The oscillating heat pipe (OHP) is a new member in the family of heat pipes, and it has great potential applications in energy conservation. However, the fluid flow and heat transfer in the OHP as well as the fundamental effects of inner diameter on them have not been fully understood, which are essential to the design and optimization of the OHP in real applications. Therefore, by combining the high-speed visualization method and infrared thermal imaging technique, the fluid flow and thermal performance in the OHPs with inner diameters of 1, 2 and 3 mm are presented and analyzed. The results indicate that three fluid flow motions, including small oscillation, bulk oscillation and circulation, coexist or, respectively, exist alone with the increasing heating load under different inner diameters, with three flow patterns occurring in the OHPs, viz. bubbly flow, slug flow and annular flow. These fluid flow motions are closely correlated with the heat and mass transfer performance in the OHPs, which can be reflected by the characteristics of infrared thermal images of condensers. The decrease in the inner diameter increases the frictional flow resistance and capillary instability while restricting the nucleate boiling in OHPs, which leads to a smaller proportion of bubbly flow, a larger proportion of short slug flow, a poorer thermal performance, and easier dry-out of working fluid. In addition, when compared with the 2 mm OHP, the increasing role of gravity induces the thermosyphon effect and weakens the 'bubble pumping' action, which results in a little smaller and bigger thermal resistances of 3 mm OHP under small and bulk oscillation of working fluid, respectively.

The Double U-pipe ground heat exchanger, recognized for its straightforward process, cost-effectiveness, high heat exchange efficiency, and low thermal resistance, stands as the predominant ground heat exchanger type in today's shallow geothermal energy development and utilization. Recent years have seen significant research into the heat transfer influencing factors and heat exchange performance of Double U-pipe ground heat ex-changers via experimental testing methods. Yet, studies integrating numerical simulation with in-situ testing have been less frequent. Drawing on the cylindrical heat source model theory and the outcomes of regional in-situ thermal response tests, this paper develops a Double U-pipe ground heat transfer model by establishing physical, mathematical, and heat transfer geometric models. It assesses the impact of varying inlet temperatures, flow rates, and initial ground temperatures on heat exchange efficiency under heating conditions. The results validate the precision of the double U-pipe ground heat exchanger model based on in-situ testing. They show that enhancing the temperature differential between the inlet and initial temperatures, elevating the initial ground temperature, and moderately increasing the flow rate can boost the system's heat exchange efficiency.

The new unique technology for granulation of metals and nonmetallic melts is presented in the paper. It was created on the newly developed controlled film flow disintegration with rapid cooling of the droplets and solidified granules in amorphous state. Three new phenomena discovered by us created the base for 3 different methods for granulation of metals and nonmetallic melts in a wide range of granules’ sizes. Electromagnetic resonance method allows producing granules of metals in the range of 1 mm and over. The soliton-like vibrational regime is available for production of any granulation material in the range 0.1-1 mm. Moreover, the shockwave regime is applicable for producing particles from 10 micrometers by size. All methods produce particles of the stated size with a narrow distribution by size: deviation from the average size no more than 50%. The other known methods do not produce granules with such high cooling rate, which can realize the amorphous state and cannot regulate size of particles in such bright but narrow range from 10 micrometers to 1-2 mm.

The most important plastic resins used for wire coating are Polyvinyl Chloride (PVC), Nylon, Polysulfone and Low-high density polyethylene (LDPE / HDPE). In this article,the coating process is performed using elastic-viscous fluid as a coating material for wire coating in a pressure type coating die. The elastic-viscous fluid is electrically conducted in the presence of an applied magnetic field. The governing non-linear equations are modeled and then solved analytically by utilizing an Adomian decomposition method (ADM). The convergence of the series solution is established. The results are also verified by Optimal Homotopy Asymptotic Method (OHAM). The effect of different emerging parameters such as non-Newtonian parameters α and β, magnetic parameter M and the Brinkman number Br on solutions (velocity and temperature profiles) are discussed through several graphs. Additionally, the current result also compares with the published work already available in the literature.

Due to environmental concerns, natural refrigerants and their use in refrigeration and air conditioning systems are receiving more attention from manufacturers, end users and the scientific community. The study of heat transfer and pressure drop is essential for accurate design and more energy efficient cycles using natural refrigerants. The aim of this work is to provide an overview of the latest outcomes related to heat transfer and pressure drop correlations for ammonia, propane, isobutane and propylene and to investigate the current state of the art in terms of operating conditions. Available data on the existing correlations of heat transfer coefficient and pressure drop for natural refrigerants have been collected through a systematic search. Whenever possible, validity intervals are given for each correlation and the error is quantified. It is the intention of the authors that this could be a valuable support for researchers and an aid to design, with particular reference to heat pumps. A procedure based on the Preferred Reporting Items for Systematic Reviews and Meta-Analyses (PRISMA) statement was adopted, and the Scopus database was used to query the relevant literature. A total of 135 publications qualified for inclusion in the survey; 34 articles report experimental investigations for not usual geometric conditions. Of the 101 selected papers related to usual geometric conditions, N = 50 deal only with HTC, N = 16 deal only with pressure drop and the remainder (N = 35) analyse both HTC and pressure drop. Among the 85 HTC papers (N = 53) deal with the evaporating condition, N = 30 with condensation and only N = 2 with the heat transfer correlations under both conditions. Most of the 101 articles concern propane and isobutane. The high temperatures are less widely investigated.

The plate fin heat exchanger is the compact heat exchanger applied in many industries because of its high thermal performance. To enhance the heat transfer of plate fin heat exchanger in further, three new kinds of wavy plate fins, namely perforated wavy fin, staggered wavy fin and discontinuous wavy fin are proposed and investigated by CFD simulations. The effects of key design parameters, including that of waviness aspect ratios, perforation diameters, stagger ratios and breaking distance are investigated, respectively, with the Reynolds number changes from 500 to 4500. It is found that due to the swirl flow and efficient mixing of fluid, the perforation, serration and breaking techniques are beneficial for the enhancement of heat transfer compared to the traditional wavy fin. At the same time, serration is beneficial to reduce the friction factor, and the breaking technique can reduce heat transfer area as well as enhance heat transfer performance. Through the performance evaluation criteria, the staggered wavy fin has an advantage over the small waviness aspect ratio compared to the perforated wavy fin. The maximum performance evaluation criteria (PEC), as high as 1.24, can be obtained for the perforated wavy fin at the largest waviness aspect ratio.

In this research, a novel method to investigation the transient heat transfer coefficient in a channel is suggested experimentally, in which the water flow, itself, is considered both just liquid phase and liquid-vapor phase. The experiments were designed to predict the temporal and spatial resolution of Nusselt number. The inverse technique method is non-intrusive, in which time history of temperature is measured, using some thermocouples within the wall to provide input data for the inverse algorithm. The conjugate gradient method is used mostly as an inverse method. The temporal and spatial changes of heat flux, Nusselt number, vapor quality, convection number, and boiling number have all been estimated, showing that the estimated local Nusselt numbers of flow for without and with phase change are close to those predicted from the correlations of Churchill and Ozoe (1973) and Kandlikar (1990), respectively. This study suggests that the extended inverse technique can be successfully utilized to calculate the local time-dependent heat transfer coefficient of boiling flow.

The objective of this work is to analyze the improvement of heat transfer in trapezoidal fin heat exchangers using numerical simulation. Heat exchangers are essential components frequently used in contemporary electronic gadgets to effectively disperse heat produced by high-power components. Nevertheless, as electronic devices continue to advance and become more powerful, the heat transfer capacity of heat exchangers is facing more requirements, therefore requiring enhanced heat dissipation efficiency. Afterwards, various fin angles were adjusted, and the heat transmission efficiency was compared. Modifying the angles can significantly improve the effi-ciency of convective heat dissipation. Moreover, it has been found that employing an optimized trapezoidal fin structure can further enhance the efficiency of heat transfer. The results indicate that trapezoidal fin heat exchangers provide superior heat dissipation efficiency compared to conventional heat exchangers. This is important for enhancing the thermal dissipation capabili-ties of electrical gadgets, hence guaranteeing steady functionality and extending their longevity. Subsequent study might explore supplementary methods to boost heat transmission in different heat exchanger configurations in order to meet the growing requirements for heat dissipation.

A sintered wick was formed in a heat pipe through the process of sintering a mixture of copper powder with particle sizes of 100㎛ and 200㎛, mixed with a pore-forming agent. On application to the heat pipes. The thermal resistance of heat pipes containing a sintered wick was calculated for different tilting angles (0°, 45°, and 90°) according to the type of powder, thickness of the sintered wick, and the filling ratio of the working fluid. The heat transfer efficiencies were evaluated through temperature tests. The capillary force, which is closely related to heat transfer efficiency, is determined by the effective pore radius resulting from the sintering of the copper powder. Furthermore, it was observed that the heat transfer performance of the heat pipe was at its best when the working fluid filling ratio was 30%. Additionally, the width of the wick was found to have a direct correlation with the heat transfer performance.

This study presents the comparison of heat transfer capacity and pressure drop characteristics between a basic fin-tube heat exchanger and a modified heat exchanger with the structural change of branch tubes and coiled turbulators. All experiments were carried out using an air-enthalpy type calorimeter based on the method described in ASHRAE standards, under heat exchanger experimental conditions. 14 different kinds of heat exchangers were used for the experiment. Cooling and heating capacities of the turbulator heat exchanger were excellent, compared to the basic one. As the insertion ratio of the coiled turbulator and the number of row increased, the heat transfer performance increased. However, the capacity per unit area was more effective in 4 rows than 6 rows, and the cooling performance of the 6 row turbulator heat exchanger (100% turbulator insert ratio) was down to about 6% than that of 4 row one. As the water flow rate and the turbulator insertion ratio increased, the pressure drop of the water side increased. This trend was more pronounced in 6 rows. In the cooling condition, the pressure drop on the air side was slightly increased due to the generation of condensed water, but was insignificant under the heating condition. The power consumption of the pump was more affected by the water flow rate than the coiled turbulator. The equivalent hydraulic diameter of a tube by the turbulator was reduced and then the heat transfer performance was improved. Thus, the tube diameter was smaller, the heat flux was better.

Introduction: Heat is a kinetic process whereby energy flows from between two systems; hot-to-cold objects. In oro-dental implantology, conductive heat transfer/(or thermal stress) is a complex physical phenomenon to analyze and consider in treatment planning. Hence, ample research has attempted to measure heat-production to avoid over-heating during bone-cutting and -drilling for titanium (Ti) implant-site preparation and insertion, thereby preventing/minimizing early (as well as delayed) implant-related complications and failure. Objective: Given the low bone-thermal conductivity whereby heat generated by osteotomies is not effectively dissipated and tends to remain within the surrounding tissue (peri-implant), increasing the possibility of thermal-injury; this work attempts to obtain an exact analytical solution of the heat equation under exponential thermal-stress, modeling transient heat transfer and temperature changes in Ti implants upon hot-liquid intake. Materials and Methods: We investigate the impact of the material, the location point along implant length, and the exposure time of the thermal load on temperature changes. Results: Despite its simplicity, the presented solution contains all the physics and reproduces the key features obtained in previous numerical analyses studies. To the best of knowledge, this is the first introduction of the intrinsic time, a “proper” time that characterizes the geometry of the dental implant, where we show, mathematically and graphically, how the interplay between “proper” time and exposure time influences temperature changes in Ti implants, under the suitable initial and boundary conditions. Conclusions: This work aspires to accurately complement the overall clinical diagnostic and treatment plan for enhanced bone-implant interface, implant stability and success rates, whether for immediate or delayed loading strategies.

The design complexity of the new generation of civil aero-engines results in higher demands on engines’ components, higher component temperature, higher heat generation, and, finally, critical thermal management issues. This paper will propose a methodological approach to create physics-based models for heat loads developed by sources as well as a systematic sensitivity analysis to identify the effects of design parameters on the thermal behaviour of civil aero-engines. The ranges and levels of heat loads generated by heat sources (e.g., accessory gearbox, bearing, pumps, etc.) and heat absorption capacity of heat sinks (e.g., engine fuel, oil, and air) are discussed systematically. The practical research challenges for thermal management system design and development for the new and next generation of turbofan engines will then be addressed through a sensitivity analysis of the heat load values as well as the heat sinks flow rates. The potential solutions for thermal performance enhancements of propulsion systems will be proposed and discussed accordingly.

Demand for development of the convergence industry, research studies on electrical conductivity, thermal characteristics, semiconductors, motors, and batteries using special materials have come to the fore. Meanwhile, molybdenum (Mo) exhibits relatively small inorganic qualities, and the thermal conductivity rate is applied to various fields. In this study, in-depth characteristics were considered regarding the concentration of thermal characteristics, IR car terminal characteristics, and IR ve-hicles. This study calculated each phase temperature of the molybdenum sputtered specimens in the steady state according to the heat transfer theory. When the molybdenum-sputtered fabric’s metal layer pointed to the outside air, the heat transfer rate (Q) was high at 5748.3W, In contrast, if the molybdenum sputtered film’s metal layer of the pointed toward the heat source, the heat transfer rate (Q) was low at 187.1W. As a result of measuring the IR transmittance, the infrared transmit-tance of the molybdenum sputtering-treated sample was significantly reduced compared to the untreated sample. In the case of untreated samples, the transmittance ranged from 92.7 to 42.0%. When only the cross part was treated with molybdenum sputtering and the molybdenum surface was directed toward the IR irradiator, the IR transmittance was 66.8~0.7%. It is believed that the molybdenum sputtering polyamide samples produced in this study can be applied to multifunc-tional military wear, biosignal detection sensors, semiconductor products, batteries, etc., by utilizing excellent electrical properties, stealth functions, IR blocking properties, and lightness for infrared thermal imaging detectors.

Heat transfer enhancement and hydrodynamic characteristics of nanofluid use in a micro heat exchanger is investigated for cooling electronic components working in hot climatic conditions. The cooling fluid employed was water and TiO2 nanoparticles at concentrations of 1% and 5%, Reynolds numbers ranged from 400 to 2000, and inlet temperatures ranged between 35ºC and 65ºC. At a nanofluid inlet temperature of 55ºC and a nanoparticle concentration of 1%, the Nusselt number increased by 23% up to 54% as the Reynolds number varied between 400 and 2000. At a nanoparticle concentration of 5%, the percentages which correspondingly enhanced the Nusselt number were 32% and 63%. The temperature of the electronic heating component decreased by 4.6-5.2ºC when the nanofluid concentration was increased from 0 to 5% at a Reynolds number of 400 and a nanofluid inlet temperature of 35ºC. Small increments in pressure drop of about 6% and 13% were observed at nanofluid concentrations of 1% and 5%, respectively. With nanoparticle concentrations of 1% and 5%, a Reynolds number of 2000 and a nanofluid inlet temperature of 35ºC, performance evaluation criterion (PEC) values of 1.36 and 1.45 were obtained. When the nanofluid inlet temperature was increased to 65ºC, the PEC parameter decreased to 1.02-1.10 for both concentrations.

This study mainly experimentally investigates and explores the effects of local low-frequency vibrations on the starting-up and heat transfer characteristics of the pulsating heat pipe. A micro motors with the vibration frequency of 200 Hz were imposed on the external surface of evaporation, condensation and adiabatic section of the pulsating heat pipe, respectively, and the starting-up temperature and the average temperatures along the evaporation section as well as the thermal performances of the vibrating heat pipe were experimentally scrutinized under the local vibrations of different positions. The following important conclusions can be achieved by the experimental study: 1) The effect of vibrations at the evaporation section and at the adiabatic section on the starting-up time of pulsating heat pipe is more significant than that at the condensation section. 2) The vibrations at different positions can reduce the starting-up temperature of the pulsating heat pipe. The effect of the vibrations at the evaporation section is the best as the heating power is lower, and the effect of the vibration at the adiabatic section is the best as the heating power is higher. 3) The vibrations at the evaporation section and at the adiabatic section can reduce the thermal resistance of the pulsating heat pipe. However, the vibrations at the condensation section have little effect on the thermal resistance of the pulsating heat pipe. 4) The vibrations at the evaporation section and at the adiabatic section can effectively reduce the temperature of evaporation section of the pulsating heat pipe, but the vibrations at the condensation section have no effect on the temperature of evaporation section of the pulsating heat pipe.

Chemical vapor deposition (CVD) is a vital process for depositing thin films of various materials with precise control over thickness, composition, and properties. Understanding the heat and mass transfer mechanisms during CVD is essential for optimizing process parameters and ensuring high-quality film deposition. This review provides an overview of recent advancements in the heat and mass transfer modeling for chemical vapor deposition processes. It explores innovative modeling techniques, recent research findings, emerging applications, and challenges in the field. Additionally, it discusses future directions and potential areas for further advancement in CVD modeling.

Two-dimensional heat diffusion problem with heat source which is quasilinear parabolic problem is examined analytically and numerically. Periodic boundary conditions are used as a boundary conditions. Since the problem is not linear, Picard’s successive approximation theorem is used. Under certain conditions of natural regularity and consistency imposed on the input data, establish the existence, uniqueness and constant dependence of the solution on the data using the generalized Fourier method. As a numerical solution, implicit finite difference scheme is used. The results ob-tained from analytical and the numerical solutions are so close to each other.

New analytical solutions of the heat conduction equation are presented in cylindrical and spherical coordinates. Then these solutions are reproduced with high accuracy by recent explicit and unconditionally stable finite difference methods. After this, real experimental data from the literature regarding a heated cylinder are reproduced by the explicit numerical methods as well as by Finite Element Methods (FEM) ANSYS workbench. Convection and nonlinear radiation are also considered on the boundary of the cylinder, and it is shown that the explicit methods are much more accurate than the commercial software.

As a new kind of highly compact and efficient micro-channel heat exchanger, printed circuit heat exchanger (PCHE) is a promising candidate satisfying the heat exchange requirements of liquefied natural gas (LNG) vaporization at low and high pressure. The effects of airfoil fin arrangement on heat transfer an flow resistance were numerically investigated using supercritical liquefied natural gas (LNG) as a working fluid. The thermal properties of supercritical LNG were tested by utilizing a REFPROF software database. Numerical simulation was performed using FLUENT. The inlet temperature of supercritical LNG was 121 K,and its pressure was 10.5MPa. The reference mass flow rate of LNG was set 1.22 g/s for the vertical pitch L_v = 1.67 mm and the staggered pitch L_s = 0 mm, with the Reynolds number of about 3750. The SST k-ω model with enhanced wall treatment was selected by comparing with the experimental data. The airfoil fin PCHE had better thermal-hydraulic performance than that of the straight channel PCHE. Moreover, the airfoil fins with staggered arrangement displayed better thermal performance than that of the fins with parallel arrangement. The thermal-hydraulic performance of airfoil fin PCHE was improved with increasing L_s and L_v. Moreover, L_v affected on the Nusselt number and pressure drop of airfoil fin PCHE more obviously. In conclusion, a sparser staggered arrangement of fins showed a better thermal-hydraulic performance in airfoil fin PCHE.

A non-Newtonian fluid model is used to investigate the two-dimensional pulsatile blood flow through a tapered artery with a stenosis. The mixed convection effects of heat and mass transfer are also taken into account. By applying non-dimensionalization and radial coordinate transformation, we simplify the system in a tube. Under the finite difference scheme, numerical solutions are calculated for velocity, temperature concentration, resistance, impedance, wall shear stress and shearing stress at the stenosis throat. Finally, Quantitative analysis is carried out.

The shape memory alloys belong to the smart materials thanks to their thermomechanical proprieties' reply to thermal or to mechanical loading. These materials can change shape, stiffness, displacement, natural frequency, and many mechanical characteristics in response to stress or to heat such as conduction, convection or radiation. However, heating by convection or conduction are the most useful and studied methods unlike radiation. Therefore, this paper aims to study the radiation effect on the shape memory alloy behavior

Higher order femtoscopy measured to examine the heat exchanger characterization of the fluid debris produced in the collisions and investigated a remarkable suppression in the bosons interferences measurement. The analogous suppression can be analyzed to explore the coherence of boson thermal particle production sources at unprecedented energies. We illustrate the particles emissions from radiated sources with statistical coherence which induce the thermal particles interferences to probe the peculiarity of the heated sources as well as the distinctions about the heat exchangers in the collisions at higher temperature. We perspicacious that the bosons seem to the pertinent aspirant of heat exchanger, and the normalized three particles correlators evaluate the existence of such hybrid phases significantly. The key point of this research is that we analyze the three particles correlations with their normalized correlations by difference equations to determine the characteristics of heat exchanger and its applications. With such distinctive and efficient approach, we observe a significant difference in the correlation functions at higher temperature and momenta regimes.

Hydrothermal /super critical processes are important process to synthesize materials which are otherwise difficult to form under normal conditions. A mathematical model is developed using standard transport equations to calculate the time for heating of hydrothermal reactor and computer simulation of the model was carried out in SOLIDWORKS® to validate it. The materials used to form reactor vessel were stainless steel (outer body) and TEFLON (PFA) (inner vessel). It was shown that composite wall, its geometry, construction & properties greatly affect the time and pattern of heat transfer. The time calculated and pattern generated were found to be in good agreement with experimental values.

The heat and matter transfer during glucose catabolism in living systems and their relation with entropy production are a challenging subject of the classical thermodynamics applied to biology. In this respect, an analogy between mechanics and thermodynamics has been performed via the definition of the entropy density acceleration expressed by the time derivative of the rate of entropy density and related to heat and matter transfer in minimum living systems. Cells are regarded as open thermodynamic systems that exchange heat and matter resulting from irreversible processes with the intercellular environment. Prigogine’s minimum energy dissipation principle is reformulated using the notion of entropy density acceleration applied to glucose catabolism. It is shown that, for out-of-equilibrium states, the calculated entropy density acceleration is finite and negative and approaches as a function of time a zero value at global thermodynamic equilibrium for heat and matter transfer independently of the cell type and the metabolic pathway. These results could be important for a deeper understanding of entropy generation and its correlation with heat transfer in cell biology with special regard to glucose catabolism representing the prototype of irreversible reactions and a crucial metabolic pathway in stem cells and cancer stem cells.

The exact determination of radiative exchanges between solids and surfaces has been a long sought-for question in heat transfer science. Being the canonical equation that rules such phenomena, a fourfold integral, it is extremely difficult to obtain an accurate solution like a formula or abacus. Over the last thirty years, the author has tried to integrate the canonical expression by sundry procedures and they have published two books and a dozen of articles on the matter, recently by virtue of computational geometry and graphic algorithms as a new way to solve the finite-difference problems that arise on complex geometries. In architectural engineering curved radiant emitters are customary since antiquity, especially in domes and vaults and their oculus, However, a consistent procedure to handle them was not readily available. The principles that are described hereby based on Cabeza-Lainez’ first principle for spherical fragments offer a complete panorama on the manner in which surface sources related or contained in spheres can be interpreted and accounted for without resorting to integration. The main advance is that a variety of unexplained problems of radiative heat transfer, applicable to aerospace engineering, meteorological, architectural and medical sciences can be sorted out as exactly as quickly.

This paper studied the natural convection heat transfer from two equal-sized cylinders of triangular cross-section confined in triangular enclosure. The inner cylinders have hot surfaces and the outer enclosure has a cold surfaces. The annular space between inner cylinders and the outer one was filled with incompressible Newtonian fluid. The work examined the behavior of fluid flow in the process of transferring heat energy. The work was achieved numerically using the commercial code ANSYS-CFX. The adopted initial conditions were selected for these ranges: Prantl number (Pr = 1 to 10³), Rayleigh number (Ra = 10³ to 10⁵). It was found that the increment of Ra number increases the rate of heat transfer. However, the effect of Pr number on heat transfer is almost negligible.

Turbine generator operates with complex cooling system due to the challenge in controlling the peak temperature of the stator bar caused by ohm loss, which is unavoidable. Therefore, it is important to characterise and quantifies the thermal performance of the cooling system. The focus of the present research is to investigate the heat transfer and pressure loss characteristics of typical cooling system, so-called stator ventilation duct. A real scale model was built at its operating conditions for the present study. The direction of cooling air is varied to consider its operation condition, so that there are (1) outward flow and (2) inward flow cases. In addition, the effect of (3) cross flow (inward with cross flow case) is also studied. The transient heat transfer method using thermochromic liquid crystals is implemented to measure full surface heat transfer distribution. A series of Computational Fluid Dynamics analysis is also conducted to support the observation from the experiment. For the inward flow case, the results suggest that the average Nusselt number of the 2nd duct is about 30% higher than the 3rd duct. The trend is similar with the effect of cross flow. The CFD results are in good agreement with the experimental data.

This paper predict and effectively control the temperature distribution of the steady-state and transient states of anisotropic four-layer composite materials online, knowing the density, specific heat, heat conductivity and thickness of the composite materials. Based on the transfer function, a mathematical model was established to study the dynamic characteristics of heat transfer of the composite materials. First of all, the Fourier heat transfer law was used to establish a one-dimensional Fourier heat conduction differential equation for each composite layer, and the Laplace transformation was carried out to obtain the system function. Then the approximate second-order transfer function of the system was obtained by Taylor expansion, and the Laplace inverse transformation was carried out to obtain the transfer function of the whole system in the time domain. Finally, the accuracy of the simplified analytical solutions of the first, second and third order approximate transfer functions was compared with computer simulation. The results showed that the second order approximate transfer functions can describe the dynamic process of heat transfer better than others. The research on the dynamic characteristics of heat transfer in the composite layer and the dynamic model of heat transfer in composite layer proposed in this paper have a reference value for practical engineering application. It can effectively predict the temperature distribution of composite layer material and reduce the cost of experimental measurement of heat transfer performance of materials.

Plate fin-tube heat exchangers are widely used in air conditioning and refrigeration systems and other industry fields. Various errors made in the manufacturing process can result in the formation of an air gap between the tube and fin. Several numerical simulations were carried out for a symmetric section of plate fin-tube heat exchanger to study the influence of air gap on heat transfer under periodic flow conditions. Different locations and sizes of an air gap spanning 1/2 circumference of the tube were considered for the range of airflow velocities. Velocity and temperature fields for cases with air gap were compared with ideal thermal contact cases. Blocking of heat flow by the gap leads to the reduction of heat transfer rate. Fin discontinuity in the front of the tube causes the smallest reduction of the heat transfer rate in comparison to the ideal tube-fin contact, especially for thin slits. The rear gap position is the worst in the smallest gap range. Therefore, reversing the flow direction can lead to up to a 15% heat transfer increase, if mainly the rear gaps are present. The introduction of a thin slit in the front of the tube leads to convective heat transfer enhancement, which should be further investigated.

The effect of thermal radiation on the two – dimensional, steady-state, conjugate heat transfer from a circular cylinder with an internal heat source in steady laminar crossflow is investigated in this work. P₀ (Rosseland) and P₁ approximations were used to model the radiative transfer. The mathematical model equations were solved numerically. Qualitatively, P₀ and P₁ approximations show the same effect of thermal radiation on conjugate heat transfer; the increase in the radiation – conduction parameter decreases the cylinder surface temperature and increases the heat transfer rate. Quantitatively, there are significant differences between the results provided by the two approximations.

This article discusses the application of thermal quality control methods for plant tissues. The purpose of the work is to determine the optimal parameters of thermal impact on a spherical-shaped plant control object, ensuring the detection of surface and subsurface defects. The authors of the work proposed mathematical models of the temperature field for a spherical body with defects and a flat sample when exposed to the thermal influence of a pulsed source. As a result of the use of mathematical models, the thermophysical characteristics of plant tissues of varying degrees of disease damage were obtained, which made it possible to simulate the temperature field of the control object and obtain an image of classified tissues. The developed recommendations made it possible to select the optimal parameters of the thermal effect on the test object.

To study the heat and mass transfer characteristics of an evaporative cooler for cooling high-temperature working fluids such as supercritical carbon dioxide, an experimental device of the evaporative cooler was built, and a corresponding test system was constructed. Then, the experimental study was carried out based on the orthogonal test method, and the law and extent of the influence of water flow in the tube, spray water flow rate, inlet water temperature in the tube, and air flow rate on heat dissipation, cooling efficiency, and heat and mass transfer coefficients have been obtained. The correlation equations of the heat and mass transfer coefficients were obtained by fitting the orthogonal experimental data, and the validity of the correlation equations was confirmed by the verification experiment.

Building roofs are sources of unwanted heat for buildings situated in zones with a warm climate. Thus, reflective coatings have emerged as an alternative to reject a significant fraction of solar energy received by roofs. In this research, the thermal behavior of concrete slab-type roofs with traditional and solar reflective coatings was simulated using a computational tool. Weather data from four cities in Mexico with a warm climate were used as boundary conditions. This tool is an in-house code based on the Finite Volume Method developed by the author to perform building components simulations. The code was validated with experimental data from previous work. A series of comparative simulations were developed, taking a gray roof as a control case. The results showed that for the roof without thermal insulation (single roof), the solar reflective coatings reduced the exterior surface between 11 and 16∘C. Consequently, the single roofs’ daily heat gain was reduced by a factor ranging between 41 and 54%. On the other hand, for the insulated roof, the reflective coatings reduced the exterior surface temperature between 17 and 21∘C. At the same time, the daily heat gain of composite roofs was reduced between 37 and 56%.

This investigation aims to discuss the formation process of eddies and the heat transportation in plasma keyhole arc welding. In order to clarify this issue, the measurement of the convection inside the weld pool, the convection on the weld pool surface, also the temperature distribution on the weld pool surface were carried out. The results showed that two eddies were found in the weld pool, which is controlled mainly through the shear force by the plasma flow acting on the weld pool surface. The magnitude, extent and direction of the shear force are thought to be determined primarily by the variation of keyhole profile. The relative shape and strength of each eddy is largely changed depending on the change of the keyhole profile when nozzle diameter changed. These relative strengths of each eddy are considered to decisively govern the heat transport in the weld pool coinciding with the direction of eddies. A larger eddy near the lower part of the keyhole inside the weld pool was found out in the case of 1.6 mm, meanwhile a upward larger eddy was found out near the upper part of the keyhole inside the weld pool in the case of 2.4 mm.

Today with enhancement in technology, sciences, there is also an increase in global heating rate. There is an urgent need of any alternate efficient source to reduce the wastage of energy and to utilize it efficiently. The advanced preparation of Expanded graphite ,lauric acid, stearic acid as shape stabilized phase change material deals with different energy harvesting applications. The main reason behind the need for synthesis of this matrix is to prepare a material that can be used in low temperature energy storage applications. Mixture of lauric acid , stearic acid impregnated in expanded graphite through vacuum impregnation followed by Vacuum Drying and Microwave acid treatment serves as novel shape stabilized phase change material of its type. The microwave acid treatment was done in order to increase the removal of moisture from the sample thus initiating proper bonding of its constituents. The mixture was produced in 1:1:1 ratio where all expanded graphite, lauric acid , stearic acid has one proportions of each other. The product obtained after microwave acid treatment was subjected to SEM, DSC analysis

In this work, we experimentally investigate mass and heat transport phenomena in a modular device while converting a solution salinity difference into a temperature difference. Operations occur under fixed total ambient pressure and without mechanical moving parts, thus realizing a fully static conversion. Provided that a constant salinity gradient can be imposed, the proposed device is able to generate a steady cooling capacity. Here, we purposely operate with environmentally benign and easily accessible sodium chloride water solutions only. A numerical model is finally elaborated, validated and used to explore a wider range of possible device configurations and operating conditions.

This study will present a comprehensive review of the two-phase flow boiling heat transfer coefficient of hydrocarbons such propane (R-290), butane (R-600) and iso-butane (R-600a) and ethanol at various experimental conditions. Studying the multiphase flow heat transfer coefficient has a crucial importance for many heat transfer equipment to achieve higher efficiency for more compact design and cost reduction. One reason behind choosing hydrocarbons as refrigerants in this study is because hydrocarbons have zero ozone depletion potential (ODP=0) and insignificant direct global warming potential (GWP = 3). Moreover, thermodynamic and thermophysical characteristics of hydrocarbons qualify them to be a strong candidate for more heat transfer applications. Initially, by constructing a database for the working fluids from various experimental work available in the literature. The current data that this study has collected for the flow boiling of spans wide ranges of parameters, such as: mass flux, heat flux, operating pressure, and saturation temperature, etc. Furthermore, by comparing the experimental multiphase heat transfer coefficient database with the anticipated values of each correlation, the prediction performance of 26 correlations found in the literature was assessed. This study leads to the selection of the best prediction method based on the minimum deviation of predicted results from the experimental database provided by calculated mean absolute error (MAE) from the assessed correlations. The findings of this study can also be useful in the development of more accurate correlation methods for these fluids and improve the prediction of their flow boiling characteristics.

In the paper the new, fractional order, state space model of a heat transfer in a one- 1 dimensional metallic rod is addressed. The fractional orders of derivative along space and time 2 are not exactly known and they are described by intervals. The proposed model is the interval 3 expanding of the state space fractional model of the one dimensional heat transfer. It is expected to 4 better describe the reality because interval order of each real process is hard to estimate. Elementary 5 properties of the proposed model are analysed. Theoretical results are experimentally validated using 6 data from real experimental laboratory system.

Abstract: In this study, a computational fluid dynamics (CFD) simulation was conducted to validate the CFD model with experimental data from Zimparov et.al (2012), which investigates the heat transfer performance in a spirally corrugated tube that has a twisted tape inserted. The heat transfer was then compared to a simple corrugated tube without the twisted tape and to a smooth tube with no corrugations and no twisted tape. This simulation is compared with a previous experimental study conducted by (Zimparov et al. 2012), which focuses on tubes with a height-to-diameter ratio e/Di > 0.04 and small relative pitches of the twisted tape, H/Di. The largest improvement was noticed in the tube with e/Di= 0.057 and ridge pitch-to-height ratio p/e=6.77 with a twisted tape of H/Di= 4.7. This tube is labeled 5035. Tube 5035 was found to have the most significant enhancement, hence the focus of the CFD simulation will be on this tube, and the simulation will range for Reynolds numbers, 3.5 x 103 < Re < 5.0 x 104. The focus of this simulation is the evaluation of heat transfer and friction factors; a metric was used to obtain an empirical representation of the tube’s performance. Keywords: Spirally corrugated tube; Twisted tape; Heat transfer enhancement; Friction factor; Nusselt number; Computational fluid dynamics (CFD); Star CCM+

The DNS of film boiling requires strong computational resources that are difficult to obtain for a daily CFD use by the practitioners of the industrial R&amp;D experts. On the other hand, the film boiling experiments are associated with the usage of the expensive and highly sophisticated apparatus, and the research to this end is found to be relatively difficult due to high heat flow rates that are present in the process itself. When combined with a transient heat conduction in a solid, the problem becomes significantly difficult. Therefore, a novel method in computation of conjugate heat transfer during film boiling in a quiescent liquid has been proposed in this paper. The method relies on the solution of mass, momentum and energy conservation equations in a two-fluid framework, supplemented with the appropriate closures. Furthermore, the turbulent flow has been found as an important parameter in obtaining the accurate solution of the temperature field evolution in a solid specimen, via the proper modeling of turbulent kinetic energy (TKE) value, that has been imposed as a constant value, i.e., the frozen turbulence approach. It was found, in addition, that the appropriate TKE value can be obtained by use of Kelvin-Helmholtz instability theory in conjunction with the boundary layer theory. The obtained results show excellent agreement with the experimental data within the first 15 s of the experiment, i.e., the first ca. 10 % of the total duration of the film boiling mode of heat transfer. Furthermore, the heat transfer coefficient has matched the error bands prescribed by the authors of the paper that has presented the correlations, whilst the averaged values are far beyond this band, i.e., are slightly more than 30 % higher. The further inspection has revealed a measure of similarity between the computational result of the volume fraction field distribution and the experiment, thus confirming the capability of the method to obtain realistic interface evolution in time. The method has shown full capability for further pursuing the industrial-scale film boiling problems that involve turbulent flow and the conjugate heat transfer approach.

The pulsating flow is one of the techniques which can enhance heat transfer, therefore leading to energy saving in tubular heat exchangers. This paper investigates the heat transfer and flow characteristics in a two-dimensional in-line tube bundle with the pulsating flow by a numerical method using the Ansys Fluent. Numerical simulation is performed for Reynolds number Re = 500 with different frequencies and amplitude of pulsation. Heat transfer enhancement was estimated from the central tube of the tube bundle. Pulsation velocity had an asymmetrical character with a reciprocating flow. The technique developed by the authors to obtain asymmetric pulsations was used. This technique allows simulating an asymmetric flow in heat exchangers equipped with a pulsation generation system. Increase in both the amplitude and the frequency of the pulsations has a significant effect on heat transfer enhancement. Heat transfer enhancement is mainly observed in the front and back of the cylinder. At a steady flow in these areas, heat transfer is minimal due to the weak circulation of the flow. The increase in heat transfer in the front and back of the cylinder is associated with increased velocity and additional flow mixing in these areas.

To overcome the two-phase flow instability of traditional boiling heat dissipation technologies, a porous wick was used for liquid-vapor isolation, thus realizing efficient and stable boiling heat dissipation. A pump-assisted capillary phase-change loop with methanol as working medium was established to study the effect of liquid-vapor pressure difference and heating power on its start-up and steady-state characteristics. The results indicated that the evaporator undergoes four heat transfer modes including flooded, partial flooded, thin film evaporation and overheating. The thin film evaporation mode was the most efficient one with the shortest start-up period. Besides, the heat transfer modes were determined by liquid-vapor pressure difference and power. The heat transfer coefficient could be significantly improved and the thermal resistance could be reduced by increasing liquid-vapor pressure difference as long as it did not exceed 8 kPa. However, when the liquid-vapor pressure difference exceeded 8kPa, its influence on the heat transfer coefficient weakened. In addition, a two-dimensional heat transfer mode distribution diagram considering both liquid-vapor pressure difference and power was drawn through a great number of experiments. During engineering application, the liquid-vapor pressure difference can be controlled to maintain efficient thin film evaporation in order to achieve the optimum heat dissipation effect.

The aim of this paper is to expose the main involved physical phenomena underlying the alteration of convective heat transfer in a heat exchanger subjected to imposed vibrations. This technique seems to have interesting features and industrial applications, such as efficiency increase, heat transfer rate control and cleanliness action. However, a clear description and comprehension of how vibrations may alter the convective heat transfer coefficient in a heat exchanger is no still reached due to the complexity of the involved physical mechanisms. For this reason, after a presentation and a schematisation of the analyzed thermodynamic system, the fundamental alterations of the thermo-fluid dynamics fields are described. Then, the main involved physical phenomena are exposed for the three cases of gaseous, monophasic liquid and boiling liquid mediums. Finally, on the basis of the characteristics of these described phenomena, some considerations and indications of general validity are presented.

The building envelope has the most significant contribution in the reduction of the building energy consumption. Application of new, alternative and improved materials and systems has an important impact on the buildings performances. This paper is focused on the thermal transmittance, as an indicator of the thermal conductance of the construction element. It includes comparisons of the U-values, calculated by software, with those measured in situ on three representative façade walls. The walls have been constructed with the new wall system Fragmat NZ-1, a new product in Macedonian buildings. This research provides basic information on the thermal transmittance of the system. The results of the analysis show that the in situ measuring is a useful tool in validation of the precision of analytically calculated values, since it was difficult to obtain precise results from the analytical calculations only, especially when the layers are with non-uniform thickness.

This article investigates the features of heat and mass transfer for the steady two-dimensional Williamson nanofluid flow across an exponentially stretched surface depending on suction/injection. The boundary conditions incorporate the impacts of the Brownian motion and thermophoresis boundary. The analysis of heat transfer is carried out for the two cases of prescribed exponential order surface temperature (PEST) and prescribed exponential order heat flux (PEHF). The ongoing flow problem is mathematically modeled under the basic laws of motion and heat transfer. The similarity variables are allowed to transmute the governing equations of the problem into a similarity ordinary differential equation (ODEs). The solution of this reduced non-linear system of ODEs is supported by the Homotopy analysis method (HAM). The combination of HAM arrangements is acquired by plotting the h-curve. In order to evaluate the influence of several emergent parameters, the outcomes are presented numerically and are plotted diagrammatically as a consequence of velocity, temperature and concentration pro les.

The heritage of ancient buildings is an important part of the world's history and culture, which has an extremely rich historical-cultural value and artistic research value. Beijing has a large number of palace ancient buildings, and because of the age of their construction, many of them have problems of varying degrees of peeling and mold on the inner surfaces of the envelope. To solve the problems of the damp and moldy interior of palace buildings, a mathematical model of indoor heat and moisture transfer was established based on a wooden palace ancient building in Beijing. Through the indoor mold distribution validation model, the effects of outdoor humidity, soil moisture, wall humidity, and other factors on the indoor heat and moisture transfer of ancient buildings were simulated and analyzed by using the control variables method. The results showed that the molds were distributed at the indoor corners and floors, and the simulation of indoor humidity match the measured humidity. Thus, the simulation results were consistent with the actual situation. The variable trend of the relative humidity of the indoor environment with the outdoor humidity is inconsistent from plane to plane, i.e. it increases or remains constant with the increase of the outdoor humidity. The indoor ambient relative humidity increased with increasing the wall humidity. And the indoor average temperature is 23.3 ℃ and indoor relative humidity ranged between 90.9 % to 92.44 %. Soil moisture and wall humidity were the main factors affecting the indoor environmental relative humidity.

The steady-state, coupled heat and mass transfer from a fluid flow to a sphere accompanied by an exothermal catalytic chemical reaction on the surface of the sphere is analysed taking into consideration the effect of thermal radiation. The flow past the sphere is considered steady, laminar and incompressible. The radiative transfer is modeled by P₀ and P₁ approximations. The mathematical model equations were discretized by the finite difference method. The discrete equations were solved by the defect correction – multigrid method. The influence of thermal radiation on the sphere surface temperature, concentration and reaction rate was analysed for three parameter sets of the dimensionless reaction parameters. The numerical results show that only for very small values of the Prater number the effect of thermal radiation on the surface reaction is not significant.

This work probes the combined effects of magnetic field and viscous dissipation on heat field and examine the second law analysis (entropy generation) in an electrically conducting fluid under the effect of wall mass transfer over continuous stretched non-isothermal surface with variable viscosity. The viscosity of the fluid is assumed to be an inverse linear function of temperature. The governing equation for the problem are changed to dimensionless ordinary differential equations by using similarity transformation and solved numerically by using Rung Kutta and Shooting technique. Velocity, concentration and temperature distribution are obtained and used to compute the entropy generation and the Bejan number in the flow field. The effect of variable viscosity, Schmidt number, Hartman and Reynolds number on the velocity, concentration, temperature, entropy generation and Bejan number are studied and discussed.

Homogeneous and heterogeneous chemical reactions in partially ionized magneto-nano-liquid are investigated theoretically using finite element method (FEM). The effects of ions and electrons collisions on the transport of heat and mass are analyzed for both the cases of heterogeneous and homogeneous chemical reactions. The simultaneous effects of dispersion of nanosized particles in partially ionized nano-liquid in the presence of magnetic field are also investigated. Through numerical experiments, it is noted that the temperature of partially ionized nano-liquid increases when electrons collision rate and ion collisions are increased. The transport rate of reacting species decreases when heterogeneous and homogeneous chemical reactions strengths are increased. It is also observed that the effect of electron collisions on the flow in y-direction is the same to that of ion collisions on the flow in y-direction. Homogeneous and heterogeneous chemical reactions have similar effects on concentration of chemically reacting species in qualitative sense. However, in quantitative sense, homogeneous chemical reaction has more significant effect on the concentration reacting species as compared to heterogeneous chemical reaction.

This study investigated the evolution of density, gas permeability and thermal conductivity of sugar maple wood during the thermo-hygro-mechanical densification process. The results suggested that the oven-dry average density of densified samples was significantly higher than that of the control samples. However, the oven-dry density did not show a linear increase with the decrease of wood samples thickness. The radial intrinsic gas permeability of the control samples was 5 to 40 times higher than that of densified samples, which indicated that the void volume of wood was reduced notably after the densification process. The thermal conductivity increased by 0.5 - 1.5% per percent increase of moisture content for densified samples. The thermal conductivity of densified wood was lower than that of the control samples. The densification time had significant effects on the oven-dry density and gas permeability. Both the densification time and the moisture content had significant effects on thermal conductivity, but their interaction effect was not significant.

The study of different forms of preconditioners for solving a system of nonlinear equations, by using Newton’s method, is presented. The preconditioners provide numerical stability and rapid convergence with reasonable computation cost, whenever chosen accurately. Different families of iterative methods can be constructed by using a different kind of preconditioners. The multi-step iterative method consists of a base method and multi-step part. The convergence order of base method is quadratic and each multi-step add an additive factor of one in the previously achieved convergence order. Hence the convergence of order of an m-step iterative method is m + 1. Numerical simulations confirm the claimed convergence order by calculating the computational order of convergence. Finally, the numerical results clearly show the benefit of preconditioning for solving system of nonlinear equations.

In this paper, we study the well-posedness and asymptotics of a one-dimensional thermoelastic laminated beam system either with or without structural damping, where the heat conduction is given by Fourier's law effective in the rotation angle displacements. We show that the system is well-posed by using Lumer-Philips theorem, and prove that the system is exponentially stable if and only if the wave speeds are equal, by using the perturbed energy method and Gearhart-Herbst-Prüss-Huang theorem. Furthermore, we show that the system with structural damping is polynomially stable provided that the wave speeds are not equal, by using the second-order energy method.

The study of turbulent heat transfer in liquid metal flows has gained interest because of applications in several industrial fields. The common assumption of similarity between the dynamical and thermal turbulence, namely the Reynolds analogy, has been proven to be not valid for these fluids. Many methods have been proposed in order to overcome the difficulties encountered in a proper definition of the turbulent heat flux, such as global or local correlations for the turbulent Prandtl number or four parameter turbulence models. In this work we assess a four parameter logarithmic turbulence model for liquid metals based on RANS approach. Several simulation results considering fluids with Pr = 0.01 and Pr = 0.025 are reported in order to show the validity of this approach. The Kays turbulence model is also assessed and compared with integral heat transfer correlations for a wide range of Peclet numbers.

This paper introduces a new adaptation of the enthalpic lattice Boltzmann method (LBM) tailored to simulate the intricate dynamics of conjugate heat transfer in non-homogeneous media, showcasing considerable potential for enhancing heat exchanger designs. This approach expands upon the conventional enthalpic LBM framework by seamlessly incorporating tailored source terms, enabling precise representation of local and transient variations in the medium’s thermophysical properties. The resulting LBM model comprehensively captures the energy conservation equation, with exceptions made only for flow compressibility and viscous dissipation, thereby significantly augmenting its versatility in analyzing heat exchanger configurations. Verification tests, comprising assessments of both transient and steady-state solutions, unequivocally validate the accuracy of the proposed model, further bolstering its reliability for analyzing heat exchange processes within intricate heat exchanger geometries. To demonstrate its efficacy, simulations of conjugate heat transfer processes involving fluid natural convection within structured cavities were performed, imposing both Dirichlet and Neumann boundary conditions to emulate scenarios encountered in practical heat exchanger operations. The findings yield compelling insights, particularly in the transient regime, revealing the beneficial impact of structured cavities on enhancing heat transfer processes. These insights inform potential design optimizations for heat exchangers. The results emphasize the potential of the modified enthalpic LBM approach to elucidate complex heat transfer phenomena in non-homogeneous media and structured geometries, offering valuable implications for heat exchanger engineering and optimization.

Pool boiling heat transfer is recognized as one of the most effective heat transfer methods and has extensive applications in industry. The application of non-azeotropic binary mixtures can not only meet the environmental requirements of modern industrial development, but also improve the coefficient of performance (COP) of many systems. Therefore, studying the boiling heat transfer characteristics of non-azeotropic mixtures is important on improving their potential industrial application. This article selected ethylene glycol/deionized water (EG/DW) at varies concentration as the research working fluids, and conducted experimental research on the pool boiling performance. At the same time, the thermophysical parameters of the mixtures were studied and analyzed. The results showed that the concentration of EG in the mixture had a significant impact on the thermal properties and temperature glide of the mixture, where both affected the heat transfer deterioration. Based on experimental data, six widely used heat transfer coefficient prediction correlations were used for calculation, and two of them were modified. The deviation between the modified correlations and the experimental results remained within 20%.

The future power equipment tends to take hydrogen or middle/low heat-value syngas as fuel for low emission. The heat transfer of film cooled turbine blade shall be influenced more by radiation. Its characteristic of conjugate heat transfer is studied experimentally and numerically in the paper by considering radiation heat transfer, multi-composition gas and TBC. The Weighted Sum of Gray Gases spectral model and Discrete Transfer Model are utilized to solve the radiative heat transfer in the multi-composition field, while validated against the experimental data for the studied cases. It is shown that the plate temperature increases significantly when considering the radiation and the temperature gradient of the film cooled plate becomes larger. It is also shown that increasing percentage of steam in gas composition results in increased temperature on the film-cooled plate. The normalized temperature of the film-cooled plate decreases about 0.02, as the total percentage of steam in hot gas increases per 7%. As for the TBC effect, it can smooth out the the temperature distribution and insulate the heat to a greater extent when the radiative heat transfer becomes significant.

Drying grains in a fixed bed can be an interesting alternative to prevent undesirable breaks and fractures of solids due to mechanical shocks, something that cannot be avoided when drying in moving beds. A disadvantage of fixed bed drying is that there can be significant gradients in the critical variables if the layer of particulate solids is thick. This work shows that periodically changing the direction of drying air flow is an effective technique to reduce differences within the bed and allow better uniformity of the product. Drying in a thick layer of 10 cm of sorghum grains was carried out at 50 and 60oC for air flow velocity of 2.1 m.s-1. The results showed that despite increasing the total drying time, the technique actually allowed a significant decrease in the temperature gradients and moisture content of the sorghum grains. The change in direction of the air flow caused the drying front to be displaced, sometimes towards the top, sometimes towards the base of the bed. At 50oC, drying lasted a total of 240 min, bringing the sorghum grains to an average overall moisture content of 0.13 on a dry basis.

Theoretical approaches were applied to study the effect of magnetic field and heat transfer on the flow of blood plasma through an asymmetric arterial segment. The plasma was considered to be unsteady, laminar and an incompressible fluid through non-uniform arterial segment in a two-dimensional flow. Axial velocity, pressure gradient, stream function and pressure shift per wavelength were evaluated in blood plasma flow in arteries by use of coupled linear partial differential equations, solved with the help of Finite difference method. The corresponding initial and boundary conditions were obtained by discretizing the flow channel. The effect of magnetic field on blood plasma in arteries was determined by creating a magnetic field gradient through the application of a varying strength of magnetic field on the flow. Heat transfer characteristics due to applied magnetic field and viscosity of blood was obtained by use of linear partial differential equations to determine varying temperature conditions in heat transfer characteristics. Numerical results for velocity profiles, magnetic profiles and temperature profiles were obtained to characterize blood plasma viscosity by use of various non-dimensional parameters. The results were graphically presented using MATLAB software. The results obtained helped in analyzing theoretically the effects of magnetic field and heat transfer in arterial plasma flow.

Enhancing energy efficiency within the building sector is imperative to curbing energy losses, given that this sector alone contributes to over 34% of global energy consumption. Employing a building management system, along with its regular updates, presents a strategic avenue to decrease energy usage, enhance building energy efficiency, and more. Tailored control strategies, aligned with the unique characteristics and usage patterns of each building, are essential for achieving energy savings. This article presents an evaluation of HVAC system efficiency in office buildings, utilizing a data-driven approach coupled with simulations conducted in IDA ICE software. The research explores the control strategy of an office building equipped with a constant air volume HVAC system, featuring a regularly controlled air handling unit. The objective is to boost energy efficiency while striking a balance between occupant comfort and energy consumption. Findings indicate that by analyzing measured data and adjusting configurable parameters, building energy consumption can be significantly reduced. Close monitoring of indoor parameters by building operators and corresponding adjustments to the HVAC system can yield energy savings of up to 16%. Leveraging these insights, the paper suggests integrating data-driven and dynamic simulation methods into building management system models to optimize HVAC systems, enhance energy efficiency, and advance ambitious carbon neutrality objectives.

Since the photocatalytic reaction is a surface reaction, enhancing the gas movement around photocatalyst would promote photocatalytic CO₂ reduction performance. A new approach to enhance the gas movement around the photocatalyst by the natural thermosiphon movement of gasses around photocatalyst using black body material was proposed and confirmed experimentally, but the heat transfer mechanism on the phenomena was not clarified yet. The purpose of this study is to clarify the heat transfer mechanism of it. This study calculated the temperature of mixed gases of CO₂ and NH₃ around P₄O₁₀/TiO₂ photocatalyst by the heat transfer formula. It is revealed that there was no difference between the increase temperature (T_g) from the temperature at the beginning of the CO₂ reduction experiment (T_ini) and the temperature of mixed gases of CO₂ and NH₃ measured by thermocouple in the experiment (T_e) under the illumination condition with a visible light (VIS) + an infrared light (IR) and IR only. The heat transfer model proposed by this study has predicted T_g well under the illumination condition with VIS + IR and IR only well. On the other hand, it is revealed that the difference between T_g and T_e was as large as 10 ℃ under the illumination condition with an ultra violet light (UV) + VIS + IR.

Biohydrogen is a versatile energy carrier for the generation of electric energy from renewable sources. Hydrogenases can be used in enzymatic fuel cells to oxidize dihydrogen. The rate of electron transfer (ET) at the anodic side between the [NiFe]-hydrogenase enzyme distal iron-sulfur cluster and the electrode surface can be described by the Marcus equation. All parameters for the Marcus equation are accessible from DFT calculations. The distal cubane FeS-cluster has a three cysteine and one histidine coordination [Fe₄S₄](His)(Cys)₃ first ligation sphere. The reorganization energy (inner- and outer-sphere) is almost unchanged upon a histidine-to-cysteine substitution. Differences in rates of electron transfer between the wild-type enzyme and the all-cysteine mutant can be rationalized by a diminished electronic coupling between the donor and acceptor molecules in the [Fe₄S₄](Cys)₄ case. The fast and efficient electron transfer from the distal iron-sulfur cluster is realized by a fine-tuned protein environment which facilitates the flow of electrons. This study enables the design and control of electron transfer rates and pathways by protein engineering.

The computational model that is able to estimate the temperature distribution inside a solid specimen during the film boiling phase of immersion quenching (water entry) process has been presented in paper, and it is based on the prescribed initial temperatures of the solid specimen and the liquid quenchant. In addition, the turbulence effects have to be considered using the assumed turbulence kinetic energy value, i.e., the “frozen turbulence” approach, that remains constant thorough the simulation. The studied material is nickel alloy, Inconel 600, for which the extensive experimental data is available. The work has been carried out using ANSYS Fluent computational fluid dynamics software and the methods for solution of Stefan problem by Eulerian two fluid VOF model.. A satisfactory agreement between the experimental and the calculated data has been achieved, yielding thereby the computationally obtained data that fits to a great extent to the prescribed error band of ± 10 % during the estimated film boiling phase of the immersion quenching process itself.

The study of the influence of the nanoparticle volume fraction and aspect ratio of microchannels on the fluid flow and heat transfer characteristics of nanofluids in microchannels is important in the optimal design of heat dissipation systems with high heat flux. In this work, the computational fluid dynamics method was adopted to simulate the flow and heat transfer characteristics of two types of water–Al2O3 nanofluids with two different volume fractions and five types of microchannel heat sinks with different aspect ratios. Results showed that increasing the nanoparticle volume fraction reduced the average temperature of the liquid–solid heat transfer surface and thereby improved the heat transfer capacity of the nanofluids. Meanwhile, the increase of the nanoparticle volume fraction led to a considerable increase in the pumping power of the system. Changing the aspect ratio of the microchannel effectively improved the heat transfer capacity of the heat sink. Moreover, increasing the aspect ratio effectively reduced the average temperature of the heating surface of the heat sink without significantly increasing the flow resistance loss. When the aspect ratio exceeded 30, the heat transfer coefficient did not increase with the increase of the aspect ratio. The results of this work may offer guiding significance for the optimal design of high heat flux microchannel heat sinks.

Windows account for a significant proportion of the total energy lost in buildings. The interaction of window type, Window-to-Wall Ratio (WWR) scheduled and window placement height would influence the natural lighting and heat transfer through windows. This is a pressing issue for non-tropical regions considering their high emissions and distinct climatic characteristics. A limitation exists in the adoption of common simulation-based optimisation approaches in the literature, which are hardly accessible to practitioners. This article develops a numerical-based window design optimisation model using a common Building Information Modelling (BIM) platform adopted throughout the industry, focusing on non-tropical regions of Australia. Three objective functions are proposed; the first objective is to maximize the available daylight, and the other two emphasize on the undesirable heat transfer through windows in summer and winter respectively. The developed model is tested on a case study located in Sydney, Australia, and a set of Pareto-optimum solutions is obtained. Through the use of the proposed model, energy savings of up to 16.43% are achieved. Key findings on the case example indicate that leveraging winter heat gain to reduce annual energy consumption should not be the top priority when designing windows for Sydney.

Nanofluids are a novel class of heat transfer fluid that plays a vital role in industries. In mathematical investigations, these fluids are modeled in terms of traditional integer-order partial differential equations (PDEs). It is recognized that traditional PDEs cannot decode the complex behavior of physical flow parameters and memory effects. Therefore, this article intends to study the mixed convection heat transfer in nanofluid over an inclined vertical plate via fractional derivatives approach. The problem in hand is modeled in connection with Atangana-Baleanu fractional derivatives without singular and local kernel having strong memory. The human blood is considered as base fluid dispersing carbon nanotube (CNTs) (single-wall carbon nanotubes (SWCNTs) and multi-wall carbon nanotubes(MWCNTs )) into it to form blood-CNTs nanofluid. The nanofluids are considered to flow in a saturated porous medium under the influence of an applied magnetic field. The exact analytical expressions for velocity and temperature profiles are acquired using the Laplace transform technique and plotted in various graphs. The empirical results indicate that the memory effect decreases with increasing fractional parameters in the case of both temperature and velocity profiles. Moreover, the temperature profile is higher for blood-SWCNTs by reason of higher thermal conductivity whereas, this trend is opposite in case of velocity profile due densities difference.

Surface initiated atom transfer radical polymerization (SI-ATRP) is one of the most versatile technique to modify the surface properties of material. Recent developed metal free SI-ATRP makes such technique more widely applicable. Herein photo-induced metal-free SI-ATRP of methacrylates, such as methyl methacrylate, N-isopropanyl acrylamide, and N,N- dimethylaminoethyl methacrylate, on the surface of SBA-15 was reported to fabricate organic-inorganic hybrid materials. SBA-15 based polymeric composite with adjustable graft ratio was obtained. The structure evolution during the SI-ATRP modification of SBA-15 was monitored and verified by FT-IR, XPS, TGA, BET, and TEM. The obtained polymeric composite showed enhanced adsorption ability for the model compound toluene in aqueous. This procedure provides a low cost, ready availability, and facile modification way to synthesize the polymeric composites without the contamination of metal.

The radiative heat transfer in arc plasma models is considered from the point of view of its description in terms of a net emission coefficient, the method of spherical harmonics in its lowest order, and the discrete ordinate method. Net emission coefficients are computed applying approximate and numerical approaches, the multi-band representation of the spectral absorption coefficient with three kinds of its averaging and two datasets. The self-consistent access to the radiative heat transfer is applied to a two-dimensional axisymmetric model of free-burning arc in argon at atmospheric pressure. The results obtained from the models employing the net emission coefficient, the method of spherical harmonics, and the discrete ordinate method are compared.

Regeneratively cooled scramjet has already been successfully verified as propulsion device for hypersonic vehicle. As a result, dynamic process of flow and heat transfer in cooling channel is commonly occurred which may bring hazard and control difficulties for scramjet. To study transient flow and heat transfer process in cooling channel, a dynamic numerical model is established. Dynamic characteristics of flow and heat transfer under different conditions are calculated and discussed, which includes change of inlet fuel mass flow, heat flux and pressure working conditions. Results show that stable time of cooling channel outlet fuel temperature is related to the change rate of inlet mass flow and heat flux. The stable time of outlet fuel temperature under heat flux decreasing working conditions are about 12.5 s. The initial response of working pressure fluctuation will lead to fuel temperature fluctuation, which has little effect on wall temperature.

This paper presents an innovative multi-agent, data-driven reinforcement learning (RL) approach to develop and utilize the thermal equivalent network model that represents the motor's thermal dynamics. A multi-agent reinforcement learning is designed and trained to adjust the model parameters using data from several motor driving cycles. To ensure the incoming driving cycle matches the historical data before employing the pre-trained RL agents, offline statistical analysis and clustering techniques are developed and used. Numerical simulations highlighted the RL agent's ability to develop strategies that effectively address the variability of driving cycles. The proposed RL framework showed its capability to accurately reflect the motor's thermal behavior under various driving conditions.

Despite being stored at 113 K and atmospheric pressure, LNG cold potential is not exploited to reduce green ships’ energy needs. An innovative system based on three Organic Ranking Cycles integrated into the regasification equipment is proposed to produce additional power and recover cooling energy from condensers. A first-law analysis identified ethylene and ethane as suitable working fluids for the first and the second ORC making available freshwater and ice. Propane, ammonia and propylene could be arbitrarily employed in the third ORC for air-conditioning. An environmental analysis that combines exergy efficiency, ecological indices and hazard aspects for marine environment and ship’s passengers, indicated propylene as safer and more environmentally friendly. The exergy analysis confirms more than 20% of the LNG potential can be recovered from every cycle to produce a net clean power of 76 kW, whereas 270 kW can be saved by recovering condensers' cooling power to satisfy some ship needs. Assuming the sailing mode, a limitation of 162 kg in LNG consumptions was determined, avoiding the emission of 1584 kg of CO2 per day. Marine thermal pollution is reduced by 3.5 times by recovering the working fluids' condensation heat for the LNG pre-heating.

Nonlinear thermal transport of non-Newtonian polymer flows is an increasingly important area in materials engineering. Motivated by new developments in this area which entail more re-fined and mathematical frameworks, the present analysis investigates the boundary layer ap-proximation and heat transfer persuaded by a symmetrical cylindrical surface positioned hori-zontally. To simulate thermal relaxation impacts the bioconvection cross nanofluid flow Buongiorno model is deployed. The impact of the magnetic field applied on the nanofluid using the heat generation and melting phenomena are inspected. The nonlinear effect of thermosolutal buoyant forces is incorporated into the proposed model. The novel mathematical equations comprise thermophoresis and Brownian diffusion effects. Via robust transformation techniques, the primitive resulting partial equations for momentum, energy, concentration, and motile living microorganism are rendered into nonlinear ordinary equations with convective boundary postulates. An explicit and efficient numerical solver procedure in Mathematica 11.0 programming platform is developed to engage the nonlinear equations. The consequence of multiple governing parameters on dimensionless fluid profiles is inspected through plotted visuals and tables. Finally, outcomes declared on the surface drag force, heat, and mass transfer coefficients are exhibited through 3D visuals via different influential parameters.

Most of the pore-scale imaging and simulations of non-Newtonian fluid are based on the simplifying geometry of network modeling and overlook the fluid rheology and heat transfer. In the present paper, we developed a non-isothermal and non-Newtonian numerical model of the flow properties at pore-scale by direct simulation of the 3D micro-CT images using a Finite Volume Method (FVM). The numerical model is based on the resolution of the momentum and energy conservation equations. Owing to an adaptive meshing technique and appropriate boundary conditions, rock permeability and mobility are accurately computed. A temperature and concentration-dependent power-law viscosity model in line with the experimental measurement of the fluid rheology is adopted. The model is first applied at isothermal condition to 2 benchmark samples, namely Fontainebleau sandstone and Grosmont carbonate, and is found to be in good agreement with the Lattice Boltzmann method (LBM). Finally, at non-isothermal conditions, an effective mobility is introduced that enables to perform a numerical sensitivity study to fluid rheology, heat transfer, and operating conditions. While the mobility seems to evolve linearly with polymer concentration, the effect of the temperature seems negligible by comparison. However, a sharp contrast is found between carbonate and sandstone under the effect of a constant temperature gradient. Besides concerning the flow index and consistency factor, a good master curve is derived when normalizing the mobility for both the carbonate and the sandstone.

To enhance the applicability of dual-phase high-entropy alloys (HEAs) like Fe32Cr33Ni29Al3Ti3, fabricated via selective laser melting (SLM), a focus on improving their mechanical properties is essential. As part of this effort, heat treatment was explored. This study compares the microstructure and mechanical properties of the as-printed sample with those cooled in water after undergoing heat treatment at temperatures ranging from 1000 to 1200 ℃ for 1 hour. Both pre- and post-treatment samples reveal a dual-phase microstructure comprising FCC and BCC phases. Although heat treatment led to a reduction in tensile and yield strength, it significantly increased ductility compared to the as-printed sample. This strength-ductility trade-off is related to changes in grain sizes with ultrafine grains enhancing strength and micron grains optimizing ductility, also the influence of the content of FCC/BCC phases and dislocation density. In particular, the sample heat-treated at 1000 °C for 1 hour and then water-cooled exhibited a better combination of strength and ductility, a yield strength of 790 MPa, and an elongation of 13%. This research offers innovative perspectives on crafting dual-phase HEA of Fe32Cr33Ni29Al3Ti3, allowing for tailorable microstructure and mechanical properties through a synergistic approach involving SLM and heat treatment.

Space shuttle has been a hall mark of American space program since its inception. Despite its temporary shutdown few years ago, with the recent interest in space exploration which includes revitalizing human outpost in microgravity and transportation required to build it, realize other experiments (e.g. in space telescopes, in space manufacturing) and interplanetary voyages, it has regained attention. Its superior design, manufacturing, materials, performance, durability, and efficiency place it among the best, in fact, the only effort by mankind to build a reusable craft horizontally, launch vertically like a rocket and fly back like a plane. Various requirements emerge during its design (thermal, fluid, acoustics, vibration and structural) and design of its main engine (Aerojet Rocketdyne RS 25) which requires considerable attention, heat transfer being most important. This facilitated and necessitated use of various types of heat exchangers such as single coil, heat pipe, built in internal heat exchanger (IHEX), external heat exchanger (EHEX), condensing heat exchanger (CHEX), Interface heat exchangers (InHEX), regenerative heat exchanger (RHEX) and compact heat exchangers (CoHEX), change, manipulate and optimize their configurations in piping and instrumentation diagrams (PIDs). In this short narrative, an effort has been made to summarize them, and their developments over time with a focus on the application, design, manufacturing, materials, and performance (in service and final operation).

The CMT (Cold Metal Transfer) arc welding process is a convenient instrument for the assembly of thin sheets [1], [2]. More particularly, it permits the decrease of the amount of heat transferred to the parts to-be assembled, thus reducing their subsequent deformations. The present work aims at simulating the CMT welding of thin stainless-steel sheets in order to develop an approach that allows the prediction of temperature fields, as well as final deformations induced by the welding process. For that purpose, instrumented tests and numerical simulations were set aiming at comparing the experiments with simulations. Butt-welding of stainless-steel sheets was considered, with a thickness ranging from 1 to 1.2 mm. The weld seam samples were observed in order to set an equivalent heat source for each configuration. Moreover, the electric current and voltage were surveyed, and temperature measurements were performed using K-type thermocouples. In addition, displacement measurements were obtained using the DIC (Digital Image Correlation) technique. Thermomechanical simulations were then carried out using an equivalent heat source approach, considering the phase changes of elements, i.e. the transitions from solid to liquid and from liquid to solid. These simulations also consider the actual geometry of seams induced by addition of a filler material.

In this study, we present comprehensive climatologies of effective ultraviolet (UV) quantities and photosynthetically active radiation (PAR) over Cyprus for the period 2004 to 2023, leveraging the synergy of earth observation (EO) data and radiative transfer model simulations. The EO dataset, encompassing satellite and re-analysis data for aerosols, total ozone column, and water vapor, alongside cloud modification factors, to capture the nuanced dynamics of Cyprus's atmospheric conditions. With a temporal resolution of 15 minutes and a spatial of 0.05°x0.05°, these climatologies undergo rigorous validation against established satellite datasets and are further evaluated through comparisons with ground-based global horizontal irradiance measurements provided by the Meteorological Office of Cyprus. This dual-method validation approach not only underscores the models' accuracy but also highlights their proficiency in capturing intra-daily cloud coverage variations. Our analysis extends to investigating the long-term trends of these solar radiation quantities, examining their interplay with changes in cloud attenuation, aerosol optical depth (AOD), and total ozone column (TOC). Significant decreasing trends in the noon ultraviolet index (UVI), of -2 to -4% per decade have been found in Autumn, especially marked on the island’s Northeastern part, mainly originating from the (significant) positive trends in TOC. The significant decreasing trends in TOC, of -2 to -3% per decade that were found in Spring do not result in correspondingly significant positive trends in the noon UVI since variations in cloudiness and aerosols also have a strong impact on the UVI in this season. The seasonal trends in the Daylight Integral (DLI) were generally not significant. These insights provide a valuable foundation for further studies aimed at developing public health strategies and enhancing agricultural productivity, highlighting the critical importance of accurate and high-resolution climatological data.

Densely urbanized areas, with a low percentage of green vegetation, are highly exposed to Heat Waves (HW) which nowadays are increasing in terms of frequency and intensity also in the middle-latitude regions, due to ongoing Climate Change (CC). Their negative effects may combine with those of the UHI (Urban Heat Island), a local phenomenon where air temperatures in the compact built up cores of towns increase more than those in the surrounding rural areas, with significant impact on the quality of urban environment, on citizens health and energy consumption and transport, as it has occurred in the summer of 2003 on France and Italian central-northern areas. In this context this work aims at designing and developing a methodology based on aero-spatial remote sensing (EO) at medium-high resolution and most recent GIS techniques, for the extensive characterization of the urban fabric response to these climatic impacts related to the temperature within the general framework of supporting local and national strategies and policies of adaptation to CC. Due to its extension and variety of built-up typologies, the municipality of Rome was selected as test area for the methodology development and validation. First of all, we started by operating through photointerpretation of cartography at detailed scale (CTR 1: 5000) on a reference area consisting of a transect of about 5x20 km, extending from the downtown to the suburbs and including all the built-up classes of interest. The reference built-up vulnerability classes found inside the transect were then exploited as training areas to classify the entire territory of Rome municipality. To this end, the satellite EO HR (High Resolution) multispectral data, provided by the Landsat sensors were used within a on purpose developed "supervised" classification procedure, based on data mining and “object-classification” techniques. The classification results were then exploited for implementing a calibration method, based on a typical UHI temperature distribution, derived from MODIS satellite sensor LST (Land Surface Temperature) data of the summer 2003, to obtain an analytical expression of the vulnerability model, previously introduced on a semi-empirical basis.

The study utilizes the energy-flux-vector method to analyze the heat transfer characteristics of natural convection in a wavy-wall porous square cavity with a partially-heated bottom surface. The effects of the modified Darcy number and modified Rayleigh number on the energy-flux-vector distribution and mean Nusselt number are examined. The results show that when a low modified Darcy number with any value of modified Rayleigh number is given, the recirculation regions are not formed in the energy-flux-vector distribution within the porous cavity. Therefore, a low mean Nusselt number is obtained. The recirculation regions do still not form and thus the mean Nusselt number has a low value when a low modified Darcy number with a high modified Rayleigh number is given. However, when the values of the modified Darcy number and modified Rayleigh number are high, the energy flux vectors generate recirculation regions and thus a high mean Nusselt number is obtained.

In this study, an alternative method to conventional production methods involving thin section copper permanent mould casting (rapid solidification), hot rolling and heat treatment processes to manufacture AISI DC 53 cold work tool steel, has been investigated. In this new method, solidification of the AISI DC 53 was done in the thin section copper mould instead of traditional ingot casting. After solidification, thin slabs obtained was homogenized to 1150 ^oC and hold at this temperature for one hour and then hot rolling was be applied. During hot rolling process, about % 30 reduction in thickness of slab was obtained. After hot rolling, heat treatment (austenitizing, quenching and tempering) have been applied to thin slab. The samples have been taken as cast, as rolled and as heat treated (austenitized and tempered) and the microstructural analysis, hardness tests, retained austenite quantity measurement by XRD method have been performed. The heat treatment and tests have been performed for a commercially available AISI DC 53 which is manufactured by thick section ingot casting and rolling. Hardness values of the AISI DC 53 steels produced by traditional route is in the range of 52-54 HRC after austenitization at 1025 ^oC for one hour and quenched in compressed air and tempered twice at 525 ^oC for 120 mins. On contrary the permanent mould cast AISI DC 53 after homogenization at 1150 ^oC and immediately hot rolling then air cooling and austenitized at 1025 ^oC for one hour then quenched by compressed air and tempered twice at 525 ^oC for 120 mins have hardness valeus in the range of 55-57 HRC. Experiments have revealed that the properties of new rapid solidified steel in permanent copper mould are better than the commercially available steel and have a more refined microstructure than commercially produces alternative. Therefore, the new proposed method can be used as an alternative manufacturing method for cold-work tool steels.

CoCrFeNiMn high-entropy alloy coatings were prepared on compacted graphite iron（CGI） through plasma cladding to strength the CGI substrate. The effects of heat treatment temperatures and times on the microstructure and mechanical properties of the CoCrFeNiMn coatings were investigated. After heat treatment, a single FCC phase was remained in the coating as compared to the deposited one, with smaller dendrites, larger dendritic spacing and more Cr-rich compounds precipitated between dendrites. The coatings’ microhardness was increased after heat treatment. After heat treated at 660°C for 90 minutes, the coating had the highest microhardness of 563±6.9 HV0.2, the lowest frictional coefficient of 0.71 and the smallest wear mass loss of 1.12 mg, and it had the best wear resistance.

The amount of heat transfer in gas turbine blades depends on cooling techniques and various flow phenomena. The effect of eddies, passing shock waves and free flow turbulence has been noticed by many researchers since the beginning. The focus of the upcoming work is on the numerical investigation of the effects of turbulence intensity and Reynolds number on the amount of heat transfer from the blade surface with internal cooling. The SST model has been used to solve this problem, which has been compared with the experimental work to ensure the correctness of the numerical simulation. In this regard, by changing the free flow turbulence intensity with values of 1, 5, 7, and 10% and at three Reynolds numbers of 150,000, 350,000, and 750,000, the changes in heat transfer coefficients have been investigated. The results show that with the increase of the turbulence intensity at different Reynolds numbers, due to the positive effect of the flow turbulence on the suppression of separation and promotion of the boundary layer transition, the blade surface heat transferincreases and this increase is more evident at higher Reynolds numbers.

This paper studies the evaporative heat transfer characteristics of R744 at low temperatures in a horizontal smooth tube as a cascade refrigeration system (CRS) among hybrid cascade refrigeration systems (HCRSs). There is a lack of research on the low-temperature evaporative heat transfer characteristics of R744 under the operating conditions of evaporators used in actual CRSs used in supermarkets. Therefore, this study aims to provide basic data on the evaporative heat transfer characteristics of R744 in the evaporators of refrigerators used in supermarkets. The tube used in the evaporation experiment conducted herein was a smooth horizontal copper tube with an inner diameter and length of 11.46 mm and 8000 mm, respectively. The experimental pa-rameters were as follows: heat fluxes of 12–21.5 kW/m2, mass fluxes of 75–225 kg/(m2·s), and saturation temperatures of −50–−30 °C. The main results are summarized as follows. (1) When designing the R744 evaporator, the mass and heat fluxes must be maximized within the operating conditions, and the saturation temperature must be designed to be as low as possible. (2) The evaporative heat transfer coefficient of R744 can be predicted well by using the correlation formula of Chen at the evaporation temperature of −40 °C in the CRS.

In this paper, the integrated performance of a modular biomass boiler with an existing industrial Rankine steam heat and power cycle and a supplementary supercritical-CO2 (sCO2) Brayton cycle is analyzed. The aim is to leverage the high efficiency supplementary sCO2 cycle to increase net generation and energy efficiency from the existing biomass boiler. Two sCO2 heater configurations situated within the flue gas flow path are investigated, namely a single convective-dominant heater, and a dual heater configuration with a radiative and a convective heater. A quasi-steady-state 1D model was developed to simulate the integrated cycle, including detailed component characteristics for the Rankine and Brayton cycles. The model solves the mass, energy, momentum, and species balance equations. The system is analyzed for three cases: (i) the existing Rankine cycle without the sCO2 integration, (ii) with the single convective-dominant sCO2 heater configuration, and (iii) the dual sCO2 heater configuration. The results show the required rate of overfiring for the sCO2 configurations, with a 15.3% increase in fuel flowrate resulting in an additional 21.2% in net power output. The model quantifies the impact of the sCO2 heaters, with reduced heat uptakes for downstream boiler heat exchangers. Furnace water wall heat uptake increased due to overfiring, offsetting the reduced heat uptakes at downstream evaporative heat exchangers. The dual configuration has more impact on Rankine cycle operation due to the radiative sCO2 heater placement in front of the second superheater, absorbing some of the direct radiation from the furnace.

While the majority of previous studies assessing pain-related variables in psychopaths used electric shocks, little is known about the effectiveness of alternative pain-inducing methods to increase emotional responses such as fear and anxiety. A small sample of healthy undergraduate men (N = 15) was recruited to assess the effectiveness of a heat stimulus to induce pain in an immediate versus delayed punishment paradigm. Although pain catastrophizing, anxiety, and threat of pain did not increase throughout the experiment, participants experienced a significant increase of fear of pain and pain intensity, indicating that the heat stimulus was effective in inducing pain. Furthermore, subjects were slower in initiating the pain stimulus during the first five trials, but no time difference was found during the 15 remaining trials. No correlation was found between psychopathic traits and pain-related variables, with the exception of inconsistent results within the Fearless Dominance factor. Findings are discussed in terms of improvement for a larger scale study involving psychopathic individuals.

The study aimed to determine the effect of heat stress (HS) on reproductive parameters [calving to first service (CTFS) and first service conception rate (FSCR)] and general physiological responses [rectal temperature (RT) and respiratory rate (RR)] in tropical Holstein Friesian dairy cows raised in Ratchaburi province, Thailand. Cows were divided into a moderate HS (n = 22) and a mild HS (n = 22) group. Cycling cows were detected and injected with PGF2α at the beginning of the experimental period. Reproductive and physiological parameters were recorded. The average temperature humidity indices experienced by the cows were 80.67 ± 0.79 and 77.81 ± 1.09 for the moderate and mild HS groups, respectively. Cows showed significantly lower RT and RR in the mild (38.47 ± 0.21°C and 41.04 ± 4.55 bpm, respectively) than in the moderate HS group (38.87 ± 0.15°C and 51.17 ± 10.52 bpm). Under mild HS, cows showed a better response to injection of PGF2α than those under moderate HS. The percentage of cows that ovulated after being induced by PGF2α and showed estrus signs was higher in the mild than the moderate HS groups (54.55% versus 18.18%). Furthermore, the FSCR of cows under mild HS tended to be higher than in the moderate HS group (54.55 % and 42.11%, respectively), while the average CTFS interval was significantly shorter under mild than moderate HS (69.47 ± 18.18 and 84.60 ± 27.68, respectively). These results indicate that HS impairs reproductive performance in cross-bred Holstein cows, especially in moderate HS conditions.

With metal oxide semiconductors being a promising candidate for accurate indoor air quality assessments, multiple drawbacks of the gas sensors prevent their widespread use. Examples include poor selectivity, instability over time, and sensor poisoning. Complex calibration methods and advanced operation modes can solve some of those drawbacks. However, this leads to long calibration times, which are unsuitable for mass production. In recent years, multiple attempts to solve calibration transfer have been made with the help of direct standardization, orthogonal signal correction, and many more methods. Besides those, a new promising approach is transfer learning from deep learning. This article will compare different calibration transfer methods, including direct standardization, piecewise direct standardization, transfer learning for deep learning models, and global model building. The machine learning methods to calibrate the initial models for calibration transfer are feature extraction, selection, and regression (established methods) and a custom convolutional neural network TCOCNN. It is shown that transfer learning can outperform the other calibration transfer methods regarding the root mean squared error, especially if the initial model is built with multiple sensors. It was possible to reduce the number of calibration samples by up to 99.3 % (from 10 days to approximately 2 hours) and still achieve an RMSE for acetone of around 18 ppb (15 ppb with extended individual calibration) if six different sensors were used for building the initial model. Furthermore, it was shown that the other calibration transfer methods (direct standardization and piecewise direct standardization) also work reasonably well for both machine learning approaches, primarily when multiple sensors are used for the initial model.

Noninvasive brain stimulation technique can be used for modulation of motor behaviors such as reaction time (RT). The main aim of this study was to investigate whether RT during a sequential visual isometric pinch task (SVIPT) can be affected by anodal transcranial direct current stimulation (a-tDCS) over three different stimulation sites such as dorsolateral prefrontal cortex (DLPFC), primary motor cortex (M1) or posterior parietal cortex (PPC). We also aimed to assess if stimulation of these cortical sites affect the transfer of learning during SVIPT. A total of 48 right-handed healthy participants were randomly assigned to one of the four a-tDCS groups: 1) left M1, 2) left DLPFC, 3) left PPC and 4) sham. A-tDCS was applied concurrent with SVIPT in which the participants were precisely controlled their forces to reach seven different target forces from 10 to 40% of maximum voluntary contraction (MVC) presenting on a computer screen with right dominant hand. Four test blocks were randomly performed at baseline and 15 min after the intervention including sequence and random blocks with either hand. Our results showed significant differences between a-tDCS groups on ratio RT in the sequence blocks of both the right trained (P = .041) and left untrained hands (P = .023) for target forces of 15% and 30 % of MVC, respectively. In sequence blocks, M1 showed significant elongation in ratio RT for the target force of 15% and 30 % MVC compared to PPC and Sham groups in the right hand. In sequence blocks with left hand, this negative effect were found between M1-DLPFC and M1-Sham groups. In random blocks, no significant differences were found among four groups at each target forces for the left hand while there were significant differences for 15% (P =. 04) and 40% MVC (P =. 035) in the right hand. Our findings suggest that three different stimulation sites (DLPFC, M1 or PPC) were differentially affected by a single session of a-tDCS at some target forces during SVIPT. The effects of a-tDCS on ratio RT were transferred in the left untrained hand for sequence blocks but not random blocks. Further research is needed to understand fundamental aspects of these main areas of the brain on temporal processing in a precision control task such as SVIPT.

Proteins possess complex three-dimensional structures, and these structures are stable only within specific ranges of temperature which mostly correspond to the temperature ranges of the host organisms. However, few exceptional proteins, called heat-stable proteins, are stable at temperatures that are substantially higher than those tolerated by the host organisms themselves. Most of the heat-stable proteins possess heat stability to perform their functions at high temperatures, but some of them are intrinsically heat-stable due to their structure. Heat-stable proteins are usually divided into three or four groups depending upon the intricacies of their structures and thermal behaviors. Their peculiar property, i.e. heat-stability, makes them very valuable in applications such as polymerase chain reaction, industrial processes requiring high temperature, and protein engineering. Heat-stability also makes it feasible to purify such proteins, from the rest of the heat-labile proteins, using a simple heat-treatment method. Moreover, heat treatment can be used as a combined cell-lysis and protein purification step which, as compared to conventional methods, can result in a higher yield of heat-stable proteins. Furthermore, some special heat-stable proteins, i.e. intrinsically disordered proteins (which include the proteins involved in important neurodegenerative diseases), need heat-treatment step, in some cases, as the only way for their successful purification and study. Hence, this paper provides a first-ever comprehensive review of all major aspects of heat-stable proteins, i.e., their structure, evolution, classification, significance, and heat-treatment mediated purification.

Pakistan flora is enriched with potent bioactive compounds that must be explored while Alzheimer's disease (AD) poses a global challenge driven by neurochemical imbalances. Acetylcholinesterase (AChE) inhibitors traditionally alleviate symptoms, but addressing the root cause remains elusive. This gap has led to the exploration of herbal sources for interventions. In this context, we analyzed fifty 50 medicinal plants for their phytochemical composition and antioxidant and acetylcholinesterase inhibition activities. AChE activity was measured using Ellman’s method. Santalum album exhibited significant AChE inhibition (86.2%), surpassing galantamine hydrobromide (81.8%). Promising inhibition was also seen in Bombax ceiba (77.8%), Acacia karoo (52.9%), and Phaseolus lunatus (50.1%). Detailed analysis revealed Santalum album's abundance in terpenoids, flavonoids, tannins, and phenolics, potentially correlating with its antioxidant and AChE inhibitory effects. Acacia karoo demonstrated elevated levels of total alkaloids, antioxidants, terpenoids, and tannins. Both Acacia karoo and Santalum album show promise for AD intervention due to their AChE inhibitory activities and unique phytochemical attributes, warranting further exploration, particularly for Acacia karoo's novel potential in AChE inhibition, to advance targeted AD therapeutics utilizing natural resources. This study contributes to the search for effective AD strategies from nature's pharmacological resources.

With the development of energy internet, integrated energy system can effectively reduce carbon emissions and improve the utilization of renewable energy. In this paper, a low-carbon optimal scheduling model of integrated energy system considering heat loss of heat network pipeline is proposed. Based on the study of concentrating solar power (CSP) plant and heat storage tank (HS), an optimal scheduling model is established, which takes system operation cost, environmental pollution and penalty cost of abandoning wind and solar energy as objectives. Through the analysis of example results, it is proved that the model proposed in this paper can achieve the goal of reliable, low-carbon and economic operation of the system. At the same time, it shows that CSP unit can reduce the operation cost of system and increase energy coupling and utilization.

Cell-penetrating peptides (CPPs), a group of small peptides capable of promoting the transport of molecular cargo across the plasma membrane, have become important tools in promoting the cellular uptake of exogenously delivered macromolecules. GV1001, a peptide derived from a reverse-transcriptase subunit of telomerase (hTERT) and developed as a vaccine against various cancers, reportedly has unexpected CPP properties. Unlike typical CPPs, such as the HIV-1 TAT peptide, GV1001 enabled the cytosolic delivery of macromolecules such as proteins, DNA and siRNA via extracellular heat shock protein 90 (eHSP90) and 70 (eHSP70) complexes. The eHSP-GV1001 interaction may have biological effects in addition to its cytosolic delivery function. GV1001 was originally designed as a MHC class II-binding cancer epitope, but its CPP properties may contribute to its strong anti-cancer immune response relative to other telomerase peptide-based vaccines. Cell signaling via eHSP-GV1001 binding may lead to unexpected biological effects, such as direct anticancer or antiviral effects. In this review, we focus on the CPP effects of GV1001 bound to eHSP90 and ehsp70.

Sweat rate and electrolyte losses have a large inter-individual variability, a personalized approach to hydration can overcome this issue to meet an individual’s needs. This study aimed to investigate the effects of personalized hydration strategy (PHS) on fluid balance and intermittent exercise performance. Twelve participants conducted 11 laboratory visits including a VO2max test and two 5-day trial arms under normothermic (NOR) or hyperthermic (HYP) environmental conditions. Each arm began with 3-day of familiarization exercise following by two random exercise trials with a either PHS or control (CON). Then, participants crossed-over to the second arm for: NOR+PHS, NOR+CON, HYP+PHS, and HYP+CON. The PHS was prescribed according to participants’ fluid and sweat sodium losses. CON drank ad-libitum of commercially-available electrolyte solution. Exercise trials consisted of two phases: 1) 45min constant workload; 2) high-intensity intermittent exercise (HIIT) until exhaustion. PHS had a significantly greater fluid intake compared to CON. HYP+CON produced the lowest sweat sodium concentration. HYP+PHS had a lower thirst perception and a longer HIIT compared to HYP+CON. Thus, PHS reinforces fluid intake and successfully optimizes hydration status, regardless of environmental conditions. PHS may be or is an important factor to preventing negative physiological consequences during high-intensity exercise in the heat.

Heat using behavior has a large impact on in heating energy in heat metering system, and therefore a better understanding can assist in behavior guidance to reduce energy. To understand the current situation of indoor thermal environment and heat using behavior for heat metering households in northern China, including adjusting heating end valves and operating windows, 30 households were measured and surveyed. The factors influencing heat using behavior, including outdoor and indoor environmental parameters and time of the day, were analyzed. The results are :1) Thermal neutral temperature for heat metering households is relatively high, up to 24.5℃; 2) The heat using behavior of households is lack of rationality: low proportion of active households; high indoor temperature setting; more frequency of window opening. Improving indoor comfort is the main reason for households to adjust the heating end valve, and only 7.15% of households have considered the economic benefits brought by adjusting the valve. " Thermostat control valve does not work" is the main reason for households without adjustment; 3) Time of the day and indoor temperature affect active households’ willingness to adjusting heating end valve. Time of the day, indoor temperature and outdoor temperature have impacts on opening window during heating period.

Battery-powered electric vehicles (EVs) have emerged as an environmentally friendly and efficient alternative to traditional internal combustion engine vehicles, while their single-charge driving distances under cold conditions are significantly limited due to the high energy consumption of heating systems. Heat pumps can provide an effective heating solution for EVs, but their coefficient of performance (COP) is hampered by heat transfer deterioration due to frost accumulation. This study proposes a solution to this issue by introducing a microchannel heat exchanger (MHE) with superhydrophobic surface treatment (SHST) as a heat pump evaporator. A computational-fluid-dynamics MHE model and a dynamic heat pump model are developed and rigorously validated to examine the detrimental impact of frost accumulation on heat transfer, airflow resistance, and heat pump performance. When the frost layer thickness is 0.8 mm at a given air-side velocity of 1.0 m/s, the air-side heat transfer coefficient can be reduced by about 75%, and the air-side pressure drop sharply increases by 28.4 times. As frost thickness increases from 0 to 0.8 mm, the heating effect drops from 3.97 to 1.82 kW, and the system COP declines from 3.17 to 2.30. Experimental results show that the frost thickness of the MHE with SHST reaches approximately 0.4 mm after 30 minutes, compared to that of 0.8 mm of the MHE without SHST, illustrating the defrosting capability of the superhydrophobic coating. The study concludes by comparing the performance of various heating methods in EVs to highlight the advantages of SHST technology. As compared to traditional heat pumps, the power consumption of the proposed system is reduced by 48.7% due to the defrosting capability of the SHST. Moreover, the single-charge driving distance is extended to 327.27 km, an improvement of 8.99% over the heat pump without SHST.

Many microbes live in habitats below their optimum temperature. Retention of metabolic heat by aggregation or insulation would boost growth. Generation of excess metabolic heat may also provide benefit. A cell that makes excess metabolic heat pays the cost of production, whereas the benefit may be shared by neighbors within a zone of local heat capture. Metabolic heat as a shareable public good raises interesting questions about conflict and cooperation of heat production and capture. Metabolic heat may also be deployed as a weapon. Species with greater thermotolerance gain by raising local temperature to outcompete less thermotolerant taxa. Metabolic heat may provide defense against bacteriophage attack, by analogy with fever in vertebrates. This article outlines the theory of metabolic heat in microbial conflict and cooperation, presenting several predictions for future study.

This study examines the effects of particle size and heat pipe angle on the thermal effectiveness of a cylindrical screen mesh heat pipe using silver nanoparticles as the test substance. The experiment investigates three different particle sizes (30nm, 50nm, and 80nm) and four different heat pipe angles (0°, 45°, 60°, and 90°) on the heat transmission characteristics of the heat pipe. The results show that the thermal conductivity of the heat pipe increased with an increase in heat pipe angle for all particle sizes, with the highest thermal conductivity attained at a 90° heat pipe angle. Furthermore, the thermal resistance of the heat pipe decreased as the particle size decreased for all heat pipe angles. The thermal conductivity measurements of the particle sizes - 30, 50, and 80 nm - were 250 W/mK, 200 W/mK, and 150 W/mK, respectively. The heat transfer coefficient values for particle sizes 30nm, 50nm, and 80nm were 5500 W/m2K, 4500 W/m2K, and 3500 W/m2K, respectively. The study also found that the heat transfer coefficient increased with increased heat pipe angle for all particle sizes, with the highest heat transfer coefficient obtained at a 90° heat pipe angle.

Under the increasingly severe global heat threat, continuous high temperature has far-reaching effects on plant growth and development and become a major constraint to crop production. The development of heat-resistant varieties has become research hotspot in many fields, and it is also necessary to establish effective identification methods. In this study, twenty Brassica rapa varieties were selected to to investigate the physiological and biochemical characteristics under heat stress, explore the relationship between physiological response and the heat resistance mechanism, select some typical heat-resistant and heat-sensitive varieties. The effects of photosynthetic electron transfer and antioxidant pathway on heat resistance of Brassica rapa were identified. These findings will providing an important reference for the physiological regulation and identification method of high-temperature stress in plants.

Motivated by the well-known contradiction of special relativity and the heat equation, a wave equation for temperature scalar field is presented that also resolves the old controversy of (Lorentz) transformation of temperature and entropy. After showing that the current dogma of temperature and entropy being emergent concepts is based on but a logical fallacy, it is proposed that single particles posses entropy. This principle of fundamentality of entropy is then shown to be compatible with the equipartition theorem by yielding corrections in the quantum gravity regime.

High temperature (HT) significantly affects the crop physiological traits and reduces the 12 productivity in plants. To increase yields as well as survival of crops under HT, developing heat13 tolerant plants is one of the main targets in crop breeding programs. The present study attempted 14 to investigate the linkage of the heat tolerance between the seedling and the reproductive growth 15 stages of tomato cultivars ’Dafnis‘ and ’Minichal’. This research was undertaken to evaluate heat 16 tolerance under two experimental designs such as screening at seedling stage and screening from 17 reproductive traits in greenhouses. Survival rate and physiological responses in seedlings of 18 tomatoes with 4-5 true leaf were estimated under HT (40 °C, RH 70%, day/night, respectively) and 19 under two control and HT greenhouse conditions (day time 28 °C and 40 °C, respectively). Heat 20 stress significantly affected physiological-chemical (photosynthesis, electrolyte conductivity, 21 proline) and vegetative parameters (plant height, shoot fresh weight, root fresh weight) in all 22 tomatoes seedlings. The finding revealed that regardless of tomato cultivars the photosynthesis, 23 chlorophyll, total proline and electrical conductivity parameters were varied in seedlings during the 24 heat stress period. The heat tolerance rate of tomatoes in the seedling stage might not be associated 25 always with reproductive parameters. HT reduced the fruit parameters likeas fruit weight (31.9%), 26 fruit length (14.1%), fruit diameter (19.1%) and fruit hardness (9.1%) in compared to NT under HT 27 in heat susceptible tomato cultivar ‘Dafnis’, while in heat tolerant cultivar ‘Minichal’ fruit length 28 (7.1%) and fruit diameter (12.1%) was decreased by the affect of HT but on the contrary fruit weight 29 (3.6%) and fruit hardness (8.3%) were increased. In conclusion, screening and selection for tomatoes 30 should be evaluated at the vegetative and reproductive stages with consideration of reproductive 31 parameters.

This study investigates the long-term stability of the Suomi National Polar-orbiting Partnership (S-NPP) Visible Infrared Imaging Radiometer Suite (VIIRS) moderate-resolution Thermal Emissive Bands (M TEBs; M12 – M16) covering a period from February 2012 to August 2020. It also assesses inter-sensor consistency of the VIIRS M TEBs among three satellites-S-NPP, NOAA-20, and NOAA-21 over eight months spanning from March 18 to November 30, 2023. The field of interesting is limited to the ocean surface between 60°S and 60°N, specifically under clear-sky conditions. Taking radiative transfer modeling (RTM) as the transfer reference, we employed the Community Radiative Transfer Model (CRTM) to simulate VIIRS TEB brightness temperature (BTs), incorporating European Centre for Medium-range Weather Forecasts (ECMWF) reanalysis data as inputs. Our results reveal two key findings. Firstly, the reprocessed S-NPP VIIRS TEBs exhibit a robust long-term stability, as demonstrated through analyses of the observation minus background BT differences (O-B ∆BTs) between VIIRS measurements (O) and CRTM simulations (B). The drifts of the O-B BT differences are consistently less than 0.105 K/Decade across all S-NPP VIIRS M TEB bands. Notably, observations from VIIRS M14 and M16 stand out with drifts well within 0.04 K/Decade, reinforcing their exceptional reliability for climate change studies. Secondly, excellent inter-sensor consistency among these three VIIRS instruments is confirmed through the double-difference analysis method (O-O). This method relies on the O-B BT differences obtained from daily data. The mean inter-VIIRS O-O BT differences remain within 0.08 K for all M TEBs, except for M13. Even in the case of M13, the O-O BT differences between NOAA-21 and NOAA-20/S-NPP have values of 0.312 K and 0.234 K, respectively, which are comparable to the 0.2 K difference between some TEBs among VIIRS and MODIS. These disparities are primarily attributed to the significant differences in the Spectral Response Function (SRF) of NOAA-21 compared to NOAA-20 and S-NPP. Our study confirms the RTM-based TEB quality evaluation method’s versatility and effectiveness in assessing long-term sensor stability and inter-sensor consistency. The double-difference approach effectively mitigates uncertainties and biases inherent to CRTM simulations, establishing itself a robust mechanism for assessing inter-sensor consistency. In addition, we’ve observed that, except for M13, M12 always exhibits larger spatial variations of O-O BT differences with greater uncertainties compared to the other M TEBs. The influence of solar contribution through sea surface reflection on the Top of Atmosphere (TOA) radiance measurements during daytime in M12 should not be underestimated.