This article introduces a new MfEIT UDESC Mark I system, which consists of a 32-electrode setup featuring a modified Howland current source, low cost, portable and non radiation. The system is capable of reconstruction of electrical conductivity tomographic images at a rate of 30.624 frames per second and about 5 minutes for imaging. The current source employs 0.5 mA, adjacent current application pattern with frequencies ranging from 10 kHz to 1 MHz. The article outlines the hardware, firmware, and software design specifications, which include the design of the current source, calibration procedures, and image reconstruction process. Tomographic images of conductivity were reconstructed in ex vivo healthy pig lungs and those with pneumonia, as a proof of concept for future applications in live pigs. The high spectral power density, combined with real-time system calibration provides clinical advantages in veterinary medicine. The goal is to identify lung areas affected by Mycoplasma hyopneumoniae in pigs, through the analysis of electrical conductivity difference, offering a valuable tool to assist veterinarians for to obtain images of respiratory diseases. The reconstruction method (GREIT) was evaluated with experimental data and It was compared with the Gauss-Newton and Total Variation methods, where GREIT proved to be superior.

Electrical impedance tomography (EIT) can monitor the real-time hemodynamic state of a conscious and spontaneously breathing patient noninvasively. However, cardiac volume signal (CVS) extracted from EIT images has a small amplitude and is sensitive to motion artifacts (MAs). This study aimed to develop a new algorithm to reduce MAs from the CVS for more accurate heart rate (HR) and cardiac output (CO) monitoring in patients undergoing hemodialysis based on the source consistency between the electrocardiogram (ECG) and the CVS of heartbeats. Two signals were measured at different locations on the body through independent instruments and electrodes, but the frequency and phase were matched when no MAs. As the number of motions per hour (MI) increased over 30, the proposed algorithm had a correlation of 0.83 and a precision of 1.65 beats per minute (BPM) compared to the conventional statical algorithm of a correlation of 0.56 and a precision of 4.04 BPM. For CO monitoring, the precision and upper limit of the mean ∆CO were 3.41 and 2.82 liters per minute (LPM), respectively, compared to 4.05 and 3.82 LPM of the statistical algorithm. The developed algorithm could reduce MAs and improve HR/CO monitoring accuracy and reliability, particularly in high-motion environments.

Background: Electrical Impedance Tomography (EIT), combined with variable ventilation strate-gies and Artificial Intelligence (AI), is poised to revolutionize critical care by transitioning from reactive to predictive approaches. This integration aims to enhance patient outcomes through personalized interventions and real-time monitoring. Methods: This narrative review explores the principles and applications of EIT, variable ventilation, and AI in critical care. EIT’s impedance sensing creates dynamic images of internal physiology, aiding in the management of conditions like Acute Respiratory Distress Syndrome (ARDS). Variable ventilation mimics natural breathing variability to improve lung function and minimize ventilator-induced lung injury. AI enhances EIT through advanced image reconstruction techniques, neural networks, and digital twin technology, offering more accurate diagnostics and tailored therapeutic interventions. Conclu-sions: The confluence of EIT, variable ventilation, and AI represents a significant advancement in critical care, enabling a predictive, personalized approach. EIT provides real-time insights into lung function, guiding precise ventilation adjustments and therapeutic interventions. AI inte-gration enhances EIT's diagnostic capabilities, facilitating the development of personalized treatment plans. This synergy fosters interdisciplinary collaborations and sets the stage for in-novative research, ultimately improving patient outcomes and advancing the future of critical care.

The article presents a non-destructive test system based on electrical impedance tomography for monitoring flood embankments. The technology of cyber-physical systems and the Internet of Things with the use of electrical impedance tomography enables real-time monitoring of flood embankments. This solution provides a visual analysis of damage and leaks, which allows for quick and effective intervention and possible prevention of danger. A dedicated solution based on the IT structure, dedicated laboratory models and a dedicated measurement system with various types of sensors and machine learning algorithms for image reconstruction has been developed. The system includes specialized intelligent devices for tomographic measurements. The application contains the analysis of anomalies occurring in the structure of the object as a result of damage or danger and breaking the shaft during the flood. The presented solution enables ongoing monitoring of objects by collecting measurement results, forecasts and simulations. The main advantage of the proposed system is the spatial ability to analyse shafts, high accuracy of imaging and high speed of data processing. The use of tomographic techniques in conjunction with image reconstruction algorithms allow for non-invasive and very accurate spatial assessment of humidity and damages of flood embankments. The presented results show the effectiveness of the presented research.

Understanding and predicting damage progression within thin plain-woven CFRP components is an essential issue for scheduling maintenance intervals and structural inspections, and typically require extensive test series. However, uncertainties always remain and result in conservative design and unnecessary downtimes due to the repeated inspections of a healthy structure. SHM can be used to reduce these uncertainties, as it allows to evaluate the condition of a mechanical structure during operation. Numerous SHM methods are developed , that achieve different levels of damage identification but are often investigated at small coupons with non-realistic structural damages and loading conditions on both, structure and sensor. The present research investigates the electrical impedance tomography (EIT) featuring an elastoresistive thin-film sensor to evaluate damage that propagates from a circular hole in a large plate under cyclic tensile-tensile multi-block loading. Applied fatigue loads were increased multiple times up to a total number of two million cycles. During the loading damage initiated at the hole and continuously propagated into the plate. Repeated EIT evaluations of the applied sensor and validating evaluations by means of digital image correlation clearly revealed the robustness of the hardware and the potential of the SHM method for damage evaluation of plain-woven CFRP components.

Diesel is consistently a very popular fuel for internal combustion engines. Its consumption in the European Union has been rising over recent years, as has the number of engines increasingly sensitive to fuel contamination. One of the most important parameters affecting diesel quality is water content. Although its exceedances of the standard’s permissible amount are not common, they carry the risk of serious damage to expensive, modern fuel injection systems. Current methods of measuring water content require both specialised personnel and equipment, as well as transporting the sample to a suitable laboratory. The research presented in this paper was aimed at verifying whether it would be possible to test the moisture content of diesel using impedance spectroscopy. Once refined, such measurement method could be used in situ. Analysing the properties of diesel is challenging, mainly because many types of the fuel are sold, the chemical composition of which is always a well-guarded manufacturer’s secret. The experimental results obtained on many types of commercially available diesel show that it is possible to use impedance spectroscopy to estimate the water content of different types of diesel fuel. The measurement accuracy achieved makes it possible to detect approaching or exceeding the permissible water content.

Background: The modified Duke index derived from coronary computed tomography angiography (CCTA) was designed to predict cardiovascular outcomes based on the severity of coronary ste-nosis. However, it does not take into consideration the presence or severity of peri-coronary in-flammation. The peri-coronary fat attenuation index (FAI) is a novel imaging marker determined by CCTA which reflects the degree of inflammation in the coronary tree in patients with coronary artery disease. Purpose: To assess the association between the modified Duke index assessed by CCTA, cardiovascular risk factors and peri-coronary inflammation in the coronary arteries of pa-tients with coronary artery disease. Methods: One hundred seventy-two patients who underwent CCTA for typical angina were assigned into two groups based on the modified Duke index: group 1 – patients with low index ≤ 3 (n=107) and group 2 – patients with high index > 3 (n=65). Demo-graphic, clinical and CCTA data were collected for all patients, and FAI analysis of coronary in-flammation was performed. Results: Patients with increased values of the modified Duke index were significantly older compared to those with a low index (61.83 ± 9.89 vs. 64.78 ± 8.9; p = 0.002). No differences were found between the two groups in terms of gender distribution, hypertension, hypercholesterolemia or smoking history (all p > 0.5). The FAI score was significantly higher in patients from group 2, who presented a significantly higher score of inflammation compared to the patients in group 1, especially at the level of the right coronary artery (FAI score 20.85 ± 15.80 vs. 14.61 ± 16.66; p = 0.01 for the right coronary artery, 13.85 ± 8.04 vs. 10.91 ± 6.5; p = 0.01 for the circumflex artery, and 13.26 ±10.18 vs. 11.37 ± 8.84; p = 0.2 for the left anterior descending artery). CaRi-Heart® analysis identified a significantly higher risk of future events among patients with a high modified Duke index (34.84 % ± 25.86 % versus 16.87 % ± 15.80 %; p

We present an idea how to use long-wavelength multi-wavelength radio continuum observations of spiral galaxies to isolate magnetic structures which were previously accessible from short-wavelength observations only. The approach is based on the RM-synthesis and 2D continuous wavelet transform. Wavelet analysis helps to recognize a configuration of small-scale structures which are produced by Faraday dispersion. We find that these structures can trace galactic magnetic arms for the case of the galaxy NGC 6946 observed at $\lambda = 17 \div 22$~cm. We support this interpretation by an analysis of a synthetic observation obtained using a realistic model of a galactic magnetic field.

Sarcopenia becomes more common with age, being most prevalent among elderly individuals. According to the EWGSOP, muscle mass is one of the criteria for the evaluation of sarcopenia. The main methods for evaluating muscle mass are CT, MRI, and DXA, but these methods are difficult to apply in the field due to equipment costs, radioactivity, and lack of portability. BIVA and PhA are alternative approaches for assessing somatic cell mass and volume and do not require predictive equations. These variables are clinically relevant parameters that indicate cell health, especially cell membrane integrity and cell function. This study in sarcopenic and nonsarcopenic elderly volunteers aimed to determine the BIVA distribution pattern among individual sarcopenia patients; to evaluate the relationship between PhA and muscle strength, muscle quality, and physical function; and to find any correlates of PhA. The sample comprised 134 free-living elderly individuals of both sexes aged 69–91 years. Anthropometric parameters, grip strength, DXA findings, BIA results, and physical performance (the 6-meter walk test) were measured. Impedance vector distributions were evaluated in sarcopenia patients and healthy elderly individuals using BIVA. According to the AWGS criteria, sarcopenia was diagnosed according to DXA findings, grip strength and physical performance test results. Group differences were evaluated using the t test, Mann‒Whitney U test, and Hotelling's T2 test. Correlation analysis was performed to identify variables significantly associated with PhA. Linear regression analysis was performed to determine whether PhA was associated with muscle strength, muscle quality and physical function. BIVA detected a significant difference between the sarcopenia and non-sarcopenia groups (both sexes) due to higher R/H values and lower phase angles in a few individuals, whereas Xc/Ht values did not differ between the two groups. The sarcopenia group had a significantly lower PhA than the non-sarcopenia group among both males (p<0.01) and females (p<0.05). PhA was significantly correlated with age, ASM, HGS, and muscle quality in both sexes and significantly correlated with ASM/Ht2 and physical performance in males. PhA was a significant indicator of muscle strength in both males (β = 2.6; p<0.01) and females (β = 3.4; p<0.01), a significant indicator of muscle quality in both males (β = 0.07; p<0.05) and females (β = 0.17; p<0.01), and a significant indicator of physical performance in males (β = 0.3; p<0.01). BIVA can detect changes in muscle mass in individuals with sarcopenia and is a practical method for the assessment of sarcopenia in the field. PhA is a good indicator of muscle strength, muscle quality and physical performance (in males). These methods can help diagnose sarcopenia in elderly individuals with reduced mobility.

A hypothesis that the generally accepted value of the LiPON conductivity should be attributed to the absorption and displacement currents is substantiated. The reason is a small contribution of the drift current due to field screening by the electric double layer. The basis for this assumption is the measurement of the LiPON absorption capacitance, according to which its dielectric constant is about 106. An alternative equivalent circuit containing a non-ideal absorption element is proposed and its impedance is calculated. It is shown that the Bode diagrams of the alternative circuit well approximate the experimental curves. Parameters and the magnitude of electric field screening are calculated basing on proposed model of a double electric layer. Considering the screening effect, the drift conductivity of LiPON is obtained, which value is in good agreement with the data on lithium concentration and mobility.

Epilepsy is a chronic neurological disorder characterized by recurring seizures resulting from abnormal neuronal hyperexcitability. In the case of pharmacoresistant epilepsy requiring resection surgery, identifying the epileptogenic zone (EZ) is crucial. Fast ripples (FRs; 200-600 Hz) are one of the promising biomarkers that can aid in EZ delineation. However, recording FRs requires small surface electrodes. These microelectrodes suffer from high impedance, which significantly impacts FR observability and detection. In this study, we explored the potential of a conductive polymer coating to enhance FR observability. We employed biophysical modeling to compare two types of microelectrodes: Gold (Au) and Au coated with the conductive polymer poly(3,4-ethylenedioxythiophene)-poly(styrene sulfonate) (Au/PEDOT:PSS). These electrodes were then implanted in the CA1 hippocampal neural network of epileptic mice to record FRs during epileptogenesis. Results showed that polymer-coated electrodes demonstrate two-order lower impedance and a higher transfer function amplitude and cut-off frequency. Consequently, FRs recorded with the PEDOT:PSS coated microelectrode yielded significantly higher signal energy compared to the uncoated one. The coating with PEDOT:PSS improved the observability of recorded FRs and therefore their detection. This work paves the way for the development of signal-specific microelectrodes design allowing better targeting of pathological biomarkers.

Breast cancer has become the most diagnosed cancer in women globally with 2.3 million new diagnosis each year. Accurate early staging is essential for improving survival rates with metastatic spread from loco regional to distant metastasis decreasing rates by 50%. Current guidelines do not advice the routine use of Positron Emission Tomography (PET)-Computed Tomography (CT) in staging of early breast cancer in the absence of symptoms. However, there is a growing body of evidence to suggest that PET-CT used in this early stage can benefit the patient by improving staging and as a result treatment and outcome as well as psychological burden without increasing costs to the health service. Ongoing research in PET radiomics and artificial intelligence is showing promising future prospects in its use in diagnosis, staging, prognosticatication and assessing response to treatment in breast cancer. Furthermore ongoing research to address current limitations of PET-CT by improving techniques and tracers is encouraging.

Diffuse optical tomography (DOT) is an optical medical imaging method that can assess the structural properties of tissues and their functional characteristics, such as hemoglobin concentration, water content, as well as lipid concentration, via three-dimensional image reconstruction. This paper presents the theoretical basis and working principle of diffuse optical tomography. The paper explains how the optical properties of tissue can be imaged by photon migration techniques based on diffusion theory. The author presents the reasoning for near-infrared (NIR) imaging as the most effective technique in terms of quantitative recovery of spectroscopic optical parameters. This work also listed various advantages, applications, and challenges of DOT. The paper also briefly discusses current progress in near-infrared medical imaging and its future direction.

The paper presents a method for determining the mutual impedance of two dipoles located on a multilayer dielectric structure. Determining the mutual impedance of linear antennas is a complex issue and we are unable to obtain an exact solution, it is influenced by many elements (location, dimensions, electrical parameters of the earth, thickness of the substrate, thickness and antenna conductivity, etc.) In the case of antennas on a dielectric substrate, the coupling analysis is even more complicated, because the operation of these antennas is significantly influenced by the occurrence of surface waves conducted through an open dielectric structure. The problem was solved by the method of moments using the Galerkin method as its special case. The work uses a method developed by Richmond for obtaining the elements of the impedance matrix, based on the concept of reaction between sections of the base and testing functions. Their mutual interaction was described by the reaction of the electric field caused by the current flowing through one dipole with the current flowing through the other dipole. Based on this analysis, the mutual impedance of two arbitrarily oriented dipoles located on a multilayer dielectric was determined, where the current distribution and antenna lengths are arbitrary. A computer program was developed that allowed to determine the mutual impedance for freely oriented dipoles.

This study aimed to assess the physical characteristics of elite international soccer referees, compare them with other referee populations in the literature, and establish reference tolerance ellipses for the bioelectrical impedance vector analysis (BIVA) point graph. Forty-one elite international soccer referees (age 38.8 ± 3.6 years) participated in the study. the participants underwent body composition assessments, including dual-energy X-ray absorptiometry, BIVA, and somatotype. The Somatotype Attitudinal Distance (SAD), the two-sample Hotelling’s T2 test, and the Mahalanobis test were used to determine somatotype and bioelectrical vector differences with the literature. The average somatotype of the referees was a balanced mesomorph (2.8, 6.5, 2.8). Elite international referees significantly differed from other samples in the literature (SAD = 2.1, 2.6, 2.9 with respect to Zimbabwean, Brazilian, and South African referees, respectively). The bioelectrical vector was significantly different from the general population (T2  76.6; F = 38.8; D = 1.44; P < 0.001) and athletes (T2  25.3; F = 12.6; D = 0.8; P < 0.001). Somatotype values and tolerance ellipses from this study may be useful as a reference for developing training programs and improving the selection process of referees in soccer.

Diffuse optical tomography (DOT) is a medical imaging procedure using light to measure the geometric and working properties of cells, for instance, oxygen consumption, water content, and fat percentage in the tissue by performing three-dimensional visualization of the tissue. This paper aims to explain the theory behind diffuse optical tomography imaging and how the technology works. The paper explains how photon migration techniques based on diffusion theory can be used to image the optical properties of tissue. There are several reasons why near-infrared (NIR) imaging is the most effective method in terms of recovering optical parameters quantitatively in the near-infrared region. The author discusses the methods in detail. This research also presents various advantages, practical uses, and potential problems that have been related to DOT in this work. There is also a brief discussion of current research developments in medical imaging using near-infrared wavelengths, and what the future holds for that area.

Vascular endothelial growth factor (VEGF) is a important biomarker with significant clinical importance. It plays a key role in angiogenesis, would healing, tumor growth, lung development, and in retinal diseases. Hence, detecting and quantifying VEGF is crucial in clinical diagnosis and prognosis of various diseases. In this work, a simple but highly cost-effective platform is developed for VEGF protein detection by using commercially available interdigitated sensors that are modified through surface chemistry tagged with DNA aptamer grafting. The dielectric characteristics between the fingers of sensor is modulated by the negatively charged aptamer-VEGF capture and the impedance is estimated using impedance analyzer. Impedance spectra tests was compared between pristine unmodified, functionalized monolayer surfaces and aptamer-grafted surfaces in order to evaluate the efficacy of VEGF detection. In our results, the sensitivity experiments as conducted had shown the ability of the interdigitated sensor to detect VEGF at a low concentration of 5 pM. The specificity of the functionalized sensor in detecting VEGF is further studied by comparing the impedance to platelet-derived growth factor (PDGF), and the results confirm the specificity of the sensor. Finally, an alternative illustration of impedance spectra is also proposed to improve the data visualization, and such presentation may be potential for intelligent VEGF detection.

Rail impedance directly affects the transmission performance of track circuit . Considering the condition of earth stratification, for the difficult to calculate the rail impedance due to the semi-infinite integration interval and the oscillation of the integrand by using the Carson formula, The truncation method is proposed to divide the impedance formula is divided into definite integral and tail integral. The integral is approximated by the spline function, and the tail integral is calculated by using the exponential integral and Euler formula. Based on it, the rail impedance calculation formula of track circuit is obtained. The electromagnetic field model of track circuit with earth stratification is simulated by finite element method, and the correctness of the method is verified. Based on the formula, the influence of current frequency, soil depth and conductivity on rail impedance is studied. The relative error between the calculated results of rail impedance and the simulation results of finite element is within 5%. It can be seen that the formula has high accuracy and correctly reflects the law of rail impedance variation with current frequency, soil depth and resistivity. It provides a reliable reference for the theoretical calculation of rail impedance of track circuit.

Pathogens and adulterants in human feeding consumables can be readily identified according to their electrical properties. Electrical bioimpedance analysis (BIA) has been widely used for body contents characterization, such as blood, urine, lactate and sweat. If the blood glucose concentration alters the electrical properties of the blood medium, then the impedance spectrum obtained by BIA can be used to measure glycemia. In some applications, artificial neural networks allows the correlation of these parameters (impedance and glucose concentration) by means of symbolic and statistical rules. According to our literature review, there is any physical model that allows the interpretation of the relationship between blood’s electrical properties, obtained by BIA, and the concentration of glucose in the blood plasma. This article proposes a simplified physical model for blood electrical conductivity as a function of glucose concentration, based on Bruggeman’s effective medium theory. The equations of this model were obtained considering an insulating phase distribution diffused in a conductive matrix, in which red blood cells are represented by macroscopic insulating nuclei and glucose molecules by microscopic insulating particles. The impedance spectrum for different glucose concentrations (4.0 to 6.8 mmol/L) in a blood sample, published by Kamat Bagul (2014), were compared with the proposed model. The results showed a significant correlation with the experimental data, showing a maximum error of 5.2%. The proposed model might be useful in the design of noninvasive blood glucose monitoring systems.

Bio-devices are designed to allow biological matter to perform in vitro almost the same functions it performs in vivo. Therefore, they can benefit from the specificities of such materials and are expected to perform better than traditional devices. On the other hand, the integration of biological material with electronic/electrochemical instrumentation requires careful attention and can produce unconventional results. In this paper, we describe the impedance response of an electrochemical cell that converts sunlight into electrical power. It uses the photosynthetic system known as Reaction Center, which is the core of photosynthesis in several living beings. Under illumination, an abrupt transformation drives the cell electrical response from insulator to conductor and a photocurrent is observed. The impedance spectrum shows a peculiar shape which significantly modifies with the protein activation. It has been analyzed by means of a graphical/analytical/ numerical procedure. The modelling identifies an analogue electrical circuit, whose parameters give quantitative information about the underlying process. Finally, an appropriate normalization of data is proposed which validates data in dark and light and can be useful as a fast screening of measurements.

Background: Endogenous Candida endophthalmitis (ECE) is a rare but sight-threatening disease. Patients with ECE present with various clinical signs and symptoms, which can complicate the diagnosis. The aim of this report was to describe the characteristic features of ECE on optical co-herence tomography (OCT) and OCT angiography (OCTA). Another objective was to demon-strate the outcomes of treatment and to diagnose macular complications caused by intraocular inflammation. Case presentation: A 41-year-old woman with a history of acute intermittent por-phyria presented with a progressive vision loss in her left eye. Left-eye OCT revealed findings consistent with a fungal etiology, which was confirmed by the culture of swabs collected from a central vein catheter. The outcomes of intravenous fluconazole treatment were not satisfactory, and the patient developed recurrent attacks of porphyria, suggesting a porphyrogenic effect of systemic antifungal therapy. Repeated intravitreal injections with amphotericin B led to a gradu-al regression of inflammatory lesions. However, follow-up examinations revealed active macular neovascularization on both OCT and OCTA. The patient was administered intravitreal bevaci-zumab. Conclusions: This case highlights the importance of OCT and OCTA as valuable noninva-sive imaging techniques for the identification of ECE, the monitoring of its clinical course, and the diagnosis of macular complications.

Objective: Polymyalgia rheumatica (PMR) and giant cell arteritis (GCA) are often overlapping conditions. We aimed to determine whether 18F-fluorodeoxyglucose (FDG) positron emission tomography-computed tomography (PET-CT) is useful in identifying PMR in the setting of large vessel vasculitis (LVV)-GCA. Methods: Patients diagnosed with LVV-GCA by PET-CT at a tertiary referral hospital for a population of 450,000 people over a two-year period were reviewed. Scoring was performed based on potential significant FDG uptake at up to 16 sites in nine different extravascular areas (SCORE 16). Differences in extravascular sites of significant FDG uptake were evaluated between LVV-GCA with a clinical diagnosis of PMR or not. Results: Fifty-four patients were diagnosed with LVV-GCA by 18F-FDG-PET-CT. Of them, 21 (38.8%) were clinically diagnosed with PMR. Significant extravascular FDG uptake was more frequently observed in those with a clinical diagnosis of PMR. In this sense, the SCORE 16 was higher in those with clinical PMR (5.10 ± 4.05 versus 1.73 ± 2.31 in those without a clinical diagnosis of PMR; p< 0.001). A SCORE 16 involving more than 4 sites of significant FDG uptake yielded a sensitivity of 52% and a specificity of 91% for establishing a clinical diagnosis of PMR associated with LVV-GCA. The best areas of significant FDG uptake to clinically identify PMR in patients with LVV were the shoulder, the greater trochanter and the lumbar interspinous regions with an area under the ROC curve of 0.810 (0.691-0.930). Conclusion: Significant extravascular 18F-FDG-PET-CT uptake may help establish a clinical diagnosis of PMR in patients with LVV-GCA. These patients are more commonly diagnosed with PMR if they have significant FDG uptake in the shoulder, greater trochanter, and lumbar interspinous areas.

This paper reviews several techniques, including analytical theories and real frequency techniques, to design ultra-wideband impedance matching networks for low-power applications. The comparison of solutions obtained using the simplified real frequency technique to the published solution using Chebyshev filter theory is demonstrated.

. The impedance change of an induction coil surrounding a metal tube adapter is investigated by the truncated region eigenfunction expansion (TREE) method. Conventional TREE method is inapplicable to this problem as a consequence of the numerical overflow of eigenfunctions of the air-metal multi-subdomain regions. The difficulty is surmounted by a normalization procedure for the numerical eigenfunctions obtained from the finite element method (FEM). Efficient algorithm is devised by the Clenshaw-Curtis quadrature rule for integrals involving the numerical eigenfunctions. Numerical results of the TREE and FEM simulation coincide very well in all cases, and the efficiency of the proposed method is also confirmed.

A great improvement in food safety and quality controls worldwide has been achieved through the development of biosensing platforms. Foodborne pathogens continue to cause serious outbreaks due to the ingestion of contaminated food. The development of new, sensitive, portable, high-throughput, and automated platforms is a primary objective to allow detection of pathogens and their toxins in foods. Listeria monocytogenes is one common foodborne pathogen. Major outbreaks of listeriosis have been caused by a variety of foods, including milk, soft cheeses, meat, fermented sausages, poultry, seafood and vegetable products. Due to its high sensitivity and easy setup, electrochemical impedance spectroscopy (EIS) has been extensively applied for biosensor fabrication and in particular in the field of microbiology as a mean to detect and quantify foodborne bacteria. Here we describe a miniaturized, portable EIS platform consisting of a microfluidic device with EIS sensors for the detection of L. monocytogenes in milk samples, connected to a portable impedance analyzer for on-field application in clinical and food diagnostics but also for biosecurity purposes. To achieve this goal microelectrodes were functionalized with antibodies specific for L. monocytogenes. The binding and detection of L. monocytogenes was achieved in the range 2.2 x 103 cfu/ml to 1 x 102 with a Limit of Detection (LoD) of 5.5 cfu/ml.

18F-fluorodeoxyglucose positron emission tomography and computed tomography (18F-FDG PET-CT) is increasingly used in the diagnosis, prognosis, staging, and treatment monitoring of many tumor types. However, only a small number of studies have reported the use of 18F-FDG PET-CT in intrahepatic cholangiocarcinoma (ICC). This study aimed to examine the accuracy of tumor staging in ICC by using 18F-FDG PET-CT. Between January 2009 and December 2020, patients with suspected ICC were retrospectively enrolled in the study and underwent imaging. The sensitivity and specificity of 18F-FDG PET-CT, CT, and magnetic resonance imaging (MRI) in detecting tumors, satellite focus, vascular invasion, and lymph node metastases were analyzed. The efficacy of 18F-FDG PET-CT for tumor staging was evaluated. Of the 110 patients who were enrolled in the study, 52 underwent surgical treatment and 45 were histologically diagnosed with ICC. When compared with CT or MRI, 18F-FDG PET-CT had similar sensitivity and specificity values for diagnosing satellite focus and vascular and bile duct invasion; however, PET-CT showed higher accuracy in diagnosing regional lymph node metastases. The accuracy of tumor staging by 18F-FDG PET-CT was higher than that by CT/MRI. Thus, 18FDG PET-CT may support tumor staging in ICC.

Engineering of quantum computers requires reliable characterization of qubits, quantum operations, and even the entire hardware. Quantum tomography is an indispensable framework in quantum characterization, verification, and validation (QCVV), which has been widely accepted by researchers. According to the tomographic target, quantum tomography can be categorized into quantum state tomography (QST), quantum process tomography (QPT), gate set tomography (GST), process tensor tomography (PTT), and instrument set tomography (IST). Standard quantum tomography toolkits generally consist of basic linear inverse methods and statistical maximum likelihood estimation (MLE) based methods. Furthermore, the performance of standard methods, including effectiveness and efficiency, has been further developed by exploiting Bayesian estimation, neural networks, matrix completion techniques, etc. In this review, we introduce the fundamental quantum tomography techniques, including QST, QPT, GST, PTT, and IST. We first introduce the details of basic linear inverse methods. Then, the framework of MLE methods with constraints is summarized. Finally, we briefly introduce recent further research in developing the performance of tomography. This review provides a primary getting-start in developing quantum tomography, which promotes quantum computer development.

Background: Pulmonary sequestration (PS), generally diagnosed using computed tomography pulmonary angiography (CTPA), is a rare congenital developmental malformation of the lung that is characterized by nonfunctional lung tissue independent of the normal lung tissue. This study summarizes the imaging features of the supplying arteries and draining vessels in patients with PS with an aim to assist with timely clinical diagnosis and operation guidance. Materials and Methods: A total of 55 patients with PS diagnosed on CTPA from multiple clinical centers were retrospectively analyzed. Data included demographic characteristics, imaging features, disease location, isolation type, and the features of supplying and draining vessels, as shown on CTPA images. Results: Of the 55 patients reviewed, 3 (5.45%) were children, 3 (5.45%) were adolescents, and 49 (89.09%) were adults, with a mean age of 44 years. Fifty-four (98.18%) patients had intralobar sequestration and one (1.82%) had extralobar sequestration. PS was noted 3.5 times more frequently in the left lower lobe than in the right lower lobe. For the supplying arteries, 47 (85.45%) were derived from the descending thoracic aorta, 1 (1.82%) from the abdominal aorta, 7 (12.73%) from the celiac axis, and 1 (1.82%) from the bronchial artery. The draining vessels were the pulmonary veins in 49 patients (89.09%), the umbilical vein in 1 (1.82%), the venae intercostal in 1 (1.82%), the pulmonary arteries in 11 (20.00%), and not shown on the images in 2 (3.64%). Conclusion: Clinical presentations of PS are non-specific and can be easily missed or misdiagnosed. However, CTPA can help improve the diagnostic accuracy and identify the supplying arteries and draining vessels, which significantly contribute to surgical planning.

The signature of chaotic systems can be characterized either by the sensitivity of the initial conditions or by the change of its parameters. This feature can be used for manufacturing high sensitivity sensors. Sensors based on chaotic circuits have already been used for measuring water salinity, inductive effects, and both noise and weak signals. This article investigates an impedance sensor based on the Van der Pol and Duffing damped oscillators. The calibration process is a key point and therefore the folding behavior of signal periods was also explored. A sensitivity of 0.15 kΩ/Period was estimated over a range from 89.5 to 91.6 kΩ. This range can be adjusted according to the application by varying the gain of the operational amplifier used in this implementation. The development of this type of sensor might be used in medical and biological engineering for skin impedance measurements, for example. This type of chaotic sensor has the advantage of sensing small disturbances and then detect small impedance changes within biological materials which, in turn, may not be possible with other detectors.

Accurate evaluation of health status of lithium-ion batteries must be deemed as of great significance, insofar as utility and safety of batteries are of concern. Lithium plating, in particular, is notoriously known to be a chemical reaction that can cause deterioration in, or even fatal hazards to, the health of lithium-ion batteries. Electrochemical impedance spectroscopy (EIS), which has distinct advantages such as fast or non-destructive over its competitors, suffices in detecting lithium plating and thus has been attracting increasing attention in the field of battery management, but its ability of assessing quantitatively the degree of lithium plating remains largely unexplored hitherto. On this point, this work seeks to narrow that gap, by proposing an EIS-based method that can quantify the degree of lithium plating. The core conception is to eventually circumvent the reliance on state-of-health measurement, and use instead the impedance spectrum, to acquire an estimate on battery capacity loss. To do so, the effects of solid electrolyte interphase formation and lithium plating on battery capacity must be first decoupled, so that the mass of lithium plating can be quantified. Then, based on an impedance spectrum measurement, the parameters of the fractional equivalent circuit model (ECM) of the battery can be identified. These fractional ECM parameters are received as inputs by an artificial neural network, which is tasked to establish a correspondence between the model parameters and the mass of lithium plating. The empirical part of the work revolves around the data collected from an aging experiment, and the validity of the proposed method is truthfully attested by dismantling the batteries, which is otherwise not needed during the actual uptake of the method.

A novel configuration for a super-wide impedance planar antenna is presented based on a 2 × 2 microstrip patch antenna (MPA). The antenna comprises a symmetrical arrangement of four-square patches that are interconnected to each other with cross-shaped high impedance microstrip lines. The antenna array is exciting through a single feedline connected to one of the patches. The proposed antenna array configuration overcomes the main drawback of conventional MPA of narrow bandwidth that is typically <5%. The antenna exhibits a super-wide frequency bandwidth from 20 GHz to 120 GHz for S₁₁<−15 dB, which corresponds to a fractional bandwidth of 142.85%. The antenna’s performance of bandwidth, impedance match, and radiation gain were enhanced by etching slots on the patches. The slotted microstrip patch essentially acts like a left-handed capacitance to exhibit metamaterial properties over a given frequency range. With the inclusion of the slot the maximum radiation gain and efficiency of the MPA have increased to 15.11 dBi and 85.79% at 80 GHz, which show an improvement of 2.58 dBi and 12.54%, respectively. The dimension of each patch antenna is 30 × 30 mm². The results show that the proposed MPA is useful for various communications existing and emerging systems such as ultra-wideband (UWB) communications, RFID systems, massive multiple-output multiple-input (MIMO) for 5G, and radar systems.

The new hybrid composite materials for PEM fuel cell were synthesized by UV-polymerization of acrylic monomers (acrylonitrile (AN), acrylic acid (AA), ethylene glycol dimethacrylate (EGDMA)) and sulfo aromatic monomer – sodium styrene sulfonate (SSS), and tetraethoxysilane/3-methacryloxypropyltrimethoxysilane (TEOS/MAPTMS)-based sol-gel system. By means of X-ray spectroscopy fractal structure of the obtained materials was characterized. Proton conductivity and viscoelastic properties of the materials were investigated depending on the content of inorganic component in nanocomposites. On the basis of impedance studies, an equivalent scheme is proposed that successfully describes the proton conductivity in the synthesized composite electrolyte membranes.

The unreliable prediction of the low frequency components from inverted acoustic impedance causes uncertainty in quantitative seismic interpretation. To address this issue, we first calculate various seismic and geological attributes that contain low frequency information, such as relative geological age, interval velocity, and integrated instantaneous amplitude. Then, we develop a method to predict the low frequency content of seismic data using these attributes, their high frequency components, and recurrent neural networks. Next, we test how to predict the low frequency components using stacking velocity obtained from velocity analysis. Using all the attributes and seismic data, we propose a supervised deep learning method to predict the low frequency components of the inverted acoustic impedance. The results obtained in both synthetic and real data cases show that the proposed method can improve the prediction accuracy of the low frequency components of the inverted acoustic impedance, with the best improvement in a real data example of 57.7% compared with the impedance predicted using well log interpolation.

Acoustic energy dissipates in multi-phase or multi-boundary materials. Hybrid composites are described as multi-phase with many interfaces between their materials. The current research proposes studying the acoustic behavior of polymeric hybrid composites by estimating the time, velocity, and hybrid composite acoustic impedance. Two groups of hybrid composites were prepared, including unsaturated polyester with PMMA, except one with HDPE and the other with PS. Each group has 28, 35, and 40% weight fractions. An ultrasonic test measured time to determine velocity and acoustic impedance later. The results show that increasing the weight fraction will increase density with respect to the density of the reinforcing material. Different ultrasonic times were obtained with increasing weight fractions. As the weight fraction of PS increased, the time increased; unlike the velocity, it decreased but increased with density. In contrast, this behavior was changed if the hybrid had PE. The highest acoustic impedance was at 28% UP/PMMA+PS. In conclusion, UP/PMMA+PS can dissipate ultrasonic waves more than UP/PMMA+PE.

A portable, electrical impedance spectroscopy device to monitor the bioimpedance’s resistive component of beef meat by injecting a sinusoidal current of 1mA at 65.5 kHz was developed. In 4 slaughtered beef both right and left longissimus dorsi muscles where trimmed and left muscle portion was frozen to -18° C up to 7^th day while right one was meantime maintained at 5° C. Median value of specific resistivity of not-frozen sample was about twice Ω cm^-1 with respect of that of frozen-thawed sample (P = 0.004). It was concluded that the device is reliable to monitoring the ripening of beef meat in situ.

Accurate image registration is essential for eye movement compensation in optical coherence tomography (OCT) and OCT angiography (OCTA). The spatial resolution of an OCT instrument is typically anisotropic, i.e., different resolutions in the lateral and axial dimensions. When OCT images have anisotropic pixel resolution, residual distortion (RD) and false translation (FT) were always observed after image registration for rotational movement. In this study, RD and FT were quantitively analyzed over different degrees of rotational movement and various lateral and axial pixel resolution ratio (RL/RA) values. The theoretical analysis confirmed that the RD and FT increase significantly with the rotation degree and RL/RA. An image resizing assisting registration (RAR) strategy was proposed for accurate image registration. The performance of direct registration (DR) and RAR for retinal OCT and OCTA images were quantitatively compared. Experimental results confirmed that unnormalized RL/RA causes RD and FT, RAR can effectively improve the performance of OCT and OCTA image registration and distortion compensation.

ABSTRACT Objectives: Typical Diagnostic Reference Levels (DRL) in terms of Computed Tomography Dose Index (CTDI) and patient dose in terms of Effective Dose (ED ) and Size Specific Dose Estimate (SSDE) were estimated in Computed Tomography (CT) guided biopsy procedures. Materials and Methods: A total of 226 CT biopsy procedures - Iliac bone, liver, lung, mediastinum and para-aortic tissue - were retrospectively analyzed and Typical DRL extracted based on ICRP 135 instructions. Results: For helical mode acquisitions, DRLs in terms of CTDIvol were 9.7 mGy for Iliac bone, 8.9 mGy for liver, 8.8 mGy for lung, 7.9 mGy for mediastinal mass and 9 mGy for para-aortic lymph nodes biopsy procedures. For biopsy acquisitions, DRL values were 7.3 mGy, 7.7 mGy, 5.6 mGy, 5.6 mGy and 7.4 mGy respectively. Also, SSDE median values ranged from 7.6 mGy to 10 mGy for biopsy acquisitions and 11,3 mGy to 12,6 mGy for helical acquisitions, as well as the median values for effective dose ranged from 1.6 mSv to 5,7 mSv for biopsy scans and 3.9 to 9.3 mSv for helical scans. Conclusions: The use of DLR as an optimization tool for CT-guided biopsy procedures revealed that helical scans across the entire anatomical region greatly affect radiation dose compared to biopsy acquisitions.

(1) Background: To estimate resistance, reactance and phase angle values among moderate preterm infants and their variation according to neonatal and maternal characteristics and nutritional intake. (2) Methods: This was a cohort that evaluated 43 moderate preterm infants using bioelectrical impedance analysis. The study variables included resistance, reactance and PA measurements, in addition to classification of nutritional intake. (3) Results: The mean resistance was 602.0+118.2 Ω, reactance was 57.2 Ω (IIQ = 42.6-65.2) and phase angle was 522° (IIQ = 4.1-6.6). Lower resistance values were found in the presence of risky pregnancy (532.2+111.9 Ω vs 650.9+97.9 Ω, p&lt;0.001) and lower reactance values, in the presence of harmful maternal lifestyle habits at both the first (p=0.01) and second assessments (p=0.01). Eight preterm infants were considered to have insufficient nutritional intake (23.5%); 17, sufficient (50.0%) and 9, partially sufficient (26.5%). There was less reactance among preterm infants with insufficient nutritional intake (p &lt; 0.001). (4) Conclusions: The bioelectrical impedance analysis measurements were within the range of values reported in other studies. There was an association between full diet and adequate nutritional intake with higher resistance values, and a lower reactance value was associated with the presence of risky pregnancy and harmful maternal lifestyle.

Background and purpose: Dynamic 18F-FDG PET-CT scanning can accurately quantify 18F-FDG uptake and has been successfully applied in diagnosing and evaluating therapeutic effects in various malignant tumors. There is no conclusion as to whether it can accurately distinguish benign and malignant lymph nodes in nasopharyngeal cancer. The main purpose of this study is to reveal the diagnostic value of dynamic PET-CT in cervical lymph node metastasis of nasopharyngeal cancer through analysis. Method: We first searched for cervical lymph nodes interested in static PET-CT, measured their SUV-Max values, and found the corresponding lymph nodes in magnetic resonance images before and after treatment. The valid or invalid groups were included according to the changes in lymph node size before and after treatment. Their Ki values were measured on dynamic PET-CT and compared under different conditions. Then, we conducted a correlation analysis between different factors and Ki values. Finally, diagnostic tests were conducted to compare the sensitivity and specificity of Ki and SUV-Max. Result: We included 67 cervical lymph nodes from different regions of 51 nasopharyngeal cancer patients and divided them into valid and invalid groups based on changes before treatment. The valid group includes 50 lymph nodes, while the invalid group includes 17. Significant differences (P<0.001) between the two groups in SUV-Max, Ki-Mean, and Ki-Max values. When the SUV-Max≤4.5, there was no significant difference in the Ki-Mean and Ki-Max between the two groups (P>0.05). When SUV-Max≤4.5 and pre-treatment lymph nodes<1.0cm, the valid group had significantly higher Ki-Mean (0.00910) and Ki-Maximum (0.01004) values than the invalid group (Ki-Mean=0.00716, Ki -Max=0.00767) (P<0.05). When SUV-Max≤4.5, pre-treatment lymph nodes<1.0cm, and EBV DNA replication was normal, Ki-Mean (0.01060) and Ki-Max (0.01149) in the valid group were still significantly higher than the invalid group (Ki-Mean=0.00670, Ki-Max=0.00719) (P<0.05). The correlation analysis between different factors (SUV-Max, T-stage, normal EB virus DNA replication, age, pre-treatment lymph node<1.0cm) and Ki value showed that SUV-Max and pre-treatment lymph node<1.0cm were related to Ki-Mean and Ki-Max. Diagnostic testing was conducted, the AUC value of the SUV-Max value was 0.8259 (95% confidence interval: 0.7296-0.9222), the AUC value of the Ki-Mean was 0.8759 (95% confidence interval: 0.7950-0.9567), and the AUC value of the Ki-Max was 0.8859 (95% confidence interval: 0.8089-0.9629). It was found that the sensitivity of SUV-Max was 88%, the specificity was 76%, the sensitivity of Ki-Mean was 88%, the specificity was 80%, the sensitivity of Ki-Max was 94%, the specificity was 76%, the specificity of Ki-Mean was better than SUV-Max, the sensitivity of Ki-Max was better than SUV-Max. Conclusion: Dynamic PET-CT has shown significant diagnostic value in diagnosing cervical lymph node metastasis of nasopharyngeal cancer, especially for the small SUV value, and lymph nodes do not meet the metastasis criteria before treatment, and EBV DNA replication is normal. Moreover, its sensitivity and accuracy are superior to static PET-CT.

Electrochemical Impedance Spectroscopy (EIS) is a powerful non-invasive technique used to characterize Lithium-ion cells. Its application allows to identify and track the evolutions of cell degradation processes within a short testing time. This review collects all the available works which have used EIS spectra either to characterize Li-ion cell degradation or to develop Electric Circuit Models (ECMs). The objectives of this work are: (i) to highlight the influence of different aging test conditions on the EIS spectra; (ii) to find the correlations between EIS spectra variations and the underlying degradation mechanisms and (iii) to list the available options to formulate ECMs from EIS spectra of aged cells. After an exhaustive analysis of the state-of-the-art, a critical review is presented to discuss the existing links between degradation mechanisms and the most reliable solutions to model them.

Body composition measurement plays an important auxiliary role in the nutritional assessment of diseases, nutritional diagnosis and the evaluation of the effect of nutritional therapy. There are many techniques and methods available for the measurement of body composition. Bioelectrical impedance analysis (BIA ) of body composition has been widely used and explored in many diseases in the past 30 years. Its main advantages are its non-invasiveness, non-radiation, economy, convenience and feasibility. With the development of bioelectrical impedance technology, bioelectrical impedance analysis has gradually developed from single-frequency BIA (SF-BIA) to dual-frequency BIA (DF-BIA). now devices are available that measure at multiple fixed frequencies (multi-frequency BIA, MF-BIA) and over a range of frequencies (bioimpedance spectroscopy, BIS). The clinical significance of nutrition management in chronic kidney disease has gradually become prominent. Bioelectrical impedance analysis of body composition is favored by nephrologists and nutritionists as an auxiliary method for nutrition diagnosis, treatment and monitoring. In the past 20 years, there have been many studies on body composition measurement by bioelectrical impedance analysis in the nutritional management of CKD patients. This article will summarize the recent research results of BIA of body composition method in the nutrition management of CKD patients in pre-dialysis, hemodialysis, peritoneal dialysis and kidney transplantation, in order to provide reference for the application and research of BIA method in the nutrition management of chronic kidney disease in the future.

This paper presents a method to detect and classify the high impedance fault that occur in the medium voltage distribution network using discrete wavelet transform (DWT) and adaptive neuro-fuzzy inference system (ANFIS). The network is designed using Matlab software and various faults such as high impedance, symmetrical and unsymmetrical fault have been applied to study the effectiveness of the proposed ANFIS classifier method. This is achieved by training the ANFIS classifier using the features (standard deviation values) extracted from the three phase fault current signal by DWT technique for various cases of fault with different values of fault resistance in the system. The success and discrimination rate obtained for identifying and classifying the high impedance fault from the proffered method is 100% whereas the values are 66.7% and 85% respectively for conventional fuzzy based approach. The results indicate that the proposed method is more efficient to identify and discriminate the high impedance fault accurately from other power system faults in the system.

Optical coherence tomography (OCT) can help in the diagnosis and treatment of infectious keratitis, but it has not been studied in cases occurring after corneal refractive surgery procedures such as femtosecond laser in situ keratomileusis (FS-LASIK) and keratorefractive lenticule extraction (KLEx). In these procedures a surgical interface is created, where infections usually start, thus determining a different OCT pattern compared to non-surgical infections, which instead begin in the corneal surface. A total of 4 cases of post-refractive surgery infectious keratitis are reported (2 after FS-LASIK and 2 after KLEx), in which the OCT identified an initial infiltrate in the interface, followed by interface inflammation. In 1 case after FS-LASIK, interface fluid accumulation occurred. In 1 case after KLEx, diffuse interface inflammation led to stromal reabsorption, later compensated by stromal reformation and epithelial hyperplasia, well documented by OCT.

(1) Background: To determine the diagnostic accuracy that optical coherence tomography (OCT) can add to fundus photography (FP) in assessing the condition of the retinal posterior pole; (2) Methods: Two blocks of analysis: at first, the posterior pole of each eye was examined using FP non-mydriatic imaging device. Secondly: OCT was used in addition to FP. After consolidating specific diagnostic criteria, the assessments were evaluated by two blinded independent investigation groups (by optometrists, and by ophthalmologists who was considered the gold standard); (3) Results: We calculated the diagnostic accuracy of FP compared to OCT and found that both had similar sensitivity, FP had slightly higher specificity, (p-value: 0.01) and OCT had a higher kappa coefficient 0.50 (95%CI: 0.46-0.55) vs 0.39 (95%CI: 0.34-0.45) of FP; (4) Conclusions: Based on the premise that the role of the optometrist in Spain is not to diagnose but to detect lesions and refer patients to an ophthalmologist, the results of this study support the use of OCT, that it provided gradable images in almost all examined eyes (97.5%), compared to FP (73.5%). However, the optometrist need a detailed and standardized guide in order to evaluate according to the ophthalmologist's criteria.

Practical entanglement distillation is a critical component in quantum information theory. Entanglement distillation is often utilized for designing quantum computer networks and quantum repeaters. The practical entanglement distillation problem is formulated as a bilevel optimization problem. A fuzzy formulation is introduced to estimate the quantum state (density matrix) from pseudo-likelihood functions (i.e., quantum state tomography). A scale-independent relationship between fuzzy relations in terms of the pseudo-likelihood functions is obtained. The entanglement distillation optimization problem was solved using the combined coupled map lattice and dual annealing approach. Comparative analysis of the results is then conducted against a standard dual annealing algorithmic implementation.

Animal models of Alzheimer’s disease amyloidosis that recapitulate cerebral amyloid-beta pathology have been widely used in preclinical research, and have greatly enabled the mechanistic understanding of Alzheimer’s disease and the development of therapeutics. Comprehensive deep phenotyping of the pathophysiological and biochemical features in these animal models are essential. Recent advances in positron emission tomography have allowed the non-invasive visualization of the alterations in the brain of animal models as well as in patients with Alzheimer’s disease, These tools have facilitated our understanding of disease mechanisms, and provided longitudinal monitoring of treatment effect in animal models of Alzheimer’s disease amyloidosis. In this review, we focus on recent positron emission tomography studies of cerebral amyloid-beta accumulation, hypoglucose metabolism, synaptic and neurotransmitter receptor deficits (cholinergic and glutamatergic system), blood-brain barrier impairment and neuroinflammation (microgliosis and astrocytosis) in animal models of Alzheimer’s disease amyloidosis. We further propose the emerging targets and tracers for reflecting the pathophysiological changes, and discuss outstanding challenges in disease animal models and future outlook in on-chip characterization of imaging biomarkers towards clinical translation.

We present progress in fast, high-resolution imaging, material classification, and fault detection using hyperspectral X-ray measurements. Classical X-ray CT approaches rely on data from many projection angles, resulting in long acquisition and reconstruction times. Additionally, conventional CT cannot distinguish between materials with similar densities. However, in additive manufacturing, the majority of materials used are known a priori. This knowledge allows to vastly reduce the data collected and increase the accuracy of fault detection. In this context, we propose an imaging method for non-destructive testing of materials based on the combination of spectral X-ray CT and discrete tomography. We explore the use of spectral X-ray attenuation models and measurements to recover the characteristic functions of materials in heterogeneous media with piece-wise uniform composition. We show by means of numerical simulation that using spectral measurements from a small number of angles, our approach can alleviate the typical deterioration of spatial resolution and the appearance of streaking artifacts.

The technique of Faraday tomography is a key tool for the study of magnetised plasmas in the new era of broadband radio polarisation observations. In particular, observations at metre-wavelengths provide significantly better Faraday depth accuracies compared to traditional cm-wavelength observations. However, the effect of Faraday depolarisation makes the polarised signal very challenging to detect at metre wavelengths (MHz frequencies). In this work, Faraday tomography is used to characterise the Faraday rotation properties of polarised sources found in data from the LOFAR Two-Metre Sky Survey (LoTSS). Of the 76 extragalactic polarised sources analysed here, we find that all host a radio-loud AGN. The majority of the sources (∼64%) are large FRII radio galaxies with a median projected linear size of 710 kpc and median radio luminosity at 144 MHz of 4 × 10^26 W/Hz. In several cases, both hotspots are detected in polarisation at an angular resolution of ∼20". One such case allowed a study of intergalactic magnetic fields on scales of 3.4 Mpc. Other detected source types include an FRI radio galaxy and at least 8 blazars. Most sources display simple Faraday spectra, however, we highlight one blazar that displays a complex Faraday spectrum, with two close peaks in the Faraday dispersion function.

Subglottal Impedance-Based Inverse Filtering (IBIF) allows for the continuous, non-invasive estimation of glottal airflow from a surface accelerometer placed over the anterior neck skin below the larynx, which has been shown to be advantageous for the ambulatory monitoring of vocal function. However, during long-term ambulatory recordings over several days, conditions may drift from the laboratory environment where the IBIF parameters were initially estimated due to sensor positioning, skin attachment, and temperature, among other factors. Observation uncertainties and model mismatch may result in significant deviations in the glottal airflow estimates, but are very difficult to quantify in ambulatory conditions due to a lack of a reference signal. To address this issue, we propose a Kalman filter implementation of the IBIF filter, which allows for both estimating the model uncertainty and adapting the airflow estimates to correct for signal deviations. One-way ANOVA results from laboratory experiments using the Rainbow Passage indicate a an improvement on amplitude-based measures for PVH subjects compared to IBIF which shows a statistically difference with respect to the reference oral airflow (p=0.02,F=4.1). MFDR from PVH subjects is slightly different to the oral airflow when compared to IBIF (p=0.04, F=3.3). Other measures did not have significant differences with either Kalman or IBIF, with the exception of H1H2, whose performance deteriorates for both methods. Overall, both methods show similar flottal airflow measures, with the advantage of Kalman by improving amplitude estimation. Moreover, Kalman filter deviations from the IBIF output airflow might suggest a better representation of some fine details in the ground-truth glottal airflow signal. Other applications may take more advantage from the adaptation offered by the Kalman filter implementation.

The black hole (BH) phenomenon is an intraluminal restenotic lesion. It was identified by intravascular ultrasound (IVUS) and optical coherence tomography (OCT) after intracoronary brachytherapy and drug-eluting stent implantation. Despite the similarity in the mode of action of brachytherapy and drug-eluting stent implantation, the BH phenomenon appears to be uncommon after drug-eluting stent implantation. Specifically, the BH phenomenon is better identified by OCT than by IVUS. Herein, we present a case of in-stent restenosis with suspected BH phenomenon on IVUS confirmed by OCT.

Abstract Purpose: To analyze the correspondence between refractive astigmatism and corneal astigmatism in pseudophakic eyes with non-toric intraocular lenses. Setting: Yeouido St. Mary hospital, Seoul, South Korea Design: Evaluation of a diagnostic test instrument. Methods: This retrospective study included 95 eyes of 95 patients. Corneal astigmatism was measured with an automated keratometer (RK-5, Canon) and Scheimpflug tomography (Pentacam HR, Oculus). Refractive astigmatism was compared to keratometric astigmatism (based on anterior corneal measurements only), Equivalent K Reading and total corneal astigmatism (both based on anterior and posterior corneal measurements). Vector analysis was carried out by Næser’s polar value method. The accuracy was defined as the average magnitude of the vectorial difference in astigmatism (DA). Each corneal measurement was optimized in retrospect by a multiple linear regression equation between refractive and corneal astigmatism. Results: Keratometric astigmatism overestimated with-the-rule (WTR) refractive astigmatism and underestimated against-the-rule (ATR) refractive astigmatism. Several measurements based on both corneal surfaces values did not show any statistically significant difference with respect to refractive astigmatism. The mean corneal astigmatism by total corneal refractive power (TCRP) at 4.0 mm (zone/pupil) produced the lowest mean arithmetic DA and the highest percentage of eyes with a DA ≤0.50 diopter. After optimization, the accuracies of automated KA and TCRP 4.0 mm (zone/pupil) were similar. Conclusions: Total corneal astigmatism measured by the Scheimpflug tomography at 4.0 mm zone centered on pupil, accurately reflects the refractive astigmatism in pseudophakic eyes. However, the accuracy of total corneal astigmatism is not different from automated KA after optimization.

Aim of the presented research was to develop an optical sensing system to investigate the demineralization process of the bones. Optical measurement techniques are widely used and increasingly adapted in biological and biomedical applications due to their non-destructive nature and safety. Optical examination of the bone condition could facilitate clinical trials and improve the safety of patients. The authors used a set of complementary methods: polarization-sensitive optical coherence tomography (PS-OCT) and Raman spectroscopy. To stimulate the process of demineralization and gradual removal of the hydroxyapatite, the test samples of chicken bones were placed into 10% acetic acid. Measurements were carried out in two series. The first one took two weeks with data acquired every day. In the second series, the measurements were made during one day at an hourly interval (after 1, 2, 3, 5, 7, 10, and 24 hours). Raman spectroscopy was used to evaluate the disappearance of the hydroxyapatite. The relation between the content of hydroxyapatite and images recorded using OCT was analyzed and discussed. Moreover, the polarization properties of the bones have been evaluated. Based on OCT images, the retardation angles of the bones have been calculated. This work presents a preliminary study on the mechanism of bone demineralization and confirms the potential of the applied optical methods.

It is important for researchers in material domain to reconstruct and visualize the microstructure of alloy, which helps discover morphologies and properties that can only be found in three dimensional and microscopic space. However, because of the limitation of state-of-the-art sensors, the internal microstructure of the material is not easy to obtain. In this paper, a novel automatic 3D reconstruction method is proposed using diffraction contrast tomography technology to capture the 3D microstructure of Al-La alloy. The pipeline of the proposed method starts from the imaging of Al-La alloy with the LabDCT technique from Carl Zeiss AG, which produces a sequence of 2D microstructure sections. Then, a segmentation algorithm based on superpixel and lifted multicut is proposed to extract the 2D microstructure in an image section. Finally, 2D segmentations are joined together to reconstruct and visulize the 3D microstructure. As a result, a novel morphology of Al-La alloy is recovered with both dendrite and lamellar morphologies. The proposed method has the advantage of the ability to losslessly recover the internal microstructure.

We discuss the influence played by different statistical models in the prediction of porosity and litho-fluid facies from logged and post-stack inverted acoustic impedance (Ip) values. We compare the inversion and classification results obtained under three different a-priori statistical assumptions: an analytical Gaussian distribution, an analytical Gaussian-mixture model and a non-parametric mixture distribution. The first model assumes Gaussian distributed porosity and Ip values, thus neglecting their facies-dependent behaviour caused by different lithologic and saturation conditions. Differently, the other two statistical models relate each component of the mixture to a specific litho-fluid facies, so that the facies-dependency of porosity and Ip values is taken into account. Blind well tests are used to validate the final predictions, whereas the analysis of the maximum-a-posteriori (MAP) solutions, the coverage ratio and the contingency analysis tools are used to quantitatively compare the inversion outcomes. This work points out that the correct choice of the statistical petrophysical model could be crucial in reservoir characterization studies. Indeed, for the investigated zone it turns out that the simple Gaussian model constitutes an oversimplified assumption, while the two mixture models provide more accurate results, although the non-parametric one yields slightly superior predictions with respect to the Gaussian-mixture assumption.

In the current research work, electrical resistance tomography (ERT) was employed for crystallization process monitoring and visualization. A first-of-its-kind MATLAB-based interactive GUI application “ERT-Vis” is presented. Two case studies involving varied crystallization methods were undertaken. The experiments involving calcium carbonate reactive (precipitative) crystallization for the high conductivity solution-solute media and the cooling crystallization for sucrose crystallization representing the lower conductivity solution-solute combination were designed and performed. The software successfully provided key insights regarding the process progress in both crystallization systems. It could detect and separate the crystal agglomerations in the low as well as high conductivity solutions using visual analytics tools provided. The performance and utility of the software were studied using a software evaluation case study involving domain experts. Participant feedback indicated that ERT-Vis software helps in reconstructing images instantaneously, interactively visualizing, and evaluating the output of the crystallization process monitoring data.

Oncology has emerged as a crucial field of study and treatment in the domain of medicine. Computed tomography has gained widespread adoption as a radiological modality for the identification and characterisation of pathologies, particularly in oncology, enabling precise identification of affected organs and tissues. However, achieving accurate liver segmentation in computed tomography scans remains a challenge due to the presence of artefacts and the varying densities of soft tissues and adjacent organs. This paper compares artificial intelligence algorithms and traditional medical image processing techniques to assist radiologists in liver segmentation on computed tomography scans, and evaluates their accuracy and efficiency. It is noteworthy that although studies have been conducted on liver segmentation in computed tomography scans, they often lack an intuitive and visual component that allows healthcare professionals to manipulate and observe the results obtained, thereby limiting interaction with the outcomes. From the literature review, challenges such as under-segmentation, over-segmentation, and poor boundary detection, as well as the selection of methods to improve the accuracy and efficiency of liver segmentation in computed tomography scanners, are highlighted as needs to be addressed. The importance of future research in understanding the essential features for the study, generating more datasets, improving segmentation efficiency, and developing lightweight artificial intelligence frameworks for liver segmentation is outlined.

This study aimed to estimate scattered radiation and its spatial distribution around three Cone Beam Computed Tomography (CBCT) devices, in order to determine relatively safe positions for an operator to stand if needed to be inside the CBCT room. The following devices were tested: Morita Accuitomo (CBCT1), Newtom Giano HR (CBCT2), Newtom VGi (CBCT3). Scattered radiation measurements were performed using different kVp, mA and Field of View (FOV) options. An anthropomorphic phantom (NATHANIA) was placed inside the x-ray gantry to simulate clinical conditions. Scattered measurements were taken with the ionization chamber Inovision model 451P Victoreen once placed at fixed distances from each irradiation isocenter, away from the primary beam. A statistically significant (p<0.001) difference was found in the mean value of the scattered radiation estimations between the CBCT devices. Scattered radiation was reduced with a different rate for each CBCT device as distance was increased. For CBCT1 the reduction was 0.047μGy, for the CBCT2 0.036 μGy and 0.079 μGy for CBCT3, for every one meter away from the x-ray gantry. Therefore, at certain distances from the central x-ray, the scattered radiation was below the critical 1mGy. Consequently, an operator could stay inside the room accompanying the patient being scanned, if necessary.

OCTA is an imaging modality used in the assessment of the retinal vasculature. It operates on the principle of coherence tomography used in standard OCT with the addition of delineating the retinal vascular. This provides a modern non-invasive retinal vascular imaging method compared to conventional dye-based imaging. High quality depth resolution of the superficial and deep capillary networks is possible on OCTA whereas this was not possible prior. OCTA may be limited by image quality degradation from factors such as motion artefact or media opacities, and therefore may not be the investigation of choice for all patient groups. There are multiple potential clinical applications for OCTA in retinal and choroidal vascular disease. Ongoing research is necessary to substantiate the more widespread use of OCTA due to its significant cost burden compared to current modalities.

A better study of the postnatal retinal development is not only essential for the in-depth understanding of the nature of the vision system but also may provide insights for treatment developments of eye conditions, such as retinopathy of premature (ROP). To date, quantitative analysis of postnatal retinal development is primarily limited to endpoint histological examination. This study is to validate in vivo optical coherence tomography (OCT) for longitudinal monitoring of postnatal retinal development in developing mouse eyes. Three-dimensional (3D) frame registration and super averaging were adopted to investigate the fine structure of the retina. Interestingly, a hyporeflective layer (HRL) between the nerve fiber layer (NFL) and inner plexiform layer (IPL) was observed in developing eyes and gradually disappeared with aging. To interpret the observed retinal layer kinetics, a model based on eyeball expansion, cell apoptosis, and retinal structural modification was proposed.

Optical coherence tomography (OCT) is one of the most promising, innovative and rapidly emerging intraoperative imaging modalities for neurosurgical guidance in brain tissue imaging, "optical biopsy", brain cerebral vascular detection, nerve fibers and white matter tracts detection. In this article, we provide a short survey of cross-polarization OCT and different types of OCT probes that can be used in routine neurosurgical practice. Through different types of probes there are multiple applications where OCT can play a highly complementary role in offering the real-time microscopic assessment and imaging of normal and pathological brain tissues. The biopsy-needle based probe for CP OCT was shown to be an effective instrument for brain tissue mapping and express estimation of tissue status as well as for detecting large blood vessels to prevent causing bleeding during biopsy sampling. The folded CP OCT probe for intraoperative use for brain tissue examination was shown as a potentially efficient sensor head for CP OCT. The probe demonstrated high lateral resolution in diffractive limited probing beam quality. The length of dismountable probe tip allows using the probe under operating microscope. Due to the designed family of specialized probes CP OCT fills in the niche of devices for express brain tissue examination in situ.

When a grid-forming (GFM) inverter is connected to a low or medium voltage weak power grid, the line impedance with resistive-inductive characteristics will cause power coupling. Typical GFM decoupling control strategies are designed under nominal line impedance parameters. However, there are deviations between the nominal line impedance and actual parameters, resulting in poor decoupling effects. Aiming at this problem, this paper proposes a power decoupling strategy based on a reduced-order extended state observer (ESO). Firstly, the power dynamic model of GFM is established based on the dynamic phasor method. Then, the model deviation and power coupling due to line impedance parameter perturbation are estimated as internal disturbances of the system, and the disturbances are compensated on the basis of typical power control strategy and virtual impedance decoupling. Good decoupling performance is obtained under different impedance parameters, improving the control strategy's robustness. Finally, the effectiveness of the proposed method is verified by the results of RT Box hardware-in-the-loop experiments.

This work presents a numerical study on atmospheric sound propagation over rough water surfaces. A method to generate pseudorandom sea profiles consistent with sea wave spectra is presented. The proposed method is suited to capture the logarithmic nature of the energy distribution of the waves. Sea profiles representing fully developed seas for sea states 2, 3, 4 and 5 are generated from the Elfouhaily et al. (ECKV) sea wave spectra. Excess attenuation caused by refraction and surface roughness is predicted with a parabolic equation (PE) solver. A novel method to estimate equivalent effective impedance based on PE predictions at different sea states is presented. Parametric expressions using acoustic frequency and significant wave height are developed for effective surface impedances. In this work, sea surface roughness is on a scale comparable to the acoustic wavelength. Under this condition, the acoustic scattering is primarily incoherent. This work shows the limitations of using an equivalent surface impedance in such incoherent scattering cases.

Static voltage stability has become one of the significant risks faced by large-scale renewable energy integration. However, traditional methods for static voltage stability analysis are often overly complex. This paper constructs an equivalent impedance model for renewable energy integrated distribution power systems, proposing a static voltage analysis method for renewable energy integrated distribution power systems based on impedance model index. This method has been verified to be applicable not only to renewable energy single-infeed system but also to multi-infeed system. Furthermore, an analysis is conducted on the influence of the integration capacity, location of renewable energy, and the topology of networks on impedance model index, indicating that a higher impedance model index corresponds to greater static voltage stability margins in the system. Hence, during the planning of renewable energy integration, the plan with the highest impedance model index should be selected. Finally, the accuracy of the analysis methods and conclusions in this paper was validated based on the IEEE 14-node system.

Ultra-wide field optical coherence tomography (UWF-OCT) has been recently introduced into clinical ophthalmological practice. To date, there is little data on the reference values of retinal thickness (RT) and choroidal thickness (CT) measured with this technique. This study aimed to analyze the variance of RT and CT in healthy eyes with UWF-OCT tests performed with the largest available scan size of 23 x 20 mm. The data were analyzed with reference to the patients' age, gender, and the axial length of the eyeball. The results of UWF-OCT scanning enabled us to picture the shape of the retina and choroid in a large portion of the eyeball. Both anatomical entities become significantly thinner at the periphery. The peripheral CT is greater in the upper and temporal sectors; the RT is higher in the nasal compared to the temporal sectors. Both choroid and retina lose thickness with age, however, CT and RT do not show a statistically significant correlation with the axial length after adjusting for age and gender. Age-related variations in thickness are especially prominent in the choroid. The CT in UWF-OCT testing is significantly greater in females while the RT is greater in males. UWF-OCT testing provides additional information on the anatomical structure of the retina and choroid compared to standard-field OCT

This article aims to detect lung cavitations using lung ultrasound (LUS) in a cohort of patients with pulmonary tuberculosis (TB) and correlate the findings with chest computed tomography (CT) and chest x-ray (CXR) to obtain LUS diagnostic sensitivity. Patients with suspected TB were enrolled after being evaluated with CXR and chest CT. A blinded radiologist performed LUS within 3 days after the admission at the Infectious Diseases Department. Finally, 82 patients were enrolled in the study. BAL confirmed TB in 58/82 (71%). Chest CT showed pulmonary cavitations in 38/82 (43.6%; 32 TB patients and 6 non-TB ones), LUS in 15/82 (18.3%; 11 TB patients and 4 non-TB ones) and CXR in 27/82 (33%; 23 TB patients and 4 non-TB ones). Patients with multiple cavitations were 12 detected at CT and only 1 at LUS. LUS sensitivity was 39.5%, specificity 100%, PPV 100%, NPV 65.7%. CXR sensitivity was 68.4% and specificity 97.8%. No false positive cases were found. LUS sensitivity is rather low as many cavitated consolidations do not reach the pleural surface. Aerated cavitations could be detected with LUS with relative confidence, highlighting a thin air-crescent sign towards the pleural surface within a hypoechoic area of consolidation, easily distinguishable from dynamic or static air-bronchogram.

Terahertz tomography is a promising method among non-destructive inspection techniques to detect faults and defects in dielectric samples. Image quality recently significantly improved through the incorporation of a priori information and off-axis data. However, this improvement has come at the cost of increased measurement time. To aim toward industrial applications, it is therefore necessary to speed up the measurement by parallelizing the data acquisition employing multi-channel setups. In this work, we present two tomographic frequency-modulated continuous wave (FMCW) systems working at a bandwidth of 230-320 GHz, equipped with an eight-channel detector array, and compare their imaging results with a single-pixel setup. While in the first system, the additional channels are used exclusively to detect radiation refracted by the sample, the second system features an f-θ lens, focusing the beam at different positions on its flat focal plane, and thus utilizing the whole detector array directly. The usage of the f-θ lens in combination with a scanning mirror eliminates the necessity of the formerly used slow translation of a single-pixel transmitter. This opens up the potential for a significant increase in acquisition speed, in our case by a factor of four to five, respectively.

The article presents the results of research on a new method of spatial analysis of walls and buildings moisture. Due to the fact that destructive methods are not suitable for historical buildings of great architectural significance, a non-destructive method based on electrical tomography has been adopted. A hybrid tomograph with special sensors was developed for the measurements. This device enables the acquisition of data, which are then reconstructed by appropriately developed methods enabling spatial analysis of wet buildings. Special electrodes that ensure good contact with the surface of porous building materials such as bricks and cement were introduced. During the research, a group of algorithms enabling supervised machine learning was analyzed. They have been used in the process of converting input electrical values into conductance depicted by the output image pixels. The conductance values of individual pixels of the output vector made it possible to obtain images of the interior of building walls, both flat intersections (2D) and spatial (3D) images. The presented group of algorithms has a high application value. The main advantages of the new methods are: high accuracy of imaging, low costs, high processing speed, ease of application to walls of various thickness and irregular surface. By comparing the results of tomographic reconstructions, the most efficient algorithms were identified.

This paper provides a comparative study between microwave tomography and synthetic time-reversal imaging techniques as applied to ground penetrating radar (GPR) surveys. The comparison is carried out by processing experimental data collected at a controlled test site, with various types of buried targets at given subsurface depths and representative soil conditions. It is shown that the two techniques allow us to obtain complementary information about position, depth and size of the targets from a single GPR survey.

The current state-of-the-art does not provide a universal and rapid method of determining the state of health (SOH) of a battery or a supercapacitor without carefully examining the degradation of hundreds of full charge/discharge cycles. Lithium-ion batteries, sodium-ion batteries and supercapacitors of different cell chemistries were studied by impedance spectroscopy during lifetime tests. Faradaic and capacitive charge storage are distinguished by the relationships between stored electric charge and capacitance. For batteries, impedance spectroscopy is best applicable in the flat region of the voltage-charge curve. An approximately linear correlation between pseudocapacitance and Ah capacity is observed as long as overcharge and deep discharge are avoided. The correct calculation of quantities related to complex impedance and differential capacitance is outlined – which may also be useful as an introductory text and tutorial for newcomers to the field. Novel diagram types are proposed for the purpose of instant performance and failure diagnosis of batteries and supercapacitors.

κ Draconis is a binary system with a classical Be star as the primary component. Its emission-line spectrum consists of hydrogen lines, notably the Hα line with a peak intensity ratio (V/R) variations phase-locked with the orbital period P = 61.55 days. Among binaries demonstrating the Be phenomenon, κ Dra stands out as one of a few systems with a discernible mass of its secondary component. Based on more than 200 spectra obtained in 2014 − 2023, we verified the physical parameters and constructed the mass function. We used part of these data obtained in 2014 − 2021 to investigate regions in the circumstellar disk of the primary component that emit the Hα line using the Doppler tomography method. The results show that the disk has a non-uniform density distribution with a prominent enhancement at Vy≈ 99 km s−1 and Vx≈−6 km s−1 that corresponds to a cloud-like source of the double-peaked Hα line profile. We argue that this enhancement’s motion is responsible for the periodic variations of the Hα V/R ratio, which is synchronised in orbital phase with the radial velocity (RV) of absorption lines from the atmosphere of the primary component.

Fractures of the talar neck and body are associated with spine fractures and scoliosis deformity, which affect cosmetic appearance and cause difficulty in ambulation. The implant design for talus surgery is thriving as a functional alternative in case of severe talar destruction, focusing on segmentation and reconstruction of the talus’s shape. However, manual segmentation of the talus is time-consuming and subjective. In this study we exploited the automatic segmentation framework to efficiently train a deep learning-based model to accurately segment the talus based on computed tomography imaging. We developed three model configurations with nnU-Net and investigated their Dice similarity coefficients (DSC) and 95% Hausdorff distances (HD95) for talus segmentation on a CT image dataset. The three configurations performed well (DSC > 0.95, HD95 < 0.6). When tested on the same samples, one of the configurations was more efficient while ensuring higher accuracy. We propose to focus on talus anatomic variations with increasing age based on this framework and apply it to clinical trials at the next stage.

Introduction: CT perfusion (CTP) is an alternative tool to assess cerebral hemodynamics in brain trauma. As traumatic acute subdural hematomas (ASH) are severe lesions commonly associated with poor outcome, we aimed to evaluate the brain hemodynamics in this population. Methods: Five patients admitted at the emergency department sustaining traumatic acute subdural hematoma were evaluated. Preoperative CTP was performed immediately after nonenhanced head CT scan. Postoperative CTP was performed in four patients. The outcome was assessed 6 months after surgery using the extended Glasgow Outcome Scale. Results: 4 male and 1 female were evaluated. Mean age was 46y (SD: 8.1). Mean preoperative midline brain shift was 10.1 mm (SD: 1.8). The main mechanism of trauma was falling (four patients). There was a general improvement in cerebral blood flow (CBF) after surgery from 23.9 (SD: 6.1) to 30.7 ml/100g/min, (SD: 5.1) and in mean transit time (MTT) from 7.3 (SD: 1.3) to 5.8s (SD:1.0), although it is not statistically significant (p=0.06 and p=0.06, respectively). There was still a reduction in the cerebral blood volume (CBV) media when compared to the value after surgery, from 2.63 (SD: 1.10) to 2.34 ml/100g (SD: 0.67), which is not statistically significant (p=0.31). Spearman correlation test of postoperative and preoperative CBF ratio with outcome was 0.94 (p=0.054). Only one patient died (three days after surgery). This patient was victim of car crash and had the highest preoperative MTT (9.97 seconds) and CBV (4.51 ml/100 g). Conclusion: Post-operative improvement of hemodynamic CTP parameters may be correlated with outcomes after ASH. Further studies with larger samples are required to confirm this hypothesis.

The ever-growing field of materials with applications in the biomedical field holds great promise regarding the design and fabrication of devices with specific characteristics especially scaffolds with personalized geometry and architecture. The continuous technological development pushes the limits of innovation in obtaining adequate scaffolds and establishing their characteristics and performance. To this end, computed tomography (CT) proved to be a reliable, non-destructive, high-performance machine, enabling visualization and structure analysis at sub-micronic resolutions. CT allows both qualitative and quantitative data of the 3D model, offering an overall image of its specific architectural features as well as reliable numerical data for rigorous analyses. The precise engineering of scaffolds consists in the fabrication of objects with well-defined morphometric parameters (e.g.: shape, porosity, wall thickness), and in their performance validation through thorough control over their behavior (in situ visualization, degradation, new tissue formation, wear, etc.). This review is focused on the use of CT in biomaterial science with the aim of qualitatively and quantitatively assess the scaffolds’ features and in monitoring their behavior following in vivo or in vitro experiments. Furthermore, the paper presents the benefits and limitations regarding the employment of this technique when engineering materials with applications in the biomedical field.

Several studies suggest that COVID-19 may be accompanied by symptoms such as a dry cough, muscle aches, sore throat, and mild to moderate respiratory illness. The symptoms of this disease indicate the fact that COVID-19 causes noticeable negative effects on the lungs. Therefore, considering the health status of the lungs using X-rays and CT scans of the chest can significantly help diagnose COVID-19 infection. Due to the fact that most of the methods that have been proposed to COVID-19 diagnose deal with the lengthy testing time and also might give more false positive and false negative results, this paper aims to review and implement artificial intelligence (AI) image-based diagnosis methods in order to detect coronavirus infection with zero or near to zero false positives and false negatives rates. Besides the already existing AI image-based medical diagnosis method for the other well-known disease, this study aims on finding the most accurate COVID-19 detection method among AI methods such as machine learning (ML) and artificial neural network (ANN), ensemble learning (EL) methods.

Background: Some studies have shown that an increase in visceral fat is associated with postoperative clinical and oncologic outcomes. However, no studies have used bioelectrical impedance analysis (BIA) to determine the effects of visceral fat on the oncologic outcomes of colorectal cancer (CRC). This study aimed to investigate the relationship between visceral fat area (VFA) and clinical, and oncologic outcomes in CRC. Methods: This study included 203 patients who underwent anthropometric measurements by BIA before surgical treatment for CRC between January 2016 and June 2020. Results: According to the cutoff level of VFA by receiver operating characteristic curve analysis, 85 (40.5%) patients had a low VFA, and 119 (59.5%) had a high VFA. Multivariate analysis found that preoperative CRP (hazard ratio [HR], 3.882; 95% confidence interval [CI], 1.001–15.051; p=0.050) and nodal stage (HR, 7.996; 95% CI, 1.414–45.209; p=0.019) were independent prognostic factors for overall survival, while sex (HR, 0.110; 95% CI, 0.013–0.905; p=0.040), lymphovascular invasion (HR, 3.560; 95% CI, 1.098–11.544; p=0.034), and VFA (HR, 4.263; 95% CI, 1.280–14.196; p=0.040) were independent prognostic factors for disease-free survival (DFS). Conclusion: High VFA preoperatively measured by BIA was associated with inflammations and was an independent prognostic factor for DFS.

The aim of the study was to compare the standard baseline imaging, with extended radiological staging. To assess our hypothesis, we performed a prospective, single-centre study which included 132 participants recruited between October 2015 and March 2020. Descriptive statistics, the Friedman and chi-squared tests were performed and p &lt; 0.05 was considered significant. Patients were grouped into two cohorts, CT scan cohort (n=87) and PET-CT cohort (n=43). In the first group the originally determined disease stage changed in 36.8 % of cases, in second group in 51.2 %. The consistency between assessment of axillary lymph nodes by imaging (cN) and the postoperative pathology report (pN) was evaluated. In most cases, clinical and pathological evaluation of involved nodes was consistent, for CT scan the result was χ2(1) = 18.98; p &lt; 0.001, for PET-CT the result was χ2(1) = 6.41; p = 0.03. Highly customized radiation therapy defined as dose boost within the involved lymph nodes, not covered by surgeon, was applied in nine patients.

Coronary angiography, long considered the gold standard for coronary imaging, faces limitations in assessing coronary vessel wall anatomy and guiding percutaneous coronary intervention (PCI). Despite its prevalence, studies have demonstrated that it is suboptimal in estimating the severity of coronary disease and physiologic significance of stenosis. Intracoronary imaging techniques, such as intravascular ultrasound (IVUS) and optical coherence tomography (OCT), offer promising alternatives to overcome these limitations. This review delves into the nuances of IVUS and OCT, highlighting their strengths and limitations as adjuncts to PCI. IVUS, utilizing ultrasound technology, and OCT, based on near-infrared light, each provide unique insights into coronary pathology. They differ in terms of temporal and spatial resolution, influencing their capabilities in plaque characterization and vessel assessment. The discussion navigates their historical evolution, technical specifications, and clinical utility. Meta-analyses and adjusted observational studies suggest that both IVUS and OCT-guided PCI correlate with reduced cardiovascular risks compared to angiographic guidance alone. While IVUS has demonstrated consistent benefits in terms of clinical outcomes, the evidence supporting OCT is less robust. However, the utilization of these imaging modalities remains variable across regions, with increasing adoption in recent years, particularly in IVUS-guided PCIs. Intravascular ultrasound's journey from early motion detection to current high-resolution mechanical systems is traced, including improvements in catheter size and compatibility. On the other hand, optical coherence tomography has advanced significantly, utilizing near infrared light to achieve unparalleled resolutions, albeit requiring temporary blood clearance for optimal imaging. In conclusion, IVUS and OCT offer valuable insights into coronary pathophysiology and guide interventions with improved precision compared to traditional angiography. While IVUS remains more extensively utilized, OCT's growing potential is underscored by advancements in technology, culminating in enhanced imaging capabilities. Both modalities demonstrate comparable clinical outcomes, emphasizing the need for tailored imaging choices based on individual clinical scenarios. The continued refinement and broader integration of intravascular imaging are expected to play a pivotal role in optimizing coronary interventions and patient outcomes.

.Purpose: This paper presents a comparative analysis of state-of-the-art DIR algorithms in the context of head and neck squamous cell carcinoma (HNSCC) radiation therapy. Materials and Methods: We used a dataset of head and neck cancer patients within the Cancer Image Archive, which includes 31 patients with 3D CT image data from pre-treatment, mid-treatment, and post-treatment stages of radiotherapy. We applied DIR algorithms to two datasets, one for pre-treatment to mid-treatment registration and another for mid-treatment to post-treatment registration, by aligning one CT image to another CT image. To quantitatively analyze the patient data, we focused on the spinal cord, optic nerve, brain stem, cochlea, and PTV as the OAR datasets. To verify the DIR algorithm, we used two non-learning-based methods, SyN and NiftyReg, as well as three deep learning-based methods, Voxelmorph, Cyclemorph, and Transmorph. We trained a deep learning model by adjusting the ratio of the training dataset, validation dataset, and test dataset to 7:1:2. Results: The average DSCs of SyN and NiftyReg, the non-learning-based methods, were 0.74±0.06 and 0.70±0.12, respectively. The deep learning-based methods, Voxelmorph, Cyclemorph, and Transmorph, had average DSCs of 0.72±0.08, 0.68±0.11, and 0.69±0.13, respectively. The deep learning DIR algorithm produced transformed outputs of OAR/PTV in a shorter time than other models, including commercial and conventional mathematical algorithms (At Inference(sec/images), Voxelmorph: 0.36, Cyclemorph: 0.3, Transmorph: 5.1, SyN: 140, NiftyReg: 40.2). Conclusions: In conclusion, our study provides a comprehensive comparison of commercial DIR algorithms with traditional and deep learning-based DIR methods. Our results demonstrate that commercial DIR algorithms outperform traditional DIR methods in terms of accuracy and efficiency. However, we also show that deep learning-based DIR methods have the potential to achieve similar performance to commercial algorithms with proper training and optimization. Our findings suggest that both commercial and deep learning-based DIR methods have their respective advantages and limitations, and the choice of method should depend on the specific requirements of the clinical application. Overall, our study contributes to ongoing efforts to improve the accuracy and efficiency of DIR methods for better patient outcomes.

Background: As coronavirus (COVID-19) continues to pose a threat to the entire world, it is critical to developing strategies for containing its spread. The purpose of this study was to assess the demographic characteristics, brain tomography characteristics, and diffusion magnetic resonance findings of COVID-19 positive individuals. Material and Method: Between January 1 and December 31, 2021, 317 patients over the age of 18 were admitted to the emergency department with symptoms consistent with COVID-19. Three groups were formed based on clinical findings in patients, divided into light, medium, and severe, and four groups were formed based on radiological imaging findings. Results: The mean age of the 317 patients included in the study was 67.28±12.06 years, with a range of 28-91 years. The clinical classification of the patients was based on laboratory parameters and radiological imaging, not on their age or gender. Mild cases were classified as CO-RADS 0-4; moderate and severe cases were classified as CO-RADS 5-6 (p=0.001). While 60 (18.9%) of patients were followed outpatient, 144 (45.4%) were admitted to the hospital, 73 (23%) were admitted to the intensive care unit, and 40 (12.7%) died (p=0.001). Direct radiographs revealed bilateral involvement in 224 (70.7%) cases, peripheral involvement in 259 (81.7%) cases, and mid-lower lobe lung involvement in 194 (61.2%) cases (p=0.001). Brain tomography revealed infarction in 42 (13.2%) of the patients who were followed and hospitalized and hemorrhage in 22 (6.9%) of the patients. Magnetic resonance imaging revealed diffusion involvement in 68 (21.5%) of the cases (p=0.001). Conclusion: A standardized reporting system for COVID-19 data is required, and it must be simple to use, quick to understand, and focused on determining the risk of pneumonia. Additionally, the diagnostic role of radiological imaging, prognosis prediction, and severity scoring of lung involvement should be included.

Defectively manufactured and deliberately damaged composite laminates fabricated with different continuous reinforcing fibres (respectively, carbon and glass) and polymer matrices (respectively, thermoset and thermoplastic) were inspected in magnetic resonance imaging equipment. Two pulse sequences were evaluated during non-destructive examination conducted in saline solution-immersed samples to simulate load-bearing orthopaedic implants permanently in contact with biofluids. The orientation, positioning, shape, and especially the size of translaminar and delamination fractures were determined according to stringent structural assessment criteria. The spatial distribution, shape, and contours of water-filled voids were sufficiently delineated to infer the amount of absorbed water if thinner image slices than this study were used. The surface texture of composite specimens featuring roughness, waviness, indentation, crushing, and scratches was outlined, with fortuitous artefacts not impairing the image quality and interpretation. Low electromagnetic shielding glass fibres delivered the highest, while electrically conductive carbon fibres produced the poorest quality images, particularly when blended with thermoplastic polymer, though reliable image interpretation was still attainable.

The present work analyzes the behavior in terms of corrosion resistance of three reinforced concrete formulations over a period of 1 year. The samples were accompanied by creating a monitoring methodology using the Electrochemical Impedance Spectroscopy (EIE) technique, working only with the real component over time. Three mixtures were used, one conventional without pozzolanic addition (REF) and two others with pozzolanic additions, rice husk ash (RCA) and metakaolin (MK). Prototypes were created and exposed to the action of a 165g/l NaCl sodium chloride solution. The characterization of the materials was carried out by determining the chloride diffusion profile (ASTM 1556), analyzing images using tomography and with the support of analytical techniques such as x-ray fluorescence and x-ray diffraction. The monitoring methodology using the EIE demonstrated the positive effect of the insertion of pozzolans, rice husk ash (RCA) and metakaolin (MK), by delaying the process of chloride diffusion in the concrete, resulting in greater resistance to corrosion. The EIE also showed that the active mineral addition in concrete, of aluminum-silicic composition (MK), had a predominant protective effect on the steel//concrete interface against the attack of chloride ions.

The authors attempt to addresses the importance of timely detection and management of cervical intraepithelial neoplasia (CIN) to prevent cervical cancer. The study focuses on the potential of electrical impedance spectroscopy (EIS) as an adjunct to colposcopy, aiming to enhance the accuracy of identifying high-grade cervical lesions. Colposcopy, a widely used technique, exhibits variable sensitivity in detecting high-grade lesions, which relies on the expertise of the operator. The study's primary objective is to evaluate the effectiveness of combining colposcopy with EIS in detecting high-grade cervical lesions among patients initially diagnosed with low-grade CIN based on cytology. We employ a cross-sectional observational design, recruiting 101 women with abnormal cervical cytology results. The participants undergo colposcopy with acetic acid and subsequent EIS using the ZedScan device. The ZedScan results are categorized into color-coded probability levels, with red indicating the highest likelihood of high-grade squamous intraepithelial lesions (HSIL) occurrence. Results reveal that ZedScan exhibits a sensitivity rate of 89.5% and a specificity rate of 84% for detecting high-grade lesions. Colposcopy, on the other hand, records a sensitivity rate of 85.5% and a specificity rate of 92%. The agreement rate between ZedScan and biopsy is 79.2%, as indicated by a kappa coefficient of 0.71, while the agreement rate between colposcopy and biopsy is 74.3%, with a kappa coefficient of 0.71.

Contrast agents developed for X-ray computed tomography (CT) offer extremely valuable tools and techniques in diagnostics via contrast enhancements. Heavy metal-based nanoparticles (NPs) can provide high contrast in CT images. These result from a high density of heavy metal atoms with high X-ray attenuation coefficients that exceed that of iodine (I), which is currently used in hydrophilic organic CT contrast agents. Nontoxicity and colloidal stability are vital characteristics in designing heavy metal-based NPs as CT contrast agents. In addition, the particle size must be small for in vivo renal excretion. In vitro phantom imaging studies can provide X-ray attenuation efficiency, which is a critical parameter for CT contrast agents, and the imaging performance of CT contrast agents can be demonstrated via in vivo experiments. This review focuses on in vitro and in vivo studies of various heavy metal-based NPs (metal: Au, Pt, Pd, Ag, Ce, Gd, Dy, Ho, Yb, Ta, W, and Bi) and provides an outlook on their use as high-performance CT contrast agents.

Coronary optical coherence tomography (OCT) is an intravascular, near-infrared light-based imaging modality capable of reaching axial resolutions of 10-20 µm. This resolution allows for accurate determination of high-risk plaque features, such as thin cap fibroatheroma; however, visualisation of morphological features alone still provides unreliable positive predictive capability for plaque progression or future major adverse cardiovascular events (MACE). Biomechanical simulation could assist in this prediction, but this requires extracting morphological features from intravascular imaging to construct accurate three-dimensional simulations of patients’ arteries. Extracting these features is a laborious process, often carried out manually by trained experts. To address this challenge, numerous techniques have emerged to automate these processes while simultaneously overcoming difficulties associated with OCT imaging, such as its limited penetration depth. This systematic review summarises advances in automated segmentation techniques from the past five years (2016-2021) with a focus on their application to the three-dimensional reconstruction of vessels and their subsequent simulation. We discuss four categories based on the feature being processed, namely: coronary lumen; plaque characteristics and subtypes; artery layers; and stents. Areas for future innovation are also discussed as well as their potential for future translation.

Early detection improves prognosis in pancreatic ductal adenocarcinoma (PDAC) but is challenging as lesions are often small and poorly defined on contrast-enhanced computed tomography scans (CE-CT). Deep learning can facilitate PDAC diagnosis, however current models still fail to identify small (&lt;2cm) lesions. In this study, state-of-the-art deep learning models were used to develop an automatic framework for PDAC detection, focusing on small lesions. Additionally, the impact of integrating surrounding anatomy was investigated. CE-CT scans from a cohort of 119 pathology-proven PDAC patients and a cohort of 123 patients without PDAC were used to train a nnUnet for automatic lesion detection and segmentation (nnUnet_T). Two additional nnUnets were trained to investigate the impact of anatomy integration: (1) segmenting the pancreas and tumor (nnUnet_TP), (2) segmenting the pancreas, tumor, and multiple surrounding anatomical structures (nnUnet_MS). An external, publicly available test set was used to compare the performance of the three networks. The nnUnet_MS achieved the best performance, with an area under the receiver operating characteristic curve of 0.91 for the whole test set and 0.88 for tumors &lt;2cm, showing that state-of-the-art deep learning can detect small PDAC and benefits from anatomy information.

Dental pulp chamber volume is a fundamental measurement in the field of endodontics, but also in forensic sciences, teaching and training, or tissue engineering. This study evaluates the precision of cone beam computed tomography (CBCT) in comparison with computed micro-tomography (micro-CT) in evaluating pulp chamber volume of upper central incisors ex vivo. The intra-operator and inter-operator error were evaluated, and the results for the two techniques were compared with a T-test for paired samples. Intra-operator and inter-operator errors were >0.05, indicating an adequate reproducibility in each operator and no significant differences between their meas-urements. On the other hand, no significant differences between the two measurement techniques. The present results demonstrate that CBCT is a precise, feasible and reproducible technique for evaluation of dental pulp chamber volume ex vivo. Results provided with this method are suitable for different medical branches but also for teaching and training of undergraduate and post-graduate students. Furthermore, the findings of this study carry significant clinical implications, as accurate assessment of pulp chamber volume is critical in the diagnosis and treatment of various endodontic conditions. The ability of CBCT to provide reliable 3D dental anatomy measurements can enhance the planning of endodontic treatments by allowing for a better understanding of internal tooth morphology. Additionally, the precision and reproducibility of CBCT in assessing pulp chamber volume can contribute to improved clinical outcomes and reduced complications during endodontic procedures. These findings further support the increasingly vital role of CBCT in modern clinical practice and underscore its value as an indispensable tool in the field of dentistry.

A surgical technique aimed at rerouting aqueous humor (AH) outflow from the anterior chamber to the suprachoroidal space (SCS) without performing surgical cyclodialysis was developed to decrease intraocular pressure (IOP) in glaucoma patients. The surgical outcomes of the technique were retrospectively analyzed in fifty-eight patients. At 6, 12, and 24 months, the mean IOP decreased from 27.8±8.3 to 14.95.0 mmHg, median 15.0 (25th percentile (p25 )13.0; 75th percentile (p75) 18.0), and 15.23.3 mmHg; hypotensive medication use reduced from median (p25; p75) 3 (2; 3) to 0 (0; 2), 0 (0; 2), and 0 (0; 1.5), and complete success was achieved in 62.8%, 51.2%, and 32.5% cases, with partial success in 28.4%, 44.2%, and 62.5% cases, respectively. Eight cases (13.8%) presented unsatisfactory outcomes. Intra- and postoperative complications were few and manageable. No bleb formation was observed in any of the cases. In 50% of cases, conjunctival lymphatic vessels (CLVs) developed following surgery in superior quadrants. The technique is safe and effective in providing a long-term decrease in IOP and hypotensive medication use. It was hypothesized in this study that the IOP decrease occurred as a result of enhanced AH outflow from the SCS to CLVs through intrascleral microchannels connecting the SCS to CLVs.

Abstract: Comparing outcrop data to laboratory results is important to verify and validate experiments of analogue and reservoir materials especially regarding conditions for deformation experiments. This is important better understand highly complex carbonate reservoir strata and their response to changes in subsurface conditions, reducing subsurface uncertainty. This study develops methods to allow for a more straightforward comparison of outcrop data (m-scale) with experimentally created fracture arrays developed in cylindrical samples (cm-scale). The main objective is to assess usefulness of experimentally-produced fracture networks as analogues for subsurface structures, typically at the meter and above scale by developing new techniques to use the lab deformation. It analyses key characteristics of laboratory-induced fracture networks by adapting scanline methods to use with x-ray tomography (XRT) images to allow for comparison with outcrop and field data. To test and verify these new methods two low permeability carbonate samples were used for deformation testing and analysis. Applying the different scanline methods we show that they can be used to analyse lab induced fractures (mm to cm-scale) identified in XRT images for comparison with outcrop data (m-scale). In addition, these methods also allow for quantification of fracture network attributes e.g. fracture spacing, fracture apertures, orientation. This new data bridges the gap between micro-scanlines using thin sections and outcrop scanlines.

Background: Appendicular skeletal muscle (or lean) mass (ALM) estimated using dual-energy X-ray absorptiometry (DXA) is considered to be a preferred method for sarcopenia studies. However, DXA is expensive, has limited portability, and requires radiation exposure. Bioelectrical impedance analysis (BIA) is inexpensive, easy to use, and portable; thus BIA might be useful in sarcopenia investigations. However, a large variety of models have been commercially supplied by different companies, and for most consumer products, the equations estimating ALM are not disclosed. It is therefore difficult to use these equations for research purposes. In particular, the BIA equation is often age-dependent, which leads to fundamental difficulty in examining age-related ALM loss. The aims of the current study were as follows: (1) to develop and validate an equation to estimate ALM using multi-frequency BIA (MF-BIA) based on theoretical models, and (2) to establish sarcopenia cutoff values using the equation for the Japanese population. Methods: We measured height (Ht), weight, and ALM obtained using DXA and a standing-posture 8-electrode MF-BIA (5, 50, 250 kHz) in 756 Japanese individuals aged 18 to 86-years-old (222 men and 301 women as developing equation group and 97 men and 136 women as a cross validation group). The traditional impedance index (Ht²/Z₅₀) and impedance ratio of high and low frequency (Z₂₅₀/Z₅) of hand to foot values were calculated. Multiple regression analyses were conducted with ALM as dependent variable in men and women separately. Results: We created the following equations: ALM = (0.6947 × (Ht²/Z₅₀)) + (−55.24 × (Z₂₅₀/Z₅)) + (−10,940 × (1/Z₅₀)) + 51.33 for men, and ALM = (0.6144 × (Ht²/Z₅₀)) + (−36.61 × (Z₂₅₀/Z₅)) + (−9332 × (1/Z₅₀)) + 37.91 for women. Additionally, we conducted measurements in 1624 men and 1368 women aged 18 to 40 years to establish sarcopenia cutoff values in the Japanese population. The mean values minus 2 standard deviations of the skeletal muscle mass index (ALM/Ht²) in these participants were 6.8 and 5.7 kg/m² in men and women, respectively. Conclusion: The current study established and validated a theoretical and age-independent equation using MF-BIA to estimate ALM and provided reasonable sarcopenia cutoff values.

Background: The Sequential Organ Failure Assessment (SOFA) is a scoring system used for the evaluation of disease severity and prognosis of critically ill patients. The impedance ratio (Imp-R) is a novel mortality predictor. Aims: This study aimed to evaluate the combination of SOFA + Imp-R in the prediction of mortality in critically ill patients admitted to the emergency department (ED). Methods: A retrospective cohort study was performed in adult patients with acute illness admitted to the ED of a tertiary-care referral center. Baseline SOFA score and bioelectrical impedance analysis to obtain the Imp-R were performed within the first 24 hours after admission to the ED. A Cox regression analysis was performed to evaluate mortality risk of initial SOFA score plus Imp-R. Harrell's C-statistic and decision curve analyses (DCA) were performed. Results: Out of 325 patients, 240 were included for analysis. Overall mortality was 31.3%. Only 21.3% of non-surviving patients died after hospital discharge, and 78.4% died during hospital stay. Of the latter, 40.6% died in the ED. SOFA and Imp-R values were higher in non-survivors and were significantly associated with mortality in all models. The combination of SOFA + Imp-R significantly predicted 30-day mortality, in-hospital mortality, and ED mortality with area under the curve (AUC) of 0.80 (95% CI: 74-0.86), 0.79 (95% CI: 0.74-0.86) and 0.75 (95% CI: 0.66-0.84) respectively. The DCA showed that combining SOFA + Imp-R improved the prediction of mortality through the lower risk thresholds. Conclusion: The addition of Imp-R to baseline SOFA score at admission to the ED improves mortality prediction in severely acutely ill patients admitted to the ED.

We aimed to directly compare the cost-effectiveness of the NELSON and NLST screening protocols, two trials influencing lung cancer screening implementation internationally. A decision-analytic model analyzing the cost-effectiveness of the NELSON protocols was manipulated to reflect the protocols of the NLST, while maintaining features specific to the Hungarian healthcare setting. In the NELSON protocol, there are three possible outcomes to the initial round of screening: positive, negative, or indeterminate, indicating an uncertain degree of suspicion for lung cancer. This pro-tocol differs from the NLST protocol, in which the only possible screening outcomes are positive or negative, with no indeterminate option. The NLST pathway for smokers aged 55-74 resulted in a 43 € increase in total average lifetime costs compared to the Hungarian screening pathway and re-sulted in a lifetime gain of 0.006 QALYs. The incremental costs and QALYs yield an ICER of 7875 €/QALY. Our results demonstrate that assigning any suspicious LDCT screen as a positive result (NLST protocol) rather than indeterminate (NELSON protocol) can yield a slight QALY gain that is worth the additional use of resources according to Hungary’s willingness to pay threshold. Our study provides insight on the cost-effectiveness, advantages, and disadvantages of various LDCT screening protocols for lung cancer and can assist other countries as they implement their screening programs.

The accurate and timely assessment of lymph node involvement is paramount in the management of patients with malignant tumors, owing to its direct correlation with cancer staging, therapeutic strategy formulation, and prognostication. Dual-energy computed tomography (DECT), as a burgeoning imaging modality, has shown promising results in the diagnosis and prediction of preoperative metastatic lymph nodes in recent years. This article aims to explore the application of DECT in identifying metastatic lymph nodes (LNs) across various cancer types, including but not limited to thyroid carcinoma (focusing on papillary thyroid carcinoma), lung cancer, and colorectal cancer. Through this narrative review, we aim to elucidate the clinical relevance and utility of DECT in the detection and predictive assessment of lymph node metastasis in malignant tumors, thereby contributing to the broader academic discourse in oncologic radiology and diagnostic precision.

Background: Computed tomography examinations have produced high radiation doses to patients, especially the CT brain. This study aimed to optimize the radiation dose and image quality in adult CT brain protocol. Materials and Methods: Images were acquired by Catphan 700 phantom. Radiation doses were recorded as CTDIvol and dose length product (DLP). CT brain protocols were optimized by varying parameters such as kVp, mAs, signal-to-noise ratio (SNR) level, and Clearview iterative reconstruction (IR). Image quality were also evaluataion by The AutoQA Plus software. Results: CT Number accuracy and linearity had a robust positive correlation with the linear attenuation coefficient (µ) and showed more inaccurate CT numbers when using 80 kVp. MTF showed a higher value in 100 and 120 kVp protocols, while high contrast spatial resolution showed a higher value in 80 and 100 kVp protocols. Low contrast detectability and CNR tended to increase when using high mAs, SNR and Clearview IR protocol. Noise decreased when using a high radiation dose and a high percentage of Clearview IR. CTDIvol and DLP were increased with increasing kVp, mAs, and SNR levels, while the increasing percentage of Clearview did not affect the radiation dose. Conclusion: Optimized protocols, including radiation dose and image quality, should be evaluated to preserve diagnostic capability. The recommended parameter settings include kVp set between 100-120 kVp, mAs ranging from 200-300 mAs, SNR level within the range of 0.7-1.0, and an iterative reconstruction value of 30% Clearview to 60% or higher.

Wild-type p53 cancer therapy-induced senescent cells frequently engulf and degrade neighboring ones inside a massive vacuole in their cytoplasm. After clearance of the internalized cell, the vacuole persists, seemingly empty, for several hours. Despite large vacuoles being associated with cell death, this process is known to confer a survival advantage to cancer engulfing cells, leading to therapy resistance and tumor relapse. Previous attempts to resolve the vacuolar structure and visualize their content using dyes were unsatisfying for lack of known targets and ineffective dye penetration and/or retain. Here, we overcame this problem by applying optical diffraction tomography and Raman spectroscopy to MCF7 doxorubicin-induced engulfing cells. We demonstrated a real ability of cell tomography and Raman to phenotype complex microstructures, such as cell-in-cells and vacuoles, and detect chemical species in extremely low concentrations within live cells in a completely label-free fashion. We show that vacuoles had a density indistinguishable to the medium, but were not empty, instead contained diluted cell-derived macromolecules, and we could discern vacuoles from medium and cells using their Raman fingerprint. Our approach is useful for the non-invasive investigation of senescent engulfing (and other peculiar) cells in unperturbed conditions, crucial for a better understanding of complex biological processes.

In birds, unlike mammals, there is no complete separation between the thoracic and abdominal cavities. Instead, they have the coelomic cavity where most main organs are found. Therefore, an adequate knowledge of the anatomy of the coelomic cavity is of great importance for veterinarians, biologists and the scientific community. This study aimed to evaluate the coelomic cavity anatomy in the Atlantic puffins (Fratercula Arctica) using anatomical sections and computed tomography images.

Objectives: The current study aimed to compare the adaptation of the restored class-I cavities with two self-etch adhesives bonded to two resin composite using cross-polarization optical coherence tomography (CP-OCT). Materials and Methods: Cylindrical class-I cavities were prepared on twenty, extracted human premolars. Two self-etch adhesives; Clearfil SE bond 2 (SE; Kuraray Noritake Dental, Japan) and Bond Force (Palfique Bond) adhesive (PL; Tokuyama Dental, Japan) were used in this study that were bonded to either resin composites materials; Herculite XRV microhybrid dental composite (HRV; Kerr, Italy) or Estelite Alpha composite (ESA; Tokuyama Dental, Japan). The specimens were divided into four groups (n=5); SE-HRV, SE-ESA, PL-HRV and PL-ESA. All specimens were varnished and stored in distilled water for 24h. Then, they were submerged in a contrasting medium. After that, all groups were optically imaged under CP-OCT at every 250 µm interval distance. Later, image binarization and gap quantification were carried out using Image analysis software. Result: There was a significant difference between all the groups except between SE-ESA and PL-ESA (p = 0.51). The highest median gap % was seen in PL-HRV group followed by SE-ESA, PL-ESA and SE-HRV. Conclusion: Other than composite filler loading and adhesive formula, the interactions of the adhesive and composite copolymers have great influence on composite adaptation.

Introduction Cone Beam Computed Tomography (CBCT) scans should be digitally oriented using a reference plane before being evaluated for patient growth and treatment outcome. Current orientation planes are usually dependent on the Porion points. Using more reliable landmarks than the Porion, we introduce the Acta plane and investigate its reliability as an alternative reference plane for cases in which the Porion point is inaccessible. Methods To test its reliability, a dental student and an orthodontist located sixteen skeletal and dental landmarks in sixteen CBCT scans, before and after reorientation. Also, four measurements were calculated based on these landmarks’ coordinates. The reorientation of these CBCT scans with the Acta plane was done by another dental student. Intraclass Correlation Coefficient (ICC) was calculated before and after orientation, intra- and inter-examiner. The data were tested for significance through the Shapiro Wilk test with a threshold set at 0.05. Through the ICC variation of the points’ coordinates, this article also evaluated the reliability of this plane with the t-paired and exact-sign tests. Results: The identification of landmarks was more reliable in the reoriented CBCT images than in the original images, with a significant increase of 0.012 in the median of the ICC. Linear and angular measures showed no significant differences between groups. Conclusion This plane is a reliable alternative for the orientation of CBCT images. The design of the Acta plane might allow the use of a smaller field of view and, consequently, a reduction in the radiation dose.

Conclusions: HRCT is a valuable tool in preoperative assessment of cholesteatoma, helping in making surgical decisions. It can accurately predict the extent of disease and is helpful for detecting unapparent dangerous situations. However it is not very accurate in detecting Fallopian canal and stapes erosion.

ABC-OCT, Affordable B-scan Camera-based Optical Coherence Tomography, implements Fourier-Domain Optical Coherence Tomography with real-time display using cross-platform C++ and the OpenCV framework. The software can be compiled using current versions of GCC for *nix/Mac and Microsoft^® Visual Studio for Windows. Full functionality of ABC-OCT needs the camera SDK from QHYCCD and a QHYCCD camera to be connected; but the code can be easily modified to support other camera drivers, as is shown by an included demo version which can use any installed webcam. The code is made available under the MIT license. The software is available from GitHub (https://github.com/hn-88/FDOCT).

Background: Coronavirus disease 2019 (COVID-19) remains a mystery in many respects. The importance of less common life-threatening diseases is still unclear. Therefore, in this study, it was attempted to determine the frequency of nontraumatic hemothorax, chylothorax, pleural, and pericardial effusion (PCE) in patients who underwent thoracic computed tomography during the pre-pandemic and pandemic period. Materials and Methods: This retrospective study included 147 patients over the age of 18 who were admitted to the emergency department between January 1st, 2019, and December 31st, 2020. The year 2019 was taken as the pre-pandemic period and the year 2020 was the pandemic period. Comorbidity, survival, and laboratory parameters of the patients were evaluated. Results: The mean age of the 147 patients included in the study was 66.41 ± 12.81 years, 54 (36.7%) were female, and the age range was 22–88 years. The mean plasma lactate dehydrogenase (LDH) level of the patients was 373.97 ± 115.77 U/L, plasma protein was 5.45 ± 1.00 gr/dL, fluid LDH was 229.37 ± 125.73 U/L, fluid/plasma LDH was 0.60 ± 0.23, fluid/plasma protein was 0.55 ± 0.29, and the amount of fluid discharged was 562.11 ± 243.01 mL. Bilateral lung involvement was present in 72 (49%) patients, and coagulation use was present in 59 (40.1%) patients. Pleural effusion (PE) was found in 43 (76.8%) of the hospitalized patients, hemothorax in 11 (19.6%) patients, and chylothorax in 4 (7.1%) patients. However, PCE was more common in the 16 (42.1%) patients admitted to the intensive care unit (ICU) (P < 0.001). While 38 (25.9%) of the patients were admitted to the ICU, mortality was observed in 30 (20.4%) patients. Conclusion: Although PE, nontraumatic hemothorax, chylothorax, and PCE are rare in COVID-19 patients, they can cause severe inflammation and poor prognosis.