In order to achieve global climate goals, it is necessary to estimate greenhouse gases (GHG) fluxes from ecosystems. To obtain a comprehensive assessment of CO2, СН4, N2O natural fluxes for the Russian Federation we used the "bottom-up" method according to [1]. We updated estimates for forest ecosystems based on State Forest Inventory data and satellite monitoring of forest disturbances. For grassland ecosystems, it was based on the correct distribution of areas between steppe and non-steppe zones. The estimated net uptake of natural ecosystems of Russia was 1.1 ± 1.8 billion tons of CO2-eq./year. The study shows that if only CO2 is taken into account, the net absorption of terrestrial ecosystems in Russia corresponds to more than -2.5 billion tons of CO2 (35% of forests’ contribution). However, given the emissions of non-CO2 GHGs, total net absorption in Russia’s natural ecosystems is reduced to about -1 billion tons of CO2-eq (with the forests’ contribution increasing to 80%). With regard to anthropogenic fluxes, the overall balance of GHGs in Russia corresponds to net-emissions of 1 billion tons of CO2-eq/year into the atmosphere. To improve reporting under the Paris Agreement, countries should aim to include only anthropogenic ("manageable") GHG fluxes on managed land.

Global coverage and scale up of interventions to reduce newborn mortality remains low, though progress has been achieved in improving newborn survival in many low-income settings. An important factor in the success of newborn health interventions, and moving to scale, is appropriate design of community-based programs and strategies for local implementation. We report the results of formative research undertaken to inform the design of a newborn health intervention in Cambodia. Information was gathered on newborn care practices over a period of three months using multiple qualitative methods of data collection in the primary health facility and home setting. Analysis of the data indicated important gaps, both at home and facility level, between recommended newborn care practices and those typical in the study area. The results of this formative research have informed strategies for behavior change and improving referral of sick infants in the subsequent implementation study. Collection and dissemination of data on newborn care practices from settings such as these can contribute to efforts to advance survival, growth and development of newborns for intervention research, and for future newborn health programming.

Solar photovoltaic (PV) generation suffers from multiple serious issues, for example shading effects directly affect the performance of installed PV arrays. By studying these issues, it can play a key role in improving the limitations and performance of PV panels. The study of PV arrays under partial shading conditions is mentioned in many papers as a part of other studies and as an independent phenomenon. Therefore, it is essential to improve these studies and update them with new research and study this problem in detail to know how to limit the effects of partial shading irradiance conditions on PV arrays performances, including economical aspects. This paper proposes to study the effects of different partial shading irradiance conditions for a PV array in various configurations. The analysis is proved in detail through the simulation of the proposed PV array in the Matlab/Simulink environment. The obtained results show the performances of interconnected PV arrays under different partial shading irradiance and temperature conditions, including the solar array I-V and P-V characteristics. In addition, different PV array configurations with and without bypass and blocking protection diodes improve and minimize the effect of partial shading conditions and avoid the reductions in output power.

Obesity poses significant challenges in rural communities worldwide due to limited resources and healthcare access. Practical, innovative, and culturally sensitive approaches are essential. Time-Restricted Eating (TRE), aligning food intake with circadian rhythms, emerges as a promising strategy. By restricting eating to specific time windows, TRE synchronizes with the body's internal clock, offering potential metabolic health benefits. This review examines TRE's potential in rural obesity management, highlighting its simplicity and scalability. While TRE may address rural health disparities, cultural considerations and challenges such as undernutrition must be acknowledged for effective implementation. Overall, TRE shows promise in improving metabolic health and well-being in rural populations.

Introduction: The academic landscape is increasingly recognizing the complex interplay of personal and professional responsibilities on scholarly productivity. For women scholars, particularly those with significant parenting duties, this balance is even more precarious. This study aims to explore how family responsibilities, personal vulnerabilities, and motivational theories such as Imposter Syndrome and Self-Determination Theory (SDT) influence the motivation to publish scholarly work. Understanding these dynamics is crucial for developing supportive mechanisms that can enhance academic productivity and personal fulfilment. Methods: Utilizing a Qualitative Evidence Synthesis (QES) framework, this study will systematically review and synthesize qualitative research on women scholars' experiences in academia, focusing on the challenges and motivators related to publishing. Data sources will include academic databases, grey literature, and first-hand narratives. Thematic analysis will be employed to identify key themes and patterns across the collected data. Results/Findings: Preliminary findings suggest that the dual demands of parenting—especially in extreme cases such as assuming responsibility for seven children—and academic work significantly impact women scholars' publishing activities. Personal vulnerabilities, including imposter syndrome and low self-efficacy, further exacerbate these challenges. However, the data also highlight resilience strategies and the potential for intrinsic and extrinsic motivational factors to mitigate these effects. Discussion: The study underscores the nuanced impact of familial and personal factors on academic motivation. The preliminary findings suggest that addressing imposter syndrome and enhancing self-determination could be pivotal in supporting women scholars. The role of institutional policies and academic culture in either exacerbating or alleviating these challenges is also discussed. Significance: By elucidating the specific challenges and motivators for women scholars in publishing, this study will contribute to the development of targeted interventions and policies that support work-life integration and promote academic productivity. The insights that will be gained could inform mentorship programs, institutional support systems, and policy reforms aimed at fostering a more inclusive and supportive academic environment.

In this article, we describe a simple procedure for evaluating the sterility of nutrient media using a shear-horizontal surface acoustic wave (SH-SAW) biosensor. We used the SH-SAW biosensor platform to monitor the time-dependent phase responses of the material for the media that binds to a monolayer of 3-mercaptopropanyl-N-hydroxy succinimide on the biosensor surface. Increases in the phase shift less than 50% of the starting phase shift recorded 180 minutes after the sterilization indicate a successful sterility test of the media. Our devices were then applied to sterility testing using a viable Escherichia coli (E. coli) K-12 solution to confirm our hypothesis. Filtered LB Broth was the negative control, and a 24-hour culture of E. coli was the positive control. Before testing, the cell solution was pelleted, the media decanted, and then replaced with a 1x phosphate-buffered saline solution (1x PBS). Since we know that the N-hydroxysuccinimide residues will bind to amine groups, only in cases where microbial species are present will the surface binding increase greater than 50%. We confirmed our hypothesis using SH-SAW biosensors and overnight E. coli cultures. The sensitivity for our 250 MHz quartz SH-SAW sensors was calculated based on the response from the E. coli K-12 solution over the linear dynamic range, which appears to be 2x10^4 – 2x10^7 CFU per ml and has a sensitivity of S = 1.655x10^5 o m2 Kg-1. The limit of detection (LOD) for these sensors was calculated to be approximately 2x10^-9 grams (g), which is estimated to be approximately 2,000 Escherichia coli (E. coli) K-12 cells. However, the sensitivity and insertion loss remained approximately unchanged before and after coating the sensor with 3,3'-Dithiobis(succinimidyl) Propionate (DSP).

Background: This qualitative systematic review protocol aims to explore the experiences of African customers in white-owned restaurants and hotels in post-apartheid South Africa, focusing on the dynamics of service interactions and their implications for racial relations within the hospitality industry. Despite the end of apartheid in 1994, the echoes of historical racial disparities and power imbalances persist, potentially influencing customer experiences in this sector, particularly in establishments owned by individuals of European descent. In view of above, the research question for this study is “How do African customers in white-owned restaurants and hotels in post-apartheid South Africa perceive and experience service interactions, and what are the underlying factors influencing these perceptions, considering historical power imbalances, societal perceptions, lingering effects of apartheid, inclusive practices, and the varied experiences across different hospitality establishments? Study Objectives: Objectives include examining the dynamics of service interactions, identifying factors influencing perceptions and experiences, evaluating alignment with inclusive practices and post-apartheid ideals, and describing African customers' experiences regarding service. Methods: The study will employ the SPIDER Framework to craft a nuanced research question that seeks to understand how African customers perceive and experience service interactions in these settings, considering historical power imbalances, societal perceptions, the lingering effects of apartheid, inclusive practices, and varied experiences across different types of hospitality establishments. This approach aims to dissect the intricate interplay of historical, societal, and economic factors that shape these experiences, providing insights into the complexities of achieving a truly inclusive and equitable hospitality landscape in post-apartheid South Africa. Expected Contribution to knowledge and practice: This review will contribute to a deeper understanding of the challenges and opportunities facing the hospitality industry in fostering environments that reflect the nation's diversity and commitment to reconciliation and social cohesion. By highlighting the lived experiences of African customers and examining the extent to which white-owned establishments embody post-apartheid ideals, this study aims to offer valuable recommendations for industry practitioners and policymakers to promote cultural sensitivity, equity, and inclusivity, thus enhancing the role of the hospitality industry in South Africa's broader societal transformation.

Onchocerciasis, or river blindness, has historically been one of the most important causes of blindness worldwide, and a major cause of socio-economic disruption, particularly in sub-Saharan Africa. Its importance as a cause of morbidity and an impediment to economic development in some of the poorest countries in the world motivated the international community to implement several programs to control or eliminate this scourge. Initially, these involved reducing transmission of the causative agent Onchocerca volvulus through controlling the vector population. When ivermectin was found to be a very effective drug for treating onchocerciasis, the strategy shifted to mass drug administration (MDA) of endemic communities. In some countries, both vector control and ivermectin MDA have been used together. However, traditional vector control methods involve treating rivers in which the black fly vectors breed with insecticides, a process which is expensive, requires trained personnel to administer, and is ecologically harmful. In this review, we discuss recent research into alternatives to riverine insecticide treatment, which are inexpensive, ecologically less harmful and which can be implemented by the affected communities themselves. These can dramatically reduce vector densities and, when combined with ivermectin MDA, can accelerate the time to elimination when compared to MDA alone.

Switzerland, a wealthy country, has a cutting-edge healthcare system, yet per capita, it emits over one ton of CO2, ranking among the world's most polluting healthcare systems. To estimate the carbon footprint of the healthcare system of Geneva’s canton, we collected raw data on the activities of its stakeholders. Our analysis shows that when excluding medicines and medical devices hospitals are the main greenhouse gas emitter by far, accounting for 48% of the healthcare system’s emission, followed by nursing homes (20%), private practice (18%), analysis laboratories (7%), dispensing pharmacies (4%), the homecare institution (3%) and the ambulance services (

This cross-sectional study evaluated the validity of three alternative methods compared to the gold standard 24-h urine collection for estimating dietary sodium intake, a modifiable risk factor for hypertension, among middle-aged and older adults with elevated blood pressure. These included spot urine collection (using Kawasaki, Tanaka, and INTERSALT equations), 24-h dietary recall, and food frequency questionnaire responses, compared against 24-h urine collection in a subset of 65 participants (aged 50–75 years, 58.5 % women, 61.6 % hypertensive) from the DePEC-Nutrition trial. The validity of the methods was assessed using bias, Spearman correlation coefficient (SCC), intraclass correlation coefficient (ICC), and Bland-Altman analysis. Among the alternative methods, spot urine collection using the Kawasaki equation showed the strongest correlation (SCC 0.238; ICC 0.119, 95 % CI -0.079 to 0.323) but it exhibited a significant bias (1414 mg/day, p-value < 0.001) relative to 24-h urine collection. Conversely, dietary surveys had a smaller bias but wider limits of agreement. These findings underscore the complexities of accurately estimating dietary sodium intake using spot urine collection or dietary surveys in this specific population, suggesting that a combination or refinement of existing methodologies might improve accuracy. Further research with larger samples is necessary to develop more reliable methods for assessing sodium intake in this high-risk group.

COVID-19 vaccine hesitancy and its enablers would shape community uptake of non-covid vaccines such as oral cholera vaccine (OCV) in the post-COVID-19 era. This study assessed the impact of COVID-19 vaccine hesitancy and its drivers on OCV hesitancy in a cholera endemic region of the Democratic Republic of Congo. We conducted a community-based survey in Bukavu. The survey included characteristics, intention to take OCV and COVID-19, reasons for COVID-19 hesitancy, and thinking and feeling about COVID-19 vaccines. Poisson regression analyses were performed. Of the 1708 respondents, 84.66% and 77.57% were hesitant to OCV alone and to both OCV and COVID-19, respectively. Hesitancy to COVID-19 vaccines rose OCV hesitancy by 12% (crude Prevalence Ratio, [cPR]=1.12, 95%CI[1.03-1.21]). Independent predictors of OCV hesitancy were living in semi-urban area (adjusted Prevalence Ratio [aPR]=1.10, 95%CI[1.03-1.12]), religious refusal of vaccines (aPR=1.06, 95%CI[1.02-1.12]), concerns about vaccine safety (aPR=1.05, 95%CI[1.01-1.11]) and adverse effects (aPR=1.06, 95%CI[1.01-1.12]), as well as poor knowledge (aPR=1.07, 95%CI[1.01-1.14]). Conversely, the belief about COVID-19 vaccine effectiveness reduced OCV hesitancy (aPR=0.76, 95%CI[0.62-0.93]). COVID-19 vaccine hesitancy and its drivers exhibiting a significant domino effect on OCV uptake. Addressing vaccine hesitancy through community-based health literacy interventions would likely improve the introduction of novel non-COVID-19 vaccines in post-COVID-19 era.

The Bunyavirales order includes at least fourteen families with diverse but related viruses, which are transmitted to vertebrate hosts by arthropod or rodent vectors. These viruses are responsible for an increasing number of outbreaks worldwide and represent a threat to public health. Infection in humans can be asymptomatic, or it may present with a range of conditions from a mild, febrile illness to severe hemorrhagic syndromes and/or neurological complications. There is a need to develop safe and effective vaccines, a process requiring better understanding of the adaptive immune responses involved during infection. This review highlights the most recent findings regarding T cell and antibody responses to the five bunyavirus families with known human pathogens (Peribunyaviridae, Phenuiviridae, Hantaviridae, Nairoviridae, and Arenaviridae). Future studies that define and characterize mechanistic correlates of protection against bunyavirus infections or disease will help inform the development of effective vaccines.

Severe malaria is a major public health concern in Angola, particularly among adults, with limited data on clinical outcomes and manifestations. The study therefore assessed the clinical manifestations and outcome of severe Plasmodium falciparum malaria in adult patients admitted to Hospital Central Dr. António Agostinho Neto of Lubango, Angola. The study retrospectively reviewed the individual records of patients over 14 years old, admitted for severe malaria during the first trimester of 2021 and 2022. World Health Organization (WHO) criteria were used to define severity. A total of 640 patients were recorded into the study, 167 in 2021 and 473 in 2022, distributed across the departments; Intensive Care Unit (ICU; n=81), Medicine (MED; n=458) and Infectiology (INF; n=101). The median age was 26 years and 59.4% were males. The most common manifestation of severe malaria was renal impairment (37.4%). The overall mortality rate was 7% and decreased considerably from 10.2% in 2021 to 5.9% in 2022. The increase in malaria cases during 2022 with increased in prevalence of life-threatening signs like renal impairment, jaundice and impaired conscience, underscores the urgent need for enhanced malaria control and surveillance strategies to mitigate morbidity and mortality, highlighting the potential for antimalarial drug resistance.

The Absorbing/scattering nature of aerosols affects the total radiative forcing and this absorption to total extinction ratio is quantified by single scattering albedo (SSA). Effect of SSA in the Ultraviolet (UV) irradiance is less studied and limited measurements are available. SSA retrieved at Athens, Greece during 2009-2014 from Ultraviolet Multifilter Radiometer (UVMFR) at 332 and 368 nm, were used to calculate incoming UV irradiance, alongside with ones from AERONET at visible wavelengths, from OMI satellite at 342.5 nm and from AEROCOM climatological database at 300 nm. UVA and UVB irradiances were estimated using a Radiative Transfer Model and we found that relative differences could be as high as 20%, while average relative differences varied from 2% to 8.7 % for the whole experimental period. Both UVA and UVB drop by a rate of ~12% for 0.05 aerosol absorption optical depth compared to ones estimated using SSA at visible range. Brewer irradiance measurements at 324nm were used to validate simulated irradiances and a better agreement was found when UVMFR SSAs were used with an average difference of 0.86%, while when using visible or climatological input, relative differences were estimated +4.91 and +4.15% accordingly.

We monitored the water quality and hydrological conditions of a horizontal subsurface constructed wetland (HSSF-CW) in Beijing, China, for 2 years. We simulated the area rate constant and the temperature coefficient with the first-order kinetic model. We examined the relationships between the nitrogen (N) removal rate, N load, seasonal variations in the N removal rate, and environmental factors, such as the area rate constant, temperature, and dissolved oxygen (DO). The effluent ammonia (NH₄⁺-N) and nitrate (NO₃⁻-N) concentrations were significantly lower than the influent concentrations (p<0.01, n=38). The NO₃⁻-N load was significantly correlated with the removal rate (R²=0.9566, p<0.01), but the NH^₄+-N load was not correlated with the removal rate (R²=0.0187, p>0.01). The area rate constants of NO₃⁻-N and NH₄⁺-N at 20 °C were 27.01±26.49 and 16.63±10.58 m∙yr⁻¹, respectively. The temperature coefficients for NO₃⁻-N and NH₄⁺-N were estimated at 1.0042 and 0.9604, respectively. The area rate constants for NO₃⁻-N and NH₄⁺-N were not correlated with temperature (p>0.01). The NO₃⁻-N area rate constant was correlated with the corresponding load (R²=0.9625, p<0.01). The NH₄⁺-N area rate was correlated with DO (R²=0.6922, p<0.01), suggesting that the factors that influenced the N removal rate in this wetland met Liebig's law of the minimum.

Crash prediction of the sharp horizontal curve segment (SHCS) of a freeway is an important tool in analyzing safety of SHCSs and in building a crash prediction model (CPM). The design and crash report data of 88 SHCSs from different institutions were surveyed and three negative binomial (NB) regression models and three generalized negative binomial (GNB) regression models were built to prove that the interactive influence of explanatory variables plays an important role in fitting goodness. The study demonstrates the effective use of the GNB model in analyzing the interactive influence of explanatory variables and in predicting freeway basic segments. Traffic volume, highway horizontal radius, and curve length have been formulated as explanatory variables. Subsequently, we performed statistical analysis to determine the model parameters and conducted sensitivity analysis. Among the six models, the result of model 6, which considered interactive influence, is much better than those of the other models by fitting rules. We also compared the actual results from crashes of 88 SHCSs with those predicted by models 1, 3, and 6. Results demonstrate that model 6 is much more reasonable than models 1 and 3.

In this paper, solar irradiance and wind speed forecasts were performed considering time horizons ranging from 10 min to 60 min, under a 10 min time-step. Global horizontal irradiance (GHI) and wind speed were computed using four forecasting models (Random Forest, k-Nearest Neighbours, Support Vector Regression, and Elastic Net) to compare their performance against two alternative dynamic ensemble methods (windowing and arbitrating). Forecasting models and dynamic forecasting ensembles were implemented in Python for performance evaluation. The performance comparison between the prediction models and the dynamic ensemble methods was carried out by evaluating the RMSE, MAE, R² and MAPE, to evaluate whether the dynamic ensemble forecasting method obtained greater. According to the results obtained windowing dynamic ensemble method was the most efficient among the tested. For the wind speed data, by varying its parameter λ (from 1 to 100), a variable performance profile was obtained, where from λ =1 to λ = 74, windowing proved to be the most efficient, reaching maximum efficiency for λ = 19. Windowing was the best method for the GHI analysis, reaching its best performance for λ = 1. The efficiency gain using windowing was 0.56% when using the wind speed model and 1.96% for GHI.

In this paper, we study the global existence and exponential decay for a dynamic contact problem between a Timoshenko beam with second sound and two rigid obstacles, of which the heat flux is given by Cattaneo's law instead of the usual Fourier's law. The main difficulties arise from the irregular boundary terms, from the low regularity of the weak solution and from the weaker dissipative effects of heat conduction induced by Cattaneo's law. By considering related penalized problems, proving some a priori estimates and passing to the limit, we prove the global existence of the solutions. By considering the approximate framework, constructing some new functionals and applying the perturbed energy method, we obtain the exponential decay result for the approximate solution, and then prove the exponential decay rate to the original problem by utilizing the weak lower semicontinuity arguments.

The energy yield of the Vehicle-integrated photovoltaic (VIPV) differs from that of the standard photovoltaics (PV). It is mainly by the difference of the solar irradiance onto the car-roof and car-bodies as well as its curved-shape. Both meaningful and practical modeling and measurement of the solar irradiance for VIPV are needed to be newly established, not the extension of the current technologies. The solar irradiance was modeled by a random distribution of the shading objects and car-orientation with the correction of the curved surface of the PV modules. The measurement of the solar irradiance onto the car-roof and car-body was done using five pyranometers in five local axes on the car for one year. The measured dynamic solar irradiance onto the car-body and car-roof was used for validation of the solar irradiance model in the car.

With the continual global increase of PV power systems and the inherent weather-induced volatility of their power output, understanding the underlying variability of solar radiation in both space and time is important for the planning and reliable operation of future power grids. This paper concisely reviews recent advances in the characterization of irradiance variability with an emphasis on small spatial and temporal scales (respectively less than about 10\,km and 1\,min), for which comprehensive data sets are time consuming and expensive to collect, and although needed have not been available until recently. Special attention is given to studies dealing with the quantification of variability using such unique data, the analysis and modeling of spatial smoothing, and the evaluation of temporal averaging.

Infections with multi-drug-resistant (MDR) pathogens in food-animals threaten public health and food security. However, the epidemiology and factors associated with MDR Escherichia coli on Ugandan farms are not well known. This study investigated the prevalence, resistance patterns and factors associated with MDR E. coli carriage on chicken farms. A total of 158 E. coli strains were isolated from 158 chicken farms. The disc diffusion method for susceptibility testing was performed. Clinical breakpoints were interpreted according to Clinical and Laboratory Standards Institute guidelines. MDR was defined as resistance to three or more classes of antimicrobials. MDR E. coli prevalence on chicken farms was 62.7% (95% CI: 55.0 – 70.3). High resistance was observed against ampicillin 79.8% (95% CI: 72.7–85.4), tetracycline 72.8% (95% CI: 65.2–79.2), cotrimoxazole 55.7% (95% CI: 47.8–63.3), and ciprofloxacin 38% (95% CI: 30.7–45.9). Farmers who were males (APR = 0.72, CI: 0.55, 0.93), and attained at least secondary education (APR=0.64, CI: 0.46, 0.88) and administration of recommended antibiotic doses (APR = 0.76, CI: 0.59–0.96) posed a lower risk of MDR E. coli carriage. Farms without footbaths posed a heighten risk (APR=1.48, CI: 1.16–1.88). MDR E. coli were highly prevalent on chicken farms. This study underscores the need for antimicrobial stewardship and improved infection prevention strategies on chicken farms.

This study delves into the dynamic field of medical education research, emphasizing the integration of research training within medical curricula. It seeks to understand the impact of such integration on the competencies of future medical professionals. The primary aim is to systematically categorize and analyze the current trends and future directions in medical education research. This involves assessing the influence of research training on medical students' skills and the methodologies used in such research. Methods: The research employs an extensive bibliographic literature review across multiple databases. It classifies studies into categories like experiential or case studies, editorials, and original research articles. This classification is based on criteria such as geographical location, research objectives, theoretical frameworks, and methodologies. Results: Findings reveal a diverse landscape in medical education research, with a significant emphasis on research training. The research showcases varying methodologies and approaches used globally, highlighting the thematic focus and geographical distribution of these studies. Conclusion: Medical education research is a globally expansive and evolving field. It underscores the importance of continuous investigation, particularly focusing on integrating research elements at curricular levels and exploring innovative educational strategies. The study also points out potential gaps in research, especially in underrepresented regions, indicating directions for future research efforts.

Africa was the only continent not to achieve the 2015 Millennium Development Goal of 50% poverty reduction. This paper asks whether Africa will fare better in meeting Sustainable Development Goals (SDGs) addressing poverty and hunger by 2030. To answer this question we examine literature, including our field research published over the last thirteen years. We find that ‘sustainable development’ is a failed concept immersed in the contemporary global economic system that favors growth over ecosystem stability and patriarchal systems of governance that undervalue women’s capacity for sustainability in their care-work as food providers. We examine barriers to women’s farming (climate change, gender bias, limited access to land, technology, finance) and provide examples of women’s innovative strategies for overcoming these barriers in their care practices toward family and community well-being and ecosystem health. We conclude that sustainability is only possible through transformation of thinking away from approaches that value profit over people and ecosystems and toward gender-based approaches for achieving the goals laid out in the SDGs through holistic, integrative systems of ecosystem fit.

The conventional well placement was done manually by using a numerical reservoir simulator, and it required a lengthy trial-and-error process. It required great experience and expertise to manipulate the variables and uncertainties that lie on the reservoir to determine the best placement of the well. In addition, the traditional gradient-based methods such as Line-search and Trust-region were not viable in terms of maximum results obtained. Gradient-based methods were too dependent on the surface gradient of the solution and may only converge to local optima instead of global optima. Complex reservoirs have rough surfaces with high uncertainties, which hinders the traditional gradient-based method from converging to global optima. Thus, genetic algorithms were utilized to automate the manual trial-and-error process and to overcome the limitations of the traditional gradient-based method. The objectives of this study were to analyse the effect of different initial well placement distributions, the number of random solution sizes, and the crossover rate on cumulative oil production. A synthetic reservoir model built using CMG Builder was used as the testing platform for the optimization problems. Well-placement parameterization and optimization set-up were carried out using the CMG CMOST optimization tool. The integration of CMG IMEX and CMOST optimized cumulative oil production based on the objectives of the study. The results obtained showed that the higher number of random solutions used resulted in higher cumulative oil production, with more generations needed to reach the optimum solution. It can be concluded that the larger number of random solutions used increased the probability of reaching the optimum solution, but will take more generations.

Sleep disorders have become a public health problem for many reasons. The aim of this systematic review is to describe social, economic, and environmental determinants of sleep disturbances in Australia and New Zealand. A total of 22 studies, 14 from Australia and 8 from New Zealand involving children, adolescents and adults are included in the review. In summary, we found that sleep health disparities among children and adolescents in both countries are strongly associated to parental SES. Overall, lower family SES such as low parental income, low parental education, low SES area index are associated with higher sleep disturbances among children and adolescents. In adults, results revealed that SES determinants such as low income, lower education, unemployment, and night work were associated with sleep disturbances. Specifically, unemployment was associated with poor sleep quality, insomnia, and increased likelihood of suboptimal sleep efficiency. Low income and lower education were associated with high risk of OSA, longer sleep duration, insomnia, higher odds of suboptimal sleep duration and sleep onset latency.

In this study we focus on measurements and modeled UV index at the region of Athens, Greece, during a period of a low ozone event. During the period of 12 to 19 of May 2020, total column ozone (TOC) showed extremely low values 35-55 DU (up to 15%) decrease from the climatic mean (being lower than the -2σ). This condition favors the increase of UV erythemal irradiance, since stratospheric ozone is the most important attenuator at the UVB spectral region. A parallel intrusion of Saharan Dust aerosols in the region has masked a large part of the low ozone effect on UV irradiance. In order to investigate the event, we have used spectral solar irradiance measurements from the Precision Solar Radiometer (PSR), total column ozone from the BREWER spectrophotometer and Radiative Transfer Model (RTM) calculations. Model calculations of UV Index (UVI) showed an increase of ~30% compared to the long term normal UVI due to the low TOC while at the same time and for particular days, aerosols masked this effect by ~20%. The study points out the importance of accurate measurements or forecasts of both ozone and aerosols when deriving UVI under unusual low ozone-high aerosol conditions.

The gut-brain axis (GBA) represents a complex, bidirectional communication network that intri-cately connects the gastrointestinal tract with the central nervous system (CNS). Understanding and intervening in this axis opens a pathway for therapeutic advancements. In light of this, the current review assesses the effectiveness of neuromodulation techniques in treating neurological and gastrointestinal disorders by modulating the GBA, involving key elements such as gut micro-biota, neurotrophic factors, and proinflammatory cytokines. Through a comprehensive literature review encompassing PubMed, Google Scholar, Web of Science, and the Cochrane Library, and analyzing 182 relevant articles, this research highlights how neuromodulation can positively impact the management of functional gastrointestinal disorders (FGIDs), chronic pain, inflammation, and a range of GI disorders like Crohn's disease and ulcerative colitis. Despite existing challenges, the ability of neuromodulation to adjust disrupted neural pathways, alleviate pain, and mitigate in-flammation is significant in improving the quality of life for patients, thereby offering exciting prospects for future advancements in patient care.

Among other fossil fuels, natural gas is a major energy source. It is generally created saturated with water vapor. Dehydration of natural gas is vital in the gas business to remove water vapor from the gas supply, which may cause hydrate development in pipes. Gas dehydration employs Tri ethylene glycol (TEG) to remove water vapor from natural gas flow. The wet gas is dehydrated with lean glycol in an absorber, and the rich glycol is recovered and reused. This work investigates the use of dry natural gas instead of nitrogen in the glycol dehydration re-generator, and compares the results using HYSYS modeling and simulation. The two techniques were compared for capital and utility expenses, while maintaining the identical glycol purity criteria. The wet gas from the stripping mechanisms may also be utilized to run steam pumps and compressors or recycled. The model is based on the real mechanism flow diagram. Finally, the findings of this model might be used to design a new heat and material balance for the plant.

Matrices and their inverses allow accurate calculations to be produced quickly and compactly and can be used to control any process represented by a system of equations. Singular matrices require extensive workarounds (costing time and money) to solve these systems of equations because they have no inverse. Finding their inverse involves division by zero. Nevertheless, recently a new number set called semi-structured complex numbers was developed to enable division by zero in algebraic equations. The aim of this research was to demonstrate that the inverse of a singular matrix can be found using semi-structured complex numbers. This research reveals (1) Singular matrices and their inverses can be used to find a unique solution to a pair of simultaneous equations that appear to have infinitely many solutions or appear to have no solution; (2) Singular matrices map coordinates in projective space to coordinates in Euclidean space and their inverse maps coordinates in Euclidean space to coordinates in projective space; (3) the inverse of a singular matrix proves that parallel lines in Euclidean space do not intersect but in projective space intersect at a “point at infinity” and (4) collinear lines that intersect at infinitely many points in Euclidean space only intersect at one point in projective space.

Water footprint has been widely used to illustrate the consumption of water in many situations; for instance, in products, processes or regions of interest. In this work, we analyzed – using a sensitivity analysis approach – the effect of some variables in the calculation of the water footprint in the viticulture in Brazilian Serra Gaúcha (the major producing region of Brazilian Wine).The classical Penman-Monteith model for evapotransporation was considered, with uncertainties in some parameters (dead mulch covering fraction in the vineyard, maximum temperatures for some months, altitudes and latitudes of the site). The sensitivity analysis was conducted using the SAFE toolbox under Octave framework. The results indicated that the the portion of the water footprint corresponding to the evapotranspiration is more sensitive to the values of mulch covering fraction and the altitude of the site in comparison with the latitude and the maximum temperatures.

In this paper, we study the semilinear pseudo-parabolic equations $\displaystyle u_{t} - \triangle_{\mathbb{B}}u - \triangle_{\mathbb{B}}u_{t} = \left|u\right|^{p-1}u$ on a manifold with conical singularity, where $\triangle _{\mathbb{B}}$ is Fuchsian type Laplace operator investigated with totally characteristic degeneracy on the boundary $x_{1} = 0$. Firstly, we discuss the invariant sets and the vacuum isolating behavior of solutions with the help of a family of potential wells. Then, we derive a threshold result of existence and nonexistence of global weak solution: for the low initial energy $J(u_{0})<d$, the solution is global in time with $I(u_{0}) >0$ or $\displaystyle\Vert \nabla_{\mathbb{B}}u_{0}\Vert_{L_{2}^{\frac{n}{2}}(\mathbb{B})} = 0$ and blows up in finite time with $I(u_{0}) < 0$; for the critical initial energy $J(u_{0}) = d$, the solution is global in time with $I(u_{0}) \geq0$ and blows up in finite time with $I(u_{0}) < 0$. The decay estimate of the energy functional for the global solution and the estimates of the lifespan of local solution are also given.

In this paper, we consider a fourth-order suspension bridge equation with nonlinear damping term |u_t|^m-2u_t and source term |u|^p-2u. We give necessary and sufficient condition for global existence and energy decay results without considering the relation between m and p. Moreover, when p>m, we give sufficient condition for finite time blow-up of solutions. The lower bound of the blow-up time T_max is also established. It worth to mention that our obtained results extend the recent results of Wang (J. Math. Anal. Appl., 2014) to the nonlinear damping case.

The research develops and validates new decomposition models for DNI estimations from Southern African data. The results demonstrated improved DNI estimation accuracy compared to the baseline models across all testing and validation datasets. These outcomes suggest that utilising a localised model can significantly enhance DNI estimations for Southern Africa and potentially for developing similar models in diverse geographic regions worldwide. Furthermore, clustered models highlighted the potential advantages of grouping data based on shared geographical and climatic attributes. This clustering approach could enhance decomposition model performance, particularly when local data is limited or data is available from multiple nearby stations. The Southern African decomposition model, which encompasses a wide spectrum of climatic regions and geographic locations, exhibited notable improvements over the baseline models despite occasional overestimation or underestimation. The overall metrics affirm the substantial advancement achieved with the Southern African model. This study focused on validating the model for hourly DNI in Southern Africa within a range of clearness index-intervals from 0.175 to 0.875. Implementing accurate decomposition models in developing countries can accelerate the adoption of renewable energy sources, diminishing reliance on coal and fossil fuels.

The study conducts a comparative analysis of solar radiation estimation methods, assessing the efficacy of the Heliosat-2 algorithm against ground measurements across seven distinct countries: Netherlands, Spain, Japan, Namibia, South Africa, Saudi Arabia, and India. To achieve this, it utilizes two distinct satellite data sources—Himawari-8 for Japan and Metosat Second Generation-MSG for the rest of the countries—spanning the years Jan 2022 to April 2024. A robust methodology for determining albedo parameters specific to Heliosat-2 was developed. During cloudy days, the estimates provided by Heliosat-2 generally exceeded the ground measurements in all the countries. Conversely, on clear days, there was a tendency for underestimation, as indicated by the median value of the mean bias (MB) across most of the countries. The Heliosat-2 model slightly underestimates daily radiation values, with a median MB ranging from −27.5 to +10.2 W.m⁻². Notably, the median root mean squared error (RMSE) on clear days is significantly lower, with values ranging from 24.8 to 108.7 W.m⁻², compared to cloudy days where RMSE values lie between 75.3 and 180.2 W.m⁻². In terms of R² values, both satellites show a strong correlation between the estimated and actual values, with a median value consistently above 0.86 on a monthly scale and over 92% of daily data points falling within ±2 standard deviation.

Annually, more than 1.5 million preventable new hepatitis B (HBV) infections continue to occur, with an estimated global burden of 296 million individuals living with chronic hepatitis B infection. This substantial health challenge results in over 820,000 annual deaths attributed to complications such as liver cirrhosis and hepatocellular carcinoma (HCC). HBV vaccination remains the cornerstone of public health policy to prevent chronic hepatitis B and its related complications. It serves as a crucial element in the global effort to eliminate HBV, as established by the World Health Organization (WHO), with an ambitious 90% vaccination target by 2030. However, reports on global birth dose coverage reveal substantial variability, with an overall coverage rate of only 46%. This comprehensive review thoroughly examines global trends in HBV vaccination coverage, investigating the profound impact of vaccination on HBV prevalence and its consequences across diverse populations, including both high-risk and general demographics. Additionally, the review addresses the formidable challenges and facilitating factors essential for achieving WHO's HBV vaccination coverage objectives and elimination strategies in the coming decade and beyond.

ABSTRACT Lubricants play a crucial role in reducing friction and wear between surfaces in relative motion. Engine oil, as a lubricant, is specifically designed to minimize friction and wear between the moving parts of different equipment and machinery. Engine oil blending serves the purpose of adjusting the variety of lubricants available to meet specific performance requirements. Through blending, it is possible to tailor the characteristics of the lubricating oil, such as viscosity, stability, and additive content, to optimize its effectiveness in reducing friction, protecting engine components, and enhancing overall equipment performance. By customizing lubricant formulations through blending, manufacturers can address the diverse lubrication needs of modern engines and machinery, ensuring smooth operation, longevity, and efficiency.To enhance the quality of the lubricant and achieve the desired high-performance multi-grade engine oil, a systematic approach was followed. The process began with testing the specific gravity of the oil using a hydrometer and thermometer to ensure accurate measurements. Subsequently, 5 liters of base oil were carefully measured and poured into a stainless steel reactor pot to serve as the blending vessel. Following this, 1 liter of paraffin oil (100N) was added to the base oil to introduce specific properties to the blend. To further optimize the formulation, 0.42 kg (7% of the total blend) of additives, including a selection of specific performance-enhancing compounds, was incorporated. These additives, such as Aspen, Tackifier, and other essential components like anti-wear, corrosion inhibitors, detergents, dispersants, and antioxidants, were meticulously measured and added to the mix. Through this precise blending process, the goal was to craft a high-quality multi-grade engine oil that meets the stringent performance requirements for various operating conditions and equipment types. After the melted Aspen and dissolved tackifier were added to the mixture, thorough stirring was carried out to ensure uniform distribution until a homogeneous blend was achieved. The mixture was then exposed to heat to facilitate the reaction between the base oil and additives, reaching a temperature of 70°C for optimal blending. Subsequently, 0.5 kg of viscosity index improver was introduced into the mixture and stirred continuously for a period of 5 minutes to ensure proper integration. Following this step, 5 grams of dye were carefully added to the mixture, and stirring was continued to evenly disperse the coloring agent throughout the blend. This meticulous process aimed to ensure that all components were effectively incorporated, facilitating the production of a high-quality, customized multi-grade engine oil with enhanced performance characteristics and optimal lubricating properties. After subjecting the mixture to a temperature of 70°C, the heat source was removed, allowing the product to gradually cool down to room temperature, which was estimated to be around 30°C. Following this cooling process, the product underwent a filtration step to remove any residual impurities present in the mixture. A sample of the purified product was then extracted for further analysis. Quality control tests were meticulously carried out on the sample to ensure that the product met the rigorous standards set by the Standard Organization of Nigeria (SON). The results obtained from the quality control tests were highly promising, indicating that the product indeed complied with the stringent specifications outlined by the regulatory body. This adherence to quality standards is essential in ensuring the product's reliability and performance in various applications. The successful outcome of the quality control test underscores the meticulous attention to detail and commitment to excellence in the production process. The rigorous quality control procedures implemented in the analysis of the product highlight the commitment to upholding high standards of quality and safety in the manufacturing process. By consistently meeting and exceeding industry regulations and standards, the product not only demonstrates its reliability but also reflects a dedication to customer satisfaction and product excellence. The adherence to the SON standards showcases a commitment to producing top-quality products that meet the needs and expectations of consumers and industry stakeholders alike.

Recent state-of-the-art scene text recognition methods have primarily focused on horizontal text in images. However, in several Asian countries, including China, large amounts of text in signs, books, and TV commercials are vertically directed. Because the horizontal and vertical texts exhibit different characteristics, developing an algorithm that can simultaneously recognize both types of text in real environments is necessary. To address this problem, we adopted the direction encoding mask (DEM) and selective attention network (SAN) methods based on supervised learning. DEM contains directional information to compensate in cases that lack text direction; therefore, our network is trained using this information to handle the vertical text. The SAN method is designed to work individually for both types of text. To train the network to recognize both types of text and to evaluate the effectiveness of the designed model, we prepared a new synthetic vertical text dataset and collected an actual vertical text dataset (VTD142) from the Web. Using these datasets, we proved that our proposed model can accurately recognize both vertical and horizontal text and can achieve state-of-the-art results in experiments using benchmark datasets, including the street view test (SVT), IIIT-5k, and ICDAR. Although our model is relatively simple as compared to its predecessors, it maintains the accuracy and is trained in an end-to-end manner.

We investigated the liquid water path and global solar irradiance at ground (Q) according to the ICON model, CLOUDNET measurements in Lindenberg, Munich, Jülich, and BSRN observations in Lindenberg. The liquid water path is underestimated, while global irradiance is overestimated. The lower liquid water path is due to liquid water content underestimation practically in all atmosphere layers and lower frequency of liquid clouds occurrence compare to observations. The latter is partly associated with a reduced model’ sensitivity to the cloud condensation nuclei (CCN). An increase in CCN from 250 cm-3 (typical background value for the region of interest) to 1700 cm-3 (characteristic of polluted continental clouds) leads to an increase in grid-scale liquid water path by 40% and a decrease in Q under overcast conditions by 12%. However, we also showed that liquid water path is not a key factor of Q overestimation. The main factor is an inaccurate description of the cloud spatial structure, where the correct prediction of the direct to global irradiance ratio as a spatial characteristic of clouds plays the most important role compared to standard cloud fraction.

Sarcopenia is associated with clinical complications, which increase mortality. Effective sarcopenia risk screening in the elderly should be grounded in a comprehensive assessment, encompassing both nutritional status and medication use. Current screening tools, while emphasizing muscular per-formance, exhibit limited sensitivity in identifying elderly individuals at risk of sarcopenia. This cross-sectional study aimed to develop a sarcopenia risk screening tool, named Sarc-Global, with enhanced sensitivity, incorporating factors pertinent to the overall health of the elderly. Utilizing the criteria established by EWGSOP2 for diagnosing sarcopenia, we evaluated 395 communi-ty-dwelling elderly individuals. This evaluation served as a reference for assessing the efficacy of two validated questionnaires, Sarc-F and Sarc-CalF, and our newly developed Sarc-Global. Con-structed through multiple logistic regression, Sarc-Global integrates variables such as sex, age, medication use, body mass index, arm circumference, and handgrip strength – all significantly associated with sarcopenia (p

Revolutionizing Lng Plant Construction and its Comprehensive Comparative Analysis And Evaluation Of Modular Design Development Versus Stick-Built Approach For Enhanced Efficiency And Cost-Effectiveness,.Although the utilization of modularization concepts in the LNG industry remains limited, this study focuses on exploring their potential. It is worth noting that modular units typically incur higher costs compared to field erected units due to the additional requirements of structural steel and robustness for transportation purposes.Nevertheless, the increased cost of modularization can often be balanced by conducting the work at the fabrication site instead of on-field construction. This approach reduces the overall project cost by minimizing field construction expenses and shortening the construction schedule. The objective of this paper is to assess and compare LNG modularization options for a newly established LNG facility in comparison to a conventional stick-built plant used as the base case.:The paper delves into various topics related to LNG plant construction, such as the development of modular units, a comprehensive comparison of different options, evaluation of construction schedules and manpower requirements, logistics considerations, and a recommended approach for design and construction. The cost estimates and engineering, procurement, and construction (EPC) schedules are meticulously compared for each option. Additionally, an inshore/near shore gravity base structure (GBS) option is included for further comparison. It is crucial to emphasize that establishing general costs is not possible as each project is distinct and requires individual study and analysis.:Each project has unique characteristics, resulting in varying shapes of cost curves and break-even points. The outcomes of the feasibility evaluation play a crucial role in determining the extent to which the modular approach to construction is advantageous for the specific project at hand. The evaluation takes into consideration multiple factors to determine the potential benefits of adopting a modular construction approach, allowing decision-makers to make informed choices regarding the project's construction methodology

Accurate short-term solar irradiance forecasting is crucial for the efficient operation of solar energy driven photovoltaic (PV) power plants. In this research, we introduce a novel hybrid ensemble forecasting model that amalgamates the strengths of machine learning tree-based models and deep learning neuron-based models. The hybrid ensemble model integrates the interpretability of tree-based models with the capacity of neuron-based models to capture complex temporal dependencies within solar irradiance data. Furthermore, stacking and voting ensemble strategies are employed to harness the collective strengths of these models, significantly enhancing prediction accuracy. This integrated methodology is enhanced by incorporating pixels from satellite images provided by the European Organization for the Exploitation of Meteorological Satellites (EUMETSAT). These pixels are converted into structured data arrays and employed as exogenous inputs in the algorithm. The primary objective of this study is to improve the accuracy of short-term solar irradiance predictions, spanning a forecast horizon up to 6 hours ahead. The incorporation of EUMETSAT satellite image pixels data enables the model to extract valuable spatial and temporal information, thus enhancing the overall forecasting precision. This research also includes detailed analysis of the derivation of GHI using satellite images. The study was carried out and the models tested across three distinct locations in Austria. A detailed comparative analysis was carried out for traditional Satellite (SAT) and Numerical Weather Prediction (NWP) models with hybrid models. Our findings demonstrate a higher skill score for all of the approaches compared to smart persistent model and consistently highlight the superiority of the hybrid ensemble model for short-term prediction window of 1 to 6 hours. This research underscores the potential for enhanced accuracy of the hybrid approach to advance short-term solar irradiance forecasting, emphasizing its effectiveness at understanding the intricate interplay of the meteorological variables affecting solar energy generation worldwide. The results of this investigation carry noteworthy implications for advancing solar energy systems, thereby supporting the sustainable integration of renewable energy sources into the electrical grid.

The teaching and learning environment have changed significantly over the last decade with the integration of an increasing amount of information and communication technologies, especially in distance education due to global pandemics, total lockdowns, isolation, and quarantine periods. The number of numerous virtual and non-virtual tools involved in educational processes is growing day by day. In terms of technological innovations used in learning environments, many researchers and educators are trying their best to bring more creative ideas into the technology- based learning environments. Although higher educational institutions have greatly benefited from the growing number of hardware and software resources in the educational process, they have also faced some setbacks that have harmed the learning processes. These technologies have in turn complicated some of the processes in the learning atmosphere. Therefore, we take Spanish teaching course as an example to present the challenging smarter teaching and learning systems that higher educational institutions face today.

Review of the existing bibliography shows that the direction and magnitude of the long-term trends of UV irradiance, and their main drivers, vary significantly throughout Europe. Analysis of total ozone and spectral UV data recorded at four European stations during 1996 – 2017 reveals that long-term changes in UV are mainly driven by changes in aerosols, cloudiness, and surface albedo, while changes in total ozone play a less significant role. The variability of UV irradiance is large throughout Italy due to the complex topography and large latitudinal extension of the country. Analysis of the spectral UV records of the urban site of Rome, and the alpine site of Aosta reveals that differences between the two sites follow the annual cycle of the differences in cloudiness and surface albedo. Comparisons between the noon UV index measured at the ground at the same stations and the corresponding estimates from the DWD forecast model and OMI/Aura observations reveal differences of up to 6 units between individual measurements, which are likely due to the different spatial resolution of the different datasets, and average differences of 0.5 – 1 unit, possibly related to the use of climatological surface albedo and aerosol optical properties in the retrieval algorithms.

Keywords: Artificial Neural Network (ANN), Support Vector Machine (SVM), Support Vector Regression (SVR), Lightweight Gradient Boosting Machines (Light GBM), Machine Learning, Solar Irradiance (SI), Solar forecasting

In the dynamic interplay between people and their physical environments, the Global South stands as a mosaic undergoing a multitude of transformative influences in architecture and urbanism where examining social sustainability becomes imperative. While prevailing attention remains on environmental and economic sustainability, this study addresses a persistent gap in the urban literature by focusing on the dynamic and manifold nature of social sustainability. Positioning itself within the context of sustainable development, the study links the pursuit of social aspects of sustainability with selected unique urban contexts from the Global South. Five cases that include Alexandria (Egypt), Tripoli (Libya), Basra (Iraq), Lilongwe (Malawi), and Accra (Ghana) are discussed through multi-layered investigations that involve attitude surveys, interviews, focus groups, participatory systematic observations, and behavioral mapping, engaging directly with inhabitants and stakeholders. Uncovering people-place narratives in the identified contexts, the cases are developed into five knowledge typologies that serve as practical tools for planning and design decision-making, policy formulation, and academic discourse. Discussions are conceived to demonstrate the transformative role people-place narratives play in fostering a more sustainable and equitable urban future. Conclusions are drawn to offer practical insights for stakeholders involved in various capacities in shaping the urban landscape of the Global South.

Plastics play a pivotal role in the principles of a circular economy, where their effective recycling post-utilization, leading to economic value generation and minimal environmental harm, is crucial for achieving sustainable management. Extensive research has delved into the incorporation of waste plastics in concrete, showcasing promising outcomes with a myriad of advantages..The escalating volume of plastic waste is becoming a pressing issue, contributing to environmental pollution, particularly in densely populated cities and towns in Nigeria such as Delta, Aba, Port Harcourt, Onitsha, Enugu, Benue, and Ogun. These urban centers experience high consumption of goods packaged or sealed in plastic materials. Tourist destinations are also affected as large quantities of plastic waste are improperly disposed of or incinerated, resulting in environmental contamination and air pollution. Efforts to address this growing concern are crucial to safeguarding the environment and public health in these regions.Therefore, it is imperative to find effective ways to utilize these waste plastics. By cleaning low-density polyethylene bags and combining them with sand at specific proportions, high-strength bricks can be produced. These bricks not only exhibit thermal and sound insulation properties but also help in pollution control and cost reduction in construction projects. This innovative approach not only addresses the issue of accumulating plastic waste, a non-biodegradable pollutant, but also offers a sustainable solution to manage plastic waste while contributing to the construction industry's efficiency and environmental protection., By incorporating waste plastic and nylon into brick production, we not only reduce the amount of sand extracted from our natural resources like rivers and seas but also utilize the surplus plastic waste that is currently discarded. This research focuses on creating eco-friendly bricks by incorporating molten plastic, nylon, and plastic bottles in varying percentages (0 to 15% by weight) along with 5kg of fly ash. The experimental results from this study will shed light on the feasibility and benefits of using these materials in brick manufacturing, highlighting the potential of sustainable construction practices that minimize environmental impact and resource depletion, The experimental process involved utilizing cement and sand to complete the brick composition, with curing conducted underwater for 29 days followed by baking at temperatures between 100°C to 120°C for 2 hours. The resulting eco-friendly bricks exhibited key characteristics such as being lightweight, porous, having low thermal conductivity, and displaying appreciable mechanical strength. Interestingly, the compressive strengths of these bricks, post the addition of waste plastic and nylon, were found to be comparable to that of conventional bricks. Additionally, these eco-friendly bricks showcased reduced water absorption capacity compared to regular bricks, offering a promising alternative for sustainable and efficient construction practices.The eco-friendly bricks made from A, B, C, and D using 0%, 5%, 10%, and 15% plastic/nylon waste showed comprehensive strengths of 19.5 ,19.46, 20.3, and 21.1 respectively, with corresponding water absorption percentages of 0.34, 0.25, 0.22, 0.20, and 0.085. The efflorescence values were lower than those of normal bricks. These bricks are likely to enhance energy efficiency in buildings and provide economic value to manufacturers, thereby promoting a sustainable ecosystem for plastic waste management with the involvement of all stakeholders.

Objectives: To assess the short-term impact of a single global stretching session on plantar pressures and lumbar range of motion (RoM) over one week in sedentary university students. Design: A randomised controlled trial with two parallel groups. Participants: Sixty-four university students were randomly assigned to a stretching group or control group. The stretching group received a single session of global stretching and the control group remained seated for the same length of time as the stretching session. Main outcome measures: Lumbar RoM and plantar pressures were assessed before, immediately after, 48 hours after, and 7 days after intervention. Results: Group-by-time interaction was significant for lumbar lateral flexion (p = 0.044), right maximal pressure (p = 0.003), left maximal pressure (p = 0.008), right mean pressure (p = 0.025), left mean pressure (p = 0.002), and maximal pressure minus mean pressure in right foot (p = 0.007). The model with plantar pressures showed a significant difference for group-by-time interaction (p = 0.010).Conclusion: Global stretching seems to counteract the ill-effects of prolonged sitting up to seven days with respect to plantar pressure in standing without improving lumbar ROM

Energy dissipation is one of the most important factors in choosing stepped spillways. However, few studies are about energy dissipation with different horizontal face angles. In this paper, the realizable k-ε turbulence model was used to study the flow field and energy dissipation rates of different stepped spillways with five horizontal face angles in the skimming flow regions. It shows that the free water surfaces and energy dissipation rates change with horizontal face angles and the energy dissipation rates initially decrease and then increase as the horizontal face angle increases. And the horizontal face angles cause the great changes of flow field.

As the structure of horizontal gas wells is more complicated than that of vertical wells, the form of the liquid-carrying in different sections does not well agree. This makes it problematic to apply the widely used liquid-carrying theory of vertical gas wells in horizontal gas wells. Since the theory focused on the critical gas flow rate, it cannot quantify how much liquid it can remove. Simultaneously, it ignores the fact that the liquid-carrying ability of gas flow is limited and the producing liquid has a certain amount of flowing energy. In this study, the gas-liquid flow law of horizontal gas wells and wellhead drainage stability in different tubing depths were firstly studied. Then, the stability of gas drainage for different tubing depths was analyzed and confirmed. Given the disadvantages of the typical theory of critical gas flow, the mathematical model of different tubing depths for gas drainage is established for horizontal gas wells. The innovative model could take the energy of gas flow and liquid flow into account, and quantify the liquid volume which was removed. By verifying the model with the experiments, the result showed that the relative error of the model is generally less than 10%. It shows the research could provide a scientific basis for the analysis and liquid-carrying capacity for horizontal gas wells.

Gravel packing completion method for horizontal wells has the advantages of maintaining high oil production for a long time, maintaining wellbore stability and preventing sand production, so it has become the preferred completion method for horizontal wells. At present, this technology still faces the problems of high sand bed height and poor gravel migration. In order to improve the efficiency of gravel packing in horizontal wells, pulsed gravel packing technology for horizontal wells is proposed for the first time. Based on the mechanism of hydraulic pulse, the Eularian model, RNG K-ε model and CFD model are used to simulate the solid-liquid two-phase flow. By optimizing the parameters such as frequency and amplitude of pulse waveform, the optimal pulse waveform of pulsed gravel packing in horizontal wells is determined. The effects of parameters such as sand-carrying fluid displacement, sand-carrying fluid viscosity, sand-carrying ratio, gravel particle size and string eccentricity on pulsed gravel packing in horizontal wells are studied, and the distribution law of gravel migration velocity and volume fraction in horizontal wells is obtained. According to the results, it can be seen that with the increase of displacement and viscosity of carrier fluid, the volume fraction of fixed bed and moving bed decreases gradually, while that of suspension bed increases gradually. With the increase of sand-carrying ratio, gravel particle size and string eccentricity, the volume fraction of fixed bed and moving bed increases gradually, while that of suspended bed decreases gradually. Comparing the effects of conventional gravel packing and pulsed gravel packing in horizontal wells, it can be concluded that the efficiency of pulsed gravel packing in horizontal wells is higher. The volume fraction of fixed bed and moving bed decreased by 30% and 40% respectively, while the volume fraction of suspended bed increased by 20%. The migration velocity of moving bed and suspended bed increased by 40% and 25% respectively. And the migration ability of gravel improved obviously.

Spent nuclear fuel and high-level radioactive waste can be disposed in deep horizontal drillholes in sedimentary, metamorphic, or igneous rocks. Horizontal drillhole disposal has safety, operational, and economic benefits: The repository is deep in the brine-saturated zone far below aquifers in a reducing environment of formations that can be shown to have been isolated from the surface for millions of years; its depth provides safety against inadvertent intrusion, earth¬quakes, and near-surface perturbations; it can be placed close to the reactors and interim storage facilities, minimizing transportation; disposal costs per ton of waste can be kept substantially lower than for mined repositories by its smaller size, reduced infrastructure needs, and staged imple¬mentation; and, if desired, the waste could be retrieved using “fishing” technology. In the proposed disposal concept, corrosion-resistant canisters containing unmodified fuel assemblies from commercial reactors would be placed end-to-end in up to 50 cm diameter horizontal drill¬holes, a configuration that reduces mechanical stresses and keeps the temperatures below the boiling point of the brine. Other high-level wastes, such as capsules containing 137Cs and 90Sr, can be disposed in small-diameter drillholes. We provide an overview of this novel disposal concept and its technology, discuss some of its safety aspects, and compare it to mined repositories and the deep vertical borehole disposal concept.

As the demand for fossil fuels continues to rise and their availability becomes increasingly limited, it is crucial to explore innovative approaches to optimize fuel combustion in existing systems. Among various engines, diesel engines are heavily reliant on fluid motion within the engine cylinder, which plays a critical role in fuel-air mixing. This abstract focuses on the potential of dynamic mathematical model simulation for multi-compartment rotor compressed combustion engines, aiming to revolutionize power generation by enhancing fuel burning efficiency. By leveraging advanced simulation techniques, this research seeks to unlock new insights into fluid dynamics and optimize fuel-air mixing, leading to more efficient and sustainable energy utilization. Through this exploration, we aim to pave the way for groundbreaking advancements in the field of combustion engines, ultimately contributing to a greener and more sustainable future. In the realm of internal combustion engines, the fluid dynamics within the engine cylinder greatly influence the combustion processes and heat transfer. For compression ignition (C.I) engines, both the bulk gas motion and turbulence characteristics play vital roles in engine performance. This study focuses on enhancing the combustibility of the fuel-air mixture in C.I engines by modifying the engine design to induce turbulence through squish and tumble flows. The modification involves creating multiple compartments on the rotor crown, comprising three small chambers spaced 120º apart. By implementing this design, the aim is to optimize the fuel-air mixing and improve the overall combustion efficiency. Through comprehensive analysis and experimentation, we seek to revolutionize C.I engine technology and pave the way for more efficient and environmentally-friendly power generation. In this study, the performance of a compression ignition (C.I) engine with a multiple compartment rotor has been analyzed under motoring conditions using computational fluid dynamics (CFD) simulations with FLUENT software. The obtained results have been compared with those of a base C.I engine. The analysis focused on the effects of the modified engine design on the tumble ratio and squish velocity, which are important parameters for fuel-air mixing and combustion efficiency. The results indicated a significant improvement with the modified engine, with a 35% increase in tumble ratio and a 31% increase in squish velocity compared to the base engine. These findings suggest that the modified engine design has the potential to enhance fuel-air mixing and combustion performance, leading to improved overall engine efficiency. This research presents promising insights into the optimization of C.I engine design and contributes to the development of more efficient and environmentally-friendly power generation technologies..

Background: Penile squamous cell carcinoma (PSCC) is classified into two prognostically distinct types: human papillomavirus (HPV)-associated and HPV-independent. Conversely, the impact of p53 status on prognosis remains controversial. We correlated HPV and p53 status with prognosis in a large series of PSCC patients. p53 was analysed according to a recently described immunohistochemical (IHC) pattern-based framework that includes two normal (scattered, mid-epithelial) and four abnormal patterns (diffuse, basal overexpression, cytoplasmic and null) and closely correlates with TP53 mutational status. Methods: A total of 122 patients with surgically treated PSCC in three hospitals in Barcelona, Spain, were included. Based on HPV in situ hybridization and p16 and p53 IHC expression, the tumors were classified into three molecular types: HPV-associated, HPV-independent/p53 normal, and HPV-independent/p53 abnormal. All patients were followed for at least 22 months (median 56.9 months), and disease-specific survival (DSS) was analysed. Results: Thirty-six tumors (29%) were HPV-associated, 35 (29%) were HPV-independent/p53 normal, and 51 (42%) were HPV-independent/p53 abnormal. Disease-related deaths were observed in 3/36 (8%), 0/35 (0%) and 14/51 (27%) of the patients, respectively (p&lt;0.001). A total of 7/14 deaths in the latter group were patients with tumors showing p53 patterns not recognized in the classical p53 IHC interpretation (basal, null, cytoplasmic). According to our multivariate analysis, HPV-independent/p53 abnormal tumors and advanced stage were associated with impaired DSS (hazard ratio=23.4, 95% confidence interval [CI]= 2.7-3095.3; p=0.001 and 16.3, 95% CI=1.8-2151.5; p=0.008, respectively). CONCLUSION: Compared with patients with HPV-associated and HPV-independent/p53-normal PSCC, patients with HPV-independent/p53 abnormal PSCC have worse clinical outcomes. p53 IHC results define two prognostic categories in HPV-independent PSCC: HPV-independent/p53-normal tumors as low-risk tumors, whereas HPV-independent/p53-abnormal tumors as aggressive neoplasms.

Climate change is a global issue that draws widespread attention from the international society. As an important component of the climate system, the water cycle is directly affected by climate change. Thus, it is very important to study the influences of climate change on the basin water cycle with respect to maintenance of healthy rivers, sustainable use of water resources, and sustainable socioeconomic development in the basin. In this study, by assessing the suitability of multiple General Circulation Models (GCMs) recommended by the Intergovernmental Panel on Climate Change, Statistical Downscaling Model (SDSM) and Automated Statistical Downscaling model (ASD) were used to generate future climate change scenarios. These were then used to drive distributed hydrologic models (Variable Infiltration Capacity, Soil and Water Assessment Tool) for hydrological simulation of the Yangtze River and Yellow River basins, thereby quantifying the effects of climate change on the basin water cycle. The results showed that suitability assessment adopted in this study could effectively reduce the uncertainty of GCMs, and that statistical downscaling was able to greatly improve precipitation and temperature outputs in global climate mode. Compared to a baseline period (1961–1990), projected future periods (2046–2065 and 2081–2100) had a slightly decreasing tendency of runoff in the lower reaches of the Yangtze River basin. In particular, a significant increase in runoff was observed during flood seasons in the southeast part. However, runoff of the upper Yellow River basin decreased continuously. The results provide a reference for studying climate change in major river basins of China.

Ants of the genus Solenopsis are important invasive pests in the world. Due to their high dispersion capacity, aggressive behavior and because they feed on various sources of vegetable and animal protein, these insects have caused serious damage to public health and agriculture. The control has usually been carried out through the use of organosynthetic insecticides. However, due to the ecological and environmental impacts caused by the use these products, more sustainable alternatives have been sought for their control. Faced with these problems and due to the scarcity of registered products for the control of these insects, we aimed with this study to synthesize and evaluate the anticidal potential of carvacrol derivatives. The lethal and sublethal effects caused by these derivatives were compared with the essential oil of Lippia gracilis (50.7% carvacrol) and with the base molecule — carvacrol. Carvacryl benzoate was the most toxic derivative to Solenopsis sp. with an LD50 of 3.20 g/ mg. This compound was about 2 and 7.6 times, more toxic than carvacrol at the doses needed to kill 50 and 90% of populations, respectively. The workers of Solenopsis sp. showed a rapid reduction in survival when exposed to carvacrol (LT50 = 8.43h) and carvacryl benzoate (LT50 = 8.87h). Insects treated with sublethal doses of the compounds did not show significant effects on self-cleaning, allogrooming and aggregation, with the exception of those treated with L. gracilis essential oil. The oil increased self-cleaning and reduced allogrooming and aggregation. Ants treated with carvacrol and carvacryl benzoate showed greater distance and speed when compared to the control. These compounds decreased meanders and angular velocity. When live workers were exposed to dead individuals at the LD90 of the compounds, carvacryl benzoate was the derivative that most reduced insects survival, due to horizontal transfer. These results show the potential of the carvacrol derivative — carvacryl benzoate — for the alternative management of ants of the genus Solenopsis sp.

One of the industries with the fastest rate of growth is healthcare, and this industry's enormous data requires extensive cloud storage. The cloud may offer some protection, but there is no assurance that data owners can rely on it for refuge and privacy amenities. Therefore, it is essential to offer security and privacy protection. Increased customer satisfaction with security and privacy preservation is crucial since healthcare big data and its sources are stored in the cloud and contain increasingly private and sensitive information. However, maintaining privacy and security in an untrusted green cloud environment is difficult, thus the data owner should have complete data control. A new work SecPri-BGMPOP(security and privacy of Boost graph Convolutional Network -Pinpointing-Optimization Performance) is suggested that can offer a solution that involves several different steps in order to handle the numerous problems relating to security and protecting privacy. Initially Boost Graph Convolutional Network Clustering (BGCNC) algorithm, which reduces computational complexity in terms of time and memory measurements, is first applied to the input dataset to begin the clustering process. Second, enlarge by employing a piece of the magnifying bit string to generate a safe key, pinpointing based encryption avoids amplify leakage even if a rival or attacker decrypts the key or asymmetric encryption. Finally, to determine the accuracy of the method, an optimal key was created using a meta-heuristic algorithmic framework called Hybrid fragment horde bland lobo Optimization (HFHBLO). Our proposed method currently kept in a cloud environment, allowing analytics users to utilize it without risking their privacy or security.

A method was developed to perform shape optimization of a tidal stream turbine hydrofoil using a multi-objective genetic algorithm. A bezier curve parameterized the refrence hydrofoil profoil NACA 63815. Shape optimization of this hydrofoil maximized its lift-to-darg ratio and minimized its pressure coefficient, thereby increasing the turbines power output power and improving its cavitation characteristics. The Elitist Non-dominated Sorting Genetic Algorithm (NSGA-II) was employed to perform the shape optimization. A comparative study of two-and three-dimensional optimizations was carried out. The effect of varing the angle of attack on the quality of optimized results was also studied. predictions based on two-dimensional panel method results was also studied. Preditions based on a two-dimensional panel method and on a computational fluid dynamics code were compared to experimental measurments.

From June 18 to 19, 2013, the Ésera river in the Pyrenees, Northern Spain, caused widespread damage due to flooding as a result of torrential rains and sustained snowmelt. We estimate the contribution of snow melt to total discharge applying a snow energy balance to the catchment. Precipitation is derived from sparse local measurements and the WRF-ARW model over three nested domains, down to a grid cell size of 2 km. Temperature profiles, precipitation and precipitation gradient are well simulated, although with a possible displacement regarding the observations. Snowpack melting was correctly reproduced and verified in three instrumented sites, and according to satellite images. We found that the hydrological simulations agree well with measured discharge. Snowmelt represented 33% of total runoff during the main flood event and 23% at peak flow. The snow energy balance model indicates that most of the energy for snow melt during the day of maximum precipitation came from turbulent fluxes. This approach forecast correctly peak flow and discharge during normal conditions at least 24h in advance and could give an early warning of the extreme event 2.5 days before.

In the study of relativistic jets one of the key open questions is their interaction with the environment on the microscopic level. Here, we study the initial evolution of both electron–proton (e^- - p⁺) and electron–positron (e^±) relativistic jets containing helical magnetic fields, focusing on their interaction with an ambient plasma. We have performed simulations of "global" jets containing helical magnetic fields in order to examine how helical magnetic fields affect kinetic instabilities such as the Weibel instability, the kinetic Kelvin-Helmholtz instability (kKHI) and the Mushroom instability (MI). In our initial simulation study these kinetic instabilities are suppressed and new types of instabilities can grow. In the e^- - p⁺ jet simulation recollimation-like instability occurs and jet electrons are strongly perturbed. In the e^± jet simulation a recollimation-like instability occurs at early times followed by a kinetic instability and the general structure is similar to a simulation without helical magnetic field. Simulations using much larger systems are required in order to thoroughly follow the evolution of global jets containing helical magnetic fields.

Evaporating liquid sessile drop deposited on horizontal surface is an important object of applications (printing technologies, electronics, sensorics, medical diagnostics, hydrophobic coatings, etc.) and theoretical investigations (microfluidics, self-assembly of nanoparticle, crystallization of the solute, etc.). The arsenal of formulas for calculating the slow evaporation of an axisymmetric drop of capillary dimensions deposited on a flat solid surface is reviewed. Such characteristics as vapor density, evaporation flux density, total evaporation rate are considered. Exact solutions obtained in the framework of the Maxwellian model, in which the evaporation process of the drop is limited by vapor diffusion from the drop surface to the surrounding air, are presented. The summary covers both well-known results obtained during the last decades and new results published by us in the last few years, but practically unknown to the wide scientific community. The newest formulas, not yet published in refereed publications, concerning exact solutions for a number of specific contact angles are also presented. In addition, new approximate solutions are presented for the first time (total evaporation rate and mass loss per unit surface area per unit time in the whole range of contact angles ), which can be used in modeling without requiring significant computational resources.

Inteins, often referred to as protein introns, are highly mobile genetic elements that invade conserved genes throughout the tree of life. Inteins have been found to invade a wide variety of key genes within actinophages. While in the process of conducting a survey of these inteins in actinophages we discovered that one protein family of methylases contained a putative intein, and two other unique insertion elements. These methylases are known to occur commonly in phages as orphan methylases (possibly as a form of resistance to restriction-modification systems). We found that the methylase family is not conserved within phage clusters and has a disparate distribution across divergent phage groups. We determined that two of the three insertion elements have a patchy distribution within the methylase protein family. We also found that the third insertion element is likely a second homing endonuclease, and that all three elements (the intein, the homing endonuclease, and what we refer to as the ShiLan domain) all have different insertion sites that are conserved in the methylase gene family. Furthermore, we find strong evidence that both the intein and ShiLan domain are partaking in long distance horizontal gene transfer events between divergent methylases in disparate phage hosts within the already dispersed methylase distribution. The reticulate evolutionary history of methylases and their insertion elements reveals high rates of gene transfer and within-gene recombination in actinophages.

Ho Chi Minh City (HCMC), the most crowded city and economic hub of Viet Nam, has been experiencing land subsidence over the past decades. This effort aims to contribute the spatial distribution of subsidence in HCMC in its horizontal and vertical components using synthetic aperture radar interferometry (InSAR) time series. To this purpose, an advanced Persistent Scatterers and Distributed Scatterers (PSDS) InSAR technique was applied to two European Space Agency (ESA) Sentinel-1 datasets consisting of 96 ascending and 202 descending images, acquired from 2014 to 2020 over the HCMC area. A time series of 33 COSMO-SkyMed ascending images was also used for comparison. The combination of ascending and descending satellite passes is used to decompose the light of sight velocities into horizontal east-west and vertical components. Taking into account the presence of east-west horizontal motion, our findings indicate that the accuracy of the decomposed vertical velocity can be improved by up to 3 mm/year for Sentinel-1 data. The obtained results revealed that subsidence is most pronounced in the areas along the Sai Gon River, in the northwest-southeast axis, and in the southwest of the city, with a maximum value of 80 mm/yr, which is in accordance with the findings of the literature. The amplitude of east-west horizontal velocities is relatively small and large-scale eastward movement can be observed in the west of the city at a rate of 3-5 mm/yr. This confirmed that the displacement in Ho Chi Minh City area is mainly vertical downward. Together, these results reinforced the remarkable suitability of ESA's SAR Sentinel-1 for subsidence applications, even for non-European countries such as Vietnam and Southeast Asia.

The aim of this work is to evaluate the impact of proposed modifications to conventional capturing and discharging effluents devices in Subsurface Flow Wetland (SSFW) systems. Main modifications proposed consist on extending the influence of the capture and discharge device in such a way that the SSFW width and height are fully covered. Additionally an SSFW prototype was built as pilot including the proposed modifications and the impact of the innovative device is measured based on the efficiency of the Chemical Oxygen Demand (COD) removal as compared to a traditionally built SSFW. The results show that for the innovative device, the COD removal was 10% higher than for the conventional device.

Innovation is an essential key factor in the technology development history. Past research on innovation focused more on the innovation behavior of technology, but seldom described knowledge assets which also influence innovation behavior greatly. The effect of knowledge assets attribute and result on disruptive innovation is therefore regarded as the research topic in this study, where disruptive innovation is divided into outbound and inbound to combine combination-embeddednessandmajor business specificityof knowledge assets as the research model. Manufacturing enterprises in China are proceeded the questionnaire survey, and 173 valid copies are collected. The empirical analysis shows that combination-embeddedness of knowledge assets presents significantly positive effects on major business specificity and outbound innovationof an enterprise but reveals remarkably negative effects on inbound innovation. Enterprises are suggested to constantly accumulate knowledge assets with low major business specificity before disruptive innovation in order to reduce ineffective inbound innovation.

A modified free-wake vortex ring model is proposed to compute the dynamics of a floating horizontal-axis wind turbine. The model is divided into two parts. The near wake model uses a blade bound vortex model and trailed vortex model, which is developed based on vortex filament method. By contrast, the far wake model is based on the vortex ring method. The proposed model is a good compromise between accuracy and computational cost, for example when compared with more complex vortex methods. The present model is used to assess the influence of floating platform motions on the performance of a horizontal-axis wind turbine rotor. The results are validated on the 5MW NREL rotor and compared with other aerodynamic models for the same rotor subjected to different platform motions. It was found that the results from the proposed method are more reliable than the results from BEM theory especially at small angles of attack in the region of low wind speeds, on the one hand, and high wind speeds with blade pitch motions, on the other hand. And also the proposed method is less time consuming and has similar accuracy when comparing with more advanced vortex based methods.

(1) Background: This manuscript introduces the "Lines and Dots" (LAD) technique, a novel method for administering Botulinum Toxin Type A (BoNT-A) in treating horizontal forehead lines. This technique emphasizes precision in targeting nerve endplates, considering individual anatomical variations, and optimizing treatment efficacy. (2) Methods: The LAD technique focus on using the frontalis muscle contraction dynamics to identify the specific distribution of the supraorbital and supratrochlear nerves It involves creating a grid of predetermined lines and points on the forehead that align with nerve paths and motor endplate zones. (3) Results: By targeting injections along these precise lines and points, the LAD technique ensures more effective utilization of BoNT-A. This approach not only enhances the toxin's effect but also allows for a reduction in the overall dosage. The strategic placement of injections results in a more natural, symmetrical, and sustained therapeutic effect, ensuring an improved aesthetic outcome. (4) Conclusions: The LAD technique represents a significant advancement in the realm of cosmetic injectables. It offers a tailored, patient-specific approach, maximizing the effectiveness of BoNT-A injections for treating forehead lines while minimizing risks and enhancing patient satisfaction. This method underscores the importance of a deep anatomical understanding and precision in cosmetic procedures.

Horizontal transfer of transposons (HTT) is an important source of genomic evolution in eukaryotes. The HTT dynamics is well characterized in eukaryotes including insects however, but there is a huge gap of knowledge about HTT regarding many eukaryotes’ species. In this study we analyzed the events of the HTT between Rhus gall aphids (Hemiptera) and other insects. We analyzed the Mariner-like transposable elements (MLEs) belongs to Rhus gall aphids for the possible HT events. The MLEs have patchy distribution and have high similarity over the entire length of element with insects MLEs from different orders. We selected representative sequences from the Rhus gall MLEs and identified five events of HT between MLEs of Rhus gall aphids and other insects from five different orders. We also found multiple HTT events among the MLEs of insects from the five orders which demonstrate that these Mariner elements have been involved in recurrent HT between these six order of insects. Our current study closed the knowledge gap of HTT and reported the events between Rhus gall aphids and other insects for the first time. We believe that this study about HTT events will help to understand the evolution and spread of transposable elements in the genomes of Rhus gall aphids.

A novel drive current model covering the effects of source/drain voltage (VDS) and gate voltage (VGS) and incorporating drift and diffusion current on the surface channel at the nano-node level, especially beyond 28nm node is presented. The effect of the diffusion current added is more satisfactory to describe the behavior of the drive current in nano-node MOSFETs, fabricated with the atomic-layer-deposition (ALD) technology. This breakthrough in model establishment can expose the long and short channel devices together. Introducing the variables of VDS and VGS, the mixed current model more effectively and meaningfully demonstrates the drive current of MOSFETs under the operation of horizontal, vertical, or mixed electrical field. In comparison between the simulation and experimental consequences, the electrical performance is impressive. The error between both is less than 1%, better than the empirical adjustment to issue a set of drive current models.

COVID-19 is the most severe health crisis of the 21st century. COVID-19 presents a threat to almost all countries world-wide. The restriction of human mobility is one of the strategies used to control the transmission of COVID-19. However, it has yet to be determined how effective this restriction is in controlling the rise in COVID-19 cases, particularly in major capital cities such as Jakarta, Indonesia. Using Facebook's mobility data, our study explores the impact of restricting human mobility on COVID-19 case control in Jakarta. Our main contribution is showing how the restriction of human mobility data can give important information about how COVID-19 spreads in different places. We proposed modifying a global regression model into a local regression model by accounting for the spatial and temporal interdependence of COVID-19 transmission across space and time. We applied Bayesian hierarchical Poisson spatiotemporal models with spatially varying regression coefficients. We estimated the regression parameters using an Integrated Nested Laplace Approximation. We found that the local regression model with spatially varying regression coefficients outperforms the global regression model based on DIC, WAIC, MPL, and R2 criteria for model selection. In Jakarta's 44 districts, the impact of human mobility varies significantly. The impacts of human mobility on the log relative risk of COVID-19 range from –4.445 to 2.353. The prevention strategy involving the restriction of human mobility may be beneficial in some districts but ineffective in others. Therefore, a cost-effective strategy had to be adopted.

The Earth's fresh water resources predominantly is groundwater that is pumped out due to rapid urbanization and aggravated by climate change. Groundwater modeling is a crucial tool for understanding aquifer systems, employing 1D, 2D, and 3D numerical models with distinct applications. One-dimensional models focus on vertical dynamics, examining aquifer properties and simulating vertical contaminant transport. Two-dimensional models extend to regional scales, considering horizontal variations and assessing groundwater-surface water interactions, making them valuable for watershed-scale studies. Three-dimensional models provide a comprehensive representation of hydrogeological systems, capturing intricate flow patterns and aiding site-specific assessments. Comparative analysis reveals model strengths and limitations, emphasizing the importance of calibration for reliable results. Case studies showcase practical applications, such as 1D models in flooding analysis and 2D models for simulating debris flows. Three-dimensional modeling proves essential for understanding complex river-aquifer exchange fluxes. Future directions call for a global groundwater platform to address data variability and technical challenges. Despite substantial investments required, the anticipated returns in scientific advancements, societal benefits, and economic gains are expected to outweigh the initial costs. This review aims in highlighting the significance of advancing all three-dimension groundwater modeling for sustainable water resource management and environmental protection.

Steel fibres provides ductility to concrete structures. This in turn gives possibility to replace or reduce conventional reinforcement in structural elements. In this study the focus is on structural walls and the fibres as potential replacement for horizontal reinforcement in areas where vertical re-bars are needed. An experimental study was conducted, in which prismatic specimens with longitudinal re-bars were subjected to centric loading. Ten samples with 12 specimens in each were tested. The parameters considered were: fibre content, concrete cover for the longitudinal bars, and presence of stirrups. Self-compacting concrete with 30 and 60 kg/m3 steel fibres was used. The influence of fibres on maximum load, stiffness, and ductility of the specimens is evaluated. The results show that fibres eliminated brittle collapse and spalling of concrete at failure. Samples with fibres tend to have reduced maximum force and stiffness but increased ductility. The specimens with fibre content of 60 kg/m3 showed more ductile behaviour than the ones with minimum amount of conventional stirrups. The study suggests that combination of steel fibres and conventional re-bars can lead to less qualitative compactness of the self-compacting concrete, which in turn may reduce load bearing capacity and stiffness of the structure.

Drilling vibrations has been identified as a key performance limiter that prevents successful energy transfer from the surface to the bit. The resultant irregular bit rotation speed causes drilling challenges like poor hole quality and reduction in rate of penetration to name a few. Amongst other vibration suppression techniques, active control of vibrations is widely used and recommended. Active control system utilizes a closed loop feedback control to continuously adapt to downhole vibrations detected at the surface. The system requires regular tuning and upgrades which is done experimentally before field deployment. The paper presents a PID based experimental tuning of horizontal and vertical strings for irregular RPM. In doing so, the paper highlights the need of having horizontal experimental setups for state-of-the-art PID tuning for downhole RPM. The settling time of irregular RPM for horizontal setup is found to be lower than the vertical configuration due to multiple contact points and increased friction coefficient.

Genes coding for enzymes of the denitrification pathway appear randomly distributed among isolates of the ancestral genus Thermus, but only in few strains of the species T. thermophilus the pathway has been studied to a certain detail. Here, we review the enzymes involved in this pathway present in T. thermophilus NAR1, a strain extensively employed as a model for nitrate respiration, on the light of its full sequence recently assembled through a combination of PacBio and Illumina technologies in order to counteract the systematic errors introduced by the former technique. The genome of this strain is divided in four replicons, a chromosome of 2,021,843 pb, two megaplasmids of 370,865 and 77,135 bp and a small plasmid of 9,799 pb. Nitrate respiration is encoded in the largest megaplasmid, pTTHNP4, within a region that includes operons for O2 and nitrate sensory systems, a nitrate reductase, nitrate and nitrite transporters and a nitrate specific NADH dehydrogenase, in addition to multiple insertion sequences (IS), suggesting its mobility-prone nature. Despite nitrite is the final product of nitrate respiration in this strain, the megaplasmid encodes two putative nitrite reductases of the cd1 and Cu-containing types, apparently inactivated by IS. No nitric oxide reductase genes have been found within this region, although the NorR sensory gene, needed for its expression, is found near the inactive nitrite respiration system. These data clearly support that partial denitrification in this strain is the consequence of recent deletions and IS insertions in genes involved in nitrite respiration. Based on these data, the capability of this strain to transfer or acquire denitrification clusters by horizontal gene transfer is discussed.

In this study, a matched-mode autoregressive source depth estimation method (MMAR) based on autoregressive (AR) wavenumber estimation is proposed for a moving source in shallow water waveguides. The signal original frequency and the environmental parameters, namely, the sound speed profile and bottom properties are known as a prior knowledge. The mode wavenumbers are estimated by the AR modal wavenumber spectrum. On the basis of the mode wavenumber estimation, the mode amplitudes can be estimated by the wavenumber spectrum that is obtained by generalized Hankel transform. The source depth estimation is determined by the peak of source depth function wherein the data mode best matches the replica mode that is calculated using a propagation model. Compared with other methods of moving source depth estimation, the proposed method exhibits a better performance in source depth estimation under low signal-to-noise ratio or the small range span. The selection of horizontal line array depth is illustrated by simulation and normal mode theory in details.

Horizontal gene transfer (HGT) is the transmission of genes between organisms by other means than parental to offspring inheritance. While it is prevalent in prokaryotes, HGT is less frequent in eukaryotes and particularly in metazoan. Here, we propose Alienness, a taxonomy-aware web application that parses BLAST results against public libraries to rapidly identify candidate HGT in any genome of interest. Alienness takes as input the result of a BLAST of a whole proteome of interest against any NCBI protein library. The user defines recipient (e.g. metazoan) and donor (e.g. bacteria, fungi) branches of interest in the NCBI taxonomy. Based on the best BLAST E-values of candidate donor and recipient taxa, Alienness calculates an Alien Index (AI) for each query protein. An AI >0 indicates a better hit to candidate donor than recipient taxa and a possible HGT. Higher AI represent higher gap of E-values between candidate donor and recipient and a more likely HGT. We confirmed the accuracy of Alienness on phylogenetically confirmed HGT of non-metazoan origin in plant-parasitic nematodes. Alienness scans whole proteomes to rapidly identify possible HGT in any species of interest and thus fosters exploration of HGT more easily and largely across the tree of life.

Various risks and uncertainties are strengthening the downside of the global economy. This paper aims to estimate the impact of US-China conflict and the WTO Appellate Body's shutdown on global logistics demand and to show the seriousness of the situation. Existing literature studies on protectionism or US-China trade conflict, with a focus on the effects of specific issues or impact on bilateral relations. No research has considered the adverse effects of the WTO Appellate Body's shutdown. This paper considers both US-China conflict and the installation of new NTBs in other countries due to weakened WTO function, and tries to suggest that the combination of tariffs and NTBs can severely reduce international trade and the demand for maritime logistics services, making this paper differs from previous studies. This paper suggests that a catastrophe could occur in global maritime logistics, based on quantitative estimates for the impact of global protectionism. Finally, underlining that the international trade order should not seriously be damaged, this paper proposes that countries around the world should seriously discuss this issue at the 12th WTO Trade Ministers' Meeting in Kazakhstan June 2020.

A recent study by the Wall Street Journal reveals that the hydrofractured horizontal wells in shales have been producing less than forecasted by the industry with the empirical hyperbolic decline curve analysis (DCA). As an alternative to DCA, we introduce a simple, fast and accurate method of estimating ultimate recovery (EUR) in oil shales. We adopt a physics-based scaling approach to analyze oil rates and ultimate recovery from 14,888 active horizontal oil wells in the Bakken shale. To predict EUR, we collapse production records from individual horizontal shale oil wells onto two segments of a master curve: (1) We find that cumulative oil production from 4,845 wells is still growing linearly with the square root of time; and (2) 6,401 wells are already in exponential decline after approximately seven years on production. In addition, 2,363 wells have discontinuous production records, because of refracturing or changes in downhole flowing pressure, and are matched with a linear combination of scaling curves superposed in time. The remaining 1,279 new wells with less than 12 months on production have too few production records to allow for robust matches. These wells are scaled with the slopes of other comparable wells in the square-root-of-time flow regime. In the end, we predict that total ultimate recovery from all existing horizontal wells in Bakken will be some 4.5 billion barrels of oil. We also find that wells completed in the Middle Bakken formation, in general, produce more oil than those completed in the Upper Three Forks formation. The newly completed longer wells with larger hydrofractures have higher initial production rates, but they decline faster and have EURs similar to the cheaper old wells. There is little correlation among EUR, lateral length, and the number and size of hydrofractures. Therefore, technology may not help much in boosting production of new wells completed in the poor immature areas along the edges of the Williston Basin. Operators and policy-makers may use our findings to optimize the possible futures of the Bakken shale and other plays. More importantly, petroleum industry may adopt our physics-based method as an alternative to the overly-optimistic hyperbolic DCA that yields an "illusory picture" of shale oil resources.

All fundamental Planck scale symmetries are restored on a global level when a new charge is postulated in a finite, closed, Euclidean discrete space. Gravity emerges as a residual effect of the electromagnetic force in this scenario, resulting in a deterministic toy universe driven by a single input parameter. The model is developed using a constructive approach. Randomness is identified using a Chaintin argument. Aleph0 definite value is tied to the size of the universe. This is not an interpretation of Quantum Mechanics, but a deeper attempt to describe nature.

Background. Asbestos has been used for thousands of years but in a large industrial scale for about 100–150 years. The first identified disease was asbestosis, a type of incurable pneumoconiosis caused by asbestos dust and fibres. The latest estimate of global number of asbestosis deaths from the Global Burden of Disease estimate 2016 is 3495. Asbestos caused cancer was identified in the late 1930’s but despite of today’s overwhelming evidence of the strong carcinogenicity of all asbestos types including chrysotile it is still widely used globally. Various estimates have been made over time including those of WHO and ILO 107,000–112,000 deaths. Present estimates are radically higher. This special edition of the Journal summarizes key aspects of the past and present of the asbestos problem globally. Methods. Documentation on milestones of asbestos related diseases, ARDs, their recognition, reporting, compensation and prevention efforts were examined, in particular from the regulatory and prevention point of view. Estimated global numbers of incidence and mortality of ARDs were looked at. Results. Asbestos causes an estimated 257,000 deaths (243,223–270,635) annually according to latest knowledge. Work-related exposures are responsible for 235,000 deaths (222,322–247,363) of those. In the European Union, USA and in other High income economies (WHO regional classification) the direct costs for sickness, early retirement and death, including production losses, have been estimated to be very high, in the Western European countries and EU equivalent of 0.70% of the GDP or 114.9*109 USD. Intangible costs could be much higher. When applying the Value of Statistical Life (VSL) of 4 million EUR per cancer death used by the European Commission we arrived 5at 410*109 USD while the human suffering and loss of life is impossible to quantify. The numbers and costs are increasing practically in every country and region in the world. Asbestos has been banned in 55 countries but used widely today, some 2,030,000 tons consumed annually according to latest available consumption data. Every 20 tons of asbestos produced and consumed kills a person somewhere in the world. Buying 1 kg asbestos powder format e.g. in Asia costs some 0.38 USD and 20 tons would cost in such retail market 7600 USD. Conclusions. Present efforts to eliminate this man-made problem, in fact an epidemiological disaster, and preventing exposures leading to it are insufficient in most countries in the world. Applying programmes and policies, such as those on the elimination of all kind of asbestos use—that is banning of new asbestos use and tight control and management of existing structures containing asbestos—need revision and resources. The ILO/WHO Joint Programme for the Elimination of Asbestos-related Diseases need to be revitalized. Exposure limits do not protect properly against cancer but for asbestos removal and equivalent exposure elimination work we propose a limit value of 1000 fibres/m³.

This research explores the application of Support Vector Machine (SVM) and Digital Surface Models (DSM) derived from Unmanned Aerial Vehicle (UAV) data for a vertical-horizontal classification of mangrove ecosystems in Tongke-tongke and Samataring Village. The study focuses on integrating high-resolution DSM subtracted from Digital Terrain Models (DTM) to classify mangrove vegetation into sixteen distinct vertical-horizontal classes based on vegetation type and elevation. The analysis revealed that older mangroves, particularly those within the 25-35 meters elevation range, dominate the landscape, accounting for 43.40% of the total classified area. This dominance suggests a mature and ecologically stable mangrove ecosystem, which is crucial for biodiversity conservation and carbon storage. The study demonstrates the effectiveness of SVM and UAV technologies in providing detailed and accurate ecological assessments of mangrove forests. The classification results contribute valuable insights into the structural diversity and health of mangrove ecosystems, facilitating targeted conservation and management strategies. Additionally, the research highlights the utility of advanced remote sensing and machine learning techniques in enhancing the precision of environmental monitoring and the assessment of carbon sequestration capabilities within mangrove ecosystems. The findings underscore the potential of UAV-based remote sensing for ecological studies, offering a replicable method for similar assessments in other regions, thereby supporting global environmental management and climate action initiatives.

A linear stability analysis of the parallel uniform flow in a horizontal channel with open upper boundary is carried out. The lower boundary is considered as an impermeable isothermal wall, while the open upper boundary is subject to a uniform heat flux and it is exposed to an external horizontal fluid stream driving the flow. An eigenvalue problem is obtained for the two-dimensional transverse modes of perturbation. The study of the analytical dispersion relation leads to the conditions for the onset of convective instability as well as to the determination of the parametric threshold for the transition to absolute instability. The results are generalised to the case of three-dimensional perturbations.

This review highlights the potential and limitations of mRNA vaccines with a particular focus on mucosal delivery as an alternative to parenteral administration. The strengths of mRNA vaccines are: a) Versatility: they can be adapted to target a wide range of pathogens; b) Faster development: designed and produced more quickly than traditional vaccines; c) High efficacy: effective in preventing severe disease, as demonstrated during the COVID-19 pandemic. Current challenges: a) Delivery: current methods (mainly intramuscular injection) may not be optimal for inducing mucosal immunity; b) Stability: mRNA is fragile and needs to be protected from degradation; c) Safety: potential side effects, including myocarditis, blood clotting, allergic reactions need further investigation. Mucosal delivery could be more effective in preventing the transmission of pathogens and is generally better accepted by the population. Pros: offers the potential to induce local immunity at the site of pathogen entry, potentially providing broader protection; Cons: developing effective delivery systems and adjuvants for mucosal delivery is difficult. Extracellular vesicles as a mucosal delivery system are promising and offer a potentially safe, scalable, and needle-free approach. Future directions: a) Optimizing mRNA constructs: strategies like codon optimization and self-amplifying RNA can improve stability and translation efficiency; b) Rigorous pre-clinical studies are essential before human trials.

Health and well-being are a major concern for the elderly who experienced evacuation due to the 2011 Fukushima Daiichi Nuclear Power accident. This study examined the feasibility of a picture sound book with Ninja-essence to maintain or improve exercise habits and physical and mental conditions of the elderly affected by the Fukushima Daiichi Nuclear Power plant accident. We conducted a pre–post intervention study to evaluate a picture sound book with Ninja-essence for returnees and evacuees post lifting evacuation restrictions. In total, 29 people participated in this study. Residents in two groups, returnees and evacuees, were provided with the tool. Results of the pre–post changes were analyzed using descriptive statistics, i.e., Fisher’s exact test and t-test, and a significant difference was observed in both groups of participants between their left and right hand-grip strength, the maximum phonation time in the participants of the group that regularly engaged in exercise, and in the questions regarding swallowing exercises and singing songs or practicing words (p < 0.013 and 0.033); 16 of 29 participants reportedly enjoyed the program. The results demonstrated the future possibility of determining the improved outcome of this program in larger samples.

The horizontal flatbed electrophoresis system has been used for the electrophoresis of protein samples and is often preferred for a two-dimensional polyacrylamide gel electrophoresis. In currently available equipment, cathode and anode electrodes were placed on top of a gel at each end. An electric field entered from the top of a gel, and its strength was relatively weaker in the bottom part of the gel. Such configuration caused migrating protein bands to lie down forward in the migrating direction. New electrodes, i.e., the clamp-shaped and the double-deck electrodes, were developed to simultaneously apply an electric field from the top and bottom of a gel. Electrophoretic separation with these electrodes made protein bands more focused and improved protein band resolutions. When the FIGE technique was tested together with new electrodes, protein bands were aligned nearly vertically and showed the best electrophoretic resolutions.

As development progresses, when the bottom hole flowing pressure or formation pressure is less than the saturation pressure of crude oil in the reservoir, oil and gas two-phase seepage occurs in the reservoir. Due to the characteristics of oil and gas two-phase seepage, after the oil and gas two-phase seepage occurs in the reservoir, the well production will be reduced, or even greatly reduced. Therefore, how to predict the horizontal well capacity better in this case is an important problem that needs to be solved urgently. In this paper, the method and process of establishing the transient calculation model of two-phase flow in horizontal wells are introduced in detail from three aspects: fluid physical properties, reservoir oil-gas two-phase seepage, and the coupling model of Inflow Performance and Flow in Wellbore. The model is more reliable through the verification of production data from five wells in two oilfields.

Artificial Intelligence (AI) tools and techniques are comparatively recent advances of present-day globalized world. With their easy availability and friendly user interface AI has affected every sphere of human being. These tools are increasingly becoming popular because of the numerous benefits occurred to the society in many ways. However, there are not only the positive side of these technologies, but also many negative sides. Along with the development and adoption of AI, cyber-attacks are increased and disrupting the information system. Threat actors may misuse artificial intelligence. Hence, these tool designers are working and applying the ability of generative AI can tip the scales in cybersecurity. So, in the age of AI, there is always tension between the cyber attackers and the defenders to make a balanced information system. It is a general rule that defenders must be well in advance in their favor and keep ahead of adversaries. The United National and several governments for example the US, UK, and the big AI giants like Microsoft along with OpenAI, are working on emerging cyberattacks. This research paper explores the concept of information resilience in ML and AI systems, focusing on strategies to enhance their ability to withstand uncertainties, adversarial attacks, and data perturbations.

Landsat and Sentinel-2 acquisitions are among the most widely used medium-resolution optical data adopted for terrestrial vegetation applications, such as land cover and land use mapping, vegetation condition and phenology monitoring, and disturbance and change mapping. When combined, both data archives provide over 40 years, and counting, of continuous and consistent observations. Although the spatio-temporal availability of both data archives is well-known at the scene level, information on the actual availability of cloud-, snow-, and shade-free observations at the pixel level is lacking and should be explored individually for each study to correctly parametrize subsequent analyses. However, data exploration is time and resource consuming, thus is rarely performed a-priori. Consequently, the spatio-temporal heterogeneity of usable data is often inadequately accounted for in the analysis design, risking ill-advised selection of algorithms and hypotheses, and thus inferior quality of final results. Here we present precomputed data on the daily 1982‑2023 availability of usable Landsat and Sentinel-2 acquisitions across the globe, sampled at a pixel-level in a regular 0.18°-point grid. The dataset comprises separate Landsat- and Sentinel‑2‑specific data records, and is accompanied by a pixel-specific growing season information to facilitate data exploration. The dataset was derived based on freely available 1982-2023 Landsat surface reflectance (Collection 2) and Sentinel-2 top-of-the-atmosphere reflectance (pre‑Collection-1 and Collection-1) scenes from 2015 through 2023, following the methodology developed in the recent study on data availability over Europe [1]. Growing season information was derived based on 2001‑2019 time series of the yearly 500 m MODIS land cover dynamics product (MCD12Q2; Collection 6) [1]. As such, the dataset presents a unique overview of the spatio-temporal availability of usable daily Landsat and Sentinel-2 data at the global scale, hence offering much needed a-priori information aiding identification of appropriate methods and challenges for terrestrial vegetation analyses at local to global scale.

Global financial investments in energy production and consumption are significant since all aspects of a country's economic activity, and development require energy resources. In this paper, we assess the investment trends in the global energy sector during, before and after financial crises of 2008 using two data sources: (1) Dealogic database providing cross‐border mergers and acquisitions (M&As), and (2) fDi Intelligence fDi Markets database providing greenfield (GF) foreign direct investments (FDIs). We highlight the changing role of China and compare its M&A and GF FDI activities to those of the United States, Germany, UK, Japan and others during this period. We analyze the investments along each segment of the energy supply chain of these countries to highlight the geographical origin and destination, sectoral distribution, and cross‐border M&As and GF FDI activities. Our paper shows that while energy accounts for nearly 25% of all GF FDI, it only accounts for 4.82% of total M&A FDI activity in the period 1996-2016. China's outbound FDI in the energy sector started its ascent around the time of the global recession and had accelerated in the post-recession phase. In the energy sector, the development of China's outbound cross‐border M&As is similar to USA or UK, located mostly in the developed countries in the west, while their outbound GF investments are spread across many countries around the world. Also, China's outbound energy M&As are concentrated in certain segments (extraction, and electricity generation) while their GF covers all segments of the energy supply chain.

Abstract: Coal bed methane (CBM) reservoirs are complex systems whose properties differ from those of conventional reservoirs. Coal seams are dual-porosity systems that comprise the porosities of the matrix and cleat system. Gas in the coal seams can be stored as free gas in the cleat system and as adsorbed gas in the porous medium. The flow mechanisms of the natural gas through the formation include desorption, diffusion, and Darcy’s flow regimes. The permeability of CBM reservoirs is more sensitive to pressure variations than conventional gas reservoirs. To study the flow behavior of CBM reservoirs it is mandatory to use a model that considers their unique characteristics. The objective of this study was to propose a physical and mathematical model of production performance for horizontal wells in CBM reservoirs whose permeability is dependent on pressure. A solution for the model was obtained by applying Pedrosa´s transformation, perturbation theory, Laplace transformation, the point source method, and Sthefest´s algorithm. The solution to this problem was validated with previous work thoroughly. The type curves of the model were built and the pressure transient behavior of the model was analyzed and discussed. The effects of several parameters on pressure behavior were also discussed.

Drops are the most important and most common energy dissipator in irrigation networks and erodible canals and consequently, their performance must be well understood. This study was designed to evaluate the capability of Artificial Intelligence (AI) methods including ANN, ANFIS, GRNN, SVM, GP, MLR, and LR to predict the relative energy dissipation (∆E/E0) in vertical drops equipped with a horizontal screen. For this study, 108 experiments were carried out to investigate energy dissipation with variable discharge, varying drop height, and porosity of the horizontal screens. Parameters yc/h, yd/yc, and p are considered as input variables and ∆E/E0 is the output variable. The efficiency of models was compared using Taylor's diagram, Box Plot of the applied error distribution, correlation coefficient (CC), mean absolute error (MAE) and root-mean-square error (RMSE). Results indicate that the performance of the ANFIS_gbellmf based model with CC value of 0.9953, RMSE value of 0.0069 and MAE value of 0.0042 was superior to other applied models. Also, the linear regression model with CC=0.9933, RMSE=0.0083, and MAE= 0.0067performs better than the multiple linear regression model in this study. Results of a sensitivity study suggest that yc/h is the most effective parameter for predicting ∆E/E0.

This paper numerically investigates a 3D mesh independency study of a straight blade horizontal axis tidal turbine modelled using Computational Fluid Dynamics (CFD). The solution was produced by employing two turbulence models, the standard k-ε model and Shear Stress Transport (SST) in ANSYS CFX. Three parameters were investigated: mesh resolution, turbulence model, and power coefficient in the initial CFD, analysis. It was found that the mesh resolution and the turbulence model affect the power coefficient results. The power coefficients obtained from the standard k-ε model are 15% to 20% lower than the accuracy of the SST model. It can also be demonstrated that the torque coefficient increases with the increasing Tip Speed Ratio (TSR), but drops drastically after TSR = 5 and k-ε model failing to capture the non-linearity in the torque coefficient with the increasing TSR.

This study conducted experiments to optimize the electro-dewatering of sludge using a dynamic model calculation method and the Wild Horse optimizer. Specifically, we explored two factors that might influence dewatering: the composition of the electrode materials and the strength of the electrical field. Compared to other electrodes commonly used in electro-dewatering—such as RuO2/Ir2O3-Ti, graphite, Ir2O3/Ta2O5-Ti, and Ti—the Electro-kinetic Geosynthetics (EKG) electrode exhibited superior performance. This was determined by considering both energy consumption and model establishment. Our findings also identified electric-field strength as a crucial factor determining the final moisture content. As the electrical intensity increased, the dewatering effect improved, aligning with our model calculations. However, we observed a steep increase in energy consumption per kilogram of filtrate when the electric-field strength exceeded a certain threshold. To optimize the energy consumption of the dehydration process, we constructed a multi-factor model. The simulation results from this model confirmed that electric-field intensity is the primary factor affecting dehydration. It was established that 10 V/cm is a critical threshold for the process.

As the COVID-19 pandemic has caused enormous damage to society, economy and public health security, it is crucial to combat the epidemic and allocate social and health resources effectively. Global optimization algorithms are extensively used in many domains to find optimal solutions to complex problems. Thus, a survey of three typical global optimizations applied on the COVID-19 pandemic is timely. This article is structured into three typical global optimization algorithms - Genetic Algorithm, Particle Swarm Optimization, and Cat Swarm Optimization - and summarizes the framework models and practical applications, as well as other optimization methods that may be applied to COVID-19. Finally, current unresolved challenges and future research opportunities to be explored are summarized.

This paper looks at key elements of global culture that are driving a new paradigm shift in museums causing them to question their raison d'être, their design and physical space, recognizing the need to accommodate visitor interaction and participation, and to reprioritize institutional outcomes and goals reexamining their priorities. As heritage sharing in online spaces reaches across national, political, and social boundaries on platforms and networks, this has been driven by museum engagement with Internet life during the pandemic. Museum relationships and interactions with communities both local and global, continue to challenge core values and precepts, leading to radical changes in how museums define their roles and responsibilities. In this new cultural landscape, museums are responding to human digital identity in a tidal wave of human interactions on the Internet, from social media to online sharing of images and videos. This is revealing shared perspectives on cultural conflict as being tied to freedom of expression of one’s heritage embedded in digital identity.

This new study revised interlinked issues of global soil organic carbon (SOC), annual net primary productivity (NPP) and atmospheric CO₂ turnover time (τ). Soil is confirmed as both the greatest sink and source for excess atmospheric CO₂. Most terrestrial NPP (~218 Gt C/yr) is ultimately processed in topsoil and SOC stocks now total >10,000–12,000 Gt. More excess carbon is released into the air and water from SOC loss (>20 Gt C/yr) due to land clearance for pasture/crops, fires, agrichemical poisoning and erosion, than from fossil fuels (~10 Gt C/yr). NOAA’s Barrow bounce and isotopic analyses support high terrestrial flux up to ~800 Gt C/yr and CO₂ turnover time of ~1–4 years. Earth’s re-humification via compost offers the best and only practical/time-critical fix for climate, strategy for species extinction plus remedy for human health.

: Two-dimensional instability of a horizontal layer of boiling liquid with a finite height is experimentally studied. In this layer, “vapor columns” rose at the corners of a square rectangular grid. The symmetry of “vapor column” location on the heating surface is considered. The model considers the approach to the boiling crisis in terms of both developed nucleate boiling and transitional boiling (the Zuber problem). When dealing with developed nucleate boiling, the layer of boiling liquid is considered in calculations as an isotropic homogeneous system (foam). It is shown how the conditions on the heating surface (capillary-porous coating) affect external hydrodynamics of the liquid layer and, ultimately, the value of the critical heat flux. The calculation ratio obtained by approaching the boiling crisis with regard to developed nucleate boiling takes into account the dependence of the critical heat flux on the void fraction of the boiling liquid layer. A new solution to the boiling crisis problem is proposed when approaching the crisis from the point of transitional boiling (the Zuber problem). This new solution eliminates some shortcomings of the classical problem (in particular, the void fraction of the layer corresponds to the experiments).

Gastrodia pubilabiata is a nonphotosynthetic and mycoheterotrophic orchid belonging to subfamily Epidendroideae. Compared to other typical angiosperm species, the plastome of G. pubilabiata is dramatically reduced in size to be only 30,698 base pairs (bp). This reduction has led to the loss of most photosynthesis-related genes and some housekeeping genes in the plastome, which now only contains 19 protein coding genes, three tRNAs, and three rRNAs. This study decoded the entire mitogenome of G. pubilabiata, which consisted of 44 contigs with a total length of 867,349 bp. Its mitogenome contained 38 protein coding genes, nine tRNAs, and three rRNAs. To determine possible gene transfer events between the plastome and the mitogenome, individual BLASTN searches were conducted, using all available orchid plastome sequences and flowering plant mitogenome sequences. Plastid rRNA fragments were found at a high frequency in the mitogenome. Seven plastid protein coding gene frangments (ndhC, ndhJ, ndhK, psaA, psbF, rpoB, and rps4) were also identified in the mitogenome of G. pubilabiata. Phylogenetic trees using these seven plastid protein coding gene fragments suggested that horizontal gene transfer (HGT) from plastome to mitogenome occurred before losses of photosynthesis related genes, leading to the lineage of G. pubilabiata. Compared to species phylogeny of the lineage of orchid, it was estimated that HGT might have occurred approximately 30 million years ago.

In this paper, a further mathematical analysis of some previous results of the author’s ongoing investigation regarding Prandtl’s equations is accomplished. In particular, the objective of the present work is the performance of an approximate explicit solution to Prandtl’s system of equations for a laminar, isothermal, incompressible and steady boundary layer flow of a Newtonian fluid, over an infinite horizontal flat plate.

This study aimed to overcome the difficulty of conducting the horizontal-well cavity leaching test in the field and to investigate the long-term stability of the horizontal-well salt-cavity natural gas storage. The simulation test design is combined with the similarity theory to study the cavity expansion characteristics and the influence law of cavity leaching parameters. Through the design of a rubber hose connection, an integrated closed test system for multi-stage horizontal-well cavity leaching and brine drainage was built. The test system also realises the repeatable backward movement of the injection well during the test. A similarity simulation of the test design was carried out, and the test platform was constructed to carry out multi-stage horizontal-well leaching tests with a nitrogen cushion. In the horizontal-well leaching tests with a nitrogen cushion, the influence laws of the well spacing, flow rate and liquid level position on cavity expansion were investigated. Based on the morphological characteristics of the horizontal-well cavity, a numerical model of the horizontal-well salt cavity was developed, which reflects the real cavity morphology leached in the test. The long-term stability of the horizontal-well salt-cavity natural gas storage under different internal pressures was investigated through numerical simulation.

Abstract: The aim of this study was to evaluate the effects of solids accumulation on greenhouse gas (GHG) emissions, substrate, plant growth and performance of a horizontal flow (HF) treatment wetland (TW) planted with Phragmites australis (Cav.) Trin. ex Steud. sub sp. australis. The study was carried out in an eight-year-old full-scale HF-TW located in the Mediterranean region (Sicily, Italy). To collect data inside the HF unit, nine observation points (besides the inlet and the outlet) along three 8.5 m long transects (T1, T2, and T3) were identified. The first transect (close to the inlet zone) showed hydraulic conductivity (Ks) reduction of about one order of magnitude higher than the other two. Results highlighted GHG emissions increasing during the summer when temperature and solar radiation were higher than in the rest of the year. Carbon dioxide (CO2) emis-sions decreased from T1 to T3, with maximum monthly values in T1 (21.4 g CO2 m-2 d-1) about double with respect to T2 (12.6 g CO2 m-2 d-1) and T3 (10.7 g CO2 m-2 d-1) observed in July. The CO2 seasonal trend was similar to that of P. Australis growth. Theoretical me-thane (CH4) emissions followed the trend of volatile solids (VS), which was about 3.5 and 4 times in T1 to T2 and T3. The highest CH4 emissions in T1 were probably due to anaerobic bacteria (methanogens) that proliferated in the waterlogged, anoxic part of TW. The pore-clogging affected the chemical oxygen demand (COD) removal efficiency which de-creasing from T1 to T3 for the observation period. Notwithstanding this behaviour, the final effluent quality was very satisfactory with the average value of COD removal efficiency above 90%.