In order to establish the formation patterns of the Co–Mg oxide system, samples with different Co:Mg ratios and heat treatment temperatures were synthesized and studied. Study of the sam-ples confirmed the phase transition of MgxCo2–xO4 spinels into corresponding solid solutions at 800–900 °C. The similarity of formation patterns for different compositions is shown. The rock-salt oxide in low-temperature samples is an anion-modified paracrystalline phase that forms a “true” solid solution only upon spinel decomposition. TPR profiles of decomposed Co3O4 spinel show surface Co3O4 peaks and a wide peak corresponding to well-crystallized CoO, while par-tial Co3O4 TPR up to 380 °C results in dispersed and amorphous CoO. High-temperature non-stoichiometric samples are poorly reduced, indicating their low oxygen reactivity. Spinel reoxidation after heat treatment to 1100 °C by calcination at 750 °C showed complete regenera-tion for MgCo2O4–Co3O4 samples and its absence in case of an excess of MgO relative to stoi-chiometry. Based on the data obtained, it can be concluded that the processes governing the formation of Co–Mg oxide systems are determined by both Co:Mg ratio and the heat treatment conditions, potentially providing the possibility of fine tuning for specific catalytic processes.

Demand for environmentally friendly types of energy is growing all over the world, which naturally increases the intensity of work on the production of hydrogen-containing fuel mixtures. Steam reforming of methanol is one of the most effective areas of research, as it is a process with low energy consumption. The results of steam reforming of methanol on the catalysts prepared by solution combustion synthesis (SCS) and impregnation by moisture capacity are presented. Investigation of the activity of Cu-Ce-Al catalysts of different composition was carried out for production of hydrogen and comparison of SCS with traditional impregnation method. Methanol conversion reaches 99%, while the selectivity of H2 was 88%, at 500 °C. It was found that CuAl2O4 spinel formation is due to substitution of Al3+ with Cu2+ Ce3+ cations. A consequence CuAl2O4 and CeAlO3 lattice parameters increase because of difference in ionic radius of Al3+ (0.53 Å) and Cu2+ (0.73 Å), Ce3+ (1.07 Å). Advantages of SCS catalysts in steam reforming of methanol were shown. The aim of this research is to develop a new catalyst for conversion of methanol into hydrogen containing fuel mixtures, which will further promote the organization of a new era of environmentally friendly energy-saving production methods.

In this work, dry and hydrothermal carbonization (DC and HTC) of RDF pellets were conducted to evaluate the physical, chemical, and fuel properties of the produced chars. In the dry carbonization tests, biomass sawdust was incorporated in different proportions on the samples to minimize agglomeration caused by the melting of the plastic fraction. The experiments were carried out in a temperature of 400°C (DC) and 250-300°C (HTC), in a residence time of 30 minutes. The respective chars and hydrochars were characterized according to their mass yield, apparent density, proximate, elemental, and mineral composition, chlorine content, high heating value, thermogravimetric profile, and surface functional groups. The results showed that dry carbonization of RDF pellets with biomass incorporation, followed by a washing step, resulted in the production of chars with improved properties such as higher fixed carbon and HHV (25-26 MJ/kg) and lower ash and chlorine content. Additionally, the HTC experiments demonstrated that hydrochars showed improved properties without the need for biomass addition and washing, however, with no significant difference in the HHV (20-21 MJ/kg). Therefore, DC of RDF pellets with 10% biomass incorporation seems to be a promising option to overcome the constraints of RDF utilization as an alternative fuel.

Maritime data not only identify financial resources that can significantly enhance the efficiency of shipping companies but also play a pivotal role in promoting eco-friendly and sustainable shipping practices. However, active corporate strategies are required to include maritime data essential for the commercial operation of autonomous ships in the form of corporate assets by transparent evaluating the data. The aim of this study is to review previous studies on da-ta-valuation models, identify a valuation model suitable for maritime business, consider the characteristics of maritime data. The analytic hierarchy process (AHP) method is used to derive priorities for valuing maritime data assets, with emphasis placed on the characteristics of mari-time data, followed by the character of the future-oriented maritime-data market and the da-ta-valuation model. The results obtained that the most important factors in selecting a maritime data-valuation model by analyzing the AHP method were identified as the characteristics of the maritime data(M1). The next most important factors analyzed were the features of the mari-time-data market(M2) and the features of the maritime data-valuation model(M3) in order. In addition, the characteristics of maritime data were preferentially considered among the main criteria, and the market approach (A2) was selected as the most optimal valuation model. The potential impact of this implementation could contribute to the establishment of an intelligent technology market by estimating the value of data and developing a platform for maritime data trading, allowing for more efficient data sharing and utilization by maritime autonomous sur-face ship(MASS).

A better understanding of high temperature processes in slags contributes to facilitate knowledge based design of the solidified product. Here, a slag analogue with a nominal composition of 17 wt% LiMnO2 and 83 wt% Ca2SiO4 was synthesized encountering fairly high cooling rates. The Mn species from 1223 K to 1773 K was simulated using a thermodynamic model assuming a homogeneous melt. The micro-composition including the Mn species of the solidified slag was determined experimentally and was used as basis for molecular dynamics (MD) simulation. The MD simulation provides information on structure and viscosity at high temperatures, otherwise difficult to access. These parameters significantly influence oxidation state of redox-active elements and the solidified product. The micro-composition analyzed by electron probe micro analysis (EPMA) and synchrotron based micro-X-ray fluorescence (micro-XRF) showed that Mn-rich and Ca-Si-rich phases are separated. While the Mn-O phases did not contain noticeable Ca, the Ca2SiO4 phase had incorporated 0.6 wt% of Mn. The slag solidified into round shaped and droplet shaped grains of a Li-Mn-oxide, some Mn3O4 and Ca2SiO4. The powder X-ray diffraction (PXRD) confirmed the formation of larnite, the identity of the Li-Mn-oxide however remained inconclusive. The Mn oxidation state (OS) was identified using synchrotron based micro-X-ray absorption near edge spectroscopy (micro-XANES). The Mn-O grains, matched well with Li-Mn-oxides and a Mn OS: +3 e.g. LiMn3+O2. Small areas matching Hausmannite (Mn2+Mn23+O4) were also identified. The OS of Mn in the silicate phase could not be identified. For comparison a slowly cooled slag analogue with similar composition however higher Si content, was also subjected to micro-XANES. The slowly cooled slag formed long Mn-rich needles in a matrix of large calcium silicate crystals. The Mn-rich crystals matched well with the XANES spectrum of a Mn3+ Li-oxide like LiMn3+O2. At the rim of the needles the Mn-spectra matched well the Hausmannite (Mn2+Mn23+O4) reference. In the silicate phases Mn had a OS: +2, unambiguously. The melt structure at different temperatures of two compositions i.e. LiMn3+O2 and Ca2SiO4 was simulated using molecular dynamics (MD). They serve as model compositions assuming a heterogeneous melt. The results show significant different degrees of polymerization and viscosity. Information from MD simulations can support the identification of potentially different oxygen permeability and with that prediction of oxidation states. The bulk composition was identified by inductively coupled plasma optical emission spectrometry (ICP-OES), bulk structure by PXRD and bulk species by lab-XANES. The synchrotron micro analysis including micro-XRD were performed at the microfocus beamline I18 at the Diamond Light Source. Pure reference compounds were prepared and characterized with the same multi-modal approach.

The high dependence on light crude oil as the main source of energy in automobiles., industrial processes, source of raw material for various industrial synthesis have made the heavy crude more available in the world and open for research work on its potentials as a source of energy for the increasing population of the world in areas like energy source for powering big marine engines, energy source in heavy industrial machines e.t.c. Though the relatively unfavourable characteristics of heavy fuel oil such as; high viscosity, high probability of precipitating is a reasonable challenge to the possible utilization of heavy fuel as a source of energy in the areas highlighted above. These issues of heavy fuel oil are largely due to the presence of Asphaltene in it which is a large complex hydrocarbon in heavy fuel oil. Understanding the combustion potential of asphaltene is therefore an interesting and challenging problem that has attracted increasing attention from both academia and industry. This research work is aimed at carrying combustion studies on the Forcados (Ni-geria) heavy fuel fraction asphaltene HFFA extracted from Forcados crude Oil and examining its combustion characteristics with the view to examine it for future sweet heavy fuel generation for it source got low sulphur content, to ascertain the volatile composition, moisture and ash content. The HFFA extracted to determine physical characteristics of the HFFA extracted for fuel properties potentialities and this study was carried out to evaluate the chemical constituents of forcadous asphaltene lead-ing to the generaration of HFFA using GCMS. The Forcados asphaltene showed some good fuel properties when subjected to ce-tane number, API gravity, flash point and cloud point parameter test. Probing further with AAS for trace metal presence showed some high concentration on Chromium (Cr), Nickel (Ni), Iron (Fe), Lead (Pb), Cadmium (Cd), Copper (Cu), Manganese (Mn) and Zinc (Zn) indicating the potential for residual and soot formation after combus-tion. But still being a sweet asphaltene from Nigerian sweet crude source will be de-void of corrosive effect on machineries and heavy fuel engine if used to power it as in the case of high sulphur content in Venezuelan crude oil and some other world. The GCMS showed the decomposition of heavy crude asphaltene peaks and sig-naling the presence of heavy fuel fraction in the composition of the asphaltene while the FTIR and the UV-VIS identified the various functional groups in the compounds and the identification of signals that cannot be seen in the normal spectrum respec-tively.

The variation of aerosols, especially dust aerosol, in time and space plays an important role in climate forcing studies. Aerosols can effectively reduce land surface longwave emission and re-emit energy at a colder temperature, making estimation of downwelling surface longwave radiation (DSLR) with satellite data difficult. Using the latest atmospheric radiative transfer code (MODTRAN 5.0), we simulate the outgoing longwave radiation (OLR) and DSLR under different land surface and atmospheric profile conditions. The results show that dust aerosol has an obvious “warming” effect to longwave radiation compared with other aerosols, that aerosol longwave radiative forcing (ALRF) increased with increasing aerosol optical depth (AOD), and that the atmospheric water vapor content (WVC) is critical to the understanding of ALRF. A method is proposed to improve the accuracy of DSLR estimation from satellite data for the skies under heavy dust aerosols. The AOD and atmospheric WVC under cloud-free conditions with a relatively simple satellite-based radiation model that yields the high accurate DSLR under heavy dust aerosol are used explicitly as model input to reduce the effects of dust aerosol on the estimation of DSLR. Validations of the proposed model with satellites data and field measurements show that it estimates the DSLR accurately under heavy dust aerosol skies. The root mean square errors (RMSEs) are 20.4 W/M² and 24.2 W/M² for Terra and Aqua satellites, respectively, at the Yingke site, and the biases are 2.7 W/M² and 9.6 W/M², respectively. For the Arvaikheer site, the RMSEs are 23.2 W/M² and 19.8 W/M² for Terra and Aqua, respectively, and the biases are 7.8 W/M² and 10.5 W/M², respectively. The proposed method is especially applicable to acquire relatively high accurate DSLR under heavy dust aerosol using MODIS data with available WVC and AOD data.

Heavy metal pollution poses a significant threat to ecosystems and human health worldwide. In response to this pressing issue, bioremediation has emerged as a promising approach for mitigating contamination. This paper adopts a bibliographic method to explore the key techniques and applications of bioremediation. Furthermore, we delve into the most prominent threats to human environmental health and the corresponding remediation methods. Additionally, we discuss the future trajectory of bioremediation research, with a particular focus on the integration of big data and machine learning technologies. These advanced methodologies hold great potential for enhancing the effectiveness and efficiency of environmental remediation efforts in the face of escalating pollution challenges.

Intermediate temperature solid oxide fuel cell (SOFC) operation provides numerous advantages such as high combined heat and power (CHP) efficiency, potentially long-term materials stability, and the use of low-cost materials. However, due to the sluggish kinetics of the oxygen reduction reaction at intermediate temperature, the cathode of SOFC requires an efficient and stable catalyst. Significant progress in the development of cathode materials has been made over recent years. In this article, multiple strategies for improving the performance of cathode materials have been extensively reviewed such as A and B site doping of perovskites, infiltration of catalytic active materials, the use of core-shell composites, etc. Emphasis has been given to intrinsic properties such as thermal expansion compatibility, chemical and thermal stability, and oxygen transport number. Furthermore, to avoid any insulating phase formation at the cathode/electrolyte interface, strategies for interfacial layer modifications have also been extensively reviewed and summarized. Based on major technical challenges, future research directions have been proposed for efficient and stable intermediate temperature solid oxide fuel cell (SOFC) operation.

Improper disposal of waste plastic has caused serious ecological and environmental pollution problems. Transforming plastics into high value-added chemicals can not only achieve efficient recycling of waste plastics, but also an effective way to control white pollution. The catalyst selectively breaks the C-C bond of polyolefin plastic under heat treatment and converts it into liquid fuel, thus realizing sustainable recycling of plastics and has a good development prospect. This review provides a detailed overview of the current development of catalytic pyrolysis, catalytic hydrolysis, solvent decomposition and supercritical hydrothermal liquefaction for cracking plastics to make fuel oil. The reaction mechanism, influencing factors and promoting effects of catalysts in various degradation technologies are analyzed and summarized and the latest proposed tandem reaction for degrading plastics is briefly introduced. Finally, some optimization paths of waste plastic pyrolysis to fuel oil technology are proposed: synergies between mixed raw materials, in-depth exploration of catalysts, design and manufacture of reactors that match the pyrolysis technology. All these are important research directions for promoting the industrialization of plastic pyrolysis to fuel oil.

Graphene hybrid-filler polymer composites have emerged as prominent materials that revolutionize heavy industries. This study encapsulates the in-depth analysis of different influential factors such as filler/graphene type, aspect ratios, dispersion methods, filler-matrix compatibility, fiber orientation, synergistic effects, different processing techniques, and post-curing conditions that affect the processing, properties and determine the resultant applications of graphene hybrid polymer composites. Additionally, it discusses the substantial role of graphene collaboration with other fillers such as carbon nanotubes, silica, nano-clays and metal oxides to produce functionalized hybrid polymer composites with synergistically enhanced tailored properties to offer solutions for heavy industries like aerospace, automotive, electronics, and energy harvesting. The review concludes with some suggestions and outlook on the future of these composite materials by emphasizing the need for continued research to fully optimize their potential.

Phased injection of natural gas into internal combustion marine engines is a promising solution for optimizing performance and reducing harmful emissions, particularly unburned methane, a potent greenhouse gas. This innovative practice distinguishes itself from continuous injection because it allows for more precise control of the combustion process with only a slight increase in system complexity. By synchronizing the injection of natural gas with the intake and exhaust valve opening and closing times while also considering the gas path in the manifolds, methane release into the atmosphere is significantly reduced, making a substantial contribution to efforts to address climate change. Moreover, phased injection improves the efficiency of marine engines, resulting in reduced overall fuel consumption, lower fuel costs, and increased ship autonomy. This technology has been tested on a single-cylinder, large-bore, four-stroke research engine designed for marine applications, operating in dual-fuel mode with diesel and natural gas. Performance was compared with that of the conventional continuous feeding method. Evaluation of the effect on equivalent CO2 emissions indicates a potential reduction of up to approximately 20%. This reduction effectively brings greenhouse gas emissions below those of the diesel baseline case, especially when injection control is combined with supercharging control to optimize the air-fuel ratio.

Multi-rotor drones, a kind of unmanned equipment which is widely used in military, commercial consumption and other fields, has been developed very rapidly in recent years. However, their short flight time has hindered the expansion of their application range. This can be addressed by utilizing hydrogen fuel cells, which exhibit high energy density, strong adaptability to ambient temperature, and no pollution emissions, as the power source. Accordingly, the application of hydrogen fuel cells as the power source in multi-rotor drones is a promising technology that has attracted significant research attention. This paper summarizes the development process of hydrogen fuel cell mul-ti-rotor drones and analyzes the key obstacles that need to be addressed for the further development of hydrogen fuel cell multi-rotor drones, including structural lightweight, hydrogen storage methods, energy management strategies. Additionally, prospects for the future development of hydrogen fuel cell multi-rotor drones are presented.

Automated charging technologies are becoming increasingly important in the electrification of heavy road freight transport, especially in combination with autonomous driving. This study provides a comprehensive analysis of automated charging technologies for electric heavy-duty vehicles (HDVs). It encompasses the entire spectrum of feasible technologies, including static and dynamic approaches, with each charging technology evaluated for its advantages, potentials, challenges, and technology readiness level (TRL). Static conductive charging methods such as charging robots, underbody-couplers or pantographs show good potential, with pantographs being the most mature option. These technologies are progressing towards higher TRLs, with a focus on standardization and adaptability. While static wireless charging is operational for some prototype solutions, it encounters challenges related to implementation and efficiency. Dynamic conductive charging through an overhead contact line or contact rails holds promise for high-traffic HDV routes with the overhead contact line being the most developed option. Dynamic wireless charging, although facing efficiency challenges, offers potential for seamless integration into roads and minimal wear and tear. Battery swapping is emerging as a practical solution to reduce downtime for charging, with varying levels of readiness across different implementations. To facilitate large-scale deployment further standardization efforts are required. The study emphasizes the necessity for continued research and development to enhance efficiency, decrease costs, and ensure seamless integration into existing infrastructures. Technologies that achieve this best will have the highest potential to significantly contribute to the creation of an efficiently automated and environmentally friendly transport sector.

Diesel is consistently a very popular fuel for internal combustion engines. Its consumption in the European Union has been rising over recent years, as has the number of engines increasingly sensitive to fuel contamination. One of the most important parameters affecting diesel quality is water content. Although its exceedances of the standard’s permissible amount are not common, they carry the risk of serious damage to expensive, modern fuel injection systems. Current methods of measuring water content require both specialised personnel and equipment, as well as transporting the sample to a suitable laboratory. The research presented in this paper was aimed at verifying whether it would be possible to test the moisture content of diesel using impedance spectroscopy. Once refined, such measurement method could be used in situ. Analysing the properties of diesel is challenging, mainly because many types of the fuel are sold, the chemical composition of which is always a well-guarded manufacturer’s secret. The experimental results obtained on many types of commercially available diesel show that it is possible to use impedance spectroscopy to estimate the water content of different types of diesel fuel. The measurement accuracy achieved makes it possible to detect approaching or exceeding the permissible water content.

A dioxomolybdenum catalyst [(MoO2Cl2-O-MoO2Cl2)(L)] (1) (with L (1S,2S)-N,N´-bis(2-pyridinecarboxamide)-1,2-cyclohexane) was prepared and used as catalyst for the desulfurization of a multicomponent model fuel containing the most refractory sulfur compounds in real fuels. This complex showed to have a high efficiency to oxidize the aromatic benzothiophene derivative compounds present in fuels, mainly using a biphasic 1:1 model fuel/MeOH system. This process conciliates catalytic oxidative and extractive desulfurization, occurring the oxidation of the sulfur compounds in the polar organic solvent. The oxidative catalytic performance of (1) showed to be influenced by the presence of water in the system. Using 50% aq. H2O2 it was possible to reuse the catalyst and the extraction solvent MeOH during ten consecutive cycles without loss of desulfurization efficiency.

In this paper, I introduce a new concept of representing numbers in base ; in other words, I have found new series for any number similar to series that could be written according to the collatz sequence which is called zi(n) in this article. These series need to end with 1. Then, we use two sets of rules to make a diagram which then proves the existence of such series for any number.In this diagram, by branching numbers into different branches in accordance to the modularity of 4 and continuing branching to the point that their numbers have enough common terms in their collatz series, we could reduce zi(n) to zi(k) so that k<n in any branch by Rule Number One. This diagram shows that zi(n) exists for every number, in other words, this proves the theorem (A) or zi-existence theorem. The proof of zi-existence theorem leads to a proof of the collatz conjecture because the collatz series could be written as a linear combination of such series that all of them end with 1, so the collatz series for any number ends with 1.

Pollution, urbanization and technological advancements have posed stress on the ecosystem and its matrices. Globally, pollutants are observed in all compartments of ecological communities which affect the integrity of the atmosphere, hydrosphere, lithosphere and biosphere. Xenobiotics bioaccumulate and biomagnify across trophic levels or webs. Heavy metals have been implicated in impacts towards biodiversity and environmental declination. In Nigeria, wastes issues are a cause of concern and landfilling or are waste disposal approaches that cause deleterious effects such as depauperation of diversity and species decline, prompting the non-invasive ecotoxicological hazard assessments. Feathers were used to assess concentration levels of 13 metals (Fe, Mn, Zn, Cu, Co, Cr, Cd, Pb, Ni, Al, B, Se and Hg) using fast atomic absorption spectrophotometer (FAAS), one-way ANOVA was used in comparing variations in mean concentrations across trophic levels, diversity indices and point count methods were used to estimate diversity and abundance. Four avian species were assessed Hirundo aethiopica (insectivore), Streptoptelia senegalensis (granivore), Turdus pelios (omnivore), and Anthus leucophrys. (insectivore). Observed concentrations of important metals like iron were high with the insectivores having the highest concentrations of iron (2.6985 ± 0.1975 ppm) and granivores having the lowest (2.0100 ± 0.3172 ppm). The insectivores had the highest concentrations for cadmium, cobalt and chromium (0.0005 ± 0.0005ppm), nickel (at 00.0012 ± 0.0017 ppm) and least was observed in the granivores (0.0003 ± 0.0006 ppm). Selenium concentrations were quite high in insectivores (0.0775 ± 0.0035 ppm) and lowest in granivores (0.0433 ± 0.0015 ppm) likewise mercury for insectivores (0.0280 ± 0.0010 ppm) and granivores (0.0213 ± 0.0015 ppm). From the study, it is apparent that landfills are sources of pollution and poor management of wastes can affect biota (causing effects such as asymmetry and bioaccumulation) and ecosystem balance. The observation of heavy metals in the feathers serve as good sentinels due to their trophic levels and could be signs for what could be yet to occur. The heavy metal concentrations were significantly different at p < 0.05.

As marine traffic is contributing to pollution and mostly have predictable route with repetitive load profiles, to reduce their impact on environment, hybrid system with proton exchange membrane fuel cells (PEMFC-s) and battery pack, is promising replacement. For this purpose, the numerical model of repowered existing vessel that have two diesel engines with 300 kWe is developed. The goal of this paper is to develop numerical model which analyzes and determine equivalent hybrid ship propulsion system for known traveling route. The developed numerical model consists of an interconnected system with PEMFC stack and battery pack as power sources. Numerical model is developed and optimized to meet minimal required power demand for successful route demand, which has variable loads and daily sails six-time same voyage- in total 54 nautical miles. The results have shown that equivalent hybrid power system consists of 300 kWe PEMFC stack and battery pack with 424 kWh battery and state of charge varying between 20 and 87%. To power this new hybrid power system, hydrogen tank of 7200 l holding 284.7 kg at pressure of 700 bar is needed, compared to previous system that spend 1524 kg of diesel and generate 4886 kg of CO2.

This study aims to examine the non-volatile Particle Number (PN) emissions of a retrofitted Heavy-Duty Spark-Ignition (HD-SI) engine powered by liquefied petroleum gas (LPG) under both steady-state and transient conditions. The engine was tested under seven steady-state operating points to investigate the PN behavior and Particle Size Distribution (PSD) upstream and down-stream of the Three-Way Catalyst (TWC). This analysis intends to assess the impact of including particles with diameters ranging from 10 nm to 23 nm in the total particle count, a consideration for future regulations. The study employed the World Harmonized Transient Cycle (WHTC) for transient conditions to encompass the same engine working region used in the steady-state analysis. A Dekati FPS-4000 diluted the exhaust sample to measure the PSD and PN for particle diameters between 5.6 nm and 560 nm using the TSI-Engine Exhaust Particle Sizer (EEPS) 3090. Findings indicate that PN levels tend to increase downstream of the TWC under steady-state conditions in operating points with low exhaust gas temperatures and flows (equal to or less than 500 °C and 120 kg/h). Furthermore, the inclusion of particles with diameters between 10 nm and 23 nm leads to an increase in PN emissions by 17.70% to 40.84% under steady conditions and by an average of 40.06% under transient conditions, compared to measurements that only consider particles larger than 23 nm. Notably, in transient conditions, most PN emissions occur during the final 600 seconds of the cycle, linked to the most intense phase of the WHTC.

Addressing the pressing challenge of global warming, reducing greenhouse gas emissions in the transportation sector is a critical imperative. Battery and fuel-cell electric vehicles have emerged as promising solutions for curbing emissions in this sector. In this study, we conducted a comprehensive life cycle assessment (LCA) for typical passenger vehicles, heavy duty trucks and city buses using either proton-exchange membrane fuel cells or Li-ion batteries with different cell chemistries. To ensure accuracy, we supplemented existing studies with data from the literature, particularly for the recycling phase, as database limitations were encountered. Our results highlight that fuel cell and battery systems exhibit large emissions in the production phase. Recycling can significantly offset some of these emissions, but a comparison of the technologies examined revealed considerable differences. Overall, battery electric vehicles consistently outperform fuel cell electric vehicles regarding absolute greenhouse gas emissions. Hence, we recommend prioritizing battery electric over fuel cell vehicles. However, deploying fuel cell electric vehicles could become attractive in a hydrogen economy scenario where other factors, e. g. the conversion and storage of surplus renewable electricity via electrolysis, become important.

Underwater visual detection technology plays a pivotal role in fields such as marine exploration. With the increasing demand for underwater monitoring, the quest for efficient and reliable methods for underwater target recognition has become particularly significant. To address this requirement, this study developed an innovative underwater object detection architecture based on YOLOv8, named YOLOv8-MU, aimed at significantly enhancing detection accuracy.By integrating the LarK module proposed in UniRepLKNet to optimize the backbone network, YOLOv8-MU aims to achieve a larger receptive field without increasing the model’s depth. Further, this research introduces C2fSTR, an innovative method that combines Swin Transformer with the C2f module. Additionally, we have incorporated the SPPFCSPC_EMA module, which combines Cross-Stage Partial Fast Spatial Pyramid Pooling (SPPFCSPC) with attention mechanisms, significantly improving the detection accuracy and robustness of various biological targets. Moreover, by introducing a fusion block based on DAMO-YOLO into the neck of the model, we further enhanced the model’s capability in multi-scale feature extraction. Finally, the adoption of the MPDIoU loss function, designed around vertex distance, effectively tackles the challenges of localization accuracy and boundary clarity in underwater organism detection. Experimental results on the URPC2019 dataset demonstrate that the YOLOv8-MU model achieved an [email protected] of 78.4%, marking improvements of 5.6%, 1.1%, and 4.0% over YOLOv5s, YOLOv7, and YOLOv8n respectively, indicating the leading performance (SOTA) of this method. On the other hand, further evaluation on the URPC2020 dataset confirmed the generalization capability of the YOLOv8-MU architecture, with its [email protected] reaching 80.4%, surpassing various models including YOLOv5x and YOLOv8n, showcasing the wide applicability of our proposed improved model architecture.

The study of biologically active substances from natural sources shows the prospect of obtaining a new type of antimicrobial agents, highly effective against pathogenic microorganisms and non-toxic to humans. Our study reveals for the first time that Cornu aspersum mucus has the potential to act as a source of antibacterial agents against bacterial pathogens such as Bacillus cereus 1085, Propionibacterium acnes 1897, Salmonella enterica 8691, Enterococcus faecalis 3915, and Enterococcus faecium 8754. Both mucus fractions with MW<20 kDa and MW>20 kDa showed antimicrobial activity and antioxidant properties that’s why they can be turned into an alternative agent to expensive synthetic antibacterial compounds. Using de novo sequencing 16 novel peptides with potential antibacterial activity were identified by in a fraction with MW<20 kDa. The results of electrophoretic and proteomic analysis of mucus fraction with MW >20 kDa presented proteins with potential antibacterial activity highly homologous to hemocyanins, mucus protein Aspernin, lectins, L-amino acid oxidase-like protein, and mucins (mucin-5AC, mucin-5B, mucin-2 and mucin-17). Thanks to the synergistic action of the bioactive components, the mucus fraction with MW > 20 kDa in low concentrations per 8–2 µg/mL showed promising antimicrobial activity against the tested bacteria, comparable to Vancomycin and without unwanted cytotoxic effects against non-target cells. Additionally, C. aspersum mucus fractions were found to have a positive effect on eukaryotic organisms by reducing the levels of intracellular oxidative damage and increasing the antioxidant capacity of the cell. These findings could serve as a basis for the development of a potent non-cytotoxic antibacterial agent to replace conventional antibiotics and avoid the development of antibiotic resistance.

Surface activity of humic acid (HA) and its six sub-fractions isolated from forest soil were characterized by surface tension measurements, dynamic light scattering, and laser doppler electrophoresis. The surface tension of HA sub-fractions decreased from 72.4 mN·m-1 to 36.8 mN·m-1 with the increasing concentration from 0 to 20000 mg·L-1. The critical micelle concentration (CMC) of HA and its sub-fractions ranged from 216 to 1024 mg·L-1 with the multiple linear regression equation of CMC = 18896–6.9×C–296×alkyl-C–331×aromatic-C–17019×H/C+4054×HB/HI (p &lt; 0.05). The Z-average particle size ranges from 108.2 nm to 186.9 nm. The maximum particle size was 5000 nm after filtered with a membrane of 0.45 μm, indicating HA and its sub-fractions progressed self-assembly during 2000 mg·L-1, pH = 6.86. The number-base particle size distribution of HA sub-fractions was identified as four peaks by Gaussian model, and the aggregate sizes were mainly in six clusters including 2 ± 1 nm, 5 ± 2 nm, 10 ± 3 nm, 21 ± 8 nm, 40 ± 10 nm, and &gt; 50 nm indicating multiple aggregations of different particle sizes in the HA fractions solution.

This work aims to investigate the effect of process temperature and catalyst content by thermochemical degradation of municipal solid waste (MSW) fraction (organic matter + paper + plastic) on the yield of reaction products (bio-oil, biochar, H2O and gas), physicochemical properties and chemical composition of bio-oils, as well as on the morphology and crystalline phases of biochar in laboratory scale. The organic matter, paper and plastic segregated from the gravimetric composition of total waste sample were subjected to the pre-treatments of drying, crushing and sieving. The experiments were carried out at 400, 450 and 475 °C and 1.0 atmosphere, and at 450 °C and 1.0 at-mosphere, using 5.0, 10.0 and 15.0% (wt.) of FCC zeolite, bath mode, using a laborato-ry scale glass reactor. The bio-oil was characterized for acidic value. The chemical functions present in the bio-oil identified by FT-IR and the composition by GC-MS. Biochar was characterized by SEM/EDS and XRD. Thermal pyrolysis of the MSW frac-tion (organic matter + paper + plastic) shows bio-oil yields between 9.44 and 9.24% (wt.), aqueous phase yields between 21.93 and 18.78% (wt.), solid phase yields between 67.97 and 40.34% (wt.) and gas yields between 28.27 and 5.92% (wt.). The yield of bio-oil decreases with increasing process temperature. For the experiments using FCC, the biochar and gas yields increase slightly with the FCC content, while that of bio-oil de-creases and the H2O phase remains constant. The GC-MS of bio-oils identified the presence of hydrocarbons and oxygenates, as well as nitrogen-containing compounds, including amides and amines. The acidity of the bio-oil increased with increasing temperature and with the aid of FCC as a catalyst. It has been identified the presence of hydrocarbons within bio-oil by addition of FCC catalyst due to the deoxygenation of carboxylic acids, followed by decarboxylation and decarbonylation reactions, producing aliphatic and aromatic hy-drocarbons.

Very heavy stratiform precipitation (> 200 mm/per day) occurred in the Hokitika region on the west coast of the South Island of New Zealand on 18 June 2015, under north-westerlies with small CAPE (< 25 J/kg). Analyses of model simulations and observations showed that this heavy rainfall was due to cold front lifting enhanced by orographic lifting over the Southern Alps. At 1.5 km grid-length, the model terrain underestimated the average height of the 103 tallest mountains over the South Island by ~ 800 m. This leads to weaker orographic lifting and mountain blocking, and a faster-moving and stronger cold front in the Hokitika region. As a result, large errors in the heavy rainfall prediction occur. By increasing either the resolved or the sub-grid mountain heights, the simulated rainfall errors were largely reduced through stronger orographic lifting and mountain blocking, and a better simulation of the cold front movement and strength. All the experiments have the same “flow-over” regime with mountain waves and/or wave breaking (Fm ranges 0.61 – 1.21). However, the rainfall amount and distribution on the windward side of mountains altered significantly. Our new findings were that the Southern Alps can have significant indirect effects on heavy rainfall by altering the speed and strength of the cold front, in addition to the well-known direct dynamical effects (i.e., orographic lifting and mountain blocking). A combination of these direct and indirect effects makes the heavy rainfall simulation sensitive to mountain heights even under the same “flow-over” regime.

This paper reviews the requirements for the production, quality, and quality assurance of solid recovered fuels (SRF) that are increasingly used for the substitution of fossil fuels in the indus-trial utilities. The economical, technological and environmental aspects should be considered before using SRF as an alternative fuel. In general, the most important factors determining the commercial production of SRF referred to the calorific values and their available amounts adopted in the starting materials. Furthermore, the low-melting impurities and undesired constituents/elements, including chlorine, sulfur, potassium and sodium, may pose negative impacts on air pollutant emission and slagging & fouling in the process utilities. In this regard, the vent emitted from the industrial utilities must comply with the effluent standards of station-ary sources like particulate, sulfur oxides, nitrogen oxides, heavy metals (e.g., lead, cadmium, and mercury) and dioxins. For these reasons, this work will summarize the legal or regulatory requirements under development in Asian countries (i.e., Japan, South Korea, and Taiwan) and European Union (EU). Finally, the outlook of solid recovered fuel (SRF) in the waste manage-ment and industrial sectors will be addressed to echo the sustainable development goals (SDGs).

Heavy metal accumulation in soils used for agricultural purposes is a major issue as it can affect the growth of plants and contain health risks as plants containing heavy metals are taken as food. This study provided the potential of three Bacillus pumilus strains (C-2PMW-8, C-1 SSK-8, and C-1PWK-7) for mitigation of the health factors related to heavy metals on lettuce (Lactuca sativa) grown in chromium contaminated soil from activities related to mining. Lettuce seeds inoculated with B. pumilus strains were grown in pots with garden soil amended with varying amount of chromite mine soil (2.27%, 4.65%, 7.14%). Growth indicators like days to germination, percentage of germination, leaf weight, leaf area and rate of survival decreased with incremental soil chromium levels but improved highly with inoculation of B. pumilus compared to uninoculated controls. When B. pumilus strains were provided, there was also a decreased level in the buildup of chromium in soil as well as lettuce shoots. The results explains that plant growth-promoting B. pumilus strains may be able to lower down the detrimental effects of chromium on lettuce development, hence increment in the effectiveness of phytoremediation.

Background: Optimal hypofractionated schedule of post-prostatectomy radiotherapy remains to be established. We evaluated treatment outcomes and toxicity of the moderately hypofractionated post-prostatectomy radiotherapy in 16 daily fractions delivered with IMRT/VMAT. The treatment schedule selection was motivated by limited technology resources. Methods: One hundred consecutive M0 patients with post-prostatectomy radiotherapy were evaluated. Radiotherapy indication was adjuvant (ART) in 19%, early salvage (eSRT) in 46% and salvage (SRT) in 35%. The dose prescription for prostate bed PTV was 52.8 Gy in 16 fractions of 3.3 Gy. The Common Terminology Criteria v.4 for Adverse Events scale was used for toxicity grading. Results: The median follow-up was 61 months. Five-year biochemical recurrence-free survival (bRFS) was 78.6%, distant metastases-free survival was 95.7% and overall survival was 98.8%. Treatment indication was the only significant factor for 5-year bRFS in multivariate analysis which was 84.6% vs. 67.6% for ART or eSRT vs. SRT respectively (HR 0.15, 95% CI 0.05–0.47, p=0.001). Acute GI toxicity grade 2 was recorded in 24%, grade 3 in 2% and acute GU toxicity grade 2 in 10% and no grade 3. Cumulative rate of late GI toxicity grade ≥2 was observed in 9% and late GU toxicity grade ≥2 in 16%. Conclusion: Observed results confirmed efficacy and acceptable toxicity of post-prostatectomy hypofractionated radiotherapy in 16 daily fractions.

Drosophila melanogaster serves as a important research model both for genetic investigations and for the study of metal toxicity, facilitating the elucidation of physiological mechanisms comparable to those of human organisms. In our research, we evaluated the toxicity effect resulting from exposure to various concentrations of lead and copper on the prolificity rates throughout the life cycle (egg-adult) of four genotypes of Drosophila melanogaster: wild-type (control), white, brown, and white-vestigial. During our study, the prolificity rates were examined across three repetitions under the impact of exposure to concentrations of 0.50, 1.00, 2.00, and 4.00 mM of copper (CuSO₄) and lead (Pb(C₂H₃O₂₎₂). Prolificity rates throughout the life cycle exhibited variations as a direct consequence of genetic factors, the concentration of exposure, and the specific type of metal, either copper or lead. The mutant white-vestigial genotype revealed an IC₅₀ concentration for prolificity inhibition at lower doses of 2.00 mM for copper and 4.00 mM for lead, in contrast to the control genotype (wild-type), which exhibited an inhibition concentration rate >IC₅₀ of 4.00 mM only in the case of copper. Our results concluded that the (i) dose influences the prolificity rate in a directly proportional manner, (ii) comparative analyses between copper and lead revealed that copper displayed toxicity across all genotypes within the concentration range of 0.50 mM to 2.00 mM. In contrast, lead exhibited toxicity within the concentration range of 1.00 mM to 4.00 mM, highlighting a (iii) more acute toxicity characteristic in the case of copper. Thus, the results of this research reflect the importance of using Drosophila melanogaster as a genetic model in the comparative study of the interaction between genetic factors and the toxicity of metals, offering significant insights into monitoring their impact and defining the maximum permissible doses on organisms.

Scientific studies on the impact of wood species on solid fuel production, performance, and sustainability are grossly inadequate. The knowledge of this is imperative as users of solid fuels are increasing rapidly, especially in Africa. On this note, it becomes necessary to explore measures that will improve its efficiency and sustainability as an energy source. This study investigates some properties of selected wood species used as an energy source in Nigeria and their pelleting potential. Nine (9) samples were characterized and assessed for suitability of pelleting following four wood pellet quality standards. The findings revealed Anogeissus leiocarpus as the species with the best rating score in terms of fuel properties while Vitellaria paradoxa as the lowest. However, in terms of conformity with the four wood pellets standards, Khaya senegalensis, Parkia biglobosa and Anogeissus leiocarpus having presented density, calorific value, sulfur, arsenic, cadmium, and lead within the limits of the wood pellet quality standards were considered the best wood species in terms of fuel suitability and pelleting potential. The findings therefore suggest that not all wood species are suitable as fuel. Thus, for species that do not meet the standard wood pellet requirements, alternatives such as the use of biomass blends, additives, or process adjustments can be employed to adapt the quality to the standards or by using the fuels in improved cookstoves.

One of the most concerning global environmental issues is the pollution of agricultural soils by heavy metals (HMs), especially cadmium (Cd), which not only affects human health by taking Cd-containing foods but also impacts the quality of rice. The soil's nitrification and denitrification processes, coupled with the release of volatile organic compounds by plants, raise substantial concerns. The understanding of three aspects of paddy soil under conditions of heavy-metal pollution and water management is currently limited. In this review, we summarized recent literature related to the deleterious effects of Cd on both soil processes related to the N cycle and rice quality, particularly aroma, in different water management practices. Under both continuous flooding (CF) and alternate wetting and drying (AWD) conditions, cadmium (Cd) has been observed to reduce both nitrification and denitrification processes. The adverse effects are more pronounced in continuous flooding (CF) compared to alternate wetting and drying (AWD). Similarly, the alteration in rice aroma is more significant in AWD than in CF. The precise modulation of volatile organic compounds (VOCs) by Cd, remains unclear based on the available literature. Nevertheless, HM accumulation is higher in AWD conditions compared to CF, leading to a detrimental impact on volatile organic compounds (VOCs). The literature concluded that AWD practices should be avoided in Cd contaminated fields to decrease accumulation and maintain the quality of rice. In the future, rhizospheric engineering and plant biotechnology can be used to decrease the transport of HMs from the soil to the plant’s edible parts.

This review deals with the developmental origins of extraocular, jaw and laryngeal muscles, the expression, regulation and functional significance of myosin heavy chains (MyHCs) they express and changes in MyHC expression during phylogeny. Myogenic progenitors from mesoderm in the prechordal plate and branchial arches specify craniofacial muscle allotypes with different repertoires for MyHC expression. To cope with very complex eye movements, extraocular muscles express 11 MyHCs, ranging from the superfast extraocular MyHC to the slowest, non-muscle MyHC IIB. They have distinct global and orbital layers, singly- and multiply-innervated fibres, longitudinal MyHC variations, and palisade endings that mediate axon reflexes. Jaw-closing muscles express the high-force masticatory MyHC, cardiac or limb MyHCs depending on the appropriateness for the acquisition and mastication of their food. Laryngeal muscles express extraocular and limb muscle MyHCs but shift towards slower MyHCs in large animals. During postnatal development, MyHC expression of craniofacial muscles is subject to neural and hormonal modulation. The primary and secondary myotubes of developing EOMs are postulated to induce, via different retrogradely transported neurotrophins, the rich diversity of neural impulse patterns that regulate the specific MyHCs they express. Thyroid hormone shifts 2A MyHC towards 2B in jaw, laryngeal muscles and possibly extraocular muscles.

Hybrid electric vehicles (HEVs) are perceived as a first step towards the future of sustainable transport. Of course, battery electric vehicles (EVs) are currently ideal for what is wanted to stand for transport in the future. The lack of infrastructure for these vehicles makes many potential users choose hybrid vehicles in these conditions. This paper analyzes the influence of the engine and electric motor of hybrid vehicles on their performances. Three engines with slightly different power and close characteristics were considered for configured models. Also, two electric motors with very different power but having a very close maximum continuous torque have been used in models. One is an induction motor, and the other is a permanent magnet synchronous motor. ADVISOR software has been used for vehicles configuration and simulation. Series and parallel hybrid vehicles have been considered. The main dynamic performances and the fuel consumption in two driving cycles were compared for the configured models. Three conventional models with the same engines used in HEVs have also been simulated for reference. The results highlight that in the case of HEVs, the choice of combination engine/electric motor is crucial in obtaining the best report between dynamic performances and low fuel consumption, and implicitly a low negative impact on the environment.

Silicon is an essential trace nutrient for plant growth and is frequently employed to remediate soils contaminated with heavy metals in agriculture. However, silicon’s role and mechanism in reducing heavy metal toxicity have not been well understood, especially for multi-heavy metals. In this study, the effects of silicon-rich materials (silicate, rice husk biochar (RHB), and bentonite) on growth trait, antioxidant response, and heavy metal accumulation and distribution of wheat grown in two soils polluted by multiple heavy metals (Cd, Zn, Pb, and As) were investigated. The results revealed that the addition of silicon-rich materials enhanced plant growth, improved the photosynthetic attributes in leaf tissues, and decreased the contents of Cd, Zn, Pb, and As in wheat shoots and grains. The examination of the subcellular distribution of heavy metals in plants implied that silicon-rich materials transferred heavy metals as intracellular soluble fractions to the cell walls, indicating the reduction of mobility and toxicity of heavy metals in the plants. In addition, the application of the silicon-rich materials reduced oxidative damage in plants by downregulating plant antioxidant response systems and decreasing the production of malondialdehyde (MDA), ascorbic acid (AsA), and glutathione (GSH). Moreover, fractionation analysis of soil heavy metals showed that silicon-rich amendments could convert bioavailable heavy metals into immobilized forms. The results indicated that silicon-rich materials could remediate multi-heavy metal-polluted soils and promote wheat production.

The objective of this study is to investigate the effect of the premixed ethanol ratio based on the same total heating value in-cylinder on the equivalence ratio distributions and the injected fuel droplet behavior in the cylinder of the RCCI engine. The spray simulation was conducted by dividing two-part. First, the spray validation simulations progressed to find the spray-influenced factor of the test injector. Next, the engine simulations were performed with the spray-influenced factor obtained from spray validation simulations to investigate the effect of the premixed ethanol ratio based on the same total heating value in-cylinder on the injected fuel atomization and the equivalence ratio distributions. The introduced total heating value was fixed at 595J based on the lower heating value of diesel 14mg. The heating value of the premixed ethanol ratio varied from 0% to 40% based on the same total heating value in-cylinder in steps of 10%. It was revealed that when the premixed ethanol ratio based on the same total heating value in-cylinder was increased, the spray tip penetration value was reduced from the time after 4deg of diesel injection start because of the short injection duration by the small amount of diesel fuel. The SMD value was also more enormous up to 32.58% with increasing the premixed ethanol ratio because of the low kinetic energy of the injected fuel by the short injection duration and the slow evaporation of the injected fuel by the low cylinder temperature.

Inflammation is a cause of number of disorders. Many anti-inflammatory drugs are available to cure and prevent inflammation and its related disorders. Some of the drugs are from plant and animal origin. Among animals snake venom is also utilized as treatment option of certain disorders. In the current study the venom of N. oxiana from Northern areas of Pakistan is assayed to determine its anti-inflammatory activity. The Naja oxiana is also called central Asian cobra is endemic to Central Asia. Naja oxiana belong to family Elapidae and it is highly venomous snake. The venom has many enzymatic proteins as well as nonenzymatic proteins that is neurotoxins. The venom is lethal having very high mortality rate and the death may occur due to respiratory failure in 45 minutes to 24 hrs depending upon the nature and amount of venom. As the venom is highly toxic so initially after venom milking its protein estimation was done and toxicity profile and LD50 was determined to find out its therapeutic dose at which anti-inflammatory activity was observed. The toxicity and anti-inflammatory activity was determined on mice model. Inflammation was induced by carrageenan induced peritonitis method. The inflammatory markers ROS, TNF-α and IL-β were determined by ELIZA in peritoneal fluid. The LD50 of crude venom, fraction 1 and fraction 2 was found as 34 µg/kg, 7.4 µg/kg and 416 µg/kg respectively. Anti-inflammatory activity crude venom, fraction 1 and fraction 2 was found at dose 19 µg/kg, 1.8 µg/kg and 267 µg/kg respectively. The levels of inflammatory markers reduced after therapeutic dose administration of venom and its fractions that indicates that it can be utilized as anti-inflammatory agent and so can be effective in various disorders.

The new hybrid composite materials for PEM fuel cell were synthesized by UV-polymerization of acrylic monomers (acrylonitrile (AN), acrylic acid (AA), ethylene glycol dimethacrylate (EGDMA)) and sulfo aromatic monomer – sodium styrene sulfonate (SSS), and tetraethoxysilane/3-methacryloxypropyltrimethoxysilane (TEOS/MAPTMS)-based sol-gel system. By means of X-ray spectroscopy fractal structure of the obtained materials was characterized. Proton conductivity and viscoelastic properties of the materials were investigated depending on the content of inorganic component in nanocomposites. On the basis of impedance studies, an equivalent scheme is proposed that successfully describes the proton conductivity in the synthesized composite electrolyte membranes.

Annually, the oak forests of the Zagros Mountain chains, in western Iran and northeastern Iraq, face recurring challenges posed by forest fires, particularly in the Kurdo-Zagrosian forests situated in western Iran and northeastern Iraq. Assessing fire susceptibility relies significantly on vegetation condition. Integrating in situ data, Remote Sensing (RS) data, alongside the integration of Geographical Information Systems (GIS), presents a cost-effective and precise approach to capturing environmental conditions before, during, and after fire events, minimizing the need for extensive fieldwork. This study refines and applies the Zagros Grass Index (ZGI), a local vegetation index tailored to discern between grass-covered surfaces from tree canopies in Zagros forests, identifying the grass masses as the most flammable fuel type. Utilizing Moderate Resolution Imaging Spectroradiometer (MODIS) Normalized Difference Vegetation Index (NDVI) product as input, from 2013 to 2022, the ZGI aims to mitigate the influence of tree canopies, isolating NDVI values solely attributable to grass cover. By incorporating phenological characteristics of forest trees and grass species, the ZGI outperforms NDVI in mapping grass-covered areas that are crucial for fire susceptibility assessment in the study region. Results demonstrate a strong overlap between ZGI-based maps and recorded fire occurrences, validating the efficacy of the index in fire susceptibility estimation.

Various metals and semiconductors containing Printed Circuit Boards (PCBs) are abundant in any electronic device equipped with controlling and computing features. These devices inevitably constitute E-waste after the end of service life. The typical construction of PCBs includes mechanically and chemically resistive materials, which significantly reduce the reaction rate or even avoid accessing chemical reagents (dissolvents) to target metals. Additionally, the presence of relatively reactive polymers and compounds from PCBs requires high energy consumption and reactive supply due to the formation of undesirable and sometimes environmentally hazardous reaction products. Preliminarily milling PCBs into powder is a promising method for increasing the reaction rate and avoiding liquid and gaseous emissions. Unfortunately, current state-of-the-art milling methods also lead to the presence of significantly more reactive polymers still adhered to milled target metal particles. This paper aims to find a novel single and two-stage disintegration-milling approach that can provide the formation of metal-rich particle size fractions. The morphology, particle fraction sizes, bulk density, and metal content in produced particles were measured and compared. Research results show the highest bulk density (up to 6.8 g·cm-3) and total metal content (up to 95.2 wt. %) in finest sieved fractions after the single-step milling of PCBs. Therefore, the concentrations of about half tested metallic elements are higher in the single milled specimen and with lower adhered plastics concentrations, as compared to double milled specimens.

In order to study the movement characteristics of fuel in the fuel tank during aircraft maneuvering, this paper conducts numerical simulations of a typical wing fuel tank using the finite point set method based on certain boundary conditions and excitation. The results show that the finite point set method can capture the complex phenomena of fuel free surface fluctuations, surging, rolling and breaking, as well as the change in center of gravity caused by fuel movement. Under aircraft acceleration and pitch angle excitation, fuel will generate sustained impact pressure on the fuel tank wall. The velocity attenuation of fuel flowing through the baffle communication hole is fast, and the flow resistance and energy dissipation of the communication hole buffer the impact of fuel on the fuel tank wall.

The design and integration of intelligent energy management systems in hybrid Electric Vehicle (EV) charging stations, leveraging Industry 4.0 and renewable energy sources, is crucial for advancing sustainability, efficiency, and technological development. This paper introduces a pioneering hybrid EV charging station that employs hybrid power sources, combining photovoltaic panels, a battery, and a fuel cell, each operating at 240V and 14A. Utilizing wireless power transfer technology, the system comprises five integral blocks: a power source, a boost converter, a High-Frequency (HF) inverter, transfer coils, and EV batteries. The optimization process involves two key stages: i) maximum power point tracking optimization of the boost converter, ensuring maximum power generation by varying the duty cycle between 10% and 90%, and ii) the HF phase employing a class-ϕ2 inverter at 30 MHz, synchronized with the resonant frequency of wireless power transfer coils. Control is executed through a digital signal processor card utilizing zero-voltage switching for efficient operations. This design enhances sustainability in EV charging solutions by optimizing power transfer through the use of hybrid sources.

Levels of trace element pollution in surface soil can be estimated using soil analyses and leaching tests. These methods may reveal different results due to the effect of soil properties, such as grain size and mineral composition, on elemental availability. Therefore, this study advocates an alternative method for monitoring and assessment of trace element pollution in surface soil using terricolous fruticose lichens. Lichens growing at abandoned mine sites and unpolluted areas in southwest Japan and their substrata were analyzed using inductively coupled plasma-mass spectrometry and X-ray fluorescence spectrometry to clarify the relationships between Cu, Zn, As, and Pb concentrations in lichens and soils, including their absorption properties. Concentrations of these elements in the lichens were positively correlated with those in the soils regardless of lichen species, location, habitat, or conditions of soils. The analyzed lichens had neither competitive nor antagonistic properties in their elemental absorption, which made them good biomonitors of trace element pollution in surface soil. The distribution maps of average Cu, Zn, As, and Pb concentrations at each sampling region detected almost all of the Cu, Zn, and As pollution of the soils. Therefore, lichens could be used in practical applications to monitor Cu, Zn, and As pollution in surface soils.

In chemotherapy practice the dexamethasone is used as concomitant agent to mitigate the side effects of antitumor drug cisplatin. However, it is known, that both cisplatin and dexamethasone are capable to stimulate the production of reactive oxygen spacies, which targets various biomolecules, including lipids. This work is devoted to the study of quantitative changes in products of lipid peroxidation in the nuclei of cells of some tissues of rats after separate and combined use of cisplatin and dexamethasone. The amount of lipid peroxidation products was determined by spectrophotometric method after its extraction by heptan-isopropanol mixture. When used separately, cisplatin and dexamethasone enhance the formation of lipid peroxidation products in the studied tissues of rats to various degrees. As a result of these alterations, the values of the oxidation index in the studied nuclear preparations also changed accordingly. During the combined use of cisplatin and dexamethasone there is some antagonism in the action of these drugs. Instead of the supposed summation of the effects of enhancing lipid peroxidation processes, “masking” of the effect of cisplatin with dexamethasone is observed. Thus, it has been assumed that exactly such antagonism revealed during combined action helps mitigate the side effects of cisplatin with dexamethasone.

Total Twenty-Four Samples were collected from the Four different depths of Prayagraj, Uttar Pradesh near the bank of Yamuna River and determined Phosphorous (P) fractions and their relationship with soil properties, The soils were Neutral, low salinity and medium to rich in organic matter in the surface to subsurface horizons. Most of the soils showed Low range in nitrogen and phosphorous and high in potassium. Among the P fractions, the most predominant were Ca-P and followed by Fe-P > S-P > Occl-P > Red-P > Al-P. The Overall results showed that the available-P, organic-P and total-P decreases with increase the depth, Where the Ca-P was significantly positively correlated with pore space (r = 0.396*), Organic Carbon ( r = 0.555*), Available Nitrogen ( r = 0.55*) and significantly negatively correlated with Clay (r = -0.324*), pH ( r = -0.226*), EC ( r = -0.232*). Total-P and Occ-P are main contributing factors for the availability of P. The regression equations showed that soil pH was the main soil property that influences the different fraction of P. The Nutrient Index of available P for Inceptisols was found under medium to low category, about 60% of Inceptisols are likely to respond of P-fertilizer.

Ca-bentonite (CB) alone and in a mixture with limestone (L), tobacco biochar (TB) and zeolite (Z) on the fixation, geochemical fractions and absorption of Cd and Zn by Chinese cabbage in smelter heavily polluted (S-HP) and smelter low polluted (S-LP) soils were investigated. The results showed that the CB+TB and CB+L+TB treatments significantly immobilized Cd up to 22.03% and 29.68%, respectively, and reduced uptake by Chinese cabbage shoot to 35.98% with CB+Z+L and 61.35% with CB+L in S-HP and S-LP soils compared with the control. The CB+ Z+ L+TB treatment mobilized Cd up to 4.45% and increased absorption in the shoot by 9.85% in S-HP soil. The greatest immobilization of Zn was 53.18% and 58.20% with the CB+Z+L+TB treatment, which reduced Zn uptake in the plant shoot by 9.94% with CB + L and 58.04 with CB+Z+L+TB in S-HP and S-LP soils. The CB+Z+TB and CB+TB treatments mobilized Zn up to 35.40% and 4.80%, respectively, in both soils. Furthermore, the uptake of Zn in plant shoot was observed by 58.96% and 7.82% with application of CB+Z and CB+TB treatments, respectively, in S-HP and S-LP soils. Overall, our results suggest that Ca-bentonite alone and in mixtures with different amendments can be used to reduce the phyto-extraction of Cd and Zn in Zn-smelter polluted soils.

The construction of optimized biological fuel cells requires a cathode which combines the longevity of a microbial catalyst with the power density of an enzymatic catalyst. Laccase secreting fungi were grown directly on the cathode of a biological fuel cell to facilitate the exchange of inactive enzymes with active enzymes with the goal of extending the lifetime of laccase cathodes. Additionally, a functionally graded coating was developed to increase enzyme loading at the cathode. Directly incorporating the laccase producing fungus at the cathode extends the operational lifetime of laccase cathodes while eliminating the need for frequent replenishment of the electrolyte. Additionally, the hybrid microbial-enzymatic cathode addresses the issue of enzyme inactivation by using the natural ability of fungi to exchange inactive laccases at the cathode with active laccases. Finally, enzyme adsorption was increased through the use of a functionally graded coating containing an optimized ratio of titanium dioxide nanoparticles and single walled carbon nanotubes. The hybrid microbial-enzymatic fuel cell combines the higher power density of enzymatic fuel cells with the longevity of microbial fuel cells and demonstrates the feasibility of a self-regenerating fuel cell in which inactive laccases are continuously exchanged with active laccases.

The current study evaluated the effect of powder fractions based on particle size on the chemical composition of macronutrients such as proteins and sugars, on phytochemical properties (total content of polyphenolic compounds, vitamin C and antioxidant activity), on preservation capaci-ty (water activity), reconstitutability properties (water absorption capacity and water solubility index) and physicochemical properties (particle size distribution and moisture content) of black-thorn berries (Prunus spinosa) powders. The fruits were separated from the plant material and seeds, dried and then ground using a FRITSCH PULVERISETTE 19 universal mill for hard mate-rials. Eight fractions were obtained after sieving on seven sieves with different mesh sizes, such as: 1 mm, 0.8 mm, 0.630 mm, 0.450 mm, 0.315 mm, 0.200 mm, 0.125 mm. The grinding/sieving pro-cedure was effective in separating Prunus spinosa powder into sufficiently different size classes. The maximal moisture content and water activity were 5.61% and 0.250 respectively, show the good preservation from a microbiological point of view and ensure prevention the oxidation of bi-ologically active compounds of blackthorn berries powders. For samples with reduced particle sizes, reconstitutability was greatly improved. Total phenolic content, protein content, carbohy-drates and antioxidant activity showed significant improvements for some particle size classes compared to the unsieved sample. Vitamin C presented a semnificative content for the fraction with particle large sizes, precisely because they did not undergo intense degradation processes. Therefore, the technique of grinding and successive sieving proved effective in enhancing the physicochemical and functional characteristics of powdered blackthorn berries, particularly for smaller particles.

Aquifer Thermal Energy Storage (ATES) systems are garnering attention as high-efficiency air conditioning technologies that contribute to the realization of a carbon-neutral society. This study focuses on an ATES system constructed in Japan, characterized by its complex geological conditions and thin aquifer layers. Through performance analysis using four years of operational data, we achieved a Coefficient of Performance (COP) of 5 on the building load side. This paper confirms the equivalence of the dimensionless production temperature and heat recovery rate, observing nearly identical changes in the dimensionless production temperature over four cycles (eight seasons). Furthermore, we propose an operational method for the following fiscal year that maintains the balance between accumulated storage quantity and pumping volume, based on predictions from this plant's operational pattern.

Heavy and light quarks produced in high-pT partonic collisions radiate differently. Heavy quarks regenerate their color field, stripped-off in the hard reaction, much faster than the light ones and radiate a significantly smaller fraction of the initial quark energy. This peculiar feature of heavy-quark jets leads to a specific shape of the fragmentation functions observed in e+e− annihilation. Differently from light flavors, the heavy quark fragmentation function strongly peaks at large fractional momentum z, i.e. the produced heavy-light mesons, B or D, carry the main fraction of the jet momentum. This is a clear evidence of the dead-cone effect, and of a short production time of a heavy-light mesons. Contrary to propagation of a small qq¯ dipole, which survives in the medium due to color transparency, a heavy-light Qq¯ dipole promptly expands to a large size. Such a big dipole has no chance to remain intact in a dense medium produced in relativistic heavy ion collisions. On the other hand, a breakup of such a dipole does not affect much the production rate of Qq¯ mesons, differently from the case of light qq¯ meson production.

Composite membranes formed by sulfonated poly(ether ether ketone) (SPEEK) with embedded carbon quantum dots (CQDs) were used for detection and removal of heavy metal ions, such as lead and cadmium, from water. SPEEK is responsible for the capture of heavy metals based on the cation exchange mechanism, while CQDs detect their contamination by exhibiting changes in fluorescence. Water-insoluble “red” carbon quantum dots (rCQDs) were synthesized from p-phenylenediamine so that their photoluminescence was shifted from that of the polymer matrix. CQDs and the composites were characterized by several techniques: FTIR, Raman, UV/VIS, photoluminescence, XPS spectroscopies and AFM microscopy. The heavy metal ion concentration was analyzed by inductively coupled plasma–optical emission spectroscopy (ICP-OES). The concentration ranges were 10.8 - 0.1 mM for Pb2+ and 10.0 - 0.27 mM for Cd2+. The composite achieved 100% removal efficiency for lead and cadmium if the concentration was below a half of the ion exchange capacity of SPEEK. The regeneration of membranes in 1 M NaCl was also studied. SPEEK/rCQDs showed a turn-off effect more pronounced for lead. A second order law was effective to describe the kinetics of the process.

This study introduces numerical advancements in an alternative design for the SPS Beam Dump Facility (BDF) at CERN. The design envisions a high-power operation target made of flowing liquid lead. The BDF is a proposed versatile facility at CERN, intended for both beam-dump-like and fixed-target experiments. The target behavior is assessed, assuming a proton beam with a momentum of 400 GeV/c, a pulse frequency of 1/7.2 Hz, and an average beam power of 355 kW. An evaluation is conducted using various Computational Fluid Dynamics (CFD) codes to analyze the behavior of liquid lead and to predict the thermal stress on the target vessel induced by the pulsed heat source generated by the charged particle beam. The comparison increases the reliability of the results, investigating the dependencies on the CFD modeling approach. The beam is modeled as a volumetric heat source with data coming from beam-lead interaction simulations provided by CERN and obtained with the Monte-Carlo code FLUKA. The velocity field and stress profiles are utilized to enhance the design of the lead loop and verify its viability and safety when operated with a liquid metal target.

This paper examines the importance of choice of cooking fuels in wellbeing, analysing relationships between the proportion of population with primary reliance on different types of fuels for cooking (predictor variable), and key wellbeing indices (outcome variables) - Personal Health, Social Life, Civic Engagement, Life Evaluation, Negative Experience. By combining two global datasets from Gallup and WHO, the study adds to current evidence by taking a global perspective. Controlling for demographic factors such as income per capita, age, education level, employment, etc., regression modelling of these relationships show that clean cooking fuels are influential in all of the key wellbeing indices with the exception of the Life Evaluation Index. Among the key wellbeing indices, Personal Health and Negative Experience Indices are the most strongly influenced by choice of clean cooking fuels. By adding access to electricity as an additional predictor variable, the analysis highlights the potential for integrating eCooking into national electrification plans as part of sustainable energy transitions, given that health outcomes (Personal health and Negative experience indices) appear to be as closely linked to choice of cooking fuels as to access to electricity.

Microbial Fuel Cells (MFCs) representing a promising technology for the extract of energy and resources through wastewater and it also offer an economic solution to the problem of environment effluent and energy crisis in near future. The advance device is rather appealing, due its potential benefits, its practical application is, however hindered by several drawbacks, such an internally competing microbial reaction, and low power generation. This report is an endeavor to address various design connected to the MFCs application to wastewater treatment, in particular cost effective bioelectricity from waste water are reviewed and discussed with a multidisciplinary approach. The conclusions drawn herein can be of practical interest to all new researchers dealing with effluent wastewater treatment using MFCs.

The influence of long-term chemical fertilization in paddy soils is based on the interaction between labile carbon and phosphorus fractions and how this influences soil organic carbon (SOC). Four soil depths (0–30 cm) were analyzed in this study. Easily oxidized organic carbon components, such as permanganate oxidized carbon (POXC) and dissolved organic carbon (DOC), and other physicochemical soil factors were evaluated. The correlation and principal component analyses were used to examine the relationship between soil depth and the parameter dataset. The results showed that Fe-P concentrations were greater in the 0–5 cm soil layer. DOC, inorganic phosphate fraction, and other soil physiochemical characteristics interacted more strongly with SOC in the 0–5 cm soil layer, compared to that in the 10–15 cm layer, influencing soil acidity. An increase in DOC in the 0–5 cm soil layer had a considerable effect on lowering SOC, consistent with P positively correlated with POXC, but negatively with SOC and water-soluble carbon (WSC). The changes in SOC could be attributed to the relationship between DOC and inorganic phosphate fractions (as Fe-P) under a specific soil pH condition. An increase in soil DOC could be caused by changes in the P fraction and pH. The DOC:Avai. P ratio could serve as a compromise for the C and P dynamic indicators. The soil depth interval is a critical element that influences these interactions. Agricultural policy and decision-making may be influenced by the P from chemical fertilization practices, considering the yields and environmental effects.

Sumudu transform of the Dixon elliptic function with non zero modulus a ≠ 0 for arbitrary powers sm^N(x,a) ; N ≥ 1 ; sm^N(x,a)cm(x,a) ; N ≥ 0 and sm^N(x,a)cm²(x,a) ; N ≥ 0 is given by product of Quasi C fractions. Next by assuming denominators of Quasi C fraction to 1 and hence applying Heliermann correspondance relating formal power series (Maclaurin series of Dixon elliptic functions) and regular C fraction, Hankel determinants are calculated and showed by taking a = 0 gives the Hankel determinants of regular C fraction. The derived results were back tracked to the Laplace transform of sm(x,a) ; cm(x,a) and sm(x,a)cm(x,a).

Nuclear waste is one of the most important environmental problems of nuclear power plants. A novel renewable distillation method has been proposed for an on-site recycling of the spent nuclear fuel and separation of its valuable components from the fissile isotopes, which is especially applicable for reactors using liquid fuels.

The rapid technological development of society determined increased demand for safe potable water and food resources. Unfortunately, this progress causes complex environmental pollution, that is continuously challenging the scholars’ community. Therefore, it is important to chemically analyze the food for a better understanding of pollution-spreading mechanisms. Our study is focused on food analysis originating from Vatra Dornei City, which belongs to Suceava County in the Bukovina region of Romania. It represents a well-known Romanian spa and ski resort in the northern parts of the Oriental Carpathians Mountains. The mountain region owns a lot of mineral resources, mainly consisting of mineral and sparkling waters, uranium, manganese, copper, pyrite, chalcopyrite, polymetallic ores, baryte, gold and silver-bearing orebodies, etc. The present contribution aims to point out the results obtained from the analysis of soil, water and food samples collected from the local markets. The food samples consisted of lettuce, spinach, apples, pork (smoked) chicken meat (raw), milk and cheese. Last year the survey was conducted over six months. The results highlighted that the mining activities carried out during time caused environmental pollution with uranium and heavy metals due to the waste heaps’ weathering phenomena and tailing ponds’ presence.

We describe a vision for a national-scale heavy mineral (HM) map generated through automated mineralogical identification and quantification of HMs contained in floodplain sediments from large catchments covering most of Australia. The composition of the sediments reflects the dominant rock types in each catchment, with the generally resistant HMs largely preserving the mineralogical fingerprint of their host protoliths through the weathering-transport-deposition cycle. Heavy mineral presence/absence, absolute and relative abundance, and co-occurrence are metrics useful to map, discover and interpret catchment lithotype(s), geodynamic setting, magmatism, metamorphic grade, alteration or mineralization. Underpinning this vision is a pilot project, focusing on a subset of the national sediment sample archive, which is used to demonstrate the feasibility of the larger, national-scale project. We preview a bespoke, cloud-based mineral network analysis (MNA) tool to visualize, explore and discover relationships between HMs as well as between them and geological setting or mineral deposits. We envisage that the Heavy Mineral Map of Australia and MNA tool will contribute significantly to mineral prospectivity analysis and modeling here, particularly for technology critical elements and their host minerals, which are central to the global economy transitioning to a more sustainable, decarbonized paradigm.

This paper presents a review of the electrical heating method for heavy oil recovery based on past, current, and future prospects of electrical heating. Heavy oil is one of the potential crude oil used as a link to reduce the crisis of light oil used today. The obstacle of heavy oil is a high viscosity and density in which thermal injection is a method for heavy oil recovery, but it results in economic and environmental issues. Electrical heating is one of the thermal methods by transferring heat into the reservoir. The basic process of electrical heating is to increase the mobility of the oil. Because the temperature rises, it can reduce oil viscosity and makes it easier for heavy oil to flow. The past and current developments have been carried out to fill up the gap of electrical heating projects. The future prospects must meet energy efficiency, and the excessive heat will damage formation that must be tackled in the future prospect. the works adopt several electrical heating projects and applications in the world where the works give a brief future prospect of electrical heating.

The sPHENIX experiment is a state-of-the-art jet and heavy flavor physics detector which successfully recorded its first Au + Au collision data at 200 GeV at RHIC. sPHENIX will provide heavy flavor physics measurements covering an unexplored kinematic region and unprecedented precision at RHIC to probe the parton energy loss mechanism, parton transport coefficients in quark-gluon plasma, and the hadronization process under various medium conditions. At the center of sPHENIX, the Monolithic-Active-Pixel-Sensor (MAPS) based VerTeX detector (MVTX) is a high-precision silicon pixel detector. The MVTX provides excellent position resolution and the capability of operating in continuous streaming readout mode, allowing precise vertex determination and recording a large data sample, both of which are particularly crucial for heavy flavor physics measurements. In this work, we will show the general performance of heavy-flavor hadron reconstruction. In addition, we will discuss the commissioning experience with sPHENIX. Finally, we will provide the projection of b-hadron and jet observables and discuss the estimated constraints on theoretical models.

Heavy metal pollution poses a significant threat to global populations, particularly impacting human health. Developing countries, characterized by chemical engineering and mining industrial activities, often contribute to diverse heavy metal contaminants. Consumption of water contaminated with heavy metals, prevalent in such regions, can lead to severe health risks, including gastric cancer. Addressing the urgent issue of heavy metal pollution, this paper employs a bibliographic approach to explore the latest literature on heavy metal pollution. The study discusses recent research findings and potential methods for the treatment and mitigation of heavy metal pollution, emphasizing the pressing need for effective solutions to safeguard public health.

Guava (Psidium guajava L.) is a common fruit tree that grows in several tropical and subtropical parts of the world. The aim of this study was to employ the use of liquid-liquid fractionation to investigative the comparative antibacterial potential of crude extracts of Guava leaves and bark against selected food isolates; Escherichia coli, Pseudomonas aeruginosa, Streptococcus pneumonia, Bacillus cereus and Staphylococcus aureus. The phytochemical analysis of the extract showed presence of tannin, phenol, flavonoid and terpenoid in all extract, while steroid and saponin were absent in some. The agar diffusion method was employed for the assessment of the sensitivity of the extracts. The ethyl acetate and aqueous fractions from the stem bark acetone extract generally showed better antimicrobial activity compared with other extracts from leaves. The extract was active both against gram positive bacteria (Bacillus cereus and Streptococcus pneumonia) and gram negative bacteria (Escherichia coli, Pseudomonas aeruginosa, , Bacillus cereus and Staphylococcus aureus) at varying zone of inhibition. The results of the study showed the potential of identifying novel antibacterial agent from P. guajava bark and leaves while optimising the potential application for treatment in traditional medicine.

Exsolved perovskites can be obtained from lanthanum ferrites, such as La0.6Sr0.4Fe0.8Co0.2O3, as result of Ni doping and thermal treatments. Ni can be simply added to the perovskite by an incipient wetness method. Thermal treatments include calcination in air (e.g., 500 °C) and subsequent reduction in diluted H2 at 800 °C to favor the exsolution process. The chemistry of the nanoparticles exsoluted on the substrate surface can be further modulated by a post treatment in air. These processes allow to produce a two-phase material consisting of a Ruddlesden-Popper type structure and a solid oxide solution e.g. α-Fe100-y-zCoyNizOx oxide. The formed electro-catalyst shows sufficient electronic conductivity under reducing environment at the SOFC anode. Outstanding catalytic properties are observed for the direct oxidation of dry fuels in SOFCs, including H2, methane, syngas, methanol, glycerol and propane. This anode electrocatalyst can be combined with full density electrolyte based on Gadolinia-doped Ceria or with La0.8Sr0.2Ga0.8Mg0.2O3 (LSGM) or BaCe0.9Y0.1O3-δ (BYCO) to form a complete perovskite structure-based cell. Moreover, the exsolved perovskite can be used as a coating layer or catalytic pre-layer of a conventional Ni-YSZ anode. Beside the excellent catalytic activity, this material also shows proper durability and tolerance to sulphur poisoning. In this mini review, preparation methods, physico-chemical characteristics, surface properties of exsoluted and core-shell nanoparticles encapsulated on the metal-depleted perovskite substrate surface, electrochemical properties for the direct oxidation of dry fuels and related electrooxidation mechanisms are examined and discussed.

Heat and power cogeneration plants based on fuel cells are interesting systems for energy- conversion at low environmental impact. Different fuel cells have been proposed, but experimental testing rigs are expensive and the development of commercial systems is time consuming if based on fully experimental activities. Furthermore, tight control of operation of fuel cells is compulsory to avoid damage, which must be based on accurate models, able to predict the cell behaviour and prevent stresses and shut-down. Some selected examples of steady state, dynamic and fluid dynamic modelling of different types of fuel cells are proposed, mainly PEMFC and SOFC type. The general ideas behind the thermodynamic, kinetic and transport description are recalled, with some examples of models derived for single cells, stacks and integrated power co-generation units.

River sediment from two inflow watersheds (Hongze and Tiaoxi) to Hongze and Taihu Lake in Eastern China was analyzed by the sequential extraction procedure. This study aimed to explore a spatial distribution of phosphorus fractions in river sediments and analysed the relationship between different phosphorus fractions and their environmental influence on the sediments within different watersheds in Eastern China. Five fractions of sedimentary phosphorus, including freely sorbed phosphorus, were all analyzed (NH₄Cl-P), redox-sensitive phosphorus (BD-P), bound phosphorus metal oxide (NaOH-P), bound phosphorus calcium (HCl-P) and residual phosphorus (Res-P). The order of rank of the P fractions for the river Anhe was HCl-P>NaOH-P>BD-P>NH₄Cl-P; whereas that of the Suihe river was HCl-P>BD-P>NaOH-P>NH₄Cl-P. For the rank order of the Hongze watershed, HCl-P was higher while the NH₄Cl-P contents were significantly lower. The rank order for the Dongtiaoxi river was NaOH-P > HCl-P> BD-P> NH₄Cl-P and that of Xitiaoxi river was NaOH-P> BD-P> HCl-P> NH₄Cl-P. Compared with phosphorus forms of Tiaoxi watershed, NaOH-P contents were significantly higher in the converse of HCl-P contents were significantly higher in Hongze watershed while both in NH₄Cl-P contents were significantly lower. Variations may be attributed to differential discharge of P watershed form due to land-use changes and urban river ambient conditions.

Electrochemical energy conversion and storage is key for the use of regenerative energies at large scale. A thorough understanding of the individual components, such as the ion conducting membrane and the electrode layers, can be obtained with scattering techniques on atomit to molecular length scales. The largely heterogeneous electrode layers of High-Temperature Polymer Electrolyte Fuel Cells are studied in this work with small- and wide-angle neutron scattering at the same time with the iMATERIA diffractometer at the spallation neutron source at J-PARC, opening a view on structural properties on atomic to mesoscopic length scales.

Normally, the Nernst voltage calculated from the concentration of the reaction gas in the flow channel is considered to be the ideal voltage (reversible voltage) of the oxyhydrogen fuel cell, but actually it will cause a concentration gradient when the reaction gas flows from the flow channel through the gas diffusion layer to the catalyst layer. The Nernst voltage loss in fuel cells in most of the current literature is thought to be due to the difference in concentration of reaction gas in the flow channel and concentration of reaction gas on the catalyst layer at the time when the high net current density is generated. Based on the Butler-Volmer equation in oxyhydrogen fuel cell, this paper demonstrates that the Nernst voltage loss is caused by the concentration difference of reaction gas in flow channel and on the catalytic layer at the time when equilibrium potential (Galvanic potential) of each electrode is generated.

Fuel gas network (FGN) synthesis is a systematic method for reducing fresh fuel consumption in a chemical plant. In this work, we address the synthesis of fuel gas network using block superstructure originally proposed for process design and intensification (Demirel et.al. [1]). Instead of a classical source-pool-sink superstructure, we consider a superstructure with multiple feed and product streams. These blocks interact with each other through direct flows that connect a block with its adjacent blocks and through jump flows that connect a block with all blocks. The blocks with feed streams are viewed as fuel sources and the blocks with product streams are regarded as fuel sinks. Addition blocks can be added as pools when there exists intermediate operations among 9 source blocks and sink blocks. These blocks can be arranged in a I × J two-dimensional grid with I = 1 for problems without pools, or I = 2 for problems with pools. J is determined by the maximum number of pools/sinks. With this representation, we formulate fuel gas network synthesis problem as a mixed-integer nonlinear (MINLP) problem to optimally design a fuel gas network with minimal total annul cost. We present a real-life case study from LNG plant to demonstrate the capability of the proposed approach.

Gasca D herbal formulation is an antidiabetic medicine for the management of diabetes mellitus produced exclusively from natural ingredients. The level of some essential elements (Copper, chromium, Cobalt, Iron, Manganese, Nickel and zinc) and toxic (Cadmium, Arsenic, Mercury, and Lead) heavy metals were determined using microwave plasma-atomic emission spectrometry (MP-AES). The aim of this study is to evaluate the levels of essential and toxic heavy metals and also identify bioactive compounds present in Gasca D herbal formulation. The result shows no traces of Lead, Mercury, Zinc, Arsenic and Zinc, Iron was found to have highest concentration 67.16 + 7.5 µg/g and Cadmium lowest concentration 0.4 + 0.03µg/g. GC-MS analysis of Gasca D herbal formulation revealed the presence of 14 biologically active compounds which include N-Formyl-beta-alanine, Paromomycin, 3,4-Altrosan, Benzamide, 1,3,4-Thiadiazol-2-amine, Carbamodithioic acid, Carbonic acid, alpha-D-Glucopyranoside, Ethyl isocyanide, 2-Propanesulfinic acid, Propanamide, 2-Butenenitrile, Dicyclopropyl carbinol, Isoxazolidine, 1,5-Hexadiene 10-Azido-1-decanethiol. Conclusion: The result indicates that the mean levels of toxic metals in Gasca D herbal formulation were below WHO permissible levels. Gasca D herbal formulation also contains various bioactive compounds that can have various medicinal application which can be used for the treatment of various diseases.

This work shows the physicochemical and mineralogical characterization of diatomites form the Hidalgo and Jalisco States, Mexico. In the case of the mineral from Hidalgo State, this has the following chemical composition; 70.0 % wt. SiO₂, 11.63 wt. % Al₂O₃, 1.95 wt. % FeO, 1.79 wt. % MgO, 2.41 wt. % K₂O, 0.85 wt. % CaO and 6.10 wt. % Na₂O. On the other hand, the mineral from Jalisco has the following chemical composition; 93.58 wt. % SiO₂, 3.03 wt. % Al₂O₃, 1.81 wt. % FeO, 0.40 wt. % MgO, 0.92 wt. % K₂O, 0.11 wt. % CaO and 0.24 wt. % Na₂O. For recovery of metals, both minerals got arsenic, silver, lead and nickel recoveries upper to 95 % and lower to 10 % for chromium. According to efficiency of interchange, the mineral from Hidalgo is slightly higher in the case of arsenic, lead and silver; while for nickel and particularly chromium (VI) the efficiency is higher for the mineral from Jalisco.

Microgrids offer flexibility in power generation in a way of using multiple renewable energy sources. In the past few years, microgrids become a very active research area in terms of design and control strategies. Most of the microgrids use DC/DC converters to connect renewable energy sources to the load. In this paper, the simulation model of a DC microgrid with three different energy sources (Lithium-ion battery (LIB), photovoltaic (PV) array, and fuel cell) and external variant power load is built with MATLAB/Simulink and the simulative results show that the stability of DC microgrid can be guaranteed by the proposed maximum power point controller MPPT. The three energy sources are connected to the load through DC/DC converters, one for each. This type of topology ensures protection for each energy source as well as optimum stability at the load.

In this study, the physical properties of briquettes produced from two different biomass feedstocks (sawdust and date palm trunk) and different plastic wastes were investigated, without using any external binding agent. The biomass feedstocks were blended with different ratios of two WEEE plastics (halogen-free wire and print circuit boards (PCB)) and automotive shredder residues (ASR). The briquettes production is studied at different waste proportions (10-30%), pressures (22-67 MPa) and temperatures (room-130 ˚C). Physical properties as density and durability rating were measured, usually increasing with temperature. Palm trunk gave better results than sawdust in most cases, due to its moisture content and the extremely fine particles that are easily obtained.

Currently, most plastic waste stems from packaging materials, with a large proportion of this waste either discarded or used to derive fuel. Accordingly, there is growing interest in the use of pyrolysis in the context of chemically recycling non-recyclable (i.e., via mechanical means) plastic waste into petrochemical feedstock. The aim of this study is to use kinetic analyses to elucidate the pyrolytic properties of solid recovered fuel (SRF) produced using two types of reactors, namely, fixed bed and fluidized bed reactors. From the kinetic analysis, the activation energy corresponding to the rate of pyrolysis reaction conversion was obtained. In conclusion, we found that the pyrolysis occurs more vigorously in fluidized bed reactors compared to fixed bed reactors.

In the development of the safety-critical systems, it is important to perform Failure Modes and Effects Analysis (FMEA) process to identify potential failures. However, traditional FMEA activities tend to be considered difficult and time-consuming tasks. To compensate for the difficulty of the FMEA task, various types of tools are used to increase the quality and the effectiveness of the FMEA reports. This paper explains an Automatic FMEA tool which integrates the Model-based Design (MBD), FMEA, and Simulated Fault Injection techniques in a single environment. The Automatic FMEA tool has the following advantages compared to the existing FMEA analysis tool. First, the Automatic FMEA tool automatically generates FMEA reports compared to the traditional spreadsheet-based FMEA tools. Second, the Automatic FMEA tool analyzes the causality between the failure modes and the failure effects by performing model-based fault injection simulation. In order to demonstrate the applicability of the Automatic FMEA, we used the electronic fuel injection system (EFI) Simulink model. The results of the Automatic FMEA were compared to that of the legacy FMEA.

Ethanol produced from various biobased sources (bioethanol) has been gaining high attention lately due to its potential to cut down net emissions of carbon dioxide while reducing burgeoning world dependence on fossil fuels. Global ethanol production has increased more than six-fold from 18 billion liters at the turn of the century to 110 billion liters in 2019 (1,2). Sugar cane and corn have been used as the major feedstocks for ethanol production. Lignocellulosic biomass has recently been considered as another potential feedstock. This paper reviews recent developments and current status of commercial production of ethanol across the world. The review includes the ethanol production processes used for each type of feedstock, both currently practiced at commercial scale and newly developed technologies, and production trends in various regions and countries in the world.

The objective of this work is to compare how the gases emitted during the manufacture of the clinker vary in a cement plant, using two types of fuel: petroleum coke and unusable tires (UTs). The study is based on a case study using real time data on more than 40 process variables. Gases are analysed from two points of the production process: Sintering Kiln, main focus of emission to the atmosphere by chimney, and Preheater. The variation of CO and NOx depending on the oxygen and fuel type is studied. The SO2 levels are also analyzed, observing a decrease when using the UTs. The quality of the Clinker has been compared depending on the fuel type. The results are compared, on the one hand, with the quality of the clinker, determined by the content of the majority (C3S, Alite) and minority (Free CaO) phases, and, on the other hand, with the Kiln sintering temperature, the most influential parameter in the productive process. It is verified that Clinker quality is maintained, regardless of the type of fuel used. Concluding that the use of UTs as fuel can generate an important economic and environmental benefit for cement companies and their environment.

This paper investigates the randomly stopped sums, minima and maxima of heavy- and light-tailed random variables. The conditions on the primary random variables, which are independent but generally not identically distributed, and counting random variable are given in order that the randomly stopped sum, random minimum and maximum is heavy/light tailed. The results generalize some existing ones in the literature. The examples illustrating the results are provided.

Huntington’s disease (HD) is a rare but progressive and devastating neurodegenerative disease characterized by involuntary movements, cognitive decline, executive dysfunction, and neuropsychiatric conditions such as anxiety and depression. It follows an autosomal dominant inheritance pattern. Thus, a child who has a parent with the mutated huntingtin (mHTT) gene has a 50% chance of developing the disease. Since HTT protein is involved in many critical cellular processes including neurogenesis, brain development, energy metabolism, transcriptional regulation, synaptic activity, vesicle trafficking, cell signaling, and autophagy, its aberrant aggregates lead to disruption of numerous cellular pathways and neurodegeneration. Essential heavy metals are vital at low concentrations, however, at higher concentrations, can exacerbate HD by disrupting the glial-neuronal communication, and/or causing dysbiosis (disturbance in the gut microbiota, GM), both of which can lead to neuroinflammation and further neurodegeneration. Here, we discuss in detail the interactions of iron, manganese and copper with glial-neuron communication and GM and indicate how this knowledge may pave the way for development of a new generation of disease-modifying therapies in HD.

Intense rainfall events frequently occur in Brazil, often leading to rapid flooding. Despite their recurrence, there is a notable lack of sub-daily studies in the country. This research aims to assess patterns related to the structure and microphysics of clouds driving intense rainfall in Brazil, resulting in high accumulations within 1 hour. Employing a 40 mm/h threshold and validation criteria, 83 events were selected for study, observed by both single and dual-polarization radars. Contoured Frequency by Altitude Diagrams (CFADs) of reflectivity, Vertical Integrated Liquid (VIL), and Vertical Integrated Ice (VII) are employed to scrutinize the vertical cloud characteristics in each region. To address limitations arising from the absence of polarimetric coverage in some events, three case studies focusing on polarimetric variables are included. A fourth case study enhances the overall understanding of these events, emphasizing the underexplored nature of short-term intense rainfall studies in Brazil. Results reveal that the generating system significantly influences the rainfall pattern, especially in the Southern, Southeastern, and Central-Western regions. Regional CFADs unveil primary convective columns with 40-50 dBZ reflectivity, extending to approximately 6 km. The microphysical analysis highlights the rapid structural intensification, challenging the event predictability and the issuance of timely specific warnings.

This study conducts a comprehensive analysis of the presence of heavy metals, including zinc (Zn), lead (Pb), copper (Cu), chromium (Cr), and arsenic (As), in the dust found inside educational buildings and the top layer of soil in different areas of Vilnius. The study focuses on the analysis of topsoil samples gathered between 2011 and 2023, with a specific emphasis on dust samples obtained from 24 schools in 2022. The research reveals significant variations in the concentrations of heavy metals, providing a clear understanding of the complex relationship between sources of urban pollution, environmental processes, and the correlation between soil and dust contamination by heavy metals. Indoor dust in schools shows unique contamination patterns in contrast to topsoil, suggesting distinctive sources of indoor pollution, while there are some general similarities. This finding emphasizes similarities and distinctions between soil and dust in educational environments. The study utilizes advanced statistical methods such as Pearson correlation, Principal Component Analysis (PCA), and hierarchical clustering to examine the distribution and characteristics of these metals. This study distinguishes itself by examining indoor dust in educational facilities and topsoil in Vilnius, providing crucial insights into the relationship between these two environmental matrices.

Over the centuries, honey is known for its superior usage in culinary, and for its rich nutrition and therapeutic values which are scientifically proven in the medical field. The chemical composition of honey varies depending on its botanical sources and environment. Therefore, the nutrition content in honey is highly likely to be affected by contaminants, such as heavy metals and pesticides. To ensure the quality of honey, parameters such as the heavy metal content should be within the safe range of total standard mineral and trace elements as defined by the International Food Standard (Codex Alimentarius), and pesticides should not be present at all. The high concentration of heavy metal and pesticides not only deteriorates the quality and quantity of honey, but also causes harm to the bee colony itself. In the agriculture sector, the excessive usage of pesticides and fertilizer negatively impacts the overall honey production process. Bees, a pollinating agent, bring the polluted nectar back to their beehives, eventually contaminating the honey and depreciating its value. Hence, this article will comprehensively review the activities that contribute to heavy metal and pesticide contamination, the interactions of bees as a pollinating agent, the impact of the pollutant to the colonies, and subsequently to the honey production.

The goal of clustering is to identify common structures in a data set by forming groups of homogeneous objects. The observed characteristics of many economic time series motivated the development of classes of distributions that can accommodate properties such as heavy tails and skewness. Thanks to its flexibility, the Skewed Exponential Power Distribution (also called Skewed Generalized Error Distribution) ensures a unified and general framework for clustering possibly skewed and heavy tailed time series. This paper develops a clustering procedure of model-based type, assuming that the time series are generated by the same underlying probability distribution but with different parameters. Moreover, we propose to optimally combine the estimated parameters to form the clusters with an entropy weighing $k$-means approach. The usefulness of the proposal is showed by means of application to financial time series, demonstrating also how the obtained clusters can be used to form portfolio of stocks.

The copper deposition on the platinum and palladium nanoelectrode has been studied using cyclic voltammetry. The use of nanoelectrode platinum and palladium are defined in the study of heavy metals. The noble nanoelectrode of metal has a typical silicone processing structure. In comparison to the nanoelectrodes, the geometry of the electrode series is complex and balanced. Nanoelectrodes of platinum are found effective in detecting heavy metal. There was regular analysis of the use of the sensors. The identification constraints down to the ng /L level was accomplished by refined electrode geometry and the stripping procedures. The process was used for the study of water sample determination. Another heavy metal ion attack voltammetric reaction was studied. The SEM picture clearly observed and characterized the nanoparticle electrode by X-ray diffraction and cyclic voltammetry.

This study investigates the concentrations of physicochemical and heavy metal contaminants in the groundwater of the Middle Awash Basin, Ethiopia, to inform targeted water management strategies. A total of 32 groundwater samples were collected from 16 stations via piezometers and boreholes at the end of both the dry (June 2021) and wet (October 2021) seasons. Utilizing Inductively Coupled Plasma Mass Spectrometry (ICP-MS), Atomic Absorption Spectroscopy (AAS), and in situ metering, 22 physicochemical and 24 heavy metal parameters were analyzed. The data revealed significant levels of contamination; notably, sample GW11 had extraordinarily high concentrations of total dissolved solids (10,826 mg/L), strontium (908 µg/L), molybdenum (802.4 µg/L), zinc (6060 µg/L), and electrical conductivity (15,645 µS/cm), while GW12 exhibited elevated levels of aluminum (2615 µg/L), zinc (4446 µg/L), and arsenic (117.2 µg/L). Contaminants such as arsenic, vanadium, gallium, lithium, rubidium, chromium, manganese, copper, and zinc were found enriched in groundwater near Lake Beseka, influenced by agricultural runoff from sugarcane plantations and agro-industry activities. Over half of the groundwater sources were unsuitable for drinking, posing significant health risks to local communities that rely heavily on these sources due to limited access to clean surface water. The findings emphasize the urgent need for comprehensive groundwater management and remediation plans in the Middle Awash region to ensure safe and sustainable water use, particularly addressing the variation in contamination levels influenced by Lake Beseka. These measures are critical to protect public health and support local development in the face of ongoing environmental and anthropogenic pressures.

The purpose of this study is to identify the steps involved in fabricating silica/chitosan composite membranes and their suitability in fuel cell application. It also intends to identify the physical characteristics of chitosan composite membranes, including their degree of water absorption, proton conductivity, methanol permeability, and functional groups. In this investigation, composite membranes were fabricated using the solution casting method with chitosan content of 5 g and silica variations dosage of 2% and 4% while stirring at a constant speed for 2h. According to the findings, the analysis of composite membranes produced chitosan membranes that were successfully modified with silica. The optimum membrane was found to be 4% s-SiO2 from the Sol-gel method with composite membrane's optimal condition of 0.234 cm/s proton conductivity, water uptake of 56.21%, and reduced methanol permeability of 0.99 × 10 -7 cm2/s in the first 30 minutes and 3.31 × 10-7 in the last 150 minutes. Maintaining lower water uptake capacity at higher silica content is still a challenge that needs to be addressed. However, the fabricated membranes showed exceptional results in terms of proton conductivity and methanol permeability.

A critical review of recent work on fuel lubricant interactions is undertaken. The work focusses on liquid fuels used in diesel and gasoline vehicles. The amount of fuel that contaminates the lubricant depends on driving conditions, engine design, fuel type and lubricant type. When fuel contaminates a lubricant, the viscosity of the lubricant will change (it will usually decrease), the sump oil level may increase, there may be a tendency for more sludge formation, there may be an impact on friction and wear, and low speed pre-ignition could occur. The increased use of biofuels (particularly biodiesel) may require a reduction in oil drain intervals, and fuel borne additives could contaminate the lubricant. The move to active regeneration of particulate filters by delayed fuel post-injection and the move to hybrid electric vehicles, and vehicles equipped with stop-start systems will lead to increased fuel dilution. This will be of more concern in diesel engines, since significant fuel dilution could still persist at sump oil temperatures in the range 100-150C (whereas in gasoline engines the more volatile gasoline fuel will have substantially evaporated at these temperatures). It is anticipated that more research into fuel lubricant interactions, particularly for diesel engines, will be needed in the near future.

Since World War I, the commercial aviation industry has seen many improvements that now allow people and goods to reach the other side of the world in few hours, consuming much less fuel than in recent decades. Improvements in cargo capacity and energy efficiency were significant and, in this scenario, commercial airlines were able to thrive and bring great benefits to world economy. However, this sector is facing environmental challenges due to the intensive use of aviation fuel. Brazil is one of the largest domestic air passenger markets in the world and still has great growth potential, considering its economic potential and territorial dimensions: roughly the same size as the US and twice the size of the European Union. This paper discusses partial productivity of jet fuel in Brazilian domestic aviation and proposes an econometric method to support public regulators and airlines decisions. The proposed model uses variables such as aircraft size, route characteristics and idle flight capacity in a panel data analysis. The results show that reducing idle capacity is one of the best ways to achieve better short-term fuel efficiency and therefore will reduce environmental impacts and have positive economic effects on commercial air transport activities.

Corn fiber is a co-product of commercial ethanol dry-grind plants, which is processed into distillers dried grains with solubles (DDGS) and used as animal feed, yet it holds high potential to be used as feedstock for additional ethanol production. Due to the tight structural make-up of corn fiber, a pretreatment step is necessary to make the cellulose and hemicellulose polymers in the solid fibrous matrix more accessible to the hydrolytic enzymes. A pretreatment process was developed in which whole corn kernels were soaked in aqueous solutions of 2.5, 5.0, 7.5 and 10.0 wt% ammonia at 105oC for 24 h. The pretreated corn then was subjected to a conventional mashing procedure and subsequently ethanol fermentation using a commercial strain of natural Saccharomyces cerevisiae with addition of a commercial cellulase. Pretreatment of the corn with 7.5 wt% ammonia solution plus cellulase addition gave highest ethanol production, which improved the yield in fermentation using 25 wt% solid from 334 g ethanol/kg corn obtained in the control (no pretreatment and no cellulase addition) to 379 g ethanol/kg corn (a 14% increase). The process developed can potentially be implemented in existing dry-grind ethanol facilities as a “bolt-on” process for additional ethanol production from corn fiber, and this additional ethanol can then qualify as “cellulosic ethanol” by the EPA’s Renewable Fuels Standard and thereby receive RINS (Renewable Identification Numbers).

Some global difficulties in the modern period include energy storage conversion. Researchers have looked to renewable energy resources to discover long-term answers to this dilemma. Fuel cells are one example of prospective energy producing technology. Although these technologies appear to be very enticing, they are known to be expensive due to high expenses. Catalyst costs, as well as concerns concerning energy density. Pt based Electrocatalysts have traditionally been used to drive ORR and offer efficient power outputs. However, cost constraints have limited the use of these electrocatalysts, rendering them inefficient. Apart from the high price, Pt-based Electrodes are prone to time-dependent drift and CO deactivation, both of which occur gradually. Electrocatalysts deteriorate over time, reducing the efficiency of fuel cells. This is why alternative electrocatalysts are in high demand for future energy applications. This review covers the comparative study of Platinium and Non-Platinium based electrocatalyst in fuel cells, their shortcomings and recent advancement for efficient and optimized electrocatalyst.

This study investigates the use of Au-doped Pd anodic electrocatalysts on ATO support for the conversion of methane to methanol. The study involves cyclic voltammetry, in-situ Raman spectra, polarization curves, and FTIR analysis to determine the optimal composition of gold and palladium for enhancing the conversion process. The results demonstrate the potential for utilizing methane as a feedstock for producing sustainable energy sources. Pd75Au25/ATO electrode exhibited the highest OCP value, and Pd50Au50/ATO had the highest methanol production value at a potential of 0.05 V. Therefore, it can be concluded that an optimal composition of gold and palladium exists to enhance the conversion of methane to methanol. The findings contribute to the development of efficient and sustainable energy sources, highlighting the importance of exploring alternative ways to produce methanol.

This article presents new PEM fuel cell models with hexagonal and pentagonal designs. After observing cell performance improvement in these models, we optimized them. Inlet pressure and temperature were used as input parameters, and consumption and output power were the target parameters of the multi-objective optimization algorithm. Then we used artificial intelligence techniques, including deep neural networks and polynomial regression, to model the data. Next, we employed the RSM (Response Surface Method) method to derive the target functions. Furthermore, we applied the NSGA-II multi-objective genetic algorithm to optimize the targets. Compared to the base model (Cubic), the optimized Pentagonal and Hexagonal models averagely increase the output current density by 21.819\% and 39.931\%, respectively.

This review summarises the main numerical models of fuel droplet heating and evaporation (DHE) in combustion engines across the different scales by accessing the nano/micro, meso and macroscopic fluid elements. The phenomena of multi-physics, multi-scale and multi-phase fluid flow and heat transfer are fully investigated when the fuel droplet (dodecane) is heating and evaporated into a background gas (nitrogen) crossing the liquid-vapour (LV) interface, kinetic region (i.e., Knudsen layer) and the bulk regions of liquid and gas in terms of molecular dynamics (MD) simulations, kinetic theory modelling (i.e., direct numerical solutions of Boltzmann equations) and convectional fluid dynamics approach, respectively. The evaporation coefficient of fuel evaporating molecules and their velocity distributions at the LV interface derived from MD simulations formulate a new kinetic boundary condition (KBC). Moreover, a novel kinetic model considering the inelastic collision between fuel molecules alongside the new KBC enables us to describe the non-equilibrium gas dynamics of fuel vapour and gas mixture in Knudsen layer (KL). Heat and mass flux analysis of the fuel droplet under combustion engine conditions can be accurately assessed by implementing the inelastic collision between fuel molecules in KL and a temperature-dependent evaporation coefficient at the LV interface into DHE. The surface temperature of fuel droplet and its evaporation time, which play a significant role in resolving the ignition delay and hence the combustion phasing in engines, can also be well estimated. The multi-scale modelling of fuel DHE will make significantly potential input into the cleaner engine targeting the low-carbon emissions and enhance the capability of the existing computational fluid dynamics (CFD) solvers.

The peri-urban and urban forests in Greece occupy a total area of 105.353 ha. In these vulnerable ecosystems, fire constitutes a natural disaster presenting particular challenges and specific difficulties. These include the high number of visitors as well as forests characteristics - such as the presence of particularly flammable tree species and high accumulation of combustible biomass – that make the on-start of fires more likely. The main purpose of the current research is to identify the optimum combination of silvicultural treatments to efficiently reduce potential forest fire severity and to facilitate their successful suppression by firefighting crews. In order to simulate the basic fire environment of urban forests, two main experimental plots were established and several tree and topographical characteristics were measured. Additionally, the NEXUS wildfire system was used to simulate forest fire potential behavior before and after the adoption of the silvicultural treatments that altered critical characteristics of the forest fire environment. The results clearly show that specific silvicultural prescriptions altered the type of forest fire spreading potential, revealing the overall efficiency of preventing actions during forest management.

In this paper, a special recurrent neural network (RNN) called \emph{Long Short-Term Memory (LSTM)} is used to design a virtual load sensor that estimates the mass of heavy vehicles. The estimation algorithm consists of a two-layer LSTM network, with the two layers based on sequence-to-sequence and sequence-to-one logic, respectively. The network estimates the vehicle mass based on the vehicle speed, longitudinal acceleration, engine speed, engine torque, and the accelerator pedal position. The network is trained and tested with a data set collected in a high-fidelity simulation environment called Truckmaker. Training data is generated in acceleration maneuvers in a range of speeds whereas test data is obtained by simulating the vehicle in a Worldwide harmonized light vehicles test cycle (WLTC). Preliminary results show that, with the proposed approach, the heavy-vehicle mass can be estimated as accurately as commercial load sensors in a range of load mass as wide as four tons.

We give two examples of the appearance of heavy-tailed distributions in applications to social sciences. Among these distributions are the laws of Pareto, Lotka, and some new ones. The examples are illustrated by constructing suitable toy models.

The shortage of quantum computers, and their current state of development, constraints research in many fields that could benefit from quantum computing. Although the work of a quantum computer can be simulated with classical computing, personal computers take so long to run quantum experiments that they are not very useful for the progress of research. This manuscript presents an open quantum computing simulation platform that enables quantum computing researchers to have access to high performance simulations. This platform, called QUTE, relies on a supercomputer powerful enough to simulate general purpose quantum circuits of up to 38 qubits, and even more under particular simulations. This manuscript describes in-depth the characteristics of the QUTE platform and the results achieved in certain classical experiments in this field, which would give readers an accurate idea of the system capabilities.

The generalized dual-kinetic-balance approach for axially symmetric systems is employed to solve the two-center Dirac problem. The spectra of one-electron homonuclear quasimolecules are calculated and compared with the previous calculations. The analysis of the monopole approximation with two different choices of the origin is performed. Special attention is paid to the lead and xenon dimers, Pb82+–Pb82+–e− and Xe54+–Xe54+–e−, where the energies of the ground and several excited σ-states are presented in the wide range of internuclear distances. The developed method provides the quasicomplete finite basis set and allows for construction of the perturbation theory, including within the bound-state QED.

This work describes and interprets the presence of heavy minerals in the western Portuguese continental margin using a set of 78 bottom samples collected from 3 distinct areas of this margin: Porto, Aveiro and Nazaré canyon head areas. The main transparent heavy mineral suite (minerals with frequencies >10%), is composed by amphiboles (hornblende), mica (biotite), andalusite, tourmaline and garnet. A secondary suite (minerals with frequencies between 1 and 10%), is composed by pyroxene (enstatite, diopside and augite), staurolite, zircon and apatite. With very low frequency representing less than 1% we found rutile, olivine, kyanite, monazite, epidote, sphene, anatase, sillimanite and brookite. The main primary sources (igneous and metamorphic rocks) explain the presence of these minerals. However, the application of the principal component analysis, with a previous application of the centered log ratio transformation of the heavy mineral data, also stresses for the importance of the grain sorting as a process in controlling the heavy mineral occurrence. The importance of this process is mostly sustained by the distribution pattern of mica and of the most flattened amphibole grains in a way that these particles tend to have a hydraulic affinity to finer grained sediments.

Maintaining sufficient levels of plant nutrients in the soil and controlling certain heavy metals, which can be toxic to the environment, are critical to ensure sustainable agricultural production. The study aimed to assess the linkage of crop-specific agricultural practices established by farmers in the Kvemo Kartli region (Georgia) with metal accumulation in soils of agricultural lands being subject to influence from polluted irrigation water in the past. In particular, we tried to identify the primary sources of micronutrients, including iron (Fe), copper (Cu), manganese (Mn), nickel (Ni), and zinc (Zn), and toxic elements such as cadmium (Cd) and lead (Pb), and share of the contaminated irrigation water and other factors related to agricultural practices under different land uses, such as intensive and extensive arable farming, vineyards, orchards, and permanent pastures having the least disturbed soil. Based on principal component analysis, five primary sources were identified and categorized according to farmers' interviews and previous studies conducted in the region. The results showed that increased concertation of plant-available Cu, Zn, Cd and Pb were mainly associated with irrigation water and intensive use of fungicides; Fe, Mn, and Ni were closely linked to several factors, such as the mineralogical composition of soils, mineral and organic fertilizers inputs, and atmospheric deposition from diffuse sources, where exhausts from transport are probably the primary source. During our study, we attempted to differentiate irrigation water inputs from fungicides using simulation based on irrigation pattern and irrigation water quality on the one hand and fungicide application rate and their metal content on the other. The simulation revealed that the intensive application of fungicides, especially in vineyards, is more significant in enriching soils with Cu and Zn than irrigation water. Identification of factorial dependences was supported by statistical analysis and application of a number of contamination assessment methods: Contamination Factor (CF), Pollution Load Index (PLI), single-factor Pollution Index (PI), Nemerow’s comprehensive pollution index (PIN), Enrichment Factor (EF), and Geo-Accumulation Index (Igeo). Applied environmental indices indicate that the soils under the former and existing vineyards are the most enriched with Cu and Zn, highlighting the significance of agricultural practices on heavy metals accumulation in soils of agricultural lands.