This paper describes different variants of broadband and simple attenuator modules for beamforming applications, based on Radio Frequency Micro Electro-Mechanical Systems (RF-MEMS), framed within Coplanar Waveguide (CPW) structures. The modules proposed in the first part of this work differ in their actuation voltage, topology, and desired attenuation level. Fabricated samples of basic 1-bit attenuation modules, characterized by a moderate footprint of 690 x 1960 µm2 and aiming at attenuation levels of -2, -3 and -5 dB in the 24.25-27.5 GHz range, are presented in their variants featuring both low actuation voltages (5-7 V) as well as higher values (~ 45V), the latter ones ensuring larger mechanical restoring force (and robustness against stiction). Beyond the fabrication non-idealities that affected the described samples, the substantial agreement between simulations and measurement outcomes proved that the proposed designs could provide precise attenuation levels up to 40 GHz, ranging up to nearly -3 dB and -5 dB for the series and shunt variants, respectively. Moreover, they could be effective building blocks for future wideband and reconfigurable RF-MEMS attenuators. In fact, in the second part of this work, combinations of the discussed cells and other configurations meant for larger attenuation levels will be investigated.

Diffuse midline gliomas are among the deadliest human cancers and have had little progress in treatment in the last 50 years. Cell cultures of these tumors have been developed recently, but it is unknown the degree to which such cultures retain the characteristics of the source tumors. DNA methylation profiling offers a powerful tool to look at genome-wide epigenetic changes that are biologically meaningful and can help assess the similarity of cultured tumor cells to their in vivo progenitors. Paraffinized diagnostic tissue from three diffuse intrinsic pontine gliomas with H3 K27M mutations was compared with subsequent passages of neurosphere cell cultures from those tumors. Each cell line was passaged 3-4 times and analyzed with DNA methylation arrays and standard algorithms that provided comparison of diagnostic classification and cluster analysis. All samples tested maintained high classifier scores and clustered within the reference group of H3 K27M-mutant diffuse midline gliomas. There was a gain of 1q in all cell lines, with two cell lines initially manifesting the gain of 1q only during culture. In vitro cell cultures of H3 K27M-mutant gliomas maintain high degrees of similarity in DNA methylation profiles to their source tumor, confirming their fidelity even with some chromosomal changes.

Patients with a psychotic disorder frequently report oral health problems, while mental health nurses (MHNs) seem not to be fully aware of these problems and the risk factors. Therefore, this study aims to develop supportive tools for MHNs regarding oral health to increase sensitization among MHNs and to provide MHNs with knowledge to recognize (potential) oral health problems in patients with a psychotic disorder. We used a human-centered design in which the user, MHNs as well as experts by experience, were placed in the centre of the research process. Problems and needs in MHNs working with patients with a psychotic disorder were addressed. To identify key issues of problem as well as the needs in terms of resources, we started with focus groups (n = 9). We analysed the data thematically based on context of patients and MHNs in practice regarding oral health, preferred oral health tools focused on MHN, and intended outcomes of tools. A Multi Criteria Decision Matrix was developed and analysed (n = 9) to identify the most optimal and viable solution based on established criteria and issues that are prevalent in the work of MHNs. Most promising result was the development of a brochure with an awareness screener. The brochure with awareness screener was developed as a low-fidelity prototype for MHNs regarding oral health in patients with a psychotic disorder, based on the latest scientific evidence. After testing it, the feasibility was tested through semi-structured interviews (n=19). MHNs and experts by experience were satisfied with the tool and provided recommendations for adjustments to the content. Significant augmentations to the brochure include a clinical lesson and a toothbrush with toothpaste for patients. We can conclude that a brochure with an awareness screener is feasible for MHNs. Future steps aiming to further refine and optimize care processes for oral health tools in MHNs, should take refining eligibility criteria for psychiatric populations and the language level of the target group of a tool into account.

An observational cohort study of patients diagnosed with endometrial cancer (EC) stage IA G1, or atypical endometrial hyperplasia (AHE), undergoing organ-preserving treatment, was conducted. Objective of the study: to determine CDO1, PITX2, and CDH13 gene methylation levels in early endometrial cancer and atypical hyperplasia specimens obtained before organ-preserving treatment in the patients with adequate response and with insufficient response to hormonal treatment. Materials and methods: 41 endometrial specimens obtained during diagnostic uterine curettage in women with EC (n=28) and AEH (n=13), willing to preserve reproductive function, were studied; 18 specimens of endometrial cancer IA stage G1 from peri- and early postmenopausal women (comparison group) were included in the study. The control group included 18 endometrial specimens from healthy women obtained by diagnostic curettage for missed abortion and/or intrauterine adhesions. Methylation levels were analyzed using the modified MS-HRM method. Results: All 13 women with AEH had complete response (CR) to medical treatment. In the group undergoing organ-preserving treatment for uterine cancer IA stage G1 (n=28), 14 patients had complete response (EC CR group) and 14 had not (non-CR). It was found that all groups had statistically significant differences in CDO1 gene methylation levels with the control group (p<0.001) except for the EC CR group (p=0.21). The p-value of difference between EC CR and EC non-CR groups was <0.001. The differences in PITX2 gene methylation levels between the control and study groups were also significantly different (p<0.001), except for AEH group (p=0.21). For the difference between EC CR and EC non-CR groups, the p-value was 0.43. For CDH13 gene methylation levels, statistically significant differences were found between the control and EC non-CR groups (p<0.001), and the control and EC comparison groups (p=0.005). When comparing the EC CR group with EC non-CR group, the p-value for this gene was <0.001. Simultaneous assessment of CDO1 and CDH13 genes methylation allowed to accurately distinguish between EC CR and EC non-CR groups (AUC=0.96). Conclusion: Assessment of CDO1 and CDH13 gene methylation in endometrial specimens from patients with endometrial cancer (IA stage G1), planned for medical treatment, can predict the treatment outcome.

Prostate cancer is the second leading cause of death in males in America, with advanced prostate cancers exhibiting a 5-year survival rate of only 32%. Castration-resistance is often developed during the course of treatment, though its influences require further understanding. This study explores the human microbiome for its implications in castration-resistance and metastasis in prostate cancer. RNA sequencing data was downloaded for bone and soft tissue biopsies of patients with metastatic castration-resistant prostate cancer. These sequences were mapped to bacterial sequences to yield species-level abundance approximations. Numerous species were found to correlate to the expression of known markers of castration-resistance, including AR, PI3K, and AKT. Castration-resistance-associated signaling pathways were also enriched with these species, including PI3K-AKT signaling and endocrine resistance. For their implications in cancer aggression and metastasis, cancer stem cell markers were further explored for relation to these species. EGFR and SLC3A2 were widely downregulated with greater abundance of most species. Our results suggest that the microbiome is heavily associated with castration-resistance and stemness in prostate cancer. By considering the microbiome’s importance in these factors, we may better understand the highly aggressive and highly invasive nature of prostate cancer, allowing for needed improvement in the treatment of this disease.

In the realm of the Internet of Things (IoT), a network of sensors and actuators collaborates to fulfill specific tasks. As the demand for IoT networks continues to rise, it becomes crucial to ensure the stability of this technology and adapt it for further expansion. Through an analysis of related works including Feedback-based Optimized Fuzzy Scheduling Approach (FOFSA) algorithm, Adaptive Task Allocation Technique (ATAT) and Osmosis Load Balancing algorithm (OLB), we identify their limitations in achieving optimal energy efficiency and fast decision-making. To address these limitations, this research introduces a novel approach to enhance the processing time and energy efficiency of IoT networks. The proposed approach achieves this by efficiently allocating IoT data resources in the Mist layer during the early stages. We apply the approach to our proposed system known as the Mist-based Fuzzy Healthcare System (MFHS) that demonstrates promising potential to overcome the existing challenges and pave the way for efficient Industrial Internet of Healthcare Things (IIoHT) of the future.

In this paper, we introduce a specialized, fully automated experimental arrangement designed for assessing the effectiveness of augmented and virtual reality technologies in healthcare setting and explore its design principles focusing on depth sensor characterization. The main goal of this project is to establish a robust benchtop platform for the quantitative evaluation of extended reality technologies in a controlled environment, emphasizing the practical assessment of augmented reality head-mounted devices. We outline a design concept and considerations for an experimental configuration aimed at creating a realistic testing environment. This apparatus comprises an observation platform mounted on a three-degree-of-freedom motorized system and a test phantom stage. Focusing on real-case scenarios, we utilized a range of sensors, including readily available range-sensing cameras and commercial augmented reality headsets, such as the Intel RealSense L515 LiDAR camera, mounted on the motion control system. The setup enabled automated data collection and facilitates controlled assessments and validation of various facets of augmented reality technologies, including object, hand, and head tracking, as well as static and dynamic image registration. This paper describes the system architecture, the process of automated data collection, and presents several evaluation studies conducted with this setup, providing insights into the quality and temporal noise associated with static or moving objects or observers in augmented reality applications.

Among the various types of gas sensors, the chemoresistive gas sensors based on metal oxides are considered the most attractive ones due to their simple operation, low costs and miniaturization. Thin films of V2O5 undoped and doped with TiO2 were studied as nitrogen dioxide, methane and hydrogen sensors. The experimental kinetics of the electrical conductivity changes due to introduction and removal of gas on metal oxide gas sensors were successfully explained in terms of the Langmuir adsorption theory.

Many fields of human activity benefit from the ability to create images of obscured objects placed behind walls and to map their displacement in a noninvasive way. Usually, imaging devices like Synthetic Aperture Radars (SAR) and Ground Penetrating Radars (GPR) use expensive dedicated electronics which results in prohibitive prices. This paper presents the experimental implementation and the results obtained from an imaging system capable of performing SAR imaging and interferometric displacement mapping of targets located behind walls, as well as 3D GPR imaging using a low-cost general-purpose radar sensor. The proposed solution uses for the RF section of the system a K-band microwave radar sensor module implementing Frequency Modulated Continuous Wave operation. The low-cost sensor was originally intended for simple presence detection and ranging for domestic applications. The proposed system was tested in several scenarios and proved to operate as intended for a fraction of the cost of a commercial imaging device.

The healthcare situation in Africa is characterized by limited resources and a high burden of disease, presenting significant challenges to the healthcare systems in the region. The integration of Artificial Intelligence (AI) technologies in African healthcare holds immense potential for addressing these challenges and improving health outcomes. This paper aims to provide a comprehensive understanding of the current healthcare landscape in Africa and the urgent need for AI-driven solutions.In addition to discussing the potential applications of AI in African healthcare, such as disease diagnosis, treatment planning, and medical imaging analysis, this manuscript seeks to shed light on the specific challenges hindering the implementation of AI in the region. By providing detailed examples and case studies, we aim to offer insights into the obstacles that need to be overcome and potential solutions that can be pursued.By leveraging AI technologies, Africa has the opportunity to revolutionize its health systems, bridging the gap in access to quality healthcare across the continent. The objective of this review article is to not only highlight the potential benefits that AI can bring to African healthcare but also to emphasize the urgent need for action and collaboration in implementing and scaling up AI innovations in the region. By doing so, African countries can pave the way for improved health outcomes and ensure that their populations receive the healthcare services they deserve.

This review delves into the growing field of flexible and stretchable strain sensors utilized in human gait analysis, focusing on determining knee bending angle and muscle activities when a human subject walks. Recent advancements have enabled these sensors to accurately capture biomechanical parameters while accommodating the body's natural movements. We examine the principles underlying these sensors' design and fabrication techniques, emphasizing their flexibility, stretchability, and biocompatibility for seamless integration into wearable systems. Through critical evaluation of existing methodologies, we assess the reliability and validity of these sensors in quantifying gait parameters. Furthermore, we discuss this technology's clinical and research implications, highlighting its potential in personalized rehabilitation and sports performance optimization. We provide an overview of flexible strain sensors and their application for analyzing human walking gait, especially for observing walking gait in rehabilitation programs. First, we present the basic working principles of various flexible strain sensors. Second, by the application of flexible strain sensors as walking gait monitoring. Finally, current challenges and future opportunities in this research area are discussed. By synthesizing current knowledge and outlining future directions, this review aims to provide insights for researchers and practitioners seeking to leverage flexible and stretchable strain sensors for comprehensive human gait analysis.

One of the industries with the fastest rate of growth is healthcare, and this industry's enormous data requires extensive cloud storage. The cloud may offer some protection, but there is no assurance that data owners can rely on it for refuge and privacy amenities. Therefore, it is essential to offer security and privacy protection. Increased customer satisfaction with security and privacy preservation is crucial since healthcare big data and its sources are stored in the cloud and contain increasingly private and sensitive information. However, maintaining privacy and security in an untrusted green cloud environment is difficult, thus the data owner should have complete data control. A new work SecPri-BGMPOP(security and privacy of Boost graph Convolutional Network -Pinpointing-Optimization Performance) is suggested that can offer a solution that involves several different steps in order to handle the numerous problems relating to security and protecting privacy. Initially Boost Graph Convolutional Network Clustering (BGCNC) algorithm, which reduces computational complexity in terms of time and memory measurements, is first applied to the input dataset to begin the clustering process. Second, enlarge by employing a piece of the magnifying bit string to generate a safe key, pinpointing based encryption avoids amplify leakage even if a rival or attacker decrypts the key or asymmetric encryption. Finally, to determine the accuracy of the method, an optimal key was created using a meta-heuristic algorithmic framework called Hybrid fragment horde bland lobo Optimization (HFHBLO). Our proposed method currently kept in a cloud environment, allowing analytics users to utilize it without risking their privacy or security.

Healthcare professionals constantly face situations that reflect ecosystems’ degradation. These can negatively affect their mental health. Research suggests that hope and resilience can play an important role in this scenario, since they are related to/predict mental health in highly heterogeneous samples (considering geography, age, profession, health, etc.). In this context, the aims of the present study are: to characterize and explore the relationship between hope, resilient coping and mental health of Portuguese healthcare professionals. Using Google Forms, 276 healthcare professionals answered to the GHQ-28, the (adult) Trait Hope Scale, and the Brief Resilient Coping Scale (cross-sectional study). The minimum and maximum possible scores were reached, with the exception of the maximum score of GHQ-28-Total. Regarding Hope, 19.6% scored below the midpoint (M=43.46, SD=11.97); 29.3% revealed low resilience (M=14.93, SD=4.05); and the average of 4 of the 5 Mental Health scores (exception: Severe Depression) indicates the probability of a psychiatric case. Hope correlated with Social Dysfunction and GHQ-28-Total; resilient coping proved to be a (weak) predictor of 4 of the 5 GHQ-28 indicators (exception: Severe depression). The results support the need to promote the sample's mental health, hope and resilient coping. They also suggest that stimulating resilient coping may contribute to improving healthcare professionals’ mental health.

Artificial intelligence (AI) is increasingly being used to improve the quality control of point-of-care diagnostics. This is caused by a number of factors, including the following: 1. AI can accelerate and improve testing accuracy. In comparison to humans, AI technology can review data more quickly and precisely, reducing errors and improving overall quality assurance. 2. When it comes to improving POC test findings on healthcare issues such as infectious diseases or medical crises such as heart attacks, AI can be used for sophisticated predictive analytics and modeling that aid in better decision-making. 3. Artificial intelligence facilitates process automation, increasing productivity and lowering labor costs in labor-intensive tasks such as testing and analyzing samples collected at point-of-care facilities. 4. The use of AI enables organizations implementing these solutions to gain insights from large volumes of raw diagnostic data generated faster and more accurately, allowing them to build solid frameworks around preventive care initiatives and significantly influence public health outcomes.5. Artificial intelligence (AI) has been demonstrated to be a useful tool for real-time monitoring systems that identify any problems with test results early so that they can be corrected before affected patients receive inaccurate diagnoses or treatment plans based on false information provided by diagnostic tests performed at points of care such as clinics or hospitals.Using these technologies would allow healthcare organizations to spend less on labor while still receiving exact diagnoses and rapid treatment delivery at a fraction of the cost that manual approaches required earlier.

Understanding the dynamics of teamwork and communication among healthcare professionals is crucial in the face of evolving healthcare challenges. This study assessed relational coordination among healthcare professionals in the South Tyrolean healthcare system in Italy, focusing on communication and teamwork dynamics in a cross-sectional survey. Using the validated Relational Coordination Survey (RCS) instrument and 525 completed online responses, the questionnaire aimed to understand the implications of different levels of relational coordination ratings by general practitioners, hospital physicians, nurses, and administrative personnel (response rate 26%). The demographics of the participants revealed a predominance of female professionals (64%), with an average age of 50 and 18 years of service. The resulting RCS scores varied significantly across professional groups, with nurses reporting the highest within-group scores, indicating moderate coordination, and administrators reporting the lowest scores, reflecting areas of weak coordination. Between-group relational coordination was generally perceived as weak across professional groups, with the least weakness observed between general practitioners and nurses. German or Italian language and health district affiliation emerged as significant factors influencing relational coordination ratings, highlighting the need for differentiated understanding and strategies in multilingual and diverse regional settings. Assessments of interdisciplinary feedback and referral practices highlight the variation in teamwork and communication weaknesses and underscore the need for targeted interventions to improve relational coordination. This study provides insights into the complexity of relational dynamics in health care settings. It suggests that improving relational coordination through tailored strategies could significantly improve team effectiveness, quality of patient care, and overall system efficiency.

Among magnetoelectric (ME) heterostructures, ME laminates of the type Metglas-like / PVDF (magnetostrictive+piezoelectric constituents) have shown the highest induced ME voltages, usually detected at the magnetoelastic resonance of the magnetostrictive constituent. This ME coupling happens because of the high cross-correlation coupling between magnetostrictive and piezoelectric material, and is usually associated with a promising application scenario for sensors or actuators. In this work we detail the basis of the operation of such devices, as well as some arising questions (as size effects) concerning their best performance. Also, some examples of their use as very sensitive magnetic fields sensors or innovative energy harvesting devices will be presented At the end, the challenges, future perspectives and technical difficulties that will determine the success of ME composites for sensor applications are discussed.

In this work, an innovative numerical approach for polylinear approximation (polylinearization) of non-self-intersecting compact sensor characteristics (transfer functions) specified either pointwise or analytically is introduced. The goal is to optimally partition the sensor characteristic, i.e. to select the vertices of the approximating polyline (approximant) along with their positions on, the sensor characteristics so that the distance (i.e. the separation) between the approximant and the characteristic is rendered below a certain problem-specific tolerance. To achieve this goal, two alternative non-linear optimization problems are solved, whose essential difference is in the adopted quantitative measure of the separation between the transfer function and the approximant. In the first problem, which relates to absolutely integrable sensor characteristics (their energy is not necessarily finite, but they can be represented in terms of convergent Fourier series), the polylinearization is constructed by numerical minimization of the L^1--metric (a distance-based separation measure), concerning the number of polyline vertices and their locations. In the second problem which covers the quadratically integrable sensor characteristics (whose energy is finite, but they do not necessarily admit a representation in terms of convergent Fourier series), the polylinearization is constructed by minimizing numerically the L^2-metric (area-, or energy-based separation measure) for the same set of optimization variables –the locations, and the number of polyline vertices.

Despite the importance of influenza vaccination for healthcare workers (HCWs), their uptake remains challenging. This study aimed to measure influenza vaccine hesitancy among HCWs in Nakhon Phanom province, Thailand. A representative cross-sectional survey was conducted at six hospitals during August – September 2020 using a self-administered questionnaire. HCWs delaying getting influenza vaccines, accepting but unsure, or refusing with doubts were categorized as hesitant. Those accepting without any doubts were classified as non-hesitant. Vaccine hesitancy determinants were identified by multivariable logistic regression analysis. A total of 338 participants (97%) completed the questionnaires; most were female nurses working at district hospitals without pre-existing chronic medical conditions. Nearly 60% of participants (197/338) exhibited influenza vaccine hesitancy, and significant factors included age above 50 years adjusted odds ratio [aOR] 3.2, 95% CI 1.3-8.5), fair knowledge of influenza/vaccination (aOR 0.4, 95% CI 0.2-0.8), and negative influence of other HCW (High level– aOR 2.3, 95% CI 1.1-4.8; Moderate level- aOR 2.1, 95% CI 1.1-4.4). Imparting updated information to the HCW combined with positive guidance from influential peers may help reduce this hesitancy.

This review article focuses on the role of Artificial Intelligence (AI) in transforming healthcare in Africa, specifically in combatting infectious diseases, neglected tropical diseases (NTDs), and antimicrobial resistance. We provide a comprehensive overview of the significance of AI in the healthcare industry, highlighting its urgency and importance in addressing these specific health challenges in Africa. We begin by discussing the role of AI in infectious disease surveillance and outbreak detection. We explore how AI technology can be employed for real-time tracking and prediction of outbreaks, providing examples of successful AI applications in infectious disease surveillance within the African context.Next, we examine the potential of AI-enabled diagnosis and treatment for faster and more accurate diagnoses of infectious diseases and NTDs. We highlight specific examples of AI applications in diagnosing and treating these diseases in Africa, showcasing the potential of AI to improve clinical outcomes and save lives.Furthermore, we focus on how AI-driven drug discovery and development can expedite the search for new treatments for infectious diseases and combat antimicrobial resistance. We present examples of AI applications in drug discovery within the African context, illustrating the potential for AI to revolutionize the development of effective therapeutics.In addition, we delve into how AI-powered public health interventions can enhance the design and implementation of targeted interventions. We explore how AI can optimize resource allocation and facilitate data-driven decision-making processes, providing examples of AI applications in public health in Africa.Finally, we address the challenges and limitations of implementing AI in combatting infectious diseases, NTDs, and antimicrobial resistance in Africa. We discuss potential barriers and ethical concerns surrounding AI applications in healthcare, aiming to encourage informed and responsible utilization of AI technologies.Overall, this review emphasizes the importance and potential of AI in combatting infectious diseases, NTDs, and antimicrobial resistance in Africa. It positions AI as a catalyst for revolutionizing healthcare in the region, leading to more effective disease surveillance, diagnosis, treatment, drug discovery, and public health interventions.

Plant leaf area index (LAI) is a key characteristic affecting field canopy microclimate. In addition to traditional professional measuring instruments, smartphone camera sensors have been used to measure plant LAI. However, when smartphone methods were used to measure conifer forest LAI, very different performances were obtained depending on whether the smartphone was held at the zenith angle or at a 57.5° angle. To validate further the potential of smartphone sensors for measuring conifer LAI and to find the limits of this method, this paper reports the results of a comparison of two smartphone methods with an LAI-2000 instrument. It is shown that both methods can be used to reveal the conifer leaf-growing trajectory. However, the method with the phone oriented vertically upwards always produced better consistency in magnitude with LAI-2000. The bias of the LAI between the smartphone method and the LAI-2000 instrument was explained with regard to four aspects that can affect LAI: gap fraction, leaf projection ratio, sensor field of view (FOV), and viewing zenith angle (VZA). It was concluded that large FOV and large VZA cause the 57.5° method to overestimate the gap fraction and hence underestimate conifer LAI, especially when tree height is greater than 2.0 m. For the vertically upward method, the bias caused by the overestimated gap fraction is compensated for by an underestimated leaf projection ratio.

Currently, old-style personal medicare techniques rely mostly on traditional methods, such as cumbersome tools and complicated processes, which can be time-consuming and inconvenient in some circumstances. Furthermore, such old methods need the use of heavy equipment, blood draws, and traditional bench-top testing procedures. Invasive ways of acquiring test samples can potentially cause patients discomfort and anguish. Wearable sensors, on the other hand, may be attached to numerous body areas to capture diverse biochemical and physiological characteristics as a developing analytical tool. Physical, chemical, and biological data transferred via the skin is used to monitor health in various circumstances. Wearable sensors can assess the aberrant conditions of the physical or chemical components of the human body in real-time, exposing the body state in time, thanks to unintrusive sampling and high accuracy. Most commercially available wearable gadgets are mechanically hard components attached to bands and worn on the wrist, with form factors ultimately constrained by the size and weight of the batteries required for the power supply. Wearable gadgets with “skin-like” qualities are a new type of automation that is only starting to make its way out of research labs and into pre-commercial prototypes. In this paper, we studied the recent advancement in battery-powered wearable sensors established on optical phenomena and skin-like battery-free sensors which brings a breakthrough in wearable sensing automation.

Single-phase-to-ground fault in non-effectively grounded systems poses serious public safety concern. Along with increasing deployment of low-voltage (LV) sensors, new opportunities and ways are created for solving this traditional problem in distribution systems. A new approach, identifying primary single-phase-to-ground line fault and locating it through measurement data from smart sensors deployed in the secondary side of distribution transformers, is proposed in this paper. When a fault occurs in primary distribution feeder, the transient aerial mode voltage (AMV) of each LV smart sensor is calculated. The fault line can be identified by an abrupt change value of AMV at LV side. Next, by finding the position of the maximum value of this AMV from LV sensors on the fault line, the fault location can be pinpointed to two neighboring distribution transformers. The proposed method has been proven to be efficient and reliable by simulation studies.

This research addresses a gap in the literature by conducting a comprehensive analysis of patients’ level of satisfaction with dental care. Methods: By combining quantitative and qualitative survey methods with the PSQ questionnaire this study aims to augment ongoing initiatives to enhance dental patients’ experiences by painting a more comprehensive depiction of patients' level of satisfaction; Results: When asked about their overall level of satisfaction 77,1% of the patients said they received excellent services from the office personnel and 72,2% said they trust their doctors; Conclusions: Assessing patient satisfaction in the realm of dental services quality is crucial for enhancing service quality and accuracy, benefiting both patients and dentists, and ultimately improving public health.

Contaminants of Emerging Concern (CECs), a new category of contaminants in limelight, is a major issue of global concern. The pervasive nature of CECs and its harmful effects, such as cancer, reproductive disorders, neurotoxicity etc., make the situation alarming. The perilous nature of CECs lies in the fact that even very small concentration of CECs can cause great impacts on living beings. It also has a nature of bioaccumulation. Thus, it is the ultimate need to have efficient sensors for detection of CECs to ensure safe living environment. Electrochemical sensors are an efficient platform for CEC detection as they are highly selective, sensitive, stable, reproducible, and prompt, and can detect very low concentrations of analyte. Major classes of CECs are pharmaceuticals, illicit drugs, personal care products, endocrine disruptors, newly registered pesticides, and disinfection by-products. This review focusses on CECs, including their sources and pathways, health effects caused by them, and electrochemical sensors as reported in literatures under each category for the detection of major CECs.

Structural deformations are one of the most significant factor that affects machine tool (MT) positioning accuracy. These induced errors are complex to be represented by a model, nevertheless they need to be evaluated and predicted in order to increase the machining performance. This paper presents a novel approach to calibrate a machine tool in real-time, analyzing the thermo-mechanical errors through Fibre Bragg Grating (FBG) sensors embedded in the MT frame. The proposed configuration consists of an adaptronic structure of passive materials, Carbon Fibre Reinforced Polymers (CFRP), equipped by FBG sensors that are able to measure in real-time the deformed conditions of the frame. By using a proper thermo-mechanical kinematic model, the displacement of the end effector may be predicted and corrected when it is subjected to external undesired factors. By starting from a set of FE simulations to develop a model able to describe the MT structure stresses, a prototype has been fabricated and tested. The scope was to compare the numerical model with the experimental tests using FBG sensors. The experimental campaign has been performed varying the structure temperature over time and measuring the tool tip point (TTP) positions. The obtained results showed a substantial matching between the real and the predicted position of TTP confirming the effectiveness of the proposed calibration system.

Sterol homeostasis in mammalian cells and tissues involves balancing three fundamental processes: de novo sterol biosynthesis; sterol import (e.g., from blood-borne lipoproteins); and sterol export. In complex tissues, composed of multiple different cell types (such as the retina), import and export also may involve intra-tissue, inter-cellular sterol exchange. Disruption of any of these processes can result in pathologies that impact the normal structure and function of the retina. Here, we provide a brief overview of what is known currently about sterol homeostasis in the vertebrate retina and offer a proposed path for future experimental work to further our understanding of these processes, with relevance to the development of novel therapeutic interventions for human diseases involving defective sterol homeostasis.

Background: Mental capacity is a fundamental aspect that enables patients to fully par-ticipate in various healthcare procedures. To assist healthcare professionals (HCPs) in assessing patients' capacity, especially in the mental health field, several standardized tools have been developed. These tools include the MacArthur Competence Assessment Tool for Treatment (MacCAT-T), the MacArthur Competence Assessment Tool for Clinical Research (MacCAT-CR), and the Competence Assessment Tool for Psychiatric Advance Directives (CAT-PAD). The core dimensions explored by these tools include Understanding, Appreciation, Reasoning, and Expression of a choice. Objective: This meta-analysis aimed to investigate potential differences in deci-sion-making capacity within the healthcare context among groups of patients with bi-polar disorder (BD) and schizophrenia spectrum disorder (SSD). Methods: A systematic search was conducted on Medline/Pubmed, and Scopus. Addi-tionally, Google Scholar was manually inspected, and a manual search of emerging re-views and reference lists of the retrieved papers was performed. Eligible studies were specifically cross-sectional, utilizing standardized assessment tools, and involving pa-tients diagnosed with BD and SSD. Data from the studies were independently extracted and pooled using random-effect models. Hedges g was used as a measure for outcomes. Results: Six studies were identified, with three studies using the MacCAT-CR, two studies the MacCAT-T, and one the CAT-PAD. The participants included 189 individuals with BD and 324 individuals with SSD. The meta-analysis revealed that patients with BD performed slightly better, and the difference was statistically significant, compared to patients with SSD, particularly in the domain of Appreciation (ES=0.23, 95% CI: 0.01 to 0.04, p=0.037). There was no statistically significant difference between the two groups for Understanding (ES=0.09, 95% CI: - 0.10 to 0.27, p=0.352), Reasoning (ES=0.18, 95% CI: - 0.12 to 0.47, p=0.074), and Expression of a choice (ES = 0.23, 95% CI: - 0.01 to 0.48, p=0.60). In the sensitivity analysis, furthermore, when considering only studies involving patients in symptomatic remission, the difference for Appreciation also resulted in non-significant (ES=0.21, 95% CI: -0.04 to 0.46, p=0.102). (ES=0.21, 95% CI: -0.04 to 0.46, p=0.102). Conclusions: These findings indicate that there are no significant differences between patients with BD and SSD during remission phases, while differences are minimal during acute phases. The usefulness of standardized assessment of capacity at any stage of the illness should be considered, both for diagnostic-therapeutic phases and for research and advance directives. Further studies are necessary to understand the reasons for the overlap in capacity between the two diagnostic categories compared in this study.

Ambulatory heart rate (HR) monitors that acquire electrocardiogram (ECG) or/and photoplethysmographm (PPG) signals from the torso, wrists, or ears are notably less accurate in tasks associated with high levels of movement compared to clinical measurements. However, reliable estimation of HR can be obtained through data fusion from different sensors. These methods are especially suitable for multimodal hearable devices, where heart rate can be tracked from different modalities, including electrical ECG, optical PPG, and sounds (heart tones). Combined information from different modalities can compensate for single source limitations. In this paper, we evaluate the possible application of data fusion methods in hearables. We assess data fusion for heart rate estimation from simultaneous in-ear ECG and in-ear PPG, recorded on eight subjects while performing 5-minute sitting and walking tasks. Our findings show that data fusion methods provide a similar level of mean absolute error as the best single-source heart rate estimation but with much lower intra-subject variability, especially during walking activities. We conclude that data fusion methods provide more robust HR estimation than a single cardiovascular signal. These methods can enhance the performance of wearable devices, especially multimodal hearables, in heart rate tracking during physical activity.

In mining machines with friction discs, but also in multi-rope traction elevators, it is necessary to distribute the applied tensile load, generated by the weight of the cage and counterweight, evenly in all cross-sections of the load-bearing ropes. Hydraulic devices used for this purpose can operate on the principle of Pascal's law. The article presents a structural design, a 3D model and an implemented solution of a laboratory device capable of simulating a practical method of evenly distributing the total weight of the load into partial tensile forces of the same size acting on a selected number of load-bearing ropes. The laboratory equipment uses two pairs of three steel cables of finite length for the simulations. During the experimental measurements, tensile forces derived from the tractive force of the piston rods, pushed into the bodies of the hydraulic cylinders by the pressure of the hydraulic oil supplied through the pipeline under the pistons of the hydraulic cylinders, were detected. The resulting amount of hydraulic oil pressure in the hydraulic circuit influenced by different values of the hydraulic oil pressures in the hydraulic cylinders and by the pressure in the supply pipe was experimentally studied on the laboratory equipment. Simulations were also carried out in order to detect the hydraulic oil pressure in the hydraulic circuit caused by the change in the different magnitudes of the tensile forces in the ropes From the experiments carried out, it follows that with the appropriate choice of hydraulic elements and the design of the hydraulic circuit, the weight of the load, acting as the total pulling force in the ropes, can be evenly distributed (with a deviation of up to 5%) to all cross-sections of the load-bearing ropes. If the exact values of the hydraulic oil volumes under the pistons of all hydraulic cylinders are not known, it is not possible to calculate the pressure values in the hydraulic circuit when the valves of the hydraulic pipes are gradually opened.

Background: Virtual care adoption accelerated during the COVID-19 pandemic, highlighting the need for healthcare professionals to develop relevant competencies. However, limited evidence exists on the core competencies required for quality virtual care delivery. Objective: This study aimed to identify the critical competencies physicians, nurses, and other health professionals need for adequate virtual care provision in Saudi Arabia using a Delphi method. Methods: A 3-round Delphi technique was applied with a panel of 42 experts, including policymakers, healthcare professionals, academicians, and telehealth specialists. In round 1, an open-ended questionnaire elicited competencies needed for virtual care. Competencies were distilled and rated for importance in rounds 2 and 3 until consensus was achieved. Results: Consensus emerged on 151 competencies across 33 domains. The most prominent domains were communication (15 competencies), professionalism (13), leadership (12), health informatics (5), digital literacy (5) and clinical expertise (11).

The quality of healthcare services is a very important indicator of social welfare in developed and emerging countries. Good quality levels are critical to ensuring patient safety, improving health outcomes, increasing patient satisfaction, optimizing resource utilization, and meeting regulatory requirements. The stable and sustainable operation of medical institutions urgently requires the establishment of a reliable and effective medical quality performance evaluation platform. However, the complexity of the evaluation process, involving numerous evaluators and the consideration of different subjective and objective criteria, poses significant challenges and essentially constitutes a group multi-criteria decision-making problem. This article uses the overall medical environment of the institution, medical service attitude, medical security, administrative service measures, etc. as measurement standards to deal with this challenge. It proposes a medical service quality measurement model suitable for both qualitative and quantitative analysis. In view of the heterogeneity of information, the two-tuple fuzzy language calculation method is introduced to enable evaluators to skillfully manage diverse information and effectively avoid potential information omission problems in the subjective evaluation integration process. The effectiveness and feasibility of the model were demonstrated by applying it to the operational framework of a medical institution in central Taiwan.

Toll-like receptor 4 (TLR4) is a member of the TLR family. Members of the TLR family play an important role in innate immune responses and are induced by recognition of pathogen-associated molecular patterns. They are also involved in cell proliferation and apoptosis in cancer. We investigated the role of TLR4 in apoptotic cell death in gynecological cancer cells; gynecological cancer is associated with infertility and spontaneous abortion. To examine the effect of TLR4 activation on apoptotic signaling in cancer cells, cultured primary cancer cells were treated with the TLR4 agonist lipopolysaccharide (LPS). The morphology of cancer cells was compared with normal myometrial cells. Enhanced growth rate and loss of contact inhibition with cellular overlap was observed in the cancer cells. The molecular mechanism analysis revealed differential expression of tumor suppressor genes in LPS-treated cancer cells. The expression of apoptosis-related caspase-3 was increased significantly in cancer cells with TLR4 activation after exposure to LPS. Taken together, these results suggest the pro-apoptotic activity of TLR4 as a potential therapeutic target for the treatment of gynecological cancers.

Membrane-based sensors (MePSs) exhibit remarkable precision and sensitivity in detecting pressure changes. MePSs are commonly used to monitor catalytic reactions in solution, generating gas products crucial for signal amplification in bioassays. They also allow catalyst quantification by indirectly measuring the pressure generated by the gaseous products. This is particularly interesting to detect enzymes in biofluids associated with disease onset. To enhance the performance of a MePS, various structural factors influence membrane flexibility and response time, ultimately dictating the device's pressure sensitivity. In this study, we fabricated MePSs using polydimethylsiloxane (PDMS) and investigated how structural modifications affect the Young's modulus (E) and residual stress (σ0) of the membranes. These modifications have a direct impact on the sensors' sensitivity to pressure variations, observed as a function of the volume of the chamber (Σ) or of the mechanical properties of the membrane itself (S). MePSs exhibiting the highest sensitivities were then employed to detect catalyst quantities inducing the dismutation of hydrogen peroxide, producing dioxygen as gaseous product. As a result, catalase enzyme was successfully detected using these optimized MePSs, achieving a remarkable sensitivity of (22.7 ± 1.2) µm/nM and a limit of detection (LoD) of 396 pM.

Background: The workplace burnout syndrome is often associated with particular aspects of certain job positions, especially those which entail working with people with special needs. The burnout syndrome in healthcare jobs is a serious problem which has grown into an epidemic among healthcare workers and associates. Objectives: The aim of this research is to assess the presence of stress and burnout syndrome at work with healthcare workers, expert workers, professional associates and associates in social service institutions in Belgrade. Material and Methods: This research has been conducted in the form of a cross-sectional study of a representative sample in social institutions in Belgrade. It has been conducted from March to the end of June of 2023. The sample of the study had 491 participants. The questionnaires used were a structured instrument with social-demographic and social-economic characteristics, workplace characteristics, life style characteristics, and the following questionnaires: DASS-21, Copenhagen, Brief Resilience Scale, and Brief Resilient Coping Scale. Results: The end results indicate the following to be significant risk factors for the occurrence of workplace burnout syndrome: overtime (OR=2.62; CI=1.50-4.56), BRS average score (OR=0.28; CI=0.17-0.44), DASS21 D heightened depression (OR=2.09; CI=1.1-4.04), DASS21 A heightened anxiety (OR=2.38; CI=1.34-4.21), DASS21 S heightened stress (OR=2.08; CI=1.11-3.89). The only protective risk factor which stood out was the self-assessment of health levels (OR=0.60; CI=0.42-0.85). Conclusion: Overtime is a significant predictor of workplace burnout. Apart from it, other significant predictors of workplace burnout were heightened depression, anxiety, and stress levels.

Noninvasive brain stimulation technique can be used for modulation of motor behaviors such as reaction time (RT). The main aim of this study was to investigate whether RT during a sequential visual isometric pinch task (SVIPT) can be affected by anodal transcranial direct current stimulation (a-tDCS) over three different stimulation sites such as dorsolateral prefrontal cortex (DLPFC), primary motor cortex (M1) or posterior parietal cortex (PPC). We also aimed to assess if stimulation of these cortical sites affect the transfer of learning during SVIPT. A total of 48 right-handed healthy participants were randomly assigned to one of the four a-tDCS groups: 1) left M1, 2) left DLPFC, 3) left PPC and 4) sham. A-tDCS was applied concurrent with SVIPT in which the participants were precisely controlled their forces to reach seven different target forces from 10 to 40% of maximum voluntary contraction (MVC) presenting on a computer screen with right dominant hand. Four test blocks were randomly performed at baseline and 15 min after the intervention including sequence and random blocks with either hand. Our results showed significant differences between a-tDCS groups on ratio RT in the sequence blocks of both the right trained (P = .041) and left untrained hands (P = .023) for target forces of 15% and 30 % of MVC, respectively. In sequence blocks, M1 showed significant elongation in ratio RT for the target force of 15% and 30 % MVC compared to PPC and Sham groups in the right hand. In sequence blocks with left hand, this negative effect were found between M1-DLPFC and M1-Sham groups. In random blocks, no significant differences were found among four groups at each target forces for the left hand while there were significant differences for 15% (P =. 04) and 40% MVC (P =. 035) in the right hand. Our findings suggest that three different stimulation sites (DLPFC, M1 or PPC) were differentially affected by a single session of a-tDCS at some target forces during SVIPT. The effects of a-tDCS on ratio RT were transferred in the left untrained hand for sequence blocks but not random blocks. Further research is needed to understand fundamental aspects of these main areas of the brain on temporal processing in a precision control task such as SVIPT.

This paper comprehensively reviews sensors and sensing devices developed or/and proposed so far utilizing two smart materials: electrorheological fluids (ERFs) and magnetorheological materials (MRMs) whose rheological characteristics such as stiffness and damping can be controlled by external stimuli, an electrical voltage for ERFs and a magnetic field for MRMs, respectively. In this review article, the MRMs are classified into magnetorheological fluid (MRF), magnetorheological elastomer (MRE) and magnetorheological plastomer (MRP). To easily understand the history of sensing research using the two smart materials, the order of this review article is organized in a chronological manner of ERF sensors, MRF sensors, MRE sensors and MRP sensors. Among many sensors fabricated from each smart material, one or two sensors or sensing devices are adopted to discuss on the sensing configuration, working principle and specifications such as accuracy and sensitivity. Some sensors adopted in this article include force sensor, tactile device, strain sensor, wearable bending sensor, magnetometer, display device and flux measurement sensor. After briefly describing what have been reviewed in a conclusion, several challenging future works, which should be done for practical applications as sensors or sensing devices, are remarked in terms of new technologies such as artificial intelligence neural network in which several parameters affecting the sensor signals can be precisely tuned or controlled. It is sure that this review article is very helpful to make creative sensors using not only the proposed smart materials but also several different types of smart materials including shape memory alloys and active polymers.

Fragile X syndrome (FXS) is the most frequent monogenic form of autism spectrum disorder (ASD). Autistic FXS is caused by loss of the fmr1 gene product, the fragile X mental retardation protein (FMRP), triggering physiological and behavioral abnormalities. It is correlated with clock components for behavioral circadian rhythm. Mutation of this gene causes the disturbances in sleep patterns and circadian behavior commonly observed in patients with autistic FXS, accompanied by frequent dysregulation of melatonin synthesis and melatonin-dependent signaling. These changes impair vigilance, learning and memory, and are also linked to autistic behavior including the abnormal anxiety response. However, although several possible causes, symptoms, and clinical features of ASD have been investigated, the correlation between an altered circadian rhythm and autistic FXS has not been extensively studied. Recent works have highlighted the impact of melatonin on the nervous, immune, and metabolic systems. Even though utilization of melatonin for sleep disorder in ASD has been considered in clinical research, further studies should be aimed at its neuroprotective role in ASD during developmental period. In this review, we focus on the regulatory circuits involved in melatonin dysregulation and circadian system disruption in those with autistic FXS. Additionally, we discuss the neuroprotective effect of melatonin intervention. This may improve neuroplasticity and physical capability. We also review the underlying molecular mechanisms, and suggest that melatonin may be a useful novel treatment for autistic FXS, countering the adverse effects of circadian variation.

Hybrid forecasting methods have emerged as a solution surpassing the limitations of both statistical and deep learning approaches. While the first emphasize the significance of variables, they often produce worse forecasting results when compared to newer techniques. In contrast, deep learning models remain enigmatic "black boxes" in terms of interpretability, although achieving better results in forecasting. This article introduces the Comprehensive Cross-Correlation and Lagged Linear Regression Deep Learning (CCLR-DL) framework, designed to harness the best of both approaches, enhancing forecasting accuracy while retaining model interpretability through a feature selection process. CCLR-DL blens cross-correlation analysis, lagged multiple linear regression and granger's causality procedures with deep learning architectures based on LSTM. In a practical demonstration, CCLR-DL was applied to a real database of clinical visits associated to diagnoses in Catalonia, Spain (tracking a population of 6.3 million patients during 10 years). Predicting visits enables the healthcare managers to be ready for future demand shifts. Results demonstrate a consistent and substantial improvement over standalone statistical and deep learning methods when predicting healthcare demand. This hybrid approach not only showcases its efficacy but also offers a promising solution to the challenge of balancing predictive accuracy with model explicability. In this context, this work aims to design and validate a method for feature selection and forecasting of multivariate high dimensional time series datasets not only to improve prediction accuracy but also to model transparency by identifying a subset of variables that improve predictions and G-cause the target variable.

Tooth decay, also known as caries, is a significant medical problem that harms teeth. Treatment is based on the removal of the carious material and then filling the cavity left in the tooth, most commonly with amalgam or composite resin. The consequences of filling failure include repeating the filling, or performing another treatment, such as a root canal, or extraction. Dental amalgam contains mercury, and there is a global effort to reduce its use. However, no consensus has been reached using randomized clinical trials, regarding whether amalgam or composite resin materials are more durable, and which is the best restorative material. To determine which material is superior, we performed a retrospective cohort study using a large database where members of the 58 dental clinics with 440 dental units were treated. The number of failures of the amalgam compared to composite resin restorations between 2014 and 2021 were compared. Our data included information from over 650,000 patients. Between 2014 - 2021, 260,905 patients were treated. 19,692 out of 113,281 first amalgam restorations failed (17.49%), whereas significantly fewer composite restorations failed (11.98%) 65,943 out of 555,671. This study indicates that composite is superior to amalgam and therefore it is reasonable to cease using mercury containing amalgam.

Sensors and actuators are fundamental units in Cyber-Physical and Internet of Things systems. Because they are included in a variety of systems, using many technologies, it is very useful to characterize their functions abstractly by describing them as Abstract Entity Patterns (AEPs), that are patterns that describe abstract conceptual entities. For concreteness, we study them here in the context of autonomous cars. An autonomous car is a complex system because, in ad-dition to its own complex design, it interacts with other vehicles and with the surrounding in-frastructure. To handle these functions, it must incorporate various technologies from different sources. An autonomous car is an example of a Cyber-Physical System, where some of its func-tions are performed by Internet of Things units. Sensors are extensively used in autonomous cars to measure physical quantities; actuators are commanded by controllers to perform appro-priate physical actions. From AEPs we can derive concrete patterns, a structure combining re-lated AEPs is an Entity Solution Frame (ESF). Both sensors and actuators are susceptible to mali-cious attacks due to the large attack surface of the system where they are used. Our work is in-tended to make autonomous cars more secure, which also increases their safety. Our final objec-tive is to build a Security Solution Frame for sensors and actuators of autonomous cars that will facilitate their secure design. A Security Solution Frame is a solution structure that groups to-gether and organizes related security patterns. This article is the first stage of a secure unit that can be used to design not only secure autonomous cars but also any system where sensors and actuators are used. This paper concentrates on AEPs and ESFs for sensors and actuators; that is, on the functional aspects of these devices.

Magnetic sensors are widely used in health management systems for turbomachinery, but their applications in the hot zone are limited due to the loss of magnetic properties by permanent magnets with increasing temperature. The paper presents and verifies models and design solutions aimed at improving the performance of an inductive sensor for measuring the motion of rotating objects operating at elevated temperatures (200-1000C), such as compressor and turbine blades. Physical, analog and mathematical models of the interaction of blades with the sensor were developed. A prototype of the sensor was made and its tests were carried out on the RK-4 rotor rig for the speed of 7000 rpm, in which the temperature of the sensor head was gradually increased to 1100C. The sensor signal level was compared to that of an identical sensor operating at room temperature. The heated sensor works continuously producing the output signal whose level does not change significantly. What is more, a set of six probes passed an initial engine test in an SO-3 turbojet. It was confirmed that the proposed design of the inductive sensor is suitable for blade health monitoring of the last stages of compressors, steam turbines as well as previous generation gas turbines operating below 1000C, even without a dedicated cooling system. In real-engine applications, sensor performance will depend on how the sensor is installed and the available heat dissipation capability

Plasmonic sensors exploiting the Localized Surface Plasmon Resonance (LSPR) of noble metal nanoparticles are common in the visual spectrum. However, for bio-sensors the near infra-red (NIR) windows (600 nm – 900 nm and 1000 nm -1400 nm) are of interest, as it is a region where the absorption coefficient of water, melaninm deoxy- and hemoglobin are all low. The first part of this paper reviews the work that has been undertaken on using gold (Au) and silver (Ag) particles in Metal Enhanced Fluorescence (MEF) in the NIR. Despite this success there are limitations, as there is only a narrow band in the visual and NIR where losses are low for traditional plasmonic materials. Further, noble metals are not compatible with standard silicon manufacturing processes, making it challenging to produce on-chip integrated plasmonic sensors with Au or Ag. Therefore, it is desirable to use different materials for plasmonic chemical and biological sensing, that are foundry-compatible with silicon (Si) and germanium (Ge). One material that has received significant attention is highly doped Ge which starts to exhibit metallic properties at a wavelength as short as 6 μm. This is discussed in the second part of the paper and the results of recent analysis are included.

The world is facing a great technological transformation towards full autonomous vehicles, where optimists predict that by 2030, autonomous vehicles will be sufficiently reliable, affordable and common to displace most human driving. To cope with these trends, reliable perception systems must enable vehicles to hear and see all the surroundings, being light detection and ranging (LiDAR) sensors a key instrument for recreating a 3D visualization of the world in real time. However, perception systems must rely in accurate measurements of the environment. Thus, sensors must be calibrated and benchmarked before being placed on the market or assembled in a car. This article presents an Evaluation and Testing Platform for Automotive LiDAR sensors with the main goal of testing not only commercially available sensors, but also sensor prototypes currently under development in Bosch Automotive Electronics division. The testing system can benchmark any LiDAR sensor under different conditions, recreating the expected driving environment to which such devices are normally subjected. To characterize and validate the sensor under test, the platform evaluates several parameters such as the field of view (FoV), angular resolution, sensor’s range, etc. This project results from a partnership between the University of Minho and Bosch Car Multimedia Portugal, S.A.

This paper present a platform for airborne sensor applications using low-cost, open-source components carried by an easy-to-fly unmanned aircraft vehicle (UAV). The system, available in open-source [1], is designed for researchers, students and makers for a broad range of their exploration and data-collection needs. The main contribution is the extensible architecture for modularized airborne sensor deployment and real-time data visualisation. Our open-source Android application provides data collection, flight path definition and map tools. Total cost of the system is below 800 dollars. The flexibility of the system are illustrated by mapping the location of Bluetooth beacons (iBeacons) on a ground field and by measuring water temperatures in a lake.

The Work Ability Index (WAI) is the most widely used questionnaire for the self-assessment of working ability. Because of its different applications, shorter versions, and widespread use in healthcare activities, it is worthwhile assessing its characteristics. The WAI was distributed online among the workers of a healthcare company; the results were compared with data contained in the workers' personal health records and with absence registers. 340 out of 575 workers (59.1%) participated; 6.5% of them reported poor work ability. Exploratory factor analysis indicated that the one-factor version best described the characteristics of the WAI. The scores of the complete WAI, the shorter form without the list of diseases, and the minimal one-item version (WAS) had equal distribution and were significantly correlated. The WAI score was inversely related to age and significantly lower in women than in men, but it was higher in night workers than in colleagues due to the probable effect of selective factors. The WAI score was also correlated with absenteeism, but no differences were found between males and females in the average number of absences, suggesting that cultural or emotional factors influence the self-rating of the WAI. Workers tended to overreport illnesses in the online survey compared to data collected during occupational health checks. Musculoskeletal disorders were the most frequently reported illnesses (53%). Psychiatric illnesses affected 21% of workers and had the greatest impact on work ability. Multilevel ergonomic and human factor intervention seems to be needed to recover the working capacity of healthcare workers.

Since the systematic evolution of ligands by exponential enrichment (SELEX) method was developed, aptamers have made significant contributions as bio-recognition sensors. Microdevice systems allow for low reagent consumption, high-throughput of samples, and disposability. Due to these advantages, there has been an increasing demand to develop microfluidic-based aptasensors for analytical technique applications. This review introduces the principal concepts of aptasensors and then presents some advanced applications of microdevice-based aptasensors on several platforms. Highly sensitive detection techniques such as electrochemical and optical detection have been integrated into lab-on-a-chip devices and researchers have moved towards the goal of establishing point-of-care diagnoses for target analyses.

In urban areas like Chicago, daily life extends above ground level due to prevalence of high-rise buildings where residents and commuters live and work. This study examines the variation in fine particulate matter (PM2.5) concentrations across building stories. PM2.5 levels were measured using PurpleAir sensors, installed between April 8 and May 7, 2023, on floors one, four, six, and nine of an office building in Chicago. Additionally, data were collected from a public outdoor PurpleAir sensor on the fourteenth floor of a condominium located 800 meters away. Results show that outdoor PM2.5 concentrations peak at 14 meters height, then decline by 0.11 μg/m3 per meter elevation, especially noticeable from midnight to 8 AM under stable atmospheric conditions. Indoor PM2.5 concentrations increase steadily by 0.02 μg/m3 per meter elevation, particularly during peak work hours, likely caused by greater infiltration rates at higher floors. Both outdoor and indoor concentrations peak around noon. We find that indoor and outdoor PM2.5 are positively correlated, with indoor levels consistently remaining lower than outside levels. These findings align with previous research suggesting decreasing outdoor air pollution concentrations with increasing height. The study informs decision-making by community members and policymakers regarding air pollution exposure in urban settings.

Alcoholic liver disease (ALD) is a major cause of chronic liver disease. This term covers a broad spectrum of liver lesions, from simple steatosis to alcoholic hepatitis and cirrhosis. The patho-genesis of ALD is multifactorial and not fully elucidated due to complex mechanisms related to direct ethanol toxicity with subsequent hepatic and systemic inflammation. The accumulation of pro-inflammatory cytokines and the reduction of anti-inflammatory cytokines promote the development and progression of ALD. To date, there are no targeted therapies to counteract disease progression and prevent acute liver failure. Corticosteroids reduce mortality by acting on the hepatic-systemic inflammation. On the other hand, several studies analyzed the effect of the inhibition of pro-inflammatory cytokines and the stimulation of anti-inflammatory cytokines as potential therapeutic targets in ALD. This narrative review aims to clarify the role of the cy-tokines in the pathogenesis and treatment of ALD.

One of the most promising advancements in healthcare is the application of digital twin technology. Digital twins are virtual replicas of real-world human patients and can be used for monitoring, and diagnosis, and as a tool to design treatment strategies tailored to individual patients. Furthermore, digital twins could also be helpful in finding novel treatment targets and predicting the effects of drugs and other chemical substances in development. This review article delves into the various data sources and methodologies that contribute to the construction of digital twins. Each data source, including blood glucose levels, heart MRI and CT scans, cardiac electrophysiology, written reports, and multi-omics data, comes with different challenges regarding standardization, integration, and interpretation. We showcase how various datasets and methods are used to overcome these obstacles and generate a digital twin. While digital twin technology has seen significant progress, there are still hurdles in the way to achieving a fully comprehensive patient digital twin. Developments in non-invasive and high-throughput data collection, as well as advancements in modeling and computational power will be crucial to improve digital twin systems. We discuss a few critical developments in light of the current state of digital twin technology. Despite challenges, digital twin research holds great promise for personalized patient care and has the potential to shape the future of healthcare innovation.

HIV infection invariably attracts the attention of medical staff in complex medical specialties. To achieve the goal of elimination by 2020, various approaches are required, including the establishment of prevention, diagnosis, monitoring, treatment, control measures. These should be supported by statistical studies that report on restricted or extended geographical areas, to the level of social class and age. Such an approach, combing the medical and social science perspectives (medicosocial) can prove useful for developing control measures. Due to the complexity of this immunodeficiency pathology, the condition also attracts comorbidities (most notably tuberculosis). Hence, prospective strategies need to be developed and oriented towards the goal of eradicating HIV infection. This paper presents strategies for consideration.

The rise in the volume, variety and complexity of data in healthcare has made it as a fertile-bed for Artificial intelligence (AI) and Machine Learning (ML). Several types of AI are already being employed by healthcare providers and life sciences companies. The review summarises a classical machine learning cycle, different machine learning algorithms; different data analytical approaches and successful implementation in haematology. Although there are many instances where AI has been found to be great tool that can augment the clinician’s ability to provide better health outcomes, implementation factors need to be put in place to ascertain large-scale acceptance and popularity.

Health information technology has been widely used in healthcare, which has contributed a huge amount of data. Health data has four characteristics: high volume; high velocity; high variety and high value. Thus, they can be leveraged to i) discover associations between genes, diseases and drugs to implement precision medicine; ii) predict diseases and identify their corresponding causal factors to prevent or control the diseases at an earlier time; iii) learn risk factors related to clinical outcomes (e.g., patients’ unplanned readmission), to improve care quality and reduce healthcare expenditure; and iv) discover care coordination patterns representing good practice in the implementation of collaborative patient-centered care. At the same time, there are major challenges existing in data-driven healthcare research, which include: i) inefficient health data exchanges across different sources; ii) learned knowledge is biased to specific institution; iii) inefficient strategies to evaluate plausibility of the learned patterns and v) incorrect interpretation and translation of the learned patterns. In this paper, we review various types of health data, discuss opportunities and challenges existing in the data-driven healthcare research, provide solutions to solve the challenges, and state the important role of the data-driven healthcare research in the establishment of smart healthcare system.

Applications for Wireless Sensor Networks (WSNs) range from monitoring the environment to automating factories. However, sustained and effective functioning is made more difficult by Sensor Nodes (SNs) limited energy supplies in which optimization is the main issue. So with the aim of increasing the lifespan by decreasing the energy consumption of WSN, Low-Energy Adaptive Clustering Hierarchy (LEACH) protocol with Deep Learning (DL) algorithm is analyzed in this paper. LEACH is a hierarchical mechanism that elects Cluster Heads (CHs) and regularly rotates their positions in order to allocate energy use effectively by using the same amount of energy. However, Deep Learning (DL) method is used to further improve energy optimization. In many applications, the types of Deep Learning methods like Artificial Neural Networks (ANNs) have shown to be very useful. Using this method, WSNs may make more efficient decisions that reduce energy consumption. Data aggregation, duty cycling, and transmission protocols may all be optimized by Deep Learning model's ability to recognize patterns and forecast network behavior. This results in lower energy consumption, a longer lifespan for the network, and better overall performance.

Improving the quality and access to healthcare services in rural areas is fundamental to develop sustainable healthcare systems. This research aims to explore the motivations of healthcare professionals to work and settle in rural island areas of Greece with limited access to secondary and tertiary care. The study suggests practical ways to encourage self-motivation and attract more health workers in rural areas. An exploratory qualitative research approach was employed, involving semi-structured interviews with 16 healthcare professionals working in primary care units that lack direct hospital or hospital-health center access. The research was conducted specifically in the rural islands of Cyclades. Thematic analysis was conducted to identify common themes and unique insights from the participants. The analysis revealed three thematic categories. Τhe «attraction» thematic was influenced by personal factors, random selection, origin, accommodation factors, professional factors and obligatoriness. The «recruitment» thematic was associated with understaffing, special care issues, unstable working environment, educational and organizational aspects, and insular lifestyle. The thematic of «retention» highlighted personal issues, accommodation difficulties, economic and work-related issues, and unique challenges posed by an insular lifestyle. This research provides valuable insights into the motivations that drive healthcare professionals to settle, work, and remain in remote island units, as well as the challenges they encounter in making this decision. The study proposes strategies to motivate and attract more healthcare professionals to rural areas. These findings should be considered when formulating or reviewing primary healthcare empowerment policies to ensure equitable healthcare access for all individuals.

Electrochemical sensors have been used for many decades. Yet, modeling of such sensors used in electrolysis mode is poorly documented, especially in the case parallel action of multiple gases. Those ones are of great interest since they constitute the first brick to bring information on natures and concentrations of a gaseous mixture composition thanks to grey box modeling of sensors array for example. Based on Butler Volmer’s equations, a model assuming parallel reactions at gold cathode has been introduced in this article and confronted to experimental results. Establishment of the model is based on the extraction of 3 variables: the charge transfer coefficient “α”, the reaction order γ, and the reaction constant rate k0. Tests performed without pollutants and with different concentrations of oxygen could be nicely fitted by the model. Then, the influence of polarization current on the 3 variables of the model has been evaluated showing a clear influence on the constant rate and the reaction order. Also, increasing the polarization current enabled us to get selectivity to oxidant gases. Similarly, the effect of the oxygen concentration was evaluated. Results showed that, in this case, the charge transfer coefficients “α” obtained for oxidant gases is quite different that the ones obtained in the polarization current varying conditions. Therefore, the model will be interesting in situations where polarization current and oxygen content are not varied together. Variation of polarization current can be quite interesting to get increased information for multivariate analysis purpose in constant oxygen content situations. Besides, other parameters have are required for applications in which the oxygen content is bound to change like exhaust gases or combustion.

This study investigates novel ferrocene-based electrochemical sensors for metal cation detection through the design, synthesis and characterisation of ferrocene derivatives. Specifically, the re-search determines the redox potentials of ferrocene versus decamethylferrocene to provide in-sight into the redox potential variations between them. The investigation also examines how electrochemical oxidation of the ferrocene moiety can modulate host affinity for transition metals cations via effects such as electrostatic interactions and changes to coordination chemistry. Metal ion coordination to receptors containing functional groups like imine and quinoline is explored to elucidate selectivity mechanisms. These findings advance the fundamental understanding of ferrocene electrochemistry and host-guest interactions, supporting the development of improved cation sensors with optimised recognition properties, sensitivity, and selectivity. Overall, the work lays the necessary groundwork for applications in analytical chemistry and sensor technologies through customised ferrocene-derived materials.

Light-addressable potentiometric sensor (LAPS) is an electrochemical sensor based on the field-effect principle of semiconductor. It is able to sense the change of Nernst potential on the sensor surface, and the measuring area can be controlled by the illumination. Due to the unique light-addressable ability of LAPS, the chemical imaging system constructed with LAPS can realize the two-dimensional image distribution detection of chemical/biomass. In this paper, the advantages of LAPS as sensing unit of microelectrochemical analysis system are summarized. Then, the greatest development of LAPS analysis system is explained and discussed. Especially, this paper focused on the research of ion diffusion, enzymatic reaction, microbial metabolism and droplet microfluidics by using LAPS analysis system. Finally, the development trends and prospects of LAPS analysis system are illustrated.

Current smartphones incorporate different types of sensors that allow us to know our spatial position, they give us information about pressure, speed, acceleration, time, acoustic level, and other different physical magnitudes. These smartphones measure each component of the magnetic field, bearing in mind that any current perpendicular to a magnetic field produces a small potential difference, transversal to the said current, being this voltage easily measurable by Hall sensors. With the implementation of three Hall sensors, and an appropriate app, we can measure the three components of the magnetic field vector, and with this we can obtain information and deduce properties of the physical systems considered. In this paper we are exploring the use of smartphones in a physics laboratory for freshman students. To do this, we have measured, using Hall sensors, the magnetic field created by a linear quadrature, and we have obtained, first of all, its dependence on the distance between the quadrupole and the magnetic sensor. The second purpose of this work is to show that the laboratory is a powerful tool that increases the significant learning of freshman students through advanced technological tools.

Flow sensing in hostile environment is of increasing interest for applications in automotive, aerospace, and chemical and resource industries. Compared to their counterparts, thermal flow sensors are attractive candidates due to the ease of fabrication, lack of moving parts and higher sensitivity. Recently, a number of thermal flow sensor prototypes have been reported in the literature demonstrating the measurement of fluid flows under hostile conditions. This paper summarizes the concept of thermal flow sensing, operational modes and transduction mechanisms. Then, the choice of materials and their corresponding properties are presented in details. The paper also reports recent progress in the development of thermal flow sensors for harsh environment. In addition, the issues and considerations in packaging are reviewed. Finally, we conclude the review with the future prospects.

The healthcare system is crucial to the development, standard of living, and sustainability of any country. Amid the pandemic, most developed countries are experiencing varying levels of difficulty managing their healthcare systems. Overloading of healthcare services is common, leading to prolonged waiting times for medical services; thus, the wastage of hospital resources must be addressed seriously. In this paper, we examine the problem of no-shows in outpatient clinics. Through a review of the literature and practical industrial experience, we identify the processes of these clinics. We then propose a robust optimisation approach for overbooking using a traditional overbooking model and a robust system. This model aims to mitigate the significant parameter uncertainties encountered during the pandemic. Considering risk aversion, the optimal policy for overbooking can be established while accounting for the costs associated with overbooking. The main contribution of this paper is the introduction of an alternative method to address the uncertainty of no-shows using an overbooking technique.

Artificial Intelligence (AI) in healthcare has ushered in a revolutionary era by transforming the way we provide care and reduce adverse consequences. This paper explores the field of AI applications in healthcare, including side effect management, streamlined administrative procedures, and customized treatment programs.

Due to Motor Neurone Diseases, a large population remains disabled worldwide, negatively impacting their independence and quality of life. This typically involves a weakness in the hand and forearm muscles, making it difficult to perform fine motor tasks such as writing, buttoning a shirt, or gripping objects. This project presents a vision-enabled rehabilitation hand exoskeleton to assist disabled persons in their hand movements. The design goal was to create an accessible tool to help with a simple interface requiring no training. This prototype is built on a commercially available glove where a camera and embedded processor were integrated to help open and close the hand, using air pressure, thus grabbing an object. An accelerometer is also implemented to detect the characteristic hand gesture to release the object when desired. This passive vision-based control differs from active EMG-based designs as it does not require individualized training. Continuing the research will reduce the cost, weight, and power consumption to facilitate mass implementation.

Drones are being used more and more frequently and in various ways to attack people and critical infrastructures, which increases their level of danger and makes early detection and risk assessment even more difficult. There is no ultimate drone sensor. Rather, drones can only be effectively detected, if suitable sensor technologies are integrated within a system. Among the best suited sensorics for this purpose are radar and optical sensors, because the advantage of the radar, given by the long detection range, can be well combined with the additional visual-based information gained from a camera in the mid- and short-range, where usually the radar fails detecting micro drones. In this paper, a modular drone detection and assistance system MODEAS is presented, which can be used to automatically detect and track drones within a range up to some kilometers on the sky, but also in complex urban environments, where buildings and vegetation offer a perfect background for camouflage. The system provides an early detection of flying objects as potential drones, when those are not at all or only as small dots visible for the human eye. Main strengths of the system are the robust AI detection to differentiate such an object against clutter (birds, clouds) and its further classification by model and payload recognition, the latter aspect being considered as an indication of dangerousness. Moreover, once a drone is detected, the system follows it automatically, precisely and smoothly with a high-resolution pan-tilt-camera, measuring the distance to the sensor station with a laser rangefinder, compute the geocoordinates and visualize them live on a map. To improve the precision of the detection, a multisensorial fusion of all sensor detections is performed. Furthermore, alarms may be generated when a drone enters a restricted area.

In recent years, the integration of sensors in agriculture has emerged as a pivotal catalyst for transforming conventional farming practices into precision agriculture. Sensor application is impacting the everyday objects that enhance human life. In this special issue, the main objective was to address recent advantages of sensor application in agriculture covering a wide range of topics in this field. This provides overview of diverse application of sensors in agriculture, highlighting their role in enhancing productivity, sustainability, and resource management. sensors are instrumental in monitoring various agriculture parameter such as soil condition, weather, crop health and livestock wellbeing. By collecting real-time data and providing valuable insight, sensors enable precision farming, optimize resource allocation, and minimize environmental impacts. we have to explore the key sensor types used in agriculture, their applications, benefits, and future prospects, emphasizing their crucial roles in the modernization of agriculture and global quest for food security and crop production.

Sign language recognition is essential in hearing-impaired people’s communication. Sign language recognition is an important concern in computer vision and has been developed with rapid progress in image recognition technology. However, sign language recognition using a general monocular camera has problems with occlusion and recognition accuracy in sign language recognition. In this research, we aim to improve accuracy by using a 2-axis bending sensor as an aid in addition to image recognition. We aim to achieve higher recognition accuracy by acquiring hand keypoint information of sign language actions captured by a monocular RGB camera and adding sensor assist. To improve sign language recognition, we need to propose new AI models. In addition, the amount of dataset is small because it uses the original data set of our laboratory. To learn using sensor data and image data, we used MediaPipe, CNN, and BiLSTM to perform sign language recognition. MediaPipe is a method for estimating the skeleton of the hand and face provided by Google. In addition, CNN is a method that can learn spatial information, and BiLSTM can learn time series data. Combining the CNN and BiLSTM methods yields higher recognition accuracy. We will use these techniques to learn hand skeletal information and sensor data. Additionally, the 2-axis Bending sensor glove data support training AI model. Using these methods, we aim to improve the recognition accuracy of sign language recognition by combining sensor data and hand skeleton data. Our method performed better than using skeletal information, achieving 96.5% accuracy in Top-1.

Polycyclic aromatic hydrocarbons (PAHs) have emerged as promising materials for organic electronics, including organic photovoltaics (OPVs), organic field-effect transistors (OFETs), and organic light-emitting diodes (OLEDs). Particularly, non-hexagonal ring-fused PAHs are highly desirable due to their unique optoelectronic properties. Herein, a new redox-active azulene-perylene diimide triad 1 and its ring-fused counterpart, diazulenocoronene diimide 2, were synthesized and fully characterized by a combination of NMR, cyclic voltammetry, spectroelectrochemistry, and UV-visible absorption spectroscopy. Density functional theory (DFT) and time-dependent DFT (TD-DFT) calculations were performed to gain further insight into various electronic transitions. Interestingly, we found that the adaptive response to acids and bases manifests itself in a reversible two-color-change that can be attributed to changes in the chemical structures.

Novel tetragonal matrix Ba0.5Gd0.5-xNaxF2.5-x, where x = 0.05, doped by Yb3+, Ho3+, Er3+, was synthesized by molten salt synthesis (MSS) from nitrate flux. XRD data show that tetragonal phase with a = 4.122(1) Å, c = 17.672(1) Å is stable in argon atmosphere up to 960 °C. Luminescence spectra recorded in 500-900 nm and 1050-1700 nm upon 974 nm pumping demonstrated the characteristic luminescence at 1550 nm (4I13/2 → 4I15/2) for Er3+ and 1150 nm (5I6 → 5I8) for Ho3+. The relative thermal sensitivity (Sr) at 296-316 K were 0.3 %*K-1 and 5.5%*К-1 in shortwave infrared (SWIR) and visible range, respectively. Synthesized luminophores can be used as dual-range optical temperature sensors, which simultaneously operating in visible and SWIR ranges.

Sensing Technology (ST) plays a key role in Structural Health Monitoring (SHM) systems. ST focuses on developing sensors, sensory systems or smart materials that monitor a wide variety of materials properties aiming to create smart structures and smart materials, using Embedded Sensors (ESs), and allowing continuous and permanent measurements of the structural integrity. The integration of ESs is limited to the processing technology to embed the sensor due to its high-temperature sensitivity and the possibility of damage during its insertion into the structure. In addition, the technological process selection is dependent on the base material composition, either metallic or composite parts. The selection of smart sensors or the technology underlying them is fundamental to the monitoring mode. This paper presents a critical review of the fundaments and applications of sensing technologies for SHM employing ESs, focusing on the actual developments and innovation of these, as well as analysing the challenges that these technologies present, to build a path that allows a connected world through distributed measurement systems.

: This paper presents a couple of meal monitoring systems for senile dementia patients by using electronic weight and temperature sensors. These monitoring systems enable to convey the information of the amount of meal taken by the patients in real-time via wireless communication networks onto the mobile phones of their families or nurses in charge. Thereby, the nurses can easily spot the most desperate patient to take care of while the families can have relief to see the crucial information for survival of their parents at least three times a day. Meanwhile, the senile dementia patients tend to suffer the burn of their tongues because they can hardly recognize the temperature of hot meals served and therefore avoid the burn of tongues. This phenomenon can be discarded by utilizing the meal temperature monitoring system which displays alarm to the patients when the meal temperature is above the reference. These meal monitoring systems can be easily implemented by utilizing low-cost sensor chips and Arduino UNO boards so that elder-care hospitals and nursing homes can afford to exploit them with no additional cost. Hence, we believe that the proposed monitoring systems would be a potential solution to provide a great help and relief not only for the professional nursing nurses working in elder-care hospitals and nursing homes, but also for the families of the dementia patients.

The protection of electronics against environmental influences and mechanical loads is important for integration of conventional electronics in textile conductive tapes. For this purpose, the sensors on the tapes are molded with plastic locally. This process step is recognized in the injection molding process. The molding compound is then later selected depending on: The field of application, the parameters of the manufacturing process and the textile tape properties. We have designed a mould for liquid silicone (LSR) as well as for the textile and electronic insertions. The cavities are sealed by a local compression of the textile and the two inserts are positioned with position pins representing the main aspect of the mould design. The sampling tool and the process parameter optimization are mainly based on the material properties of the silicone and the mechanical sensitivity of the inserts. To reduce the deformation of the circuit boards by the melt front and ensuring the functionality of the electronics a low-pressure process is used.

Climate Change is the most serious planetary emergency of our time. Carbon emissions secondary to the healthcare industry account for about ten percent of all emissions in the United States. Health professionals, therefore, need to understand how they can make a difference in their profession, by understanding the health-related impacts of climate change and the importance of healthcare sustainability. An 8-week telementoring Climate Change Healthcare Sustainability ECHO series was developed to educate healthcare professionals in these topics such as the health-related effects of climate change, healthcare sustainability, quality healthcare and carbon accounting. A total of 376 participants from throughout the US and 16 other countries- completed this 8-week series and received no-cost continuing medical education credits. The evaluation consisted of pre and post Zoom polls, weekly post-session surveys and the registration demographics. Participants were primarily physicians and public health professionals who significantly improved their knowledge and communication skills after the course as compared to starting the training.

Artificial Intelligence (AI) describes computer systems able to perform tasks that normally require human intelligence, such as visual perception, speech recognition, decision-making, and language translation. Examples of AI techniques are machine learning, neural networks and deep learning. AI can be applied in many different areas, such as econometrics, biometry, e-commerce and the automotive industry. In recent years, AI has found its way into healthcare as well, helping doctors to make better decisions (‘clinical decision support’), localizing tumors in magnetic resonance images, reading and analyzing reports written by radiologists and pathologists, and much more. However, AI has one big risk: it can be perceived as a ‘black box’, limiting trust in its reliability, which is a very big issue in an area in which a decision can mean life or death. As a result, the term Explainable Artificial Intelligence (XAI) has been gaining momentum. XAI tries to ensure that AI algorithms (and the resulting decisions) can be understood by humans. In this narrative review, we will have a look at the current status of XAI in healthcare, describe several issues around XAI, and discuss whether it can really help healthcare to advance, for example by increasing understanding and trust. Finally, alternatives to increase trust in AI are discussed, as well as future research possibilities in the area of XAI.

Introduction The prevalence of adolescent electronic cigarette (e-cigarette) use has increased in most countries. This study determines the relation between the frequency of e-cigarette use and the frequency and intensity of cigarette smoking. Furthermore, it evaluates the association between the reasons for e-cigarette use and the frequency of its use. Materials and Methods Participants were 68,043 middle and high school students aged 13–18 years from the 2015 Korean Youth Risk Behavior Web-Based Survey. Of the 68,043 participants, we analyzed 6,655 adolescents with an experience of e-cigarette use. Results The prevalence of ever using and current (past 30 days) use of e-cigarettes was 10.1% and 3.9%, respectively. Of the ever e-cigarette users, approximately 40% used e-cigarettes for ≥1/month and 8.1% used e-cigarettes daily. Daily e-cigarettes users were 10 times greater among daily cigarette smokers than among cigarette users for <1/month (18.1% vs. 1.8%) and 16 times more prevalent among those smoking ≥20 cigarettes/day than among those smoking <1 cigarette/month (38.9% vs. 2.4%). The most common reason for e-cigarette use was curiosity (22.9%), followed by less harmful than conventional cigarettes (18.9%), smoking cessation (13.1%), and indoor use (10.7%). Curiosity was the most common reason among less frequent e-cigarette users; however, smoking cessation and indoor use were the most common reasons among more frequent users. Conclusions Results showed a positive relation between frequency or intensity of conventional cigarette smoking and frequency of e-cigarette use among Korean adolescents, and frequency of e-cigarette use differed according to the reason for the use of e-cigarettes.

Background and purpose: Chronic kidney disease (CKD) is a common chronic disease usually associated with cardiovascular disease (CVD), and premature death and millions of people are at increased risk for CKD. As this disease is extremely complex, multidisciplinary care (MDC) is needed to provide complete and continuous care. Usually, the nephrology units need coopera-tion from several other Healthcare Professionals (HCPs) such as cardiologists, nutritionists, ob-stetricians, and so forth. All modalities of treatments, peritoneal dialysis (PD) and Hemodialysis (HD) require HCPs and patients to develop a variety of skills to effectively deliver and manage dialysis tasks in the center or at home. Information and Communication Technology (ICT) in-terventions can offer tools that provide HCPs and patients with tools that facilitate the manage-ment of kidney patients in centers or at home. ICT interventions can allow to automate registra-tions, videoconferencing, minimize the geographic burden and resource cost savings. ICT can be the best way to promote cost saving on health spending and ensure the sustainability of the health system and, the environment as well. In the Iberian Peninsula, kidney patients consume about 3% of the total cost of healthcare. The cost of kidney transplants and dialysis is around 1.8 billion euros annually, and 75 % of this amount goes to dialysis treatment. Objective: This study aimed to evaluate and analyze the opinion of Healthcare Professionals (HCP) in Nephrology units about the Intervention of ICT in nephrology care and the Clinical benefits results from the use of ICT in Nephrology Services and dialysis Units in Portugal and Spain. Thus we collected the opinion of Health care professionals concerning the role of ICT intervention in nephrology. Understanding HCPs' feelings and attitudes is essential to understand if such technologies are correctly adjusted to the workflow and really bring huge benefits for the clinical practice of nephrology and also what features need improvement and what should be implemented in the future. ICT intervention has been implemented to promote better healthcare in nephrology units and improve patient outcomes. In the Survey, we intended to evaluate nephrology HCPs' opinions concerning the ICT interventions, in nephrology, represented by several tools that al-low the HCPs to implement solutions such as Remote Patient Monitoring(RPM); Remote Moni-toring of Treatment (RMT); Tele homecare; Telehealth (Tele-nephrology); Home Dialysis; mHealth; mobile App; Web Portal, Telemedicine, and so forth. Key Points: In many countries particularly in the Iberian Peninsula (Portugal and Spain) the incidence of CKD is substantially high. The “treatments” for kidney disease have not improved substantially over the past 50 years, leaving too many kidney patients with a poor quality of life and reduced life expectancy. This situation is associated with staggering aggregate annual costs amounting to €140 billion per year in Europe, more than the annual healthcare costs of cancer or diabetes [1]. The increased daily use of information and communication technologies may lead to the need for healthcare professionals to incorporate technology use competencies into practice.

There is a need for strategic healthcare workforce planning to address shortages and ensure universal health coverage, aiming to optimize work-force per population ratio, distribution, and competencies. Amidst rising demands exacerbated by aging populations and events like the COVID-19 pandemic, strategic workforce planning becomes crucial for addressing healthcare inequalities by forecasting needs, bridging skill gaps, and adapting to changing demographics and care models. Israel has invested in strategic planning to tackle healthcare workforce challenges; however, globally there is insufficient planning informed by health labor market analysis, which hinders efforts to address healthcare inequalities. The paper reviews national policies in Israel, Australia, Germany, and Norway, ex-amining statistics and government publications to highlight strategic plan-ning considerations and address challenges in healthcare workforce plan-ning. This paper focuses both on the critical role of physicians in healthcare systems, and on the changing borders between healthcare professions and different national contexts which demand more context dependent strategic workforce planning. We highlight common themes among national policies, including the need for data collection, increasing the capacity of domestic training programs, and the need to address geographic maldistribution of physicians. Ultimately, we aim to guide policy in the development of a re-silient and sustainable healthcare workforce capable of meeting diverse community needs and promoting equity in healthcare services.

Current generation witnesses a huge interest in optical waveguide due to their salient feature such as low cost, immune to electromagnetic interference, easy to multiplex, compact size, etc. These features of the optical fibers makes it an useful tool for various sensing applications including medicine, automotive, biotechnology, food quality control, aerospace, physical and chemical monitoring etc. Among all the reported application, the device has been widely exploited to measure the physical and chemical variation in surrounding environment. Optical fiber based temperature sensor plays a crucial role in this decade to detect high fever and tackle COVID like pandemic. Recognizing the major developments in the field of the optical fibers, this article aims to provide recent progress in temperature sensor utilizing several sensing configuration including standard fiber, photonic crystal fiber, and Bragg grating fibers. Additionally, the article also highlights the advantages, limitations, and future possibilities in this area.

It is since long known, that SAW devices, resonators as well as delay lines, can be used as passive wireless sensors for physical quantities like temperature and pressure as well as gas sensors or ID-Tags. The sensors are robust, work passively without battery, can be applied at high temperatures and provide a high resolution. Nevertheless, if the devices should be readout wirelessly in an industrial environment, several constraints have to be taken into account, especially when more than one quantity or device needs to be measured at the same time. The paper addresses the challenges that have to be tackled when establishing multi-sensor-wireless-readout for industrial applications. Major issues here are the legal ISM-band regulations, as well as sampling time and costs, which impose severe restrictions to any system design. We describe several design approaches and their constraints. We have successfully designed sensors based on reflective delay lines that allow the parallel readout of four independent temperature sensors in the 2.45 GHz ISM-band. These devices have been fabricated, positively tested and demonstrate the applicability of SAW sensors for industrial applications.

Carbon nanotubes have been attracting considerable interest among material scientists, physicists, chemists and engineers for almost 30 years. Owing to their high aspect ratio, coupled with remarkable mechanical, electronic and thermal properties, carbon nanotubes have found application in diverse fields. In this review, we will cover the work on carbon nanotubes used for sensing applications. In particular, we will see examples where carbon nanotubes act as main players in devices sensing biomolecules, gas, light or pressure changes. Furthermore, we will discuss how to improve the performance of carbon nanotube-based sensors after proper modification.

Telemedicine has been increasingly considered an effective strategy to support patients with several diagnosis and therapies, avoiding the on-site visit and drastically reducing the risks to share infections. In the recent years, a number of different technologies have been developed and applied to clinical studies, with the aim to investigate new ways for increase the early diagnoses and monitor the clinical evolution of the most predictable diseases directly from the patients’ home. Telemedicine refers to all those technological interfaces used to remotely perform clinical procedures. Telemedicine applications could be useful in several medical fields, such as preventive medicine, home patient care, education for healthcare professionals and patients, research, public health, and health management. On the other hand, the synergy of these different technologies has a significant impact on the clinical risks analysis, particularly useful in frail patients. Although Telemedicine shows to have important advantages, undoubtedly important issues still remain. The present work aims to shed light on the main advantages and disadvantages related to of each application’s features, which may serve as a useful tool for researchers.

The emergence of blockchain know-how currently presents the opportunity for the health sector to adopt such technologies in electronic health records. Blockchain assists in maintaining and sharing the relevant medical records of the patient with the relevant group of healthcare providers and the hospital. Numerous specific applications include traceability of drug and patient monitoring or Electronic Health Records (EHR). While Blockchain assists in maintaining and sharing the relevant medical records of the patient with the relevant group of healthcare providers and the hospital, it is important to note that the moral consciousness of the healthcare professionals is the main guide of the moral consciousness is ethics. This paper presents an overview of the application of blockchain in the healthcare and medical sector, highlighting the specific challenges and concerns. The study adopted a systematic review of secondary literature in answering the research question.

The fourth industrial revolution, also known as Industry 4.0, has led to an increased transition towards automation and reliance on data-driven innovations and strategies. Companies in the manufacturing sector are heavily integrating Industry 4.0 technologies, including cloud compu-ting, cyber-physical systems (CPS), big data analytics, horizontal and vertical system integration, the internet of things (IoT), and additive manufacturing (3d printing). The interconnected systems and processes have significantly increased operational efficiency, enhanced organizational capacity to monitor and control functions, reduced costs, and improved product quality. One significant way that companies have achieved these benefits is by integrating diverse sensor technologies within these innovations, allowing critical data collection on products, equipment performance, and maintenance. The sensors connect systems and machines, allowing them to communicate and track operations for enhanced operations. While numerous research has been conducted to show the role of sensors in industry 4.0, limited studies show how these innovations can leverage product design to maximize benefits and opportunities. Given the rapidly changing market conditions, Industry 4.0 requires new products and business models to ensure companies adjust to the current and future changes. These requirements call for the evolutions in product design processes to accommodate design features and principles applicable in the current dynamic business environment. This research paper employs a systematic bibliometric literature review (LRSB) methodology to explore and synthesize data on how Industry 4.0 and sensors can leverage product design. The results show that various product design features create opportunities to be leveraged to guarantee the success of Industry 4.0 and sensor technologies. However, the research also identifies numerous challenges that undermine the ongoing transition towards intelligent factories and products.

AbstractBackground: In digitalization era, health care system was conditioned with the health worker’s ability to adapt media of digital technology. Digital technology media was used to strengthening and fasted the health care for patient and community. Aims: This study aimed to explore the accurate information of health professional utilization digital technology during doing the job at the health facilities in Timor-Leste. Methods: This study was used correctional study with 56 respondents was participated in the study. Was collected the data from 1 to 30 February 2023. Was used questioner of google form based for data collection. Data collection was distributed via online with google form to social media as WhatsApp’s, email and face book and twitter to completed by respondents. The inclusive Criteria are: health professional living in Timor-Leste, to able response the questioner. Was used descriptive analysis in this study. Finding: This study was indicated that majority of health professional was participated in the study as 54,2% man then women have 45,8%. About 100% health professional used hand phone to facilitate their daily activities including related with their work activities. Other side indicated in digital technology tools use are able to use Microsoft word is 78,3%, able to use Microsoft Excel is 76,7% and able to use Power Point is 81,7%. E-mail use about 89,2%, WhatsApp’s use 81,7%, About 74,2% was used zoom/webinars/Google meet application, about 72,5% sad that they were used computer in the work place until now. Around 96.4% need to improve or deepen their knowledge and skills in using ICT in the future to facilitate they are activity. Conclusion: Majority of health professional in Timor-Leste was used the computer, internet, hand phone in daily activities. Majority need to gate the training to improve their knowledge, attitude and psychomotor in the future.

Introduction: Substance-induced psychotic disorder (SIPD) is a mental health condition linked to the use of a psychotropic substance whose pathogenesis has not been totally clarified. The present retrospective observational study has the objective to identify differences in clinical features and peripheral biomarkers in SIPD patients according to the main substance of abuse.Methods: A total sample of 218 patients was divided in 3 groups according to the type of consumed substance: alcohol, cannabis and psychostimulants. The 3 groups were compared for continuous variables by one-way analyses of variance (ANOVAs) and for qualitative variables by χ² tests. After removing alcohol-induced psychotic disorder group, the same analyses were repeated. Statistically significant variables from these latter analyses were included in a binary logistic regression model to confirm their reliability as predictors for cannabis- or psychostimulants-induced psychotic disorders. Results: Psychotic cannabis abusers were younger (p<0.01) and had an earlier age at onset (p<0.01). On the contrary, alcohol consumers resulted to have a longer duration of illness (p<0.01), more previous hospitalizations (p=0.04), more frequent medical comorbidity (p<0.01), higher mean Modified Sad Person Scale scores (p<0.01). Finally, psychostimulant abusers had more frequently a lifetime history of poly-substance use disorders (p<0.01). Binary logistic regression revealed that higher mean Brief Psychiatric Rating Scale scores (p<0.01) higher sodium (p=0.012) and haemoglobin(p=0.040) plasma levels were predictors of cannabis misuse in SIPD patients.Conclusions: Different clinical factors and biochemical parameters con be associated to SIPD according to the main substance of abuse, thus requiring a specific management by clinicians.

Today, there are commercially available high-performance electric wheelchairs, capa-ble of responding to strong limitations. However, despite these advancements, there is a significant portion of the population with severe disabilities who cannot access this mobility solution due to safety reasons. Indeed, either due to motor issues preventing reliable control of the wheelchair's commands, or associated visual or cognitive pathologies, the use of an electric wheelchair by these individuals would put them at risk and could also constitute a danger to those around them. This is why our research team is working on the development of augmented wheelchairs that allow a greater autonomy. We are mainly developing a system compatible with all electric wheel-chairs on the market, capable of making them anti-collision and anti-fall on uneven ground (sidewalks, stairs, etc.). In this article, we present our solution regarding the anti-collision function, in particular the sensors used to do this, as well as the strategy. We will focus on the shortcomings and weaknesses of various types of sensors and demonstrate how, by combining them in a certain way, we can develop a collision avoidance device capable of managing the diversity of everyday life situations. The two types of sensors that will be combined here are an in-house developed special near infrared sensor from the laboratory and a commercially available ultrasonic sensor. We will present the internal operation of the sensors, their limitations, experimental tests involving integration with the wheelchair, and the structure of the complete device.

This paper provides a data set collected with an underground shaft mobile mapping system equipped with rotated Velodyne VLP-16, Velodyne Ultra Puck VLP-32c, Livox Tele-15, and IMU Xsens MTi-30. The ground truth data was acquired with a geodetic survey including 15 ground control points and 6 Faro Focus 3D Terrestrial Laser Scanner stations of a total 273,784,932 of 3D measurement points. The aim of the paper is to describe the data set of a mining shaft. Obtained mobile mapping data can be the basis for detailed analyzes of the technical condition of the shaft. This data set provides an end-user case study of realistic applications in mobile mapping technology. It provides ground truth data, mobile mapping data and software tools for manipulation and visualization. The project is released and maintained at https://michalpelka.github.io/mine-mapping-dataset/.

Vehicle safety promises to be one of the Advanced Driver Assistance System (ADAS) biggest benefits. Higher levels of automation remove the human driver from the chain of events that can lead to a crash. Sensors play an influential role in vehicle driving as well as in ADAS by helping the driver to watch the vehicle’s surroundings for safe driving. Thus, the driving load is drastically reduced from steering as well as accelerating and braking for long-term driving. The baseline for the development of future intelligent vehicles relies even more on the fusion of data from surrounding sensors such as Camera, Lidar and Radar. These sensors not only need to perceive in clear weather but also need to detect accurately adverse weather and illumination conditions. Otherwise, a small error could have an incalculable impact on ADAS. As most of the current study is based on indoor or static testing. In order to solve this problem, this paper designs a series of dynamic test cases with the help of outdoor rain and intelligent lightning simulation facilities to make the sensor application scenarios more realistic. As a result, the effect of rainfall and illumination on sensor perception performance is investigated. As speculated, the performance of all automotive sensors is degraded by adverse environmental factors, but their behaviour is not identical. Future work on sensor model development and sensor information fusion should therefore take this into account.

Phenology is one of the ubiquitous fingerprints of climate change on our ecosystems. Monitoring the spatiotemporal patterns of vegetation phenology is thus critical. A wide range of sensors have been used to monitor vegetation phenology. Sensor point of view and resolution can potentially impact estimates of phenology. We compared three different sensors from three different remote sensing platforms—a UAV mounted RGB camera, an under canopy, upward facing hemispherical camera with R, G and NIR capabilities, and a tower mounted RGB PhenoCam—to estimate spring phenological transition in a mixed-species temperate forest in central Virginia, USA. Our study had two objectives: 1) to compare the above- and below- canopy inference of canopy greenness (green chromatic coordinate and normalized difference vegetation index) and canopy structural attributes (leaf area and gap fraction) by matching under-canopy hemispherical photos with high spatial resolution (0.03 m) drone imagery to find the appropriate spatial coverage and resolution for comparison; 2) to compare how each sensor performed in estimating the temporality of the spring phenological transition. We find that a spatial buffer of 20 m radius for UAV imagery is most closely comparable to under-canopy imagery in this system. Sensors and platforms agree within +/- 5 days of when canopy greenness stabilizes from the spring phenophase into the growing season. This work has implications for paring UAV imagery with both tower-based observation platforms, as well as plot-based studies (e.g. long-term monitoring, existing research networks, permanent plots).

Over the last decade, the prevalence of health issues has increased by approximately 29.1%, putting a substantial strain on healthcare services. This has accelerated the integration of machine learning in healthcare, particularly following the COVID-19 pandemic. The utilization of machine learning in healthcare has grown significantly, however many present approaches are unsuitable for real-world implementation due to high memory footprints and lack of interpretability. We introduce DeClEx, a pipeline designed to address these issues. DeClEx ensures that data mirrors real-world settings by incorporating gaussian noise and blur and employing autoencoders to learn intermediate feature representations. Subsequently, our convolutional neural network, paired with spatial attention, provides comparable accuracy to state of the art pre-trained models while achieving threefold improvement in training speed. Furthermore, we provide interpretable results using explainable AI techniques. We integrate denoising and deblurring, classification and explainability in a single pipeline called DeClEx.

Management of a healthcare unit demands high prerequisites. It is a challenging organizational job for the healthcare decision-makers or leaders to tackle biomedical threats and deliver care service to huge number of affected populations in different demographic area. Health administration take innovative strategies to provide fundamental and life-saving services to the patients, when keeping the safety of the frontline medical workers is undoubtedly a priority. COVID-19 pandemic has changed the overall functioning of the healthcare system globally with alteration in the health decision-making protocols. Through this article, I have elucidated the challenges of healthcare along with today’s managerial paradigms to tackle the problems and run the system in a regulated manner.

Considering the multifaceted nature of neurodegenerative diseases like dementia and the neces-sity for interprofessional knowledge, this research extends its scope to encompass professionals with diverse levels of training and experience in dementia care. A need analysis for the project “My INdividual Digital EDucation.RUHR” (MINDED.RUHR) is conducted to develop an au-tomatized recommender system for individual learning content using AI. In this sub-study, the aim was to reveal didactic specialties, knowledge gaps and structural challenges of further edu-cation in dementia care of different health professions and to derive learning preference personae. Eight focus group interviews among nine health professions and up to six participants (n = 34) each took place to survey distinct didactic experiences and learning needs. The results reflect various learning preferences, with a propensity to multimedia, practical and interactive tasks. Health professions are used to digital education but show aversions against certain e-learning formats. The derived learning preference personae constitute profound blueprints for a us-er-centred digital education design process, aiming to establish personalized and representative further education in dementia care applicable to various individual preferences and structural workplace challenges of healthcare professions.

Academics in healthcare grapple with the challenge of efficiently managing time while addressing diverse roles and responsibilities, leading to heightened levels of anxiety and stress within the academic community. The primary objective of this study is to offer a sustainable and systemic solution to the prevalent time-management challenges in healthcare academia, through the development of a predictive model. Employing systemic analysis software and adopting a systemic management approach, we crafted a model to address academic time-management concerns. The dynamics of time allocation for academicians are governed by three fundamental pillars: teaching, research, and administrative tasks. Significantly prioritizing administrative tasks depletes valuable academic time, making time management within academia excessively costly. This occurs as highly skilled individuals find themselves diverted towards administrative duties at the expense of their academic roles diminishing resilience levels. The proposed Timebooster Academic Systemic Model (TASM) advocates for the cultivation of soft skills in academia, en-compassing prioritization, seeking assistance, and addressing tendencies of perfectionism and procrastination. Additionally, TASM recommends the implementation of full automation, delegation of administrative responsibilities, and the mitigation of both overt and covert time-consuming elements. Furthermore, TASM reports on the pivotal role of the academic resilient manager-leaders, who actively contribute to their own satisfaction and academic growth by enhancing collaboration and teamwork. Time-management challenges emerge as a critical determinant of academic well-being and resilience. Systemic models, exemplified by TASM, offer a valuable framework for investigating prioritization concerns, identifying administrative impediments in academic processes, and managing low-value time-consuming elements. The TASM model, along with the systemic philosophy underpinning its design, presents an avenue for advancing the exploration of time-management phenomena within the context of healthcare academia.

In this research, we investigate the healthcare expenditure patterns in Uzbekistan, analyze their economic implications, and provide policy recommendations. The study focuses on the time frame from 2000 to 2019, employing quantitative data analysis, theoretical frameworks such as Wagner’s Law, and an economic geography perspective. Our objective is to gain insights into the relationship between economic development and healthcare spending, identify spatial disparities, and forecast future trends. The findings reveal fluctuations in per capita healthcare spending, emphasizing the necessity for sustainable financing mechanisms and preventive measures. Ultimately, our study underscores the significance of aligning healthcare expenditure decisions with economic objectives while prioritizing the well-being of the population.

The COVID-19 crisis has brought unprecedented strain on healthcare systems around the world. It has perhaps taught us some key lessons that are worth considering and addressing to help build more sustainable health systems as well as improve our ability to combat future epidemics.

This paper provides an overview of flexible and wearable respiration sensors with emphasis on their significance in healthcare applications. The paper classifies these sensors based on their operating frequency distinguishing between high-frequency sensors which operate above 10 MHz and low-frequency sensors. The operating principles of breathing sensors as well as the materials and fabrication techniques employed in their design are addressed. The research highlights the need for robust and flexible materials to enable the development of reliable and comfortable sensors. Finally, the paper presents potential research directions and proposes research challenges in the field of flexible and wearable respiration sensors. Thus, identifying emerging trends and gaps in knowledge, it encourages further advancements and innovation in the rapidly evolving domain of flexible and wearable sensors.

Palpation is a simple but effective method to differentiate tumors from healthy tissues. Development of miniaturized tactile sensors embedded on endoscopic or robotic devices are the key toward precise palpation diagnosis and the subsequent timely treatment. This paper reports on the fabrication and characterization of a novel tactile sensor with mechanical flexibility and optical transparency that can be easily mounted on soft surgical endoscopes and robotics. Utilizing the pneumatic sensing mechanism, the sensor offers a high sensitivity of 1.25 mbar and negligible hysteresis, enabling the detection of phantom tissues with different stiffnesses ranging from 0 to 2.5 MPa. Our configuration combining pneumatic sensing and hydraulic actuating also eliminates electrical wiring from the functional elements located at the robot end-effector, thereby enhancing the system safety. The optical transparency path in the sensors together with its mechanical sensing capability open interesting possibility in early detection of solid tumor as well as in the development of all in-one soft surgical robots that can perform visual/mechanical feedback and optical therapy.

Temperature measurements are of great importance in many fields of human activities, including industry, technology, and science. For example, obtaining a certain temperature value or a sudden change in it can be the primary control marker of a chemical process. Fiber optic sensors have remarkable properties giving a broad range of applications. They enable continuous real-time temperature control in difficult-to-reach areas, in hazardous working environments (air pollution, chemical or ionizing contamination), and the presence of electromagnetic disturbances. The use of fiber optic temperature sensors in polymer technology can significantly reduce the cost of their production. Moreover, the installation process and usage would be simplified. As a result, these types of sensors would becoming increasingly popular in industrial solutions. This review provides a critical overview of the latest development of fiber optic temperature sensors based on Fabry-Perot interferometer made with polymer technology.

Since 1970s, a great deal of attention has been paid to the development of semiconductor–based biosensors because of the numerous advantages they offer, including high sensitivity, faster response time, miniaturization, and low–cost manufacturing for quick biospecific analysis with reusable features. Commercial biosensors have become highly desirable in the fields of medicine, food, environmental monitoring as well as military applications (e.g., Hoffmann–La Roche, Abbott Point of Care, Orion High technologies, etc.), whereas increasing concerns on the food safety and health issues have resulted in the introduction of novel legislative standards for these sensors. Numerous devices have been developed for monitoring of biological–processes such as nucleic–acid hybridization, protein–protein interaction, antigen–antibody bonds and substrate–enzyme reactions, just to name a few. Since 1980s scientific interest moved to the development of semiconductor–based devices which also include integrated front–end electronics, such as the extended–gate–field–effect–transistor biosensor which is one of the first miniaturized chemical sensors. This work is intended to be a review of the state of the art focused on the development of biosensors based extended–gate–field–effect–transistor within the field of bioanalytical applications, which will highlight the most recent research works reported in the literature. Moreover, a comparison among the diverse EGFET devices will be presented giving particular attention to the materials and technologies.

We address Multi-Wall Carbon NanoTubes (MWCNTs) for structural health monitoring in adhesive bonds such as in building structures. MWCNT-loaded composites are employed to sense strain changes under tension load using an AC impedance measurement setup. Different weight percentages of 1, 1.5, 2 and 3 wt.% MWCNT are added to the base epoxy resin using different dispersion times, i.e. 5, 10 and 15 minutes. The equivalent parallel resistance of the specimens is measured by applying an alternating voltage at different frequencies. To determine the mechanical as well as sensory properties, the specimens are subjected to a tensile test with concurrent impedance measurement. Using alternating voltage, a higher sensitivity of the impedance reading can be achieved. Employing these sensors in buildings and combining the readings of a network of such devices can significantly improve the buildings’ safety. Additionally, networks of such sensors can be used to identify necessary maintenance actions and locations.

Promoter is a small region of DNA sequence in response to various transcription factors, which initiates a particular gene expression. The promoter-engineered bio-sensor can activate or repress gene expression through transcription factor recognizing specific molecules, such as polyamine, sugars, lactams, amino acids, organic acids or redox molecule, however, the reported applications of promoter enhanced bio-sensor are not too much. This review paper highlights the strategies of construction of promoter-gene engineered bio-sensor with human and bacteria’s genetic promoter array for high-throughput screening (HTS) molecular drugs, study of membrane protein’s localization and nucleocytoplasmic shuttling mechanism of regulating factor, enzyme activity, detection of the toxicity of intermediate chemicals, and probing bacteria density to improve value-added product titer. These bio-sensors’s sensitivity and specificity can be further improved by proposed approaches of Mn²⁺ and Mg²⁺ added random Error-prone PCR and site-directed mutagenesis which is applied for construction of bacteria’s “mutant library”. It is expected to establish flexible HTS platform (Bio-sensor array) to large-scale screen transcription factor-acting drugs, reducing the toxicity of intermediate compounds, and constructing gene dynamic regulatory system in “push and pull” mode to effectively regulate the valuable medicinal product production. This proposed novel promoter-engineered biosensors aided synthetic genetic circuit construction will maximize the efficiency of bio-synthesis of medicinal compound, which will greatly promote the development of microbial metabolic engineering and biomedical science.

Smart sensors based on graphene field effect transistor and biologically receptors are regarded as a promising nanomaterial that could be the basis for future generations of selective real-time monitoring of target analytes and smaller electronics. So the purpose of this paper is to provide details a real-time and selective explosive sensor based on GFETs and PDA-based lipid membranes coupled with biologically inspired TNT peptide receptors. Following an introduction, this paper describes the way of fabrication of the GFETs device by investigation methods for transferring graphene sheet from Cu substrates to target substrates, which is functionalized by the TNT peptide receptors, in order to offer a system which has the capability of answering the presence of related target molecules. Field effet transistor was fabricated using graphene as a channel and monitored by the source-drain current and back-gate voltage curves in the measurement. The transport property changed compared to that of the FET made by intrinsic graphene, that is, the Dirac point position moved from positive Vg to negative Vg, indicating the transition of graphene from p-type to n-type after annealing in TNT, and GFET sensor show good sensitivity and selectivity response.