Headspace solid phase microextraction (HS-SPME) coupled to gas chromatography-mass spectrometry is widely employed for volatile analyses of plants, including mapping populations used in plant breeding research. Studies often employ a single internal surrogate standard, even when multiple analytes are measured, with the assumption that any relative changes in matrix effects among individuals would be similar for all compounds, i.e. matrix effects do not show Compound × Individual interactions. We tested this assumption using individuals from two plant populations, an interspecific grape (Vitis spp.) mapping population (n = 140) and a tomato (Solanum spp.) recombinant inbred line (RIL) population (n = 148). Individual plants from the two populations were spiked with a cocktail of internal standards (n = 6, 9, respectively) prior to HS-SPME-GC-MS. Variation in the relative responses of internal standards indicated that Compound × Individual interactions exist but were different between the two populations. For the grape population, relative responses among pairs of internal standards varied considerably among individuals, with a maximum of 249% relative standard deviation (RSD) for the pair of [U13C]hexanal and [U13C]hexanol. However, in the tomato population, relative responses of internal standard pairs varied much less, with pairwise RSDs ranged from 8% to 56%. The approach described in this paper could be used to evaluate the suitability of using surrogate standards for HS-SPME-GC-MS studies in other plant populations.

Tea (Camellia sinensis) is one of the most popular beverages worldwide. Many types of tea prod-ucts continuously emerge in an endless stream; so, the classification or verification of tea be-comes more difficult. Aroma is a vital indicator of tea quality. The present study deals with the identification of aroma compounds in 18 different kinds of tea belonging to three typical tea va-rieties, including green tea, oolong tea, and black tea, using GC-IMS and GC×GC-O-MS. More-over, the clustering of all 18 tea samples and the in-depth correlation analysis between sensory evaluation and instrumental data were performed using the PCA and OPLS-DA. The results re-vealed that in all 18 kinds of tea, a total of 85 aroma compounds were detected by GC-IMS, whereas 318 were detected by GC×GC-O-MS. The PCA result revealed that green tea, oolong tea, and black tea could be clearly separated based on their peak areas. The OPLS-DA result showed that a total of 49 aroma compounds with VIP value > 1.0 could be considered as the potential in-dicators to quickly classify or verify tea types. This study not only compared the aroma differ-ences across different types of teas, but also provided ideas for the rapid monitoring of tea qual-ity and variety.

Scientific advancements in the food industry have resulted in the discovery of natural substances that can serve various functions in food. Essential oils, in particular, can act as food preservatives or flavoring agents due to their abundance of natural antioxidants, which possess preservative properties. In this study, the composition of Thymus vulgaris essential oil was determined using GC-MS and HS-SPME. The essential oil obtained from Thymus vulgaris L. through hydro-distillation yielded approximately 4%. GC/MS analysis of the essential oil identified 11 components, with a predominant presence of oxygenated monoterpenes (56.97%). Notably, carvacrol (37.63%) and thymol (17.35%) were present in significant amounts, accounting for 54.98% of the overall composition. The in vitro antioxidant activity of the essential oil was evaluated using three methods. The DPPH free radical scavenging test yielded an IC50 of 0.51±0.11 mg mL-1. The β-carotene/linoleic acid bleaching test resulted in an IC50 of 2.58±0.10 mg mL-1. Finally, the ABTS assay indicated relatively lower antioxidant activity compared to ascorbic acid.

A rapid and efficient technique using an electronic nose based on a mass detector combined with headspace sampling (HS-SPME-MS e-nose) and chemometric tools was applied to classify beer samples between fresh and aged and between samples contained in aluminium cans or glass bottles, and to predict the shelf life of beer. The mass spectra obtained from the HS-SPME-MS e-nose contain information on the volatile compounds, recorded as the abundance of each ion at different mass-to-charge (m/z) ratios. The analysis was performed on 53 samples aged naturally for eleven months in the absence of light and with a controlled temperature of around 14° C +/- 0.5° C. Principal Component Analysis (PCA) was performed on the data, showing a grouping of samples between fresh and aged. Partial Least Square Discriminant Analysis (PLS-DA) allowed discriminating fresh from aged beers but was not able to discriminate samples packaged in aluminium cans or in glass bottles. Finally, Partial Least Square Regression (PLSR) was applied to build a prediction model and showed to be effective to predict beer shelf life.

Waterford Blaa is one of only seven Irish Protected Geographical Indication (PGI) products and the only Irish PGI bread. Currently, there are few published data characterising these products. This study aimed to determine whether any compositional or sensory markers could be used to differentiate between the three authorised producers of Waterford Blaa. Compositional testing was completed using AOAC standard methods; colour of top crust, bottom crust and crumb were identified with the Minolta Hunter lab colorimeter and texture profile analysis (TPA) was completed with an 80% compression test using the Instron 5544 to establish hardness, gumminess, and springiness. The fatty acid and aroma profiles were established in triplicate testing for the three authorised Blaa products using gas chromatography-flame ionisation detection and headspace-solid phase micro extraction-gas chromatography-mass spectrometry, respectively. As expected, results showed little variation in the overall composition of Waterford Blaa products. However, this study identified a unique fatty acid profile/volatile aroma profile for each Blaa. Specifically, the volatile profile showed potential differentiation between Blaa’s in terms of pentanal, furfural, 2-furanmethanol, 2-ethyl-1-hexanol and 2-pentyl furan. In addition, levels of hexanal and ethyl acetate were significantly different (p<0.05) in the crumb section of all three Blaa’s. This unique fingerprint has the potential to be used to identify fraudulent products claiming to be Waterford Blaa.

The genus Beauveria include important entomopathogenic and endophytic fungi, among them, Beauveria bassiana is the most studied species. However, there are few knowledge regarding their antimicrobial activity. The current research has been conducted to evaluate in vitro antagonistic activity of B. bassiana and the antimicrobial efficacy of its Exo and Endo metabolites against Bacillus cereus, B. megaterium, Clavibacter michiganensis (gram positive bacteria, G+ve), Xanthomonas campestris, Pseudomonas aeruginosa and P. fluorescence (gram negative bacteria, G-ve). In addition, Solid-phase microextraction (SPME) was coupled to Gas Chromatography-Mass Spectrometry (GC/MS) to qualitatively measure the volatile organic compounds (VOCs) metabolic profile of the most efficient studied isolate of B. bassiana. The obtained results showed that, the isolate UniB2439-3 has promising antibacterial effect against most of studied target bacteria. SPME-GC/MS analysis of VOCs revealed the presence of ethanol; butanal,2-methyl; 2,4-dimethyl-1-heptene; octane, 4-methyl and β-elemene as the main dominant bioactive compounds. The outgoing results explicated that the efficient isolate of B. bassiana can be potentially used as a biocontrol agent against several bacteria especially G+ve ones.

Glycosidic linkage analysis was conducted on the unfractionated polysaccharides in the alcohol-insoluble residues (AIRs) prepared from six red seaweeds (Gracilariopsis sp., Prionitis sp., Mastocarpus papillatus, Callophyllis sp., Mazzaella splendens, and Palmaria palmata) using GC-MS/FID analysis of partially methylated alditol acetates (PMAAs). The cell walls of P. palmata primarily contained mixed-linkage xylans and small amounts of sulfated galactans and cellulose. In contrast, the unfractionated polysaccharides of the other five species were rich in galactans displaying diverse 3,6-anhydro-galactose and galactose linkages with varied sulfation patterns. Different levels of cellulose were also observed. This glycosidic linkage method offers advantages for cellulose analysis over traditional monosaccharide analysis that is known for underrepresenting glucose in crystalline cellulose. Relative linkage compositions calculated from GC-MS and GC-FID measurements showed that anhydro sugar linkages generated more response in the latter detection method. This improved linkage workflow presents a useful tool for studying polysaccharide structural variations across red seaweed species. Furthermore, for the first time, relative linkage compositions from GC-MS and GC-FID measurements, along with normalized FID and total ion current (TIC) chromatograms without peak assignments, were analyzed using principal component analysis (PCA) as a proof-of-concept demonstration of the technique's potential to differentiate various red seaweed species.

In this study, the use of recycled diatomaceous earth as the extraction phase in a the solid phase microextraction (SPME) technique for the determination of polycyclic aromatic hydrocarbons (PAHs) in river water samples, with separation/detection performed by gas chromatography-mass spectrometry (GC-MS), is proposed. The optimized extraction conditions are extraction time 70 min at 80 ºC with no addition of salt. The limits of quantification were close to 0.5 μg L-1 with RSD values lower than 25% (n = 3). The linear working range was 0.5 μg L-1 to 25 μg L-1 for all analytes. The method was applied to samples collected from the Itajaí River (Santa Catarina, Brazil) and the RSD values for repeatability and reproducibility were lower than 15% and 17%, respectively. The efficiency of the recycled diatomaceous earth fiber was compared with that of commercial fibers and good results were obtained, confirming that this is a promising option for use as the extraction phase in SPME.

Bioprospecting native Australian plants offers potential discovery of latent and novel bioactive compounds. Promising cytotoxic and antibacterial activity of methanolic extracts of Pittosporum angustifolium and Terminalia ferdinandiana led to further fractionation and isolation using our laboratory’s bioassay guided fractionation protocol. Hence, the aim of this study was to further evaluate the bioactivity of the fractions and subfractions and characterize bioactive compounds using liquid chromatography mass spectroscopy (LC-MS/MS) and gas chromatography MS (GC-MS). Compounds tentatively identified in P. angustifolium Fraction 1 using LC-ESI-QTOF-MS/MS were chlorogenic acid and/or neochlorogenic acid, bergapten, berberine, 8’-epitanegool and rosmarinic acid. GC-MS analysis data showed the presence of around 100 compounds, mainly comprising of carboxylic acids, sugars, sugar alcohols, amino acids, and monoalkylglycerols. Furthermore, the fractions obtained from T. ferdinandiana flesh extracts showed no cytotoxicity, except against HT29 cell lines, and only Fraction 2 exhibited some antibacterial activity. The reduced bioactivity observed in the T. ferdinandiana fractions could be attributed to the potential loss of synergy as compounds become separated within the fractions. As a result, further fractionation, and separation of compounds in these samples were not pursued. However, additional dose-dependent studies are warranted to validate the bioactivity of T. ferdinandiana flesh fractions, particularly since this is an understudied species. Moreover, LC-MS/GC-MS studies confirm the presence of bioactive compounds in P. angustifolium Fraction 1/subfractions which helps to explain the significant acute anti-cancer activity of this plant. The screening process designed in this study has the potential to pave the way for developing scientifically validated phytochemical/bioactivity information on ethnomedicinal plants, thereby facilitating further bioprospecting efforts, and supporting the discovery of novel drugs in modern medicine.

Metabolomic analysis of biological fluids and tissues has become an increasingly routine tool in the biological toolbox. However, challenges remain to be overcome, including developing strategies to maximise coverage of the metabolome without requiring large sample volumes. Here we describe a multimodal strategy that combines data using both LC-MS and GC-MS from a unique vial with a sample of plasma (20µl) or a sample of brain tissue (3mg). Using a split phase extraction the non-aqueous phase was analyzed by reversed phase (RP) LC-MS, whilst the aqueous phase was analyzed using hydrophilic liquid interaction chromatography (HILIC)LC-MS, with both phases also analysed using GC-MS after derivatization of the extract. Analytical performance was assessed in 7 rat cerebellum samples and a pilot study of 40 plasma samples (20 vs. 20: AD vs. healthy controls). The method, which uses four hours of instrument time, measured 20,707 metabolite features in brain samples and 17,266 in plasma samples, from those 44.1% features displayed CV’s below 15% and 75.2% below 30%. The method has potential to resolve subtle biological differences and to correlate metabolite composition directly to clinical outcomes including MMSE, age and ADCS-ADL. This method can acquire in the order of 20K metabolic features when low volumes are available.

This study presents an innovative analytical method for the detection and quantification of 14 β-agonists in pork using liquid chromatography-tandem mass spectrometry (LC-MS/MS). The method involves the use of a solid phase microextraction (SPME) probe, consisting of a wooden tip coated with polyacrylonitrile (PAN) and molecularly imprinted polymer (MIP). This probe has been integrated into an automated extraction device, designed in our laboratory to extract the target analytes prior to LC-MS/MS analysis. Compared to the traditional solid-phase extraction (SPE) procedure, the proposed approach significantly reduces the costs related to adsorbent ma-terial and solvent consumption, and shortens purification time, thereby reducing both the tech-nical workload and associated expenses. The methodology has been carefully validated in ac-cordance with the National Standard of the People's Republic of China (GB/T 22286-2008), evalu-ating key parameters including the limit of detection (LOD), limit of quantification (LOQ), matrix effects, linearity, and both intra-day and inter-day precision. The average recovery rates for all β-agonists were observed to lie between 71.6% and 82.2%, with relative standard deviations (RSDs) consistently below 15% for both types of precision. The LOD and LOQ values were found to range from 0.09 to 0.39 μg/kg and 0.27 to 0.99 μg/kg, respectively. In terms of accurate detection of positive samples, the developed method demonstrated a closer approximation to the true value of the sample compared to the National Standard method GB/T 31658.22-2022. Overall, the proposed method exhibits substantial promise for the routine assessment of β-agonists in pork and presents a practical alternative for compliance monitoring in regulatory settings.

Gasca D herbal formulation is an antidiabetic medicine for the management of diabetes mellitus produced exclusively from natural ingredients. The level of some essential elements (Copper, chromium, Cobalt, Iron, Manganese, Nickel and zinc) and toxic (Cadmium, Arsenic, Mercury, and Lead) heavy metals were determined using microwave plasma-atomic emission spectrometry (MP-AES). The aim of this study is to evaluate the levels of essential and toxic heavy metals and also identify bioactive compounds present in Gasca D herbal formulation. The result shows no traces of Lead, Mercury, Zinc, Arsenic and Zinc, Iron was found to have highest concentration 67.16 + 7.5 µg/g and Cadmium lowest concentration 0.4 + 0.03µg/g. GC-MS analysis of Gasca D herbal formulation revealed the presence of 14 biologically active compounds which include N-Formyl-beta-alanine, Paromomycin, 3,4-Altrosan, Benzamide, 1,3,4-Thiadiazol-2-amine, Carbamodithioic acid, Carbonic acid, alpha-D-Glucopyranoside, Ethyl isocyanide, 2-Propanesulfinic acid, Propanamide, 2-Butenenitrile, Dicyclopropyl carbinol, Isoxazolidine, 1,5-Hexadiene 10-Azido-1-decanethiol. Conclusion: The result indicates that the mean levels of toxic metals in Gasca D herbal formulation were below WHO permissible levels. Gasca D herbal formulation also contains various bioactive compounds that can have various medicinal application which can be used for the treatment of various diseases.

Volatile organic compounds (VOCs) released from plants have been correlated with disease-status. Analysis of VOCs using GC-MS is time-consuming, laboratory-based, and requires specialist training. Electronic nose devices (E-nose) provide a portable alternative. Three different E-nose devices were compared to assess how accurately they could detect Mango Twig Tip Dieback and Panama disease in banana. The devices were initially trained on known volatiles, then pure cultures of Pantoea sp., Staphylococcus sp., and Fusarium odoratissimum, and finally, on infected and healthy mango leaves and field-collected, infected banana pseudo-stems. The experiments were repeated three times with six replicates for each host-pathogen pair. The variation between healthy and infected host materials was evaluated by principal component and linear discriminant analysis, cross-validation and chemometric data analysis. GC-MS analysis was conducted contemporaneously and identified an 80% similarity between healthy and infected plant material. The portable C 320 was 100% successful in discriminating known volatiles but had a low capability in differentiating healthy and infected plant substrates. The advanced devices (PEN 3 / MSEM 160) successfully detected healthy and diseased samples with a high variance. The results suggest that E-nose devices are more sensitive and accurate in detecting changes of VOCs between healthy and infected plants compared to headspace GC-MS.

A thorough analysis and comparison of the fatty acid profiles of stipe and blade from Laminaria hyperborea, a kelp species found in the northern Atlantic, is presented. Lipids were extracted and fractionated into neutral lipids, free fatty acids and polar lipids, then derivatized to fatty acid methyl esters prior to GC-MS analysis. A total of 42 fatty acids were identified and quantified, including the n-3 fatty acids α-linolenic acid, stearidonic acid and eicosapentaenoic acid. An n-6/n-3 ratio of 0.8:1 was found in blade and 3.5:1 in stipe, respectively. The ratios vary between the lipid fractions within stipe and blade, with the lowest ratio in the polar lipid fraction of blade. The fatty acid amounts are higher in blade than in stipe, and the highest amounts of n-3 fatty acids are found within the neutral lipid fractions. The amounts of polyunsaturated fatty acids are 3.4 times higher in blade than stipe. This study highlights the compositional differences between the lipid fractions of stipe and blade from L. hyperborea. The amount of polyunsaturated fatty acids, compared to saturated- and monounsaturated fatty acids, as well as the n-6/n-3-ratio, is known to influence human health. In the pharmaceutical, food, and feed industries this can be of importance for production and sale of different health products. Additionally, lipids are today among the unused by products of alginate production, exploiting this material for commercial interest should give both economical and environmental benefits.

Culinary herbs and spices are widely used in daily diets. Pakistan flora is enriched with phytochemicals due to a diverse range of land. Phytochemicals, including volatile and non-volatile compounds, have captured much interest due to their numerous health advantages and significance in daily diet. The present study aimed to conduct in-depth metabolomic profiling of Pakistani-grown fenugreek leaves (Trigonella foenum-graecum), fennel seeds (Foeniculum vulgare), mint leaves (Mentha royleana), coriander seeds (Coriandrum sativum) and basil leaves (Ocimum basilicum) by using liquid chromatography–mass spectrometry (LC-MS/MS) and gas chromatography–mass spectrometry (GC-MS). The first study was conducted to optimize extraction using different solvents (methanol, ethanol, chloroform, acetone, and water). Total phenolic content (TPC), total flavonoid content (TFC), and total condensed tannins (TCT) were quantified along with the antioxidant and anti-diabetic activities. The highest TPC (125.42 ± 10.89 mg GAE/g) and the highest antioxidant and anti-diabetic potential were quantified in mint. Seventy-one phytochemical metabolites were identified using LC-MS/MS, while forty-nine volatile constituents were identified using the GC-MS. A positive correlation was identified between phenolic contents and their biological activities. Furthermore, molecular docking helped to find drug molecules with more excellent anti-diabetic activity based on their binding affinities. This study suggests that selected medicinal herbs from Pakistan have significant nutraceutical and phytopharmaceutical potential. This study could further help in drug discovery.

The cooking method is extremely important for the production of low-salt, wet-marinated, fermented golden pomfret because it strongly influences its flavor components and organoleptic quality. There are also significant differences in flavor preferences in different populations. The present study analyzed differences in the aroma characteristics of wet-marinated fermented golden pomfret after boiling, steaming, microwaving, air frying and baking using a combination of an electronic nose, GC-IMS and SPME-GC-MS. Electronic nose PCA showed that the flavors of the boiled (A), steam (B) and microwave (C) treatment groups were similar, and the flavors of baking (D) and air frying (E) were similar. A total of 72 flavor compounds were detected in the GC-IMS analysis, and comparative analysis of the cooked wet-marinated and fermented golden pomfret yielded a greater abundance of flavor compounds. SPME-GC-MS analysis detected 108 flavor compounds, and the results were similar to the baking and air frying. Twelve key flavor substances, including hexanal, isovaleraldehyde, and (E)-2-dodecenal, were identified by orthogonal partial least squares discriminant analysis (OPLS-DA) and VIP analysis. These results show that cooking method is a key factor in the flavor distribution of wet-marinated fermented golden pomfret, and consumers can choose the appropriate cooking method accordingly.

Aim: Nepal’s medicinal plants are culturally important and have diverse benefits. Senna alata belongs to the family Leguminosae and is a valuable plant utilized for medicinal and ornamental purposes. The aim of the research was to extract Senna alata leaves by successive maceration with various solvents. Methods: In this study, various methods were utilized to evaluate phytochemistry, overall phenolic and flavonoid content, in-vitro antioxidant, anti-inflammatory, cytotoxicity assay, anti-thrombolytic activity, and antibacterial activities. Results: The extractive values of Senna alata were determined as 1.58%, 0.78%, and 5.92% in hexane, ethyl acetate, and methanol, respectively. GC-MS analysis revealed major compounds such as 3-Methylmannoside, Neophytadiene, Campesterol, and Vitamin E in the leaf extract. Qualitative phytochemical screening verified the tannin content, carbohydrates, flavonoids, cardiac glycosides, glycosides, and saponins in the methanol extract. The total phenolic and flavonoid values were 46.36±4.5 mg GAE/gm and 480.4±3.055 QE/gm of dried extract, respectively. The extract exhibited significant antioxidant and anti-inflammatory activities, with IC50 values of 29.81 and 9.93, respectively. Furthermore, it demonstrated cytotoxic activity with an LC50 value of 767.85 in the brine shrimp bioassay. In terms of thrombolytic activity, the extract showed clot lysis percentages of 7.89% and 10.13% at concentrations of 10 mg/ml and 25 mg/ml, respectively. Conclusion: In conclusion, the methanolic extract of Senna alata leaves displayed therapeutic potential, including antioxidant, anti-inflammatory, cytotoxic, thrombolytic, and antibacterial effects. The existence of several chemicals via GC-MS analysis also verified plant's potential for therapeutic use.

In this study, a new approach to pesticide permeation through the apple peel into the pulp is discussed. The tested compounds can be classified, based on mode of action, as systemic (boscalid, cyprodinil, pirimicarb, propiconazole and tebuconazole) or contact (captan, cypermethrin and fludioxonil) pesticides. The barrier effect was assessed using a Franz flow-type vertical diffusion cell system. Residue analysis was performed using a modified quick, easy, cheap, efficient, rugged and safe (QuEChERS) extraction method coupled to gas chromatography with tandem mass spectrometry (GC-MS/MS). The limits of detection (LODs) ranged between 2.6 µg kg-1 (pirimicarb) and 17 µg kg-1 (captan), with the coefficient of variability (CV) lower than 6%, while recoveries ranged from 85% (boscalid) to 112% (captan) at 0.1 and 1 mg kg-1 spiked levels. The highest peel penetration was observed for pirimicarb, captan and cyprodinil, with cumulative permeation of 90, 19 and 17 µg cm-2, respectively. The total absorption was in the range from 0.32% (tebuconazole) to 32% (pirimicarb). Only cypermethrin was not quantitatively detected in the pulp and its use can be recommended in crop protection techniques. The obtained results indicate that molecular weight, octanol-water partition coefficient and water solubility are important parameters determining the process of pesticide absorption.

(E)-β-ocimene was the only found volatile chemical emitted by whole, live worker larvae of Apis mellifera L. by sampling in the vapor phase. While in addition to (E)-β-ocimene, there is evidence for the existence of other volatiles; but the changes of their composition and contents remain unknown during larval development, as are their differences from larvae to larval food. This is the main purpose of the study. We investigated volatile components of worker larvae and larval food using solid phase dynamic extraction (SPDE) coupled with gas chromatography-mass spectrometry (GC-MS). Nine compounds were identified with certainty and six tentatively, consisting of terpenoids, aldehydes, hydrocarbons, ester and ketone. The contents of volatiles of the second-instar worker larvae differ greatly from larvae of other stages mainly attributable to terpenoids, which made the second-instar worker larvae had significantly higher amounts of overall volatiles. Larval food contained significantly higher amounts of aldehydes and hydrocarbons than the corresponding larvae from the fourth to fifth-instar. We discovered volatiles in worker larvae and their food which were never reported before; we also mastered the change of these volatiles’ contents during larval development.

Fingerhuthia africana Lehm belongs to family Poaceae, is an erect perennial grass used traditionally to cure different diseases. The current study was carried out to find the bioactive compounds by GC-MS, elemental analysis through atomic absorption spectrophotometry, proximate analysis by AOAC, genotoxic activity through comet assay, antioxidant activity through DPPH and antidiarrheal activity through castor oil induce diarrhea followed by charcoal meal on mice model. GC-MS chromatogram represents different compounds detected in the crude extract. Major pharmacological bioactive compounds are 4H-Pyran-4-one, 2,3-dihydro-3,5-dihydroxy-6-methyl-; 4-Methyl itaconate; .alpha.-Terpineol; 1,2,3-Propanetriol, 1-acetate; Benzofuran, 2,3-dihydro-; Caryophyllene oxide; Hinesol; n-Hexadecanoic acid; 9,12-Octadecadienoic acid (Z,Z)-, methyl ester; Hexadecanoic acid and methyl ester. Elemental analysis of stem, leaves and roots of the plant show the presence of (macro and micro) nutrients such as Ca, Mg, K, Na, Cu, Pb, Zn, Mn, Fe, Cd and Co were absent in all parts. Proximate analysis of different parts revealed the presence of moisture contents (8.57%), ash (9.77%), fats contents (5.96%), fibers contents (45.03%), protein (3.62%), carbohydrates (39.71%) and Gross energy (Kcal/100g) (220.10). The ethanolic extract show dose-dependent genoprotective potential (127.38 ± 1.16), (83.28 ± 0.65), and (44.08 ± 1.40) at 50, 75, and 100 mg/100 ml, respectively, as compared to the methanolic extract which show genotoxic activity (85.13 ± 1.23) at high dose. After 90 minutes at a concentration of 300 (g/ml), methanolic extract demonstrated the greatest antioxidant potential (79.5%), followed by aqueous extract (76.5%). The methanolic extract of F. africana demonstrated antidiarrheal efficacy, with the maximum inhibition of charcoal movement (83.78%) occurring at a dosage of 300 mg/kg, followed by doses of 200 and 100 mg/kg, 73.26% and 59.56%, respectively. The current research highlights that the plant contains a substantial quantity of micro and macro nutrients, possesses high nutritional value, and exhibits pharmacological activities. These properties render the plant suitable for developing remedies to treat various therapeutic diseases.

Abstract: In this study the essential oils of Salvia officinalis growing in Sudan, were obtained by hydrodistillation and analyzed by Gas chromatography mass spectrometer, forty tow compounds were identified. The essential oil composition of S.officinalis found that it had many important compounds. The detected main compounds were oxygenated monoterpenes followed monohydrocarbone, squiterpenes and other compounds. The main essential oil constituents were α-terpineol (33.07%), camphor (11.57%), α-pinene (8.96%) camphene (5.09%) β-cymen (5.40 %) caryphyllene (3.76%) β-myrcene (3.65%) β-menth1-en-b-ol (3.45%) bomeol (3.38%) β-pinene (2.74%) Epiglobulol (2.59%) 1,8 Cineol (2.24%) and trans-β- terpinyl butanone(2.00% ).

Onions are known not only for their culinary importance but also for their nutritional and health-promoting properties. Both properties are closely linked to its content of organosulfur compounds, which account for up to 5% of the dry weight of an onion. Given the importance of these compounds, suitable analytical methods are required for their study. Two techniques should be highlighted in this context: gas chromatography coupled to mass spectrometry (GC-MS), and liquid chromatography coupled to mass spectrometry (LC-MS). In this study, eight different onion varieties were analyzed using two distinct analytical techniques: direct thermal desorption–gas chromatography-mass spectrometry (DTD-GC-MS) and high-resolution mass spectrometry (HRMS) on an LC-ESI-QqTOF instrument. Each method identified 18 different organosulfur compounds, with LC-HRMS targeting non-volatile compounds, such as cysteine sulfoxides, and GC-MS targeting volatiles, such as disulfides and trisulfides. The results obtained were studied using Pearson correlations and principal component analysis. No precise correlation was found between the initial organosulfur compounds in onions and their hydrolysates. Consequently, although GC is one of the most employed techniques in the scientific literature, the use of LC-HRMS or a combination of both techniques may offer a more comprehensive and accurate description of the metabolomic profile of onions.

Citrus species essential oils (EOs) are significant sources of bioactive compounds and demonstrate diverse therapeutic effects. However, limited documentation exists regarding the phytochemicals associated with their biological activities. This study aims to assess the antioxidant activity, plant inhibitory properties, and brine shrimp cytotoxic effects of EOs derived from three Citrus species: C. sinensis, C. limon, and C. hystrix. Utilizing chemometric analysis and gas chromatography-mass spectrometry (GC-MS) fingerprints, the volatile components contributing to antioxidant activity were elucidated. The peels of the Citrus samples were hydro-distillated to obtain EOs, and subsequently subjected to antioxidant, plant inhibitory, and brine shrimp cytotoxic assays. The results indicated that C. limon EO exhibited the highest antioxidant activity, while C. hystrix and C. sinensis EOs demonstrated pronounced inhibitory effects against Aetrmia salina and Lactuca sativa, respectively. GC-MS analysis facilitated the identification of key compounds in each EO. Principal component analysis (PCA) and hierarchy cluster analysis (HCA) effectively categorized Citrus EOs based on their antioxidant properties, highlighting the proximity of C. limon and C. sinensis. Among the identified compounds, D-limonene, α-Terpineol, Caryophyllene, (+)-3-Carene, β-Pinene, (-)-Spathulenol, trans-p-Mentha-1(7),8-dien-2-ol, and trans-Verbenol were the most discriminating compounds affected the antioxidant activity of C.limon and C. sinensis EOs.

Gas chromatography-coupled mass spectrometry (GC-MS) has been used in biomedical research to analyze volatile, non-polar, and polar metabolites in a wide array of sample types. Despite advances in technology, missing values are still common in metabolomics datasets and must be properly handled. We evaluated the performance of ten commonly used missing value imputation methods with metabolites analyzed on an HR GC-MS instrument. By introducing missing values into the complete (i.e., data without any missing values) NIST plasma dataset we demonstrate that Random Forest (RF), Glmnet Ridge Regression (GRR), and Bayesian Principal Component Analysis (BPCA) shared the lowest Root Mean Squared Error (RMSE) in technical replicate data. Further examination of these three methods in data from baboon plasma and liver samples demonstrated they all maintained high accuracy. Overall, our analysis suggests that any of the three imputation methods can be applied effectively to untargeted metabolomics datasets with high accuracy. However, it is important to note that imputation will alter the correlation structure of the dataset, and bias downstream regression coefficients and p-values.

Bacillus species produce different classes of antimicrobial and antioxidant substances: peptides or proteins with different structural composition and molecular mass and a broad range of volatile organic compounds (VOCs), some of which may serve as biomarkers for microorganism identification. The aim of this study is the identification of biologically active compounds synthesized by five Bacillus species using gas chromatography coupled to mass spectrometry (GC–MS). The current study profoundly enhances the knowledge of antibacterial and antioxidant metabolites ensuring the unambiguous identification of VOCs produced by some Bacillus species, which were isolated from vegetable samples of potato, carrot, and tomato. Phylogenetic and biochemical studies were used to identify the bacterial isolates after culturing. Phylogenetic analysis proved that five bacterial isolates BSS12, BSS13, BSS16, BSS21, and BSS25 showed 99% nucleotide sequence similarities with Bacillus safensis AS-08, Bacillus cereus WAB2133, and Bacillus acidiproducens NiuFun, Bacillus toyonesis FORT 102 and Bacillus thuringiensis F3, respectively. The crude extract was prepared from bacterial isolates to assess the antibiotic resistance potency and the antimicrobial potential against various targeted multidrug-resistant strains, including Candida albicans, Candida krusei, Enterococcus hirae, Escherichia coli, Klebsiella aerogenes, Klebsiella pneumoniae, Staphylococcus aureus, Staphylococcus epidermidis, Streptococcus group B, Streptococcus mutans, Shigella sonnei, Salmonella enteritidis, Serratia marcescens, Pseudomonas aeruginosa, and Proteus vulgaris. GC–MS analysis of bacterial strains found that VOCs from Bacillus species come in a variety of chemical forms, such as ketones, alcohols, terpenoids, alkenes, etc. Overall, 69 volatile organic compounds were identified from five Bacillus species, and all five were found to share different chemical classes of volatile organic components, which have a variety of pharmacological applications. However, 8 antibacterial compounds with different concentrations were commonly found in all five species: acetoin, acetic acid, butanoic acid, 2-methyl-, oxime-, methoxy-phenyl, phenol, 1,2-benzenedicarboxylic acid, bis(2-methylpropyl) ester, nonanoic acid, and hexadecanoic acid, methyl. The biology and physiology of Bacillus can be better understood using these results, which can also be used to create novel biotechnological procedures and applications. Moreover, because of its exceptional ability to synthesize and produce a variety of different antibacterial compounds, Bacillus species can serve as natural and universal carriers for antibiotic compounds in the form of probiotic cultures and strains to fight different pathogens, including mycobacteria.

Essential oils are mixtures of compounds obtained from plants, including flowers, roots, bark, leaves, seeds,peel, fruits, wood, that have risen up in the last decades thanks to their beneficial properties as antibacterial, antifungal and anti-inflammatory agents. The aim of this study was to characterize and analyze 13 different commercial essential oils with two different techniques. The first is GC-MS, coupled with SPME, thanks to which 204 different VOCs have been identified. The results show that a total of 95 compounds was found only in one oil, while the others were found with different frequencies in many of them. The most represented class is that of terpenes, as widely reported in literature. The second technique is based on an array of chemical gas sensors. This system was used to investigate whether sensors are able to identify these products. It turned out that basil, cinnamon and carnation are the most identifiable oils with different number and typology of sensors, especially tin oxide and copper oxide nanowires, while cayeput and thyme are more mistakable samples. Thanks to this detailed study, it has been possible to reach and obtain novel insights for the future development of this type of research.

The dynamics of surface and sub-surface water events can lead to slope instability resulting in anomalies such as slough slides on earthen levees. Early detection of these anomalies by a remote sensing approach could save time versus direct assessment. We have implemented a supervised Mahalanobis distance classification algorithm for the detection of slough slides on levees using complex polarimetric Synthetic Aperture Radar (polSAR) data. The classifier output was followed by a spatial majority filter post-processing step which improved the accuracy. The effectiveness of the algorithm is demonstrated using fully quad-polarimetric L-band Synthetic Aperture Radar (SAR) imagery from the NASA Jet Propulsion Laboratory’s (JPL’s) Uninhabited Aerial Vehicle Synthetic Aperture Radar (UAVSAR). The study area is a section of the lower Mississippi River valley in the southern USA. Slide detection accuracy of up to 98 percent was achieved, although the number of available slides examples was small.

The association between human and cat (F. catus) is well known. This domestic animal is also known for its malodorous urine and feces. The complexity of the odorous urine and feces impacts human life by triggering the human sensory organ in a negative way. The objective of this research was to identify the volatile organic chemicals (VOCs) and associated odors in cat urine and feces using gas chromatography-mass spectrometry and simultaneous sensory analysis of fresh and aged samples. The solid-phase microextraction (SPME) technique was used to pre-concentrate the VOCs emitted from urine or feces samples. Twenty-one compounds were identified as emitted from fresh urine, whereas 64 compounds were emitted from fresh feces. A contrasting temporal impact was observed on the emission of VOCs for urine and feces. On aging, the emission increased to 36 detected chemicals for stale urine, whereas only 17 chemicals were detected in stale feces. Not all compounds were malodorous; some compounds had a pleasant hedonic smell to the human nose. Although trimethylamine, low molecular weight organic acids, and ketones were contributors to the odor to some extent, phenolic compounds and aromatic heterocyclic organic N compounds generated the most intense odors and substantially contributed to the overall malodor, as observed by this study. This work might be useful to formulate cat urine and feces odor remediation approaches to reduce odor impacts.

Accurate determination of the concentration of alcohols and their metabolites is important in forensics and in several life science areas. A new method has been developed to quantify alcohols and their oxidative products using a headspace gas chromatography- mass spectrometer and isotope-labelled internal standards. This work demonstrates the application of this method, specifically in quantifying the concentration of oxidative products of alcohol and other minor alcohols found in hand sanitizers, which have become an essential household item since the COVID-19 pandemic. Apart from the major component, the minor alcohols found in hand sanitizers include methanol, isopropanol, and n-propanol. In ethanol-based hand sanitizers, a significant amount of acetaldehyde was observed as an oxidation product, while in isopropanol-based hand sanitizers, acetone was observed. The concentration of acetaldehyde in ethanol-based hand sanitizers significantly increased with storage time and temperature, whereas no such increase of acetone concentration was observed in isopropanol-based hand sanitizers with storage time and temperature.

Hang-ju was one of five officinal varieties of Flos chrysanthemum for its edible and potable usage. Besides Flos Chrysanthemum (FL), there were also Bud Chrysanthemum (BC) and Fetal Chrysanthemum (FC) at the early and late stage of buds, respectively, in the consumption market of Hang-ju with higher prices. Whether the quality and efficiency of BC and FC was superior to FL or merely consumption misunderstandings? Three commercial products of Hongxinju, a representive cultivar of Hang-ju were studied with a GC-MS based metabolomics approach, complemented with morphology, contents of moisture and protein and the anti-oxidant activity, to reveal the metabolic alterations of violate components in Hongxinju in different flowering stage and at different processing periods. It revealed that most of the violate components were increased from fresh FC to FL, and the low-boiling fractions, inflammatory methyl arachidonate and air-polluting component of ethylbenzene were declined while the representative components with pungent flavor and cool nature of a-curcumene and (Z,Z,Z)-9,12,15-octadecatrienoic acid, vision improving carotenol of rhodopin and high-boiling fractions were elevated after processed in final FL compared with that in BC and/or FC. Though the content of protein and anti-oxidative capacity of final BC and FC were nearly equal to those of FL, in comprehensive consideration of the representative components related with the efficiency in heat cooling and vision improving, as well as the representative components related with inflammation and air-pollution, final FL was recommended other than BC and FC in the practice of medicine with the yield and quality integrated into account.

Brain-Computer Interface (BCI) systems can assist physically challenged people to interact with their surroundings and improve the quality of their lives. Decoding human thoughts is a powerful technique that can assist paralyzed people who have lost their speech production ability. Speaking is a combined process involving synchronizing the brain and the oral articulators. This paper proposed a high-accuracy brain wave pattern recognition based on inner speech using a novel feature extraction method. Only eight EEG electrodes were used in this study, and they were set on selected spots on the scalp. Support Vector Machine (SVM) was employed to decode the recorded EEG dataset into four internally spoken words which are: Up, Down, Left, and Right. The proposed approach achieved overall classification accuracy that ranges between 96.20% to 97.5%. In addition, more performance evaluation metrics were estimated to test the reliability of classifying the EEG-based inner speech data, and we obtained 97.61%, 97.50%, and 97.73% for F1-score, recall, and precision respectively. Furthermore, the Area Under Curve of the Receiver Operating Characteristic (AUC-ROC) proved the strength of the proposed approach for classifying the specified inner speech commands by achieving a macro-average amount of 99.32%. The inner speech classification method using electroencephalography proposed in this work can clinically help improve communication for patients with problems including speech disorder, mutism, cognitive development, executive function, and psychopathology.

Currently, the pesticides are the global core concern because it is a boon to farmers against increasing disease-pest and simultaneously, pesticide residue is the major anxiety regarding human health. For that reason, identification and determination of factors affecting the application of pesticides are essential. To identify and evaluate determinants of pesticides application in Nepal, a household survey of 300 households was carried-out and an empirical analysis was done using multivariate probit model. Moreover, powder and liquid forms of pesticides were considered for summer and winter season in vegetable farming, which was assigned as outcome variables. Likewise, socio-economic, demographic, farm-level and perception data were considered as explanatory variables. Use of chemical fertilizers, age and gender of head of household, household size and access to weather information were found the most influencing factors. Moreover, forms of pesticides and growing seasons were found complementary to each other. Therefore, devising the policy options accordingly should balance needs of farmers and health of consumers.

This paper focuses on quantifying the economic and financial viability of NB-IoT and LoRaWAN technologies, two low-power wide-area network (LPWAN) technologies with unique characteristics that make them suitable for IoT applications. The purpose of the study is to propose an artefact for performing life cycle cost analysis and demonstrate its application to these technologies. The methodology uses pragmatic computational tools to facilitate the analysis and considers all relevant economic and financial factors, such as operating costs, equipment costs, and revenue potential. The main finding of the study is that NB-IoT and LoRaWAN technologies have different cost structures and revenue potentials, which may affect their economic and financial viability for different IoT applications. Ultimately, the study concludes that a comprehensive life cycle cost analysis is critical to making informed decisions about technology adoption, and that the proposed methodology can be applied to other IoT technologies to gain insight into their economic and financial viability.

The genus Beauveria include important entomopathogenic and endophytic fungi, among them, B. bassiana is the most studied species. However, there are few knowledge regarding their antimicrobial activity. The current research has been conducted to evaluate in vitro antibacterial efficacy of five isolates of B. bassiana against Bacillus cereus, B. megaterium, B. mojavensis, Clavibacter michiganensis (gram positive bacteria, G+ve), Xanthomonas campestris, X. vesicatoria, Escherichia coli, Pseudomonas aeruginosa and P. fluorescence (gram negative bacteria, G-ve). In addition, chemical composition of the principal diffusible metabolites and volatile organic compounds (VOCs) of the most efficient studied isolate of B. bassiana has been carried out using GC-MS analysis. The obtained results showed that, the isolate UniB2439-3 has promising antibacterial effect against most of studied target bacteria. GC-MS analysis of diffusible metabolites detected the presence of hexanedioic acid, bis(2-ethylhexyl) ester as the main compound in the cell-free culture filtrate. Furthermore, GC-MS analysis of VOCs revealed the presence of ethanol; butanal,2-methyl; 2,4-dimethyl-1-heptene; octane, 4-methyl and β-elemene as the main dominant bioactive compounds. The outgoing results explicated that, the isolates of B. bassiana have promising antibacterial activity which could be correlated to their diffusible and VOCs metabolites. Therefore, the selected isolate can be potentially used as a biocontrol agent against several bacteria especially G+ve ones. Taking in consideration that the antibiotics are forbidden in agriculture in many countries worldwide, search for possible natural alternatives as efficient antimicrobial agents are highly interesting.

This study aimed to determine the Gas Chrommatography (GC)-Mass Spectrometry (MS) profiles and insecticidal activity of essential oils (EOs) from Thymus vulgaris (Thyme) and Cymbopogon citratus (Lemongrass) against the invasive and devastating pest, Tuta absoluta (T. absoluta) through contact and fumigation routes. We found out that thyme oil was predominantly constituted of Thymol (22.16%), α-Pinene (15.35%) and p-Cymene (13.54%) whilst Neral (21.41%), Geranial (21.36%) and β-Myrcene (9.74%) were the major constituents of lemongrass oil. Lemongrass oil exhibited higher insecticidal efficiency irrespective of application mode with 50% lethal dose (LD50) values of 35.8 and 72.2 µL.L-1air on contact and fumigation routes, respectively. Lemongrass oil also lengthened pupal duration at all tested doses irrespective of application routes. The overall responses of Lemongrass oil surpassed that of the reference insecticide (Lynx®: Lambda-cyhalothrine; Acetamipride). Thus, the recorded data clearly showed the acute and long-term insecticidal effects of the studied EOs, though a greenhouse and open field trials are required prior to the validation of this approach as remediation measure for Integrated Pest Management (IPM) for tomato borer control in Cameroon and elsewhere.

Exoskeletons designed to assist patients with activities of daily living are becoming increasingly popular, but still are subject to research. In order to gather requirements for the design of such systems, long-term gait observation of the patients over the course of multiple days in an environment of daily living are required. In this paper a wearable all-in-one data acquisition system for collecting and storing biomechanical data in everyday life is proposed. The system is designed to be cost efficient and easy to use, using off-the-shelf components and a cloud server system for centralized data storage. The measurement accuracy of the system was verified, by measuring the angle of the human knee joint at walking speeds between 3 and 12 km/h in reference to an optical motion analysis system. The acquired data was uploaded to a cloud database via a smartphone application. Verification results showed that the proposed toolchain works as desired. The system reached an RMSE from 2.9° to 8°, which is below most of the comparable system. The system provides a powerful, scalable platform for collecting and processing biomechanical data, which can help to automize the generation of an extensive database for human kinematics.

The paper attempts to explore the relationship between federalism and rural development. Federalism is a division of power, responsibility and accountability to bring the administrative and political power closer to the ground and essentially to increase the good governance. On the other hand, rural development is a complex and multidimensional issue- especially much demanding for least developed and developing countries. A descriptive and qualitative approach was carried out to study the complex relationship between rural development and federalism. Similarly, a SWOT analysis was carried out to have a better understanding of the relationship. The study found that there is significant potentiality for accelerated development of rural landscape in federalism if carefully executed. However, on the other hand, federalism may pose several risks on rural development and may restrict the development pace if not executed with appropriate care and understanding. Therefore, the study concludes that cooperation and coordination among the federal structures are crucial for better development of the rural economy.

This study assessed farmers’ perception of climate change, estimated the determinants of, and evaluated the relationship among adaptation practices using the multivariate probit model. A survey in 300 agricultural households was carried out covering 10 sample districts considering five agro-ecological zones and a vulnerability index. Four adaptation choices (change in planting date, crop variety, crop type and investment in irrigation) were deemed as outcome variables and socioeconomic, demographic, institutional, farm-level and perceptions variables were deployed as explanatory variables. Their marginal effects were determined for three climatic variables—temperature, precipitation and drought. Age, gender and education of head of household, credit access, farm area, rain-fed farming and tenure, are found to be more influential compared to other factors. All four adaptation-options are found to be complimentary to each other. Importantly, the intensity of impact of dependent variables in different models, and for available adaptation-options, are found to be unequal. Therefore, policy options and support facilities should be devised according to climatic variables and adaptation options to achieve superior results.

This paper presents findings of a study on continuous feed-in management and continuous synthetic inertia contribution with wind turbines. A realistic case study, based on real measurements, is outlined. A wind turbine feeds into a weak feeder, such that its power has to be adapted to the permissible loading of this feeder. At the same time the wind turbine is to provide inertia to the grid by applying the previously published variable inertia constant controller. It is discussed that optimal grid utilisation and simultaneous inertia contribution are mandatory for the frequency control in power systems that are heavily penetrated with renewable energies. The study shows that continuous feed-in management can be combined well with continuous inertia provision. There are hardly any negative consequences for the wind turbine. The benefits for the grid are convincing, both in terms of increased system utilisation and in terms of provided inertia. It is concluded that wind turbines can enhance angular stability in a power system to a larger extent than conventional power plants.

Phenolic compounds, present in plants, provide substantial health advantages, such as antioxidant and anti-inflammatory properties, which enhance cardiovascular and cognitive well-being. Australia is enriched with a wide range of plants with phytopharmacological potential, which needs to be fully elucidated. In this context, we analyzed leaves of aniseed myrtle (Syzygium anisatum), lemon myrtle (Backhousia citriodora), and cinnamon myrtle (Backhousia myrtifolia) for their complex phytochemical profile and antioxidant potential. LC-ESI-QTOF-MS/MS was applied for screening and characterizing these Australian myrtles’ phenolic compounds and the structure-function relation of phenolic compounds. This study identified 145 and quantified/semi-quantified 27 phenolic compounds in these Australian myrtles. Furthermore, phenolic contents (total phenolic content (TPC), total condensed tannins (TCT), and total flavonoids (TFC)) and antioxidant potential of phenolic extracts from the leaves of Australian myrtles were quantified. Aniseed myrtle was quantified with the highest TPC (52.49 ± 3.55 mg GAE/g) and total antioxidant potential than other selected myrtles. Catechin, epicatechin, isovitexin, cinnamic acid, and quercetin were quantified as Australian myrtles' most abundant phenolic compounds. Moreover, chemometric analysis further validated the results. This study provides a new insight into the novel potent bioactive phenolic compounds from Australian myrtles that could be potentially useful for functional, nutraceutical, and therapeutic applications.

Living walls (LWs) are a climate change adaptation strategy for cities, as they have a cooling effect. Previous studies of the cooling effect of LWs were carried out in different climatic zones. These studies differed in their experimental design, or simulated data via models. Plants’ cooling capacity is explained by shading and transpiration, and depends on physical plant parameters, environmental factors, and system-related influences. A three-year-long trial was carried out between 2017 and 2019 at an experimental garden in Geisenheim, Germany. We chose a textile-based LW system with high water demand and plants from a wet/fresh habitat. We assumed that this would achieve high evaporative cooling. The experimental setup included four experimental walls which were exposed to the north, south, east, and west, respectively. The plant choice was divided into three plant mix variants (Cascade, Ground cover, and Meadow) and a Control with no vegetation. We measured the temperature with sensors and a thermal imaging (IR) camera in different setups. The main results were that the measured vegetation temperature (TV) depends on air temperature (TA), measurement position, plant mix variant, and plant species. We could detect the cooling effect only at a small distance from the LW (microclimatic). Our methodological approaches should be continued in further studies.

Selenium and iodine are essential micronutrients for humans. They are often deficient in food supply due to low phytoavailable concentrations in soil. Agronomic biofortification of food crops is one approach to overcome micronutrient malnutrition. This study focused on German consumers’ willingness to purchase selenium- and/or iodine-biofortified apples. For this purpose, an online survey was carried out. In this context, consumers were asked to choose their most preferred apple product from a set card of product alternatives (Discrete Choice Experiment). The multinomial logit model results demonstrated that German consumers’ have a preference in particular for iodine-biofortified apples. Furthermore, apple choice was mainly influenced by price, health claims, and plastic-free packaging material. Viewed individually, selenium did not exert an effect on product choice whereas positive interactions between both micronutrients exist.

Coptisine (Cop) exerts a neuroprotective effect in central nervous system disease, particularly ischemic stroke. However, its protective mechanism is still unclear. This study aimed to investigate the protective effect of Cop on cerebral ischemia-reperfusion (IR) rats with a middle cerebral artery occlusion model by integrating a gas chromatography-mass spectrometry (GC-MS) based metabolomics approach with biochemical assessment. Our results showed that Cop could improve neurobehavioral function and decrease the ischemia size in IR rats. In addition, Cop was found to decrease inflammatory mediators (e.g., prostaglandin D2 (PGD2) and tumor necrosis factor-α (TNF-α) and attenuate oxidative stress response (e.g., increase the superoxide dismutase (SOD) expression and decrease 8-iso-PGF2α level). Furthermore, GC-MS based cerebrospinal fluid (CSF) metabolomics analysis indicated that Cop influenced the level of glycine, 2,3,4-trihydroxybutyric acid, oleic acid, glycerol, and ribose during IR injury. Cop exhibited a good neuroprotective effect against cerebral IR injury and metabolic alterations which might be mediated through its antioxidant and anti-inflammatory property.

The quality of dietary patterns can be optimized using a mathematical technique known as linear programming (LP). LP methods have rarely been applied to individual meals. The present LP models optimized the breakfast meal for those participants in the nationally representative National Health and Nutrition Examination Survey 2011-2014 who ate breakfast (n=11,565). The Nutrient Rich Food Index (NRF9.3) was a measure of diet quality. Breakfasts in the bottom tertile of NRF9.3 scores (T1) were LP-modeled to meet nutrient requirements without deviating too much from current eating habits. Separate LP models were run for children and for adults. The LP-modeled breakfasts resembled the existing ones in the top tertile of NRF9.3 scores (T3), but were more nutrient-rich. Favoring fruit, cereals, and dairy, the LP-modeled breakfasts had less meat, added sugars and fats but more whole fruit and 100% juices, more whole grains, and more milk and yogurt. LP modeling methods can build on existing dietary patterns to construct food-based dietary guidelines and identify individual meals and/or snacks that need improvement.

Cesiumtrifluoroacetate (CsTFA) is a key chemical for RNA-based stable isotope analyses to link the structure and function of microbial communities. We report a protocol to easily synthesize CsTFA from Cesiumcarbonate (Cs₂CO₃₎ and Trifluoroacetate (TFA) and show that self-synthesized CsTFA behaves similar to commercial CsTFA in the separation of isotopically labelled and unlabelled E. coli RNA.

Diesel contamination of farming soils is of great concern because hydrocarbons are toxic to all forms of life and can potentially enter the food web through crops or plants used for remediation. Data on plant ability to uptake, translocate and accumulate diesel-derived compounds are controversial not only due to the probable diverse attitude of plant species but also because of the lack of a reliable method to distinguish petrogenic from biogenic compounds in plant tissues. The purpose of this study was to set up a GC-MS-based protocol enabling the determination of diesel-derived hydrocarbons in plants grown in contaminated soil for assessing human and ecological risks, predicting phytoremediation effectiveness and biomass disposal. To this aim two plant species Vicia sativa L. and Secale cereale L., belonging to two diverse vascular plant families, were used as plant models. They were grown in soil spiked with increasing concentrations of diesel fuel and the produced biomass was used to set up the hydrocarbon extraction and GC-MSD analysis. The developed protocol was also applied to the analysis of Typha latifolia L. plants, belonging to a different botanical family and grown in a long-time and highly contaminated natural soil. Results showed the possibility of distinguishing diesel-derived compounds from biogenic hydrocarbons in most terrestrial vascular plants, just considering the total diesel compounds in the n-alkanes carbon range C10-C26, where the interference of biogenic compounds is negligible. Diesel hydrocarbons quantification in plant tissues was strongly correlated (0.92<r2<0.99) to the concentration of diesel in spiked soils, suggesting a general ability of the considered plant species to adsorb and translocate relative low amounts of diesel hydrocarbons and the reliability of the developed protocol.

The limitations of investment casting of cobalt-based alloys are claimed to be less problematic with significant improvements in metal additive manufacturing by selective laser melting (SLM). Despite these advantages, the metallic devices are likely to display mechanical anisotropy in relation to build orientations, which could consequently affect their performance ‘in vivo’. In addition, there are inconclusive evidence concerning the requisite composition and post-processing steps (e.g. heat-treatment to relieve stress) that must be completed prior to the devices being used. In the current paper, we evaluate the microstructure of ternary cobalt-chromium-molybdenum (Co-Cr-Mo) and cobalt-chromium-tungsten (Co-Cr-W) alloys built with Direct Metal Printing and LaserCUSING SLM systems respectively at 0°, 30°, 60° and 90° inclinations (Φ) in as-built (AB) and heat-treated (HT) conditions. The study also examines the tensile properties (Young's modulus, E; yield strength, R_P0.2; elongation at failure, A_t and ultimate tensile strength, R_m), relative density (RD), and micro-hardness (HV5) and macro-hardness (HV20) as relevant physico-mechanical properties of the alloys. Data obtained indicate improved tensile properties and HV values after short and cost-effective heat-treatment cycle of Co-Cr-Mo alloy; however, the process did not homogenize the microstructure of the alloy. Annealing heat-treatment of Co-Cr-W led to significant isotropic characteristics with increased E and A_t (except for Φ = 90º) in contrast to decreased R_P0.2, R_m and HV values, compared to the AB form. Similarly, the interlaced weld-bead structures in AB Co-Cr-W were removed during heat-treatment, which led to a complete recrystallization in the microstructure. Both alloys exhibited defect-free microstructures with RD exceeding 99.5%.

High-temperature cooking process like frying, baking, smoking, or drying can induce chemical transformations in conventional food ingredients, causing deteriorative modifications. These reactions, including hydrolytic, oxidative, and thermal changes, are a common occurrence and can result in alterations to the food's chemical composition. In this study, a combination of sucrose and histidine (Su-Hi) was transformed through a process of charring or pyrolysis. The GC-MS profiling study showed that when sucrose and histidine (Su-Hi) are exposed to high temperatures (≈240°C), they produce carbonyl and aromatic compounds including beta-D-Glucopyranose, 1,6-anhydro (10.11 %), 2-Butanone, 4,4-dimethoxy- (12.89 %), 2(1H)-Quinolinone-hydrazine (5.73%), Benzenamine (6.35%), 2,5-Pyrrolidinedione, 1-[(3,4-dimethylbenzoyl)oxy]- (5.82%), Benzene-(1-ethyl-1-propenyl) (5.62%), and 4-Pyridinamine-2,6-dimethyl (5.52%). The compounds mentioned have the ability to permeate the cell membrane and contribute to the development of cell death by necrosis in human immune cells. The evidence available suggests that a specific set of pyrolytic compounds may pose a risk to immune cells. This investigation reveals the complex relationship between high-temperature cooking-induced transformations, compound permeation inside the cells, and downstream cellular responses, emphasizing the significance of considering the broader health implications of food chemical contaminants.

This study investigated the factors that influence consumer acceptance of fungus-resistant grape varieties (FRGV) in Germany. The qualitative research methodology involved conducting semi-structured interviews including sensory evaluation test with focus groups consisting of 48 consumers, and the data were evaluated using content analysis. The findings revealed that the attractiveness of a grape variety is determined by four distinct attributes. Furthermore, FRGV can be made more attractive to consumers by using denominations based on established grape varieties or by using and associating them with their sensory patterns. The sensory acceptance of FRGV varies significantly across consumer segments and vinification methods. Providing relevant information about the benefits of resistant grape varieties has a positive impact on consumer acceptance, and the level of interest and relevance varies by the target group. The study suggests that it is possible to enhance consumer acceptance by offering attractive grape varieties, targeting group-specific sensory profiles and engaging in storytelling campaigns that educate consumers about the advantages of resistant grapes.

Micro-pollutants such as 17β-Estradiol (E2) have been detected in different water resources and their negative effects on the environment and organisms have been observed. Aptamers are established as a possible detection tool, but the underlying ligand binding is largely unexplored. In this study, a previously described 35-mer E2-specific aptamer was used to analyse the binding characteristics between E2 and the aptamer with a MD simulation in an aqueous medium. Because there is no 3D structure information available for this aptamer, it was modeled using coarse-grained modeling method. The E2 ligand was positioned inside a potential binding area of the predicted aptamer structure, the complex was used for an 25 ns MD simulation, and the interactions were examined for each time step. We identified E2-specific bases within the interior loop of the aptamer and also demonstrated the influence of frequently underestimated water-mediated hydrogen bonds. The study contributes to the understanding of the behavior of ligands binding with aptamer structure in an aqueous solution. The developed workflow allows generating and examining further appealing ligand-aptamer complexes.

The plant Allium hookeri, belonging to the Allium genus, has a history of being used both as a common food ingredient and in herbal medicine. It has recently been reported to have anti-oxidant and anti-inflammatory effects. A. hookeri has been also shown to exhibit neuroprotective and anti-neuroinflammatory activities, but the active compounds responsible for these effects have not been identified in previous studies. This study aimed to perform a metabolite profiling using an HRESI-qTOF MS/MS-based molecular networking approach and identify the active compounds from A. hookeri that target senescent cell-associated secretory phenotype (SASP) inhibitory effects, which contribute to neuroprotective activities. As a result, ten compounds, including one new flavonoid (2) and nine known compounds (1 and 3–10), were identified, and their biological activity was tested. The most potent compound was N-trans-feruloyltyramine (7), which inhibited SASP markers and contributed to the senomorphic activities of A. hookeri. These findings suggest that the phenolamides from A. hookeri could be a promising source of bioactive compounds for preventing senescence-associated diseases.

Cassava (Manihot esculenta Crantz), domesticated in the Amazonian region of South America, presents an important diversity in Ecuador, where it is a main staple food; however, only few Ecuadorian cassava accessions have been included in international molecular assessments. The purpose of this study was to apply suitable cassava mi-crosatellites to characterize the genetic variability of the Ecuadorian cassava collection composed mainly of local landraces from the Coast, Andes and Amazonia regions. The use of microsatellite markers allowed the determination of the genetic diversity of the collection. Seven selected SSR primers, permitted to identify homozygous and hetero-zygous materials within the cassava collection of 133 accessions. The loci presented an average genetic diversity value of 0.7 and an average PIC value of 0.67, which is con-sidered high. Low number of duplicates (8.8%) were identified in the Ecuadorian col-lection which is not fully duplicated at CIAT. Currently, a wide range of cassava diver-sity is still cultivated in multi-crop agro-ecosystem, mainly in the Coast and Amazo-nian regions. Especially in the Amazonian region, due to important cultural uses of cassava by local ethnic communities, more in depth studies in the region could unveil the genetic diversity present in situ today.

This study assesses the secondary metabolites, minerals, antimicrobial, antioxidant, and anticancer properties of Micromeria fruticosa plant different botanical parts (leaf, stem, root, flower) extracted with various solvents. The plant samples were sequentially obtained using different solvents (n-hexane, ethanol and water) through steeping. Then, each of the extracts was further analyzed by using gas chromatography–mass spectrometry (GC-MS). Moreover, the extracts were bio-assayed to test their antioxidant, antibacterial, and anti-cancer activities. Quali-quantitative analysis of M. fruticosa crude extracts revealed the occurrence of 27 secondary metabolites were identified including mainly monoterpenes, sesquterpenes, and fatty acids, with varying quantities. Some of the major bioactive compounds included, Menthone (5.42-30.05%), Oleamide (3.40-32.20%), Pulegone (10.66-64.1%), and Menthol (3.61-100.0%), which were detected mostly in all plant parts with significant quantities. Several antioxidant minerals, mainly, Fe, Zn, and Mn, were detected with the highest amounts in the Micromeria water extracts. Results from antimicrobial assays showed that the water extract of leaves exhibited the highest DPPH scavenging activity (89.73%) followed by the water extract of flowers (80.07%) at a concentration of 100 μg/mL. The water extract of stems showed greater antimicrobial activity against all the tested gram negative and positive bacteria (Methicillin-resistant Staphylococcus aureus, Staphylococcus aureus, Escherichia coli, and Shigella sonnie). The leaves ethanolic and stem aqueous extracts had a strong antimicrobial activity against E. coli. and C. albicans. Flower aqueous extract demonstrated the highest cytostatic effect on the colon cell line by reducing viability up to 30.4%, followed by the leaf ethanol extract with 38.6% cell viability reduction at 1000 µg/mL. In conclusion, extraction solvents influenced the recovery of phytocompounds and the highest pharmacological activities of the different extracts could be correlated to the presence of additional bioactive compounds. Our results suggest that M. fruticosa plant is a promising source of natural products with antioxidant, anti-microbial and anti-cancer properties for potential nutraceutical, therapeutic, and functional food applications. , , , , , ,

Fructus Amomi (FA) is usually regarded as the dried ripe fruits of Amomum villosum Lour. (FAL) or Amomum villosum Lour. var. xanthioides T. L.Wu et Senjenis (FALX) However, FAL, which always has a much higher price because of its better quality, is confused with FALX in the market. As volatile oil is the main constituent of FA, a strategy of chromatography-mass spectrometry (GC-MS) and chemometric approches was applied to compare the chemical composition of FAL and FALX. The results showed that the oil yield of FAL was significantly higher than that of FALX. Total ion chromatograph (TIC) showed that cis-nerolidol existed only in FALX. Bornyl acetate and camphor, could be considered as the most important ones in FAL and FALX respectively. Moreover, hierarchical cluster analysis (HCA) and principal component analysis (PCA) successfully distinguished the chemical constitutes of the volatile oils in FAL and FALX. Additionally, bornyl acetate, α-cadinol, linalool, β-myrcene, camphor, d-limonene, terpinolene and endo-borneol were selected as the potential markers for discriminating FAL and FALX by partial least squares discrimination analysis (PLS-DA). In conclusion, this present study first developed a scientific approach to separate FAL and FALX based on volatile oils by GC-MS combined with chemometric techniques.

Parmigiano Reggiano cheese is one of the most appreciated and consumed food worldwide, especially in Italy, for its high content of nutrients and for its taste. However, these characteristics make this product subject to counterfeiting in different forms. In this study, a novel method based on an electronic nose has been developed in order to investigate the potentiality of this tool to distinguish rind percentage in grated Parmigiano Reggiano packages that should be lower than 18%. Different samples in terms of percentage, seasoning and rind working process were considered to tackle the problem at 360°. In parallel, GC-MS technique was used to give a name to the compounds that characterize Parmigiano and to relate them with sensors responses. Data analysis consisted of two stages: multivariate analysis (PLS) and classification made in a hierarchical way with PLS-DA ad ANNs. Results are promising in terms of correct classification of the samples. The classification rate is higher for ANNs than PLS-DA, reaching also 100% values.

(1) Background: Little is known about the baroque composer Domenico Scarlatti (1685-1757), whose life was centred behind closed doors at the royal court in Spain. There are no reports about his illnesses. From his compositions, mainly for harpsichord, an outstanding virtuosity can be read. (2) Case Presentation: In this case report, the only known oil painting of Domenico Scarlatti is presented, on which he is about 50 years old. In it one recognizes conspicuous hands with hints of watch glass nails and drumstick fingers. (3) Discussion: Whether Scarlatti had chronic hypoxia of peripheral body regions as a sign of, e.g., bronchial cancer or a severe heart disease, is not known. (4) Conclusions: The above-mentioned signs recorded in the oil painting, even if they were not interpretable at that time, are clearly represented and recorded for us and are open to diagnostic discussion from today's point of view.

Diabetes mellitus is the fifth deadliest disease in the developing countries. Even with all the research and new drugs available, combating diabetes is still challenging. There are successes in finding new cost effective drugs without side effects, even if not perfect. In our investigation we studied binding mechanism of secondary metabolite of T. chebula in silico. It was observed that three compounds out of 16 have a higher binding affinity for the target proteins. Ellagic acid showed highest binding affinity with alpha amylase, beta glucosidase and alpha glucosidase with lesser binding energies -4.5kcal/mol, -5.36kcal/mol and -4.48kcal/mol respectively. Arjungenin has lesser binding energy of 4.77 kcal/mol with glucokinase while luteoline has binding energy of -7.25kcal/mol for enzyme glycogen synthase kinase. These entire compounds interacted with non-covalent interaction. Petroleum ether extract showed the significant alpha amylase inhibitory activity i.e. 51.22% as compared to standard drug (65.99%).TLC analysis revealed the presence of total 9 compounds in different plant extracts one of them might be a lead compound which could be further exploited for the development of novel safer and potent antidiabetic drug.

This paper presents a comparison of two methods to represent variable blade inertia in two codes for aero-servo-elastic simulations of wind turbines: the nonlinear aeroelastic multi-body model HAWC2 and the nonlinear geometrically exact beam model BeamDyn for OpenFAST. The main goal is to enable these tools to simulate the dynamic behavior of a wind turbine with variable blade inertia. However, in order to simulate the structural response of wind turbines with variable blade inertias, the source code of load simulation tools need to be modified. This is due to the fact that, currently, state-of-the-art load simulation tools for wind turbines are unable to simulate variable rotor blade inertias. The validity of the modified codes is proven based on a simple beam model. The validation shows very good agreement between the modified codes of HAWC2, BeamDyn and an analytical calculation. The add-on of variable blade inertias is applied to reduce the mechanical loads of a 5 megawatt reference wind turbine with an integrated hydraulic-pneumatic flywheel in its rotor blades.

Metal nanoframes have gained tremendous attention in the domain of modern research and development due to their distinctive 3D spatial structure, efficient physiochemical properties, and comparatively good activity. Different strategies have been implicated by the researchers to design nano frame of varying chemical nature and shapes. Most of the synthetic protocols being adopted to design a nano framee, mainly consist of two main steps, nucleation and growth of solid particles and secondly excavation of the interiors. In this context, many synthetic methods are overviewed. To show their unprecedented performance or activity, a few applications in catalytic, biomedical, theranostic, SERS, sensing of different materials, reduction of CO2, etc are also discussed.

Natural dyes offer a bio-based opportunity to support attractive coloration to textile fabrics made from natural fibers like cotton, wool, hemp and many other materials. They can be part of a strategy to realize fully bio-based textile materials and clothing. Following this statement, the actual study investigates the use of wood extracts for dyeing of cotton fabrics. Actually extract powders of Logwood (Haematoxylon campechianum L.), Brazilwood (Caesalpinia spp.), and Quebracho wood (Schinopsis lorentzii) are used. The dyeing process is modified using different mordants based on iron and aluminum salts. These mordants are applied in pre-, meta- or post-mordant procedures. Color and fastness properties of prepared textile samples are determined by spectroscopic measurements, color measurements, washing procedures and Xenotest for measuring the light fastness. Finally, a broad range of different colorations can be realized by different combinations of wood extracts and mordanting procedures. A good wash fastness is reached for some color shades. For reaching good wash fastness, pre- and meta-mordanting procedures are more advantageous compared to post-mordanting. However, the light fastness of realized samples is only moderate to low. In conclusion, it can be stated that dyes from wood extracts are excellent materials to dye natural fibers if they are combined with the right mordanting agent in pre- or meta-mordanting procedures. The actual study is therefore a good proof-of-concept for the realization of fully bio-based colored textile materials.

A total of 473 metabolites were identified from 4 sour cherry genotypes using UPLC-TOF-MS. Untargeted metabolomics revealed the dominant chemical groups present in sour cherries. PCA showed that the diversity in sour-cherry metabolites was due to the genotype differences indicating iditol, malic acid, chlorobenzene, 2-mercaptobenzothiazole, and pyroglutamic acid as the predominant contributors. The variable importance in the projection (VIP &gt; 1.0) in partial least-squares–discriminant analysis described 20 biomarker metabolites, representing the cherry metabolome profiles. A heatmap of Pearson’s correlation analysis between the 20 biomarker metabolites and antioxidant activities identified seven antioxidant determinants that displayed the highest correlations with different types of antioxidant activities. This study of correlating metabolomics and antioxidant activities elucidated that the higher nutritional value and biological functions of select sour cherry genotypes can be useful for the development of nutraceutical and functional foods.

The 3GPP release 16 integrates TSN functionality into 5G and standardizes various options for TSN time synchronization over 5G such as transparent mode and bridge mode. The time domains for the TSN network and the 5G network are kept separate with an option to synchronize either of the networks to the other. The TSN time synchronization over 5G is possible either by using the IEEE 1588 generalized Precision Time Protocol (gPTP) based on UDP/IP multicast or via IEEE 802.1AS based on Ethernet PDUs. The INET and Simu5G simulation frameworks, which are both based on the OMNeT++ discrete event simulator, are widely used for simulating TSN and 5G networks. The INET framework comprises the 802.1AS based time synchronization mechanism and Simu5G provides the 5G user plane carrying IP PDUs. We modified the 802.1AS based synchronization model of INET so that it works over UDP/IP. With that it is possible to synchronize TSN slaves (connected to 5G UEs), across a 5G network, with a TSN master clock, present within a TSN network, that is connected to the 5G core network. Our simulation results show that 500 microseconds synchronization accuracy can be achieved with the corrected asymmetric propagation delay of uplink and downlink between the gNodeB (gNB) and the User Equipment (UE). Futhermore, the synchronization accuracy can be improved if the delay difference between uplink and downlink is known.

Plukenetia volubilis is an underutilized oilseed crop native to the Amazon basin, where it has been utilised by humans since Incan times. The large seeds contain approx. 45–50 % lipid, of which approx. 35.2–50.8 % is α-linolenic acid (C18:3 n-3, ω-3) and approx. 33.4–41.0 % is linoleic acid (C18:2 n-6, ω-6), the two essential fatty acids required by humans. The seeds also contain 22–30 % protein and have antioxidant properties. Due to its excellent nutritional composition and good agronomic properties, it has attracted increasing attention in recent years, and cultivation is expanding. When considering current global challenges, a reformation of our food systems is imperative in order to ensure food security, mitigation of climate change, and alleviation of malnutrition. For this purpose, underutilized crops may be essential tools, which can provide agricultural hardiness and reduced need for external inputs, climate resilience, diet diversification, and improved income opportunities for smallholders. Plukenetia volubilis is a promising up and coming crop in this regard and has considerable potential for further domestication; it has an exceptional oil composition, good sensory acceptability, is well suited for cultivation, and has numerous potential applications in, e.g. gastronomy, medicine, and cosmetics.

The commercial cultivation of microalgae began in the 1960s and Chlorella was one of the first target organisms. The species has long been considered a potential source of renewable energy, an alternative for phytoremediation, and more recently, as a growth and immune stimulant. However, Chlorella vulgaris, which is one of the most studied microalga, has never been comprehensively profiled chemically. In the present study, comprehensive profiling of the Chlorella vulgaris metabolome grown under normal culture conditions was carried out, employing tandem LC-MS/MS to profile the ethanolic extract and GC-MS for fatty acid analysis. The fatty acid profile of C. vulgaris was shown to be rich in omega-6, -7, -9, and -13 fatty acids, with omega-6 being the highest, representing more than sixty percent (>60%) of the total fatty acids. This is a clear indication that this species of Chlorella could serve as a good source of nutrition when incorporated in diets. The profile also showed that the main fatty acid composition was that of C₁₆-C₁₈ (>92%), suggesting that it might be a potential candidate for biodiesel production. LC-MS/MS analysis revealed carotenoid constituents comprising violaxanthin, neoxanthin, lutein, β-carotene, vulgaxanthin I, astaxanthin, and antheraxanthin, along with other pigments such as the chlorophylls. In addition to these, amino acids, vitamins, and simple sugars were also profiled, and through mass spectrometry-based molecular networking, 48 phospholipids were putatively identified.

For the purpose of improve the sustainability of products sold in the EU, Digital Product Passports is a mandatory solution. These passports would systematically gather information about products, such as detailing the materials involved to aid recycling and remanufacturing efforts, or recording the emissions produced throughout the manufacturing process. The overall goal is the establishment of a circular economy in the EU. Current research on Digital Product Passports is focused on collating content for sector-specific applications. However, achieving sustainability goals through Digital Product Passports will require new methods and technical solutions for digital collaboration between supply chain participants, especially in the manufacturing sector. Collaborative work on Digital Product Passports requires trust and traceability in data and access management to ensure privacy over the data contained. One way to enable this securely and confidentially is through the use of blockchain technology, in which stored data cannot be concealed, which is key to the traceability of digital product data documentation. This paper therefore presents a concept for the implementation of generically applicable cross-industry blockchain-based digital product passports. To this end, generic supply chain processes have been abstracted and condensed into the architecture of smart contracts. Great attention is paid to the establishment of traceability as well as privacy through the selection of the blockchain technology Secret Network in combination with Gaia-X functionalities. An illustrative use case for digital product passports in manufacturing is used to demonstrate the applicability of the presented concept. In this use case information about the digital nameplate and carbon footprint is exchanged securely and confidentially in a multi-tenant supply chain network based on the Industry 4.0 infomation model of the Asset Administration Shell.

The majority of the population in developing countries resides in the rural area. Development itself cannot address the challenges of the rural area since its economic, political and environmental landscape is different from an urban area. The paper attempts to assess the rural dimension aspect of Nepali Agriculture Policy since rural development and agricultural development is closely resembled due to an agrarian-based economy of the country and a large rural population. Therefore, a critical review of National Agriculture Policy, 2004 (NAP-2004) was carried out under “Commercialization of Agriculture”, “Food Security”, “Rural Infrastructure”, “Gender”, “Climate Change” and “Social Inclusion” thematic area. The results showed that NAP-2004 satisfactorily address rural development albeit ample space for improvement. The findings of the paper could be beneficial to policymakers and development workers in the field of rural development and agriculture along with academicians having interest in it.

Mangroves offer vital ecological advantages including air and water filtration, coastal and estuarine habitat provision, sediment stabilization, and wave energy absorption. Their intricate root systems play a key role in safeguarding shorelines from tsunamis and erosive storms by dissipating wave energy. Moreover, mangroves shield against boat wakes and wind-waves, bolstering shoreline defense. Wave dissipation is a function of forest width, tree diameter, and forest density. Restoration efforts of juvenile mangroves in Florida’s Indian River Lagoon (IRL) aim to reduce wave energy in areas vulnerable to erosion. Physical model testing of wave dissipation through mangroves is limited due to the complexity in representing the mangrove structure, where prop roots are non-uniform in both diameter and location. Previous studies have quantified wave dissipating effects through use of scaled and parameterized mangrove structures. This study measures the dissipation effects of live mangroves in a wave flume, forced by conditions representative of the IRL. These measurements are used to validate a parameterized dowel model. Error between wave attenuation factors for the live mangrove and dowel system was on average 2.5%. Validation of the modularized dowel system allowed for further parameterized testing to understand forest structure effects, such as sediment stabilization and wave attenuation.

In this study, a three-dimensional bioelectrochemical reactor system (3D-BERs) with granular activated carbon (GAC) epitomizes a novel treatment technology for treating nitrate-polluted water. The conventional denitrification process faces many challenges, including the huge demand for organic carbon, long-term accumulation of intermediate products, and the adaptation period. Results shown that under the optimal conditions of the COD/NO3--N ratio was 1.5, the denitrification efficiency reached 98.62%, when compared to 81.12% at COD/ NO3--N ratio of 3.5, and the initial pH of 7.5 ± 0.5, NO3--N was entirely removed at 2.2 h without accumulation of nitrite. The high initial ratio of NO2--N/NO3--N is mainly to accelerate the denitrification rate by accelerating the reduction of nitrite. Denitrification process followed by zero-order kinetics linear model for at different concentrations of inlet NO3--N, and achieved higher denitrification rate at greater inlet NO3--N concentration. High-throughput sequencing shows that the community structure and relative abundance of bacteria changed significantly, especially at the genes and the phyla level in immobilized GAC particles. Microbial composition enhanced the removal of nitrogen at the inner surface (IS) and bottom surface (BS) of immobilized GAC carriers. Therefore, this system is expected to be a more efficient and useful supplement or a cost-effective alternative compared to the traditional low carbon to nitrogen wastewater treatment system.

Raw material logistics reflects an important aspect of global trade. Raw materials form an essential basis for society, for daily life, and range from apples to zinc. This paper addresses the analysis and optimization of supply chains of raw materials in terms of their economic viability and their sustainability. Type representatives are chosen according to annual transported quantities. Hard coal represents bulk goods, aluminum primary raw materials with medium quantities, and rare earths primary raw materials with small quantities. Their respective supply chains are analyzed and subsequently possible strategies and methods and their application are discussed. The paper shows for the first time that the selection and application of optimization priorities (e.g. profitability or sustainability) depends on the primary raw material and its integration into global production chains.

Open Inertia Modelling (OpInMod) is a modelling framework designed to create unit commitment and economic inertia dispatch optimisation problems. Present energy system modelling generators do not consider power system inertia in unit commitment and economic dispatch modelling to assess future energy system pathways. However, maintaining sufficient power system inertia in power systems is the foundation for power frequency controllability. The work at hand describes the functionality and approaches of open source tool OpInMod. The softwares universal design approach increases reuse potential. OpInMod is distributed with a set of examples to test and understand OpInMod

This study aims to identify an optimal heat-treatment parameter set for an additively manufactured AlSi10Mg alloy in terms of increasing the hardness and eliminating the anisotropic microstructural characteristics of the alloy in as-built condition. Furthermore, the influence of these optimized parameters on the fatigue properties of the alloy investigated. In this respect, microstructural characteristics of an AlSi10Mg alloy manufactured by Laser-Based Powder Bed Fusion in non-heat-treated and heat-treated conditions were investigated. Their static and dynamic mechanical properties were evaluated, and fatigue behavior was explained by a detailed examination of fracture surfaces. Much of the microstructure in the non-heat-treated condition was composed of columnar grains oriented parallel to the build direction. Further analysis revealed a high fraction of pro-eutectic α-Al. Through heat-treatment, the alloy was successfully brought to its peak-hardened condition, while eliminating the anisotropic microstructural features. Yield strength and ductility increased simultaneously after heat-treatment, which is due to the relief of residual stresses, preservation of refined grains, and introduction of precipitation strengthening. The fatigue strength, calculated at 10^7 cycles, improved as well after heat-treatment and finally detailed fractography reviled that a more ductile fracture mechanism has happened in the heat-treated condition compared to the non-heat-treated condition.

The COVID-19 pandemic is one of the largest challenges in medicine and health care worldwide in recent decades, and it is infecting and killing increasing numbers of people every day. In this paper, we discuss the possible relationships among lysosomotropism, increasing lysosomal pH, and the SARS-CoV-2 infection and disease process, and we deduce a possible approach for treatment and prophylaxis. Lysosomotropism is a biological characteristic of small molecules, such as (hydroxyl)chloroquine, amitriptyline, NB 06, or sertraline, which is present in addition to intrinsic receptor-mediated or enzymatic pharmacological effects. Lysosomotropic compounds affect prominent inflammatory messengers, such as IL1B, CCL4, CCL20, and IL6, as well as cathepsin L dependent viral entry (fusion) into host cells. Therefore, this heterogeneous group of compounds is a promising candidate for the prevention and treatment of SARS-CoV-2 infections, as well as influenza A infections and cytokine release syndrome (CRS) triggered by bacterial or viral infections. Patients who have already taken medications with lysosomotropic compounds for other pre-existing conditions may benefit from this treatment in the COVID-19 pandemic. Increased lysosomal pH levels play an important role in the disease process in common skin disorders, such as psoriasis and atopic dermatitis, thus suggesting that affected individuals might benefit from their particular conditions in the COVID-19 pandemic. We suggest data analysis of patients with these diseases, and who are treated with lysosomotropic compounds, and, if the results are promising, subsequent clinical testing of off-label therapy with clinically approved lysosomotropic compounds in the current COVID-19 pandemic and future influenza A pandemics.

Turmeric, Curcuma longa L., is a type of medicinal plant characterized by its perennial nature and rhizomatous growth. It is a member of the Zingiberaceae family and is distributed across the world’s tropical and subtropical climates, especially in South Asia. Its rhizomes are highly valued for food supplements, spices, flavoring agents, and yellow dye in South Asia since ancient times. It exhibits a diverse array of therapeutic qualities that encompass its ability to combat diabetes, reduce inflammation, act as an antioxidant, exhibit anticancer properties, and promote anti-aging effects. In this study, organic extracts of C. longa rhizomes were subjected to HPLC separation followed by mass spectrometry analysis. The Global Natural Product Social Molecular Networking (GNPS) approach was utilized for the first time in this ethnobotanically important species to conduct an in-depth analysis of its metabolomes based on their fragments. A total of 30 metabolites including 16 diarylheptanoids, 1 diarylpentanoid, 3 bisabolocurcumin ethers, 4 sesquiterpenoids, 4 cinnamic acid derivatives, and 2 fatty acid derivatives were identified. Among 16 diarylheptanoids identified in this study, five of them are reported for the first time in this species.

Hepcidin-25 was identified as the main iron regulator in the human body by binding to the sole iron-exporter ferroportin. Studies showed that the N-terminus of hepcidin is responsible for this interaction, the same N-terminus that encompasses a small copper(II)-binding site known as ATCUN (amino terminal Cu(II)- and Ni(II)- binding) motif. Interestingly, this copper-binding property is largely ignored in most papers dealing with hepcidin-25. In this context, detailed investigations of the formed complex of hepcidin-25 with copper could reveal insights into its biological role. The present work is mainly focused on the study of the metal-bound form of hepcidin-25, which could be considered the biologically active form. The first part is devoted to the reversed-phase chromatographic separation of copper-bound and copper-free hepcidin-25, which was achieved by applying basic mobile phases containing 0.1% ammonia. Further, mass spectrometry (tandem mass spectrometry MS/MS, high resolution mass spectrometry HRMS) and nuclear magnetic resonance (NMR) spectroscopy were employed to characterize the copper-peptide. Lastly, a 3D model of hepcidin-25 with bound copper(II) is presented. The identification of metal complexes and potential isoforms and isomers, from which the latter usually are left undetected by mass spectrometry, led to the conclusion that complementary analytical methods are needed to characterize a peptide calibrant or reference material comprehensively. Quantitative nuclear magnetic resonance (qNMR), inductively-coupled plasma mass spectrometry (ICP-MS), ion-mobility spectrometry (IMS) and chiral amino acid analysis (AAA) should be considered among others.

It is the aim of this article to introduce a concise notation that is be able to capture the most important dimensions of sexuality and thus facilitate discussions. Moreover, the major three dimensions - sex, gender, and sexual orientation - lead to a straightforward classification which motivates the quest for stringent explanatory models, some of which are also discussed.

Abstract: The contribution of breakfast to diet quality (DQ) can inform future dietary guidelines. This study examined breakfasts that were associated with highest-quality diets. Dietary data came from the first reported day of the National Health and Examination Survey (NHANES) 2011-2014 (n=14,488). DQ measures were the Nutrient Rich Foods Index (NRF9.3) and the USDA Healthy Eating Index 2015 (HEI 2015). Analyses of breakfast intakes were conducted by NRF9.3 tertiles and by age and socioeconomic groups. Four out of 5 NHANES participants ate breakfast. Breakfast provided 19-22% of dietary energy depending on age. Breakfast intakes of complex carbohydrates and total sugars were higher and intakes of protein and fats were lower relative to energy intakes. Breakfast provided more that 20% of daily intakes of B vitamins, vitamins A and D, folate, calcium, iron, potassium and magnesium. Eating breakfast was associated with higher NRF9.3d scores. Breakfasts associated with top tertile of NRF9.3d had more carbohydrates and less added sugars and fats. Such breakfasts had more fruit and juices, more whole grains, more milk and yogurt and less meat and eggs. Breakfast patterns that favored fruit, whole grains, and dairy were associated with healthiest diets.

Sensory descriptive analysis was used to evaluate the aged Feng-flavored baijiu. The results indicated that there are notable differences in the samples of different ages. The samples with shorter storage times and fresh distilled Baijiu present bran flavor, and fresh green flavor. with the increase of storage time, the fragrance of honey, sweetness, flowers, and aging gradually increases. The samples of Feng-flavored baijiu were dected by Headspace solid-phase microextraction (HS-SPME) combined with comprehensive two-dimensional gas chromatography time-of-flight mass spectrometry (GC×GC–TOFMS) , in total, 496 sustances were identified in all samples, mainly containing 14 types of substances, such as esters, aldehydes etc., of which 42 substances were found in Feng-flavored baijiu for the first time. Chemometrics was used to analyze the key differential compounds. 143 differential compounds closely related to aging were preliminarily screened, and principal component analysis revealed that these samples were separated by year. 65 differential compounds were selected out by partial least squares discriminant analysis(PLS-DA). Furthermore, 43 key differential compounds were selected from the aged Feng-flavored baijiu combined with variable importance in projection and Pearson correlation coefficients. Partial least squares regression (PLSR) was used to research the correlation of sensory properties and key differential compounds, and the results indicated that most compounds were closely related to the aged Baijiu . This study afford theoretical basis and reference for flavor research of Feng-flavored baijiu.

The purpose of this study was to investigate the functional load capacity of the periodontal ligament (PDL) in a full arch maxilla and mandible model using numerical simulation. The goal of was to determine the functional load pattern in multi- and single rooted teeth with full and reduced periodontal support. CBCT data were used to create 3D-models of a maxilla and mandible. The DICOM dataset was used to create a CAD-model. For a precise description of the surfaces of each structure (enamel, dentin, cementum, pulp, PDL, gingiva, bone), each tooth was segmented separately, and the biomechanical characteristics were considered. A Finite-Element-Analysis (FEA) software computed the biomechanical behavior of stepwise increased force of 700N in cranial and 350N in ventral direction of the muscle approach of the Masseter muscle. The periodontal attachment (cementum-PDL-bone contact) was subsequently reduced in 1mm increments and the simulation repeated. Quantitative (pressure, tension, and deformation) and qualitative (color-coded images) data were recorded and descriptively analyzed. The teeth with the highest load capacities were the upper and lower molars (0.4-0.6MPa), followed by the premolars (0.4-0.5MPa) and canines (0.3-0.4MPa) when vertically loaded. Qualitative data showed that the area with the highest stress in the PDL were for single rooted teeth the cervical and apical area and for molars additionally the furcation roof. In both, single- and multi rooted teeth the gradual reduction of the bone levels caused an increase of the load on the remaining PDL. Cervical and apical areas as well as the furcation roof are the zones with the highest functional stress. The more bone loss, the higher the mechanical load on the residual periodontal supporting structures.

The paper is aimed to develop an improved acoustic-based Structural Health Monitoring (SHM) and Non-Destructive Evaluation (NDE) techniques, which provide the waves directivity emitting by the angle-beam wedge actuators in the thin-walled structures made of plastic materials and polymeric composites. Our investigation includes the dispersive analysis of the waves that can be excited in the studied plastic panel. Its results allowed to find two kinds of the generated acoustic waves - anti-symmetric Lamb waves A0 and shear horizontally polarized SH waves SS0. The bounds of the chosen frequency range for the experimental and numerical studies were accepted as a compromise between the desire to obtain high defects resolution by generating short waves, their adjustable directivity and maximum propagation length. The finite element model for the transducer was built by using the results of actuator structure experimental study. The frequency response functions for the actuator current and oscillation amplitude of the footprint surface demonstrated good agreement. The found eigenfrequencies of actuator's structure were used for the numerical and experimental study of the Lamb and SH wave generation and propagation in a thin-walled plastic panel. Our results convincingly demonstrated the satisfactory directivity of the actuated waves at their excitation on the frequencies that corresponded to the natural modes of the actuator oscillation. The authors assume that an efficient use of the proposed technique for other analyzed quasi-isotropic materials and applied actuators can be provided by a preliminary research using the similar approach and methods presented in this article.

(1) Background: Second Victims are health care workers negatively affected by adverse events and are prone to developing dysfunctional coping strategies compromising not only their own, but also patient safety. An effective way to address this issue is the implementation of peer support programs. This paper reports on the effectiveness of a peer support program at the Austrian Hietzing Clinic (KHI). (2) Methods: Telephone interviews were carried out after peer support sessions using a questionnaire. Descriptive analysis was carried out reporting frequencies and proportions for nominal variables, means with standard deviations for ordinal and interval-scaled variables. (3) Results: So far, 45 peer supporters have completed telephone interviews after a peer support session. The main reasons for the session were bad news from the private sphere and death of a patient. The peer supporters rated the helpfulness of the sessions for their colleagues as very high while not feeling very burdened themselves afterwards. (4) Conclusions: Underutilization of the program is probable. However, the high rating of helpfulness of the carried-out sessions by the peer supporters in combination with them not feeling very burdened, shows that the program is safe for the peer supporters and an upscaling is warranted.

Physical distancing and wearing a face mask are key interventions to prevent COVID-19. While this remains difficult to practice for millions of firefighters in fire engines responding to emergencies, the delayed forthcoming of evidence on the physical effectiveness of such safety interventions in this setting presents a major problem. In this field experimental study, we provided initial evidence to close this gap. We examined total aerosol burden in the cabin of a fire engine whilst manipulating crew size, natural ventilation, use of FFP2 respirators and use of SCBA full-face masks during 15-minute driving periods. At the same time, we controlled for crew activity and speaking, vehicle speed, cabin air temperature, pressure and humidity. Limiting the crew size, using FFP2 respirators and not donning SCBA full-face masks was associated with a reduction of the arithmetic mean of total aerosol burden of up to 49%. Natural ventilation as tested in this study was associated with both an increase and a decrease of total aerosol burden. This study provided initial evidence on the physical effectiveness of safety interventions in fire engines to reduce potential airborne transmission of SARS-CoV-2 through aerosols. More research about the physical and clinical effectiveness of such safety interventions is needed.

Myocardial involvement among critical patients with coronavirus disease 2019 (COVID-19) has a worse outcome. The occurrence of an imbalance in oxygen supply results in the release of pro-inflammatory cytokines which leads to increased ventilation support requirement and increase risk of mortality. Our aim was to evaluate the association between hs-Troponin I level and global longitudinal strain as evidence of myocardial involvement among critical COVID-19 patients. Methods. We performed prospective cohort study from February 1st – July 31st, 2021 at Dr. Soetomo General Hospital, Surabaya as referral center for COVID-19 care. Of the 65 critical COVID-19 included, 41 (63.1%) were men, with a median (interquartile range) age of 51.0 years (20.0-75.0).Subjects were recruited according to WHO criteria for severe COVID-19 and CDC criteria for myocarditis. All subjects recruited were examined using echocardiography to measure global longitudinal strain (GLS) and blood samples were taken to measure hs-Troponin. Subjects were then followed to assess their needs for mechanical ventilation and in-hospital mortality. Severe COVID-19 subjects with cardiac injury were associated with an increased need for intubation (78.5%) and an increased incidence of myocarditis (50.8%). There was an association between the use of intubation and the risk of mortality in patients (66.7% vs. 33.3%, p-value &lt;0.001). Both reduced GLS and increased hs-troponin are associated with increased myocarditis (p-value &lt;0.001 and 0.004 respectively). Reduced GLS is associated with higher mechanical ventilation needs (12.17 + 4.79 vs.15.65 + 4.90, p-value 0.02) and a higher mortality rate (11.36 + 4.64 vs. 14.74 + 4.82; p-value 0.005). Increased hs-troponin is associated with higher mechanical ventilation needs (25.33% vs. 3.56%, p-value 0.002) and a higher mortality rate (34.57% vs. 5.76%, p-value 0.002). Compared with contemporary controls, critical COVID-19 patients with myocardial involvement and elevated cardiac troponin level are associated with higher mechanical ventilation needs and a higher mortality rate.

This research aims to elucidate the organizational patterns of interregional economic interdependence to enhance our comprehension of the national economy's structure at a regional scale. Employing a multilayer network model, this study represents economic interdependence among Indonesian regions, utilizing the InterRegional Input-Output (IRIO) table. Through the application of various metrics, such as degree and strength distribution, assortativity coefficient, and global and local rich club coefficient, to the multilayer IRIO network, we uncover the organizational patterns of economic exchanges between provinces and economic sectors within Indonesia. Our findings demonstrate that a multilayer network approach reveals the heterogeneous and complex structure of the national economy at the regional level. By analyzing the assortativity pattern and global rich-club coefficient, we illustrate that the IRIO network exhibits a hierarchical organization, where significant provincial-sector nodes are interconnected and form dense rich clubs, extending from a few structural cores to peripheral regions. Additionally, we identify distinct connectivity patterns of non-rich nodes based on their incoming and outgoing relations. The insights gained from this study have implications for the macro-control of regional development.

The present study aims at deposition of zinc phosphate coatings with the incorporation of nano Titanium dioxide particles by chemical phosphating method. Zinc phosphate coatings were developed on low carbon steel by using nano TiO2 in the standard phosphating bath. The Coated low carbon steel samples were assessed for corrosion studies using electrochemical impedance spectroscopy and potentiodynamic polarisation techniques in 3.5% NaCl solution. Chemical composition of the coatings was analysed by energy dispersive X-ray spectroscopy (EDX). Significant variations in the coating weight, porosity and corrosion resistance were observed with the addition of nano TiO2 in the phosphating bath. Corrosion rate of nano TiO2 incorporated chemical phosphate coated samples was found to be 3.5 mpy which was 4 times less than the bare uncoated low carbon steel (~14 mpy). Electrochemical impedance spectroscopy studies revels in the reduction of porosity in nano TiO2 phosphate coated samples. It was found that nano TiO2 particles in the phosphating solution yielded phosphate coatings of higher coating weight, greater surface coverage and enhanced corrosion resistance than the normal zinc phosphate coatings (developed using normal phosphating bath).

Re-investigation of the chemical composition of the annual plant Mitracarpus scaber Zucc. led to the identification of clarinoside, a new pentalogin derivative containing a rare quinovose moiety, and the known compound harounoside. While the planar structure was fully determined using tandem MS and quantum mechanics calculations (QM), the tridimensional structure was unravelled after isolation and NMR analysis. The absolute configuration was assigned by comparison of experimental and theoretical SRCD spectra. Both compounds were tested for anti-inflammatory activity and compound 1 showed the ability to inhibit the production of interleukin-8 (Il-8) with an IC₅₀ of 9.17 µM.

University-Business partnership for collaborative curriculum design, development and delivery is possibly the less explored dimension of University Business Collaboration (UBC). Even if some models for curricular design and development might be available, scarce information exists on how the partnership is constructed, the new curricula are designed, developed and how they are implemented. This article intends to present and discuss the experience obtained during a three-year European funded Project, namely Think4Jobs. This project exemplifies the significance and benefits of UBC in the design, development and delivery of curricula that meet the evolving demands of the labour market while promoting Critical Thinking (CT) as a foundational 21st century skill to contribute to graduates' employability. Think4Jobs project brought together a multidisciplinary team of researchers and business organisations from five European countries (Germany, Greece, Lithuania, Portugal and Romania) with interests in promoting and developing CT and mitigating eventual competence gaps. The project's success was attributed to key practices, including defining a common conceptualization of CT, employing participatory co-design, and providing common training for university and business partners. Clear objectives, explicit roles, effective communication, and ongoing evaluation further enhanced the collaboration. Experiential learning, real-work problems, and case studies reinforced the curricula, bridging the gap between academia and the labour market. By embracing these insights, future UBC initiatives can empower graduates with the necessary skills to stand out in an ever-changing labour market, contributing to enhanced education and successful careers.

Alterations in the carnitine shuttle system may be an indication of the presence of cancer. As such, in-depth analyses of this pathway in different malignant tumors could be important for the detec-tion and treatment of this disease. The current study aims to assess the profiles of carnitine and acylcarnitines in gliomas with respect to their grade, the presence of isocitrate dehydrogenase (IDH) mutations, and 1p/19q co-deletion. Brain tumors obtained from 19 patients were sampled on-site using solid-phase microextraction (SPME) immediately following excision. Analytes were desorbed and then analyzed via liquid chromatography-high resolution mass spectrometry. The results showed that SPME enabled the extraction of carnitine and 22 acylcarnitines. An analysis of the correlation factor revealed presence of two separate clusters: short-chain and long chain car-nitine esters. Slightly higher carnitine and acylcarnitine concentrations were observed in the higher malignancy tumor samples (high vs low grade), and in those samples with worse projected clinical outcomes (without vs with IDH mutation; without vs with 1p/19q co-deletion). Thus, the proposed chemical biopsy approach offers a simple solution for on-site sampling that enables sample preservation, thus supporting comprehensive multi-method analyses.

We describe the development and validation of a HPLC-MS/MS method to assess the pharmacokinetics and tumour distribution of fenretinide, a synthetic retinoid chemically related to all-trans-retinoic acid, after administration of a novel oral nanoformulation of fenretinide, called bionanofenretinide (BNF). BNF was developed to overcome the major limitation of fenretinide: its poor aqueous solubility and bioavailability due to its hydrophobic nature. The method proved to be reproducible, precise, and highly accurate for the measurement of the drug and the mains metabolites. The lower limit of quantification resulted 1 ng/mL. The curve range of 1-500 ng/mL and 50-2000 ng/mL, for plasma and tumor homogenate respectively, was appropriate for the analysis, as demonstrated by the accuracy between 96.8% and 102.4% for plasma and 96.6-102.3% for tumor. The inter-days precision and accuracy determined on quality controls at 3 different levels were in ranges of 6.9%-7.5% and 99.3-101.0% and 0.96-1.91% and 102.3-105.8% for plasma and tumour, respectively.

Hydrogen sulfide (H2S) is an environmental toxicant of health concern. The brain is a major target in acute H2S poisoning. This study was to test the hypothesis that acute and subchronic ambient H2S exposures alter the brain metabolome. Male 7-8 week-old C57BL/6J mice were exposed by whole-body inhalation to 1000 ppm H2S for 45 min and euthanized at 5 min or 72 h for acute exposure. For subchronic study, mice were exposed to 5 ppm H2S 2 h/day, 5 days/week for 5 weeks. The brainstem was removed for metabolomic analysis. Enrichment analysis showed the metabolomic profiles in acute and subchronic H2S exposures matched with those of cerebral spinal fluid from patients with seizures or Alzheimer’s disease. Acute H2S exposure decreased excitatory neurotransmitters, aspartate and glutamate, while the inhibitory neurotransmitter, serotonin, was increased, which may explain H2S-induced loss of consciousness. Branched-chain amino acids and glucose were increased by acute H2S exposure. Subchronic H2S exposure within OSHA guideline surprisingly decreased serotonin altering central nervous system. In subchronic H2S exposure, glucose was decreased while polyunsaturated fatty acids, inosine, and hypoxanthine were increased. Collectively, these results provide important mechanistic clues of acute and subchronic ambient H2S poisonings and show that H2S alters brainstem metabolome.

Plaque psoriasis is a common, long-lasting illness that affects the immune system and causes significant negative impacts on a patient's physical health, well-being, and ability to work effectively. Deucravacitinib (DEU) is the first oral medication used in the treatment of plaque psoriasis, a chronic skin condition that causes red, scaly patches on the skin. DEU is a type of medication called an oral Janus kinase (JAK) inhibitor, which works by blocking specific enzymes that play a role in the inflammation and immune response associated with psoriasis. Therefore, a quick, easy, novel, reliable, sensitive, and straightforward Liquid Chromatography-Tandem Mass Spectrometry (LC-MS/MS) approach was used to analyse DEU in plasma samples. The LC-MS/MS method for the determination of DEU in human plasma was based on using trimethoprim as an internal standard (IS). The separation of DEU and IS was carried out via liquid-liquid extraction (LLE). The isolated substances were then subjected to the chromatographic system using the ACE-C18 column (4.6x100 mm, 5 µm). The mobile phase employed consisted of methanol and a solution of 2 mM ammonium formate (80:20 v/v, respectively). The flow rate used was set at 0.9 mL min-1. The creative strategy was performed by running an ABSCIEX API 4000 mass spectrometer with an electron spray ionization source in Multiple Reaction Monitoring (MRM) modes. The ion transitions m/z 426.3  358.2 was used for DEU quantitation, while the ion transitions m/z 291.1  261.1 was used for trimethoprim quantitation. The accuracy, precision, linearity, recovery, and selectivity of DEU were deemed acceptable when validated for a concentration range between 0.500 to 601.050 ng/mL, utilizing a weighting factor of 1/x2.

Heterocytous cyanobacteria are among the most prolific source of bioactive secondary metabolites, including anabaenopeptins (APTs). A terrestrial filamentous Brasilonema sp. CT11 collected in Costa Rica bamboo forest, as black mat was studied using a multidisciplinary approach: genome mining and HPLC-HRMS/MS coupled with bionformatic analyses. Herein, we report the nearly complete genome consisting 8.79 Mbp with a GC content of 42.4%. Moreover, we report on three novel tryptophane-containing APTs; anabaenopeptin 788 (1), anabaenopeptin 802 (2) and anabaenopeptin 816 (3). Further, the structure of two homologues, i.e., anabaenopeptin 802 (2a) and anabaenopeptin 802 (2b) was determined by spectroscopic analysis (NMR and MS). Both compounds were shown to exert weak to moderate antiproliferative activity against HeLa cell lines. This study also provides the unique and diverse potential of biosynthetic gene clusters and an assessment of the predicted chemical space yet to be discovered from this genus.

Glioblastoma (GBM) presents a significant public health challenge as the deadliest and most common malignant brain tumor in adults. Despite standard-of-care treatment, which includes surgery, radiation, and chemotherapy, mortality rates are high, underscoring the critical need for advancing GBM therapy. Over the past two decades, numerous clinical trials have been performed, yet only a small fraction demonstrated benefit, raising concerns about the predictability of current preclinical models. Traditionally, preclinical studies utilize treatment-naïve tumors, failing to model the clinical scenario where patients undergo standard-of-care treatment prior to recurrence. Recurrent GBM generally exhibits distinct molecular alterations influenced by treatment selection pressures. In this review, we discuss the impact of treatment - surgery, radiation, and chemotherapy - on GBM. We also provide a summary of treatments used in preclinical models, advocating for their integration to enhance the translation of novel strategies to improve therapeutic outcomes in GBM.

The thorough description of the peculiarities of additively manufactured structures represents a current challenge for aspiring freeform fabrication methods, such as the selective laser melting (SLM). All of which have an immense advantage in the fast fabrication (no special tooling or moulds required), the geometrical flexibility in the design of components, and their efficiency when only low quantities are required. However, designs demand the precise knowledge of the material properties, which in case of additively manufactured structures are anisotropic and, under certain circumstances, in addition of an inhomogeneous nature. Furthermore, these characteristics are highly dependent on the fabrication settings. Within this study, the anisotropic tensile properties of selective laser melted stainless steel (1.4404, 316L) are investigated: The Young’s modulus ranged from 148 GPa to 227 GPa, the ultimate tensile strength from 512 MPa to 699 MPa and the breaking elongation ranged, respectively, from 12% to 43%. The results were compared to related studies, in order to classify the influence of the fabrication settings. Furthermore, the influence of the chosen raw material was addressed by comparing deviations on the directional dependencies reasoned by differing microstructural developments during manufacture. Stainless steel was found to possess its maximum strength at a 45° layer versus loading offset, which is precisely where AlSi10Mg was previously reported to be at its weakest.

The epithelial-mesenchymal transition (EMT) is a major event in idiopathic pulmonary fibrosis pathogenesis. Here, we investigated whether growth arrest-specific protein 6 (Gas6) plays a protective role in lung fibrosis via suppression of the EMT and fibroblast activation. rGas6 ad-ministration inhibited the EMT in isolated mouse ATII cells 14 days post-BLM treatment based on morphologic cellular alterations, changes in mRNA and protein expression profiles of EMT markers, and induction of EMT-activating transcription factors. BLM-induced increases in gene expression of fibroblast activation-related markers and the invasive capacity of primary lung fi-broblasts in primary lung fibroblasts were reversed by rGas6 administration. Furthermore, the hydroxyproline content and collagen accumulation in interstitial areas with damaged alveolar structures in lung tissue were reduced by rGas6 administration. Targeting Gas6/Axl signaling events with specific inhibitors of Axl (BGB324), COX-2 (NS-398), EP1/EP2 receptor (AH-6809), or PGD2 DP2 receptor (BAY-u3405) reversed the inhibitory effects of rGas6 on EMT and fibroblast activation. Finally, we confirmed the antifibrotic effects of Gas6 using Gas6−/− mice. Therefore, Gas6/Axl signaling events play a potential role in inhibition of EMT process and fibroblast acti-vation via COX-2-derived PGE2 and PGD2 production, ultimately preventing the development of pulmonary fibrosis.

In 2012 the Open Geospatial Consortium published GeoSPARQL defining “an RDF/OWL ontology for [spatial] information”, “SPARQL extension functions” for performing spatial operations on RDF data and “RIF rules” defining entailments to be drawn from graph pattern matching. In the 8+ years since its publication, GeoSPARQL has become the most important spatial Semantic Web standard, as judged by references to it in other Semantic Web standards and its wide use for Semantic Web data. An update to GeoSPARQL was proposed in 2019 to deliver a version 1.1 with a charter to: handle outstanding change requests and source new ones from the user community and to “better present” the standard, that is to better link all the standard’s parts and better document &amp; exemplify elements. Expected updates included new geometry representations, alignments to other ontologies, handling of new spatial referencing systems, and new artifact presentation. In this paper, we describe motivating change requests and actual resultant updates in the candidate version 1.1 of the standard alongside reference implementations and usage examples. We also describe the theory behind particular updates, initial implementations of many parts of the standard, and our expectations for GeoSPARQL 1.1’s use.

The important sampling parameters of a headspace solid phase microextraction-gas chromatography-mass spectrometry (HS-SPME-GC-MS) procedure, extraction temperature, extraction time and sample volume were optimized to quantify 23 important impact odorants in reduced alcohol red and white wines. A three-factor design of Box-Behnken experiments was used to determine optimized sampling conditions for each analyte, and a global optimized condition at every ethanol concentration of interest determined using a desirability function that accounts for a low signal response for compounds. Shiraz and Chardonnay wines were dealcoholized from 13.7 and 12.2% v/v ethanol respectively, to 8 and 5% v/v, using a commercially available membrane-based technology. A sample set of the reduced alcohol wines were also reconstituted to their natural ethanol level to evaluate the effect of ethanol content reduction on volatile composition. The three-factor Box-Behnken experiment ensured an accurate determination of the headspace concentration of each compound at each ethanol concentration, allowing comparisons between wines at varying ethanol levels to be made. Overall, the results showed that the main effect of extraction temperature was considered the most critical factor when studying the equilibrium of reduced alcohol wine impact odorants. The impact of ethanol reduction upon the concentration of volatile compounds clearly resulted in losses of impact odorants from the wines. The concentration of most analytes decreased with dealcoholization compared to that of the natural samples. Significant differences were also found between the reconstituted volatile composition and 5% v/v reduced alcohol wines, revealing that the dealcoholization effect is the result of a combination between the type of dealcoholization treatment and reduction in wine ethanol content.

Sphingosine 1-phosphate (S1P) is a signaling lipid molecule involved in various cellular processes. It is important to develop a quantitative method for S1P to determine endogenous levels and to investigate its functions. Especially since S1P is a tiny lipid component of most biological samples, highly sensitive analysis by LC-MS/MS is required. The main challenge in S1P analysis by chromatography is peak broadening due to the presence of a polar phosphate and zwitterion formation in S1P. In this study, we used hydrogen fluoride (HF) to efficiently remove a phosphate and then analyzed the surrogate, sphingosine, as a sharp peak by LC-ESI-MS/MS. We optimized the dephosphorylation reaction in terms of reaction time, temperature, and HF concentration. Multiple reaction monitoring (MRM) for dephosphorylated form of S1P and C17-S1P as internal standard at m/z transition 300.4&gt;282.4 (quantification ion), 300.4&gt;262.4 (qualification ion), 286.3&gt;268.2 (internal standard). This method was validated by essential parameters such as specificity, linearity, range, LOQ, LOD, accuracy, precision, and repeatability. To confirm this new method, we quantified S1P levels in various serum products (100.02 ~ 284.38 nM). To apply the method in vivo, we analyzed S1P in plasma and kidney tissues obtained from a chronic kidney disease (CKD) mouse model. S1P levels were increased only in CKD kidney tissue but not in plasma. In conclusion, by applying the dephosphorylation step with HF, we established a new sensitive LC-MS/MS quantitative method for S1P that can be applied to biological samples.

Among the many neglected underutilized species, tuberous Andean root crops like the ahipas (Pachyrhizus ahipa) constitute a promising alternative for increasing diversity in nutrient sources and food security at a regional level. In this study, we present the content of some functional compounds in tuberous roots from several ahipa accessions and the progenies of the interspecific hybrid X207 (P. ahipa × P. tuberosus). A significant objective was to determine protein and free amino acids in the roots to evaluate their food quality as protein supply. The interspecific hybrids have been found to possess the root quality to provide the crop with a higher dry matter content. The high dry matter content of the P. tuberosus Chuin materials is retained in the root quality of the hybrids. Food functional components like carbohydrates, organic acids, and proteins were determined in several ahipa accessions and a stable (non-segregating) progeny of the interspecific hybrid, X207. The X207 roots showed a significantly higher dry matter content and a lower content in soluble sugars, but no significant differences were found in starch content or organic acids compared to the ahipa accessions. About the root mineral contents, Fe and Mn concentrations in X207 were significantly raised compared to the average of ahipa accessions. Among the ahipa and the hybrid, no prominent differences in protein content or protein amino acids were found, being both partially defective in providing sufficient daily intake of some essential amino acids. Root weight, a central component of root yield, was significantly higher in X207, but thorough field studies are required to substantiate the hybrid’s superior yield performance..

Emerging pollutants as pharmaceuticals have been focusing international attention for few decades. Ciprofloxacin (CIP) is a common drug widely found in effluents from hospitals, industrial and different wastewater treatment plants, as well as rivers. In this work, the lab-scale 3D-BER system was established, and more than 90% of the antibiotic CIP removal from the Low C/N wastewater. Best results were obtained with current intensity, and different C/N ratio significantly improve the removal of CIP and nitrates, when the ideal conditions were; C/N = 1.5-3.5, pH =7.0-7.5, and I = 60 mA. The highest removal efficiency of CIP = 94.20 %, NO3--N= 95.53 % and total nitrogen (TN) = 84.27 %, respectively. In this novel system, the autotrophic-heterotrophic denitrifying bacteria played vital role for the removal of CIP and enhanced denitrification process. Thus, autotrophic denitrifying bacteria uses CO2 and H2 as carbon sources to reduce nitrates to N2. This system has the assortment and prosperous community revealed at the current intensity of 60 mA, and the analysis of bacterial community structure in effluent samples fluctuates under different condition of C/N ratios. According to the results of LC-MS/MS analysis, the intermediate products were proposed after efficient biodegradation of CIP. Microbial community on biodegrading was mostly found at phylum, and class level was dominantly responsible for the NO3--N and biodegradation of CIP. This work can provide some new insights towards the biodegradation of CIP and the efficient removal of nitrates from low C/N wastewater treatment by the novel 3D-BER system.

A rapid, precise, accurate and low cost method for the determination of vitamin E (α-tocopherol) in cereal products and biscuits was developed. The uncertainty was calculated for the first time and the methods were performed in different cereal products and biscuits, characterized as “superfoods”. The limits of detection and quantification were calculated. Accuracy and precision were estimated using the certified reference material FAPAS T10112QC and the determined values were in good accordance with the certified values. The health claims according to the daily reference values for vitamin E were calculated and the results proved that the majority of the samples examined showed %daily value higher than 15%.