Freezing of Gait (FOG) is an impairment that affects the majority of patients in the advanced stages of Parkinson’s Disease (PD). FOG can lead to sudden falls and injuries, negatively impacting the quality of life for the patients and their families. Rhythmic Auditory Stimulation (RAS) can be used to help patients recover from FOG and resume normal gait. RAS might be ineffective due to the latency between the start of a FOG event, it’s detection and initialization of RAS. We propose a system capable of both FOG prediction and detection using signals from tri-axial accelerometer sensors that will be useful in initializing RAS with minimal latency. We compared the performance of several time frequency analysis techniques, including moving windows extracted from the signals, handcrafted features, Recurrence Plots (RP), Short Time Fourier Transform (STFT), Discreet Wavelet Transform (DWT) and Pseudo Wigner Ville Distribution (PWVD) with Deep Learning (DL) based Long Short Term Memory (LSTM) and Convolutional Neural Networks (CNN). We also propose three Ensemble Network Architectures that combine all the time frequency representations and DL architectures. Experimental results show that our ensemble architectures significantly improve the performance compared with existing techniques. We also present the results of applying our method trained on publicly available dataset to data collected from patients using wearable sensors in collaboration with A.T. Still University.

The aim of this study was to investigate and effect of application of different conditions of freeze-drying on the kinetics of process and the sorption properties of dried apples. Slices of apple were frozen and subjected to freezing-drying process with different combination of a shelf temperature (-20, 10, 20, 30°C) and pressure (37, 63, 103, 165 Pa). During the freeze-drying, the temperature in the centre of material was recorded. The moisture content in dried material and changes of water content dried apples stored at humidity of 75.3% were obtained. The Midilli et al. model was used to describe drying kinetics of the freeze-drying with good fit. Drying time decreased from 660 (variant with a constant shelf temperature of 30°C, pressure 63 Pa) to 1305 minutes (variant with temperatures −20: 10: 20: 30°C, pressure 63 Pa). For this reason, the most favourable experimental parameters were: temperature of 30°C and pressure of 63 Pa. However, application of these parameters caused higher absorption of water vapour during storage. Therefore, the selection of freeze-drying parameters should also be related to the expected properties of the final product.

The progress in markerless technologies is bringing clinicians tools to rapidly evaluate tests such as Timed Up and Go (TUG) without compromising the time of the assessment, yet it raises questions about the potential trade-off in accuracy compared to traditional marker-based systems, suggesting that the precision of these evaluations is not yet conclusively established. The OpenCap system is an easy tool to process 3D kinematics with two iPhone cameras placed in front of the subject. Previous research has primarily focused on walking and movement towards the cameras with the subject facing the cameras (WF) and thus has been unable to disentangle the differences in the movement directions. We have compared the OpenCap system with a standard marker-based system for both walking directions. In OpenCap, we found significantly worse results capturing walking facing away from the cameras (RW). Compared to the marker-based system, our findings indicate troubles measuring kinematic parameters but provide good accuracy in measuring spatial-temporal parameters. These insights pave the way for refining markerless assessment technologies, potentially enhancing their utility in clinical settings.

Quantitative analysis of human gait is critical for early discovery, progressive tracking, and rehabilitation of neurological and musculoskeletal disorders, such as Parkinson’s Disease, stroke, and Cerebral Palsy. Gait analysis typically involves estimating gait characteristics, such as spatio-temporal gait parameters and gait health indicators (e.g., step time, length, symmetry, and balance). Traditional methods of gait analysis involve the use of cameras, wearables, and force plates, but are limited in operational requirements when applied in daily life - such as direct line-of-sight, carrying devices, and dense deployment. This paper introduces a novel approach for gait analysis by passively sensing footstep-induced floor vibrations during walking using vibration sensors mounted on the floor surface. Our approach is non-intrusive, scalable, and perceived as more privacy-friendly, making it suitable for continuous gait health monitoring in daily life. We developed a floor vibration-based gait analysis framework to estimate various gait parameters that are used as standard metrics in medical practices, including temporal parameters (step, stride, stance, swing, double-support, single-support time) and spatial parameters (step length, width, angle, stride length), and extracts gait health indicators (cadence/walking speed, left-right symmetry, gait balance, initial contact types). The main challenge is that floor vibrations are distinct across different floor types. To address this challenge, our approach develops floor-adaptive algorithms to extract floor-specific features and is designed to be generalizable to various settings, including homes, hospitals, and eldercare facilities. We evaluate our approach through real-world walking experiments with 20 adults with 12,231 labeled gait cycles across concrete and wooden floors. Our results show 90.5% (RMSE 0.08s), 71.3% (RMSE 0.38m), and 92.3% (RMSPE 7.7%) accuracy in estimating temporal, spatial parameters, and gait health indicators, respectively.

This review delves into the growing field of flexible and stretchable strain sensors utilized in human gait analysis, focusing on determining knee bending angle and muscle activities when a human subject walks. Recent advancements have enabled these sensors to accurately capture biomechanical parameters while accommodating the body's natural movements. We examine the principles underlying these sensors' design and fabrication techniques, emphasizing their flexibility, stretchability, and biocompatibility for seamless integration into wearable systems. Through critical evaluation of existing methodologies, we assess the reliability and validity of these sensors in quantifying gait parameters. Furthermore, we discuss this technology's clinical and research implications, highlighting its potential in personalized rehabilitation and sports performance optimization. We provide an overview of flexible strain sensors and their application for analyzing human walking gait, especially for observing walking gait in rehabilitation programs. First, we present the basic working principles of various flexible strain sensors. Second, by the application of flexible strain sensors as walking gait monitoring. Finally, current challenges and future opportunities in this research area are discussed. By synthesizing current knowledge and outlining future directions, this review aims to provide insights for researchers and practitioners seeking to leverage flexible and stretchable strain sensors for comprehensive human gait analysis.

Freeze drying (FD) is a technique used to preserve the bioactive content and flavor of samples. Foods with a short shelf life due to nature have been preserved by FD in recent years. The success of the drying technique is thanks to the high retention ability of the bioactive compounds and the flavor of the sample. However, the high cost and energy consumption of the FD limit its usage in several fields. Freezing, primary drying, and secondary drying, which take place in the same device, are the stages of the FD. In addition, several parameters, including pretreatment, size, temperature, sample species, time, and pressure, affect the FD process. These parameters are controlled to increase the effectiveness of the FD on the samples. Moreover, FD was compared with other drying techniques including hot-air drying, microwave drying, vacuum drying, and solar drying to determine its protective capability. It has also been applied to the valorization of waste products, which is a common problem worldwide. For valorization, microencapsulation and powder production have been achieved by FD. In recent years, studies on the effects and use of the FD on various materials increased, providing new aspects for the future of science and food industry.

The rock joint fissure slope in cold regions is prone to deformation and failure problems such as relaxation, tension and collapse under freeze-thaw (F-T) cycles. Based on the ideology of clean production and promoting the structural integrity of geotechnical projects in cold areas, this study designed and prepared aeolian-sand (AS) to replace part of river sand as a filling mortar material by taking advantage of the low cost and easy availability of AS. Investigations were carried out to determine the impact of varying proportions of AS in mortar on the microstructure and shear properties of the mortar-rock interface under F-T cycles. Therefore, F-T cycle testing, nuclear magnetic resonance (NMR) testing and shear testing were carried out on grout with different proportions of AS. The results show that the right proportion of AS replacement could enhance the shear deformation resistance and F-T resistance of the mortar-rock interface, and 30% proportion is the optimal proportion. By increasing of F-T cycles, the three types of specimens showed different degrees of particle spalling, shedding and cracking. The slurry-rock interface layer in the A (0%) group exhibited the most severe F-T deterioration, while the B (15%) group showed a lesser degree, and the C (30%) group performed the best. T2 spectrum curve and total spectrum area change law from the microscopic point of view to verify the 30% AS proportion mortar-rock interface F-T resistance is the strongest, followed by 15% AS proportion mortar, the weakest is ordinary mortar. The degradation of the mortar-rock bond is primarily due to the conversion of solid to liquid phases and the movement of internal water caused by fluctuating temperatures. The extent of F-T deterioration in the slurry-rock interface layer is greatly affected by the varying proportions of AS. The shear strength and shear stiffness of specific proportion of AS decreased with the increase of F-T cycles. For same F-T cycles, the shear strength and shear stiffness of group C (30%) were the highest, followed by group B (15%) and group A (0%). The grout material not only reinforces the F-T joint fissure slope, but also reduces the cost of grout reinforcement and promotes the clean production of geotechnical structures.

Techniques have been developed to determine whether a horse is in resting or running mode by measuring at least one of the following: the horse's body temperature, heart rate, oxygen saturation, and exercise level. However, the existing technology has not reached a level where a trainer can accurately assess a horse's running conditions, such as speed, acceleration, stride, limb rotation, ground impact, and frontal balance, during the training of racehorses. In addition, data is needed to quickly detect abnormalities during training and provide a basis for changing the intensity of training or deciding to give a rest to the horse. Devices that detect abnormalities in equine gait with high sensitivity will contribute to animal welfare and increase the athletic longevity of horses. This paper reports the development results of a new IoT device that acquires, processes, and analyzes information such as heart rate, position, speed, acceleration, pitch, stride, and ground contact during a training of racehorses. The purpose of this development is to provide an information on a novel processing system, device, method, and program that can analyze training condition of racehorses from multiple angles.

Freezing of Gait (FoG) is a disabling motor complication in Parkinson’s disease (PD), affecting approximately 50% of advanced PD patients. It is characterized by sudden and transient inability to initiate or maintain walking, leading to falls and reduced quality of life. This study investigates the relationship between white matter integrity and step initiation impairments in FoG. Forty-three PD patients (26 with FoG) underwent diffusion-weighted imaging to assess white matter DTI metrics and kinematic analysis during step initiation tasks. Multiple regression analyses were conducted to explore the connection between white matter tract integrity and step initiation behavior. The multiple regression analysis shows that (1) Right Inferior Longitudinal Fasciculus RD explained 31% of APA duration’s variance; (2) Corpus Callosum Forceps Major explained 25% of the step length's variance. There was a positive correlation between the Right Inferior Longitudinal Fasciculus RD and APA duration and a negative correlation between Corpus Callosum Forceps Major RD and step length. The findings suggest that compromised white matter integrity in RILF and CC contributes to impaired motor control during step initiation in FoG. These regions are critical for inhibitory control and interhemispheric coordination, crucial for APA execution and step length regulation.

The objective of this study is to investigate the aquatic-toxic effects of glyoxal-containing cellulose ether with four different glyoxal concentrations (0, 1.4, 2.3 and 6.3%) in response to global chemical regulations, e.g., European Union Classification, Labeling and Packaging (EU CLP). Tests of the aquatic-toxic effects of glyoxal-containing cellulose ether on 11 freeze-dried microbial strains, Microcystis aeruginosa, Daphnia magna and zebrafish embryos were designed as an initial stage for toxicity screening, and were performed with the standardized toxicity test guidelines. Glyoxal-containing cellulose ether showed no significant toxic effects in the toxicity tests for the 11 freeze-dried microbial strains, Daphnia magna and zebrafish embryos. Alternatively, 6.3% glyoxal-containing cellulose ether led to more than a 60% reduction of Microcystis aeruginosa growth after 7 days of exposure. Approximately 10% developmental abnormalities (e.g., bent spine) in zebrafish embryos were also observed in the group exposed to 6.3% glyoxal-containing cellulose ether after 6 days of exposure. These results imply that <6.3% glyoxal-containing cellulose ether results in non-toxic effects on the acute toxicity of aquatic organisms. However, ≥6.3% glyoxal-containing cellulose ether may affect the health of aquatic organisms with long-term exposure. In order to better evaluate the eco-safety of cellulosic products contained in glyoxal, further studies regarding the toxic effects of glyoxal-containing cellulose ether with long-term exposure are required. The results from this study allow us to evaluate the auatic-toxic effects of glyoxal-containing cellulosic products, under EU chemical regulations, on the health of aquatic organisms.

State-of-the-art augmented-reality (AR) glasses record their position and orientation in space, enabling measurements and analyses of clinical gait-and-balance tests. This study’s objective was to evaluate concurrent validity and test-retest reliability for common clinical gait-and-balance tests in people with Parkinson’s disease: the Five Times Sit-To-Stand (FTSTS) and Timed Up-and-Go (TUG) tests. Position and orientation data was collected in 22 participants with Parkinson's disease using HoloLens 2 and Magic Leap 2 AR glasses, from which test-completion durations and durations of distinct sub-parts (e.g., sit-to-stand, turning) were derived and compared to reference systems and over test repetitions. Regarding concurrent validity, for both tests an excellent between-systems agreement was found for position and orientation time series and test-completion durations. Between-systems agreement for FTSTS (sub-)durations were all excellent, while TUG turning sub-durations were excellent (turn 1) and moderate (turn 2). Regarding test-retest reliability, the within-system test-retest variation in test-completion times and sub-durations was always much greater than the between-systems variation, implying that these (sub-)durations may be derived interchangeably from AR and reference-system data. In conclusion, AR data are of sufficient quality to evaluate gait and balance in people with Parkinson's disease, with valid quantification of test-completion durations and sub-durations of distinct FTSTS and TUG sub-parts.

Digital gait monitoring is increasingly used to assess locomotion and fall risk. The aim of this work is analyzing the changes in the foot-floor contact sequences of Parkinson’s Disease (PD) patients in the year following the implant for deep brain stimulation (DBS). During their best-ON condition, 30 PD patients underwent gait analysis at baseline (T0), at 3 months (T1), and 12 months (T2) after the DBS neurosurgery for bilateral high-frequency subthalamic nucleus stimulation. Thirty age-matched controls underwent gait analysis once. Each subject was equipped with bilateral foot-switches and a 5-minute walk was recorded, including both straight-line and turnings. The walking speed, turning time, stride time variability, percentage of atypical gait cycles, stance, swing, and double support duration were estimated. Overall, the gait performance of PD patients improved after DBS, as also confirmed by the decrease in the UPDRS-III score from 19.4±1.8 to 10.2±1.0 points (T0 vs. T2) (p < 0.001). In particular, the percentage change of atypical gait cycles of PD more affected side decreased at T1 (Straigh-line: -72%; Turnings: -43%) and at T2 (Straigh-line: -54%; Turnings: -20%). The percentage of atypical gait cycles proved an informative digital biomarker for quantifying PD gait changes after DBS, both in straight-line paths and turnings.

Total hip arthroplasty (THA) is a preferred treatment for primary osteoarthritis (OA) or secondary due to developmental hip dysplasia (DDH). Gait analysis is considered a golden standard for evaluating post-arthroplasty walking patterns. This study compared post-THA spatiotemporal gait parameters (SGPs) between OA and DDH patients and explored correlations with demographic and clinical variables. Thirty patients (15 per group) were recorded during gait, and their SGPs were analyzed. Functionality was evaluated with the Oxford Hip Score (OHS). The OA patients were significantly older than DDH (pr< 0.51, all p< 0.05). The preoperative gait alterations associated with OA or DDH were improved to similar levels in both groups after THA. Post-arthroplasty SGPs and OHS correlations indicate limitations in certain activities. These find-ings must be correlated with kinetic gait analysis data to fully evaluate gait and functionality dif-ferences among patient groups.

This study investigates the collapse of the medial longitudinal arch (MLA) as a risk factor for medial tibial stress syndrome (MTSS), hypothesizing that overuse of extrinsic foot muscles to prevent MLA collapse can lead to disability. Twenty healthy adults (39 feet) with a foot posture index score below 6 and no recent lower extremity orthopedic history participated. Ultrasonog-raphy measured foot muscle cross-sectional areas, while three-dimensional motion analysis us-ing VICON assessed foot kinematics during gait, focusing on navicular height at initial contact (ICNH) and dynamic navicular drop (DND) during the stance phase. Hierarchical cluster analy-sis based on ICNH and DND compared muscle cross-sectional areas between clusters using ANOVA or Kruskal–Wallis test. The analysis indicated that ICNH was lower in clusters 1 and 3 than in cluster 2, and DND was smaller in clusters 1 and 2 than in cluster 3. Although there was no significant difference in muscle cross-sectional area between the clusters, the flexor hallucis longus tended to be thicker in cluster 1 than in cluster 3 (p = 0.051). The findings suggest that the flexor hallucis longus may help prevent MLA compression during loading, indicating that over-use of extrinsic foot muscles may contribute to MTSS development.

Introduction: Low back pain (LBP) is the leading cause of lost productivity, absenteeism, disability, and early retirement worldwide. LBP treatment should be comprehensive, including prevention, education, diagnosis, and various treatment methods. Treatment can be divided into pharmacological and non-pharmacological. The role of physiotherapy in the comprehensive treatment of LBP is very important. Elastic therapeutic tape, also called kinesiology tape or therapeutic kinesiology tape, has been used for about 50 years. Purpose: The aim of this study was to evaluate the effectiveness of Kinesio taping in patients suffering from (LBP) and its possible effect on the swing of the center of pressure (COP), balance, gait, improvement of coordination, and pain reduction. Material and methods: A total of 60 patients aged 20 to 83 years (54% women) were examined, all of whom met the inclusion and exclusion criteria. In the experimental group, in addition to comprehensive rehabilitation, kinesiotaping of the L1-L5 spine was used. The control group underwent balance control training. The research tools used included the Bohannon single-leg standing test, the FAC scale - Functional Ambulatory Category, the Podsiadlo and Richardson Standing and Walking Test - Timed Up and Go (TUG), lumbar spine mobility assessment, Lasegue's sign and examination of neurological deficit symptoms. and self-assessment of pain using the Visual Analogue Scale (VAS). Results: Kinesio taping has a statistically significant effect on postural control, balance, gait, coordination, and pain. The main parameter with a statistically significant effect on the effects of Kinesio taping was age (below 55 years), which was also observed in the control group. Conclusions: Kinesio taping is an effective method in the treatment of LBP. It improves postural control, balance, gait, coordination, and pain.

Veterinary science has benefitted from technological advancements in the past and will hopefully continue to do so, especially in the field of equine gait analysis. There is a need for rapid and easy to use technology that is accurate and portable, but at the same time is also readily interpretable. This manuscript presents two new approaches to equine gait analysis, both of which are commer-cial devices. The use of Acoustic MyoGraphy (AMG) has been proven in the field of muscle func-tion and performance as well as ligament health, but it can also provide details concerning gait when placed on the wall of the hoof of a horse. The TendibootTM system is a limb focused unit that can be easily attached, activated and used in a Veterinary clinic setting, rapidly providing gait details for equine diagnostic purposes. In conclusion this manuscript provides an insight into gait parameters from recent research trials that are novel and challenge current thinking.

Porous β-tricalcium phosphate (Ca3(PO4)2; β-TCP) was prepared by freeze-drying and the effects of this process on pore shapes and sizes were investigated. Various samples were prepared by freezing β-TCP slurries above a liquid nitrogen surface at −180 °C with subsequent immersion in liquid nitrogen at −196 °C. These materials were then dried under reduced pressure in a freeze-dryer after which they were sintered by heating. Compared with conventional heat-based drying, the resulting pores were more spherical, which increased both the mechanical strength and porosity of the β-TCP. These materials had a wide range of pore sizes from 50 to 200 µm, with the mean and median values both approximately 100 µm regardless of the freeze-drying conditions. Mercury porosimetry data showed that the samples contained small, interconnected pores with sizes of up to 1.24 µm and macroscopic, interconnected pores up to 25.8 µm in size. The effects of non-ionic surfactants having different hydrophilic/lipophilic balance (HLB) values on foaming and pore size were also investigated. Materials made with surfactants having lower HLB values exhibited smaller pores and lower porosity whereas higher HLB surfactants gave higher porosity and slightly larger macropores. Even so, the pore diameter could not be readily controlled solely by adjusting the HLB value. The findings of this work indicated that high porosity (75%) and good compressive strength (&gt;2 MPa) can both be obtained in the same porous material and that foaming agents with HLB values between 12.0 and 13.5 were optimal.

Ankle sprains are the most frequently occurring musculoskeletal injuries among recreational athletes. Ankle support through bandages following the initial orthotic treatment might be beneficial for rehabilitation purposes. Since hardly any study has investigated the impact of bandages in the acute phase of ankle sprains, our study examined the immediate effects of wearing an ankle bandage on fine coordination, proprioception, and motor performance in subjects five weeks after an acute ankle injury. In total, 70 subjects with acute unilateral supination trauma were tested. All subjects completed several rating questionnaires and biomechanical investigations, including a fine coordination and proprioception test, single leg stances, the Y-Balance test and gait analysis. All biomechanical investigations were conducted for the subject's injured leg with and without a bandage (MalleoTrain® Bauerfeind AG) and the healthy leg. Subjects reported moderate to strong improvements in ankle stability and pain when wearing the bandage. Wearing the bandage significantly normalized subjects’ single leg stance performance, as well as the stance phase duration, and the vertical ground reaction forces during walking. However, the bandage did not have a clear effect on fine coordination and proprioception. Wearing a bandage in the acute phase of an ankle sprain may immediately improve motor performance, including standing and walking.

Mobile health technologies enable continuous, quantitative assessment of mobility and gait in real-world environments, facilitating early diagnosis of gait disorders, disease progression monitoring, and prediction of adverse events like falls. Traditionally, mobile gait assessment predominantly relied on body-fixed sensors positioned at the feet or lower trunk. Here, we investigate the potential of an algorithm utilizing an ear-worn motion sensor for spatiotemporal segmentation of gait patterns. We collected 3D acceleration profiles from the ear-worn sensor during varied walking speeds in 53 healthy adults. Temporal convolutional networks were trained to detect stepping sequences and predict spatial relations between steps. The resulting algorithm, mEar, accurately detects initial and final ground contacts (F1 score of 99% and 91%, respectively). It enables determination of temporal and spatial gait cycle characteristics (among others stride time and stride length) with good to excellent validity at a precision sufficient to monitor clinically relevant changes in walking speed, stride-to-stride variability, and side asymmetry. This study highlights the ear as a viable site for monitoring gait and proposes its potential integration with in-ear vital sign monitoring. Such integration offers a practical approach to comprehensive health monitoring and telemedical applications, by integrating multiple sensors in a single anatomical location.

Keywords: grape pomace extracts, encapsulation, freeze-drying, bioaccessibility, phenolic compounds

The ongoing COVID-19 pandemic has raised numerous questions concerning the shape and range of state interventions whose goals are to reduce the number of infections and deaths. The lockdowns, which have become the most popular response worldwide, are assessed as being an outdated and economically inefficient way to fight the disease. However, in the absence of efficient cures and vaccines, there is a lack of viable alternatives. In this paper we assess the economic consequences of the epidemic prevention and control schemes that were introduced in order to respond to the COVID-19 pandemic. The analyses report the results of epidemic simulations that were obtained using the agent-based modelling methods under the different response schemes and their use in order to provide conditional forecasts of the standard economic variables. The forecasts were obtained using the DSGE model with the labour market component.

An analysis of the current state of development in the agro-industrial complex (AIC) has established that freeze-drying is the most effective method for processing raw materials entering the drying stage. However, this drying method is hindered by the lack of modern, high-performance, energy-efficient drying technologies and equipment. The production of freeze-dried agricultural products will stimulate the development of AIC sectors. The implementation scheme of an automatic control system for a vacuum freeze-drying unit is considered, representing a promising and environmentally friendly direction in the processing of agricultural products. The drying equipment includes the following components and systems: a drying chamber, a cooling system, a vacuum pump, a control system, and a heating system. The product is placed on shelves in the drying chamber and frozen to a temperature that ensures the removal of 75-80% of the moisture contained in the product. The vacuum pump creates a pressure of 10-30 Pa and evacuates the spent air from the sublimator. Water vapor condensation occurs in the desublimator, and at the final stage of the drying process, the heating elements are activated to remove the remaining moisture. To validate the reliability of controlling the operating modes of the sublimator, experimental studies were conducted on the temperature dependence of the product on the surface and in the center over time. The graphs show temperature changes on the surface and in the center of the product throughout the drying process. The research results indicate that at a pressure of 20±5 Pa, the desublimator temperature should be below -20°C. The surface temperature of the product during the sublimation stage should be within the range of -25±5°C. Drying is completed when the chamber temperature reaches no more than 40°C, and the surface temperature of the product is around 30°C.

Climate change is affecting the production of temperate fruit crops. Freeze damage, particularly in spring, has resulted in significant economic losses in peach production in the southeastern United States. Research efforts in peach and other Prunus species have primarily focused on dormancy-related traits associated with bloom time, such as chill and heat requirement, with fruitlet freeze tolerance not equally represented. This study reports fruitlet freeze tolerance in 75 peach and nectarine accessions at six freezing temperatures (0 to -10ºC) using electrolyte leakage method over two seasons (2022-2023). Fruitlet freeze tolerance ranged from -3.94 to -10.22 °C with an estimated damage ranging from 16-48% with the majority of the accessions showing tolerance to cold temperatures in the -4 to -6ºC and 25-35% range. Variability in tolerance was noted across years, including some inconsistencies between tolerance group assignments. Grouping based on the estimated damage showed better stability and some accessions changed their grouping from the extremes to an intermediate tolerance group. Interestingly, nectarine accessions were among most tolerant in both seasons. Broad-sense heritability of 0.52 and 0.85, for freeze tolerance and estimated damage, respectively, suggested genetic control of this trait with a potential for improvement via breeding.

Background: The prevalence of falls among the older population underscores the imperative of comprehending human adaptations to gait perturbations. Dual-belt treadmills offer a controlled setting for such investigations. The purpose of this study was to examine the effect of acceleration of one belt of the treadmill during three different phases of the gait cycle on kinematic and kinetic parameters and relate these changes to unperturbed gait. Methods: Twenty-one healthy young females walked on a treadmill in a virtual environment, in which five unexpected perturbations were applied to the left belt at the Initial Contact (IC), Mid Stance (MS), and Pre-Swing (PS) phase of the gait cycle. Data from the undisturbed gait and the first disturbance of each trial were extracted for analysis. Results: All perturbations significantly affected the gait pattern, mainly by decreasing the knee extension angle. The perturbation in the IC phase had the most significant effect, resulting in a 248.48% increase in knee flexion torque. The perturbation in the MS phase mainly affected plantar flexion torque, increasing it by 118.18%, while perturbation in the PS phase primarily increased the hip extension torque by 73.02%. Conclusions: The presence of perturbations in the IC and PC phases caused the most aggressive and significant changes in gait parameters.

Natural phytochemicals in foods, including anthocyanins, can play an important role in human health. Anthocyanins have been reported to cause many various useful effects, such as reducing cancer cell proliferation, regulating blood pressure, preventing tumour formation, improving eyesight, and preventing diabetes. In this study, we aimed to reveal the qualitative anthocyanin content, antiproliferative and antimicrobial effects of different extracts derived from Vaccinium myrtillus, V. corymbosum, Sambucus nigra and Aronia melanocarpa. The anthocyanin content of the plants mentioned in the study was characterized after the freeze-drying process. MTT assay was used to determine the antiproliferative effect of extracts on cancer cells. Antimicrobial effects of extracts were studied on typical and clinical strains of 5 different bacteria. As a result, the anthocyanin content in the extracts obtained was determined to be quite good with the freeze-drying method, and it was also determined that the extracts had various levels of antiproliferative and antibacterial effects.

Immersive virtual reality has the potential to motivate and challenge patients that need and want to relearn movements in the process of (neuro-)rehabilitation. The aims of this study were to evaluate the feasibility and users’ acceptance of an innovative immersive virtual reality system (head-mounted display) used in combination with robot assisted gait training in subjects suffering from neurological diseases. Fifteen participants tested a single session of immersive virtual reality by means of head-mounted display during a Lokomat gait session. Training parameters and safety indicators were collected and the acceptance was investigated among the participants and the therapists. The results suggest that the immersive virtual reality system is feasible with respect to safety and tolerance. Furthermore, the very positive overall acceptance of the system suggests that it has potential to be included in a robot assisted gait training session by means of Lokomat. Taken together, this study demonstrates the feasibility and acceptance of an innovative immersive virtual reality system in combination with a robot assisted gait training in subjects suffering from stroke and spinal cord injury, as well as their therapists.

Findings on diet-health relationships have led many people to include healthier food items (including snacks) in their diets, e.g. those containing probiotic microorganisms. The purpose of this study was to compare two methods to produce probiotic freeze-dried banana slices - one of them consisting of impregnating slices with a suspension of probiotic Bacillus coagulans, the other based on coating the slices with a starch dispersion containing the bacteria. Both processes have resulted in viable cell counts above 7 log ufc.g-1, although the presence of the starch coating has avoided a significant loss of viability on freeze-drying. The coated slices were less crispy than the impregnated ones, according to the shear force test results. However, the sensory panel (with more than 100 panelists) have not perceived significantly texture differences. Both methods have presented good results, in terms of probiotic cell viability and sensory acceptability (the coated slices having been significantly more accepted than the non-probiotic control slices).

Background : The quantification of electromyographic activity using surface electrodes is inval-uable for understanding gait disorders in patients with central nervous system lesions. We propose to evaluate a commercially available low-cost system compared to a reference system in partic-ipants with stroke-related movement disorders in functional situations. Methods : Three hemiparetic participants performed three functional tasks: two treadmill walks at different speeds and a sit-to-stand test. The vastus lateralis and gastrocnemius medialis muscles were equipped with two EMG sensors. The comparison between the two EMG systems was based on 883 identified cycles. Spearman’s correlation coefficients (SC), linear correlation coefficients (LCC), and cross-correlation coefficients (CCC) were calculated. Results : The main results indicate good to very good similarity of the EMG signals collected from the two tested sEMG systems. In the comfortable walking condition, an SC of 0.894±0.091 and an LCC of 0.909±0.094 were noted. In the fast walking condition, an SC of 0.918±0.064 and an LCC of 0.935±0.056 were observed. For the 1-minute sit-to-stand test an SC of 0.880±0.058 and an LCC of 0.881±0.065 were noted. Conclusions : This study demonstrates good to very good similarity between the two sEMG systems, enabling the analysis of muscle activity during functional tasks.

Freezing of gait (FOG), a debilitating symptom of Parkinson’s disease (PD), can be safely studied using the stepping in place (SIP) task. However, clinical, visual identification of FOG during SIP is subjective and time consuming, and automatic FOG detection during SIP currently requires measuring center of pressure on dual force plates. This study examines whether FOG elicited during SIP in 10 individuals with PD could be reliably detected using kinematic data measured from wearable inertial measurement unit sensors (IMUs). A general, logistic regression model (AUC = 0.81) determined that three gait parameters together were overall the most robust predictors of FOG during SIP: arrhythmicity, swing time coefficient of variation, and swing angular range. Participant-specific models revealed varying sets of gait parameters that best predicted FOG for each participant, highlighting variable FOG behaviors, and demonstrated equal or better performance for 6 out of the 10 participants, suggesting the opportunity for model personalization. The results of this study demonstrated that gait parameters measured from wearable IMUs reliably detected FOG during SIP, and the general and participant-specific gait parameters allude to variable FOG behaviors that could inform more personalized approaches for treatment of FOG and gait impairment in PD.

Background: This study aimed to investigate how external perturbations caused by the treadmill belt's acceleration (Acc) and deceleration (Dec) during the Initial Contact (Initial), Mid Stance (Mid) and Pre-Swing (ToeOff) phase affect gait regularity in young adults. Methods: Twenty-one healthy young females walked on a treadmill in a virtual environment (Grail, Motek), where four unexpected perturbations were applied to the left belt at Initial, Mid, and ToeOff. Sample Entropy (SampEn) was calculated for the center of mass (CoM) displacements, for six perturbation scenarios in three directions: anterior-posterior (AP), medial-lateral (ML), and vertical (vert), with SampEn vector lengths (m) ranging from 2 to 10. Results: The CoM displacement exhibited its highest regularity (low SampEn values) in the AP and vert-directions during Dec_ToeOff, across all m values. Similarly, this pattern was observed in the ML-direction, but exclusively for m = 2 and 4. The least regular CoM trajectories (high SampEn values) were for Dec_Mid in the AP-direction, across all m values. This trend persisted in the ML-direction, only for m = 2 and 4. However, the most irregular CoM displacements in the ML-direction occurred during Dec_ToeOff for the remaining m values. Vertical CoM displacements exhibited the highest irregularities during Dec_Initial for m ≥ 4. Conclusions: Evaluating the regularity of CoM displacements using SampEn can be a useful tool for assessing how gait perturbations are handled.

The paper presents an innovative hexapod walking robot built with 3-UPU parallel mechanism. In the robot, the parallel mechanism is used as both an actuator to generate walking and also a connecting body to connect two groups of three legs, thus enables the robot to walk with simple gait by very few motors. In the paper, the forward and inverse kinematics solutions are obtained. The workspace of the parallel mechanism is analyzed using limit boundary search method. The walking stability of the robot is analyzed, which yields the robot’s maximum step length. The gait planning of the hexapod walking robot is studied for walking on both flat and uneven terrains. The new robot, combining the advantages of parallel robot and walking robot, has a large carrying capacity, strong passing ability, flexible turning ability, and simple gait control for its deployment for uneven terrain.

Sleep quality is known to affect automatic and executive brain functions such as gait control and cognitive processing. This study aimed to assess the effect of dual tasks on gait spatiotemporal parameters among young adults with good and poor sleep quality in the United Arab Emirates. In total, 65 young adults with a mean age of 21.1±2.5 were assessed for gait analysis during single-task and dual-task conditions. The participants’ sleep quality was assessed using the Pittsburgh Sleep Quality Index (PSQI), and gait was assessed using the BTS Gaitlab System. The participants were asked to walk at natural speed as a single-task condition, followed by walking while performing a cognitive task as a dual-task condition. The parameters assessed included the gait velocity (m/s), cadence (steps/min), step width (m), and stride length (m). The DTC on each gait parameter was calculated. The Mann–Whitney U test was used to compare the differences in the DTC on gait variables between the good and poor sleep quality groups, and the Spearman correlation test was used to assess the correlation between total PSQI scores and the DTC. At a significance level of p&lt;0.05, a significant difference in cadence between the two sleep quality groups was observed, in addition to a positive correlation between sleep quality and the DTC effect on gait mean velocity, cadence, and stride length. Our findings also revealed a greater DTC on participants with poorer sleep quality. These findings contribute to our understanding of the significance of sleep quality in gait performance while multitasking in younger populations.

This study aimed to identify whether the combined use of functional electrical stimulation (FES) reduces the motor torque of a gait exercise rehabilitation robot in spinal cord injury (SCI) and to verify the effectiveness of the developed automatic assist level adjustment in people with paraplegia. Acute and chronic SCI patients (1 case each) performed 10 min of gait exercises with and without FES using a rehabilitation robot. Reinforcement learning was used to adjust the assist level automatically. The maximum torque values and assist levels for each of the ten walking cycles when walking became steady were averaged and compared with and without FES. The motor's output torque and the assist level were measured as outcomes. The assist level adjustment allowed both the motor torque and assist level to decrease gradually to a steady state. The motor torque and the assist levels were significantly lower with the FES than without the FES under steady conditions in both cases. No adverse events were reported. The combined use of FES attenuated the motor torque of a gait exercise rehabilitation robot for SCI. Automatic assistive level adjustment is also useful for spinal cord injuries.

Background: Three-dimensional gait analysis plays a crucial role in the rehabilitation assessment of post-stroke hemiplegic patients. However, the data generated from such analysis is often complex and difficult to interpret in clinical practice, requiring extensive time and complicated procedures. The Gait Deviation Index (GDI) serves as a simplified metric for quantifying the severity of pathological gait. Although isokinetic dynamometry is widely employed in muscle function assessment and rehabilitation, its application in gait analysis remains underexplored. Objective: This study aims to investigate the use of isokinetic muscle strength data obtained from the Biodex system, combined with machine learning techniques, to predict the GDI in hemiplegic patients. Methods: A cohort of 150 post-stroke hemiplegic patients was evaluated. The peak torque, peak torque/body weight, maximum work of repeated actions, coefficient of variation, average power, total work, acceleration time, deceleration time, range of motion, and average peak torque for both flexor and extensor muscles on the affected side were measured at three angular velocities (60°/s, 90°/s, and 120°/s) using the Biodex System 4 Pro. GDI was calculated using data from a Vicon three-dimensional motion capture system. The study employed four machine learning models—Lasso regression, random forest (RF), support vector regression (SVR), and BP neural networks—to model and validate the data. Model performance was evaluated using mean squared error (MSE), the coefficient of determination (R²), and mean absolute error (MAE). SHapley Additive exPlanations (SHAP) analysis was used to enhance model interpretability. Results: The RF model outperformed others in predicting GDI, with an MSE of 16.18, an R² of 0.89, and an MAE of 2.99. In contrast, the Lasso regression model yielded an MSE of 22.29, an R² of 0.85, and an MAE of 3.71. The SVR model had an MSE of 31.58, an R² of 0.82, and an MAE of 7.68, while the BP neural network exhibited the poorest performance with an MSE of 50.38, an R² of 0.79, and an MAE of 9.59. SHAP analysis identified the maximum work of repeated actions of the extensor muscles at 60°/s and 120°/s as the most critical features for predicting GDI, underscoring the importance of muscle strength metrics at varying speeds in rehabilitation assessments. Conclusion: This study highlights the potential of machine learning techniques in analyzing complex clinical data. The developed GDI prediction model, based on isokinetic dynamometry data, offers a novel, streamlined, and effective tool for assessing rehabilitation progress in post-stroke hemiplegic patients, with promising implications for broader clinical application.

Traditionally, studies on freeze–thaw erosion have used the analytic hierarchy process (AHP) to calculate the weight of evaluation factors, however, this method cannot accurately depict the fuzziness and randomness of the problem. To overcome this disadvantage, the present study has proposed an improved AHP method based on the cloud model to evaluate the impact factors in freeze–thaw erosion. To establish an improved evaluation method for freeze–thaw erosion in Tibet, the following six factors were selected: annual temperature range, average annual precipitation, slope, aspect, vegetation coverage, and topographic relief. The traditional AHP and the cloud model were combined to determine the weight of the impact factors, and a consistency check was performed. The comprehensive evaluation index model was used to evaluate the intensity of freeze–thaw erosion in Tibet. The results show that freeze–thaw erosion is extensive, stretching over approximately 66.1% of Tibet. The problem is the most serious in Ngari Prefecture and Nagqu. However, mild erosion and moderate erosion, accounting for 37.1% and 25.0%, respectively, of the total freeze–thaw erosion are the most widely distributed. The evaluation results for the freeze–thaw erosion was confirmed to be consistent with the actual situation. In brief, this study provided a new approach to evaluate the conditions of freeze–thaw erosion quantitively in Tibet.

Gait variability (GV) is a crucial measure of inconsistency of muscular activities or body seg-mental movements during repeated tasks. Hence, GV might serve as a relevant and sensitive measure to quantify adjustments of walking control. However, has not been clarified whether GV is associated with walking speed to exploit effective better coordination level. Fourteen male stu-dents (age 22.4 ± 2.7 years, body mass 74.9 ± 6.8 kg, body height 1.78 ± 0.05 m) took part in this study. After three days of walking 1 km each day at a self-selected speed (SS) on asphalt with Apple Watch S. 7 (AppleTM), the participants were randomly evaluated on a treadmill at three different walking speed intensities for 10 minutes each one, at SS-20% / SS+20% of SS, with 5 minutes of passive recovery in-between. Heart rate (HR) was monitored beat-to beat and nor-malized as HR%MAX, while the rate of perceived exertion (RPE) (CR-10) was asked after each trial. Kinematic analysis was performed assessing the Contact Time (CT), Swing Time (ST), Stride Length (SL), Stride Cycle (SC) and Gait Variability as Phase Coordination Index (PCI). RPE and HR increased with higher walking speed (P = 0.005 and P = 0.035, respectively). CT and SC decreased as the speed increased (P = 0.0001 and P = 0.013, respectively), while ST remained un-changed (P = 0.277). SL increased with higher walking speed (P = 0.0001). Conversely, PCI was 3.81 ± 0.88 % (high variability) at 3.96 ± 0.47 km·h-1, 2.64 ± 0.75 % (low variability) at SS (4.94 ± 0.58 km·h-1), 3.36 ± 1.09 % (high variability) at 5.94 ± 0.70 km·h-1 (P = 0.001). These results indi-cate that while the metabolic demand and kinematics variables changing linearly with increasing speed, the most effective GV was observed at SS. Therefore, SS could be a new methodological approach to choose the individual walking speed, normalize the speed intensity, and avoid a gait pattern alteration.

Geopolymer concrete (GPC) represents an innovative green and low-carbon construction material, offering a viable alternative to ordinary Portland cement concrete in building applications. However, existing studies tend to overlook the recyclability aspect of GPC for future use. Various structural applications necessitate the use of concrete with distinct strength characteristics. The recyclability of the parent concrete is influenced by these varying strengths. This study examined the recycling potential of GPC across a spectrum of strength grades (40, 60, 80 and 100 MPa, marked as C40, C60, C80 and C100) when subjected to freeze-thaw conditions. The cementitious material comprised 60% metakaolin and 40% slag, with natural gravel serving as the coarse aggregate, and the alkali activator consisting of sodium hydroxide solution and sodium silicate solution. The strength of the GPC was modulated by altering the Na/Al ratio. After 350 freeze-thaw cycles, the GPC specimens underwent crushing, washing, and sieving to produce recycled geopolymer aggregates (RGAs). Subsequently, their physical properties and microstructure were thoroughly examined. The findings indicated that GPC with strength grades of C100, C80, and C60 were capable of enduring 350 freeze-thaw cycles, in contrast to C40, which did not withstand these conditions. RGAs derived from GPC of strength grades C100 and C80 complied with the criteria for Class II recycled aggregates, whereas RGAs produced from GPC of strength grade C60 aligned with the Class III level. A higher strength grade in the parent concrete correlated with enhanced performance characteristics in the resulting recycled aggregates.

Total ankle replacement (TAR) implants are an effective option to restore the range of motion of the ankle joint for arthritic patients. An effective tool for analyzing these implants’ mechanical performance and longevity in-silico is finite element analysis (FEA). ABAQUS FEA was used to statically analyze the von Mises stress and contact pressure on the articulating surface of the bearing component in two newly installed fixed-bearing total ankle replacement implants (the Wright Medical INBONE II and the Exactech Vantage). This ultra-high molecular weight polyethylene (UHMWPE) bearing commonly fails and is the cause for surgeon revisions. Six different FEA models for various gait percentages during stance (10%-60%) were created. They varied in magnitude of the compressive load and the ankle dorsiflexion/plantarflexion angle. The results indicated that the von Mises stress and contact pressure distributions increased as compressive load increased, and the largest magnitudes occurred at high dorsiflexion angles (15-30°). High magnitudes occurred in regions where the thickness of the bearing was the least. Additionally, high contact pressures were examined in areas near the talar component's edge or at the bearing's edges. To the author’s knowledge, this is the first study available to the research community that analyzes the Vantage implant with FEA. This study lays an essential foundation for future researchers in presenting a thorough literature review of TAR and methods for a simple FEA model setup. This study provides valuable information that can be beneficial to medical company designers and orthopedic surgeons in understanding the stress response and contact pressure of TAR implants during use.

In the seasonally frozen regions, during the grouting of prestressed bridge ducts in low-temperature environments, incompletely cured grout materials undergo volumetric changes due to the freeze-thaw cycling, resulting in structural cracks along the prestressing ducts of the bridge, thereby diminishing the bridge's operational lifespan. To investigate the frost heaving characteristics of grout materials under freeze-thaw cycles and propose potential enhancements, this study was devised to conduct frost heaving stress tests on grout materials. Through this research, we gained insights into how various additives affect the frost heaving stress characteristics of grout materials under freeze-thaw cycles. Incorporating analyses of free water content, setting time, compressive strength, as well as macroscopic examinations such as XRD and SEM, this study delves into the mechanisms for enhancing frost heaving characteristics of grout materials. Furthermore, it proposes a research approach that utilizes multiple admixtures to improve the frost heaving properties of grout materials. Through frost heaving stress tests and other macroscopic experiments, the study investigates the influence of these combined admixtures on frost heaving stress in grout materials and elucidates the underlying improvement mechanisms. The results indicate that reducing the water-cement ratio, incorporating calcium formate, sulfoaluminate cement, air-entraining agents, and carbamide all have a positive impact on mitigating frost heaving stress in grout materials. However, the improvement mechanisms differ, and employing a single measure alone is insufficient to effectively reduce frost heaving stress while meeting performance criteria such as compressive strength, setting time, and flowability. Free water content emerges as a crucial indicator determining the magnitude of frost heaving stress in grout materials, with 11.5% of free water content representing the critical threshold for frost heaving in grout materials. Utilizing composite admixtures can simultaneously decrease free water content, lower the freezing point of free water, and alleviate frost heaving deformation, resulting in more efficient reduction of frost heaving stress. When the admixture content reaches 9.9%, frost heaving stress is eliminated, and the comprehensive performance parameters including compressive strength, setting time, and flowability meet the specified requirements.

The safe and efficient mining of coal seams with low porosity, low permeability and high inhomogeneity under complex geological conditions is a major challenge, among which the permeability of coal seams is crucial for coal mine gas extraction. The development of coal seam permeability enhancement technology can help coal mines to produce safely and efficiently, and the extracted coal bed methane can be utilized as a green energy. In order to study the effect of freezing and thawing on the evolution of mechanical and permeability properties of coal, triaxial permeability tests were carried out on low-permeability coal under two kinds of surrounding pressures. At the same time, dry, saturated and freeze-thaw coal were set up for comparison, and the effects of water and freeze-thaw were separated from each other. The triaxial mechanics and percolation laws of dry, saturated and freeze-thaw coal rocks were obtained, and the mechanism of the influence of freeze-thaw on the permeability evolution law of coal was revealed. The research results can provide theoretical guidance for the gas extraction technology of low permeability coal seams with increased permeability.

In order to study the performance of a new type of cement-based grouting material under the coupling effect of freezing-thawing cycle and sulfate attack, experiments were designed and carried out. The damage mechanism of the material under the coupling effect of freezing-thawing and Na2SO4 solution was analyzed by measuring the mass change, relative dynamic elastic modulus, compressive strength loss and microstructure of the new grouting material. With increasing freeze-thaw cycles, mass loss and compres-sive strength loss of the sample in 15% Na2SO4 solution gradually increase, and the relative dynamic elastic modulus gradually decreases. During a 30-cycle freeze-thaw cycle, the mass loss rate, compressive strength loss rate, and relative dynamic elastic modulus of the sample are 4.17%, 24.59%, and 84.3%, respectively, showing good corrosion resistance and frost resistance durability. Microscopic analysis showed that SO42- caused the decomposition of C-S-H gel in the sample and the formation of Gypsum, and the widening of crack width aggravated the internal deterioration, indicating that the material deterioration rate increased under the dual-factor coupling effect.

Wood has been used in the construction, furniture, and automotive industries since ancient times. In areas where wood material is used, it is combined with various fasteners. The durability of the products produced using wooden materials depends on the performance of the fasteners. Since wood is a hydroscopic and biodegradable material, various changes occur in its structure when exposed to external weather conditions. Wood materials used especially in the field of construction and urban furniture are exposed to effects such as extreme temperatures, freezing, moisture, or drying depending on the seasons. In this study, the effect of freeze-thaw cycling (FTC) process on screw direct withdrawal resistance (SDWR) of plywood produced from beech, ozigo, and okoume species was investigated. In this context, the effects of screwing time (before or after), screw orientation (face or edge), number of cycles (0 to 7) in the FTC process and plywood type parameters on SDWR were investigated. As a result of the tests, when the mean SDWR values were examined according to the plywood type, the highest values were obtained in beech, ozigo, and okoume plywood, respectively. Considering the screwing time parameter, it was determined that there was no statistically significant difference between the mean SDWR values in other plywood types except beech plywood (p&lt;0.05). When the screw orientation parameter is examined, screwing in the face direction gave better results than screwing in the edge direction in all plywood types. There was a decrease in the mean SDWR values inversely proportional to the increase in the number of cycles in FTC-treated plywood.

Antioxidants have multiple protective roles in cells and can be used as a supplement to protect cells against cryopreservation-induced detrimental effects, including protecting sperm fertility quality. The antioxidant resveratrol (3,5,4-trihydroxy-trans-stilbene; RSV) has been shown to be a protective supplement for the cryopreservation of animal sperm, including human sperm. In this study, we assessed the effect of RSV supplementation on canine sperm cryopreservation. Semen was collected from four dogs and the effect of different concentrations of RSV (0, 100, 200, and 400 µM) on post-thaw quality of sperm was examined. After thawing, sperm motility was assessed using computer aided sperm analysis, and the structural integrity of the plasma membrane, acrosome, and chromatin were examined, as well as mitochondrial activity and gene expression were assessed. Dog sperm cryopreserved with 200 µM RSV showed significant improvement in motility and viability following thawing compared with that of the control group (p &lt; 0.05). Moreover, RSV-supplemented samples showed significantly higher numbers of sperm with an intact plasma membrane, active mitochondria, and structural integrity of acrosomes and chromatin than that of control samples (p &lt; 0.05). Furthermore, gene expression showed that RSV supplemented samples showed lower expression of pro-apoptotic (BAX) oxidative stress-related (ROMO1) and oxidative induced DNA damage repair (OGG1) whereas higher expression levels of anti‐apoptotic (BCL2) protamine-2 (PRM2), protamine-3 (PRM3) and sperm acrosome‐associated (SPACA3) genes than control. Our results suggest that RSV, at its optimum concentration, can be efficiently used as an alternative antioxidant in the cryopreservation of dog sperm.

This paper pioneers a novel exploration of environmental impacts in livestock farming, with a focus on pig farming's intersection with climate change and sustainability. It emphasizes the transformative potential of data-driven Artificial Intelligence (AI) methodologies, specifically the Internet of Things (IoT) and multimodal data analysis, in promoting equitable and sustainable food systems. The study observes five pigs, aged 86 to 108 days, using a tripartite sensor that records heart rate, respiration rate, and accelerometer data. The unique experimental design alternates between periods of isolation during feeding and subsequent pairing, enabling the investigation of stress-induced changes. Key inquiries include discerning patterns in heart rate data during isolation versus paired settings, fluctuations in respiration rates, and behavioral shifts induced by isolation or pairing. The study also explores potential detection of gait abnormalities, correlations between pigs' age and their gait or activity patterns, and the evolution of pigs' walking abilities with age. The paper scrutinizes accelerometer data to detect activity changes when pigs are paired, potentially indicating increased stress or aggression. It also examines the adaptation of pigs to alternating isolation and pairing over time, and how their heart rate, respiration rate, and activity data reflect this process. The study considers other significant variables, such as time of day and isolation duration, affecting the pigs' physiological parameters. Sensor data is further utilized to identify behavioral patterns during periods of feeding, isolation, or pairing. In conclusion, this study harnesses IoT and multimodal data analysis in a groundbreaking approach to pig welfare research. It underscores the compelling potential of technology to inform about overall pig welfare, particularly stress levels and gait quality, and the power of data-driven insights in fostering equitable, healthy, and environmentally conscious livestock production systems.

Brucellosis is a multi-system infectious disease that exhibits with various manifestations and complications. Neurobrucellosis is a rare but serious presentation of brucellosis that can be discovered in every stages of the disease. Laboratory tests and physical examination and patient history are generally the basis for diagnosing the disease. It has both insidious and prolonged clinical course of the disease and long-term therapies. Also the most common pattern of exhibition is subacute or chronic. We reported a case of young female who had history of painless weakness in the right lower limb (proximal and distal) that started gradually and had progressed over the time, and after a month she felt weakness in the left lower limb with the same pattern. Lumbosacral Magnetic resonance imaging (MRI) with and without contrast was shown evidence of enhancement thickening of caudal equina ventral roots. Brucella antigen titer was positive, the result was 1/160. And other clinical tests were normal. Patient treated with Intravenous injection (IV) Rifampicin and Intravenous Cotrimoxazole. patient was discharged with good health and continuinng all two medications for 5 months. The descision was taken to report this case as a result of entire respond in patient’s illness after a enduring disease. Neurobrucellosis is a treatable disease in which it would be better to consider a high indication of suspicion. Due to if ignored, it may cause significant morbidity and mortality.

To maintain a healthy lifestyle, adults rely on their ability to walk while simultaneously managing multiple tasks that challenge their coordination. This study investigates the impact of cognitive dual-task on lower limb muscle activities in 21 healthy young adults during both gait initiation and steady-state gait. We utilized wireless electromyography sensors to measure muscle activities, along with a 3D motion capture system and force plates to detect the phases of gait initiation and steady-state gait. Participants were asked to walk at their self-selected pace, and we compared single-task and dual-task conditions. We analyzed mean muscle activation and co-contraction in the biceps femoris, vastus lateralis, gastrocnemius, and tibialis anterior muscles. The findings revealed that during gait initiation with the dual-task condition, there was a decrease in mean muscle activation and an increase in mean muscle c-contraction between the swing and stance limb compared to the single-task condition. In steady-state gait, there was also a decrease in mean muscle activation in the dual-task condition compared to the single-task condition. When participants performed dual-task activities during gait initiation, early indicators of reduced balance capability were observed. Additionally, during dual-task steady-state gait, knee stabilizer muscles exhibited signs of altered activation, contributing to balance instability.

Stumbling during gait is commonly encountered in patients who suffer from mild to serious walking problems, e.g. after stroke, in osteoarthritis, or amputees using a lower leg prosthesis. Instead of self-reporting, an objective assessment of the amount of stumbles in daily life would inform clinicians more accurately and enable the evaluation of treatments that aim to achive a safer walking pattern. An easy to use wearable might fullfill this need. The goal of the present study was to investigate whether a single inertial measurement unit (IMU) placed at the shank and machine learning algorithms could be used to detect and classify stumbling events in a dataset comprising of a wide variety of daily movements. Ten healthy test subjects were deliberately tripped by an unexpected and unseen obstacle while walking on a treadmill. The subjects stumbled a total of 276 times, both using an elevating recovery strategy and a lowering recovery strategy. Subjects also performed multiple Activities of Daily Living. During data processing, an event-defined window segmentation technique was used to trace high peaks in acceleration which could potentially be stumbles. In the reduced dataset, time windows were labelled with the aid of video annotation. Subsequently, discriminative features were extracted and fed to train seven different types of machine learning algorithms. Trained machine learning algorithms were validated using leave-one-subject-out cross-validation. Support Vector Machine (SVM) algorithms were most succesful, and could detect and classify stumbles with 100% sensitivity, 100% specificity and, 96.7% accuracy, in the independent testing dataset. The SVM algorithms were implemented in a user-friendly, freely available, stumble detection app named Stumblemeter. This work shows that stumble detection and classification based on SVMs is accurate and ready to apply in clinical practise.

Background: Gait analysis systems offer invaluable insights for rehabilitation, yet their expense limits clinician access. We developed GAITWell®, a low-cost modular system for capturing spatiotemporal gait variables, and evaluated its measurement properties. Methods: The GAITWell® uses discreet binary sensors on interconnected boards to collect gait data, which is then analyzed using the DBSCAN algorithm on the Cartesian points from sensor outputs. Reliability was assessed using ICC2,1, standard error of the mean (SEM) and Bland-Altman plots. Validity was determined by comparing GAITWell® with the Qualisys Pro-Reflex system. Results: Participated 38 healthy adults, with an average age of 33.2 years (SD 13.0). Correlations between GAITWell® and the Qualisys system ranged from moderate to very high for most gait variables, with the exception of stride length, which demonstrated a low but significant correlation (r = .360, p &lt; .05). The ICC2,1 indicated moderate to good agreement for most gait variables. Stance and double support times, cadence, and base of support exhibited poor reliability, characterized by larger SEM and limits of agreement. Conclusions: Our findings indicate that the GAITWell® system is a promising tool for gait analysis. Future research will enhance sensor accuracy and refine algorithms to improve reliability.

The deterioration of gait can be used as a biomarker for ageing and neurological diseases. Continuous gait monitoring and analysis are essential for early deficit detection and personalized rehabilitation. The use of mobile and wearable inertial sensor systems for gait monitoring and analysis have been well explored with promising results in the literature. However, most of these studies focus on the technologies for gait characteristic assessment, few of them have considered the data acquisition bandwidth of the sensing system. Inadequate sampling frequency will sacrifice signal fidelity, thus leading to an inaccurate estimation especially for spatial gait parameters. In this work, we developed an inertial sensor based in-shoe gait analysis system for real-time gait monitoring and investigated the optimal sampling frequency to capture all the information on walking patterns. An exploratory validation study was performed using an optical motion capture system on four healthy adult subjects, where each person underwent five walking sessions, giving a total of 20 sessions. Percentage mean absolute errors (MAE%) obtained in stride time, stride length, stride velocity, and cadence while walking were 1.19%, 1.68%, 2.08%, and 1.23%, respectively. In addition, an eigen-analysis based graphical descriptor from raw gait cycle signals was proposed as a new gait metric that can be quantified by principal component analysis to differentiate gait patterns, which has great potential to be used as a powerful analytical tool for gait disorder diagnostics.

To compare concentrations of endogenous N-acylethanolamines (NAEs) lipid mediators pal-mitoylethanolamide (PEA), oleoylethanolamide (OEA), and anandamide (AEA) in fresh, decon-taminated, cryopreserved and freeze-dried amniotic membrane (AM) allografts. Thereby deter-mining whether AM's analgesic and anti-inflammatory efficiency related to NAEs persists during storage. The concentrations of NAEs were measured using ultra-high-performance liquid chro-matography-tandem mass spectrometry. Indirect fluorescent immunohistochemistry was used to detect the PEA PPARα receptor. The concentrations of PEA, OEA, and AEA were significantly higher after decontamination. A significant decrease was found in cryopreserved AM compared to decontaminated tissue for PEA but not for OEA and AEA. However, significantly higher val-ues for all NAEs were detected in cryopreserved samples compared to fresh tissue before decon-tamination. The freeze-dried AM had similar values to decontaminated AM with no statistically significant difference. The nuclear staining of PPARα receptor was clearly visible in all specimens. The stability of NAEs in AM after cryopreservation was demonstrated under tissue bank storage conditions. However, a significant decrease, but still higher concentration of PEA compared to fresh not decontaminated tissue was found in cryopreserved, but not frieze-dried AM. Results in-dicate that NAEs persist during storage in levels sufficient for the analgesic and anti-inflammatory effects of AM allografts.

About 70% of children and adolescents with cerebral palsy experience gait impairments which affect their autonomy and well-being. Robotic-assisted gait training using the Lokomat is particu-larly promising for rehabilitation as it provides a standardized environment favoring the massive repetition of the movement, in which physical demands are low on the therapist and high training loads can be achieved. As no guidelines exist regarding training protocols and Lokomat settings, the goal of this study was to review the literature on Lokomat-assisted gait therapy and possibly make training recommendations. The twelve studies reviewed reported both positive and null effects of Lokomat training on gait. Half of the studies combined Lokomat with other types of training and only five used a control intervention to assess its benefit. Overall, training was administered 1-5 times per week for 20-60 minutes, over 1-12 weeks. Although Lokomat settings were not always described, progressively decreasing body-weight support and guidance, while increasing treadmill speed appear to be prioritized. The variety of training protocols and settings used did not allow pooling of the studies to assess effects of interventions on gait parameters in children and adoles-cents with cerebral palsy. This review highlights the need for homogenization of interventions so that clear guidelines can emerge and be applied in rehabilitation centers.

A portable, electrical impedance spectroscopy device to monitor the bioimpedance’s resistive component of beef meat by injecting a sinusoidal current of 1mA at 65.5 kHz was developed. In 4 slaughtered beef both right and left longissimus dorsi muscles where trimmed and left muscle portion was frozen to -18° C up to 7^th day while right one was meantime maintained at 5° C. Median value of specific resistivity of not-frozen sample was about twice Ω cm^-1 with respect of that of frozen-thawed sample (P = 0.004). It was concluded that the device is reliable to monitoring the ripening of beef meat in situ.

AbstractCadaver bone is possibly the most common transplant material used today. Common types of cadaver bone transplants are freeze-dried bone allografts and xenografts. Studies have shown that mineralized freeze-dried bone allografts have the same percentage of retained bone graft particles at different time points, indicating that these materials are never resorbed. However, it is commonly accepted by clinicians that these materials are resorbed and convert the graft site into normal bone. This histologic study was undertaken to determine the fate of mineralized freeze-dried bone allograft particles grafted into human extraction sockets. Materials and Methods:This study is a photographic, radiologic, and histological analysis of mineralized freeze-dried bone allograft healing in human sockets after mineralization at different time points. The mineralized freeze-dried bone allografts used for evaluation in this study were particulate bone graft materials in maxillary or mandibular extraction sockets. Patient selection was random, based on the following time periods: 6 months, 2 years, 5 years, 7 years, 10 years and 15 years. No block bone grafts were evaluated. Results:No resorption of cadaver bone graft particles was found at any time point. No osteoclasts were found in any of the histology at any time point. At different time points from 6 months through 15 years, mineralized freeze-dried bone allograft particles were found to be exfoliated out of the alveolar crest as a result of the formation of a hypervascular zone surrounding the grafted site. The embedded graft particles remain embedded in sclerotic bone until the particles reach the alveolar crest at which time the sclerotic bone and graft particles break up and are released into the gingiva. All histologic samples from 6 months to 15 years contained residual graft particles. The sclerotic bone formed around graft particles did not integrate to the graft particles or the implant surface. Conclusions:Mineralized freeze-dried bone allograft particles are not resorbed after mineralization. A hypervascular zone forms around the grafted site and exfoliates the bone graft particles into the gingiva. The mineralization process produces sclerotic bone which never remodels into normal bone. Sclerotic bone covers but does not integrate to the retained bone graft particles or implant surface resulting in a weakened structure with an increased likelihood of bone failure and implant loss.

In recent years, both domestic and international research on quadruped robots has advanced towards high dynamics and agility, with a focus on high-speed locomotion as a representative motion in high-dynamic activities. Quadruped animals like cheetahs exhibit high-speed running capabilities, attributed to the indispensable role played by their flexible spines during the flight phase motion. This paper establishes dynamic models of quadruped robots with different degrees of spine flexibility, providing a parameterized description of the flight phase motion for both rigid trunks and flexible spine quadruped robots. By setting different initial values for the spine joint and calculating the flight phase results for both types of robots at various initial velocities, the study compares and analyzes the impact of a flexible spine on the flight phase motion of quadruped robots. Through comparative experiments, the research aims to validate the influence of a flexible spine during the flight phase motion, providing insights into how spine flexibility affects the flight phase motion of quadruped robots.

This study examines the effects and durability of postural exercise on gait kinematics in people with intellectual and developmental disabilities (IDD). Thirty-four men with mild IDD were assigned to either the training group (n = 19) or the control group (n = 15). The TG performed the intervention over 8 weeks, 3 days/week, 1 h/day. The results indicated that the intervention program had a significant effect on some variables of gait. Also, in the TG between post-test and follow-up, there was no significant difference, which indicated that gait variables were maintained by the TG one month after the end of the program. This study provides evidence that postural exercises can be used as an effective intervention for improving gait in individuals with IDD.

Background Some patients with mild cognitive impairment (MCI) experience gait disturbances. However, there are few reports on the relationship between gait disturbance and cognitive function in patients with MCI. Therefore, we investigated the neural correlates of gait characteristics related to cognitive dysfunction. Methods Eighty patients diagnosed with MCI from three dementia centres in Gangwon-do, Korea were recruited for this study. We defined MCI as a Clinical Dementia Rating global score of 0.5 or higher, with a memory domain score of 0.5 or greater. The patients were classified as having either early or late MCI based on their Mini Mental Status Examination z-scores. Multiple logistic regression analysis was performed to examine the association between the gait characteristics and cognitive impairment. Analyses included variables such as age, sex, years of education, number of comorbidities, body mass index and height. Results Gait velocity, step count, step length, heel-to-heel base support, swing and stance phase duration, and support time were associated with cognitive function. A decrease in gray matter volume in the right pericalcarine area was associated with gait characteristics related to cognitive dysfunction. An increase in the curvature of gray matter in the right entorhinal, right lateral orbitofrontal, right cuneus, and right and left pars opercularis areas was also associated with gait characteristics related to cognitive dysfunction. Conclusion Since gait impairment is an important factor in determining activities of daily living in patients with mild cognitive impairment, the evaluation of gait and cognitive functions in patients with mild cognitive impairment is important.

Studies on the gait's parameters have been identified on the patients population. Most researchers confirm that the patients walk differently than normal people and they may have a risk for falls. Consistent finding and description of gender, age, and body mass index differences in gait studies is rare in healthy subjects. A cross-sectional study with forty-five young adult (F = 20, M = 25) was conducted. Stadiometer and Physilog 4 inertial sensors were used for data collection. A gait analyser 5.2 software (GaitUp, S.A. Lausanne, Switzerland) was used to determine spatiotemporal parameters. No statistically significant differences were found in any bilateral foot gait parameters with respect to gender, age, and body mass index. Females are found with higher total double support and cadence than males. Cadence also increases with age. Obese people showed lower gait speed, cadence, and total double support. These findings may be beneficial to those who have abnormal gait pattern due to age, body mass index differences, decreased muscle strength, spasticity, and joint mobility. This important informations should be considered to rehabilitate patients with abnormal gait patterns to controlling dynamic balance and riks to falling.

Understanding the motor patterns underlying the movement of people with Parkinson's disease (PD) is fundamental to the effective targeting of non-pharmacological therapies. This study aims to analyze the gait pattern in relation to the evolutionary stage between I-II and III-IV according to the Hoehn and Yahr scale (H&amp;Y) in people affected by PD. The study was conducted with the participation of 37 PD patients, with a mean age of 70.09±9.53 years, and of whom 48.64% were women. The inclusion criteria were: 1. To be diagnosed with PD; 2. To be in an evolutionary stage of the disease of between I and IV and; 3. To be able to walk independently and without any assistance. Kinematic and spatial-temporal parameters of the gait were analyzed. The results show differences in speed of movement, cadence, stride length, support duration, swing duration, step width, walking cycle duration and double support time between the stages analyzed. These results confirm the differences in PD gait pattern between stages I-II and III-IV. Different behaviors of the same variable were recorded depending on whether the right or left sides were affected by PD.

This study investigated the effects of freeze-thaw cycles on the mechanical properties of hardened self-compacting concrete for varying column heights. A column (100×20×300 cm) was fabricated by C30 self-compacting concrete in the laboratory and 10 cube samples (10x10x10 cm) were taken from fresh concrete as the references. After a period of 28 days, 160 core specimens (Ø67 mm in diameter) were taken from different column heights. Unit weight, water absorption, compressive strength, and freeze-thaw tests were performed on these 170 (10 reference cubic and 160 core) samples. The mechanical properties of the core specimens before freeze-thaw and after 8-56 freeze-thaw cycles were reported for varying column heights. The average compressive strength value of the reference cubic samples was determined as 40.28 MPa, while the compressive strengths of the core specimens before freeze-thaw were ranged from 40.25 MPa to 49.62 MPa, impying an increase in compressive strength values up to 23.18% compared to the reference cubic samples. Compressive strengths of the specimens subjected to 8 and 56 freeze-thaw cycles varied between 38.71‒48.07 MPa and 31.72‒39.11 MPa, respectively. Statistical analysis revealed that the compressive strength of the concrete exposed to 56 freeze-thaw cycles was significantly different from that of the other specimens.

This study investigated the effects of freeze-thaw cycles on the mechanical properties of hardened self-compacting concrete for varying column heights. A column (100×20×300 cm) was fabricated by C30 self-compacting concrete in the laboratory and 10 cube samples (10x10x10 cm) were taken from fresh concrete as the references. After a period of 28 days, 160 core specimens (Ø67 mm in diameter) were taken from different column heights. Unit weight, water absorption, compressive strength, and freeze-thaw tests were performed on these 170 (10 reference cubic and 160 core) samples. The mechanical properties of the core specimens before freeze-thaw and after 8-56 freeze-thaw cycles were reported for varying column heights. The average compressive strength value of the reference cubic samples was determined as 40.28 MPa, while the compressive strengths of the core specimens before freeze-thaw were ranged from 40.25 MPa to 49.62 MPa, impying an increase in compressive strength values up to 23.18% compared to the reference cubic samples. Compressive strengths of the specimens subjected to 8 and 56 freeze-thaw cycles varied between 38.71‒48.07 MPa and 31.72‒39.11 MPa, respectively. Statistical analysis revealed that the compressive strength of the concrete exposed to 56 freeze-thaw cycles was significantly different from that of the other specimens.

Freeze-drying is a well-established process in biomedical engineering for the fabrication of three-dimensional open-porous medical devices, especially those based on biopolymers. One of the most used biopolymers in this field is collagen, the most abundant protein in the human body and the main component of the extracellular-matrix, as well as its derivatives. Freeze-dried collagen-based sponges with a wide variety of attributes can be produced by design and have led to a wide range of successful commercial medical devices, foremost for dental, orthopedic, hemostatic and neuronal applications. However, this is still considered a high-cost and time-consuming process that is often used in a non-optimized manner. By combining advances in other technological fields, the opportunity arises to further evolve this process in a sustainable manner, and optimize the resulting products as well as create new opportunities in this field.

Abstract: Thermostability of vaccines, particularly enveloped viral vectored vaccines, remains a challenge for their delivery wherever needed. Freeze-drying of viral vectored vaccines is a prom-ising approach but remains challenging due to the water removal process from the outer and in-ner parts of the virus. In the case of enveloped viruses, freeze-drying induces increased stresses on the envelope, which often leads to inactivation of the virus. In this study, we design a method to freeze-dry a recombinant Vesicular Stomatitis Virus (VSV) expressing the SARS-CoV-2 spike glycoprotein. Since the envelope of VSV is composed of 50% lipid and 50% protein, the formula-tion study focused on both the protein and lipid portions of the vector. Formulations were pre-pared primarily using sucrose, trehalose, and sorbitol as cryoprotectants; mannitol as a lyopro-tectant; and histidine as a buffer. Initially, the infectivity of rVSV-SARS-CoV-2 and cake stability were investigated at different final moisture contents. High recovery of the infectious viral titer ( 0.5 to 1 log loss) was found at 3-6% moisture content with no deterioration of the freeze-dried cakes. To further minimize infectious viral titer loss, the composition and concentration of the ex-cipients were studied. An increase from 5 to 10% of both cryoprotectants and lyoprotectant, to-gether with the addition of 0.5% gelatin, resulted in the improved recovery of infectious virus titer and stable cake formation. Moreover, the secondary drying temperature of the freeze-drying pro-cess showed a significant impact on the infectivity of rVSV-SARS-CoV-2. The infectivity of the vector declined drastically when the temperature was raised above 20°C. Throughout a long-term stability study, formulations containing 10% sugar (sucrose/trehalose), 10% mannitol, 0.5% gelatin, and 10 mM of histidine showed satisfactory stability for six months at 2-8°C. The development of this freeze-drying process and the optimized formulation minimizes the need for a costly cold chain distribution system.

AYUMI EYE is an accelerometer-based gait analysis device that measures the 3D accelerations of the human trunk. This study investigated the measurement accuracy of the AYUMI EYE as hardware as well as the accuracy of the gait cycle extraction program via simultaneous measurements using AYUMI EYE, a ground reaction force (GRF), and an optical motion capture system called VICON. The study was conducted with four healthy individuals as participants. The gait data were obtained by simulating four different patterns for three trials each: normal walking, anterior-tilt walking, hemiplegic walking, and shuffling walking. The AYUMI EYE and VICON showed good agreement for both the acceleration and displacement data. The durations of subsequent stride cycles calculated using the AYUMI EYE and GRF were in good agreement based on the calculated cross-correlation coefficients (CCs) with an r value of 0.896 and p-value less than 0.05, and their accuracies for these results were sufficient.

Running on a non-motorized, curved-deck treadmill is thought to improve gait mechanics. It is not known, though, if the change in gait carries over to running on a motorized treadmill or level ground. To determine the effect of running on a curved non-motorized treadmill (CNT) on gait characteristics measured during a subsequent bout of running on a traditional motorized treadmill (TMT). Sixteen healthy college-aged participants, age (mean±SD) 20.4±1.6 years volunteered to have their gait analyzed while running on a TMT and CNT. After familiarization and warm-up on both treadmills, each subject completed five, 4-minute bouts of running alternating between traditional motorized and curved non-motorized treadmills: TMT-1, CNT-1, TMT-2, CNT-2, and TMT-3. Variables of interest included step length (m), stride length (m), imbalance score (%), and step angle (°) and were measured using Optogait gait analysis equipment. Differences in gait char acteristics among TMT-1, TMT-2, and TMT-3 can be attributed to running on the CNT. The results show that running on a CNT resulted in significant changes in gait characteristics. These findings suggest that running on a CNT can significantly alter gait characteristics may result in improvements in running gait that persist to subsequent running on a TMT.

People with diabetic foot frequently exhibit poor gait and balance. However, there is no review to inform digital biomarkers of poor gait and balance related to diabetic foot, measurable by wearables outside traditional gait laboratories. Such information could assist in designing remote patient monitoring platform to track changes in gait and balance dysfunction among people with diabetic foot for timely referral and intervention. Accordingly, we conducted a web-based review using PubMed. Our search was limited to human subjects and English-written papers published in peer-reviewed journals. We identified 20 papers in this review. We found preliminary evidence of digital biomarkers of gait and balance dysfunction in people with diabetic foot, measured by wearables, such as slow gait speed, large gait variability, unstable gait initiation, and large body sway. However, due to heterogeneities in included papers in terms of study design, movement tasks, and small sample size, more studies are recommended to confirm this preliminary evidence. Additionally, based on our review, we recommend establishing appropriate strategies to successfully implement wearable-based assessment into clinical practice for diabetic foot care.

One control challenge in prosthetic legs is seamless transition from one gait mode to another. User intent recognition (UIR) is a high-level controller that tells a low-level controller to switch to the identified activity mode, depending on the user’s intent and environment. We propose a new framework to design an optimal UIR system with simultaneous maximum performance and parsimony for gait mode recognition. We use multi-objective optimization (MOO) to find an optimal feature subset that creates a trade-off between these two conflicting objectives. The main contribution of this paper is two-fold: (1) a new gradient-based multi-objective feature selection (GMOFS) method for optimal UIR design; and (2) the application of advanced evolutionary MOO methods for UIR. GMOFS is an embedded method that simultaneously performs feature selection and classification by incorporating an elastic net in multilayer perceptron neural network training. Experimental data are collected from six subjects, including three able-bodied subjects and three transfemoral amputees. We implement GMOFS and four variants of multi-objective biogeography-based optimization (MOBBO) for optimal feature subset selection, and we compare their performances using normalized hypervolume and relative coverage. GMOFS demonstrates competitive performance compared to the four MOBBO methods. We achieve a mean classification accuracy of 97.14% ± 1.51% and 98.45% ± 1.22% with the optimal selected subset for able-bodied and amputee subjects, respectively, while using only 23% of the available features. Results thus indicate the potential of advanced optimization methods to simultaneously achieve accurate, reliable, and compact UIR for locomotion mode detection of lower-limb amputees with prostheses.

Gait abnormalities are one of the distinguishing symptoms of patients with Parkinson's disease (PD) that contribute to fall risk. Our study compares the gait parameters of people with PD when they walk through a predefined course without assistance, with a conventional walker, and with a motorized walker under different speed cues. Six PD subjects were recruited at the New York Institute of Technology College of Osteopathic Medicine to participate in this study. Spatial posture and gait data of the test subjects were collected via a VICON motion capture system. We developed a framework to process and extract gait features and applied statistical analysis on these features to examine the significance of the findings. The results showed that motorized walkers with haptic cues significantly improved gait symmetry of PD subjects. Specifically, the asymmetry index of the gait cycle time was reduced from 6.7% when walking without assistance to 0.56% and below when using a walker. Furthermore, the double support time of a gait cycle was reduced by 4.88% compared to walking without assistance.

Immobilized metal ion affinity adsorbents have been widely used in separation technique to purify proteins. Due to the leakage of metal ion from the adsorbents, there is no metal ion affinity adsorbent for hemoperfusion has been applied to clinical trial. In this study, in order to prevent the leakage of Zn²⁺ loaded from cellulose beads based adsorbent, improve its stability and adsorption capacity for testosterone, Freeze-drying method was used to enhance the porosity of cellulose beads, improve the surface area of the cellulose beads and adsorption capacity for testosterone. Chitosan was used to coat the adsorbents for preventing the leakage of Zn²⁺ loaded and improve the adsorbent’s stability. Moreover, the factors affecting adsorption ability and some components in plasma were also investigated. The results indicate the adsorption ability of the adsorbent can be significantly improved by freeze-drying. After the adsorbent was coated with 0.02% chitosan solution, the highest adsorption percentage reached 48%. During adsorption, the Zn²⁺ concentration in plasma did not rise. In addition, the adsorption percentage for total proteins was below 15%. The results may be caused by the pore size and surface area of the adsorbent enlarged via freeze-drying, and the chitosan solution went into the pores and coated the outer and inner surface of the adsorbent. The adsorbent has a potential clinical application to remove testosterone in patients with recurrent and metastatic prostate cancer.

Human footprint is having a unique set of ridges unmatched by any other human being, and therefore it can be used in different identity documents for example birth certificate, Indian biometric identification system AADHAR card, driving license, PAN card, and passport. There are many instances of the crime scene where an accused must walk around and left the footwear impressions as well as barefoot prints and therefore it is very crucial to recovering the footprints to identify the criminals. Footprint-based biometric is a considerably newer technique for personal identification. Fingerprints, retina, iris and face recognition are the methods most useful for attendance record of the person. This time world is facing the problem of global terrorism. It is challenging to identify the terrorist because they are living as regular as the citizens do. Their soft target includes the industries of special interests such as defense, silicon and nanotechnology chip manufacturing units, pharmacy sectors. They pretend themselves as religious persons, so temples and other holy places, even in markets is in their targets. These are the places where one can obtain their footprints easily. The gait itself is sufficient to predict the behaviour of the suspects. The present research is driven to identify the usefulness of footprint and gait as an alternative to personal identification.

Background: This systematic review aimed to provide a comprehensive overview of the effects of Functional Electrical Stimulation (FES) on gait characteristics in healthy individuals. Methods: Six electronic databases (PubMed, Embase, Epistemonikos, PEDro, COCHRANE Library, Scopus) were searched for studies evaluating the effects of FES on spatiotemporal, kinematic and kinetic gait parameters in healthy individuals. Two examiners evaluated the eligibility and quality of included studies using the PEDro scale. Results: A total of 15 studies met the inclusion criteria. Findings from the literature reveal that FES can be used to modify lower-limb joint kinematics, i.e., to increase or reduce the range of motion of hip, knee and ankle joints. In addition, FES can be used to alter kinetics parameters, including ground reaction forces, center of pressure trajectory, or knee joint reaction force. As a consequence of these kinetics and kinematics changes, FES can lead to changes in spatiotemporal gait parameters, such as gait speed, step cadence, and stance duration. Conclusion: The findings of this review improve our understanding of the effects of FES on gait biomechanics in healthy individuals, and highlight the potential of this technology as a training or assistive solution for improving gait performance in this population.

The purpose of the present study was to investigate the effect of the laterally moving tactile stimuli to the sole on the anticipatory postural adjustment (APA) of the gait initiation. Thirteen healthy males participated in this study. A sound cue was provided at the beginning of each trial. The moving tactile stimuli were delivered to the sole after the start cue. The loci of the tactile stimuli moved from the left to right most side of the sole, and then moved from the right to left most side of that in a stimuli cycle. The duration of one stimuli cycle was 960 ms, and this cycle repeated 16 times in a trial. The participants made three steps forward from quiet stance at the participants' preferred time after the start cue. The APA did not onset at the specific direction or phase of the moving tactile stimuli, indicating that they did not use the stimuli as a trigger for initiating the gait. The moving tactile stimuli decreased the amplitude and increased the duration of the APA. The moving tactile stimuli increased the time between the APA onset and toe-off of the initial support leg, indicating that they moved slower when initiating gait during the moving tactile stimuli. Those findings are explained by the view that suppression of the APA induced by the moving tactile stimuli to the sole is caused by the decrease in the velocity of the gait initiation, and the slower velocity of the gait initiation is caused by masking tactile sensation of the sole.

Crouch gait is a motor complication commonly associated with cerebral palsy, spastic diplegia, stroke, and motor-neurological pathologies, broadly defined as knee flexion in excess of 20° in the gait cycle. Uncorrected crouch gait results in fatigue, joint degradation, and loss of ambulation. Torsion springs have been used in cycling to store energy in knee flexion to reduce fatigue in the quadriceps during knee extension. SolidWorks was used to design a passive exoskeleton for the knee, incorporating torsion springs of stiffnesses 20,000 N/mm and 30,000 N/mm at the knee joint to correct four different crouch gaits. OpenSim was used to gather data from moments produced and knee angles from each crouch gait and the normal gait. Motion analysis of the exoskeleton was simulated using knee angles for each crouch gait and compared with moments produced with the normal gait moments in the stance phase of the gait cycle. All crouch gait moments were significantly reduced, and the correction of peak crouch moments was achieved corresponding to the normal gait cycle during the stance phase. These results offer significant potential for nonsurgical and less invasive options for wearable exoskeletons in crouch gait correction.

The way in which a person walks, known as human gait, is a significant indicator of overall health and well-being. Abnormalities in gait can indicate the presence of metabolic disorders, such as diabetes or obesity. However, detecting these disorders can be challenging using traditional methods, which often involve subjective assessments or invasive procedures. In this study, a novel methodology known as Criticality Analysis (CA) was proposed for the detection and monitoring of human gait in people with metabolic disorders taking part in an intervention to increase activity and reduce weight. The CA approach utilised inertial measurement unit gait data, alongside clinical health measures. This allows for the control of nonlinear growth in the system, resulting in lower dimensional, nonlinear, free-scale, stable, controlled, and organised trajectories. These trajectories were then analysed using a Support Vector Machine (SVM) algorithm, which is well-suited for this task due to its ability to handle nonlinear and dynamic data. The combination of the CA approach and the SVM algorithm demonstrated high accuracy and non-invasiveness in detecting metabolic disorders, yielding an average accuracy within the range of 78.2% to 90%. Additionally, the classification technique accuracy, at a group level was observed to reduce during period of the intervention (e.g., from week 2 to week 3) alongside changes in fitness and health, which indicates the potential of using the approach to measure and monitor biological systems. As such, this novel methodology has the potential to be a valuable tool for healthcare professionals in detecting and monitoring metabolic disorders, as well as other unknown diseases associated with the human biological system.

Motor functions are deteriorated by aging. Some conditions may magnify this deterioration. To examine whether hemodialysis (HD) process would negatively impact gait and balance beyond diabetes condition among mid-age adults (48-64 years) and older adults (65+ years). One hundred and ninety-six subjects (age=66.2±9.1 years, body-mass-index=30.1±6.4 kg/m², female=56%) in 5 groups were recruited: mid-age adults with diabetes undergoing HD (Mid-age HD+, n=38) and without HD (Mid-age HD-, n=40); older adults with diabetes undergoing HD (Older HD+, n=36) and without HD (Older HD-, n=37); and non-diabetic older adults (Older DM-, n=45). Gait parameters (stride velocity, stride length, gait cycle time, and double support) and balance parameters (ankle, hip, and center of mass sways) were quantified using validated wearable platforms. Groups with diabetes had overall poorer gait and balance compared to the non-diabetic group (p<0.050). Among people with diabetes, the HD+ had significantly worsened gait and balance when comparing to the HD- (Cohen’s effect size d=0.63-2.32, p<0.050). Between-group difference was more pronounced among older adults with the largest effect size observed for stride length (d=2.32, p<0.001). Results suggested that deterioration in gait speed among the HD+ was correlated with age (r=-0.440, p<0.001), while this correlation was diminished among the HD-. Interestingly, results also suggested that poor gait in the Older HD- related to poor balance, while no correlation was observed between poor balance and poor gait among the Older HD+. Using objective assessments, results confirmed that the presence of diabetes can deteriorate gait and balance, and this deterioration can be magnified by HD process. Among non-HD people with diabetes, poor static balance described poor gait. However, among people with diabetes undergoing HD, age was a dominate factor describing poor gait irrespective of static balance. Results also suggested feasibility of using wearable platforms to quantify motor performance during routine dialysis clinic visits. These objective assessments may assist in identifying early deterioration in motor function, which in turn may promote timely intervention.

Concentration and preservation of lactic acid bacteria (LAB) starter cultures for food production guarantee the long-term delivery of stable cultures in terms of viability and functional activity. One method that has commonly been used to prepare dried starter cultures for food applications is freeze-drying. During freeze-drying, the bacterial cells are exposed to stresses such as freezing, drying, and long-term exposure to low-water activity. Additionally, another added stress is introduced during the rehydration process. The purpose of this study was to evaluate the survival rates and fermentation performance of three (3) freeze-dried lactic acid bacterial cultures previously isolated from Ghanaian traditional fermented milk. LAB cultures, i.e., Lactobacillus delbrueckii, Lactococcus lactis and Leuconostoc mesenteroides were frozen in the chamber of a Telstar (Lyoquest) laboratory freeze dryer for 10 hrs at -55 °C (as single and combined cultures) using skimmed milk and cassava flour as cryoprotectants held in plastic or glass cryovial. For viability during storage, freeze-dried LAB cultures were stored in a refrigerator (4 °C) and at room temperature (25 °C) for 4-weeks. The survival of freeze-dried cultures was determined by growth kinetics at 600nm (OD₆₀₀). The performance of freeze-dried LAB cultures after 4-weeks storage was determined by their growth and acidification of milk during yogurt fermentation and consumer sensory evaluation of fermented milk using a 9-point hedonic scale. The survival rates for LAB ranged between 60.11% and 70.91% following freeze-drying. For single cultures, the highest survival was recorded for Lactobacillus delbrueckii (L12), whereas for combined cultures, the highest survival was observed for Lactococcus lactis (L3) combined with Lactobacillus delbrueckii (L12). During the fermentation process all the freeze-dried LAB cultures were able to acidify yogurt to a pH below 4, while yogurt produce from the spontaneous fermentation was characterized by low acidification. Yogurt fermented with freeze-dried lactic acid bacteria cultures, either single or combined strains, showed improved acceptability as compared to the spontaneously fermented yogurt. The consumer acceptability results showed that yogurts produced with combined starter culture of Lactoccus lactis and Lactobacillus delbrueckii or single culture of Lactococcus lactis were the most preferred products with Lactococcus lactis and Lactobacillus delbrueckii possessing high survival rates and high consumer acceptability in yogurt production. These findings are crucial and can be adopted for large-scale production and commercialization of yogurt production, however, in-depth investigation on the effects of freeze-drying and long-term storage on survival and performance of selected LAB cultures are needed.

We conducted this study to determine the potential cryopreservative effects of different hesperidin (vitamin P; HSP) doses on ram semen after freeze-thawing. Semen samples were obtained from Sönmez rams by an artificial vagina. The samples were divided into six groups: control, 10, 50, 100, 250, and 500 µg/mL HSP (C, HSP10, HSP50, HSP100, HSP250, and HSP500, respectively). At the end of the study, sperm motility and kinetic parameters, plasma membrane acrosome integrity (PMAI), high mitochondrial membrane potential (HMMP), viability, lipid peroxidation levels (LPL), chromatin damage, oxidant parameters, and antioxidant parameters were assayed. None of the doses of HSP added to the semen extender showed any enhancing effect on progressive motility compared to C (p>0.05). In fact, HSP500 had negative effects (p<0.05). Moreover, PMI activities were the highest at the HSP10 dose, while LPL values were the lowest (p<0.05). The doses of HSP10 and HSP50 added to the Tris extender medium showed positive effects on spermatozoon chromatin damage. Consequently, we can say that HSP doses used in this study are not effective on semen progressive motility, but the HSP10 dose is effective on PMAI and chromatin damage by reducing LPL.

The purpose of this scoping review was to examine the literature on the use of anti-gravity treadmill and its effects on lower limb motor functions in children and adolescents with locomotor impairments. Four databases (MEDLINE, CINAHL, Embase, Web of Science) were searched for articles from inception to August 2021. Inclusion criteria were: (1) experimental or quasi-experimental studies using the anti-gravity training as the primary intervention; (2) studies conducted in paediatricpediatric participants; (3) articles reporting outcomes related to the lower limb functions; and (4) studies published in French or English. Fifteen articles were included in the review. Studies included children and adolescents aged 4–18 years with locomotor impairments. The intervention duration was ranged from 2 and to 12 weeks, with 2-5 sessions per week. Included studies showed reported that anti-gravity training induces improvements in muscle strength, balance, spatiotemporal gait parameters, and walking endurance in children with locomotor impairments. This review provides relevant information about the modalities, outcomes and limits associated with the anti-gravity training protocol reported in the literature. Overall, the anti-gravity treadmill training could be viewed as a valuable training modality for children with cerebral palsy. However, more precise, and comprehensive description of anti-gravity rehabilitation protocols would be useful.

Background and Objectives: Sports medicine, orthopaedic and rehabilitation physicians use gait analysis and goniometry to evaluate and diagnose patients with neuro-musculo-skeletal diseases. Goniometry is a measuring method that shows the joint’s range of motion. Three-dimensional goniometry has been used in order to assess the patients in a kinematic manner, but they are not affordable, so, phone apps come handy to any orthopaedic or rehabilitation physician so we can have a clear image of the progress made by the patient after the rehabilitation program or should something happen and the patient cannot come to the facility, such as the Covid-19 pandemic, when some orthopaedic and most of the rehabilitation facilities have been temporarily closed. Midstance has been chosen as the moment of the gait evaluation in this paper since it has an important role in stability. The objective of this paper is to figure out if the measurements taken during midstance at the knee joint of the subjects can be statistically significant and used during usual examinations. Materials and Methods: Four groups of subjects: patients suffering from hip, knee, hip and knee osteoarthritis and a control group volunteered their participation, being asked to normally walk while their gait was recorded and uploaded into Angles App – a phone based videogoniometer. Results: Patients suffering from hip osteoarthritis have a higher knee angle on the right side than the ones suffering from knee osteoarthritis, hip and knee osteoarthritis and the control group. Female patients suffering from hip osteoarthritis also presented a more flexed knee than the ones suffering from knee osteoarthritis and the ones in the control group, the knee flexion presenting itself as a compensation mechanism. Conclusion: Video goniometry can help us make an orthopaedic, rehabilitation or neurology database for each assessment with constant updates of the evolution of the osteoarthritis patient’s treatment.

An ongoing EU Horizon 2020 Project called BionicVEST is investigating the effect of constant electrical stimulation (ES) of the inferior vestibular nerve in patients with bilateral vestibular dysfunction (BVD)[1]. The evidence is that constant ES results in improved postural stability and gait performance and so the question of central importance is how could constant ES of mainly saccular afferents in these BVD patients cause this improved performance? We suggest that the constant ES is substituting for the absent saccular neural input to the vestibular nuclei and the cerebellum in these BVD patients and indirectly via these structures to other structures which have been of great recent interest in motor control. One target area, the anterior midline cerebellum (the uvula) has recently been targeted as a location for deep brain stimulation in human patients to improve postural stability and gait. There are projections from midline cerebellum to basal ganglia including the striatum, structures involved in the initiation of gait. It may be that the effect of this activation of peripheral saccular afferent neurons is analogous to the effect of deep brain stimulation (DBS) by electrodes in basal ganglia acting to help alleviate the symptoms of patients with Parkinson's disease.

This article delves into the complex landscape of Bitcoin halving events, analyzing the historical context and implications of these pivotal occurrences within the cryptocurrency ecosystem and on its sustainability within the landscape of financial technologies. Through an examination of past halving events in 2012, 2016, and 2020, this study meticulously scrutinizes the conditions and prices of Bitcoin before and after each halving. By synthesizing data and trends from previous events, this article aims to uncover patterns and insights that illuminate the impact of Bitcoin halving on market dynamics and sustainability, movement of the price level, reached peaks and price troughs. Furthermore, this research presents a comparative analysis of past halving events, drawing parallels and distinctions to elucidate the evolving nature of Bitcoin's price movements and market sentiment surrounding these milestone events. Looking towards the future, this study estimates predictions and expectations for the upcoming Bitcoin halving. By unraveling the intricate relationship between Bitcoin halving events and market behavior, this article seeks to provide a comprehensive understanding of the broader implications for Bitcoin's trajectory and the evolving landscape of the cryptocurrency market and its sustainability.

In the context of evaluating physical function in individuals with stroke, the 3-meter backward walk test (3MBWT) emerges as a potential tool of interest. The purpose of this study was to assess the test-retest reliability and construct validity of the 3MBWT and its correlation with falling incidents. Conducted in a neurological rehabilitation center, 35 ambulatory individuals with stroke were enrolled within a month post-stroke onset. These participants, with a Functional Ambulation Category score of ≥4, underwent the 3MBWT, Functional Gait Assessment (FGA), 10-Meter Walk Test (10MWT), and 6-Minute Walk Test (6MWT) three times by different physiotherapists. Results indicated the 3MBWT displayed high reliability (r=0.97-0.98) and showed significant construct validity with other established walking tests like the 6MWT (r=-0.78) and 10MWT (r=0.71), with a moderate correlation to the FGA (r=-0.54). No marked differences in test outcomes were observed between participants based on their fall history. Conclusively, the 3MBWT proves to be highly reliable and validates well with existing walking function assessments for stroke patients, suggesting its potential as a time-efficient alternative.

The paper focuses on the application of a multilevel, integrative and territorial approach to the protection of cultural heritage through planning instruments in Serbia. It points out the problems of the sectoral approach and discusses international recommendations that can be integrated into the planning methodology. The case study is the area of Djerdap National Park, which has an already established international and national importance. The research suggests that the cultural heritage in the area, with the exception of the Roman limes, is still recognized at the level of individual localities. The study emphasizes the importance of aligning all levels of governance to safeguard the whole spatial entity rather than focusing solely on its particular areas. The interna-tional and national importance of the planning area contributes to the strengthening of awareness of heritage and its institutional protection. However, the vitality of the area, which is key to its sustainable development, comes from the local level. Planning documents contribute to the inte-gration of local values and local communities into development programs and projects.

Superior fiber quality is one of the most important objectives in cotton breeding. To detect the genetic basis underlying fiber quality, an F2 population containing 413 plants was constructed by crossing Jifeng 914 and Jifeng 173, both of which have superior fiber quality, with Jifeng 173 being better. Five fiber quality traits were investigated in the F2, F2:3, F2:4, and F2:5 populations. Quantitative trait loci (QTL) mapping was conducted based on a high-density genetic map containing 11,488 single nucleotide polymorphisms (SNPs) and spanning 4,202.12 cM in length. Transgressive segregation patterns and complex correlations in the five tested traits were observed. A total of 108 QTLs were found, including 27 for fiber length (FL), 16 for fiber strength (FS), 24 for micronaire (MC), 17 for fiber uniformity (FU), and 24 for fiber elongation rate (FE). Chromosome A7 contained 12 QTL, ranking the first. No QTL was found on chromosome D1 and D11. Each QTL contributed 1.98%–21.45% to the phenotypic variation (PV), including 13 major effect QTLs that contributed more than 10% toward PV. Two QTLs could be repeatedly detected in three populations, including qFL-D3-2 in F2, F2:4, and F2:5 with 9.18%–21.45% of PV, qFS-A11-1 in F2:3, F2:4 and F2:5 with 6.05%–10.41% of PV. Another seven stable QTLs could be detected in two populations, including four major effect QTLs: qFL-A12-3, qFS-D10-2, qMC-D6-2, and qMC-D8-1. Fourteen QTL-overlapping regions were found, which might explain the complex correlations among the five phenotypic traits. Four regions on chromosome A11, D3, D6, and D10 covered by both stable and major effect QTLs are promising for further fine mapping. The genomic regions of the two QTLs detected in three populations and the four major effect QTLs contain 810 genes. Gene functional analysis revealed that the annotated genes are mainly involved in protein binding and metabolic pathways. Fifteen candidate genes in the qFL-D3-2 region are highly expressed in fiber or ovules during fiber initiation, elongation, secondary cell wall thickening, or maturation stages. qRT-PCR revealed that Ghir_D03G005440.1 and Ghir_D03G011310.1 may play a role in promoting fiber initiation, Ghir_D03G006470.1 may be beneficial for promoting fiber elongation. This study provides more information for revealing the molecular genetic basis underlying cotton fiber quality.

In recent years, electroencephalogram (EEG) emotion recognition has emerged as a research hotspot in the field of artificial intelligence (AI). Despite advancements in EEG-based emotion recognition, room for enhancing performance persists due to EEG signal redundancy and limitations in feature extraction, leading to inefficient models and emotional information loss. To fully utilize EEG's emotional information and improve recognition accuracy while reducing computational costs, this paper proposes a Convolutional-Recurrent Hybrid Network with a dual-stream adaptive approach and an attention mechanism (CSA-SA-CRTNN). Firstly, the model utilizes a CSAM module to assign corresponding weights to EEG channels. Then, an adaptive dual-stream convolutional-recurrent network (SA-CRNN and MHSA-CRNN) is applied to extract local spatial-temporal features. After that, the extracted local features are concatenated and fed into a temporal convolutional network with a multi-head self-attention mechanism (MHSA-TCN) to capture global information. Finally, the extracted EEG information is used for emotion classification. We conducted binary and ternary classification experiments on the DEAP dataset, achieving 99.26% and 99.15% accuracy for arousal and valence in binary classification, and 97.69% and 98.05% in ternary classification, surpassing relevant algorithms. Additionally, the model's efficiency is significantly higher than other models, achieving better accuracy with lower resource consumption.

The Simultaneous Localization And Mapping (SLAM) scanner is an easy and portable Light Detection And Ranging (LiDAR) data acquisition device. Its main output is a 3D point cloud covering the scanned scene. Regarding the importance of accuracy in the survey domain, this paper aims to assess the accuracy of two SLAM scanners: the NavVis VLX and the BLK2GO Scanner. This assessment is conducted for both outdoor and indoor environments. In this context, two types of reference data are used: the Total Station (TS) and the static scanner Z+F Imager 5016. To carry out the assessment, four comparisons are tested: cloud to cloud, cloud to mesh, mesh to mesh, and edge detection board assessment. However, the results of the assessments confirm that the accuracy of indoor SLAM scanner measurements (5 mm) is greater than that of outdoor ones (between 10 mm and 60 mm). Moreover, the comparison of cloud to cloud provides the best accuracy regarding direct accuracy measurement without manipulations. Finally, based on the high accuracy, scanning speed, flexibility, and the accuracy differences between tested cases, it is confirmed that SLAM scanners are effective tools for data acquisition.

The profile of secondary metabolites occurring in apple cuticular layer is not only characteristic for particular apple cultivar, but also dynamically reflects various external factors in growing environment. In this study, the possibility to authenticate apple samples based on analysis of their cuticular layer extracts was investigated. Ultra-high-performance liquid chromatography coupled to high resolution tandem mass spectrometry (UHPLC-HRMS/MS) was employed for obtaining metabolomic fingerprints. In total, 274 authentic apple samples, four cultivars harvested within the seasons 2020 to 2022 in the Czech Republic and Poland were analysed. The generated complex data processed by univariate and multivariate statistical methods enabled to build classification models for discrimination of apple cultivars as well as their geographical origin. The models showed very good performance in differentiation of Czech and Polish samples for three of four cultivars: ‘Gala’, ‘Golden Delicious’ and ‘Idared’, moreover, the validity of the models was verified over harvest seasons. The diagnostic markers, besides metabolites of triterpene biosynthetic pathway, mainly represented wax esters. ‘Jonagold’, which is known to be susceptible to mutations, was the only cultivar for which the unambiguous classification of geographical origin was not possible.

Pyrops candelaria is one of the common pests of fruit trees, but the research on the pathogenic microorganisms it may carry is very limited. Therefore, it is essential to reveal the pathogenic microbes it carries and their potential hazards. This study found a new virus from the transcriptome of P. candelaria, which was first reported in P. candelaria and named as PyCaV (Pyrops candelaria associated virus). RACE and bioinformatics assay revealed that the full-length of PyCaV is 10855 bp with the polyA tail, containing a single open reading frame (ORF) encoding a polyprotein consisting of 3171 amino acid (aa). The virus has a typical Iflavirus structure, including two rhv domains, a RNA helicase domain (HEL), a 3C cysteine protease domain (Pro), and a RNA-dependent RNA polymerase domain (RdRp). Further phylogenetic analysis revealed that this virus belongs to family Iflaviridae and sequence alignements analysis suggedted PyCaV is new member in unassigned genus of family Iflaviridae. Further in-depth analysis of virus-infection-part showed that PyCaV is distributing in the whole longan lanternfly, including its head, chest, and abdomen, but more PyCaV was identified in the chest. The distribution of PyCaV in different parts of P. candelaria was further explored, which showed that more PyCaV were detected in its piercing-sucking mouthparts and chest viscera. Statistical analysis showed that the PyCaV infection was affected by time and locations.

Accurately estimating a person's age is crucial for identity verification at all critical checkpoints, including airports, land borders, and seaports. Human gait may be used as a biometric identifier and indicator of age, among other things. This study aims to develop methods for estimating a person's age by observing their walk. In this paper, a novel technique for preprocessing the proposed gait dataset has been used by utilizing a combination of the gait energy image (GEI), the accumulated frame difference energy image (AFDEI), and the invariant moment of the image. The proposed technique outperformed state-of-the-art methods in terms of accuracy. The proposed method was tested and evaluated using a convolutional neural network (CNN), and it achieved an average accuracy of 90.35% across 14 different view angles within 5 K-Fold, the proposed method resulted in 94.68% and 94.54% in 30º and 75º view degree respectively. concluding that the approach is effective and promising for estimating age using human gait.

The aim of this retrospective study was to compare the clinical outcomes of treating isolated surgical neck fractures of the humerus using either the intramedullary nail or the MIROS (Minimally Invasive Reduction and Osteosynthesis System®) system. The study included 42 patients who underwent surgical treatment at the Polyclinic from January 2014 to June 2020. The results indicated that both treatments were effective; however, the MIROS system exhibited a higher complication rate. Intramedullary nailing was more reliable, thus recommended as the primary treatment method. This study underscores the importance of selecting the appropriate fixation technique to minimize complications and enhance patient outcomes.

As the world population grows, fulfilling the need for biomaterials in the healthcare system becomes increasingly important. Biomaterials, which include metals, polymers, ceramics, and composites, play an important role in the creation of medical devices that improve people's lives. The European Society for Biomaterials described biomaterials as non-biological materials used in medical devices to interact with biological systems. This definition has developed to encompass materials that treat, assess, or replace tissues or bodily functions. Biocompatibility, as defined by the FDA, is a key feature of biomaterials, as is the requirement to fulfil design requirements such as mechanical performance, geometry, and electrical control. Over the last decade, advances in regenerative medicine and tissue engineering have boosted biomaterials' usage in medical applications dramatically. Despite its promise, scientists, engineers, and physicians continue to face significant challenges due to the complexity of biomaterials. Biomaterials have various benefits, including biodegradability, non-toxicity, and biocompatibility, making them extremely useful for replacing, sustaining, or improving biological activities in damaged tissues. They are used in a wide range of applications, including tissue engineering implants, human tissue healing and regeneration, medication delivery systems, and biosensors. This study gives insights into the fundamental characteristics, case studies, and ethical issues associated with the usage and use of biomaterials, further examining their potential and significance in healthcare and medicine.

Background: The bacterium Capnocytophaga spp. is a part of the oral microbiome of dogs, which has zoonotic potential. This study aimed to assess factors that influence the prevalence of Capnocytophaga cynodegmi and Capnocytophaga canimorsus in Wrocaw’s dog population. Methods: Molecular detection (PCR) involved 105 swabs, examining parameters such as oral cavity condition, underlying health issues, recent antibiotics, age, medications, material collection, and dog chews. Results: The study highlighted significant associations between the presence of Capnocytophaga cynodegmi and oral cavity condition, material collection method, and use of dog’s chews. Conclusions: Correlations obtained in this study between the oral health of Wroclaw's dog population and the presence of Capnocytophaga cynodegmi suggest its significance in the oral microbiome of dogs. Limitations, including the small sample size, highlight the need for more research to comprehensively understand additional factors that affect the prevalence of Capnocytophaga spp. in dogs

Gait is a basic cognitive propositive action that has been shown to be altered in late stages of neurodegenerative dementias. Nevertheless, alterations are less clear in mild forms of dementia, and the potential use of gait analysis as a biomarker of initial cognitive decline has hitherto mostly been neglected. We here report the results of a study of gait kinematic time series for two groups of patients (Mild Cognitive Impairment and mild Alzheimer's disease) and a group of matched control subjects. Two metrics based on permutation patterns are considered, respectively measuring the complexity and irreversibility of the time series. Results indicate that kinematic disorganisation is present at early phases of cognitive impairment; in addition, they depict a rich scenario, in which some joint movements display an increased complexity and irreversibility, while others a marked decrease. Beyond their potential use as biomarkers, complexity and irreversibility metrics can open a new door towards the understanding of the role of the nervous system in gait, as well as its adaptation and compensatory mechanisms.

Tussilago farfara L. is a traditional medicinal plant valued for its potentially health-promoting metabolites. Its herbal raw material has been recognized and used since ancient times and continues to be widely used in traditional medicine. Introducing these plants to in vitro cultivation is a challenging task, but once the protocol is developed, such cultures can provide an abundant and inexhaustible source of plant material. In this study, we report the successful induction and growth of vigorous T. farfara L. callus in vitro. Callus induction was achieved on solid media in darkness, whereas it appeared inefficient under light conditions and in suspension culture. We present a detailed description of callus growth kinetics, morphological analysis, photosynthetic activity and biochemical parameters (including protein content and photosynthetic pigments) supported by histological studies. Furthermore, we observed potential for organogenesis and somatic embryogenesis. This method for in vitro propagation of T. farfara, along with callus culture maintenance, offers a wide range of applications in pharmacy and could benefit the environment by minimizing the depletion of natural populations of this species.

Excess nitrogen in agricultural drainage poses a serious threat to the water quality safety of the Yellow River basin. Utilizing aquatic plants to modify the rhizosphere microbial community structure and facilitate nitrogen transformation is a crucial strategy for mitigating regional water eutrophication. Our results revealed that the denitrification rate (DR), dissimilatory nitrate reduction to ammonium rate (DNRAR) and nitrogen fixation rate (NFR) of rhizosphere sediments exhibited a significant increase in artificially cultivated ditch. Compared with those in natural ditches, the richness of the bacterial community and the relative abundances of Bacteroidota, Verrucomicrobiota, Firmicutes, Anaeromyxobacter and Geobacter, which are involved mainly in the nitrogen cycle, in the rhizosphere sediments of artificially cultivated ditch were significantly greater due to improvements in environmental conditions. In artificially cultivated ditch, the dominant functional genes affecting DRNARs in the rhizosphere sediments of P. australis were nrfC and nrfA, while DRs were driven mainly by norB and napA, which were influenced by the nitrogen and carbon levels; and the dominant functional genes affecting NFRs in the rhizosphere sediments of T. orientalis were nifD, nifK and nifH. Our results provide a scientific basis for the use of aquatic plants for mitigating excess nitrogen levels in agricultural drainage.

Background: Educating college students about the importance of good sleep habits could lead to the adoption of healthier sleep routines, including sufficient sleep duration and sleep quality. The current pre-post study examines the impact of completing a sleep education program called “Sleep 101” on (1) sleep hygiene practices, (2) sleep quality, and (3) weekday and weekend sleep behaviors among college students. “Sleep 101” is an interactive online course developed to educate college students about the importance of sleep by addressing basic sleep physiology, the impact of sleep on mood, academic and physical performance, the interactions between sleep and various substances, and common sleep disorders. Methods: 338 college students were recruited from a midsized public university in the US and invited to participate in “Sleep 101”, of which 25 participants completed the baseline and post-intervention questionnaire. The Sleep Hygiene Index (SHI) was utilized to evaluate sleep hygiene practices, while standard questions were employed to assess weekday and weekend sleep behaviors and overall sleep quality. Results: Those who completed the study demonstrated a significant increase in weekday sleep duration and were less likely to engage in negative prior bedtime activities. In addition, 40% of those who completed baseline and post-intervention assessments noticed improvements in their sleep quality. Conclusion: These findings suggest that a brief online program is beneficial in improving sleep behaviors among college and could be a scalable approach to addressing current sleep issues and preventing future sleep problems in college students.

Strawberry root rot caused by Neopestalotiopsis clavispora is one of the main diseases of strawberry and significantly impacts the yield and quality of strawberry fruit. There are now no effective control techniques available except for fungicide sprays, which may directly impact consumers. Biological control is becoming an alternative method for the control of plant diseases to replace or decrease the application of traditional synthetic chemical fungicides. Trichoderma is widely used as a biological agent for controlling strawberry root rot. In order to provide resources for screening the highly effective biocontrol fungus for controlling strawberry root rot caused by Neopestalotiopsis clavispora, the biocontrol mechanism,the control effects of Trichoderma asperellum CMT10 against strawberry root rot and growth-promoting effects on strawberry seedlings were investigated by plate culture, microscopy observation and root drenching methods.The results showed that CMT10 had obvious competitive, antibiotic and hyperparasitism effects on Neopestalotiopsis clavispora CMGF3. The CMT10 could quickly occupy nutritional space, and the inhibition rates of CMT10 against CMGF3 in confrontation culture on 7 d was 65.49%. The inhibition rates of volatile metabolite and fermentation metabolite produced by CMT10 against CMGF3 were 79.67% and 69.84%, respectively. The mycelium of strain CMT10 can act as hyperparasites by making contacting, winding and penetrating hyphae of CMGF3. Pot experiment showed that the biocontrol efficacy of CMT10 on strawberry root rot caused by Neopestalotiopsis clavispora was 63.00%. CMT10 had obvious promotion effect on strawberry growth, the plant height, root length, total fresh weight, root fresh weight, stem fresh weight and root dry weight, with the promotion rates were 20.09%, 22.39%, 87.11%, 101.58%, 79.82% and 72.33%, respectively. Overall, this study showed the ability of Trichoderma asperellum CMT10 to control strawberry root rot and their potential to develop as novel biocontrol agents to replace chemical fungicides for eco-friendly, sustainable agriculture.

The properties of the annual, semiannual and triennial oscillations (AO, SAO and TO) in the middle atmosphere have been investigated using the TIMED/SABER temperature data. The Lomb-Scargle and wavelet spectra were used to determine the dominant oscillations in the background temperature field. The AO is prominent at the mid-latitudes. The AO amplitudes present an asymmetry between the two Hemispheres, being larger in the mesosphere than in the stratosphere. The SAO dominates the tropical regions, with three amplitude maxima at altitudes of 45, 75, and 85 km. The SAOs in the upper mesosphere (75 km) are out of phase with those in the mesopause (85 km) in the tropical regions, which can generate an enhancement of 11 K at each equinox, contributing to the lower mesospheric inversion layer. The TO is significant in the tropical region, with amplitude being maximum at 35, 45 and 85 km. Result shows that there may be potential interaction by the TO with SAO at 85km at the equator. The relation between ENSO and TO has also been discussed. The ENSO signal may modulate the amplitude of the TO, mainly in the lower stratosphere. The real origin of the TO may lie in the wave-mean-flow interaction.

In this paper we study a class of impulsive delayed neural networks with parameter uncertainties and reaction-diffusion terms. Using the properties of M-matrices and some inequality techniques, some sufficient conditions are derived to guarantee the global exponential stability of the given system. The results obtained are presented by simple algebraic inequalities, which are certainly more concise than previous methods. Finally, the validity and usefulness of our results are illustrated by arithmetic examples.

Climate change is challenging the agricultural sector worldwide. The pressure exerted by the altered thermal conditions drives the zonal shift for various cultivations. This study presents the multiyear analysis of the Growing Degree Days (GDD) index over the Northern Mediterranean Basin (NMB), focused on the high-value vine cultivation derived from the E-OBS dataset. To handle this extensive environmental dataset, R-language scripts and packages were applied, along with the capabilities of the GIS software. The investigated time period spans from 1969 to 2018, and the performed analysis indicates a broad shift/expansion in areas of GDD exceeding 2000 heat units. The extracted results specify the viticultural areas where the GDD index surpasses the suitable values for vine cultivation, owing to the increase of the thermal stress risk. In addition to mapping areas with GDD ≥ 2000, spatial calculations of the surface of areas meeting this criterion per country in the study area were made. In the northern parts of the NMB, the rise of the GDD index values indicates the establishment of vine plantations in the future.

The studied solar pot is a recent invention, which gained a utility model protection in 2021 from the Hungarian Intellectual Property Office under patent number 5489. The device is made for environmentally friendly cooking or heating (by utilizing solar energy) of foods and liquids. Its structure is similar to a double pipe heat exchanger, it has an outer mantle and an inner cooking tank. The goals of the paper are proposing a new physically-based mathematical model describing the solar pot and carrying out computer experiments with it, assembling an experimental system of the pot connected with a solar collector and performing measurements on it. Based on the results, the solar pot can successfully be used for cooking or sterilizing foods or liquids during the studied time period, in Hungary.