Fractional delay-Doppler (DD) channel estimation in Orthogonal Time Frequency Space (OTFS) systems poses a significant challenge considering the severe effects of Inter-Path Interference (IPI). To this end, several algorithms have been extensively explored in literature for accurate low-complexity channel estimation in both integer and fractional DDs scenarios. In this work, we develop a variant of the state-of-the-art Delay-Doppler Inter-Path Interference Cancellation (DDIPIC) algorithm which progressively cancels the IPI as estimates are obtained. The key advantage of the proposed approach is that it requires only a final refinement procedure reducing the complexity of the algorithm. Specifically, the time difference in latency between the proposed approach and the DDIPIC algorithm is almost proportional to the square of the number of estimated paths. Numerical results show that the proposed algorithm outperforms the other channel estimation schemes achieving lower Normalized Mean Square Error (NMSE) and Bit Error Rate (BER).

A well known result for the interference of two single-mode fields is that the degree of coherence and the degree of indistinguishablity are same when we consider the detection of a single photon. In this article we present the relation between degree of coherence, path indistinguishability and the fringe visibility considering interference of multiple number of single-mode fields while being interested in the detection of a single photon only . We will also mention how Born’s rule of interference for multiple sources is reflected in these results.

Pheochromocytoma and sympathetic paraganglioma (PPGL) are rare neuroendocrine tumors characterized by catecholamine production in the adrenal medulla and extra-adrenal paraganglia. PPGL with metastasis was termed malignant PPGL. However, the distinction between “benign” and “malignant” PPGLs has been debated. Currently, all PPGLs are believed to have some metastatic potential and are assigned malignant tumors (ICD-O/3) by the WHO Classification of Endocrine Organs (2017, 4th edition). Therefore, the previous categories benign and malignant PPGL have been eliminated in favor of a risk stratification approach. The Grading of Adrenal Pheochromocytoma and Paraganglioma (GAPP) is a tool for risk stratification for predicting metastasis and the prognosis of patients. At least 30% of PPGLs are hereditary, with 20 genes identified and genotype-phenotype correlations clarified. Of these, VHL, RET, and NF1 have been well investigated and are the primary cause of bilateral PCC. In addition, succinate dehydrogenase gene subunits SDHB and SDHD are strongly correlated with extra-adrenal location, younger age, multiple tumors, metastasis, and poor prognosis. Disease stratification by catecholamine phenotype and molecular profiling correlates with histological grading by GAPP. PPGLs should be understood comprehensively based on clinical, biochemical, molecular, and pathological data for patient care. A flow chart for pathological diagnosis is included.

The aim of this study was to examine the oxidation of human serum albumin (HSA) caused by oxidative stress after an exhaustive exercise such as ultra-marathon race. Thus, blood samples from 12 adult runners who underwent a 103 km mountain ultra-marathon race were collected pre- and 24, 48 and 72 h post race. HSA was partially purified using affinity chromatography and then was subjected to Western blot analysis for disulfide dimers determination, indicating oxidation. The results were correlated with those from a previous study in which the same samples were analyzed using different oxidative stress markers and a good correlation with protein carbonyls (PC) at all time points was observed. Moreover there was a significant correlation with static oxidation-reduction potential (sORP) at 24 h, and a negative correlation with capacity oxidation-reduction potential (cORP) at 24 and 48 h. In addition, an individual analysis of albumin dimers exhibited great inter-individual differences. This inter-individual variability in the oxidation of HSA may suggest different interventions (e.g. through diet) in order to confront the effects on athletes’ organism after a strenuous exercise. In conclusion, this study supported the importance of the assessment of albumin dimers as a predictive marker for exercise-induced oxidative stress.

The demonstration of compliance of rolling stock against disturbance limits for railway signaling, and in particular track circuits, is subject to a large deal of variability, caused by the diverse values of the electrical parameters of the railway line and resulting transfer functions, as well as operating conditions of rolling stock during tests. Instrumental uncertainty is evaluated with a Type B approach and shown to be much less than the experimental variability. Repeated test runs in acceleration, coasting, cruising, braking conditions are considered, deriving both max-hold (spread) and sample dispersion curves compared to the respective mean values (Type A approach to the evaluation of uncertainty). The major source of variability affecting a significant portion of the spectrum is caused by the superposed oscillations of the onboard LC filter, for which different choices of the transformation window duration are discussed. The test runs and the acquired data covered overall 1 day of tests along about 300 km of the Italian 3 kV DC railway network.

During choriogenesis in insects, chorion (eggshell) is formed by surrounding follicular epithelial cells in ovarioles. However, the regulatory endocrine factor(s) activating choriogenesis and the chemical components on eggshell deserve further exploration. In two representative Coleopterans, a Coccinellid Henosepilachna vigintioctopunctata and a Chrysomelid Leptinotarsa decemlineata, genes encoding the 20-hydroxyecdysone (20E) receptor heterodimer, ecdysone receptor (EcR) and ultraspiracle (USP), and two chitin biosynthesis enzymes UDP-N-acetylglucosamine pyrophosphorylase (UAP) and chitin synthase (ChS1), were highly expressed in ovaries of the young females. RNA interference (RNAi)-aided knockdown of either HvEcR or Hvusp in H. vigintioctopunctata inhibited oviposition, suppressed the expression of HvChS1, and lessened the positive signal of Calcofluor staining on the chorions, which suggests the reduction of a chitin-like substance (CLS) deposited on eggshells. Similarly, RNAi of LdEcR or Ldusp in L. decemlineata constrained oviposition, decreased the expression of LdUAP1 and LdChS1, and declined CLS contents in the resultant ovaries. Knockdown of LdUAP1 or LdChS1 caused similar defective phenotypes, i.e., reduced oviposition and CLS contents in the L. decemlineata ovaries. These results, for the first time, indicate that 20E signaling activates choriogenesis in two Coleopteran species. Moreover, our findings propose the deposition of a CLS on the chorions.

Light can interfere like a wave in a multi-path experiment, but it also has particle properties when interacting with matter. In a closer look, the interference pattern is created by many individual detections ("clicks"), which do not all occur simultaneously. An established assumption is therefore that a single light particle is capable of interfering with itself by superimposing all possibilities to get from the source to the detector. This is in stark contrast to our experience with macroscopic objects, which always "decide" in favour of only one of the alternative paths.In 2010, Jin et al. (Ref. 15) described an event-based model which allowed the authors to show that an interference pattern consisting of clicks can arise in a multi-path experiment even if photons, like macroscopic objects, only follow one path. To do this, photons must be able to transmit the information about their travelling duration to the detector and the detector must have a basic memory. A threshold function uses the message of several light quanta to decide whether a single detection is initiated, which is not the evidence for a single photon. In this "proof of principle", the authors do not claim that the detector function is a realistic one.In the present paper, this detector is replaced by a material consisting of ionizable molecules whose interaction with light takes place according to a modified version of Einstein's radiation laws. Based on this, a photon pair interaction mediated by matter takes place, which in a multi-path experiment generates an interference pattern of clicks at the detector, even if an arbitrary amount of time elapses between the individual detections. In the present model an interference pattern with minima that have less than half the intensity of the maxima is the result of a peculiar behaviour of the detector: In this case, the entirety of its electrons must be described as a unit (a “field”) with many equidistant energy levels. The results of a simulation are presented which enable the model to be tested in experiments.

Light can interfere like a wave in a multi-path experiment, but it also has particle properties when interacting with matter. In a closer look, the interference pattern is created by many individual detections ("clicks"), which do not all occur simultaneously. An established assumption is therefore that a single light particle is capable of interfering with itself by superimposing all possibilities to get from the source to the detector. This is in stark contrast to our experience with macroscopic objects, which always "decide" in favour of only one of the alternative paths.In 2010, Jin et al. (Ref. 15) described an event-based model which allowed the authors to show that an interference pattern consisting of clicks can arise in a multi-path experiment even if photons, like macroscopic objects, only follow one path. To do this, photons must be able to transmit the information about their travelling duration to the detector and the detector must have a basic memory. A threshold function uses the message of several light quanta to decide whether a single detection is initiated, which is not the evidence for a single photon. In this "proof of principle", the authors do not claim that the detector function is a realistic one.In the present paper, this detector is replaced by a material consisting of ionizable molecules whose interaction with light takes place according to a modified version of Einstein's radiation laws. Based on this, a photon pair interaction mediated by matter takes place, which in a multi-path experiment generates an interference pattern of clicks at the detector, even if an arbitrary amount of time elapses between the individual detections. In the present model an interference pattern with minima that have less than half the intensity of the maxima is the result of a peculiar behaviour of the detector: In this case, the entirety of its electrons must be described as a unit (a “field”) with many equidistant energy levels. The results of a simulation are presented which enable the model to be tested in experiments.

The organic fraction of municipal solid waste (OFMSW) is a significant environmental threat, and an economic and social challenge to manage. As such, the efficient treatment of OFMSW is a significant key factor in achieving sustainable waste management. Decentralized Composting (DC) develops a new framework of waste management. The DC Analysis Model (DCAM), proposed in our previous study, provides a powerful tool for decision makers, based on the quantification of the DC project characteristics. In this paper, we focus on the qualitative analysis as a complementary tool to support decision making, in cases where quantitative analysis is unequivocal. The qualitative analysis identifies the main players in the field, the critical stakeholders and the potential conflicts between them. It also reveals the root problems and the core competencies for the project's implementation. DCAM qualitative analysis in Shefa-Amr (case study) indicates that unresolved root problems, such as the “lack of national regulation”, “clear ownership of the project” and “lack of ongoing budget” can result in an unsustainable composting system. Countering that, “the commitment of the municipality”, together with “economic viability” and securing “suitable areas for placing composters” are among the most important core competencies for the effective implementation of DC projects.

Aiming at effectively generating safe and reliable motion paths for quadruped robots, a hierar-chical path planning approach driven by dynamic 3D point cloud is proposed in this article. The developed path planning model is essentially constituted of two layers: global path planning layer and local path planning layer. At the global path planning layer, a new method is proposed for calculating terrain potential field based on point cloud height segmentation. Variable step size is employed to improve the path smoothness. At the local path planning layer, a real-time prediction method for potential collision area and a strategy for temporary target point selection is developed. Quadruped robot experiments were carried out in an outdoor complex environment. The experi-mental results verified that, for global path planning, the smoothness of the path is improved and the complexity of the passing ground is reduced. The effective step size is increased by a maxi-mum of 13.4 times, and the number of iterations is decreased by up to 1/6, compared with the traditional fixed step size planning algorithm. For local path planning, the path length is short-ened by 20%, more efficient dynamic obstacle avoidance and more stable velocity planning are achieved by using the improved dynamic window approach (DWA).

This study explores the complexities of sport manager selection, investigating the impact of affirmative action, recruitment strategies, organizational culture, diversity initiatives in board selection, and career advancement insights from coaches' perspectives. To conduct this investigation, a purposive sampling technique was employed, selecting 65 prominent sports managers and coaches from Romania. Participants, aged between 35 to 58 years old, boasted an average of 10 to 20 years of sports experience and were chosen based on specific criteria, including academic qualifications. Data collection occurred over an extended period, spanning from fall 2022 to spring 2024, through semi-structured interviews with sport managers and coaches. The findings unveiled persistent challenges in effectively implementing affirmative action measures, as sport managers grapple with balancing the promotion of deserving candidates while maintaining continuity in board culture. Achieving meaningful diversity necessitates nuanced approaches that consider both candidate quality and cultural compatibility. Moreover, the study sheds light on coaches' perspectives when considering executive council positions, highlighting various pathways to career advancement. Recruitment practices prioritized informal methods, emphasizing board cohesion. Despite the recognized importance of diversity, challenges persist in selecting candidates solely based on demographic representation. The study provides valuable insights into promoting diversity and inclusivity within sports organizations' executive councils. Future research directions may include exploring longitudinal trends and delving into the qualitative experiences of underrepresented groups, with the aim of advancing understanding and promoting equity within sports organizations.

The number of physical devices connected to the Internet such as vehicles, household appliances and other "things" has been steadily increasing in recent years, thus forming the basis for the Internet of Things (IoT). IoT ecosystem extends beyond country borders and application domains, combining thousands of versatile devices that differ in terms of their structures, capabilities, and available resources. It is therefore not surprising that the landscape of wireless communication technologies and the degree of IoT devices available today is excessively broad and diverse. Interference between networks leads to frame collisions and consequent packet loss. Frame collisions occur when two or more packets overlap in time and frequency and use the same LoRa parameters, i.e. the same spreading factor (SF), bandwidth (BW) and carrier frequency (CF). When most devices use the same configuration, collision probability is higher. The probability of frame collisions is also affected by traffic characteristics, particularly the periodicity of the transmission and the payload size. Larger payload sizes and more frequent transmissions accumulate with higher time on air (ToA) and channel occupancy [1]. Transmission powers and the location of the gateways also influences this situation. The aim of this experimental work is to verify the effects of collisions and interference in LoRaWAN, regarding the periodicity of transmissions and the payload sizes. The hardware used is an Arduino board programmed in C/C++, a LoRa Bee module operating at a frequency of 868 MHz and a LoRaWAN LG02 gateway. Different scenarios were tested in an outdoor environment, with Line of Sight and Non-Line of Sight, and different variables such as: SFs equal to 7, 9 and 12; distances of 20, 40 and 60 meters and different data sizes of 14, 32 and 51 bytes, over the same channel. The packets with different SF’s and different data sizes were transmitted in a (pseudo) random way, one after the other, overlapping different SFs in the same channel and testing this way (theoretical) orthogonality among them. By fixing the bandwidth in 125 kHz, and testing different SFs we intend to increase the probability of cause packet loss by applying to our connection a combination of emitted power/short distance that leaves an interference power received, strong enough [2] for the effect. We validate our conclusions by analyzing ToA according with RSSI and different data sizes, the RSSI for different SFs and different data sizes and finally the packet loss through the PDR-Packet Delivery Ratio for a better understanding of the reliability of packet transmission in our link.

Modular steel buildings (MSBs) interlocking inter-module connections (IMCs) have piqued researchers’ interest. However, the existing literature has not yet studied the optimisation of its plate thicknesses. This paper, therefore, focuses on optimising interlocking (IMCs) plate thickness in (MSBs), leveraging previous experimental and numerical simulation methodologies. Various numerical models for four MSBs interlocking (IMCs) with plate thicknesses (4 mm, 6 mm, 10 mm, and 12 mm) were developed under compression loading conditions. The study’s novelty lay in its comprehensive parametric analysis, which evaluated the slip phenomenon in (MSBs) connections and introduced a slip prediction model validated against empirical data. Further innovative machine learning approach was utilised to predict slip values based on applied force through a random forest regression model trained using the 'Treebagger' function. Sensitivity analysis and comparisons with alternative methods were utilised to underscore the reliability and applicability of the findings. The results showed that 11.03 mm was the optimal plate thickness for interlocking (IMCs) in modular steel buildings, with up to 8.08% reduced material costs. Increasing plate thickness boosts its deformation resistance by up to 50.75%. ‘TreeBagger’ random forest for anomaly detection and machine learning improves slip prediction up to 7% at higher force levels.

Inter-industry has various capital structures to take advantage of growth opportunities due to agency differences and information asymmetric problems. This research aims to analyze: (1) the differences in leverage between industries; (2) the impact of shareholders-debtholders conflict and information asymmetric on growth opportunities. The findings show that there are differences in leverage between industries. However, they are relatively stable and not excessive for assets to prevent conflicts between managers and shareholders and debtholders. Equity is also not used to utilize growth because it is used to reduce the discretionary power (dilution) of shareholders. As a result, the use of opportunities and growth is limited.

The thesis proposes a argument that a mass point moving in a horizontal circle on the Earth's surface can generate a radial centrifugal force of the Earth's center of mass, thus realizing an unconventional anti-gravity path. And through the theoretical analysis of the difference in the distribution of gravitational acceleration at different latitudes caused by the rotation of the earth, and the centrifugal force of a mass point moving in a horizontal circle on the earth's surface is analyzed, the validity of the argument is demonstrated. At the same time, the paper puts forward two possible basic principles, and makes theoretical analysis and demonstration. Conceive of the concrete experimental verification of principle two is proposed. Four technical schemes for antigravity ascent are proposed and basic analysis is made. On the premise of not fully considering the practical technical ability, it is theoretically proved that three of them have realistic operability and development potential. In theory, this paper opens up a different way of anti-gravity for human beings, which will bring new ideas and prospects for human beings to get rid of the bondage of gravity.

The challenging terrain and deep ravines characteristic of mountainous regions often result in slower path planning and suboptimal flight paths for Unmanned Aerial Vehicles (UAVs) when traditional meta-heuristic optimization algorithms are employed. This study investigates the application of an Improved Enhanced Snake Optimizer (IESO) for three-dimensional path planning in a simulated rugged mountainous terrain. The initialization process in the enhanced snake optimizer is refined by integrating the Chebyshev chaotic map. Additionally, a non-monotonic factor is introduced to modulate the "temperature," and a boundary condition is incorporated into the dynamic opposition learning mechanism. These modifications collectively reduce the likelihood of population convergence to local optima during optimization. The feasibility of IESO is validated through time complexity and global convergence analyses. Comparative simulation experiments benchmarked IESO against five state-of-the-art optimization algorithms across test functions and path-planning simulated scenarios. The experimental results indicate that the enhanced algorithm achieves superior optimization precision, faster convergence speeds, and improved quality in the planned trajectories by 30%.

Job characteristics shape organizational sustainability, conferring tangible benefits to employees. Job characteristics shape attitudes toward work, such as satisfaction and engagement, and are related to the well-being and health of employees. The aim of the study was to determine and describe the role of work engagement and support at work in the relation between selected job characteristics (organizational justice, job control, and role clarity) and self-rated health. The study was conducted on a sample of 368 employees representing various industries. The study used: Utrecht Work Engagement Scale (UWES), Organizational Justice Survey, Coworker Support Scale, Supervisor Support Scale, Role Clarity Scale, Job Control Scale. Cantril ladder was used to measure self-rated health. The presented study established the importance of lower scores on the UWES subscale: dedication as a significant moderator of the examined correlations. In relation to the correlation: justice and its dimensions, and self-rated health, support from supervisors showed a greater effect than that from coworkers. The conducted study expands knowledge on the formation of employees' self-rated health through the sense of justice experienced within the organization. The results obtained are applicable to organizational practice. This finding highlights the importance of supporting organizational justice, which contributes to employee well-being (particularly when combined with high levels of work engagement and supervisor support) and ultimately increases organizational sustainability. Further research can be continued taking into account the limitations of the previous procedure of selecting people for the study and the measurement tools used.

Variance-driven decomposition based on the singular spectrum analysis of the European Project for Ice Coring in Antarctica (EPICA) dD, CO2 and CH4 records allowed a novel quantitative structural interpretation of all glacial/interglacial cycles and glacial terminations of the last 800 kyr. This bottom-up approach used the response components of EPICA stacked records to reconstruct the envelope of the thermal response through a physical interference model. The aim was to improve the understanding regarding the features of intensity, amplitude, and asymmetry of 73 marine isotope stages (MIS) and seven terminations. The Antarctic stack record can be described by a variance-weighted interference model of ten thermal waves of different origins (mid-term oscillation, orbitals and suborbitals) that stochastically interfere at a given time according to their relative differences in frequency, intensity, and polarity. Interglacial/glacial stages resulted from constructive interference and bipolar amplification of warming/cooling responses, respectively. The low intensity MISs (including 90% of substages) and the unbiased-dated terminations fell in the low interference regions where dominant destructive patterns minimise the thermal envelope. The positive skewness of the EPICA stack resulted from the constructive interference with a strong bias in the warming direction, especially after the Mid-Brunhes Event. Duration analysis of short eccentricity hemicycles exhibited an intrinsic unexpectedly prolonged mean cooling in the nominal solution (5.8 kyr) and its EPICA response as well (8.6 kyr), along with an interference-induced asymmetry (21.1 kyr). The overall effect resulted in the saw-tooth shape of glacial cycles which is heavily induced by interference and related to the intermediate feedback mechanisms controlled by short eccentricity.

The paper provides a methodological framework based on Multiple Criteria Decision Aid methods for determining relative regional vulnerabilities associated with forest fires that occurred during a given period. Different notions of ex-post vulnerability are defined based on the forest area burned and the frequency of forest fires, and their relation to the regions’ area and several socioeconomic characteristics. The methodology is applied to Greece and its administrative regions for the period 2000–2022. Linking the forest fire events with summer and spring temperatures and precipitation and using econometric count data analysis, the paper explores the climatic drivers of forest fire occurrence and provides projections of the expected change in the frequency of fires of specific size classes conditional on the evolution of mean seasonal regional temperature and precipitation according to IPCC scenarios. The results regarding relative regional vulnerabilities and expected forest fires could be useful in designing policies for preserving forests as natural capital and promoting sustainability.

The uncertainty in the secondary path of an Active Noise Control (ANC) headphone affects the waterbed effect and stability of the feedback system. This study focuses on the uncertainty of the secondary path when real users wear headphones, and proposes a new uncertainty constraint based on the measured results of the secondary path transfer function under different wearing conditions of dummy head and limited subjects. This constraint and a cascaded second-order infinite impulse response filter with fixed coefficients are used to formulate a control strategic function, which is optimized by the Improved Grey Wolf Optimizer (IGWO) algorithm to obtain the optimal controller with better noise reduction performance. The proposed method and simulation model are validated based on the experimental test results. The results demonstrate that the safety factor and waterbed suppressing factor contained in the proposed uncertainty constraint ensures more stable noise reduction and effective suppression of the waterbed effect for new subjects without a priori data.

1. Heterospecific pollen interference has recently been proposed as a mechanism contributing to the success of alien invaders, as heterospecific pollen of alien plants interferes with the reproduction of natives by reducing fruit and seed set. However, no study has looked at the opposite interaction. Moreover, few studies have considered the roles of phylogenetic and trait distances between pollen donors and recipients. 2. We did a large multi-species experiment in which we used alien and native species both as pollen recipients and as pollen donors, and included phylogenetic as well as trait distance as explanatory variables. 3. We found that both alien and native recipients suffered from heterospecific pollen from donors of the opposite status in terms of seed and fruit set. Phylogenetic distance and trait distance both affected heterospecific pollen interference, but the effect depended on recipient and donor statuses. 4. We conclude that heterospecific pollen interference affects both native and alien recipients, thus indirectly altering community composition and increasing biotic resistance against invaders.

Due to the long-term deformation settlement of foundations, issues such as damage and functional failure of buildings and structures have long been of concern in the engineering field. The creep of soil is one of the primary causes leading to long-term deformation of foundations. In this paper, the consolidation deformation, creep characteristics, and creep model of reconstituted saturated silty clay were studied by isotropic compression test and triaxial shear creep test. The results show that for the isotropic compression test, although the applied load adopts different stages of loading, as long as the final applied confining pressure is the same, the number of stages applied by the confining pressure has little effect on the final isotropic consolidation deformation of the sample and the triaxial undrained shear strength after creep. However, for the triaxial shear creep test, it is found that under the same final deviatoric stress, the final deviatoric strain of the sample is closely related to the number of loading stages of deviatoric stress. It shows that the more loading stages of the sample loaded with the same deviatoric stress, the smaller the final deviatoric strain, and the triaxial undrained shear strength of the sample after creep will increase. In addition, it is reasonable to determine the pore pressure dissipation of the sample to 95%((u0-u0)/u0=95%) as the main consolidation end time (tEOP) of the sample. The isotropic consolidation creep curves and the triaxial shear creep curves show certain nonlinearity. Then the logarithmic model and the hyperbolic model were used to fit the creep curves of the samples. It is found that the hyperbolic model has a better fitting effect than the logarithmic model, but for the triaxial shear creep test, the creep parameters of the sample change greatly. Therefore, studying the creep characteristics of soil under different pre-loading steps is of significant engineering importance for evaluating the long-term deformation of underground structures.

Businesses use technological and social media marketing to respond to the Covid-19 pandemic. This study aims to understand better the factors that impact the spread of new technologies, the effectiveness of social media advertising, and the longevity of businesses. The study used a quantitative strategy based on partial least squares structural equation modeling to learn about the phenomenon of interest as much as possible. Dhaka, Bangladesh, small and medium-sized businesses participated in the survey. According to the findings, the popularity of internet and e-business technologies may be attributed to their apparent usefulness and ease of use. It is connecting internet/e-business technology, social media marketing, and the long-term success of small and medium-sized enterprises. Still, the expense factor was insufficient to prove that SMEs engage in social media advertising. Mediating effects between components may be better understood via internet/e-business technology and social media marketing, as shown by this study. This study is the first of its kind in Bangladesh and sheds light on the resilience of SMEs in the face of the Covivirus-19 pandemic, notwithstanding its focus on the capital city of Dhaka.

The Science-Sustainability poses an interdisciplinary paradox. On the one hand, the science for sustainability has increased in OECD economies in and in China as well as in the US in particular; on the other hand; the sustainability situation has worsened (Co2 emission has risen). On the face value, the adverse correlation shows a paradox. However, without explicating the science-sustainability relationship, it leads to a premature conclusion. In this study, we have drawn on three concrete questions for concrete answers. First, whether and how interdisciplinary sciences—energy science and environmental science—contribute to the sustainability. Second, whether and how the Sino-US inter-institutional analysis varies in the science-sustainability paradox. The empirical analysis from a panel data in the interdisciplinary and inter-institutional context show mixed patterns in three ways. First, the increase in the environmental science shows an improvement in the sustainability; the energy science shows a decline in the sustainability. Second, the Chinese environmental science has a comparative advantage to American environment science for the sustainability development, and the Chinese energy science has a comparative disadvantage to the US in the sustainability development. Third, the environmental science mediates the energy science in the science-sustainability relationships. Standing alone, the increase in the energy science harms sustainability; mediated by environmental science, it benefits sustainability. The study explains the adverse role of energy science in Jevons Paradox. The study also offers some policy paths for further research how capitalisms differently innovate, form strategies, and implement the practice.

Three-dimensional transfer functions (3D TFs) are generally assumed to fully describe the transfer behavior of optical topography measuring instruments such as coherence scanning interferometers in the spatial frequency domain. Therefore, 3D TFs are supposed to be independent of the surface under investigation resulting in a clear separation of surface properties and transfer characteristics. In this paper we show that the 3D TF of an interference microscope differs depending on whether the object is specularly reflecting or consists of point scatterers. In addition to the 3D TF of a point scatterer, we will derive an analytical expression for the 3D TF corresponding to specular surfaces and demonstrate this as being most relevant in practical applications of coherence scanning interferometry (CSI). We additionally study the effects of temporal coherence and disclose, that in conventional CSI temporal coherence effects dominate. However, narrowband light sources are advantageous if high spatial frequency components of weak phase objects are to be resolved, whereas for low-frequency phase objects of higher amplitude the temporal coherence is less affecting. Finally, we present an approach that explains the different transfer characteristics of coherence peak and phase detection in CSI signal analysis.

This manuscript proposes a novel tangent-graph-based method that provides all distinctive topology paths, as a set of trajectories that can not be transformed into each other by gradual bending and stretching without colliding with obstacles. As the global optimal trajectory (limited by dynamic constraints) may not correspond to the shortest path (almost without dynamic constraints), it is important to provide all distinctive topology paths rather than just the globally shortest one. One of the application is provide initial paths for trajectory planning methods, such as time elastic band (TEB) and dynamic window approach (DWA). Considering that a mobile platform is always working in a dynamic changing environment and that update the whole graph is time consuming, a dynamic rectify method is proposed to update tangents according to local map provided by sensor reading. Finally, results under real grid maps are presented.

This article proposes an interferometer which should in principle split further an initially split beam to yield new sets of beams, effectively multiplying the number of beams that can be subjected to detectable interference. It can be considered a modification to the Michelson interferometer that introduces additional arrays of beam splitters, mirrors and detectors. It is expected of the interferometer to provide us with a set or sets of data holding details of phase changes in multiple interference patterns detectable by multiple detectors, enabling comparative analysis of data for multiple interference patterns recorded from a single measurement or activity. The number of multiplied beams possible is not limited, as it only depends on the specific amount of beam splitters required for certain experiments and practicals. The interference of multiple beams may improve sensitivity and detection for instrumentation purposes. The use of multiplied beam interferometry may also extend to quantum computation, particularly in linear optical quantum computation scheme as it enable production of multiple coherent beams which may exhibit properties of entanglement, making it suitable for developing optical multi-qubit systems.

We present an analysis of recent experiments in femtoscopy by the STAR collaboration in terms of the protocol of entanglement witnessing involving purity measurements. The entanglement is between the charge and momentum degrees of freedom of pions and the state purity measurements ultimately rely on the bosonic nature of the detected pions. The pion experiment is intended to measure the size of nuclei and the distance between the nuclei involved, however it indirectly confirms that the states of dfferently charged pions are entangled through an entanglement witness based on the purity of various pionic states. The entangled state of pions can be modelled straightforwardly dynamically using a simple Hamiltonian. Quantum indistinguishability plays a key role in this analysis and we make comparison with the equivalent photonic experiments.

The presence of the quantum Rayleigh scattering, or spontaneous emission, inside a dielectric medium such as a beam splitter or an interferometric filter, prevents a single-photon from propagating in a straight-line. Modelling a beam splitter by means of a unitary transformation is physically meaningless because of the loss of photons. Additional missing elements from the conventional theory are: 1) the quantum Rayleigh stimulated emission which can form groups of photons of the same frequencies, and 2) the unavoidable parametric amplification of single-photons in the original parametric crystal. An interference filter disturbs, through multiple internal reflections, the original stream of single-photons, thereby confirming the existence of groups of photons being spread out to lengthen the coherence time. The approach of modelling individual, single measurements with statistical ensemble probability amplitudes leads to the counterintuitive explanations of the experimental outcomes and should be replaced with pure states describing instantaneous measurements which are afterwards averaged.

The role of innate immunity in neutralization of viral infections (including COVID-19) and forming long-lasting and specific immune memory is considered. It is assumed that antiviral protection is generated by the mechanism of RNA interference (RNAi) and is based on the presence of specific viral patterns in the DNA library of the host cells.

Satellite communication (Satcom) is an artificial geostationary satellite that facilitates a wide range of telecommunications. Considering its quality of service (QoS) and security is crucial in government/military applications. The most challenging situation for efficient Satcom is radio frequency interference (RFI) environment. Thus, it is necessary to ensure that transmissions are incorruptible or at least sense the quality of its spectrum. This paper presents a new method to recognize received signal characteristics using a hierarchical classification in a multi-layer perceptron neural network. We consider signal modulation and the type of RFI as the characteristics of a real-time video stream transmitted in the direct broadcast satellite. Four different modulation types are investigated in this study. Moreover, the combination of the communication signal with various kinds of interference and their effects on the classification method widely have been analyzed. Besides, two robust feature selection techniques have been developed to reduce the data-set dimensional, which leads to optimizing the classification process. The results show that the Genetic Algorithm (GA) slightly outperforms Principal Component Analysis (PCA) for feature selection. Furthermore, the robustness of the proposed techniques is assessed to detect unknown signals at different signal to noise ratios.

Artificial intelligence provides a new research concept for digital image processing. However, at present, artificial intelligence is rarely introduced into the teaching of digital image processing in colleges and universities, and there are problems such as obsolete teaching content, single teaching methods, and simple course experiments, which affect the teaching effect and are not conducive to the cultivation of comprehensive and innovative talents. Digital image processing technology brings more possibilities to communication engineering and makes communication more convenient. For example, video calls and photo transmission make people's communication methods in daily life more and more diversified. Time and space limitations allow people to meet online, creating more communication possibilities. However, there are still many problems and methods worthy of in-depth exploration. Therefore, this paper has a comprehensive understanding and mastery of the traditional and deep learning methods of digital image processing to improve the relevant project practice and scientific research exploration ability and refer for similar research conclusions.

Dairy farming dates to the early Neolithic era in Europe, Middle East, Asia, and Africa. Over time, the industry has evolved from small ranches and farmhouses milk processing units to large, intensive dairy farms and big, high-tech processing units. Despite the industry’s contribution to the economy and food production, multiple studies have tainted cattle farming as a main contributor to climate change. This study explores literature in dairy farming and sustainable development goals (SDGs) to identify current scholarly developments since the formulation and adoption of SDGs in 2015 and themes for future research. This paper argues that dairy animals are not the source of sustainability shortfalls as depicted by multiple scholarly articles, but human processes associated with dairy farming. Data was analyzed using R package, Excel, NVIVO, and VoS Viewer. A review of literature shows that dairy farming and its contribution to sustainability has gained more intensive scientific interest since 2015. Moreover, livestock management, feed production and management, stakeholder’s management, logistics and supply chain management, and waste management are the sources of environmental adversities associated with dairy farming. Notably, these are human processes developed from commercialization of dairy farming and involve multiple stakeholders across the supply chain. While solutions are embedded within these processes, innovation emerges as a key driver of sustainability and source of opportunities to strengthen sustainability in dairy farming sector and achieve the sustainable development goals.

The blood counts of α thalassemia carriers (α-thal) are similar to those of β thalassemia carriers, except for Hgb A2 that is not elevated. The objective of this study was to determine whether mathematical formulas are effective for detecting suspected α-thal. The data were obtained from the database of the prevention program for detecting couples at risk for having a child with hemoglobinopathy. RBC indices were analyzed using mathematical formulas and the sensitivity and negative predictive value (NPV) calculated. Among 1334 blood counts suspected α-thal analyzed, only the Shine&Lal and the Support Vector Machine formulas revealed high sensitivity and NPV. Sensitivity was 85.54 and 99.33% and NPV 98.93 and 99.93%, respectively. Molecular defects were found in 291, 81 had normal α genes. Molecular analysis was not performed in 962. Based on these results, mathematical formulas incorporating one of these reliable formulas for detecting suspected α or β thalassemia carriers in the program of the automatic analyzers can flag these results and increase the awareness of the primary physicians about the carrier risk and send an alert with a recommendation for further testing.

Background: To investigate the preoperative clinical and radiological factors that predict the development of a postoperative intraabdominal abscess (IAA) in patients with acute appendicitis who were treated by laparoscopic appendectomy (LA). Methods: Two hundred sixteen patients with pathologically proven acute appendicitis underwent LA between January 2013 and March 2018 in our department. Of these, 147 patients were diagnosed with complicated appendicitis (CA) (CA group), while the other 69 patients were diagnosed with simple appendicitis (SA) (SA group). We compared the perioperative clinical and radiographic factors between the two groups and investigated the predictive factors of postoperative IAA. Results: Sixteen patients developed postoperative IAA in the CA group, while no patients did in the SA group. The univariate analysis revealed that time from onset to surgery more than 3 days (p = 0.011), the preoperative CT finding of periappendiceal fluid (p = 0.003), abscess (p < 0.001), and free air (p <0.001), operation time more than 120 minutes (p = 0.023) and placement of a drainage tube (p <0.001) were significantly associated with the development of IAA. Multivariate analysis revealed that the preoperative CT finding of free air was independently associated with the development of IAA (p = 0.007, odds ratio = 5.427). Conclusions: IAA was developed predominantly in the patients with CA. Preoperative CT findings of free air was found to be an independent predictor for the development of IAA. Surgeons should be meticulous in managing the postoperative course of patients with this finding.

We describe an interesting case report about a patient with hemophilia A with severe chronic elbow arthropathy who underwent multiple surgical because of his condition. We collected all the clinical and imaging findings, and we compared the decision-making flow chart and the surgery performed with the most recent indications, treatments and complications reported in the literature. The aim of this case report is to show how usually the hemophilic patient even if young usually comes to our attention from the beginning with complex and advance musculoskeletal disease. Elbow hemophilic arthropathy is a complex disease and the management in these patients could be more difficult than others because of the higher risk of complications rate after all surgical procedures, for this reason it’s very important to treat these patients in hub centers with expertise in well-coordinated multidisciplinary teams. The path from diagnosis to surgical treatment of hemophilic elbow arthropathy can be a risky one, as it happened in this case.

Purpose: To determine whether 24-hour IOP monitoring can be a predictor for glaucoma progression and to analyze the inter-eye relationship of IOP, perfusion and progression parameters. Methods: We extracted data from manually drawn IOP curves with HIOP-Reader, a software suite we developed. The relationship between measured IOPs and mean ocular perfusion pressures (MOPP) to retinal nerve fiber layer (RNFL) thickness was analyzed. We determined the ROC curves for peak IOP (Tmax), average IOP (Tavg), IOP variation (IOPvar) and historical IOP cut-off levels to detect glaucoma progression (rate of RNFL loss). Bivariate analysis was conducted to check for various inter-eye relationships. Results: 217 eyes were included. The average IOP was 14.8±3.5 mmHg, with a 24-hour variation of 5.2±2.9 mmHg. 52% of eyes with RNFL data showed disease progression. There was no significant difference in Tmax, Tavg and IOPvar between progressors and non-progressors (all p>0.05). Except for Tavg and the temporal RNFL, there was no correlation between disease progression in any quadrant, Tmax, Tavg and IOPvar. 24-hour and outpatient IOP variables had poor sensitivities and specificities in detecting disease progression. The correlation of inter-eye parameters was moderate; correlation with disease progression was weak. Conclusion: In line with our previous study, IOP data obtained during a single visit (outpatient or inpatient monitoring) make for a poor diagnostic tool, no matter the method deployed. Glaucoma progression and perfusion pressure in left and right eyes correlated weakly to moderately with each other.

Finding an optimal combination of features and classifier is still an open problem in the development of automatic heartbeat classification systems, especially when applications that involve resource-constrained devices are considered. In this paper, a novel study of the selection of informative features and the use of a random forest classifier while following the recommendations of the Association for the Advancement of Medical Instrumentation (AAMI) and an inter-patient division of datasets is presented. Features were selected using a filter method based on the mutual information ranking criterion on the training set. Results showed that normalized R-R intervals and features relative to the width of the QRS complex are the most discriminative among those considered. The best results achieved on the MIT-BIH Arrhythmia Database were an overall accuracy of 96.14% and F1-scores of 97.97%, 73.06%, and 90.85% in the classification of normal beats, supraventricular ectopic beats, and ventricular ectopic beats respectively. In comparison with other state of the art approaches tested under similar constraints, this work represents one of the highest performances reported to date while relying on a very small feature vector.

Background: Forecasting nonlinear stochastic systems most often is quite difficult, without giving in to temptations to simply simplify models for the sake of permitting simple computations. Objective: Here, two basic algorithms, Adaptive Simulated Annealing (ASA) and path-integral codes PATHINT/PATHTREE (and their quantum generalizations qPATHINT/qPATHTREE) are offered to detail such systems. Method: ASA and PATHINT/PATHTREE have been effective to forecast properties in three disparate disciplines in neuroscience, financial markets, and combat analysis. Applications are described for COVID-19. Results: Results of detailed calculations have led to new results and insights not previously obtained. Conclusion: These 3 applications give strong support to a quite generic application of these tools to stochastic nonlinear systems.

Religious harmony performs a key role in preserving political and worldwide stability. Internationally it's far crucial to stay in a non-violent and harmonious environment, mainly in a society composed of believers of various races and religions. Relations among religions are normal. Failure to hold religious harmony can plunge society into battle and chaos. Therefore, the cause of this newsletter is to record in element the elements that affect the sustainable harmony among multi-religious societies. The record additionally emphasized that elements including acceptance, knowledge, cooperation, fairness, and justice are crucial elements in preserving religious harmony. Therefore, this paper pursuits to shape a solid idea of multi-sectarian harmony in society. It must additionally contribute to the improvement of a multi-religious society. Try to hold and construct a sturdy dating among them. Religious harmony is vital to make sure solidarity and team spirit amongst believers of more than one religion. A multi-religious society is a network with one-of-a-kind religions, including Islam, Buddhism, Hinduism, Christianity, etc. To stay in a non-violent and harmonious society, it's far very crucial to just accept believers from different religions in a selected network. From the angle of Islam, Islam is a faith that accepts the range of religions on this international however denies that every one religion is proper. So is the case in almost all religions. Religious pluralism may be described because of the range of religions on this international; however, withinside the idea of religious pluralism, it could be described because of the perception that every religion on this international is absolute truths. Pluralists trust that every one religion withinside the international is actual and have to be respected. It could be very crucial to recognize that everyone's proper statements are legitimate and deserve the same appreciation. This handiest method that fans of one religion have to be given different reality statements, including Muslims, Jews, Hindus, and others. However, from the angle of Islam, Islam accepts more than one religion however does now no longer understand that every one religion is proper. Recognizing the origins of various religions in a multi-religious society is the important thing to making sure harmony and solidarity withinside the international. Recognizing that religious range in a multi-religious society is a crucial component in preserving social harmony. For example, Muslims who cost the lifestyles of different religious groups (including Buddhists, Hindus, and Christians) can enhance inter-religious members of the society and deal with them kindly. Therefore, the popularity of the lifestyles of the religious range must be visible as a resounding component for a selected network. Everyone residing in a multi-religious society has to recognize and be given religious freedom. One must accept and appreciate the beliefs of different religions. Respect for the lifestyles of the religious range additionally contributes to political and countrywide stability. Respect also can enhance interreligious members of the society via way of means of acknowledging the lifestyles of various religious groups. Mutual appreciation, cooperation, tolerance, knowledge, and kindness are crucial elements in residing in a multi-ethnic and religious society. To hold a harmonious society, all multi-religious believers must have the proper and freedom to exercise their faith. It must now no longer be abandoned (Abdullah et al., 2016). Islam has usually emphasized the idea of justice (alAdl). All divine religions are of belief of religious harmony. By studying different religions, it is very clear that all religions are of the view to respect other religions and followers of different beliefs.

The digital representation of various signals allows, at the subsequent stages of their transmission, to apply correction codes that provide protection against possible errors arising from the action of interference in the communication channel. At the same time, it is important that, with the required correcting ability, these codes have the maximum possible speed. The article presents the results of calculations for linear codes, showing their really achievable limiting capabilities.

This study investigates the long-term stability of the Suomi National Polar-orbiting Partnership (S-NPP) Visible Infrared Imaging Radiometer Suite (VIIRS) moderate-resolution Thermal Emissive Bands (M TEBs; M12 – M16) covering a period from February 2012 to August 2020. It also assesses inter-sensor consistency of the VIIRS M TEBs among three satellites-S-NPP, NOAA-20, and NOAA-21 over eight months spanning from March 18 to November 30, 2023. The field of interesting is limited to the ocean surface between 60°S and 60°N, specifically under clear-sky conditions. Taking radiative transfer modeling (RTM) as the transfer reference, we employed the Community Radiative Transfer Model (CRTM) to simulate VIIRS TEB brightness temperature (BTs), incorporating European Centre for Medium-range Weather Forecasts (ECMWF) reanalysis data as inputs. Our results reveal two key findings. Firstly, the reprocessed S-NPP VIIRS TEBs exhibit a robust long-term stability, as demonstrated through analyses of the observation minus background BT differences (O-B ∆BTs) between VIIRS measurements (O) and CRTM simulations (B). The drifts of the O-B BT differences are consistently less than 0.105 K/Decade across all S-NPP VIIRS M TEB bands. Notably, observations from VIIRS M14 and M16 stand out with drifts well within 0.04 K/Decade, reinforcing their exceptional reliability for climate change studies. Secondly, excellent inter-sensor consistency among these three VIIRS instruments is confirmed through the double-difference analysis method (O-O). This method relies on the O-B BT differences obtained from daily data. The mean inter-VIIRS O-O BT differences remain within 0.08 K for all M TEBs, except for M13. Even in the case of M13, the O-O BT differences between NOAA-21 and NOAA-20/S-NPP have values of 0.312 K and 0.234 K, respectively, which are comparable to the 0.2 K difference between some TEBs among VIIRS and MODIS. These disparities are primarily attributed to the significant differences in the Spectral Response Function (SRF) of NOAA-21 compared to NOAA-20 and S-NPP. Our study confirms the RTM-based TEB quality evaluation method’s versatility and effectiveness in assessing long-term sensor stability and inter-sensor consistency. The double-difference approach effectively mitigates uncertainties and biases inherent to CRTM simulations, establishing itself a robust mechanism for assessing inter-sensor consistency. In addition, we’ve observed that, except for M13, M12 always exhibits larger spatial variations of O-O BT differences with greater uncertainties compared to the other M TEBs. The influence of solar contribution through sea surface reflection on the Top of Atmosphere (TOA) radiance measurements during daytime in M12 should not be underestimated.

This study explores the crucial roles of energy literacy, transition, and justice in addressing the global climate crisis. Through a systematic bibliometric survey and thematic analysis of existing literature, we identify a scarcity in research (<0.1%, n = 17,773) concurrently integrating the three crucial terms: energy literacy; energy transition; and energy justice. This study emphasizes the importance of energy literacy in empowering societies to make informed decisions, which is essential for facilitating equitable energy transitions and achieving sustainability goals. We delve into the interconnections between energy literacy and energy justice, proposing the integration of these concepts into educational systems, including social media platforms to foster an understanding of energy systems, their environmental impacts, and socio-economic implications. Emphasizing the strategic use of social media, the study also introduces the ‘COMPEL Justice’ framework—Communities Prepared for Energy Literacy and Justice—which aims to enhance public engagement and participation in energy transition initiatives. By analyzing publications from various academic and governmental sources, we provide insights into the challenges and opportunities that lie in promoting energy literacy and justice, particularly in the context of global efforts to mitigate climate change and enhance energy equity. Finally, exemplary application and implications associated with the adoption of the proposed framework within the context of oil-producing regions (e.g., Louisiana in the United States) are presented.

With the rapid development of smart phones, tablets and their operative systems, many positioning enabled sensors have been built into these devices. Users can now accurately fix their location according to the function of GPS receivers. For indoor environments, as in the case we are studying, WiFi based positioning is preferred to GPS due to the attenuation or obstruction of signals. This paper deals with the automatic classification of customers in a Sports Shop Center on the basis of their movements around the shop's premises. To achieve this goal, we start by collecting (x,y) coordinates from customers while they visit the store. Consequently, any costumer's path through the shop is formed by a list of coordinates, obtained with a frequency of one measurement per minute. Then, a guess about the full trajectory is constructed and a number of parameters about these trajectories is calculated before performing an Unsupervised Learning Clustering Process. As a result, we can identify several types of customers, and the dynamics of their behavior inside the shop. This information is of great value to the company, to be used both in the long term and also in short periods of time, monitoring the current state of the shop at any moment, identifying different types of situation appearing during restricted periods, or predicting customer flow conditions

A graph based path planning method consisting of off-line part and on-line part for multi-UAV system in windy condition is proposed. In the off-line part, the task area is divided into grids. When two nodes is close enough, they are connected and weighted by the cost, obtained by solving an optimization problem based on difference method, between them. In order to ensure the accuracy of the difference method, the adjacent radius is set to be small enough. In order to ensure the generated paths close to analytical solution, the grid size is set to be much smaller than the adjacent radius. The shortest path algorithm is used to update the adjacent matrix and path matrix. In the on-line part, the target position assignment and optimal velocity can be obtained by accessing the adjacent matrix and path matrix. At the end of this paper, some numerical examples are taken to illustrate the validity of our method and the influence of the parameters.

The article delves into the intricate phase transitions of 1-Octadecanol and n-Nonadecane within a binary system, unveiling dynamic structural changes under varying conditions. Through Fouri-er-transform infrared (FTIR) analysis, specific molecular vibrations were identified, shedding light on the molecular composition and interactions. The study highlights the challenges in detecting subtle phase transitions and emphasizes the individuality of molecular behaviours in closely related compounds. The findings underscore the complexity of phase transitions in binary systems and advocate for a nuanced approach to studying molecular structures and behaviours. Addi-tionally, the research contributes valuable insights into the molecular dynamics of Organic Polymer Functional Adsorption Materials, offering implications for synthetic waxy layers in plant epidermis.

EMG analysis is becoming increasingly important in many research and clinical applications, including muscle fatigue detection, control of robotic mechanisms and prostheses, clinical diagnosis of neuromuscular diseases and quantification of force. However, electromyographic signals can be contaminated by various types of noise, interference and artifacts, which can lead to misinterpretation of the data acquired using this method. Even assuming best practices, the collected signal may still be altered by such contaminants. The aim of this paper is to review methods employed to reduce contamination of single channel EMG signals. This review is limited to methods performed directly on the measured EMG signal and those that allow total reconstruction of the EMG signal. Subtraction methods used in the time domain, denoising methods performed after signal decomposition and hybrid methods are assessed. It is defended that individual methods may be more or less suitable for a particular application depending on contaminant(s) present in the signal and on the specific requirements of the application.

The influence of the film thickness and the substrate’s refractive index on the surface mode at the superstrate is an important study step that may help clearing some of the misunderstandings surrounding their propagation mechanism. A single sub-wavelength slit perforating a thin metallic film is among the simplest nanostructure capable of launching Surface Plasmon Polaritons on its surrounding surface when excited by an incident field. Here, the impact of the substrate and the film thickness on surface waves is investigated. When the thickness of the film is comparable to its skin depth, SPP waves from the substrate penetrate the film and emerge from the superstrate, creating a superposition of two SPP waves, that leads to a beat interference envelope with well-defined loci which are the function of both the drive frequency and the dielectric constant of the substrate/superstrate. As the film thickness is reduced to the SPP’s penetration depth, surface waves from optically denser dielectric/metal interface would dominate, leading to volume plasmons that propagate inside the film at optical frequencies. Interference of periodic volume charge density with the incident field over the film creates charge bundles that are periodic in space and time.

This paper presents the design and measurement of an IEEE 802.11ad standard compatible RF transceiver for 60GHz wireless communication system. In addition to the traditional half-duplex (HD) mode, this work supports full-duplex (FD) operation to deliver better channel utilization and faster response time for the system. The isolation between the transmitter and receiver from the architecture design to system integration for FD operation has been fully considered. A digital self-interference cancellation (DSIC) is implemented in MATLAB to verify the FD performance. The super-heterodyne architecture with an intermediate frequency (IF) of 12GHz is designed to suppress the image frequencies without using extra filters. A flexible phase-locked loop (PLL) synthesizer provides a local oscillator (LO) frequency with a 2kHz resolution. Other than the time division duplex (TDD) mode used in the conventional 60GHz system, a wide bandwidth baseband digital variable gain amplifier (DVGA) with a 3dB bandwidth of more than 4GHz also supports frequency division duplex (FDD) operation. The transceiver chip is fabricated in Tower Jazz 0.18µm SiGe BiCMOS process. With on-board antenna, the transceiver covers all four channels in 802.11ad standard with MCS-12 (7.04Gbps under 1.76GSym/s and 16-QAM) under 1.5m. In the proposed system design, the RF frontend based self-interference (SI) suppression from the local transmitter to receiver LNA is around 54dB. To achieve a practical FD application, the SI is further suppressed with the help of digital SI compensation. The measured power consumption for transmitter and receiver configuration is 194mW and 231mW, respectively, in HD mode and 398mW for FDD or FD operation mode.

The phenomenon of interference is a characteristic of all waves. This paper reviews the interference of classical waves and of matter waves in quantum mechanics. In quantum mechanics, there are two interference mechanisms between identical particles. One is that the de Broglie wavelengths of two interference waves are the same, which is called the equal wavelength interference mechanism. The other is that the wavelengths of interference waves can also be different, in which case there should be an exchange term in additional to the direction term in the wave function. There is a fixed phase difference between the two terms, which causes interference. This is called exchange effect interference mechanism. We propose an experiment, which is simpler to what has been done, to show the exchange effect interference. There is a special case where two interference waves can satisfy both the two mechanisms. We propose an experiment to discriminate that in this case which mechanism plays a role on earth.

This study investigates the applications of reconfigurable intelligent surfaces (RIS) in heterogeneous downlink networks (HetNet). Due to the network densification, the small cell base station (SBS) interferes with the macrocell users (MUE). In this paper, we utilize RIS to mitigate cross-tier interference in an HetNet via directional beamforming by adjusting the phase shift of the RIS. We consider an RIS-assisted HetNet consisting of multiple SBS nodes and MUEs that utilize both direct paths and reflected paths. Therefore, the aim of this study is to maximize the sum rate of all MUEs by jointly optimizing the transmit beamforming of the macrocell base station (MBS) and the phase shift of the RIS. An efficient RIS reflecting coefficients-based optimization (RCO) is proposed based on a successive convex approximation approach. Simulation results are provided to show the effectiveness of the proposed scheme in terms of its sum rate in comparison with the scheme HetNet without RIS and the scheme HetNet with RIS but with random phase shifts.

RNA interference (RNAi) using small interfering RNAs (siRNAs) is a powerful tool to target any protein of interest and is becoming more implementable for in vivo applications due to recent developments in RNA delivery systems. To exploit RNAi for cancer treatment, it is expedient to increase its selectivity by e.g. a prodrug approach to activate the siRNAs upon external triggering, e.g. by using light. Red light is especially well suitable for in vivo applications due to its low toxicity and higher tissue penetration. Known molecular (not nanoparticle based) red light activatable siRNA prodrugs rely on singlet oxygen (1O2) mediated chemistry. 1O2 is highly cytotoxic. Additionally one of the side products in the activation of the known siRNA prodrugs is anthraquinone, which is also toxic. We here report on an improved red light activatable siRNA prodrug, which do not require 1O2 for their activation. The 5’ terminus of its antisense strand is protected with an electron-rich azobenzene promoiety. It gets reduced and cleaved upon red light exposure in the presence of Sn(IV)(pyropheophorbide a)dichloride acting as a catalyst and ascorbate required as a bulk reducing agent producing active siRNAs.

During the launch and return of a spacecraft, the intense combustion of propellants generates strong electromagnetic radiation, which interferes with the operation of electronic equipment in the spacecraft. To improve the electromagnetic compatibility of electronic equipment in spacecraft, it is necessary to study the electromagnetic radiation characteristics of rocket fuel. An electromagnetic radiation measurement system based on antennas is designed to measure the electromagnetic radiation generated by rocket fuel, and the electromagnetic radiation characteristics are obtained through data analysis. The mechanism of the electromagnetic radiation generated by rocket fuel is comprehensively analysed through the spatial, time-domain, frequency-domain, and energy-domain characteristics. A characterization model is established to provide a reliable scheme for evaluating the influence of rocket fuel electromagnetic radiation on electronic equipment in spacecraft.

Our aim was to compare the inter-rater agreement of Transvaginal ultrasonography (TVS) with Magnetic Resonance Imaging (MRI) regarding diagnosing adenomyosis and for various predefined imaging features of adenomyosis in the same set of women. MRIs were assessed by four experienced radiologists and 2D TVS videoclips and 3D ultrasound volumes were assessed by five experienced sonographers. Each rater subjectively evaluated the presence or absence of adenomyosis, assessed various imaging. Fleiss kappa (κ) was used to reflect inter-rater agreement for categorical data and the Intraclass correlation coefficient (ICC) to reflect the reliability of quantitative data. Agreement between raters for diagnosing adenomyosis was higher for TVS than for MRI (κ =0.42 vs.0.28). MRI had a higher inter-rater agreement in assessing wall asymmetry irregular Junctional Zone (JZ) presence of myometrial cysts, while TVU had a better agreement for globular shape. MRI showed a moderate-good reliability for measuring the JZ (ICC=0.57-0.82). For TVS, JZ was unmeasurable in &gt; 50% of cases and the remaining cases had a low reliability (ICC=-0.31-0.08). We found that Inter-rater agreement for diagnosing adenomyosis was higher for TVS than for MRI, despite that MRI showed a higher inter-rater agreement in most specific features. Measurements of JZ in the coronal plane with 3D TVS were unreliable and thus unlikely to be useful for diagnosing adenomyosis.

Pancreatic beta cells secrete insulin in response to stimulation with glucose and other nutrients, and impaired insulin secretion plays a central role in development of diabetes mellitus. Pharmacological management of diabetes includes various antidiabetic drugs, including incretins. The incretin hormones, glucagon-like peptide-1 and gastric inhibitory polypeptide, potentiate glucose-stimulated insulin secretion by binding to G protein-coupled receptors, resulting in stimulation of adenylate cyclase and production of the secondary messenger cAMP, which exerts its intracellular effects through activation of protein kinase A or the guanine nucleotide exchange protein 2A. The mo-lecular mechanisms behind these two downstream signaling arms are still not fully elucidated and involve many steps in the stimulus-secretion coupling cascade, ranging from the proximal regula-tion of ion channel activity, to the central Ca2+ signal, and the most distal exocytosis. In addition to modifying intracellular coupling, the effect of cAMP on insulin secretion could also be at least partly explained by the impact on intercellular coupling. In this review, we systematically describe the possible roles of cAMP at these intra- and inter-cellular signaling nodes, keeping in mind the rele-vance for the whole organism and translation to humans.

Recently, inter-vehicle communication, which helps to avoid collision accidents (by driving safety support system) and facilitate self-driving (by dissemination of road and traffic information), has attracted much attention. In this paper, in order to efficiently collect road / traffic information in the request / response manner, first a basic method, Content-centric network (CCN) for Vehicular network (CV), is proposed, which applies CCN cache function to inter-vehicle communication. Content naming and routing, which take vehicle mobility into account, are investigated. On this basis, the CV method is extended (named as ECV) to avoid the cache miss problem caused by vehicle movement, and is further enhanced (named as ECV+) to more efficiently exploit cache buffer in vehicles, caching content according to a probability decided by channel usage rate. Extensive evaluations on network simulator Scenargie, with realistic open street map, confirm that the CV method and its extensions (ECV, ECV+) effectively reduce the average number of hops of data packets (by up to 47%, 63%, 83% respectively) and greatly improve the content acquisition success rate (by up to 356%, 444%, 689%, respectively), compared to the method without cache mechanism.

Background: Forecasting nonlinear stochastic systems most often is quite difficult, without giving in to temptations to simply simplify models for the sake of permitting simple computations. Objective: Here, two basic algorithms, Adaptive Simulated Annealing (ASA) and path-integral codes PATHINT/PATHTREE (and their quantum generalizations qPATHINT/qPATHTREE) are offered to detail such systems. Method: ASA and PATHINT/PATHTREE have been effective to forecast properties in three disparate disciplines in neuroscience, financial markets, and combat analysis. Applications are described for COVID-19. Results: Results of detailed calculations have led to new results and insights not previously obtained. Conclusion: These 3 applications give strong support to a quite generic application of these tools to stochastic nonlinear systems.

RNA interference (RNAi) is one of the main mechanisms for disease resistance and small RNA production in plants. The main proteins involved in RNAi include Dicer-like (DCL), RNA-dependent RNA polymerase (RDR), double-stranded RNA-binding (DRB), and Argonaute (AGO). Juglandaceae contains a variety of important woody plants, and walnuts are one of the four major woody plant groups and one of the four major dried fruits in the world. To clarify the evolution and functional differentiation of RNAi-related proteins in the walnut (Juglans regia) genome, this study integrated various web resources from gene family acquisition to structural analysis and transcriptome data to correlate walnuts and their congeners. The walnut genome has 5 DCL, 13 RDR, 15 DRB and 15 AGO genes, similar genes encoding conserved protein structural domains and conserved motifs with similar subcellular localization. Walnut AGO proteins are classified into three classes and seven subclasses. The DCL is divided into four categories, while RDR is mainly divided into four categories, and DRB can be divided into six categories. The exception is that the copy number of walnut RDR1 is 9, in which seven RDR1 are distributed in clusters on chromosome 16. Purifying selection drove the formation of walnut genes, but protein classes were subjected to varying degrees of purifying selection. Additionally, these results showed some similarity in other plants of the walnut family. Moreover, different RNAi-related genes of walnut produced abundant selective expression in response to different tissues and stresses. In this study, DCL, RDR, DRB and AGO gene families were identified and analysed in the genome of the walnut family for the first time and preliminarily examined the evolution, structure and expression characteristics of these families to provide a preliminary basis for the evolution of the walnut RNAi pathway and breeding research.

This article is a big picture of how electrical noise or conducted Electromagnetic Interference (EMI) is generated and mitigated in power converters. It gives an overview of what EMI in power converters is – from generation through to conduction and mitigation. It is meant to cover the complete subject as a summary so that the reader will have an outline of how to control conducted EMI by design (where possible) and how to mitigate by filtering. A clear distinction is made between Differential Mode (DM) and Common Mode (CM) EMI generation and mitigation. By using a boost converter as an example the trade-offs for DM noise control are discussed. It is shown how CM EMI is generated in a boost converter using the concept of the “Imbalance Difference Model” (IDM). Practical measurements for an in-line power filter is given showing the effect of the filter on the total EMI of a boost converter. Measurements for the CM current produced due to the imbalance difference for different values of the boost conductor are also shown. The main contribution of this study is linking CM noise generation to DM EMI. It is shown that CM noise is a direct consequence of DM noise (although circuit imbalance and coupling to a common ground also play a role). This paper will be useful to designers seeking the “bigger picture” of how EMI is generated in power converters and what can be done to mitigate the noise.

Plant pathogenic fungi are the largest group of disease-causing agents on crop plants and represent a persistent and significant threat to agriculture worldwide. Conventional approaches based on the use of pesticides raise social concern for the impact on the environment and human health and alternative control methods are urgently needed. The rapid improvement and extensive implementation of RNAi technology for various model and non-model organisms has provided the initial framework to adapt this post-transcriptional gene silencing technology for the management of fungal pathogens. In this review, we describe exogenous RNAi involved in plant pathogenic fungi and discuss small RNA production, formulation, and RNAi delivery methods. We explore some challenges with possible solutions. Furthermore, exogenous RNAi holds great potential for RNAi-mediated plant pathogenic fungal disease control.

Personalized recommendation is an important part of ecommerce platform. In the recommendation system, the neural network is used to enhance collaborative filtering to accurately capture user preferences, so as to obtain better recommendation performance. Traditional recommendation methods focused on the results of a single user behavior, ignoring the modeling of multiple interactive behaviors of users, such as click, add to cart and purchase. Although many studies had also focused on Multi-Behavior modeling, two important challenges remained. 1)Since multiple behavioral context information was ignored, it was still a challenge to identify the multimodal relationships of behaviors. 2) Surveillance signals were still sparse. In order to solve this problem, this paper proposes Two-path Multi-behavior Sequence Modeling(TP_MB). First, a two-path learning strategy is introduced to maximize the multiple interaction information of user items learned by the two paths, which effectively enhances the robustness of the model. Second, a multi-behavior dependent encoder is designed. Contextual information is obtained through behavior dependencies in the interaction of different user. In addition, three contrastive learning methods are designed, which not only obtain additional auxiliary supervision signals, but also alleviate the problem of sparse supervision signals. Extensive experiments on two real datasets demonstrate that our method outperforms state-of-the-art multi-behavior recommendation methods.

After developed the formulation of a "general relativity" in C⁴ [2], we proceed with the formulation of a Hamilton-Jacobi equation in C⁴. We argue that in this consideration, the usual problems of the ADM formalism, do not exist, due to the complex time as it exists in our consideration. Speci cally, we can derive a suitable dispersion relation in order to work with and nd a generalised super Hamiltonian

The use of antibiotics grown promoter has been banned, due led problems with drug residues in animal products and increased bacterial resistance. For several reasons there is a growing interest in the scientific community in immunoglobulin Y as antibiotic alternative and their oral administration in the polyclonal antibody (pAb) format, to maintain animal health and performance, do not require IgY purification for large-scale production, resulting in protein impurities and high concentration of biotin in the samples. The signal amplification through non-covalent interaction of biotin with streptavidin has been extensionally used by many laboratories for several diagnosis diseases and scientific research in enzyme-linked immunosorbent assay (ELISA). However, the riches sources of biotin as egg yolk, leading to high biotin concentrations in samples, harming the accuracy of diagnostic and proteins concentrations tests. This study aimed to evaluate the biotin influence on measurement of Immunoglobulin Y in egg yolk freeze dried samples from immunized laying hens by immunoassays using biotin-avidin/streptavidin. The IgY concentration changed down in immunoassays using biotin-avidin/streptavidin. The detection of IgY in yolk samples by ELISA using streptavidin–biotin binding as part of the assay methodology requires some technology to neutralize high concentration of biotin on sample or more steps beyond delipidation to isolate the target protein. Otherwise, an ELISA without the use of streptavidin-biotin binding would be more advisable to avoid biotin and targets protein relationship and prevent biotin interference on results.

The bonds of England and the UAE date back to over 220 years ago. This article explores the interference of Arabic prepositions in the English used in the United Arab Emirates (UAE), and their occurrences in light of gender and level of education, two important social variables related to linguistic behavior. To do so, participants will translate 20 sentences in Arabic into English as well as fill in 30 gaps in sentences in English with the missing prepositions. We will also experiment how musical intelligence may improve Emiratis’ performance regarding preposition. A study will be carried out to verify if participants from the experimental group, who will receive training on prepositions through music, obtains better results compared to the control group, who will receive training through a more traditional way (by listening to the instructor and repeating).

The diverse physical appearances and wide density range of polymer bead foams offer immense potential across various applications and future advancements. The multi-scale and multi-level structural features of bead foams involve many fundamental scientific topics. This review presents a comprehensive overview of recent progress in bead foams preparation and molding techniques. Initially, a comparative analysis is conducted among bead foam characteristics of distinct polymers, based on their unique properties. Subsequently, a summary and comparison of molding processes employed for fabricating bead foam parts are provided. Beyond traditional methods like steam-chest molding (SCM) and adhesive-assisted molding (AAM), emerging techniques like in-mold foaming and molding (IMFM) and microwave selective sintering (MSS) are highlighted. Lastly, the bonding mechanisms behind the diverse molding methods are discussed.

This study analyses 749 drawings of five female Bornean orang-utans (Pongo pygmaeus) at Tama Zoological Park in Japan. We searched for differences between individuals but also tried to identify possible temporal changes among the drawings of one individual, Molly, who drew almost 1,300 drawings from 2006 to 2016. An analysis of the drawings was carried out after collecting quantitative and qualitative variables. Our findings reveal evidence of differences in the drawing style of the five individuals as well as creative changes in Molly’s drawing style throughout her lifetime. Individuals differed in terms of the colours used, the space they filled but also the shapes (fan patterns, circles or loops) they drew. Molly drew less and less as she grew older, and we found a significant difference between drawings produced in winter, when orang-utans were kept inside and had less activity, and those produced during other seasons. Our results suggest that the drawing behaviour of these five orang-utans is not random and that differences among individuals might reflect differences of styles, states of mind but also motivation to draw.

This study investigated the magnitude and direction of inter-limb asymmetry in 21 professional female sepak takraw players across several task-specific tests. Five inter-limb asymmetry assessments were employed: unilateral countermovement jump (Uni-CMJ), bilateral countermovement jump (Bi-CMJ), single leg hop (SLH), triple hop test (THOP), and isokinetic concentric peak torque of the knee flexors and extensors at 60 deg/sec-1, 120 deg/sec-1 and 180 deg/sec-1 angular velocities. A “true” inter-limb asymmetry was only observed for Uni-CMJ jump height (16.62%) and THOP distance (6.09%). Kappa coefficients demonstrated fair agreement in the direction of asymmetry between the Uni-CMJ and Bi-CMJ tests for jump height (Kappa = 26.67), but only slight agreement for peak force (Kappa = 0.11), propulsive impulse (Kappa = -0.12) and eccentric impulse (Kappa = -0.14), respectively. Fair agreement was observed between the SLH and THOP (Kappa = 0.32). Slight to moderate agreement was found for concentric peak torque across angular velocities for the knee extensors (Kappa = 0.08 to 0.48) while fair to nearly perfect agreement was noted for the knee flexors (Kappa = 0.31 to 1). The Uni-CMJ and THOP are most sensitive to detect between-limb asymmetries in female sepak takraw players. However, given the inconsistency in asymmetry direction across tests, monitoring asymmetry direction is crucial for conditioning.

With the rise of powerful computational technologies, healthcare systems are going through a paradigm shift to the era of healthcare 5.0, also known as" smart healthcare". This new-age healthcare system not only enhances the life of patients but also aims to reduce healthcare costs significantly. People's health data collected through various means, including various Internet of Things (IoT) devices, is too sensitive to be regulated by particular organisations owing to increasing privacy and security threats. The sheer size of data makes it difficult for centralised bodies to regulate, due to which third-party involvement is introduced, which again poses threats to the privacy of the data holder. Motivated by the abovementioned gaps, we propose a decentralised approach using Ethereum blockchain technology and Oasis protocol. The patient-driven solution approach effectively solves the privacy problem by providing complete control of data to the owner. Along with this, byproducts such as fine-grained access control and on-chain data processing capabilities are also obtained.

The Collatz conjecture, a longstanding mathematical puzzle, posits that, regardless of the starting integer, iteratively applying a specific formula will eventually lead to the value 1. This paper introduces a novel approach to validate the Collatz conjecture by leveraging the binary representation of generated numbers. Each transition in the sequence is predetermined using the Collatz conjecture formula, yet the path of transitions is revealed to be intricate, involving alternating increases and decreases for each initial value. The study delves into the global flow of the sequence, investigating the behavior of the generated numbers as they progress toward the termination value of 1. The analysis utilizes the concept of probability to shed light on the complex dynamics of the Collatz conjecture. By incorporating probabilistic methods, this research aims to unravel the underlying patterns and tendencies that govern the convergence of the sequence. The findings contribute to a deeper understanding of the Collatz conjecture, offering insights into the inherent complexities of its trajectories. This work not only validates the conjecture through binary representation but also provides a probabilistic framework to elucidate the global flow of the sequence, enriching our comprehension of this enduring mathematical mystery.

Intelligent ship technology is currently an international research hotspot, and model predictive control is widely used in the path-tracking control of intelligent vehicles. To construct an intelligent ship anti-disturbance path-tracking control method, firstly, an environmental disturbance model was constructed with the actual meteorological data of the target sea area. Secondly, the Fossen ship equation of motion is linearized and discretized as the ship motion model. Thirdly, the expression of the prediction equation is derived from the ship motion model. Fourthly, the cost function is constructed by using the polar diameter and polar angle values of the ship. Fifth, the power function in the cost function is replaced with an exponential function to obtain an improved cost function. Sixthly, according to the Lyapunov theory and the MPC terminal constraint theory, the stability of the improved cost function is verified. Seventh, different test paths are set up, the environmental disturbance model is taken as the external disturbance, the ship motion model, the prediction equation, and the improved cost function are used to design the anti-disturbance path-tracking control algorithm according to the model prediction control idea for simulation experiments. Finally, different MATLAB simulation results show that the improved cost function can resist disturbance of the external wave, current, and wind, and effectively track the target path. Therefore, this study provides a reference for improving the navigation safety of ship path-tracking.

Type 2 Diabetes Mellitus is being increasingly associated with dysfunction of cognition. Dementia, including vascular dementia and Alzheimer’s disease, is being recognized as comorbidities of this metabolic disorder. The progressive hallmarks of this cognitive dysfunction include mild impairment of cognition and cognitive decline. Dementia and mild impairment of cognition appear in older patients primarily. Studies on risk factors, neuropathology, and brain imaging have provided important suggestions for mechanisms that lie behind the development of dementia. It is a significant challenge to understand the disease processes related to diabetes which affect the brain and lead to dementia development. The connection between Diabetes Mellitus and dysfunction of cognition has been observed in many human and animal studies that have noted mechanisms related to Diabetes Mellitus are possibly responsible for aggravating cognitive dysfunction. This article attempts to narrate the possible association between type 2 diabetes and Dementia, reviewing studies that have noted this association in vascular dementia and Alzheimer’s disease and helping to explain the potential mechanisms behind the disease process. The Google search for ‘Diabetes Mellitus and Dementia’ was carried out. Also, the search was done using ‘Diabetes Mellitus,’ ‘Vascular Dementia,’ ‘Alzheimer’s Disease.’ The literature search was done from Google Scholar, Pubmed, Embase, ScienceDirect, and MEDLINE. Keeping in mind the increasing rate of Diabetes Mellitus, it is important to establish the type 2 diabetes effect on the brain and diseases of neurodegeneration. This narrative review aims to build awareness regarding different types of dementia and their relationship with diabetes.

Yaw misalignment can make a wake steer, which is an effective method to increase the power of wind farms, but it also increases the fatigue load of the turbines. In this paper, the method of combining yaw misalignment and pitch control (CYMP) is proposed to investigate the potential to mitigate wake interference, the wind velocity distribution and turbulence distribution in the wake, as well as the power and load changes of the wind turbine are studied, focusing on power in-crement and fatigue damage reduction. Although some studies have found that the method of CYMP are beneficial to increase power generation and reduce fatigue loads, there are no papers that have made a detailed analysis of the effects of wake turbulence, wind speed distribution, power, especially fatigue damage under this control. Simulation tool FAST.Farm is used to model and analyze wind farms, obtain the variation details of wake and provide simulation data for calculating power and fatigue load. The pitch control brings bias to the CYMP optimization results was neglected, the case studies show that the method of CYMP can reduce the fatigue load by 10.29% and increase the total power by 1.7% compared with only wake steering. The Model Predictive Control collaborative method based on CYMP is proposed, which can increase power by more than 2% and reduce thrust by more than 4% under 10m/s turbulent wind.

In modern Commercial Off-The-Shelf (COTS) multicore systems, cores can produce several simultaneous memory requests. The processing of such requests over the memory controller negatively impacts the interference delay triggered by running parallel tasks on the platform. In this paper, we propose a software-based testing approach for analyzing memory interference delay, when cores are exposed to extensive read/write requests that access in parallel their Cache Coherent Interconnect. The hardware targeted in this work is the well-known LayerScape QorIQ LS2085A, which can be approached as a potential successor to the Freescale QorIQ P4080. The test analysis was conducted based on a bare-metal operating system that we developed to guarantee a deterministic execution environment at all time points. Our testing was accomplished using a set of carefully designed synthetic benchmarks as well as TACLeBench benchmarks.

In today’s digital economy data-based decisions have become very important to meet the ev-er-growing needs of customer engagement, retention, and satisfaction. Clickstream data is one such data that is being used to better understand, predict and engage with customers. Unfortu-nately, clickstream data for understanding customers has raised privacy and security concerns with many internet providers selling data for monetary benefits. This paper showcases a meth-odology that is developed based on experiential learning and using the latest cryptographic methods including differential privacy and graph analytics for predicting customer lifetime value (CLV) using clickstream data. Results obtained show that a user’s engagement can be pre-dicted within a relatively acceptable range after preserving privacy.

Facial expression recognition is crucial for understanding human emotions and nonverbal communication. With the growing prevalence of facial recognition technology and its various applications, accurate and efficient facial expression recognition has become a significant research area. However, most previous methods have focused on designing unique deep-learning architectures while overlooking the loss function. This study presents a new loss function that allows simultaneous consideration of inter- and intra-class variations to be applied to CNN architecture for facial expression recognition. More concretely, this loss function reduces the intra-class variations by minimizing the distances between the deep features and their corresponding class centers. It also increases the inter-class variations by maximizing the distances between deep features and their non-corresponding class centers, and the distances between different class centers. Numerical results from several benchmark facial expression databases, such as Cohn-Kanade Plus, Oulu-Casia, MMI, and FER2013, are provided to prove the capability of the proposed loss function compared with existing ones.

Camera malfunctions or loss of storage elements in imaging devices may lead to loss of important image information or random impulse noise interference. Low rank is one of the important prior information in image optimization processing. This paper uses different low-rank constraint models of the image matrices to recover the impulse interference satellite images. Firstly, an overview of image inpainting models based on nuclear norm, truncated nuclear norm, weighted nuclear norm, and matrix-factorization-based F-norm is presented, and corresponding optimiza-tion iterative algorithms are provided. Then, we conducted experiments under three types of pulse interference and provided visual and numerical results. Finally, it is concluded that the WSVT_ADMM method based on the weighted nuclear norm can obtain the best image inpainting results; The UV_ADMM method based on F norm of matrix factorization has the least computa-tion time and can be used for large-scale low-rank matrix computation; The WSVT_ADMM method based on weighted nuclear norm and the TSVT_ ADMM method based on truncated nuclear norms can significantly improve the repair effect compared to the nuclear norm-based methods such as SVT, SVP, and n_ADMM.

As a high-frequency carrier, the Terahertz (THz) wave is essential for achieving high-data-rate wireless transmission due to its ultra-wide bandwidth. Phase stabilization becomes crucial to enable phase-shift-based multilevel modulation for high-speed data transmission. We developed a Mach-Zehnder interferometric phase stabilization technique for photomixing, which has proved a promising method for phase-stable continuous THz-wave generation. However, this method faces inefficiencies in generating phase-modulated THz waves due to the impact of the phase modulator on the phase stabilization system. By photomixing, which is one of the promising methods for generating THz waves, the phase of the generated THz waves can be controlled in the optical domain so that the stability of the generated THz wave can be controlled by photonics technologies. Thus, we have devised a new phase stabilization approach using backward-directional lightwave, which is overlapped with the THz wave generation system. This study presents a conceptual and experimental framework for stabilizing the phase differences of optical carrier signals. We compare the optical domain and transmission performances between forward-directional and backward-directional phase stabilization methods. Remarkably, our results demonstrate error-free transmission at a modulation frequency of 3 Gbit/s and higher.

Pump Sizing is the process of dimensional matching an impeller and stator to provide a satisfactory performance test result and good service life during the operation of progressive cavity pumps. In this process, historical data analysis and dimensional monitoring are done manually, consuming a large amount of man-hours and requiring a deep knowledge of progressive cavity pump behavior. This work presents the use of complex networks in the construction of a prototype to recommend interference during the Pump Sizing process in a Progressive Cavity Pump. For this, data from different expert applications were used in addition to individual control Excel spreadsheets to build the database used in the prototype. From the pre-processed data, complex network techniques and the Betweenness Centrality metric were used to calculate the degree of importance of each order confirmation, as well as to calculate the dimensionality of the rotors. The model was evaluated using the mean squared error (MSE), obtaining a MSE of 0.28 for the cases where there were recommendations for order confirmations. Based on the results obtained, it was realized that there is a similarity with the dimensional defined by design engineers during the Pump Sizing process.

Climate changes caused by anthropogenic actions can directly and indirectly affect living beings, including parasites and their hosts. Changes such as water temperature, pH, distribution of nutrients in the aquatic environment are some examples that can interfere with the fish community, whether in open water or in production systems. In this review, we will show how climate change can affect the adaptation of hosts and parasites in the aquatic environment and how these parasites can be used for environmental monitoring.

The Performance Assessment for California Teachers (PACT) is a high stakes summative assessment that was designed to measure pre-service teacher readiness. We examined the inter-rater reliability (IRR) of trained PACT evaluators who rated 19 candidates. As measured by Cohen’s weighted kappa, the overall IRR estimate was .17 (poor strength of agreement). IRR estimates ranged from -.29 (worse than expected by chance) to .54 (moderate strength of agreement); all were below the standard of .70 for consensus agreement. Follow up interviews of 10 evaluators revealed possible reasons we observed low IRR, such as departures from established PACT scoring protocol, and lack of, or inconsistent, use of a scoring aid document. Evaluators reported difficulties scoring the materials that candidates submitted, particularly the use of Academic Language. Cognitive Task Analysis (CTA) is suggested as a method to improve IRR in the PACT and other teacher performance assessments such as the edTPA.

To keep the global navigation satellite system functional during extreme conditions, it is a trend to employ autonomous navigation technology with inter-satellite link. As in the newly built BeiDou system (BDS-3) equipped with Ka-band inter-satellite links, every individual satellite has the ability of communicating and measuring distances among each other. The system also has less dependence on the ground stations and improved navigation performance. Because of the huge amount of measurement data, centralized data processing algorithm for orbit determination is suggested to be replaced by a distributed one in which each satellite in the constellation is required to finish a partial computation task. In current paper, the balanced extended Kalman filter algorithm for distributed orbit determination is proposed and compared with whole-constellation centralized extended Kalman filter, iterative cascade extended Kalman filter, and increasing measurement covariance extended Kalman filter. The proposed method demands a lower computation power however yields results with a relatively good accuracy.

We investigate the stationary and dynamic properties of the celebrated Nosé-Hoover dynamics of many-body interacting Hamiltonian systems, with an emphasis on the effect of inter-particle interactions. To this end, we consider a model system with both short- and long-range interactions. The Nosé-Hoover dynamics aims to generate the canonical equilibrium distribution of a system at a desired temperature by employing a set of time-reversible, deterministic equations of motion. A signature of canonical equilibrium is a single-particle momentum distribution that is Gaussian. We find that the equilibrium properties of the system within the Nosé-Hoover dynamics coincides with that within the canonical ensemble. Moreover, starting from out-of-equilibrium initial conditions, the average kinetic energy of the system relaxes to its target value over a size-independent timescale. However, quite surprisingly, our results indicate that under the same conditions and with only long-range interactions present in the system, the momentum distribution relaxes to its Gaussian form in equilibrium over a scale that diverges with the system size. On adding short-range interactions, the relaxation is found to occur over a timescale that has a much weaker dependence on system size. This system-size dependence of the timescale vanishes when only short-range interactions are present in the system. An implication of such an ultra-slow relaxation when only long-range interactions are present in the system is that macroscopic observables other than the average kinetic energy when estimated in the Nosé-Hoover dynamics may take an unusually long time to relax to its canonical equilibrium value. Our work underlines the crucial role that interactions play in deciding the equivalence between Nosé-Hoover and canonical equilibrium.

Manufacturing environments, characterized by rapid, unpredictable changes, uncertainties, risks, and uncontrollable fluctuations, pose significant challenges to minimizing disruptions in processes. This study introduces an innovative approach that prioritizes curbing risk propagation among processes to enhance robustness. It emphasizes the integration of engineering management principles and modular design within manufacturing. Adopting a system engineering perspective, all manufacturing process activities are viewed as interrelated components within a unified system. By employing Axiomatic Design (AD) theory and the Design Structure Matrix (DSM) method, manufacturing process architecture is modularized, yielding heightened robustness. The proposed mathematical model equips engineering and manufacturing managers with a potent tool for designing robust processes while adeptly managing system complexity. The study's outcomes underscore a substantial enhancement in modularization, leading to elevated overall robustness in manufacturing processes. To validate the methodology, the architectural design of manufacturing processes is examined in a real-case scenario, specifically the Barez Industrial Group in Iran. This verification substantiates the 'manufacturing processes' of the case, presenting an optimally modularized architecture. The results affirm the proposed approach's efficacy, demonstrating improved modularization that contributes to bolstered robustness in manufacturing processes.

The constant ħ is elevated to a dynamical field, coupling to other fields, and itself, through the Lagrangian density derivative terms. The spatial and temporal dependence of ħ falls directly out of the field equations themselves. Three solutions are found: a free field with a tadpole term; a standing-wave non-propagating mode; a non-oscillating non-propagating mode. The first two could be quantized. The third corresponds to a zero-momentum classical field that naturally decays spatially to a constant with no ad-hoc terms added to the Lagrangian. An attempt is made to calibrate the constants in the third solution based on experimental data. The three fields are referred to as actons. It is tentatively concluded that the acton origin coincides with a massive body, or point of infinite density, though is not mass dependent. An expression for the positional dependence of Planck’s constant is derived from a field theory in this work that matches in functional form that of one derived from considerations of Local Position Invariance violation in GR in another paper by this author. Astrophysical and Cosmological interpretations are provided. A derivation is shown for how the integrand in the path integral exponent becomes Lc/ħ(r), where Lc is the classical action. The path that makes stationary the integral in the exponent is termed the “dominant” path, and deviates from the classical path systematically due to the position dependence of ħ. The meaning of variable ħ is seen to be related to the rate of time passage along each path increment. The changes resulting in the Euler-Lagrange equation, Newton’s first and second laws, Newtonian gravity, Friedmann equation with a Cosmological Constant, and the impact on gravitational radiation for the dominant path are shown and discussed.

The purpose of this paper is to explore the extent to which traditional economic policies can be oriented by sound practices. It is becoming widely accepted that sustainable economic growth (and not only economic growth) is the final target of economic policies; but most economic policies are applied just looking to the short-run without taking in account the long-run perspective. Our aim will be to show how a sustainable economic policy-making would be possible, making compatible the stabilization of the economy in the short-run with a sustainable economic growth in the long-run. We confront the design of economic policies with the 17 goals of the 2030 Agenda. We argue that all sustainable development goals can be attained by the design and implementation of sustainable economic policies. Finally, to illustrate this point we will conduct a simulation exercise to show under which combinations of demand policies technological shocks would promote a path of sustainable growth. Our results will provide a reference framework for a sustainable economic policy-making.

As a fundamental optical approach to interferometry, Sagnac interference has been widely used for reflection manipulation, precision measurements, and spectral engineering in optical systems. Compared to other interferometry configurations, it offers attractive advantages by yielding a reduced system complexity without the need for phase control between different pathways, thus offering a high degree of stability against external disturbance and a low wavelength dependence. The advance of integration fabrication techniques has enabled chip-scale Sagnac interferometers with greatly reduced footprint and improved scalability compared to more conventional approaches implemented by spatial light or optical fiber devices. This facilitates a variety of integrated photonic devices with bidirectional light propagation, showing new features and capabilities compared to unidirectional-light-propagation devices such as Mach-Zehnder interferometers (MZIs) and ring resonators (RRs). Here, we present our latest results for functional integrated photonic devices based on Sagnac interference. We outline the theory of integrated Sagnac interference devices with comparisons to other integrated photonic building blocks such as MZIs, RRs, photonic crystal cavities, and Bragg gratings. We present our latest results for Sagnac interference devices realized in integrated photonic chips, including reflection mirrors, optical gyroscopes, basic filters, wavelength (de)interleavers, and optical analogues of quantum physics.

With the rapid population growth, there is an urgent need for innovative crop improvement approaches to meet the increasing demand for food. Classical crop improvement approaches involve, however, a backbreaking process that cannot equipoise with increasing crop demand. RNA based approaches i.e. RNAi-mediated gene regulation and site-specific nuclease based CRISPR/Cas9 system for gene editing has made advances in the efficient targeted modification in many crops for the higher yield and resistance to diseases and different stresses. In functional genomics, RNA interference (RNAi) is a propitious gene regulatory approach that plays a significant role in crop improvement by permitting down-regulation of gene expression by small molecules of interfering RNA without affecting the expression of other genes. Gene editing technologies viz. clustered regularly interspaced short palindromic repeat (CRISPR)/CRISPR-associated protein (CRISPR/Cas) have appeared prominently as a powerful tool for precise targeted modification of nearly all crops genome sequence to generate variation and accelerate breeding efforts. In this regard, the review highlights the diverse roles and applications of RNAi and CRISPR/Cas9 system as powerful technologies to improve agronomically important plants to enhance crop yields and increase tolerance to environmental stress (biotic or abiotic). Ultimately, these technologies can prove to be important in view of global food security and sustainable agriculture.

It is claimed that classical mechanics (CM) in terms of its equivalent Koopman-von Neumann formulation (KvN) is indeed a ’real’ quantum theory since the formalism of quantum mechanics (FQM) does not, nor need it, exclude it as a such. This claim is made manifest by suggesting a common structure of which both KvN and ordinary quantum mechanics (OQM) correspond to unitary representations of, although unitarily inequivalent such. It is shown that OQM is obtained by enforcing the extra physical condition of quantized energy levels, which by itself does not constitute the ’quantum mystery’. It is furthermore shown that KvN in a physically realizable sense contain the hallmark quantum behavior of quantum interference. It is hence concluded that both CM and OQM are subjected to the same foundational issues. As the central part of both KvN and OQM is the introduction of probabilities via FQM it is suggested that the foundational issues regarding FQM are less about FQM itself and more about the concept of probability.

A growing number of studies suggest that SARS-CoV-2 could interfere with homeostatic mechanisms in the lung but the implications of this possible interference have not been fully explored in the literature. In this work, we examine the consequences that can be drawn from this hypothesis according to currently available knowledge. We suggest that one such consequence is the potential disruption of normal ventilation and perfusion of lung regions that may be distant from the infection sites. Loss of ventilation might result in local alveolar hypoxia and contribute to hypoxemia, which in turn could trigger homeostatic responses that enhance blood oxygenation by redistributing pulmonary blood circulation. Sudden changes in perfusion might then lead to the development of hydrostatic edema and eventually to vascular remodeling and inflammation. Therefore, the immune response might not be the only source of the substantial inflammation observed in lung tissues of patients with severe COVID-19, as is often assumed in the literature. The balance between the homeostatic and the immune reaction in each patient could account for the observed heterogeneity of the clinical manifestations of COVID-19.

The potential effect of implementing environmental regulations on economic growth is a controversial issue for a long time. As portrayed by Porter hypothesis, environmental regulations may impact on economic growth by reconstructing the economic structure. A number of previous literature proved the connections between the above three parties. With the intention of exploring the nature of this mechanism, it is important to understand the internal inter-relation of the three parties, requiring data from a large economy experiencing the transition in economic structure. By constructing a panel containing data from 30 Chinese provinces over 10 years (2008-2019), this paper investigate the dynamic inter-relation of the three parties by introducing PVAR model with Granger Test. Results reveal that environmental regulations give a “U” shaped impact to economic growth. In return, economic growth promotes the development of economy with a weakening strength. In addition, results also support the hypothesis that economic structure is the intermediate of economic growth and environmental regulations. There is a rooftop for the effect of economic structure to environmental regulations. The rooftop may signify the best optimization of primary structure.

Identifying dust aerosols from passive satellite images is of great interest for many applications. In this study, we developed 5 different machine-learning (ML) and deep-learning (DL) based algorithms, including Logistic Regression, K Nearest Neighbor, Random Forest (RF), Feed Forward Neural Network (FFNN), and Convolutional Neural Network (CNN), to identify dust aerosols in the daytime satellite images from the Visible Infrared Imaging Radiometer Suite (VIIRS) under cloud-free conditions on a global scale. In order to train the ML and DL algorithms, we collocated the state-of-the-art dust detection product from the Cloud-Aerosol Lidar with Orthogonal Polarization (CALIOP) with the VIIRS observations along the CALIOP track. The 16 VIIRS M-band observations with the center wavelength ranging from deep blue to thermal infrared, together with solar-viewing geometries and pixel time and locations, are used as the predictor variables. Four different sets of training input data are constructed based on different combinations of VIIRS pixel and predictor variables. The validation and comparison results based on the collocated CALIOP data indicates that the FFNN method based on all available predictor variables is the best performing one among all methods. It has an averaged dust detection accuracy of about 81 %, 89 % and 85 % over land, ocean and whole globe, respectively, compared with collocated CALIOP. When applied to off-track VIIRS pixels, the FFNN method retrieves geographical distributions of dust that are in good agreement with on-track results as well as CALIOP statistics. For further evaluation, we compared our results based on the ML and DL algorithms to NOAA’s Aerosol Detection Product (ADP) , which is a product that classifies dust, smoke and ash using physical-based methods. The comparison reveals both similarity and differences. Overall, this study demonstrates the great potential of ML and DL methods for dust detection and proves that these methods can be trained on the CALIOP track and then applied to the whole granule of VIIRS granule.

NASA’s ICESat-2space-borne photon-counting lidar mission is providing global elevation measurements that will provide significant benefits to a variety of bio-geoscience research applications. Given the novelty of elevation and the derived data products from the ICESat-2 mission, the research community needs software tools that can facilitate photon-level analyses to support product validation and development new analysis methods. Here, we describe PhotonLabeler, a free graphic user interface (GUI) for manual labeling and visualization of ICESat-2 Geolocated Photon data (ATL03). Developed in MATLAB, the GUI facilitates the reading and display of ATL03 Hierarchical Data Format (HDF) files, the manual labeling of individual photons into target classes of choice using a number of point selections tools and enables eventual saving of labeled data in ASCII format. Other capabilities include saving and loading of labeling sessions to manage labeling tasks over time. We expect labeled data generated using the application to serve two main purposes. First, serve as ground truth for validating various products from ICESat-2 mission, especially for study sites around the world that do not have existing reference datasets such as airborne lidar. Second, serve as training and validation data in the development of new algorithms for generating various ICESat-2 data products. We demonstrate the first use case through a validation case study for the land and vegetation product (ATL08), which provides canopy and terrain height estimates, over two sites. For the first site, located in northwestern Zambia, we used ICESat-2 ATL03 data acquired at night and for our second site in Texas, US, we used ATL03 data acquired during the day. The PhotonLabeler application is freely available as a compiled MATLAB binary to enable free access and utilization by interested researchers.

The amorphous Fe77Cu1Si13B9 ribbons were treated with pulsed laser interference heating (PLIH). It was confirmed here that the use of the laser heating process allowed for obtaining two-dimensional crystallised micro-areas, periodically distributed (at a distance of 17µm) on the surface of the amorphous ribbons. The correlation between structural changes (SEM, TEM, HRTEM) and the distribution of magnetic field lines of heated amorphous Fe77Cu1Si13B9 (FeCuSiB) ribbons is presented. Particular attention is paid to structure changes in micro-areas where, by controlling the laser interference heating process, partial crystallisation of amorphous alloys and the formation of clusters or single nanocrystallites (α-Fe(Si)) embedded in an amorphous matrix are given. The addition of copper to the FeSiB alloy promoted inhibition of grain growth. Electron holography of micro-areas confirmed shifts of the magnetic field lines in the areas of nanocrystallites, the presence of which in the structure caused magnetisation of the surrounding amorphous matrix.

High-performance electromagnetic interference (EMI) shielding materials with ultralow density and environment friendly properties are greatly demanded to address electromagnetic radiation pollution. Herein, carbon nanotubes/polylactic acid (CNTs/PLA) materials with different CNTs contents, which exhibit characteristics of light weight, environmental protection and good chemical stability, are fabricated by 3D printing technology, where CNTs are evenly distributed and bind well with PLA. The performances of 3D printed CNTs/PLA composite are improved compared to pure 3D printed PLA composite, which include mechanical properties, conductive behaviors and electromagnetic interference (EMI) shielding. The EMI shielding effectiveness (SE) of CNTs/PLA composite could be improved when the contents of CNTs increase. When it reaches 15 wt%, the EMI SE of 3D printed CNTs/PLA composite could get up to 47.1 dB, which shields 99.998% of electromagnetic energy. Meanwhile, the EMI shielding mechanism of 3D printed CNTs/PLA composite is mainly of absorption loss, and it generally accounted for more than 80% of the total shielding loss. These excellent comprehensive performances endow the 3D printed CNTs/PLA composite with great potential for use in industrial and aerospace area.

Radio Frequency Interference (RFI) detection and characterization play a critical role to in ensuring the security of all wireless communication networks. Advances in Machine Learning (ML) have led to the deployment of many robust techniques dealing with various types of RFI. To sidestep an unavoidable complicated feature extraction step in ML, this paper proposes an efficient end-to-end method using the latest advances in deep learning to extract the appropriate features of the RFI signal. Moreover, this study utilizes the benefits of transfer learning to determine both the type of received RFI signals and their modulation types. To this end, the scalogram of the received signals is used as the input of the pre-trained convolutional neural networks (CNN), followed by a fully-connected classifier. This study considers a digital video stream as the signal of interest (SoI), transmitted in a real-time satellite-to-ground communication using DVB-S2 standards. To create the RFI dataset, the SoI is combined with three well-known jammers namely, continuous-wave interference (CWI), multi- continuous-wave interference (MCWI), and chirp interference (CI). This study investigated four well-known pre-trained CNN architectures, namely, AlexNet, VGG-16, GoogleNet, and ResNet-18, for the feature extraction to recognize the visual RFI patterns directly from pixel images with minimal preprocessing. Moreover, the robustness of the proposed classifiers is evaluated by the data generated at different signal to noise ratios (SNR).

Cable interference in cable-driven mechanisms (CDM) is a major challenge in their applications. The wrench closure workspace (WCW) in a fully constrained mechanism may not be realized unless cable interference is considered. This paper classifies all possible types of cable interferences for planar cable-driven mechanisms and presents an analytical solution to find the boundaries of the constant-orientation interference region. It is shown that interference between cables starts and ends when one end of a cable coincides with another cable which can be thought as lying a point on a line segment. This geometrical view is developed and applied to provide a framework for the analysis of cable interference. By subtracting the interference space form WCW, the interference-free workspace is obtained in which the robot is able to operate.

One of the most common limits to gas sensor performance is the presence of unwanted interference fringes or etalons arising, for example, from multiple reflections between surfaces in the optical path. Additionally, since the amplitude and the frequency of these interference depend on the distance and alignment of the optical elements, they are affected by temperature changes and mechanical disturbances, giving rise to a drift of the signal. In this work, we present a novel semi-parametric algorithm which allows the extraction of a signal, like the spectroscopic absorption line of a gas molecule, from a background containing arbitrary disturbances, without having to make any assumption on the functional form of these disturbances. The algorithm is applied first to simulated data and then to oxygen absorption measurements in presence of strong fringes.To the best of the authors' knowledge, the algorithm enables an unprecedented accuracy particularly if the fringes have a free spectral range and amplitude comparable to those of the signal to be detected. The described method presents the advantage of being based purely on post processing, and to be of extremely straightforward implementation if the functional form of the Fourier transform of the signal is known. Therefore it has the potential to enable interference-immune absorption spectroscopy. Finally, its relevance goes beyond absorption spectroscopy for gas sensing since it can be applied to any kind of spectroscopic data.

This research aims to analyse the sustainability of retirement system and relevant optimal path to achieve sustainable post-retirement livings in Malaysia context. Focus of this study is put on Employees Provident Fund (EPF) which is mainly constituted by employees from private sector. EPF is a fully funded defined-contribution by both employees and employers. In this research, main variables used are contribution rate and retirement age based on relevant indexation of pension. For a sustainable retirement living, retirement benefits are expected to be in a maximisation function. Attempts to find sustainable retirement fund are via step-by-step mathematical calculation using formulas in Microsoft Excel and verification of the result with Excel Solver via Generalised Reduced Gradient (GRG) algorithm. Eventually, two-third retirement decision model is used to justify the sustainability of retirement fund other than justification using monthly household expenditure.

The paper presents models of path and control planning for parking, docking, and movement of autonomous vehicles at low speeds considering space constraints. Given the low speed of motion, and in order to test and approve the proposed algorithms, vehicle kinematic models are used. Recent works on the development of parking algorithms for autonomous vehicles are reviewed. Bicycle kinematic models for vehicle motion are considered for three basic types of vehicles: passenger car, long wheelbase truck, and articulated vehicles with and without steered semitrailer axes. Mathematical descriptions of systems of differential equations in matrix form and expressions for determining the linearization elements of nonlinear motion equations that increase the speed of finding the optimal solution are presented. Options are proposed for describing the interaction of vehicle overall dimensions with the space boundaries, within which a maneuver should be performed. An original algorithm that considers numerous constraints is developed for determining vehicle permissible positions within the closed boundaries of the parking area, which are directly used in the iterative process of searching for the optimal plan solution using nonlinear model predictive control (NMPC). The process of using NMPC to find the best trajectories and control laws while moving in a semi-limited space of constant curvature (turnabouts, roundabouts) are described. Simulation tests were used to validate the proposed models for both constrained and unconstrained conditions and the output (state-space) and control parameters' dependencies are shown. The proposed models represent an initial effort to model the movement of autonomous vehicles for parking and has the potential for other highway applications.

In this paper, we present a groundbreaking methodology in the realm of aspect-level sentiment analysis, which capitalizes on the advanced capabilities of graph-based neural networks. Our approach, distinguished as the Aspect Correlation Graph Network (ACGN), represents a significant departure from conventional models. These traditional models often analyze aspects in isolation, failing to capture the intricate web of sentiment relationships that may exist within a single sentence. ACGN, however, is designed to address this gap by employing a sophisticated bidirectional attention mechanism, integrated with positional encoding. This unique combination not only enhances the model's ability to focus on relevant parts of the sentence but also aids in constructing detailed, aspect-focused representations. These representations are particularly crucial for understanding the nuanced interplay of sentiments associated with different aspects. Central to our model's architecture is the incorporation of a graph convolutional network. This network serves as a pivotal component in mapping and analyzing the complex network of sentiment correlations that can exist among various aspects within sentences. Through this integration, ACGN is able to unearth and interpret the subtle and often overlooked sentiment dynamics that traditional models might miss. Our comprehensive evaluations of the Aspect Correlation Graph Network, conducted using the SemEval 2014 datasets, have yielded promising results. These findings demonstrate a clear and significant advancement over the capabilities of existing models. Particularly, the results underscore the critical importance and utility of recognizing and understanding the connections between sentiments of different aspects in text analysis. This insight opens new avenues in the field of sentiment analysis, suggesting a broader application potential of ACGN in various contexts where understanding nuanced sentiment relationships is key. Overall, our study not only introduces a novel approach in aspect-level sentiment analysis but also sets a new standard for future research in this area. By highlighting the integral role of inter-aspect sentiment connections, ACGN paves the way for more sophisticated and accurate sentiment analysis tools, capable of handling the complexities of natural language with greater finesse and precision.