Rice blast and brown planthopper (BPH) are two of the most destructive diseases and pests in rice (Oryza sativa L.) production in China. The development of multi-resistant varieties is widely recognized as the most efficient and environmentally friendly approach to controlling crop diseases and pests. Functional molecular markers (FMMs) have been developed from functional variants in the genic region associated with trait variation, greatly enhancing the efficiency of identifying and pyramiding valuable genes in crop breeding. In this study, two FMMs and a multiplex PCR amplification system were developed for two major broad-spectrum BPH resistance genes, Bph6 and Bph9. By assistance of FMMs in multi-resistant rice restorer line development pipeline, two lines (Huahui7713 and Huahui3006) with blast and BPH resistance were developed by pyramiding three resistance genes Pigm, Bph6 and Bph9. Huahui7713 and Huahui3006 as male lines, two new hybrid rice varieties (WeiLiangYou7713 and Xuanliangyou3006) were certificated and commercial released in China. WeiLiangYou7713 and Xuanliangyou3006 showed improved blast and BPH resistance, and no penalty on yield and grain-quality. Annual promotion area of WeiLiangYou7713 has exceeded 53.3 thousand hectares, indicating its widespread adoption and success in the market. Huahui7713 and Huahui3006 could have great potential for utilization in blast and BPH resistance rice breeding.

Background: Music evokes positive emotions and reduces stress and anxiety. Operating Room (OR) staff face various challenges which can lead to high levels of stress. The aim of the study is to assess whether listening to music during intraoperative phases improves the work environment by reducing anxiety and stress in the entire surgical team. Methods. A prospective observational study was conducted from February to September 2023, involving medical personnel, nursing staff, and nursing students. They were divided into two groups: Group 1 with music during surgical procedures, and Group 2 without music. Participants were administered two validated instruments: the Zung Anxiety Self-Assessment Scale (SAS) to measure anxiety, and the Positive and Negative Affect Schedule to assess emotions generating stress. Additional items were included for demographics, job satisfaction, and the organization method. Results. Music did not impact anxiety but increased positive emotions while reducing negative ones. Music had an ancillary effect, highlighting the need for significant organizational interventions aimed at increasing operator satisfaction, including voluntary rather than mandatory assignments for nursing staff. Conclusions. Music appears to reduce stress in the intraoperative team when supported by a positive work environment in which assigned operators have chosen to work in the OR.

(1) Background: Mixed Reality is a technology that has gained attention due to its unique capabilities for accessing and visualizing information, becoming a valuable tool for medicine, particularly for the operating room and surgical learning; (2) Methods: A systematic review was conducted following the PRISMA guidelines to answer the research questions established using the PICO framework; (3) Results: Although implementation of Mixed Reality applications in the operations room presents some challenges, when used appropriately, it can yield remarkable results. It can make learning easier, flatten the learning curve for several procedures, and facilitate various aspects of the surgical processes; (4) Conclusion: Technical complexity, equipment costs, and steep learning curves present significant obstacles to the widespread adoption of Mixed Reality and computer-assisted evaluation. The possibility of integration of distinct medical imaging modalities and innovative functionalities holds promise for clinical applications. However, it is important to consider issues related to usability, bias, and statistical analyses need consideration. Mixed Reality offers significant benefits, but there are still open challenges such as ergonomic issues, limited field of view, and battery autonomy that must be addressed to ensure widespread acceptance.

Laparoscopic partial nephrectomy (LPN) after hyperselective embolization of tumor vessels (HETV) in a hybrid operating room (HOR) that combines traditional surgical equipment with advanced imaging technology, is a non-clamping surgical approach to treat localized kidney tumors that have shown promising short-term results. The aim of this study was to evaluate the long-term oncological and functional outcomes of this procedure. All consecutive patients treated for a localized kidney tumor by LPN after HETV between May 2015 and October 2022 in a single academic institution were included in the study. Clinical, pathological and biological data were collected prospectively in the uroCCR database. We evaluated perioperative data, postoperative complications, surgical margin and modification of renal function after surgery. We included 245 patients. Median tumor size was 3.2 (2.5-4.4) cm. The R.E.N.A.L. complexity was low, medium and high for 104 (43.5%), 109 (45.6%) and 26 (10.9%) patients, respectively. Median LPN time was 75 (65 -100) min and median blood loss was 100 (50-300) mL. Surgical postoperative complications occurred in 56 (22.9%) patients with 17 (5.7%) major complications. The median preoperative Glomerular Function Rate (GFR) was 90.5 (77-101.8) mL/min and the median GFR variation at 6 months was -7.5 (-15- -2) mL/min. Malignant tumors were present in 211 (86.1%) patients and 12 (4.9%) patients had positive surgical margins. After a median follow-up of 27 (8-49) months, 20 (8.2%) patients had a tumor recurrence and 4 (1.6%) died from cancer. The use of a HOR to perform LPN after HETV is a safe and efficient non-clamping approach to treat localized kidney tumors.

1) Background: Several studies have shown the benefit of drawing when learning anatomy. Virtual Reality (VR) also appears to be useful to increase the understanding of the location of anatomical structures. This study aims to describe how students in an Operating Room Nursing (OR nursing) master study program perceive the benefit of active learning methods, including drawing and the use of VR. 2) Methods: We combined these two methods in a class of 29 students. 38 half-finished drawings of anatomical structures were made. The students were to complete these during lectures with guidance from the teacher. The students also attended a two-hour VR session where they were to find various anatomical structures. A paper questionnaire was applied to evaluate the teaching program. Data were analyzed statistically. 3) Results: The students highly appreciated these learning methods. They reported that drawing made them work more actively during lectures and increased their learning outcome. They also perceived that the use of VR technology increased their understanding of the location of anatomical structures. 4) Conclusion: The combination of drawing and VR technology may be of benefit to OR Nursing students when learning anatomy by both increasing student activity and learning outcomes.

In this work we theoretically investigate the responsivity/noise equivalent power (NEP) trade-off in graphene/semiconductor Schottky photodetectors (PDs) operating in the near-infrared regime and working at room temperature. Our analysis shows as the responsivity/NEP ratio is strongly dependent on the Schottky barrier height (SBH) of the junction and we derive a closed analytical formula for maximizing it. In addition, we theoretically discuss as the SBH is linked to the bias applied to the junction in order to show how these devices could be optimized in practice for different semiconductors. We discover that graphene/n-silicon (Si) Schottky PDs could be optimized at 1550nm showing a responsivity and NEP of 133mA/W and 500fW/Hz, respectively, by a low reverse bias of only 0.66V. Moreover, we show that graphene/n-germanium (Ge) Schottky PDs optimized in term of responsivity/NEP ratio could be employed at 2000nm with a responsivity and NEP of 233mA/W and 31pW/Hz, respectively. We believe that our insights are of great importance in the field of silicon photonics for the realization of Si-based PDs to be employed in power monitoring, lab-on-chip and environment monitoring applications.

Oxide semiconductors are conventionally being used as sensing materials in gas sensors, limiting the detection of gases at room temperature (RT). In this work, a hybrid of copper oxide (CuO) with functionalized graphene (rGO) is proposed to achieve gas sensing at RT. The combination of high surface area and presence of many functional groups in CuO/rGO hybrid material makes it highly sensitive for gas absorption and desorption. To prepare the hybrid material, a copper oxide suspension synthesized using copper acetate precursor is added to the graphene oxide solution during its reduction using ascorbic acid. Material properties of CuO/rGO hybrid and its drop-casted thin films are investigated using Raman, FTIR, SEM, TEM, and four-point probe measurement systems. We find that the hybrid material is enriched with oxygen functional groups (OFGs) and defective sites along with electrical conductivity (~1.5 kΩ/□). The fabricated QCM (quartz crystal microbalance) sensor with a thin layer of CuO/rGO hybrid, demonstrates a high sensing response which is twice the response of the rGO-based sensor for CO₂ gas at RT. We believe that the CuO/rGO hybrid can be highly suitable for existing and future gas sensors used for domestic and industrial safety.

Unexpected preoperative surgery cancellations are one of the important problems in daily anesthesia practice. It's an even bigger problem if these cancellations happen in the operating room. Our aim was to draw attention to this issue and reveal the reasons. This prospective, cross-sectional study aimed to assess the prevalence and causes of elective surgery cancellations once patients are in the operating room. The study sample consisted of 7482 adult patients scheduled for elective surgeries and taken to the operating room. Sixty-seven patients whose surgeries were canceled were grouped into Group 1, while the remaining 7415 whose surgeries were completed were in Group 2. Patients were divided into two groups based on whether their surgeries were completed or canceled. Factors such as age, American Society of Anesthesiologists physical status, and surgical department were analyzed. Metrics involved comparisons between the two groups regarding age, American Society of Anesthesiologists physical status classification, surgical department, and timing of the surgery. The prevalence of elective surgery cancellations after patients were in the operating room was 0.9%. Group 1 was significantly older than Group 2 (p<0.001). The proportion of patients classified as American Society of Anesthesiologists physical status III was higher in Group 1 (p<0.001). The department with the highest cancellation rate was ophthalmology(2.5%), followed by general surgery(2.1%), urology(1.5%), and ear, nose, and throat(1.4%). Approximately 59.7% of cancellations were deemed potentially avoidable. The study suggests that many of these cancellations are potentially avoidable, underscoring the need for optimized surgical scheduling and patient assessment protocols.

Remote Photoplethysmography (rPPG) has emerged as a non-intrusive and promising physiological sensing capability in HCI research, gradually extending its applications in health-monitoring and clinical care contexts. With advanced machine learning models, recent datasets collected in real-world conditions have gradually enhanced the performance of rPPG methods in recovering heart-rate and heart-rate variability metrics. However, the signal quality of reference ground-truth PPG data in existing datasets is by and large neglected, while poor quality references negatively influence models. Here, this work introduces a new imaging blood volume pulse (iBVP) dataset of synchronized RGB and thermal infrared videos with PPG ground-truth signals from the ear and its high resolution signal quality labels, for the first time. Participants perform rhythmic breathing, head-movement, and stress-inducing tasks, which help reflect real-world variations in psycho-physiological states. This work conducts dense (per sample) signal quality assessment to discard noisy segments of ground-truth and corresponding video frames. We further present a novel end-to-end machine learning framework, iBVPNet that features an efficient and effective spatio-temporal feature aggregation for reliable estimation of BVP signals. Finally, this work examines the feasibility of extracting BVP signals from thermal video frames, which is underexplored. The iBVP dataset and source codes are publicly available for research use.

Despite the need for a sustainable energy resource, bioenergy gained its spotlight in the 2000s. Sugarcane is a significant crop in terms of sugar and energy capacity, and it can be an alternative energy source to mitigate the effects of climate change. Bioenergy production from sugarcane in Brazil is one of the most efficient. This production lends a centrality to biofuels' importance in confronting the effects of climate change. The present article reviews the Brazilian history of this crop as a biofuel source. We highlight the historical changes related to scientific, technological, industrial, and environmental advances since the beginning of the 20th century. We describe how creating governmental institutes and disseminating scientific knowledge strengthened public policies that led Brazil to occupy leadership positions in producing, distributing, and using bioenergy throughout the country. The compiled data shows the improvement and the new approaches needed in ethanol sugarcane. We developed a bibliometric analysis to evaluate Brazilian science's contribution to this process compared to other countries. Brazil's history of science and investments in sugarcane biofuel development for transportation may be divided into two phases: ethanol-only and flex-fuel cars. A third phase is starting, which is the ethanol-to-hydrogen era.

Theoretical and experimental approaches have been applied to study the polymer physics under-lying compaction of DNA in the bacterial nucleoid. Knowledge of the compaction mechanism is necessary to obtain a mechanistic understanding of the process of segregation of replicating chromosome arms (replichores) during the cell cycle. In the first part of this review light microscope observations are discussed that have demonstrated that the nucleoid has a lower refractive index and thus a lower density than the cytoplasm. A polymer-physical explanation for this phenomenon was given by the theory of Theo Odijk pro-posed in 1998. By assuming a phase separation between nucleoid and cytoplasm and by imposing equality of osmotic pressure and chemical potential between the two phases, a minimal energy situation is obtained in which soluble proteins are depleted from the nucleoid, thus explaining its lower density. The theory is compared with recent views for DNA compaction that are based on mere exclusion of polyribosomes from the nucleoid or on the transcriptional activity of the cell. These new views raise the question of whether they can still explain the lower refractive index or density of the nucleoid. In the second part of this review the question is discussed how DNA segregation occurs in Esche-richia coli, in the absence of the so-called active ParABS system, present in the majority of bacteria. How is entanglement prevented of nascent chromosome arms, generated at the origin in the pa-rental network of the E. coli nucleoid? The observations of the groups of Sherratt and Hansen in 2006, that the four nascent chromosome arms synthesized in the initial replication bubble, segre-gate to opposite halves of the sister nucleoids implies that extensive intermingling of daughter strands does not occur. Based on the hypothesis that leading and lagging replichores synthesized in the replication bubble, fold into micro-domains that do not intermingle, a passive "four-excluding-arms model" for segregation is proposed. This model implies that the key for seg-regation already lies in the structure of the replication bubble at the very start of DNA replication; it explains the different patterns of chromosome arms as well as the segregation distances between replicated loci as experimentally observed.

We propose a generalized, practitioner-oriented operating leverage model for predicting operating income using Standard and Poor’s Compustat items: SALE (net sales), COGS (cost of sales), DP (total depreciation and amortization), XSGA (selling, general, and administrative expenses), and OIADP (operating income after depreciation and amortization). Prior research finds that OIADP = SALE - COGS - DP - XSGA; hence, our model includes all aggregate revenues and expenses comprising OIADP. Also, prior research finds COGS is “much less” sticky than DP and XSGA; hence, we use COGS as a proxy for total variable costs and DP and XSGA as proxies for sticky fixed costs. We introduce a new adjustment to the textbook operating leverage model so that SALE-to-COGS remains constant for the reference and forecast periods. Also, inspired by prior research, we introduce adjustments to DP and XSGA for cost stickiness. We find our generalized operating leverage model improves estimates of changes in next-quarter and next-year OIADP compared to textbook operating leverage predictions, which are special cases of our model.

In order to overcome the limitation of the traditional adaptive Unscented Kalman Filtering (UKF) algorithm in noise covariance estimation for statement and measurement, we propose a hybrid adaptive UKF algorithm based on combining Maximum a posteriori (MAP) criterion and Maximum likelihood (ML) criterion, in this paper. First, to prevent the actual noise covariance deviating from the true value which can lead to the state estimation error and arouse the filtering divergence, a real-time covariance matrices estimation algorithm based on hybrid MAP and ML is proposed for obtaining the statement and measurement noises covariance, respectively; and then, a balance equation the two kinds of covariance matrix is structured in this proposed to minimize the statement estimation error. Compared with the UFK based MAP and based ML, the proposed algorithm provides better convergence and stability.

With the development of higher voltage power grid, the high and low voltage parallel loops are emerging, which lead to energy losses, even threaten the security and stability of power system. The multi-infeed HVDC configurations widely appearing in AC/DC interconnected power system make this situation even worse. Aimed at energy saving and system security, a decision optimization method for power grid operating condition with high and low voltage parallel loops is proposed in this paper. Firstly, considering hub substation distribution and power grid structure, parallel loop opening schemes are generated with GN algorithm. Then, candidate opening schemes are preliminarily selected from all these generated schemes based on a filtering index. Finally, with the influence on power system security, stability and operation economy in consideration, an evaluation model for candidate opening schemes is founded based on analytic hierarchy process (AHP). And a fuzzy evaluation algorithm is used to find the optimal scheme. Simulation results of New England 39-bus system and an actual power system validate the effectiveness and superiority of this proposed method.

The ongoing challenge to ensure a sustainable and affordable energy supply forces industrial companies to implement appropriate measures. These measures typically lead to an increased system complexity, which has to be addressed during operation. Whereas existing approaches from the field of supervisory and optimal control appear to be capable of mastering this issue, these are still not adopted in industry. Therefore, this work presents a procedure model for the systematic development of application-oriented operating strategies for industrial energy supply systems. The procedure model combines research approaches from the fields of sequencing control and approximate MPC to extract rule-based operating strategies. By splitting the procedure model into five phases, expert knowledge can be integrated in a target-oriented manner. Subsequently to the description, the procedure model is exemplary applied to the example of an industrial heating supply system. Throughout an optimization study, the developed operating strategy is compared to a MPC strategy as well as a baseline strategy. Whereas the conventional MPC approach is the upper bound with regard to optimality, the developed operating strategy is able to generate comparable results. Compared to the baseline strategy, a relative reduction in operating expenses of 5.4 % to 37.0 % are achieved in this specific use case.

This research work explains the practical realization of hybrid solar wind based standalone power system with maximum power point tracker (MPPT) to produce electrical power in rural places (residential applications). The solar inspired Ant Colony Optimization (ACO) based MPPT algorithm is employed for the purpose of fast and accurate tracking power from solar and wind system. Fuzzy Logic Control (FLC) inverter controlling strategy is adopted in this presented work compared to classical PI control. Moreover, single Cuk converter is operated as impedance power adapter to execute MPPT functioning. Satisfactory practical results have been realized using dSPACE (DS1104) platform that justify the superiority of proposed algorithms designed under various operating situations.

A case-crossover study examined how PM_2.5 from Asian Dust Storms (ADS) affects the number of emergency room (ER) admissions for cardiovascular diseases (CVDs) and respiratory diseases (RDs). Our data indicated that PM_2.5 concentration from ADS was highly correlated with ER visits for CVDs and RDs. The odds ratios (OR) increased by 2.92 (95% CI: 1.22-5.08) and 1.86 (95% CI: 1.30-2.91) per increase 10 µg/m³ in PM_2.5 levels, for CVDs and RDs, respectively. A 10 µg/m³ increase in PM_2.5 from ADSs was significantly associated with increase in ER visits for CVDs among those 65 years of age and older (an increase of 2.77 in OR) and for females (an increase of 3.09 in OR). In contrast, PM_2.5 levels had a significant impact on RD ER visits among those under 65 years of age (OR=1.77). The risk of ER visits for CVDs increased on the day when the ADS occurred in Taiwan and the day after (lag 0 and lag 1); the corresponding risk increase for RDs only increased on the fifth day after the ADS (lag 5). In Taiwan’s late winter and spring, the severity of ER visits for CVDs and RDs increases. Environmental protection agencies should employ an early warning system for ADS to reduce high-risk groups’ exposure to PM_2.5.

Lead-acid batteries utilised in electrical substations release hydrogen and oxygen when these are charged. These gases could be dangerous and cause a risk of fire if they are not properly ventilated. Therefore, this research seeks to design and implement a network control panel for heating, ventilation, and air-conditioning systems (HVACS). This is done using a specific range of controllers, which have more than thirty loops of proportional, integral and derivative (PID) control to achieve a cost-effective design. It performs the required function of extracting hydrogen, oxygen, and maintaining the desired temperature of the battery storage room within the recommended limits (i.e. 25°C ±1°C tolerance) without compromising quality as set out in the user requirement specification in Appendix-A. The system control panel allows the user to access control parameters such as changing temperature set-points, fan-speed, sensor database amongst others. The hardware is configured to detect extreme hydrogen and oxygen gas content in the battery room and ensure that the HVACS extract the gas content to the outside environment. The results of the system show that the network control panel effectively operates as per the recommended system requirements. Therefore, the effective operation of the HVACS ensures sufficient gas ventilation, thus mitigating the risk of fire in a typical battery storage room. Furthermore, the effective operation of HVACS enhances battery lifespan because of regulated operating temperature, which is conducive to minimise the effect of sulfation in lead acid Batteries (LABs).

The bipartite entanglement is comprehensively investigated in the mononuclear molecular complex (Et3NH)[Ni(hfac)2L], where HL denotes 2-(2-hydroxy-3-methoxy-5-nitrophenyl)-4,4,5,5-tetramethyl-4,5-dihydro-1H-imidazol-3-oxide-1-oxyl and hfacH stands for hexafluoroacetylacetone. From the magnetic point of view, the molecular compound (Et3NH)[Ni(hfac)2L] consists of an exchange-coupled spin-1 Ni2+ magnetic ion and a spin-12 nitronyl-nitroxide radical substituted nitrophenol. The nickel-radical molecular complex affords an experimental realization of a mixed spin-(12, 1) Heisenberg dimer with a strong antiferromagnetic exchange coupling J/kB= 505 K and two distinct g-factors gRad=2.005 and gNi=2.275. By adopting this set of magnetic parameters we demonstrate that the Zeeman splitting of a quantum ferrimagnetic ground-state doublet due to a weak magnetic field may substantially reinforce the strength of bipartite entanglement at low temperatures. The molecular compound (Et3NH)[Ni(hfac)2L] maintains sufficiently strong thermal entanglement even at room temperature, vanishing only above 546 K. Specifically, the thermal entanglement in the nickel-radical molecular complex retains approximately 40% of the maximum value corresponding to perfectly entangled Bell states at room temperature, which implies that this magnetic compound provides suitable platform of a molecular qubit with potential implications for room-temperature quantum computation and quantum information processing.

Attribute reduction is a core technique in the rough set domain and an important step in data preprocessing. Researchers have proposed numerous innovative methods to enhance the capability of attribute reduction, such as the emergence of multi-granularity rough set models, which can effectively process distributed and multi-granularity data. However, these innovative methods still have many shortcomings, such as how to deal with complex constraints and how to perform multi-angle effectiveness evaluations. Based on the multi-granularity model, this study proposes a new method of attribute reduction, namely using multi-granularity neighborhood information gain ratio as the measurement criterion. This method combines both supervised and unsupervised perspectives, and by integrating multi-granularity technology with neighborhood rough set theory, constructs a model that can adapt to multi-level data features. This model can select the optimal granularity level or attribute set according to the requirements. Finally, the proposed method is experimented with on 15 UCI datasets against six other attribute reduction algorithms. The experimental outcomes, upon analysis and comparative review, substantiate the reliability and consistency of the attribute reduction approach introduced in this study.

By taking advantage of a stability criterion established recently, the critical temperature T_c is reckoned with help of the microscopic parameters, characterising the normal and superconducting electrons, namely the independent-electron band structure and a repulsive two-electron force. The emphasis is laid on the sharp T_c dependence upon electron concentration and inter-electron coupling, which might offer a practical route toward higher T_c values and help to understand why high-T_c compounds exhibit such remarkable properties.

This work presents a novel approach for the study of the movement of droplets on inclined surfaces under the influence of gravity and chemical heterogeneities. The developed numerical methodology uses data-driven modeling to extend the applicability limits of an analytically derived reduced-order model for the contact line velocity. More specifically, while the reduced-order model is able to capture the effects of the chemical heterogeneities to a satisfactory degree, it does not account for gravity. To alleviate this shortcoming, datasets generated from direct numerical simulations are used to train a data-driven model for the contact line velocity, which is based on the Fourier neural operator and corrects the reduced-order model predictions to match the reference solutions. This hybrid surrogate model, which comprises of both analytical and data-driven components, is then integrated in time to simulate the droplet movement, offering a speedup of five orders of magnitude compared to direct numerical simulations. The performance of this hybrid model is quantified and assessed in different wetting scenarios, by considering various inclination angles and values for the Bond number, demonstrating the accuracy of the predictions as long as the adopted parameters lie within the ranges considered in the training dataset.

SARS-CoV-2 is the Coronavirus responsible for the COVID-19 pandemic. Even though we are no more in a pandemic situation, people are getting infected some of them needing hospitalization, and a few of them die. Methods: We did a retrospective study including 445 patients who accessed the Emergency Section of Policlinico Umberto I, Rome, Italy, where they had routine blood exams. In this study, we concentrated on the complete blood count, creatinine, and azotemia. The data was analyzed using ANOVA, Spearman correlation, and ROC analysis. They were divided into four groups based on their outcome: (1) the emergency group (patients with mild forms who were quickly discharged); (2) the hospital ward group (patients who after admission to the emergency section were hospitalized in a COVID-19 ward); (3) the intensive care unit (ICU) group (patients that after the admission in the emergency section required intensive assistance); (4) the deceased group (patients that after the admission in the emergency section had a fatal outcome). Results: We found significant changes for creatinine, azotemia, hematocrit, mean corpuscular hemoglobin concentration, basophils, monocytes, red blood cell distribution width, hemoglobin, hematocrit, and red blood cell numbers by ANOVA according to their outcomes, particularly for the deceased group. Also, we found outcome correlations for eosinophils, hemoglobin, hematocrit, mean corpuscular hemoglobin concentration, lymphocyte, neutrophil, platelet, and red blood cell number and red blood cell distribution width. Conclusions: This study discloses an association between “classical” routine blood biomarkers and the severity of outcomes in Omicron patients.

As the natural resources are getting exhausted, the concept of sustainable development of region has received increasing attentions, especially for resource-dependent cities. In this paper an innovative method that emergy analysis and IPAT (Human Impact Population Affluence Technology) model were combined in order to analyze the quantitative relationship of economic growth and energy consumption and further to evaluate its overall sustainability level. Taiyuan, a traditional, resource-dependent city in China, is selected as the case study region. The main results show that total emergy of Taiyuan increased from 9.023× 1023 sej in 2007 to 9.116× 1023sej in 2014, with 38% reduction on non-renewable emergy and 125% growth on imported emergy. Regional emergy money ratio (RMB) was reduced by 48% from 5.31× 1013sej/$ in 2007 to 2.74× 1013sej/$ in 2014, indicating that the increasing speed of consuming resources and energy was faster than the increase of GDP, and that Taiyuan’s money purchasing power declined. The lower emergy sustainability index (ESI) indicates that Taiyuan was explored and produced large quantities of mineral resources, which puts more stress on the environment as a consequence, and that this is not sustainable in the long run. The IPAT analysis demonstrates that Taiyuan sticks to the efforts of energy conservation and environmental protection, in order to promote regional sustainable development, it is necessary to take an integrated effort. Policy insights suggest that resourceful regions should improve include energy and resource efficiency, optimizing energy and resourceful structure.

In this paper, a novel permanent magnet-assisted synchronous reluctance machine (PMASynRM) with rare-earth PMs and ferrite magnets is proposed. The performance of PMASynRM is discussed with respected to the different magnet ratio of rare-earth PMs and ferrite magnets. Some characteristics including the flux density, output torque, cogging torque, output power, power factor, torque ripple, loss, efficiency, and demagnetization are calculated by 2-D finite element analysis (FEA). The analysis results show that the excellent performance can be obtained by using hybrid magnet of rare-earth PMs and ferrite magnets with the suitable magnet ratio, and provide some desirable cost-performance trade-off.

Graphene hybrid-filler polymer composites have emerged as prominent materials that revolutionize heavy industries. This study encapsulates the in-depth analysis of different influential factors such as filler/graphene type, aspect ratios, dispersion methods, filler-matrix compatibility, fiber orientation, synergistic effects, different processing techniques, and post-curing conditions that affect the processing, properties and determine the resultant applications of graphene hybrid polymer composites. Additionally, it discusses the substantial role of graphene collaboration with other fillers such as carbon nanotubes, silica, nano-clays and metal oxides to produce functionalized hybrid polymer composites with synergistically enhanced tailored properties to offer solutions for heavy industries like aerospace, automotive, electronics, and energy harvesting. The review concludes with some suggestions and outlook on the future of these composite materials by emphasizing the need for continued research to fully optimize their potential.

A low-cost bio-mass-derived carbon substrate has been employed to synthesize MoS₂@carbon composites through a hydrothermal method. Carbon fibers derived from natural cotton provide a three-dimensional and open framework for the uniform growth of MoS₂ nanosheets, thus constructing hierarchically coaxial architecture. The unique structure could synergistically benefit fast Li-ion and electron transport from the conductive carbon scaffold and porous MoS₂ nanostructures. As a result, the MoS₂@carbon composites, when served as anodes for Li-ion batteries, exhibit a high reversible specific capacity of 820 mAh g^-1, high-rate capability (457 mAh g^-1 at 2 A g^-1), and excellent cycling stability. The superior electrochemical performance makes the MoS₂@carbon composites to be low-cost and promising anode materials for Li-ion batteries.

Lily tepals have a short lifespan. Once the tepals senesce, the ornamental value of the flower is lost. Some cultivars have attractive purple ovaries and fruits which greatly enhance the ornamental value of Asiatic hybrid lilies. However, little is known about the molecular mechanisms of anthocyanin biosynthesis in Asiatic hybrid lily ovaries. To investigate the transcriptional network that governs purple ovary coloration in Asiatic hybrid lilies, we obtained transcriptome data from green ovaries (S1) and purple ovaries (S2) of Asiatic ‘Tiny Padhye’. Comparative transcriptome analysis revealed 4228 differentially expressed genes. Differential expression analysis revealed that nine unigenes including four CHS genes, one CHI gene, one F3H gene, one F3′H gene, one DFR gene, and one UFGT gene were significantly up-regulated in purple ovaries. One MYB gene, LhMYB12-Lat, was identified as a key transcription factor determining the distribution of anthocyanins in Asiatic hybrid lily ovaries. Further qPCR results showed unigenes related to anthocyanin biosynthesis were highly expressed in purple ovaries of Asiatic ‘Tiny Padhye’ at stages 2 and 3, while they showed an extremely low level of expression in ovaries of Asiatic ‘Yellow Pixels’ during all developmental stages. In addition, shading treatment significantly decreased pigment accumulation by suppressing the expression of several unigenes related to anthocyanin biosynthesis in ovaries of Asiatic ‘Tiny Padhye’. These results could further our understanding of the molecular mechanisms of anthocyanin biosynthesis in Asiatic hybrid lily ovaries.

ZnO has many technological applications which largely depend on its properties that can be tuned by controlled synthesis. Ideally, the most convenient ZnO synthesis is carried out at room temperature in aqueous solvent. However, the correct temperature values are often loosely defined. In the current paper we performed synthesis of ZnO in aqueous solvent, by varying reaction and drying temperature by 10°C steps and monitored the synthesis products primarily by XRD. We found out that a simple direct synthesis of ZnO, without additional surfactant, pumping of freezing, required both a reaction (TP) and a drying (TD) temperature of 40°C. Higher temperatures also afford ZnO, but lowering any of the TP or TD below the threshold value results either in the achievement of Zn(OH)2 or in a mixture of Zn(OH)2/ZnO. A more detailed Rietveld analysis of the ZnO samples reveals a density variation with the synthesis temperature and an increase of the nanoparticles average size also verified by SEM images. The optical properties of ZnO obtained by UV-Vis reflectance spectroscopy indicate a red shift of the band gap by ~0.1 eV.

As marine traffic is contributing to pollution and mostly have predictable route with repetitive load profiles, to reduce their impact on environment, hybrid system with proton exchange membrane fuel cells (PEMFC-s) and battery pack, is promising replacement. For this purpose, the numerical model of repowered existing vessel that have two diesel engines with 300 kWe is developed. The goal of this paper is to develop numerical model which analyzes and determine equivalent hybrid ship propulsion system for known traveling route. The developed numerical model consists of an interconnected system with PEMFC stack and battery pack as power sources. Numerical model is developed and optimized to meet minimal required power demand for successful route demand, which has variable loads and daily sails six-time same voyage- in total 54 nautical miles. The results have shown that equivalent hybrid power system consists of 300 kWe PEMFC stack and battery pack with 424 kWh battery and state of charge varying between 20 and 87%. To power this new hybrid power system, hydrogen tank of 7200 l holding 284.7 kg at pressure of 700 bar is needed, compared to previous system that spend 1524 kg of diesel and generate 4886 kg of CO2.

Hybrid materials are a recent addition in the field of Restorative Dentistry for computer-assisted design/ computer-assisted manufacturing (CAD/CAM) indirect restorations. The long–term clinical success of modern dental restorative materials follows a multifactorial pattern. Among the characteristics, affecting the longevity of a restoration, mechanical properties and physicο – chemical interactions are of utmost importance. While numerous researchers constantly evaluate the mechanical properties, the biological background of resin–based CAD/CAM biomaterials is scarcely investigated and, therefore, less described in the literature. This review aims to analyze the biofilm formation on the surfaces of novel hybrid, resin–based CAD/CAM materials and evaluate the methodological protocols followed to assess microbial growth. It is demonstrated that the surface structure, the composition and the finishing and polishing procedures on the surface of a dental restorative material influence the initial bacterial adhesion; however most studies focus on in vitro protocols, whereas in vivo and/or in situ research of microbiomics in CAD/CAM restorative materials is lacking, obstructing in that manner the accurate understanding of the bioadhesion phenomenon in the oral cavity.

This article introduces a novel payload structure, which has been experimentally proven to have smaller impact force while the carried internal electronics remains intact. The study describes in details how materials and geometric structures were chosen based on information analysis. It is clarified how possible geometric structures and materials can be chosen to yield optimal efficiency. Finite element method simulations were carried out to investigate the mechanical properties of several geometric structures, which has led to the dodecahedron form. For the frame, Polylactic Acid were chosen as an optimal material. A low air pressure test for parts of the structure, and also the whole structure were carried out with successful results. Drop tests, with force measuring sensors and high speed videos, were carried out for measuring and comparing the maximal impact force of classical payloads and the novel one. Laboratory and real life tests demonstrated that the developed new structure is safer and it is applicable.

This paper puts forward an alteration for Tensor Calculus utliized in a coordinate system which is under a dynamic distortion drawing inspiration from similar fields such as the Calculus of Moving Surfaces (CMS). The paper establishes transformation laws for Tensors within these regions and establishes Operators such as the Tensorial Field Derivative which enforce a Tensorial Transformation on Tensors defined within a Dynamically Moving coordinate system. This variation of Tensor Calculus can be utilized to observe how disciplines such as QFT and Continuum Mechanics would change to accomodate for a distorting coordinate system and can be utliized to develop new theoretical models which account for this temporal distortion particularly within Biological Settings.

In the dynamic and complex environment of industrial control rooms, operators are often inundated with a multitude of tasks and alerts, which can lead to an overwhelming situation known as task overload. This state can precipitate decision fatigue and a heavier reliance on cognitive biases, potentially compromising the decision-making process. To mitigate such risks, the implementation of decision support systems becomes crucial. These systems are designed to assist operators in making swift and well-informed decisions, particularly when they sense their own judgment may be faltering. Our research introduces an AI-based framework that leverages dynamic influence diagrams and reinforcement learning to construct an effective decision support system. The cornerstone of this framework is the creation of a robust, interpretable, and efficient tool that supports control room operators during critical process disturbances. By integrating expert knowledge, the dynamic influence diagram forms a comprehensive model that captures the uncertainties inherent in complex industrial processes. It is adept at anomaly detection and recommending optimal actions. Moreover, this model is enhanced through a strategic partnership with reinforcement learning algorithms, which fine-tune the recommendations to be more context-specific and precise. The ultimate goal of our framework is to provide operators with a live, reliable decision support system that can significantly improve their response during process upsets. This paper outlines the development of our AI framework and its application within a simulated control room environment. Our findings indicate that the use of decision support systems can lead to improved operator performance and reduced cognitive workload. However, it also reveals a trade-off with situation awareness, which tends to diminish as operators may become overly reliant on the system’s guidance. Trust emerges as a critical factor in the adoption and effectiveness of decision support systems. Our research underscores the importance of balancing the benefits of decision support with the need for maintaining operator engagement and comprehension during process operations.

Annually, an estimated 13-26 million newborns need respiratory support and 2-3 million newborns need extensive resuscitation, defined as chest compression and 100% oxygen with or without epinephrine in the delivery room. Despite such care, there is a high incidence of mortality and short-term neurologic morbidity. The poor prognosis associated with receiving chest compression alone or with medications in the delivery room raises questions as to whether improved cardiopulmonary resuscitation methods specifically tailored to the newborn could improve outcomes. This review discusses the current recommendations, mode of action, different compression to ventilation ratio, continuous chest compression with asynchronous ventilations, chest compression and sustained inflation optimal depth, and oxygen concentration during cardiopulmonary resuscitation.

Preventive Maintenance (PM) is a periodic maintenance strategy, which has great results for devices in extending their life, increasing productivity, and most importantly, help avoid unexpected breakdowns and their costly consequence. A preventive maintenance scheduling (PMS) is determining the time for carrying out PM, and it represents a sensitive issue in terms of impact on production if the time for the PM process is not optimally distributed. In this study, hybrid heuristic methods were used to solve the PMS problem, as genetic algorithm and Tabu research were adopted. The optimal solution was reached in a short time compared to previous studies in which optimal methods were used, integer programming and nonlinear integer programming. Also, sensitivity analysis was applied to measure the robustness and strength of the method used, where an optimal solution was obtained for all experiments and in record time. This method can be used for power plants in privet or public sectors, to generate an optimal PMS, to save money, and to avoid water or electricity cuts.

A hybrid material, consisting of commercially available nitrocellulose (NC) membrane non-covalently modified with amino-polyethylene glycol functionalized reduced graphene oxide (NH2-PEG-rGO) nanoparticles, was successfully synthesized for oligonucleotide extraction. Fourier Transform Infrared Spectroscopy (FTIR) confirmed the modification of the NC membrane, revealing characteristic peaks of both compounds NC and NH2-PEG-rGO. Scanning Electron Microscopy (SEM) exhibited morphological changes in the NC/NH2-PEG-rGO hybrid membrane, marked by the introduction of NH2-PEG-rGO particles, resulting in a distinctly smothered surface compared to the porous surface of the NC control membrane. Wettability assays revealed hydrophobic behavior for the NC/NH2-PEG-rGO hybrid membrane, with a water contact angle exceeding 90°, contrasting with the hydrophilic behavior characterized by a 16.7° contact angle in the NC membrane. The performance of the NC/NH2-PEG-rGO hybrid membrane was evaluated for the extraction of ssDNA with fewer than 50 nucleotides from solutions containing various ionic species (MnCl2, MgCl2, and MnCl2/MgCl2). The NC/NH2-PEG-rGO hybrid membrane exhibited optimal performance when incubated in MgCl2, presenting the highest fluorescence emission at 525 relative fluorescence units (r.f.u.). This corresponds to the extraction of approximately 610 pg (≈13%) of the total oligo-DNA, underscoring the efficacy of the pristine material, which extracts 286 pg (≈6%) of oligo-DNA in complex solutions.

In the era of mounting water scarcity, particularly in arid regions, the agricultural sector is striving to optimize the water resource management practices. Treated wastewater (TWW) has emerged as a viable alternative to freshwater for irrigation, offering a sustainable solution to water conservation. However, ensuring the safety and quality of TWW is paramount to safeguard for both crop health and environmental integrity. Electrical conductivity (EC), a critical factor in assessing TWW suitability for irrigation, can significantly impact crop yields and soil health since it is directly linked to the concentration of dissolved salts and ions. Therefore, this study delves into the development of advanced predictive models for EC assessment by employing supervised machine learning (ML) techniques like the Support Vector Regression (SVR), Adaptive Network-based Fuzzy Inference System (ANFIS), and Multiple Linear Regression (MLR). The TWW samples collected from Al-Qatif area, Saudi Arabia were assessed in the lab through a sensor-based real-time monitoring system integrated with Internet of Things (IoT) network and a multiprobe device. The key water quality parameters assessed involved, temperature (T), pH, Oxidation Reduction Potential (ORP), Resistivity (RES), Total Dissolved Solids (TDS), Salinity and Turbidity which served as the foundation for these models, given their profound influence on and their anticipated impact on EC levels. Following feature selection, two distinct model combinations were identified for the SVR, ANFIS and MLR models. Furthermore, to evaluate prediction performance, four statistical criteria, including coefficient of determination (R²), correlation coefficient (R), mean square error (MSE), and root mean square error (RMSE), were employed. Overall, the comparative performance results proved that ANFIS-M2 indicated the strongest predictive capability with the R² value of 0.99572 and 0.75145 and the RMSE values of 0.00965 and 0.01134, respectively in both calibration and verification stages.

Regular regimes of oil and oil products pipelines are studied. The problem is to develop an algorithm of effective pipeline system control that ensures the fulfillment of specified boundary conditions at the system boundaries. The product is pumped in batches, the flow is characterized by a change in temperature and pressure flow parameters over time. The developed solution method uses the principle of decomposition in the sense that each computational iteration is im-plemented in 3 stages, in three nested loops. The inner cycle is connected with the material bal-ance relations, at the next cycle the flow equations are introduced and the fulfillment of the 2nd Kirchhoff's law is monitored. If the flow process is significantly affected by temperature, then an external cycle is also implemented, correcting the solution so that the energy conservation equa-tion is satisfied. In the calculation procedure, some computational difficulties may arise, which consist in choosing an appropriate optimization method. On a specific example, the possibility of using various library programs to solve the problem was checked. The developed method is suita-ble for the analysis of systems of arbitrary topology. Since the method is not time-consuming, it can be recommended for online control of oil and oil products supply systems. The paper opens a new direction in the theory of hydraulic circuits. It uses both traditional methods of continuum mechanics and stochastic models.

This paper outlines the detection procedure of intrusion as provided by Tripwire tool along-with the enhancement to be made in design and implementation to achieve the optimum performance level of Tripwire. It operates on effective and swift performance mechanism in order to report the system admin about the possible intrusion detected in the system with security assurance in cutting edge computer structures, which is very important in order to provide the integrity and reliability of information. In order to deal with this emerging issue in the historical research, the basic level of security is provided in the system by making enhancement in the existing tripwire tool for UNIX file system. The proposed methodological working of tripwire makes it more effective by adopting reliable and instantaneous mechanism to deal with specifically anomalies and unwanted access in the UNIX file system.

A multiscale model that enables quantitative understanding and prediction of the size effect on scattering properties of micro- and nanostructures is crucial for the design of LED surface textures optimized for high light extraction efficiency (LEE). In this paper, a hybrid process for combining full-wave finite-difference time-domain simulation and a ray-tracing technique based on a bidirectional scattering distribution function model is proposed. We apply this method to study the influence of different pattern sizes of a patterned sapphire substrate on GaN-based LED light extraction from the microscale to the nanoscale. The results show that near-wavelength–scaled patterns with strong diffraction are not expected to enhance LEE. By contrast, microscaled patterns with optical diffusion behavior have the highest LEE at a specific aspect ratio, and subwavelength-scaled patterns that have antireflection properties show marked enhancement of LEE for a wide range of aspect ratios.

Hybrid reinforcement in a composite material (CM), in many situations, allows better govern material mechanical properties. Polymer matrix CM plate is reinforced with small particles and macro-fibers. Particles are oil shale ash (OSA) powder, macro-fibers – basalt fiber threads im-pregnated by matrix material. With the goal to find out elastic properties of the matrix- polymer with OSA, samples with its different concentrations were experimentally fabricated and their elastic properties were experimentally measured. Obtained data were used in numerical model-ling. Was observed polymer matrix composite slab, reinforced with OSA and three-dimensional (3D) basalt fiber fabric. Fabric are forming threads impregnated by matrix (polymer resin mixed with OSA particles). Damage accumulation in the stretched slab was modelled. Impregnated thread, in the modelling, is observed as a macro-fiber (MF) with averaged elastic properties. With the load increase MF in the material began to break. At first, appeared isolated single breaks. A probabilistic sequential MF rupture accumulation model was accepted and numerical-ly realized. The geometry of the reinforcing knitted fabric was modeled using the Leaf and Glaskin approach. In the knitted fabric highly, stressed MF cross-sections are observed as po-tential location where thread breakage can occur. If one thread breaks, the cross-sections of the adjacent threads experience the overload caused by this rupture. More overloaded crossection in the adjacent overloaded thread breaks and we obtain two adjacent broken MF designated as a defect with the size j=2. The probabilities of obtaining defect consisting of at least 2, 3, … j adjacent broken MF in the plate were calculated. The calculations continued until the rupture process becomes unstable (j→∞). The overstresses on adjacent threads in the CM were calculat-ed using the FEM three-dimensional numerical approach. Analytical and stochastic methods were used for the load-carrying capacity determination and different size defects accumulation in the hybrid composite material (HCM) plate. Also, was calculated the probability of the plate rupture.

This paper presents a two-stage ADC based on pseudo-differential operational transconductance amplifier (OTA), which is designed for the readout circuit of X-ray linear array sensor. This hybrid ADC employs an incremental sigma-delta ADC and a cyclic ADC, achieving a good trade-off between accuracy and conversion speed. The two stages share the same hardware to reduce power consumption and die area. A common-mood feedback module is used to suppress the influence of charge injection, and the effectiveness is demonstrated by detailed theoretical analysis. A test chip of 14-bit ADC is fabricated in 0.35μm CMOS technology. The measured root mean square (RMS) value of DNL is 0.254 LSB, and the maximum value of INL is -0.776/+1.56 LSB. The measured effective number of bits (ENOB) is 13.43 bits.

Layout estimation is a challenge of segmenting a cluttered room image into floor, walls and ceiling. We applied Double refinement network proved to be efficient in the depth estimation to generate heat maps for room key points and edges. Our method is the first not using encoder-decoder architecture for the room layout estimation. ResNet50 was utilized as a backbone for the network instead of VGG16 commonly used for the task, allowing the network to be more compact and faster. We designed a special layout score function and layout ranking algorithm for key points and edges output. Our method achieved the lowest pixel and corner errors on the LSUN data set. The input image resolution is 224*224.

Computational simulations of three-dimensional flow around a NACA 0018 wing with an aspect ratio of AR=5 are carried out using the Unsteady Reynolds-Averaged Navier-Stokes (URANS) equations with the Shear-Stress Transport turbulence model closure. Simulations were performed to capture the aerodynamic stall hysteresis using a developed Pseudo-Transient Continuation (PTC) method based on a dual time step approach in the CFD code OpenFOAM. The flow was characterized by an incompressible Mach number of M=0.12 and a moderate Reynolds number Re=0.67×10^6. The results obtained indicate the presence of a noticeable aerodynamic hysteresis in the static dependencies of the force and moment coefficients, as well as the manifestation of bi-stable flow separation patterns, accompanied by the development of asymmetry in the stall zone. The URANS simulation results are in good agreement with the experimental data obtained for the NACA 0018 finite aspect ratio wing from the low-speed wind tunnel under the same test conditions. A new phenomenological bifurcation model of aerodynamic stall hysteresis under static and dynamic conditions is formulated, which is proven to be able to closely match the experimental data.

This investigation mainly focused on the microstructural analysis of Al based hybrid metal matrix composites. Aluminium as base metal and reinforced with 2% B4 C, ZrO2 (2%,4%,6%), SiC (4%,8%,12%). Specimens were manufactured by using conventional stir casting technique. Hybrid metal matrix composites were examined by using Scanning electron microscope. This research explained XRD, EDS and Fractography analysis. This investigation shows the reinforced material has given better results in all aspects than pure Al6061 alloy and homogeneous dispersion of particles inside the matrix. Porosity, delamination, cracks, particle distributions were observed through microstructural analysis. Additionally determined the crystal size of pure Aluminium 6061 alloy and hybrid composites.

Hybrid Renewable Energy Systems (HRES) integrate renewable sources, storage, and optionally conventional energies, offering an eco-friendly solution to fossil fuels. Microgrids (MGs) bolster HRES integration, enhancing energy management, resilience, and reliability at various levels. This study, emphasizing the need for refined optimization methods, investigates three themes: renewable energy, microgrid, and multiobjective optimization (MOO), through a bibliometric analysis of 470 Scopus documents from 2010-2023, analyzed with SciMAT software. It segments the research into two periods, 2010-2019 and 2020-2023, revealing a surge in MOO focus, especially in the latter period, with a 35% increase in MOO-related research. This indicates a shift towards com-prehensive energy ecosystem management that balances environmental, technical, and economic elements. The initial focus on MOO, genetic algorithms, and energy management systems has expanded to include smart grids and electric power systems, with MOO remaining a primary theme in the second period. The increased application of Artificial Intelligence (AI) in optimizing HMGS within the MOO framework signals a move towards more sustainable, intelligent energy solutions. Despite progress, challenges remain, including high battery costs, the need for reliable MOO data, the intermittency of renewable energy sources, and HMGS network scalability issues, highlighting directions for future research.

: The crystallization conditions from the solution play an important role in determining the mor-phology, phase composition, and photovoltaic properties of perovskite films. Post-processing of the obtained films can have a crucial role in increasing the grain size of perovskite and enhancing its crystallinity. It has been shown that the formation of crystal nuclei can be utilized to accelerate crystallization. In this case, crystallization occurs through the growth of seed crystals created in the solution, enabling the formation of relatively large crystals. For the deposition of CH3NH3PbI3 hybrid halide perovskite films from a solution of the perovskite in dimethylformamide the spin coating technique was employed. Pre-crystallization was achieved by annealing the films at a temperature of 100 or 110 °C. The dissolution process involved adding a drop of dimethylformamide onto the substrate surface and allowing it to partially dissolve the perovskite film. Subsequently, residual solvent was removed through spin coating. The mor-phological analysis of the perovskite film surface after recrystallization at temperatures ranging from 80 to 130 °C was performed. The infrared transmission spectra of the obtained perovskite films were investigated, and their light absorption characteristics were studied through transmission spectra. The perovskite structure in the obtained films was confirmed by the peaks observed in the X-ray diffraction patterns.

Under the background that the international technological innovation environment VUCA has been intensifying and the innovation situation of Chinese manufacturing enterprises has been impacted, the innovation dilemma faced by enterprises has attracted increasing attention, while the innovation dilemma is also one of the important factors affecting the operation efficiency of enterprises. Based on the micro-data of China’s A-share manufacturing listed enterprises, this paper empirically analyzes the impact of innovation dilemmas faced by enterprises on operational efficiency (innovation dilemmas are measured by the difference when actual innovation performance is lower than expected innovation performance). The results show that the innovation dilemma of manufacturing enterprises significantly inhibits the operational efficiency of manufacturing enterprises by reducing their risk tolerance, development ability expectation and profitability. After using a series of tests, such as instrumental variable method, propensity score matching method, DID (Differences-in-Differences) and changing variable measure method, the conclusion is still robust. In addition, the inhibitory effect of innovation dilemma on enterprise operation efficiency is more obvious for private enterprises, small and medium-sized enterprises, enterprises in the ascend or decline phase, high-tech enterprises and enterprises in the eastern region. Therefore, the government should strengthen the policy support for the manufacturing enterprises in the innovation dilemma, help the enterprises to overcome the innovation bottleneck. Manufacturing enterprises themselves should enhance their innovation capabilities and strive to get rid of the innovation dilemma in order to maintain a stable footing in the fierce market competition and improve the high-quality development of China’s manufacturing industry.

The classification of Trojans in modern analog microcircuits is considered. Using high-speed operational amplifiers (Op-Amps) as an example, the relationship between Op-Amp circuit design and the formation of undesirable states in typical switching circuits is shown. Circuit solutions are proposed to minimize the Trojan states of high-speed Op-Amps. These include limiting the maximum output currents of the input stages of the Op-Amp during the transient process and the use of differentiating transient correction circuits in the Op-Amp.

Thermal-based actuators are known for generating large force and displacement strokes at mesoscale (millimeter) regime. In particular, two-phase thermal actuators are found to benefit from the scaling laws of physics at mesoscale to offer large force and displacement strokes; but they have low thermal efficiencies. As an alternative, a combustion-based thermal actuator is proposed and its performance is studied in both open and closed cycle operations. Through a physics-based lumped-parameter model, we investigate the behavior and performance of the actuator using a spring-mass-damper analogy and taking an air standard cycle approach. Three observations are reported: (1) the mesoscale actuator can generate peak forces of up to 400 N and displacement strokes of about 16 cm suitable for practical applications; (2) an increase in heat input to the actuator results in increasing the thermal efficiency of the actuator for both open and closed cycles; and (3) for a specific heat input, both the open and closed cycle operations respond differently \textemdash different stroke lengths, peak pressures, and thermal efficiencies.

The use of renewable fuels for internal combustion engines marks a significant stride towards sustainability in transportation and power generation. Ensuring the compatibility of these fuels with existing diesel engines and infrastructure is paramount for a smooth transition. Diesel engines ca-pable of harnessing the advantages of alternative fuels without extensive modifications offer a pragmatic approach to sustainable power for vehicles and industries. This article investigates the impact of carbon neutral renewable fuel types (HVOs and biodiesel) on the operation of the high-pressure injection pump, focusing on rotational speed and delivery pressure as key parame-ters. Investigations, based on pump operating cycle analysis and volumetric efficiency measure-ments, reveals that while speed dependence is moderate, fuel type significantly influences pump performance. Hydrogenated carbon-neutral fluids (HVOs) demonstrate adequate capabilities compared to conventional fossil fuels, offering promising prospects for reducing environmental impact. The findings underscore the importance of considering fuel properties, particularly com-pressibility modulus. These insights provide valuable guidance for the advancement of sustainable transportation and industrial systems.

In this paper, we introduce hybrid numbers with Fibonacci and Lucas hybrid number coefficients. We give the Binet formulas, generating functions, exponential generating functions for these numbers. Then we define an associate matrix for these numbers. In addition, using this matrix, we present two different versions of Cassini identitiy of these numbers.

All-solid-state lithium batteries (ASSLBs) using argyrodite electrolyte materials have shown promise for applications in electric vehicles (EVs). However, understanding the effects of pro-cessing parameters on the ionic conductivity of these electrolytes is crucial for optimizing battery performance and manufacturing methods. This study investigates the influence of electrolyte op-erating temperature, electrolyte operating pressure, electrolyte pelletization pressure, and electro-lyte pelletizing temperature on the ionic conductivity of Li6PS5Cl0.5Br0.5 argyrodite electrolyte (AmpceraTM, D50=10 µm). A specially designed test cell is employed for the experimental meas-urements, allowing for controlled pelletization and testing within the same tooling. The results demonstrate the significant impact of the four parameters on the ionic conductivity of the argy-rodite electrolyte. The electrolyte operating temperature has a more pronounced effect than oper-ating pressure, and pelletizing temperature exerts a greater influence than pelletizing pressure. This study provides graphs that aid in understanding the interplay between these parameters and achieving desired conductivity values. It also establishes a baseline for the maximum pelletizing temperature before undesirable degradation of electrolyte occurs. By manipulating the pelletizing pressure, operating pressure, and pelletizing temperature, battery engineers can achieve the desired conductivity for specific applications. The findings emphasize the need to consider operating conditions to ensure satisfactory low-temperature performance, particularly for EVs. Overall, this study provides valuable insights into processing and operating conditions for ASSLBs utilizing Li6PS5Cl0.5Br0.5 argyrodite electrolyte.

We characterize the performance of a system based on a magnetoresistor array. This instrument is developed to map the magnetic field, and to track a dipolar magnetic source in the presence of a static homogeneous field. The position and orientation of the magnetic source with respect to the sensor frame is retrieved together with the orientation of the frame with respect to the environmental field. A nonlinear best-fit procedure is used, and its precision, time performance, and reliability are analyzed. This analysis is performed in view of the practical application for which the system is designed that is an eye-tracking diagnostics and rehabilitative tool for medical purposes, which require high speed ($\ge 100$~Sa/s) and sub-millimetric spatial resolution. A throughout investigation on the results makes it possible to list several observations, suggestions, and hints, which will be useful in the design of similar setups.

The ACC feature when activated augments the engine performance in real-time. This article presents a novel methodology to predict the optimal adaptive cruise control set speed profile (ACCSSP) by considering all the effecting parameters. This paper investigates engine operating conditions (EOC) criteria to develop a predictive model of ACCSSP in real-time. We developed a deep learning (DL) model using the NARX method to predict engine operating point (EOP) mapping the vehicle-level vectors (VLV). We used real-world field data obtained from Cadillac test vehicles driven by activating the ACC feature for developing the DL model. We used a realistic set of assumptions to estimate the VLV for the future time steps for the range of allowable speed values and applied them at the input of the developed DL model to generate multiple sets of EOP’s. We imposed the defined EOC criteria on these EOPs, and the top three modes of speeds satisfying all the requirements are derived for each second. Thus three eligible speed values are estimated for each second, and an additional criterion is defined to generate a unique ACCSSP for future time steps. Performance comparison between predicted and constant ACCSSPs indicates that the predictive model outperforms constant ACCSSP.

Accurate classification of objects in 3D point clouds is a significant problem in several applications, such as autonomous navigation and augmented/virtual reality scenarios, which has become a research hot spot. In this paper, we presented a deep learning strategy for 3D object classification in augmented reality. The proposed approach is a combination of the GRU and LSTM. LSTM networks learn longer dependencies well, but due to the number of gates, it takes longer to train; on the other hand, GRU networks have a weaker performance than LSTM, but their training speed is much higher than GRU, which is The speed is due to its fewer gates. The proposed approach used the combination of speed and accuracy of these two networks. The proposed approach achieved an accuracy of 0.99 in the 4,499,0641 points dataset, which includes eight classes (unlabeled, man-made terrain, natural terrain, high vegetation, low vegetation, buildings, hardscape, scanning artifacts, cars). Meanwhile, the traditional machine learning approaches could achieve a maximum accuracy of 0.9489 in the best case.

The surface behavior of the ZnO-based films could be modulated via a postannealing and ultraviolet (UV) irradiation with different powers and time, respectively. These present results could provide modulate the microstructure related in grain-size distribution and photocatalytic behavior for potential guide in the field of wide bandgap semiconducting oxides. The ZnO films were prepared onto Corning-1737 glass substrates by using radio-frequency magnetron sputtering without supplying oxygen source at room temperature. For the purpose of obtaining modulable grain microstructures, the as-prepared ZnO films (Z0) were treated via a postannealing modification in vacuum furnace at 300°C for 30 minutes after deposition (Z300) accompanied with the adjustable internal stress. The contact angle (CA) value of ZnO film reduced from 95° to 68° was owning to the different grain microstructure accompanied by a change in size variation. In addition, the UV light with different irradiation powers could also be used to improve the hydrophilicity varied from hydrophobic status to superhydrophilic status due to the desirable surface characteristics of the photocatalytic action. In addition, the photocatalytic activity of ZnO film exhibited efficient photodegradation of methylene blue (MB) under UV irradiation, with a chemical reaction constant of 2.93×10-3 min−1. In this present work, we demonstrated that the CA value of the ZnO films not only caused from hydrophobic to hydrophilic status accompanied by a change in grain size combined with internal stress but also induced by the UV light irradiation combined with photocatalytic activity simultaneously. On the other hand, the enhanced surface plasmonic resonance could be observed that is due to couple electron and photon oscillations and can be generated at the interface between a flat, continuous Pt capping nanolayer. This designed structure could also be considered as a Pt electrode pattern onto ZnO (metal Pt/ ceramic ZnO) for multifunctional heterostructured sensors and devices in near future.

Recently, Troyan et al (2019 arXiv:1908.01534) and Kong et al (2019 arXiv:1909.10482) extended near-room-temperature superconductors family by new yttrium superhydride polymorphs, YH_n (n = 4,6,7,9), which exhibit superconducting transition temperatures in the range of T_c = 210-243 K at pressure of P = 160-255 GPa. In this paper, temperature dependent upper critical field data, B_c2(T), for highly-compressed mixture of YH₄+YH₆ phases (reported by Kong et al 2019 arXiv:1909.10482) is analysed to deduce the ratio of T_c to the Fermi temperature, T_F. Our analysis shows that in all considered scenarios the YH₄+YH₆ mixture has the ratio 0.01 ≤ T_c/T_F ≤ 0.04. As the result, YH₄+YH₆ falls in the unconventional superconductors band in the Uemura plot. It is also found that the characteristic temperature of the order parameter amplitude fluctuations, T_fluc, in the YH₄+YH₆ mixture is only several percent above observed T_c, and thus the superconducting transition in yttrium superhydride polymorphs is fundamentally limited by thermodynamics fluctuations.

Unmanned Aerial Systems (UAS) have rapidly gained attraction in recent years as a promising solution to revolutionize numerous applications and meet the growing demand for efficient and timely delivery services due to their highly automated operation framework. Beyond Visual Line of Sight (BVLOS) operations, in particular, offer new means of delivering added-value services through a wide range of applications. This ’plateau of productivity’ holds enormous promise but it is challenging to equip the drone with affordable technologies which support the BVLOS use-case. To close this gap, this work showcases the convergence of the automotive and aviation industries to advance BVLOS aviation for UAS in a practical setting by studying a combination of Commercial Off-The-Shelf (COTS) technologies and systems. A novel risk based approach of investigating the key technological components, architectures, algorithms and protocols is proposed, that facilitate highly reliable and autonomous BVLOS operations, aiming to enhance the alignment between market and operational needs and to better identify integration requirements between the different capabilities to be developed.

Patients in intensive care unit often lose a considerable fraction of their gut microbiome due to exposure of broad-spectrum antibiotics and other reasons. Dysbiosis often results in prolonged diarrhea and increase occurrence of multi-drug resistant pathogens in the colon with clinical consequences not yet well understood. Restoring the microbioma by faecal microbial transplantation (FMT) is a plausible therapeutic possibility, so far only documented in case reports and case series using very heterogeneous methodologies. Before FMT in critically ill can be tested in randomised controlled trials, there is a burning need to describe a standardized operating procedure (SOP) of the whole process, respecting the specifics of critically ill population, such as the risk of disrubted intestinal barrier and time critical nature of the procedure. We describe the SOP that has been developed for experimental use in critically ill patients by a multidisciplinary team of intensivists, gastroenterologist and microbiologist based on feedback from regulatory authority (State Institue of Drug Control of the Czech Republic). The hallmarks of these SOPs are multi-donor freshly frozen transplantate quaranteeded for 3 months consisting of 7 aliqutes from 7 unrelated healthy donors, and administered by rectal tube. In this paper we discuss the rationale for this SOP and the process of its development in details and release the full proposed SOP is in the form of online appendix.

Given the high levels of overall volume of alcohol use, detrimental drinking patterns, and high levels of alcohol-attributable mortality and burden of disease, Lithuania implemented a series of alcohol control policies within a relatively short period of time (2008 to 2019). Based on their expected impact on alcohol consumption and alcohol-attributable harm, as well as their target population, the respective policies were classified using a set of objective criteria and expert opin-ion. The classification criteria included: positive vs. negative outcomes, mainly immediate versus delayed outcomes, and general population versus specific group outcomes. The judgement of the alcohol policy experts converged on the objective criteria, and, as a result, two tiers of inter-vention were identified: Tier 1 – general population interventions with an anticipated immediate impact; Tier 2 – other interventions aimed at the general population. In addition, interventions for specific populations were identified. This adaptable methodological approach to alcohol control policy classification is intended to provide guidance and support the evaluation of alcohol policies elsewhere, lay the foundation for the critical assessment of the respective policies to im-prove health and increase life expectancy, and to reduce crime and violence.

The solid particle erosion at room and elevated temperatures of pure and filled hot-curing epoxy resin on anhydride hardener was experimentally tested using accelerated method on special bench. Micro-sized dispersed industrial wastes were used as fillers: fly-ash from a power plant and spent filling material from a copper mining and processing plant. The results showed that the unfilled resin wear significantly decreases with increasing temperature, while the dependence on the temperature of the wear intensity at an impingement angle of 45o is linear inversely proportional, and at an angle of 90o non-linear. The decrease in wear intensity is probably due to an increase in elasticity (an increase in the fracture strain limit) because of heating. Solid particle erosion of the examined filled epoxy compounds is considerably higher than that of unfilled compounds at impingement angles of 90o and 45o. Filled compounds showed ambiguous dependences of intensity of wear from temperature (especially at an angle of attack 45o), probably, character of dependence is defined by a filler share and the structural features of the samples caused by distribution of particles of the filler. Intensity of wear of the considered compounds at impingement angles 90o and 45o has high direct correlation with density and the modulus of elasticity (i.e., increases with their increase), and low correlation with bending strength of the considered materials. The data set for determining the correlation between mechanical properties and wear included characteristics due to both compound filling and test temperature.

Background: The commonly known assumption that combinations of several herbs in one formulation can have better efficacy due to additive or synergistic effects has not been systematically studied despite some evidence supporting the synergy concept. Study aim: The study aimed to reveal the molecular interactions in situ of host cells in response to the intervention of BHP and justify the benefits of implementing BHP in clinical practice. Results: This overview provides the results of recent clinical and network pharmacology studies of botanical herbal preparations (BHP) of Rhodiola with other plants, including Ashwagandha, Green Tea, Eleutherococcus, Schisandra, Eleutherococcus, Leuzea, Caffeine, Cordyceps, Gingko, Black Cohosh, saffron, and L-carnosine. Conclusions: The most important finding from network pharmacology studies of BHP was the evidence supporting the synergistic interaction of BHP ingredients, revealing unexpected new pharmacological activities unique and specific to the new BHP. Some studies show the superior efficacy of BHP compared with mono-drugs. At the same time, some a priori-designed combinations can fail, presumably due to antagonistic interactions and crosstalk between molecular targets within molecular networks involved in the cellular and overall response of organisms on the intervention. Network pharmacology studies help predict the results of studies to discover new indications and unpredicted adverse events.

In this paper, particular attention is paid to an advanced variant of the plug-in hybrid engine, known as PHEV, which combines two functionalities: the vehicle's internal combustion engine (ICEV) and the electric engine (BEV). The paper also presents the assumptions of the DEVS model, which allows for the estimation of vehicle’s energy consumption. The study described herein also presents the influence of factors such as ambient temperature and constant speed on the PHEV’s energy consumption. It has been shown that the vehicle’s range estimated based on its electronic control module (ECU) is about 20% shorter per annum on average for its year-round operation in every-day driving conditions. When analyzing the energy consumption based on the vehicle’s unit energy consumption model, attention was paid to values that are strongly correlated with the traffic volume and weather conditions affecting the moving vehicle. In addition, the authors emphasized that the estimated total energy consumption of an electric (BEV) or hybrid (PHEV) vehicle, relative to the normative values arising from the type approval test cycle, deviate from the actual values arising from real driving conditions and often vary substantially. In extreme cases, the actual range of a hybrid vehicle is 75% shorter.

We present atomic structures and nonequilbrium synthesis of new class of materials, where the basic structural unit is a diamond tetrahedron. When units of one, two, and three tetrahedra are randomly packed, we create distinct phases of amorphous Q-carbon. Four tetrahedra in two adjacent layers lead to crystalline diamond lattice, which has four missing tetrahedra alternately. When these four missing tetrahedra are filled, we create subunit cell of crystalline Q-diamond. Theoretical calculations show that superconducting transition temperature (Tc) in 50 atomic % B-doped Q-diamond can reach near room temperature at ambient pressures. This is consistent with our earlier results using low-loss EELS measurements in 50 atomic % B-doped Q-carbon, which had mostly amorphous QB3 phase mixed with some crystalline Q-diamond phase. These EELS results showed that the Tc for these samples was in between 90K and 300K. Theoretical calculations of density of states, Eliashberg function, electron-phonon interaction parameter, and root-mean-square and logarithmic average of frequency in crystalline Q-diamond show Tc in the range of 268K to 300K, which is in a complete agreement with our EELS results in QB3.

In this paper a novel type of a highly sensitive gas sensor device based on the surface photovoltage effect is described. The developed surface photovoltage gas sensor is based on a reverse Kelvin probe approach. As the active gas sensing electrode the porous ZnO nanostructured thin films are used deposited by the direct current (DC) reactive magnetron sputtering method exhibiting the nanocoral surface morphology combined with an evident surface nonstoichiometry related to the unintentional surface carbon and water vapor contaminations. Among others, the demonstrated SPV gas sensor device exhibits a high sensitivity of 1 ppm to NO₂ with a signal to noise ratio of about 50 and a fast response time of several seconds under the room temperature conditions.

Accidents at mining enterprises, including tailing dumps, pose significant threats to human lives, structures, and the environment. This study focuses on designing, constructing, and operating tailing dumps in Siberia's northern region. To ensure safety and minimize environmental impacts, comprehensive scientific monitoring and research were conducted at all stages, including design, construction, operation, and disposal. The aim was to create a uniform mass within the dam body, requiring understanding of the tailings' structure and technological characteristics during placement. Parameters like particle size, distribution, density, and moisture content were considered to assess tailings' physical and geometric properties. Estimated monitoring was introduced as a permanent model to quickly assess the stability of hydrotechnical constructions. This involved monitoring changes in exploitation properties, structure height, beach length, and water levels. A controlled inwashing technology for subsequent dam layers was developed. Complex research facilitated the formulation of an estimated monitoring methodology and an algorithm for tailing dam formation. Practical application demonstrated high reliability and confirmed load-bearing capacity, allowing for the forecast of dam stability and safe execution. Findings led to alterations in work techniques, ensuring safe and efficient operation of tailing dams.

The photoreduction of CO2 is an intriguing process, which allows the synthesis of fuels and chemicals. One of the limitations for CO2 photoreduction in the liquid phase is its low solubility in water. This point has been here addressed by designing a fully innovative concept of pressurized photoreactor, allowing operation up to 20 bar and applied to improve the productivity of this very challenging process. The photoreduction of CO2 in the liquid phase was performed using commercial TiO2 (Evonink P25), TiO2 obtained by flame spray pyrolysis (FSP) and gold doped P25 (0.2 wt% Au-P25) in the presence of Na2SO3 as hole scavenger (HS). The different reaction parameters (catalyst concentration, pH and amount of HS) have been addressed. The products in liquid phase were formic acid and formaldehyde. Moreover, for longer reaction time and with total consumption of HS, gas phase products formed (H2 and CO) after accumulation of significant amount of organic compounds in the liquid phase, due to their consecutive photoreforming. Enhanced CO2 solubility in water was achieved by adding a base (pH= 12-14). In basic environment, CO2 formed carbonates which further reduced to formaldehyde and formic acid and consequently formed CO/CO2+H2 in the gas phase through photoreforming. The deposition of small Au nanoparticles (3-5 nm) (NPs) onto TiO2 was found to quantitatively influence the products distribution and increase the selectivity towards gas phase products.

Abstract: The study used whole-genome sequencing (WGS) and bioinformatics analysis for the genomic characterization of 60 isolates of Listeria monocytogenes isolated from cattle farms, cattle abattoirs, and retail outlets in Gauteng province, South Africa. The isolates' sequence types (STs), clonal complexes (CCs), and lineages were determined using in silico multilocus sequence typing (MLST). We used BLAST-based analyses to identify virulence and antimicrobial genes, plasmids, proviruses, and the CRISPR-Cas system. The study investigated any association of the detected genes to the origin in the beef production chain of the L. monocytogenes isolates. Overall, in 60 isolates of Listeria monocytogenes, there were 7 STs, 6 CCs, 44 putative virulence factors, 2 resistance genes, 1 plasmid with AMR genes and 3 with conjugative genes, 1 CRISPR gene, and all 60 isolates were positive for proviruses. Among the 7 STs detected, ST204 (46.7%) and ST2 (21.7%) were the most prominent, with ST frequency varying significantly (p<0.001). The predominant CC detected were CC2 (21.7%) and CC204 (46.7%) in lineages I and II, respectively. Of the 44 virulence factors detected, 26 (across Listeria Pathogenicity Islands, LIPIs) were present in all the isolates. The difference in the detection frequency varied significantly (P<0.001). The two AMR genes (fosX and vga(G)) detected were present in all 60 (100%) isolates of L. monocytogenes. The only plasmid, NF033156, was present in 3 (5%) isolates. A CRISPR-Cas system was detected in 6 (10%), and all the isolates carried proviruses. Significant differences were detected in the frequencies of STs and virulence factors regarding the source and sample type of the L. monocytogenes isolates. The presence of both fosX and vga(G) genes in all the isolates from the three industries (cattle farms, abattoirs, and retail outlets) can potentially cause therapeutic implications. Our study, which characterized L. monocytogenes recovered from the three levels in the beef production chain in the country, provides the first evidence of the distribution of the pathogen with potential food safety and therapeutic implications.

Recent developments in the field of room temperature ferromagnetic metal oxide semiconductors (RTFMOS) have shown promising potential for improved photocatalytic performance. This review focuses on the combined study of photocatalytic and ferromagnetic properties at room temperature, with a particular emphasis on metal oxides, such as TiO2, which have emerged as a key area of interest in the domains of magnetism and environmental remediation. Despite extensive research over the years, the precise mechanism behind the interplay of ferromagnetism and photocatalysis in these materials remains incompletely understood. Several critical factors contributing to magnetism have been hinted at, including oxygen vacancies and various metal doping. Numerous reports have demonstrated that these factors play a primary role in room temperature ferromagnetism and photocatalysis in wide-band-gap metal oxides. However, establishing a direct correlation between magnetism, oxygen vacancies, dopant concentration, and photocatalysis has proven challenging. This review aims to provide a comprehensive overview of the recent progress in understanding the magnetism and photocatalytic behaviour of metal oxides. By examining the latest findings, this study sheds light on the potential of RTFMOS as effective photocatalysts, thereby contributing to advancements in environmental remediation and related applications.

A Zn(II) perchlorate complex has been prepared and characterized by single X-ray crystallography, nuclear magnetic resonance spectroscopy, thermogravimetric analysis, infrared spectroscopy, elemental analysis, and UV-vis spectroscopy. The complex crystallizes in the monoclinic space group P21/c (Z = 4) with a pentacoordinated zinc center. Interestingly, the Zn complex was found be to a potential fluorophore that could sense acetone and other ketones with high selectivity and sensitivity.

This paper proposes a circuit model of Cross-Coupled CMOS AC – DC Charge Pump (XC – CP) operating in subthreshold region. The aim is improving the efficiency to design XC – CPs with variety of specifications, e.g., input and output voltages and AC input frequency. First, it is shown that the output resistance (Ro) of XC – CP is much higher than those of CPs with single diodes (SD – CP) and ultra-low-power diodes (ULPD – CP) as charge transfer switches (CTSs). Second, the reason behind the above feature of XC – CP is identified by a simple model that the gate-to-source voltages of CTS MOSFETs are independent of the output voltage of the CP. Third, high but finite Ro of XC – CP is explainable with a more accurate model that includes the dependence of the saturation current of MOSFETs operating in subthreshold region on the drain-to-source voltage which is a function of the output voltage of CP. The model was in good agreement with measured and simulated results of XC – , SD – and ULPD – CPs fabricated in 250 nm CMOS.

The medical sector is of the utmost importance in every country for well-known reasons such as their economic development, national security, quality of life, and so on. Many researchers were dedicated to this topic, however, in Romania there are limited studies on this subject. One reason is that most of the businesses in this sector are individual enterprises or small family businesses. In our research paper we deploy several analysis methods to see the financial sustainability of companies operating in the medical industry. By analyzing a sample of 23931 companies and we have concluded that their performance has increase in the peak of the pandemic and that the financial stability is high. Our results are in line with other similar studies that were conducted in other regions.

This paper provides a review of the aerodynamic behavior of horizontal axis wind turbines operating in hazardous environmental conditions. Over the past decade, renewable energy use has accelerated due to global warming, depleting fossil fuel reserves, and stricter environmental regulations. Among renewable options, solar and wind energy have shown economic viability and global growth. Horizontal axis wind turbines offer promising solutions for sustainable energy demand. Since wind turbines operate in an open environment, their efficiency depends on environmental conditions. Hazard environmental conditions, such as icing, rainfall, hailstorm, dust or sand, insects’ collisions, increased humidity and sea spray, result in degraded aerodynamic performance. The outcome of the most studies is that lift is degraded and at the same time drag is increased when wind turbines operate under these conditions. The objective of this review is to improve our comprehension of the crucial aspects to take into account when designing wind turbine blades, and it offers suggestions for future research paths. It serves as a valuable resource that can inspire researchers who are dedicated to enhancing the aerodynamic performance of horizontal axis wind turbines.

In this paper, by developing a mathematical model, the operating temperature of perovskite solar cells (PSCs) under different operating conditions has been calculated. It is found that by reducing the density of tail states at the interfaces, acting as recombination centres, through some passivation mechanisms, the operating temperature can be reduced significantly at higher applied voltages. The results show that if the density of tail states at the interfaces is reduced by three orders of magnitude through some passivation mechanisms, then the active layer may not undergo any phase change up to an ambient temperature 300 K and it may not degrade up to 320 K. The calculated heat generation at the interfaces at different applied voltages with and without passivation shows that the heat generation can be reduced by passivating the interfaces. It is expected that this study may provide a deeper understanding of the influence of interface passivation on the operating temperature of PSCs.

Abstract: The recent growing attention to energy saving and environmental protection issues has brought to attention the possibility of exploiting syngas from gasification of biomass and coal for the firing of industrial plants included the so called Integrated Gasification Combined Cycle ones. In order to acquire a detailed knowledge about the behaviour of lean turbulent premixed flames, the present work resent the results of an experimental characterisation of a prototypical gas turbine burner operated at atmospheric pressure at condition scaled from real gas turbines ones. The results here presented derive from OH-PLIF measurements carried out at decreasing air equivalence ratio conditions and are analysed together with a mean aerodynamic characterisation of the burner operating in isothermal condition. The OH concentration distributions have been analysed statistically in order to obtain information about the location of the most reactive zones and an algorithm has been applied to the data sets in order to identify the flame fronts. In addition, the flame front locations have been successively interpreted statistically in order to obtain information about their main features and about their dependence on the air to fuel ratio behaviour.

The operation of transformers suffers from natural or man-made disasters, subjecting the equipment to prolonged exposure to temperature, lightning strikes, transient over-voltages, and over-current, gradually producing insulation aging phenomenon, which results in partial discharges within the transformer. Without dealing with it beforehand properly, it may lead to insulation breakdown. Nowadays, with the mature development of microchip control technology and wireless communication technology, which is helpful for realizing the research for online real-time and long-term monitoring capabilities for power equipment. A transformer operating condition monitoring and diagnostic system that can rapidly and effectively prevent the breakdown of transformer insulation, which can impact the overall power supply system is developed in this paper. The system is divided into two parts based on its function. The first part is the operating condition monitoring and real-time alert unit for the transformer, primarily composed of an embedded computing module, a sensor module, and a transmission module. Its work content is to capture real-time online partial discharge ultrasonic signals and high frequency current comparator pulse signals, and analyze and determine the condition of the internal insulation and operational status whether it is fault or not. The second part is the central control unit, consisting mainly of an industrial computer and a transmission module. Its work content is to store the ultrasonic and high frequency current comparator pulse signals from the transformer operation monitoring and real-time alert unit. It uses the software to eliminate signal noise and interference, and then utilizes artificial neural networks to identify the type of fault. In this paper, the research for the phenomenon of insulation degradation in transformer equipment aims to establish aging trend profiles through the dual malfunctioning alert and aging process analysis, as well as the long-term measurement of ultrasonic signals from partial discharges and high-frequency current comparator pulse signals. This approach provides crucial reference data and a foundation for disposable on-site measurement, assessing the phenomenon of insulation aging stages, defects and damage of the transformers effectively. It allows for timely replacement or maintenance in advance, achieving the prevention of malfunctioning and predictive diagnosis of aging.

Aseptic implant loosening after total joint replacement is partially influenced by material-specific factors when cobalt-chromium alloys are used, including osteolysis induced by wear- and corrosion products, and stress shielding. Here, we aim to characterize a hybrid material consisting of alumina-toughened zirconia ceramics (ATZ) and additively manufactured Ti-35Nb-6Ta (TiNbTa), joined by a glass solder. The structure of the joint, static and fatigue shear strength, the influence of accelerated aging, and the cytotoxicity using an elution assay with human osteoblasts is characterized. Furthermore, the biomechanical properties of functional demonstrators of a femoral component for total knee replacements are evaluated. TiNbTa-ATZ specimens showed a homogenous joint with statistical distributed micro-pores and a slight accumulation of Al-rich compounds at the glass solder-TiNbTa interface. The static shear strength was 26.4 ± 4.2 MPa (Ti-ATZ reference: 38.2 ± 14.4 MPa, p = 0.117), all specimens survived 107 cycles of shear loading to 10 MPa, and aging did not reduce the strength. TiNbTa-ATZ did not impair the proliferation and metabolic activity of human osteoblasts. Functional demonstrators of TiNbTa-ATZ provided a maximum bearable extension-flexion moment of 40.7 ± 2.2 Nm. Biomechanical and biological properties of TiNbTa-ATZ demonstrate potential application for endoprosthetic implants.

Hybrid forecasting methods have emerged as a solution surpassing the limitations of both statistical and deep learning approaches. While the first emphasize the significance of variables, they often produce worse forecasting results when compared to newer techniques. In contrast, deep learning models remain enigmatic "black boxes" in terms of interpretability, although achieving better results in forecasting. This article introduces the Comprehensive Cross-Correlation and Lagged Linear Regression Deep Learning (CCLR-DL) framework, designed to harness the best of both approaches, enhancing forecasting accuracy while retaining model interpretability through a feature selection process. CCLR-DL blens cross-correlation analysis, lagged multiple linear regression and granger's causality procedures with deep learning architectures based on LSTM. In a practical demonstration, CCLR-DL was applied to a real database of clinical visits associated to diagnoses in Catalonia, Spain (tracking a population of 6.3 million patients during 10 years). Predicting visits enables the healthcare managers to be ready for future demand shifts. Results demonstrate a consistent and substantial improvement over standalone statistical and deep learning methods when predicting healthcare demand. This hybrid approach not only showcases its efficacy but also offers a promising solution to the challenge of balancing predictive accuracy with model explicability. In this context, this work aims to design and validate a method for feature selection and forecasting of multivariate high dimensional time series datasets not only to improve prediction accuracy but also to model transparency by identifying a subset of variables that improve predictions and G-cause the target variable.

An innovative superconducting mechanism was developed based on a patented discovery of room temperature superconductivity in several thorium (Th) salts or compounds. The rationale behind this discovery is through the experimental results about the unique electrical and magnetic properties of these Th salts. Accordingly, this new superconducting mechanism for these Th salts was obtained through the analyses of the compounds’ molecular configurations and the packings of their relevant crystal structures. Owing to the distinctive properties of the Th compounds in this discovery, we further established a different electron pairing scheme as opposed to the pairing of the Cooper pairs. Compared to the long distance electron pairing of the Cooper pairs, the new electron pairing in our mechanism is constructed by two closely correlated electrons that reside on the same atomic orbital of the Th cation as an electron lone pair. In this new superconducting mechanism, the Th cation is sitting on a relevant crystallographic lattice arrangement or a network of the relevant Th compounds. This network is constructed by many Th cations along certain crystallographic lattice arrangement where each Th cation contains one electron lone pair. This network allows the electron lone pairs on the Th cations to be delocalized over the network, “in pair”, and thus, reveals the electron lone pair in presence in a long distance fashion. The closely correlated electron lone pairs hop on this network and thus, construct the supercurrent over the network. This explanation about the superconductivity laid the basis for our superconducting mechanism. All these conclusions came from the previous studies about these compounds that illustrated their unusual features of a coexistence of high electrical conductivity and diamagnetism. These electrical and magnetic properties fall in line with that of superconductors but, surprisingly, these Th compounds have such properties at the ambient condition, meaning under room temperature and atmosphere pressure. We expect that this mechanism may be appropriate to be utilized to other superconducting cases, either conventional or unconventional, and therefore, can be adapted to describe the superconducting phenomenon for other superconductors.

In Ref. [1] Snider et al reported room temperature superconductivity in carbonaceous sulfur hydride (CSH) under high pressure. Recently the data for the temperature dependent ac magnetic susceptibility shown in figures of Ref [1] have appeared in the form of tables corresponding to different pressures [2]. Here we provide an analysis of the data for a pressure of 160 GPa. This work was performed in collaboration with D. van der Marel.

This paper proposes the localisation of room occupants in home environments using Unobtrusive Sensing Solutions (USSs). The ability to localise room occupants in home environments can help in the objective monitoring of sedentary behaviour. While wearable sensors can provide tangible information on health and wellness, they have battery life issues and the inability to perform prolonged monitoring. This work uses heterogeneous USSs in the form of an Infrared Thermopile Array (ITA-64) thermal sensor and a Multi-Chirp Frequency Modulated Continuous Wave Mono-pulse (MC-FMCW-M) Radar sensor to monitor room occupants. Digital filters and background subtraction algorithms were used to process the thermal images gleaned from the ITA-64 thermal sensors. The MC-FMCW-M Radar sensor used multi-chirp and Doppler shift principles to estimate the exact location of the targeted room occupants. The estimated distances from the Radar Sensor were compared with ground truth values. Experimental results demonstrated the ability to identify thermal blobs of occupants present in the room at any particular time. Data analyses indicated no significant difference (p = 0.975) and a very strong positive correlation (r = 0.998) between the ground truth distance values and those obtained from the Radar Sensor.

A brief review of the history of the problem is intended to trace the progress in the development of scientific views on the structure of water. The discoveries in this area made in the first half of the last century are considered in comparison with modern data. It is shown that due to the de facto ban on the study of the structure of water in 1971, work in this direction was frozen for a long time. The paradox is that many forgotten truths have been independently "rediscovered" in our time, which speaks of their authenticity. On the basis of scientific literature and their own research, the authors come to the conclusion that water under room conditions is a microdispersed system, one phase of which is represented by continuous water, and the other - by polywater, discovered in the 70s of the last century.

Dye sensitized solar cell technology is having an important role in renewable energy research due to its features and low cost manufacturing processes. Devices based on this technology appear very well suited for integration into glazing systems due to their characteristics of transparency, color tuning and manufacturing directly on glass substrates. Field data of thermal and electrical characteristics of dye sensitized solar modules (DSM) are important since they can be used as input of building simulation models for the evaluation of their energy saving potential when integrated into buildings. However still few works in the literature provide this information. The study here presented wants to contribute to fill this gap providing a thermal and electrical characterization of a DSM in real operating conditions using a method developed in house. This method uses experimental data coming from test boxes exposed outdoor and dynamic simulation to provide thermal transmittance and solar heat gain coefficient (SHGC) of a DSM prototype. The device exhibits an U-value of 3.6 W/m²K, confirmed by an additional measurement carried on in the lab using a heat flux meter, and a SHGC of 0.2, value compliant with literature results. Electrical characterization evidences an increase of module power with respect to temperature causing DSM suitable for integration in building facades.

This study investigated the mechanical properties and fatigue behavior of FH36 steel plate rolled in different directions. By adopting a sequential rolling process in the rolling direction (RD) and transverse direction (TD), the differences in properties between RD and TD were eliminated, resulting in nearly identical tensile properties. The steel plate exhibited a yield strength of approximately 420 MPa, a tensile strength of approximately 506 MPa, and an elongation of approximately 25%. Fatigue tests conducted at room temperature and -60℃ showed a fatigue limit of the maximum stress of 488 MPa at room temperature and 500 MPa at -60℃, indicating improved low-temperature fatigue performance. The fracture surfaces displayed distinct characteristics, such as oblique shearing fractures for high-cycle fatigue and cup-cone shape fractures for low-cycle fatigue. The fatigue source zone were both on the surface of the specimens. As the maximum stress increased, the area of the crack propagation zone for high-cycle fatigue decreased, while the area of the final fracture zone, the number of dimples and the proportion of the LAGBs increased.

A labyrinth metamaterial wall with glass coverage is measured in a reverberating chamber and after its installation in a restaurant. Glass is used to meet two aims, namely acoustic absorption and visual design demands. The wall consists of five multiple labyrinth elements of 1.83 m$^2$ each. Glass was taken to make the wall act as a room lightning device where a translucent cover material is needed. Absorption measurements show about four times improved absorption compared to typical glass. Due to the metamaterial behavior, absorption is high in the low-frequency range below 300 Hz where damping is problematic with traditional materials. Especially in this range, the glass metamaterial wall is an excellent compromise between room acoustic and visual design demands, as loud low-frequencies make visitors speak louder and experience less intimacy with additionally reduced speech intelligibility. For mid-frequencies, absorption is shown less effective and improvements are discussed.

In ref. [1], we pointed out that certain anomalies observed in the published data for ac magnetic susceptibility of a room temperature superconductor reported in Nature 586, 373 (2020) [2] would be cleared up once the measured raw data were made available. Part of the measured raw data were recently posted in arXiv:2111.15017 [3]. Here we report the results of our analysis of these raw data and our conclusion that they are incompatible with the published data. Implications of these results to the claim that the material is a room temperature superconductor are discussed.

Room-temperature phosphorescent (RTP) materials have been attracted tremendous interest owing to their unique material characteristics and potential applications for state-of-the-art optoelectronic devices. Recently, we have reported a synthesis and fundamental photophysical properties of new RTP materials based on benzil, i.e., fluorinated monobenzil derivative and fluorinated and non-fluorinated bisbenzil derivative analogues [Yamada, S. et al, Beilstein J. Org. Chem. 2020, 16, 1154–1162.]. To further understand their RTP properties, here we investigated the excited-state dynamics and photostability of the derivatives by means of time-resolved and steady-state photoluminescence spectroscopies. For these derivatives, clear RTP emissions with lifetimes on the microsecond timescale were identified. Among them, the monobenzil derivative was found to be the most efficient RTP material, showing both the longest lifetime and highest amplitude RTP emission. Time-resolved photoluminescence spectra measured at 77 K and density functional theory calculations revealed the existence of a second excited triplet state in the vicinity of the first excited singlet state for the monobenzil derivative, indicative of the presence of a fast intersystem crossing pathway. A discussion of the correlation between the excited state dynamics, emission properties, and conformational flexibility of the three derivatives is presented.

In this study, we address the formidable challenge of solving large-scale Max-Cut problems (MCP). We introduce a rapid computational procedure utilizing a hybrid 1-flip/r-flip local search heuristic. This innovative strategy significantly reduces the computational time required for MCP problems while consistently generating solutions of exceptional quality. The paper presents substantial computational insights, showcasing the effectiveness of our approach on very-large-scale Max-Cut instances with varying densities. Our proposed heuristic is rigorously evaluated by comparing its performance against a quantum annealing solver, leveraging a multi-start Tabu Search framework. The results underscore the potency of this unique combination as an efficient and effective solution for large-scale QUBO problems. Notably, our hybrid heuristic consistently delivers high-quality solutions within the stringent CPU time limits of 600 seconds, demonstrating its efficacy across Max-Cut instances ranging from 10,000 to 40,000 variables. This research contributes to advancing the state-of-the-art in large-scale QUBO problem-solving, offering a powerful and time-efficient approach with broad applicability.

In large industrial plants, the trend is to move the position of the human to the area of service and diagnostics, in medium and smaller plants the trend is different and is mainly directed to the sphere of close cooperation between the human and the robotic system. This paper deals with the implementation of human-cooperating robots in manufacturing processes. The analytical part of the paper deals with theoretical knowledge, taking into account the latest trends in the subject area. To achieve a successful implementation of cobots based on the above-mentioned operating systems in manufacturing systems, it is necessary to pay attention specifically to the interfacing of the robotic operating system with the control systems of the manufacturing systems at the process level of the enterprise. Within the practical part, an algorithm with well-defined steps towards the successful implementation of cobots in holonic manufacturing processes is proposed. By setting up an experimental workstation in the laboratory, the proposed procedures are verified at the end of the paper. In the context of the implementation of collaborative robots in enterprises, the paper also discusses cloud computing. The creation of a design for the implementation of a collaborative robot with a human represents the missing link in the whole chain of commercial applications of the latest trends from the field of robotic systems in the industrial sphere.

South Korea proposed reducing greenhouse gas emissions by 37% compared to the expected emissions by 2030 as the POST-2020 greenhouse gas reduction target. Electric vehicle distribution in the public sector is essential to achieve the carbon dioxide reduction target for transportation. In particular, when buses with internal combustion engines, which travel long distances and contribute substantially to greenhouse gas emissions, are replaced with electric buses, it is expected that greenhouse gas emissions will be significantly reduced. There are three types of electric buses with different power supply systems: a plug-in type in which power is supplied when a plug is inserted, a battery-swapping type in which a battery mounted on top of the vehicle is swapped at a swapping station, and a wireless type in which the battery is wirelessly charged through self-induction at a charging facility installed on the road. Vehicles of each charging type have different advantages and disadvantages. The performance, charging type, battery capacity, and operating environment of electric buses are mutually related parameters that must be considered when introducing such vehicles. Therefore, the optimal charging type must be selected according to the operating environment to enable the widespread use of electric buses. As such, this report proposes the optimal charging type according to the operating environment of public-sector electric vehicles.

Information encryption and anti-counterfeiting play an important role in many aspects of daily life, such as in minimizing economic losses, protecting secure communication and public security, and so on. Owing to the high information capacity and ease of operation, luminescent materials for advanced information encryption and anti-counterfeiting are essential to meet the increasing demand on encryption security. Herein, we summarize two emerging luminescent materials for information encryption and anti-counterfeiting, the AIE materials and room-temperature phosphorescent materials. At last, we discuss the opportunities and anticipations of these two information encryption and anti-counterfeiting materials.

Escape room’s games are educational gamification technologies that consist of introducing a team of players into a physical or digital space to solve a mystery or a problem in search of clues to solve puzzles, riddles, or enigmas. This study aims to determine the effectiveness of escape room’s games on the training of nurses and nursing students. A systematic review was carried out in MEDLINE, WOS, SCOPUS, CINAHL and LILACS databases using the MeSH terms: "Education, Nursing" and "Educational Technology", and the free term "Escape room", combining with Boolean operators AND/OR. Intervention studies in Spanish, English and Portuguese were included, without limitation for the year of publication. Selection and critical appraisal were conducted by two independent reviewers. A total of n=15 interventional studies were included (n=2 Randomized Clinical Trials and n=12 quasi-experimental). Escape rooms are a recent and booming educational methodology, which is increasingly used in academia and training of nurses and nursing students; however, it is necessary to expand their use to more countries, as well as the number and quality of interventional studies, being necessary to homogenize and standardize criteria and to use validated instruments to evaluate the effectiveness of escape rooms in the field of nursing.

ZnO thin films with a thickness of 300 nm were deposited on Si and Al2O3 substrates using electron beam evaporation technique with the aim to be tested as low cost and low power consumption gas sensors for ozone (O3). To characterize the surface roughness and the grain size, which are the main parameters recognized to enhance gas sensitivity since they directly influence the effective sensing area, surface morphology and roughness analyses of the films were performed using scanning electron microscopy and atomic force microscopy, respectively. The crystalline structure and elemental composition were studied through Raman spectroscopy and X-ray photoelectron spectroscopy. Gas tests were conducted at room temperature and zero-bias voltage to assess the sensitivity and response as a function of time of the films to O3 pollutant. The results indicate that the films deposited on Al2O3 exhibit promising characteristics, such as high sensitivity and a very short response time (< 2 s) to the gas concentration. Additionally, it was observed that the films display pronounced degradation effects after a significant exposure to O3.

Base on building information modeling(BIM) plus with Robotic process automation (RPA) technology is rapid development in smart building operations and maintenance (O&M). RPA is a workflow-based automated execution tool that is particularly well suited for replacing manual execution of simple and repetitive tasks using computer systems. The use of RPA technology can saves man-hours and increases productivity, which is important for the automation of building operations and maintenance operations.. The BIM technology, as an advanced technology in the construction industry, it can provide new ideas and methods for building operation and maintenance based on its visualization characteristics. That’s integrating RPA with BIM technology which will enhance the digitalization and virtualization of smart building operation and management. In this article will first introduce the features of RPA and BIM technology and then discuss the technical roadmap for remote automated operation and maintenance of smart building equipment room to implemention a low-cost and high efficient building equipment room operation and maintenance solution.

Energy storage systems play a crucial role in the overall performance of hybrid electric vehicles. Therefore, the state of the art in energy storage systems for hybrid electric vehicles has been discussed in this paper along with appropriate background information for facilitating future research in this domain. Specifically, we have compared the key parameters such as cost, power density, energy density, cycle life, and response time for various energy storage systems. For the energy storage systems employing ultra capacitors, we have presented the characteristics such as cell voltage, cycle life, power density and energy density. Furthermore, we have discussed and evaluated the interconnection topologies for the existing energy storage systems. We have also discussed the hybrid battery-flywheel energy storage system as well as the mathematical modeling of the battery-ultracapacitor energy storage system. Toward the end, we have discussed energy efficient powertrain for hybrid electric vehicles.

By utilizing a generalized version of the Madelung quantum-hydrodynamic framework that incorporates noise, we derive a solution using the path integral method to investigate how a quantum superposition of states evolves over time. This exploration seeks to comprehend the process through which a stable quantum state ultimately emerges in the presence of fluctuations induced by the noisy gravitational background. The model defines the conditions that give rise to a limited range of interaction for the quantum potential, allowing for the existence of coarse-grained classical descriptions at a macroscopic level. The theory uncovers the smallest attainable level of uncertainty in an open quantum system and examines its consistency with the localized behavior observed in large-scale classical systems. The research delves into connections and similarities with decoherence theory and the Copenhagen interpretation of quantum mechanics. Additionally, it assesses the potential consequences of wave function decay on the measurement of photon entanglement. To validate the proposed theory, an experiment involving entangled photons transmitted between detectors on the Moon and Mars is discussed. Finally, the findings of the theory are applied to the creation of larger Q-bits systems at elevated temperatures.

An advanced driver-assistance system (ADAS) is critical to driver-vehicle-interaction systems. Driving behaviour modelling and control significantly improves the global performance of ADAS. A haptic assistive system assists the driver by providing a specific torque on the steering wheel according to the driving-vehicle-road profile to improve the steering control. However, the main problem is designing a compensator dealing with the high-level uncertainties in different driving scenarios with haptic driver assistance, where different personalities and diverse perceptions of drivers are considered. If not properly accounted for, these differences can lead to poor driving performance. This paper focuses on designing a data-driven model-free compensator considering various driving behaviours with a haptic feedback system. A back propagation neural network (BPNN) models driving behaviour based on real driving data (speed, acceleration, vehicle orientation, and current steering angle). Then using the genetic algorithm (GA) and the integral time absolute error (ITEA) criterion to optimize multiple PID compensation parameters for various driving behaviour (such as speeding/braking, lane-keeping and turning), which are then be combined by the fuzzy logic to provide different driving commands. An experiment was conducted with 5 participants in a driving simulator. During the second experiment, seven participants drove in the simulator to evaluate the robustness of the proposed combined GA-PID offline and the Fuzzy-PID controller applied online. The experiment results evaluated the ITAE of lateral displacement and yaw angle, during various driving behaviour. The results validated the proposed method by significantly enhancing the driving performance.

The recent growing attention to energy saving and environmental protection issues has brought to attention the possibility of exploiting syngas from gasification of biomass and coal for the firing of industrial plants included the so called Integrated Gasification Combined Cycle ones. In order to improve the knowledge about the employ of syngas in lean premixed turbulent flames, a large scale swirl stabilized gas-turbine burner has been operated with a simplified model of H₂ enriched syngas from coal gasification. The experimental campaign has been performed at atmospheric pressure with operating conditions derived from scaling the real gas turbines ones. The results are here reported and consist of OH-PLIF measurements carried out at decreasing air equivalence ratio conditions and are analysed together with the mean aerodynamic characterisation of the burner flowfield in isothermal condition. The OH concentration distributions have been analysed statistically in order to obtain information about the location of the most reactive zones and an algorithm has been applied to the data in order to identify the flame fronts. In addition, the flame front locations have been successively interpreted statistically in order to obtain information about their main features and about their dependence on the air to fuel ratio behaviour.