The variability of the material properties of steel from different suppliers causes problems in achieving the required surface quality after turning. Therefore, the manufacturer needs to be able to estimate the resulting quality before starting production, especially if it is an expensive, small-batch production from stainless steel. Predictive models will make it possible to estimate the surface roughness from the mechanical properties of steel in the Mill Test Certificate (MTC) and thus support decision-making about the supplier selection or the acceptance of a material supply. Multivariate second-order polynomial model and feedforward back-propagation Artificial Neural Network (ANN) model were used to enhance the methodological robustness in formulating the decision if the predicted surface roughness is outside the required range, even before accepting the delivery. Both models can accurately predict surface roughness, while the ANN model is more accurate than the polynomial model; however, the predictive model is sensitive to the accuracy of the input data, and the model’s prediction is valid only under precisely defined conditions. The prediction model is used in a step-by-step decision-making procedure, which enables the trained staff to make a quick decision.

The paper portrays predictive models for dissolved oxygen (DO) levels in an urban lake using common water quality parameters like Temperature, pH, Conductivity and ORP at a time. Data were sampled using three real-time, industry-standard sensors, OPTOD, CTZN, and PHEHT, and then interpolated using the ArcGIS kriging technique. Correlation studies were analyzed through the ML algorithm, the correlation study signified a highly positive correlation between DO and other water parameters and the model was corroborated by R-score in order to create the linear regression model. In addition, an artificial neural network- a machine learning method using the Levenberg-Marquardt algorithm was developed to build a model to predict the do as well. Then, the performance of the models was validated and also the R² accuracy was checked of the predicted data against the actual data. Thus, the appropriateness of the ANN model for the forecasting of investigated attributes is indicated by the fact that the discrepancy between the forecasted and real ANN model is significantly lesser than that of the regression model. However, the model can be used to reveal DO data from unknown urban lake water.

A contemporary technique for calculating seismic risk is earthquake nowcasting (EN), which analyzes the progression of the earthquake (EQ) cycle in fault systems. 'Natural time' is a novel idea of time that serves as the foundation for EN assessment. The earthquake potential score (EPS), which has been discovered to have useful uses regionally and worldwide, is a unique tool EN uses to predict seismic risk. For the estimation of the EPS for the occurrences with the highest magnitude among these applications, we have since 2021 concentrated on Greece territory, applying sophisticated Artificial Intelligence (AI) algorithms, both wise (semi)supervised and unsupervised models, along with a customized dynamic sliding window technique that performs as a stochastic filter able to fine-tune the geo seismic occurrences. Long short-term memory (LSTM) neural networks, random forests, and clustering (geospatial) models are three machine learning techniques that are particularly good at finding patterns in vast databases and may be used to enhance earthquake prediction performance. In this study, we attempt to forecast whether practical Machine-learning and AI/Game-theoretic-based approaches can help predict big earthquakes and the normal future seismic cycle for 6-12 months. Specifically, we focus on answering two questions for a given region: (1) Is there a chance that a significant earthquake—say, one with a magnitude of M ≥ 6.0 will happen in the upcoming year? (2) What is the largest earthquake magnitude predicted in the upcoming year, and with which exact geographic coordinates (GCS)? Our results are quite promising and project a high precision accuracy score (≥ 98%) for seismic nowcasting in terms of four predictive parameters: the approximate (a) latitude, (b) longitude, (c) focal depth, and (d) magnitude of the phenomena.

This paper attempts to compare two different approaches to solve the problem of accident rates prediction based on human factors for industrial workers. One of the methods has already been done using Fuzzy c-Means Clustering and proved to be working with decent results. The second method which will be covered in this paper is using Artificial Neural Networks. The primary goal of this work is to insure that ANN will work efficiently in such prediction problem. The second goal is to reveal the fact that which one of the two selected methodologies is better at defining the estimation of accident rates among people who work in different industrial fields. The purpose has been achieved when the outcome of the ANN was obtained and compared accordingly with the output of the research previously carried out with Fuzzy c-means clustering method. Comparing the outcomes of these two different methods gave an immense insight on which features are more important than others when it comes to laborers properties with completely different background such as varying levels of health, knowledge, experience, training and physical properties. At the end of the research, it becomes clear that accident rates estimation for laborers with properly trained Artificial Neural Network gives better results when it is compared with Fuzzy c-Means Clustering method. Standard deviation method was used to calculate the validity of ANN technique. The result was compared with Fuzzy c-mean clustering technique. Impressive improvement of 8.8% in the accident rate prediction was achieved using Tailored-Made-ANN.

For years, effort has been devoted to establishing an effective bull breeding soundness evaluation procedure; usual research on the subject is based on BBSE (Bull Breeding Soundness Examination) methodologies, which have significant limitations in terms of their evaluation procedure, such as high cost, time-consuming and administratively difficult. This research focuses on the creation of a prediction model to supplement and/or improve the BBSE approach, through the study of two algorithms, Clustering and Artificial Neural Network (ANN), to find the optimum Machine Learning (ML) approach for our application, with an emphasis on data categorization accuracy. The tool is designed to assist veterinary medicine and farmers in identifying key factors and increasing certainty in their decision-making during the selection of bulls for breeding purposes, providing data from a limited number of factors generated from a deep pairing study of bulls. Zebu Bulls, European Bulls, and Crossbred Bulls were the general groupings. The data utilized in the model's creation (N =359) considers five variables that influence improvement decisions. This approach enhances decision-making by 12%. ANN obtained an accuracy of 90%; Precision was 97% for satisfying, 92% for unsatisfying, and 85% for Bad.

Healthcare professionals constantly face situations that reflect ecosystems’ degradation. These can negatively affect their mental health. Research suggests that hope and resilience can play an important role in this scenario, since they are related to/predict mental health in highly heterogeneous samples (considering geography, age, profession, health, etc.). In this context, the aims of the present study are: to characterize and explore the relationship between hope, resilient coping and mental health of Portuguese healthcare professionals. Using Google Forms, 276 healthcare professionals answered to the GHQ-28, the (adult) Trait Hope Scale, and the Brief Resilient Coping Scale (cross-sectional study). The minimum and maximum possible scores were reached, with the exception of the maximum score of GHQ-28-Total. Regarding Hope, 19.6% scored below the midpoint (M=43.46, SD=11.97); 29.3% revealed low resilience (M=14.93, SD=4.05); and the average of 4 of the 5 Mental Health scores (exception: Severe Depression) indicates the probability of a psychiatric case. Hope correlated with Social Dysfunction and GHQ-28-Total; resilient coping proved to be a (weak) predictor of 4 of the 5 GHQ-28 indicators (exception: Severe depression). The results support the need to promote the sample's mental health, hope and resilient coping. They also suggest that stimulating resilient coping may contribute to improving healthcare professionals’ mental health.

Recognition of the human interaction on the unconstrained videos taken from cameras and remote sensing platforms like a drone is a challenging problem. This study presents a method to resolve issues of motion blur, poor quality of videos, occlusions, the difference in body structure or size, and high computation or memory requirement. This study contributes to the improvement of recognition of human interaction during disasters such as an earthquake and flood utilizing drone videos for rescue and emergency management. We used Support Vector Machine (SVM) to classify the high-level and stationary features obtained from Convolutional Neural Network (CNN) in key-frames from videos. We extracted conceptual features by employing CNN to recognize objects from first and last images from a video. The proposed method demonstrated the context of a scene, which is significant in determining the behaviour of human in the videos. In this method, we do not require person detection, tracking, and many instances of images. The proposed method was tested for the University of Central Florida (UCF Sports Action), Olympic Sports videos. These videos were taken from the ground platform. Besides, camera drone video was captured from Southwest Jiaotong University (SWJTU) Sports Centre and incorporated to test the developed method in this study. This study accomplished an acceptable performance with an accuracy of 90.42%, which has indicated improvement of more than 4.92% as compared to the existing methods.

This study introduces a neural network-based approach to predict dust emission, specifically PM2.5 particles, during almond harvesting in California. Using a feedforward neural network (FNN), the research predicts PM2.5 emissions by analyzing key operational parameters of an advanced almond harvester. The model is trained on extensive field data from the almond pickup system, including variables like brush speed, angular velocity, and harvester forward speed. The results demonstrate a notable predictive accuracy of the FNN model, with a Mean Squared Error (MSE) of 0.02 and a Mean Absolute Error (MAE) of 0.01, indicating a high degree of precision in forecasting PM2.5 levels. The study also finds a strong correlation between certain operational parameters and PM2.5 emissions, highlighting specific areas for optimization in harvesting techniques. By integrating machine learning with agricultural practices, this research provides a significant tool for environmental management in almond production, offering a method to reduce harmful emissions while maintaining operational efficiency. This model presents a solution for the almond industry and sets a precedent for applying predictive analytics in sustainable agriculture.

The main purpose of this article is to identify brain diseases such as Alzheimer's and Parkinson's in an intelligent way using Python software and processing the function of neurons in the neural network areas of the brain, which are classified into different components, and the data is based on the information obtained from FMRI images using algorithms artificial intelligence can intelligently diagnose the type of disease. Therefore, by using spatial clustering based on the deep learning method with noise algorithm (DBSCAN), fMRI brain image and fMRI brain surface complexity are classified, and then image preprocessing will be applied to fMRI images by using artificial intelligence neural networks (ANN) algorithm. became. Then, by using the ANN algorithm and Deep CNN topology of the brain neural network, the type of disease in the brain can be diagnosed by simulating the performance of an artificial neural network (ANN) in Python software. Deep machine learning-based methods, especially algorithms based on neural networks, have shown great success in medical image analysis for various tasks including brain tumor detection, segmentation, and classification, and Alzheimer's and epilepsy. In this research, we propose an integrated model based on a convolutional neural network for simultaneous recognition and classification of brain diseases for intelligent diagnosis of tumors and epilepsy. The average accuracy obtained from our proposed model is 97.89 percent accuracy and 91.66 percent specificity.

Geospatial Information Systems (GIS) can provide a great environment for using machine learning algorithm for spatial data such as satellite images. Integrating this functionality with artificial intelligence algorithms for analyzing spatial data enables us to predict challenging disasters such as deforestation. Deforestation as an environmental problems has been recorded the most serious threat to environmental diversity and one of the main components of land-use change. In this paper, we investigate spatial distribution of deforestation using artificial neural networks and satellite imagery. We modeled deforestation process using various factors in determining the relationship between deforestation and environmental and socioeconomic factors. Hence, for this purpose, the proximity to roads and habitats, fragmentation of the forest, height from sea level, slope, and soil type are considered in the model. In this research, we modeled land cover changes (forests) to predict deforestation using an artificial neural network due to its significant potential for the development of nonlinear complex models. The procedure involves image registration and error correction, image classification, preparing deforestation maps, determining layers, and designing a multi-layer neural network to predict deforestation. The satellite images for this study are of a region in Hong Kong which are captured from 2012 to 2016. The results of the study demonstrate that neural networks approach for predicting deforestation can be utilized and its outcomes show the areas that destroyed during the research period.

In urban Vehicular Ad Hoc Network (VANET) environments, buildings play a crucial role as they can act as obstacles that attenuate the transmission signal between vehicles. Quantifying the impact of buildings on the transmission quality is essential, especially in critical scenarios involving emergency vehicles, where reliable communication is of utmost importance. In this research, we propose a supervised learning approach based on artificial neural networks (ANNs) to develop a predictive model capable of estimating the level of signal degradation, represented by the bit error rate (BER), based on the obstacles perceived by moving emergency vehicles. By establishing a relationship between the level of signal degradation and the encountered obstacles, our proposed mechanism enables efficient routing decisions to be made prior to the transmission process. Consequently, data packets are routed through paths that exhibit the lowest BER. To gather the necessary training data, we employed SUMO and NS-3 simulations. The simulation results demonstrate that our developed model successfully learns and accurately estimates the BER for new data instances. Overall, our research contributes to enhancing the performance and reliability of communication in urban VANET environments, especially in critical scenarios involving emergency vehicles, by leveraging supervised learning and artificial neural networks to predict signal degradation levels and optimize routing decisions accordingly.

Human action recognition (HAR) based on skeleton data is a challenging yet important technique because of its wide range of applications in many fields, including patient monitoring, security surveillance, and observing human-machine interactions. Many algorithms that attempt to distinguish between many types of activities have been proposed. However, most practical applications require highly accurate detection of specific types of activities. In this study, a novel and highly accurate spatiotemporal graph autoencoder network for HAR based on skeleton data is proposed. Furthermore, an extensive study was conducted using different modalities. For this purpose, a spatiotemporal graph autoencoder that automatically learns spatial as well as temporal patterns from human skeleton datasets was built. The powerful graph convolutional network named GA-GCN, developed in this study, notably outperforms most of the existing state-of-the-art methods based on two common datasets, namely NTU RGB+D and NTU RGB+D 120 . On the first dataset, we achieved an accuracy of 92.3% and 96.7% based on the cross-subject and cross-view evaluations, respectively. On the other more challenging dataset (i.e. NTU RGB+D 120), GA-GCN achieved 88.8% and 90.4% based on the cross-subject and cross-set evaluation, respectively.

In recent years, Neural networks are increasingly deployed in various fields to learn complex patterns and make accurate predictions. However, designing an effective neural network model is a challenging task that requires careful consideration of various factors, including architecture, optimization method, and regularization technique. This paper aims to comprehensively overview the state-of-the-art artificial neural network (ANN) generation and highlight key challenges and opportunities in machine learning applications. It provides a critical analysis of current neural network model design methodologies, focusing on the strengths and weaknesses of different approaches. Also, it explores the use of different learning approaches, including convolutional neural networks (CNN), deep neural networks (DNN), and recurrent neural networks (RNN) in image recognition, natural language processing, and time series analysis. Besides, it discusses the benefits of choosing the ideal values for the different components of ANN, such as the number of Input/output layers, hidden layers number, activation function type, epochs number, and model type selection, which help improve the model performance and generalization. Furthermore, it identifies some common pitfalls and limitations of existing design methodologies, such as overfitting, lack of interpretability, and computational complexity. Finally, it proposes some directions for future research, such as developing more efficient and interpretable neural network architectures, improving the scalability of training algorithms, and exploring the potential of new paradigms, such as Spiking Neural Networks, quantum neural networks, and neuromorphic computing.

In this work we present the results obtained with an artificial neural network (ANN) which we trained to predict the expected output of high-order harmonic generation (HHG) process, while exploring a multi-dimensional parameter space. We argue on the utility and efficiency of the ANN model and demonstrate its ability to predict the outcome of HHG simulations. In this case study we present the results for a loose focusing HHG beamline, where the changing parameters are: the laser pulse energy, gas pressure, gas cell position relative to focus and gas cell length. The physical quantity which we predict here using ANN is directly related to the total harmonic yield in a specified spectral domain (20-40 eV). We discuss the versatility and adaptability of the presented method.

Estimating plume cloud height is essential for various applications, such as global climate models. Smokestack plume rise is the constant height at which the plume cloud is carried downwind as its momentum dissipates and the plume cloud and the ambient temperatures equalize. Although different parameterizations are used in most air-quality models to predict the plume rise, they have been unable to estimate it properly. This paper proposes a novel framework to monitor smokestack plume clouds and make long-term, real-time measurements of the plume rise. For this purpose, a three-stage framework is developed based on Deep Convolutional Neural Networks (DCNNs). In the first stage, an improved Mask R-CNN, called Deep Plume Rise Network (DPRNet), is applied to recognize the plume cloud. Then, image processing analysis and least squares theory are respectively used to detect the plume cloud’s boundaries and fit an asymptotic model into their centerlines. The y-component coordinate of this model’s critical point is considered the plume rise. In the last stage, a geometric transformation phase converts image measurements into real-life ones. A wide range of images with different atmospheric conditions, including day, night, and cloudy/foggy, have been selected for the DPRNet training algorithm. Obtained results show that the proposed method outperforms widely-used networks in smoke border detection and recognition.

Dynamic neural networks (DNN) are types of artificial neural networks (ANN) that are designed to work with sequential data where context in time is important. In contrast to traditional static neural networks that process data in a fixed order, dynamic neural networks use information about past inputs, which is important if dynamic of a certain process is emphasized. They are widely used in natural language processing, speech recognition and time series prediction. In industrial processes, their use is interesting for the prediction of difficult-to-measure process variables. In an industrial process of isomerization, it is crucial to measure the quality attributes affecting the octane number of gasoline. Process analyzers that are commonly used for this purpose are expensive and subject to failures, therefore, in order to achieve continuous production in case of malfunction, mathematical models for estimating the product quality attributes are imposed as a solution. In this paper, mathematical models were developed using dynamic recurrent neural networks (RNN), i.e., their subtype of a long short-term memory (LSTM) architecture. The results of the developed models were compared with the results of several types of other data-driven models developed for an isomerization process, such as multilayer perceptron (MLP) artificial neural networks, support vector machines (SVM) and dynamic polynomial models. The obtained results are satisfactory, which suggests a good possibility of application.

Robot manipulators are robotic systems that are frequently used in automation systems and able to provide increased speed, precision and efficiency in the industrial applications. Due to their nonlinear and complex nature, it is crucial to optimize the robot manipulator systems in terms of trajectory control. In this study, positioning analysis based on artificial neural networks (ANN) were performed for robot manipulator systems used in the textile industry and the optimal ANN model for the high-accuracy positioning was improved. The inverse kinematic analysis of a 6 degree of freedom (DOF) industrial denim robot manipulator were carried out via 4 different learning algorithms of Delta-Bar-Delta (DBD), Online Back Propagation (OBP), Quick Back Propagation (QBP) and Random Back Propagation (RBP) for proposed neural network predictor. From the results obtained, it was observed that QBP based 3-10-6 type ANN structure produced the optimal results in terms of estimation and modelling of trajectory control. In addition, 3-5-6 type ANN structure was also improved and its Root Mean Square Error (RMSE) and statistical R2 performances were compared to that of 3-10-6 ANN structure. Consequently, it can be concluded that the proposed neural predictors can successfully be employed in real-time industrial applications for robot manipulator trajectory analysis.

Diarrhoea is a serious cause of mortality worldwide that can lead to dehydration, gut barrier function impairment, nutrient malabsorption, and alterations of the gut microbiota (dysbiosis). Current solutions for its management, such as oral rehydration salts (ORS), inhibitors of the gut motility, antibiotics, and living probiotics only partially counteract the mechanisms of the disease and do not provide a full coverage of the problem. Potential risks of the use of living probiotic strains, particularly in immunocompromised patients, can be eliminated with the use of tyndallized (heat-killed) postbiotic bacteria and yeast. ABB C22® is a postbiotic combination of three tyndallized yeasts, namely Saccharomyces boulardii, Saccharomyces cerevisiae, and Kluyveromyces marxianus. To assess the action of the postbiotic combination on diarrhoea, immune and gut epithelial cell signaling assays, gut barrier formation assay and rotavirus gene expression assay were performed. ABB C22® showed a strong anti-inflammatory effect, an induction of the build-up of the gut epithelium, and a degree of protection against rotavirus infection. These experimental studies support the use of the postbiotic ABB C22® as a solution for the management of diarrhoea and gastrointestinal conditions, alone or in combination with existing but incomplete treatments.

Identification of plants is a challenging task which aims to identify the family, genus, and species level according to morphological features. Automated deep learning-based computer vision algorithms are widely used for identifying plants and can help users to narrow down the possibilities. However, numerous morphological similarities between and within species make the classification difficult. In this paper, we tested a custom convolution neural network (CNN) and vision transformer (ViT) based models using the PyTorch framework to classify plants. We used a large dataset of 88K and 16K images for classifying plants at genus and species levels respectively. Our results show that for classifying plants at the genus level, ViT models perform better compared to CNN-based models ResNet50 and ResNet-RS-420, and other state-of-the-art CNN-based models suggested in previous studies on a similar dataset. The ViT model achieved top accuracy of 83.3% for classifying plants at the genus level. ViT models also perform better for classifying plants at the species level compared to CNN-based models ResNet50 and ResNet-RS-420, with a top accuracy of 92.5%. We show that the correct set of augmentation techniques plays an important role in classification success.

Diarrhoea is a serious cause of mortality worldwide that can lead to dehydration, gut barrier function impairment, nutrient malabsorption, and alterations of the gut microbiota (dysbiosis). Current solutions for its management, such as oral rehydration salts (ORS), inhibitors of the gut motility, antibiotics, and living probiotics only partially counteract the mechanisms of the disease and do not provide a full coverage of the problem. Potential risks of the use of living probiotic strains, particularly in immunocompromised patients, can be eliminated with the use of tyndallized (heat-killed) postbiotic bacteria and yeast. ABB C22® is a postbiotic combination of three tyndallized yeasts, namely Saccharomyces boulardii, Saccharomyces cerevisiae, and Kluyveromyces marxianus. To assess the action of the postbiotic combination on diarrhoea, immune and gut epithelial cell signaling assays, gut barrier formation assay and rotavirus gene expression assay were performed. ABB C22® showed a strong anti-inflammatory effect, an induction of the build-up of the gut epithelium, and a degree of protection against rotavirus infection. These experimental studies support the use of the postbiotic ABB C22® as a solution for the management of diarrhoea and gastrointestinal conditions, alone or in combination with existing but incomplete treatments.

Over the years, various models have been developed in the stages of the mining process that have allowed predicting and enhancing results, but it is the breakage the variable that connects all the activities of the mining process from the point of view of costs (drilling, blasting, loading, hauling, crushing and grinding). To improve this process, we come up with an idea to develop a breakage prediction model; on the basis of the main variables involved in the drilling and blasting process. For this purpose, we design a computer model based on an Artificial Neuronal Networks (ANN), built by using the most representative variables that come into play with drilling and blasting, such as: the properties of the explosives, the geomechanical parameters of the rock mass, and the design parameters of drilling-blasting. For its experimentation and validation, we have taken the data from a copper mine as reference located in the north of Chile, because of we have the dataset of that ore deposit, which is valid and reliable to evaluate prediction problems based on ANN applied to copper mines. The ANN architecture was of the supervised type, feedforward, with 3 layers and 13 neurons in the only hidden layer, trained with the input data using a dataset with the previously mentioned variables, which then were compared with the breakage results. The model was feed backed in its learning process until it becomes perfected, and is a prediction option that can be used in future blasting of ore deposits with similar characteristics using the same representative variables. Therefore, this is a valid alternative for predicting rock breakage, given that it has been experimentally validated, and has achieved moderately reliable results, providing higher correlation coefficients than traditional models, and with the additional advantage that an ANN model provides, due to its ability to learn and recognize compiled dataset patterns. In this way, using this computer model we can obtain satisfactory results that allow us to predict breakage, providing an alternative for evaluating the costs that this entails.

Predicting human trajectories poses a significant challenge due to the complex interplay of pedestrian behavior, which is influenced by environmental layout and interpersonal dynamics. This complexity is further compounded by variations in scene density. To address this, we introduce a novel dataset from the Festival of Lights in Lyon 2022, characterized by a wide range of densities (0.2-2.2 ped/m2). Our analysis demonstrates that density-based classification of data can significantly enhance the accuracy of predictive algorithms. We propose an innovative two-stage processing approach, surpassing current state-of-the-art methods in performance. Additionally, we utilize a collision-based error metric to better account for collisions in trajectory predictions. Our findings indicate that the effectiveness of this error metric is density-dependent, offering prediction insights. This study not only advances our understanding of human trajectory prediction in dense environments but also presents a methodological framework for integrating density considerations into predictive modeling, thereby improving algorithmic performance and collision avoidance.

Music has the innate potential to reach all parts of the brain, stimulates certain brain areas which are not achievable through other modalities. Music Therapy (MT) is being used for more than a century to treat individuals who needs personalized care. MT optimizes motor, speech and language responsibilities of the brain and improves cognitive performance. Pervasive developmentdisorder (PDD) is a multifaceted, neuro developmental disorder and autism spectrum disorder (ASD) comes under PDD, which is defined by deficiencies in three principal spheres: social connection with others, communicative and normal movement skills. The conventional imaging studies illustrate reduced brain area connectivity in people with ASD, involving selected parts of the brain cortex. People with ASD express much interest in musical activities which engages the brain network areas and improves communication and social skills.The main objective of this review is to analyze the potential role of MT in treating the neurological conditions, particularly ASD. Evidence based studies have reported the extensive therapeutic application of music on various part of the brain in a nonverbal child with autism through hearing or making music.Hence we hypothesized that MT intervention can improve the communication capacity in people with ASD, than customary neurorestoration therapy alone.

The Covid-19 pandemic was a challenge for the whole world and it had major secondary effects on humans and environmental health. The viral infection induced, in many situations, secondary bacterial infections, especially enteric infections by destabilizing the balance of the gastrointestinal microbiota. The large-scale use of antibiotics and biocides both for curative and preventive purposes has determined an increase in bacterial resistance and at the same time the possibility of pathogenic microorganisms’ multiplication and their dissemination to natural environments. Wastewater is the main vector of faecal microorganisms that favour their dissemination into natural aquatic ecosystems. The present paper aimed to analyze the effect of Covid-19 pandemic on the microbiological quality of wastewater from sewage treatment plants in Romania and its impact on receiving rivers. In order to highlight different and important areas of Romania, 3 cities from the east, center and west were selected for a microbiological evaluation of their WWTPs influent and effluent between ante-Covid-19 and Covid-19 pandemic peak period, when the Covid-19 pandemic had a direct impact on WWTPs microbial composition. Our study showed a higher contamination with fecal bacteria linked to a higher Covid-19 incidence. The increased usage of pharmaceutical compounds, at their turn, increased the number of resistant bacteria reaching the environment via WWTP effluents.

The supply chain has incorporated products by putting them into hair scarfs. This study introduces the use of mini chips in health and beauty products and can reduce fatigue through enhanced sleep patterns. The mini chip could be placed in the scarf and used as a prototype. RFID technology provides the supply chain with specific information that is used to identify products and make communication easier. (Muhammad, et. al. 2013) This paper presents a new tool herein referred to as a scarf prototype which is developed to analyse EMG (electromyogram), ECG (electrocardiography), EEG (electroencephalogram), and EOG (electro-oculogram) signals that focuses in the area of sleep disorders. The mini chips used can be used to determine a solution for sleep disruption by using automated analytics. This could lead to improvement in our understanding of sleep disruption and overall sleep physiology. Automated technology allows repeated measurements, evaluation of sleep patterns, and provide suggestions to improve a person’s quality of sleep. This analysis compares the use of polysomnography and the scarf prototype. The analytics provide models and shows correlation between variables, such as EMG, ECG, EEG, and EOG. This study shows that the results from the scarf prototype is just as reliable as the original method, polysomnography.

To protect power lines, distance relays are used which can rely on a modified distance resistance. But usually the operating range of these relays changes as the network conditions change (network topology, load value, output value, etc.) and leads to false trips, By using methods that can process information and recognize patterns, for example, the use of micro and intelligent processor algorithms can use the new relays with high precision and thus provide adequate protection. In this study, a distance relay was modeled using a neural network, and it was observed that the neural relay had higher accuracy than the conventional relay. In addition to detecting the fault and its location, type and phase of the fault, three-stage simultaneous protection can be performed. As a result, the number of linear relays can be reduced by using relays based on neural technologies. An MLP (multilayer perceptron) neural network is used to model a sequence of distances.

The diagnosis of papillary thyroid carcinoma has always been a concerned and challenging issue and it is very important and meaningful to have a definite diagnosis before the operation. In this study, we tried to use an artificial intelligence algorithm instead of medical statistics to analyze the genetic fingerprint from gene chip results to identify papillary thyroid carcinoma. We trained 20 artificial neural network models with differential genes and other important genes related to the cell metabolic cycle as the list of input features, and apply them to the diagnosis of papillary thyroid cancer in the independent validation data set. The results showed that when we used the DEGs and all genes lists as input features the models got the best diagnostic performance with AUC=98.97% and 99.37% and the accuracy were both 96%. This study revealed that the proposed artificial neural network models constructed with genetic fingerprints could achieve a prediction of papillary thyroid carcinoma. Such models can support clinicians to make more accurate clinical diagnoses. At the same time, it provides a novel idea for the application of artificial intelligence in clinical medicine.

In recent years, artificial neural networks (ANNs) have won numerous contests in pattern recognition, machine learning, and artificial intelligence. The basic unit of an ANN is to mimic neurons in the brain. Neuron in ANNs is expressed as f (wx+b) or f (wx). This structure does not consider the information processing capabilities of dendrites. However, recently, studies shown that dendrites participate in pre-calculation in the brain. Concretely, biological dendrites play a role in the pre-processing to the interaction information of input data. Therefore, it is time to perfect the neuron of the neural network. This paper, add dendrite processing section, presents a novel artificial neuron, according to our previous studies (CR-PNN or Gang transform). The dendrite processing section can be expressed as . Because I perfected the basic unit of ANNs— neuron, there are so many networks to try. This article gives the basic architecture for reference in future research.

Deep learning models are part of the family of artificial neural networks and, as such, it suffers of catastrophic interference when they learn sequentially. In addition, most of these models have a rigid architecture which prevents the incremental learning of new classes. To overcome these drawbacks, in this article we propose the Self-Improving Generative Artificial Neural Network (SIGANN), a type of end-to-end Deep Neural Network system which is able to ease the catastrophic forgetting problem when leaning new classes. In this method, we introduce a novelty detection model to automatically detect samples of new classes, moreover an adversarial auto-encoder is used to produce samples of previous classes. This system consists of three main modules: a classifier module implemented using a Deep Convolutional Neural Network, a generator module based on an adversarial autoencoder; and a novelty detection module, implemented using an OpenMax activation function. Using the EMNIST data set, the model was trained incrementally, starting with a small set of classes. The results of the simulation show that SIGANN is able to retain previous knowledge with a gradual forgetfulness for each learning sequence. Moreover, SIGANN can detect new classes that are hidden in the data and, therefore, proceed with incremental class learning.

In the present study, a hybrid optimizing algorithm has been proposed using Genetic Algorithm (GA)and Particle Swarm Optimization (PSO) for Artificial Neural Network (ANN) to improve the estimation of electricity demand of the state of Tamil Nadu in India. The GA-PSO model optimizes the coefficients of factors of gross state domestic product (GSDP) , electricity consumption per capita, income growth rate and consumer price index (CPI) that affect the electricity demand. Based on historical data of 25 years from 1991 till 2015 , the simulation results of GA-PSO models are having greater accuracy and reliability than single optimization methods based on either PSO or GA. The forecasting results of ANN-GA-PSO are better than models based on single optimization such as ANN-BP, ANN-GA, ANN-PSO models. Further the paper also forecasts the electricity demand of Tamil Nadu based on two scenarios. First scenario is the "as-it-is" scenario , the second scenario is based on milestones set for achieving goals of "Vision 2023" document for the state. The present research also explores the causality between the economic growth and electricity demand in case of Tamil Nadu. The research indicates that a direct causality exists between GSDP and the electricity demand of the state.

In the present study, a hybrid optimizing algorithm has been proposed using Genetic Algorithm (GA)and Particle Swarm Optimization (PSO) for Artificial Neural Network (ANN) to improve the estimation of electricity demand of the state of Tamil Nadu in India. The GA-PSO model optimizes the coefficients of factors of gross state domestic product (GSDP) , electricity consumption per capita, income growth rate and consumer price index (CPI) that affect the electricity demand. Based on historical data of 25 years from 1991 till 2015, the simulation results of GA-PSO models are having greater accuracy and reliability than single optimization methods based on either PSO or GA. The forecasting results of ANN-GA-PSO are better than models based on single optimization such as ANN-BP, ANN-GA, ANN-PSO models. Further the paper also forecasts the electricity demand of Tamil Nadu based on two scenarios. First scenario is the “as-it-is” scenario, the second scenario is based on milestones set for achieving goals of “Vision 2023” document for the state. The present research also explores the causality between the economic growth and electricity demand in case of Tamil Nadu. The research indicates that a direct causality exists between GSDP and the electricity demand of the state.

The study aims to analyze the characteristic parameters of rooftop photovoltaic (PV) power generation on industrial plant buildings in the Ningxia region of China, in order to evaluate the impact of passive design characteristic parameters on the benefits of PV power generation and determine the degree of impact of different passive design characteristic parameters. The methodology involves analyzing the characteristics of existing industrial plant buildings in Ningxia, China, and conducting a series of regional studies on the parameters of plant PV power generation influencing factors. The simulation results revealed that five features, including roof form, PV panel laying pattern, PV panel laying area, azimuth angle, and PV module material, have a significant impact on PV power generation benefits of industrial plant buildings.The study further uses MATLAB 2022b to build a backpropagation neural network model with 5 neurons in the implicit layer to predict the PV power generation benefits. The model calculates the whole-life cycle power generation benefits and the whole-life cycle reduction of carbon emissions as output data. Finally, the Mean Impact Value (MIV) method is employed to select the feature parameter values one by one within their range, and the passive design feature parameters that have the greatest influence on the prediction results are identified as the PV panel laying method, the PV panel tilt angle, and the PV material parameters, respectively.

As Li-ion batteries use is spreading, incidents in large energy storage systems (stationary storage containers, …) or in large-scale cell and battery storages (warehouse, recyclers, …), often leading to fire, are occurring on regular basis. Water remains one of the most efficient fire extinguishing agents for tackling those battery incidents and large quantities are usually necessary. Since bat-teries contains various potentially harmful components (metals and their oxides or salts, sol-vents…) and that thermal runway induced battery incidents are accompanied with complex and potentially multistage fume emissions (containing both gas and particles) the potential impact of fire run-off water on the environment should be considered and assessed carefully. The tests presented in this paper focus on the analysis of the composition of run-off waters used to spray NMC Li-ion modules under thermal runaway. It highlights that waters used for fire-fighting are susceptible to contain many metals, including Ni, Mn, Co, Li and Al mixed with other carbonaceous species (soot, tarballs) and sometimes undecomposed solvents used in the elec-trolyte. Extra-polation of pollutant concentrations compared with PNEC values showed that, for large scale incidents, run-off water could be potentially hazardous to the environment.

The fatigue life of concrete is affected by many interwoven factors whose effect is nonlinear. Be-cause of its unique self-learning ability and strong generalization capability, the Bayesian regu-larized backpropagation neural network (BR-BPNN) is proposed to predict concrete behavior in tensile fatigue. The optimal model was determined through various combinations of network parameters. The average relative impact value (ARIV) was constructed to evaluate the correla-tion between fatigue life and its influencing parameters (maximum stress level Smax, stress ratio R, static strength f, failure probability P). ARIV results were also compared with other factor as-sessment methods (weight equation and multiple linear regression analyses). Using BR-BPNN, S-N curves were then obtained for the combinations of R=0.1, 0.2, 0.5; f=5, 6, 7MPa; P=5%, 50%, 95%. The tensile fatigue results under different testing conditions were finally compared for compatibility. It was concluded that Smax has the most significant negative effect on fatigue life; the degree of influence of R, P, and f, which positively correlate with fatigue life, decreases suc-cessively. ARIV is confirmed as a feasible way to analyze the importance of parameters and could be recommended for future applications. The tensile fatigue performance of plain concrete under different stress states (flexural tension, axial tension, splitting tension) does not differ sig-nificantly. Besides utilizing the valuable fatigue test data scattered in the literature, insights gained from this work could provide a reference for subsequent fatigue test program design and fatigue evaluation.

We propose a neural-network-based watermarking method that introduces the quantized activation function that approximates the quantization of JPEG compression. Many neural-network-based watermarking methods have been proposed. Conventional methods have acquired robustness against various attacks by introducing an attack simulation layer between the embedding network and the extraction network. The quantization process of JPEG compression was replaced by the noise addition process in the attack layer of the conventional methods. In this paper, we propose a quantized activation function that can simulate the JPEG quantization standard as it is in order to improve the robustness against the JPEG compression. Our quantized activation function consists of several hyperbolic tangent functions and is applied as an activation function for neural networks. Our network was introduced in the attack layer of ReDMark proposed by Ahmadi et al. to compare it with their method. That is, the embedding and extraction networks had the same structure. We compared the usual JPEG compressed images and the images applying the quantized activation function. The results showed that a network with quantized activation functions can approximate JPEG compression with high accuracy. We also compared the bit error rate (BER) of estimated watermarks generated by our network with those generated by ReDMark. We found that our network was able to produce estimated watermarks with lower BERs than those of ReDMark. Therefore, our network outperformed the conventional method with respect to image quality and BER.

ABSTRACT Purpose: Tongue image analysis for disease diagnosis is an ancient traditional non-invasive diagnosis technique widely used by traditional medicine practitioners. Deep Learning based multi-label disease detection models offer tremendous potential to clinical decision support systems, by facilitating preliminary diagnosis. Methods: In this work, we propose a multi-label disease detection pipeline, where in observation and analysis of tongue images captured and received via smartphones assist in predicting the health status of an individual. All images are voluntarily given by subjects consulting collaborating physicians. Images thus acquired are first and foremost classified either into a diseased or a normal category by a 5-fold cross-validation algorithm using a convolution neural network (MobileNetV2) model for binary classification. Once the diseased label is predicted, the image is used to diagnose multiple diseases using the prediction algorithm based on DenseNet121. Results: Average accuracy of 93 % was achieved in classifying diseased from normal healthy tongue by detection model with MobileNetV2 architecture. Multilabel disease classification produced more than 90% accurate results for the seven class labels considered. Conclusion: AI based image analysis shows promising results and an extensive dataset could provide further improvements to this approach. Rather than employing high-cost sophisticated image capturing setup, experimenting with smartphone images opens opportunity to provide preliminary health status to individuals on smartphone prior to further line of treatment and diagnosis.

Immunotherapy, particularly Immune Checkpoint Blockade (ICB), has demonstrated significant efficacy in treating melanoma in recent years. However, accurately predicting treatment success and avoiding ineffective therapies remains an unresolved challenge. Therefore, this study aims to develop statistical models utilizing neural networks to forecast the effectiveness of immune checkpoint therapies for melanoma patients. Our models primarily rely on Artificial Neural Networks (ANN) to anticipate both Overall Survival (OS) and Progression-Free Survival (PFS) among melanoma patients undergoing anti-CTLA4 and anti-PD1/anti-PDL1 therapy. We incorporate gene expression data, measured in Transcripts per Million (TPM), derived from bulk tumor RNA-sequencing datasets. Additionally, clinical variables such as gender, age, and treatment type are factored into our analysis. The ANN underwent optimization to attain the highest feasible precision in anticipating the predetermined survival outcome. Issues stemming from high-dimensional data, such as overfitting, were tackled through regularization and feature selection methods. Consequently, the ANN-based model incorporating feature selection exhibited the capacity to forecast survival (PFS) in response to ICB therapy with a maximal precision of 86%. Conversely, the ANN lacking feature selection but incorporating regularization achieved accuracies of up to 72% for PFS and 71% for OS, correspondingly. In order to confront the challenge posed by limited patient samples and to assess replicability, the model underwent training and validation based on the amalgamation of all five datasets. However, this amalgamation failed to enhance predictive performance, necessitating further investigations.

Transcription factors (TFs) are crucial in modulating gene expression and sculpting cellular and organismal phenotypes. The identification of TF-target gene interactions is pivotal for comprehending molecular pathways and disease etiologies but has been hindered by the demanding nature of traditional experimental approaches. This paper introduces a novel web application, utilizing the R programming language, which predicts TF-target gene relationships and vice versa. Our application integrates the predictive power of various bioinformatic tools, leveraging their combined strengths to provide robust predictions. It merges databases for enhanced precision, incorporates gene expression correlation for accuracy, and employs pan-tissue correlation analysis for context-specific insights. The application also enables the integration of user data with established resources to analyze TF-target gene networks. Despite its current limitation to human data, it provides a platform for exploring gene regulatory mechanisms comprehensively. This integrated, systematic approach offers researchers an invaluable tool for dissecting the complexities of gene regulation, with the potential for future expansions to include a broader range of species.

Aimed for the difficulty and complexity of detecting the piston error for segmented telescope, this paper proposed a new piston error measurement method based on a hybrid artificial neural net-work. Firstly, we use Resnet network to learn the mapping relationship between the focal plane degradation image and the signs of the piston error. Then, based on the established theoretical re-lationship between modulation transfer function and the piston error, BP neural network is used here to learn the mapping relationship between the MTF and the absolute value of the piston error. After the training of the hybrid network is completed, a wide-range and high-precision detection of the piston error of the sub-mirrors can be achieved using the combined output of the two net-works only a focal plane image of a point source with broadband illumination is used as input. The detection range can reach the whole coherent length of the input broadband light, and the detec-tion accuracy can reach 10nm. The method proposed in this paper has the advantages of high de-tection accuracy, wide detection range, low hardware cost, small network scale and low training difficult.

Nowadays the dynamism induced by the constant change of strategic decisions on the markets produces an extra difficulty in the management of an organization. The strategic decisions made by managers can become obsolete in a short period of time. One of the major difficulties in managing a commercial organization is to predict, with some precision degree, the impact some strategic decisions have on the financial results. Business Intelligence (BI) is an area widely used to help managers to make strategic decisions. But the methods used, behind the scenes, to achieve the conclusions are kept secret by BI company-based services. Modelling the environment can be a good option to study the impact of an action, provided by a strategic decision, in a real environment. A good model should give an approximate result of an action applied to a previous state of the environment. Artificial Neural Networks (ANNs) are proven to be excellent in modeling environments with some level of data noise. The same strategic action can have different results in different organizations. A tool that allows an evaluation of a strategic action applied to an environment should have a major importance in the management scope. Modeling the environment should save time and money for the organization to improve the performance of the strategic plan. If one evaluates the state of the environment after a strategic action being applied, it can be possible to mitigate the risk of failure of the strategic plan. As we will be able to verify, it is possible to use ANNs to model strategic environments that should allow the prediction of sales and operating results by the used strategies with some precision, although the level of success will be directly related with the user’s necessity.

Human and Computer interaction has been a part of our day-to-day life. Speech is one of the essential and comfortable ways of interacting through devices as well as a human being. The device, particularly smartphones have multiple sensors in camera and microphone, etc. speech recognition is the process of converting the acoustic signal to a smartphone as a set of words. The efficient performance of the speech recognition system highly enhances the interaction between humans and machines by making the latter more receptive to user needs. The recognized words can be applied for many applications such as Commands & Control, Data entry, and Document preparation. This research paper highlights speech recognition through ANN (Artificial Neural Network). Also, a hybrid model is proposed for audio-visual speech recognition of the Tamil and Malay language through SOM (Self-organizing map0 and MLP (Multilayer Perceptron). The Effectiveness of the different models of NN (Neural Network) utilized in speech recognition will be examined.

Symmetry in biological and physical systems is a product of self-organization driven by evolutionary processes, or mechanical systems under constraints. Symmetry-based feature extraction or representation by neural networks may unravel the most informative contents in large image databases. Despite significant achievements of artificial intelligence in recognition and classification of regular patterns, the problem of uncertainty remains a major challenge in ambiguous data. In this study, we present an artificial neural network that detects symmetry uncertainty states in human observers. To this end, we exploit a neural network metric in the output of a biologically inspired Self-Organizing Map, the Quantization Error (SOM-QE). Shape pairs with perfect geometric mirror symmetry but a non-homogenous appearance, caused by local variations in hue, saturation, or lightness within and/or across the shapes in a given pair produce, as shown here, longer choice RT for ‘yes’ responses relative to symmetry. These data are consistently mirrored by the variations in the SOM-QE from unsupervised neural network analysis of the same stimulus images. The neural network metric is thus capable of detecting and scaling human symmetry uncertainty in response to patterns. Such capacity is tightly linked to the metric’s proven selectivity to local contrast and color variations in large and highly complex image data.

All types of sports are potential application scenarios for automatic and real-time visual object and event detection. In rink hockey, the popular roller quad skate variant of hockey team sports, it is of great interest to automatically track player’s movements and positions, player’s sticks and, also, making other judgments, such as being able to locate the ball. In this work, we introduce a real-time pipeline composed by an object detection model, created specifically for rink hockey games, followed by a knowledge-based event detection module. Even in the presence of occlusions and quick motions, our deep learning object detection model effectively identifies and tracks, in real-time, important visual elements such as: ball; players; sticks; referees; crowd; goalkeeper; and goal. Using a curated dataset composed by a collection of videos of rink hockey, comprising 2525 annotated frames, we trained and evaluated the algorithm performance and compare it to state of the art object detection techniques. Our object detection model, based on YOLOv7, presents a global accuracy of 80%, and presents a good performance in terms of accuracy and speed, according to our results, making it a good choice for rink hockey applications. In our initial tests, the event detection module successfully detected one important event type in rink hockey games, the occurrence of penalties.

Electricity price forecasting has become a crucial element for both private and public decision-making. This importance has been growing since the wave of deregulation and liberalization of energy sector worldwide late 1990s. Given these facts, this paper tries to come up with a precise and flexible forecasting model for the wholesale electricity price for the Italian power market on an hourly basis. We utilize artificial intelligence models such as neural networks and bagged regression trees that are rarely used to forecast electricity prices. After model calibration, our final model is bagged regression trees with exogenous variables. The selected model outperformed neural network and bagged regression with single price used in this paper, it also outperformed other statistical and non-statistical models used in other studies. We also confirm some theoretical specifications of the model. As a policy implication, this model might be used by energy traders, transmission system operators and energy regulators for an enhanced decision-making process.

PURPOSE: Breast cancer tumors frequently have intratumor heterogeneity. Tumors with high intratumor heterogeneity have caused therapeutic resistance and have human epidermal growth factor receptor 2 (HER2) heterogeneity in response to HER2-targeted therapies. This study aimed to investigate whether high HER2 heterogeneity levels were clinically related to poor prognosis for HER2-targeted adjuvant therapies resistance in primary breast cancers. METHODS: This study included patients with primary breast cancer (n = 251) treated with adjuvant HER2-targeted therapies. HER2 heterogeneity was manifested by the shape of HER2 fluorescence in situ hybridization amplification (FISH) distributed histograms with HER2 gene copy number within a tumor sample. Those heterogeneity classified each tumor into the biphasic grade graph (high heterogeneity [HH]) group and the monophasic grade graph (low heterogeneity [LH]) group. Both groups were evaluated for disease-free survival (DFS) and overall survival (OS) for a median of ten years of annual follow-up. RESULTS: Of 251 patients with HER2-positive breast cancer, 46 (18.3%) and 205 (81.7%) were classified into the HH and LH groups, respectively. The HH group had more distant metastases and a poorer prognosis than the LH group (DFS: P < 0.001 (HH:63% vs LH:91% at 10 years), and OS: P = 0.012 (HH:78% vs LH:95% at 10 years). CONCLUSION: High HER2 heterogeneity is a poor prognostic factor in patients with HER2-positive breast cancer. A novel approach of heterogeneity, which is manifested by the shape of HER2 FISH distributions, might be clinically useful in the prognosis prediction of patients after HER2 adjuvant therapy.

Productivity has been modest in construction due to many reasons, especially project-specific operations and fragmentation. The main aim of this research is to map the challenges towards industrialization in construction through a comparative study of the manufacturing industry. An inductive approach and a qualitative method are followed by applying semi-structured inter-views, and node-based thematic analysis. The key elements of industrialization in mature man-ufacturing companies are benchmarked. The findings indicate a specific order of steps for indus-trialization in construction. Data and information management with achieved systematization have been sources of productivity in manufacturing companies. However, the systematization starts from the offering, construction companies need to define their offering, that is the products, and define their respective data. Only accurate and good quality data on products enables the systematization of order delivery processes, which are the engine for a company’s success or failure. Continuous efficiency improvement is only possible with systematized processes and respective data related to the processes. The originality involves clarifying the industrialization of construction companies via products, respective data, and processes considering industrialized manufacturing companies.

The primary barrier to understanding visual and abstract information in STEM fields is representational competence the ability to generate, transform, analyze and explain representations. The relationship is known between the foundational visual literacy and the domain specific science literacy, however how science literacy is a function of science learning is still not well understood despite investigation across many fields. To support the improvement of students’ representational competence and promote learning in science, identification of visualization skills is necessary. This project details the development of an artificial neural network (ANN) capable of measuring and modeling visual science literacy (VSL) via neurological measurements using functional near infrared spectrometry (fNIRS). The developed model has the capacity to classify levels of scientific visual literacy allowing educators and curriculum designers the ability to create more targeted and immersive classroom resources such as virtual reality, to enhance the fundamental visual tools in science.

The importance of this study may be defined by using the smart techniques to earned value indicators of residential buildings projects in Republic of Iraq, only one development intelligent forecasting model was presented to predict Schedule Performance Index (SPI), Cost Performance Index (CPI), and To Complete Cost Performance Indicator (TCPI) are defined as the dependent. The approach is principally influenced by the determining numerous factors which effect on the earned value management, that involves Iraqi historical data. In addition, six independent variables (F1: BAC, Budget at Completion., F2: AC, Actual Cost., F3, A%, Actual Percentage., F4: EV, Earned Value. F5: P%, Planning Percentage., and F6: PV, Planning Value) were arbitrarily designated and satisfactorily described for per construction project. It was found that ANN has the capability to envisage the dust storm with a great accuracy. The correlation coefficient (R) has been 90.00%, and typical accuracy percentage has been 89.00%.

Greenhouse Gases (GHGs) emission has considerable impact on global warming and climate change. Since energy systems and their features noticeably influence on the amount of GHGs emission, it can be modeled based on the specifications of energy sources utilized by the countries. In addition, economic activity is another factor which should be considered in GHG emission modeling. In this work, Artificial Neural Network (ANN) is used for estimating carbon dioxide emission, as one of the most abundant GHGs, on the basis of shares of various energy sources used as primary energy supply and GDP as an indicator for economic activities. Five countries including Iran, Kuwait, Qatar, Saudi Arabia and United Arab Emirates (UAE) are considered as case studies. Comparing between the estimated data by the achieved model and actual quantities showed acceptable precision of the ANN model for prediction of carbon dioxide emission. The average absolute relative error and the R-squared values of the GMDH model are approximately 2.28% and 0.9998, respectively. The obtained values for the mentioned statistical criteria show the precision of the model in forecasting the emission of Co2.

Multidisciplinary Design Optimization (MDO) is the most active field in the design of current complex system engineering, which is possessed with such two difficulties as subsystem information exchange and analytical and computational complexity of systems. Therefore, an improved collaborative optimization algorithm based on ANN (artificial neural network) response surface was proposed dependent on the consistency constraint algorithm and concurrent subspace algorithm. As an optimization method with secondary structure, it satisfied only local constraints in discipline layer, but provided a coordinated mechanism for interdisciplinary conflict in system layer. Finally, it was applied in the multidisciplinary design optimization of autonomous underwater vehicle (AUV). As shown from the result, the MDO convergence stability and reliability of low resistance, low noise and high maneuvering performance of the AUV shape can be ensured by the improved collaborative optimization algorithm, thus verifying the effectiveness of the algorithm.

In the conservation of monumental heritage, the collection and utilization of information are of primary importance. The Heritage Building Information Modeling (HBIM) procedure harnesses the potential of three-dimensional models, offering significant advantages in accessing documentation, interoperability, multidimensionality of intervention design, cost evaluation and maintenance management. Attention here is focused on the Certosa di Pisa, a large historical complex built in the 14th century as a monastery of the Carthusian order, currently in a state of deterioration and in need of restoration and re-functionalization. The multifaceted nature of this monumental complex, with its intricate interplay of architectural elements spanning different historical periods and featuring diverse techniques, poses a significant challenge for structural safety assessment. This case study presents an opportunity to explore an HBIM approach to streamline the diagnostic process and facilitate the intervention design phase. The goal is achieved by utilizing an accurate 3D model enriched with data from multiple sources and automating certain operations for structural assessment. The usefulness of the HBIM methodology is highlighted as a valuable tool in the realm of Cultural Heritage structures for both technicians and scholars alike.

Amid escalating urbanization, devising rational commercial space layouts is a critical challenge. Leveraging machine learning, this study uses a Back-propagation (BP) neural network to optimize commercial spaces in Weinan City's central urban area. The results indicate an increased number of commercial facilities with a trend of multi-centered agglomeration and outward expansion. Based on these findings, we propose a strategic framework for rational commercial space development emphasizing aggregation centers, development axes, and spatial guidelines. This strategy provides valuable insights for urban planners in small and medium-sized cities in the Yellow River Basin and metropolitan areas, ultimately showcasing the power of machine learning in enhancing urban planning.

Real time condition monitoring and precision health assessment system is a mandatory need for effective maintenance program in industrial sector. Rapid advancement in the information technology and other engineering technologies have invited more proactive attention from research and development in industrial sectors and particularly in condition monitoring of machines and related Industrial processes. In this work, the drill bit condition monitoring techniques have been developed based on the wavelet analysis and artificial neural network (ANN) as automatic drill bit fault detection and classification. An experimental work has been conducted to capture the vibration signals for analysis. In this experiment, the CNC drill machine is used with high carbon steel drill bit and mild steel material as work piece. The cutting condition parameters are kept constant and the wear level is changed. The Data Acquisition system (DAQ) with Lab VIEW software is used to capture the vibration signals for drill bit with different wear conditions. The captured vibrations data are analyzed using continuous wavelet transform (CWT) with Morlet wavelet and Daubechies wavelet as a prime function. In general, the CWT coefficient is used to generate the inputs features to ANN for automatic tool condition classification, with two outputs (0, 1) for healthy and (1, 0) for faulty. The results show the effectiveness of the combed WT and ANN for automatic classification of tool wear conditions with high success rate.

Accurate evaluation of health status of lithium-ion batteries must be deemed as of great significance, insofar as utility and safety of batteries are of concern. Lithium plating, in particular, is notoriously known to be a chemical reaction that can cause deterioration in, or even fatal hazards to, the health of lithium-ion batteries. Electrochemical impedance spectroscopy (EIS), which has distinct advantages such as fast or non-destructive over its competitors, suffices in detecting lithium plating and thus has been attracting increasing attention in the field of battery management, but its ability of assessing quantitatively the degree of lithium plating remains largely unexplored hitherto. On this point, this work seeks to narrow that gap, by proposing an EIS-based method that can quantify the degree of lithium plating. The core conception is to eventually circumvent the reliance on state-of-health measurement, and use instead the impedance spectrum, to acquire an estimate on battery capacity loss. To do so, the effects of solid electrolyte interphase formation and lithium plating on battery capacity must be first decoupled, so that the mass of lithium plating can be quantified. Then, based on an impedance spectrum measurement, the parameters of the fractional equivalent circuit model (ECM) of the battery can be identified. These fractional ECM parameters are received as inputs by an artificial neural network, which is tasked to establish a correspondence between the model parameters and the mass of lithium plating. The empirical part of the work revolves around the data collected from an aging experiment, and the validity of the proposed method is truthfully attested by dismantling the batteries, which is otherwise not needed during the actual uptake of the method.

This paper presents a scenario evolution model for maritime accidents using Bayesian networks (BN) to predict the most likely causes of specific types of maritime incidents. The BN nodes encompass accident type, life loss contingency, accident severity, the quarter and time period of the accident, and the type and gross tonnage of the ships involved. We analyzed 5,660 global maritime accidents from 2005 to 2020. Using Netica software, we constructed a Tree Augmented Network (TAN) model, accounting for interdependencies among risk influencing factors. We validated the results through sensitivity analysis and historical accident records. Forward causal inference and reverse diagnostic inference were then performed on each node variable to investigate the accident development trend and evolution process under predetermined conditions. The findings indicate that the model can effectively predict the likelihood of various accident scenarios under specific conditions, as well as the extrapolation of accident consequences. Forward causal reasoning reveals that general cargo ships with a gross tonnage of 1-18,500 t are most likely to experience collision, grounding, and stranding accidents in the first quarter. Reverse diagnostic reasoning indicates that during early morning hours, container ships, general cargo ships, and chemical ships with a tonnage of 1-18,500 t are less likely to involve life loss in the event of collision accidents.

Delve into the dynamic realms of neuroscience, neurology, and psychiatry with this groundbreaking editorial, unveiling the intricate mechanisms of brain function and dysfunction. Explore the latest advancements in molecular biology, genetics, epigenetics, pharmacology, and neuroimaging that are revolutionizing our understanding of neurological and psychiatric disorders. Uncover the challenges and gaps in translating cutting-edge research into practical clinical applications, aiming to enhance the lives of patients and their families. Discover the pivotal role of neuroplasticity in reshaping the brain's adaptability throughout life, alongside the promising potential of non-invasive brain stimulation techniques like transcranial magnetic stimulation and transcranial direct current stimulation. Embark on a journey of innovation and collaboration as researchers and clinicians strive to bridge the gap between bench and bedside, offering hope for improved diagnosis, prevention, and treatment of complex neurological and psychiatric conditions. Join us in this exploration of transformative ideas and novel interventions that hold the key to a brighter future for individuals and society.

Keywords: pelvic ultrasound, follicle number per ovary, FNPO, ovarian volume, PCOM, upper normal limits, referral population

The strong competition in the automotive industry has required manufacturers to implement lean production, both with methods and techniques specific to Industry 4.0. At the same time, universities must provide graduates with specific skills for applying these new production methods and techniques. In this context, a Lean Learning Factory was developed in the Pitesti University Center, which allows students to learn, experiment, and research, in an environment similar to that of enterprises, the new Lean Manufacturing methods and techniques, and Industry 4.0. The research presented in this study had as its objective identifying the minimum number of repetitions necessary to train operators who serve two differently organized workstations, one classic, the other including digital techniques, but on which the same assembly operation is performed. Several indicators were considered in the analysis, such as the number of errors, the number of stops, the effective duration of the work cycle, and the percentage ratio between the standard duration of cyclical activities and the effective duration of the work cycle. The evolution of these indicators was mathematically modelled by regression functions, using the least squares method. The obtained results also highlight the usefulness of applying the DOJO method as a Lean manufacturing-specific learning technique and the efficiency of implementing digital techniques in work organization.

In recent years, advancements in brain science and neuroscience have significantly influenced the field of computer science, particularly in the domain of reinforcement learning (RL). Drawing insights from neurobiology and neuropsychology, researchers have leveraged these findings to develop novel mechanisms for understanding intelligent decision-making processes in the brain. Concurrently, the emergence of quantum computing has opened new frontiers in artificial intelligence, leading to the development of quantum machine learning (QML). This study introduces a novel model that integrates Quantum Spiking Neural Networks (QSNN) and Quantum Long Short-Term Memory (QLSTM) architectures, inspired by the complex workings of the human brain. Specifically designed for reinforcement learning tasks in energy-efficient environments, our approach progresses through two distinct stages mirroring sensory and memory systems. In the initial stage, analogous to the brain’s hypothalamus, low-level information is extracted to emulate sensory data processing patterns. Subsequently, resembling the hippocampus, this information is processed at a higher level, capturing and memorizing correlated patterns. We conduct a comparative analysis of our model against existing quantum models such as Quantum Neural Networks and their classical counterparts, elucidating its unique contributions. Through empirical results, we aim to underscore the effectiveness of our approach in optimizing energy consumption in practical scenarios.

Data-driven models based on artificial intelligence are efficiently used to solve complex problems. The quality of groundwater is of utmost importance, as it directly impacts human health and the environment. In major parts of the world groundwater is the main source of drinking water, it is essential to periodically monitor water quality. Conventional water quality monitoring techniques involve periodical collection of water samples and analysis in the laboratory. This process is expensive, time consuming and involves lot of manual labor. The aim of our study is to build an ant colony optimized neural network for predicting groundwater quality parameters. We have proposed artificial neural network comprising of six hidden layers. The approach was validated using our groundwater quality dataset of a hard rock region in the northern part of Karnataka, India. Groundwater samples were collected by us periodically from March 2014 to October 2020 from 50 wells in this region. These samples where analysed for measuring the pH, Electrical Conductivity, Na+, Ca+, Na+, K+, Mg2+, F-, Cl- and U+. The temporal dataset was split for training, testing and validation of our model. Metrics such as R2 (Coefficient of Determination), RMSE (Root Mean Squared Error), NSE (Nash–Sutcliffe efficiencies) and MAE (Mean Absolute Error) were used to evaluate the prediction error and model performance. These performance evaluation metrics indicated the efficiency of our model in predicting the temporal variation in groundwater quality parameters. The method proposed by us can be used for prediction and the temporal frequency of sample collection can be reduced to save time and cost. The results also confirm that the combination of artificial neural network with ACO is a promising tool to optimize weights while training the network, and hence will help in reasonable prediction of groundwater quality parameters.

Increase in the emission of Greenhouse Gases (GHS) is among the significant concerns of government, societies, and policymakers. Due to the highest share of carbon dioxide in the produced GHGs, it is necessary to assess the factors that influence its emission. Energy systems and economic activities noticeably influence the amount of carbon dioxide production of countries. In this article, Artificial Neural Network (ANN) in addition to a linear correlation used to predict carbon dioxide emission of four CIS countries, including Turkmenistan, Uzbekistan, Kazakhstan, and Azerbaijan based the consumption of various energy sources and GDP, as the economic indicator. According to the obtained data by the proposed models, carbon dioxide emission can be accurately estimated by utilizing the mentioned input data. Models’ R-squared value are 0.9997 and 0.9999 in the cases of applying the correlation and ANN-based model. Moreover, the average absolute relative deviations by utilizing the correlation and GMDH ANN are approximately 1.05% and 0.61%, respectively. These statistical values demonstrate more proper performance of the ANN-based model compared with the applied linear correlation.

Vertical Indoor Farming (VIF) with hydroponics offers a promising perspective for sustainable food production. Intelligent control of VIF system components plays a key role in reducing operating costs and increasing crop yields. Modern machine vision (MV) systems use Deep Learning (DL) in combination with camera systems for various tasks in agriculture, such as disease and nutrient deficiency detection, and flower and fruit identification and classification for pollination and harvesting. This study presents the applicability of MV technology with DL modelling to detect the growth stages of chilli plants using YOLOv8 networks. The influence of different bird’s eye and side view datasets and different YOLOv8 architectures was analysed. To generate the image data for training and testing the YOLO models, chilli plants were grown in a hydroponic environment and imaged throughout their life cycle using four camera systems. The growth stages were divided into growing, flowering and fruiting classes. All trained YOLOv8 models showed reliable identification of growth stages with high accuracy. The results indicate that models trained with data from both views show better generalisation. YOLO’s middle architecture achieved the best performance.

This work has its origin in intuitive physical and statistical considerations. The problem of optimizing an artificial neural network is treated as a physical system, composed of a conservative vector force field. The derived scalar potential is a measure of the potential energy of the network, a function of the distance between predictions and targets. Starting from some analogies with wave mechanics, the description of the sys-tem is justified with an eigenvalue equation that is a variant of the Schr˜odinger equation, in which the potential is defined by the mutual information between inputs and targets. The weights and parameters of the network, as well as those of the state function, are varied so as to minimize energy, using an equivalent of the variational theorem of wave mechanics. The minimum energy thus obtained implies the principle of minimum mutual information (MinMI). We also propose a definition of the potential work produced by the force field to bring a network from an arbitrary probability distribution to the potential-constrained system, which allows to establish a measure of the complexity of the system. At the end of the discussion we expose a recursive procedure that allows to refine the state function and bypass some initial assumptions, as well as a discussion of some topics in quantum mechanics applied to the formalism, such as the uncertainty principle and the temporal evolution of the system. Results demonstrate how the minimization of energy effectively leads to a decrease in the average error between network predictions and targets.

The research reported on this paper was aimed at improving the overall efficiency of a PDO certified artisanal cheese production process. Being a PDO certified foodstuff by the EU, it is considered to have properties and qualities determined by the geographical environment in which is made, with its production taking place in a specific and determined geographical location, in this case the Serra da Estrela region. In that sense, the authors conducted a mapping according to a systemic perspective of the processes involved in the context of manufacturing and distribution of certified Serra da Estrela cheese. Numerous methods were used throughout the process, such as a systemic design analysis, and techniques derived from ethnographic methods, which led to the collection of data in the field and consequently provided the immersion of the researcher in genuine work situations. Critical points were identified and emphasized in the systemic map with the purpose of encouraging initiatives to address and overcome the gaps and inefficiencies detected. The systemic design analysis triggered the development of design work. Observations following an ethnographic approach identified ergonomic risks in cheese making during the process of cutting excess chips, fostering the emergence of musculoskeletal disorders at the wrist. A tool that fits best to the task at hand was developed. A prototype of the new tool enabled collecting feedback from use in the work context, in order to inform product development. The domains of agricultural production and microbiology, considering the specific microorganisms developed trough the ripening process of the cheese, turned out to be aspects of high importance for the issue under focus, contributing to a broader understanding of the ripening process and its risks, simultaneously improving the efficiency and success of cheese production. If it were not for the systemic analysis, which served as a link between the boundaries of distinct domains such as the risk of microorganism contamination, ergonomics, energy efficiency, legislation and regulation policies, transportation challenges and economic viability, approached throughout the research. Simultaneously creating bridges between them, the various problems might not have been detected in the first place, as they are usually addressed in specialized disciplines, predetermined by the restrictions of each specific area of knowledge. As a consequence of the development of this research, which was based on an analysis that sought to establish possible connections between various disciplines and tried to constantly maintain a holistic perspective, making new connections and observing the issues from a new angle, apart from the already established methodologies. All this allowed to lay out the seeds for the development of a plan to tackle the critical points identified by the systemic analysis reported in this paper.

Gastric inflammation-related disorders are commonly observed digestive system illnesses char-acterized by the activation of proinflammatory cytokines, particularly tumor necrosis factor-α (TNF-α). This results in the induction of cyclooxygenase-2 (COX-2)/prostaglandin E2 (PEG2) and matrix metallopeptidase-9 (MMP-9). These factors contribute to the pathogenesis of gastric in-flammation disorders. We examined the preventive effects of Lonicera japonica Thunb. ethanol ex-tract (Lj-EtOH) on gastric inflammation induced by TNF-α in normal GES-1 cells. The GES-1 cell line was used to establish a model that simulated the overexpression of COX-2/PGE2 and MMP-9 proteins induced by TNF-α, to examine the anti-inflammatory properties of Lj extracts. The re-sults indicated that Lj-EtOH exhibits significant inhibitory effects on COX-2/PEG2 and MMP-9 ac-tivity, attenuates cell migration, and provides protection against TNF-α-induced gastric inflam-mation. The protective effects of Lj-EtOH are associated with the modulation of COX-2/PEG2 and MMP-9 through activation of TNFR–ERK 1/2 signaling pathways as well as the involvement of c-Fos and nuclear factor kappa B (NF-κB) signaling pathways. Based on our findings, Lj-EtOH ex-hibits a preventive effect on human gastric epithelial cells. Consequently, it may represent a novel treatment for the management of gastric inflammation.

Human factors are the things that go wrong in the interactions between a team of people and a system of technology. This is part of a broader transdisciplinary field called engineering psychology, which as the name suggests, draws from both engineering and psychology. Many, if not most, catastrophic accidents involve a socio-technical interaction, i.e. are not solely due to technology failure. Hence, there is a need to consider human factors in the development or deployment of any technical system. This article is about the human factors involved in an aviation accident in New Zealand between a Yak and a cherry picker. The types of human error are identified, and the barrier bowtie method is used to represent them. The analysis gives different insights into the accident compared to the formal accident report, and better represents the human error characteristics.

The features of a class of cubic curves with a shape factor are analyzed by means of the theory of envelope and topological mapping. The effects of the shape factor on the cubic curves are made clear. Necessary and sufficient conditions are derived for the curve to have one or two inflection points, a loop or a cusp, or to be locally or globally convex. Those conditions are completely characterized by the relative position of the edge vectors of the control polygon and the shape factor. The results are summarized in a shape diagram, which is useful when the cubic parametric curves are used for geometric modeling. Furthermore we discussed the influences of the shape factor on the shape diagram and the ability for adjusting the shape of the curve.

Respiratory rate is an important biomarker that indicates changes in the clinical condition of critically ill patients, so a surveillance tool that can accurately monitor the changing respiratory rate in real time is needed. Through investigating various pairs of machine learning models, we proposed new machine learning model for real-time respiratory rate estimation using photoplethysmogram. New photoplethysmogram-driven respiratory rate dataset(StMary) was collected from surgical intensive care unit of a tertiary referral hospital, using photoplethysmogram signal collector. For 50patients and 50healthy volunteers, 2-minute photoplethysmogram was collected for each subject twice. To evaluate the respiratory rate of subject, it was inputted into the deep neural network model we built, and dataset was splitted into training, validation, testing dataset, then 4-fold cross validation was exploited. Our deep neural network model trained with StMary and two public datasets(BIDMC and CapnoBase) individually, or selectively merged dataset had shown a low error rate in respiration rate measurements. Our model trained with StMary showed low mean absolute error score(1.0273±0.8965), and trained with 3 datasets(CapnoBase, BIDMC and StMary) showed a lower error rate(1.7359±1.6724) than the model trained with CapnoBase and BIDMC(1.9480±1.6751). We could verify the performance of model evaluating respiratory rate from photoplethysmogram, and our dataset could contribute as the clinical research data that supports artificial intelligence models evaluating respiratory rate and surveillance tools to test whether their monitoring function works properly.

Arctic sea ice prediction holds significant importance for facilitating Arctic route planning, optimizing fisheries management, and advancing the field of sea ice dynamics research. While various deep learning models have been developed for sea ice prediction, they predominantly operate at the seasonal or sub-seasonal scale, often focusing on localized areas, and few cater to full-region daily scale prediction. This study introduces the use of spatiotemporal sequence data prediction models, namely, the convolutional LSTM (ConvLSTM) and predictive recurrent neural network (PredRNN), for the prediction of sea ice concentration (SIC). Our analysis reveals that, when solely utilizing SIC historical data as the input, the ConvLSTM model outperforms the PredRNN model in SIC prediction. To enhance the model's capacity to capture spatiotemporal relationships between multiple variables, we expanded the range of input data types to form the ConvLSTM-multi and PredRNN-multi models. Experimental findings demonstrate that the ConvLSTM-multi model excels in assimilating the influence of reanalysis data on sea ice within the sea ice edge region, thus exhibiting superior performance in predicting daily Arctic SIC over the subsequent 10 days. Furthermore, sensitivity tests on various model parameters highlight the substantial impact of sea surface temperature and prediction date on the accuracy of daily sea ice prediction. Additionally, meteorological and oceanographic parameters primarily affect the prediction accuracy of the thin ice region at the edge of the sea ice.

Graft injury affects over 50% of liver transplant (LT) recipients, but non-invasive biomarkers to diagnose and guide treatment are currently limited. We aimed to develop a biomarker of graft injury by integrating serum metabolomic profiles with clinical variables. Serum from 55 LT recipients with biopsy confirmed metabolic-dysfunction associated steatohepatitis (MASH), T-cell mediated rejection (TCMR) and biliary complications was collected and processed using a combination of LC-MS/MS assay. The metabolomic profiles were integrated with clinical information using a multi-class Machine Learning (ML) classifier. The efficacy of the model was assessed through the evaluation of the Out-of-Bag (OOB) error estimate. Our ML model yielded an overall accuracy of 79.66% with an OOB estimate of the error rate at 19.75%. The model exhibited a maximum ability to distinguish MASH, with an OOB error estimate of 7.4% compared to 22.2% for biliary and 29.6% for TCMR. The metabolites serine and serotonin emerged as the topmost predictors. When predicting binary outcomes using 3 models: Biliary (biliary vs. rest), MASH (MASH vs. rest) and TCMR (TCMR vs. rest), the AUCs were 0.882, 0.972 and 0.96 respectively. Our ML tool integrating serum metabolites with clinical variables shows promise as a non-invasive, multi-class serum biomarker of graft pathology.

Sparse training (ST) aims to ameliorate deep learning by replacing fully connected artificial neural networks (ANNs) with sparse or ultra-sparse ones, such as brain networks are, therefore it might benefit to borrow brain-inspired learning paradigms from complex network intelligence theory. Here, we launch the ultra-sparse advantage challenge, whose goal is to offer evidence on the extent to which ultra-sparse (around 1% connection retained) topologies can achieve any leaning advantage against fully connected. Epitopological learning is a field of network science and complex network intelligence that studies how to implement learning on complex networks by changing the shape of their connectivity structure (epitopological plasticity). One way to implement Epitopological (epi- means new) Learning is via link prediction: predicting the likelihood of non-observed links to appear in the network. Cannistraci-Hebb learning theory inspired the CH3-L3 network automata rule for link prediction which is effective for general-purpose link prediction. Here, starting from CH3-L3 we propose Epitopological Sparse Meta-deep Learning (ESML) to apply Epitopological Learning to sparse training. In empirical experiments, we find that ESML learns ANNs with ultra-sparse hyperbolic (epi-)topology in which emerges a community layer organization that is meta-deep (meaning that each layer also has an internal depth due to power-law node hierarchy). Furthermore, we discover that ESML can in many cases automatically sparse the neurons during training (arriving even to 30% neurons left in hidden layers), this process of node dynamic removal is called percolation. Starting from this network science evidence, we design Cannistraci-Hebb training (CHT), a 4-step training methodology that puts ESML at its heart. We conduct experiments on 7 datasets and 5 network structures comparing CHT to dynamic sparse training SOTA algorithms and the fully connected counterparts. The results indicate that, with a mere 1% of links retained during training, CHT surpasses fully connected networks on VGG16, GoogLeNet, ResNet50, and ResNet152. This key finding is an evidence for ultra-sparse advantage and signs a milestone in deep learning. CHT acts akin to a gradient-free oracle that adopts CH3-L3-based epitopological learning to guide the placement of new links in the ultra-sparse network topology to facilitate sparse-weight gradient learning, and this in turn reduces the convergence time of ultra-sparse training. Finally, CHT offers the first examples of parsimony dynamic sparse training because, in many datasets, it can retain network performance by percolating and significantly reducing the node network size. Our code is available at: https://github.com/biomedical-cybernetics/Cannistraci-Hebb-training.

This paper proposes a radiation pattern synthesis of the almost periodic antenna arrays including mutual coupling effects (that extracted by the Floquet analysis according to our previous work), which principally has a high directivity and large bandwidth. For modeling the given structures, the moment method combined with the Generalized Equivalent Circuit (MoM-GEC) is proposed. The artificial neural network (ANN) as a powerful computational model has been successfully applied to the antenna array pattern synthesis. The results showed that the multilayer feedforward neural networks are rugged and can successfully and efficiently resolve various distinctive complex almost periodic antenna patterns (with different source amplitudes) (in particular, both periodic and randomly aperiodic structures are taken into account). However, the artificial neural network (ANN) is capable of quickly producing the synthesis results using generalization with the early stopping (ES) method. A significant time gain and memory consumption are achieved by using this given method to improve the generalization (called early stopping). To justify this work, several examples are developed and discussed.

Any effort to combat corruption can benefit from an examination of past and projected worldwide trends. In this paper, we forecast the level of corruption in countries by integrating an artificial neural network modeling and time series analysis. The data were obtained from 113 countries from 2007 to 2017. The study is carried out at two levels: (a) global level where all countries are considered as a monolithic group; and (b) cluster level, where countries are placed into groups based on their development-related attributes. For each cluster, we use the findings from our previous study on the cluster analysis of global corruption using machine learning methods that identified the four most influential corruption factors, and we use those as independent variables. Then, using the identified influential factors, we forecast the level of corruption in each cluster using a nonlinear autoregressive recurrent neural network with exogenous inputs (NARX), an artificial neural network technique. The NARX models were developed for each cluster, with the objective function in terms of the Corruption Perceptions Index (CPI). For each model, the optimal neural network is determined by finetuning the hyperparameters. The analysis was repeated for all countries as a single group. The accuracy of the models is assessed by comparing the mean square errors (MSE) of the time series models. The results suggest that the NARX artificial neural network technique yields reliable future values of CPI globally or for each cluster of countries. This can assist policymakers and organizations in assessing the expected efficacies of their current or future corruption control policies from a global perspective as well as for groups of countries.

Bicycle transport stands at the forefront of sustainable mobility initiatives, a cornerstone of European Union policy. While support for cycling is crucial, its advancement hinges upon the presence of high-quality, secure infrastructure for cyclists. Safety emerges as a paramount concern, influencing the viability of cycling as a mode of transportation, yet its perception varies among user demographics. In light of this, this article endeavors to examine and contrast cycling infrastructure across various European nations, alongside analyzing statistics pertaining to fatal traffic accidents involving cyclists. The findings underscore a substantial correlation between the quality of cycling infrastructure and the incidence of accidents. This correlation underscores the pressing need for robust infrastructure development and safety measures to bolster cycling as a safe and viable transportation option. By understanding the intricate interplay between infrastructure quality and safety outcomes, policymakers can better prioritize resources and enact measures to foster safer cycling environments, thus furthering the objectives of sustainable mobility on a continental scale.

The European Union Water Framework Directive (2000/60/EC; WFD) aims to achieve a good ecological and chemical status of all bodies of surface water by 2027. The development of an integrated guidance on surface water chemical monitoring (e.g. WFD Guidance Document No. 7/19) has been transferred into national German law (Ordinance for the Protection of Surface Waters, OGewV). For the majority of compounds, this act requires a monthly sampling frequency to assess the chemical water quality status of a surface water body. To evaluate the representativeness of the sampling strategy under the OGewV, high-frequency online monitoring data is investigated under different sampling scenarios and compared with current, monthly grab sampling strategy. About 23 million data points were analyzed for this study, three chemical parameters (dissolved oxygen, nitrate-nitrogen, chloride concentration) and discharge data were selected from four catchment of different sizes ranging from 51391 km² to 84 km² (Elbe, Vereinigte Mulde, Neiße and two stations at Lockwitzbach). In this paper we proposed short-term online-monitoring (STOM) as a sampling alternative. STOM considers the placement of online sensors over a limited duration and return interval. In general we: (I) compare the results of conventional grab sampling with STOM, (II) investigate the different performance of STOM and grab sampling using discharge data as proxy for analyzing event-mobilized pollutants and (III) investigate the related uncertainties and costs of both sampling methods. Results show, that STOM outperforms grab sampling for parameters where minimum/maximum concentrations are required by law as the probability to catch a single extreme value is higher with STOM. Furthermore, parameters showing a pronounced diurnal pattern, like dissolved oxygen, are also captured considerably better. The performance of STOM showed no substantial improvements for parameters with small concentration variability, as nitrogen-nitrate The analysis of discharge events as a proxy parameter for event-mobilized pollutants proved that the probability of capturing samples during events is significantly increased by STOM.

Equality and incomparability multi-label ranking have not been introduced to learning before. This paper proposes new native ranker neural network to address the problem of multi-label ranking including incomparable preference orders using a new activation and error functions and new architecture. Preference Neural Network PNN solves the multi-label ranking problem, where labels may have indifference preference orders or subgroups which are equally ranked. PNN is a nondeep, multiple-value neuron, single middle layer and one or more output layers network. PNN uses a novel positive smooth staircase (PSS) or smooth staircase (SS) activation function and represents preference orders and Spearman ranking correlation as objective functions. It is introduced in two types, Type A is traditional NN architecture and Type B uses expanding architecture by introducing new type of hidden neuron has multiple activation function in middle layer and duplicated output layers to reinforce the ranking by increasing the number of weights. PNN accepts single data instance as inputs and output neurons represent the number of labels and output value represents the preference value. PNN is evaluated using a new preference mining data set that contains repeated label values which have not experimented on before. SS and PS speed-up the learning and PNN outperforms five previously proposed methods for strict label ranking in terms of accurate results with high computational efficiency.

This paper proposes two max-pooling engines, named the RTB-MAXP engine and the CMB-MAXP engine, with a scalable window size parameter for FPGA-based convolutional neural network (CNN) implementation. The max-pooling operation for the CNN can be decomposed into two stages, i.e., a horizontal axis max-pooling operation and a vertical axis max-pooling operation. These two one-dimensional max-pooling operations are performed by tracking the rank of the values within the window in the RTB-MAXP engine and cascading the maximum operations of the values in CMB-MAXP engine. Both the RBM-MAXP engine and the CMB-MAXP engine were implemented using VHSIC Hardware Description Language (VHDL) and verified by simulations. They have been employed for and tested in our CNN accelerator targeting at the CNN model YOLOv4-CSP-S-Leaky for object detection.

This study investigated interactions between sugar-related dietary patterns (DP), personality traits, cognitive-behavioural, and emotional functioning. The study involved females aged 18-54. Data were collected between the Winter and Spring of 2020/21. The survey was conducted using anonymized questionnaires. The Ten-Item Personality Inventory (TIPI) was used to examine personality traits based on the Big Five Personality Trait Model. Three-Factor Eating Questionnaire (TFEQ) was used to measure eating behaviours: cogni-tive restraint (CR), uncontrolled eating (UE), and emotional eating (EE). The KomPAN question-naire collected the frequency of intake. Dietary patterns (DPs) were derived by principal component analysis (PCA). A logistic regression (OR) was applied to verify the association between the DPs, personality traits, cognitive-behavioural and emotional functioning. Three DPs were identified: sweet-western (SWDP), pro-healthy (PHDP) and dairy (DDP). Women with high conscientiousness were less likely, by 33%, to adhere to the upper tercile of SWDP and 80% more likely to the upper tercile of PHDP. Elevated CR intensity increased by almost 2-fold (OR: 1.93; p

Introduction: Hypertension is a serious public health problem in Morocco. The objective of this pilot study was to estimate the salt intake of Moroccan adults by measuring 24-hour urinary sodium excretion. Methods: 132 participants were recruited from the central region of Morocco. Sodium, potassium and creatinine levels were measured using the 24-hour urine samples. Additional data included anthropometric measurements and socio-demographic questionnaire. Results: The daily sodium, potassium and creatinine excretions were 2779.1±1334.9 mg, 1350.0±642.8 mg and 820.3 ± 381.2 mg, respectively. Data analysis revealed that 71.2% of the participants had a daily sodium intake more than 2000 mg (5g of salt) recommended by the WHO. The mean of potassium excretion was 1350.0±642.8 mg /day, this average was lower than 3.51g per day recommended by the WHO. Conclusion: Public health measures to reduce sodium and increase potassium consumption in order to decrease the population’s risk of high blood pressure and heart disease are recommended.

Background. Gene rearrangements affecting KMT2A are frequent in acute myeloid leukemia (AML) and are often associated with a poor prognosis. KMT2A gene fusions are often detected by chromosome banding analysis and confirmed by fluorescence in-situ hybridization. However, small intragenic insertions, termed KMT2A partial tandem duplication (PTD), are particularly challenging to detect using standard molecular and cytogenetic approaches. Methods. We have validated the use of a custom hybrid capture based next-generation sequencing (NGS) panel for comprehensive profiling of AML patients seen at our institution. This NGS panel targets the entire consensus coding DNA sequence of KMT2A; to deduce the presence of a PTD we used the relative ratio of KMT2A exons coverage. We sought to corroborate the KMT2A-PTD NGS results using (1) multiplex-ligation probe amplification (MLPA) and (2) optical genome mapping (OGM). Results. We analyzed 932 AML cases and identified 41 individuals harboring a KMT2A-PTD. MLPA, NGS and OGM confirmed the presence of a KMT2A-PTD in 22 of the cases analyzed where orthogonal testing was possible. Two false positive PTD calls by NGS could be explained by the presence of cryptic structural variants impacting KMT2A and interfering with PTD analysis. OGM revealed the nature of these previously undetected gene rearrangements in KMT2A, while MLPA yielded in-conclusive results. MLPA analysis for KMT2A-PTD is limited to exon 4, whereas NGS and OGM resolved KMT2A-PTD sizes and copy number levels. Conclusion. KMT2A-PTDs are complex gene rearrangements that cannot be fully ascertained using a single genomic platform. MLPA, NGS panels and OGM are complementary technologies applied in standard of care testing for AML patients. MLPA and NGS panels are designed for targeted copy number analysis; however, our results show that integration of concurrent genomic alterations is needed for accurate KMT2A-PTD identification. Unbalanced chromosomal rearrangements overlapping with KMT2A can interfere with the diagnostic sensitivity and specificity of copy number based KMT2A-PTD detection methodologies.

Amidst escalating environmental concerns, short natural fiber thermoplastic (SNFT) biocomposites have emerged as sustainable materials for the eco-friendly production of mechanical components. However, their limited durability has prompted research into the experimental evaluation of the deterioration of the mechanical characteristics of SNFT biocomposites, particularly under the influence of ultraviolet rays. However, conducting tests to evaluate the mechanical properties can be time-consuming and expensive. In this study, an artificial neural network (ANN) model was employed to predict the mechanical properties (tensile strength) and the impact performance (resistance and absorbed energy) of polypropylene reinforced with 30 wt.% short flax or wood pine fibers (referred to as PP30-F or PP30-P, respectively). Eight parameters were collected from experimental studies. The ANN input parameters comprised nondestructive test results, including mass, hardness, roughness, and natural frequencies, while the output parameters were the tensile strength, the maximum impact load and absorbed energy. The model was developed using the ANN toolbox in MATLAB. The linear coefficient of correlation and mean squared error were selected as the metrics for evaluating the performance function and accuracy of the ANN model. They calculate the relationship and the average squared difference between the predicted and actual values. The data analysis conducted by the models demonstrated exceptional predictive capability, achieving an accuracy rate exceeding 96%, which was deemed satisfactory. For both the PP30-F and PP30-P biocomposites, the ANN predictions deviated from the experimental data by 3, 5, and 6% about the impact load, absorbed energy, and tensile strength, respectively.

The most frequent, noticeable, and frequent natural calamity in the karakoram region is landslides. Extreme landslides have occurred frequently along Karakoram highway, particularly during the monsoon, causing a major loss of life and property. Therefore, it was necessary to look for a solution to increase growth and vigilance in order to lessen losses related to landslides caused by natural disasters. By utilizing contemporary technologies, an early warning system might be developed. Artificial neural networks (ANNs) are widely used nowadays across many industries. This paper's major goal is to provide new integrative models for assessing landslide susceptibility in a prone area of north of Pakistan. To do this, the training of an artificial neural network (ANN) is supervised using metaheuristic and Bayesian techniques: particle swarm optimization algorithm (PSO), Genetic algorithm (GA), Bayesian optimization Gaussian process (BO_GP), and Bayesian optimization Gaussian process (BO_TPE). 304 previous landslides and the eight most prevalent conditioning elements combine to form a geographical database. The models are hyper-parameter optimized, and the best ones are employed to generate the susceptibility maps. The area under the receiving operating characteristic curve (AUROC) accuracy index found demonstrated that the maps produced by both Bayesian and metaheuristic algorithms are highly accurate. The effectiveness and efficiency of applying artificial neural networks (ANNs) for landslide mapping, susceptibility analysis, and forecasting are studied in this research it’s observed from experimentation that the performance differences for GA, BO_GP, and PSO compared to BO_TPE are relatively small, ranging from 0.3166% to 1.8399%. This suggests that these techniques achieved comparable performance to BO_TPE in terms of AUC. However, it's important to note that the significance of these differences can vary depending on the specific context and requirements of the ML task. Additionally in this study, we explore eight feature selection algorithms to determine the geospatial variable importance for landslide susceptibility mapping along the KKH. The algorithms considered include Information Gain, Gain Ratio, OneR Classifier, Subset Evaluators, Principal Components, Relief Attribute Evaluator, Correlation, and Symmetrical Uncertainty. These algorithms enable us to evaluate the relevance and significance of different geospatial variables in predicting landslide susceptibility. By applying these feature selection algorithms, we aim to identify the most influential geospatial variables that contribute to landslide occurrences along the KKH. The algorithms encompass a diverse range of techniques, such as measuring entropy reduction, accounting for attribute bias, generating single rules, evaluating feature subsets, reducing dimensionality, and assessing correlation and information sharing. The findings of this study will provide valuable insights into the critical geospatial variables associated with landslide susceptibility along the KKH. These insights can aid in the development of effective landslide mitigation strategies, infrastructure planning, and targeted hazard management efforts. Additionally, the study contributes to the field of geospatial analysis by showcasing the applicability and effectiveness of various feature selection algorithms in the context of landslide susceptibility mapping.

COVID-19 outbreak started in the Chinese city of Wuhan and spread around the globe in months due to its high contagious level. Hence, this disease posed a great challenge to researchers and mathematicians. Numerous mathematical models have been suggested to visualize the spreading speed and trends of this pandemic. In this paper, a comparison of a widely established and accepted method, the Susceptible-Exposed-Infected-Quarantined-Recovered-Death-Insusceptible (SEIQRDP) model with a newly-proposed fractional-order SEIQRDP is studied. Densely populated Countries of Asia (Pakistan, India, and Bangladesh) have been chosen as data sets and both algorithms have been applied to their data. The same comparison technique has also been used on the data of two polar countries, New Zealand and Russia, that validated our findings. Error comparison of both algorithms has been recorded in a tabulated form which shows multi-fold erroneous trends over WHO data of selected countries.

Free-space communication is a leading component in global communications. Its advantages relate to a broader signal spread, no wiring, and ease of engagement. Satellite communication services became recently attractive to mega-companies that foresee an excellent opportunity to connect disconnected remote regions, serve emerging machine-to-machine communication, Internet-of-things connectivity, and more. Satellite communication links suffer from arbitrary weather phenomena such as clouds, rain, snow, fog, and dust. In addition, when signals approach the ground station, it has to overcome buildings blocking the direct access to the ground station. Therefore, satellites commonly use redundant signal strength to ensure constant and continuous signal transmission, resulting in excess energy consumption, challenging the limited power capacity generated by solar energy or the fixed amount of fuel. This research proposes LTSM, an artificial recurrent neural network technology that provides a time-dependent prediction of the expected attenuation level due to rain and fog and the signal strength that remained after crossing physical obstacles surrounding the ground station. The satellite transmitter is calibrated accordingly. The satellite outgoing signal strength is based on the predicted signal strength to ensure it will remain strong enough for the ground station to process it. The instant calibration eliminates the excess use of energy resulting in energy savings.

Lignocellulosic fibers are widely applied as composite reinforcement due to their properties. The thermal degradation behavior determines the maximum temperature in which the fiber can be applied without significant mass loss. It is possible to determine these temperatures using Thermogravimetric Analysis (TG). In particular, when curves are obtained at different heating rates, kinetic parameters can be determined and more detailed characteristics of the material are obtained. However, every curve obtained at a distinct heating rate demands material, cost, and time. Methods to predict thermogravimetric curves can be very useful in the materials science field and in this sense mathematical approaches are powerful tools if well employed. For this reason, in the present study, curaua TG curves were obtained at three different heating rates (5, 10, 20, and 40 °C.min-1) and Vyazovkin kinetic parameters were obtained. After, the experimental curves were fitted using an artificial neural network (ANN) approach followed by a Surface Response Methodology (SRM). Curves at any heating rate between the minimum and maximum experimental heating rates were obtained with high reliability. Finally, Vyazovkin kinetic parameters were tested again with the new curves showing similar kinetic parameters from the experimental ones. In conclusion, due to the capability to learn from the own data, ANN combined with SRM seems to be an excellent alternative to predict TG curves that do not test experimentally, opening the range of applications.

The technologies pertaining to ocean waves has been continuously improving since its creation and the major focus is to come up with accurate predication of power generation from the oceans waves. The precise forecast can not only reduce costs for investment but also it is essential for management and operation of electrical power. The purpose of the current paper is to numerically investigate a new economical wave energy converter named “Searaser”. The simulation is done with Flow-3D software which has high capability in analyzing the fluid solid interactions. by collecting the experimental data of another study and the exerted data which is from numerical simulation, the wind speed and output power are related with a long short term memory (LSTM). By doing comparative analysis between these data, it can be concluded that the artificial intelligence method is so accurate and fast. The network output figures show a good agreement and the root mean square is 0.49 in mean value which was related to the accuracy of LSTM method. One of the novelties of this study is to provide a scatter plot that generates power in terms of wind speed. Due to the accumulation of data, the power can be predicted for other wind speeds by using the intermediate values. Furthermore, the mathematical relation between the generated power and wave height was introduced by curve fitting the power function to the result of LSTM method.

Parasomnias are a group of sleep disorders characterized by abnormal and unpleasant motor, verbal or behavioral events that occur during sleep or during transitions between wake and sleep states. They disrupt sleep and can have a detrimental impact on the individual experiencing them. Our goal was to identify types of parasomnias and their prevalence in the post-secondary student population and to explore students' coping strategies for parasomnias they found distressing. Seventy-seven post-secondary students completed the 21-item Munich Parasomnia Screening (MUPS) frequency scale. They also rated, on a 10-point scale, how disturbing each parasomnia was. Not only did 92% percent of students report at least one parasomnia, but our results also indicate that the vast majority of students experienced more than one parasomnia. This led us to investigate the likelihood of the co-occurrence of different parasomnias. With respect to the level of subjectively experienced distress, the most prevalent parasomnias were not always the more disturbing ones. Coded open-ended responses about what students do about the disturbing parasomnias indicate that grounding strategies and physical manipulation of one’s body were the most common, although most participants indicated that in spite of distress, they do nothing to cope. In conclusion, our study found a strikingly high prevalence of parasomnias in this sample of young adults and a lack of knowledge about effective means of dealing with these.

This study presents a research plan that utilizes data obtained from wearable devices to identify human activities and gain insights into human behavior. We developed a model capable of classifying activities similar to human behavior and evaluated the effectiveness and generalization capabilities of this model. The data underwent initial preprocessing, including standardization and normalization. Additionally, recognizing the inherent similarities between human activity behaviors, we introduced a multi-layer classifier model. The first layer is a random forest model based on stepwise regression, which may encounter reduced accuracy for similar activities. The second layer employs a Support Vector Machine (SVM) model based on Kernel Fisher Discriminant Analysis (KFDA). KFDA is used to reduce the dimensionality of data points with potential confusion, followed by SVM for classification. The model was experimentally evaluated and applied to four benchmark datasets: UCI DSA, UCI HAR, WISDM, and IM-WSHA. The experimental results demonstrate that our approach achieved recognition accuracies of 99.71%, 98.71%, 99.12%, and 97.6% on these datasets, indicating excellent recognition performance. Furthermore, to assess the model's generalization ability, we performed K-fold cross-validation on the random forest model and utilized ROC curves for the SVM classifier. The results indicate that our multi-layer classifier model exhibits robust generalization capabilities.

The application of artificial intelligence to point-of-care testing (POCT) disease detection has become a hot research field, in which breath detection which detects the patient's exhaled VOCs combined with sensor arrays of Convolutional Neural Network (CNN) algorithms as a new lung cancer detection is attracting more researchers' attention. However, due to low accuracy, high complexity computation and large number of parameters make the CNN algorithms difficult transplant to the embedded system of POCT devices. A lightweight neural network (LTNet) in this work is proposed to deal with this problem, and meanwhile, achieve high-precision classification of acetone and ethanol gases, which are respiratory markers for lung cancer patients. Compared to currently popular lightweight CNN models such as EfficientNet, LTNet has fewer parameters (32K) and its training weight size is only 0.155 MB. LTNet achieved an overall classification accuracy of 99.06% and 99.14% in the own mixed gas dataset and the University of California (UCI) dataset, which are both higher than that of the five existing models’, and it also offers the shortest training (844.38s and 584.67s) and inference time (23s and 14s) in the same validation set. Compared to the existing CNN models, LTNet is more suitable for resource-limited POCT devices.

Health and well-being are a major concern for the elderly who experienced evacuation due to the 2011 Fukushima Daiichi Nuclear Power accident. This study examined the feasibility of a picture sound book with Ninja-essence to maintain or improve exercise habits and physical and mental conditions of the elderly affected by the Fukushima Daiichi Nuclear Power plant accident. We conducted a pre–post intervention study to evaluate a picture sound book with Ninja-essence for returnees and evacuees post lifting evacuation restrictions. In total, 29 people participated in this study. Residents in two groups, returnees and evacuees, were provided with the tool. Results of the pre–post changes were analyzed using descriptive statistics, i.e., Fisher’s exact test and t-test, and a significant difference was observed in both groups of participants between their left and right hand-grip strength, the maximum phonation time in the participants of the group that regularly engaged in exercise, and in the questions regarding swallowing exercises and singing songs or practicing words (p < 0.013 and 0.033); 16 of 29 participants reportedly enjoyed the program. The results demonstrated the future possibility of determining the improved outcome of this program in larger samples.

Structural deformations are one of the most significant factor that affects machine tool (MT) positioning accuracy. These induced errors are complex to be represented by a model, nevertheless they need to be evaluated and predicted in order to increase the machining performance. This paper presents a novel approach to calibrate a machine tool in real-time, analyzing the thermo-mechanical errors through Fibre Bragg Grating (FBG) sensors embedded in the MT frame. The proposed configuration consists of an adaptronic structure of passive materials, Carbon Fibre Reinforced Polymers (CFRP), equipped by FBG sensors that are able to measure in real-time the deformed conditions of the frame. By using a proper thermo-mechanical kinematic model, the displacement of the end effector may be predicted and corrected when it is subjected to external undesired factors. By starting from a set of FE simulations to develop a model able to describe the MT structure stresses, a prototype has been fabricated and tested. The scope was to compare the numerical model with the experimental tests using FBG sensors. The experimental campaign has been performed varying the structure temperature over time and measuring the tool tip point (TTP) positions. The obtained results showed a substantial matching between the real and the predicted position of TTP confirming the effectiveness of the proposed calibration system.

Background Homologous recombination deficiency (HRD) evolved into a major diagnostic marker in high grade ovarian cancer (HGOC) predicting the response to poly (Adenosine diphosphate-ribose) polymerase inhibitors (PARPi) and also platinum-based therapy. In addition to HRD, the type of peritoneal tumor spread influences treatment response and patient survival; miliary type tumor spread has poorer predicted outcome than non-miliary type tumor spread. Methods Known methods for HRD assessment were adapted for our technical requirements and the Predictive-value Integrated Genomic Instability Score (PIGIS) for HRD assessment evolved as an outcome. PIGIS was validated in HGOC samples from 122 patients. We used PIGIS to analyze whether the type of tumor spread correlated with HRD status and whether this had an impact on survival. Results We demonstrated that PIGIS can discriminate HRD positive from HRD negative samples. Tumors with miliary tumor spread are HRD negative and have a very bad prognosis with a progression free survival (PFS) of 15.6 months and an overall survival (OS) of 3.9 years. However, HRD negative non-miliary spreading tumors in our cohort had a much better prognosis (PFS 35.4 months, OS 8.9 years), similar to HRD positive tumors (PFS 34.7 months, OS 8.9 years). Conclusions Our results indicate that in a predominantly PARPi naïve cohort the type of tumor spread might be a better predictor of response to platinum sensitivity than HRD. It remains to be determined, whether this also applies for sensitivity to PARPi.

This study was undertaken to forecast waste generation rates of accommodation sector of North Cyprus as a case. Three predictor models including multiple linear regression (MLR), artificial neural networks (ANNs) and central composite design (CCD) were applied to predict the waste generation rate during the lean and peak seasons. ANN showed highest prediction performance, specifically, lowest values of the standard error of prediction (SEP = 2.153), mean absolute error (MAE=1.378) and highest R2 value (0.998) confirmed the accuracy of the model. The analysed wastes were categorised into recyclable, general waste and food residues. The authors estimated the total waste generated during the lean season as 2010.5 kg/day, in which large-sized hotel accounted for largest fraction (66.7%), followed by the medium hotels (19.4%) and guesthouse accounted for smallest part (2.6%). During the peak season, about 49.6% increases in the waste generation rates were obtained. Interestingly, 45% of the wastes were generated by the British tourists while the least waste was generated by African tourists (7.5%). The ANN predicted that the small and large hotels would produce 5.45 and 22.24 tons of waste by the year 2020, respectively. The findings herein are promising and useful in establishing a sustainable waste management system.

A large diversity of epigenetic factors, such as microRNAs and histones modifications, are known to be capable of regulating gene expression without altering DNA sequence itself. In particular, miR-1 is considered the first essential microRNA in cardiac development. In this study, miR-1 potential role in early cardiac chamber differentiation is analyzed through specific signaling pathways. For this, we performed in chick embryos functional experiments by means of miR-1 microinjections into the posterior cardiac precursors -of both primitive endocardial tubes- committed to sinoatrial region fates. Subsequently, embryos were subjected to whole mount in situ hybridization, immunohistochemistry and RT-qPCR analysis. As a relevant nov-elty, our results revealed that miR-1 increases Tbx5, Gata4 and AMHC1, while this microRNA diminishes Mef2c expression, during early differentiation of cardiac sinoatrial region. Further-more, we observed in this developmental context that miR-1 upregulates CRABPII and RARß, and downregulates CRABPI, which are three crucial factors in retinoic acid signaling pathway. Interestingly, we also noticed that miR-1 directly interacts with HDAC4 and Calmodulin, as well as with Erk2/MAPK1, which are three key factors actively involved in Mef2c regulation. Our study shows, for the first time, a key role of miR-1 as an epigenetic regulator in early differenti-ation of cardiac sinoatrial region through orchestrating opposite actions between retinoic acid and Mef2c, fundamental to properly assign cardiac cells to their respective heart chambers. A better understanding of those molecular mechanisms modulated by miR-1 will definitely help in fields applied to therapy and cardiac regeneration and repair.

Damage assessment is one of the most crucial issues for bridge engineers, especially for existing steel bridges. Among several methodologies, the vibration measurement test is a typical approach in which the natural frequency variation of the structure is monitored to detect the existence of damage. However, locating and quantifying the damage is still a big challenge. In this regard, the artificial intelligence (AI)-based approach seems a potential way to accomplish those obstacles. This study deploys a comprehensive campaign to determine all dynamic parameters of a pre-damage steel truss bridge structure. Based on the results of mode shape, natural frequency, and damping ratio, a finite element model (FEM) is created and keeps updating. The artificial intelligence network's input data will be analyzed and evaluation from damage cases. The trained artificial neural network model will be curated and evaluated to confirm the approach's feasibility. During the actual operational stage of the steel truss bridge, this damage assessment system is showing good performance in terms of monitoring the structural behavior of the bridge under some unexpected accidents.

Great Malang region is developing rapidly with the population increase and inhabitant`s activity, like migration and urbanization. Other activities like agricultural expansion as well as an uncontrolled residential development need to be monitored to avoid any negative impact in the future. The availability of free and open-source software, spatial high-resolution satellite imagery datasets, and powerful algorithms open the possibilities to map, monitor, and predict the future trend of land use land cover (LULC) changes. However, the accuracy and precision of this model is still in doubt, especially in the Great Malang region. Research is needed to provide a foundational basis and documentation on how the changes occur, where did the changes occur, and the accuracy of the predicted model. This study tries to answer those questions using the high spatial resolution of Sentinel-2 imageries. Combination of the fuzzy algorithm, artificial neural network, and cellular automata was utilized to process the datasets. We analysed four different scenarios of simulation and the result then compared. The different number of hidden layers and iteration was used and evaluated to understand the effect of different parameters in the prediction result. The best scenario was then used to predict future land use changes. This study has successfully produced the future LULC model of Great Malang region with high accuracy level (87%). The study also found that the land use transformation from agriculture to urban built-up area is relatively low, where changes of the built-up area over three periods of analysis are below than 5%. This is due to the physical condition of Great Malang region where mountainous areas are dominated.

Amid the swift progression of the global automobile industry, the aspiration for lightweight vehicle design has surfaced as a crucial approach to boost fuel efficiency and curtail environmental impact. The objective of this study revolves around achieving holistic optimization of vehicle structure via detailed scrutiny of vehicle process characteristics, amalgamated with a Back Propagation neural network (BPNN) optimized by a genetic algorithm (GA) and a topology optimization (TO) method.The process initiates with an examination of the vehicle's technical characteristics, succeeded by an optimization protocol that couples GA with BPNN. This exhaustive optimization procedure derives the best-fit values of design parameters and identifies the globally optimal lightweight design approach. Subsequently, a comprehensive structural optimization is actualized by modifying the topological distribution of the structure.A simulation experiment of the conceptual car body beam skeleton is conducted as a conclusive step, and the anti-collision capacity of the car body beam skeleton is assessed by measuring deformation intrusion. The findings reveal that in the vehicle topology optimization, a comparative analysis of pre and post-optimization results indicates an improved topological density across diverse sections. The topological density of the vehicle's frontal structure escalates from 0.75 to 0.8. Following optimization, the stiffness assessment records a marginal increase (within the range of 0.02–0.05), implying that the lightweight design does not compromise the general rigidity of the structure.The optimized body structure manifests superior crashworthiness in the crash test: the deformation intrusion diminishes by 27% in front-end collisions. In side impacts, the deformation and intrusion at critical points are reduced by 13.15% to 10% respectively. The comprehensive method proposed herein proves to be an efficient strategy to actualize the lightweight design of vehicles.

Activation Functions are crucial parts of the Deep Learning Artificial Neural Networks. From the Biological point of view, a neuron is just a node with many inputs and one output. A neural network consists of many interconnected neurons. It is a “simple” device that receives data at the input and provides a response. The function of neurons is to process and transmit information; the neuron is the basic unit in the nervous system. Carly Vandergriendt (2018) stated the human brain at birth consists of an estimated 100 billion Neurons. The ability of a machine to mimic human intelligence is called Machine Learning. Deep Learning Artificial Neural Networks was designed to work like a human brain with the aid of arbitrary choice of Non-linear Activation Functions. Currently, there is no rule of thumb on the choice of Activation Functions, “Try out different things and see what combinations lead to the best performance”, however, sincerely; the choice of Activation Functions should not be Trial and error. Jamilu (2019) proposed that Activation Functions shall be emanated from AI-ML-Purified Data Set and its choice shall satisfy Jameel’s ANNAF Stochastic and or Deterministic Criterion. The objectives of this paper are to propose instances where Deep Learning Artificial Neural Networks are SUPERINTELLIGENT. Using Jameel’s ANNAF Stochastic and or Deterministic Criterion, the paper proposed four classes where Deep Learning Artificial Neural Networks are Superintelligent namely; Stochastic Superintelligent, Deterministic Superintelligent, and Stochastic-Deterministic 1^st and 2^nd Levels Superintelligence. Also, a Normal Probabilistic-Deterministic case was proposed.

Predictive maintenance (PM) algorithms are widely applied for detecting operational anomalies on industrial processes to trigger maintenance before a possible breakdown; however, much less focus has been devoted to the use of such PM predictions as feedback in automated process control mechanisms. They usually integrate preventive solutions to protect the machines, usually causing downtimes. The premise of this study is to develop a holistic adaptive process scheduling mechanism that incorporates PM analysis as a safety component to optimize the operation mode of an industrial process toward preventing breakdowns while maintaining its availability and operational state, thereby reducing downtimes. As PM is largely a data-driven approach; hence, relies on the setup, we first compare different PM approaches and identify a one-class support vector machine (OCSVM) as the best performing option for the anomaly detection on our setup. Then, we propose a novel pipeline to integrate maintenance predictions into a real-time adaptive process scheduling mechanism. It schedules for the most suitable operation, i.e., optimizing for machine health and process efficiency, according to the abnormal readings. To demonstrate the pipeline on action, we implement our approach on a small-scale conveyor belt system utilizing our Internet of Things (IoT) framework. The results show that our PM-based adaptive process control provides an efficient process with less or no downtime. We also conclude that a PM approach does not provide sufficient efficiency without its integration into an autonomous planning process.

Proteomics research has become one of the most important topics in the fields of life science and natural science. At present, research on protein–protein interaction networks (PPINs) mainly focuses on detecting protein complexes or function modules. However, existing approaches are either ineffective or incomplete. In this paper, we investigate function module detection mechanisms in PPIN, including open databases, existing detection algorithms and recent solutions. After that, we describe the proposed solution based on simplified swarm optimization (SSO) algorithm and gene ontology knowledge. The proposed solution implements SSO algorithm for clustering proteins with similar function, and imports biological gene ontology knowledge for further identifying function complexes and improving detection accuracy. Furthermore, we use four different categories of species dataset for experiment: Fruitfly, Mouse, Scere, and Human. The testing and analysis result show that the proposed solution is feasible, efficient and could achieve a higher accuracy of prediction than existing approaches.