Garnet-type Ta-doped Li7La3Zr2O12 (LLZO) ceramic solid electrolytes with Ga2O3 additive were synthesized via a conventional solid-state reaction process. When the amounts of Ga2O3 additive were below 2 mol %, the sintered sample has a dense structure composed of grains with the averaged size of 5 to 10 μm, while 3 mol % or more Ga2O3 addition causes the significant increase in grain size above several 10 to 100 μm, due to the sintering with large amount of liquid Li-Ga-O phase at high temperature. The highest total (bulk + grain-boundary) ionic conductivity of 1.1 mS cm1 at room temperature was obtained in the sample with 5 mol % Ga2O3 addition. However, in galvanostatic testing of the symmetric cell with Li metal electrodes, this sample was shorted by Li dendrite growth into solid electrolyte at current density below 0.2 mA cm2. The tolerance for Li dendrite growth is maximized in sample sintered with 2 mol % Ga2O3 addition, which was shorted at 0.8 mA cm2 in the symmetric cell. Since the interfacial resistance between Li metal and solid electrolyte was nearly identical among the all samples, the difference in tolerance for Li dendrite growth is mainly attributed to the difference in microstructure of sintered samples depending on the amounts of Ga2O3.

β-Ga2O3 is a well-known semiconductor material for power devices and other applications. Recently, β-Ga2O3 has also been reported as a scintillator material with a light yield of approximately 8400 ph./MeV, scintillation decay time of <1 μs, and density of 6.44 g/cm3. In this study, 2-inch diameter β-Ga2O3 single crystals were prepared by oxide crystal growth using the cold crucible (OCCC) method under various oxygen partial pressures. In the OCCC method, as in the cold crucible method, a high frequency is applied directly to the oxide materials, which are heated and melted, and the melt is held by the outermost solid material itself that is cooled by water using a copper hearth. In the OCCC method, crystal growth is performed while rotating the seed crystal, as in the Czochralski method, to increase the crystal diameter. The optical properties and radiation responses of the crystals grown under various oxygen partial pressures were evaluated.

The development of sensors for monitoring Carbon Monoxide (CO) in a large range of temperature is of crucial importance in areas as monitoring of industrial processes or personal tracking using smart objects. Devices integrating GaN/Ga₂O₃ core/shell nanowires (NWs) is a promising solution allowing combining the high sensitivity of the electronic properties to the states of GaN-core surface; and the high sensitivity to CO of Ga₂O₃-shell. Because the performances of sensors primarily depend on the material properties composing the active layer of the device, it is essential to control these properties and in first time its synthesis. In this work, we investigate the synthesis of GaN/Ga₂O₃ core-shell NWs with a special focus on the formation of the shell. The GaN NWs grown by Plasma-assisted molecular beam epitaxy, are post-treated following thermal oxidation to form Ga₂O₃-shell surrounding the GaN-core. We establish that the Ga₂O₃-shell thickness can be modulated from 1 up to 14 nm by changing the oxidation conditions, and follows the diffuse-controlled reaction. By combining XRD-STEM and EDX analysis, we also demonstrate that the oxide shell formed by thermal oxidation is crystalline and presents the β-Ga₂O₃ crystalline phase, and is synthesized in epitaxial relationship with the GaN-core.

No matter where we reside, the issue of greenhouse gas emissions impacts us all. Their influence has a disastrous effect on the earth's climate, producing global warming and many other irreversible environmental impacts, even though it is occasionally invisible to the independent eye. Phase change materials (PCMs) can store and release heat when it is abundant during the day (e.g., from solar radiation), for use at night, or on chilly days when the building needs to be heated. As a consequence, buildings use less energy to heat and cool, which lowers greenhouse gas emissions. Consequently, research on thermally active medium-density fiberboard (MDF) with PCMs is presented in this work. MDF is useful for interior design and furniture manufacturing. The boards were created using pine (Pinus sylvestris L.) and spruce (Picea abies L.) fibers, urea-formaldehyde resin, and PCM powder, with a phase transition temperature of 22 oC, density of 785 kg m−3, the latent heat capacity of 160 kJ kg−1, the volumetric heat capacity of 126 MJ m−3, the specific heat capacity of 2.2 kJ kgK−1, the thermal conductivity of 0.18 W mK−1, and a maximum operating temperature of 200 °C. Five variants of MDF with PCM additive were developed: 0%, 5%, 10%, 30%, and 50%. According to the study, scores at the MOR, MOE, IB, and Screw Withdrawal Resistance (SWR) tests decreased when PCM content was added. However, the results of the thickness swelling and water absorption tests indicate that the PCM particles do not exhibit a substantial capacity to absorb water, retaining the dimensional stability of the MDF boards. The panel's thermal characteristics improved with increasing PCM concentration, according to the data. The density profiles of all the variations under consideration had a somewhat U-shaped appearance; however, the version with a 50% PCM content had a flatter form and no obvious layer compaction on the panel surface. Therefore, certain of the mechanical and physical characteristics of the manufactured panels can be enhanced by a well-chosen PCM addition.

Redox mediators comprising I–, Co3+, and Ti3C2Tx MXene were applied to dye-sensitized solar cells (DSCs). In the as-prepared DSCs (I-DSCs), wherein hole conduction occurred via the redox reaction of I−/I3− ions, the power conversion efficiency (PCE) was not altered by the addition of Ti3C2Tx MXene. The I-DSCs were exposed to light to produce Co2+/Co3+-based cells (Co-DSCs), wherein the holes were transferred via the redox reaction of Co2+/Co3+ ions. A PCE of 9.01% was achieved in a Co-DSC with Ti3C2Tx MXene (Ti3C2Tx-Co-DSC), which indicated an improvement from the PCE of a bare Co-DSC without Ti3C2Tx MXene (7.27%). It was also found that the presence of Ti3C2Tx MXene in the redox mediator increased the hole collection, dye regeneration, and electron injection efficiencies of the Ti3C2Tx-Co-DSC, leading to an improvement in both the short-circuit current and the PCE when compared with those of the bare Co-DSC without MXene.

Six bacterial strains with differing abilities to produce varying concentrations of Indole Acetic Acid were tested individually and in consortia for plant growth promoting and fitness related traits of Cicer arietinum. In all experiments the presence of the nitrogen fixer Mesorhizobium ciceri resulted in increased biomass production. In the absence of this strain, IAA Psedomonas putida and Bacillus megaterium hinder plant growth and fitness related traits. The application of mixes of the three strains always resulted in better plant performance when M. ciceri was present. Whereas P. putida has a noticeable plant growth-promoting effect B. megaterium resulted less effective. The low levels of IAA produced by the selected strains had a significantly greater positive effect on plant biomass accumulation, flower, pods and seed production as well as on total plant nitrogen and nitrogen concentration in seed than high IAA producer strains.

β-Ga2O3 crystal have attracted great attentions in the fields of photonics and photoelectronics because of its ultra wide-band gap and high thermal conductivity. Here, pure β-Ga2O3 crystal was successfully grown by optical floating zone (OFZ) method, and used as saturable absorbers to realize a passively Q-switched all-solid-state 1μm laser for the first time. By placing the as-grown β-Ga2O3 crystal into the resonator of Nd:GYAP solid-state laser, a Q-switched pulses at the center wavelength of 1080.4 nm are generated under a output coupling of 10%. The maximum output power is 191.5 mW while the shortest pulse width is 606.54 ns, and the maximum repetition frequency is 344.06 kHz. The maximum pulse energy and peak power are 0.567 μJ and 0.93 W, respectively. Our experimental results show that β-Ga2O3 crystal has great potential in the development of all-solid-state 1μm pulsed laser.

(1) Background: The definition of value addition is based on the process or processes which are used to transform physically the initial raw material in the final food or non-food article. Diversification can enhance the possibility of increased gains. The aim of this work is to give a reliable description of value addition when speaking of coconut-based beverages among all possible derivatives; (2) Methods: a systematic review of main papers on the argument has been critically examined and discussed; (3) Results: Processing degree is a consequence of consumers’ requests. Three different drivers for value addition have been considered: packaging, durability, and size options; sensorial features; and sustainability. Results of this investigation have highlighted the added value of several products because of recyclable packaging materials, intermediate or long durability expectations, different available sizes, and good or excellent sensorial performances; (4) Conclusions: There are different value-added coconut-based beverages with interesting perspectives. On the other side, sustainability and eco-friendly policies may be a problem for those products which are produced similarly to non-coconut based beverages. The opportunity of certified organic and/or fair-trade products could help the industry of coconuts in the next future. More research is still needed in this ambit.

Forward-bias hole injection from 10 nm-thick p-type Nickel Oxide layers into 10 um-thick n-type Gallium Oxide in a vertical NiO/Ga2O3 p-n heterojunction leads to more than a factor of 2 enhancement of photoresponse measured from this junction. While it takes only 600 seconds to obtain such a pronounced increase in photoresponse, it persists for hours, indicating feasibility of photovoltaic device performance control. The effect is ascribed to charge injection-induced increase of minority carrier (hole) diffusion length (resulting in improved collection of photogenerated non-equilibrium carriers) in n-type beta-Ga2O3 epitaxial layers, due to trapping of injected charge (holes) on deep meta-stable levels in the material and subsequent blocking of non-equilibrium carrier recombination through these levels. Suppressed recombination leads to increased non-equilibrium carrier lifetime, in turn determining a longer diffusion length and being the root-cause for the effect of charge injection.

We report the electrical properties of Al0.3Ga0.7N/GaN heterojunction field effect transistor (HFET) structures with a Ga2O3 passivation layer grown by metal-organic chemical vapor deposition (MOCVD). In this study, three different thicknesses of Ga2O3 dielectric layers were grown on Al0.3Ga0.7N/GaN structures leading to metal-oxide-semiconductor-HFET or MOSHFET structures. X-ray diffraction (XRD) showed the (¯201) orientation peaks of -Ga2O3 in the device structure. The van der Pauw and Hall measurements yield the electron density of ~ 4 x1018 cm-3 and mobility of ~770 cm2V-1s-1 in the 2-dimensional electron gas (2DEG) channel at room temperature. Capacitance-voltage (C-V) measurement for the on-state 2DEG density for the MOSHFET structure was found to be of the order of ~1.5 x1013 cm-2. The thickness of the Ga2O3 layer was inversely related to the threshold voltage and the on-state capacitance. The interface charge density between the oxide and Al0.3Ga0.7N barrier layer was found to be of the order of ~1012 cm2eV-1. The annealing at 900° C of the MOSHFET structures revealed that the Ga2O3 layer was thermally stable at high temperatures resulting in insignificant threshold voltage shifts for annealed samples with respect to as-deposited (unannealed) structures. Our results show that the MOCVD-gown Ga2O3 dielectric layers can be a strong candidate for stable high-power devices.

Introduction of Cl- and O- atoms into C4-vinyl carbocations was studied by X-ray diffraction analysis and IR spectroscopy. Chlorine atoms are weak electron acceptors in ordinary molecules, but within vinyl carbocations, manifest themselves as strong electron donors that accept a positive charge. The attachment of a Cl atom directly to a C=C bond leads to an increase in the e-density on it, exceeding that of the common double bond. The positive charge should be concentrated on the Cl atom, and weak δ- may appear on the C=C bond. More distant attachment of the Cl atom—to a C atom adjacent to the C=C bond—has a weaker effect on it. If two Cl atoms are attached to the Сγ atom of the vinyl cation, as in Cl2СγСδHСαHCH3, then the cation switches to the allyl type with two practically equivalent and almost uncharged СγСδСα bonds. When such a strong nucleophile as the O atom is introduced into the carbocation, a protonated ester molecule with a C-O(H+)-C group and a C=C bond forms. Nonetheless, in the future, there is still a possibility of obtaining carbocations with a non-protonated C-O-C group.

Gallium oxide (Ga2O3) is an emerging wide bandgap semiconductor promising a wide range of important applications. However, mass production of high-quality crystalline Ga2O3 still suffers from limitations associated with poor reproducibility and low efficiency. Low-temperature grown amorphous Ga2O3 demonstrates comparable performance with its crystalline counterparts. Lanthanide Er3+-doped Ga2O3 (Ga2O3: Er) possesses great potential for developing light-emitting devices, photodetectors and optical waveguides. The host circumstance can exert a crystal field around the lanthanide dopants and strongly influence their photoluminescence properties. Here we present a systematical study of the impact of amorphous-to-crystalline transition on the upconversion photoluminescence in Ga2O3: Er thin films. Through controlling the growth temperature of Ga2O3: Er films, the upconversion luminescence of as-grown thin films are strongly enhanced over 100 times. Moreover, the variation of photoluminescence reflects the amorphous-to-crystalline transformation of the Ga2O3: Er thin films. These results will aid further design of favorable optoelectronic devices integrated with lanthanide-doped Ga2O3 thin films.

Jacobian theta function identities are related to the Addition formula for the Weierstrass 1 Sigma function. In this paper, from the Addition formula for Weierstrass Sigma function, new and 2 simple proofs of four square sums theorem are given. Using the addition formula of the theta func- 3 tions, we also give simple proofs of two square sums and eight square sums theorem.

Starting from acid chlorides, alkynes, tryptamines, and acroyl chloride, 21 densely substituted tetrahydro-beta-carbolines are prepared in a four-component one-pot reaction. In this study, the aza-Michael addition step to generate intermediate enaminones is optimized in the presence of ytterbium triflate. Moreover, apart from acroyl chloride, all reactants can be deployed in almost equimolar ratios, which increases the atom economy of the sequence. For mechanistic rationali-zation, the concluding aza-anellation was investigated by DFT calculations on potential inter-mediates and corresponding activation energies, revealing that the aza-anellation rather pro-ceeds via ene-reaction than via electrocyclization.

The manufacturing parameters influence the properties of thermo-mechanically processed met-als such as Mg alloys. This paper presents how the mechanical properties, the microstructure and the degradation rate of extruded Mn-containing Mg-Gd-alloys can be modified. Gd as repre-sented REE-element is particularly interesting due to the influence on the texture development in Mg and therefore studied as a base alloy system. The contents of Gd were investigated be-tween 2 to 9 wt.% with Mn-addition of 0.5 and 1.0 wt.%. The grain sizes and the corresponding textures were modified by the extrusion parameters and the alloy content. It was shown that modification by Mn can decrease the grain size, but increase the degree of recrystallization and decrease the degradation rate in the biological medium compared to the binary Mg-Gd system from previous studies. The results suggest that the binary Mg-Gd system can be produced more efficiently by adding Mn and that the resulting properties are more robust.

In typical Cobalt-chromium (CoCr) alloys powders, aluminum oxide (Al₂O₃) powder can be added. In the present study, we successfully prepared alloyed samples of various powder ratios by laser cladding, and analyzed their microstructure and carbide structural characteristics, including microhardness, biological properties, morphology (using scanning electron microscopy), and crystal structure (using X-ray powder diffraction). Elemental distribution was also determined by energy-dispersive X-ray spectral analysis. The results showed that Al₂O₃ addition caused the alloy to change from slender columnar crystals to columnar grains similar, to equiaxed grains. In addition, Al₂O₃ agglomeration zones appeared, and carbide structures were altered. The mechanism of the observed performance changes was also analyzed.

An addition sequence is an important operation in many applications of computer science, such as multi-modular exponentiation and outsourcing protocols. Finding an addition sequence for a set of positive integers with the shortest length is challenging due to the high computational time required to find the solution. In this paper, a new metaheuristic algorithm is designed based on the simulated annealing strategy to generate a short addition sequence. The efficiency of the proposed algorithm was proved experimentally by comparing it with the previous exact and heuristic algorithms in terms of running time and the length of the addition sequence.

The main goal of this study was to introduce glycerol as a plasticizer to Polyvinyl Alcohol (PVA) membranes in order to increase their flexibility. The qualities of PVA membranes produced with various glycerol concentrations were evaluated. With the modified PVA membranes containing 5% glycerol, encouraging results were obtained. These membranes had superb optical characteristics and a 90% transmittance rate. This shows that the membranes are suited for applications needing excellent optical clarity since they permit light to travel through with little distortion. Importantly, FTIR analysis demonstrated that the addition of glycerol had no effect on the PVA membranes' chemical composition or structural integrity. In comparison to pure PVA Membrane, the modified membranes' water barrier qualities showed a considerable drop of up to 50%. The membranes are useful for applications requiring moisture management or breathability because of the decline, which points to an increase in permeability to water vapour. The large increase in flexibility, which was achieved by the PVA membranes containing 5% glycerol and beyond the brittleness typically associated with pure PVA, was a noteworthy discovery. The possible applications are expanded due to the increased flexibility, especially in industries where adaptability and flexibility are essential. Additionally, the addition of glycerol improved the thermal stability of the membranes, as they showed increased resistance to breakdown or decomposition at high temperatures. Additionally, the modified membranes' mechanical qualities were better than those of pure PVA, indicating that the glycerol addition improved their overall mechanical performance and tensile strength. PVA membranes were effectively made more flexible by adding 5% glycerol as a plasticizer. This led to membranes with superior optical qualities, reduced water barrier properties, greater flexibility, improved thermal stability, and maybe improved mechanical capabilities. These discoveries open up new opportunities for the use of these flexible PVA membranes in a range of settings, such as flexible packaging, biomedical materials, and other industries that need adaptive and flexible materials.

The aim of this study was to develop a ready-to-eat vegetable-herb mixes with high nutritional and sensory values, as well as good storability. In this regard the suitability of fresh herbs (peppermint, oregano, green basil, red basil, and parsley) was tested for use in mixes with fresh-cut iceberg lettuce. Lettuce-herb mixtures were stored for 6 days at 5°C. The reason for the decrease in the appearance of the salads was the browning of the cut surface of the lettuce, as well as discoloration on the cut herbs. Comparing the storage ability of cut herbs, red basil and parsley retained the best appearance for 6 d at 5 °C. A small addition of herbs to fresh-cut iceberg lettuce caused a significant increase in contents of pro-health ingredients in the mixes. There were large discrepancies in the sensory quality of the mixes, but the highest quality and consumer acceptance were found for salads with parsley (5% and 10%) and red basil (5%). After harvest, the fresh herbs were more contaminated by molds than the iceberg lettuce. Bacterial, yeast and mold contamination increased during storage, but the rate of mold growth was much lower in the mixes with parsley compared to lettuce alone.

In this study, the effects of various beryllium (Be) addition (Be-free, 0.1, 0.25, 0.50 wt.%) on the microstructure, mechanical properties, and corrosion corrosion of the Al-Mg-Li alloys were systematically investigated. The best performance was obtained in alloy with 0.1 wt.% Be addition. Trace Be addition promotes the grain refinement of the as-cast alloy ingot and contributes positive effects to the recrystallization, bringing improvement of tensile property. Meanwhile, the best anti-corrosion behavior is also presented at 0.1 wt.% Be addition, due to its potential to reduce the width of precipitates free zone (PFZ). As the Be content increase to an excessive level, the comprehensive performance decreases. Therefore, it is strongly recommended that adding trace Be element into Al-Mg-Li alloys has a positive effect on the comprehensive service performance.

Fresh potatoes were deep-fried in olive oil (OO) & extra virgin olive oil (EVOO) and their blends with 5%, 10% and 20% v/v sesame oil (SO). This is the first report on the use of sesame oil as natural source of antioxidant for olive oil deep-frying. Oil was evaluated for Peroxide Value (PV), Free Fatty Acids (FFA), K₂₃₂, K₂₇₀, Trolox Equivalent Antioxidant Capacity (TEAC) and Total Phenols (TP) until Total Polar Compounds (TPCs) reached 25%. Sesame lignan transformations were monitored through Reverse-phase HPLC. While TPCs in olive oils increased at a steady rate, the addition of 5%, 10% and 20% v/v SO created a time window lasting 1, 2 and 3 hours, respectively, where TPCs were constant. SO addition to OO increased the total frying time. Furthermore, the addition of SO reduced the peroxides formation rate for both OO and EVOO. EVOO was more resistant to oxidation than OO as measured by TPCs and TEAC, while frying time raised from 21.5 to 25.25 h when EVOO replaced OO. The increase in frying time for olive oil but not for extra virgin olive oil, after SO addition, is pointing out a niche market for extra virgin olive oil in deep-frying.

Hydrogenated small fullerenes (Cn, n<60) are of interest as potential astrochemical species, and as intermediates in hydrogen catalysed fullerene growth. However computational identification of key stable species is difficult due to the vast combinatorial space of structures. In this study we explore routes to predict stable hydrogenated small fullerenes. We show that neither local fullerene geometry nor local electronic structure analysis are able to correctly predict subsequent low energy hydrogenation sites, and indeed sequential stable addition searches also sometimes fail to identify most stable hydrogenated fullerene isomers. Of the empirical and semi-empirical methods tested, GFN2-xTB consistently gives highly accurate energy correlation (r>0.99) to full DFT-LDA calculations at a fraction of the computational cost. This allows identification of the most stable hydrogenated fullerenes up to 4H for four fullerenes, namely two isomers of C28 and C40, via “brute force” systematic testing of all symmetry inequivalent combinations. The approach shows promise for wider systematic studies of smaller hydrogenated fullerenes.

The topic of modification of magnesium oxychloride cement (MOC) via specific functional additives is very much pronounced in the research of alternative building materials. This study deals with the co-doping of MOC by 1D and 2D carbon nanomaterials in order to improve its mechanical properties while using tannic acid (TA) as a surfactant. Furthermore, the effect of TA on MOC also covers the improvement of water resistance. As a filler, three size fractions of standard quartz sand are used. The proposed types of MOC-based composites show promising results considering their mechanical, macro- and microstructural, chemical, and hygric properties. The use of 1D and 2D nanoadditives and their mixture enables the improvement of the flexural strength and most of all softening coefficient, the durability parameter characterizing the resistance of the prepared materials to water. For samples immersed in water for 24 h, the compressive strength of all modified composites tested was higher than that of the reference composite. Quantitatively, the developed co-doped composite shows mechanical parameters comparable to or even better than those of commonly used Portland cement-based materials, while maintaining high environmental efficiency. This indicates its potential use as an environmentally friendly alternative to Portland cement-based products.

For this research, a comparative evaluation was performed in which the addition of 3D-printed biocarriers fabricated with 13X and Halloysite (13Χ-Η) and commercial Kaldnes K1 biocarriers were evaluated as opposed to the non addition of biocarriers in a semi-pilot scale MBBR-MBR unit. For the evaluation of the MBBR-MBR efficiency, various physicochemical parameters were measured while static light scattering and optical microscopy observations were additionally used. Biofilm extracted from the biocarriers was also evaluated. It was observed that in the MBBR-MBR K1 unit, the membrane filtration improved while in the MBBR-MBR 13X-H unit the membrane fouling rate was the same as in the control MBBR-MBR unit. This is due to the production of large amount of SMP which resulted from the large amount of biofilm created in the 13X-H biocarriers. An optimal biodegradation of the organic load was concluded for all three MBBR-MBR units. The nitrification and denitrification processes were improved at the MBBR-MBR units using 13X-H and K1. The dry mass produced on the 13X-H biocarriers was three orders of magnitude larger than that produced on the K1. Finally, it was observed that mostly EPS was produced in the biofilm of K1 biocarriers while in the biofilm of 13X-H mostly SMP.

Polydimethylsiloxane with hydroxy groups was functionalized to form functionalized polydimethylsiloxane, which subsequently underwent an addition reaction with isophorone diisocyanate to form the prepolymer. Next, 3-aminopropyltriethoxysilane (APTS) reacted with 3-glycidoxypropyltrimethoxysilane (GPTS) to produce bridged polysilsesquioxanes, and the sol–gel technology was employed to form hyperbranched polysiloxane nanoparticles with hydroxy groups, which was used as the additive. The hyperbranched polysiloxane and the prepolymer containing NCO functional groups then underwent an addition reaction to produce the hybrid materials. Fourier-transform infrared spectroscopy and 29Si nuclear magnetic resonance were used to characterize the structure of the polyurethane hybrid. Regarding thermal stability, after the hyperbranched polysiloxane nanoparticles was introduced, the integral procedural decomposition temperature increased from 348 ºC for polyurethane matrix to 859 ºC for the hybrid material. The results revealed that the thermal stability of the hybrid material substantially increased by approximately 247%.

A enantioselective tandem transformation concerning asymmetric allylic decarboxylative addition and cyclization of N-nosylimines with vinylethylene carbonates (VECs) in the presence of [Rh(C2H4)2Cl]2, chiral sulfoxide-N-olefin tridentate ligand has been developed. The reaction of VECs with various substituted N-nosylimines proceeded smoothly under mild conditions, giving highly functionalized oxazolidine frameworks in good to high yields with good to excellent enantioselectivity.

Compared to tin lead alloys, lead-free tin alloys have lower toxicity, making them more widely used. In this study, Sn-20Bi-0.3Al-xY solders alloys were prepared. The effects of the addition of Y on its microstructure, micro-hardness, wettability and mechanical properties was investigated. The result showed that the addition of Y had significant effect on the refinement of Sn-20Bi-0.3Al-xY. From the spreading tests results, Y increased the wettability of the solders, however when the fraction of Y gradually increased, the wettability reduced. The ultimate tensile and hardness of Sn-20Bi-0.3Al-xY solders alloys were increased as the content of Y increasing.

Soil is an extremely significant resource for human survival, and agglomerates, as the basic unit of soil structure, not only enhance soil fertility and control the biological validity of nutrients, but also strengthen the soil's erosion resistance. The mass application of fertilizers may have a significant impact on crop growth and soil structure, and the rational application and dispensing of fertilizers will be an urgent issue to be addressed. Therefore, the effect of fertilizer application on the stability of water-stable soil aggregates needs to be studied under different meteorological and soil conditions to draw more general and feasible conclusions. Our Meta-analysis of data from 220 of 56 published studies found that fertilizer application increased mean weight diameter (MWD) by an average of 18% compared to the no-fertilizer treatment. Among the nitrogen (N), phosphate (P), and organic (OM) fertilizer treatments, the organic fertilizer treatment had a greater stimulatory effect on MWD (26%). Among the different fertilizer levels, low level of phosphorus (<40kg·hm-2·yr-1), high level of N (>120kg·hm-2·yr-1), and low level of organic fertilizer (<5000kg·hm-2·yr-1) increased MWD by 19%, 14%, and 41% respectively. Across soil types and land use types, the response to MWD was positive for red soils and paddy fields, and the stimulatory effect of organic fertilizer was more significant compared to chemical fertilizer. The regression model showed that the response ratio of MWD was negatively correlated with the response ratio of soil pH and bulk density (BD), and positively correlated with the response ratio of soil organic carbon (SOC) and microbial mass carbon (MBC). Meanwhile, the PLS-SEM model showed that average annual temperature was the main factor affecting the stability of soil aggregates, and the average annual rainfall is the secondary factor. Therefore, this study found that the long-term use of organic fertilizers in place of some chemical fertilizers was more effective than chemical fertilizer alone. Temperature and rainfall have greater effects on the response of fertilizer to soil aggregate stability.

The narrow process window during intercritical annealing and discontinuous yielding have limited the commercialisation of medium Mn steels. In this study, a double annealing process based on the commercial continuous annealing line is proposed. The cold-rolled medium Mn steels were first fully austenitized and quenched during the first annealing, followed by the intercritical annealing for reverted austenite transformation. The microstructure of duplex lath-shaped austenite and ferrite is produced and the steel exhibit a desirable continuous yielding during tensile deformation. Al is added into the medium Mn steel to enlarge the process window and to improve partitioning efficiency of Mn. The produced steel is more robust with temperature fluctuation during the industrial process due to the enlarged intercritical region. Mn partitioning is more efficient owing to elevated annealing temperature, which results in the improvement of ductility in the Al-added steel with increased austenite stability.

Optimizing the nitrogen (N) timings and rate can improve nutrient uptake, and nutrient-efficiencies, especially of N in wheat under the changing climate scenario. Climatic stress in the form of high temperature and drought resulted in the decreased crop physiology and, ultimately, grain yield. Taking the example of rainfed wheat, we quantified the impact of N application rates as full and split-dose at three variable sites of rainfed Pothwar, Pakistan by conducting field experiments for two years (2013-14 and 201-15). Treatments include, T₁ = Control (No fertilizer applied), full dose of N applied at the time of crop sowing, i.e. T₂ = 50 kg N ha^-1, T₃ = 100 kg N ha^-1 and T₄ = 150 kg N ha^-1 and split application of N at different timings during different stages of the crop called as split application of N, i.e. T₅: Application of 50 kg N ha^-1 (15 kg N ha^-1 (Sowing) : 20 kg N ha^-1 (Tillering) :15 kg N ha^-1 (Anthesis), T₆: Application of 100 kg N ha^-1 (30 kg N ha^-1 (Sowing): 40 kg N ha^-1 (Tillering) : 30 kg N ha^-1 (Anthesis) and T₇: Application of 150 kg N ha^-1(45 kg N ha^-1 (Sowing) : 60 kg N ha^-1 (Tillering) : 45 kg N ha^-1 (Anthesis). Three study sites include viz. Islamabad (High rainfall with optimum temperature), University Research Farm (URF)-Koont (Medium rainfall with moderate temperature), and Talagang (low rainfall with high temperature). Results showed that the highest stomatal conductance (0.80 mole m^-2 sec^-1), net photosynthetic rate (20.07 μmole m^-2s^-1), transpiration rate (9.58 mmole m^-2s^-1), intercellular CO₂ concentration (329.25 μmole CO₂ mol^-1 air), SPAD values (58.86 %) and proline contents (35.42 μg g^-1) were obtained for split application of N (T₆ = Split N₁₀₀) compared to control and full dose of N treatments. Among sites, these physiological traits remained highest at Islamabad and lowest at Talagang, while among years, maximum values of the measured parameters were obtained in 2013-14. A similar trend was observed for crop total N, N efficiencies, and agronomic traits of the crop. Our results suggest that optimum N application rate and its suitable timings can help to harvest real benefits of N as in our findings, split dose resulted in the maximum performance of the crop from physiological parameters to the agronomic traits of the rainfed wheat crop.

The photoreduction of CO2 is an intriguing process, which allows the synthesis of fuels and chemicals. One of the limitations for CO2 photoreduction in the liquid phase is its low solubility in water. This point has been here addressed by designing a fully innovative concept of pressurized photoreactor, allowing operation up to 20 bar and applied to improve the productivity of this very challenging process. The photoreduction of CO2 in the liquid phase was performed using commercial TiO2 (Evonink P25), TiO2 obtained by flame spray pyrolysis (FSP) and gold doped P25 (0.2 wt% Au-P25) in the presence of Na2SO3 as hole scavenger (HS). The different reaction parameters (catalyst concentration, pH and amount of HS) have been addressed. The products in liquid phase were formic acid and formaldehyde. Moreover, for longer reaction time and with total consumption of HS, gas phase products formed (H2 and CO) after accumulation of significant amount of organic compounds in the liquid phase, due to their consecutive photoreforming. Enhanced CO2 solubility in water was achieved by adding a base (pH= 12-14). In basic environment, CO2 formed carbonates which further reduced to formaldehyde and formic acid and consequently formed CO/CO2+H2 in the gas phase through photoreforming. The deposition of small Au nanoparticles (3-5 nm) (NPs) onto TiO2 was found to quantitatively influence the products distribution and increase the selectivity towards gas phase products.

In the present work, diamond films have been grown on GaN-on-Sapphire substrates by chemical vapor deposition (CVD) with the addition of nitrogen to the standard H2/CH4 precursor recipe. Diamond on GaN materials processing is not straight-forward, as GaN is susceptible to a quasi-pure hydrogen CVD plasma etching. 1%, 3% and 5% N2 gas was gradually added to the H2 gas with fixed 6% CH4 in the recipe to promote the growth of diamond nanocrystals. Different types of microstructures were produced, with addition of nitrogen to the precursor gas recipe. Nitrogen gas changes the diamond film microstructure from faceted to spherical grains, with signs of GaN etching. The sp3 bonded diamond film produced by nitrogen addition was found to be co-deposited along with a considerable amount of other non-diamond carbon phases (D - disordered graphite, G - crystalline graphite, TPA - trans-polyacetylene) and qualitatively all the diamond films were 50% pure (Raman peak ratio Isp3 / ID). The FWHM of the sp3 carbon Raman peak was calculated to be 6.5 cm-1, when there was no nitrogen gas in the precursor recipe, which deteriorates to a large extent after successive addition of N2. Fourier transform infrared spectroscopy (FTIR) showed a strong presence of the nitrogen related defects (peak positions at 1190 and 1299 cm-1) inside the nanocrystalline diamond (NCD) films grown with N2 addition. GaN layer etching from the base substrate by the CVD plasma was clearly evidenced by energy dispersive X-ray spectra (EDS) of the deposited films. Al elemental EDS peaks from the base sapphire substrate were observed for the films grown with nitrogen addition, but no Ga EDS peaks were detected. X-ray diffraction (XRD) micrographs further supported the enhanced GaN etching phenomenon. Nitrogen addition was thus found to be detrimental for growing CVD diamond films over GaN surfaces. The electrical resistivity of the uncoated GaN was initially measured to be 22.2 Ω-cm. However, the resistivity rose to 1.59×106 Ω-cm after the nitrogen assisted film deposition; due to the GaN etching - thereby exposing the underlying insulating sapphire substrate.

The cast defects strongly degrade the mechanical properties in cast alloys. The effect of Sn addition on Al-Si alloys was investigated by 3D computed tomography, SEM and TEM. Amorphous Sn oxides are found near the alumina film, cause more shrinkage pores, initiate cracks and deteriorate mechanical properties. This work suggests not adding Sn in various Al alloys used in cast state.

Additives can improve the efficiency of anaerobic digestion by increasing biogas production, reducing air pollution, and preventing total ammoniacal nitrogen (TAN) inhibition. Biological or chemical supplementation can also improve the economic efficiency of anaerobic digestion. However, the effects of specific additives on biogas production can vary depending on the type of supplement used. This research utilizes the additives on an industrial scale and monitors the optimization of the anaerobic digestion operating parameters after their addition. The various AD additives were examined in a sufficient cycle of operation for three biogas plants located in northern Greece. In this manner, the effectiveness was investigated in multiple initial feeds and unstable operating situations caused by the seasonality of specific feedstocks. The existing operation state in the three biogas plants was recorded before and after adding the supplements. In all three cases, lower concentration levels were observed in many of the examined trace elements. Introducing additives proved to be a stabilization factor in AD performance and inhibition mediator.

For order-of-addition experiments, the response is affected by the addition order of the experimental materials. Consequently, the main interest focuses on creating a predictive model and an optimal design for optimizing the response. Van Nostrand (1995) proposed the pairwise-order (PWO) model for detecting PWO effects. Under the PWO model, the full PWO design is optimal under various criteria but is often unaffordable because of the large run size. In this paper, we consider the D-, A- and M.S.-optimal fractional PWO designs. We first present some results on information matrices. Then, a flexible and efficient algorithm is given for generating these optimal PWO designs. Numerical simulation shows that the generated design has an appealing efficiency in comparison with the full PWO design, though with only a small fraction of runs. Several comparisons with existing designs illustrate that the generated designs achieve better efficiencies, and the best PWO designs and some selected 100% efficient PWO designs generated by the new algorithm are reported.

The process of shock wave focusing can make the strength of shock waves be continuously accumulated and turned into detonation wave in Pulse Detonation Engine (PDE). However, its effective application needs the inlet jets be in high temperature and velocity, which is difficult to be satisfied under certain conditions. Therefore, in this paper, metal magnesium assisted detonation initiation is proposed and the effect of magnesium particle addition on the shock wave focusing process in a kerosene-fueled PDE with cavity configuration is investigated through numerical simulation. The result showed that when the temperature of the premixed fuel/air jets injected in opposite direction was set as 650 K, the collision of leading shock waves on the central axis was the main source of energy deposition and the shock wave focusing could make the detonation be initiated in the cavity. When the temperature of jets is reduced to 550 K, fuel ignition and detonation could not be achieved through shock wave focusing. Then adding metal magnesium particles into the combustor made the energy deposition be enhanced and the detonation be induced. The diffusion of metal particles can significantly change the structure, motion, merging and dissipation of vortices in the flow field. Generally, the shock wave focusing process is basically not affected with metal particles injection. Therefore, this method can be successfully employed for detonation initiation in the cavity when the fuel/air premixed jet temperature is not high for PDE.

Thermoplastic molded regenerated silk was proposed as structural material in tissue engineering applications, mainly for application in bone. The protocol allows to obtain a compact non-porous material with a compression modulus in the order of a Giga Pascal starting from silk fibroin by compressing a silk fibroin lyophilized sponge of powder in mold at temperature higher than the glass transition temperature (Tg). The main purpose of the produced resin was the osteofixation and other structural applications in which the lack of porosity was not an issue. In this work, we introduced the use of citric acid in the thermoplastic molding protocol of SF to obtain a porosity inside the structural material. In addition to the previously developed protocols the addition of citric acid allowed us to obtain a structural material. The CA powder during the compression acted as a template for the pore formation. In addition, the CA was able to effectively crosslink the SF chain improving the mechanical strength. This effect was proved both evaluating the compression modulus and by studying the spectra obtained by Fourier infrared spectroscopy (FTIR). This protocol may be applied in the near future to the production of a structural bone scaffold.

Geopolymer is an emerging material alternative to Portland cement and has potential as a refractory material. Adding filler in geopolymer material is a strategy to increase the advantages of its physical and mechanical properties. It has been previously reported that adding nanoparticles can increase the compressive strength value, but there is no reported interaction between nanoparticles and geopolymer during the geopolymerization process. This study aims to study the effect of adding nano-zirconia fillers on the physical and mechanical changes of metakaolin-based geopolymers with nano-zirconia fillers. The geopolymer samples were made with 100 g of metakaolin as the base material and nano-zirconia in amounts of 2 gr, 5 gr, 10 gr, and 15 gr. Further characterization was carried out by XRD, FTIR, and SEM-EDX. This study showed that the compressive strength of the MZr05 sample increased significantly by 58.7% compared to the control sample. The test results of the structure and functional groups did not lead to any new compounds formed in the geopolymerization reaction. Therefore, the interaction of metakaolin geopolymer with nano-zirconia only creates an interfacial bonding.

We apply principles of Gibbs phase plane chemistry to and across the entire ocean-atmospheric interface. Surface tension increments support a two dimensional, tangential pressure well known to determine rates of bulk gas, bubble, salt, spray and momentum transfer plus both sensible and latent heat fluxes. Hence it is worth asking whether tension mapping follows from current understanding of two dimensional composition. A history is provided dating back centuries and demonstrating that detrital organic macromolecules are central; subtle surfactant functional variation creates a microforcing field which dissipates turbulent energy at the sub-meter scale. Since we have just distributed major biopolymeric classes emitted as primary organic aerosol, further climate links can be established by considering full planar thermochemistry. Organic microlayer behaviors are reviewed with attention to confined, analog phase transitions among two dimensional “solid, liquid, (and) gaseous” states serving as elasticity indicators. We also discuss surfactant properties of general marine dissolved organic carbon, demonstrating that only proteins and lipids are capable of occupying significant local micro-area. The literature often suggests albumin and stearic acid as best proxies, and so we distribute their concentrations through multilevel global ecodynamic simulations. Consensus distributions are obtained in order to control adsorptive equilibria. Working from conservation of planar free energy, a parametric equation of state is devised relating excess coverage to the surface pressure-modulus. Constant settings for the proxy pair are drawn from laboratory study, and they successfully reproduce frequencies for surfactant solid-to-gas occurrence in ambient compression experiments. Functionally resolved organic measurements are rare and so we group them into super-ecological province tables showing that our bulk concentration estimates are reasonable. Outputs are then fed into a coverage-tension-elasticity code. Resulting contours traverse the critical range for piston velocity, bubble-spray and damping effects on either a regional or seasonal basis. There is also a possibility for widespread microlayer crystallization in polar seas. The concepts are a direct extension of our organic aerosol work, and the two approaches could be inserted into Earth System Models in tandem. Uncertainties in the logic are enumerated and include kinetic and thermochemical factors at multiple scales. But the problems are reducible through molecular modeling coupled to renewed laboratory and field study. Connections to marine colloids-gels, microlayer iron chelation, and linings of the ice channel network are discussed additionally.

The development of good conductivity p-type β-Ga2O3 is critical to realize its devices and applications. The nitrogen-doped p-type β-Ga2O3 films with enhanced conductivity characteristics were prepared through the thermal oxidation of GaN in the N2O atmosphere. Further measurements were performed on the oxidized films at 1000, 1050, and 1100 °C to have insight into the underlying mechanism of the thermally activated transformation process. The room temperature photoluminescence (PL) spectra demonstrated a moderate ultraviolet emission peak at 246 nm, confirming the generation of gallium oxide with a band gap of ~5.0 eV. The normalized X-ray diffraction (XRD), the high-resolution transmission electron microscopy (HRTEM), and the selected area electron diffraction (SAED) patterns were used to confirm the characteristic of polycrystalline and anisotropic growth. Then, the effects of the oxidation temperature on the amount of incorporated nitrogen were analyzed using secondary ion mass spectrometry (SIMS). Moreover, the ionization energy of the acceptor of films oxidized at 1000, 1050, and 1100 °C was calculated and analyzed using the temperature-dependent Hall test results. The results showed that nitrogen doping was the main contributor to p-type electrical properties. The activation energy of the polycrystalline β-Ga2O3 prepared through thermal oxidation of GaN in the N2O atmosphere was estimated to be 147.175 kJ·mol-1 using the Arrhenius plot, which was considerably lower than that of both dry and wet oxidations of GaN in O2 ambient, thus confirming the efficiency of thermal oxidation of GaN in N2O.

This study investigates the effect of Re addition on the microstructure evolution and oxidation resistance of Co-Cr-Ta-Ti-C alloys. The alloys tested in this study consist of a Co-rich matrix with mixed HCP and FCC phases, together with TaTiC2 and Ti-based carbides. The addition of Re promotes the precipitation and growth of a CoCr-rich σ phase. Differential thermal analysis (DTA) showed that the melting temperatures did not change drastically up to 10 at% Re addition, whereas 15 at% Re addition significantly increased the melting temperature of the alloys. Oxidation tests in air at 1200°C showed that excessive Re content could lead to deterioration in oxidation resistance, mainly due to the accelerated formation of volatile Re oxides.

MoS2 lithium-based grease is suitable for lubrication protection between bearings at high temperatures and loads due to its excellent tribological properties. However, there is little research on the influence of different addition methods of MoS2 additive on the tribology and corrosion properties of lithium grease. In this work, vegetable oil with low toxicity, high biodegradation rate, and low cost was selected as the base oil, lithium 12-hydroxystearate as the thickener, and MoS2 as the additive. The effects of different adding modes of MoS2 on the tribology and corrosion properties of lithium grease were studied. The experimental results showed that adding 0.01wt% MoS2 before thickening was more conducive to improving the tribological properties of lithium grease. The average friction coefficient was 0.034, and the average spot diameter was reduced by 0.16mm. After grinding and adding 0.01wt% MoS2, the corrosion inhibition efficiency of the steel sheet was as high as 96.97%. The main reason was that the longer stirring and grinding were conducive to the uniform distribution of MoS2 in the grease, and the protective film formed by MoS2 and GCr15-bearing steel improved the lubrication performance and corrosion inhibition performance of the friction system.

: Sulfate presence is of great importance for anaerobic digestion as its addition can control the anaerobic microbial community. In this study, the effect of sulfuric acid addition on the perfor-mance of an UASB reactor fed with hydrolyzed starch was investigated. TOC, Fe and SO4-2 re-moval as well as the methane production were monitored under various COD/ SO4-2 ratios, HRTs and OLRs. When HRT was 16 hours and OLR equal to 2 g COD/LUASB-d the methane production was 0.24 L CH4/LUASB-day. After the sulfuric acid addition, TOC removal reached 95%. At HRT, OLR, and COD/ SO4-2 ratio equal to 16 hours, 2 g COD/ LUASB-d and 3.72 respectively, the methane production was 0.267 L CH4/LUASB-d. When the OLR was increased to 5.94 g COD/LUASB-d and COD/SO4-2 ratio was equal to 12.5, the methane production was 3 times higher (0.84 L CH4/LUASB-d) with a methane content in the produced biogas greater than 70%. 16s rRNA gene analysis demonstrated that after the sulfate addition, SRB were enriched and methane was mainly produced by Methanosaeta sp. This study indicates that appropriate sulfate concentrations in the feed in combination with the presence of iron in the UASB reactor lead to enhanced me-thane yields.

In the present work, a comparative evaluation of an MBBR unit performance was carried out for the following cases: when adding 3D-printed biocarriers fabricated with 13X and bentonite, when using K1 commercial biocarriers and when not adding biocarriers at all. For the evaluation of the MBBR efficiency, various physicochemical parameters were measured, while static light scattering and optical microscopy observations were additionally used. Finally, biofilm extracted from the biocarriers was evaluated. The findings suggest that there is an optimal biodegradation of the organic load in all MBBR units. The nitrification and denitrification process were improved at the 3D MBBR as compared to the control MBBR and MBBR K1. The dry mass of the biofilm in the 3D-printed biocarriers was two orders of magnitude larger than the one in the K1 biocarriers. What is more, in the K1 biocarriers the mass of the biofilm varied in relation to time, due to the fact that it could not be kept inside the holes, something that was not observed to happen with the 3D-printed biocarriers. Finally, it was observed, mostly in the 3D MBBR and less in the K1 MBBR, that the growth of nitrifying bacteria and heterotrophs inside the units increased the biomass production in the form of SMP, which in turn favored the adhesion of biomass on the surface of biocarriers.

Glutathione (GSH) and melatonin (MLT) are two antioxidants that have been described as having a protective role against oxidative stress in several animal species, improving sperm quality and survival after cryopreservation. Since there is no knowledge on the simultaneous use of these two substances concerning its effects on ram semen cryopreservation, this study aimed to evaluate the effects of MLT, GSH, or their association, on in vitro parameters of ram semen after thawing. During eight weekly sessions, the semen from three Merino rams was pooled, divided into four aliquots, and diluted with an egg yolk-based semen extender without (control) and with antioxidants (MLT 1mM, GSH 5mM, and MLT 1mM + GSH 5mM). Diluted semen was evaluated before and after freezing process. Supplementation of fresh semen with GSH at 5 mM had a deleterious effect on total motility progressive (TPM), curvilinear velocity (VCL), straight-line velocity (VSL), average-path velocity (VAP), linearity (LIN), straightness (STR) and increased slow spermatozoon (%). MLT at 1 mM also has a negative effect on TPM, VSL, and STR in fresh semen. In thawed semen, 1 mM of melatonin increased the TPM regarding the group control. Also, the combination of both antioxidants attenuates the negative effect of GSH 5mM on TPM, VSL and BCF. These results indicate that 5mM GSH impairs or does not improve sperm kinetic parameters in fresh semen and suggest that melatonin when combined with GSH plays a protective role on these effects.

Zn–Ni plating is indispensable in various industries because of its high corrosion resistance. However, Ni has been reported to trigger allergies; thus, an alternative Ni-free plating is desired. Zn–Fe plating is considered to be a promising candidate, albeit its corrosion resistance still needs to be improved. The corrosion resistance of Zn–Fe plating is expected to increase by the addition of Mo as the third alloying element as it is more noble than Zn and Fe. In this study, Zn–Fe–Mo plating with a corrosion resistance nearly equivalent to that of the Zn–Ni plating was fabricated. Zn–Fe–Mo plating was electrically deposited from continuously agitated plating baths prepared by mixing ZnSO₄, FeSO₄, Na₂MoO₄, Na₃C₆H₅O₇, and Na₂SO₄ using Fe or Ni plates as the substrate. The surface morphology, composition, crystal phase, and electronic state of Mo of the platings were investigated by SEM-EDS, XRD, and XPS. The anti-corrosion performance was evaluated by Tafel extrapolation method. Formation of plating comprising a Mo containing alloy phase was found to be crucial for improving corrosion resistance. The Zn–Fe–Mo plating demonstrates promise for replacing anti-corrosion Zn–Ni platings.

A construction for the systems of natural and real numbers is presented in Zermelo-Fraenkel Set Thoery, that allows for simple proofs of the properties of these systems, and practical and mathematical applications. A practical application is discussed, in the form of a Simple and Linear Fast Adder (Patent Pending). Applications to finite group theory and analysis are also presented. A method is illustrated for finding the automorphisms of any finite group $G$, which consists of defining a canonical block form for finite groups. Examples are given, to illustrate the procedure for finding all groups of $n$ elements along with their automorphisms. The canonical block form of the symmetry group $\Delta_4$ is provided along with its automorphisms. The construction of natural numbers is naturally generalized to provide a simple and sound construction of the continuum with order and addition properties, and where a real number is an infinite set of natural numbers. A basic outline of analysis is proposed with a fast derivative algorithm. Under this representation, a countable sequence of real numbers is represented by a single real number. Furthermore, an infinite $\infty\times\infty$ real-valued matrix is represented with a single real number. A real function is represented by a set of real numbers, and a countable sequence of real functions is also represented by a set of real numbers. In general, mathematical objects can be represented using the smallest possible data type and these representations are calculable. In the last section, mathematical objects of all types are well assigned to tree structures in a proposed type hierarchy.

The addition of flaxseed and amaranth on the physicochemical, functional and microstructural changes of instant-extruded cereals was evaluated. Six different mixtures were made with additions of amaranth (30%–50%) and flaxseed (10% and 15%) using maize grits and minor additives as supplementary ingredients and then extruded in a twin-screw extruder. The extrudates evaluated, had insoluble and soluble fiber contents increased with the proportion of amaranth and flaxseed. The mixture 4 (higher flaxseed content) presented highest soluble fiber percentage (1.9%). Extruded cereals had the lowest viscosity (<99.5 cp) and highest hardness values (5.2 N) whereas the dietary fiber content was highest. Fiber content increase, resulted in a higher water solubility index (WSI) (0.5) and decrease the water absorption index (WAI) (2.5). Amaranth and flaxseed incorporation increased crystallinity, resulting in a larger, and more compact laminar structure. Amaranth and flaxseed addition resulted in extruded cereals with acceptable physicochemical and functional properties.

Natural montane peatlands generally are not a significant source of nitrous oxide (N₂O) due to environment limitation including phosphorus (P) scarcity and temperature lowness. Phosphorus enrichment and warming caused by global change are altering this limitation, likely to increase the source function of N₂O. However, the combined effects of P addition and warming on N₂O fluxes and biotic/abiotic factor in peatlands are still uncertain. To address this, we investigated the long-term (12 yrs) effects of P addition (5 and 10 kg ha^-1 yr^-1) and its interaction with warming on N₂O fluxes in a peatland. The results showed that although long-term P addition did not significantly affect the source/sink function of N₂O in the peatland, it stimulated enzyme activities, promoted peat decomposition. However, warming amplified the effect of P addition to increase N₂O emissions by stimulating enzyme activities and changing soil stoichiometry, even turned the peatland into a significant source of N₂O with an emission of approximate 100 g m^-2 during the growing season. Our study suggests that P enrichment under the current background of global warming will enhance the possibility of strong N₂O emissions in montane peatlands, which may increase the risk to further aggravate global warming.

The variability observed in the annual seed production of perennial plants can be seen as an indication of changes in the allocation of resources between growth and reproduction, which can be attributed to fluctuations in the environment. However, a significant knowledge gap exists concerning the impacts of nitrogen addition on the interannual seed production patterns of perennial plant. We hypothesized that the addition of nitrogen would impact the annual variations in the seed production of perennial plants, ultimately affecting their overall reproductive efficiency. A multiyear field experiment was conducted to investigate the effects of varying nitrogen supply levels (e.g., 0, 4, 8 kg N ha−1 yr−1 of N0, N4, and N8) on the vegetative and floral traits, pollinator visitation rates, and seed traits over a period of four consecutive years. The results showed that the N0 treatment exhibited the highest levels of seed production and reproductive efficiency within the initial two years. In contrast, the N4 treatment displayed its highest level of performance in these metrics in the second and third years, whereas the N8 treatment showcased its most favorable outcomes in the third and fourth years. The similar patterns were found in the number of flowers per capitulum and the number of capitula per plant. There exists a positive correlation between aboveground biomass and several factors, encompassing the number of flowers per capitulum, the number of capitula per plant, the volume of nectar per capitulum, and the seed production per plant. This implies that the addition of N affected the maintenance of plant aboveground biomass, flower traits stability and, subsequently, the frequency of seed production, and the reproductive efficiency. Our results suggest that augmenting the nitrogen content in the soil may have the capacity to modify the inherent variability in seed production that is observed across various years. These findings have the potential to enhance our comprehension of the impact of nitrogen addition on the reproductive performance of perennial herbaceous plants, and the underlying mechanisms of biodiversity in the context of global environmental changes.

The method of micro-arc oxidation has been utilized to synthesize a protective biocompatible coating for a bioresorbable orthopedic Mg implant. This paper presents the results of a comprehensive research of micro-arc coatings based on diatomite – a biogenic material consisting of shells of diatom microalgae. The main focus of this study was the functionalization of diatomite-based micro-arc coatings by incorporating the particles of titania (TiO2) into them. Various properties of the resulting coatings were examined and evaluated. The XRD analysis has revealed the formation of a new magnesium orthosilicate phase – forsterite (Mg2SiO4). It has been established that the corrosion current density of the coatings has decreased by 2-4 orders of magnitude after the inclusion of TiO2 particles, depending on the coating process voltage. The adhesion strength of the coatings has increased following the particle incorporation. The processes of dissolution of both coated and uncoated samples in a sodium chloride solution were studied. The in vitro cell viability was assessed, which showed that the coatings significantly reduce the cytotoxicity of Mg samples.

Computational investigations on the BPE-ligated Cu-catalysed enantioselective addition of enynes to ketones were performed with DFT method. Two BPE-CuMes catalysts, BPE-CuMes and (S,S)-Ph-BPE–CuMes, were employed to probe the reaction mechanism with the emphasis on stereoselectivity. The calculations on the BPE-CuMes system indicate that the actvie metallized enyne intermediate acts as the catalyst for the catalytic cycle. The catalytic cycle involves two steps: 1) the ketone addition to the alkene moiety of the metallized enyne; 2) the metallization of enyne followed by the release of product with the recovery of the active metallized enyne intermediate. The first step accounts for the distribution of the products, and therefore is the stereo-controlling step in chiral systems. In the chiral (S,S)-Ph-BPE–CuMes system, the steric hindrance is vital for the distribution of products and responsible for the stereoselectivity of this reaction. The steric hindrance between the phenyl ring of the two substrates and groups at the chiral centers in the ligand skeleton is identified as the original of the stereoselectivity for the titled reaction.

Membrane distillation techniques appear as one of the most promise alternative to guarantee the availability of potable water in time of scarce of this essential resource. For membrane preparation, polyvinylidene fluoride (PVDF) is preferred due to the easier synthesis procedures with respect to other fluorine based polymers. In this work, copper oxide nanoparticles (CuONPs) at different weight percent (wt.%), embedded in PVDF membranes supported on non-woven polyester fabric (NWPET) were prepared by the phase-inversion method, and characterized by spectroscopy (ATR-FTIR, Raman) and electron microscopy techniques (SEM). The PVDF deposited onto the NWPET was highly composed by its polar -phase (F()= 53 %) which was determined from the ATR-FTIR spectrum. The F() value was kept constant, in the whole range of CuONPs studied (2-10 wt.%) as was determined from the ATR-FTIR spectrum. The absence of signals corresponding to CuONPs in the ATR-FTIR spectra and the appearance of peaks at 297, 360 and 630 cm-1 in the Raman spectra of the membranes suggested that the CuONPs are preferably located in the inner of the membrane but not on its surface. The membrane morphologies were characterized by SEM. From the obtained SEM micrographs, a decrease and increase in the amount of micropores and nanopores, respectively, near to the surface and intercalated in the finger-like layer were observed. As result of the CuONPs addition, the nanopores in the sponge-like layer decrease in size. The values of water contact angle (WCA) measurements showed a trend to decrease from 94° to 80° upon the addition of CuONPs (2-10 wt.%) indicating a diminish in the hydrophobicity degree of the membranes. Apparently, the increase in the amount of nanopores near to the surface decreased the membrane roughness becoming less hydrophobic.

The growth of plant and process of yield formation in crops are moderated by surrounding conditions as well as interaction of genetic background of plants and environment. In the last two decades significant changes in climate can be observed generating unfavorable and harmful impact on plant development. Drought stress can be considered as one of the most dangerous environmental factor influencing plant life cycle and decreasing production of biomass and finally the yield. Plants can react to water deficit in a wide degree what is dependent on the species, the genetic variability within the species, the phase of the plant ontogenesis, the intensity of stress, and other potential stress factors. In plants there can be observed hybrids between distinct taxa which exhibit certain traits adopted to tolerate stress conditions better than parental plants. Oat × maize addition (OMA) plants are good example of fertile hybrids with retained maize chromosomes as addition to complete oat genome. Hybrids generated via wide crossing can exhibit morphological, physiological and biochemical variations implemented by the occurrence of extra chromosomes of maize, as well as interaction of maize and oat chromatin. The molecular analysis indicated 12.5% OMA lines among all tested descendants of wide oat-maize crossing. On the fourteenth day of the drought, a significant effect of stress on the content of soluble sugars and phenolic compounds was observed, soil drought significantly reduced plant biomass above ground and several yield components. Less water lost revealed by results of the excised leaf water loss test was correlated with high yield of OMA lines. Phenolic compounds content might be used as biochemical indicator of plant drought tolerance since there were significant correlation with high kernel yields of plants subjected to drought stress.

Intensive development of many industries, including textile, paper or plastic, which consume large amounts of water and generate huge amounts of wastewaters containing toxic dyes, contribute to pollution of the aquatic environment. Among many known methods of wastewater treatment, adsorption techniques are considered as the most effective. In the present study the weakly basic anion exchangers such as Amberlyst A21, Amberlyst A23 and Amberlyst A24 of the polystyrene, phenol-formaldehyde and polyacrylic matrices were used for C.I. Direct Yellow 50 removal from aqueous solutions. The equilibrium adsorption data were well fitted to the Langmuir adsorption isotherm. Kinetic studies were described by the pseudo-second order model. The pseudo-second order rate constants were in the range of 0.0609-0.0128 g/mg·min for Amberlyst A24, 0.0038-0.0015 g/mg·min for Amberlyst A21 and 1.1945-0.0032 g/mg·min for Amberlyst A23, and decreased with the increasing initial concentration of dye from 100-500 mg/L, respectively. There were observed auxiliaries (Na2CO3, Na2SO4, anionic and non-ionic surfactants) impact on the dye uptake. The polyacrylic resin Amberlyst A24 can be promising sorbent for C.I. Direct Yellow 50 removal as it is able to uptake 666.5 mg/g of the dye compared to the phenol-formaldehyde Amberlyst A23 of the 284.3 mg/g capacity.

Successive-addition-of-digits-of-a-number(SADN) refers to the process of adding up the digits of an integer number until a single digit is obtained. Concept of SADN has been occasionally identified but seldom employed in extensive mathematical applications. This paper discusses SADN and its properties in terms of addition, subtraction and multiplication. Further, the paper applies the multiplication-property of SADN to understand the distribution of prime numbers. For this purpose the paper introduces three series of numbers -S1, S3 and S5 series- into which all odd numbers can be placed, depending on their SADN and the rationale of such classification. Extending the analysis the paper explains how composite numbers of the S1 and S5 series can be derived. Based on this discussion it concludes that even as the concept of SADN is rather simple in its formulation and appears as an obvious truism but a profound analysis of the properties of SADN in terms of fundamental mathematical functions reveals that SADN holds a noteworthy position in number theory and may have significant implications for unfolding complex mathematical questions like understanding the distribution of prime numbers and Goldbach-problem.

Titanium boride (TiB2) is a material classified as ultra-high temperature ceramics. The TiB2 structure is dominated by covalent bonds, which gives materials based on TiB2 very good mechanical and thermal properties, but also makes them difficult to sinter. Obtaining dense TiB2 polycrystals requires chemical or physical sintering activation. Carbon and molybdenum disilicide (MoSi2) were chosen as sintering activation additives. Three series of samples were made, the first with carbon additives: 0 to 4 wt.%; the second with 2.5, 5 and 10 wt.%. MoSi2 and the third with both additions of 2 wt.% carbon and 2.5, 5 and 10 wt.% MoSi2. MoSi2. On the basis of dilatometric sintering analysis, all additives were found to have a favourable effect on sinterability of TiB2, and it was determined that sintering of TiB2 with carbon addition can be carried at 2100°C and with MoSi2 and both additives at 1800°C. The polycrystals were sintered using the hot pressing technique. On the basis of the studies conducted in this work, it was found that addition of 1 wt.% of carbon allows to obtain single-phase TiB2 polycrystals of high density (>90%). The minimum MoSi2 addition required to obtain dense sinters with a cermet-like microstructure was 5 wt.%. High density was also achieved by materials containing both additives. Samples with higher MoSi2 content, i.e. 5 and 10% showed densities close to 100%. Mechanical properties such; as Young's modulus, hardness and fracture toughness (KIc) of the polycrystals and composites were similar for samples with densities exceeding 95%. The Vickers hardness was 23 to 27 GPa, the fracture toughness (KIC) was 4 to 6 MPa·m0.5 and the Young's modulus was 480 to 540 GPa. The resulting TiB2-based materials showed potential in high-temperature applications.

Virgin Argan Oil (VAO) is extracted from the fruits of the Moroccan endemic species argan [Argania spinosa (L.) Skeels]. It is known for its richness in polyunsaturated fatty acids and its unique composition in tocopherols conferring a panoply of pharmacological properties, documented in several studies. The aim of this study was to investigate the potential protective effect of VAO against oxidative and nitrosative stress induced in cells of the model species Tetrahymena pyriformis. As a comparison, well-known Virgin Olive Oil (VOO) from Olea europaea L. was used instead. Both oils were subjected to a preliminary analysis of phytochemicals and properties of interest. Oxidative stress in T. pyriformis cells was induced by hydrogen peroxide (H2O2) at 350µM, whereas sodium nitroprusside (SNP) nitrosative stress was induced using a 1mM concentration. Neither of these concentrations caused relevant changes in cell viability. The level of reactive oxygen species (ROS) was evaluated in the cell cultures by using H2-DCFDA dye. The activity and cell localization of the antioxidant enzymes catalase (CAT), superoxide dismutase (SOD) and glutathione peroxidase (GPX) was evaluated as well as the levels of glutathione (GSH) and the malondialdehyde (MDA) generated after lipid peroxidation. Finally, the presence and localization of intracellular lipid droplets was assessed by using Nile red. The treatment of cultures with H2O2 produced significant increases in the activity of CAT, SOD and GPX and in the level of GSH, as also did the SNP treatment. MDA level was increased by both the treatments. VAO and VOO treatment were found to protect T. pyriformis from oxidative stress and increased cells defense in nitrosative stress. In another hand VAO and VOO decreased significantly MDA level increased by H2O2 treatment and failed after SNP treatment. The quantification of fluorescence signal obtained from immunolocalization of antioxidant enzymes confirmed the results obtained after the evaluation of their activities. Interestingly the level of ROS and the number of lipid droplets increased by H2O2 treatment was significantly decreased by VAO and VOO co-treatments. VAO and VOO represent strong antioxidants, playing an important role in protecting cells against oxidative stress.

The extrusion of food for human and animal consumption is a unit operation that includes mixing, shearing and force to the materials related to the rheological properties of the materials in the extruder. The present work aims to study the rheological behavior of an extruded fish diet incorporating hydrolyzed protein flour processed by extrusion. The measurement was carried out online with a slit die rheometer, defining the rheological models and parameters that fit the process. During the extrusion process, the raw materials used were hydrolyzed protein meal, fish meal and cassava starch. For the results, the evaluated treatments were adjusted to the Power Law, where an increase in the shear rate decreases the viscosity of the material, corresponding to a pseudoplastic behavior. The incorporation of hydrolyzed protein flour presented a significant effect on the value of n and Klp, increasing the viscosity with the increase in the percentage of inclusion of HPH. The models obtained for the prediction of the viscosity are adjusted to the changes in shear rate, temperature and humidity of the system.

Melting, solidification and viscosity properties of a multicomponent Fe-Cu-Nb-Mo-Si-B alloys with low aluminum addition up to 0.42 at.% Al were studied using an oscillating cup viscometer. It is shown that melting and solidification are divided into two stages with a knee point at 1461 K. The temperature dependences of the liquid fraction between the liquidus and solidus temperatures during melting and solidification are calculated. It has been proven that aluminum accelerates the processes of melting and solidification and leads to an increase in liquidus and solidus temperatures. In the liquid state at temperatures above 1700 K in an alloy with a low aluminum content, the activation energy of viscous flow increases. This growth was associated with the liquid – liquid structure transition caused by the formation of large clusters based on the metastable Fe23B6 phase. Aluminum atoms attract iron and boron atoms and contribute to the formation of clusters based on the Fe2AlB2 phase and metastable phases of a higher order.

In this study, the effects of combined addition of CeLa and GdY on microstructure and mechanical properties of as-cast Al-4Cu-1Mn alloys were investigated by X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopies (TEM) and tensile testing. The results show that the minor addition of CeLa and GdY leads to the refinement of grain size. The addition of CeLa results in the formation of supersaturated vacancies in the Al matrix, whereas the addition of GdY leads to a decrease in the precipitation temperature of the Al2Cu phase. The combined CeLa and GdY addition can significantly increase ultimate tensile strength (UTS) while losing only a small amount of elongation (EL). Compared with the unmodified alloy, the grain size and SDAS of the alloy (0.2 wt% CeLa + 0.1 wt% GdY) were diminished by 67.2% and 58.7%, respectively, while maximum hardness and UTS rose by 31.2% and 36.9%, correspondingly.

The influence of the addition of 2.5, 5, 7.5, and 10.0% of dried Enoki and Maitake mushrooms on the content of bioactive compounds and some pro-health properties of pasta was studied. The qualitative and quantitative analysis of phenolic compounds performed using the LC-MS/MS technique indicated the highest amount of phenolic compounds in pasta supplemented with Maitake. However, all pasta enriched with Enoki mushrooms contained statistically significant-ly higher content of α-glucans in comparison to the control. In samples subjected to gastrointes-tinal digestion, the antioxidant, and potential anti-inflammatory activities were significantly higher than ethanolic and PBS extracts of samples. The ethanolic extracts from pasta fortified with dried Enoki and Maitake mushrooms had higher antioxidant activity (in some of the anti-radical and reducing power assays ) as well as a higher ability to inhibit lipoxygenase (E2.5 and E5 samples) compared to the control sample. Also some in vitro digested samples of pasta en-riched with dried Enoki and Maitake mushrooms showed higher chelating power (E10, M7.5 and M10); reducing power (E5, E7.5, and M10) and lipoxygenase inhibition (E7.5, E10 and M10) than the control. In conclusion, Enoki and Maitake mushrooms can be used for fortification of semo-lina pasta, conferring healthier characteristics of the product.

The welding performance of shipbuilding steel under large heat input could be improved greatly by the Mg addition to the steel, but the impact toughness of the HAZ is not stable. According to the three different thickness steel plates obtained in the industrial experiment, the large heat input welding was carried out by different heat input, and the impact toughness analysis, impact fracture analysis, metallographic microstructure analysis and inclusions analysis were carried out. The results showed that, the HAZ of three kinds of thickness plates induced a lot of IAF, with Mg addition, the inclusion dimension had been reduced effectively, and the IAF induced ability of the inclusions had also been improved. The difference of HAZ impact toughness with different welding heat input and different impact temperature is significant, in consideration of the influence of welding heat input and metallographic microstructure on impact toughness of HAZ, the welding heat load had far greater effect than metallographic microstructure on ductile-brittle transition temperature. At the same time, if the original metallographic microstructure of steel was coarse, the pinning effect of the inclusions would be reduced significantly, and the microstructure of HAZ would be coarsened and the impact toughness of HAZ would be decreased, so there is a certain matching relationship between the metallographic microstructure and the inclusion dimension.

A simple, effective and environmental-friendly method was adopted for enhancing the photocatalytic activity of g-C3N4 in the reduction of aqueous Cr(Ⅵ) under visible-light irradiation. The enhancement was achieved via treatment of g-C3N4 in organic solvent with addition of NaOH particles by ultrasonic process for two hours. The results demonstrated that the treated g-C3N4 exhibited much higher photocatalytic activity than pristine g-C3N4 in the reduction of Cr(VI) . Under visible light irradiation for 120 min, the reduced ratios of Cr(VI) with the initial concentration of 50 mg/L in the presence of the treated g-C3N4and pristine g-C3N4 were 100% and 37.1%, respectively. With the addition of fulvic acid, Cr(VI) was efficiently removed at 40 min. Based on the characterization results of the structures and other physiochemical properties of the treated g-C3N4 and pristine g-C3N4 by X-ray diffraction, scanning electron microscopy, transmission electron microscopy and UV Vis diffuse reflectance, the possible reasons responsible for the enhanced photocatalytic activity of the treated g-C3N4 were proposed. The yield and mechanism of different exfoliation methods were compared by semi-quantitative method.

Recently dairying becomes an important farming activity in the districts. Even if these districts are potential in milk production and marketing activities, little was known about determinates of participation and level of participation in milk value addition. This study was analyzing determinates of participation and level of participation in milk value addition in the study areas. Both primary and secondary data were used. Primary data were collected from 244 producers, 50 traders and 20 consumers by using semi-structured questionnaires. Data were analyzed by using descriptive statistics and econometrics model. Results from Heckman selection model first step revealed that milk producers’ participation decision on milk value addition was significantly affected by religion, distance the market, cooperative membership, volume of milk produced per day and market access. Whereas milk producers’ participation decision on the volume of milk value addition was significantly affected by religion, level of education, number of children less than six years, membership for milk cooperatives, volume of milk produced per day, access to market information, access to credit and access to livestock extension. Therefore, dairy sector development programs should take in to account determinants of participation decision on milk value addition as well as on volume of milk production.

The effect of Zr addition on the melting temperature of the CoCrFeMnNi High Entropy Alloy (HEA), known as the “Cantor’s Alloy”, is investigated, together with its microstructure, mechan-ical properties and thermo-mechanical recrystallization process. The base and Zr-modified al-loys are obtained by vacuum induction melting of mechanically pre-alloyed powders followed by recrystallization. The alloys were characterized by X-ray diffraction, scanning and transmis-sion electron microscopy, thermal analyses, mechanical spectroscopy and indentation measures. The main advantages of Zr addition are: 1) a fast vacuum induction melting (VIM) process; 2) the lower melting temperature, due to Zr eutectics formation with all the Cantor’s alloy elements; 3) the good chemical alloy homogeneity; 4) the mechanical properties improvement of recrystallized grains with a coherent structure. The crystallographic lattice of both alloys resulted to be FCC. Results demonstrate that the Zr-modified HEA presents a higher recrystallization temperature and smaller grain size after recrystallization with respect to the Cantor’s alloy, with precipita-tion of a coherent second phase which enhance the alloy hardness and strength, while maintaining a good tensile ductility.

Novel 1,2,3-triazole compounds 3–4 were synthesised via the regioselective addition and cyclization reaction of 1,1-enediamines (EDAMs) 1 with p-methylbenzenesulfonyl azide (TsN₃) 2 in 1,4-dioxane at refluxing for 5 hours. As a result, 1,2,3-triazoles 3–4 can be easily and efficiently obtained via catalyst-free click chemistry. The reactions have some advantages such as metal-free catalyst, excellent yield, inexpensive raw materials, and convenient final treatment.

Semi-solid feedstock of AZ80 magnesium alloy modified by minor rare-earth Y element (0, 0.2, 0.4, 0.8 wt.%) were fabricated by strain induces melting activated (SIMA) in the form of extrusion and partial remelting. The effect of Y addition on the microstructure evolution of extruded and isothermal treated alloy was observed by optical microscope (OM), scanning electron microscope (SEM), X-ray diffraction (XRD) and quantitative analysis. The results show that the Y addition can refine the microstructure and make the β-Mg17Al12 phases agglomerating. During the subsequent isothermal treatment at 570℃, the average solid grain size, shape factor and liquid fractions increased with prolonged soaking time. Smaller spheroidal solid grains and the larger shape factor were obtained due to Y addition. The coalescence and Ostwald ripening of solid grains operated the coarsening process simultaneously. The coarsening rate constants of AZ80M1 (0.2 wt.% Y addition) of 164.22 μm3s-1 was approximately four times less than the un-modified AZ80 alloy of 689.44 μm3s-1. In contrast, the desirable semi-solid structure featured by fine, well globular solid grains and appropriate liquid fractions and shape factor was achieved in AZ80M1 alloy treated at 570℃ for 20-30 min.

Statement of problem: Henna has been added to polymethylmethacrylate (PMMA) as a new type of antifungal agent; however, its effect on the latter’s physical properties has not been investigated. Purpose: This study aimed to evaluate the effect of the addition of various henna concentrations on the surface roughness and hardness of PMMA denture base material. Materials and Methods: A total of 99 specimens of rectangular-shaped (10×20×3 mm3) acrylic specimens were prepared from heat-cured acrylic resin. Specimens were divided into one control group without the addition of henna and five test groups, which were prepared by adding Yamani henna powder to acrylic powder at concentrations of 1wt%, 2.5wt%, 5wt%, 7.5wt%, and 10wt%. The polymer was added to the monomer before being mixed, packed, and processed using the conventional water bath method. After processing, specimens were finished and polished, then kept in distilled water for 48+2 h. A profilometer and Vickers hardness tester were used to measure surface roughness and hardness respectively. Statistical data analysis was conducted via SPSS version 20.0 (IBM, USA). Results: The addition of henna at varying concentrations significantly increased surface roughness values (P ≤ 0.01) while decreasing hardness (P ≤ 0.0001). The most favorable addition value was 1% henna between all henna groups. Conclusion: The addition of henna to the acrylic resin may negatively affect the surface properties of PMMA acrylic denture base.

For successful reuse of old asphalt as reclaimed asphalt pavement (RAP) added to new bituminous mixtures it is necessary to improve some of its properties. This can be attained, for example, by adding an appropriate rejuvenating agent. The aim of this study was to evaluate the properties of a lab aged 35/50 pen grade bitumen, rejuvenated by addition of two varieties of rapeseed imidazo-line. Both short-term and long-term ageing were simulated using the Rolling Thin Film Oven Test (RTFOT) and Pressure Ageing Vessel (PAV), i.e. standard lab ageing methods. The first step in-cluded determination of the basic properties of the analysed pen grade bitumen. Fatigue cracking resistance of the bitumen was checked as the next step. The dynamic shear rheometer (DSR) test was carried out for this purpose, at the intermediate operating temperature of road pavements. The obtained data were then used to calculate the fatigue cracking critical temperature (FCCT). A ductility test was also carried out in a ductilometer, in which the applied tensile force was meas-ured. The obtained results demonstrated a beneficial effect of rapeseed imidazoline on the prop-erties of the tested pen grade bitumen after ageing, when added at a rate of 6% and more.

The process of anaerobic digestion used for methane production can be enhanced by incorporating stimulating materials. The effects of these materials are dependent on various factors including the processed substrate, process conditions, and the type and amount of the stimulating material used. As part of the study, three different stimulating materials - iron powder, lime, and milled porous ceramic - were added to the 30-day anaerobic digestion of the brewer's spent grain to improve its performance. Different doses ranging from 0.2 to 2.3 gTS×L-1 were tested, and methane production kinetics were determined using the first-order model. The results showed that the methane yield ranged from 281.4±8.0 to 326.1±9.3 ml×gVS-1, while substrate biodegradation ranged from 56.0±1.6 to 68.1±0.7%. The addition of lime reduced methane yield at almost all doses by -6.7% to -3.3%, while the addition of iron powder increased methane yield from 0.8% to 9.8%. The addition of ceramic powder resulted in a methane yield change ranging from -2.6% to 4.6%. These findings suggest that the use of stimulating materials should be approached with caution, as even slight changes in the amount used can impact methane production.

Polypropylene (PP) foam has a great deal of application since it normally exhibits non-uniform cell size distribution, low cell density, and cracked cells. In this study, a small amount of fluoroelastomer (FKM) was used as a nucleating agent to prepare well-defined microporous PP foam by supercritical CO₂. It was observed that solid FKM was present as the nanoscale independent phase in PP matrix and the FKM could induce a mass of CO₂ aggregation, which significantly enhanced the diffusion rate of CO₂ in PP. The resultant PP/FKM foams exhibited much smaller cell size (～24 μm), and more than 16 times cell density (3.2×10⁸ cells/cm³) as well as a much more uniform cell size distribution than that of the neat PP foam. PP/FKM foams possessed major concurrent enhancement in their tensile stress and compressive stress compared to neat PP foam. We believed that the added FKM played a key role in enhancing the heterogeneous nucleation, combined with the local strain field variation in the multiple-phase system, which was responsible for the considerably improved cell morphology of PP foaming. This paper provides a deep understanding of the scCO₂ foaming behavior of PP in the presence of FKM.

The pressing process and density profile of particleboards produced with addition of waste wood containing phenol-formaldehyde (PF) resin was presented. The particles were melamine-urea-phenol-formaldehyde (MUPF) resinated. Recovered particles were obtained from post-industrial waste plywood. The press closing time recorded during the pressing of mats containing only recovered particles in the core layer (100%), at a unit pressure of 3 MPa, in which the face layer rate was 50%, resin load for face and core layer was 12% and 10% was shorter by 29% than for the industrial particle mats. Regardless of the level of variability of independent factors the overheating time of mats to a temperature of 100 °C, containing recovered particles was 10% - 20% shorter than the time of overheating mats with industrial particles. The greatest impact (52%) on maximum density of the face layer of particleboards was demonstrated by the content of the recovered particles and the resin load (32%). The maximum density area of the face layer was located closer to the surface in particleboards produced with a higher (80%, 100%) content of the recovered particles, a higher (i.e. 12% and 10%, respectively, for face and core layer) resin load, a lower (35%) face layer rate and a higher (3 MPa ) unit pressure.

In order to address the issue of nutrient deficiency in coconut coir-based nursery substrates, three materials with nutrient supplementation effects, namely pig manure, composted rice husks, and agricultural humic acid, were added in equal volumes to the coir-based substrate. The newly formulated substrates were then tested for their seedling growth effects on cucumber and rice. Results indicate that the substrate formulation consisting of "10% pig manure + 30% peat + 50% coconut coir + 10% vermiculite" was capable of satisfying the growth requirements of both cucumber and rice seedlings, with the highest acceptance among farmers.

The objective of this study was to evaluate the effect of the addition of a phytogenic compounds blend (PHA) containing hydrolyzable tannins, carvacrol and cinnamaldehyde oil in the mineral salt or energy supplement on the rumen microbiota and nitrogen metabolism of grazing Nellore cattle. Eight castrated Nellore steers were distributed in a double Latin square 4 × 4 design, with a 2 × 2 factorial arrangement (two type supplements and the addition or not of PHA) as follows: energy supplement without PHA addition (EW); energy supplement with PHA addition (EPHA); mineral supplement without the addition of PHA (MW); and mineral supplement with PHA addition (MPHA). Steers that received supplements with PHA have a lower ruminal proportion of Valerate (with PHA 1.06%; without PHA 1.15%), a lower ruminal abundance of Verrucomicrobia and a tendency for lower DM digestibility (with PHA 62.8%; without PHA 64.8%). Energy supplements allowed higher ammonia concentrations (+2.28 mg of NH3-N/dL), increased the propionate proportion (+0.29% of total VFA), and showed a tendency to have a higher abundance of Bacteroidetes and a lower abundance of Firmicutes in the rumen. The PHA addition in the supplement did not improve the use of nitrogen in grazing cattle, but negatively affected the diet digestibility.

The principal main of this research work was the study the influence of Cu addition on the wear behavior (WB) of eutectic Al-12.6Si alloy developed by spray forming (SF) method and compared with as-cast (AC) alloys. The phases of chemical compositions and microstructure were studied by optical microscopy, energy dispersive spectroscopy (EDS) and Scanning Electron Microscopy (SEM). The microstructure of SFAl-12.6Si (SF1) alloy reside — of fine primary and eutectic Si phases evenly distributed in the equiaxed α-Al matrix and SF Al-12.6Si-2Cu (SF2) alloy lie of uniformly distributed fine eutectic Si particulates and spherical form θ-Al2Cu precipitates in α-Al matrix. On other hand, the AC Al-12.6Si alloy (AC1) alloy involve of eutectic Si needles in the dendrite α-Al matrix, whereas AC Al-12.6Si-2Cu (AC2) alloy consisted of eutectic Si needles and Chinese script form θ phase distributed randomly in the α-Al matrix. The microhardness and wear properties were analyzed using Vickers hardness (VH) and dry sliding WT. The SF alloys exhibit superior hardness compared to the AC alloys. The wear properties of SF alloys exhibited significantly superior compared to the AC alloys. The SF2 alloy showed high wear resistance (WR) than the SF1 alloy in the entire sliding velocities and applied loads. The results indicate that the spray deposited alloys have a lower coefficient of friction (CF(µ)) than the AC alloys under varying load and sliding velocity conditions. The high WR in the SF alloy was due to microstructural modification during SF and precipitation of fine Al2Cu intermetallic and solid solubility effects. The SF2 depicts increased transition from oxidative to abrasive. In other ways, AC alloys demonstrate wear mechanisms that change from oxidative to abrasive and delamination with an increase in sliding velocity and load.

The present work analyzes the behavior in terms of corrosion resistance of three reinforced concrete formulations over a period of 1 year. The samples were accompanied by creating a monitoring methodology using the Electrochemical Impedance Spectroscopy (EIE) technique, working only with the real component over time. Three mixtures were used, one conventional without pozzolanic addition (REF) and two others with pozzolanic additions, rice husk ash (RCA) and metakaolin (MK). Prototypes were created and exposed to the action of a 165g/l NaCl sodium chloride solution. The characterization of the materials was carried out by determining the chloride diffusion profile (ASTM 1556), analyzing images using tomography and with the support of analytical techniques such as x-ray fluorescence and x-ray diffraction. The monitoring methodology using the EIE demonstrated the positive effect of the insertion of pozzolans, rice husk ash (RCA) and metakaolin (MK), by delaying the process of chloride diffusion in the concrete, resulting in greater resistance to corrosion. The EIE also showed that the active mineral addition in concrete, of aluminum-silicic composition (MK), had a predominant protective effect on the steel//concrete interface against the attack of chloride ions.

Biphasic bone substitutes (BBS) are nowadays established biomaterials. Through their constant development even natural components like hyaluronic acid (HY) are added to improve both their handling and also their regenerative properties. However, low knowledge exists regarding the consequences of the HY addition for their biocompatibility and the inflammatory tissue reactions. Thus, the present study was conducted aiming to analyze the influence of two different amounts of high molecular weight HY (HMWHY) combined with a BBS on the in vitro biocompatibility and the in vivo tissue reaction. Established in vitro procedures using L929 cells were used for cytocompatibility analyses under the test conditions of DIN EN:ISO 10993-5. For the in vivo study part, calvarial defects were created in 20 Wistar rats and subsequently filled with the BBS and the BBS combined with two different HMWHY amounts, i.e., BBS+HY(L) and BBS+HY(H). As controls empty defects were used. Established histological, immunohistochemical and histomorphometrical methods were applied to analyze the tissue reactions to the three different materials, including the induction of pro- and anti-inflammatory macrophages and multinucleated giant cells (BMGCs). The in vitro results showed that none of the materials or compositions caused biological damages to the L929 cells and can considered to be non-toxic. The in vivo results showed that only the addition of high doses of HY to a biphasic bone substitute significantly decreases the occurrence of proinflammatory macrophages (* p < 0.05) comparable to the numbers found in the control group, while no significant differences within the three study groups for M2-macrophages nor BMGCs were detected. In conclusion, the addition of different amounts of HMWHY does not seem to affect the inflammation response to the BBS while improving the material handling properties.

The development of analog rice, apart from being an effort to diversify food, also has the potential to be develop as functional food in fulfilling the nutrients needed by a community. Katuk leaf is known for its ability to accelerate breast milk production for lactating women which is inseparable from sterol as bioactive content. This study aimed to determine the best formulation of analog rice made from cassava flour, banana flour, Katuk leaf powder and soy lecithin that was sensory acceptable, in a shape resembling rice, and able to fulfill the nutritional needs of lactating women. Analog rice was produced using extruder machine before the physical and sensory properties analyses were carried out, followed by the chemical properties analysis. Formulation C (80% cassava flour, 20% banana flour, 3% Katuk leaf powder and 0.5% soy lecithin) was obtained as the best or most preferred formulation based on sensory analysis which the grain shaped oval round resembling original rice and had green-brownish color, fluffy texture, distinct aroma and taste derived from the raw material used. Therefore, this research is expected to support the development of analog rice for providing the main staple food for fulfilling the lactating women’s nutrition.

The overwhelming evidence supports the assertion that the climate is undergoing change. Understanding the perception of locals of the magnitude of climate change and its influence on non-timber forest products (NTFPs) challenge at a global scale. Although studies on climate change, value addition, and the multiple uses of NTFPs and their impact on local livelihoods have been conducted, locals' perceptions of these factors have not been fully explored. This study aims to assess various social factors, including education, gender, and religion, and their influence on locals' perceptions of the abovementioned factors. The research focused on five regions where NTFPs are prevalent in Ghana (Western North, Bono, Ahafo, Ashanti, and Eastern regions). To investigate the impact of social factors on local perceptions of climate change, value addition, and the multiple values of NTFPs within rural communities, a total of 732 interviews with a team of interviewers across these five regions in Ghana were carried out. We applied a logistic regression model to assess the social factors and their influencing locals’ perceptions of the mentioned variables. It was revealed that age, gender, education, and occupation did not significantly influence locals' perceptions of climate change. However, religion was found to influence locals' perceptions of climate change. Furthermore, the results demonstrated that gender (P<0.000328) and education (P<0.00426) strongly influenced locals' perceptions of value addition to NTFPs. In contrast, religion and constraints (related to time, finance, and skills) did not significantly influence locals' perceptions. Additionally, it was observed that gender (0.00132), education (0.00692), and religion (8.12e-05) significantly influenced how locals perceive and use NTFPs. In conclusion, this study provides valuable insights into the intricate interplay among local perceptions, climate change, value addition, multiple uses of NTFPs, and the capacity of NTFPs to enhance the well-being of forest fringe communities. These findings underscore the importance of comprehensive, tailor-made interventions that consider local perspectives and adhere to sustainable approaches, with the aim of optimising the positive impacts of NTFPs in poverty alleviation and overall community development.

Soil enzyme activity can be affected by both production and degradation, as enzymes can be degraded by proteases. However, the impact of nutrient addition on enzyme activity is often solely attributed to changes in enzyme production without fully considering degradation. Here, we demonstrated that the activities of β-1,4-glucosidase (BG), β-D-cellobiohydrolase (CBH), β-1,4-Xylosidase (BX), and β-1,4-N-acetyl-glucosaminnidase (NAG) were comparable in nitrogen (N) and phosphorus (P) fertilized soils and the unfertilized control under field conditions, but the reduction in activity was substantially greater in the fertilized soils during short-term laboratory incubation. The results show that the interruption of the natural, continuous supply of organic matter or non-soil microbial-derived enzymes, which typically occurs under field conditions, leads to a more significant reduction in apparent enzyme activities in fertilized soils compared to unfertilized control. This may be attributed to the higher abundance of protease in fertilized soils, resulting in faster enzyme degradation. Interestingly, P fertilization alone did not have a similar effect, indicating that N fertilization is likely the main cause of the larger decreases in enzyme activity during incubation in fertilized soils compared to unfertilized control soils, despite our study site being poor in P and rich in N. These findings highlight the importance of considering enzyme degradation when investigating material dynamics in forest ecosystems, including the impact of nutrient addition on enzyme activity, as enzyme production alone may not fully explain changes in apparent enzyme activity.

This study was carried out to determine the effects of apple vinegar and sodium diacetate addition on the aerobic stability of fermented high moisture maize grain (HMM) silage after opening. In the study, the effect of three different levels (0, 0.5, 1.0%) of apple vinegar (AV) and sodium diacetate (SDA) supplementation to fermented HMM at two different storage conditions (27-29°C, 48% Humidity; 35-37°C, 26% Humidity) were investigated. The material of the study was fermented rolled maize grain with 62% moisture content stored for about 120 days. Silage samples were subjected to aerobic stability test with 3 replicates for each treatment group. Wendee and microbiological analyses were made at 0, 2, 4, 7, and 12 days. Meanwhile, samples were displayed in the T200 IR brand thermal camera. According to the thermogram results, 1% SDA addition positively affected HMM silages at the second and fourth days of aerobic stability at both storage conditions (p<0.05). Aerobic stability and infrared thermography analysis indicated that 1% AV, 0.5%, and 1% SDA additions to HMM silages had promising effects. Due to our results, we concluded that thermal camera images might be used as an alternative quality indicator for silages in laboratory conditions.

Bone cement, mainly based in PMMA, is commonly used in different arthroplasty surgical proce-dures, and its use is essential for prosthesis fixation. However, its manufacturing process reaches high temperatures that can produce necrosis in the patients' surrounding tissues. In order to con-tribute to avoid this problem, the addition of graphene could delay the polymerisation of the MMA and, simultaneously, contribute to the optimisation of the composite material's properties. This article analysed the effect of the addition of different percentages of Highly Reduced Graphene Oxide (HRGO) with different wt. % (0,10, 0,50 and 1,00) and surface densities (150, 300, 500 and 750 m2/g) on the physical, mechanical, and thermal properties of commercial PMMA-based bone cement and its processing. It was noticed that a lower sintering temperature would be reached with this addition, making it less harmful to use in surgery and as it reduces its adverse effects. In contrast, the materials' density does not show significant changes, which indicates that the addi-tion of HRGO does not significantly increase its porosity. Lastly, the mechanical properties are re-duced by almost 20 %. Nevertheless, these properties are high enough so that these new materials can still fulfil their structural function.

Abstract: Interactions in multicomponent Ni-Cr-Mo-Al-Re model alloy were determined by ab initio calculations in order to investigate the Re doping effect on Haynes 282 alloy. Simulation results provided an understanding of short-range interactions in the alloy and successfully pre-dicted the formation of a Cr and Re-rich phase. The Haynes 282 + 3 % wt. Re alloy was manu-factured using the additive manufacturing Direct Metal Laser Sintering (DMLS) technique, in which the presence of the (Cr17Re6)C6 carbide was confirmed by an XRD study. The results ob-tained provide useful information about the interactions between Ni, Cr, Mo, Al, and Re as a function of temperature. The 5-element model designed can lead to a better understanding of phenomena that occur during the manufacturing or heat treatment of modern, complex, multi-component Ni-based superalloys.

Plants do need a fixed proportion of carbon (C), nitrogen (N) and phosphorus (P) elements to maintain normal metabolic activities. The P fertilizers are widely used to supplement nutrients in subtropical plantations. Stoichiometric homeostasis reflects the strategy of plants to cope with various environments (including P fertilizer supply rate). It is thus of great significance to understand C:N:P stoichiometry in the plant-litter-soil system under P addition and stoichiometric homeostasis of plant tissues for fertilization management of slash pine (Pinus elliottii Engelm) plantations. We measured the C, N and P contents in root, branch, needle, litter and soil in slash pine plantations fertilized with four treatments - P1 (25 kg P ha−1 yr−1), P2 (50 kg P ha−1 yr−1), P3 (100 kg P ha−1 yr−1), and a control (CK) in subtropical China and calculated stoichiometric homeostasis of plant tissues. Results showed that P addition increased the capacity of needle to obtain C, N and P elements and altered the C:N:P stoichiometry of plant tissues, as well promoted the accumulation of C and P elements in soil, but had no significant effect on soil stoichiometry. The nutrient contents of needle and branch were higher than those of root and litter, indicating that slash pine was more inclined to allocate nutrient to the aboveground tissues. The stoichiometric homeostasis of C, N and P among plant tissues was ranked as follows: root > branch > needle, and homeostasis of nutrient elements in the needle was C > N > P. This indicated that the C, N and P stoichiometric homeostasis was various among plant tissues and elements types under P addition. These findings suggest P addition would alleviate the P limitation of slash pine growth in subtropical regions. In the future, long-term observation experiments should be conducted and the trade-off between P addition rates and economic and ecological benefits should be considered.

Methane fermentation of organic waste is one way to minimize organic waste, which accounts for 77% of the global municipal waste stream. The use of biowaste treatment technologies helps to improve the energy independence of the regions. Improving the efficiency of the methane fermentation process by using additives from waste may be an attractive alternative to the original technology. The use of biochar as an additive for methane fermentation has been shown to increase the production potential of biogas. The reasons for the improvement in efficiency are complex among others, it is assumed that the specific surface area of ​​biochar may increase the population of anaerobic organisms. Up to date, there are many researches on the effect of biochar additions on methane fermentation, but there is no research on the effect of sulfur-biochar composite. The composite product in the form of a mixture of biochar and molten sulfur is an interesting area of ​​research. In this experiment additions of the sulfur-biochar composite were tested to improve the fermentation process. The composite consisted of 40% biochar and 60% of sulfur and was added to the process. As results the addition of 1% of the composite increased the biogas potential by 4%.

The influence of the Fe2O3 addition amount on the dephosphorization of hot metal at 1623 K with the slag of the low basicity (CaO/SiO2) of about 1.5 was investigated by using high-temperature laboratorial experiments. With increasing the Fe2O3 addition amount, the contents of [C], [Si], [Mn] and [P] in hot metal at the end of dephosphorization decrease, and the corresponding removal ratios increase. The P2O5 content in slag increases, and the CaO and SiO2 contents in slag decrease. The phosphorus mainly exists in the form of the nCa2SiO4-Ca3(PO4)2 solid solution in the phosphorus-rich phase and the value of coefficient n decreases from 20 to 1 with increasing the Fe2O3 addition amount from 5 g to 30 g. With increasing the Fe2O3 addition amount, the oxygen potential and activity at the interface between the slag and hot metal increase. When the oxygen potential and the oxygen activity at the interface are greater than 0.72×10-12 and 7.1×10-3, respectively, the dephosphorization ratio begins to increase rapidly. With increasing the Fe2O3 addition amount to 30 g, the ratio of the Fe2O3 addition amount to theoretical calculation consumption is around 175%, and the dephosphorization ratio reaches the highest value of 83.3%.

The effects of co-addition CeO2 and SiC particles on the morphology, surface cracks, microstructure, precipitated phases and wear property of plasma beam spraying Fe55-based coatings on 1025 steel were investigated by optical microscopy (OM), scanning electron microscopy (SEM), energy-dispersive X-ray spectrometer (EDS), ultra-deep field microscope and wet sand rubber wheel friction tester, respectively. The results showed that the dendrite exhibited a directional growth pattern perpendicular to the substrate and the transitional states of microstructure with the co-addition CeO2 and SiC particles. With addition of CeO2 or SiC affected the flowability of molten steel at macro level, leading to a reduction in the liquid phase diffusion coefficient DL of Cr and C and resulted in a decrease in the G/R ratio. The dendrites changed into equiaxed grains. The main phase composition of Fe55 welding layer is Cr7C3, γ-Fe. The grain boundaries consisted mainly of a reticular eutectic structure. The worn-out uniformly surface of the Fe55+1.5 wt% SiC+0.01wt% CeO2 with Ra was 0.28 μm was smoother than that of other samples. The sub-wear mechanisms during the friction process were microploughing and microcutting. The hardness and toughness of Fe55+1.5 wt% SiC+0.01wt% CeO2 were well-matched, avoiding excessive microcutting and microplastic deformation.

This study was conducted to determine the effect of different types of olive cake (five treatments) in the diet of Bísaro pigs on the volatile compounds and sensory characteristics in the dry-cured loin and dry-cured “cachaço” (2 processed meat products). The treatments applied are based on the type of extraction and this may imply differences in their water and fat content. Eighty com-pounds were identified, and grouped into eight chemical classes: hydrocarbons, aldehydes, es-ters, alcohols, ketones, acids, furans, and other compounds. Aldehydes and alcohols were the ma-jor groups of compounds, representing 57.06-66.07 % and 68.67-75.61 % for the loin and “cacha-ço”, respectively. There were no significant differences between treatments for any of the volatile compounds identified. The major aldehydes were hexanal, heptanal, pentanal, and propanal. These compounds were significantly higher (p<0.001) in “cachaço”. This significant difference be-tween the two types of dry-cured products is directly related to the amount of total fat content. The major alcohols were 2.3-butanediol, 1-octen-3-ol, 1-butanol, 3-methyl, 1-hexanol, benzyl-alcohol and glycidol. Except for compounds 2,3-butanediol and benzyl-alcohol, the majority in this group are significantly different in terms of the type of dry-cured product. As for the sensory evaluation, for both dry-cured products, the trained tasters did not detect significant differences between the different treatments, which is in line with the results obtained for volatile compounds.

The aim of the experiment was to determine the effect of strontium oxide addition on zirconium silicate recrystallization when adding strontium oxide to the glaze composition. Zirconia glazes (4 different contents) were prepared to which strontium oxide was added in amounts of 0, 1, 3, 6, and 12 mass%. SrO. The characteristic temperatures of the raw glazes were measured, based on which the maximum firing temperatures were determined. The fired glazes were subjected to study of the phase composition and observation of the microstructure. Analysis of the characteristic temperatures showed a fluxing effect, but it was not as strong for all glazes. Differences in the amount of the crystalline phase of zirconium silicate obtained in fired glazes and the partial transition of zirconium silicate to the amorphous phase were observed. Observations of the microstructure clearly indicated an increase in the homogeneity of the distribution of zirconium silicate.

Is there any possible synergic effect of fertility outcome between spindle view-assisted intracyto-plasmic sperm injection (SV-ICSI) with or without assisted oocyte activation (AOA) for patients with low fertilization rate history? To explore the answer, a retrospective study was held in our fertility center by reviewing patients receiving SV-ICSI during 2019/03 to 2023/06. Total 47 pa-tients were included, the fertility outcomes of intervention group (AOA-SV-ICSI, 14 patients) and control group (SV-ICSI, 33 patients), such as fertilization rate, blastocyst formation rate and clin-ical pregnancy rate, were analyzed. The blastocyst formation rate between groups was signifi-cantly higher in AOA-SV-ICSI group (p=0.020), but the fertilization rate and clinical pregnancy rate did not reach any statistical significance. This discovery of increased blastocyst formation rate in low fertilization rate patients could possibly help them in getting more usable embryos in fertility treatment.

A bread wheat line (N11) and a disomic 2D(2R) substitution triticale line have been crossed and backrossed four times. At each step electrophoretic selection for the seeds that possessed, simultaneously, the complete set of high molecular weight glutenin subunits of N11 and the two high molecular weight secalins of rye, present in the 2D(2R) line, was carried out. Molecular cytogenetic analyses of the BC4F5 generation have revealed that the selection carried out had produced a disomic addition line (2n=44). The pair of additional chromosomes consisted of the long arm of chromosome 1R (1RL) from rye fused with the satellite body of the wheat chromosome 6B. Rheological analyses revealed that the dough obtained by the new addition line had higher quality characteristics when compared with the two parents. The role of the two additional high molecular weight secalins, present in the disomic addition line, in influencing improved dough characteristics is discussed.

Milk serves as a crucial source of natural bioactive compounds essential for human nutrition and health. The gastrointestinal digestion of milk proteins releases various biologically active peptides that positively impact human health and enhance physiological performance. With the growing production of cheese, Greek yogurt, and other dairy products, the volume of unutilized acid whey is significantly increasing. Acid whey, containing almost all whey proteins and approximately one-quarter of casein, presents a valuable raw material for generating peptides with potential health benefits. These peptides exhibit properties such as antioxidant, antimicrobial, anti-inflammatory, anticarcinogenic, antihypertensive, antithrombotic, opioid, mineral-binding, and growth-stimulating activities, contributing to improved human immunity and the treatment of chronic diseases. Enzymatic hydrolysis of milk proteins has been developed as a method to produce these peptides, facilitating their use in food fortification. To incorporate whey into functional beverages, it undergoes fermentation by lactic acid bacteria with proteolytic activity. To specifically enrich these beverages with peptides exhibiting targeted bioactivities, it is essential to select lactic acid bacteria strains possessing the requisite protease profiles. Additionally, the sensory properties of the final product can be enhanced using starter cultures with diverse metabolic capabilities, even in the absence of added flavoring agents. Given the imperative to develop waste-free technologies and enhance the profitability of the dairy industry, there is a growing need to efficiently utilize and transform acid whey into a broad spectrum of valuable products and food additives. This approach is justified not only by the nutritional benefits of the bioactive components in whey but also by the commercial potential of safe and health-enhancing products.

The paper focuses on the application of a multilevel, integrative and territorial approach to the protection of cultural heritage through planning instruments in Serbia. It points out the problems of the sectoral approach and discusses international recommendations that can be integrated into the planning methodology. The case study is the area of Djerdap National Park, which has an already established international and national importance. The research suggests that the cultural heritage in the area, with the exception of the Roman limes, is still recognized at the level of individual localities. The study emphasizes the importance of aligning all levels of governance to safeguard the whole spatial entity rather than focusing solely on its particular areas. The interna-tional and national importance of the planning area contributes to the strengthening of awareness of heritage and its institutional protection. However, the vitality of the area, which is key to its sustainable development, comes from the local level. Planning documents contribute to the inte-gration of local values and local communities into development programs and projects.

In order to shorten the detection time and improve the average precision on embedded devices, A lightweight and high accuracy model is proposed for passion fruit in complex environments (backlight, occlusion, overlap, sunny, cloudy, rainy). Firstly, replacing the backbone network of YOLOv5 with a lightweight GhostNet model reduces the number of parameters and computation while improving detection speed. Secondly, a new feature branch is added to the GhostNet network, and the feature fusion layer in the neck network is reconstructed to effectively combine the lower-level and higher-level features, which not only improves the accuracy of the model but also maintains its lightweight. Finally, the knowledge distillation methods are used to transfer the knowledge from the more capable teacher model to the less capable student model, which significantly improving the detection accuracy. The improved model is denoted as G-YOLO-NK. The average accuracy of the G-YOLO-NK network is 96.00%, which is 1.00% higher than the original YOLOv5s model. Furthermore, the improved model size is 7.14MB, reduced to half of the original model, and the real-time detection frame rate is 11.25 FPS on the Jetson Nano. Compared to the state-of-the-art model, the proposed model outperforms them in terms of average precision and detection performance. The present work provides an effective model for real-time detection of passion fruits in complex orchard scenes, which can provide valuable technical support for the development of orchard picking robots and greatly improve the intelligence level of orchards.

The Simultaneous Localization And Mapping (SLAM) scanner is an easy and portable Light Detection And Ranging (LiDAR) data acquisition device. Its main output is a 3D point cloud covering the scanned scene. Regarding the importance of accuracy in the survey domain, this paper aims to assess the accuracy of two SLAM scanners: the NavVis VLX and the BLK2GO Scanner. This assessment is conducted for both outdoor and indoor environments. In this context, two types of reference data are used: the Total Station (TS) and the static scanner Z+F Imager 5016. To carry out the assessment, four comparisons are tested: cloud to cloud, cloud to mesh, mesh to mesh, and edge detection board assessment. However, the results of the assessments confirm that the accuracy of indoor SLAM scanner measurements (5 mm) is greater than that of outdoor ones (between 10 mm and 60 mm). Moreover, the comparison of cloud to cloud provides the best accuracy regarding direct accuracy measurement without manipulations. Finally, based on the high accuracy, scanning speed, flexibility, and the accuracy differences between tested cases, it is confirmed that SLAM scanners are effective tools for data acquisition.

The impact of interaction SS with MJO on rainfall along Java Island to East Nusa Tenggara has been studied using daily rainfall observation data from 2140 weather observation stations, which are also equipped with GSMaP, OLR, and ERA5 data. There were 61 SS events found, 17 during active MJO and 44 in inactive MJO. Rainfall increases more in the western study area when the active MJO and more in the eastern study area when the inactive MJO is due to SS. SS reduces rainfall in the Jakarta region, regardless of the activity or inactivity of the MJO. SS causes extreme rainfall to only occur in a small part of certain areas, so it tends to significantly reduce the possibility of extreme rainfall. In the southern part of the IMC, SS predominates over MJO in supporting increased water vapor transport. Large-scale synoptic circulations like the monsoon, SS, and MJO can interact with local land-sea wind circulation to produce spatiotemporal variability in rainfall on Java Island. Rainfall mostly increases in the afternoon and decreases in the morning when SS occurs, whether there is MJO or not. Convective instability analysis indicates that SS increases precipitation, most likely by lowering CIN and raising VIMFC.

Glycosidic linkage analysis was conducted on the unfractionated polysaccharides in the alcohol-insoluble residues (AIRs) prepared from six red seaweeds (Gracilariopsis sp., Prionitis sp., Mastocarpus papillatus, Callophyllis sp., Mazzaella splendens, and Palmaria palmata) using GC-MS/FID analysis of partially methylated alditol acetates (PMAAs). The cell walls of P. palmata primarily contained mixed-linkage xylans and small amounts of sulfated galactans and cellulose. In contrast, the unfractionated polysaccharides of the other five species were rich in galactans displaying diverse 3,6-anhydro-galactose and galactose linkages with varied sulfation patterns. Different levels of cellulose were also observed. This glycosidic linkage method offers advantages for cellulose analysis over traditional monosaccharide analysis that is known for underrepresenting glucose in crystalline cellulose. Relative linkage compositions calculated from GC-MS and GC-FID measurements showed that anhydro sugar linkages generated more response in the latter detection method. This improved linkage workflow presents a useful tool for studying polysaccharide structural variations across red seaweed species. Furthermore, for the first time, relative linkage compositions from GC-MS and GC-FID measurements, along with normalized FID and total ion current (TIC) chromatograms without peak assignments, were analyzed using principal component analysis (PCA) as a proof-of-concept demonstration of the technique's potential to differentiate various red seaweed species.

Background: Educating college students about the importance of good sleep habits could lead to the adoption of healthier sleep routines, including sufficient sleep duration and sleep quality. The current pre-post study examines the impact of completing a sleep education program called “Sleep 101” on (1) sleep hygiene practices, (2) sleep quality, and (3) weekday and weekend sleep behaviors among college students. “Sleep 101” is an interactive online course developed to educate college students about the importance of sleep by addressing basic sleep physiology, the impact of sleep on mood, academic and physical performance, the interactions between sleep and various substances, and common sleep disorders. Methods: 338 college students were recruited from a midsized public university in the US and invited to participate in “Sleep 101”, of which 25 participants completed the baseline and post-intervention questionnaire. The Sleep Hygiene Index (SHI) was utilized to evaluate sleep hygiene practices, while standard questions were employed to assess weekday and weekend sleep behaviors and overall sleep quality. Results: Those who completed the study demonstrated a significant increase in weekday sleep duration and were less likely to engage in negative prior bedtime activities. In addition, 40% of those who completed baseline and post-intervention assessments noticed improvements in their sleep quality. Conclusion: These findings suggest that a brief online program is beneficial in improving sleep behaviors among college and could be a scalable approach to addressing current sleep issues and preventing future sleep problems in college students.

The profile of secondary metabolites occurring in apple cuticular layer is not only characteristic for particular apple cultivar, but also dynamically reflects various external factors in growing environment. In this study, the possibility to authenticate apple samples based on analysis of their cuticular layer extracts was investigated. Ultra-high-performance liquid chromatography coupled to high resolution tandem mass spectrometry (UHPLC-HRMS/MS) was employed for obtaining metabolomic fingerprints. In total, 274 authentic apple samples, four cultivars harvested within the seasons 2020 to 2022 in the Czech Republic and Poland were analysed. The generated complex data processed by univariate and multivariate statistical methods enabled to build classification models for discrimination of apple cultivars as well as their geographical origin. The models showed very good performance in differentiation of Czech and Polish samples for three of four cultivars: ‘Gala’, ‘Golden Delicious’ and ‘Idared’, moreover, the validity of the models was verified over harvest seasons. The diagnostic markers, besides metabolites of triterpene biosynthetic pathway, mainly represented wax esters. ‘Jonagold’, which is known to be susceptible to mutations, was the only cultivar for which the unambiguous classification of geographical origin was not possible.