Nowadays, in order to improve asphalt pavement performance, durability and reduce environmental pollution caused by asphalt binder, many researchers are studying to modify asphalt concrete (AC) and find alternative paving materials to extend service life of asphalt pavement. One of the successful materials used in a modification of AC are fibers. Different types of fibers have been reinforced in AC mixture and improvements have been observed. This research studies the performance of glass wool fiber reinforced in a dense-graded asphalt mixture. Generally, glass fibers are known to have excellent mechanical properties such as high tensile modulus, 100% elastic recovery and a very high tolerance to heat. The glass wool fibers are commonly used as a thermal insulation material. In this research to evaluate the performance of glass wool fiber in AC, laboratory tests Marshall mix design test, Indirect tensile strength (IDT), Tensile strength ratio (TSR) and Kim test were conducted to determine a proper mix design, tensile properties, moisture susceptibility, rutting and fatigue behaviors. Results show that addition of glass wool fibers does affect the properties of AC mixture. The use of glass wool fibers showed a positive consistence results, in which it improved the moisture susceptibility and rutting resistance of the AC. Also result showed addition of fiber increased tensile strength and toughness which indicates that fibers have a potential to resist distresses that occur on a surface of the road as a result of heavy traffic loading. The overall results showed that addition of glass wool fiber in AC mixture is beneficial in improving properties of AC pavements.

Mineral wool made from basalt fibers is frequently used as an insulating material in construction systems. In this study, both unused mineral wool, and wool obtained from the softened roofing area, were comprehensively analyzed in a laboratory using different characterization techniques. Firstly, the amount of initial water content and compressive strength at 10% deformation were determined. Secondly, microstructure and surface chemical composition were analysed by Scanning electron microscopy (SEM) equipped with energy dispersive x-ray spectroscopy (EDX). To study heterogeneities near the fiber surface and to examine cross-sectional composition, a Scanning transmission electron microscope (STEM) was used. Finally, to verify possible reasons for resin degradation, Thermogravimetry analysis and differential scanning colometry (TGA-DSC) were simultaneously carried out. The results show that natural aging under high humidity and thermal fluctuations greatly affects the surface morphology and chemical composition of fibrous composite. Phenol-formaldehyde and other hydrophobic compounds that protect fibers against moisture and give compressive resistance were found to be degraded.

Although being one of the most popular world fibres, wool industry is addressed with severe environmental allegations. While majority of scientific texts does not leave to much doubt about its production negative impact on the ecosystem, wool business does not stop to promote itself via green claims. The internet popular links present a divergent, positive picture of that material, where one might recognize parties being financially involved in such communication. As wool producers or organizations linked to wool business are top positioned in the web as providers of wool green image, the below article brings an interpretation of the industry greenwashing techniques. This comparative analysis of wool umbrella institutions’ webpages exposes myths endorsed about wool’s sustainability. The investigation follows case study of Woolmark brand, where associations to similar, highly ranked websites were conducted likewise. The results have been additionally matched with available scientific data from LCA relative statistics and The Higg Index, to provide contra argumentation from academic sources. The results of this paper could be used both by researchers or fashion lecturers, likewise by fashion marketers to recognize greenwashing techniques, to deliver adequate scientific numbers about unsustainable aspects of wool and to support them in creating a relevant content about wool’s environmental impacts.

The identification and quantitative determination of wool and fine animal fibers are of great interest in the textile field because of significant price differences between them and common adulterations in raw and processed textiles. Since animal fibers have remarkable similarities in their chemical and physical characteristics, specific identification methods have been studied and proposed following advances in analytical technologies. The identification methods of wool and fine animal fibers are reviewed in this paper and the results of relevant studies are listed and summarized, starting from classical microscopy methods which are still used today not only in Small to Medium Enterprises but also in large industries, research studies and quality control laboratories. Particular attention has been paid to image analysis, Nir spectroscopy and proteomics which constitute the most promising technologies of quality control in the manufacturing and trading of luxury textiles and can find application in forensic science and archeology.

In recent years, tremendous progress has been made in the development of rare-earth ion doped tellurite glass laser sources, ranging from watt and multiwatt level fiber lasers to nanowatt level microsphere lasers. Significant success has been achieved in extending the spectral range of tellurite fiber lasers generating at wavelengths beyond 2 μm as well as in theoretical understanding. This review is aimed at discussing the state of the art of neodymium-, erbium-, thulium-, and holmium-doped tellurite glass fiber and microsphere lasers.

Glass fibers slowly dissolve and age when exposed to water molecules. Such a phenomenon also occurs when glass fibers are inside fiber-reinforced composites protected by the matrix. This en-vironmental aging results in the deterioration of the mechanical properties of the composite. In structural applications, GFRPs are continuously exposed to water environments for decades (typically design lifetime is around 25 years or even more). During their lifetime, these materials are affected by various temperatures, pH acidity levels, mechanical loads, and the synergy of these factors. The rate of the degradation process depends on the nature of glass, sizing, fiber orientation, and environmental factors such as acidity, temperature, and mechanical stress. In this work, degradation of typical industrial grade R-glass fibers, when inside an epoxy fiber-reinforced composite, is studied experimentally and computationally. A Dissolving Cylinder Zero-Order Kinetic (DCZOK) model was applied and could describe the long-term dissolution of glass composites, considering the influence of fiber orientation (hoop vs transverse), pH (1.7, 4.0, 5.7, 7.0, and 10.0), and temperature (20, 40, 60, and 80 °C). The limitations of the DCZOK model and effects of sizing protection, accumulation of degradation products inside the composite, and water availability were discussed. Experimentally dissolution was measured using ICP-MS. Like for the fibers, for GFRPs also, the temperature showed an Arrhenius-type influence on the ki-netics, increasing the rate of dissolution exponentially with increasing temperature. Similar to fibers, GFRPs showed a hyperbolic dependence on pH. The model was able to capture all of these effects, and the limitations were addressed.

Balance requires constant adjustments in muscle activation to attain force steadiness. Creating appropriate training can be challenging. The purpose of this study was to examine the effects of two weeks front squat instability training using a water-filled training tube on force steadiness during an instability challenge. Control (CON, n= 13) and experimental (EXP, n=17) subjects completed pre and post testing for EMG variability by completing one set of 10 repetitions with a stable and unstable training tube. Electrodes were placed bilaterally on the anterior deltoid, paraspinal and vastus lateralis muscles. CON subjects completed 2 weeks of training using a stable training tube, while EXP subjects trained with a water-filled instability tube. EMG data were integrated for each contraction and force steadiness computed using the natural log of coefficient of variation. CON results showed no changes in force steadiness for any condition. EXP showed significant reductions in EMG activation variability across all muscles. These results indicate a significant training effect in reducing muscle activation variability in subjects training with a water-filled instability training device. Improvements seen in these healthy subjects supports development of training implements for a more clinical population to help improve force steadiness.

Lignin fibers typically influence the mixture performance of stone matrix asphalt (SMA), such as strength, stability, durability, noise level, rutting resistance, fatigue life, and water sensitivity. However, limited studies were conducted to analyze the influence of fibers on the percent voids in mineral aggregate in bituminous mixture (VMA) during the mixture design. This study analyzed the effect of different fibers and fiber contents on the VMA in SMA mixture design. A surface-dry condition method test and Marshall Stability test were applied on the SMA mixture with four different fibers (i.e., flocculent lignin fiber, mineral fiber, polyester fiber, blended fiber). The test results indicated that the bulk specific gravity of SMA mixtures and asphalt saturation decreased with the increasing fiber content, whilst the percent air voids in bituminous mixtures (VV), Marshall Stability and VMA increased. Mineral fiber had the most obvious impact on the bulk specific gravity of bituminous mixtures, while flocculent lignin fiber had a minimal impact. The mixture with mineral fiber and polyester fiber had significant effects on the volumetric properties, and, consequently, exhibited better VMA over the conventional SMA mixture with lignin fiber. Modified fiber content range was also provided, which will widen the utilization of mineral fiber and polyester fiber in the applications of SMA mixtures. The mixture evaluation suggested no statistically significant difference between lignin fiber and polyester fiber on the stability. The mineral fiber required a much larger fiber content to improve the mixture performance than other fibers. Overall, the results can be a reference to guide SMA mixture design.

In the realm of physical activity and sports science, motion tracking emerges as an important tool for specialists aiming to analyze movement data, whether for daily life activities or enhancing athletic performance. This study introduces an innovative approach to motion tracking through the development of a fully embedded smart shoe sensor system, which employs an inertial measurement unit (IMU) affixed to the shoe sole, coupled with six pressure sensors, to provide real-time calculation of individual stride lengths along with other vital movement statistics. Traditional motion tracking methods, which typically rely on various body-attached sensors, often necessitate substantial post-processing, delaying the feedback loop. In contrast, our system is designed to overcome these limitations by offering high-accuracy, real-time feedback with a minimal error rate of 1.88% from our experiments. Such prompt data acquisition facilitates immediate interventions by sports performance coaches or healthcare professionals, significantly contributing to injury prevention and performance enhancement. The experimental outcomes of this study underscore the system’s capability to deliver precise stride length measurements instantaneously, marking a significant advancement in motion tracking technology and its application in sports science and healthcare.

In this study we have investigated the effect of the addition of Nb2O5 (up to 5 mol%) on the structure and luminescent properties of ZnO-B2O3 glass doped with 0.5 mol % Eu2O3 by using of infrared (IR), Raman and photoluminescence (PL) spectroscopy. Physical properties as molar volume, oxygen packing density and glass transition temperature were determined using the results of differential thermal analyisis (DTA) and Archimedes principle for density. IR and Raman spectra revealed that niobium ions incorporate into the base zinc borate glass as NbO4 trtraherda and NbO6 octahedra. A strong red emission from the 5D0 level of Eu3+ ions was registered under near UV (392 nm) excitation using the sharp 7F0 - 5L6 transition of Eu3+. The integrated fluorescence intensity ratio R (5D0 → 7F2/5D0 → 7F1) was calculated to estimate the degree of asymmetry around the active ion, suggesting a location of Eu3+ in non-centrosymmetric sites. The higher Еu3+ luminescence emission observed in zinc borate glasses containing 1÷5 mol% Nb2O5 compared to the Nb2O5-free zinc borate glass evidences that Nb2O5 is suitable component for modification of host glass structure and improving the emission intensity.

The advancement in science and technology has led to luffa sponge (LS) being widely used as a natural material in industrial application as its polyporous structure and light texture. In order to enhance the utility of LS fibers as the reinforcement of lightweight composite materials, this study investigate its water absorption, mechanical properties, anatomical characteristic and thermal performance. Hence, moisture regain, tensile properties of LS fiber bundles were measured in accordance with standards and the structural characteristics were investigated via microscopic observation. Scanning electron microscopy (SEM) was used to observe the surface morphology and fracture surface of fiber bundles. Test results shows that the special structure where the phloem tissues degenerate to cavities had a significant influence on the mechanical properties of LS fiber bundles. Additionally, the transverse sectional area occupied by fibers in a fiber bundle (SF), wall thickness and ratio of wall to lumen of fiber cell, and crystallinity of cellulose had an impact on the mechanical properties of LS fiber bundles. Furthermore, the fiber bundles density of LS varies range of 385.46-468.70 kg/m³, much less than that of jute (1360.40 kg/m³) and Arenga engleri (950.20 kg/m³) while LS fiber bundles has superior specific modulus.

Ensembles of Species Distribution Models (SDMs) represent the geographic ranges of pathogen vectors by combining alternative analytical approaches and merging information on vector occurrences with more extensive environmental data. Biased collection data impact SDMs, regardless of the target species but no studies have compared the differences in the distributions predicted by the ensemble models when different sampling frameworks are used for the same species. We compared Ensemble SDMs for two important Ixodid tick vectors, Amblyomma americanum and Ixodes scapularis in mainland Florida, USA, when inputs were either convenience samples of ticks, or collections obtained using the standard protocols promulgated by the U.S. Centers for Disease Control and Prevention. The Ensemble SDMs for the convenience samples and standard surveys showed only a slight agreement (Kappa = 0.060, A. americanum; 0.053, I. scapularis). Convenience sample SDMs indicated A. americanum and I. scapularis should be absent from 34.5% and 30.9% of the state where standard surveys predicted the highest likelihood of occurrence of the respective vectors. Ensemble models from standard surveys predicted 81.4% and 72.5% (A. americanum and I. scapularis) of convenience sample sites. Omission errors by standard survey SDMs, of the convenience collections, frequently were associated with adjacency to at least one SDM or errors in geocoding algorithms that failed to correctly locate convenience samples. These geocoding errors emphasize commonly overlooked needs to explicitly evaluate and improve data quality for vector survey data used in spatial models.

A low-cost bio-mass-derived carbon substrate has been employed to synthesize MoS₂@carbon composites through a hydrothermal method. Carbon fibers derived from natural cotton provide a three-dimensional and open framework for the uniform growth of MoS₂ nanosheets, thus constructing hierarchically coaxial architecture. The unique structure could synergistically benefit fast Li-ion and electron transport from the conductive carbon scaffold and porous MoS₂ nanostructures. As a result, the MoS₂@carbon composites, when served as anodes for Li-ion batteries, exhibit a high reversible specific capacity of 820 mAh g^-1, high-rate capability (457 mAh g^-1 at 2 A g^-1), and excellent cycling stability. The superior electrochemical performance makes the MoS₂@carbon composites to be low-cost and promising anode materials for Li-ion batteries.

Electrospun ultrathin fibers based on binary compositions of polylactide (PLA) and poly(ε-caprolactone) (PCL) with different ratios of polymer components from 0/100 to 100/0 wt. % were studied. Using a combination of thermal (DSC) and relaxation (EPR) measurements, the effect of biopolymers content on the characteristics of the crystal structure of PLA and PCL and the diffusive rotational mobility of the stable TEMPO radical in the amorphous regions of PLA/PCL compositions was shown. It was revealed that after PLA and PCL blending, significant changes in the degree of crystallinity of PLA, PCL segmental mobility, sorption capacity of the radical as well as activation energy of rotational diffusion in the amorphous regions of PLA/PCL composition are observed. The characteristic region of biopolymers’ composition from 50/50 to 30/70 % PLA/PCL blends ratio was found, where the inversion transition of PLA from dispersive medium to dispersive phase where an inversion transition is assumed when the continuous medium of the PLA transforms into a discrete phase. The performed studies made it possible for the first time to carry out a comprehensive analysis of the effect of the system component ratio on the structural and dynamic characteristics of the PLA/PCL film material at the molecular level.

In this paper glass crystallization behavior of 50ZnO:47B2O3:3Nb2O3:0.5Eu2O3 (G-0h) glass has been investigated in detail by DSC, XRD and TEM analysis. The luminescent properties of resulted glass-ceramics were also investigated. By XRD and TEM analysis crystallization of several crystalline phases have been proved (α-Zn3B2O6, β-Zn3B2O6 and ZnNb2O6). By calculating of crystal parameters it was found that europium ions are successfully incorporated in the β-Zn3B2O6. Photo-luminescent spectra show an increased emission in the resulting glass-ceramic samples as compared with the parent glass sample because of the higher asymmetry of Eu3+ ions in the crystalline phases obtained. It was established that the optimum emission intensity is registered for glass-ceramic sample obtained after 25 hours heat treatment of the parent glass.

Among magnetoelectric (ME) heterostructures, ME laminates of the type Metglas-like / PVDF (magnetostrictive+piezoelectric constituents) have shown the highest induced ME voltages, usually detected at the magnetoelastic resonance of the magnetostrictive constituent. This ME coupling happens because of the high cross-correlation coupling between magnetostrictive and piezoelectric material, and is usually associated with a promising application scenario for sensors or actuators. In this work we detail the basis of the operation of such devices, as well as some arising questions (as size effects) concerning their best performance. Also, some examples of their use as very sensitive magnetic fields sensors or innovative energy harvesting devices will be presented At the end, the challenges, future perspectives and technical difficulties that will determine the success of ME composites for sensor applications are discussed.

Millions of tons of wool waste are produced yearly by textile industries, which may become a serious environmental hazard in the near future. Given this concern, it is crucial to explore strategies to reduce the amount of wool waste generated worldwide and adopt more sustainable practices for dissolving and regenerating wool keratin (WK) from textile waste. Most traditional methods involve the use of expensive, toxic, harmful, and poorly biodegradable compounds. To overcome these limitations and facilitate the reuse of wool waste through a cascade valorization strategy, researchers have started testing the use of deep eutectic solvents (DES) as a more sus-tainable and eco-friendlier alternative for WK dissolution and regeneration. In this study, the potential of two different DES mixtures, Choline chloride (ChCl): Urea and L-Cysteine (L-Cys): Lactic acid (LA), was explored for dissolving wool waste. Subsequently, the obtained gels based on DES-WK were blended with polyvinyl alcohol (PVA) in different ratios to produce nanofibers using the electrospinning technique. The effect of pH and the properties of the electrospinning solutions, namely electrical conductivity and viscosity, on the morphology of the gel solutions were evaluated. Moreover, the morphological features of the produced gel-based electrospun PVA/DES-WK nanofibrous membranes were analyzed using scanning electron mi-croscopy (SEM). Additionally, the PVA/L-Cys: LA DES-WK, which proved to be the most effective DES mixture for fabricating WK gel-based nanofibers, were characterized through Fourier transform infrared spectroscopy (FTIR) and tensile tests. Furthermore, their antioxidant and an-timicrobial abilities were evaluated. The results obtained revealed that this approach to valorize textile waste offers a unique avenue for the development of sustainable functional materials with potential applications in various biomedical and industrial fields.

Concrete being one of the most frequently used construction materials in the field of construction. The use of concrete has increased with the passage of time as the more and more construction activities are taking place around the globe. Different materials have been added in to the concrete mix to provide the concrete more strength and make it more durable and long lasting. This paper looks into a detailed comparison of concrete strength when casted with in the presence of carbon fibers, steel fibers and glass fibers. The compressive strength for cubes and cylinder with carbon fibers is the highest as compare to steel fibers as well as glass fibers. The compressive strength of concrete is measured on 3 day, 7 day, 14 day and 28 day strength. The compressive strength of cube on 28th day strength is 37.52 MPa for carbon fiber steel, for steel fiber it is 34.22 MPa and with glass fiber the strength is 29.335 MPa whereas the compressive strength of cylinder with carbon fibers the 34.88 MPa, with steel fiber it is 34.22 MPa and with glass fiber the strength is 27.447 MPa. For the cubes the maximum difference between different fibers inducted concrete sample is 28% approximately and for cylinder it is 27%, respectively. On the other hand, the tensile strength of concrete was also gained with the carbon fiber. It was determined that carbon fiber provided about 16% and 12.8% tensile strength higher than glass and steel fibers respectively.

Interest grows in designing silicon-on-insulator slot waveguides to trap optical fields in subwavelength-scale slots and developing their optofluidic devices. However, it is worth noting that the inherent limitations of the waveguide structures may result in high optical losses and short optical paths, which challenge the device performance in optofluidics. Incorporating the planar silicon-based slot waveguide concept into a silica-based hollow-core fiber can provide a perfect solution to realize an efficient optofluidic waveguide. Here we propose a subwavelength-scale liquid-core hybrid fiber (LCHF), where the core is filled with carbon disulfide and surrounded by a silicon ring in a silica background. The waveguide properties and the Stimulated Raman Scattering (SRS) effect in the LCHF are investigated. The fraction of power inside the core of 56.3% allows an improved sensitivity in optical sensing; while the modal Raman gain of 23.60 m-1·W-1 is 2 times larger than that generated around a nano fiber with the interaction between the evanescent optical field and the surrounding Raman media benzene-methanol, which enables a significant low-threshold SRS effect. Besides, this in-fiber structure features compactness, robustness, flexibility, ease of implementation in both trace sample consumption and reasonable liquid filling duration, as well as compatibility with optical fiber systems. The detailed analyses of the properties and utilizations of the LCHF suggest a promising in-fiber optofluidic platform, which provides a novel insight into optofluidic devices, optical sensing, nonlinear optics, etc.

There are various approaches to managing polyethylene terephthalate waste, including methods for recycling PET. However, at present, only the cleanest wastes that can already be efficiently recycled using known methods are considered in the scientific literature. The study aims to look at other forms of polyethylene terephthalate waste that pose a challenge: low quality PET flakes, polyester tire cord, PET dust and prepolymer waste. The waste was characterized by FTIR spectroscopy, viscosimetry, differential scanning calorimetry, laser diffraction and sieve analysis. The findings describe the composition and properties of various forms of polyethylene terephthalate waste. Low quality PET flake waste and polyethylene terephthalate dust have been shown to be suitable for all chemical recycling methods. When recycling waste polyester tire cord, it is difficult to completely separate the rubber, so its presence in the final product must be taken into account. The most promising way to process a prepolymer is its depolymerization by hydrolysis, alcoholysis or glycolysis to produce monomers for the synthesis of PET, similar in properties to the primary one.

Abstract: Although the pathophysiology of fibromyalgia syndrome has been better understood in recent decades, a unified model of its pathogenesis and an effective therapeutic approach are still far from being realized. The main aim of this article will be to delve into the fundamental mechanisms of the pathophysiology of fibromyalgia conceptualized as stress intolerance syndrome. Using the biopsychosocial model of chronic pain syndromes, we will describe the potential role of the attachment system, C tactile fibers, and oxytocinergic system dysfunction in the pathophysiology of fibromyalgia syndrome and other central sensitivity syndromes. At the end of the article, the therapeutic implications of this new global and translational pathophysiological model will be briefly discussed.

The purpose of the review is to provide new insight into the potential of surface modification of carbon fibers for enhancing the application of the carbon fibers many a fold. To this end a total of 429 papers on the subject of surface modication of carbon fibers by a variety of chemical and electrochemical methods published during the period from 2010-2022 have been reviewed. Astounding results of surface funcationalization of carbon fibers by a variety of state of the art methods resulting in the unconventional applications of the resulting modified carbon fibers are summarized in a nut-shell in schemes from 1-6 towards the end of the review. Surface modifica-tion induces functionality to carbon fibers (CFs). The vitality of CF surface modification reac-tions could only be compared to the life process of respiration that sustains the multi functional-ity of living cells. Applicability of CFs can be drastically enhanced in incomprehensible ways by surface modification. Upon surface modification, inert and non-reactive CF surface becomes chemically active and functional with utility in diverse fields, namely, health, energy, environ-ment, defense, catalysis, smart materials and many others. Surface modification methods can be broadly classified into chemical, electrochemical and physical methods. By these surface modi-fication methods, the inert FC surface becomes polar. Surface properties like roughness, wetta-bility and energy are enhanced. Modification processes like sizing, oxidation, amination, si-lanization, polymerization, nanoarchitecture induces multifunctionality on CF surface. Modi-fied CFs when used as reinforcing material in carbon fiber reinforced plastics (CFRPs), im-proved bonding at the interface with resin matrices is observed with enhanced and outstanding mechanical properties (flexural strength, flexural modulus, IFSS, ILSS, hardness, elastic modulus, bending strength and compression strength).

In this study, the mechanical and piezoresistive properties of mortars reinforced with carbon nanotubes (CNTs) and carbon micro fibers (CMFs) are determined. Silica fume as well as a polymer with polyalkylene glycol graft chains were used as dispersant agents for the CNTs and CMFs incorporation into the cement paste. The mechanical properties of the mortar composites were investigated in respect to their flexural and compressive strength. A four-probe method was used for the estimation of their piezoresistive response. The test outcomes revealed that the combination of the dispersant agents along with a low content of CNTs and CMF by weight of cement (bwoc) result in the production of a stronger mortar with enhanced mechanical performance and durability. More specifically, there was an increase in flexural and compressive strength up to 38% and 88%, respectively. Moreover, the piezoresistive response of the reinforced cementitious materials was attributed to the variation of electrical resistivity due to tunneling transport of electrons stemming from two different mechanisms due to the incorporation of the conductive admixtures (CNTs and CMF). This work aims to contribute to the progress acceleration in the field of developing structural materials with self-sensing and electrical actuation related properties.

The Vogel-Fulcher-Tammann equation is exposed as a particular example of the mean field theory. It is generalized by taking into account an arbitrary critical exponent of susceptibility, discriminating between different classes of universality. The Bell-Evans-Polanyi principle is employed to estimate the difference between the activation energies of flows in crystals and glasses, which appears to coincide with the excess Gibbs energy of the glass compared to the crystal.

In this study, 10%PTFE/PEEK blend were modified by potassium titanate whisker (PTW) and chopped glass fiber (GF), respectively. The blends were prepared by three-screw extruder. Through the investigation of thermal stability, tribological properties, mechanical properties and rheological behavior, the effects of reinforcing agents were determined. The results illustrated that the mechanical properties of 10%PTFE/PEEK blend can be dramatically improved by adding reinforcing agent of PTW or GF, and the reinforcing effect of GF was especially obvious. As for tribological properties, 1% addition was the best proportion. The friction coefficient and wear rate of the blend with 1% PTW were 0.283 and 4.97 × 10^-6 mm³/N · m, which decreased by 7.2% and 21% compared with those of the blend without reinforcing agent.

Recycling upholstery textiles is challenging due to the complexity of materials, which often include a mix of fabrics, foams, and adhesives that are difficult to separate. The intricate designs and layers in upholstered furniture make it labor-intensive and costly to dismantle for recycling. Additionally, contaminants like stains, finishes, and flame retardants complicate recycling. Despite these difficulties, recycling upholstery textiles is crucial to reducing landfill waste and conserving resources by reusing valuable materials. It also helps mitigate environmental pollution and carbon emissions associated with producing new textiles from virgin resources. The presented research aimed to establish the feasibility of incorporating textile fibers from waste artificial leather fibers from the upholstery furniture industry into the structure of high-density fiberboards. This approach positively contributes to carbon capture and storage (CCS) policy and mitigates the problem of such waste being sent to landfills. The research shows that while selected mechanical and physical parameters of the panels decrease with a rising content of recycled textile fibers, it is possible to meet proper European standard requirements by adjusting technological parameters such as nominal density.

Re-creation of the past of historical buildings sits at the intersection of the spatio-temporal manifestation of cultural memories, socio-cultural meanings, values and identity re-moulds and refines the existing understanding and sense of place. Digital technologies have become a popular tool in re-creation of the past by creating a new body of knowledge and historical discourse based on identifying the gaps within our written histories. Designers and policymakers around the world have been exploring various tools and technologies such as diachronic modelling yet there is a gap in evidence-based understanding regarding the actual functioning and success of application for place making. This paper, therefore, sets out to scrutinise the role of digital technologies in facilitating digital place making. To do so, it investigates the potential of a new “digital heritage” narrative in the revival of the lost architectural narrative of the Dennys Lascelles Wool Store, Geelong. The proposed paper aims to investigate the potential of a new “digital heritage” narrative and story-telling as a means towards digital place making framework. While exploring the new and unique capabilities provided by the digital narrative in capturing, simulating and disseminating ‘lost’ heritage it will further imbue a sense of place by connecting the everyday city dweller.

This study aimed to enhance the compatibility of glass ionomer cement (GIC) with tooth tissue by chemically modifying its primary component, calciumfluoroaluminosilicate (CFAS), through the incorporation of nanorod hydroxyapatite (nHA). The process involved binding L-glutamic acid to nHA, followed by activation and binding of albumin to create nHA immobilized with albumin. This modified nHA was then used to surface-modify CFAS particles, producing nHA-CFAS powder. The modified powder was mixed with poly(acrylic acid) and UV-cured to form GIC containing nHA-CFAS (GIC-nHA). Fourier transform infrared spectroscopy and scanning electron microscopy (SEM) confirmed the successful modification. Cytocompatibility tests with osteoblasts showed that GIC-nHA had superior cell viability and bone formation capabilities compared to the control GIC. The improved histocompatibility is attributed to nHA enhancing the biological activity of osteoblasts, indicating that the surface modification method significantly improves the functional integration of GIC with tooth tissue.

In recent years, compound glass microsphere resonator devices have attracted increasing interest and have been widely used in sensing, microsphere lasers, and nonlinear optics. Compared with traditional silica resonators, compound glass microsphere resonators have many significant and attractive properties, such as high-Q factor, an ability to achieve high rare earth ion, wide infrared transmittance and low phonon energy. This review provides a summary and a critical assessment of the fabrication and the optical characterization of compound glasses and the related fabrication and applications of compound glass microsphere resonators.

The treatment of wastewater containing heavy metals and the utilization of wool waste are very important for the sustainable development of textile mills. In this study, the wool keratin modified magnetite (Fe3O4) powders were fabricated by using wool waste via a co-precipitation technique for removal of Cu2+ ions from aqueous solutions. The morphology, chemical compositions, crystal structure, microstructure, magnetism properties, organic content, and specific surface area of as-fabricated powders were systematically characterized by various techniques including field emission scanning electron microscopy (FESEM), energy dispersive spectroscopy (EDS), X-ray diffraction (XRD), transmission electron microscopy (TEM), X-ray photoelectron spectroscopy (XPS), vibrating sample magnetometer (VSM), thermogravimetric (TG) analysis, and BET surface area analyzer. The effects of experimental parameters such as the volume of wool keratin hydrolysate, the dosage of powder, the initial Cu2+ ion concentration, and the pH value of solution on the adsorption capacity of Cu2+ ions by the powders were examined. The experimental results indicated that the Cu2+ ion adsorption performance of the wool keratin modified Fe3O4 powders exhibited much better than that of the chitosan modified ones with a maximum Cu2+ adsorption capacity of 29.2 mg/g under favorable conditions (0.05 g powders; 50 mL of 40 mg/L CuSO4; pH 5; temperature 293 K). The high adsorption capacity towards Cu2+ ions on the wool keratin modified Fe3O4 powders was primarily because of the strong surface complexation of -COOH and -NH2 functional groups of wool keratins with Cu2+ ions. The Cu2+ ion adsorption process on the wool keratin modified Fe3O4 powders followed the Langmuir adsorption isotherm model and the pseudo-second-order adsorption kinetic model. After Cu2+ ion removal, the wool keratin modified Fe3O4 powders were easily separated using a magnet from aqueous solution and efficiently regenerated using 0.5 M EDTA-H2SO4 eluting. The wool keratin modified Fe3O4 powders possessed good regenerative performance after five cycles. This study provided a feasible way to utilize waste wool textiles for preparing magnetic biomass-based adsorbents for the removal of heavy metal ions from aqueous solutions.

This study aims to investigate the effect of banana stem fibers (BSFs) treatment with liquid smoke on changes in the micro-mechanics properties of BSFs, the tensile strength of single fibers, mor-phology, crystalline properties, and functional groups. The research used four model specimen variations, namely fiber without treatment and immersion in liquid smoke for 1, 2, and 3 hours. The BSFs with treatment was dried in an oven with a temperature of 40ºC for 30 minutes. Several tests were conducted, including a tensile test of single fiber capacity of 50N standard ASTM 3379-02, SEM observation, XRD, and FTIR test. The results showed that the highest increase in fiber strength was P2J, which was 264.21 MPa, and the lowest was TP fiber at 148.54 MPa. Fibers treatment with liquid smoke can form strong C-C elemental bonds caused by the H2O degradation process in BSFs, hence carbon atoms (C) are dense, and in conditions of excessive H2O degradation, the fiber strength will become brittle and the liquid smoke can increase the tensile strength of the fiber. The morphology of the fiber changed where the untreated fiber was covered with lignin, while the treated fiber had an elongated rectangular line pattern, porous, and the lignin was eroded. Crystalline properties in the X-ray diffractogram pattern differ between untreated and treated fibers. At an angle of 2ϴ, the lowest diffraction peak is around 160 in untreated wool, and the highest is 230 in treated fiber. The functional group of the fiber has changed where there is a difference in the wave crest between untreated and treatment fiber. The longer immersion time, the element of Carbon (C) will increase. In conclusion, treating BSFs with liquid smoke can change the physical, mechanical, and chemical properties, hence becoming a choice of composite reinforcement material in the future which is lightweight and environmentally friendly.

Solid waste management is a major environmental challenge, especially in developing countries, with increasing amounts of waste glass (WG) and waste plastics (WP) not being recycled. In Ethiopia, managing WG and WP requires innovative recycling techniques. This study examines concrete properties with WG and WP as partial replacements for fine aggregate. Tests were conducted on cement setting time, workability, compressive strength, splitting tensile strength, and flexural strength. Concrete grade C-25, with a compressive strength of 25 MPa, was prepared using an optimum ratio of 14% WG and 6% WP. Mechanical properties were tested at 7 and 28 days of curing. At 20% replacement, workability decreased at water-cement ratios of 0.5 and 0.6 but remained stable at 0.4. Thus, a 0.4 ratio was used. For 10% replacement, compressive strength increased by 12.55% and 6.44% on the 7th and 28th days, respectively. At 20% replacement, compressive strength decreased by 14.35% and 0.73% on the 7th and 28th days, respectively. On the 28th day, splitting tensile strength at optimum replacement was 4.3 MPa, an 8.5% reduction from the control mix. However, flexural strength increased by 19.7%, from 12.46 MPa to 15.52 MPa. Overall, WG and WP improved flexural strength but slightly reduced splitting tensile strength.

A novel five-surface phosphor-in-glass (FS-PiG) for high illumination and excellent color uniformity in larger-scale LEDs for sensor light source application is demonstrated. YAG phosphor (Y3Al5O12:Ce3+) was uniformly mixed with ceramic and sintered at 680°C to form a phosphor wafer. A sophisticated laser engraving was employed on the phosphor wafer to form a saddle-shaped large-scale FS-PiG LEDs. The performance of the FS-PiG LEDs exhibited the illumination of 401lm, average color temperature (CCT) of 5488K±110K, and color coordinates (CIE) of (0.3179±0.003, 0.3352±0.003). In contrast to convention single-surface phosphor-in-glass (SS-PiG) LEDs, the performance exhibited the illumination of 380lm, average CCT of 5830K±758K, and CIE of (0.3083±0.07, 0.3172±0.07). These indicated that the performance of the FS-PiG LEDs was higher than the SS-PiG LEDs for illumination, CCT, and CIE of 1.7, 7, and 23 times, respectively. Furthermore, the FS-PiG LEDs demonstrate lower lumen loss of 2% and less chromaticity shift of 5.4x10-3 under accelerated aging at 350°C for 1008 hours, owing to the high ceramic melting temperature of up to 510°C. In this study, the proposed FS-PiG larger-scale LEDs having excellent optical performance and high reliability may be the promising candidates to replace the convention phosphor-in-organic silicone material used in high-power LEDs for the next generation of sensor light sources, display, and headlight applications.

Filament wound composite pipes are frequently used in the field were transmission of high pressured chemical fluids, disposal of industrial wastes, oil and natural gas transmission takes place. In oil and gas industry, the pipelines transporting heavy crude oil are subjected to variable pressure waves causing fluctuating stress levels in the pipes. Computational Fluid Dynamics Analysis was performed using Ansys 15.0 Fluent software to study the effects of these pressure waves on some specified joints in the pipes. Depending on the type of heavy crude oil being used, the flow behavior indicated a considerable degree of stress levels in certain connecting joints, causing the joints to become weak over a prolonged period of use. In this research comparison of various pipe joints was done by using different material and the output result of the stress levels of the pipe joints were checked so that the life of the pipe joints can be optimized by the change of material.

Chemical modification of cellulose offers routes for structurally and functionally diverse biopolymer derivatives for numerous industrial applications. Among cellulose derivatives, cellulose ethers have found extensive use, such as emulsifiers, in food industries and biotechnology. Methylcellulose, one of the simplest cellulose derivatives, has been utilized for biomedical, construction materials and cell culture applications. Its improved water solubility, thermoresponsive gelation, and the ability to act as a matrix for various dopants also offer routes for cellulose-based functional materials. There has been a renewed interest in understanding the structural, mechanical, and optical properties of methylcellulose and its composites. This review focuses on the recent development in optically and mechanically tunable hydrogels derived from methylcellulose and methylcellulose-cellulose nanocrystal composites. We further discuss the application of the gels for preparing highly ductile and strong fibers. Finally, the emerging application of methylcellulose-based fibers as optical fibers and their application potentials are discussed.

The reinforcing effect of boehmite nanoparticles (BNP) in epoxy resins for fiber composite lightweight construction is related to the formation of a soft but bound interphase between filler and polymer. The interphase is able to dissipate crack propagation energy and consequently increases the fracture toughness of the epoxy resin. Usually, the nanoparticles are dispersed in the resin and then mixed with the hardener to form an applicable mixture to impregnate the fibers. If one wishes to locally increase the fracture toughness at particularly stressed positions of the fiber-reinforced polymer composites (FRPC), this could be done by spraying nanoparticles from a suspension. However, this would entail high costs for removing the nanoparticles from the ambient air. We propose that a fiber fleece containing bound nanoparticles be inserted at exposed locations. For the present proof-of-concept study, an electrospun polycarbonate nonwoven and taurine modified BNP are proposed. After fabrication of suitable PC/EP/BNP composites, the thermomechanical properties were tested by dynamic mechanical analysis (DMTA). Comparatively, the local nano-mechanical properties such as stiffness and elastic modulus were determined by atomic force microscopy (AFM). An additional investigation of the distribution of the nanoparticles in the epoxy matrix, which is a prerequisite for an effective nanocomposite, is carried out by scanning electron microscopy in transmission mode (TSEM). From the results it can be concluded that the concept of carrier fibers for nanoparticles is viable.

The aim in this paper is the presentation of the influence of modification of polypropylene (PP) fibres on sorption capabilities of fibres. Modification of PP fibres were made with inorganic additives in the mass with a view to improving silicate composites – in construction. The prepared modified PP fibres were compared with pure PP fibres and their mechanical and thermomechanical properties were evaluated. And we wanted to evaluate and compare the sorption capabilities of these fibres using the Washburn method. However, the obtained results led us to the conclusion that the given method rather points to the excellent transport properties of PP fibres, as if it evaluated the sorption of the fibres.

With the development of the volume of information exchange and perception increases, the demands for intelligent, miniaturized and integrated optical devices for information acquisition are also increasing. As the core component of optical networks for transmitting information, how to further optimize its structural characteristics to generate richer optical characteristics and apply them to information exchange and optical field control has become a key research hotspot. The introduction of chiral twist characteristics has led to new phenomena and applications in optical field transmission and transformation for traditional optical fibers or microstructured optical fibers (MOF). Therefore, this review mainly starts from the principle of chiral optical fibers, introduces their preparation and latest application scenarios, and finally looks forward to their potential future development prospects.

We provide a very general review of the resonant transmission line method for optical fiber problems. The method has been found to work seamlessly for a variety of difficult problems including elliptical and eccentric core fibers as well as “holey”, photonic crystal fibers. A latest version has been shown to offer great versatility with respect to cases of unconventional, inhomogeneous index profiles.

The conceptual and theoretical backbones of symmetry/asymmetry detections or similarity/dissimilarity, and identity/unidentity study are automorphism or isomorphism respectively. However, the development of equations and methods for symmetry/asymmetry detections, similarity/dissimilarity, and identity/unidentity measures deviates from these backbones. In this article, an equation was proposed for symmetry/asymmetry detections, similarity/dissimilarity, and identity/unidentity measures, and proved that its isoreflective pairs-points are functionally bijective and inverse. The proposal, called Kabirian-based optinalysis, is based on the conceptual and theoretical frameworks of automorphism and isomorphism. The Kabirian-based optinalysis is also proven and characterized as invariant (robust) under translation (i.e., scaling and location shift), and rotation or reflection. Computing codes were written in python language for Kabirian-based optinalysis to serve as working codes for application and verification.

The development of efficient luminescent systems, such as microcavities, solid state lasers, integrated optical amplifiers, optical sensors is the main topic in glass photonics. The building blocks of these systems are glass-ceramics activated by rare earth ions because they exhibit specific morphologic, structural and spectroscopic properties. Among various materials that could be used as nanocrystals to be imbedded in silica matrix, tin dioxide presents some interesting peculiarities, e.g. the presence of tin dioxide nanocrystals allows increase in both solubility and emission of rare earth ions. Here, we focus our attention on Er³⁺ - doped silica – tin dioxide photonic glass-ceramics fabricated by sol-gel route. Although the SiO₂-SnO₂:Er³⁺ could be fabricated in different geometrical systems: thin films, monoliths and planar waveguides we herein limit ourselves to the monoliths. The effective role of tin dioxide as luminescence sensitizer for Er³⁺ ions is confirmed by spectroscopic measurements and detailed fabrication protocols are discussed.

In this paper thermo-mechanical behavior of 4D printed Polylactic Acid (PLA) was investigated, focusing on its response to varying strain rates and temperatures below the glass transition temperature. Dynamic mechanical analysis and uniaxial tensile tests confirmed PLA's dependency on strain rate, showcasing its sensitivity to external stimuli. Stress-strain curves exhibited typical thermoplastic behavior, with yield stresses varying with strain rates, underscoring PLA's responsiveness to different deformation speeds. Clear strain rate dependence was observed, particularly at quasi-static rates, with temperature and strain rate fluctuations significantly influencing PLA's mechanical properties, including yield stress and deformation behavior. Isothermal compression tests demonstrated predictable stress-strain curves with distinct yield points, while adiabatic tests reveal additional complexities such as heat accumulation leading to further softening. Thermal imaging revealed temperature increase during deformation, highlighting the material's thermo-sensitive nature. These findings provide the basis for future research with the focus on advanced modeling techniques and mitigation strategies for self-heating effects, aiming to enhance PLA-based product reliability and performance in applications with deformations at higher strain rates, while also developing models to simulate shape recovery in 4D printed PLA structures at both cold and hot programming temperatures.

Nano/micron-sized bioactive glass (BG) particles are attractive candidates for both soft and hard tissue engineering. They can chemically bond to the host tissues, enhance new tissue formation, activate cell proliferation, stimulate the genetic expression of proteins, and trigger unique an-ti-bacterial, anti-inflammatory, and anti-cancer functionalities. Recently, composites based on bi-opolymers and BG particles have been developed with various state-of-the-art techniques for tis-sue engineering. Gelatin, a semi-synthetic biopolymer, has attracted the attention of researchers because it is derived from the most abundant protein in the body, viz., collagen. It is a polymer that can be dissolved in water and processed to acquire different configurations, such as hydro-gels, fibers, films, scaffolds, etc. Searching "bioactive glass gelatin" in the tile on Scopus renders 80 highly relevant articles published in the last ~10 years, which signifies the importance of such composites. First, this review addresses the basic concepts of soft and hard tissue engineering, in-cluding the healing mechanisms and limitations ahead. Then, current knowledge on gelatin/BG composites including composition, processing and properties is summarized and discussed both for soft and hard tissue applications. This review explores physical, chemical and mechanical features and ion-release effects of such composites concerning osteogenic and angiogenic respons-es in vivo and in vitro. Additionally, recent developments of BG/gelatin composites using 3D/4D printing for tissue engineering are presented. Finally, the perspectives and current challenges in developing desirable composites for the regeneration of different tissues are outlined.

Recycled tire fibers (RTF) are currently one of the most abundant waste not being recovered due to several processing hurdles and the presence of high amounts of residual ground rubber particles (GR). Therefore, this study proposes a simple approach to separate most of rubber particles from fibers and to determine their rubber content using thermogravimetric analysis (TGA)/calcination. Afterwards, clean fiber (CF) and GR are used as fillers for recycled post-consumer low density polyethylene (rLDPE), and their effects on the physical properties are investigated. Accordingly, a series of composites with CF and GR is prepared at different filler concentrations (0-30%) via extrusion compounding before using compression molding and injection molding for comparison. In all cases, injection molding leads to higher strength and modulus, but lower elongation at break. The results show that incorporating 30 wt.% of CF into rLDPE yields a remarkable improvement in tensile strength (15%), tensile modulus (192%) and flexural modulus (142%). On the other hand, the incorporation of up to 30 wt.% of GR results in a reduction of both tensile strength and flexural modulus by 15%, confirming the critical role of the cleaning process for RTF in achieving the best results.

Electrospinning is a simple versatile method to generate nanofibres. Remarkable progress has been made in the development of electrospinning process. The production of nanofibers is affected by many parameters, which influence the final material properties. Electrospun fibers have a wide range of applications such as energy storage and biomedical scaffolds. Polyacrylonitrile (PAN) has been widely used in the production of carbon nanofibers. PAN has received increasing interest in recent years, due to its excellent characteristics, such as spinnability, biocompatibility, and commercial viability, opening new applications in the biotechnological field. This paper provides an overview of the electrospinning process, its main parameters, and operation modes that affect nanofibers fabrication. A review of their biological applications is proposed. A focus is made on PAN fibers formation, functionalization, and application as scaffolds to allow cell growth. Overall, nanofibre scaffolds, made of stabilized PAN, appear as a powerful tool in medical applications needing controlled cell culture.

The present study investigates the failure mechanisms of industrial fiber materials, using a custom designed fiber cutting performance test bench. The fracture morphologies of single PA6 fibers are examined by scanning electron microscopy. The analysis reveals that fiber cutting can be distinguished according to four distinct stages of fiber failure represented by shearing, cutting, brittle fracture, and tensile failure, which are the result of different mechanisms active during the processes of crack initiation, extension and fracture. The results of fractographic analysis are further verified by an analysis of the blade assembly speed with respect to time over the entire fracture failure process based on high-speed camera data. The results of fractographic analysis and blade assembly speed are fully consistent.

Optical materials with a tunable localized surface plasmon resonance (LSPR) are of a great interest for applications in photonics and optoelectronics. In the present study we explored the potential of generating the LSPR band with an ultra-broad range of over 1000 nm in gold nanoparticles (NPs) precipitated through the thermal treatment in ZnO-Al2O3-SiO2 glass. Using the optical absorption spectroscopy, we demonstrated that the LSPR band's position and shape can be finely controlled by varying the thermal treatment route. Comprehensive methods including Raman spectroscopy, X-ray diffraction and high-resolution transmission electron microscopy were used to study the glass structure, while computational approaches were used for the theoretical description of the absorption spectra. Obtained results allowed us to suggest a scenario responsible for such abnormal LSPR band broadening which includes possible interparticle plasmonic coupling effect taking place during the liquid-liquid phase separation of the heat-treated glass. The formation of gold NPs with an ultra-broad LSPR band in glasses holds promise for sensitizing rare earth ion luminescence for new photonics devices.

Wearable computing is a fast evolving segment of computing that includes smart watches, head mounted wearables such as Magic Leap headsets, Microsoft Hololens, and VR goggles from various vendors. In this report, we present ideas for a smart wearable device that also doubles as a virus protection device. Instead of using the filtering approach that is predominantly used by virus protection equipments such as face masks, we propose to use a computational approach where the device maintains an awareness of the real-time virus spread and use that information to steer the wearer away from the virus. As the wearable has a head enclosing design, viral infection can only happen through the air that is inhaled by the wearer. The objective of the smart wearable is to maintain a repository for clean air and switch the operating modes between stored and fresh air modes depending on the environmental conditions. It can augment this basic operating procedure by recycling the exhaled air to maximize it operating capacity (i.e., time duration for which it could supply the wearer with safe air) and by cleaning the stored air using UVC to further reduces the chance of infection. To maintain an awareness of the virus spread in the environment, the smart wearable will rely on an edge computing framework that will be distributed to cover areas frequented by people. The smart wearable will have modular design so that it can be reconfigured to add or subtract functionality that the wearer wants for a particular situation so that the design remains relevant even after the virus threat recedes.

The açaí (Euterpe oleracea Mart.) is a native fruit of the Amazon that is well-known due to its commercial value. Its production chain is centered in the state of Pará, largely supplied by extractivism. The processing of açaí fruits in nature generates huge amount of solid waste, which can pose serious risks to the environment if not used and managed properly. Due to a small number of systhematic studies on the effect of chemical activation by pyrolysis of açaí seeds and fibers, and with the aim of providing a basis for future applications of the waste generated by processing of açaí fruits, the present work proposes a study of the pyrolysis of açaí seeds and fibers and the physicochemical and compositional characterization of the aqueous phase products. In this way, açaí seeds were collected from a local artisan processing facility in the city of Belém, PA. The seeds were dried at 105°C until constant weight, and subsequently, the fibers were separated from the seeds in a rotating drum. The seeds and fibers were impregnated with NaOH solutions at 0.5M, 1.0M, and 2.0M, and then pyrolyzed at a laboratory scale at 450 °C and 1 atm. The liquid products from pyrolysis were characterized through acidity index analysis, Fourier-transform infrared spectroscopy, and gas chromatography. The increase in the concentration of the impregnating agent resulted in an increase in bio-oil yield from both the seeds and fibers, rising from 3.3% (raw seeds) to 6.6% (seeds impregnated with 2M NaOH) and from 1.2% (raw fibers) to 3.7% (fibers impregnated with 2M NaOH). The yield in the aqueous phase after biomass pyrolysis showed an inverse behavior to the bio-oil yield, decreasing from 33.7% (raw fibers) to 21.2% (fibers impregnated with 2M NaOH) and from 41% (raw seeds) to 37.5% (seeds impregnated with 2.0M NaOH). High acidity levels were found in the aqueous phase samples and bio-oils derived from the seeds and fibers, which decreased as the concentration of the impregnating agent increased. The increase in the concentration of the impregnating agent (NaOH) influenced the chemical composition of the obtained liquid products, leading to a decrease in oxygenated compounds and an increase in nitrogenous compounds in both experimental matrices, which was also evidenced by the reduction in acidity.

The paper presents theoretical, experimental and numerical studies on the thermal behavior of mineral wool used in sandwich panels. The aim of this study is to investigate the thermal properties of mineral wool at elevated temperatures and provide a simple model that would allow to determine the heat propagation in sandwich panels during fire. The paper proposes a new method to experimentally evaluate thermal diffusivity, derived from theoretical premises. Experiments are conducted in a laboratory furnace, where specimens are placed and temperatures inside specimens are measured. Different methods are used to process the test results and calculate the thermal diffusivity of mineral wool. Finally, a numerical analysis of heat transfer using finite element method (FEM) is performed to validate the obtained thermal properties.

A single paragraph of about 200 words maximum. For research articles, abstracts should give a Ultra-high performance concrete (UHPC) has gained worldwide popularity because of its notable mechanical response. This research studied the compressive strength, modulus of elasticity, and flexural tensile strength of UHPC. Batches were made with the addition of steel and PVA fibers using a standard procedure defined in the research. The experimental data from the compressive strength test was analyzed in the Statistica 10 software to investigate the fibers' influence on UHPC's mechanical properties. An analysis of the elastic modulus prediction was carried out according to international standards. It was found that the normalized equations for the elastic modulus are not adequate for its estimation. The statistical analysis indicated that the range of fiber quantities analyzed did not significantly affect the compressive strength and the elastic modulus. Regarding the optimized mix, its flexural tensile strength indicates that the fiber content must be higher for UHPC to be suitable for structural use.

In the past decades, Fiber Reinforced Concrete has been gaining more attention in the concrete research development. There are many advantages of the inclusion of fiber into reinforced concrete structures. It was found that the inclusion of fibers in concrete, be it synthetic or natural, resulted in the improvement of the thermal properties of concrete, as well as its strength to some extent. However, the inclusion of fibers in concrete does affects its thermo-mechanical properties. The objective of this study is to identify the potential of the addition Polypropylene and Kenaf fibers in cement mortar at different compositions (0.1%, 0.2%, and 0.3%). Eight mixes were analyzed for this purpose. Upon investigating the flow ability, compressive strength, tensile strength, and thermal conductivity of the mortar samples, it was found that the incorporation of PP and Kenaf fibers reduced the flow ability. Cement mortar samples containing 0.1% addition of PP and Kenaf fibers show the highest compressive strength compared to other percentages, while samples containing 0.3% addition of PP and Kenaf fibers show the highest tensile strength compared to other percentages. The thermal conductivity of mortar samples shows reduction when high percentages of both fibers were used.

Façade elements are a building component that satisfies multiple performance parameters. Among other things, “advanced façades” take advantage of hybrid solutions, such as assembling laminated materials. In addition to the enhanced mechanical properties that are typical of optimally composed hybrid structural components, these systems are energy-efficient, durable, and offer lighting comfort and optimal thermal performance, an example of which is the structural solution developed in collaboration with the University of Zagreb and the University of Ljubljana within the Croatian Science Foundation VETROLIGNUM project. The design concept involves the mechanical interaction of timber and glass load-bearing members without sealing or bonding the glass-to-timber surfaces. Following earlier research efforts devoted to the structural analysis and optimization of thus-assembled hybrid Cross-Laminated Timber (CLT)-glass façade elements, in this paper, special focus is given to a thermal and energy performance investigation under ordinary operational conditions. A simplified numerical model representative of a full-size building is first presented by taking advantage of continuous ambient records from a Live-Lab mock-up facility in Zagreb. Afterwards, a more detailed Finite Element (FE) numerical analysis is carried out at the component level to further explore the potential of CLT–glass façade elements. The collected numerical results show that CLT–glass composite panels can offer stable and promising thermal performance for façades similar to national and European standard requirements.

This study presents, for the first time, the development of fibers with favorable properties for biodegradable wound dressings made from the Ecovio® (EC) polymer blend, composed of poly(lactic acid) (PLA) and poly(butylene adipate-co-terephthalate) (PBAT), incorporated with tea tree essential oil (TTE). TTE presented antimicrobial activity against Pseudomonas aeruginosa and Staphylococcus aureus, achieving minimal inhibitory concentrations of 15 and 7.5 mg/mL, respectively. The TTE was mixed with EC in a binary chloroform and formic acid (85/15 v/v) mixture, leading to homogeneous and wettable fibers by electrospinning. The EC/TTE fibers were characterized confirming the TTE in the fibers. The tests showed that TTE (0.5, 1.0 or 1.5 mL) improved the polymer blend electrospinnability. TTE (1.5 mL or 75 w% concerning the EC) lead to homogeneous fibers with an average diameter of 278 nm. TTE (75 w%) increased the wettability of the EC fibers from 120±2° to 69±1°. Preliminary bacterial adhesion and proliferation assays demonstrated that the EC/TTE fibers have anti-adhesive activity e seems to be more toxic against P. aeruginosa compared to S. aureus after 24 hours of incubation. Compatibility tests with human blood indicated that the EC/TTE fibers accelerate blood coagulation. The EC/TTE fibers exhibit promising chemical and biological properties (in vitro) for the development of wound dressings.

A frequent problem in Geotechnics is the soils with inadequate physical-mechanical properties before the efforts to which they will be subjected by the constructions, incurring cost overruns caused by their engineering improvement. The need to improve the engineering properties of soils is not recent, currently observing that the most common alternatives are binders such as cement and lime. The climate change observed in recent decades and the uncontrolled emission of greenhouse gases have motivated Geotechnical and Geoenvironmental researchers to seek mechanisms for soil reinforcement from a more sustainable and environmentally friendly approach by proposing the use of recycled and waste materials. An alternative is natural fibers, which can be obtained as waste from many agro-industrial processes, implying their high availability and low cost. Sawdust as a by-product of wood processing has a rough texture that can generate high friction between the fiber and the matrix of the soils, leading to a significant increase in its shearing strength and bearing capacity. This concept of improving the properties of soils using natural fibers distributed randomly is inspired by the natural phenomenon of grass and/or plants that when growing on a slope can effectively stabilize a said slope.

Single-fluid electrospinning creates nanofibers from molten polymer solutions with active ingredients. The study utilized a combination of a fractional factorial design and a Box-Behnken design to examine crucial factors among a multitude of parameters and to optimize the electrospinning conditions that impact the fiber mats' morphology and entrapment efficiency of the Senna alata leaf extract. The findings indicated that the shellac content had the greatest impact on both fiber diameter and bead formation. The optimum electrospinning conditions were identified as a voltage of 24 kV, a solution feed rate of 0.8 mL/h, and a shellac-extract ratio of 38.5:3.8. These conditions produced nanosized fibers with a diameter of 306 nm, a low bead-to-fiber ratio of 0.29, and an extract entrapment efficiency of 96% within the fibers. The biphasic profile of optimized nanofibers was confirmed through an in vitro release study. This profile consisted of an initial burst release of 88% within the first hour, which was succeeded by a sustained release pattern surpassing 90% for the next 12 h, as predicted by zero-order release kinetics. The optimized nanofibers demonstrated antimicrobial efficacy against diverse pathogens, suggesting promising applications in wound dressings and protective textiles.

This work seeks to approach the comparative analysis of the distribution of POFs (polymeric optical fibers) arranged in a random and sorted manner in the manufacture of translucent concretes. The following characteristics were analyzed: compressive strength, flexural tensile strength, capillary water absorption and light transmittance. Portland cement, water, fine aggregate (sand), silica fume, polycarboxylate ether-based superplasticizer and polymeric optical fiber were used in the production of the composites. Except the fiber content, the mixture of all other inputs was kept as a fixed parameter. Groups with the following levels of POFs were produced: 0%, 2%, 3.5% and 5%. The POF content is the sum of the areas of the fiber sections in the composite with the total area of the translucent surface. The results showed that for the analysis of mechanical behavior (flexural tensile and compressive strength) and durability (capillary water absorption), composites with random and sorted fibers within the 2% POF presented to belong to statistically distinct groups. For the other fiber contents, there was no pattern of behavior, that is, it cannot be said that there is a difference within 3.5% or 5% POF between sorted and random fibers in relation to the mechanical and durability characteristics analyzed. As for the light transmittance, it was attributed that the statistical difference between the fiber arrangements only within the 5% POF content can be a consequence of their accumulation in certain points of the material, thus influencing this characteristic measured by a light meter.

In the past few decades, the use of agricultural waste has been increasing due to the increasing demand for sustainable materials. This paper aims to review the significance of agricultural waste as a type of wealth and its potential as an alternative material in the composite field. It was found that many agricultural wastes had been utilized in various production of ecological products. The review discusses the physical, mechanical, and chemical properties of the natural fibers made from agricultural waste and the use of Pineapple Leaf Fiber Reinforced Composite to manufacture UAVs (Unmanned Aerial Vehicles). The extracted waste fibers’ physical, mechanical, and chemical properties show that these agricultural wastes can produce better advanced composite materials suitable for structural applications. The use of pineapple leaf fiber in Unmanned Aerial Vehicles manufacturing has the potential to revolutionize this industry and contribute to a more sustainable future.

A total internal reflection photonic crystal fiber (PCF) based on hexagonal core is proposed for gas sensing in a specific wavelength range. The higher sensitivity and lower confinement loss were realized by the structure of the proposed PCF consists of two layers with circular holes rotated hexagonally around a core region and six slotted air-hole in the cladding based on numerical analysis. The simulation results show that the enhancement of the relative sensitivity has been done by enhancing the diameter of the hexagonal shape air-hole cladding (d1) and the hexagonal arranged holes around the central solid core (d0) in this design. Also, the confinement loss has been reduced by enhancing the ratio of length to width of slotted holes (l/w) and decreasing the cladding air-hole diameters (d1). As the refractive index increases, the wavelength shifts toward the long wavelength. And in a certain temperature range, the transmission characteristics of the device does not change with the temperature. The results are helpful for designing high performance PCF for gas sensing applications.

In this study, fibers were extracted from different parts of the okra plant (Abelmoschus esculentus) via water- and dew-retting methods. The fibers were subjected to physical and thermal analyses. The fibers obtained from the upper part of the okra plant show higher breaking strength and lower linear density. Fibers obtained via water-retting exhibited higher breaking strength, elongation at break rates, and lower linear density values. The paper also presents the results of thermogravimetric analysis of the okra fibers. Tests were carried out in oxygen and inert gas atmospheres. The temperature range of the main thermal decomposition stage was in the 275–400°C for range thermo-oxidation and 300–425°C for pyrolysis investigation. Slight differences were found in the thermal resistances of the tested fibers, which was confirmed by an analysis using the alpha s- alpha r methodology. The calculated activation energy values show a large-spread range.

Fiber reinforced polymer (FRP) is one of the important material used for strengthening and retrofitting of reinforced concrete structures. The commonly used fibers are glass, carbon and aramid fibers. Durability of structures can be extended by selecting appropriate method of strengthening. FRP wrapping is one of the easiest methods for repair, retrofit and maintenance of structural element. Deterioration of structures may be due to moisture content, salt water, or contact with alkali solutions. There is significant effect of permeability, rise in temperature, chemical attack, fatigue action, micro pores on members of structures. Using FRP additional strength can be gained by structural elements. This paper investigates durability of aramid fiber subjected to acid attack and temperature rise. Concrete cubes are prepared as specimens with double wrapping of aramid fibers. Diluted hydrochloric acid solution is used for immersion of specimen for curing period of 7, 30 and 70 days. In case of fire resistance test, such specimens are kept in hot air oven at a temperature of 2000C at different time intervals. The effect of aramid fiber wrapping on compressive strength and weight loss of specimen is studied.

Thermal plasma is a versatile technology that can be used to treat various types of wastes, including vegetal and mineral oils, solvents, plastics, papers and cardboard, glasses, bricks and rocks, metals, clothes, and mixtures of these materials. In this study, we utilized a commercial plasma cutter as a thermal plasma source to decrease the volume of a simulated low-level radioactive mixed solid waste. The simulated waste included papers, plastics, clothes, gloves, metals and stable Co, Cs, Sr, and Ce additives as surrogates of 60Co, 137Cs, 90Sr, and 144Ce, the latter typical contaminants in nuclear LLW. As a result of the process two products were obtained, a solid phase in which we focused this work and a gaseous phase. To retain as much as possible surrogates in the solid final phase, crushed glass from broken bottles was included as a vitrification additive to the original waste. After undergoing heat treatment, a dense vitreous slag was produced and ashes. The process resulted in a volume reduction of 70%, indicating the successful gasification of organic excess materials. The surrogate elements were retained in the process and were found in the ashes composition: Co (3.4% w/w), Cs (37.7% w/w), Ce (0.6% w/w) and in the glass matrix composition of Co, Cs, Sr and Ce: 72.4 ± 14.7, 32 ± 18.2, 125.3 ± 31.6, 80 ± 13.1 % w/w respectively. For the actual experimental conditions, retention efficiencies were estimated for Cobalt (Co) at 72.4 ± 14.7%, Cerium (Ce) at 80 ± 13.1%, Strontium (Sr) at 125.3 ± 31.6%, and notably Cesium (Cs) at 32 ± 18.2%.

Glass has emerged as a highly versatile substrate for various sensor and MEMS packaging applications, including electromechanical, thermal, optical, biomedical, and RF devices, due to its exceptional properties such as high geometrical tolerances, outstanding heat and chemical resistance, excellent high-frequency electrical properties, and the ability to be hermetically sealed. In these applications, Through-Glass-Via (TGV) plays a vital role in manufacturing and packaging by creating electrical interconnections through glass substrates. This paper provides a comprehensive summary of the research progress in TGV fabrication along with their integrations, including through-via formation and metallization. The paper also reviews the significant qualification and reliability achievements obtained by the scientific community for TGV. Additionally, the paper summarizes the application of TGV technology in various sensors.

Understanding of the correlation between the magnetomechancial coupling factors (k) and damping factors (Q^-1) is a key pathway to enhance the magnetomechanical power conversion ef-ficiency in laminated magnetoelectric (ME) composites by engineeringly manipulating the magnetic and mechanical properties of Fe-based amorphous metals. The k and Q^-1 factors of FeSiB amorphous ribbons annealed in air at different temperatures are investigated. It is found that k and Q^-1 factors are affected by both magnetic and elastic properties. The magnetic and elastic properties are equalized in terms of the magnetomechanical power efficiency for the low temperature annealing. The k and Q^-1 of FeSiB-based epoxied laminates with different stacking numbers show that the -3 dB bandwidth and Young’s modulus are equalized in terms of the magnetomechanical power efficiency for the high lamination stacking.

Facade elements are known to represent a building component with multiple performance parameters to satisfy. Among others, “advanced facades” take advantage of hybrid solutions, like the assemblage of laminated materials. In addition to enhanced mechanical properties that are typical of optimally composed hybrid structural components, these systems are energy-efficient, durable, and offer lightening comfort and optimal thermal performance. This is the case of the structural solution developed in joint research efforts of the University of Zagreb and the University of Ljubljana, within the Croatian Science Foundation VETROLIGNUM project. The design concept involves the mechanical interaction of timber and glass load-bearing members, without sealing or bonded glass-to-timber surfaces. Laminated glass infilled timber frames are recognized as a new generation of structural members with relevant load-carrying capacity (and especially the enhancement of earthquake resistance of framed systems), but also energy-efficient and cost-effective solutions.

The use of natural fibres is investigated in recent years in cement, lime or geopolymer mortars to increase their toughness, resistance, tensile strength and durability. These fibres, derived from sources such as jute, hemp, sisal, and flax, are added to the mortar mix to enhance its mechanical properties and reduce cracking. The choice of the natural source strongly depends on local availability of the plant, its use and harvesting. In this paper the fibres of Diss (Ampelodesmos Mauritanicus, Poir) were used as reinforcement for mortars prepared by using waste materials, such as waste glass powder and air hardening lime obtained by the kilning of marble slurry. The samples underwent artificial and natural ageing and were characterized by measuring apparent density, water sorption coefficient, compression and bending stress, indicating a positive role of fibres addiction in increasing mortars durability.

Forensic assessments may involve the sampling of textile fibers when examining crime scenes. The need to characterize and identify those fibers is crucial as they can provide extensive information relating to a crime, linking a suspect to a location. Fibers in particular may contain issues in terms of both size and quantity of sample, and micro Fourier transform Infrared in attenuated total reflectance mode (micro FTIR-ATR) spectroscopy presents a non-destructive method to identify those fibers. In this study we carried out a rapid forensic assessment via micro FTIR-ATR of sixty textile fibers recovered from twenty white fabrics relying on tape lifting method, in order to discriminate those materials. Two dimensional principal component analysis and radar chart were applied to enhance the visual comparison of the fibers. Results of infrared spectra revealed that the technique allows the discrimination of textile fibers according to their spectral composition (cellulose, polyamide, polyester, or mixture of these composites) and to some characteristics, as number and width of peaks, peak position according to the wavenumber, absorbance index related to peak sharpness, etc. The technique was deemed useful in the forensic assessment of the fibers, presenting rapid and enlightening results.

We study impact of geometry on leakage loss in negative curvature fibers made with As₂Se₃ chalcogenide and As₂Se₃ chalcogenide glasses for carbon dioxide (CO₂) laser transmission. The minimum leakage loss decreases when the core diameter increases both for fibers with six and for fibers with eight cladding tubes. The optimum gap corresponding to the minimum loss increases when the core diameter increases for negative curvature fibers with six cladding tubes. For negative curvature fibers with eight cladding tubes, the optimum gap is always less than 20 μm when the core diameter ranges from 300 μm to 500 μm. The influence of material loss on fiber loss is also studied. When material loss exceeds 10² dB/m, it dominates the fiber leakage loss for negative curvature fiber at a wavelength of 10.6 μm.

The interfacial interface between the fibers and the matrix plays a key role for epoxy matrix composites and short recycled randomly arranged fibres. This study used short recycled carbon fiber (RCF) as a filler. Plasma treatment was used for carbon fiber surface treatment. This treat-ment was performed using radio (RF) and microwave (MW) frequencies at the same pressure and atmosphere. Appropriate chemical modification of the fiber surfaces helps to improve the wettability of the carbon fibers and, at the same time, allows the necessary covalent bonds to form between the fibers and the epoxy matrix. The effect of the plasma treatment was analyzed and confirmed by XPS analysis, Raman microscopy, SEM, TEM and wettability measurements. Composite samples filled with recycled carbon fibers with low concentrations (1 wt%, 2.5 wt% and 5 wt%) and high concentrations (20 wt% and 30 wt%) were made from selected treated fi-bers. The mechanical properties (impact toughness, 3PB) were analyzed on these samples. It was found that the modulus of elasticity and bending stress increase with the increasing content of recycled carbon fibers. A more significant change in impact strength occurred in samples with low concentration.

Crystallization of glass through conventional thermal annealing in a furnace is a well-understood process. However, crystallization by femtosecond (fs) laser brings another dimension to this process. The pulsed nature of the irradiation necessitates a reevaluation of parameters for optimal crystallization and to understand the particularities in the case of using fs laser. This includes adjusting the laser pulse energy, the repetition rate, and the writing speed to either initiate nucleation or achieve substantial crystal growth. Therefore, a key challenge to this work is to establish reliable calculations for understanding the relation of the size of the crystallized region with respect to an ongoing transition (e.g., solid-to-solid, liquid-to-solid), and accounting for the aforementioned laser parameters. In this context and based on previous work, we simulate a temperature distribution (in space and time) to model the thermal treatment at any point in the glass. By setting the condition that the temperatures are between the glass transition and melting temperature, we can deduce the crystallized region size to be compared with experimental observations. For that purpose, the knowledge of the beam width at the focal point and of the absorbed beam energy fraction are critical inputs that were extracted from experiments found in the literature. After that, management of the crystallization process and the width of the crystallization line can be achieved according to pulse energy e.g. crystallite size, and also the effect of the scanning speed can be understood. Among the main conclusions to highlight, we disclose the laser conditions that determine the extent of the crystallized area and deduce that it is never interesting to increase the pulse energy too much but rather the repetition rate for uniform crystallized line.

The recycling of common soda-lime glass (SLG) is far from being complete, since the material may contain small polymeric, metallic and ceramic contaminations. This has a negative impact on the quality of new glass articles prepared via re-melting. Alternatively, the full reuse of contaminated cullets could be achieved by low-temperature consolidation into geopolymer-like materials. SLG powders, used either as received or pre-washed in acid solution, were added to a sodium aluminate solution at the room temperature for 3 h, under low-speed mechanical stirring. Microporous semi-crystalline monoliths were formed by the casting of suspensions in plastic molds and cured at 75°C overnight. The monoliths featured hydrosodalite as the main crystalline phase for as received SLG and LTA zeolite in the case of pre-washed SLG. The mechanical properties compared well with those of cementitious materials. Moreover, by addition of coarse glass particles as fillers, the methodology successfully yielded Venetian terrazzo-like samples, which could lead to significant material and energy savings in their manufacture. The proposed approach could also be extended to other difficult-to-reuse glass formulations and provide attractive and versatile up-cycled materials.

The biomimetic design of engineering structures is based on biological structures with excellent mechanical properties, which are the result of billions of years of evolution. However, current biomimetic structures, such as ordered lattice materials, are still inferior to many biological materials in terms of structural complexity and mechanical properties. For example, the structure of \textit{Euplectella aspergillum}, a type of deep-sea glass sponge, is an eye-catching source of inspiration for biomimetic design; however, guided by scientific theory, how to engineer structures surpassing the mechanical properties of \textit{E. aspergillum} remains an unsolved problem. The lattice structure of the skeleton of \textit{E. aspergillum} consists of vertically, horizontally, and diagonally oriented struts, which provide superior strength and flexural resistance compared with the conventional square lattice structure. Herein, the structure of \textit{E. aspergillum} was investigated in detail, and by using the theory of elasticity, a lattice structure inspired by the bionic structure was proposed. The mechanical properties of the sponge-inspired lattice structure surpassed the sponge structure under a variety of loading conditions, and the excellent performance of this configuration was verified experimentally. The proposed lattice structure can greatly improve the mechanical properties of engineering structures, and it improves strength without much redundancy of material. This study achieved the first surpassing of the mechanical properties of an existing sponge-mimicking design. This design can be applied to lattice structures, truss systems, and metamaterial cells.

A novel stationary phase for affinity separations is presented. This material is based on sintered borosilicate glass readily available as semi-finished filter plates with defined porosity and surface area. The material shows fast binding kinetics and excellent long-term stability under real application conditions due to lacking macropores and high mechanical rigidity. The glass surface can be easily modified with standard organosilane chemistry to immobilize selective binders or other molecules used for biointeraction. In this paper, the manufacturing of the columns and their respective column holders by 3D printing is shown in detail. The model system protein A/IgG was chosen as an example to examine the properties of such monolithic columns under realistic application conditions. Several specifications, such as (dynamic) IgG capacity, pressure stability, long-term performance, productivity, non-specific binding, and peak shape, are presented. It could be shown that due to the very high separation speed, 250 mg antibody per hour and column can be collected, which surpasses the productivity of most standard columns of the same size. The total IgG capacity of the shown columns is around 4 mg (5.5 mg/mL), which is sufficient for most tasks in research laboratories. The cycle time of an IgG separation can be less than 1 minute. Due to the glass material's excellent pressure resistance, these columns are compatible with standard HPLC systems. This is usually not the case with standard affinity columns, limited to manual use or application in low-pressure systems. The use of a standard HPLC system also improves the ability for automation, which enables the purification of hundreds of cell supernatants in one day. The sharp peak shape of the elution leads to an enrichment effect, which might increase the concentration of IgG by a factor of 3. The final concentration of IgG can be around 7.5 mg/mL without the need for an additional nanofiltration step. The purity of the IgG was > 95% in one step and nearly 99% with a second polishing run.

Finely ground glass has the potential for pozzolanic reactivity and can serve as a supplementary cementitious material (SCM). Glass reaction kinetics depends on both temperature and glass composition. Microstructural modeling is a helpful approach to get better understanding of cement hydration and microstructure development. Mechanical and performance properties of concrete are directly related to the development of concrete microstructure, which is the consequence of progress in cement hydration. This study initially provides a comprehensive background about cement hydration process and microstructural modeling of the hydration. It then utilizes results of experimental studies, i.e. isothermal calorimetry and thermogravimetric analysis, to find kinetics equation parameters called “Avrami Constants”. For the first time, these constants were found for three main components of cement, i.e. C₃S, C₂S, and C₃A, and also for glass particles smaller than 25 µm. Although modeling of cement hydration and cementitious systems containing single glass particles showed promising results, simulations of combined glass types and sizes showed that more work on microstructural models is needed to properly model the reactivity of mixed glass particle systems.

Thermoplastic pultrusion is a suitable process for fabricating continuous unidirectional thermoplastics with a uniform cross-section, high mechanical properties due to continuous fiber reinforcement, low cost, and suitability for mass production. In this paper, jute and glass fibers were reinforced with a polypropylene matrix and fabricated using the thermoplastic pultrusion process. The volumetric fraction of the composite was designed by controlling the filling ratio of the reinforcing fiber and matrix. The effects of molding parameters were investigated, such as pulling speed and molding temperature, on the mechanical properties and microstructure of the final rectangular profile composite. The pulling speed and molding temperature were varied from 40 to 140 mm/min and 190 to 220°C, respectively. The results show that an increase in molding temperature initially led to an increase in mechanical properties, up to a certain point. Beyond that point, they started to decrease. The increase in molding temperature also led to an increase in void content. Meanwhile, un-impregnation decreased with the increase in molding temperature, and the jute fiber began to degrade at high temperatures. In the next step, with varying pulling speed, the mechanical properties decreased as the pulling speed increased, with a corresponding increase in void content and un-impregnation. The decrease in mechanical properties was influenced by the increase in void content and un-impregnation, as the jute fiber degraded at higher temperatures.

Biomedical implants are the need of this era due to the increase in number of accidents and follow-up surgeries. Different types of bone diseases such as osteoarthritis, osteomalacia, bone cancer, etc. are increasing globally. Mesoporous bioactive glass nanoparticles (MBGNs) are used in biomedical devices due to their osteointegration and bioactive properties. In this study, silver (Ag) and strontium (Sr) doped mesoporous bioactive glass nanoparticles (Ag-Sr MBGNs) were prepared by a modified Stöber process. In this method, Ag+ & Sr2+ were co-substituted in pure MBGNs to harvest the antibacterial properties of Ag ions, as well as pro-osteogenic potential of Sr2 ions. The effect of the two ion concentration on morphology, surface charge, composition, antibacterial ability, and in-vitro bioactivity was studied. Scanning electron microscopy (SEM), X-Ray diffraction (XRD) and Fourier transform infrared spectroscopy (FTIR) confirmed the doping of Sr and Ag in MBGNs. SEM and EDX analysis confirmed the spherical morphology and typical composition of MBGNs, respectively. The Ag-Sr MBGNs showed a strong antibacterial effect against Staphylococcus carnosus and Escherichia coli bacteria determined via turbidity and disc diffusion method. Moreover, the synthesized Ag-Sr MBGNs develop apatite-like crystals upon immersion in simulated body fluid (SBF), which suggested that the addition of Sr improved in-vitro bioactivity. The Ag-Sr MBGNs synthesize in this study can be used for the preparation of scaffolds or as a filler material in the composite coatings for bone tissue engineering.

(1) Background: Little is known about the baroque composer Domenico Scarlatti (1685-1757), whose life was centred behind closed doors at the royal court in Spain. There are no reports about his illnesses. From his compositions, mainly for harpsichord, an outstanding virtuosity can be read. (2) Case Presentation: In this case report, the only known oil painting of Domenico Scarlatti is presented, on which he is about 50 years old. In it one recognizes conspicuous hands with hints of watch glass nails and drumstick fingers. (3) Discussion: Whether Scarlatti had chronic hypoxia of peripheral body regions as a sign of, e.g., bronchial cancer or a severe heart disease, is not known. (4) Conclusions: The above-mentioned signs recorded in the oil painting, even if they were not interpretable at that time, are clearly represented and recorded for us and are open to diagnostic discussion from today's point of view.

In this paper, design of optical spectral filters based on mode coupling of optical fibers is presented. The finite difference method is applied to find the dispersion characteristics of optical fiber coupler constructing from two fibers as a composite multi-dielectric waveguide with different cores but the same cladding. Also, the field distribution for both fibers as a separate and as a composite waveguide. The spectral characteristics of the filters are investigated depending on the coupling of two linear polarized modes LP01 and LP11. The dependence of the transmission coefficient on operating wavelengths is illustrated. Finally, the spectral bandwidth of filter as a function of the distance between the two cores is addressed.

This study aimed to investigate Coll-I, III, IV and elastin in canine normal prostate and PC, using Picrosirius red (PSR) and Immunohistochemical (IHC) analysis. Eight normal prostates and 10 PC from formalin-fixed, paraffin-embedded samples were used. Collagen fibers area was analyzed with ImageJ software. The distribution of Coll-I and Coll-III was approximately 80% around prostatic ducts and acini, 15% among smooth muscle and 5% surrounding blood vessels, in both normal prostate and PC. There was a higher median area of Coll-III in PC, when compared to normal prostatic tissue (p=0.001 for PSR and p= 0.05 for IHC). Immunostaining for Coll-IV was observed in the basal membrane of prostate acini, smooth muscle, blood vessels, and nerve fibers of normal and PC samples. Although there was no difference in Coll-IV area between normal tissue and PC, tumors with Gleason score 10 showed absence of Coll-IV, when compared to scores 6 and 8 (p=0.0095). Elastic fibers were found in the septa dividing the lobules and around the prostatic acini of normal samples, and was statistically higher in PC, compared to normal tissue (p=0.00229). Investigation of ECM components brings new information and should be correlated with prognosis in future studies.

Composite biomaterials that combine osteoconductive and osteoinductive properties are a promising approach for bone tissue engineering (BTE) since it allows osteogenesis stimulation while mimicking the extracellular matrix (ECM) morphology. In this context, the aim of the present research work was to produce polyvinylpyrrolidone (PVP) nanofibers containing mesoporous bioactive glass (MBG) 80S15 nanoparticles. These composite materials were produced by electrospinning technique. The design of experiments (DOE) was used to estimate the optimal electrospinning parameters to reduce average fiber diameter. The polymeric matrices were thermally crosslinked under different conditions, and the fiber’s morphology was studied using scanning electron microscopy (SEM). Evaluation of the mechanical properties of nanofibrous mats revealed a dependence on thermal crosslinking parameters and on the presence of MBG 80S15 particles inside the polymeric fibers. Degradation tests indicated that the presence of MBG led to a faster degradation of nanofibrous mats. On the other hand, MBG presence also leads to higher swelling capacity. The assessment of in vitro bioactivity in simulated body fluid (SBF) was performed in MBG pellets and PVP/MBG (1:1) composites to assess whether the bioactive properties of MBG 80S15 were kept when it was incorporated into PVP nanofibers. FTIR and XRD analysis along with SEM–EDS results indicated that a hydroxy-carbonate apatite (HCA) layer was formed on the surface of MBG pellets and nanofibrous webs after soaking in SBF over different time periods. In general, the materials revealed no cytotoxic effects on Saos-2 cell line. The overall results for the produced materials show the potential of the composites to be used in BTE.

The on-site wastewater treatment system (OWTS) with a sand trench is an economical option for residents in rural areas or the countryside where a centralised sewer system is inaccessible. 2A sand achieves improved filtration, microbial activity and consistent long term performance when compared to gravel or scoria based trench systems. However, it is expensive and only readily available in a few areas across New Zealand. Additionally, it has a reputation for premature blockage when overloaded or compacted. The aim of this study is not only to critically evaluate the performance of Crushed Glass (CG) with respect to 2A sand, but also to investigate different loading rates for CG when treating primary treated effluent from a septic tank. A test rig was designed and constructed to simulate the real environment of the sand column in a discharge control trench. The treatment efficiency of three filters was recorded and compared in this study. Overall, the CG loaded at 25mm/day (CG₂₅) and 50mm/day (CG₅₀) provided an average of 13% and 6% more Total Nitrogen (TN) reduction than the sand filter, respectively. The removal rates for the TN were up to 69.5%. The CG₅₀ filter performed similarly at 50mm/day as the 2A sand filter in terms of Total Suspended Solids (TSS) and Biochemical Oxygen Demand (BOD)₅ removal of more than 94%. The CG₂₅ removal rates for TSS and BOD₅ at the start of the trial (likely due to residual liquid contamination from the bottles when crushed) improved over the sampling period and ultimately achieved similar results of 92% and 91.3% to the filters loaded at 50mm/day. Lifecycle cost analyses and carbon balances were completed for the two media. It highlighted that the current price of CG is only half of 2A sand, yet it produces significantly less CO₂ emissions than 2A sand. A 3-bedroom dwelling could save up to $500 and reduce 200kg of CO₂ released to the environment annually when 2A sand is substituted for CG. Based on the findings of this paper, it is likely that the reduced installation cost, lessened environmental impact and theoretical availability will lead to CG systems becoming more common in New Zealand and abroad.

In this paper, we present a preliminary study and conceptual idea concerning 3D printing water-sensitive glass by exemplifying with a borosilicate glass with high alkali and alkaline oxide contents using direct ink writing. The investigated material was prepared in the form of a glass frit, which was further ground in order to obtain a fine powder of desired particle size distribution. In a following step, inks were prepared by mixing the fine glass powder with Pluoronic F-127 hydrogel. The acquired pastes were rheologically characterized and printed using a Robocasting device. DSC experiments were performed for base materials and the obtained green bodies. After sintering, SEM and XRD analyses were carried out in order to examine microstructure and the eventual presence of crystalline phase inclusions. Results confirmed that obtained inks exhibit stable rheological properties despite the propensity of glass to undergo hydrolysis and could be adjusted to desirable values for 3D printing. No additional phase was observed, supporting the suitability of the designed technology for the production of water sensitive glass inks. SEM micrographs of the sintered samples revealed the presence of closed porosity, which may be the main reason of light scattering.

Fabrication of a true-3D inorganic ceramic with resolution down to nanoscale using sol-gel resist precursor is demonstrated. The method has an unrestricted free-form capability, control of the fill-factor, and high fabrication throughput. A systematic study of the proposed approach based on ultrafast laser 3D lithography of organic-inorganic hybrid sol-gel resin followed by a heat treatment enabled formation of inorganic amorphous and crystalline composites guided by the composition of the initial resin. The achieved resolution of 100 nm was obtained for 3D patterns of complex free-form architectures. Fabrication throughput of 50×10³ voxels/s is achieved; voxel - a single volume element was recorded by a single pulse exposure. After a subsequent thermal treatment, ceramic phase was formed depending on the temperature and duration of the heat treatment as validated by Raman micro-spectroscopy. The X-ray diffraction (XRD) revealed a gradual emergence of the crystalline phases at higher temperatures with a signature of cristobalite SiO₂, a high-temperature polymorph. Also, the tetragonal ZrO₂ phase known for its high fracture strength was observed. This 3D nano-sintering technique is scalable from nano- to millimeter dimensions and opens a conceptually novel route for optical 3D nano-printing of various crystalline inorganic materials defined by an initial composition for diverse applications for microdevices in harsh physical and chemical environments and high temperatures.

In the application of classical nucleation theory (CNT) and all other theoretical models of crystallization of liquids and glasses it is always assumed that nucleation proceeds only after the supercooled liquid or the glass have completed structural relaxation processes towards the metastable equilibrium state. Only employing such assumption, the thermodynamic driving force of crystallization and the surface tension can be determined in the way it is commonly performed. The present paper is devoted to the theoretical treatment of a different situation when nucleation proceeds concomitantly with structural relaxation. To treat the nucleation kinetics theoretically for such cases, we need adequate expressions for the thermodynamic driving force and the surface tension accounting for the contributions caused by the deviation of the supercooled liquid from metastable equilibrium. In the present paper, such relations are derived. They are expressed via deviations of structural order parameters from their equilibrium values. Relaxation processes result in changes of the structural order parameters with time. As a consequence, the thermodynamic driving force and surface tension, and basic characteristics of crystal nucleation, such as the work of critical cluster formation and the steady-state nucleation rate, also become time-dependent. We show that this scenario may be realized in the vicinity and below the glass transition temperature, and it may occur only if diffusion (controlling nucleation) and viscosity (controlling the alpha-relaxation process) in the liquid decouple. Analytical estimates are illustrated and confirmed by numerical computations for a model system. The theory is successfully applied to the interpretation of experimental data. Several further consequences of this newly developed theoretical treatment are discussed in detail. In line with our previous investigations, we reconfirm that only when the characteristic times of structural relaxation are of similar order of magnitude or longer than the characteristic times of crystal nucleation, elastic stresses evolving in nucleation may significantly affect this process. Completing the analysis of elastic stress effects, for the first time expressions are derived for the dependence of the surface tension of critical crystallites on elastic stresses. As the result, a comprehensive theoretical description of crystal nucleation accounting appropriately for the effects of deviations of the liquid from the metastable states and of relaxation on crystal nucleation of glass-forming liquids, including the effect of simultaneous stress evolution and stress relaxation on nucleation, is now available. As one if its applications, this theoretical treatment provides a new tool for the explanation of the low-temperature anomaly in nucleation in silicate and polymer glasses (the so-called \breakdown" of CNT at temperatures below the temperature of the maximum steady-state nucleation rate). We show that this anomaly results from much more complex features of crystal nucleation in glasses caused by deviations from metastable equilibrium (resulting in changes of the thermodynamic driving force, the surface tension, and the work of critical cluster formation, in the necessity to account of structural relaxation and stress effects) than assumed so far.

Cocoa bean shells (CBSs) represent the external layer of cocoa beans. The shells are removed during the winnowing after the pre-roasting, a processing step of chocolate production; in in the past they were considered a waste. CBSs possess many interesting nutritional characteristics in both macro and micronutrients. CBSs result very rich in dietary fiber and antioxidant compounds such as phenolic acids and flavan-3-ols. Soluble dietary fibers are potentially associated with fermentability and prebiotic activity on human gut microbiota instead antioxidants compounds have been linked with positive effects on human health. Based on these properties, the aim of this study was the valorization of CBSs thorough enzymatic treatments. The shells were treated both raw and defatted; three sets of carbohydrases have been used in order to destructure the fiber profile, potentially enhancing the potential prebiotic activity of CBSs. Cellulase, xylanase and pectinase were used to perform enzymatic treatments. After the enzymatic hydrolisis, both soluble and insoluble fibers fraction were quantified, in parallel with the total phenolic and the total flavonoid contents and the antioxidant activity. Moreover, the HPLC-PDA analysis was carried out for the main compounds of CBSs. The enzymatic treatmens allowed to obtain an enhancement in soluble fibers, for both defatted and raw CBSs, particularly using cellulase, xylanase and their combinations. Finally, a parallel preservation of the antioxidant capacity and the content of the main bioactive compounds after the treatments was observed. These results can be used to exploit the enzymatic treated CBSs to further industrial applications in the food and nutraceutical fields.

The global textile sector, pivotal to economic development, significantly contributes to environmental degradation, prompting a shift towards sustainable raw material sources. Embracing circular economy principles, this industry is exploring the valorization of agricultural by-products. This study introduces an innovative approach to repurposing mango waste into valuable textile fibers, a byproduct of the fruit processing industry, predominantly generated during juice and jam production. The focus is on the lignocellulosic constituents of mango waste, specifically the peel, seed, and fibrous material, traditionally considered as refuse. Previous research has predominantly utilized mango peel in pectin extraction for food applications, whereas the potential of seed and fibrous content remains underexplored. This investigation endeavors to transform these fibrous by-products into high-value materials suitable for textile manufacturing. The process involved washing, drying, and comprehensive physicochemical characterization of mango fibers, emphasizing lignin quantification, revealing a composition of 12.2% lignin. An experimental design was employed to elucidate the impact of variables such as liquid-to-solid ratio, reaction duration, and sodium hydroxide concentration on lignin dissolution through alkaline hydrolysis. Optimal conditions—10% NaOH concentration, 30 mL/g liquid-to-solid ratio over six hours—achieved an 83% reduction in lignin content. The resulting fibers exhibited properties akin to conventional natural fibers, including a favorable aspect ratio indicative of their suitability for textile applications. A subsequent softening process using propylene glycol enhanced the fibers' spinability, producing a durable, textured fabric ideal for eco-conscious fashion applications, including bags, footwear, and accessories. This research demonstrates the feasibility of converting mango waste into a textile-worthy material and underscores the importance of waste revalorization in promoting sustainability within the circular economy framework.

The electrical, mechanical and thermal conductivity of ethylene butene copolymer (EBC) composites with carbon fibers were studied. EBC/carbon-fiber composites can be utilized as an electro-mechanical material which is capable of changing it electric resistance with mechanical strain. Carbon fibers were introduced to EBC with different concentrations (5-25 wt%). The results showed that the addition of carbon fibers to EBC could increase the electric resistance up to 10 times. Increasing the load to 2.9 MPa could increase the electric resistance change by 4500% compared 25% fiber sample with pure EBC. It is also noted that the electric resistance of the EBC/CF composites underwent a dramatic increase with raising the strain, for example, the resistance change was around 13 times more at 15% strain in comparison to 5% of strain; The thermal conductivity tests showed that the addition of carbon fibers could increase the thermal conductivity by 40%, from 0.19 to 0.27 (Wm-1K-1). It was also observed that the addition of carbon fibers to EBC could increase the thermal conductivity.

Fabrics comprised of porous fibers could provide effective passive protection against chemical and biological (CB) threats whilst maintaining high air permeability (breathability). Here, we fabricate hierarchically porous fibers consisting of regenerated silk fibroin (RSF) and activated-carbon (AC) prepared through two fiber spinning techniques in combination with ice-templating – namely cryogenic solution blow spinning (Cryo-SBS) and cryogenic wet-spinning (Cryo-WS). The Cryo-WS RSF fibers had exceptionally small macropores (as low as 0.1 µm) and high specific surface areas (SSAs) of up to 79 m2 g-1. The incorporation of AC could further increase the SSA to 210 m2 g-1 (25 wt. % loading) whilst also increasing adsorption capacity for volatile organic compounds (VOCs).

The effect of γ-ray irradiation on surface plasmon resonance (SPR) sensing capability of refractive index (n = 1.418–1.448) of the silica glass optical fiber comprised of germano-silicate glass cladding embedded with Au nano-particles (NPs) was investigated. As the γ-ray irradiation increased from 1 hour to 3 hours with the dose rate of 1,190 Gy/h, the morphology of the Au NPs and the SPR spectrum were found to change. The average diameter of Au NPs increased with the aspect ratio from 1 to 2 and the nano-particles became grown to the clusters. The SPR peak wavelength shifted towards longer wavelength with the increase of total dose of γ-ray irradiation regardless of the corresponding refractive indices. The SPR sensitivities (wavelength/refractive index unit, nm/RIU) also increased from 407 nm/RIU to 3,553 nm/RIU, 1,483 nm/RIU, and 2,335 nm/RIU after the γ-ray irradiation at the total dose of 1,190 Gy, 2,380 Gy, and 3,570 Gy, respectively.

Background: We investigated the effect of bioactive glass and zinc oxide nanoparticles on enamel remineralization, as well as their antibacterial effect on cariogenic bacteria. Methods: Fluoride gel (F), bioactive glass microparticles (µB), bioactive glass nanoparticles (nB), zinc oxide nanoparticles (Z), and a mixed suspension of nB and Z (nBZ) were prepared and subjected to the following tests: morphological evaluation by scanning and transmission electron microscopy, measurement of specific surface area, zeta potential measurement, crystal structure analysis by X-ray diffraction, and acid buffering capacity test. Further, we performed a remineralization cycle test of 28 days and a nanoindentation testing was carried out during the immersion period and then the enamel surfaces were examined using scanning electron microscopy. Additionally, the antibacterial effects of the sample suspensions were evaluated by measuring their minimum bactericidal concentrations against various cariogenic bacteria. Results: Our results revealed that nB had a near-circular shape with an amorphous structure, a considerably large specific surface area due to nanoparticulation. Additionally, nB possessed a rapid acid buffering capacity, which was comparable to that of μB. In the remineralization test, faster recovery of mechanical properties was observed on the enamel surface immersed in samples containing bioactive glass nanoparticles (nB and nBZ). After remineralization, demineralized enamel immersed in any of the samples showed a rough and porous surface structure covered with mineralized structures. Furthermore, nBZ exhibited a broad antibacterial spectrum. Conclusions: These results demonstrated that bioactive glass and zinc oxide nanoparticles have superior demineralization-suppressing and remineralization-promoting effects.

Sodium-phosphate-based glass-ceramics (GCs) are promising materials for a wide range of applications, including solid-state sodium-ion batteries, microelectronic packaging substrates, and humidity sensors. This study investigates the impact of 24-hour heat-treatments at varying temperatures on Na-Ge-P glass, with a focus on (micro)structural, electrical, and dielectric properties of prepared GCs. Various techniques such as powder X-ray diffraction (PXRD), infrared spectroscopy-attenuated total reflection (IR-ATR), and scanning electron microscopy-energy dispersive spectroscopy (SEM-EDS) are employed. With the elevation of heat-treatment temperature, crystallinity progressively rises; at 450 °C, the microstructure retains amorphous traits featuring nanometric grains, whereas at 550 °C, heat-treatment results in fully crystallized structures characterized by square-shaped micron-scale grains of NaPO3. The insight into the evaluation of electrical and dielectric properties is provided by Solid-State Impedance Spectroscopy (SS-IS), revealing a strong correlation with the conditions of controlled crystallization and observed (micro)structure. The glass-ceramic heat-treated at 450 °C achieves the highest DC conductivity of 2.30×10–8 Ω–1 cm–1 at 393 K. As the heat-treatment temperature rises, the crystallization of the NaPO3 phase depletes the glass matrix of mobile Na+ ions, resulting in a reduction in DC conductivity. Dielectric parameters also decrease with rising heat-treatment temperature, with the glass-ceramic heat-treated at 550 °C displaying the lowest permittivity of 19.37 and the dielectric loss of 0.008. This research uncovers the intricate relationship between heat-treatment conditions and material properties, emphasizing that controlled crystallization allows for precise modifications to microstructure and phase composition within remaining glassy phase, ultimately facilitating fine-tuning of material properties.

This study examines the impact of the impregnation of fireclay-based conventional (CC) and medium cement castables (MCC) with liquid sodium silicate glass under vacuum conditions. The goal is to assess how this treatment affects physical, mechanical properties, and durability (alkali and thermal shock resistance) of these castables used in biomass combustion boilers, where they are exposed to temperatures up to 1100°C. The research work employs standard test methods to evaluate physical and mechanical properties. Additionally, advanced techniques such as scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDS), X-ray diffraction (XRD), and specific tests for alkali resistance and thermal shock resistance are used. The research findings suggest that impregnation with sodium silicate glass under vacuum significantly enhances the alkali resistance of both CC and MCC castables. This improvement is primarily due to the reduction in porosity and the increase in density. SEM images reveal that impregnated samples are coated with a glassy layer and the pores are partially filled with sodium silicate. Tests for alkali resistance demonstrate the formation of a protective glassy layer (with a thickness of 0.9-1.5 mm) on the castables surfaces, thereby reducing further penetration of alkali into deeper layers of the samples. However, it is important to mention that impregnated refractory castables have reduced resistance to thermal shock cycles.

The rapid development of the photovoltaic (PV) industry will result in an increase in the amount of electrical and electronic waste from used PV panels. Only in Poland, the total capacity installed in photovoltaic sources in Poland in May 2020 exceeded 1,950 MW, and the installation weight was approximately 120,000. tone. The problem arises in the recycling or management of this waste. This work presents methods used to recycle waste into photovoltaic modules. The authors investigated the possibility of mechanical and chemical processing of crystalline silicon. A method of thermal treatment of the panel was also proposed. As a result of the research, it was found that the stage of separating materials (crystalline cream, EVO foil, aluminum frame) plays an important role in the recycling process, which is not easy. Chemical treatment allows the silicon to become plastic and the temperature melts the back layer of the panel.

Cu-Sn shape-memory microwires were fabricated by a glass-coated melt spinning method. Effects of Sn content on the microstructure and mechanical property of microwires were investigated. The phase transforms from martensite to austenite with Sn content increasing from 14.0 atomic percent (at.%) to 16.5 at.%, and highly ordered intermetallic phase, δ, formed with higher Sn content. The fracture stress, σf, and the critical stress for martensitic transformation, σMs, increases with Sn content increasing. The mechanical property as well as superelasticity were improved greatly by high cooling rate of the glass-coated melt spinning method.

In this study, we propose a solution process for realizing color glass for building integrated pho-tovoltaic (BIPV) systems by spin coating a color solution composed of a pearlescent pigment mixed in a norland optical adhesive (NOA) matrix. Color solutions are made from mixing pearlescent pigments in NOA63. Compared to a physical vapor deposition process, color coatings are achieved by spin coating in a relatively simple and inexpensive process at room temperature. The optical properties can be easily controlled by adjusting the spin coating speed and the concentra-tion of the pearlescent pigments. The produced color glasses achieved a high transmittance of 85% or more in the visible wavelength range, except the wavelength spectrum exhibiting the maxi-mum reflectance. In addition, we propose a one-step lamination process of color glass on a solar cell by leveraging on the adhesive property of the NOA matrix. This eliminates the cost and pro-cess of additional ethylene vinyl acetate (EVA) layer or other materials used in the conventional lamination process. The color glass produced through this study has stability that does not change its properties over time. Therefore, it is expected to be applied to the BIPV solar module market where aesthetics and energy efficiency are required.

Optinalysis, as a method of symmetry detection, is a new algorithm that intrametrically (within elements or variables) or intermetrically (between elements or variables) computes and compares two or more univariate or multi-clustered or multivariate sequences as a mirror-like reflection of each other (optics-like manner), hence the name is driven. Optinalysis is based by the principles of reflection and moment about a symmetrical line which detects symmetry that reflects a similarity measurement. This proposed methodology was validated in comparison with Pearson method of skewness detection, and also with some algorithms for pairewise alignment and comparison of genomic sequences (Needle, Stretcher, Water, Matcher) on EMBL-EBI website. A results comparison shows that optinalysis is more advance, more sensitive, more inferential and simple alternative approach of skewness detection and pairewise sequence comparison.

To elucidate dynamic developmental processes in plants, live tissues and organs have to be visualized frequently and for long time periods. The development of roots is studied in depth at a cellular resolution not only to comprehend the basic processes fundamental to maintenance and pattern formation but also study stress tolerance adaptation in plants. Despite technological advancements, maintaining continuous access to samples and simultaneously preserving their morphological structures and physiological conditions without causing damage presents hindrances in the measurement, visualization and analyses of growing organs including plant roots. We propose a preliminary system which integrates the optical real-time visualization through light microscopy with a liquid culture which enables us to image at the tissue and cellular level horizontally growing Brachypodium roots every few minutes and up to 24 hours. We describe a simple setup which can be used to track the growth of the root as it grows including the root tip growth and osmotic stress dynamics. We demonstrate the system’s capability to scale down the PEG-mediated osmotic stress analysis and collected data on gene expression under osmotic stress.

Kluyveromyces marxianus (K. marxianus) is a newly emerging industrially relevant yeast. It is known to possess a highly efficient Non-Homologous End Joining (NHEJ) pathway that promotes random integration of non-homologous DNA fragments into its genome. The nature of the integration events was traditionally analyzed by Southern blot hybridization. However, the precise DNA sequence at the insertion sites were not fully explored. We transformed a PCR product of the Saccharomyces cerevisiae URA3 gene (ScURA3) into an uracil auxotroph K. marxianus wildtype strain and picked 24 stable Ura+ transformants for sequencing analysis. We took advantage of rapid advances in DNA sequencing technologies and developed a method using a combination of Illumina MiSeq and Oxford Nanopore sequencing. This approach enables us to uncover the Gross Chromosomal Rearrangements (GCRs) that are associated with the ScURA3 random integration. Moreover, it will shine a light on understanding DNA repair mechanisms in Eukaryotes, which could potentially provide insights for cancer research.

Herein, the mechanical properties and carbonation durability of engineered cementitious composites (ECC) were studied. For cost-efficient utilization of ECC materials, polypropylene (PP) and hydrophilic polyvinyl alcohol (PVA) fibers were employed to cast different types of specimens. The compressive strength, Poisson’s ratio, strength-deflection curves, cracking/post-cracking strength, impact index, and tensile strain-stress curves of the two types of ECC materials, with different fiber contents of 0 vol%, 1 vol%, 1.5 vol% and 2 vol%, were investigated by conducting compressive tests, four-point bending tests, drop weight tests, and uniaxial tensile tests. In addition, the matrix microstructure and failure morphology of the fiber in the ECC materials were studied by scanning electron microscopy (SEM) analysis. Furthermore, carbonation test and steel corrosion after carbonization were employed to study durability resistance. The results indicated that for both PP fiber- and hydrophilic PVA fiber-reinforced ECCs, the compressive strength first increases and then decreases as fiber content increases from 0 vol% to 2 vol% and reaches the maximum at 1 vol% fiber content. The bending strength, deformation capacity, and impact resistance show significant improvement with increasing fiber contents. The ECC material reinforced with 2 vol% PP fiber shows superior carbonized durability with maximum carbonation depth of only 0.8 mm.

Gelatin fibers have a specific surface and high porosity, which is why their use in medicine and the food industry is being researched. This article explores the potential of centrifugal spinning to produce gelatin fibers. Gelatin for fiber preparation is obtained from a non-traditional source of collagen (chicken by-products) using a unique enzymatic process. The fiber quality is compared with those prepared from traditional collagen tissues (porcine, bovine). The results show that fibers crosslinked with glutaraldehyde vapor preserve their structure even in contact with water. Using a cross-linker controls swelling ability and solubility while maintaining the fiber structure. On the contrary, uncross-linked gelatin fibers are water soluble due to a high surface-to-volume ratio, facilitating water penetration and dissolution. Scanning electron microscopy (SEM) provided a clearer picture of the morphology of gelatin fibers obtained by centrifugal spinning. Differences in the amount of bonding depending on the raw material used and the presence of cross-linker were analyzed using Fourier transform infrared spectroscopy (FTIR). The overall results showed that chicken gelatin is a suitable alternative to gelatins from traditional sources.