We aimed to investigate the relationship between membrane material and development of membrane fouling in a membrane bioreactor (MBR) using membranes with different pore sizes and hydrophilicities. Batch filtration tests were performed using submerged single hollow fiber membrane ultrafiltration (UF) modules with different polymeric membrane materials including cellulose acetate (CA), polyethersulfone (PES), and polyvinylidene fluoride (PVDF) with activated sludge taken from a municipal wastewater treatment plant. The three UF hollow fiber membranes were prepared by a non-solvent-induced phase separation method and had similar water permeabilities and pore sizes. The results revealed that transmembrane pressure (TMP) increased more sharply for the hydrophobic PVDF membrane than for the hydrophilic CA membrane in batch filtration tests, even when membranes with similar permeabilities and pore sizes were used. PVDF hollow fiber membranes with smaller pores had greater fouling propensity than those with larger pores. In contrast, CA hollow fiber membranes showed good mitigation of membrane fouling regardless of pore size. The results obtained in this study suggest that the surface hydrophilicity and pore size of UF membranes clearly affect the fouling properties in MBR operation when using activated sludge.

Contamination in coastal regions attributed to fluoride and nitrate cannot be disregarded, given the substantial environmental and public health issues they present worldwide. Maintaining water quality is crucial for environmental well-being. This comprehensive study was performed to assess the spatial as well as indexical water quality, identify contamination sources, and evaluate associated health risks pertaining to nitrate and flouride in AlHassa region, KSA. The physiochemical results revealed a pervasive pollution of the overall groundwater. The dominant water type was Na-Cl, indicating saltwater intrusion and reverse ion exchange impact. Spatiotemporal variations in physicochemical properties suggest diverse hydrochemical mechanisms, with geogenic factors primarily influencing groundwater chemistry. The groundwater pollution index varied between 0.8426 and 4.7172, classifying samples as moderately to very highly polluted. Similarly, the synthetic pollution index (in the range of 0.5021-4.0715) revealed that none of the samples had excellent water quality, with various degrees of pollution categories. Nitrate Health Quotient (HQ) values indicated chronic human health risks ranging from low to severe, with newborns being the most vulnerable. Household use of nitrate-rich groundwater for showering and cleaning did not pose significant health risks. Fluoride HQ decreased with age, and children faced the highest risk of fluorosis. The Hazard Index (HI) yielded moderate to high-risk values. Nitrate risks were 1.21 times higher than fluoride risks, as per average HI assessment. All samples fell into the vulnerable category based on the Total Hazard Index (THI), with 88.89% classified as very high risk. This research provides valuable insights into groundwater quality, guiding water authorities, inhabitants, and researchers in identifying safe water sources and vulnerable human populations. The results highlight the need for appropriate treatment techniques and long-term coastal groundwater management plans.

In the era of mounting water scarcity, particularly in arid regions, the agricultural sector is striving to optimize the water resource management practices. Treated wastewater (TWW) has emerged as a viable alternative to freshwater for irrigation, offering a sustainable solution to water conservation. However, ensuring the safety and quality of TWW is paramount to safeguard for both crop health and environmental integrity. Electrical conductivity (EC), a critical factor in assessing TWW suitability for irrigation, can significantly impact crop yields and soil health since it is directly linked to the concentration of dissolved salts and ions. Therefore, this study delves into the development of advanced predictive models for EC assessment by employing supervised machine learning (ML) techniques like the Support Vector Regression (SVR), Adaptive Network-based Fuzzy Inference System (ANFIS), and Multiple Linear Regression (MLR). The TWW samples collected from Al-Qatif area, Saudi Arabia were assessed in the lab through a sensor-based real-time monitoring system integrated with Internet of Things (IoT) network and a multiprobe device. The key water quality parameters assessed involved, temperature (T), pH, Oxidation Reduction Potential (ORP), Resistivity (RES), Total Dissolved Solids (TDS), Salinity and Turbidity which served as the foundation for these models, given their profound influence on and their anticipated impact on EC levels. Following feature selection, two distinct model combinations were identified for the SVR, ANFIS and MLR models. Furthermore, to evaluate prediction performance, four statistical criteria, including coefficient of determination (R²), correlation coefficient (R), mean square error (MSE), and root mean square error (RMSE), were employed. Overall, the comparative performance results proved that ANFIS-M2 indicated the strongest predictive capability with the R² value of 0.99572 and 0.75145 and the RMSE values of 0.00965 and 0.01134, respectively in both calibration and verification stages.

Citrus waste has been used as a source of bioplastic research in different ways. Because the juice industry produces significant amounts of residue each year, it would be advantageous to use the byproducts in the creation of new materials. For many years, researchers have been investigating an environmentally friendly way to take citrus and other organic waste and turn it into polymers that may be used, for instance, to produce bio-based and biodegradable films for food packaging. The goal of this study is to create biofilms from orange (OW) and ginger waste (GW) using an ultrafine grinder and study the films' properties. Since pectin has the ability to gel and because cellulosic fibres are strong, citrus waste has been studied for its potential to produce biofilms. After being washed, dried, and milled, orange and ginger waste were shaped into films using a casting process. Tensile testing was used to determine the mechanical properties of biofilms, while dynamic mechanical thermal analysis (DMTA), thermogravimetric analysis (TGA), and differential scanning calorimetry (DSC) were used to determine their thermal properties. As the number of grinding cycles increased, the suspension's viscosity increased from 29 to 57 mPa.s for OW and from 217 to 376 mPa.s for GW while the particle size in the suspension significantly decreased. For OW and GW films, the highest tensile strength was 17 MPa and 15 MPa, respectively. The maximum strain obtained among all films was 4.8%. All the tested films were stable up to 150°C, and maximum degradation occurs after 300°C.

Fouling represents a bottleneck problem for promoting the use of membranes in filtration and separation applications. It becomes even more persistent when it comes to the filtration of fluid emulsions. In this case, a gel-like layer that combines droplets, impurities, salts, and other materials form at the membrane's surface, blocking its pores. It is, therefore, a privilege to combat fouling by minimizing the accumulation of these droplets that work as seeds for other incoming droplets to cluster and coalesce with. In this work, we explore the use of the newly developed and novel periodic feed pressure technique (PFPT) in combating the fouling of ceramic membranes upon the filtration of oily water systems. The PFPT is based on alternating the applied transmembrane pressure (TMP) between the operating one and zero. A PFPT cycle is composed of a filtration half-cycle and a cleaning half-cycle. Permeation occurs when the TMP is set at its working value, while the cleaning occurs when it is zero. Three PFPT patterns were examined over two feeds of oily water systems with oil contents of 100 and 200ppm, respectively. The results show that the PFPT is very effective in minimizing the problem of fouling compared to a non-PFPT normal filtration. Furthermore, the overall drops in permeate flux during the cleaning half cycles are compensated by appreciable enhancement due to the significant elimination of fouling development such that the overall production of filtered water is even increased. Inspection of the internal surface of the membrane post rinsing at the end of the experiment proves that all PFPT cycles maintained the ceramic membranes as clean after a 2-hours operation. This can ensure a prolonged lifespan of the ceramic membrane use and a continuous greater permeate volume production. The advantage of the PFPT is that it can be implemented on existing units with minimal modification, ease of operation, and saving energy.

In this study, the hybrid biological ion exchange (BIEX) resin and gravity-driven membrane (GDM) process was employed for the treatment of coloured and turbid river water. The primary objective was to investigate the impact of both physical and chemical cleaning methods on ceramic and polymeric membranes in terms of stabilised flux, flux recovery after physical/chemical cleaning, and permeate quality. To address these objectives, two types of MF and UF membranes were utilised (M1 = polymeric MF, M2 = polymeric UF, M3 = ceramic UF, and M4 = lab-made ceramic MF).Throughout extended operation, the resin functioned initially in the primary ion exchange (IEX) region (NOM displacement with pre-charged chloride) and progressed to a secondary IEX stage (NOM displacement with bicarbonate and sulphate), while membrane flux remained stable. Subsequently, physical cleaning involved air/water backwash with two different flows and pressures, and chemical cleaning utilised NaOH at concentrations of 20 and 40 mM, as well as NaOCl at concentrations of 250 and 500 mg Cl2/L. These processes were carried out to assess flux recovery and identify fouling reversibility. The results indicated an endpoint of 1,728 bed volumes (BV) for the primary IEX region, while the secondary IEX continued up to 6,528 BV. At the end of the operation, DOC and UVA254 removal in the effluent of the BIEX columns were 68% and 81%, respectively, compared to influent water. This was followed by 30% and 57% DOC and UVA254 removal by M4 (ceramic MF). The stabilised flux remained approximately 3.8 – 5.2 LMH both before and after the cleaning process, suggesting that membrane materials do not play a pivotal role. The mean stabilised flux of polymeric membranes increased after cleaning, whereas that of ceramics decreased. Enhanced air–water backwash flow and pressure resulted in increased removal of hydraulic reversible fouling, which was identified as the dominant fouling type. Ceramic membranes exhibited higher removal of reversible hydraulic fouling than polymeric membranes. Chemical cleaning had a low impact on flux recovery; therefore, we recommend solely employing physical cleaning.

Controlling surface-protein interaction during wastewater treatment is the key motivation for developing functionally modified membranes. A new biocatalytic thermo-responsive poly(vinylidene fluoride)(PVDF)/nylon-6,6/poly(N-isopropylacrylamide)(PNIPAAm) ultrafiltration membrane was fabricated to achieve dual functionality of protein-digestion and thermo-responsive self-cleaning. The PVDF/nylon-6,6/PNIPAAm composite membranes were constructed by integrating a hydrophobic PVDF cast layer and hydrophilic nylon-6,6/PNIPAAm nanofiber layer where trypsin enzymes were covalently immobilized. The immobilization density of enzymes on the membrane surface decreased with increasing PNIPAAm concentration, due to the decreased number of amine functional sites. Through a ultrafiltration study using a model solution containing BSA/NaCl/CaCl₂, the PNIPAAm containing biocatalytic membranes demonstrated a combined effect of enzymatic and thermo-switchable self-cleaning. The membrane without PNIPAAm revealed superior fouling resistance and self-cleaning with an R_PD of 22%, compared to membranes with 2 and 4 wt% PNIPAAm with 26% and 33% R_PD, respectively, after an intermediate temperature cleaning at 50°C, indicating that higher enzyme density offers more efficient self-cleaning than the combined effect of enzyme and PNIPAAm at low concentration. The conformational volume phase transition of PNIPAAm did not affect the stability of immobilized trypsin on membrane surface. Such novel surface engineering design offer a promising route to severe surface-protein contamination remediation in food and wastewater applications.

Nanofibres have gained increasing attention due to their advantages of having a high porous structure, narrow pore size and distribution, and a high specific surface area. One of the most efficient techniques for producing nanofibres is via electrospinning. Nanofibres are currently being used in various fields, including water filtration. Although nanofibres possess the ability to filter various components, the fibres generally have a low mechanical strength that can mitigate the performance over time. Therefore, in overcoming this issue, several studies have focused on improving the strength of the nanofibre membranes for a water filtration application. This review discusses the advantages and challenges of nanofibres for water filtration membranes and summarises the methods to increase the strength of the membranes, including solvent vapour, thermal treatment, and chemical crosslinking.

The major challenge for membrane distillation (MD) is membrane wetting resistance induced by pollutants in the feed solution. The proposed solution for this issue was to fabricate membranes with hydrophobic properties. Hydrophobic electrospun Poly (vinylidene fluoride-co-hexafluoropropylene) (PVDF-HFP) nanofibers membranes were produced for brine treatment using the direct contact membrane distillation (DCMD) technique. These nanofibers membranes were prepared from three different polymeric solution compositions to study the effect of solvent composition in the electrospinning process. Further, the effect of the polymer concentration was investigated by preparing polymeric solutions with three different polymer percentages: 6, 8, and 10%. All nanofibers membranes obtained from electrospinning were post-treated at varying temperatures. The effects of thickness, porosity, pore size, and LEP were studied. The hydrophobicity was determined by contact angle measurements, which were investigated by optical contact angle goniometry. The crystallinity and thermal properties were studied by DCS and XRD, while the functional groups were studied by FTIR. The morphological study was performed by AMF and described the roughness of nanofibers membranes. Finally, all nanofibers membranes have enough of a hydrophobic nature to be used in DCMD. PVDF membrane filter disc and all nanofibers membranes were applied in DCMD to treat brine water. The resulting water flux and permeate water quality were compared, and it was discovered that all produced nanofibers membranes showed good behavior with varying water flux, but the salt rejection was greater than 90%. A membrane prepared from DMF/acetone 5-5 with 10% PVDF-HFP provided perfect performance, with an average water flux of 44 kg.m-2.h-1 and salt rejection of 99.8%.

In this study is reported the optical, structural and dielectric properties of Poly (vinyl alcohol) thin films membranes with embedded ZnO nanoparticles (PVA/ZnO) obtained by solution casting method at low temperature of deposition. Fourier Transform Infrared spectra showed the characteristics peaks, which correspond to O-H and Zn-O bonds present in the hybrid material. The X-ray diffraction patterns indicated the presence of ZnO structure into the films. The composite material showed low absorbance and a wide band gap energy from 5.6 to 5.9 eV. The surface morphology for the thin films of PVA/ZnO was studied by Atomic Force Microscopy and Scanning Electron Microscopy. The dielectric properties of the nanocomposites were measured from low to high frequencies, the results showed a high dielectric constant (ε) in the order of 10⁴ at low frequency and values from ε ≈ 2000 to 100 in the range of 1KHz-1MHz respectively, the properties of PVA/ZnO such as the high permittivity and the low temperature of processing make it a suitable material for potential applications in the development of flexible electronic devices.

in order to enhance the separation performance and to reduce the heat loss of the transmembrane for membrane distillation, the thermal efficiency and hydrophobicity of the membrane distillation should be simultaneously enhanced. In this work, a PVDF/PET hydrophobic/hydrophilic membrane is prepared by non-solvent phase inducing method. Nanosized silica aerogel (SiAG) with high porosity is added to the composite membranes. The modifying effects and operating conditions on permeate flux and thermal efficiency in direct contact membrane distillation (DCMD) are investigated. Furthermore, the latent heat of vaporization and the heat transfer across the membranes are compared for SiAG addition, which indicates that the composite PVDF@SiAG/PET membranes display a great potential for distillation-separation application with high heat efficiency.

Biomass and biowaste valorisation is of major interest nowadays because of the spirit of circular economy and of the neutral environmental fingerprint global target. In the current project chondroitin sulphate (ChS) was incorporated with the crustaceous’ and shrimp’s byproduct chitosan (Chi) and the fish industry byproduct gelatine (FG) to obtain dense hydrogel membranes. Glycerol (Gly) was utilized to avoid brittleness. The formation of the hydrogel membranes is attributed to secondary interactions between the natural polymers and the plasticizer. The prepared hydrogel membranes were characterized by Attenuated total reflectance-Fourier transform infrared spectroscopy (ATR-FTIR), X-ray diffraction (XRD) and thermogravimetric analysis (TGA). The surface morphology of the membranes was examined using scanning electron microscopy (SEM). Dynamic mechanical analysis (DMA) and tensile tests were also performed to evaluate the mechanical response of the membranes. The samples were also evaluated for membrane wettability, degradation rate and water vapor transmission rate (WVTR). Finally, in vitro endothelial cell attachment on the membrane were addressed. The overall results of the study indicate that the hydrogel membranes could be appropriate for external application in wound healing applications as dressings.

The permeability of the oral or nasal mucosa is higher than that of the skin. Mucosa permeability depends mainly on the thickness and keratinization degree of the tissues. Their permeability barrier is conditioned by the presence of certain lipids. This work has the main aim of reinforcing the barrier effect of oral mucosa with a series of formulations. Sixty-three initial formulations were evaluated for transmembrane water loss, with 16 formulations selected to test on sublingual mucosa. In vitro release tests of caffeine, ibuprofen, dexamethasone and ivermectin were carried out on porcine skin, mucosa and modified mucosa in order to compare the effectiveness of the formulations. A similar permeation profile was obtained in the different membranes: caffeine > ibuprofen ~ dexamethasone > ivermectin. The most efficient formulation was a liposomal formulation composed of lipids that are present in the skin stratum corneum. Impermeability provided by this formulation was really notable mainly for the low molecular weight compounds, decreasing their permeability coefficient between 40-80%. The reinforcement of the barrier function of mucosa provides a reduction or prevention of the permeation of different actives such as viruses, contaminants, toxins, etc.

Lipid composition in the cellular membranes plays an important role in maintaining the struc-tural integrity of cells and in regulating cellular signaling that controls functions of both mem-brane-anchored and cytoplasmic proteins. ATP-dependent ABC and P4-ATPase lipid transport-ers, two integral membrane proteins, are known to contribute to lipid translocation across the li-pid bilayers on the cellular membranes. In this review, we will highlight current knowledge about the role of cholesterol and phospholipids of cellular membrane in regulating cell signaling and how lipid transporters participate this process.

The analysis and simulation of water quality in distribution networks is a complex issue of great concern today. The analysis of the evolution of water age, as a simple indicator of water quality in the network, is of great interest in both design and operation phases. Understanding the factors that have the strongest influence on water quality is key to developing adequate strategies aimed at preserving it. This paper firstly analyses the factors with biggest influence in the tanks water age, to support the selection of the most appropriate configuration from the point of view of water quality during design phases. Then, the main considerations when modelling tanks following the different mixing models considered in Epanet have been presented. Also, a real tank behaviour has been characterised through field measurements and Epanet simulations in order to determine the best fitted mixing model.

Aβ peptides are known to bind neural plasma membranes in a process leading to the deposit of Aβ-enriched plaques. These extracellular structures are characteristic of Alzheimer’s disease, the major cause of late-age dementia. The mechanisms of Aβ plaque formation and deposition are far from being understood. A vast amount of literature describes the efforts to analyze those mechanisms, using a variety of tools. The present review focuses on biophysical studies, mostly carried out with model membranes, or with computational tools. The review starts by describing basic physical aspects of lipid phases, and commonly used model membranes (monolayers and bilayers). This is followed by a discussion of biophysical techniques applied to these systems, mainly but not exclusively Langmuir monolayers, isothermal calorimetry, density-gradient ultracentrifugation, and molecular dynamics. The methodological section is followed by the core of the review, a summary of important results obtained with each technique. The last section is devoted to an overall reflection and an effort in understanding Aβ-bilayer binding. Concepts such as Aβ peptide membrane binding, adsorption, and insertion are defined and differentiated. The roles of membrane lipid order, nanodomain formation, and electrostatic forces in Aβ-membrane interaction are separately identified and discussed.

Yttria stabilized zirconia materials are frequently used in mechanical engineering and biomedical applications. Demanding loading conditions require materials combining a high level of strength and fracture toughness. A ready to press alumina doped 2 mol% yttria stabilized zirconia powder was shaped by axial pressing and sintering in air at 1250 - 1500 °C for 2 h. The best combination of strength and toughness value of 7.8 MPa√m. Materials sintered in the middle of the chosen temperature range combine fully density, high transformability and small grain size. Toughness measurements by direct crack length measurements delivered unrealistically high fracture toughness values.

To investigate the effect of Polyvinylpyrrolidone (PVP) addition and consequently porosity, two different sets of membranes are manufactured, since PVP is a widely used poring agent which has an impact on the mechanical properties of the membrane material. The first set (PAN 1) includes PAN and the necessary solvent while the second set (PAN 2) is made of PAN and PVP. These membranes are put through several characterisation processes including tensile testing. The obtained data are used to model the static behaviour of the membranes with different geometries, but similar loading and boundary conditions that represent their operating conditions. This modelling process is undertaken by using finite element method. The main idea is to investigate how geometry affects the load-carrying capacity of the membranes. Alongside membrane modelling, their materials are modelled with representative elements with hexagonal and rectangular pore arrays (RE) to understand the impact of porosity on the mechanical properties. Exploring the results, the best geometry is found as the elliptic membrane with the aspect ratio 4 and the better RE as the hexagonal array which can predict the elastic properties with an approximate error of 12%.

Membrane remodeling and phospholipid biosynthesis are normally tightly regulated to maintain the shape and function of cells. Indeed, different physiological mechanisms ensure a precise coordination between de novo phospholipid biosynthesis and modulation of membrane morphology. Interestingly, the overproduction of certain membrane proteins hijack these regulation networks, leading to the formation of impressive intracellular membrane structures in both prokaryotic and eukaryotic cells. The proteins triggering an abnormal accumulation of membrane structures inside the cells (or membrane proliferation) share two major common features: 1) they promote the formation of highly curved membrane domains and 2) they lead to an enrichment in anionic, cone-shaped phospholipids (cardiolipin or phosphatidic acid) in the newly formed membranes. Taking into account the available examples of membrane proliferation upon protein overproduction, together with the latest biochemical, biophysical and structural data, we explore the relationship between protein synthesis and membrane biogenesis. We propose a mechanism for the formation of these non-physiological intracellular membranes that shares similarities with natural inner membrane structures found in α-proteobacteria, mitochondria and some viruses-infected cells, pointing towards a conserved feature through evolution. We hope that the information discussed in this review will give a better grasp of the biophysical mechanisms behind physiological and induced intracellular membrane proliferation, and inspire new applications, either for academia (high-yield membrane protein production and nanovesicle production) or industry (biofuel production and vaccine preparation).

Eukaryotic cells contain membranes with various curvatures, from the near-plane plasma membrane to the highly curved membranes of organelles, vesicles, and membrane protrusions. These curvatures are generated and sustained by curvature-inducing proteins, peptides, and lipids, and describing these mechanisms is an important scientific challenge. In addition to that, some molecules can sense membrane curvature and a thereby be trafficked to specific locations. The description of curvature-sensing is another fundamental challenge. Curved lipid membranes and their interplay with membrane-associated proteins can be investigated with molecular dynamics (MD) simulations, given the right tools. Various methods for simulating curved membranes with MD are discussed here, including tools for setting up simulation of vesicles, and methods for sustaining membrane curvature. The latter are divided into methods that exploit scaffolding virtual beads, methods that use curvature-inducing molecules, and methods applying virtual forces. The variety of simulation tools allow the researcher to closely match the conditions of experimental studies of membrane curvatures.

A unique method for synthesizing a surface modifier for metallic hydrogen permeable mem-branes based on non-classic bimetallic pentagonally structured Pd-Pt nanoparticles has been de-veloped. It was found that nanoparticles had unique hollow structure. This significantly reduces the cost of their production due to economical use of metal. According to the results of electro-chemical studies, synthesized bimetallic Pd-Pt/Pd-Ag modifier showed excellent catalytic activi-ty (up to 60.72 mA cm–2), long-term stability and resistance to COads poisoning in alkaline oxida-tion reaction of methanol. The membrane with pentagonally structured Pd-Pt/Pd-Ag modifier showed the highest hydrogen permeation flux density up to 27.3 mmol s–1 m–2. Obtained hy-drogen flux density were 2 times higher than that for membranes with classic Pdblack/Pd-Ag modifier and an order of magnitude higher than that for unmodified membrane. Since the rate of transcrystalline hydrogen transfer through a membrane increased, while the speed of transfer through defects remained unchanged, a one and a half times rise in selectivity of the developed Pd-Pt/Pd-Ag membranes was recorded and it amounted to 3514. Achieved results are due to both the synergistic effect of the combination of Pd and Pt metals in the modifier composition and the large number of available catalytically active centers, which are present as a result of non-classic morphology with high-index facets. The specific faceting, defect structure and unusual properties provide great opportunities for the application of nanoparticles in the areas of membrane reac-tors, electrocatalysis, petrochemical and hydrogen industries.

Diclofenac is a non-steroidal anti-inflammatory drug (NSAID) from the group of phenylacetic acid derivatives, which has analgesic, anti-inflammatory and antipyretic properties. The interaction of non-steroidal anti-inflammatory drugs with cell membranes can affect their physicochemical properties, which, in turn, can cause a number of side effects in the use of these drugs. Electron paramagnetic resonance (EPR) spectroscopy could be used to study the interaction of diclofenac with the membrane, if its spin-labeled analogs existed. This paper describes the synthesis of spin-labeled diclofenac (diclofenac-SL), which consists of a simple sequence of transformations such as iodination, esterification, Sonogashira cross-coupling, oxidation and saponification. EPR spectra showed that diclofenac-SL binds to in a lipid membrane composed of palmito-yl-2-oleoyl-sn-glycero-3-phosphocholine (POPC). 2H electron spin echo spectroscopy (ESEEM) was used to determine the position of the diclofenac-SL relative to the membrane surface. It has been established that the average its depth of immersion corresponds to the 5th position of the carbon atom in the lipid chain.

This research aimed to synthesize Polyvinyl fluoride (PVDF) membranes and coat them with Tannic acid (TA) nanoparticles and Polyethylene glycol (PEG) additives so that the membrane's removal efficacy for humic acid (HA) pollutant from agricultural wastewater was investigated. Thus, six membranes with PEG:TA ratios of 0:0, 1:0, 0:1, 1:1, 4:1 and 1:4 were synthesized. Then the membranes' characteristics were identified by FT-IR ATR, FESEM, and AFM analysis, and HA's particle size and zeta potential were also investigated. Based on optimizing effective parameters, the operating pressure of 1.5 bar and HA concentration of 80 ppm were selected as optimal values. The membrane with PEG:TA=4:1, as the optimally modified membrane, had a pure water flux of 446.03 L/m2.h, effluent flux of 72.43 L/m2.h and pollutant removal rate of 86.62% at pH=7 After 60 min had passed. These values for the pristine membrane (PEG:TA=0:0) were 265.64 L/m2.h, 89.39 L/m2.h, and 75.59%, respectively. The results showed that although the effluent flux was lower in the optimized modified membrane than in the pristine membrane, HA removal percentage was increased.

Flavonoids, polyphenols with anti-oxidative activity have high potential as novel therapeutics for neurodegenerative disease, but their applicability is rendered by their poor water solubility and chemical instability under physiological conditions. In this study, this is overcome by delivering flavonoids to model cell membranes (unsaturated DOPC) using prepared and characterized biodegradable mesoporous silica nanoparticles, MSNs. Quercetin, myricetin and myricitrin have been investigated in order to determine the relationship between flavonoid structure and protective activity towards oxidative stress i.e. lipid peroxidation induced by addition of hydrogen peroxide and/or Cu²⁺ ions. Among investigated flavonoids, quercetin showed the most enhanced and prolonged protective anti-oxidative activity. The nanomechanical (Young modulus) measurement of the MSNs treated DOPC membranes during lipid peroxidation confirmed attenuated membrane damage. By applying combination of experimental techniques (AFM, force spectroscopy, ELS, DLS), this work generated detailed knowledge about the effects of flavonoid loaded MSNs on the elasticity of model membranes, especially under oxidative stress conditions. Results from this study will pave the way towards the development of innovative and improved markers for oxidative stress-associated neurological disorders. In addition, the obtained could be extended to designing effective delivery systems of other high potential bioactive molecules with an aim to improve human health in general.

The purpose of this study is to identify the steps involved in fabricating silica/chitosan composite membranes and their suitability in fuel cell application. It also intends to identify the physical characteristics of chitosan composite membranes, including their degree of water absorption, proton conductivity, methanol permeability, and functional groups. In this investigation, composite membranes were fabricated using the solution casting method with chitosan content of 5 g and silica variations dosage of 2% and 4% while stirring at a constant speed for 2h. According to the findings, the analysis of composite membranes produced chitosan membranes that were successfully modified with silica. The optimum membrane was found to be 4% s-SiO2 from the Sol-gel method with composite membrane's optimal condition of 0.234 cm/s proton conductivity, water uptake of 56.21%, and reduced methanol permeability of 0.99 × 10 -7 cm2/s in the first 30 minutes and 3.31 × 10-7 in the last 150 minutes. Maintaining lower water uptake capacity at higher silica content is still a challenge that needs to be addressed. However, the fabricated membranes showed exceptional results in terms of proton conductivity and methanol permeability.

Membranes are a selective barrier that allows certain species (molecules and ions) to pass through while blocking others. Some rely on size exclusion, where larger molecules get stuck while smaller ones permeate through. Others use differences in charge or polarity to attract and repel specific species. Membranes can be used to purify air and water by allowing only air and water molecules to pass through but preventing contaminants such as microorganisms and particles or to separate target gas or vapor, such as H2, CO₂, from other gases. The higher the flux and selectivity, the better a material is for membranes. The desirable performance can be tuned through material type (polymers, ceramics, and biobased materials), microstructure (porosity and tortuosity), and surface chemistry. Most membranes are made from plastic from petroleum-based resources, which contribute to global climate change and plastic pollution. Cellulose can be an alternative sustainable resource to make renewable membranes. Cellulose exists in plant cell walls as natural fibers, which can be broken down into smaller components such as cellulose fibrils, nanofibrils, nanocrystals, and cellulose macromolecules through mechanical and chemical processing. Membranes made from reassembling these particles and molecules have variable pore architecture, porosity, and separation properties and therefore have a wide range of applications in nano-, micro-, and ultrafiltration or forward osmosis. Despite their advantages, cellulose membranes face some challenges. Improving the selectivity of membranes for specific molecules often comes at the expense of permeability. The stability of cellulose membranes in harsh environments or under continuous operation needs further improvement. Research is ongoing to address these challenges and develop advanced cellulose membranes with enhanced performance. This article reviews the microstructure, fabrication methods, and potential applications of cellulose membranes, providing some critical insights into processing-structure-property relationships for current state-of-the-art cellulosic membranes that could be used to rationally improve their performance.

Production of wastewater related to the oil and gas industries is increasing over the years. The compounds found in industrial wastewater typically show high toxicity, and in this way, they have become a primary environmental concern. Several techniques have been applied in industrial effluents remediation. In spite of the efforts, these techniques are yet ineffective to treat oily wastewater before it can be discharged safely to the environment. Membrane technology is an attractive approach to treat oily wastewater. This is dedicated to the immobilisation of TiO2 nanoparticles on poly (vinylidene fluoride–trifluoro ethylene) (PVDF-TrFE) porous matrix by solvent casting. Membranes with interconnected pores with an average diameter of 60 micrometres and the contact angle of 97°, decorated with TiO2 nanoparticles, are obtained. The degradation of oily wastewater demonstrated the remarkable photocatalytic efficiency of the nanocomposite membranes: under sunlight irradiation for 7 hours, colourless water was obtained. These results show the suitability of TiO2/P(VDF–TrFE) nanocomposite for photocatalytic applications for oily wastewater remediation.

The need for solvating and encapsulating hydro-sensitive molecules drives noticeable trends in the applications of cyclodextrins in pharmaceutical industry, food, polymer, materials, and agricultural science. Among them, β-cyclodextrin is one of the most used for the entrapment of phenolic acid compounds to mask the bitterness of wheat bran. In this regard, there is still a need for a good predictive model that assesses β-cyclodextrin bitterness masking capabilities for various phenolic compounds. This study uses a dataset of 20 phenolic acids docked to the β-cyclodextrin cavity to generate three different binding constants. The data from docking study were combined with topological, topographical and quantum-chemical features from the ligands in a machine learning-based structure-activity relationship study. Three different models for each binding constant were computed using a combination of Genetic Algorithm (GA) and Multiple Linear Regression (MLR) approaches. The developed ML/QSAR models showed a very good performance, with high predictive ability and correlation coefficients of 0.969 and 0.984, for training and test sets, respectively. The models revealed several factors responsible for a binding with cyclodextrin, showing positive contributions toward the binding affinity values, including such features as presence of six-membered rings in the molecule, branching, electronegativity values, and polar surface area.

Materials based on platinum metals with very good catalytic activity were tested in the reduction of p–nitrophenol (pNP) to p–aminophenol (pAP). The majority of presented catalytic materials are based on the adsorption of p–nitrophenol on the surface of the catalyst simultaneously with molecular hydrogen, coming from sodium borohydride in an aqueous medium, which reduces it. In the present paper, a catalytic material based on osmium dispersed in n–decanol or n–dodecanol is presented, which also works as an emulsion membrane, for the absorption of p–nitrophenol and molecular hydrogen at the n–alcohol aqueous solution interface. The hydrogenation of p–nitrophenol is carried out in a reaction and separation column in which the acid receiving phase emulsion is dispersed in the osmium nanodispersion, in n–alcohols. This emulsion circulates from the base of the column to its upper part in co-current or counter-current with the source phase consisting of p–nitrophenol and sodium borohydride. Experiments show that the circulation of counter-current phases is superior to that in co-current, and the emulsion based on n–decanol is more efficient than the one based on n–dodecanol. The increase in the pH difference between the source and receiving phases leads to the increase in the conversion of p–nitrophenol to p–aminophenol. The efficiency of separation of the reaction product in the receiving phase is lower than the conversion at the same operating time. The apparent catalytic rate constant (kapp) of the new catalytic material based on the emulsion membrane with nanodispersion of osmium nanoparticles (0.1×10−3 for n–dodecanol and 0.9×10−3 for n-decanol) is lower by an order of magnitude compared to those based on adsorption on catalysts from platinum metal group. The advantage of the tested membrane catalytic material is that it extracts p–aminophenol in the acid receiving phase. The paper proposes a mechanism of the studied reduction system.

Composite membranes formed by sulfonated poly(ether ether ketone) (SPEEK) with embedded carbon quantum dots (CQDs) were used for detection and removal of heavy metal ions, such as lead and cadmium, from water. SPEEK is responsible for the capture of heavy metals based on the cation exchange mechanism, while CQDs detect their contamination by exhibiting changes in fluorescence. Water-insoluble “red” carbon quantum dots (rCQDs) were synthesized from p-phenylenediamine so that their photoluminescence was shifted from that of the polymer matrix. CQDs and the composites were characterized by several techniques: FTIR, Raman, UV/VIS, photoluminescence, XPS spectroscopies and AFM microscopy. The heavy metal ion concentration was analyzed by inductively coupled plasma–optical emission spectroscopy (ICP-OES). The concentration ranges were 10.8 - 0.1 mM for Pb2+ and 10.0 - 0.27 mM for Cd2+. The composite achieved 100% removal efficiency for lead and cadmium if the concentration was below a half of the ion exchange capacity of SPEEK. The regeneration of membranes in 1 M NaCl was also studied. SPEEK/rCQDs showed a turn-off effect more pronounced for lead. A second order law was effective to describe the kinetics of the process.

In a previous study we could show a change of membrane morphology and gas separation performance by varying the recipe of a casting solution based on polysulfone in a determined solvent system. Although all results were very reproducible, all used solvents were harmful and not sustainable. In this study therefore, the solvents tetrahydrofuran (THF) and N,N-dimethylacetamide (DMAc) are replaced by the more sustainable solvents 2-methyl-tetrahydrofuran (2M-THF), N-butyl pyrrolidinone (NBP) and cyclopentyl methyl ether (CPME). The gas permeation performance and for the first time morphology of the membranes before and after solvent replacement were determined and compared by single gas permeation measurements and SEM microscopy. It is shown, that THF can be replaced by 2M-THF and NBP without decreasing the gas permeation performance. With CPME replacing THF no membranes were formed. Best gas permeation results showed systems with 2M-THF as THF alternative. Permeances for the tested gases oxygen (O2), nitrogen (N2), carbon dioxide (CO2) and methane (CH4) were 2.66·10-4, 3.89·10-5, 1.53·10-3 and 4.52·10-5 mL(STP)/cm²·min·bar, respectively. permselectivities of those membranes for the gas pairs O2/N2, CO2/N2 and CO2/CH4 were 6.7, 38.3 and 34.0, respectively. When additionally replacing DMAc in the solvent system no or only porous membranes were obtained, even if the precipitation procedure was adjusted. These findings indicate that a complete replacement of the solvent system without affecting the membrane morphology or gas permeation performance is not possible. By varying the temperature of the precipitation bath an easy adjustment to mechanically stable PSU membranes is possible, if just THF was replaced by 2M-THF.

Thin supported inorganic mesoporous membranes are used for removal of salts, small molecules (PFAS, dyes, polyanions) and particulate species (oil droplets) from aqueous sources with high flux and selectivity. Nano-filtration membranes can reject simple salts with 80-100% selectivity through a space charge mechanism. Rejection by size selectivity can be near 100% since the membranes can have a very narrow size distribution. Mesoporous membranes have received par-ticular interest due to their (potential) stability at operational conditions and defouling operations. More recently membranes with extreme stability became interesting with the advent of in-situ fouling mitigation by means of ultrasound, emitted from within the membrane structure. For this reason we explored the stability of available and new membranes with accelerated lifetime tests in aqueous solutions at various temperatures and pH values. Of the available ceria, titania, mag-netite membranes none were actually stable at all test conditions. In earlier work, it was already established that meso-porous alumina membranes have very poor stability. A new nano-filtration membrane was made of cubic zirconia membranes that exhibited a near perfect stability. A new ultra-filtration membrane was made of amorphous silica that was fully stable in ultrapure water at 80°C. This work provides details of membrane synthesis, stability characterization and actual sta-bility data.

Wound infection is a common complication of chronic wounds. It can impair healing, which may not occur without external help. Antimicrobial dressings (AMDs) are a type of external help to infected chronic wounds. In this study, highly porous membranes made of only chitosan and containing the antiseptic polyhexanide (poly(hexamethylene biguanide); PHMB) were prepared by cryogelation, aiming to be used in AMDs. These membranes exhibited high water swelling capacity, fast water absorption and high water vapor transmission. The best drug loading method involved simultaneous loading by soaking in a PHMB solution and sterilization by autoclaving, resulting in sterilized, drug-loaded membranes. The drug release kinetics was comparable to that of a commercial PHMB-releasing AMD assayed under the same conditions. These membranes exhibited high antibacterial activity against Escherichia coli, Staphylococcus aureus and Pseudomonas aeruginosa, which are bacterial species commonly found in infected wounds, and blood clotting activity. The obtained results suggest that these membranes may be suitable for use in the development of AMDs.

In this report we have discussed the important role of molecular modeling, especially the use of the molecular dynamics method, in investigating transport processes in nanoporous materials such as membranes. With the availability of high performance computers, molecular modeling can now be used to study rather complex systems at a fraction of the cost or time requirements of experimental studies. Molecular modeling techniques have the advantage of being able to access spatial and temporal resolution which are difficult to reach in experimental studies. For example, sub-Angstrom level spatial resolution is very accessible as is sub-femtosecond temporal resolution. Due to these advantages, simulation can play two important roles: Firstly because of the increased spatial and temporal resolution, it can help understand phenomena not well understood. As an example, we discuss the study of reverse osmosis processes. Before simulations were used it was thought the separation of water from salt was purely a coulombic phenomenon. However, by applying molecular simulation techniques, it was clearly demonstrated that the solvation of ions made the separation in effect a steric separation and it was the flux which was strongly affected by the coulombic interactions between water and the membrane surface. Additionally, because of their relatively low cost and quick turnaround (by using multiple processor systems now increasingly available) simulations can be a useful screening tool to identify membranes for a potential application. To this end, we have described our studies in determining the most suitable zeolite membrane for redox flow battery applications. As computing facilities become more widely available and new computational methods are developed, we believe molecular modeling will become a key tool in the study of transport processes in nanoporous materials.

Titanium membranes are used for guided bone regeneration in implant therapy. However, as a bioinert material, titanium does not have the ability to accelerate bone formation. Various titanium surface treatments to confer bioactivity have been demonstrated; however, there are concerns about the influence of chemical treatments on the corrosion of thin titanium membranes. This study investigated the influence of surface modifications on the structure of thin titanium membranes. Titanium membranes of 20 µm thickness were treated with acid or alkali solutions, and we evaluated their surface structure, wettability, corrosion depth, and mechanical strength compared to non-treated membranes. Alkali-treated thin titanium membranes displayed the formation of nanoscale pore structures on their surfaces, enhanced hydrophilicity, and less corrosion depth compared with acid-treated membranes. Furthermore, the tensile strength of alkali-treated membranes was comparable to non-treated membranes. These results suggest that alkali treatment is an appropriate surface modification method for thin titanium membranes.

In this work, the surface of poly(ethylene terephthalate) track-etched membranes (PET TeMs) with pore sizes of 670-1310 nm was hydrophobized with 2,2,3,3,4,4,5,5,6,6,7,7-dodecafluoroheptyl acrylate (DFHA) by photoinitiated graft polymerization. Attenuated total reflection FTIR spec-troscopy (ATR-FTIR), scanning electron microscopy (SEM) coupled to an energy-dispersive X-ray spectrometer (EDX), and contact angle measurement were used to identify and characterize the TeMs. The optimal parameters for graft polymerization were determined as follows: polymeriza-tion time 60 min, monomer concentration of 30% and distance from the UV-source 7 cm. The wa-ter contact angle of the modified membranes reached 97° which is 51o for pristine membranes. The modified membranes were tested for water desalination using direct contact membrane distillation (DCMD) method. The effect of membrane pore size, the degree of grafting and salt concentration on the performance of membrane distillation process was investigated. According to the results obtained, it has been concluded that large pore size hydrophobic TeMs modified by using DFHA could be used for desalinating water.

Reversible protonic ceramic cells (rPCCs) combine two different operation regimes, fuel cell and electrolysis cell modes, which allow reversible chemical-to-electrical energy conversion at reduced temperatures with high efficiency and performance. Here we present novel technological and materials science approaches, enabling a rPCC with symmetrical functional electrodes to be prepared using a single sintering step. The response of the cell fabricated on the basis of P–N–BCZD|BCZD|PBN–BCZD (where BCZD = BaCe_0.5Zr_0.3Dy_0.2O_3–δ, PBN = Pr_1.9Ba_0.1NiO_4+δ, P = Pr₂O₃, N = Ni) is studied at different temperatures and water vapor partial pressures (pH₂O) by means of volt-ampere measurements, electrochemical impedance spectroscopy and distribution of relaxation times analyses. The obtained results demonstrate that symmetrical electrodes exhibit classical mixed-ionic/electronic conducting behavior with no hydration capability at 750 °C; therefore, increasing the pH₂O values in both reducing and oxidizing atmospheres leads to some deterioration of their electrochemical activity. At the same time, the electrolytic properties of the BCZD membrane are improved, positively affecting the rPCC’s efficiency. The electrolysis cell mode of the rPCC is found to be more appropriate than the fuel cell mode under highly humidified atmospheres, since its improved performance is determined by the ohmic resistance, which decreases with pH₂O increasing.

Detecting and monitoring changes in soil salinity through remote sensing provides an opportunity for field assessment in regions where on-site measurements are limited. This investigation, carried out in Siwa Oasis, Egypt, aimed to assess the efficacy of several soil salinity indices derived from Landsat 5 and 7 satellite images. To achieve this, 56 on-site ground measurements were utilized for evaluation purposes. The study aimed to improve the correlation between EC and index values and explore the relationship between salinity and changes in land cover. Eleven spectral indices were calculated for nine scenes captured in different months from August to December. The first approach involved stacking the data to identify the index with the strongest correlation with ground EC values, without the need for complex analysis or EC value ranging. In the second approach, the ground EC measurements were classified into seven different salinity categories, and the correlation coefficient was calculated between each index and each salinity category. The third approach analyzed the data temporally, considering different salinity levels. Lastly, a spatial correlation analysis was conducted between EC and index values in the fourth scenario. The initial approach revealed a weak correlation due to substantial variation in EC values. However, the SI index demonstrated the highest correlation coefficient of 0.38. In the second scenario, the S2 index exhibited the highest correlation of 0.96 for moderate salinity samples. The third scenario showed that the S1 index achieved the highest correlation value of 0.99 for moderately saline areas. In the fourth scenario, the SI index exhibited the strongest correlation among all four ponds with correlation coefficients of 0.23, 0.23, 0.18, and 0.61. Notably, the correlations observed in the second and third scenarios demonstrated higher correlation coefficients compared to both the first and fourth scenarios. The study highlighted significant variations in EC levels related to land cover types and pond elevation. Additionally, remote sensing methods detected a 48% increase in total vegetated area over 17 years, showing the potential of remote sensing techniques in salinity monitoring for expanding agriculture and improving land management.

A membrane can be represented by an energy landscape that solutes or colloids must cross. A model accounting for the momentum and the mass balances on the membrane energy landscape establishes a new way of writing for the Darcy law. The counter pressure in the Darcy law is no longer written as the result of an osmotic pressure difference but rather as a function of colloid-membrane interactions. The ability of the model to describe the physics of the filtration is discussed in detail. This model is solved on a simplified energy landscape to derive analytical relationships that describe the selectivity and the counter pressure from ab-initio operating conditions. The model shows that the stiffness of the energy landscape has an impact on the process efficiency: a gradual increase in interactions (like with hourglass pore shape) can reduce the separation energetic cost. It allows the introduction of a new paradigm to increase membrane efficiency: the accumulation that is inherent to the separation must be distributed across the membrane. Asymmetric interactions thus lead to direction-dependent transfer properties and the membrane exhibits diode behavior. These new transfer opportunities are discussed.

The degradation and detachment of the polyamide (PA) layer in thin-film composite (TFC) membranes due to chlorine based chemical cleaning and material difference of PA layer and substrate are two major bottlenecks of forward osmosis (FO) technology. In this study, a new type of FO membranes were prepared by controlling self-polymerization of dopamine (DA) in the aqueous phase and the reaction with trimesoyl chloride (TMC) during interfacial polymerization (IP) process. These membranes were characterized by attenuated total reflection Fourier transform infrared (ATR-FTIR), X-ray photoelectron spectroscopy (XPS), field-emission scanning electron microscopy (FESEM) and water contact angle measurements. The influence of synthesis parameters such as pH of the aqueous phase, reaction time, temperature, and monomer concentrations were systematically investigated. The optimized membrane showed enhanced structure stability in ethanol (7.1 times higher) and chlorine resistance (72.3 times higher) than the conventional Piperazine(PIP)/TMC membrane due to（poly-dopamine）PDA bio-adhesion and polyester groups in the membrane structure. In general, DA/TMC membranes could be an effective strategy to fabricate high-performance FO membranes with excellent structural stability and chlorine resistance.

Membrane filtration is a popular choice in the treatment of wastewater for reuse. However, when used to produce clean water, these devices are subject to concentration polarization and fouling, which inhibit their ability to operate efficiently and provide high-quality permeate streams. Patterned membrane surfaces offer a hydrodynamic approach to mitigating concentration polarization and the surface fouling that follows. However, when subject to a steady feed flow rate, surface patterns generally produce stagnant zones in cavity-like spaces where particulate from the bulk flow recirculates in stationary vortices. To prevent aggregation in these recirculation zones, and therefore the onset of surface fouling, we study a rapidly pulsed feed flow. When combined with cavity-like geometries, such as the valleys present in membrane surface patterns, a rapidly pulsed flow generates mixing mechanisms (i.e., the deep sweep and the vortex ejection) that disrupt otherwise stagnant regions. First, we confirm the existence of these mechanisms, which are typically induced in impermeable cavities at relatively low Reynolds numbers, for near transitional feed Reynolds numbers in permeable cavity spaces via numerical simulation of the flow field. Following this confirmation, we demonstrate the ability of these mechanisms to remove particles trapped in recirculation zones via massless particle tracking studies. The results of this work suggest that when combined with a rapidly pulsed inlet flow, patterned membrane surfaces can not only alleviate concentration polarization and the surface fouling that follows but also reduce the need for traditional cleaning methods, which require operational downtime and often involve the use of abrasive chemical agents.

One of the most broadly used models for membrane fouling is the Hermia model, which separates this phenomenon into four blocking mechanisms, each with an associated parameter n. These mechanisms are complete blocking (n=2), intermediate blocking (n=1), standard blocking (n=3/2), and cake formation (n=3/2). The original model, which was obtained through experimental data, is given by an Ordinary Differential Equation (ODE) dependent on n. At the time, this ODE was only solved for these four values of n, which limits the effectiveness of the model when adjusted to experimental data. This paper aims to not only mathematically prove the original Hermia model but also to broaden the scope of this model for any real number n by using the original ODE, the equations of fluid mechanics, and the properties of single and multivariable calculus. The extended Hermia model (EHM) is given by a power law for any n≠2 and is given by an exponential function at n=2. To better test the model, we have performed the model fitting of the EHM and compared its performance to the original four pore-blocking mechanisms in 6 micro- and ultrafiltration examples. In all examples, the EHM performed consistently better than the four original pore-blocking mechanisms. Changes in the blocking mechanisms concerning transmembrane pressure (TMP), crossflow rate (CFR), crossflow velocity (CFV), membrane composition, and pretreatments are also discussed.

membrane separation technology shows promise, particularly gas separation membranes, including ceramic membrane. Ceramic membranes are increasingly gaining attention for their acid and alkali stability, corrosion resistance, high-temperature tolerance, and mechanical strength. This study focuses on alumina support ceramic membrane for CO2 capture. The membranes were characterized using contact angle measurements, scanning electron microscopy (SEM), and Fourier Transform Infrared spectroscopy (FTIR) analysis. The contact angle measurements confirmed the hydrophilic, while SEM analysis showed even particle distribution in the alumina ceramic membranes respectively. EDAX analysis revealed the elemental composition in the alumina support matrix. FTIR analysis demonstrated chemical interactions of the support membrane. Single gas permeation experiments were conducted. It can be observed that Nitrogen gas permeated faster with increase in feed pressure through the unmodified ceramic inorganic hydrophobic membrane more than the other two single gases, O2, and CO2). As a result, only high permeance separation membranes with realistic size and pressure conditions may be considered of as a practical alternative for CO2 capture. However, the presence of non-selective defects limited the improvement in selectivity of hydrophilic ceramic membrane. In this case, there is need to modify the ceramic membrane used to increase the flux, permeance of CO2, and selectivity of CO2.

Abstract: membrane separation technology shows promise, particularly gas separation membranes, including ceramic membrane. Ceramic membranes are increasingly gaining attention for their acid and alkali stability, corrosion resistance, high-temperature tolerance, and mechanical strength. This study focuses on alumina support ceramic membrane for CO2 capture. The membranes were characterized using contact angle measurements, scanning electron microscopy (SEM), and Fourier Transform Infrared spectroscopy (FTIR) analysis. The contact angle measurements confirmed the hydrophilic, while SEM analysis showed even particle distribution in the alumina ceramic membranes respectively. EDAX analysis revealed the elemental composition in the alumina support matrix. FTIR analysis demonstrated chemical interactions of the support membrane. Single gas permeation experiments were conducted. It can be observed that Nitrogen gas permeated faster with increase in feed pressure through the unmodified ceramic inorganic membrane more than the other two single gases, O2, and CO2). As a result, only high permeance separation membranes with realistic size and pressure conditions may be considered of as a practical alternative for CO2 capture. However, the presence of non-selective defects limited the improvement in selectivity of hydrophilic ceramic membrane. In this case, there is need to modify the ceramic membrane used to increase the flux, permeance of CO2, and selectivity of CO2.

The oscillating heat pipe (OHP) is a new member in the family of heat pipes, and it has great potential applications in energy conservation. However, the fluid flow and heat transfer in the OHP as well as the fundamental effects of inner diameter on them have not been fully understood, which are essential to the design and optimization of the OHP in real applications. Therefore, by combining the high-speed visualization method and infrared thermal imaging technique, the fluid flow and thermal performance in the OHPs with inner diameters of 1, 2 and 3 mm are presented and analyzed. The results indicate that three fluid flow motions, including small oscillation, bulk oscillation and circulation, coexist or, respectively, exist alone with the increasing heating load under different inner diameters, with three flow patterns occurring in the OHPs, viz. bubbly flow, slug flow and annular flow. These fluid flow motions are closely correlated with the heat and mass transfer performance in the OHPs, which can be reflected by the characteristics of infrared thermal images of condensers. The decrease in the inner diameter increases the frictional flow resistance and capillary instability while restricting the nucleate boiling in OHPs, which leads to a smaller proportion of bubbly flow, a larger proportion of short slug flow, a poorer thermal performance, and easier dry-out of working fluid. In addition, when compared with the 2 mm OHP, the increasing role of gravity induces the thermosyphon effect and weakens the 'bubble pumping' action, which results in a little smaller and bigger thermal resistances of 3 mm OHP under small and bulk oscillation of working fluid, respectively.

When the epipelic algae group growing on the concrete inclined side wall, which is typical of urban rivers and open diversion channels, enters the water flow, it will seriously affect the func-tion of the rivers or the channels. It is urgent to predict the transport capacity of epipelic algae group with water flow. However, the current research on the transport of pollutants is mostly based on mathematical models, and the study of the transport of flake epipelic algae group is extremely rare. A generalized hydrodynamic experimental model of a flume with sidewall epi-pelic algae group was established. Through a series of hydraulic experiments, the physical movement form and transport capacity of the suspended epipelic algae group on the side wall of the channel were studied qualitatively and quantitatively by taking the thickness, sheet size and flow rate of the epipelic algae group as the influencing factors. The key influencing factors of the suspension of epipelic algae are clarified, so as to quantitatively analyze the critical conditions of its suspension. Through flow scheduling, the probability of epipelic algae gathering some-where is increased. It provides a theoretical basis for realizing the long-distance migration of epipelic algae and optimizing the mathematical model.

Hoechst 33342 (H33342) is a fluorescent probe that is commonly used to stain DNA of living cells. To do so, it needs to interact with and permeate through cell membranes. The pH of biological media may vary quite significantly and this influences H33342 ionization state, and may change its rate of permeation through biomembranes. In this work, we address the effect of pH in the association of H33342 with lipid bilayers using a combined experimental and computational approach. The partition of H33342 to 1-palmitoyl-2-oleoyl-sn-glycero-3-phosphocholine (POPC) lipid membranes was experimentally quantified using fluorescence spectroscopy and isothermal titration calorimetry (ITC) measurements. Quantum chemical calculations were performed to select the most stable isomer of H33342 for the overall charges 0, +1, and +2, expected to predominate across the 5 < pH < 10 range. The interaction of these isomers with POPC bilayers was then studied by both unrestrained and umbrella sampling molecular dynamics simulations. While probe insertion occurs for all ionization states, with similar overall equilibrium location, orientation was found to depend on the probe charge, with the neutral form lying mostly parallel and the doubly charged displaying a significant tilt relative to the membrane plane. Both experimental results and computational free energy profiles indicate that the partition coefficient of H33342 displays a small variation over a wide pH range, not exceeding one order of magnitude. The enthalpy of interaction is negative and is larger at lower pH values. This suggests efficient hydrogen bonding between the probe and the lipid, namely for the protonated +2 form. The relatively high lipophilicity obtained for the charged species contrasts with the decrease in their general hydrophobicity as estimated from water and octanol partition. This highlights the distinction between lipophilicity and hydrophobicity, and the importance of considering association with lipid bilayers when predicting the affinity for biomembranes.

The prevalence for chronic, non-healing skin wounds in the general population, most notably diabetic foot ulcers, venous leg ulcers and pressure ulcers, is approximately 2% and is expected to increase, driven mostly by an aging population and the steady rise in obesity and diabetes. Non-healing wounds often become infected, increasing the risk of life-threatening complications, which poses a significant socioeconomic burden. Aiming at an improved management of infected wounds, a variety of wound dressings incorporating antimicrobials (AMDs), namely polyhexanide (poly(hexamethylene biguanide); PHMB), have been introduced in the wound care market. However, many wound care professionals agree that none shows comprehensive and optimal antimicrobial activity. This manuscript summarizes and discusses studies on novel PHMB-releasing membranes (PRMs) for wound dressings, detailing their preparation, physical properties relevant in the context of AMDs, drug loading and release, antibacterial activity, biocompatibility, wound healing capacity, and clinical trials conducted. Some of these PRMs were able to improve wound healing in in vivo models, with no associated cytotoxicity, but significant differences in study design make it difficult to compare overall effi-cacies. It is hoped that this review, which includes, whenever available, international standards for testing AMDs, will provide a framework for future studies.their preparation, physical properties relevant in the context of AMDs, drug loading and release, antibacterial activity, biocompatibility, wound healing capacity, and clinical trials conducted. Some of these PRMs were able to improve wound healing in in vivo models, with no associated cytotoxicity, but significant differences in study design make it difficult to compare overall efficacies. It is hoped that this review, which includes, whenever available, international standards for testing AMDs, will provide a framework for future studies.

Bioelectrochemical systems (BES) encompass a group of biobased technologies capable of directly converting organic matter into electricity. In these systems, which are derived from conventional electrochemical systems, the ion exchange membrane represents a key element because of its influence on the economic feasibility and on the performance of BES. This study examines the impact of long-term operation of a BES on the mechanical, chemical and electrochemical properties of five different kind of cation exchange membranes (Nafion-117, CMI-7001, Zirfon UTP 500, FKE and FKB) through several techniques: (i) scanning electron microscopy (SEM) and atomic force microscopy (AFM) to assess the changes on the membranes surface, (ii) thermogravimetric analysis (TGA) to evaluate the structural stability of the membranes, and (iii) ion exchange capacity (IEC) to monitor any change in their electrochemical properties. Results confirmed that there is not an ideal membrane for BES. While Nafion and CMI-7000 exhibited the strongest chemical structure, they also underwent the highest fouling as revealed by a fast increase in surface roughness.

Considering the high potential of hydrogen (H₂) as a clean energy carrier, the implementation of high performance and cost-effective biohydrogen (bioH₂) purification techniques is of vital importance, particularly in fuel cell applications. In this context, membrane technology is a potentially energy-saving solution to obtain high-quality biohydrogen. The most promising poly(ionic liquid) (PIL) - ionic liquid (IL) composite membranes previously studied by our group for CO₂/N₂ separation, containing pyrrolidinium-based PILs with fluorinated or cyano-functionalized anions, were chosen as starting point to explore the potential of PIL–IL membranes for CO₂/H₂ separation. The CO₂ and H₂ permeation properties at the typical conditions of biohydrogen production (T =308 K and 100 kPa of feed pressure) were measured and discussed. PIL–IL composites prepared with [C(CN)₃]^– anion showed higher CO₂/H₂ selectivities and H₂ diffusivities compared to those containing [NTf₂]^– anion. All the membranes revealed CO₂/H₂ separation performances above the upper bound for this specific separation, highlighting the composite incorporating 60 wt% of [C₂mim][C(CN)₃] IL.

This review provides informations and details for the fabrication of biosensors that are composed from lipid membranes and have been utilized and applied to rapidly detect food toxic compounds, environmental pollutants and analytes of clinical interest. Biosensors based on polymeric lipid membranes have been used to rapidly detect a wide range of these analytes and offer several advantages such as fast response, high sensitivity and selectivity, can be portable for in the field applications, and small size. A description of the construction of these devices and their applications for the rapid detection of food toxic substance, environmental pollutants and analytes of clinical interest is provided in this review.

Dogs population increased exponentially in the past decade while the birth rate decreased gradually, especially in the developed countries. Due to dogs’ characteristics of loyalty and obedience, most pet owners treated their dogs as their family members or companions, therefore they are willing to select and purchase safe, high quality and nutrition dog food to their dogs. However, there is lack of regulation or standard to reinforce the production or distribution of dog food in Hong Kong. Consequently, this paper will first review the relationship between high dog population and declining birth rate, types of dog food and typical ingredients. Secondly, the potential health implications of various “toxic” food ingredients for dog, hazard analysis of dog food and its testing methods will be investigated. Lastly, this paper will summarize worldwide existing standards and regulations, quality and hygiene management system related to dog food safety to provide insights and suggestions to Hong Kong government about the importance and urgency of implementing regulations and policies to oversee the imported and local manufactured dog food.

Significant amount of oil remains in the reservoir after primary and secondary operations and to recover the remaining oil, enhanced oil recovery (EOR) can be applied as one of the feasible options remaining nowadays. In this study new nano polymeric materials have been prepared from purple yam and cassava starches. The yield of purple yam nanoparticles (PYNPs) was 85% and that of cassava nanoparticles (CSNPs) is 90.53%. Synthesized materials were characterized through particle size distribution (PSA), zeta potential distribution, Fourier transform infrared spectroscopy (FTIR), differential scanning calorimetry (DSC) and transmission electron microscopy (TEM). The performance of PYNPs in recovering oil was better than CSNPs as found from recovery experiments. Zeta potential distribution results confirmed the stability of PYNPs over CSNPs (-36.3 mV for PYNPs and -10.7 mV for CSNPs). The optimum concentration for these nanoparticles has been found from interfacial tension measurements and rheological properties and it was 0.60 wt.% for PYNPs and 0.80 wt.% for CSNPs. More incremental recovery (33.46%) has achieved for the polymer that contained PYNPs in comparison to the other nano-polymer (31.3%). This opens the inception for a new technology for polymer flooding that may replace the conventional method that depends on partially hydrolyzed polyacrylamide (HPAM).

Metal-organic frameworks (MOFs) represent the largest class of materials among the crystalline porous materials ever developed and have attracted attention as core materials for separation technology. Their extremely uniform pore aperture and nearly unlimited structural and chemical characteristics have attracted great interest and promise in applying MOFs to adsorptive and membrane–based separations. This paper reviews the recent research and development of MOF membranes for gas separation. Strategies for polycrystalline membranes and mixed matrix membranes are discussed, with a focus on separation systems involving hydrocarbon separation and CO2 capture. Challenges and opportunities for the industrial deployment of MOF membranes are also be discussed, providing guidance for the design and fabrication of future high-performance membranes. The contributions of the underlying mechanism to separation performances, and the adopted strategies and membrane processing technologies for breaking the selectivity/permeability trade–off are discussed.

Gold nanoparticles (AuNPs) are promising candidates in various biomedical applications such as sensors, imaging, and cancer therapy. Understanding the influence of AuNPs on lipid membranes is important to assure their safety in the biological environment and to improve their scope in nanomedicine. In this regard, the present study aims to analyze the effects of different concentrations (0.5, 1, and 2 w %) of dodecanethiol functionalized hydrophobic AuNPs on the structure and fluidity of zwitterionic 1-stearoyl-2-oleoyl-sn-glycerol-3-phosphocholine (SOPC) lipid bilayer membranes using Fourier transform infrared (FTIR) spectroscopy and fluorescent spectroscopy. The size of AuNPs was found to be 2.2 ± 1.1 nm using transmission electron microscopy. FTIR results have shown that the AuNPs induced a slight shift in methylene stretching bands, while the band positions of carbonyl and phosphate group stretching were unaffected. Temperature-dependent fluorescent anisotropy measurements have shown that the incorporation of AuNPs up to 2 w % did not affect the lipid order in membranes. Overall, these results indicate that the hydrophobic AuNPs in the studied concentration did not cause any significant alterations in the structure and membrane fluidity, which suggests the suitability of these particles to form liposome-AuNP hybrids for diverse biomedical applications including drug delivery and therapy.

It is known that ammonium has a higher permeability through anion-exchange and bipolar membranes compared to K+ cation that has the same mobility in water. However, the mechanism of this high permeability is not clear enough. We develop a mathematical model based of the Nernst-Planck and Poisson equations for diffusion of ammonium chloride through an anion-exchange membrane; proton exchange reactions between ammonium, water and ammonia are taken into account. It is assumed that ammonium, chloride and OH− ions can only pass through membrane hydrophilic pores, while ammonia can also dissolve in membrane matrix fragments not containing water and diffuse through these fragments. It is found that due to the Donnan exclusion of H+ ions as coions, the pH in the membrane internal solution increases when approaching the membrane side facing distilled water. Consequently, there is a change in the principal nitrogen-atom carrier in the membrane: in the part close to the side facing the feed NH4Cl solution (pH<8.8), it is the NH4+ cation, and in the part close to distilled water, NH3 molecules. The concentration of NH4+ reaches almost zero at a point close to the middle of the membrane cross-section, which approximately halves the effective thickness of the diffusion layer for the transport of this ion. When NH3 takes over the nitrogen transport, it only needs to pass through the other half of the membrane. Leaving the membrane, it captures an H+ ion from water, and the released OH− goes towards the membrane side facing the feed solution to meet the NH4+ ions. The comparison of the simulation with experiment shows a satisfactory agreement.

Over the last two decades, microfluidics has received significant attention from both academia and industry, and researchers report thousands of new prototype devices each year for use in a broad range of environmental, pharmaceutical, and biomedical engineering applications. While lab-on-a-chip fabrication costs have continued to decrease, the hardware required for monitoring fluid flows within microfluidic devices themselves remains expensive and often cost prohibitive for researchers interested in starting a microfluidics project. As microfluidic devices become capable of handling complex fluidic systems, low-cost, precise and real time pressure and flow rate measurement capabilities has become increasingly important. While many labs use commercial platforms and sensor, these solutions can often cost thousands of dollars and can be too bulky for on-chip use. Here we present a new inexpensive and easy -to-use piezoresistive pressure and flow sensor that can be easily integrated into existing on-chip microfluidic channels. The sensor consists of PDMS-Carbon black conductive membranes and uses an impedance analyzer to measure impedance change due fluid pressure. The sensor costs several orders of magnitude less than existing commercial platforms and can monitor local fluid pressures and calculate flow rates based on pressure gradient.

A simple model is developed for membrane fouling, taking into account two main fouling phenomena: cake formation, due to attached solids onto the membrane surface and pores clogging, due to retained compounds inside the pores. The model is coupled with a simple anaerobic digestion model for describing the dynamics of an Anaerobic Membrane BioReactor (AnMBR). In simulations, we investigate its qualitative behavior: it is shown that the model exhibits satisfying properties in terms of flux decrease due to membrane fouling. Comparing simulation and experimental data, the model is shown to predict quite well the dynamics of an AnMBR. The simulated flux best fits the experimental flux with a correlation coefficient r2=0.968 for the calibration data set and r2=0.938 for the validation data set. General discussions are given on possible control strategies to limit fouling and optimize the flux production. We show in simulations that these strategies allow one to increase the mean production flux to 33 L/(h.m2), whereas without control it was 18 L/(h.m2).

This study aims to investigate the interfacial tension, emulsion stability, and the impact on oil displacement effectiveness of mixed systems containing nonionic surfactants and amphoteric surfactants at different ratios. To achieve this, three different emulsion stability formulations were prepared by mixing betaine and nonionic surfactants in ratios of 1:1, 3:2, and 3:1 respectively. By adjusting the proportions of betaine and nonionic surfactants, variations in interfacial tension and emulsion formation among the three mixed systems were studied to analyze the mechanism of interaction between betaine and nonionic surfactants and evaluate their effects on crude oil displacement and enhanced oil recovery in reservoirs. Subsequently, microscopic and macroscopic oil displacement experiments were conducted on the three mixed systems, along with experiments on emulsion flow resistance. The aim was to verify the oil displacement effectiveness of different mixed systems and further understand their potential applications in reservoirs. By comprehensively analyzing the experimental results, optimal ratios and conditions for the mixed systems were determined. The experimental results indicate that the emulsification system formed by mixing betaine and nonionic surfactants at a ratio of 3:1 achieves molecular synergies through electrostatic interactions and mixed adsorption with betaine, resulting in a compact arrangement of interface membranes and demonstrating a synergistic effect in reducing interfacial tension to an ultra-low value of 10 -4 mN/m. Additionally, as the proportion of betaine surfactant increases, the viscosity of the aqueous phase liquid film increases, the rate of thinning of the liquid film slows down, the rate of water release slows down, and the stability of the emulsion increases. Microscopic oil displacement experiments verified that the three mixed systems increase oil washing efficiency through low interfacial tension and emulsification stripping action, thereby increasing the oil displacement mechanism's coefficient. Emulsion flow resistance experiments demonstrated that as the proportion of betaine surfactant increases, the system exhibits better plugging ability. However, macroscopic oil displacement experiments revealed differences in compatibility between different emulsion stability solutions and rocks with different permeabilities. The mixed system of betaine and nonionic surfactants at a ratio of 3:1 exhibits the best emulsification plugging ability in rocks with a permeability of 109mD, while the 1:1 mixed system performs best in rocks with a permeability of 12mD. This holds significant theoretical and practical significance for reservoir development and enhanced production.

We report cyclic growth/retraction phenomena observed for saline droplets placed on the cured PDMS membrane with the thickness of 7.8±0.1 µm floating on pure water surface. Osmotic mass transport across the micro-scaled floating PDMS membrane provided the growth of the sessile saline droplets followed by evaporation of the saline droplets. The observed growth/retraction cycle was reversible. The model of the osmotic mass transfer across the cured PDMS membrane is suggested. The model explains semi-quantitatively the time evolution of a droplet.

Water quality assessment stands as a fundamental step in water resource management. In addition to substances and organisms present in the water, land use and land cover are two factors affecting also water quality. This study analyzed the correlation and influence between water quality and land use and land cover in the Miranda River Basin (MRB) and the natural wetlands in the Pantanal Biome. Using a watershed-wide approach, results suggested that water quality management policies can be considered in terms of sub-basins (smaller planning units). The Water Quality Index (WQI) was considered GOOD or EXCELLENT throughout the MRB. It was observed that the natural wetlands have the capacity to contribute to improve WQI, with reductions in thermotolerant coliforms and turbidity; however, high values were found for thermotolerant coliforms, a temporal increasing trend of biochemical oxygen demand (BOD), and a reduction in dissolved oxygen and total phosphorus. Conversely, it was found in these flooded areas a trend of decrease in dissolved oxygen and an increase in BOD concentrations. Natural wetlands play important hydrological and ecological roles in water quality, storing, removing, and cycling nutrients. They are highly relevant areas for defining watershed management and conservation strategies, environmental protection, and providing ecosystem services.

The construction time of concrete structures in hydraulic tunnels is long, the construction environment is complex, and there are many influencing factors. The requirements for construction quality are high, not only to meet the strength requirements, but also to meet the design requirements of erosion resistance, crack resistance, and seepage resistance according to its specific operating environment. Therefore, evaluating the construction quality of concrete structures in hydraulic tunnels is of great significance. Considering the randomness and fuzziness of factors affecting the construction quality of concrete structures in hydraulic tunnels, this paper proposes a comprehensive evaluation model based on Combined Weighting (CWM) and Uncertainty Measurement Theory (UM). The IAHP method and CRITIC method are used to determine the subjective and objective weights of evaluation indicators, combined weighting is based on the principle of minimum entropy, and the UM method is used to evaluate the construction quality level. Finally, taking a hydraulic tunnel as an example, its construction quality grade is calculated to be III according to the evaluation model proposed in this paper, which matches with the engineering reality, and a comparative study is made with the mixture element topology theory at the same time. It is verified that the evaluation model can scientifically and reasonably evaluate the construction quality level of concrete structures in hydraulic tunnels.

A novel determination method using flow-through cartridge purification and ultra-high-performance liquid chromatography coupled to tandem mass spectrometry (UPLC-MS/MS) was developed for the identification and quantification of 30 mycotoxins (aflatoxin B1, B2, G1, G2, sterigmatocysin, T-2 toxin, diacetoxyscirpenol, roquefortine C, methylergonovine, ergocornine, lysergol, enniatin A, enniatin A1, enniatin B, enniatin B1, beauvericin, deoxynivalenol, 3-acetylDeoxynivalenol, 15-acetylDeoxynivalenol, patulin, verruculogen, neosolaniol, gliotoxin, HT-2 toxin, wortmannin, zearalenone, α-zearalenol, β-zearalenol, α-zearalanol, and β-zearalanol) in feedstuffs. Mycotoxins were extracted from sample by 0.1% formic acid aqueous solution/acetonitrile (16/84 v/v), then purified by a Cleanert® MC clean-up column. As a result, the pigments and other matrices were efficient removed from the sample extract solution. The purified eluate was collected, then evaporated and redissolved by 0.1% formic acid aqueous solution/acetonitrile (70:30 v/v) for UPLC-MS/MS detection. A BEH Shield RP18 chromatographic column was employed for separation of 30 mycotoxins in a total of 14 min. Multiple-reaction monitoring (MRM) mode was applied for qualitative and quantitative analysis, and matrix calibration curves obtained with the external-standard method was used for quantitation of target analytes. Under optimized conditions, the linearity range was from 2 to 1000 ng/g, and the limit of quantification of the developed method was from 2 to 50 ng/g. The recoveries of 30 mycotoxins spiked in urine samples were from 72.0% to 118.5%, and the relative standard deviation was below 20%. The method was also well approved by certified reference sample, and applied on the real feedstuff samples testing successfully.

In this study, high-performance FAU (NaY type) zeolite membranes were successfully synthesized using small-sized seeds of 50 nm, and their gas separation performance was systematically evaluated. Employing nano-sized NaY seeds and an ultra-dilute reaction solution with a molar composition of 80 Na2O: 1Al2O3: 19 SiO2: 5000H2O, the effects of synthesis temperature, crystallization time, and porous support (α-Al2O3 or mullite) on the formation of FAU membranes were investigated. The results illustrated that further extending the crystallization time or increasing the synthesis temperature led to the formation of a NaP impurity phase on the FAU membrane layer. The most promising FAU membrane with a thickness of 2.7 µm was synthesized on an α-Al2O3 support at 368 K for 8 h, and had good reproducibility. The H2 permeance of the membrane was as high as 5.34×10-7 mol/(m2 s Pa), and the H2/C3H8 and H2/i-C4H10 selectivities were 183 and 315, respectively. The C3H6/C3H8 selectivity of the membrane was as high as 46 with a remarkably high C3H6 permeance of 1.35× 10-7 mol/(m2 s Pa). The excellent separation performance of the membrane is mainly attributed to the thin, defect-free membrane layer and relatively wide pore size (0.74 nm).

In a blood purification technique continuous renal replacement therapy called CRRT , a porous hollow-fiber polymeric membrane is exposed to prolonged contact with blood. In that condition, like with any other submerged filtration membrane, hemofilter loses its properties over time and use which results in a rapid decline in flux. The most significant reason for this loss is the formation of a biofilm. Protein, blood cells and bacterial cells attach to the membrane surface in complex and fluctuating processes. Anticoagulation allows for longer patency of vascular access and a longer lifespan of the membrane. Other preventive measures include modification of the membrane itself. In this article, we focused on the role of nanoadditives in the mitigation of bio-fouling. Nanoparticles such as graphene, carbon nanotubes, silica effectively change surface properties towards more hydrophilic, affect pore size and distribution, decrease protein adsorption and damage bacteria cells. As a result, membranes modified with nanoparticles show better flow parameters, longer lifespan and increased hemocompatibility.

Although a slight imbalance between oxidative and antioxidative mediators is part of normal physiology that enables cell aging and the removal of dead cells, burns disturb this equilibrium locally and systemically. Topical burn dressings may attenuate local and systemic oxidative stress and positively influence the post-burn clinical course. This review integrated knowledge regarding the impact of burn dressings on oxidative stress. Using keywords and in-text searches, literature was identified from PubMed, Google Scholar, and Google articles, and studies on local or topical applications of wound dressings and associated oxidative stress were selected. As im-balances between oxidative mediators and antioxidative agents significantly contribute to organ dysfunction and healing disturbance, we investigated oxidative stress on organs, metabolic changes, clinical results, and oxidative parameters influenced by applied dressings. We found positive local and systemic effects of external burn dressings in laboratory and animal tests; however, such studies were rare in humans. Nevertheless, we identified successful cases of semi-occlusive, occlusive, and biologically active dressings that reduce oxidative stress in hu-man burns. In particular, we highlight promising clinical and laboratory results from lac-tate-releasing dressings. Our review provides an invaluable resource for future development and clinical applications of burn dressings.

Gas membrane-based separation is considered one of the furthermost effective technology to address energy efficiency and large footprint challenges. Various classes of advanced materials including polymers, zeolites, porous carbons and metal–organic frameworks (MOFs) were attempted as membranes for gas separation. MOFs, among other porous materials, possess uniquely tunable nature, in which the pore size and environment can be controlled by connecting metal ions (or metal ion clusters) with organic linkers with various functionalities. This feature makes them attractive for thin membrane fabrication, as both diffusion and solubility components of permeability can be altered. It is interesting to notice that numerous reports have addressed the synthesis of different MOFs, fabrication of their corresponding thin films and their applications, nonetheless, relatively limited studies addressed their gas separation application as membranes. In this review, we provide a synopsis of the various MOF-based membranes that were fabricated in the last decade. In this review we propose a short introduction touching on the gas separation membrane technology and we shed light on (i) the various techniques developed for the fabrication of MOF as membranes and (ii) challenges and application for MOF thin film membranes in various important gas separation applications.

Li⁺-conducting polyethylene oxide-based membranes, incorporating the N-butyl-N-methylpyrrolidinium bis(trifluoromethanesulfonyl)imide, are as electrolyte separators for all-solid-state lithium polymer batteries operating at medium-high temperatures. The incorporation of the ionic liquid remarkably improves the thermal, ion-transport and interfacial properties of the polymer electrolyte, which, in combination with the wide electrochemical stability even at medium-high temperatures, allow high current rates without any appreciable lithium anode degradation. Battery tests carried out at 80 °C have shown excellent cycling performance and capacity retention even at high rates, never tackled by ionic liquid-free polymer electrolytes. No dendrite growth onto the lithium metal anode was observed.

Nanoporous membranes promise energy-efficient water desalination. Hexagonal boron nitride (h-BN), like graphene, exhibits outstanding physical and chemical properties, making it a promising candidate for water treatment. We employed Car–Parrinello molecular dynamics simulations to establish accurate modeling of Na+ and Cl- permeation through hydrogen passivated nanopores in graphene and h-BN membranes. In these complex systems the classical potentials cannot properly account for the physics at play. We demonstrate that ion separation works well for the h-BN by imposing a barrier of 0.13 eV and 0.24 eV for Na+ and Cl- permeation respectively, compared to the graphene where the Cl- ion faces a negative barrier of 0.68 eV and is prone toward blockade and Na+ permeation is associated with a slightly negative barrier of 0.03 eV. From the change in the solvation shell, we get the following trend: Na/h-BN > Na/G > Cl/G > Cl/h-BN. We argue that the trend in the permeation barrier changes to Cl-h-BN > Na-h-BN > Na-G > Cl-G due to a combination of several interactions, including the distortion of the water network induced by the ions, the ion-water interaction, and the ion-nanopore interaction. Overall, the desalination performance of h-BN surpasses that of their graphene counterparts.

Spent coffee grounds (SCG) have great potential as a useful, value-added biological material. In this context, activated carbon (AC) was prepared from SCG by an activation process using H3PO4 at 600°C in air and used as an adsorbent for the azo dye AO7, a model molecule for dye colorants found in textile industry effluents. X-ray diffraction, SEM and BET revealed that the AC was predominantly amorphous, consisting of a powder of 20-100 µm particles with mesopores averaging 5.5 nm in pore size. Adsorption kinetics followed a pseudo-second-order law, while the Langmuir model best fitted experimental isotherm data (maximum capacity of 119.5 mg AO7 per AC g). Thermodynamic parameters revealed that adsorption was endothermic and spontaneous. All the characterizations indicated that adsorption occurred by physisorption via mainly - interactions. The best experimental removal efficiency optimized by means of a Box-Behnken design and response surface methodology was 98% for an initial AO7 concentration of 20 mg.L-1 at pH 7.5 with a dose of 0.285 g.L-1 of AC and a contact time of 40 min. These results clearly show that activated carbon prepared from SCG can be a useful material for efficiently removing organic matter from aqueous solutions.

Thin Pd-40%Cu films were obtained by the classical melting and rolling method, magnetron sputtering and modified with nanostructured functional coatings to intensify the process of hydrogen transport. The films were modified by electrodeposition according to the classical method of obtaining palladium black and "Pd-Au nanoflowers" with spherical and pentagonal particles, respectively. The experiment results demonstrated the highest catalytic activity (89.47 mA cm–2), good resistance to CO poisoning and long-term stability of Pd-40%Cu films with a pentagonal structured coating. The investigation of the developed membranes in the hydrogen transport processes in the temperature range of 25-300°C also demonstrated high and stable fluxes up to 475.28 mmol s–1 m–2 (deposited membranes) and 59.41 mmol s–1 m–2 (dense-metal membranes), which turned out to be up to 1.5 higher compared to membrane materials with classic niello. For all-metal modified membranes, the increase in flux was up to 7 times, compared with a smooth membrane made of pure palladium, and for deposited films, this difference was several tens of times. The membrane materials selectivity was also high up to 4419. The developed strategy for modifying membrane materials with functional coatings of a fundamentally new complex geometry can shed new light on the development and fabrication of durable and highly selective palladium-based membranes for gas steam reformers.

To investigate the effect of acidic nanoparticles on proton conductivity, permeability and fuel cell performance, a commercial Nafion® 117 membrane was impregnated with zirconium phosphates (ZrP) and sulfated zirconium (S-ZrO2) nanoparticles. The tensile test, water uptake, methanol crossover, Fourier-transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), Thermal gravimetric analysis (TGA) and Scanning Electron Microscopy (SEM) were used to assess the ca-pacity of nanocomposite membrane to function in a fuel cell. The modified Nafion® membrane obtained the higher water uptake and a lower water content angle than the commercial Nafion® 117 membrane, indicating that it has a greater impact on conductivity. Under strain rates of 40, 30 and 20 mm/min, the nanocomposite membranes demonstrate more stable thermal deterioration and higher mechanical strength, which offers tremendous promise for fuel cell applications. When compared to 0.113 S/cm and 0.013 S/cm, respectively, of commercial Nafion® 117 and Nafion® ZrP membranes, the modified Nafion® membrane with ammonia sulphate acid had the highest proton conductivity of 7.891 S/cm. When tested using a direct single cell methanol fuel cell, it had the highest power density of 183 m. cm-2 which is better than commercial Nafion® 117 and Nafion® ZrP membranes.

In this study, we aim to evaluate how cyclodextrin molecules affect the hydrophilicity and selec-tivity of PVDF membrane. Herein, we prepared PVDF-PVP(1-x) β-CDx membranes, with x rang-ing from 0 to 1 wt%. The membranes were deeply characterized by means of X-ray diffraction (XRD), attenuated total reflectance infrared (ATR-IR), Raman spectroscopies, Thermal gravimet-ric analysis (TGA), Contact angle measurement (CA), scanning electron microscopy (SEM) and atomic force microscopy (AFM). The study unequivocally demonstrates the effectiveness of the addition of β-CD molecules on membranes' structural, morphological, and dielectric properties. Adding 0.25wt% β-CD enhanced hydrophilicity, with CA decreasing from 72.6° to 56° and roughness decreasing from 81 to 29 nm. The PVDF-PVP(1-x) β-CDx membranes were then fully characterized using electrochemical impedance spectroscopy (EIS) to determine their dielectric properties, which clearly showed that the presence of β-CD induced polarization of the mem-brane. The separation of various dyes with different sizes and charges was utilized. These dyes included methylene blue (MB, positive, 0.504 nm), methyl red (MR, neutral, 0.487 nm), rose Bengal (RB, negative, 0.588 nm), and brilliant blue (BB, negative, 0.798 nm). Based on our re-search, we found that the membrane's selectivity is determined by both exclusion factors (such as size and dielectric properties) and inclusion inside the β-CD cage. We found that using alpha-CD instead of beta-CD led to the disappearance of dye inclusion. These findings strongly sug-gest that β-CD molecules can be a viable solution for dye removal from wastewater.

The conformity assessment of products or a measured value with the given standards is carried out based on the global risk of producers and consumers calculation. A product may conform to specifications but be falsely rejected as non-conforming. This is about the producer's risk. If a product doesn't meet the requirements but is falsely accepted as conforming, that poses a risk to the consumer. The conventional approach to risk assessment, which yields only a single numerical value for the global risk of producers and consumers, is naturally extended, and utilized for assessing risk in measurement models with linear regression. The outcomes of the two-dimensional extension, along a moderate scale, are the parabolas with an opening upwards. Risk surfaces were obtained through three-dimensional extension over the area limited by the moderate scale and guard band axes. Four models with different ranges of tolerance intervals were used to test this innovative method of risk assessment in linear regression. The corresponding standard measurement uncertainties are determined by applying a simplified measurement model with the use of comprehensive data on the measurement performance and by determining measurement uncertainty derived from consideration of the functional relationship obtained by linear regression analysis. Models that utilize information from linear regression analysis to determine measurement uncertainty are biased towards risks at the edges of the moderate scale. Testing the model's performances with metrics related to the confusion matrix, such as the F1 score, further substantiated this assertion. The diagnostic odds ratio has been proven to be extremely effective in identifying the curve along the guard band axis, along which the global risks of producers and consumers are at their lowest.

Microfiltration membranes derived from semi-crystalline polymers face various challenges when synthesized through the extrusion–casting technique, including the use of large quantities of polymer, long casting times, and the generation of substantial waste. This study focuses on synthesizing these membranes using spin-casting followed by stretch-induced pore formation. Recycled high-density polyethylene (HDPE) and virgin polyethylene powder, combined with a calcium carbonate filler, were used as the source materials for the membranes. The influence of the polymer-filler ratio with and without stretching on the morphology, tensile strength, and water flow rate was investigated. Optimal conditions were determined, emphasizing a balance between pore structure and mechanical integrity. The permeable membrane possessed a mean pore diameter of 500 nm, exhibited a tensile strength measuring 32 MPa, allowed water to flow at a rate of 19 ml/min, and had a water contact angle of 126°. These membranes effectively eliminated suspended particles from water, with their performance evaluated against that of commercially available membranes. This research outlines a synthesis route for microfiltration membranes tailored to semi-crystalline polymers and their plastic forms, utilizing the spin-casting technique.

The study presents the synthesis and characterization of dual-layer sulfonated polyphenylenesulfone (SPPSu) nanocomposite hollow fiber nanofiltration membranes incorporating titanium dioxide (TiO2) nanoparticles using the phase inversion technique. The newly developed membranes were systematically characterized using advanced tools and methods to evaluate their properties and performance. The study focused on investigating the effects of TiO2 addition in the SPPSu inner layer on pure water permeability, and salt rejection. The nanocomposite hollow fiber nanofiltration membranes exhibited a significant enhancement in pure water permeability, with a three-fold increase compared to the pristine membranes, achieving a flux of 5.4 L/m2h.bar. The addition of TiO2 also led to an improvement in the mechanical properties of the membranes, as evidenced by the increase in the expected tensile strength from 2.4 to 3.9 MPa. To evaluate the salt rejection performance, rejection tests were conducted using a laboratory-scale filtration setup in recycle mode. Aqueous solutions containing different divalent ions, specifically magnesium sulfate (Mg2SO4) and sodium sulfate (Na2SO4) at a concentration of 500 ppm, were used as the feed solution. The modified dual-layer hollow fiber nanocomposite membranes exhibited a maximal rejection of 95% for Mg2SO4, demonstrating their effective separation capabilities for divalent ions. The findings of this study highlight the successful synthesis and characterization of dual-layer SPPSu nanocomposite hollow fiber nanofiltration membranes incorporating TiO2 nanoparticles. The incorporation of TiO2 resulted in improved pure water flux, mechanical strength, and salt rejection performance. These enhanced properties make the developed nanocomposite membranes promising candidates for applications in nanofiltration processes, particularly for the selective separation of divalent ions from aqueous solutions.

In the introductory part of this review, the relevant results of mostly the latest experimental studies on carotenoid absorption and availability in the human body are briefly presented. The subsequent parts summarise such topics as carotenoid carriers, body transport and tissue delivery, before finally reporting on molecular-level studies of carotenoid binding by membrane receptors. The main message of the review is contained in the section describing computational investigations of carotenoid intercalation and dynamic behaviour in lipid bilayers. The relevance of these computational studies lies in showing the direct link between the microscopic behaviour of molecules and the characteristics of their macroscopic ensembles. Furthermore, studying the interactions between carotenoids and lipid bilayers, and certainly proteins, on the molecular- and atomic-level using computational methods facilitates interpretation and explanation of the macroscopic properties of these systems and, hopefully, helps to better understand the biological functions of carotenoids.

Plastic waste constitutes one of the most important sources of pollution worldwide. Despite the growing recycling trend, nowadays there are no effective technologies that can compensate for the continuous increase in plastic production. Polyesters and polyamides are one of the most produced single-use plastics, mainly used in manufacturing textiles and soft drinks bottles. Today, only a very low fraction of these polymers can be recycled. It can be done by exploiting two leading technologies: mechanical and chemical recycling. Mechanical recycling represents, nowadays, the most used industrial application. However, it can treat a very narrow range of waste materials due to the impossibility of removing dyes and the deterioration of mechanical properties due to the incompatibility of different plastic materials. Another critical limit of this recycling technology is the limited number of recycling loops that can be done due to the thermal degradation that occurs during the extrusion process. The second possibility is chemical recycling, which allows the depolymerization of the original product to recover the monomers directly. The main drawbacks are the long reaction times and the many solvents needed to achieve high-purity products. Therefore, chemical recycling is economically feasible, only for big companies that can produce the virgin polymer in situ. In this work, a new technology has been patented. This process is constituted of three main steps. The first one is the distillation-assisted cyclodepolymerization (DA-CDP), introduced as a modification of the CDP process. In this unit, cyclic oligomers together with high molecular weight compounds have been produced. Then, after polymer purification, it is possible to achieve the same molecular weight of the initial polymer in less than 30 minutes, exploiting the ring-opening polymerization (ROP) in the next step.

In this study, a basic study was performed to analyze the seasonal temperature status of a research room in the Global Environment Research Building where ceiling-embedded indoor units are installed to study the room temperature status of the building as well as to improve its thermal environment. In addition, a direction for improvement of the indoor thermal environment in the winter was proposed through a CFD (computational fluid dynamics) simulation and was proven by an additional experiment. Through the results of this study, it appeared that if the ceiling-embedded indoor unit was installed in the small indoor space without considering the thermal vulnerability of its perimeter boundary, the air temperature of the upper part was greatly different from that of the bottom part in the winter. Hence, in this study, as a means to improve it, convectors were installed to minimize the effect of the external thermal environment and angle-controllable air flowing fans were installed to mitigate the stratification distribution. With such result, it was intended to present the essential data for improvement of the thermal environment as well as conservation of heating energy in the winter for buildings by reviewing the use of the ceiling-embedded indoor unit in the future.

The current study presents a computational fluid dynamics model designed to simulate the isolation of 2D graphene components from their dispersion using a microfiltration hollow fiber membrane unit. The model utilizes Navier-Stokes and mass conservation equations to predict the flow and concentration behaviors in the system, and it employs the resistance-in-series approach to couple the fouling of the non-exfoliated graphites in the dispersion to the model. Specifically, the model accounts for the effects of the concentration polarization and cake formation of the fouling component, resulting in the increment of the transmembrane pressure (TMP) of the system. Additionally, we assumed the wettability of polymeric membrane’s inner wall enhances upon fouling by the flat layered structure material, leading to the reduction of the transmemrabe pressure. This approach demosntrates accurate reproduction of the exceptional experimental TMP behavior corresponding to the fouling of the graphite.

The proton conductivity, phase composition and mechanical properties of (1-x)CsH2PO4–x fluoropolymer electrolytes (x-mass fraction, x=0-0.3) have been investigated firstly and discussed. UPTFE and PVDF-based polymers (F2M, F42, SKF26) with the high mechanical properties and thermal stability have been chosen as a fluoropolymer additive. According the XRD data, a monoclinic CsH2PO4 (P21/m) phase is retained in all compositions of the polymer electrolytes studied. The conductivity of (1-x)CsH2PO4-x fluoropolymer in the high-temperature phase decreases by approximately one order of magnitude compared with the pure CsH2PO4 for x~0.15-0.20. The size and shape of CsH2PO4 particles and their distribution have been shown to affect significantly the proton conductivity and mechanical properties of the membranes. The thin-film composite systems were produced by various methods of the obtaining salt particles, their mixing and applying to a polymer matrix. The uniform distribution of particles in the polymer systems with the size of ~300 nm was achieved by a pretreatment of the suspension in a bead mill. CsH2PO4-based mechanically strong membranes with the thickness ~50–100 μm were obtained for the soluble fluoropolymers (F2M, F42, SKF26). With an increase in the mass fraction of the polymer the ability of the membranes to resist the plastic deformation and the mechanical strength increases and comparable to the best low temperature membranes. The proton-conducting membranes (1-x)CsH2PO4 – x fluoropolymer with the optimal combination of the conductivity, mechanical and hydrophobic properties are promising for use in solid acid fuel cells.

High porosity and mass transport properties of microfiltration polymeric membranes benefits nutrients supply to cells when used as scaffolds in interstitial perfusion bioreactors for tissue engineering. High nutrients transport is assumed when pore size and porosity of the membrane are in the micrometric range. The present work demonstrates that the study of membrane fouling by proteins present in the culture medium, though not done usually, should be included in the routine testing of new polymer membranes for this intended application. Two poly(ε-caprolactone) microfiltration membranes presenting similar average pore size (~0.7µm) and porosity (>80%) but different external surface porosity and pore size have been selected as case study. The present work demonstrates that a membrane with lower surface pore abundance and smaller external pore size (~0.67 µm), combined with adequate hydrodynamics and tangential flow filtration mode is usually more convenient to guarantee high flux of nutrients. On the contrary, having large external pore size (~1.70µm) and surface porosity would incur in important internal protein fouling that could not been prevented with the operation mode and hydrodynamics of the perfusion system. Additionally, the use of glycerol in the drying protocols of the membranes might cause plasticization and a consequent reduction of mass transport properties due to membrane compaction by the pressure exerted to force perfusion. Therefore, preferentially, drying protocols that omit the use of plasticizing agents are recommended.

The increasing global concern over plastic waste and its environmental impact has led to a growing interest in the development of sustainable packaging alternatives. This study focuses on the innovative use of expired dairy products as a potential resource for producing edible packaging materials. Expired dairy products, which are typically discarded, contribute to food waste and environmental pollution. By modifying these products to packaging materials, a dual-purpose solution addressing both waste reduction and sustainable packaging is evaluated. Expired milk and yogurt were selected as the primary raw materials due to their protein and carbohydrate content. The extracted casein was combined with various concentrations of chitosan while in some cases glycerol was used. The materials were characterized with attenuated total reflectance-Fourier transform infrared (ATR-FTIR) spectroscopy and X-ray analysis (XRD) to examine the interactions between the components of the formed binary blend. Scanning electron microscopy (SEM) was used to evaluate the surface morphology of the blends, while dynamic mechanical analysis (DMA) and tensile experiments were conducted to study the thermomechanical properties of the materials. Barrier properties, including water vapor transmission (WVTR) and oxygen permeability (OTR), were measured to assess the materials' potential to preserve food freshness. The findings reveal that expired dairy-based edible packaging materials exhibit promising mechanical properties, comparable to conventional plastic packaging. The barrier properties and especially the zero oxygen permeability of the membranes, indicate that these materials have the potential to effectively protect food products from external factors that could compromise quality and shelf life. The materials show encouraging signs of eco-friendliness, with a notable reduction in environmental persistence compared to conventional plastic packaging.

Although 4Ce4YSZ has high corrosion resistance, it faces challenges concerning sinterability and ionic conductivity. Therefore, we studied destabilization behavior caused by corrosion and oxygen vacancy ordering according to ZnO doping. The powders of (4Ce4YSZ)1-x(ZnO)x (x=0.5, 1, 2, 4 mol%) were synthesized through the sol-gel method. With the addition of ZnO, the cubic phase increased, and secondary phases were not observed. The (111) peak showed a higher angle shift in ZnO-doped 4Ce4YSZ compared to 4Ce4YSZ, and TEM-SAED revealed a reduction in the spacing of the (011)t plane, suggesting lattice contraction due to the substitution of the smaller Zn2+ (60 Å) for Zr4+ (84 Å) in the lattice. The local atomic structure analysis was conducted using EXAFS to investigate the oxygen vacancy ordering behavior. Zr K-edge Fourier-transform data revealed a decrease in the Zr-O1 peak intensity with an increasing amount o ZnO doping, indicating an increase in oxygen vacancies. The Zr-O1 peak position shifted to the right, leading to an increase in the Zr-O1 interatomic distance. In the Y K-edge Fourier-transform data, the Y-O1 peak intensity did not decrease, and there was little variation in the Y-O1 interatomic distance. These results suggest that the oxygen vacancies formed due to ZnO doping are located in the neighboring oxygen shell of Zn, rather than in the neighboring oxygen shells of Y and Zr. Impedance measurements were conducted to measure the conductivity, and as the amount of ZnO doping increased, the total conductivity increased, while the activation energy decreased. The increase in oxygen vacancies by ZnO doping contributed to the enhancement of conductivity and it is considered that these created oxygen vacancies did not interact with Zn2+ and did not form defect associations. Fluoride-based molten salts were introduced to the specimens to assess corrosion behavior in a molten salt environment. Yttrium depletion layers (YDLs) were formed on the surfaces of all specimens due to the leaching of yttrium. However, Ce remained relatively stable at the interface according to EDS line scans, suggesting a reduction in the phase transformation (cubic, tetragonal to monoclinic) typically associated with yttrium leaching in YSZ.

Group IV phospholipase A₂α (cPLA₂α) regulates the production of prostaglandins and leukotrienes via the formation of arachidonic acid from membrane phospholipids. The targeting and membrane binding of cPLA₂α to the Golgi involves the N-terminal C2 domain whereas the catalytic domain produces arachidonic acid. Although most studies of cPLA₂α concern its catalytic activity, it is also linked to homeostatic processes involving the generation of vesicles that traffic material from the Golgi to the plasma membrane. Here we investigate how membrane curvature influences the homeostatic role of cPLA₂α in vesicular trafficking. The cPLA₂α C2 domain is known to induce changes in positive membrane curvature, a process which is dependent on cPLA₂α membrane penetration. We show that cPLA₂α undergoes C2 domain-dependent oligomerization on membranes in vitro and in A549 cells. We found that the association of the cPLA₂α C2 domain with membranes is limited to membranes with positive curvature, and enhanced C2 domain oligomerization was observed on vesicles ~50 nm in diameter. We demonstrated that the cPLA₂α C2 domain generates cholesterol enriched Golgi-derived vesicles independently of cPLA₂α catalytic activity. Our results therefore provide novel insight into the molecular forces that mediate C2 domain-dependent membrane localization in vitro and in cells.

The adulteration of goat milk powder occurs frequently, cattle-derived and soybean-derived ingredients are common adulterants in goat milk powder. However, simultaneously and rapidly detecting cattle-derived and soybean-derived components is still a challenge. high throughput and efficient screening method for adulteration detection is need. In this study, a rapid method was developed to detect the adulteration of common cattle-derived and soybean-derived components simultaneously in goat milk powder by combining the CRISPR/ Cas12a system with recombinant polymerase amplification (RPA). A dual DNA extraction method was employed, primers and crRNA for dual detection were designed and screened, and a series of condition optimizations were carried out in this experiment. The optimized assay can rapidly detect cattle-derived and soybean-derived components in 40 min. The detection limits of both cattle-derived and soybean-derived components were 1% (w/w) for the mixed adulteration models. The established method was applied into a blind survey of 55 commercially available goat milk powder products. The results showed that 36.36% of the samples contained cattle-derived or soybean-derived ingredients, which revealed the noticeable adulteration situation in the goat milk powder market. This study realizes a fast flow of dual extraction, dual amplification and dual detection of cattle-derived and soybean-derived components in goat milk powder for the first time. It can be used for high-throughput and high-efficiency on-site primary screening of goat milk powder adulterants, and provide a technical reference for combating with food adulteration.

Self-healing ceramic composites are promising smart materials for high-temperature applications. To better understand their behaviors under service conditions, numerous studies have been performed both experimentally and numerically, and kinetics parameters such as activation energy and frequency factor are reported to be indispensable for investigating healing phenomena. Here, we propose a method for determining the kinetic parameters of self-healing ceramic composites based on the oxidation kinetics model of strength recovery. These parameters are determined by an optimization method using experimental strength recovery data under various healing temperatures and times and microstructural features on the fractured surfaces. Alumina and mullite matrix-based self-healing ceramic composites, such as Al2O3/SiC, Al2O3/TiC, Al2O3/Ti2AlC (MAX phase), and mullite/SiC, were selected as target materials. The theoretical strength recovery behaviors of the cracked specimens obtained from the determined kinetic parameters were compared with the experimental results. The determined parameters are within the previously reported range, and the predicted strength recovery behaviors are reasonably agreed with the experimental values. The proposed method can also be applied to other self-healing ceramics with matrices reinforced with different healing agents to evaluate oxidation rate, crack healing rate, and theoretical strength recovery behaviors for designing self-healing materials used in high temperature applications. Furthermore, the healing ability of composites can be fairly discussed regardless of the type of strength recovery test.

Fouling by activated sludge in membrane bioreactor (MBR) processes for wastewater treatment can be reduced using several strategies such as backflushing, relaxation, and chemical cleaning. Some proprietary systems such as Avanti’s RPU-185 Flexidisks MBR use novel circular rotating, flat sheet membranes to assist in limiting this fouling. An attempt has already been made to model this novel rotating fouling process by developing a simulation model based on first principles and traditional fouling mechanisms. In order to directly compare the potential benefits of rotational MBR system, a follow-up study was carried out using Avanti’s newly developed static (non-rotating) Flexidisks MBR system. This new process uses the same proprietary and patented membrane modular arrangement as used in the circular rotational unit, but is configured instead as a static square-shaped unit which is in-line with the more traditional and popular format used for submerged flat sheet MBR systems. During this study, the results from operating the static pilot unit were simulated and modelled using a standard fouling model coupled with a viscosity to mixed liquor relationship model. These results were then compared with those obtained from running the rotating MBR model however with rotational switching functions turned off and rotational parameters set to a static mode. This comparison was done to ascertain whether the basic premise of the developed rotational model was sound in empirical terms when compared to a standard MBR flux model. The study concluded that relatively good agreement was reached between the two types of models, thus vindicating the usage of a complex rotational MBR model. Follow on studies will now compare results from the rotating MBR system using rotational models developed by other researchers to ascertain the effectiveness rotating MBR modelling approach.

A cell filtration platform that affords accurate size separation and minimizes fouling was developed. The platform features an ultra-thin porous membrane (UPM) filter, a pumping head for backflushing (PHB), and cell size measurement (CSM) software. The UPM chip is an ultrathin free-standing membrane with a large window area of 0.68 mm2, a pore diameter of 5 to 9 μm, and a thickness of less than 0.9 μm. The PHB prevents filter fouling. The CSM software analyzes the size distributions of the supernatants and subnatants of isolated cells and presents the data visually. The D99 particle size of cells of the chronic myeloid leukemia (CML) line K562 decreased from 22.2 to 17.5 μm after passage through a 5-μm filter. K562 cells could be separated by careful selection of the pore size; the recovery rate attained 91.3%. The method was compared to conventional blocking models by evaluating the mean square errors (MSEs) between the measured and calculated filtering volumes. The filtering rate was fitted by a linear regression model with a significance that exceeded 0.99 based on the R2 value. The platform can be used to separate various soft biomaterials and affords excellent stability during filtration.

Dye wastewater containing bisphenol A (BPA) and dyes as pollutants have not been adequately studied. Our previous study revealed that thermoplastic polyurethane (TPU) nanofiber membranes (NFMs) modified by the addition of polyethyleneimine (PEI) and polydopamine (PDA) satisfactorily adsorb dyes. Herein, we first optimized the synthesis conditions for such membranes, noting a PEI:PDA monomer ratio of 2:2 and a deposition time of 48 h to be optimal. Experiments using these membranes revealed that binary systems containing BPA and the dyes (Congo red (CR), Eosin yellow (EY), or sunset yellow (SY)) exhibit three adsorption behaviors. CR and BPA compete with each other for adsorption sites, decreasing the maximum adsorption capacity (Qmax) for CR 208.3 mg/g (in a monomeric system) to 182.4 mg/g, whereas for BPA, it decreased from 26.7 to 22.8 mg/g. The adsorption rates for CR and BPA decreased from 0.002 min−1 and 0.331 min−1 in the monomeric systems to 8.37 × 10−4 min−1 and 0.072 min−1, respectively, in the binary CR–BPA system, exhibiting antagonistic effects. When EY and BPA coexist, Qmax for EY increased from 60.0 (monomeric) to 71.9 mg/g, whereas that for BPA increased from 35.6 to 43.2 mg/g, showing a synergistic effect due to the possible bridging effect. The adsorption sites for SY and BPA are independent of each other. Thus, PDA/PEI TPU NFMs exhibit the potential for removal of dye–BPA composites, whereas binary systems containing BPA with different dyes are adsorbed differently.

A set of aromatic copolyimides was obtained by reaction of 4,4′-(hexafluoroisopropylidene) diphthalic anhydride (6FDA), and mixtures of the diamines 1,4-bis(4-amino-2-trifluoromethylphenoxy)-2,5-di-tert-butylbenzene (CF3TBAPB) and 3,5-diamino benzoic acid (DABA). These polymers were characterized and compared with the homopolymer derived from 6FDA and CF3TBAPB. All copolyimides showed high molecular weight values and good mechanical properties. The presence of carboxylic groups in these copolymers allowed their cross-linking by reaction with 1,4-butanediol. The crosslinked polymer films were extensively characterized and it was observed that the degree of crosslinking was low in the copolyimides possessing a small number of carboxyl groups. The degradation temperature of these crosslinked copolyimides was lower than their corresponding non-crosslinked ones. Glass transition temperatures were higher than 260 oC, showing the non-crosslinked copolyimides the highest values. Young moduli of these crosslinked showed values higher than 1.9 GPa, and slightly lower elongation at break when compared with the precursor copolyimides. All copolyimides (precursor, and crosslinked ones) films could be tested as gas separation membranes. It was seen that CO2 permeability values were around 100 barrer, having better selectivity than that of the homopolymer. Moreover, the plasticization resistance of the crosslinked material having a large number of carboxylic groups was excellent.

Herein, we report results of the study of the composite ferroelectric scaffolds based on vinylidene fluoride-tetrafluoroethylene copolymer (VDF-TeFE) and polyvinylpyrrolidone (PVP) produced by electrospinning and their application as a wound-healing material. The physicochemical properties of ferroelectric composite polymer scaffolds depending on the content of PVP (in the range from 0 to 50 wt %) including morphology, composition and crystalline structure were studied. The cytotoxicity of materials and the proliferative activity of cells during their cultivation on the surface of formed scaffolds are reported. It has been found that the optimal PVP content in the VDF-TeFE composite scaffolds is 15 wt%. On a model of a full-thickness contaminated wound in vivo, it was shown that piezoelectric scaffolds based on VDF-TeFE copolymer containing 15 wt% PVP provide better wound healing results in comparison with standard gauze dressings impregnated with a solution of an antibacterial agent.

The involved components of formulated blending, CNF and CuO NPs, were individually obtained by using a biorefinery strategy for agricultural waste valorization together with an optimized chemical precipitation, assisted by ultrasounds. The optimization of synthesis parameters for CuO NPs have avoided the presence of undesirable species which usually requires of later thermal treatment with associated costs. The aerogels-based structure, obtained by conventional freeze-drying, acted as 3D support for CuO NPs providing a good dispersion within the cross-linked structure of the nanocellulose and facilitating direct contact of the antibacterial phase against undesirable microorganisms. All samples showed a positive response against Escherichia coli and Staphylococcus aureus. An increase of the antibacterial response of the aerogels, measured by agar disk diffusion test, has been observed with the increase of CuO NPs incorporated, obtaining width of the antimicrobial “halo” (nwhalo) from 0 to 0.6 and 0.35 for S. aureus and E. coli, respectively. Furthermore, the aerogels have been able to deactivate S. aureus and E. coli in less than 5 hours when the antibacterial assays have been analyzed by broth dilution method. From CNF-50CuO samples, an overlap nanoparticles effect produced a decrease of the antimicrobial kinetic.

NDBs were fabricated from gum arabic (GA) and polyvinyl alcohol (PVA) in different ratios using novel techniques (casting, dehydration, and peeling). The GA/PVA blends were cast with a novel vibration-free horizontal flow (VFHF) technique, producing membranes free of air bubble defects with a homogenous texture, smooth surface, and constant thickness. The casting process was achieved on a self-electrostatic template (SET) made of poly-(methyl methacrylate), which made peeling the final product membranes easy due to its non-stick behavior. After settling of the cast membranous blind, sheets were dried using nanometric dehydration under a mild vacuum stream using a novel stratified nanodehydrator (SND) loaded with P2O5. After drying the TBM, the dry, smooth membranes were peeled easily without scratching defects. The physicochemical properties of the NDBs were investigated using FTIR, XRD, TGA, DTA, and AFM to ensure that the novel techniques did not distort the product quality. The NDBs retained their virgin characteristics, namely, their chemical functional groups (FTIR results), crystallinity index (XRD data), thermal stability (TGA and DTA), and ultrastructural features (surface roughness and permeability), as well as their microbial biodegradation ability. Comparing the two TBM’ s precursors, PVA had a higher crystallinity index (CI), more mass loss at higher temperatures, greater thermal stability due to higher heat resistance, and a higher clearance of surface roughness due to its large particle size (PS), as well as its higher permeability parameters, namely pore diameter (PD) and void volume (VV), than those for GA. Accordingly, increasing the PVA allocation in the bioplastic blends can enhance their properties except for mass loss, whereby increasing the GA allocation in the TBM blend reduces its mass loss at an elevated temperature. In addition, there is no statistical difference between the NDBs and ordinary air-dried NDBs in PS, PD, and VV, indicating that the novel procedures used did not distort their parent properties examined, as well as their ability for biodegradation. In comparison to control samples, the separated bacteria and fungus destroyed the NDBs. Pseudomonas spp. and Bacillus spp. were the two main strains of isolated bacteria, and Rhizobus spp. was the main fungus. The nanodehydration method gave the best solution for the prompt drying of water-based biopolymers free of manufacturing defects, with simple and easily acquired machinery required for the casting and peeling tasks, in addition to its wonderful biodegradation behavior when buried in wetted soil.

The review is devoted to the physical, chemical and technological aspects of the breath-figures self-assembly process. Main stages of the process and the impact of the polymer architecture and physical parameters of the breath-figures self-assembly on the eventual pattern are covered. The review is focused on the hierarchy of spatial and temporal scales inherent for the breath-figures self-assembly. Multi-scale patterns arising from the process are addressed. The characteristic spatial lateral scales of patterns vary from nanometers to dozens of micrometers. The temporal scales of the process span from micro-seconds to seconds. The qualitative analysis performed in the paper demonstrates that the process is mainly governed by the interfacial phenomena, whereas the impact of inertia and gravity is negligible. Characterization and applications of polymer films manufactured with breath-figures self-assembly are discussed.

Porous α-Al2O3 ceramics is a highly demanded material for multitude applications such as filters, substrates, biomedicine materials, etc. Despite the availability of the raw materials, a challenge of their technology is in a high energy budget caused by the sintering above 1500 °C. For a cold sintering processing (CSP) of ceramics, the lowering of α-Al2O3 sintering temperature is one of the most urgent challenges at the background of its rapid development. The current paper for the first time demonstrates the solution of the mentioned problem by the CSP of α-alumina ceramics in a presence of pure water as a transient liquid. The manufactured materials were examined by XRD analysis; the evolution of their microstructures during the CSP was revealed by SEM, and the porosity evaluated by the Archimedes method. The ceramics with an open porosity up to 36 % was produced at 380-450 °C, 220 MPa in 30 min. An increase in the pressure was found to impede α-Al2O3 formation from γ-AlOOH. The development of the microstructure was discussed within the frameworks of the dissolution-precipitation model and the homogenous nucleation. The results of the SEM study pointed to the coalescence of γ-AlOOH grains during the CSP.

Two new dimacrolide sesquiterpene pyridine alkaloids (DMSPAs), dimacroregelines A (1) and B (2), were isolated from the stems of Tripterygium regelii. The structures of both compounds were characterized by extensive 1D and 2D NMR spectroscopic analyses, as well as HRESIMS data. Compounds 1 and 2 are two rare DMSPAs possessing unique 2-(3′-carboxybutyl)-3-furanoic acid units forming the second macrocyclic ring, representing the first example of DMSPAs bearing an extra furan ring in their second macrocyclic ring system. Compound 2 showed inhibitory effects on the proliferation of human rheumatoid arthritis synovial fibroblast cell (MH7A) at a concentration of 20 μM.

The role of foods is shifting from focusing on the provision of energy and basic nutrients to also include bioactive compounds that prevent the development of chronic age-related diseases. Mi-croalgae offer a source of nutritional compounds with important health effects, and have the po-tential for production of health-promoting products, without increasing agricultural land use and negatively impacting the environment. Here we investigate the health effects of microalgal ex-tracts with high levels of the colourless carotenoid phytoene. Phytoene is widely available from dietary sources and can be detected across different tissues in the human body. However, it is usually regarded as a precursor for the synthesis of other carotenoids, rather than a bioactive molecule. We utilised the model organism C. elegans to show that phytoene-rich extracts from Chlorella sorokiniana and Dunaliella bardawil have anti-ageing properties. The extracts protect against oxidative damage and amyloid-β42 proteotoxicity (a major pathology of Alzheimer's disease), and extends lifespan. We show that pure phytoene also has these anti-ageing effects, suggesting that phytoene is a bioactive molecule with positive effects on ageing and longevity.

Pyrolysis is a thermochemical conversion process designed for biomass decomposition in an oxygen-free environment. It typically operates within a temperature window of 200 to 800°C and generates various byproducts, including gases, liquid fractions (both aqueous and organic) such as bio-oil, and solids like char. Bio-oil is a significant product of pyrolysis. It is characterised by a complex blend of organic compounds. The acidic nature of bio-oil primarily originates from volatile acids, such as acetic acid. The recovery of acetic acid from bio-oil facilitates the use of the extracted substance as a precious resource, hence enhancing its significance in the framework of a circular bioeconomy. Acetic acid finds widespread application in manufacturing commercially important chemicals like vinyl acetate monomers and formulating phytosanitary products due to its inherent herbicidal and antifungal properties. However, to be used, acetic acid has to be separate from the raw bio-oil. Separation methodologies, including nanofiltration and reverse osmosis, demonstrate potential in recovering acidic constituents from bio-oil due to their high selectivity and effective system management. This article offers a concise review about acetic production from lignocellulosic biomass from pyrolysis and its recovery through various membrane separation processes.

Although a slightly radioactive element, thorium is considered very toxic because its various species, which reach the environment, can constitute an important problem for the health of the population. The present paper aims to expand the possibilities of using membrane processes in the removal, recovery and recycling of thorium from industrial residues reaching the municipal waste processing platforms. The paper includes a short introduction on the interest shown for this element, a weak radioactive metal, followed by highlighting of some common (domestic) uses. In a distinct but concise part, the bio-medical impact of thorium is presented. The classic technologies for obtaining thorium are concentrated in a single schema, and then the speciation of thorium is presented with an emphasis on the formation of hydroxo-complexes and complexes with common organic reagents. The determination of thorium has been highlighted both on the basis of its radioactivity, but especially through methods that call for extraction followed by an established electrochemical, spectral or chromatographic method. Membrane processes are presented based on the electrochemical potential difference, rapidly presenting barro-membrane processes, electrodialysis, liquid membranes and hybrid processes. A separate sub-chapter is devoted to proposals and recommendations for the use of membranes in order to achieve some progress in urban mining for the valorization of thorium.