders in the construction industry in developing nations about the value of safety and possible strategies for influencing their opinions regarding safety protocols. The importance of safety to the construction sector, which is crucial to the advancement of the country, has also been emphasized. However, due to a lack of adequate safety understanding among stakeholders in the construction sector, the construction industry is characterized by a great deal of instability and hazard. To determine what factors, affect productive working conditions in the construction production, this study examined safety. A conceptual framework for safe working conditions in the construction sector was developed by considering several aspects, including the person dimension, environment factor, safety behaviour, organization features, technology, and incentives. It is now imperative to bring in these dimensions to improve the safe working conditions in the construction industry, particularly in the developing countries. By putting these safety factors into practice, the construction industry can reduce safety risks, lower the number of accidents and fatalities, cut expenses related to subpar safety performance, safeguard the reputation of construction companies, boost employee morale and satisfaction with their work, enhanced employee retention, reduced absenteeism, and enhanced sustainability goals. Additionally, the proposed conceptual framework is assured to be new and to be widely accepted in the developing nations. Based on this assumption the conceptual framework is designed.

Green synthesis of silver nanoparticles (AgNPs) using raw Whey has never been reported. Silver nanoparticle formation involves a reduction reaction of silver salt solution with Whey extract. Extract and metal salt concentrations, and temperature can control this reaction. In this work, incubation period, extract, AgNO3, and NaOH concentrations were used as the independent factors using central composite design under response surface methodology. The aim was to elucidate the influence these factors have on the measured UV-Vis absorption spectra fitted with a Voigt function, and to optimize the conditions for nanoparticle formation. The fitting parameters, peak wavelength (λ0), peak area (A), and Full Width at Half Maximum (FWHM), were the responses. Silver nanoparticle formation was only possible in an alkaline environment (pH 10). The peak wavelength and the FWHM are influenced mainly by extract and AgNO3 concentrations. In contrast, the peak area is influenced by a total of 33.54 % from the interaction terms of AgNO3 and extract concentrations with NaOH. Metallic AgNPs were formed for the following parameter ranges: a) Whey (0.4 – 1.6 % v/v), b) AgNO3 (0.15 – 0.6 mM), c) NaOH (10 – 50 mM), and d) Time (20 – 60 min). Silver oxide nanoparticles were also observed.

Background: Bacteria can survive antibiotic exposure by mechanisms like tolerance without a shift in antimicrobial susceptibility. In this study, we investigated the presence of tolerance to three antimicrobials, ceftriaxone (CRO), azithromycin (AZM), and ciprofloxacin (CIP), in clinical isolates and WHO reference panel of N. gonorrhoeae and explored the prevalence between urogenital and anorectal infection sites. Methods: We examined 66 N. gonorrhoeae clinical isolates, evenly divided between anorectal and urogenital infection sites, using a modified tolerance disk (TD test) for three antibiotics. The isolates underwent a three-step incubation process wherein the isolates were exposed to an antibiotic disc for 20 hours of incubation (Step I), followed by the replacement of the antibiotic disc with a nutrient disc for overnight incubation (Step II) and additional overnight incubation with extra nutrients (Step III). Results: Four isolates were lost due to contamination. Of 62 clinical isolates, 7 exhibited tolerance to AZM, with 6 from anorectal and 1 from urogenital sites (p = 0.0496). Tolerance to CRO was observed in 11 isolates, which was significantly associated with the infection site, with 9 from the anorectum, and 2 from the urogenital site being tolerant (p = 0.02). Tolerance to CIP was found in 11 isolates, but was not significantly associated with the infection site. Tolerance was also detected in 8 (K, M, N, O, P, U, V, W) out of the 14 WHO (World Health Organization) reference strains, with varying patterns of tolerance to CRO (n=8), CIP (n=2) and AZM (n=1). Conclusion: This study identified CRO, AZM, and CIP tolerance in clinical Neisseria gonorrhoeae isolates. Significant variations in tolerance proportions between anorectal and urogenital infection sites, particularly for CRO, were observed. Additionally, tolerance was detected in WHO reference strains.

This study, conducted with meticulous attention to detail, comprehensively examines the state of plants and their adaptation to Kazakhstan's extra-arid climatic zone of the Mangistau. It uses the collections of woody plants from the Mangyshlak Experimental Botanical Garden in Aktau as a case study and extrapolates the results to the entire region. The study area is arid and unsuitable for many plants, so examining physiological adaptation mechanisms and strategies for preserving plants in unfavourable conditions is crucial. The study employed a range of methods, including the measurement of the intensity of transpiration, leaf hydration, and the content of chlorophyll A, B, and carotenoids. These methods were chosen for their proven effectiveness in similar studies and their ability to provide accurate and reliable data. The samples were also assessed using a point system for resistance to drought, phytophagy, gas tolerance, salt tolerance, winter hardiness, and soil fertility. The results obtained and entered into the IEBG platform “DinTseR” to assess the value of the introduction using a diagnostic scale revealed a high variability (up to 51.7-52.2%) of physiological indicators of growth and development. The highest values of transpiration intensity were observed in deciduous trees and shrubs, rose varieties (205-243 mg/g fresh leaf mass per hour), leaf water content - in climbing plants (68.9%), chlorophyll A and B content - in deciduous plants, and plants - old trees, fruit trees and varietal roses (3.46-3.93 and 1.34-1.84%). Their concentration in coniferous species is almost two times lower (0.63%). A correlation was also made between various significant factors. Twenty regression equations and forecasts have been identified that can be used to diagnose and assess resistance, thereby reducing the cost of determining the introduction value in the conditions of Mangistau. These findings are essential in understanding and preserving the unique flora of the Mangistau region.

The aim of this paper is to apply all the existing pyranometric method, to estimate the sunshine duration from the global solar irradiation, in order to find in their original form the most suitable method for a tropical site. Then, in a second step, one of these methods will be optimized to well fit tropical sites. Five methods in the literature (Step Algorithm, Carpentras Algorithm, Slob &amp; Monna Algorithm, Slob &amp; Monna 2 Algorithm, and Linear Algorithm) were applied with eleven years of global and diffuse solar radiation data. As a result, in their original form, the Step Algorithm is on the first rank. But in the second step, after improving its main coefficients, the Carpentras Algorithm was found to be the best algorithm for tropical site in the southern hemisphere.

In the process of oil and gas development and production, when the flow rate in the wellbore is large, the materials underground will be eroded, causing the operation to be unable to proceed smoothly and reducing the efficiency of oil and gas production. Therefore, optimizing the anti-erosion coating under high-speed flow conditions in wellbore is a very interesting thing. It can greatly improve operational efficiency. In this paper, laser cladding was used to prepare the new coating used in the PDC drill bit. Then, the effects of tungsten carbide and multi-layer graphene on the microstructure and properties of the tungsten carbide coating were studied. The research results indicate that, for new coatings, 60% tungsten carbide and 0.3% graphene are the optimal ratios. After adding WC, the hardness has significantly improved. However, when the WC content further increases more than 30%, the increase in hardness is relatively small. In addition, when the content of graphene is more than 0.3%, the branched structure became thicker, and not only the segregation of Cr, Si and W became very obvious again, but also the segregation of Fe occurred at the Ni enrichment site. The research results contribute to improving oil and gas production and operational efficiency under high-speed fluid flow conditions in the wellbore.

To facilitate the computation of the uniaxial compressive strength value of the cemented paste backfill under the condition of high sand-cement ratio, and to analyze the size effect of the cemented paste backfill with high sand-cement ratio under varied aspect ratios, the cemented paste backfill specimens with sand-cement ratios of 8:1-24:1 and aspect ratios of 0.5, 1, and 2 were prepared. Through response surface experiments and finite element analysis, the influence of three aspect ratios on the cemented paste backfill strength was explored, and the failure characteristics and size effect mechanisms of cemented paste backfill with various aspect ratios were analyzed. The model of strength conversion between cemented paste backfill with different aspect ratios was established. The results show that the compressive strength of the cemented paste backfill decreases with the increase of the aspect ratio under the same mass concentration and sand-cement ratio. When the aspect ratio is 0.5 and 1, the splitting failure is the main factor; when the aspect ratio is 2, the shearing failure is the main factor. The three-dimensional stress caused by the end effect of the cemented paste backfill is the main reason for the high strength when the aspect ratio is 0.5. Due to the one-dimensional stress zone generated in the middle of the cemented paste backfill with an aspect ratio of 2 in the laboratory, its strength value is closer to the actual uniaxial compressive strength value of the cemented paste backfill. The strength values of the cemented paste backfill with aspect ratios of 0.5 and 1 were higher than the actual uniaxial compressive strength values in the laboratory. The rationality of the theoretical analysis was verified by the ABAQUS analysis results. According to the experimental results, a strength conversion model between different aspect ratios is established, which can provide a reference for the design of the uniaxial compressive strength of the cemented paste backfill.

The olive tree (Olea europaea L.) is an evergreen tree that occupies 19% of the woody crop area and is cultivated in 67 countries on five continents. The largest olive production is concentrated in the Mediterranean basin, where the olive tree has had an enormous economic, cultural and environmental impact since the 7th century BC. In the Mediterranean region, salinity stands out as one of the main abiotic stress factors significantly affecting agricultural production. Moreover, climate change is expected to lead to increased salinisation in this region, threatening olive productivity. Salt stress causes combined damage by osmotic stress and ionic toxicity, restricting olive growth and interfering with multiple metabolic processes. A large variability in salinity tolerance among olive cultivars has been described. This paper aims to synthesize information from the published literature on olive adaptations to salt stress and its importance in salinity tolerance. The morphological, physiological, biochemical, and molecular mechanisms of olive tolerance to salt stress are reviewed.

Based on the theory that certain geological fault zones surpass the influence of other abiotic and biotic site factors for mound-building red wood ants (Formica rufa group), an area northwest of Tuttlingen with extremely high ant density was systematically surveyed, taking into account official geological maps. Indicators of active fault zones were recorded. These were additionally examined in a model area using a high-resolution digital terrain model (DTM 1-meter). The study area is located in the Swabian Jura at the western edge of the Albstadt shear zone, where recent seismic activity is documented by frequent earthquakes. The earthquakes are considered to be the cause of gas permeability in the strike-slip faults, around which the clustered nesting sites were mapped. More than 2900 nests of the Formica rufa group were mapped and their site conditions analysed in different geomorphological positions. In addition to recording forestry site conditions, a geological classification was carried out, as well as an analysis of soil gases/mofettes in areas with the highest nest densities. The correlation between forestry data and nest sites did not reveal a consistent pattern. In contrast, the relationships with gas-permeable strike-slip faults, though predominantly covered with Quaternary sediments, could be identified through CO₂- and CH₄-rich gas emissions, mofettes, and doline features. The interpretations were complicated due to different mapping ages and signatures of the geological maps. Fortunately, this issue could be analysed and evaluated in a sub-area with mappings from 1936/71 and 1995 regarding presumed or confirmed fault trajectories. New insights were gained regarding the relationships between Formica nest sites, gas-permeable faults, and groundwater levels on narrow mountain ridges with steep relief. Here, the lateral emission of CO₂ depends on the groundwater level and does not occur vertically directly above the fault. C- and H-isotope data of CO₂ and CH₄ do not show a consistent source. While methane is mainly derived from biological production by Archaea in the upper crust and in swamp areas, CO₂ mostly originates from the mantle. The results of the investigations revealed that a multitude of geological and ecological factors must be considered for the interpretation of the occurrences of Formica sites northwest of Tuttlingen. These factors confer a distinct originality to this region, contributing not only to an enhanced understanding of site conditions but also furnishing information regarding environmentally relevant gas emissions.

Soil organic matter (SOM) is essential for nutrient cycling and soil carbon (C) accumu-lation, both of which are heavily influenced by the quality and quantity of plant litter. Since SOM dynamics in relation to plant diversity are poorly understood we investigated the effects of willow variety and mixture, and site on the soil C stocks, SOM chemical composition and ther-mal stability. Using pyrolysis-field ionization mass spectrometry we analysed the top 10 cm of soil from two 7-year-old experimental sites in Germany and Sweden, with monocultures and mixtures of two willow varieties (Salix spp.) belonging to different species. Overall, site had the strongest effect on SOM quality. Results showed significant variability across sites for willow identity and mixture effects on C accumulation and SOM chemistry. In the German site (Ros-tock), yearly soil C accumulation was higher (p < 0.05) for variety ‘Loden’ (1.0 Mg C ha-1 year-1) compared to ‘Tora’ (0.5 Mg C ha-1 year-1), whilst in the Swedish site (Uppsala), both varieties ex-hibited similar soil C accumulation rates of around 0.6 Mg C ha-1 year-1. Willow variety identity significantly affected SOM quality at both sites, while mixing had minor effects. Our findings emphasize the significance of site-specific context and variety or species identity in shaping soil C accumulation in willow plantations.

Abstract: The SARS-CoV-2 pandemic has reemphasized the urgent need for broad-spectrum antiviral therapies. We developed a computational workflow using scRNA-Seq data to assess cellular metabolism during viral infection. With this workflow we predicted the capacity of cells to sustain SARS-CoV-2 virion production in patients and found a tissue-wide induction of metabolic pathways that support viral replication. Expanding our analysis to influenza A and dengue viruses, we identified metabolic targets and inhibitors for potential broad-45 spectrum antiviral treatment. These targets were highly enriched for known interaction partners of all analyzed viruses. Indeed, phenformin, an NADH:ubiquinone oxidoreductase inhibitor, suppressed SARS-CoV-2 and dengue virus replication. Atpenin A5, blocking succinate dehydrogenase, inhibited SARS-CoV-2, dengue virus, respiratory syncytial virus, and influenza A with high selectivity indices. In vivo, phenformin showed antiviral activity against SARS-CoV-2 in a Syrian hamster model. Our work establishes host metabolism as druggable for broad-spectrum antiviral strategies, providing invaluable tools for pandemic preparedness.

Based on the dynamic strength variation mechanism of concrete under complex loading conditions, two approaches were devised: numerical testing and CT scanning, guided by the principle of minimizing energy dissipation. A methodology for calculating concrete's failure area and measuring its strength was developed. The analysis delves into the mechanisms behind failure patterns and variations in concrete specimen strength, focusing on crack initiation, development, and the resultant failure surface formed by crack propagation, along with the stress distribution in concrete specimens subjected to diverse loading conditions. Through evaluating the strength and computed failure area of concrete specimens, it is evident that the loading method influences both the strength and failure area of concrete specimens. In general, a larger failure area correlates with a higher measured strength.

Fowlpox virus (FPV) has been used as a vector for many years. To date, surprisingly, very little data exist on the persistence of fowlpox vaccines in chicken tissues, or what kind of immune cells respond to the vaccination at the site of inoculation. Although both humoral and cellular mediated immunity (CMI) play a part in overall immunity against FPV, little is known regarding the cell-mediated immune responses to FPV infection. The main aim of this paper was to measure persistence of the recombinant fowlpox vaccine in the skin tissues following vaccination. The results showed that the recombinant FPVs do not persist for long, and are cleared by 6 days post-vaccination (dpv). The response of immune cells (macrophages, B cells, CD4+ and CD8+ T cells) that infiltrating the site of vaccination was estimated.

Solar photovoltaic (PV) generation suffers from multiple serious issues, for example shading effects directly affect the performance of installed PV arrays. By studying these issues, it can play a key role in improving the limitations and performance of PV panels. The study of PV arrays under partial shading conditions is mentioned in many papers as a part of other studies and as an independent phenomenon. Therefore, it is essential to improve these studies and update them with new research and study this problem in detail to know how to limit the effects of partial shading irradiance conditions on PV arrays performances, including economical aspects. This paper proposes to study the effects of different partial shading irradiance conditions for a PV array in various configurations. The analysis is proved in detail through the simulation of the proposed PV array in the Matlab/Simulink environment. The obtained results show the performances of interconnected PV arrays under different partial shading irradiance and temperature conditions, including the solar array I-V and P-V characteristics. In addition, different PV array configurations with and without bypass and blocking protection diodes improve and minimize the effect of partial shading conditions and avoid the reductions in output power.

Huperzine A is an herbal reversible inhibitor of Acetylcholinesterase (AChE). A molecular docking analysis on Huperzine A molecule has been carried out to understand its structure, conformational flexibility, intermolecular interaction and the binding affinity in the active site of AChE enzyme. Further, the charge density distribution of huperzine A molecule (lifted from the active site of AChE) was determined from the high level quantum chemical calculations coupled with charge density analysis. The binding affinity of Huperzine A towards AChE was calculated from the molecular docking; the lowest docked energy is -8.46 kcal/mol. In the active site, huperzine A molecule interacts with acyl binding pocket-Phe330 of AChE, that is, the bicyclo ring group of huperzine A forms an intermolecular interaction with the oxygen atom of main chain of the amino acid residue Phe330 at the distances 3.02 and 3.25 Å respectively. On the other hand, a gas phase study on huperzine A molecule also performed using HF and DFT (B3LYP) methods with the basis set 6-311G**. The molecular structure, conformation, and the charge density distribution of huperzine A molecule in the gas phase have determined using quantum chemical calculations and the charge density analysis. The comparative studies between the gas phase and the active site forms of huperzine A molecule, explicitly reveals the degree of conformational modification and the charge density redistribution of huperzine A when present in the active site. The dipole moment of the molecule in the active site is 6.85 D, which is slightly higher than its gas phase value (5.91 D). The electrostatic potential (ESP) surface of active site molecule clearly shows the strong electronegative and positive ESP regions of the molecule, which are the expected strong reactive locations of the molecule.

The degree of ore rock fragmentation of mine blasting is an important index for evaluating the effect of engineering blasting. In order to study the effect of millisecond delayed blasting on the internal fragmentation of the ore rock, LS-DYNA numerical simulation software was used to obtain the damage characteristics of the ore rock in the blasting area using the RHT model. The Mohr-Coulomb strength damage criterion was applied to analyze the internal stress state of the ore rock, and the effects of 25ms, 50ms and 75ms delay time conditions on ore rock fragmentation were studied. The results show that, within a certain range of delay time, the degree of rock fragmentation increases with the increase of delay time. The stress state in the ore rock due to blasting is strengthened with the increase of delay time in the direction of the blast hole, which shows that the stress concentration is strengthened from the excavation face to the interior of the ore rock. The damage and the degree of fragmentation show a characteristic relationship of 25ms＜50ms＜75ms, which is verified by carrying out blasting experiments on site.

The optimization of photovoltaic (PV) systems is vital for enhancing efficiency and economic viability, especially under Partial Shading Conditions (PSCs). This study focuses on the development and comparison of traditional and advanced algorithms, including Perturb and Observe (P&O), Incremental Conductance (IC), Fuzzy Logic Control (FLC), Grey Wolf Optimization (GWO), Particle Swarm Optimization (PSO), and Artificial Neural Networks (ANN), for efficient Maximum Power Point Tracking (MPPT). Simulations conducted in MATLAB/SIMULINK evaluated these algorithms’ performance under various shading scenarios. The results indicate that while traditional methods like P&O and IC are effective under uniform conditions, advanced techniques, particularly ANN-based MPPT, exhibit superior efficiency and faster convergence under PSCs. The study concludes that integrating AI and ML into MPPT algorithms significantly enhances the reliability and efficiency of PV systems, paving the way for broader adoption of solar energy technologies in diverse environmental conditions. These findings contribute to advancing renewable energy technology and support the green energy transition.

The paper presents a proposal for an in-house mathematical model of a liquid flat-plate solar collector. The proposed model is a one-dimensional distributed parameter model enabling simulations of the collector operation under arbitrarily variable boundary conditions. The model is based on the solution of energy balance equations for all components of the collector. The formulated differential equations are solved iteratively using an implicit difference scheme. In order to obtain a stable numerical solution, it is necessary to use appropriate steps of the time and spatial division. These were found by comparing the results obtained from the model with the results of the analytical solution available in the literature for the transient state, which constitutes the novelty of the present study. The accuracy of the results obtained from the model was verified experimentally by comparing the measured and the calculated history of the fluid temperature at the outlet of the collector. The calculation of the collector time constant is proposed in the paper as an example of the model practical application. The results of the time constant calculation were compared with the values obtained experimentally on the test stand. This is another novelty of the presented research. The analysed collector instantaneous efficiency was then calculated for selected outdoor conditions. The presented mathematical model can also be used to verify the correctness of the collector operation. Comparing, on an ongoing basis, the measured and the calculated values of the fluid temperature at the collector outlet, conclusions can be drawn about the process of solar glass fouling or glycol gelling. The model's simplicity and the low computational demands enable such comparisons in an online mode.

The over use of pharmaceutical compounds, essentially antibiotics, led to an increase of their concentrations in aquatic ecosystems. In this study, the white-rot fungus Coriolopsis gallica (high-laccase-producing fungus) was investigated for the biodegradation of ampicillin (AMP) under different cultivation conditions. The biotransformation of the antibiotic was confirmed by means of high-performance liquid chromatography (HPLC), and the antibacterial activity was evaluated via the bacterial growth inhibition agar well diffusion method using Escherichia coli as an ampicillin-sensitive test strain. The results showed that AMP (50 mg L-1) was totally removed by C. gallica after 6 days of incubation in a liquid medium. The antibiotic removal rate was maximal with a fungal culture aged 9 days. Such a culture achieved the removal of a higher concentration of up to 500 mg L-1 of ampicillin in 3 days. This higher antibiotic removal rate was concomitant with the maximal laccase production in culture supernatant. In addition, four consecutive doses of 500 mg L-1 of ampicillin were transformed by the same fungal culture in 24 days. After that, the fungus was unable to remove the antibiotic. The measurement of ligninolytic enzyme activity showed that laccase of C. gallica might participate in the biotransformation of AMP.

Perilla frutescens leaves are expected to exhibit antioxidant activity and amyloid-β (Aβ) aggregation inhibitory activity due to the presence of polyphenol-type compounds, etc. These activities fluctuate daily; however, measuring the contents of constituents and functionalities is cumbersome and unsuitable for instantaneous measurements in the field. In this study, we developed a facile method to analyze the activity and content of the components in leaves on-site based on the fluorescence spectra obtained by irradiating the perilla leaves with excitation light. The constituent contents (Chlorophyl (Chl), Total polyphenol content (TPC), Total flavonoid content (TFC), rosmarinic acid (RA) and functional properties DPPH radical scavenging activity, ferric reducing antioxidant power (FRAP), oxygen radical absorbance capacity (ORAC), Aβ aggregation inhibitory activity) were evaluated using established analytical techniques. The correlation between the fluorescence spectrum and the contents and activities was calculated using normalized difference spectral index (NDSI), ratio spectral index (RSI), and difference spectral index (DSI) analyses. We identified a predictive model with a high coefficient of determination R² ≥ 0.57 for content of the constituents, and R² ≥ 0.49 for functional properties. This allows convenient, simultaneous, and non-destructive monitoring of the constituent contents and the functionalities of perilla leave and a simple harvest-time diagnosis. The model established using this method is simple and suggesting that it can simultaneously infer the constituents and functionalities of perilla leaves.

Blockchain technology (BCT) has the potential for sustainable development, enhancing business efficiency, reducing costs, and strengthening data security. Despite its potential, adoption among small and medium-sized enterprises (SMEs) is low due to the need for significant changes in technology infrastructure and the challenge of interoperability. A cross-sectional survey was done with 226 Hong Kong SMEs. The PLS-SEM results highlighted favorable transformation conditions as the most critical factor for SMEs considering the adoption of BCT. These conditions address both internal and external readiness for adopting the disruptive strategy. Other contributing factors to BCT adoption include trust in BCT developers, perceived usefulness and ease of use, government support, and perceived security. The research results contributed to the literature on disruptive technology acceptance, adoption, transformation conditions, technology readiness, and SMEs’ technology adoption. Government-supported policies and initiatives can promote BCT adoption, including educational programs, case studies, and resources for readiness. Financial support and regulatory frameworks can further encourage adoption. BCT developers can demonstrate the value of their systems, effectively communicate potential ROI and cost savings, and provide user-friendly interfaces to increase SMEs’ intention to adopt BCT.

The Circular Bioeconomy (CBE) combines the concepts of bioeconomy and circular economy. As an alternative concept to the current fossil-based, linear economy, it de-scribes an economy based on the efficient valorization of biomass. It is regional in nature and aims to improve sustainability. An analysis of the transition process, by identifying its success criteria and assessing its impacts through the modelling of technology-specific scenarios is necessary to ensure that CBE concepts are sustainable. However, a compre-hensive consideration of regional influences on both is lacking. Based on extensive literature research and an expert survey, we (i) present a compre-hensive catalog of CBE success criteria and discuss their region-specific character and (ii) develop a methodology based on evaluation matrices that enable to match CBE technolo-gies with regions. The matrices support the evaluation of technological and regional characteristics influencing the successful CBE implementation. The results show that the success criteria "biomass resources", "technological", and "social" are perceived as highly important, and that most of the success criteria are both region- and technology-specific, highlighting the relevance of developing matrices to match them. We describe such matrices indicatively for the two broadest and most im-portant success criteria clusters “social acceptance” and “biomass supply chain”. With this, we substantiate the regional nature of CBE and raise the awareness on the importance of considering regional conditions in CBE transition processes. Furthermore, we provide practical guidance on how regional conditions can be reflected in the selection of technologies, e.g. in regional CBE technology scenarios.

We primarily investigate the existence of solutions for fractional neutral integro-differential equations subjected to Neumann-type boundary conditions, which is crucial for understanding natural phenomena. Taking into account factors such as neutral type, fractional-order integrals, and fractional-order derivatives, we employ probability density functions, Laplace transforms, and resolvent operators to formulate a well-defined concept of a mild solution for the specified equation. Following this, by integrating fixed point theorems, we establish the existence of mild solutions under more relaxed conditions.

Eotaxin-3 is a key chemokine with a relevant role in eosinophilic esophagitis, a rare chronic immune/antigen-mediated inflammatory disorder. Eotaxin-3 is a potent activator of eosinophil emergence and migration, which may lead to allergic airway inflammation. We investigated by bioinformatics tools the protein structure and the possible effects of the known variations reported in public databases. Following a procedure already established, we created a 3D model of the whole protein and modelled the structure of 105 protein variants due to known point mutations. The effects of the amino acid substitution at the level of impact on protein structure, stability, and possibly function, were detected by the bioinformatics procedure and described in detail. A web application was implemented to browse the results of the analysis and visualize the 3D models, with the opportunity of downloading the models and analyze by the own software. Among 105 amino acid substitutions investigated, the study evidenced in 44 cases at least one change in any of the investigated structural parameters. Other 6 variations are also relevant, although a structural effect is not detected by our analysis, because they substituted amino acids highly conserved, which suggests a possible function role. All these variations should be the object of particular attention, as they may induce loss of functionality in the protein.

(1) Background: a study was undertaken to determine the prevalence of chronic diseases and health conditions that affect oral health and oral health self-care among independent living older adults in rural areas of Victoria, Australia; (2) Methods: The study analysed data from the Crossroads-II project, with a total of 1407 participants aged 55 years and older. Participants self-completed questionnaires about health conditions, service use, and demographics. 572 attended a 2-hour health screening that included an assessment of prescribed medications; (3) Results: Most participants were female (55.3%), with a mean age of 69.1 (SD=9.2) years. Participants had a high prevalence of medical conditions, the most common were high blood pressure, arthritis, high lipids, hearing loss, and chronic pain. Almost all participants reported taking medications, with an average of 4.3 medications per person. Among those who attended the health screening, 78.1% were taking medications that could cause xerostomia (dry mouth); (4) Conclusions: This study provides initial information on the prevalence of medical conditions, medication usage, with potential impact on oral health of older adults living in rural Victoria. This information would be valuable for healthcare and dental workforce planning, policy development, and improving the overall well-being of this population.

Conditions under which compositions of component systems form a well-defined system-of-systems here are formulated at a fundamental level. Statement of what defines a well-defined composition and sufficient conditions guaranteeing such a result offers insight into exemplars that can be found in special cases such as differential equation and discrete event systems. For any given global state of a composition, two requirements can be stated informally as: 1) the system can leave this state, i.e., there is at least one trajectory defined that starts from the state, and 2) the trajectory evolves over time without getting stuck at a point in time. Considered for every global state, these conditions determine whether the resultant is a well-defined system and if so, whether it is non-deterministic or deterministic. We formulate these questions within the framework of iterative specifications for mathematical system models that are shown to be behaviorally equivalent to the Discrete Event System Specification (DEVS) formalism. This formalization supports definitions and proofs of the afore-mentioned conditions. Implications are drawn at the fundamental level of existence where the emergence of a system from an assemblage of components can be characterized. We focus on systems with feedback coupling where existence and uniqueness of solutions is problematic.

The Ionian Sea is a crucial intersection for various water masses in the Mediterranean. Its hydrography and dynamics play a significant role in the seawater budgets and biogeochemistry of the neighboring sub-basins. Multiple theories have been formulated to gain a better understanding of the Ionian dynamics. These theories primarily attribute the variability of the near-surface Ionian circulation to internal processes. Here, we utilize horizontal currents and temperature-salinity profiles from the Copernicus reanalysis to examine the contribution of baroclinic modes to the variability of the basin horizontal circulation. Our findings demonstrate that, although the basin vertical structure is characterized by three layers, the primary patterns of the Ionian circulation can be attributed to the first baroclinic mode. This mode, along with the barotropic mode, accounts for over 85% of the overall variability in the Ionian circulation, suggesting that only one of the three interfaces separating the different water masses in the basin is dynamically active. We estimate the depth of this interface to be about 490 m. Additionally, our analysis shows that more than 90% of the kinetic energy over the water column is localized above this interface, indicating that the deep layer of the Ionian is dynamically nearly inert.

Noninvasive brain stimulation technique can be used for modulation of motor behaviors such as reaction time (RT). The main aim of this study was to investigate whether RT during a sequential visual isometric pinch task (SVIPT) can be affected by anodal transcranial direct current stimulation (a-tDCS) over three different stimulation sites such as dorsolateral prefrontal cortex (DLPFC), primary motor cortex (M1) or posterior parietal cortex (PPC). We also aimed to assess if stimulation of these cortical sites affect the transfer of learning during SVIPT. A total of 48 right-handed healthy participants were randomly assigned to one of the four a-tDCS groups: 1) left M1, 2) left DLPFC, 3) left PPC and 4) sham. A-tDCS was applied concurrent with SVIPT in which the participants were precisely controlled their forces to reach seven different target forces from 10 to 40% of maximum voluntary contraction (MVC) presenting on a computer screen with right dominant hand. Four test blocks were randomly performed at baseline and 15 min after the intervention including sequence and random blocks with either hand. Our results showed significant differences between a-tDCS groups on ratio RT in the sequence blocks of both the right trained (P = .041) and left untrained hands (P = .023) for target forces of 15% and 30 % of MVC, respectively. In sequence blocks, M1 showed significant elongation in ratio RT for the target force of 15% and 30 % MVC compared to PPC and Sham groups in the right hand. In sequence blocks with left hand, this negative effect were found between M1-DLPFC and M1-Sham groups. In random blocks, no significant differences were found among four groups at each target forces for the left hand while there were significant differences for 15% (P =. 04) and 40% MVC (P =. 035) in the right hand. Our findings suggest that three different stimulation sites (DLPFC, M1 or PPC) were differentially affected by a single session of a-tDCS at some target forces during SVIPT. The effects of a-tDCS on ratio RT were transferred in the left untrained hand for sequence blocks but not random blocks. Further research is needed to understand fundamental aspects of these main areas of the brain on temporal processing in a precision control task such as SVIPT.

The agronomic characteristics of Cenchrus purpureus were assessed through a randomized block experimental design with seven accessions (Taiwan grass, King grass, Elephant grass, Merkeron, CT-115, Purpule grass and Maralfalfa) as treatments and four replications research was carried out at the Instituto Tecnológico Superior de Tantoyuca, in 2019 and 2020, under rainfed conditions. Sowing density was established at 36 tillers in 25 m2. Green and dry matter yield, daily rates of dry matter accumulation in leaves, leaf/stem ratio, height, leaf area index and cutting frequency were assessed. Rainfall amount, temperature, relative humidity and global radiation levels were recorded to assess their effect on the evaluated variables. One-way ANOVA and multivariate analysis techniques, such as multiple linear regression (MLR), Clustering, and Principal component analysis (PCA) with the Statistica V7 software, were used. The leaf area index was greatest (p &lt; 0.05) on the dry season. Green and dry matter yield were greatest in Maralfalfa (p &lt; 0.05). Variation in the results is attributed to weather phenomena; nonetheless, Elephant grass and Maralfalfa showed the highest yields. Quality parameters must be evaluated to identify those grasses with the best attributes.

The nutrient absorption and utilization efficiency in the roots of seedlings are beneficial for increasing crop yield. Creating marker assisted selection for wheat root traits can assist wheat breeders in choosing robust roots to maximize nutrient uptake. Exploring and identifying the effect of different nitrogen applications on RSA is of great significance for breeding nitrogen efficient wheat varieties. In this study, A total of 243 wheat varieties native to the Yellow and Huai Valley regions of China were utilized for genome-wide association studies (GWAS). Furthermore, a recombinant inbred line (RIL) population of 123 lines derived from the cross between Avocet and Chilero was utilized for linkage examination and confirmation of the hereditary loci distinguished by GWAS. Five RSA traits include the relative number of root tips (RNRT); relative total root length (RTRL); relative total root surface area (RTRS); relative total root volume (RTRV) and relative average root diameter (RARD) where evaluated under two N conditions—normal N (NN) supply and low N (LN)—to characterize the NUE of each accession. GWAS and linkage analysis were performed by integrating data from the wheat 660k single nucleotide polymorphism (SNP) chip and diversity arrays technology (DArT) to identify genetic loci associated with RSA. The results showed that based on the ratio of RSA related traits under two N supply conditions, a total of 598 SNP markers, which are significantly associated with RSA related traits, were detected at 160 genetic loci by GWAS. A total of 10 QTL loci related to RSA were dis-covered and identified by linkage mapping. In which, three significant RSA related Quantitative Trait Locus (QTL) were identified, namely qRtrl-3D, qRnrt-3D, and qRtrl-7D. The study has the potential to enhance the effectiveness of selecting root traits in wheat breeding programs, offering valuable insights into the genetic underpinnings of nitro-gen use efficiency (NUE) in wheat. This could lead to the creation of NUE wheat varieties by implementing focused breeding strategies

Rising organic charge in northern freshwaters is attributed to increasing levels of Dissolved Natural Organic Matter (DNOM) and shifts in water chemistry. Organic charge concentration may be determined by charge balance calculations (Org.-) or modelled (OAN-) using the conceptual Oliver and Hruška models based on the density of weak acid functional sites (SD) present in DNOM. The charge density (CD) is governed by the SD and protonation and complexation reactions on the functional groups. The models use this SD as a key parameter in empirically fitting the model to Org.-. Utilizing extensive datasets of water chemistry, this study shows that spatial and temporal differences in SD and CD are influenced by variations in the humic-to-fulvic ratio of DNOM and the organic aluminum (Al) complexation, as well as the mole fraction of CD to SD governed by the acidity. Site median SD obtained for 44 long-term monitored acid-sensitive lakes was 11.1 and 13.9 µEq/mg C for the Oliver and the Hruška model, respectively. During the 34 years of monitoring the CD increased by 70%, likely due to rising pH and declining Al complexation with DNOM. Present-day median SD values for the Oliver and Hruška models in 16 low-order streams are 13.8 and 15.8 µEq/mg C, respectively, and 10.8 and 12.5 µEq/mg C, respectively, in 10 high order rivers.

Maize is an important staple food crop in sub-Saharan Africa (SSA). However, the average grain yield on farmers’ fields falls considerably short of the demand of the region’s population. In addition, the normal endosperm maize widely consumed in SSA is deficient in vitamin A. Drought, a consequence of climate change, is a major constraint to maize production, resulting in seasonal low grain yield in farmers’ fields. The objectives of this study were to assess the performance of newly developed extra-early maturing provitamin A hybrids under managed drought and well-watered conditions, compare the outcomes of multiple trait base-index and multi-trait genotype-ideotype distance index selection procedures, and identify drought-tolerant hybrids with stable performance across contrasting environments for commercialization in SSA. One hundred and ninety provitamin A hybrids and six checks were evaluated under managed drought and well-watered conditions at Ikenne for two seasons between 2021 and 2023. A 14*14-lattice design was used for the field evaluations under both research conditions. Drought stress was achieved by the complete withdrawal of irrigation water 25 days after planting. Results revealed significant differences among the hybrids under drought and well-watered conditions. Grain yield, ears per plant, and plant aspect under managed drought were correlated to the same traits under well-watered conditions suggesting that the expression of these traits is governed by common genetic factors. Twenty-nine hybrids were identified as top-performing drought-tolerant hybrids by the multiple trait base index and multiple-trait genotype–ideotype distance index. Of the selected outstanding 29 hybrids, 34% were derived from crosses involving the tester TZEEIOR 197, demonstrating the outstanding genetic potential of this inbred line. Further analysis of the 29 selected hybrids revealed TZEEIOR 509 × TZEEIOR 197 as the hybrid that combined the most drought-tolerant adaptive traits. However, the hybrids TZEEIOR 526 × TZEEIOR 97, TZEEIOR 384 × TZEEIOR 30, TZEEIOR 515 × TZEEIOR 249, TZEEIOR 510 × TZEEIOR 197, TZEEIOR 479 × TZEEIOR 197, and TZEEIOR 458 × TZEEIOR 197 were identified as the most stable hybrids across drought and well-watered conditions. These hybrids should be extensively tested in multi-location trials for deployment and commercialization in SSA.

Sustainability is a characteristic manifested in the ability to maintain the necessary level of performance for construction companies when risk factors arise during the implementation of investment and construction projects. The risk factors that arise during the implementation of in-vestment and construction projects differ in nature, degree of influence, and other characteristics. Ignoring these factors and measures to manage them often leads to critical consequences in the form of disruptions in the timing of work. Risk is a combination of the probability and consequences of the occurrence of adverse events. The article considers the concept of risk as a potential possibility of occurrence of adverse situations and related consequences when exposed to these factors. Risk factors are characterized by surprise, discreteness of changes, the presence of threshold values, upon reaching which a transition to a different mode of operation is required. The article discusses the risk factors arising at the construction stage, their classification. A methodology has been developed that includes conducting a survey in the form of a questionnaire in order to collect information about risk factors that affect the implementation of investment and construction projects. Experts with experience in the construction sector were involved in the survey. The processing of the survey results made it possible to assess the significance of various risk factors in investment and construction projects. Thus, statistical and expert methods were used in the study. The results showed that financial, technical, legal, economic, managerial and natural factors have the greatest impact on investment and construction projects. It is recommended to pay special attention to the listed factors when developing measures aimed at preventing risks and their consequences. The methodology described in the study can be used by construction companies in strategic planning. The analysis of the stability of construction companies, depending on their use of various ways to counteract risk factors, allowed us to develop a number of practical recommendations to reduce the impact of the studied factors on achieving the goals of investment and construction projects.

The SARS-CoV-2 high infectivity is due to the functional polybasic furin cleavage site in the S protein. How it was acquired is unknown. There are two challenges to face: (i) an evolutionary model, to fit the origin of the coronavirus; and (ii) a molecular mechanism for the site acquisition. Here we show genomic fingerprints which are specific of Pangolin-CoVs, Bat-SARS-like (CoVZC45, CoVZXC21), bat RatG13 and human SARS-CoV-2 coronaviruses. This, along with phylogenetic analysis, we found that these species have the same evolutionary origin in the bat, including a genetic recombination of S gene between Pangolin-CoV (2017) and RatG13 ancestors. However, this does not explain why SARS-CoV-2 is the only of them with the furin site, which consists in four amino acid (PRRA) motif. The Arginine doublet is encoded by CGGCGG codons. Surprisingly, none of the Arginine doublet of other furin site of viral proteins from several type of viruses, are encoded by the CGGCGG codons. This makes it difficult to consider a virus recombination as mechanism for the PRRA acquisition. The origin of SARS-CoV-2, is the origin of the recognition cleavage site. The bat coronavirus RaTG13 appears to be the closest relative of the SARS-CoV-2, but was isolated in 2013. So, new RatG13 samples would provide insights into the acquisition of the polybasic motif.

In arid and semi-arid regions like Tunisia, irrigation water is typically saline, posing a soil and crop salinization risk and yield reduction. This research aims to study the combined effects of soil matric and osmotic potential stresses on tomato root water uptake. Plants were grown in pot and field experiments in loamy-clay soils and were irrigated with three different irrigation water qualities: 0, 3.5, and 7 dS/m. The Hydrus-1D model was used to simulate the combined dynamics of subsurface soil water and salts. Successful calibration and validation of the model against measured water and salt profiles enabled the examination of the combined effects of osmotic and matric potential stresses on root water uptake. Relative yields, indirectly estimated from actual and potential transpiration, indicated that the multiplicative stress response model effectively simulated measured yields and the impact of saline water irrigation on crop yields. The gradual salinization of the root zone further evidenced this effect. The scenario considering a temperature increase of 2°C had no significant impact on crop yields in the pot and field experiments.

This study presents the chemical synthesis, purification, and characterization of a novel non-natural synthetic amino acid. The compound was synthesized in solution, purified, and characterized using NMR spectroscopy, polarimetry, and melting point determination. Dynamic Light 22 Scattering (DLS) analysis demonstrated its ability to form aggregates with an average size of 391 nm, extending to low micrometric sizes. Furthermore, cellular biological assays revealed its ability to enhance fibroblast cell growth, highlighting its potential for tissue regenerative applications. Circular dichroism (CD) spectroscopy showed the ability of the synthetic amino acid to bind serum albumins (using bovine serum albumin (BSA) as a model), and CD deconvolution provided insights into the changes in secondary structures of BSA upon interaction with the amino acid ligand. Additionally, molecular docking using HDOCK software elucidated the most likely binding mode of the ligand inside the BSA structure. We also performed in silico oligomerization of the synthetic compound in order to obtain a model of aggregate to investigate computationally. More in detail, in the dimer formation achieved by molecular self-docking, two distinct poses were observed, corresponding to the lowest and comparable energies, with one pose exhibiting a quasi-coplanar arrangement characterized by a close alignment of two aromatic rings from the synthetic amino acids within the dimer, suggesting the presence of π-π stacking interactions. In contrast, the second pose displayed a non-coplanar configuration, with the aromatic rings oriented in a staggered arrangement, indicating distinct modes of interaction. Both poses were further utilized in the self-docking procedure. Notably, iterative molecular docking of amino acid structures resulted in the formation of higher-order aggregates, with a model of a 512-mer aggregate obtained through self-docking procedures. This model of aggregate presented a cavity capable of hosting therapeutic cargoes and biomolecules, rendering it a potential scaffold for cell adhesion and growth in tissue regenerative applications. Overall, our findings highlight the potential of this synthetic amino acid for tissue regenerative therapeutics and provide valuable insights into its molecular interactions and aggregation behavior.

Monitoring the integrity of aeronautical structures is fundamental for safety. Structural Health Monitoring Systems (SHMS) perform real-time monitoring functions, but their performances must be carefully assessed. In this work the damage detection performances of a strain-based SHMS, were evaluated on a composite helicopter rotor blade root. The SHMS monitored the bonding between the central core and the surrounding antitorsional layer. A damage detection algorithm was trained through Finite Element analyses performed on the component. The effects of the loads variability and of damages were decoupled by including a load recognition step in the algorithm. Load recognition was accomplished in different ways: version#1 adopted an Artificial Neural Network (ANN) trained on blades in pristine condition; version#2 was trained also on damaged blades; version#3 adopted a calibration matrix method. Anomaly detection, damage assessment, and localization were performed by using an ANN. Results showed a higher load identification and anomaly detection accuracy for version#1 and version#2 compared to version#3. Gaussian noise reduced anomaly detection and damage assessment performances, and reduced damage localization accuracy for bigger damages. The damage detection performance were obtained for a fibre optic based-SHMS, including the trade-off between probability of detection and false alarm rate for different damage sizes.

Nowadays, the identification and characterization of grapevine cultivars resilient to climate and water stress while preserving quality traits is crucial for the wine industry. Therefore, the objective of this work was to characterize according to their aromatic potential 9 white and 6 red minority cultivars recently recovered from Castilla-La Mancha region (Spain), subjected at two different water deficit regimes: rainfed, with subsistence irrigation, and irrigated. For this, the varietal aromatic potential index (IPAv) and the detailed aromatic composition were analyzed by HS-SBSE-GC/MS, in extracts of two different ph. For IPAv values, red varieties did not show a clear trend with respect to irrigation. However, in white minority varieties, higher values were obtained under irrigation conditions. Thus, a clear differentiation of the minority varieties in comparison to the references was observed, primarily attributed to the content of esters and acids, in both white and red varieties. A notable contrast was observed at different pH, indicating a greater extractability of certain compounds like linalool, under more acidic conditions. This suggests that some recovered minority cultivars could be promising for cultivation in semi-arid regions with limited water, contributing to the wine sector sustainability in the future.

In recent years the number of available chemical pesticides has been significantly reduced and there have been an urgent need for discovery of alternative to chemical pesticides products, as among others the natural zeolites (zeolitic rocks). We determined the mineralogical and chemical composition of a specific and continuous layers of zeolitic rock sample (ZeotP) from Petrota, Ev-ros, Greece and evaluated its oviposition deterrent effect for the olive fruit fly Bactrocera oleae (Diptera: Terphritidae). The tested natural zeolite contained 70 wt. % Clinoptilolite, 18 wt. % Amorphous material, 7 wt. % Feldspars, 4 wt. % Cristobalite and 1 wt. % Quartz. We tested the oviposition deterrent effect of ZeotP mixed or not with an emulsifier adjuvant NU-FILM-P® in water and applied on the surface of olive fruits. The ZeotP oviposition deterrent effect for the ol-ive fly was very high under a series of tested temperatures (17°C, 20°C, 25°C and 30°C) and RHs (23%, 33%, 55%, 75%, 94%). In addition, the ZeotP residual deterrent effect after equable water spraying was high and similar to the respective effect of a pyrethroid insecticide (Decis®). Our results may contribute to an effective control of the olive fruit fly using an alternative to chemical pesticides natural zeolite (zeolitic rocks) product.

Pseudomonas donghuensis P482 exhibits broad antibacterial and antifungal activity, primarily related to the production of 7-hydroxytropolone (7-HT). However, the restricted nutritional conditions (viz. mineral medium with single carbon source) diminished the antagonistic activity of P482. In this study, we unveil profiles of the secondary metabolites from P482 and its selected mutants, using nutrient-diluted (10% tryptone soy broth, TSB) and nutrient-restricted (M9 with either 0.4% glucose or 0.4% glycerol as a sole carbon source) media to explore differences in the quantity and quality of the secondary metabolites produced. No 7-HT was found to be synthetized by P482 under restricted nutritional conditions. However, both the wild-type and the tested mutants of P482 still did express some antagonistic activity towards the plant pathogenic bacteria tested. Based on these results, we postulate that 7-HT is not the sole antimicrobial compound produced by P. donghuensis P482 and that other antimicrobials may be involved in P482 antagonistic activity under limiting-nutrient conditions.

This research paper is part of the wider project concerning the very first detailed mapping of the overall Taiwanese hydro-power plants that took place from 2013 up to 2015 and it is currently in evaluation and finalization stage. The case of Shanping hydro-power plant has been carefully studied, photographed, documented and mapped in situ. It was one of the isolated hydro-power plant projects originally built to supply the remote area with the specific designation. Shanping hydro-power plant, as well as the other units from the early hydro-power generation era in Taiwan, are considered to be the technological heritage of civil and mechanical engineering that reflects later in all the further projects up to nowadays modern Taiwanese hydro-power plants. Unfortunately, most of the hydro-power houses from the older periods were severely damaged or destroyed by natural causes which were also the case of Shanping unit. The research is trying to reconstruct the original location of the powerhouse and its supporting structures based on available historical documents, previous studies, comparative methodology, and the current on-site observation.

This study aimed to develop a laboratory-scale direct air capture unit for evaluating and comparing amine-based adsorbents under temperature vacuum swing adsorption conditions. The experimental campaign conducted with the direct air capture unit allowed for the determination of equilibrium loading, CO2 uptake capacity, and other main performance parameters of the investigated adsorbent Lewatit VP OC 1065®. The investigations also helped to understand the co-adsorption of both CO2 and H2O on the tested material, which is crucial for improving temperature vacuum swing adsorption processes. This was achieved by obtaining pure component isotherms for CO2 and H2O as well as three different co-adsorption isotherm models from literature. It was found that the weighted average dual-site Toth model emerged as the most accurate and reliable model for simulating this co-adsorption behavior. Its predictions closely align with experimental data, particularly in capturing the adsorption equilibrium at various temperatures. It was also observed that this lab-scale unit offers advantages over thermogravimetric analysis when conducting adsorption experiments on the chosen amine. The final aim of this study is to provide a pathway to develop devices for testing and developing efficient and cost-effective adsorbents for direct air capture.

Structural perturbations in the Mn4CaO5 cluster site, an oxygen-evolving complex of photosystem II, such as those induced by Ca2+/Sr2+ exchanges or Ca/Mn-removal have been known to induce long-range positive shifts (+30 mV to +150 mV) in the redox potential of the primary quinone electron acceptor plastoquinone A (QA) located 40 Å distant from the OEC. Here, we reanalyzed the crystal structure of Sr-PSII solved at 2.1 Å and compare it with the native Ca-PSII of 1.9 Å with focus on the acceptor site and report on the possible long-range interactions between the donor, Mn4Ca(Sr)O5 cluster, and acceptor sites.

Background/objectives: The health benefits of resistant starch are well known, but there have not been many studies available documenting the effect of basmati rice products containg resistant starch upon blood glucose level and lipid profile in vivo efficacy. Methods: Common cooking methods were used to prepare basmati rice products including two boiling methods viz. boiling 1 (boiling by absorption), boiling 2 (boiling in extra amount of water), frying and pressure cooking. The cooked rice were held at various temperatures and times: it was made fresh (T1), kept at room temperature (20–22°C) for 24 h (T2), kept at 4°C for 24 h (T3), and then reheated after being kept at 4°C for 24 h(T4). Next, the products' proximate composition, total dietary fibre (soluble and insoluble), resistant starch (RS), and In vitro starch digestion rate (rapidly and slowly digested starch) were examined. The effect of RS on blood glucose and lipid profile were measured in humans and rats. Histopathological study of liver and pancreas in rats were also observed. Results: The basmati rice prepared by boiling 1 and stored with T3 was found more effective to control blood glucose and lipid profile. Similarly in rats, the blood glucose level, cholesterol, triglycerides and LDL were reduced about 29.7, 37.9, 31.3 and 30.5% respectively, after consumption of basmsti rice prepared by boiling 1 and stored at T3. Conclusion: Rice products stored at 4⁰C have a high amount of resistant starh, insoluble dietary fibre, slowly digestible starch and low glycemic index. Thus helps to inhibit glycogen and lipid synthesis.

With the development of information technology and the wide application of building information modelling technology, the construction industry continues to make digital changes. Managers are trying to apply smart construction site management to promote the upgrading of production modes. We used CiteSpace software to analyze 1707 articles from China National Knowledge Infrastructure, Web of Science and Scopus to understand the current research hotspots of global scholars in this field. Results show that: (1) The number of studies on smart construction sites increases rapidly by year. Researchers from China, America and the UK have the most influential studies. (2) The cooperation between researchers and institutions is not close enough. In addition, the directions of research in the field are still scattered; (3) Chinese scholars are good at building intelligent platforms and evaluating intelligent systems from multiple perspectives. International scholars are willing to pursue technological innovation, allowing the continuous development of intelligent construction technology. (4) The applications in this field have not been popularized despite relatively perfect technology and typical cases. Future scholars should gradually improve the theoretical basis and industry standards of smart construction sites, promote the development of intelligent construction technology and establish the evaluation standards of qualified smart sites. This study will provide scholars in this field with the theoretical basis and research directions for further in-depth research, help construction companies to understand the development status and trend of smart construction sites and accelerate the intelligent transformation of construction companies.

Waste management is an unavoidable technological operation in the process of raw material extraction. The main characteristic of this technological operation is the handling of large quantities of waste material, which can amount to several hundred million cubic metres. Working with this amount of material usually requires high-capacity systems for excavation and loading, a large fleet of trucks for haulage, construction, and maintenance of a complex roads network, use of a significant area of land in order to achieve the required capacities, etc. At the same time, this operation must comply with all administrative and environmental standards. Therefore, optimising waste rock management (particularly haulage and dumping) has the potential to significantly improve the overall value of the project. This paper presents a hybrid model for the optimisation of waste dump design and site selection. The model is based on different mathematical methods (genetic algorithm, analytic hierarchy process and heuristic methods) adapted to different aspects of the problem. The main objective of the model is to provide a solution (in analytical and graphical form) for the draft waste dump design, on the basis of which the final waste dump design can be defined.

Ant rescue behaviour belongs to the most interesting subcategories of prosocial and altruistic behaviour encountered in the animal world. Several studies suggested that ants are able to identify what exactly restrains the movements of another individual and to direct their rescue behaviour precisely to that object. To shed more light on the question how precise is the identifi-cation of the source of restraint of another ant, we investigated rescue behaviour of workers of the red wood ant Formica polyctena using a new version of an artificial snare bioassay in which a nestmate victim was bearing on its body two wire loops, one placed on the petiole and acting as a snare, and an additional one on the leg. The tested ants did not direct preferentially their rescue behaviour to the snare. Moreover, the overall strategy adopted by the most active rescuers was not limited to precisely targeted rescue attempts directed to the snare, but consisted of attempts to find a solution to the victim’s problem through frequent trial-and-error switching between various subcategories of rescue behaviour. These findings highlight the importance of precise identifica-tion of cognitive processes and overall behavioural strategies for better understanding of causal factors underlying animal helping behaviour.

The longleaf pine (Pinus palustris P. Mill.) forest type occupied a much greater area in the United States prior to the arrival of Europeans, estimated to be around 37.2 million hectares. This area has been greatly reduced, and these ecosystems now occupy only about 1.2 to 1.6 million hectares. However, there has been great interest in the restoration of this forest type, and existing stands are actively managed. Thus, managers need tools to estimate site quality and ultimately productivity. Here, 16 existing equations to estimate site index and dominant height in naturally regenerated longleaf pine stands are examined for their behavior across a range of site quality and age conditions. Others can use this information as a reference to determine which equation may be best for their situation.

Inorganic polymeric materials react slowly at room temperature and as a result usually require high-temperature curing. This study used the Arrhenius equation to analyze the correlation between curing temperature and curing duration during high-temperature curing. The test results show that optimal values exist for each alkali equivalent of the activator (weight ratio of Na2O/glass powder), curing temperature, and curing duration. Extending the curing duration and increasing the curing temperature have positive effects when the alkali equivalent is lower than the optimal value. However, over-curing results in invisible cracking in the specimens. Furthermore, despite exhibiting high strength initially, the strength of specimens gradually diminishes after standing in air. To ensure the durability of glass-based geopolymer, the curing temperature should not exceed 70℃, and the curing duration should be less than one day.

Abstract: The Tropical Rainfall Measuring Mission (TRMM) and then Global Precipitation Mission (GPM) are the most important and widely used data sources in the forecasting of drought, flood, and water resources management. However, since this sensor’s data is primarily used for tropical regions, it is necessary to evaluate the accuracy for optimal use of the data across varying climatic and physiographic conditions. In this study, the accuracy of the satellite data for a span of 17 years (2000-2017) for three climatic zones has been explored using synoptic ground station data. The climates include a) arid and low rainfall, b) semi-arid and low rainfall, and c) humid and high rainfall. We evaluated satellite data accuracy in drought and wet conditions based on the Standard Precipitation Index (S.P.I.) and different seasons. For available ground control stations, 13 stations were used in the humid, seven stations in a semi-arid climate, and 12 stations in the dry climate. The results show that the monthly precipitation product of GPM (IMERG product) and TRMM (TMPA/3B43 product) overestimate the rainfall. In the arid climate, the precipitation is estimated 43%, in the semi-arid environment 50%, and in the humid weather 11% more than the ground-based data on average. Therefore, to use satellite data in different climates, it is necessary to make corrections to obtain precise results. Based on 32 ground stations, the correction coefficient has a positive relationship with average precipitation and altitude and an inverse relationship with the latitude. Further in-depth investigations showed that the accuracy of satellite data in wet conditions is higher than the accuracy of normal circumstances, and the accuracy of normal conditions is more accurate than drought conditions. Besides, the accuracy of satellite data in wet or dry conditions increases with increasing time scales. The highest accuracy was obtained for a 12-month time scale and the lowest accuracy for the 3-month time scale of drought conditions in the arid climate.

Air quality is one of the most concerning problems in major industrialized cities in the world. Prediction of future air quality is highly relevant to public health. In some big cities, multiple air quality measurement stations are deployed at different locations to monitor air pollutants, such as NO2, CO, PM 2.5 and PM 10, over time. At every monitoring time stamp t, we observe one station×feature matrix xt of the pollutant data, which represents a spatio–temporal process. Traditional methods on prediction of air quality typically use data from one station or can only predict a single pollutant (such as PM 2.5) at a time, which ignores the spatial correlation among different stations. Moreover, the air pollution data are typically highly nonstationary, We propose a de-trending graph convolutional LSTM (long short term memory) to continuously predict the whole station×feature matrix in the next 1 to 48 hours, which not only captures the spatial dependency among multiple stations by replacing an inner product with convolution, but also incorporates the de-trending signals (transform a nonstationary process to a stationary one by differencing the data) into our model. Experiments on the air quality data of the city Chengdu and multiple major cities in China demonstrate the feasibility of our method and show promising results.

The danger is still very large from cross site scripting attacks. When designing web applications We must follow as much as we can prevention rules and don’t leave any loophole to our programs. Experience is a great factor for programmers to know these attacks and for a trainee programmer is a difficult task to spot all the weak points. In this article we present a tutorial on launching an XSS attack and also we propose simple solutions.

In this review, we show the unique potential of spleen as an optimal site for islet transplantation and a source of mesenchymal stem cells. Islet transplantation is a cellular replacement therapy to treat severe diabetes mellitus, but its clinical outcome is unsatisfactory at present. One factor in clinical success of this therapy is selection of the most appropriate transplantation site. The spleen has been studied for a long time as a candidate site for islet transplantation. Its advantages include physiological insulin drainage and regulation of immunity. Recently it has also been shown that the spleen contributes to the regeneration of transplanted islets. The efficacy of transplantation is not as high as that obtained with intraportal transplantation, which is the current representative method of clinical islet transplantation. Safer and more effective methods of islet transplantation need to be established before the spleen can be effectively used in the clinic. Spleen also has an interesting aspect as a mesenchymal stem cell reservoir. The splenic mesenchymal stem cells contribute to tissue repair in damaged tissue, and thus, the infusion can be a promising therapy for autoimmune diseases, including type 1 diabetes mellitus and Sjogren’s syndrome.

Behavior analysis is a widely used non-invasive tool in the practical production routine, as the animal acts as a biosensor capable of reflecting its degree of adaptation and discomfort to some environmental challenge. Predominantly, conventional statistics use occurrence data for behavioral evaluation and well-being estimation, disregarding the temporal sequence of events. The Generalized Sequential Pattern (GSP) algorithm is a data mining method that identifies recurrent sequences that exceed a user-specified support threshold, whose potential has not yet been investigated for broiler chickens in enriched environments. Enrichment aims to increase environmental complexity with promising effects on animal welfare, stimulating priority behaviors and potentially reducing the deleterious effects of heat stress. The objective was to validate the application of the GSP algorithm to identify temporal correlations between heat stress and the behavior of broiler chickens in enriched environments through proof of concept. Video image collection was carried out automatically for 48 continuous hours, analyzing a continuous period of seven hours, from 12:00 PM to 6:00 PM, during two consecutive days of tests for chickens housed in enriched and non-enriched environments under comfort and stress temperatures. Chickens at comfort temperature showed high motivation to perform the behaviors of Preening (P), Foraging (F), Lying down (Ld), Eating (E), and Walking (W) whose sequences &lt;{Ld,P}&gt;; &lt;{Ld,F}&gt;; &lt;{P,F,P}&gt;; &lt;{Ld,P,F}&gt; and &lt;{E,W,F}&gt; were the only ones observed in both treatments. All other sequential patterns (comfort and stress) were distinct, suggesting that environmental enrichment alters the behavioral pattern of broiler chickens. Heat stress drastically reduced the sequential patterns found at the 20% threshold level in the tested environments. The behavior of lying laterally "Ll" is a strong indicator of heat stress in broilers and was only frequent in the non-enriched environment, which may suggest that environmental enrichment provides the animal with better opportunities to adapt to stress-inducing challenges, such as heat.

Violence against paramedics is widely recognized as a serious, but underreported, problem. While injurious physical attacks on paramedics are generally reported, non-physical violence is less likely to be documented. Verbal abuse can be very distressing, particularly if the harassment targets personal or cultural identities, such as race, ethnicity, gender, or sexual orientation. Leveraging a novel, point-of-event reporting process, our objective was to estimate the prevalence of harassment on identity grounds against paramedics in a single paramedic service in Ontario, Canada, and assess its potentially differential impact on emotional distress. In an analysis of 502 reports filed between February 1, 2021, through February 28, 2022, two paramedic-supervisors independently coded the free-text narrative descriptions of violent encounters for themes suggestive of sexism, racism, and homophobia. We achieved high interrater agreement across the dimensions (k=0.73-0.83), and after resolving discrepant cases, we found that 1 in 4 violent reports documented abuse on at least one of the identity grounds. In these cases, paramedics were 60% more likely to indicate being emotionally distressed than for other forms of violence. Our findings offer unique insight into the type of vitriol paramedics experience in the course of their work and its potential for psychological harm.

Geotechnical investigation is an important site characterization process in engineering construction. Excavation pits and boreholes are popular geotechnical investigation methods for accessing subsurface soil and rock characteristics. Although they are accurate, they are limited to the discrete locations where tests are carried out. The demand for 3D representation has been increasing as an alternative for improved visualization of geotechnical investigations. This study developed a procedure for 3D modelling of geotechnical investigations using open-source software. It improves 3D visualization of geotechnical investigations and characterization of accuracy and uncertainty assessment. Presently, most geotechnical investigations do not regularly report uncertainty assessment despite its importance in risk analysis of the investigations. The procedure developed in this study was tested in a proposed site for construction of an Inland Container Depot where it depicted geotechnical soil properties with more than 80% accuracy on holdout samples. It was able to model both horizontal and vertical variations of the soil properties with quantification of uncertainty. More testing and wide applications are recommended.

Multiple drugs administration is a common practice in hospitals and clinics. This is the case when heavy pathologies are treated. In this context, frequently, antivirals and antibiotics are co-administrated either simultaneously or sequentially ignoring potential incompatibilities. In this study, we focused on an antiviral (Acyclovir) and an antibiotic (Ciprofloxacin) compatibility/incompatibility when they co-administrated with special interest on the effect of drugs ratio, pH and delay. By implementing robust HPLC method, we determined the main factors leading to potential modification of concentration of one of the two drugs in the mixture. The results showed that acyclovir is quantitatively recovered in all conditions related to pH, concentration and time (up to 24 hours). However, ciprofloxacin is strongly altered in acidic and basic conditions, the quantity of ciprofloxacin and time after mixing the two drugs. The most valuable piece of information is that the ratio of acyclovir/ciprofloxacin is crucial. The latter should be calculated and managed to provide at least two fold quantity of acyclovir versus ciprofloxacin in order to maintain the administrated doses and warrant efficient therapeutic effect.

Violence against paramedics has been described as a ‘serious public health problem’ but one that remains ‘vastly underreported’, owing to an organizational culture that stigmatizes reporting – hindering efforts at risk mitigation in addition to creating a gap in research. Leveraging a novel reporting process developed after extensive stakeholder consultation and embedded within the electronic patient care record, our objective was to provide a descriptive profile of violence against paramedics in a single paramedic service in Ontario, Canada. Between February 1, 2021, through January 31, 2023, a total of 374 paramedics in Peel Region (48% of the workforce) generated 941 violence reports, of which 40% documented physical (n=364) or sexual (n=19) assault. The violence was typically perpetrated by patients (78%) and primarily took place at the scene of the 9-1-1 call (47%); however, violent behavior frequently persisted or recurred while in transit to hospital and after arrival. Collectively, mental health, alcohol, or drug use were listed as contributing circumstances in 83% of violence reports. In all, 81 paramedics were physically harmed because of an assault. On average, our data correspond to a paramedic filing a violence report every 18 hours, being physically assaulted every 46 hours, and injured every 9 days.

To estimate the progressive collapse resistance capacity of a multi-column frame tube structure with the assembled truss beam composite floor (ATBCF), the pushdown analysis, and the nonlinear dynamic analysis as well, are conducted for such a structure by using the alternate load path (ALP) method. The bearing capacities of the remaining structures at three different work conditions, which are the side middle column failure, the edge middle column failure, and the corner column failure, are individually studied, and the collapse mechanism for the remaining structures is analyzed from the aspects of the internal force redistribution and the failure mode of the second defense line. Simultaneously, the influence of the column failure time on the dynamic response of the remaining structure and the dynamic amplification coefficient are discussed. The results show that the residual bearing capacity of the remaining structure with the bottom corner column failure is higher than that of the one with the side or edge middle column failure, while the latter has a stronger plastic deformation capacity. When the ALP method is adopted to operate the progressive collapse analysis, it is reasonable to take the column failure time as 0.1 times of the first-order vertical vibration period of the remaining structure, and it is suitable to set the dynamic amplification coefficient as of 2.0, which is the ratio of the maximum dynamic displacement to the static displacement of the remaining structure under the transient loading condition.

Extracellular vesicles (EVs) carry diverse cargo of DNA, RNA, proteins, and lipids. They are crucial mediators for regulating various functions through interactions with the host. Recent investigations suggest that EVs or their constituent proteins derived from probiotics could improve the effectiveness of probiotic strains in disease management compared to probiotic strains themselves. This enhanced effec-tiveness arises from their innate antimicrobial properties, which can specifically target pathogenic mol-ecules or cells, in addition to their significant ability to regulate immune responses. Significantly, previous studies have highlighted the inhibitory potential of Lactobacillus crispatus PMC201 against Mycobacterium tuberculosis. In this study, we focused on optimizing isolation conditions for studying extracellular vesicles and proteins from anti-TB potent strains. We provide analysis results based on food-grade media (FGM) optimization and isolation methods. Nanoparticle tracking analysis (NTA) was used to determine se-cretion patterns. Proteomic analysis was performed by liquid chromatography and tandem mass spec-trometry (LC-MS/MS). A total of 64 proteins were identified in the L. crispatus PMC201 strain, particularly enriched in s-layer and splX. Questions remain about their relevance to anti-TB. This anti-tuber strain has potential as a therapeutic agent, given its significant role in intercellular killing. Further studies are needed to investigate its mechanisms of action.

Weather-related risks in aviation are one of the main causes of accidents worldwide. This article aims to analyze aviation risks resulting from adverse weather conditions, using the case study of the Pucallpa accident that occurred on August 23, 2005, in eastern Peru. In this analysis, we have determined the relationship between meteorological information and aviation risks, presented a matrix of risks associated with the most predominant meteorological variables at Pucallpa airport, and drawn up three maps of meteorological risks indicating the month of the year in which their incidence is most relevant. Finally, we conclude that it is essential to emphasize the importance of considering the prevailing weather conditions at Pucallpa airport to help mitigate the potential risks that may occur during different phases of the flight.

Effective maintenance of railways requires a comprehensive assessment of the actual condition of the construction materials involved. In this regard, Ground-Penetrating Radar (GPR) stands as a viable alternative to the invasive and time-consuming traditional techniques for the inspection of these infrastructures. This work reports the experimental activities carried out on a test-site area within a railway depot in Rome, Italy. Specifically, a 30 m-long railway section was divided into 10 sub-sections reproducing different various physical and structural conditions of the track-bed. In more detail, combinations of varying scenarios of fragmentation and fouling of the ballast were reproduced. The set-up was then investigated using different multi-frequency GPR horn antenna systems. The effects of the different physical conditions of ballast on the electromagnetic response of the material were analysed for each scenario using time- and frequency-domain signal processing techniques. Parallel to this, modelling was provided to estimate fouling content. Interpretation of results has proven the viability of the GPR method in detecting signs of decay at the network level, thereby proving this technique to be worthy for implementation in asset management systems.

There is a large body of research on determining the impact of field variability of soil on crop yields. In contrast, site-specific information about crop responses to agronomic treatments is less frequent. On-Farm Precision Experimentation (OFPE) brings important information to understand the spatial variation of crop response to agronomic practices and thus to improve agronomic decisions. The objective of this work was to investigate the spatial variability of corn yield responses to nitrogen and seed rates using OFPE in four fields in the US Midwest. Geographically weighted regression was applied to generate local regression coefficients, which were used to delineate response zones in each field. The results showed the existence of great potential to adjust the rates of these inputs according to the response of each zone identified by the proposed method. The results of this study can be applied to reevaluate expectations on variable rate prescriptions guided largely by soil and variability.

Convenient labeling of proteins is important for observing its function under physiological conditions. In tissues particularly, heptamethine cyanine dyes (Cy-7) are valuable because they absorb in near infrared (NIR) region (750 – 900 nm) where light penetration is maximal. In this work, we found Cy-7 dyes with a meso-Cl functionality covalently binding to proteins with free Cys residues under physiological conditions (aqueous environments, at near neutral pH, and 37 °C). It transpired that the meso-Cl of the dye was displaced by free thiols in protein, while nucleophilic side-chains from amino acids like Tyr, Lys, and Ser did not react. This finding shows a new possibility for convenient and selective labeling of proteins with near-IR fluorescent probes.

Construction safety is especially important because the construction industry is so important to a country's development. Significant research and practice have been conducted to mitigate potential risks during construction and improve worker efficiency. With the rapid advancement of cognitive neuroscience and the incorporation of medical technology in recent years, various wearable monitoring devices have been widely used in the construction field for real-time monitoring of workers' physical and mental status. Among these, the use of EEG (Electroencephalogram) in construction environment research allows researchers to gain insight into the physical and mental states of construction workers while performing construction tasks. This review introduces EEG technology and portable EEG devices, followed by an overview of their use in both monitoring workers' adverse reactions and identifying hazards on construction sites, providing an effective guide for EEG research in the construction field and on-site safety management.

Bifacial PV modules have become the pervasive choice for utility-scale solar photovoltaic (PV) installations. Understanding bifacial PV performance for commercial deployments is, therefore, critically important. Although there have been studies on the modeling of Bifacial PV performance, to the best of our knowledge, the comprehensive integration of racking and mounting geometry for Bifacial PV performance simulation is yet to be reported. In this work, we modeled the racking and mounting geometry for a field-deployed operational PV array. We then applied optical ray-trace simulation to study the impact of those structures on array performance. The study reveals that the support structures have a considerable impact on the rear surface irradiance and overall bifacial PV performance, amounting to as much as 30% shading in certain situations. The work analyzes the impact of installation parameters such as tilt, height, and row spacing on the bifacial PV array’s performance. Thus, a novel holistic approach to studying the sensitivity of various installation parameters’ impact on bifacial PV array performance, with the racking and mounting structure’s geometry integrated, has been demonstrated through the work. This knowledge and its practice enables site-specific design optimization for utility-scale bifacial solar PV arrays and synergistic PV applications such as agrivoltaics and carports, where maximizing power generation is not necessarily the sole objective.

ABSTRACT Background Ubiquitination plays an important role in protein post-translational processes and has been found to be involved in a number of regulatory functions including proteasome degradation, DNA repair, transcription, signal transduction, endocytosis, and sorting. As the identification of ubiquitination site is critical to furthering our understanding of the mechanism of ubiquitination, various experimental and machine learning methods have been used to conduct this task. It has been an important but challenging task to improve the accuracy of ubiquitination site prediction. In this research, we explore the possibility of improving the prediction performance of machine learning by incorporating grid search in the training process. Method We developed grid search procedures for each of six widely used machine learning methods including NB, LR, DT, SVM, LASSO, and KNN, and applied them to ubiquitination site prediction using the six PCP datasets that were previously developed. For each of the ML methods, we developed a set of values for each of the tunable hyperparameters available to the method. These sets of values then can be combined to form a large grid of hyperparameter settings, and each of these settings is used in the grid search. We integrated 5-fold cross-validation in grid search to train and test ML models and applied an additional independent validation procedure by conducting a pre-training 80-20 sample split. We evaluated the performance of the six methods by comparing them side by side for each of the six datasets. We also compared the grid search results with the results that were previously published without doing grid search. To optimize the prediction performance, we trained 1.1 million ML models in total through grid search. Results We compared the overall prediction performance of these six methods, as well as their prediction performance when working with balanced vs. imbalanced data, and large-scale vs. small-scale data. From the perspective of dataset, we find that the overall performance of every PCP dataset has been significantly improved in this study compared to the previous study, with the percentage increase of the average AUC of all six datasets ranging from 7.9% (PCP-4) up to 17.0% (PCP-1). From the perspective of method, we find that three out of four methods significantly benefit from grid search comparing to their previously published non-grid search results, with the maximum AUC improvement as high as 47% (LASSO on PCP-5), 43.3% (NB on PCP-1), and 33.7% (SVM on PCP-6). SVM overall ranks number one, followed by KNN as the number two performer based on their average AUCs on all datasets. But these two also ranked the top two (KNN 76 days and SVM 15 days) in terms of the total running time that they need to do grid search. We also find that SVM, KNN, and DT tend to handle small-scale and imbalanced datasets better, while LR, and LASSO are doing well with large-scale and balanced datasets. NB is more sensitive to data imbalance while less sensitive to the size of a dataset. Conclusions Our results show that using grid search has improved the performance of ubiquitination prediction significantly. We find that the performance of a method is closely related to its hyperparameter setting and the type of data it handles. Even though SVM is on average an outperformer, none of the methods can provide the best performance for all datasets. When sufficient computing resources are well accessible, grid search is an effective way to identify both a top performing model for a machine learning method and a suitable machine learning method for a particular dataset.

Nicotiana benthamiana plants infected with a potato virus Y isolate (PVYO) under ambient conditions of 25 °C and ~405 parts-per-million (ppm) ambient CO2 display symptoms of chlorosis, leaf curling, and stunting. However, under elevated temperature and CO2 levels (30 °C, 970 ppm), systemic viral titers decrease several-fold, and plants appear asymptomatic. Under the latter conditions we have studied how infection, drought, or both combined affect infection, drought-driven loss of leaf turgor, plant water content, stomatal conductance, metabolome, and hormone (ABA, SA, and JA) levels. We found that drought did not affect viral titers. As expected, drought decreased plant water content and stomatal conductance. Under drought conditions, infection did not alter significantly final water content or loss of leaf turgor progression, but it increased the levels of some sugars and other osmo-protectants. Infection and drought altered the levels of many components of the metabolome. Some components altered by infection were not altered by drought, but most of those altered by drought were also altered by infection. Drought increased the levels of ABA, infection increased the levels of ABA, SA, and JA, and altered their relative balance. The effects of drought and of infection on hormone levels were cumulative when combined. Thus, under ambient conditions that turn a severe infection into an asymptomatic one both, plant physiology parameters and the interplay with drought are affected.

Based on the nonlinear failure criterion and modified tangential technique, the upper bound solutions of supporting pressure on the deep tunnel face were obtained under pore water pressure conditions. The influence of parameters on the supporting pressure and collapse range was investigated according to the unlimited block failure mechanism. It is found that the upper bound solutions of supporting pressure increase with the growth of the nonlinear coefficient and pore water pressure coefficient. The collapse range of the tunnel face scales out with the increase of the nonlinear coefficient and shrinks when increasing the pore water pressure coefficient. Moreover, with the increase of the nonlinear coefficient, the impact strength on supporting pressure and collapse range declines gradually. According to the calculating results, it is manifest that both the pore water pressure and nonlinear criterion factors have negative impacts on the stability of the tunnel face. Thus, more attention should be paid to these parameters to ensure face stability in deep tunnel construction.

This survey is part of a Hungarian Research OTKA project that examines the vegetation of sandy grasslands along the Danube. During this study, two grass species, Festuca wagneri and Festuca tomanii, were identified as potentially suitable for urban planting and turf establishment based on preliminary research. Our aim was to determine the germination success of seeds from aesthetically selected individuals and to identify the soil types on which they germinate most effectively. This information could be crucial for future cultivation efforts. From the collected Festuca individuals, were analyzed 30 specimens of each taxon under garden conditions and selected the indi-viduals for germination. The Festuca tomanii individuals were uniform, so we selected only 5 individuals. The Festuca wagneri individuals were categorized into three groups: upright, spreading, and low types. It was assumed that Festuca species seeds would germinate better in sandy soils. To test this, seeds from ten Festuca wagneri and five Festuca tomanii individuals, selected based on aesthetic criteria, were sown in six different substrates: a sand-peat mixture, sand, coconut fiber, peat, a coconut fiber-sand mixture, and native sandy soil. Contrary to expectations, the growth and germination rates of seeds sown in peat and coconut fiber substrates were higher than those in native sandy soil. These results suggest that Festuca seeds germinate better on substrates resembling dead plant debris with a peat-like structure or on the surface of live mosses, rather than on bare sand. Among the examined individuals, the seeds from the spreading Festuca wagneri group exhibited the highest germination rate, making this group particularly suitable for urban environments. Addi-tionally, one of the upright Festuca wagneri individuals showed the highest growth rate and should also be considered for urban planting. In contrast, despite their uniform appearance, the Festuca tomanii individuals did not demonstrate similar germination trends. In fact, the seeds from two clumps did not germinate at all, indicating that further selection is necessary.

Abstract: Formation of DNA adducts is a key event for a genotoxic mode of action and its formation is often use as surrogate for mutation and cancer. Interest in DNA adducts are twofold, first, to demonstrate exposure, and second, to link DNA adduct location to subsequent mutations or altered gene regulation. High chemically specific mass spectrometry methods have been established for DNA adduct quantitation and elegant bio-analytic methods utilizing enzymes, various chemistries, and molecular biology methods to visualize the location of DNA adducts. Traditionally, these highly specific methods cannot be combined, and the results are incomparable. Initially developed for single-molecule DNA sequencing, nanopore-type technologies are expected to enable simultaneous quantitation and location of DNA adducts across the genome. We will briefly summarize the current methodologies for state-of-the-art quantitation of DNA adduct levels and mapping of DNA adducts and describe novel single-molecule DNA sequencing technology that is expected to achieve both measures simultaneously. Emerging technologies are expected to soon provide a comprehensive picture of the exposome and identify gene regions susceptible to DNA adduct formation.

Let $S=\left(s_1, \ldots, s_n\right)$ be a finite sequence of integers. Then $S$ is a Gilbreath sequence of length $n$, $S\in\mathbb{G}_n$, iff $s_1$ is even or odd and $s_2, \ldots, s_n$ are respectively odd or even and $\min\mathbb{K}_{\left(s_1, \ldots, s_m\right)}\leq s_{m+1}\leq\max\mathbb{K}_{\left(s_1, \ldots, s_m\right)}\forall m\in\left[\left.1, n\right)\right.$. This, applied to the order sequence of prime number $P$, defines Gilbreath polynomials and two integer sequences A347924 \cite{oeisA347924} and A347925 \cite{oeisA347925} which are used to prove that Gilbreath conjecture $GC$ is implied by $p_n-2^{n-1}\leqslant\mathcal{P}_{n-1}\left(1\right)$ where $\mathcal{P}_{n-1}\left(1\right)$ is the $n-1$-th Gilbreath polynomial at 1.

Fragile X syndrome (FXS) is a genetic disorder caused by a mutation in the fragile X messenger ribonucleoprotein 1 (FMR1) gene and known to be a leading cause of inherited intellectual disability globally. It results in a range of intellectual, developmental, and behavioral problems. Fragile X premutation associated conditions (FXPAC), also caused by a smaller CGG expansion (55 to 200 CGG repeats) in the FMR1 gene, is linked to other conditions that increase morbidity and mortality for affected persons. Limited research has been conducted on the burden, characteristics, diagnosis, and management of these conditions in Africa. This comprehensive review provides an overview of the current literature on FXS and FXPAC in Africa, epidemiology, clinical features and challenges faced, such as discrimination against affected persons, limited awareness and research, poor access to resources and genetic services and treatment. It further provides an in-depth analysis of the existing worldwide data for the diagnosis and treatment of these disorders. This review will improve understanding of FXS and FXPAC in Africa by incorporating existing knowledge, identifying research gaps, and potential topics for future research to enhance the well-being of individuals and families affected by FXS and FXPAC in the region.

Most methods for measuring environmental lead (Pb) content are time consuming, expensive, hazardous, and restricted to specific analytical systems. To provide a facile, safe tool to detect Pb, we created pMet-lead, a portable fluorescence resonance energy transfer (FRET)-based Pb biosensor. pMet-lead comprises a 3D-printed frame housing a 405-nm laser diode — an excitation source for fluorescence emission images (YFP and CFP) — accompanied by optical filters, a customized sample holder with a Met-lead 1.44 M1 (the most recent version)-embedded biochip, and an optical lens aligned for smartphone compatibility. Measuring the emission ratios (Y/C) of the FRET component enables Pb detection with a dynamic range of nearly 2 (1.96), pMet-lead/Pb dissociation constant (K_d) 45.62 nM, and limit of detection 40 nM (0.832 μg/dL, 8.32 ppb). To mitigate earlier problems with lack of selectivity for Pb vs. zinc, we preincubated samples with tricine, a low-affinity zinc chelator. We validated pMet-lead measurements of characterized laboratory samples and unknown samples from six regions in Taiwan by inductively coupled plasma mass spectrometry (ICP-MS). Notably, two unknowns had Y/C ratios significantly higher than that of the control (3.48 ± 0.08 and 3.74 ± 0.12 vs. 2.79 ± 0.02), along with Pb concentrations (10.6 ppb and 15.24 ppb) above the WHO-permitted level of 10 ppb in tap water, while the rest four unknowns showing no detectable Pb upon ICP-MS. These results demonstrate that pMet-lead provides a rapid, sensitive means for on-site Pb detection in water from the environment and in living/drinking supply systems to prevent potential Pb poisoning.

There is growing recognition in research and policy of a mental health crisis among Canada’s paramedics but despite this, epidemiological surveillance of the problem is in its infancy. Just weeks before the emergence of the COVID-19 pandemic, we surveyed paramedics from a single, large, urban paramedic service in Ontario, Canada to assess for symptom clusters consistent with Post-Traumatic Stress Disorder (PTSD), major depressive disorder, and generalized anxiety disorder and to identify potential risk factors for each. In total, we received 589 completed surveys (a 97% completion rate) and found that 11% screened positive for PTSD, 15% for depression, and 15% for anxiety, with 1 in 4 active-duty paramedics screening positive for any of the three as recently as February 2020. In adjusted analyses, the risk of a positive screen varied as a function of employment classification, gender, self-reported resilience, and previous experience as a member of the service’s peer support team. Our findings support the position that paramedics screen positive for mental disorders at high rates – a problem likely to have worsened since the onset of the COVID-19 pandemic. We echo the calls of researchers and policymakers for urgent action to support paramedic mental health in Canada.

Important first phases in the process of implementing CO2 subsurface and ocean storage projects include selecting of best possible location(s) for CO2 storage, site selection evaluation. Sites must fulfil a number of criteria that boil down to the following basics: they must be able to accept the desired volume of CO2 at the rate at which it is supplied from the CO2 source(s); they must as well be safe and reliable; and must comply with regulatory and other societal requirements. They also must have at least public acceptance and be based on sound financial analysis. Site geology; hydrogeological, pressure, and geothermal regimes; land features; location, climate, and access, etc. can all be refined from these basic criteria. In addition to aiding in site selection, site characterization is essential for other purposes, such as foreseeing the fate and impacts of the injected CO2, and informing subsequent phases of site development, including design, permitting, operation, monitoring, and eventual abandonment. According to data from the IEA, in 2022, emissions from Africa and Asia's emerging markets and developing economies, excluding China's, increased by 4.2%, which is equivalent to 206 million tonnes of CO2 and were higher than those from developed economies. Coal-fired power generation was responsible for more than half of the rise in emissions that were recorded in the region. The difficulty of achieving sustainable socio-economic progress in the developing countries is entwined with the work of reducing CO2 emissions, which is a demanding project for the economy. Organisations from developing countries, such as Bangladesh, Cameroon, India, and Nigeria, have formed partnerships with organisations in other countries for lessons learn and investment within the climate change arena. The basaltic rocks, coal seams, depleted oil and gas reservoirs, soils, deep saline aquifers, and sedimentary basins that developing countries (Bangladesh, Cameroon, India, and Nigeria etc) possesses all contribute to the individual country's significant geological sequestration potential. There are limited or no carbon capture and storage or clean development mechanism projects running in these countries at this time. The site selection and characterization procedure are not complete without an estimate of the storage capacity of a storage location. Estimating storage capacity relies on volumetric estimates because a site must accept the planned volume of CO2 during the active injection period. As more and more applications make use of site characterization, so too does the body of written material on the topic. As the science of CO2 storage develops, regulatory requirements are implemented, field experience grows, and the economics of CO2 capture and storage improve, so too will site selection and characterisation change.

Human ether-a-go-go-related gene (hERG) potassium channel is well-known contributor to drug-induced cardiotoxicity and therefore an extremely important target when performing safety assessments of drug candidates. Ligand-based approaches in connection with quantitative structure active relationships (QSAR) analyses have been developed to predict hERG toxicity. Availability of the recent published cryogenic electron microscopy (cryo-EM) structure for the hERG channel opened the prospect for using structure-based simulation and docking approaches for hERG drug liability predictions. In recent time, the idea of combining structure- and ligand-based approaches for modeling hERG drug liability has gained momentum offering improvements in predictability when compared to ligand-based QSAR practices alone. The present article demonstrates uniting the structure-based SILCS (site-identification by ligand competitive saturation) approach in conjunction with physicochemical properties to develop predictive models for hERG blockade. This combination leads to improved model predictability based on Pearson’s R and percent correct (represents rank-ordering of ligands) metric for different validation sets of hERG blockers involving diverse chemical scaffold and wide range of pIC50 values. The inclusion of the SILCS structure-based approach allows determination of the hERG region to which compounds bind and the contribution of different chemical moieties in the compounds to blockade, thereby facilitating the rational ligand design to minimize hERG liability.

The SARS-CoV-2 polybasic furin cleavage site is still a missing link. Remarkably, the two arginine residues of this protease recognition site are encoded by the CGG codon, which is rare in Betacoronavirus. However, the arginine pair is common at viral furin cleavage sites, but are not CGG-CGG encoded. The question is: Is this genetic footprint unique to the SARS-CoV-2? To address the issue, using Perl scripts, here I dissect in detail the NCBI Virus database in order to report the arginine dimers of the Betacoronavirus proteins. The main result reveals that a group of Middle East respiratory syndrome-related coronavirus (MERS-CoV) (isolates: camel/Nigeria/NVx/2016, host: Camelus dromedarius) also have the CGG-CGG arginine pair in the spike protein polybasic furin cleavage region. In addition, CGG-CGG encoded arginine pairs were found in the orf1ab polyprotein from HKU9 and HKU14 Betacoronavirus, as well as, in the nucleocapsid phosphoprotein from few SARS-CoV-2 isolates. To quantify the probability of finding the arginine CGG-CGG codon pair in Betacoronavirus, the likelihood ratio (LR) and a Markov model were defined. In conclusion, it is highly unlikely to find this genetic marker in betacoronaviruses wildlife, but they are there. Collectively, results shed light on recombination as origin of the virus CGG-CGG arginine pair in the S1/S2 cleavage site.

Background and Objectives: The site types of Eucalyptus urophylla × Eucalyptus grandis clonal plantations in southern Yunnan were compared, aiming to provide basis for site selection and scientific plantations management. Materials and Methods: In this study, 80 standard plots were set up in the 6−9-year-old Eucalypts plantations in Pu'er City and Lincang City. Furthermore, the quantitative theory I model and canonical correlation analysis were used to analyze the relationship between dominant tree growth traits and site factors, and evaluate the growth potential of E. urophylla × E. grandis plantation. Results: The multiple correlation coefficient between 8 site factors (altitude, slope, slope level, soil thickness, slope direction, texture, soil bulk density, and litter thickness) and the quantitative growth of the dominant wood was 0.825 (P < 0.05). According to the correlation coefficient of the quantitative regression model, slope, altitude, and soil thickness were the main factors for the classification of E. urophylla × E. grandis plantations in southern Yunnan. In addition, E. urophylla × E. grandis plantations grew best downhill and mid uphill at relatively low altitude, where the soil layer was thick and composed of weathered red soil. Contrastingly, E. urophylla × E. grandis plantation growth was extremely poor in uphill sites at higher altitude, where the soil layer was thin and composed of semi-weathered purple soil. Furthermore, total N, and available B, Cu, and Zn content, as well as soil organic matter content in the soil had a great influence on the growth of E. urophylla × E. grandis. Conclusions: Nitrogen and phosphate fertilizer as well as trace elements such as B, Zn, and Cu can be properly applied in middle- and low-yield forests to promote the growth and development of E. urophylla × E. grandis plantations.

The three-axes Doppler sodar Latan-3 operated on an oceanographic stationary platform in the coastal zone of the Black Sea in June 2015. The platform is located 450 meters offshore from the southern coast of the Crimea Peninsula in the region of Katsiveli (44.39°N, 33.99°E). The water depth at the site is about 30 meters. The atmospheric boundary layer (ABL) typical for the mediterranean seas was observed when the wind is from the sea. The physical processes typical for the coastal mountain terrain was observed when the wind was from the shore. Complex measurements of the ABL parameters were performed using a sodar. Auxiliary measurements of the ABL parameters were performed using a temperature profiler and an ultrasonic thermometer-anemometer. Observations were made mostly during a fair weather with a pronounced diurnal course of meteorological parameters. Sodar data analysis revealed a strong wave activity in the ABL. Internal gravity waves with amplitudes of up to one hundred meters were regularly observed in a layered turbulence structure under stable conditions. Various forms of Kelvin-Helmholtz billows were observed at the interface between the sea breeze and the return flow aloft and in the low level jets.