Abstract: High step-up voltage gain nonisolated DC-DC converter have attracted much attention in photovoltaic, fuel cells and other renewable energy system applications. In this paper, by combining input current ripple-free boost cell with coupled-inductor voltage-doubler cell, an input current ripple-free high voltage gain nonisolated converter is proposed. In addition, passive lossless clamp circuit is adopted to recycle the leakage inductor energy and to reduce the voltage spike across the power switch. By utilizing voltage-doubler cell consisting of diode and capacitor, the voltage stress of switch is further reduced and the resonance between the leakage inductor and the stray capacitor of the output diode is eliminated. A low switch-on-resistance low-voltage-rated MOSFET can therefore be employed to reduce the conduction loss and cost. The reverse recovery loss of output diode is reduced, and the efficiency of converter can be improved. Furthermore, the proposed converter can achieve nearly zero input current-ripple and make the design of electromagnetic interference (EMI) filter easy. Steady state analysis and operation mode of the converter is performed. Finally, experimental results are presented to verify the analysis results of the proposed converter.

This article introduces a novel payload structure, which has been experimentally proven to have smaller impact force while the carried internal electronics remains intact. The study describes in details how materials and geometric structures were chosen based on information analysis. It is clarified how possible geometric structures and materials can be chosen to yield optimal efficiency. Finite element method simulations were carried out to investigate the mechanical properties of several geometric structures, which has led to the dodecahedron form. For the frame, Polylactic Acid were chosen as an optimal material. A low air pressure test for parts of the structure, and also the whole structure were carried out with successful results. Drop tests, with force measuring sensors and high speed videos, were carried out for measuring and comparing the maximal impact force of classical payloads and the novel one. Laboratory and real life tests demonstrated that the developed new structure is safer and it is applicable.

The development of accurate dynamic battery pack models for electric vehicles (EVs) is critical for the ongoing electrification of the global automotive vehicle fleet, since these serve as a key element in the energy performance of an EV powertrain system. The Equivalent Circuit Model (ECM) technique at the cell level is commonly employed for this purpose, combining accuracy and efficiency in the representation of battery operation within the broader powertrain system. In this study, a second-order ECM model of a battery cell is being developed using Modelica, an equation-based modeling language. Parameter lookup tables at multiple levels of state of charge (SoC), extracted from Li-ion battery cells with 4 different commonly used cathode materials, have been utilized. This approach allows for a representation of the battery systems that are used in a wide range of commercial EV applications. To verify the model, an integrated EV model is developed and simulation results of the FTP75 driving cycle have been compared against an equivalent application in MATLAB Simulink. The findings demonstrate a close match between the results obtained from both software across different system points. Specifically, the maximum deviation of SoC is limited to 0.08% and the maximum value of relative voltage deviation is 1.4%. The verified model enables the exploration of multiple possible architecture configurations of EV powertrains with Modelica.

Rice blast and brown planthopper (BPH) are two of the most destructive diseases and pests in rice (Oryza sativa L.) production in China. The development of multi-resistant varieties is widely recognized as the most efficient and environmentally friendly approach to controlling crop diseases and pests. Functional molecular markers (FMMs) have been developed from functional variants in the genic region associated with trait variation, greatly enhancing the efficiency of identifying and pyramiding valuable genes in crop breeding. In this study, two FMMs and a multiplex PCR amplification system were developed for two major broad-spectrum BPH resistance genes, Bph6 and Bph9. By assistance of FMMs in multi-resistant rice restorer line development pipeline, two lines (Huahui7713 and Huahui3006) with blast and BPH resistance were developed by pyramiding three resistance genes Pigm, Bph6 and Bph9. Huahui7713 and Huahui3006 as male lines, two new hybrid rice varieties (WeiLiangYou7713 and Xuanliangyou3006) were certificated and commercial released in China. WeiLiangYou7713 and Xuanliangyou3006 showed improved blast and BPH resistance, and no penalty on yield and grain-quality. Annual promotion area of WeiLiangYou7713 has exceeded 53.3 thousand hectares, indicating its widespread adoption and success in the market. Huahui7713 and Huahui3006 could have great potential for utilization in blast and BPH resistance rice breeding.

This work targets the development of a mobility control system for high-speed series hybrid electric tracked vehicles, which operate with independent traction motors for each track. The scope of the research encompasses the modeling of the series hybrid powertrain specific to military tracked vehicles, as well as an in-depth analysis of their dynamic behavior. Subsequently, the study conducts a critical review of the mobility control approaches sourced from literature, identifying key techniques relevant to high-inertia vehicular applications. Building on the foundational models, the study puts forward a robust closed-loop mobility control system aimed at ensuring precise and stable off-road vehicle operations. The system's resilience and adaptability to a variety of driving conditions are emphasized, with a particular focus on handling maneuvers such as steering and pivoting, which are challenging operations for tracked vehicle agility. The performance of the proposed mobility control system is tested through a series of simulations, covering a spectrum of operational scenarios. These tests are carried out in both offline simulation settings, which permit meticulous fine-tuning of system parameters, and real-time environments that replicate actual field conditions. The simulation results demonstrate the system's capacity to improve vehicular response and highlight its potential impact on the future designs of mobility control systems for the heavy-duty vehicle sector, particularly in defense applications.

Amid the swift progression of the global automobile industry, the aspiration for lightweight vehicle design has surfaced as a crucial approach to boost fuel efficiency and curtail environmental impact. The objective of this study revolves around achieving holistic optimization of vehicle structure via detailed scrutiny of vehicle process characteristics, amalgamated with a Back Propagation neural network (BPNN) optimized by a genetic algorithm (GA) and a topology optimization (TO) method.The process initiates with an examination of the vehicle's technical characteristics, succeeded by an optimization protocol that couples GA with BPNN. This exhaustive optimization procedure derives the best-fit values of design parameters and identifies the globally optimal lightweight design approach. Subsequently, a comprehensive structural optimization is actualized by modifying the topological distribution of the structure.A simulation experiment of the conceptual car body beam skeleton is conducted as a conclusive step, and the anti-collision capacity of the car body beam skeleton is assessed by measuring deformation intrusion. The findings reveal that in the vehicle topology optimization, a comparative analysis of pre and post-optimization results indicates an improved topological density across diverse sections. The topological density of the vehicle's frontal structure escalates from 0.75 to 0.8. Following optimization, the stiffness assessment records a marginal increase (within the range of 0.02–0.05), implying that the lightweight design does not compromise the general rigidity of the structure.The optimized body structure manifests superior crashworthiness in the crash test: the deformation intrusion diminishes by 27% in front-end collisions. In side impacts, the deformation and intrusion at critical points are reduced by 13.15% to 10% respectively. The comprehensive method proposed herein proves to be an efficient strategy to actualize the lightweight design of vehicles.

In the modern power grid, characterized by the increased penetration of power electronics and extensive utilization of renewable energy, inverters-based power plants play a pivotal role as the principal interface of renewable energy sources (RESs) and the grid. Considering the stability characteristics of grid-following (GFL) inverters when the grid is relatively weak, the application of grid-forming (GFM) controls becomes imperative to enhance the stability of the entire power plant. Thus, there is an urgent need for suitable and effective models to study the interaction and stability of the paralleled inverters employing GFL and GFM controls. Thus, the small-signal modeling with full-order state space model and eigenvalues analysis is presented in this paper. First, the small-signal state-space model of the individual GFL and GFM inverters is obtained considering the control loop, interaction, reference frame, transmissions, and time delays. Then, the models of the individual inverter are extended to the hybrid inverters to study the effects of the GFM inverters on the small- signal stability of the entire system. And, the impacts of the inertia and damping are analyzed by the eigenvalues of the state-transition matrix. Case comprising three parallel GFL inverters and two GFL inverters with one GFM inverter, respectively, are studied to examine the effectiveness and accuracy of the model. Finally, the stability margin obtained from the eigenvalue analysis of the entire system is verified by time-domain simulations.

Based on the dynamic strength variation mechanism of concrete under complex loading conditions, two approaches were devised: numerical testing and CT scanning, guided by the principle of minimizing energy dissipation. A methodology for calculating concrete's failure area and measuring its strength was developed. The analysis delves into the mechanisms behind failure patterns and variations in concrete specimen strength, focusing on crack initiation, development, and the resultant failure surface formed by crack propagation, along with the stress distribution in concrete specimens subjected to diverse loading conditions. Through evaluating the strength and computed failure area of concrete specimens, it is evident that the loading method influences both the strength and failure area of concrete specimens. In general, a larger failure area correlates with a higher measured strength.

Abstract: This study investigates the effect of Electric Vehicle Charging Stations (EVCS) on light-duty Electric Vehicle sales and the Total California rebates. Electric Vehicle Charging Stations (EVCS) are infrastructure facilities that allow for the charging of electric vehicles (EVs). I applied the before and after model with California state county using its community-level attributes and used the difference-in-difference design to identify a strategy for estimating the causal effects of these attributes. These attributes include EVCS installations by time, EV sales by time, rebate applications by time, the number of multi-unit housing units, and the median income levels. The empirical ev-idence of this study shows the estimated relationship between public EV charging installation and EV sales overall by community income level, housing density, and other relevant factors, the result shows that EVCSs is highly correlated with light duty Electric Vehicle adoption. For the investors, policymakers, and other stakeholders, this study provides evidence of a threshold of EVCS on Light Duty Electric Vehicle adoption and rebate in California.

Natural gas hydrate, also known as combustible ice and mainly composed of methane, it is identified as the potential clean energy in the 21th century. Due to its large reserves, gas hydrate can ease problems caused by energy resource shortage and has gained attention around the world. In this paper, we focus on the exploration and development of gas hydrate as well as discussing its status and future development trend in China and abroad, then we analyze its opportunities and challenges in China from four aspects: resource, technology, economy and police with five forces model and PEST method. The results show, China has abundance gas hydrate resource; however the backward technologies and inadequate investment has seriously hindered the future development of gas hydrate, so China should establish relevant cooperation framework and intuitional arrangement to attract more investment as well as breaking through technical difficulties to make gas hydrate commercialization as soon as possible.

Efficient processing of end-of-life lithium-ion batteries of electric vehicles is important and a pressing challenge for a circular economy. Regardless of whether the processing strategy is recycling, repurposing or remanufacturing, the first processing step would usually involve disassembly. As battery disassembly is a dangerous task, efforts have been made to robotise it. In this paper, a robotic disassembly platform using four industrial robots is proposed to automate the non-destructive disassembly of a plug-in hybrid electric vehicle battery pack into modules. The work was conducted as a case study to demonstrate the concept of autonomous disassembly of an electric vehicle battery pack. A two-step object localisation method based on visual information is used to overcome positional uncertainties from different sources and is validated by experiments. Also, the unscrewing system is highlighted, and its functions, such as handling untightened fasteners, loosening jammed screws, and changing the nutrunner adapters with square drives, are detailed. Furthermore, the time required for each operation is compared with that taken by human operators. Finally, the limitations of the platform are reported and future research directions are suggested.

The meticulously engineered powertrain mounting system of hybrid-electric vehicles plays a critical role in minimizing vehicle vibrations and noise, thereby enhancing the longevity of vital powertrain components. However, developing and designing such a system demands substantial time and financial investments due to intricate analysis and modeling requirements. To tackle this challenge, this study integrates data-mining technology into the design and optimization processes of the powertrain mount system. The research focuses on the powertrain mounting system of a transverse four-cylinder hybrid-electric vehicle, employing the CRISP-DM (Cross-Industry Standard Process for Data Mining) methodology to establish a data-mining prediction model for mounting stiffness. This model utilizes three data mining algorithms—Multi-SVR, MRTs, and MLPR—assessing their predictive accuracy concerning mounting system stiffness estimation. A comparative analysis reveals that the MRTs algorithm outperforms others as the most effective prediction model. The proposed predictive model elucidates the quantifiable correlation between vibration isolation performance and installation stiffness, overcoming complexities associated with traditional modeling approaches. Applying this model in powertrain mounting system design showcases the efficacy of the CRISP-DM-based approach, significantly enhancing design efficiency without compromising prediction accuracy.

Reasonable allocation of production plans and saving the overall electricity cost are crucial for large manufacturing conglomerates, which is an effective way for conglomerates to realize open-source and cost-saving. This paper develops an optimization model of off-site industrial production scheduling for enterprises in response to the problems of high electricity costs due to the irrational allocation of production schedules on the demand side of China's electric power and the difficulty of promoting industrial and commercial distributed photovoltaic (PV) projects in China. The model makes full use of the conditions of different PV resources and different electricity prices in different places to optimize the scheduling of industrial production in different places. The model is embedded with two sub-models of the electricity price prediction model and distributed photovoltaic kWh cost model to complete the model parameters, in which the electricity price prediction model utilizes the LSTM neural network. The integrated model is then solved by the particle swarm algorithm. To verify the effectiveness of the model in solving the problem of off-site production scheduling on the demand side of electricity, the research team researched two off-site pharmaceutical factories belonging to the same large pharmaceutical company. Finally, the research data were substituted into the model for solving, and it was concluded that the optimization model could significantly reduce the cost of electricity consumption of the enterprise by about 7.9 %.

The widespread adoption of electromobility constitutes one of the measures designed to reduce air pollution caused by traditional fossil fuels. However, several factors are currently impending this process, ranging from insufficient charging infrastructure, battery capacity, long queueing and charging time, to psychological factors. On top of range anxiety, the frustration of the EV drivers is further fueled by the lack the uncertainty of finding an available charging point on their route. To address this issue, we propose a solution that comes to bypass the limitations of the Reserve now function of the OCPP standard, enabling drivers to make charging reservations for the upcoming days, especially when planning a longer trip. We created an algorithm that generates reservation intervals based on the charging station's reservation and transaction history. Subsequently, we ran a series of test cases that yielded promising results, with no overlapping reservations.

Accurate forecasting of icing thickness has a great significance for ensuring the security and stability of power grid. In order to improve the forecasting accuracy, this paper proposes an icing forecasting system based on fireworks algorithm and weighted least square support vector machine (W-LSSVM). The method of fireworks algorithm is employed to select the proper input features with the purpose of eliminating the redundant influence. In addition, the aim of W-LSSVM model is to train and test the historical data-set with the selected features. The capability of this proposed icing forecasting model and framework is tested through the simulation experiments using real-world icing data from monitoring center of key laboratory of anti-ice disaster, Hunan, South China. The results show that the proposed W-LSSVM-FA method has a higher prediction accuracy and it may be a promising alternative for icing thickness forecasting.

In the permanent magnet synchronous motor (PMSM) drive system, the unwilling and ear-piercing vibro-acoustics caused by high-frequency sideband harmonics becomes unacceptable in the electric vehicle application. In this paper, a modified space vector pulse-width modulation (SVPWM) technique implemented with hybrid carrier frequency modulation (HCFM) is provided to reduce the sideband current harmonic components and vibro-acoustic responses. The principle and implementation of the proposed HCFM technique are firstly presented, in which the fixed carrier frequency is improved with the sawtooth and random signal-based coupling modulation based on the rotor position. For verification, the experiment tests are carried out on a prototype 12/10 PMSM and microcontroller unit. The effectiveness of the HCFM technique can hence be confirmed, in which the sideband vibro-acoustics reduction shows more effectively than that in conventional random PWM. The proposed approach may provide a new route in noise-cancelling and electromagnetic compatibility for the electric drive powertrain.

This paper analyzes and compares models for predicting average magnet losses in interior permanent-magnet motors with fractional-slot concentrated windings due to harmonics in the armature reaction (assuming sinusoidal phase currents). Particularly, loss models adopting different formulations and solutions to the Helmholtz equation to solve for the eddy currents are compared to a simpler model relying on an assumed eddy-current distribution. Boundaries in terms of magnet dimensions and angular frequency are identified (numerically and using an identified approximate analytical expression) to aid the machine designer whether the more simple loss model is applicable or not. The assumption of a uniform flux-density variation (used in the loss models) is also investigated for the case of V-shaped and straight interior permanent magnets. Finally, predicted volumetric loss densities are exemplified for combinations of slot and pole numbers common in automotive applications.

Open source software such as OpenDSS has given a lot of help to distribution network researchers and educators. With high penetration of distributed renewable energy resources into distribution network, tradition distribution steady state analysis software such as OpenDSS is faced with difficulty in handling distributed generators. Three-phase distributed generators are often modeled in sequence frame while unbalanced distribution network are usually modeled in phase frame. So a load flow in sequence-phase coupled frame is proposed to handle models described in both frames. Voltage controlled DGs which are difficult to cope with in OpenDSS are handled in proposed program. The steady state analysis platform is programmed with open source Modelica language and the main aim of this paper is to introduce an open source platform for active distribution network steady analysis include load flow and short circuit analysis which can be easily adopted and improved by other educators and researchers.

Coal gasification with carbon dioxide is a process for generating clean gaseous fuels and relieving greenhouse effect. Zhundong coal has high alkali and alkali earth metals (AAEMs) content, medium volatile and low ash in nature. Isothermal CO₂ gasification of char derived from Zhundong coal (R-char) and char from acid washing R-char (AR-char) are performed in thermo-gravimetric analyzer (TGA). The effect of AAEMs is investigated on the gasification behavior in the range of temperatures 1073 K to 1273 K. The carbon conversion increases rapidly with increasing reaction temperature and CO₂ concentration. R-char has high gasification rate and carbon conversion compared with AR-char. The accuracy of the free-model approach for calculating activation energy at different conversions is validated by compared with different kinetic models (volume reaction model, distributed activation energy model). Moreover, R-char gasification with CO₂ shows a compensation effect as the Arrhenius parameters (EA and k0) increase or decrease simultaneously.

Energy storage systems play a crucial role in the overall performance of hybrid electric vehicles. Therefore, the state of the art in energy storage systems for hybrid electric vehicles has been discussed in this paper along with appropriate background information for facilitating future research in this domain. Specifically, we have compared the key parameters such as cost, power density, energy density, cycle life, and response time for various energy storage systems. For the energy storage systems employing ultra capacitors, we have presented the characteristics such as cell voltage, cycle life, power density and energy density. Furthermore, we have discussed and evaluated the interconnection topologies for the existing energy storage systems. We have also discussed the hybrid battery-flywheel energy storage system as well as the mathematical modeling of the battery-ultracapacitor energy storage system. Toward the end, we have discussed energy efficient powertrain for hybrid electric vehicles.

Electric vehicles (EVs) play a significant role in reducing carbon emissions. In the US, EVs are mostly owned by multi-vehicle households, and their usage is primarily studied in the context of vehicle miles traveled. This study takes a unique approach by analyzing EV usage through the lens of vehicle choice (between EVs and internal combustion engine vehicles) within multi-vehicle households. A two-step machine-learning framework (clustering and decision trees) is proposed. The framework determines the preferred trip category for EV use and captures the effects of household attributes, driver attributes, built-environment factors, and gas prices on EV use in multi-vehicle households. Results indicate that discretionary trips (accumulated local effect = 0.037) are mostly preferred for EV use. EV preference is more pronounced among households with fewer workers (<2) and lower income levels. These findings are valuable for policymakers and auto manufacturers in targeting specific market segments and promoting EV adoption.

This paper proposes an electric vehicle routing problem with considering states of charging stations and suggests solution strategies. Charging of electric vehicles is a main issue in the field of electric vehicle routing problem. There are many studies to find locations of charging stations, recharging functions for batteries of vehicles, and so on. However, states of charging stations significantly affect the routes of electric vehicles, which is not much explored. The states may include open or close of charging stations, occupied or empty of charging slots, and so on. This paper investigates how the states of charging stations are estimated and routing strategies are determined. We formulate a mixed integer programming model and suggest how to solve the problem with exact method. Numerical examples provide the optimal routing strategies of electric vehicles in the changing environments of the states of charging stations.

Hybrid electric vehicles are certainly one of the key solutions for improving fuel efficiency and reducing emissions, especially in special vehicle application and with the use of CO2 neutral fuels. Determining the energy management strategy and finding the optimal solution with regard to the aforementioned goals re-mains the one of the main challenges in the design of HEV. This paper presents a new vehicle modeling method, with an emphasis on HEVs, which is based on the frequency analysis of emissions and consumption according to the current specific traction power of the vehicle. The evaluation of the newly introduced model in the RDE, NEDC and WLTP cycle was performed and the results were compared with the standard verified vehicle model that was created in AVL's CruiseM software package. Positive traction energies have positive deviations of between 0.35% and 2.85%. The largest deviation in CO2 emissions was recorded for the HEV model in the RDE cycle and in the non-hybrid model in the WLTP cycle of 3.79% and 4.4% respectively, all other combinations of cycle and vehicles had deviations of up to about 1%. As expected, the largest relative deviations were recorded for NOx emissions from 0.13% to 9.62% for HEV in the WLTP cycle.

The article studies and analyzes a hybrid power source system, lithium battery, and fuel cell assisted by flexible photovoltaic panels for hybrid electric vehicles (HEVs). The new configuration operates based on optimizing the performance of the dual power source to maximize the available energy and operating time. The operational mode simulates specific driving conditions in urban, peripheral, and intercity routes under variable driving patterns and traffic conditions. The simulation results show that the new configuration increases the hybrid electric vehicle performance, providing higher reliability despite the more complex design. The proposed system reduces the external power supply dependence and avoids unexpected sudden stops due to energy exhaustion. The new configuration also extends the vehicle driving range depending on driving mode and route conditions. The vehicle driving range extension may reach up to 276.3 km. The hybridization of fuel cells with lithium battery and PV panel assistance enhances battery management, reducing battery servicing and increasing lifespan. The proposed topology is cheaper than a single fuel cell power system by 17.2%, reducing the total cost related to the single battery power system if we consider the battery recharge for its entire lifespan. The cost saving is 2.6% for the American market and 14.8% for the European one.

This article investigates the source of booming noise emanating from the tailgates of electric vehicles, along with proposed strategies to mitigate it. This study involved the measurement of booming noises during on-road vehicle tests to pinpoint their origins. Additionally, operational deflection shapes (ODS) were extracted from the tailgate vibration signals to gain insight into its dynamic behavior. Modal tests were conducted on the tailgate to determine its dynamic characteristics and compared with driving test results to reveal the mechanism responsible for tailgate-induced booming noise. It was established that such noise is primarily due to the tailgate modes resulting from a combination of rigid body motion in the fore-aft direction and deformation in the central section of the panel. An analytical model of the tailgate was developed using commercial finite element analysis software to propose measures for reducing booming noise. Experimental findings validated the model accuracy. Structural enhancements were implemented to enhance the panel stiffness and improve the connection between the vehicle and tailgate via bushings to dampen the booming noise resulting from tailgate motion. Under random force inputs, analytical results demonstrated a 13.8% reduction in maximum deformation in the tailgate model in the improved structural configuration with increased panel stiffness.

We consider the problem of coordinating the charging of an entire fleet of electric vehicles (EV), using a model-free approach, i.e. purely data-driven reinforcement learning (RL). The objective of the RL-based control is to optimize charging actions, while fulfilling all EV charging constraints (e.g. timely completion of the charging). In particular, we focus on batch-mode learning and adopt fitted Q-iteration (FQI). A core component in FQI is approximating the Q-function using a regression technique, from which the policy is derived. Recently, a dueling neural networks architecture was proposed and shown to lead to better policy evaluation in the presence of many similar-valued actions, as applied in a computer game context. The main research contributions of the current paper are that (i)we develop a dueling neural networks approach for the setting of joint coordination of an entire EV fleet, and (ii)we evaluate its performance and compare it to an all-knowing benchmark and an FQI approach using EXTRA trees regression technique, a popular approach currently discussed in EV related works. We present a case study where RL agents are trained with an epsilon-greedy approach for different objectives, (a)cost minimization, and (b)maximization of self-consumption of local renewable energy sources. Our results indicate that RL agents achieve significant cost reductions (70--80%) compared to a business-as-usual scenario without smart charging. Comparing the dueling neural networks regression to EXTRA trees indicates that for our case study's EV fleet parameters and training scenario, the EXTRA trees-based agents achieve higher performance in terms of both lower costs (or higher self-consumption) and stronger robustness, i.e. less variation among trained agents. This suggests that adopting dueling neural networks in this EV setting is not particularly beneficial as opposed to the Atari game context from where this idea originated.

Three kinds of inorganic alkali are introduced into tetraethylenepentamine (TPEA) and polyethyleneimine (PEI) modified MCM-41 as the CO2 adsorbents. FT-IR and TGA are used to characterize the surface groups and the thermal stability of adsorbents. Chemical titration method is used to measure the alkali amounts of adsorbents. Thermo-gravimetric analysis with 10%CO2/N2 as the simulated flue gas is used to test the CO2 adsorption performance of adsorbents. The results show that all three kinds of inorganic alkali containing adsorbents exhibit promoted CO2 adsorption capability than traditional TPEA and PEI modified samples. Ca(OH)2 and PEI modified samples exhibit the highest adsorption capacity and stable regeneration property. The introduction of inorganic alkali changes the chemical adsorption mechanism between CO2 and increases the effective alkali amounts due to its hydroxyl groups. The CO2 adsorption capacities have a linear dependence relation with the alkali amounts of adsorbents, indicating that alkali amount is a critical factor for novel adsorbents exploring.

More and more works are using machine learning techniques while adopting supervisory control and data acquisition (SCADA) system for wind turbine anomaly or failure detection. While parameter selection is important for modelling a wind turbine’s health condition, only a few papers have been published focusing on this issue and in those papers interconnections among sub-components in a wind turbine are used to address this problem. However, merely the interconnections for decision making sometimes is too general to provide a parameter list considering the differences of each SCADA dataset. In this paper, a method is proposed to provide more detailed suggestions on parameter selection based on mutual information. Moreover, after proving that Copula, a multivariate probability distribution for which the marginal probability distribution of each variable is uniform is capable of simplifying the estimation of mutual information, an empirical copula based mutual information estimation method (ECMI) is introduced for an application. After that, a real SCADA dataset is adopted to test the method, and the results show the effectiveness of the ECMI in providing parameter selection suggestions when physical knowledge is not accurate enough.

For offshore wind power generation, accessibility is one of the main factors that has great impact on operation and maintenance due to constraints on weather conditions for marine transportation. This paper presents a framework to explore the accessibility of an offshore site. At first, several maintenance types are defined and taken into account. Next, a data visualization procedure is introduced to provide an insight into the distribution of access periods over time. Then, a rigorous mathematical method based on finite state Markov chain is proposed to assess the accessibility of an offshore site from the maintenance perspective. A five-year weather data of a marine site is used to demonstrate the applicability and the outcomes of the proposed method. The main findings show that the proposed framework is effective in investigating the accessibility for different time scales and is able to catch the patterns of the distribution of the access periods. Moreover, based on the developed Markov chain, the average waiting time for a certain access period can be estimated. With more information on the maintenance of an offshore wind farm, the expected production loss due to time delay can be calculated.

The abrupt increase of the electric vehicles in Bangladesh needs huge amount of power. As a result, alternative energy sources are emphasized due to limited fossil fuels in order to develop a sustainable energy sector with environment friendly resources. Bangladesh has an enormous potential in the field of renewable resources like biogas and biomass. This paper presents 20 kW electric vehicle charging station (EVCS) utilizing biogas resources where maximum energy requirement is 100 kWh. In this paper, the biogas based EVCS is designed using MATLAB Simulink and HOMER software. Daily 15-20 electric vehicles can be recharged their batteries using the proposed charging station. The proposed system offers lower cost of energy compared to the grid electricity. Moreover, the proposed charging station shows 68.75% reduction in CO₂ emission than grid based charging station. In addition, the proposed EVCS will save monthly $ 16.25 and $ 27.50 respectively for easy bike and auto rickshaw type electric vehicles in Bangladesh.

With the continuous improvement and observable benefits of electric vehicles (EVs), major logistic companies are introducing more EVs into their conventional fleets. This gives rise to a new type of vehicle routing problem with mixed vehicles, where heterogeneous internal combustion vehicles (ICVs) and electric vehicles are considered in route planning. In addition, certain deliveries that are not efficient on any type of vehicles, are outsourced to third-party common carriers. In this paper, we define this problem as a mixed vehicle routing problem with common carriers (MVRPC). The objective of such problems is to minimize the transportation costs by considering routes with ICVs and EVs, the possibility of visiting recharging stations, outsourcing options, and drivers’ layover regulations. This variant of the vehicle routing problems has many practical applications, particularly in the design of long-haul transportation and last-mile delivery services. Effective MVRPC solutions play a key role in promoting the going Green image and optimally allocating resources. The problem has received limited attention in the literature likely because addressing all the needed aspects is especially challenging. To solve the large-scale problem, we develop a branch-and-cut pricing framework that relies on strong cuts and customized labeling algorithms. Numerical experiments highlight the effectiveness of our algorithm. This success can be attributed to tailored critical resources, dynamically bounded bidirectional labeling procedures, strong dominance criteria, and implementation strategies.

The work aims to improve the battery performance in hybrid electric vehicles (HEVs) by reducing the vehicle speed. We develop a specific protocol for managing battery use and optimizing the energy consumption rate to achieve this goal. The protocol automatically controls the driving operation, avoiding incompatible driving patterns with energy-saving mode and performance improvement. The protocol is submitted to a simulation process to predict the energy rate lowering and battery performance enhancement. The proposed protocol applies to any hybrid electric vehicle type and route conditions since it uses vehicle mass, drag and rolling coefficients, and road slope as variable parameters to determine the minimum energy consumption rate. We run experimental tests to validate the simulation data and the proposed protocol. Furthermore, the protocol applies to variable starting vehicle speeds, from 10 to 50 km/h, corresponding to the current driving patterns, sport, normal, and eco, set up by car manufacturers. A reduction of 10% in vehicle speed in urban and peripheral routes achieves a minimum energy rate, enhancing battery management. Current vehicle speed shows a deviation from optimum management of 18% while applying the vehicle speed reduction limits the deviation to 0.2%. Experimental results show a good agreement with simulation data with 94% accuracy. We tested the protocol for urban and peripheral routes with maximum vehicle speed limits of 60 and 90 km/h.

In this paper, we examined the temperature variations of key constituents during the operational cycle of a custom-built electric vehicle. The vehicle was made employing a motor of 10kW, a KLS7275D controller, and a lithium-ion battery. Temperature sensors for monitoring was affixed to the motor, controller, and battery, facilitating a comprehensive analysis of thermal behaviors. A controlled 20 minute driving tests encompassing both high and low speeds were executed to scrutinize temperature variations. Our findings reveal that the controller exhibited the most substantial temperature fluctuation compared to the battery and motor. Results shows the importance of thermal management strategies for components to ensure optimal driving performance and component reliability in electric vehicles.

China’s leading development of a complete battery value chain for Electric Vehicles (EV) is restructuring the global automotive sector. The competitive advantage of China's EV battery industry lies on its firms’ core competency and political economic geography. Based on first-hand empirical material and data obtained from years of fieldwork in an EV battery cluster in South China, this paper identifies what the Chinese EV battery industry’s core competency is and details how it is built up from below. The current core competency of Chinese battery firms is their mass manufacturing capability to supply lithium-ion batteries vehicle manufacturers (OEMs) with stable and consistent quality as well as competitive prices. This competency is acquired by firms through technological learning at workshop level while taking use of their experiences accumulated in mass production of batteries for consumer electronics sectors. Furthermore, the rapid learning and accumulation of knowledge on battery manufacturing at large scale is also facilitated by the industrial cluster environment where firms are embedded. Supported and promoted by local government policies, Chinese EV battery clusters are composed of firms from different segments of a complete battery value chain. The findings illuminate the likely strategic strengths, weaknesses, and futures of the Chinese EV battery industry in global competition.

The current study investigated the use of two-dimensional spatial distribution mapping representing the chlorophyll-a level in a river generated via an unmanned aerial vehicle (UAV) and an unmanned surface vehicle (USV). A domestically developed UAV (Remo-M, Uconsystem Inc., Korea) and a USV developed by our research team were used to collect data from the Nae Seong stream in Korea. An adaptation of the “Data Cleaner” tool was developed and used for USV data processing and analysis. The operation of the autonomous USV was successful. Four previously described indices for quantifying algal blooms in rivers were utilized to create chlorophyll-a images, the normalized difference vegetation index (NDVI), the normalized green red difference index, the green normalized difference vegetation index (GNDVI), and the normalized difference red edge index. The suitability of the linear regression analysis of the correlation between the spectral indices obtained using the UAV and the in situ chlorophyll-a data obtained using the USV was evaluated with the coefficient of determination (R2) at a significance level of p &lt; 0.001. In field application and correlational analysis the NDVI was strongly correlated with chlorophyll-a (R2 = 0.88, p < 0.001), and the GNDVI was moderately correlated with chlorophyll-a (R2 = 0.74, p < 0.001). The map of chlorophyll-a was successfully quantified using the UAV and USV hybrid platforms.

Disassembly is a pivotal technology to enable the circularity of electric vehicle batteries by applying circular economy strategies that extend the life cycle of their components, like remanufacturing and repurposing, or by using efficient recycling to reintegrate the gained materials in producing new battery systems. This paper aims to develop a multi-method self-configuring simulation model for investigating disassembly scenarios while considering the battery design as well as the configuration and layout of the disassembly station. We demonstrate the developed model in a case study using a battery of Mercedes-Benz and the automated disassembly station of the project DeMoBat at Fraunhofer IPA. Furthermore, we introduce two disassembly scenarios, the component-oriented and the accessibility-oriented disassembly, and compare them using the simulation model to determine several indicators, such as the frequency of tool change, the number and distribution of robot routes, the tool utilization, and the disassembly time.

The results shown in this paper extend our research group's previous work, which presents the theoretically achievable hydrogen engine-out NOx (H2-NOx) Pareto front of a hydrogen hybrid electric vehicle (H2-HEV). While the Pareto front is calculated offline, which requires significant computing power and time, this work presents an online-capable algorithm to tackle the energy management of a H2-HEV with explicit consideration of the H2-NOx trade-off. Through the inclusion of realistic predictive data on the upcoming driving mission, a model predictive control algorithm (MPC) is utilized to effectively tackle the conflicting goal of achieving low hydrogen consumption while simultaneously minimizing the NOx. In a case study it is shown that the MPC is able to satisfy user-defined NOx limits over the course of various driving missions. Moreover, a comparison to the optimal Pareto front highlights the MPC's ability to achieve close-to-optimal fuel-performance for any desired cumulated NOx target on four realistic routes for passenger cars.

The transportation industry is rapidly transitioning from Internal Combustion Engine (ICE) based vehicles to Electric Vehicles (EVs) to promote clean energy. However, large-scale adoption of EVs can compromise the reliability of the power grids by introducing large uncertainty in the demand. Demand response with a controlled charge scheduling strategy for EVs can mitigate such issues. In this paper, a deep reinforcement learning- based charge scheduling strategy is developed for individual EVs by considering user’s dynamic driving behavior and charging preferences. The temporal dynamics of user’s anxiety about charging the EV battery is rigorously addressed. A dynamic weight allocation technique is applied to continuously tune user’s priority for charging and cost-saving with respect to charging duration. The sequential charging control problem is formulated as a Markov decision process, and an episodic approach to the deep deterministic policy gradient (DDPG) algorithm with target policy smoothing and delayed policy update techniques is applied to develop the optimal charge scheduling strategy. A real-world dataset that captures user’s driving behavior, such as arrival time, departure time, and charging duration, is utilized in this study. The extensive simulation results reveal the effectiveness of the proposed algorithm in minimizing energy cost while satisfying user’s charging requirements.

The purpose of this research is to present a thorough evaluation of the energy management system, which consists of hybrid energy storage systems, and its control algorithms, which may be used in electric vehicles. This paper outlines the characteristics of electric vehicles, research methods, analysis of the hybrid energy storage system architecture, converter topology, and energy management techniques. The strength and co-occurrence of keywords over the past ten years are shown in this study using a systematic research framework for performing a literature review and using keyword analysis techniques. The study reveals a pattern of recently and frequently used terms in works of literature. Consequently, their suitability, benefits, and drawbacks are assessed. In this study, the hybrid energy storage system and converter circuit architecture are evaluated and rated. Non-isolate DC-DC converter converter connected to SC is a suitable configuration for the hybrid converter because it is simple to build, reliable, and has minimal loss/weight/cost, which improves vehicle performance. In terms of the application of control strategies, it is shown that deterministic and fuzzy rule-based control techniques are successfully assessed using real-scale vehicle experiments and selected for manufacturing. On the other hand, real-time optimization-based energy management techniques have been effectively shown in lab-scale tests and may be used in a future real-scale vehicle.

Two-wheeler vehicles are the most significant mode of transportation for Kenyans in both rural and urban regions thereby contributing to local air pollution, and greenhouse gas emissions (GHG). The transition to electric two-wheeler vehicles can make a significant contribution to reducing GHG and improving the socio-economic lives of people living in rural Kenya. Re-newable energy systems can considerably contribute to the charging of electric two-wheeled vehicles, thus leading to the reduction of carbon emissions and the expansion of renewable energy penetration in rural Kenya. Therefore, this paper focuses on integrating and modelling electric two-wheeled vehicles (e-bikes) into an off-grid photovoltaic Water-Energy Hub located in the Lake Victoria Region of Western Kenya using the Conventional and Renewable Energy Opti-mization (CARNOT) Toolbox in MATLAB / Simulink. Electricity demand data obtained from the Water-Energy Hub was investigated and analysed. Potential solar energy surplus was identified and electric two-wheeler vehicles were integrated based on the surplus. A field measurement investigation on the energy consumption of the electric two-wheeler vehicles based on the rider’s driving behaviour was also carried. The annual electricity demand of 27,267 kWh, photovoltaic (PV) electricity production of 37,785 kWh with an electricity deficit of 370 kWh were obtained from the simulation results. To reduce the electricity deficit, a load optimisation algorithm was de-veloped to optimally integrate the electric 2-wheeler vehicle into the Water-Energy Hub. It was found that using the load optimisation algorithm, the annual electricity deficit was reduced to 1 kWh and the annual electricity demand was increased by 11% (30,767 kWh) which is enough to charge 4 additional electric two-wheeler batteries daily.

South Korea proposed reducing greenhouse gas emissions by 37% compared to the expected emissions by 2030 as the POST-2020 greenhouse gas reduction target. Electric vehicle distribution in the public sector is essential to achieve the carbon dioxide reduction target for transportation. In particular, when buses with internal combustion engines, which travel long distances and contribute substantially to greenhouse gas emissions, are replaced with electric buses, it is expected that greenhouse gas emissions will be significantly reduced. There are three types of electric buses with different power supply systems: a plug-in type in which power is supplied when a plug is inserted, a battery-swapping type in which a battery mounted on top of the vehicle is swapped at a swapping station, and a wireless type in which the battery is wirelessly charged through self-induction at a charging facility installed on the road. Vehicles of each charging type have different advantages and disadvantages. The performance, charging type, battery capacity, and operating environment of electric buses are mutually related parameters that must be considered when introducing such vehicles. Therefore, the optimal charging type must be selected according to the operating environment to enable the widespread use of electric buses. As such, this report proposes the optimal charging type according to the operating environment of public-sector electric vehicles.

Navigation is the most challenging issue in autonomous vehicles. Researchers in the current era have developed many Artificial Intelligence techniques to navigate, generate paths, and avoid obstacles for optimum path planning for autonomous vehicles. Different studies have investigated bio-inspired techniques to overcome the navigation issue, including obstacle avoidance. This paper uses new meta-heuristic optimization techniques called Dragonfly Algorithm (DA) to set the goal by detecting and avoiding obstacles with minimum human interference. For effective results, the Dragonfly-Fuzzy hybrid algorithm is analyzed over the unstructured environment because individual techniques may not be sure of an optimal solution over all configurations. The main advantage of the proposed hybrid controller is that it combines the multiple features of different approaches into a single controller. This paper compares simulation and experimental findings over various environmental conditions to the individual algorithm. Regarding time and path optimization, the hybrid Dragonfly-Fuzzy controller performs better than the respective controller.

Battery-powered electric vehicles (EVs) have emerged as an environmentally friendly and efficient alternative to traditional internal combustion engine vehicles, while their single-charge driving distances under cold conditions are significantly limited due to the high energy consumption of heating systems. Heat pumps can provide an effective heating solution for EVs, but their coefficient of performance (COP) is hampered by heat transfer deterioration due to frost accumulation. This study proposes a solution to this issue by introducing a microchannel heat exchanger (MHE) with superhydrophobic surface treatment (SHST) as a heat pump evaporator. A computational-fluid-dynamics MHE model and a dynamic heat pump model are developed and rigorously validated to examine the detrimental impact of frost accumulation on heat transfer, airflow resistance, and heat pump performance. When the frost layer thickness is 0.8 mm at a given air-side velocity of 1.0 m/s, the air-side heat transfer coefficient can be reduced by about 75%, and the air-side pressure drop sharply increases by 28.4 times. As frost thickness increases from 0 to 0.8 mm, the heating effect drops from 3.97 to 1.82 kW, and the system COP declines from 3.17 to 2.30. Experimental results show that the frost thickness of the MHE with SHST reaches approximately 0.4 mm after 30 minutes, compared to that of 0.8 mm of the MHE without SHST, illustrating the defrosting capability of the superhydrophobic coating. The study concludes by comparing the performance of various heating methods in EVs to highlight the advantages of SHST technology. As compared to traditional heat pumps, the power consumption of the proposed system is reduced by 48.7% due to the defrosting capability of the SHST. Moreover, the single-charge driving distance is extended to 327.27 km, an improvement of 8.99% over the heat pump without SHST.

Under the goal of carbon peak and carbon neutrality, the carbon emission reduction of the automobile industry has attracted more and more attention in recent years. Electric vehicle has the dual attributes of power load and energy storage unit. With the increase of the number of electric vehicles, reducing carbon emissions through the collaborative interaction between electric vehicle and power network will become an important way to control carbon emissions in the automotive field. In this study, an optimization model of emission reduction benefits based on integrated development of electric vehicle and power grid is proposed, which explores the best technical way of synergy between power grid and electric vehicle, achieves the best carbon reduction effect and provides a model basis for large-scale demonstration application. Numerical simulations based on the real case in Beijing are conducted to validate the effectiveness of the proposed method.

Nowadays, all the stakeholders, policy makers, regulators, aircraft designers, producers, operators, etc.) are intensively working on development of the aircraft with full electric and hybrid propulsion systems. However, the technical, technological constrains (like limit on accumulator energy density) require introducing a new approach to conceptual design of such aircraft. The new methods is based on energy and mass balance evaluation. This paper analyses the identified constrains; integrates the energy and mass balance equations into the preliminary definition and calculations of the aircraft performance. By this way, the technological constrains might be transferred into the limitation on the aircraft energy and mass breakdown, that initiates a new approach to aircraft conceptual design uses the knowledge based multidisciplinary optimization. The paper describes the developed methodology for conceptual design of aircraft. It show results of implementing this new development philosophy to conceptual design of a four-seat small electric/hybrid aircraft and a special hybrid cargo UAV. The discussion of the results including got by using the emerging and enabling new technologies and new methods and solutions (including for example distributed propulsion system, unconventional forms, morphing, biomimics, etc.), demonstrates the possible implementation of the new development philosophy, new approach to aircraft conceptual design.

In this paper, an in-wheel vibration absorber for In-wheel-motor electric vehicle (IWM EV) is designed, and a comprehensive control strategy of in-wheel absorber and vehicle suspension is proposed to improve vehicle ride comfort. The proposed in-wheel vibration absorber, designed for suppressing the motor vibration, is composed of a spring and a controllable damper. The values of in-wheel spring stiffness and damper initial coefficient are determined by using the improved particle swarm optimization (IPSO) algorithm, which is carried on the typical driving condition. To deal with the negative interaction effects between vehicle suspension and in-wheel absorber, the linear quadratic regulator (LQR) algorithm is utilized to control suspension damper, and the fuzzy PID method is utilized to control in-wheel damper. Based on the four evaluation indexes including vehicle body vertical acceleration, suspension dynamic deflection, wheel dynamic load and motor wallop, the simulation results show that, the proposed LQR control of suspension effectively improves vehicle ride comfort, and the fuzzy PID control of in-wheel damper exhibits superior performance of motor vibration suppressing in comparison to conventional electric wheel.

This paper presents a new methodology to evaluate the performance of an electric vehicle hybrid power system consisting of a fuel cell and a supercapacitor. The study compares the results with those obtained for a battery-electric vehicle. The methodology extends to three driving modes, ECO, NORMAL, and SPORT, corresponding to conservative, moderate, and aggressive acceleration, and three driving conditions, low, medium, and high energy demand. We develop a simulation process to evaluate the energy consumption and the energy rate of a specific electric vehicle used as a prototype for the study. The methodology applies to a driving route that includes acceleration, deceleration, braking, and constant speed segments reproducing standard driving conditions in urban journeys. The proposed method considers combined driving modes, ECO, NORMAL, and SPORT, in each acceleration process, with variable fractions, 0% to 100%, for each mode. This methodology optimizes the simulation results as it fits the current driving way in urban environments. The simulation results show an average reduction in energy consumption of 37% and 27.1% in vehicle weight, contributing to lower energy use. The study concludes that using a hybrid power system, fuel cell/supercapacitor, instead of a battery in electric vehicles is beneficial, especially in journeys with frequent acceleration processes.

Electric vehicles can effectively make use of the time-of-use electricity price to reduce the charging cost, meanwhile using the grid power to preheat the battery before departure is particularly important for improving the vehicle mileage and reducing the use cost.In this paper, a dynamic programming algorithm is used to optimize the battery AC charging-preheating strategy to minimize the total cost of battery charging and preheating, with the charging current and battery preheating power consumption as the control variables. The cost difference between the optimized control strategy and the conventional preheating strategy was analyzed under different ambient temperatures (-20℃~ 0℃) and different target travel time (7:00 ~ 12:00). The simulation results show that the optimized control strategy makes the battery SOC and temperature reach the set value at the user's target departure time, and the total cost of the grid is the lowest. Compared with the conventional preheating strategy, the optimized control strategy can utilize the power grid energy in the valley price area, reduce the opening time of water heating PTC in the flat and the peak price zones, and the cost utilization rate can reach 18.41% ~ 73.96%, and the cost-saving effect is significant.

In this study, we focused on the eco-driving of electric vehicles (EVs). The target vehicle is an electric bus developed by our research team. Using the parameters of the bus and speed pattern optimization algorithm, we derived the EV eco-driving speed pattern. Compared to eco-driving of internal combustion engine vehicles (ICVs), we found several different characteristics. We verified these characteristics with actual vehicle driving test data of the target bus, and the results confirmed its rationality. The EV eco-driving method can improve electricity consumption by about 10% - 20% under the same average speed.

Electric vehicles (EV) are getting more commonplace in the transportation sector in recent times. As the present trend suggests, this mode of transport is likely to replace the internal combustion engine (ICE) vehicles in near future. Each of the main EV components has a number of technologies that are currently in use or can become prominent in the future. EVs can cause significant impacts on the environment, power system, and other related sectors. The present power system can face huge instabilities with enough EV penetration; but with proper management and coordination, EVs can be turned into a major contributor to the successful implementation of smart grid. There are possibilities of immense environmental benefits as well, as the EVs can extensively reduce the greenhouse gas emission from the transportation sector. However, there are some major obstacles for EVs to overcome before replacing the ICE vehicles totally. This paper is focused on reviewing all the useful data available on EV configurations, energy sources, motors, charging techniques, optimization techniques, impacts, trends, and possible directions of future developments. Its objective is to provide an overall picture of the current EV technology and ways of future development to assist in future researches in this sector.

With the development of higher voltage power grid, the high and low voltage parallel loops are emerging, which lead to energy losses, even threaten the security and stability of power system. The multi-infeed HVDC configurations widely appearing in AC/DC interconnected power system make this situation even worse. Aimed at energy saving and system security, a decision optimization method for power grid operating condition with high and low voltage parallel loops is proposed in this paper. Firstly, considering hub substation distribution and power grid structure, parallel loop opening schemes are generated with GN algorithm. Then, candidate opening schemes are preliminarily selected from all these generated schemes based on a filtering index. Finally, with the influence on power system security, stability and operation economy in consideration, an evaluation model for candidate opening schemes is founded based on analytic hierarchy process (AHP). And a fuzzy evaluation algorithm is used to find the optimal scheme. Simulation results of New England 39-bus system and an actual power system validate the effectiveness and superiority of this proposed method.

Battery electric vehicles provide an opportunity to balance supply and demand in future power systems with high shares of fluctuating renewable energy. Compared to other storage systems such as pumped-storage hydroelectricity, electric vehicle energy demand is highly dependent on charging and connection choices of vehicle users. We present a model framework of a utility-based stock and flow model, a utility-based microsimulation of charging decisions, and an energy system model including respective interfaces to assess how the representation of battery electric vehicle charging affects energy system optimization results. We then apply the framework to a scenario study for controlled charging of nine million electric vehicles in Germany in 2030. Assuming a respective fleet power demand of 27 TWh, we analyze the difference between power-system-based and vehicle user-based charging decisions in two respective scenarios. Our results show that taking into account vehicle users’ charging and connection decisions significantly decreases the load shifting potential of controlled charging. The analysis of marginal values of equations and variables of the optimization problem yields valuable insights on the importance of specific constraints and optimization variables. In particular, state-of-charge assumptions and representing fast charging drive curtailment of renewable energy feed-in and required gas power plant flexibility. A detailed representation of fleet charge connection is less important. Peak load can be significantly reduced by 5% and 3% in both scenarios, respectively. Shifted load is very robust across sensitivity analyses while other model results such as curtailment are more sensitive to factors such as underlying data years. Analyzing the importance of increased BEV fleet battery availability for power systems with different weather and electricity demand characteristics should be further scrutinized.

The utilization of fuel cells (FC) in automotive technology has experienced significant growth in recent years. Fuel cell hybrid electric vehicles (FCHEVs) are powered by a combination of fuel cells, batteries, or/and ultracapacitors (UCs). By integrating power converters with these power sources, the FCHEV system can overcome the limitations of using them separately. The performance of an FCHEV is influenced by the efficiency of the power electronics converter controller, as well as the technical efficiency of the power sources. FCHEVs need intricate energy management systems (EMSs) to function effectively. Poor EMS can lead to low efficiency and accelerated fuel cell and battery degradation. The literature discussed various types of EMSs, such as equivalent consumption minimization strategy, classical PI controller, fuzzy logic controller, and Mutative Fuzzy Logic Controller (MFLC). However, comparing different EMSs can be challenging due to the varying vehicle and system parameters, which might lead to false claims being made regarding system performance. This research aims to categorize and discuss the various topologies of FCHEVs, highlighting their pros and cons, and comparing several EMSs based on performance metrics such as State of Charge (SOC) and FC deterioration.

This study evaluates eight-year ownership costs for battery electric vehicles (BEV) versus non-plugin hybrid vehicles using forecasting to estimate future electricity and conventional gasoline prices and incorporating these in a multiple design of experiments simulation. Results suggest that while electric vehicles are statistically dominant in terms of variable costs over an 8-year life-span, high-performance hybrid non-plugins achieve variable fuel costs nearly as good as low-performing electric vehicles (those attaining only 3 miles per kilowatt hour) and that these hybrid acquisition costs are (on average) lower yet the vehicles retain higher residual values. In general, the six smallest ownership costs are split evenly between hybrid and electric vehicles; however, inflation for conventional regular gasoline is estimated to outstrip inflation per kilowatt hour. Thus, non-plugin hybrid cars are likely to require considerably more advanced engineering to keep pace.

Energy efficiency and leakage magnetic field (LMF) are two important issues in electric vehicle inductive chargers. In this work, the maximum achievable coil efficiency and the corresponding LMF strength are formulated as functions of hardware parameters, and figure of merits (FOM) are proposed for assessing the efficiency and LMF performance of the coil assembly pair. The impacts of the coil assemblies’ geometric parameters on both FOMs are examined with the aid of finite element analysis (FEA), and measures to improve the FOMs are extracted from FEA results. A coil assembly pair is manually optimized within given dimensional limits. Compared with the initial design, the optimized one achieves higher efficiency and lower LMF strength while consuming less copper. The performance improvement is verified by FEA results and experimental data measured on an 85 kHz electric vehicle inductive charger prototype. The key measures for coil assembly optimization are summarized.

The diffusion of electric vehicles (EVs) can be sustained by the presence of integrated solutions offering parking and clean power supply. The recourse to DC systems allows to better integrate EV bidirectional energy exchange, photovoltaic panels and energy storage. In this paper, a methodology for optimal techno-economic sizing of a DC-microgrid for covering EV mobility needs is carried out. It is based on the definition of different scenarios of operation, according to typical EV usage outlooks and environmental conditions. In each scenario, optimal operation is carried out by means of a specific approach for EV commitment on different stations. The sizing procedure is able to handle the modular structure of microgrid devices. The proposed approach is applied to a case study of envisaged EV service fleet for Bari port authority.

This paper describes a case study for applying of hybrid-electric propulsion system for a general aviation aircraft. The work was performed by a joint team of CIRA and the Department of Industrial Engineering of the University of Naples “Federico II”. Electric and hybrid electric propulsion for aircraft has gained widespread and significant attention over the past decade. The driver for industry interest has principally been the need to reduce emissions of combustion engine exhaust products and noise, but increasingly studies revealed potential for overall improvement in energy efficiency and mission flexibility of new aircraft types. The project goal was to demonstrate feasibility of aeronautic parallel hybrid-electric propulsion for a Light aircraft varying the mission profiles and the electric configuration. Through a creation, and application, of a global model, with software AMESim^®, in which it can be represented everything about the components chosen by the industrial partners, some interesting considerations are carried out. In particular, it was confirmed that with the only integration of state of the art technologies, for some particular missions, the advantages of aircraft hybrid-electric propulsion, for light aircraft, are notable.

The cities of the future are places of sustainable mobility and a continuous reduction in the amount of harmful substances entering the surrounding environment. Current emission models are mainly dedicated to fully combustion vehicles and do not fully reflect the actual emissions of vehicles in the fleet, which is becoming increasingly diverse. The increasing share of hybrid and electric vehicles is generating the need to measure emissions and energy consumption from these vehicles and to develop new emission models that are accurate. This problem mainly concerns low-emission zones in cities, where mobility planning should be based on simulation models that are based on a continuously updated database. This work concerns the proposal of a two-dimensional model of emissions from hybrid vehicles using artificial neural networks for low-emission zones. The results can be used to further develop such emission models.

This work presents the design, construction and performance evaluation of a photovoltaic greenhouse as an energy hub (EH) in modern agriculture that integrates battery energy storage (BES) and an electric vehicle charging station (EV). The greenhouse is composed of 48 semi-transparent PV panels with nominal transparency of 20% and 110 W capacity. The control of the PV greenhouse as EH was approached as an optimization problem with the aim of minimizing the cost of the energy used from the grid. Simulation results indicate that the integrated BES is capable of balancing power transactions within the microgrid. In addition, it was found that the case of slow charging of the EV at night was less demanding on the BES than fast charging during the day in terms of abrupt power transitions and average depletion of BES SOC (61% vs 53%). Empirical results also demonstrated the negative impact of dust generated by agricultural activity on the performance of solar panels. For a period analyzed of three years, an average yearly production loss of 6.8% was calculated.

This work aims to study and analyze a hybrid power system for electric vehicles consisting of a dual low and high-rate lithium battery block and a fuel cell. In this configuration, the high-rate lithium battery powers the electric vehicle in high power demand processes like acceleration mode or on an uphill road; the low-rate battery operates at a low output power range, servicing the auxiliary systems and low power loads and the fuel cell supplies energy at intermediate power demand conditions, normal driving mode, constant velocity, or flat and downhill terrain. The dual power system improves global efficiency since every power unit operates optimally depending on driving conditions. Power sharing optimizes the lithium battery performance and fuel cell capacity, minimizing the size and weight of each energy system and enlarging the driving range. A comparative study between different lithium battery configurations and fuel cell shows an efficiency improvement of 31.4% for the hybrid dual battery block and fuel cell operating in low, high, and intermediate output power ranges, respectively. The study bases on a simulation process recreating current driving conditions for electric cars in urban, peripheral, and intercity routes. An alternative solution consisting of a hybrid system, fuel cell and a high rate lithium battery produces a 29 % power gain.

This paper presents an Application Based Active Learning (ABAL) methodology on Power Electronics (PE) and Electric Machines (EM) as a hybrid laboratory course for the undergraduate students to design and implement the real-world engineering problems. The ABAL is a type of active learning which is a branch of Learner-centered teaching (LCT). The DC/DC converter along with the speed control of DC separately excites the motor. In addition, a DC/AC converter is designed to control the speed of an induction motor. The results are then investigated on a hardware platform under the ABAL experimental methodology. This paper also discusses the problem identification selection of the equipment, circuit design, hardware mounting and critical analysis of the results acquired from the hybrid laboratory. The ABAL methodology was evaluated based on student satisfaction, feedback, grades and interest to solve the real-world problem rather than cramming the engineering concepts and fulfill so-called lab routine and tasks

Background: With the trend of intelligent display, the interface design of in-vehicle HUD is an expanding research field; Methods: To solve the subjectivity and uncertainty in the optimization of HUD interface design schemes, this paper proposed a hybrid scheme evaluation and optimization method based on entropy weight and VIKOR. The entropy weight method was used to reduce the subjectivity the decision-maker's weighting and obtain the objective weight of each indicator; The VIKOR method was used to obtain the best ranking of alternative schemes, and then the optimal interface design scheme was selected; Results: The evaluation of in-vehicle HUD interface design schemes were taken as an example for verification and calculation. The results showed that this method considers the subjectivity and uncertainty of the decision-making process in the optimization of design scheme, which can effectively improve the objectivity and accuracy of the evaluation results, and provide a reference for designers to optimize interface design schemes.

The development of electric aircrafts is becoming an important technology for achieving the goals set by the European Commission for the reduction of gases emissions by 2050 in the aeronautical transportation system. However, there is a gap between the values of specific power in commercial electric machines and the ones required for aeronautical applications. Therefore, the search for alternative materials and non-conventional designs is mandatory. One emergent solution is using superconducting machines and systems to overcome the current limits of conventional electrical machines. This work reviews the new hybrid and all-electric aircraft tendencies, complementing it with recent research on the design and development of high specific power superconducting machines. This includes the main topologies for hybrid and all-electric aircraft, with an overview of the ongoing worldwide projects of these types of aircrafts, systematizing the main characteristics of their propulsion systems. It also includes the research on superconducting machines for the purpose of high specific power, considering the impact on the redesign of aircraft systems in the electrical, cooling, and fuel source sense.

Electro-mechanical braking(EMB) which represents development direction of autonomous and intelligent braking plays very useful role on enhancing the braking response performance and intelligence level for mine underground electric trackless rubber-tired vehicle (ETRV). However,there is no Electro-Mechanical Brake system applied practically in coal mine UTRV until now.The accurate control of braking clamping force can determine the length and precision of braking distance of mine ETRV.In addition,because of poor working conditions in underground coal mine tunnel ,braking clamping force sensor may be easy to occur failure,which may cause vital accident.Therefore,A cascaded three-closed-loop EMB system with a positive clamping force sensor or force estimator built for ETRV is established to achieve autonomous elimination and reset of braking clearance and reliable braking force tracking ability via utilizing the electro motor rotor angle displacement and hysteresis effect of mechanical components in this EMB.The results of simulation and experiment indicate that clamping force response is faster than traditional hydraulic disk braking system and proposed force estimator presents good fault-tolerant ability when sensor is fault.This EMB can replace the current hydraulic brake system to enhance automation level of braking control for ETRVs and braking force response performance, reduce oil pollution and cost of maintenance, which is also key technology support for really precise motion control of mine autonomous driving vehicles.

This study conducts a comprehensive review of the integration of Hybrid Electric Turbochargers in mass-produced road vehicles. The primary objective is to inform the readers about the potential advantages and innovative applications of HETs. Employing a SWOT analysis, the research compares the performance of HETs on thermal engines versus traditional turbochargers and HETs on thermal engines versus HETs on hybrid engines based on a synthesis of multiple research findings. The study elucidates the fundamental mechanics of turbochargers, emphasizing their inherent benefits. Additionally, it introduces a novel approach with the integration of the hy-brid-electric turbocharger, demonstrating its capacity, supported by practical examples. The in-corporation of turbochargers with energy recovery mechanisms, including HETs, is shown to significantly contribute to emissions reduction. Moreover, the electric drive facilitates the utili-zation of hybrid turbines, particularly on low-displacement engines, resulting in enhanced effi-ciency, torque, and liter power. In conclusion, the research underscores the potential of HETs to substantially mitigate the environmental impact of the transportation sector by reducing emis-sions and conserving energy. Their ability to optimize the fuel efficiency and power output of internal combustion engines, coupled with the feasibility of downsized engines, positions HETs as an attractive option for both manufacturers and consumers. However, it is acknowledged that the implementation of HETs is in its early stages, necessitating further research to comprehensively understand their environmental impact. Despite this, the promising positive impact on the en-vironment designates HETs as a technology deserving close attention in the forthcoming years.

In order to overcome the limitation of the traditional adaptive Unscented Kalman Filtering (UKF) algorithm in noise covariance estimation for statement and measurement, we propose a hybrid adaptive UKF algorithm based on combining Maximum a posteriori (MAP) criterion and Maximum likelihood (ML) criterion, in this paper. First, to prevent the actual noise covariance deviating from the true value which can lead to the state estimation error and arouse the filtering divergence, a real-time covariance matrices estimation algorithm based on hybrid MAP and ML is proposed for obtaining the statement and measurement noises covariance, respectively; and then, a balance equation the two kinds of covariance matrix is structured in this proposed to minimize the statement estimation error. Compared with the UFK based MAP and based ML, the proposed algorithm provides better convergence and stability.

There are many uncertainties and risks in residential electricity consumption during the economic development. Knowledge of the relationship between residential electricity consumption and its key determinant—income—are important to the sustainable development of electric power industry. Using panel data from 30 provinces for the 1995-2012 period, this study investigates how residential electricity consumption changes as incomes increase in China. Previous studies typically used linear or quadratic double-logarithmic models imposing ex ante restrictions on the indistinct relationship between residential electricity consumption and income. Contrary to those models, we employed a reduced piecewise linear model that is self-adaptive and highly flexible and circumvents the problem of “prior restrictions.” Robust tests of different segment specifications and regression methods are performed to ensure the conservatism of the research. The results provide strong evidence that the income elasticity was approximately one, and it remained stable throughout the estimation period. The income threshold at which residential electricity consumption automatically remains stable or slows has not been reached. To ensure the sustainable development of the electric power industry, introducing higher energy efficiency standards for electrical appliances and improving income levels are vital. And government should emphasize electricity conservation in industrial sector rather than in residential sector.

The state detection of power cable is very important to ensure the reliability of power supply. Traditional sensors are mostly based on electric field detection, the operation is complex, and its efficiency needs to be improved. This paper optimizes the design and development of the magnetic field detection sensor for AC power cables. Firstly, through the establishment of the magnetic field sensor model, it is determined that permalloy is the material of the magnetic core, the optimal aspect ratio of the magnetic core is 20, and the ratio of coil length to core length is 0.3. Secondly, the coil simulation model is established, and it is determined that the optimal number of turns of the coil is 11000 turns, the diameter of the enamelled copper wire is 0.08mm, and the equivalent magnetic field noise of the sensor is 0.06pT. Finally, the amplifying circuit based on negative magnetic flux feedback is designed and the sensor is assembled, and the experimental circuit is built for sensitivity test. the results show that the sensitivity of the magnetic field sensor is 327.6mV/μT. The sensor designed in this paper has the advantages of small size, high sensitivity, easy to carry and high reliability.

In order to improve contrast and restore color for underwater image captured by camera sensors without suffering from insufficient details and color cast, a fusion algorithm for image enhancement in different color spaces based on contrast limited adaptive histogram equalization (CLAHE) is proposed in this article. The original color image is first converted from RGB color space to two different special color spaces: YIQ and HSI. The color space conversion from RGB to YIQ is a linear transformation, while the RGB to HSI conversion is nonlinear. Then, the algorithm separately operates CLAHE in YIQ and HSI color spaces to obtain two different enhancement images. The luminance component (Y) in the YIQ color space and the intensity component (I) in the HSI color space are enhanced with CLAHE algorithm. The CLAHE has two key parameters: Block Size and Clip Limit, which mainly control the quality of CLAHE enhancement image. After that, the YIQ and HSI enhancement images are respectively converted backward to RGB color. When the three components of red, green, and blue are not coherent in the YIQ-RGB or HSI-RGB images, the three components will have to be harmonized with the CLAHE algorithm in RGB space. Finally, with 4 direction Sobel edge detector in the bounded general logarithm ratio operation, a self-adaptive weight selection nonlinear image enhancement is carried out to fuse YIQ-RGB and HSI-RGB images together to achieve the final fused image. The enhancement fusion algorithm has two key factors: average of Sobel edge detector and fusion coefficient, and these two factors determine the effects of enhancement fusion algorithm. A series of evaluate metrics such as mean, contrast, entropy, colorfulness metric (CM), mean square error (MSE) and peak signal to noise ratio (PSNR) are used to assess the proposed enhancement algorithm. The experiments results showed that the proposed algorithm provides more detail enhancement and higher values of colorfulness restoration as compared to other existing image enhancement algorithms. The proposed algorithm can suppress effectively noise interference, improve the image quality for underwater image availably.

A new type of artificial block is proposed by modifying the traditional block. Based on the physical model experiment, the wave reflection and run-up characteristics of the new ecological blocks under regular waves were examined, and the influence of the height of the "planting trough" border on the hydrodynamic properties was analyzed. The results indicate that the wave reflection and run-up would decrease with a decrease in the breakwater slope. As wave height increases, wave run-up increases, and the reflection coefficient falls. Wave reflection and run-up increase with an increasing wave period. The relative depth of the water has a smaller impact on the wave reflection than the wave run-up. The reflection coefficient of the new ecological blocks is consistently lower than that of the conventional and continues to decrease as the border of the "planting trough" is raised. The raised borders prevent water loss in the trough, resulting in no significant improvement in the wave run-up performance of the new blocks. The reflection coefficient and the relative run-up R/H gradually increase with the average wave breaking parameter ξ increase. The crude permeability coefficients for the new blocks, New Heights 1 and New Heights 2, are 0.53, 0.53, and 0.54, respectively.

Air conditioning system of electric vehicles has new change as the internal combustion engine is being replaced with electrified AC motor. With large amount of batteries installed at the bottom of frame, the conventional compressor which is belt-driven can be removed and another AC motor can play the role for air conditioning in electric vehicles. From this change, the system efficiency would be improved since it is possible to control the electrified compressor independently from traction system in contrast with the belt-driven compressor. As a result, by applying the electrified compressor for air conditioning system, the whole system can achieve better efficiency and longer driving distance, which is most important in electric vehicles. In this paper, 3-phase interior permanent magnet synchronous motor (IPMSM) was designed using lumped-parameter model and finite element method.

The purpose of this work is to present an adaptive sliding mode luenberger state observer with improved disturbance rejection capability and better tracking performance under dynamic conditions. The sliding hyperplane is altered by incorporating the estimated disturbance torque with the stator currents. Also, the effects of parameter detuning on the speed convergence is observed and compared with the conventional disturbance rejection mechanism. The entire drive system is first built in simulink environment. Then, the simulink model is integrated with RT-Lab blocksets and implemented in a relatively new real-time environment using OP4500 real-time simulator. Real-time simulation and testing platforms have succeeded offline simulation and testing tools due to their reduced development time. The real-time results validate the improvement in the proposed state observer and also correspond to the performance of the actual physical model.

This paper presents an optimized energy management strategy for Li-ion power batteries used on electric vehicles (EVs) at low temperatures. Under low-temperature environments, EVs suffer a sharp driving range loss resulted from the energy and power capability reduction of the battery. Simultaneously, because of Li plating, battery degradation becomes an increasing concern as temperature drops. All these factors could greatly increase the total vehicle operation cost. Prior to battery charging and vehicle operating, preheating battery to a battery-friendly temperature is an approach to promote energy utilization and reduce total cost. Based on the proposed LiFePO4 battery model, the total vehicle operation cost under certain driving cycles is quantified in the present paper. Then given a certain ambient temperature, a target temperature of preheating is optimized under the principle of minimizing total cost. As for the preheating method, a liquid heating system is also implemented on an electric bus. Simulation results show that the preheating process becomes increasingly necessary with a decreasing ambient temperature; however, the preheating demand declines as driving range grows. Vehicle tests verify that the preheating management strategy proposed in this paper is able to save total vehicle operation cost.

Optimizing the NACA0015 airfoil which is widely applied in small-scale vertical axis wind turbine to make it has a better aerodynamic performance. In the optimization process, using CST parameterization method to perturb the airfoil geometry, the thickness and camber of the airfoil are selected as the constraint, and the value of the maximum tangential force coefficient is chosen as the objective function, the genetic algorithm based on non-dominated sorting (NSGA-II)is selected as an optimization method, calculates the aerodynamic performance of the airfoil by applying the approach of combining XFOIL program and Viterna-Corrigan post-stall mode ,and establishes the optimizing process by the optimization software modefrontier for NACA0015 airfoil’s muti-point optimization, validate the airfoil’s performance with CFD finally. The result illustrates that, by comparing with the NACA0015 airfoil, the optimized airfoil’s lift to drag ratio is improved over a wide range of attack angles, the stall performance is more gentle. The maximum lift coefficient, the maximum lift-drag ratio and the maximum tangential force coefficient are increased by 7.5%,9 and 8.87%, respectively. The optimized airfoil has a wide variable condition performance, more suitable for the operating conditions of a vertical axis wind turbine. Finally, predict the rotor efficiency with optimized airfoil and NACA0015 airfoil for different tip speed ratios and different solidities with multiple streamtube model, the result shows the rotor with optimized airfoil has a higher efficiency.

Single-phase-to-ground fault in non-effectively grounded systems poses serious public safety concern. Along with increasing deployment of low-voltage (LV) sensors, new opportunities and ways are created for solving this traditional problem in distribution systems. A new approach, identifying primary single-phase-to-ground line fault and locating it through measurement data from smart sensors deployed in the secondary side of distribution transformers, is proposed in this paper. When a fault occurs in primary distribution feeder, the transient aerial mode voltage (AMV) of each LV smart sensor is calculated. The fault line can be identified by an abrupt change value of AMV at LV side. Next, by finding the position of the maximum value of this AMV from LV sensors on the fault line, the fault location can be pinpointed to two neighboring distribution transformers. The proposed method has been proven to be efficient and reliable by simulation studies.

This study uses a wind turbine case study to showcase an architecture for implementing a distributed digital twin in which all important aspects of a predictive maintenance solution in a DT use a fog computing paradigm, and the typical predictive maintenance DT is improved to offer better asset utilization and management through real time condition monitoring, predictive analytics, and health management of selected components of Wind turbines in a wind farm.. Digital twin (DT) is a technology that sits at the intersection of Internet of Things, Cloud Computing and Software Engineering to provide a suitable tool for replicating physical objects in the digital space. This can facilitate the implementation of asset management in manufacturing systems through predictive maintenance solutions leveraged by Machine Learning (ML). With DTs, a solution architecture can easily use data and software to implement asset management solutions such as Condition Monitoring and Predictive Maintenance using acquired sensor data from physical objects and computing capabilities in the digital space. While DT offers a good solution, it is an emerging technology that could be improved with better standards, architectural framework, and implementation methodologies. Researchers in both academia and industry have showcased DT implementations with different levels of success. However, DTs remain limited in standards and architectures that offer efficient predictive maintenance solutions with real time sensor data, and intelligent DT capabilities. An appropriate feedback mechanism is also needed to improve asset management operations.

The development of technology that combines supercapacitors and lithium-ion batteries by externally connecting them in parallel is ongoing. This study examines the correlation between the volume ratio and electrical characteristics of a cell made by internally connecting a battery capacitor with Li4Ti5O12 as the anode active material and a supercapacitor in parallel. It was found that increasing the volume occupied by the battery capacitor in the cell led to increased cell energy and resistance, resulting in decreased output characteristics. Conversely, increasing the volume occupied by the supercapacitor in the cell led to a decrease in the IR drop during discharge and cell temperature when evaluating cycle characteristics with a current of 20C. The study also examined the behavior of the current distributed during the charging and discharging process based on the volume ratio of the supercapacitor and the battery capacitor. Analyzing the correlation between the volume ratio and electrical characteristics of supercapacitors and battery capacitors could potentially lead to the development of a new type of energy storage device.

Electric vehicles (EVs) will have a greater need for the amount of electricity needed to charge them as their popularity grows. It is anticipated that in order to accomplish this objective, it will be essential to implement a variety of solutions for grid transportation that are designed to complement one another and to make significant changes to the transmission infrastructure. It is possible to reduce the amount of energy that is lost on the power network through strategic planning and control, which may include economic models and methods to engage and reward users. This would eliminate the need for grid upgrades. Charging electric vehicles can also assist alleviate problems with transmission systems that are caused by the allocation of electric vehicles (EVs) using bidirectional charging method. The most significant problems that can occur with a transmission network are power loss and unstable voltage. Adding EV units to the transmission network is typically an effective method for resolving these challenges. As a result, EVs need to have the appropriate arrangement and dimensions. This research establishes where and how many electric vehicles (EVs) should be in a radial transmission network both before and after the adjustment is made. An artificially intelligent (AI) approach, known as a hybrid genetic algorithm particle swarm optimization (HGAIPSO), is used both before and after the radial network modification to find the optimal EV location and size. When electric vehicles are coordinated in an active transmission network, power losses are decreased, voltage profiles are raised, and system stability is increased. These benefits can be attributed to the greater use of electric vehicles. The simulation found that incorporating EVs into the testing system resulted in a considerable decrease in the quantity of power that was wasted. The minimal bus voltage of the system also undergoes similar kinds of enhancements. According to the findings of the comparative study, the proposed method mitigates both the voltage fluctuations and the power losses that occur in the transmission system. For type 1, type 2, and type 3 EV allocations, the IEEE-30 bus test system reduced real power loss by 40.70%, 36.24%, and 42.94%, respectively. IEEE-30 bus voltage reaches 1.01 pu.

The problems of operating range and costs are the two most critical bottlenecks restricting the extensive application of electric vehicles at home and abroad. There are also some prominent problems in China's electric vehicles, such as slow improvement of electric vehicle's operating range, difficulty in charging, slow charging, low utilization efficiency of charging resources, and high battery cost for electric vehicles, which lead to poor competitiveness of electric vehicles compared with traditional internal combustion engine (I.C.E.) vehicles. This paper analyzes the key factors restricting the development and popularization of electric vehicles in China from the aspects of strategic policy, sales situation and self problems. Through summarizing the experience and lessons of French standardization development strategy and electric vehicle development mode, this paper puts forward the hypothesis leading the development of electric vehicles through standardization to enhance their competitiveness, gives the specific suggestions, and briefly analyzes the feasibility from the aspects of product situation. The research content of this paper provides a certain basis and ideas for the future research work.

Vehicle driveability is one of the important vehicle attributes in range-extender electric vehicles due to the electric motor torque characteristics at low-speed events. The process of validating and rectifying vehicle driveability attributes is typically utilised by a physical vehicle prototype that can be expensive and required several design iterations. In this paper, a model-based energy method to assess vehicle driveability is presented based on a high-fidelity 49 degree-of-freedom powertrain and vehicle systems. Multibody dynamics components were built according to their true centre of gravity relative to the vehicle datum for providing an accurate system interaction. The work covered a frequency at less than 20 Hz. The results that consisted of the component frequency domination are structured and examined to identify the low-frequency sensitivity based on different operating parameters such as a road surface coefficient. An energy path technique was also implemented on the dominant component by decoupling its compliances to study the effect on the vehicle driveability and low-frequency response. The outcomes of the research provided a good understanding of the interaction across the sub-systems levels. The powertrain rubber mounts were the dominant components that controlled the low-frequency contents (< 15.33 Hz) and can change the vehicle driveability quality.

The performance of the absolute atom gravimeters used on moving platforms, such as vehicles, ships and aircrafts, is strongly affected by the vibration noise. To suppress its influence, we summarize a vibration compensation method utilizing data measured by a classical accelerometer. The measurements with the accelerometer show that the vibration noise in the vehicle can be 2 order of magnitude greater than that in the lab during daytime, and can induce an interferometric phase fluctuation with a standard deviation of 16.70π. With the compensation method, our vehicle-mounted atom gravimeter can work normally in these harsh conditions. Comparing the Allan standard deviations before and after the vibration noise correction, we find a suppression factor of 22.74 can be achieved in static condition with an interrogation time of T = 20 ms, resulting a sensitivity of 1.35 mGal/Hz1/2, and a standard deviation of 0.5 mGal with an average time of 10 s. We also demonstrate the first test of an atom gravimeter in a moving vehicle, in which a suppression factor of 50.85 and a sensitivity of 60.88 mGal/Hz1/2 were realized with T = 5 ms.

This article explores the crucial task of estimating State of Charge (SOC) in Hybrid Electric Vehicles (HEVs) and examines the applicability of various regression models for this purpose. We delve into the strengths and limitations of Linear Regression, Support Vector Regression (SVR), and Neural Network Regression (NNR) in the context of SOC estimation. Linear regression provides a simple and interpretable baseline, SVR extends this to nonlinear relationships, while NNR emerges as a powerful tool with adaptive capabilities. The choice of model depends on factors such as data characteristics, interpretability, and computational resources. As the field evolves, the article advocates for a nuanced approach, possibly incorporating hybrid models, to achieve robust and accurate SOC estimation, contributing to the ongoing enhancement of HEV efficiency and sustainability.

Battery/Supercapacitor(SC) current tracking control is a key issue for hybrid energy storage system (HESS) in electric vehicles. An innovative passivity-based L2-gain adaptive control (PBL2AC) based on port-controlled Hamiltonian model with dissipativity (PCHD) for reference current tracking and bus voltage stability in HESS is presented. The developed PCHD model has considered both parameter variations and external disturbances. By using L2-gain disturbance attenuation, the PBL2AC ensures robust reference current tracking and stable bus voltage. Moreover, adaptive mechanism is adopted to estimate the electrical parameters. To validate the proposed control scheme for HESS, simulations and experiments were done and compared with traditional PID and sliding mode control under several typical driving cycles, and results show that the effectiveness of the proposed controller can be confirmed.

This paper expressed three regression models that predict the lithium-ion battery life for electric cars based on a supervised machine-learning regression algorithm. The Linear Regression, Bagging Regressor, and Random Forest Regressor models will be compared for capacity prediction of lithium-ion batteries based on voltage-dependent per-cell modeling. When sufficient test data is available, three linear regression learning algorithms will train this model to give a promising battery capacity prediction result. The effectiveness of the three linear regression models will be demonstrated experimentally. The experiment table system is built with an NVIDIA Jetson Nano 4GB Developer Kit B01, a battery, an Arduino, and a voltage sensor. The Random Forest Regressor model has evaluated the model's accuracy based on the average of the square of the difference between the initial value and the predicted value in the data set (MSE (Mean Square Error)), and RMSE (Root Mean Squared Error) is smaller than the Linear Regression model, Bagging Regressor model (MSE is 516.332762; RMSE is= 22.722957). The Linear Regression model with MSE and RMSE is the biggest (MSE is 22060.500669; RMSE is= 148.527777). This result allows the Random Forest Regressor model to remain a helpful life prediction of lithium-ion batteries. Moreover, this result allows rapid identification of battery manufacturing processes and will enable users to decide to replace defective batteries when deterioration in battery performance and lifespan are identified.

Existence of hybrid electric vehicles nowadays is one of the emerging technologies worldwide. Different countries are using this technology on their transportation, and nowadays, a lot of other countries are gradually adapting on using this kind of innovation in their transport system. Philippines is among these countries which aims to have a sustainable mobility by embracing the use of hybrid - electric vehicles but still lots of consumers are lacking awareness on this technology. Lack of information on the social, environmental, and economic potential benefits are among the main issues of Philippines consumers that really affect its uptake. The goal of this study was to evaluate the consumer’s perception and purchase intention on the transition of hybrid - electric vehicles for sustainable mobility and transportation here in the Philippines. It aimed to assess consumer awareness with hybrid - electric vehicles and its potential benefits to human beings in terms of social, environmental, and economic aspects. The study also gauged the impact of this perception on consumer’s purchase intention on hybrid - electric vehicles. These objectives were attained using the Descriptive Statistics and Correlation Analysis. Using these methods, the results revealed that majority of the consumers believed on the positive benefits of transitioning to hybrid - electric vehicles in terms of social, environmental, and economic aspects. This study also showed that these benefits have high impact on the consumer’s intention of buying or having a hybrid – electric vehicle. Electric vehicle is one of the most effective measure of decarbonizing the transport system. Furthermore, government and automotive businesses must strengthen their drive in spreading awareness of hybrid – electric vehicle’s benefits to consumers to further support country’s effort for development.

Natural polluted insulator surfaces are always coated with various kinds of soluble constituents, and those constituents affect flashover performance differentially. Currently this fact is not considered either in laboratory experiments or field pollution degree measurements, causing the existing insulation selection method to be deficient. In this paper a systematical research on insulator flashover voltage gradient correction involving types of soluble pollution constituents was presented. Taking typical type glass insulator as the sample, its flashover tests polluted by typical soluble chemicals NaCl, NaNO₃, KNO₃, NH₄NO₃, MgSO₄, Ca(NO₃)₂ and CaSO₄ were carried out. Then the flashover gradient correction was made combining the flashover performance of each soluble constituent, the ESDD contribution of the seven constituents, as well as the saturation performance of CaSO₄. The correction was well verified with the flashover test results of insulator polluted by three types of soluble mixture. Research results indicate that the flashover gradient correction method proposed by this paper performs well in reducing the calculating error. It is recommended to carry out component measurements and flashover gradient correction to better select outdoor insulation configuration.

Attribute reduction is a core technique in the rough set domain and an important step in data preprocessing. Researchers have proposed numerous innovative methods to enhance the capability of attribute reduction, such as the emergence of multi-granularity rough set models, which can effectively process distributed and multi-granularity data. However, these innovative methods still have many shortcomings, such as how to deal with complex constraints and how to perform multi-angle effectiveness evaluations. Based on the multi-granularity model, this study proposes a new method of attribute reduction, namely using multi-granularity neighborhood information gain ratio as the measurement criterion. This method combines both supervised and unsupervised perspectives, and by integrating multi-granularity technology with neighborhood rough set theory, constructs a model that can adapt to multi-level data features. This model can select the optimal granularity level or attribute set according to the requirements. Finally, the proposed method is experimented with on 15 UCI datasets against six other attribute reduction algorithms. The experimental outcomes, upon analysis and comparative review, substantiate the reliability and consistency of the attribute reduction approach introduced in this study.

Addressing the pressing challenge of global warming, reducing greenhouse gas emissions in the transportation sector is a critical imperative. Battery and fuel-cell electric vehicles have emerged as promising solutions for curbing emissions in this sector. In this study, we conducted a comprehensive life cycle assessment (LCA) for typical passenger vehicles, heavy duty trucks and city buses using either proton-exchange membrane fuel cells or Li-ion batteries with different cell chemistries. To ensure accuracy, we supplemented existing studies with data from the literature, particularly for the recycling phase, as database limitations were encountered. Our results highlight that fuel cell and battery systems exhibit large emissions in the production phase. Recycling can significantly offset some of these emissions, but a comparison of the technologies examined revealed considerable differences. Overall, battery electric vehicles consistently outperform fuel cell electric vehicles regarding absolute greenhouse gas emissions. Hence, we recommend prioritizing battery electric over fuel cell vehicles. However, deploying fuel cell electric vehicles could become attractive in a hydrogen economy scenario where other factors, e. g. the conversion and storage of surplus renewable electricity via electrolysis, become important.

This study probes the probabilistic features of major fire hazards in enclosed spaces to establish their importance to the occurrence of fires onboard ro-ro passenger ships and in turn to raise effective operational countermeasures. Distinct from the previous studies, the present research employs Bayesian Network (BN) analysis to determine the probabilities of fire hazards more effectively. The findings of the research include five critical basic events (BE) identified namely, vehicle engine fire (fuel system fault), vehicle electric fire (electrical equipment defect or short circuit), used car electrical fire, reefer units electrical fire (electrical appliances defects or short circuit), and cargo spontaneous combustion. Additionally, the risk of fire for lithium - ion battery powered vehicles is also highlighted in the process of BN analysis, which prompts the authors to propose preventive measures for mitigating the possibility of fire occurrence on this type of electric vehicles. It is hoped that these measures can be essential justifications for establishing relevant rules regarding carrying LIB vehicles in enclosed spaces on international level.

Gas and power networks are tightly coupled and interact with each other due to physically interconnected facilities. In an integrated gas and power network, a contingency observed in one system may cause iterative cascading failures, resulting in network wide disruptions. Therefore, understanding the impacts of the interactions in both systems is crucial for governments, system operators, regulators and operational planners, particularly, to ensure security of supply for the overall energy system. Although simulation has been widely used in the assessment of gas systems as well as power systems, there is a significant gap in simulation models that are able to address the coupling of both systems. In this paper, a simulation framework that models and simulates the gas and power network in an integrated manner is proposed. The framework consist of a transient model for the gas system and a steady state model for the power system based on AC-Optimal Power Flow. The gas and power system model are coupled through an interface which uses the coupling equations to establish the data exchange and coordination between the individual models. The bidirectional interlink between both systems considered in this studies are the fuel gas offtake of gas fired power plants for power generation and the power supply to LNG terminals and electric drivers installed in gas compressor stations and underground gas storage facilities. The simulation framework is implemented into an innovative simulation tool named SAInt (Scenario Analysis Interface for Energy Systems) and the capabilities of the tool are demonstrated by performing a contingency analysis for a real world example. Results indicate how a disruption triggered in one system propagates to the other system and affects the operation of critical facilities. In addition, the studies show the importance of using transient gas models for security of supply studies instead of successions of steady state models, where the time evolution of the line pack is not captured correctly.

This work presents a novel approach for the study of the movement of droplets on inclined surfaces under the influence of gravity and chemical heterogeneities. The developed numerical methodology uses data-driven modeling to extend the applicability limits of an analytically derived reduced-order model for the contact line velocity. More specifically, while the reduced-order model is able to capture the effects of the chemical heterogeneities to a satisfactory degree, it does not account for gravity. To alleviate this shortcoming, datasets generated from direct numerical simulations are used to train a data-driven model for the contact line velocity, which is based on the Fourier neural operator and corrects the reduced-order model predictions to match the reference solutions. This hybrid surrogate model, which comprises of both analytical and data-driven components, is then integrated in time to simulate the droplet movement, offering a speedup of five orders of magnitude compared to direct numerical simulations. The performance of this hybrid model is quantified and assessed in different wetting scenarios, by considering various inclination angles and values for the Bond number, demonstrating the accuracy of the predictions as long as the adopted parameters lie within the ranges considered in the training dataset.

In this paper, an adaptive proportional and integral (PI) controller for speed control of electric drives is developed. The adaptive PI controller is designed based on model reference adaptive identification and the Lyapunov function so that the system stability can be proved. To identify the inertia, the viscous friction torque coefficient, and the load torque simultaneously and smoothly, sinusoidal speed reference is usually employed. A modified motion equation considering the low-pass filter for feedback speed and the Coulomb friction torque is introduced and the relationship between the identified parameters and their actual values are clarified. A high-precision digital simulation model is built based on MATLAB/Simulink. The effectiveness of the proposed method is verified by simulations under various conditions.

Unmanned vehicles (UVs) have become increasingly important in various scenarios of civil and military operations. The present work aims at the conceptual design of a modular Amphibious Unmanned Ground Vehicle (A-UGV), that can be easily adapted for different types of land and/or water missions, with low monetary cost (&lt;5k€, without sensors). Basing the design on the needs highlighted in the 2021 review of the Strategic Directive of the Portuguese Navy, the necessary specifications and requirements are established for two mission scenarios. Then a market research analysis focused on vehicles currently available, and their technological advances, is conducted to identify existing UVs solutions and respective characteristics/capabilities of interest to the current work. To study and define the geometry of the hull and the configuration of the A-UGV itself, preliminary computational structural and fluid analyses are carried out to ensure it complies with the specifications initially established. As a result, one obtains a fully electric vehicle, with approximate dimensions of 1050×670×450mm (length-width-height), enabled with 6×6 traction capable of reaching 20km/h in land, possesses amphibious capabilities of independent propulsion in water up to 8kts, and with an estimated autonomy of over 60 minutes.

As the natural resources are getting exhausted, the concept of sustainable development of region has received increasing attentions, especially for resource-dependent cities. In this paper an innovative method that emergy analysis and IPAT (Human Impact Population Affluence Technology) model were combined in order to analyze the quantitative relationship of economic growth and energy consumption and further to evaluate its overall sustainability level. Taiyuan, a traditional, resource-dependent city in China, is selected as the case study region. The main results show that total emergy of Taiyuan increased from 9.023× 1023 sej in 2007 to 9.116× 1023sej in 2014, with 38% reduction on non-renewable emergy and 125% growth on imported emergy. Regional emergy money ratio (RMB) was reduced by 48% from 5.31× 1013sej/$ in 2007 to 2.74× 1013sej/$ in 2014, indicating that the increasing speed of consuming resources and energy was faster than the increase of GDP, and that Taiyuan’s money purchasing power declined. The lower emergy sustainability index (ESI) indicates that Taiyuan was explored and produced large quantities of mineral resources, which puts more stress on the environment as a consequence, and that this is not sustainable in the long run. The IPAT analysis demonstrates that Taiyuan sticks to the efforts of energy conservation and environmental protection, in order to promote regional sustainable development, it is necessary to take an integrated effort. Policy insights suggest that resourceful regions should improve include energy and resource efficiency, optimizing energy and resourceful structure.

The primary objective of this experiment is to enhance road safety and mitigate the occurrence of accidents by leveraging Low Power Wide Area Networks (LPWAN), specifically focusing on the Long Range (LoRa) network. Through comprehensive research into LPWANs and their various applications, we have designed and implemented a novel approach employing two mobile robots. These robots are utilized to emulate a typical traffic scenario, with one robot leading the way, skillfully maneuvering around obstacles, while the other robot closely follows behind, tracing the same path. The leading robot is tasked with collecting data from its internal environment, the external surroundings, and its operator through an array of sensors. Subsequently, this data is transmitted to the trailing robot. The follower robot's role is to analyze the data received and formulate decisions based on this information. Its objective is to mimic safe driving behavior, particularly when the received data deviates from the expected norms. In such instances, the follower robot will opt to decelerate significantly, thereby minimizing the risk of collision. By implementing this innovative system, we aim to significantly enhance driving safety and reduce the occurrence of accidents on the road.

In this paper, a novel permanent magnet-assisted synchronous reluctance machine (PMASynRM) with rare-earth PMs and ferrite magnets is proposed. The performance of PMASynRM is discussed with respected to the different magnet ratio of rare-earth PMs and ferrite magnets. Some characteristics including the flux density, output torque, cogging torque, output power, power factor, torque ripple, loss, efficiency, and demagnetization are calculated by 2-D finite element analysis (FEA). The analysis results show that the excellent performance can be obtained by using hybrid magnet of rare-earth PMs and ferrite magnets with the suitable magnet ratio, and provide some desirable cost-performance trade-off.

Graphene hybrid-filler polymer composites have emerged as prominent materials that revolutionize heavy industries. This study encapsulates the in-depth analysis of different influential factors such as filler/graphene type, aspect ratios, dispersion methods, filler-matrix compatibility, fiber orientation, synergistic effects, different processing techniques, and post-curing conditions that affect the processing, properties and determine the resultant applications of graphene hybrid polymer composites. Additionally, it discusses the substantial role of graphene collaboration with other fillers such as carbon nanotubes, silica, nano-clays and metal oxides to produce functionalized hybrid polymer composites with synergistically enhanced tailored properties to offer solutions for heavy industries like aerospace, automotive, electronics, and energy harvesting. The review concludes with some suggestions and outlook on the future of these composite materials by emphasizing the need for continued research to fully optimize their potential.

A low-cost bio-mass-derived carbon substrate has been employed to synthesize MoS₂@carbon composites through a hydrothermal method. Carbon fibers derived from natural cotton provide a three-dimensional and open framework for the uniform growth of MoS₂ nanosheets, thus constructing hierarchically coaxial architecture. The unique structure could synergistically benefit fast Li-ion and electron transport from the conductive carbon scaffold and porous MoS₂ nanostructures. As a result, the MoS₂@carbon composites, when served as anodes for Li-ion batteries, exhibit a high reversible specific capacity of 820 mAh g^-1, high-rate capability (457 mAh g^-1 at 2 A g^-1), and excellent cycling stability. The superior electrochemical performance makes the MoS₂@carbon composites to be low-cost and promising anode materials for Li-ion batteries.

The process involved in preparing driving simulator tests is a labor intensive one, and the nature of this complexity depends on the sophistication of the tests to be carried out, as well as the number of participants. Which has an impact on the duration of the research itself. The very solution of using driving simulators is a research tool that has been in use for many years and with great success. They are used in a very wide range of areas of human functioning. They replicate in a very realistic way the conditions that can occur in the external environment, offer the possibility of repetition of particular conditions and insight into certain behaviors that could be very difficult to initiate in real life. This article also describes the dis- ease of using simulators to conduct research activities, along with the workflow from assumptions to finalizing the research. An algorithm is also presented for the study of individual participants, with examples for separate research scenarios concerning driver behavior in the vicinity of pedestrian crossings.

Lily tepals have a short lifespan. Once the tepals senesce, the ornamental value of the flower is lost. Some cultivars have attractive purple ovaries and fruits which greatly enhance the ornamental value of Asiatic hybrid lilies. However, little is known about the molecular mechanisms of anthocyanin biosynthesis in Asiatic hybrid lily ovaries. To investigate the transcriptional network that governs purple ovary coloration in Asiatic hybrid lilies, we obtained transcriptome data from green ovaries (S1) and purple ovaries (S2) of Asiatic ‘Tiny Padhye’. Comparative transcriptome analysis revealed 4228 differentially expressed genes. Differential expression analysis revealed that nine unigenes including four CHS genes, one CHI gene, one F3H gene, one F3′H gene, one DFR gene, and one UFGT gene were significantly up-regulated in purple ovaries. One MYB gene, LhMYB12-Lat, was identified as a key transcription factor determining the distribution of anthocyanins in Asiatic hybrid lily ovaries. Further qPCR results showed unigenes related to anthocyanin biosynthesis were highly expressed in purple ovaries of Asiatic ‘Tiny Padhye’ at stages 2 and 3, while they showed an extremely low level of expression in ovaries of Asiatic ‘Yellow Pixels’ during all developmental stages. In addition, shading treatment significantly decreased pigment accumulation by suppressing the expression of several unigenes related to anthocyanin biosynthesis in ovaries of Asiatic ‘Tiny Padhye’. These results could further our understanding of the molecular mechanisms of anthocyanin biosynthesis in Asiatic hybrid lily ovaries.