In this paper, the technical aspects of a multi-lidar instrument, the long-range WindScanner system, will be presented accompanied by an overview of the results from several field campaigns. The long-range WindScanner system consists of three spatially separated coherent Doppler scanning lidars and a remote master computer that coordinates them. The lidars were carefully engineered to perform arbitrary and time controlled scanning trajectories. Their wireless coordination via the master computer allows achieving and maintaining lidars’ synchronization within ten milliseconds. As a whole, the long-range WindScanner system can measure an entire wind field by emitting and directing three laser beams to intersect, and then by moving the beam intersection over the points of interest. The long-range WindScanner system was developed to tackle the need for high-quality observations of wind fields from scales of modern wind turbine and wind farms. It has been in operation since 2013.

This paper presents the concept of applying incremental capacity analysis (ICA) on the OCV curve in the SoC space. The OCV curve can be obtained from any sequence of discharge or charge current or power pulse with a necessary rest period to allow the cell to reach a pseudo-OCV after each pulse. With a higher resolution (>100 pulses) in the full SoC window, an OCV vs SoC curve can be obtained with sufficient accuracy to perform an ICA on the obtained OCV curve. ICA as a diagnostic technique has commonly been applied on Li-ion cells with a constant charge and discharge at slow currents. However, a slow controlled constant current charge or discharge is normally not feasible and cannot be easily applied to a battery in an application. Here we revisit pulse-based ICA to supplement the conventional constant-current-based technique. Conventional ICA performed on ageing data with constant current is directly compared to ICA performed on a selection of higher resolution OCV curves. The main advantage of OCV-ICA is that it can be applied to most cells and systems without significant interruption of normal cell operation. OCV-ICA provides valuable insights into ageing mechanisms as well as detailed information on changes in internal resistance.

We extended our model of the S1 tubular segment to address the mechanisms by which SGLT1 interacts with lateral Na/K pumps and tight junctional complexes to generate isosmotic fluid reabsorption via tubular segment S3. The strategy applied allowed simulation of laboratory experiments. Reproducing known experimental results constrained the range of acceptable model outputs and contributed to minimizing the free parameter space. 1. In experimental conditions, published Na and K concentrations of proximal kidney cells were found to deviate substantially from their normal physiological levels. Analysis of the mechanisms involved suggested insufficient oxygen supply as the cause and indirectly, that a main function of the Na/H exchanger (NHE3) is to extrude protons stemming from mitochondrial energy metabolism. 2. The water path from the lumen to the peritubular space is through aquaporins on the cell membrane and claudin-2 at paracellular tight junctions, with a smaller additional contribution to water transport by the coupling of 1 glucose:2 Na:200 H2O in SGLT1. 3. A Na+-uptake component passed through paracellular junctions by solvent drag in Na- and water-permeable claudin-2, thus bypassing the Na/K-pump, in agreement with the findings of early studies. 4. Electrical cross talk between apical rheogenic SGLT1 and lateral rheogenic Na/K pumps results in tight coupling of luminal glucose uptake and transepithelial water flow. 5. Isosmotic transport is achieved by Na-mediated ion recirculation at the peritubular membrane.

We have successfully developed curcumin nanosuspension aimed for oral delivery. The main purpose is to improve bioavailability through enhancing its solubility. The nanoparticles were stabilized using various stabilizers including polyvinyl pyrrolidone (PVP), polyvinyl alcohol (PVA), sodium carboxymethylcellulose (Na-CMC), d-alpha tocopheryl polyethylene glycol 1000 succinate (TPGS), and sodium dodecyl sulfate (SDS). The average diameter of particles, microscopic appearance, and sedimentation of each preparation was observed and compared. Each stabilizer demonstrated different degree of inhibition of particle aggregation under electrolyte-containing simulated gastrointestinal (GIT) fluid. Non-ionic stabilizers (PVA, PVP, and TPGS) has shown to preserve the nanosuspension stability against electrolytes. In contrast, strong ionic surfactants such as SDS were found to be very sensitive to electrolytes. The results can provide useful information for the formulators to choose the most suitable stabilizers by considering the nature of stabilizers and physiological characteristics of target site of the drug.

Taiwan developing offshore wind power to promote green energy and self-electricity production. In this study, a Light Detection and Ranging (Lidar) was set up at Chang-Hua development zone one on the sea and 10km away from the seashore. At Lidar location, WRF (3.33km & 2km grid lengths) model and WAsP were used to simulate the wind speed at various elevations. Three days mean wind speed of simulated results were compared with Lidar data. From the four wind data sets, developed five different comparisons to find an error% and R-Squared values. Comparison between WAsP and Floating Lidar was shown good consistency. Lukang meteorological station 10 years wind observations at 5m height were used for wind farm energy predictions. The yearly variation of energy predictions of traditional and TGC wind farm layouts are compared under purely neutral and stable condition. The one-year cycle average surface heat flux over the Taiwan Strait is negative (-72.5 (W/m2) and 157.13 STD), which represents stable condition. At stable condition TGC (92.39%) and 600(92.44%), wind farms were shown higher efficiency. The Fuhai met mast wind data was used to estimate roughness length and power law exponent. The average roughness lengths are very small and unstable atmosphere.

Considering the high potential of hydrogen (H₂) as a clean energy carrier, the implementation of high performance and cost-effective biohydrogen (bioH₂) purification techniques is of vital importance, particularly in fuel cell applications. In this context, membrane technology is a potentially energy-saving solution to obtain high-quality biohydrogen. The most promising poly(ionic liquid) (PIL) - ionic liquid (IL) composite membranes previously studied by our group for CO₂/N₂ separation, containing pyrrolidinium-based PILs with fluorinated or cyano-functionalized anions, were chosen as starting point to explore the potential of PIL–IL membranes for CO₂/H₂ separation. The CO₂ and H₂ permeation properties at the typical conditions of biohydrogen production (T =308 K and 100 kPa of feed pressure) were measured and discussed. PIL–IL composites prepared with [C(CN)₃]^– anion showed higher CO₂/H₂ selectivities and H₂ diffusivities compared to those containing [NTf₂]^– anion. All the membranes revealed CO₂/H₂ separation performances above the upper bound for this specific separation, highlighting the composite incorporating 60 wt% of [C₂mim][C(CN)₃] IL.

The Atmospheric Dynamics Mission ADM-Aeolus was successfully launched in August 2018 by the European Space Agency (ESA). The Aeolus mission carried a single instrument, the first-ever Doppler Wind Lidar (DWL) in space, called Atmospheric LAser Doppler INstrument (ALADIN). Aeolus circled the Earth in a polar sun-synchronous orbit at about 320 km altitude with a repeat cycle of 7 days, providing vertical profiles of horizontal line-of-sight (HLOS) winds on a global scale. Exceeding scientific expectations, Aeolus, initially designed for a 3-year lifetime, provided global coverage of wind profiles for almost five years. In this long-term validation study, we assessed the accuracy of the Level 2B (L2B) Rayleigh-clear and Mie-cloudy wind products by collecting radiosonde data from three stations in the Brazilian Amazon: Cruzeiro do Sul (7.62° S, 72.67° W), Porto Velho (8.76° S, 63.91° W), and Rio Branco (10.00° S, 67.80° W). Statistical validation was conducted by comparing Aeolus L2B wind products and radiosonde data, launched daily at 12:00 UTC from October 2018 to March 2023. Considering all data collected during the mission period, Pearson’s coefficient (R) of 0.73 was observed in Rayleigh-clear and 0.85 in Mie-cloudy, revealing a strong correlation between Aeolus and radiosonde winds. No significant biases were detected, with values of -0.14 m/s for Rayleigh-clear and -0.40 m/s for Mie-cloud, fulfilling the mission requirement of having absolute biases below 0.7 m/s. However, when analyzed annually, in 2022, the bias for Rayleigh-clear was -0.95 m/s, exceeding the mission requirements.

This paper performs a comprehensive analysis of the wind energy potential of onshore regions in Greece with emphasis on quantifying the volume risk and the spatial covariance structure. Optimization techniques are employed to derive efficient wind capacity allocation plans (also known as generation portfolios) incorporating different yield aspirations. The generation profile of minimum variance and other optimal portfolios along the efficient frontier are subject to rigorous evaluation using a fusion of descriptive and statistical methods. In particular, principal component analysis is employed to estimate factor models and investigate the spatiotemporal properties of wind power generation, providing valuable insights into the persistence of volume risk. The overarching goal of the study is to employ a set of statistical and mathematical programming tools guiding investors, aggregators and policy makers in their selection of wind energy generating assets. The findings of this research challenge the effectiveness of current policies and industry practices, offering a new perspective on wind energy harvesting with a focus on the management of volume risk.

With the rapid development of wind power generations, the inertial response of wind turbines (WTs) are widely concerned recently, which is important for grid frequency dynamic and stability. This paper recognizes and understands the inertial response of type-3 and type-4 WTs from the view of equivalent internal voltage, in analogy with typical synchronous generators (SGs). Due to the dynamic of the equivalent inertial voltage different from SGs, the electromechanical inertia of WTs is completely hidden. The rapid power control loop and synchronization control loop is the main reasons that the WT's inertial response is disenabled. On the basis of the equivalent internal voltage's dynamic, the existing inertia control method for WTs are reviewed and summarized as three approaches from the view of WT's control, i.e. optimizing the power control or synchronization control or both. At last, the main challenges and issues of these inertia controls are attempted to explain and address.

Accurate power curve modelling is essential to continuously evaluate the performance of a wind turbine (WT). In this work, we characterize the wind power curves using SCADA data acquired at a frequency of 5 minutes in a wind farm (WF) consisting of 5 WTs. Regarding the non-parametric methods, we select artificial neural networks (ANNs) to make curve estimations. Given that, we have the curves provided by the manufacturer of the WTs given by some very precisely measured pair of wind speed and power points. We can evaluate the difference between the manufacturer characterization and the ones estimated with the data provided by the SCADA system. Before the estimation, we propose a method of filtering the anomalies based on the characteristics provided by the manufacturer. We use three-quarters of the available data for curve estimation and one-quarter for the test. One WT suffered a break in the test part, so we can check how the test estimates reflect this problem in its wind-power curve compared to the estimations obtained in the WTs that worked adequately.

Redox mediators comprising I–, Co3+, and Ti3C2Tx MXene were applied to dye-sensitized solar cells (DSCs). In the as-prepared DSCs (I-DSCs), wherein hole conduction occurred via the redox reaction of I−/I3− ions, the power conversion efficiency (PCE) was not altered by the addition of Ti3C2Tx MXene. The I-DSCs were exposed to light to produce Co2+/Co3+-based cells (Co-DSCs), wherein the holes were transferred via the redox reaction of Co2+/Co3+ ions. A PCE of 9.01% was achieved in a Co-DSC with Ti3C2Tx MXene (Ti3C2Tx-Co-DSC), which indicated an improvement from the PCE of a bare Co-DSC without Ti3C2Tx MXene (7.27%). It was also found that the presence of Ti3C2Tx MXene in the redox mediator increased the hole collection, dye regeneration, and electron injection efficiencies of the Ti3C2Tx-Co-DSC, leading to an improvement in both the short-circuit current and the PCE when compared with those of the bare Co-DSC without MXene.

This paper presents a system for identification of wind features, such as gusts and wind shear. These are of particular interest in the context of energy-efficient navigation of Small Unmanned Aerial Systems (UAS). The proposed system generates real-time wind vector estimates and a novel algorithm to generate wind field predictions. Estimations are based on the integration of an off-the-shelf navigation system and airspeed readings in a so-called direct approach. Wind predictions use atmospheric models to characterize the wind field with different statistical analyses. During the prediction stage, the system is able to incorporate, in a big-data approach, wind measurements from previous flights in order to enhance the approximations. Wind estimates are classified and fitted into a Weibull probability density function. A Genetic Algorithm (GA) is utilized to determine the shaping and scale parameters of the distribution, which are employed to determine the most probable wind speed at a certain position. The system uses this information to characterize a wind shear or a discrete gust and also utilizes a Gaussian Process regression to characterize continuous gusts. The knowledge of the wind features is crucial for computing energy-efficient trajectories with low cost and payload. Therefore, the system provides a solution that does not require any additional sensors. The system architecture presents a modular decentralized approach, in which the main parts of the system are separated in modules and the exchange of information is managed by a communication handler to enhance upgradeability and maintainability. Validation is done providing preliminary results of both simulations and Software-In-The-Loop testing. Telemetry data collected from real flights, performed in the Seville Metropolitan Area in Andalusia (Spain), was used for testing. Results show that wind estimation and predictions can be calculated at 1 Hz and a wind map can be updated at 0.4 Hz. Predictions show a convergence time with a 95% confidence interval of approximately 30 s.

(1)Background：To date, no studies have epidemiologically examined whether the concentration of particulate matter (PM) 2.5 and its ionic components is related to the prevalence of skin symptoms. Therefore, this study aimed to clarify this association in patients with allergic diseases. (2)Methods: From February 1 to May 31, 2020, we evaluated the daily prevalence of skin symptoms in outpatients with allergic diseases being treated at Fukuoka Hospital, Fukuoka, Japan, and measured the concentration of PM2.5 and its ionic components. （3）Results: Univariate analysis showed a statistically significant association between skin symptoms and the concentration of PM2.5 and the ionic components SO42-, NH4+, K+, and Mg2+, and multivariate analysis showed a statistically significant association between the daily prevalence of skin symptoms and the concentration of the ionic components SO42- or Mg2+. (4)Conclusions: Our findings indicate that the concentration of some PM2.5 ionic components may affect skin symptoms in patients with allergic diseases.

Two interesting compounds such as quaternary ammonium lignin(QAL) and 2-ethylhexyl phosphoric acid mono-2-ethylhexyl ester (P507) were synthesized as ionic liquids(QP-ILs) for the extraction of metal ions. The extraction behavior of Co(II) and Ni(II) from chloride solution was compared between QP-ILs and P507. The results showed that the extraction rates of Co(II) and Ni(II) in the two solutions varied with the extraction conditions, but QP-ILs has stronger extractability for cobalt than P507, while Ni is on the contrary. Under the same conditions, the Co/Ni separation performance(βCo/Ni) in QP-ILs is superior to that in p507. At pH4.0, 55℃, concentration of 20%, extraction time of 10 minutes, the βCo/Ni of QP-ILs reached to 2703, while that of P507 was only 164. In conclusion, QP-ILs was more efficient than P507 for separating Co from mixed solutions.

This paper designed a new type of generator, transgenerator, that integrates the wind turbine and flywheel into one system, aiming to make the flywheel distributed energy storage (FDES) more modular and scalable than the conventional FDES. The transgenerator is a three-member dual-mechanical-port (DMP) machine with two rotating members (inner and outer rotors) and one stationary member (stator). The transgenerator-flywheel system is introduced with the system configuration, transgenerator overview, flywheel operation principle and power management strategies, and control system. Simulations are performed in MATLAB/ Simulink to verify the system viability, including control system verification and the flywheel storage performance evaluation. Results show that the inner and outer rotors can be controlled independently with accurate and fast control response, and the grid-side control works properly. The flywheel performs well with considerable charging power and storage capacity.

Solid polymer electrolytes and composite polymer electrolytes serve as crucial components in all-solid-state energy storage devices. Structural batteries and supercapacitors present a promising alternative for electric vehicles, integrating structural functionality with energy storage capability. However, despite their potential, these applications are hampered by various challenges, particularly in the realm of developing new solid polymer electrolytes that require more investigations. In this study, novel solid polymer electrolytes and composite polymer electrolytes were synthesized using epoxy resin blends, ionic liquid, lithium salt, and alumina nanoparticles, and subsequently characterized. Among the formulations tested, the optimal system, designated as L70P30ILE40Li1MAl2 and containing 40 wt.% of ionic liquid and 5.7 wt.% of lithium salt, exhibited exceptional mechanical properties. It displayed a remarkable storage modulus of 1.2 GPa and reached ionic conductivities of 0.085 mS/cm at 60°C. Furthermore, a proof-of-concept supercapacitor was fabricated, demonstrating the practical application of the developed electrolyte system.

In the context of the Korean building structure standard KDS2022, wind loads can be readily calculated in terms of the along-wind, across-wind, and torsional components, based on a single wind direction. However, this approach falls short in accurately and safely evaluating the impact of winds from various directions. Therefore, in this study, we developed a Wind Load Calculation Program (WCP) capable of predicting wind loads with relative precision during the preliminary design phase. First, wind tunnel tests were conducted to identify the essential factors necessary for calculating wind loads and the variables influencing these factors. The building shape considered was a square, and the wind force coefficients and power spectral density were measured by combining 4 ground roughness values, 11 side ratios (), 4 aspect ratios (), and wind directions ranging from 0° to 90°. Subsequently, a generalized formulation was devised to facilitate wind load calculations across diverse conditions and a method for calculating load combination coefficients, considering response correlation and load simultaneity, was presented. Finally, the wind loads obtained from the wind tunnel tests were compared with those predicted by the WCP using an actual project model.

Vertical-axis wind turbines (VAWTs) are receiving more and more attention as they involve simple design, cope better with turbulence and are insensitive to wind direction which has a huge impact on the cost since the yaw mechanism is not needed. However, VAWTs still suffer from low conversion efficiency. As a results tremendous efforts are exerted to improve its efficiency which mainly focus on two methods regardless of whether the study is a CFD simulation or a field test or lab test experiment. An active approach which involves the modification of the rotor itself such as the blade design, angle, trailing and leading edges, inner blades, chord thickness, contra-rotating rotor, etc. While the second approach involves passive techniques where the flow is directed to optimally face the downwind rotor by mounting a guiding vane such as a diffuser or other shapes at the upwind position of the rotor. Among all techniques undertaken, the CRWT rotor technique seems to be the most effective with an output even comparable to that of Horizontal Axis Wind Turbines (HAWT), while the Savonius rotor received more attention compared to other designs of VAWTs. Apart from technological issues, it was also suggested that geographical issues such as proper site siting of the wind turbine rotor at a particular location where a uniform flow could be guaranteed is of paramount importance to ensure an effective conversion capacity of wind turbines.

Presently, Jordan confronts a double substantial challenge of enhancing energy security and mitigating greenhouse gas emissions. One of the most encouraging avenues to attain the objectives of sustainable development, energy security, and environmental conservation is to enhance the integration of renewable energy into the generation of electricity. In pursuit of this goal, the Jordanian government intends to expand investments in the green energy sector, with solar and wind energy poised to play a key role in satisfying energy demands and cultivating an environmental sustainability. This paper aims to examine the distinctive dynamics, challenges, obstacles, and potential solutions corresponding to the establishment of community solar and wind farms in Jordan suburban areas. It aims to highlight the opportunities and barriers influencing the track of sustainable energy adoption in the country. Through a comprehensive analysis of the Jordanian context, the goal is to extract insights that can guide policies and practices. Additionally, the findings may serve as a valuable benchmark for other regions confronting similar challenges on their pursuit for a sustainable energy future.

In this work, we explore the ability to dynamically group the Wind Turbine (WT) of a Wind Farm (WF) based on the behaviour of some of their Supervisory Control And Data Acquisition (SCADA) signals to detect the turbines that exhibit abnormal behaviour. We centre this study on a small WF of five WTs. We use the fact that the same signals from different turbines in the same WF coherently evolve temporally in a time domain, describing very similar waveforms. In this contribution, we use averaged signals from the SCADA system and omit maximums, minimums and standard deviations, focusing mainly on velocities and other slowly varying signals. For the temporal analysis, sliding windows of different temporal durations and overlapings are explored. The capability to automatically identify WTs whose signals differ from the group’s behaviour can alert and program preventive maintenance operations on such WTs before a major breakdown occurs.

The interaction between the grid network and the offshore wind power plant (WPP) network can lead to the amplification of certain harmonics and potentially resonant conditions. Offshore WPP should limit the increment of harmonic voltage distortion at the point of connection to the grid network as well as within their internal network. The harmonic distortion should be limited within the planning level limits using harmonic compensation, which is usually achieved by using static filters. In this paper an active damping compensation strategy with a STATCOM using emulation of resistance at the harmonic frequencies of concern is analysed. Such a compensation is effective for the local bus, though the performance is not guaranteed at the remote bus. This paper investigates the challenges associated with remote harmonic compensation in the offshore WPP, which is connected to the onshore grid through long high-voltage cables and transformers. First, the harmonic distortion and the compensating effects of the filter are theoretically assessed. Afterwards, they are demonstrated using harmonic propagation studies and time domain simulations in PSCAD.

Objective: Infliximab (IFX) concentrations are a predictive factor (PF) of pharmacokinetic (PK) origin in the treatment of Crohn’s disease (CD). We evaluated clearance, another PF of PK origin, either alone or in combination with concentrations. Methods: PF of PK origin were evaluated from two cohorts, the first received standard dosing (n=37), and the second was designed to proactively target therapeutic IFX concentrations (n=108). Concentrations were measured using homogenous mobility shift assay. Clearance was estimated using nonlinear mixed effects methods with Bayesian priors. C-reactive protein based clinical remission (<3mg/L in the absence of symptoms) was used for the disease control outcome. Longitudinal changes in disease control due to factors including time, IFX concentration, and clearance were analyzed using repeated event analysis. Change in objective function value (∆OFV) was calculated to compare concentration and clearance. Results: Lower baseline clearance and proactive dosing associated with enhanced disease control during induction (p<0.01). Higher IFX concentrations and lower Clearance measured at the second, third and fourth infusion yielded improved disease control during maintenance (p<0.032). During maintenance, the association with disease control was better with clearance than with concentrations (∆OFV= -19.2; p<0.001), and the combination of both further minimized OFV (p<0.001) with markedly improved clinical yield in the presence of both PF of PK origin. Conclusion: PF of PK origin and lower clearance during induction and maintenance yielded enhanced disease control in pediatric CD treated with IFX. The combination of IFX concentration and clearance are better predictors of therapeutic outcome compared to either one alone.

In this paper, the feasibility and potential assessment (PA) of wind power in six different areas MehalMeda, Eneware, DebreBerhan, AlemKetema, GundoMekel, and Majet are investigated. The data is collected from the National Metrological Agency (NMA) in Addis Ababa and from the districts of the case study areas and analyzed using MATLAB and HOMER software. Using the data collected at 10 meter height, wind direction using a wind rose, the wind frequency distribution, and wind turbine characteristics have been analyzed. Moreover, to obtain a more realistic wind potential study, the wind speed at a 10 meter height is extrapolated to a height of 50 meter in order to determine wind speed, wind power density, and wind energy density. The average wind speed of the zone at 10m and 50m heights are 1.58 m/s and 1.99 m/s, 3.06 m/s and 3.85 m/s, 4.75 m/s and 5.98 m/s, 2.29 m/s and 2.88 m/s, 1.01 m/s and 1.27 m/s and 4.07 and 5.12m/s at Alemketema, Debreberhan, Eneware, Gundemeskel, Majete and Mehalmeda respectively. The extrapolated result shows that the maximum wind speed and power densities at a height of 50 meter for Eneware, MehalMeda and Debre Berhan are 10.4 m/s, 689 W/m2, 8.9m/s, 429 W/m2 and 6.3m/s, 152.2 W/m2 respectively. The energy densities at a height of 50 meter for AlemKetema, DebreBerhan, Eneware, GundoMekel, Majete, and MehalMeda are 181.06 kWh/m2*yr , 1332.83 kWh/ m2*yr, 6078.91 kWh/ m2*yr, 857.76 kWh/ m2*yr, 58.78 kWh/ m2*yr, and 3939.42 kWh/ m2*yr respectively. As per the international standard for wind power and wind speed classification, considering the extrapolated height, Eneware, MehalMeda, and DebreBerhan have feasible wind potential for both small-scale and large-scale wind farm implementation, whereas Majete, AlemKetema, and GundoMeskel of the North Shewa Zone in the Amhara region have poor wind potential.

The spectra and global distributions of the X-ray emissions generated by the solar wind charge-exchange (SWCX) process in the terrestrial magnetosheath are investigated based on a global hybrid model and a global geocoronal hydrogen model. The solar wind O6+ ions which are the primary charge state for oxygen ions in solar wind are considered. The line emissivity of the charge-exchange born O5+ ions are calculated by Spectral Analysis System for Astrophysical and Lab oratory (SASAL). It is found that the emission lines from the O5+ ranges from 105.607 to 118.291 eV with the strong line at 107.047 eV. We then simulated the magnetosheath X-ray emission intensity distributions with a virtual camera at two positions of north pole and dusk at six stages during the passing of a perpendicular interplanetary shock combined with a tangential discontinuity structure through the Earth’s magnetosphere. During this process, the X-ray emission intensity increases with time, and the maximum value is 27.11 keV cm-2 s-1 sr-1 on the dayside, which is 4.5 times that before the solar wind structure reaches the Earth. A clear shock structure can be seen in the magnetosheath and moves earthward. The maximum emission intensity seen at dusk is always higher than that seen at north pole.

The limitedness of the nonrenewable local energy resources in Israel, even in background of the later gas fields’ findings, continues to force the state to devote various efforts for the ‘green’ energy development. These efforts include installations both in the solar and in the wind energy, with a purpose to improve the diversity of energy sources. While the standard discounted cash flow (DCF) method using the net present value (NPV) criterion is extensively adopted to evaluate investments, the standard DCF method is inappropriate for the rapidly changing investment climate and for the managerial flexibility in investment decisions. In recent years, the real options analysis (ROA) technique is widely applied in many studies for valuation of renewable energy investment projects. Hence, we apply in this study the real options analysis approach for the valuation of wind energy turbines and apply it to the analysis of wind energy economic potential in Israel.

With the increasing use of data-driven modeling methods new approaches to complex problems in the field of wind energy can be addressed. Topics reviewed through literature include wake modeling, performance monitoring and controls applications, condition monitoring and fault detection, and other data-driven research. Literature shows the advantages of data-driven methods reduce computational expense or complexity, particularly in the cases of wake modeling and controls, as well as various data-driven methodologies’ aptitude for predictive modeling and classification, as in the cases of fault detection and diagnosis. Significant work exists for fault detection while less work is found for controls applications. A methodology for creating data-driven wind turbine models for arbitrary performance parameters is proposed. Results are presented utilizing the methodology to create wind turbine models relating active adaptive twist to steady-state rotor thrust as a performance parameter of interest. Resulting models are evaluated by comparing root-mean-square-error (RMSE) on both the training and validation data sets, with Gaussian Process Regression (GPR), deemed an accurate model for this application. The resulting model undergoes particle swarm optimization to determine the optimal aerostructure twist shape at a given wind speed with respect to the modeled performance parameter, aerodynamic thrust load. The optimization process shows an improvement of 3.15% in thrust loading for the 10 MW reference turbine, and 2.66% for the 15 MW reference turbine.

With the developments of smart technologies, the use of rare earth elements (REEs) knows a widespread use, thus, their importance as valuable and strategic metals boosted to levels never known before. Due to their scarcity in Earth crust, the recovery of these elements from secondary resources also knows further developments. Traditional pyrometallurgical and hydrometallurgical processing, though of wide use, in the recovery of these REEs, have some environmental drawbacks, thus, the development of new recovery approaches are under developments. Here, Solvometallurgy appeared as a friendly environmental technology, and ionic liquids and deep eutectic solvents re-sulted as a first-row chemicals to be used in the different unit operations used in solvometallurgical processing: leaching, liquid-liquid extraction, ion exchange (adsorption), precipitation and elec-trolysis. This manuscript reviewed the most recent literature concerning the use of ionic liquids and deep eutectic solvents in the recovery of REEs from various sources.

Securing the structural safety of blades has become crucial, owing to the increasing size and weight of blades resulting from the recent development of large wind turbines. Composites are primarily used for blade manufacturing because of their high specific strength and specific stiff-ness. However, in composite blades, joints may experience fractures from the loads generated during wind turbine operation, leading to deformation caused by changes in the structural stiff-ness. In this study, 7,132 debonding damage data, classified by damage type, position, and size, are selected to predict debonding damage based on natural frequency. The change in the natural frequency caused by debonding damage is acquired through finite element (FE) modeling and modal analysis. Synchronization between the FE analysis model and manufactured blades is achieved through modal testing and data analysis. Finally, the relationship between the debond-ing damage and the change in natural frequency is examined using artificial neural network techniques

The quiet-time solar wind electrons feature non-thermal characteristics when viewed from the perspective of their velocity distribution functions. They typically have an appearance of being composed of a denser thermal “core” population plus a tenuous energetic “halo” population. At first, such a feature was empirically fitted with the Kappa velocity space distribution function, but ever since the ground-breaking work by Tsallis, the space physics community has embraced the potential implication of the Kappa distribution as reflecting the non-extensive nature of the space plasma. From the viewpoint of microscopic plasma theory, the formation of non-thermal electron velocity distribution function can be interpreted in terms of the plasma being in a state of turbulent quasi equilibrium. Such a finding brings forth the possible existence of a profound inter-relationship between the non-extensive statistical state and the turbulent quasi-equilibrium state. The present paper further develops the idea of solar wind electrons being in the turbulent equilibrium, but unlike the previous model, which involves the electrostatic turbulence near the plasma oscillation frequency (i.e., Langmuir turbulence), the present paper considers the impact of transverse electromagnetic turbulence, particularly, the turbulence in the whistler-mode frequency range. It is found that the coupling of spontaneously-emitted thermal fluctuations and the background turbulence leads to the formation of non-thermal electron velocity distribution function of the type observed in the solar wind during quiet times. This demonstrates that the whistler-range turbulence represents an alternative mechanism for producing the Kappa-like non-thermal distribution, especially close to the Sun and in the near-Earth space environment.

To make wind power more competitive, it is necessary to reduce turbine downtime and reduce costs associated with wind turbine Operation and Maintenance (O&amp;M). Incorporating machine learning in developing condition-based predictive maintenance methodologies for wind turbines can enhance their efficiency and reliability. This paper presents a monitoring method that utilizes Base Density for the Support Vector Machine (BDSVM) and the evolutionary Fourier spectra of vibrations. This method allows smart monitoring of the function evolution of the turbine. A complex optimal function (FO) for 5-degree order has been developed that will be the boundary function of the BDSVM to timely determine the magnitude, frequency, and place of the failure occurring in wind turbine drive.

When dealing with limited sample sizes or missing values in time series data, achieving high accuracy in forecasting becomes challenging. This challenge is particularly common in wind energy forecasting, where many wind farms lack complete data. In this paper, we employ the widely-used ARIMA (Autoregressive Integrated Moving Average) model for time series forecasting. To address the difficulties posed by limited sample sizes and missing values, we adopt a unique approach by utilizing multiple ARIMA models for different datasets. A key distinction from other multiple models methods for time series forecasting lies in each model within our approach using its own dataset, making the fusion process more intricate. To overcome this, we incorporate neural networks and two techniques for model fusion: direct fusion with a learning mechanism and compensation for missing data through training. For each ARIMA model, we introduce a noise estimation method to circumvent the white noise assumptions inherent in ARIMA models. Finally, we apply these methods to wind energy prediction, and our experimental results showcase a significant enhancement in forecasting accuracy.

As novel materials for carbon capture, phase change solvents can separate into two immiscible phases during the CO2 capturing procedure under a certain temperature. The solvent systems can significantly decrease the energy consumption since the solvents can be regenerated by only heating the rich-CO2 phase. In this work, amino acid ionic liquids (AAILs) were synthesized using quaternary ammonium salts and amino acids as raw materials, and the aqueous solutions were prepared as novel liquid-solid phase change solvents. The results showed that the solvents had excellent CO2 absorption capacity, and the AAILs functionalized by glycine and tryptophan exhibited significant phase change properties. The mechanism of phase-change of the solvent were mainly due to the lower solubility of the product after reaction between AAILs and CO2. The solvent with tryptophan as anion could be regenerated by only heating the CO2-riched solid phase, which might significantly decrease energy consumption of regeneration. And the absorbent could be reused with the regenerated absorption ratio up to 79%. The solvent system has great potential in industrial application due to the easy operation process and efficient recycling ability.

The present study provides molecular insight into the mechanisms underlying energy dissipation and lubrication of a smooth contact lubricated by an ionic liquid. We have performed normal and lateral force measurements with a surface forces apparatus and by colloidal probe atomic force microscopy on following model systems: 1-ethyl-3-methyl imidazolium bis-(trifluoro-methylsulfonyl)imide, in dry state and in equilibrium with ambient (humid) air; the surface was either bare mica or functionalized with a polymer brush. The velocity-dependence of the friction force reveals two different regimes of lubrication, boundary-film lubrication, with distinct characteristics for each model system, and fluid-film lubrication above a transition velocity V*. The underlying mechanisms of energy dissipation are evaluated with molecular models for stress-activated slip and flow, respectively. The stress-activated slip assumes that two boundary layers (composed of ions/water strongly adsorbed to the surface) slide pass each; the bond dynamics and the strength of the interaction at the slip plane dictate the change in friction -decreasing, increasing or remaining constant- with velocity in the boundary-film lubrication regime. Above a transition velocity V*, friction monotonically increases with velocity in the three model systems. Here, layers of ions slide past each (“flow”) under a shear stress and friction depends on a shear-activation volume that is significantly affected by confinement. The proposed friction model provides a molecular perspective of the lubrication of smooth contacts by ionic liquids and allows identifying the physical parameters that control friction.

Vertical wind speed extrapolation is a commonly used method that involves estimating wind speeds at various heights based on measurements taken at a specific height. In this study, we compared the short-and long-term extrapolation methods of wind parameters using data collected on site by anemometers at two different heights. We assessed the accuracy of these methods by calculating the statistical indicators for performance evaluation, and then determined the most appropriate model for the two types of vertical extrapolation. Additionally, we evaluated energy potential characteristics, as well as the statistical analysis of wind speed distribution and wind power density based on the Weibull and Rayleigh distribution. Our results indicated that the power law is the most suitable model for the short-term method, while the modified Mikhail model is the most appropriate for long-term extrapolation. We also found that the wind potential of this area is favorable for wind turbine integration.

Nanocellulose has gained increasing attention during the past decade, which is related to its unique properties and wide application. In this paper, nanocellulose was produced by hydrolysis with ionic liquids (1-ethyl-3-methylimidazole acetate (EmimOAc) and 1-allyl-3-methylimidazolium chloride (AmimCl)) from microcrystalline cellulose (Avicel and Whatman) subjected to enzymatic pretreatment. The obtained material was characterized by Fourier transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), dynamic light scattering (DLS), scanning electron microscope (SEM) and thermogravimetric analysis (TG). The results showed that the nanocellulose had a regular and spherical structure with a diameter of 30-40 nm and exhibited lower crystallinity and thermal stability than the material after hydrolysis with Trichoderma reesei enzymes. However, the enzyme-pretreated Avicel had a particle size of about 200 nm and a cellulose II structure. A two-step process involving enzyme-pretreatment and hydrolysis with ionic liquids resulted in the production of nanocellulose. Moreover, the particle size of nanocellulose and its structure depend on the ionic liquid used.

The development and utilization of wind energy is of great significance to the sustainable development of China's economy and the realization of the goal of "dual carbon". Under the typhoon system, the randomness and volatility of wind speed become an important basis for affecting the energy efficiency utilization and design of wind turbines. Therefore, based on wind speed and wind direction data at 10m, 30m, 50m and 70m heights of a wind power tower in Yancheng, Jiangsu Province, this paper analyzes the change characteristics of wind speed and wind direction by using BFAST method and Hurst index. Based on typhoon body data, topographic data and mesoscale system wind direction data, the causes of the occurrence and development of wind speed and wind direction of wind tower are further analyzed, and a conclusion is drawn: (1) In BEAST method, there are 5, 5, 6 and 6 change points at the height of 10m, 30m, 50m and 70m respectively. Among them, the change points at the height of 10m, 30m and 50m all change before and after node 325, and the change time point at the height of 70m is inconsistent with other heights. Hurst index results show that the inconsistency at 70m altitude is stronger than that at other altitudes. (2) The wind direction sequence at 10m, 30m, 50m and 70m altitude is fitted by stages, and the direction of wind direction is SE-E-SE-SW-W-NW, where, At the height of 70m, the deviation of the fitting trend line from other altitudes is larger in the wind speed strengthening stage and weakening stage. (3) The wind speed at the height of 10m and 70m has different response degrees to the typhoon body. The correlation between the wind speed and the distance between the wind measurement tower and the typhoon near the center is stronger at the height of 10m than at the height of 70m. The surface type and the wind direction of the mesoscale system also have certain effects on the wind speed and direction. In this paper, the change characteristics and influencing factors of wind speed and direction of wind tower are studied, which provides methods and theoretical support for the study of short-term wind speed when typhoon passes through, and provides reliable support for the selection of wind power forecast indicators and the selection and design of wind turbines under extreme gale weather systems.

In this study, we aim to evaluate how cyclodextrin molecules affect the hydrophilicity and selec-tivity of PVDF membrane. Herein, we prepared PVDF-PVP(1-x) β-CDx membranes, with x rang-ing from 0 to 1 wt%. The membranes were deeply characterized by means of X-ray diffraction (XRD), attenuated total reflectance infrared (ATR-IR), Raman spectroscopies, Thermal gravimet-ric analysis (TGA), Contact angle measurement (CA), scanning electron microscopy (SEM) and atomic force microscopy (AFM). The study unequivocally demonstrates the effectiveness of the addition of β-CD molecules on membranes' structural, morphological, and dielectric properties. Adding 0.25wt% β-CD enhanced hydrophilicity, with CA decreasing from 72.6° to 56° and roughness decreasing from 81 to 29 nm. The PVDF-PVP(1-x) β-CDx membranes were then fully characterized using electrochemical impedance spectroscopy (EIS) to determine their dielectric properties, which clearly showed that the presence of β-CD induced polarization of the mem-brane. The separation of various dyes with different sizes and charges was utilized. These dyes included methylene blue (MB, positive, 0.504 nm), methyl red (MR, neutral, 0.487 nm), rose Bengal (RB, negative, 0.588 nm), and brilliant blue (BB, negative, 0.798 nm). Based on our re-search, we found that the membrane's selectivity is determined by both exclusion factors (such as size and dielectric properties) and inclusion inside the β-CD cage. We found that using alpha-CD instead of beta-CD led to the disappearance of dye inclusion. These findings strongly sug-gest that β-CD molecules can be a viable solution for dye removal from wastewater.

The dust originating from the extinct lake of the Aral Sea poses a considerable threat to the sur-rounding communities and ecosystems. The accurate location of these wind erosion areas is an essential prerequisite for controlling sand and dust activity. However, few relevant indicators re-ported in the current study can accurately describe and measure wind erosion intensity. A novel wind erosion intensity (WEI) of a resolution unit was defined in this paper based on the deformation due to the wind erosion in this resolution unit. We also derived the relationship between WEI and soil InSAR temporal decorrelation (ITD). The ITD is usually caused by the surface change over time, which is very suitable for describing wind erosion. However, within one resolution unit, the ITD signal usually includes soil and vegetation contributions, and few studies are referred to this. Therefore, we proposed an ITD decomposition model (ITDDM) to decompose the ITD signal of a resolution unit. The least-squares method (LSM) based on singular value decomposition (SVD) is used to estimate the ITD of soil (SITD) within a resolution unit. We verified the results qualitatively by the landscape photos, which can reflect the actual conditions of the soil. At last, the WEI of the Aral Sea from June 23, 2020, to July 05, 2020, was mapped. The results confirmed that (1) Based on the ITDDM model, the SITD can be accurately estimated by the LSM method, (2) the Aral Sea is experiencing severe wind erosion, and (3) The middle, northeast, and southeast bare areas of the South Aral Sea are where salt dust storms may occur.

Combining wind and solar photovoltaic (PV) generation can provide complementary renewable power production, but depends on correlated resources. This study analyzed 10 years of wind data from Naama, Algeria to evaluate the potential for evening wind generation to offset the loss of solar at sunset. Average wind speeds showed a distinct increase during evening hours, coinciding with the decrease in solar irradiance. Wind turbine simulations using a 1.5 MW turbine and the wind data showed sufficient resources for profitable power production after sunset. Statistical analyses confirmed significantly higher wind speeds and simulated power output in evening vs daylight periods (p&lt;0.05). The Pearson correlation coefficient between evening wind speeds and decreasing solar irradiance was 0.63, supporting a strong positive relationship. These findings indicate Naama has adequate wind resources to deploy economically viable wind power capacity that can complement existing solar infrastructure and provide renewable electricity after dark , .

The preservative qualities of individual ionic compounds on the infectivity of T4 virions were elucidated. T4 virions were immersed in quasi-pure ionic solutions prior to the adsorption process, and the pfu values of these were measured following the conventional method. In neutral ionic solutions, the minimum and the optimum concentrations for preservative qualities were corresponded with the results obtained from the multi-ionic media/buffers. In acid and alkali solutions, phages show tolerances at a pH range of 5-11 in multi-ionic media/buffers. T4 virions show no tolerance in quasi-pure acid, neutral and weak alkaline conditions. The preservative quality of T4 virions was jumped up in over 10-1 mM OH- solution, equivalent to pH value over 10, which is corresponding to the pKa of the deprotonation of the DNA bases G and T. Infectivity was lost below 10-1 mM OH- and higher than 10 mM OH-. These results implicate the maintaining of infectivity of a virion may need the flexibility of the intra-capsid DNA by deprotonation.

All-solid-state lithium batteries (ASSLBs) using argyrodite electrolyte materials have shown promise for applications in electric vehicles (EVs). However, understanding the effects of pro-cessing parameters on the ionic conductivity of these electrolytes is crucial for optimizing battery performance and manufacturing methods. This study investigates the influence of electrolyte op-erating temperature, electrolyte operating pressure, electrolyte pelletization pressure, and electro-lyte pelletizing temperature on the ionic conductivity of Li6PS5Cl0.5Br0.5 argyrodite electrolyte (AmpceraTM, D50=10 µm). A specially designed test cell is employed for the experimental meas-urements, allowing for controlled pelletization and testing within the same tooling. The results demonstrate the significant impact of the four parameters on the ionic conductivity of the argy-rodite electrolyte. The electrolyte operating temperature has a more pronounced effect than oper-ating pressure, and pelletizing temperature exerts a greater influence than pelletizing pressure. This study provides graphs that aid in understanding the interplay between these parameters and achieving desired conductivity values. It also establishes a baseline for the maximum pelletizing temperature before undesirable degradation of electrolyte occurs. By manipulating the pelletizing pressure, operating pressure, and pelletizing temperature, battery engineers can achieve the desired conductivity for specific applications. The findings emphasize the need to consider operating conditions to ensure satisfactory low-temperature performance, particularly for EVs. Overall, this study provides valuable insights into processing and operating conditions for ASSLBs utilizing Li6PS5Cl0.5Br0.5 argyrodite electrolyte.

This work compared the performance of three methods for constructing a regional ensemble prediction system (EPS) for wind speed forecasts: dynamical downscaling, breeding of growth modes (BGM), and blending method. The Weather Research and Forecasting (WRF) model was used to downscale the European Centre for Medium-range Weather Forecast (ECMWF) EPS. In addition, as the BGM method needs observation data for generating scaling factors, an alternative method for generating scaling factors was proposed to eliminate dependence on observation data. One-month tests between October 1st and October 30th, 2020, were implemented to evaluate the performance of three methods in the Gansu province of China. The results demonstrate that the blending method outperforms the other two methods. Furthermore, the difference in performance is evident mainly in early forecast lead time and becomes negligible as forecast time increases.

The processes of the sublimation and thermal decomposition of the 1‐ethyl‐3‐methylimidazolium hexafluorophosphate ionic liquid (EMImPF6) were studied by a complex approach including Knudsen effusion mass spectrometry, IR and NMR spectroscopy, and quantum chemical calculations. It was established that the vapor over liquid phase primarily consists of decomposition products under equilibrium conditions. Otherwise, the neutral ion pairs are the only vapor components under Langmuir conditions. To identify the nature of the decomposition products an experiment on the distillation of the ionic liquid was performed and the collected distillate was analyzed. It was revealed by the IR and NMR spectroscopy that EMImPF6 decomposes to substituted imidazole‐2‐ylidene (C6N2H10PF5) and HF. The measured vapor pressure of C6N2H10PF5 reveals a very low activity of the decomposition products (&lt;10–4) in the liquid phase. The absence of significant accumulation of decomposition products in the condensed phase makes it possible to determine the enthalpy of sublimation of the ionic liquid assuming its unchanged activity. The thermodynamics of the EMImPF6 sublimation was studied by Knudsen effusion mass spectrometry. The formation enthalpy of EMImPF6 in ideal gas state was found from combination of the sublimation enthalpy and formation enthalpy of ionic liquid in the condensed state. The obtained value is in good agreement with those calculated by quantum chemical methods.

(200 words) Imidazolium ionic liquids containing acetylacetone, thenoyltrifluoroacetone, or 8-hydroxyquinoline, respectively, were used as the extracting agents for the separation of traces of iron (III) from its aqueous solutions with or without citric and oxalic acids. The results show that 8-hydroxyquinoline in imidazolium ionic liquids extract iron quantitatively from all the tested solutions including complexing ones, regardless indications of unexpected iron behavior/speciation.

Sea surface wind forecasts in the Adriatic Sea often suffer for unadequate modelling, especially for the wind speed. This has detrimental effects on the accuracy of sea level and storm surge predictions. We present a numerical method to reduce the bias between the sea surface wind observed by the scatterometers and that supplied by the European Centre for Medium-Range Weather Forecasts (ECMWF) global atmospheric model, for storm surge forecasting applications. The method, called “wind bias mitigation”, relies on scatterometer observations to determine a multiplicative factor ∆ws which modulates the standard model wind in order to decrease the bias between scatterometer and model. We compare four different mathematical approaches to this method, for a total of eight different formulations of the multiplicative factor ∆ws. Four datasets are used for the assessment of the eight different bias mitigation methods: a collection of 29 Storm Surge Events (SEVs) cases in the years 2004-2014, a collection of 48 SEVs in the years 2013-2016, a collection of 364 cases of random sea level conditions in the same period, and a collection of the seven SEVs in 2012-2016 that were worst predicted by the Centro Previsioni e Segnalazioni Maree, Comune di Venezia (Tide Forecast and Early Warning Centre of the Venice Municipality - CPSM). The statistical analysis shows that the bias mitigation procedures supplies a mean wind speed more accurate than the standard forecast, when compared with scatterometer observations, in more than 70% of the analyzed cases.

The wind industry is looking for ways to accurately predict the reliability and availability of newly installed wind turbines. Failure modes, effects and criticality analysis (FMECA) is a technique utilized for determining the critical subsystems of wind turbines. There are several studies which applied FMECA for wind turbines in the literature, but no studies so far have considered different weather conditions or climatic regions. Furthermore, various design types of wind turbines have been analyzed applying FMECA but no study so far has applied FMECA to compare the reliability of geared and direct-drive wind turbines. We propose to fill these gaps by using Koppen-Geiger climatic regions and two different turbine models of direct-drive and geared-drive concepts. A case study is applied on German wind farms utilizing the WMEP database which contains wind turbine failure data from 1989 to 2008. This proposed methodology increases the accuracy of reliability and availability predictions and compares different wind turbine design types and eliminates underestimation of impacts of different weather conditions.

The kinetic energy transfer between the atmosphere and oceans, called wind work, affects ocean dynamics including near-inertial oscillations and internal gravity waves, mesoscale eddies, and large-scale zonal jets. For the most part, recent numerical estimates of global wind work amplitude are almost 5 times larger than those reported 10 years ago. This large increase is explained by the impact of the broad range of spatial and temporal scales covered by winds and currents, the smallest of which have only recently been uncovered by increasingly high resolution modeling efforts. However, existing satellite observations do not fully sample this broad range of scales. The present study assesses the capabilities of ODYSEA, a conceptual satellite mission to estimate the amplitude of wind work in the global ocean. To this end, we use an ODYSEA measurement simulator fed by the outputs of a km-scale coupled ocean-atmosphere model to estimate wind work globally. Results indicate that compared with numerical truth estimates, the ODYSEA instrument performs well globally, except for latitudes north of 40∘N during summer due to unresolved storm evolution. This performance is explained by the wide-swath properties of ODYSEA (a 1,700 km wide swath with 5 km posting for winds and surface currents), its twice-a-day (daily) coverage at mid-latitudes (low latitudes), and the insensitivity of the wind work to uncorrelated errors in estimated wind and current.

The importance of rare earth elements as the basis in the development of new technologies or the improvement of the used ones, made of a necessity its recovery, besides that from raw materials, from waste materials. In this recovery, Hydrometallurgy and its derivative Solvometallurgy, play a key role due to its operational characteristics, which are emphasized with the use of ionic liquids. The manuscript reviewed the most recent advances (2023 and 2024 years) about the use of ionic liquids in the unit operations (leaching and separation technologies) aimed to the recovery of these valuable and strategic metals. Moreover, a comprehensive review about the use of these chemicals in the development of advanced materials containing some of these rare earth elements is presented.

The recovery of precious metals is a project with both economic and environmental significance. In this paper, it presents how to use bacterial mineralization to selectively recover gold from multi-ionic aqueous systems. The Bacillus licheniformis FZUL-63, separated from a landscape lake in FuZhou University, was shown to selectively mineralize and precipitate gold from coexisting ions in aqueous solution. The removal of Au(III) was almost happened in first hour, and FTIR data show that the amino, carboxyl and phosphate groups on the surface of the bacteria are related to the adsorption of gold ions. XPS results implied that Au(III) ions are reduced to monovalent, and then the Au(I) was adsorbed on the bacterial surface at the beginning stage(first hour). XRD results showed the gold biomineralization began about 10 hours after the interaction between Au(III) ions and bacteria. The Au(III) mineralization has been rarely influenced by other co-existing metal ions. TEM analysis shows the gold nanoparticles are polyhedral structure with a particle size of ~20 nm. The Bacillus licheniformis FZUL-63 could selectively mineralize and recover 478 mg/g(dry biomass) gold from aqua regia-based metal wastewater through four cycles. It could be of great potential in the practical application.

Ion current rectification (ICR) is the ratio of ion current by forward bias to by backward bias and is a critical indicator of diode performance. In previous studies, many attempts have been continued to improve the performance of this ICR, but there is the intrinsic problem for geometric changes that induce ionic rectification due to their fabrication problem. Additionally, the high ICR could be achieved in the narrow salt concentration range only. Here, we propose a multi-layered bipolar ionic diode based on an asymmetric nanochannel network membrane (NCNM), which is realized by soft lithography and self-assembly of homogenous-sized nanoparticles. Owing to the freely changeable geometry based on soft lithography, the ICR performance can be explored according to the variation of microchannel shape. Interestingly, very stable ICR performance can be achieved using the multi-layered 3D configuration for the bipolar diode in a broad range of salt concentrations (0.1mM ~ 100 mM). This demonstrates the promising potential of multi-layered NCNM for applications in highly concentrated electrolytes, such as biosensors, desalination, or energy harvesting.

Common buckwheat (Fagopyrum esculentum Moench) is an annual spring-emerging crop that is classified among dicotyledons, yet due to the manner of its cultivation, use, and chemical composition of seeds. The use of buckwheat straw for energy purposes, for example, for the production of second generation bioethanol might enable its wider application and increase the cost-effectiveness of tillage. In this study, we examined the usability of buckwheat straw for the production of bioethanol. We pretreated the raw material with using ionic liquids and subsequently performed enzymatic hydrolysis and alcoholic fermentation. The obtained chemometric data was analyzed using the Partial Least Squares (PLS) regression model. PLS regression in combination with the spectral analysis within near-infrared (NIR) spectrum allowed for the rapid determination of amount of cellulose in the raw material and also provided information on the changes taking place in its structure. According to our results, we obtained good results for the combination of 1-ethyl-3-methylimidazolium acetate as the ionic liquid and Cellic CTec2 and the enzymatic preparation for the pretreatment of buckwheat straw. The highest concentration of glucose following 72 hours of enzymatic hydrolysis was found to be around 5.5 g/dm3. The highest concentration of ethanol (3.31 g/dm3) was obtained with the combination of 1-butyl-3-methylimidazolium acetate for the pretreatment and the cellulase from Trichoderma reesei for enzymatic hydrolysis. In summary, the efficiency of the fermentation process is strictly associated with the pool of available fermenting sugars, and it depends on the type of ionic liquid used during the pretreatment and on the enzymatic preparation. It is possible to obtain bioethanol from buckwheat straw using ionic liquid for the pretreatment of the raw material prior to the enzymatic hydrolysis and alcoholic fermentation of the material.

The use of mixed-state ionic beams in collision dynamics investigations is examined. Using high resolution Auger projectile spectroscopy involving He-like ($1s^2\thinspace^1\!S, 1s2s\thinspace^{3,1}\!S$) mixed-state beams, the spectrum contributions of the $1s2s\thinspace^3\!S$ metastable beam component is effectively separated and clearly identified. This is performed with a technique that exploits two independent spectrum measurements under the same collision conditions, but with ions having quite different metastable fractions, judiciously selected by varying the ion beam charge-stripping conditions. Details of the technique are presented together with characteristic examples. In collisions of 4 MeV B$^{3+}$ with H$_2$ targets, the Auger electron spectrum of the separated $1s2s\thinspace^{3}S$ boron beam component allows for a detailed analysis of the formation of the $1s2s(^3\!S)nl \thinspace^2\!L$ states by direct $nl$ transfer. In addition, the production of hollow $2s2p\thinspace^{1,3}\!P$ doubly- and $2s2p^2\thinspace^2\!D$ triply-excited states, by direct excitation and transfer-excitation processes, respectively, can also be independently studied. In similar mixed-state beam collisions of 15 MeV C$^{4+}$ with H$_2$, He, Ne and Ar targets, the contributions of the $1s^2$, $1s2s\thinspace^{3,1}S$ beam components to the formation of the $2s2p\thinspace^{3,1}\!P$ states by double-excitation, $1s\rightarrow2p$ excitation and transfer-loss processes can be clearly identified, facilitating comparisons with theoretical calculations.

Simultaneous extraction of trypsin inhibitors and soy isoflavones from soybean meal was investigated using the non-destructive phytochemical extraction process, namely aqueous micellar system. The ethoxylated aliphatic alcohols Genapol X-080, Tergitol 15-S-7, and Tergitol 15-S-9, all non-toxic and biodegradable surfactants, were assessed as potential extractants. A Box-Behnken multifactorial design with the application of the Derringer desirability was used to determine the conditions that maximized the trypsin inhibitors and isoflavone extraction while minimizing the protein extraction. The optimum condition of 5% m/m of surfactant in 50 mM aqueous sodium citrate solution pH 4.5, at 45 °C for 45 min, was established for the three surfactants. The novel methodology would allow the extraction of the main soybean antinutritional factors, trypsin inhibitors, and the valuable isoflavones, preserving the nutritional quality of the treated material. This represents a sustainable alternative methodology for industrial purposes due to its low cost, biodegradability, non-toxicity, and easy scaling up.

More and more works are using machine learning techniques while adopting supervisory control and data acquisition (SCADA) system for wind turbine anomaly or failure detection. While parameter selection is important for modelling a wind turbine’s health condition, only a few papers have been published focusing on this issue and in those papers interconnections among sub-components in a wind turbine are used to address this problem. However, merely the interconnections for decision making sometimes is too general to provide a parameter list considering the differences of each SCADA dataset. In this paper, a method is proposed to provide more detailed suggestions on parameter selection based on mutual information. Moreover, after proving that Copula, a multivariate probability distribution for which the marginal probability distribution of each variable is uniform is capable of simplifying the estimation of mutual information, an empirical copula based mutual information estimation method (ECMI) is introduced for an application. After that, a real SCADA dataset is adopted to test the method, and the results show the effectiveness of the ECMI in providing parameter selection suggestions when physical knowledge is not accurate enough.

Deterministic simulations using the SWAN model were conducted along a stretch of the Tietê-Paraná waterway in the Ilha Solteira dam reservoir, São Paulo, Brazil, to assess the water waves generated by winds. Simultaneously employs a probabilistic metamodeling approach (PCE) and Sobol indices, to quantify uncertainty of the five involved physical parameters (wind velocity and direction, bottom friction (JONSWAP), whitecapping and depth-induced breaking index). In the deterministic part, Janssen’s formulation yielded the most successful and accurate estimations of wave heights. Probabilistic analysis underscored the importance of wind data and the whitecapping parameter in model calibration, with a significant influence of wind speed indicated by Sobol indices. The results not only refined the model calibration process, but also allowed the creation of contour maps for wave height and period that offer practical pre-project applications. This work advances understanding of wind wave hydrodynamics deterministically and probabilistically, with good concordance and performance indices compared to field data, despite being scarce.

Background: Hurricanes and other wind events are significant disturbances that affect coastal urban forests around the world. Past research has led to the creation of wind resistance ratings for different tree species which can be used in urban forest management efforts to mitigate the effects of these storms. While useful, these ratings have been limited to species common to one global region (Florida, USA).Methods: Drawing on past ratings and data from a global literature review on tropical storm research, we created a machine learning model to broaden both the geographic coverage and the variety of species currently assessed for their resistance to wind.Results: We were able to assign wind resistance ratings to 281 new species based on the available data and our modelling efforts. The model accuracy and agreement with the original ratings when applied to the testing data set was high with 91% accuracy.Conclusions: The resulting list of wind resistance ratings has been adapted into a spreadsheet-based decision aid for managers, allowing them to assess the overall susceptibility of their urban forest to wind events like hurricanes.

The aim of this research work is to study the influence of temperature, solar irradiation and wind dust on the production of solar energy. In addition, it aims to study the assessment of water quality, in particular groundwater used for cooling and cleaning photovoltaic panels (quality analysis). it's an important source, stable and sustainable can be used entirely for cooling and cleaning PV modules from the sales dust, in order to improve their performance. To date, all research studies carried out in this context of cooling and cleaning using water have not taken account of the nature of this water. We have taken a sample of water from a well in a rural area in the Darra Tafilalet region of Morocco. This region has an arid and semi-arid climate, with very high temperatures and dust-laden winds, particularly in summer. These meteorological characteristics influence the efficiency of cells, particularly photovoltaic (PV) panels, reducing their performance. Next, the water sample was analysed in the laboratory. The results obtained show that the groundwater in this area is very sensitive to cooling and cleaning photovoltaic panels. Moreover, these results indicate that the temperature, solar irradiation and wind-blown dust have a significant influence on energy production.

This article is devoted to overcoming the contradiction between the problem of maximizing the extraction of wind energy as the goal of optimizing wind turbines, and the use of traditional methods based on criteria for the aerodynamic quality of the blades. A modified technique is considered in which the optimization criterion is the directly extracted flow power. It is based on pulse theory methods that use specific power as an optimization criterion. A comparative analysis of the energy efficiency of different types of turbines is carried out, and the effects of blade inversion are considered. A method for calculating multi-rotor turbines based on the concept of uniform power distribution is presented. The compatibility of proprietary and traditional methods is considered by comparing the results of numerical experiments with calculated and experimental data from sources. Optimization computational algorithms generate data from numerical experiments and determine optimal parameter configurations for the turbines under consideration. It is shown that orthogonal Darrieus turbines in high-speed mode provide energy efficiency comparable to collinear turbines, and multi-rotor turbines with power uniformly distributed over the working section are not inferior in energy efficiency to basic turbines, with linear blade velocities halved.

The high-resolution bistatic lidar developed at the Physikalisch-Technische Bundesanstalt (PTB) aims to overcome the limitations of conventional monostatic lidar technology which is widely used for wind velocity measurements in wind energy and meteorology applications. Due to the large measurement volume of a combined optical transmitter and receiver tilting in multiple directions, monostatic lidar generally has poor spatial and temporal resolution. It also exhibits large measurement uncertainty when operated in inhomogeneous flow, for instance, over complex terrain. In contrast, PTB’s bistatic lidar uses three dedicated receivers arranged around a central transmitter, resulting in an exceptionally small measurement volume. The coherent detection and modulation schemes used allow the detection of backscattered, Doppler shifted light down to the scale of single aerosols, realising the simultaneous measurement of all three wind velocity components. This paper outlines design details and the theory of operation of PTB’s bistatic lidar and provides an overview of selected comparative measurements. The results of these measurements have shown that the measurement uncertainty of PTB’s bistatic lidar is well within the measurement uncertainty of traditional cup anemometers, while being fully independent of its site and traceable to the SI units. This allows its use as a transfer standard for the calibration of other remote sensing devices. Overall, PTB’s bistatic lidar shows great potential to universally improve the capability and accuracy of wind velocity measurements, such as for the investigation of highly dynamic flow processes upstream and in the wake of wind turbines.

Wind tunnels are devices that enable researchers to study the flow over objects of interest, the forces acting on them and their interaction with the flow, which is nowadays playing an increasingly important role due to noise pollution. Since the first closed circuit wind tunnel with variable cross-section was built in G¨ottingen, its Prandtl configuration has little change. The wind tunnel with Prandtl configuration has four corners and vanes, more than 50% of the total pressure loss are caused by the corners and vanes. How to reduce the total pressure loss is a world class problem in the wind tunnel design. This study attempts to propose a novel configuration of wind tunnel, where the corners have been replaced by semi-circular tunnel. Sun wind tunnel 2 has only two corners and vanes, while Sun wind tunnel 1 has no corners and vanes at all. It is expected the new wind tunnel can reduce the total pressure loss from 50% to 10%.

Full-scale wind turbine technology has been widely developing in the recent years and condition monitoring techniques assist at the scope of making 100\% technical availability a realistic perspective. In this context, several retrofitting techniques are being used for further improving the efficiency of wind kinetic energy conversion. This kind of interventions is costly and, furthermore, the estimation of the energy enhancement is commonly provided under the hypothesis of ideal conditions, as for example absence of wakes between nearby turbines. A precise quantification of the energy gained by retrofitting is therefore precious in real conditions, that can be very different from ideal ones. In this work, three kinds of retrofitting are studied through the operational data of test case wind farms: improved start-up through pitch angle adjustment near the cut-in, aerodynamic blade retrofitting by means of vortex generators and passive flow control devices, extension of the power curve by raising cut-out and high wind speed cut-in. SCADA data are employed and reliable methods are formulated for estimating the energy improvement from each of the above retrofitting. Further, an insight is provided about wind turbine functioning under very stressing regimes, as for example high wind speeds.

Polyaromatic hydrocarbons (PAHs) are widespread in the interstellar medium (ISM). The abundance and relevance of PAHs call for a clear understanding of their formation mechanisms, which, to date, have not been completely deciphered. Of particular interest is the formation of benzene, the basic building block of PAHs. It has been shown that ionization of neutral clusters can lead to an intra-cluster ionic polymerization process that results in molecular growth. Ab initio molecular dynamics (AIMD) studies in clusters consisting of 3–6 units of acetylene modeling ionization events under ISM conditions have shown maximum aggregation of three acetylene molecules forming bonded C6H6+ species: the larger the number of acetylene molecules, the higher the production of C6H6+. These results lead to the question of whether clusters bigger than those studied thus far promote aggregation beyond three acetylene units, and whether larger clusters can result in higher C6H6+ production. In this study, we report results from AIMD simulations modeling the ionization of 10 and 20 acetylene clusters. The simulations show aggregation of up to four acetylene units producing bonded C8H8+. Interestingly, C8H8+ bicyclic species were identified, setting precedent for their astrochemical identification. Comparable reactivity rates were shown with 10 and 20 acetylene clusters.

The ionic Diels-Alder (I-DA) reactions of a series of six iminium cations with cyclopentadiene have been studied within the Molecular Electron Density Theory (MEDT). The superelectrophilic character of iminium cations,  > 8.20 eV, accounts for the high reactivity of these species participating in I-DA reactions. The activation energies are found between 13 and 20 kcal·mol-1 lower in energy than those associated to the corresponding Diels-Alder (DA) reactions of neutral imines. These reactions are low endo selective as a consequence of the cationic character of the TSs, but highly regioselective. Solvents have poor effects on the relative energies, and an unappreciable effect in the geometries. In dichloromethane the activation energies increase slightly as a consequence of the better solvation of the iminium cations than the cationic TSs. ELF topological analysis of the bonding changes along the I-DA reactions shows that they are very similar to those in polar DA reactions. The present MEDT study makes it possible establishing that the global electron density transfer (GEDT) taking place at the TSs of I-DA reactions, and not steric (Pauli) repulsions such as have been recently proposed, are responsible for the features of these type of DA reactions.

Li⁺-conducting polyethylene oxide-based membranes, incorporating the N-butyl-N-methylpyrrolidinium bis(trifluoromethanesulfonyl)imide, are as electrolyte separators for all-solid-state lithium polymer batteries operating at medium-high temperatures. The incorporation of the ionic liquid remarkably improves the thermal, ion-transport and interfacial properties of the polymer electrolyte, which, in combination with the wide electrochemical stability even at medium-high temperatures, allow high current rates without any appreciable lithium anode degradation. Battery tests carried out at 80 °C have shown excellent cycling performance and capacity retention even at high rates, never tackled by ionic liquid-free polymer electrolytes. No dendrite growth onto the lithium metal anode was observed.

Dynamic tribochemical processes for dicationic ionic liquid containing a germinal imidazolium cation head groups bridged by a poly(ethylene glycol) and bis(trifluoromethylsulfonyl)imide anion were studied using time-resolved Mechanically Stimulated Gas Emission Mass-Spectrometry (MSGE-MS). In comparison with similar monocationic imidazolium ionic liquids with short alkylic or long polyether side chains the dicationic ionic liquid had lower coefficient of friction on Ti6Al4V alloy and smoother behaviour. The analysis of volatile decomposition products suggested multiple tribochemical reactions in which both anionic and cationic moieties are involved. Tribochemical degradation of cations was mainly through detachment of the side and bridging chains from the imidazolium head groups. Absence of volatile products containing nitrogen implies that imidazole group remained unchanged. Hydrogen and water desorption were attributed to the reactions of hydrogen fluoride being a product of anion degradation with titanium and titanium oxide.

Doubly-fed induction generators (DFIG) find extensive application in variable-speed wind power plants, providing notable advantages such as cost-effectiveness, operational flexibility across varying speeds, and enhanced power quality. This research focuses on the control of DFIGs employed in variable-speed wind turbine configurations. A suitable mathematical model is chosen for representative systems following a comprehensive review of contemporary research. Subsequent analysis reveals the instability of the open-loop time response of the system. To address this instability, the initial approach involves the implementation of the conventional Model Predictive Controller (MPC). However, the outcomes indicate that this controller falls short of delivering satisfactory performance despite the enhanced stability. In the subsequent phase, efforts are made to mitigate the impact of wind input variability by utilizing the Kalman filter, given its effectiveness in handling high variability. Following this, a novel methodology is introduced, which combines nonlinear MPC with the Lyapunov function. This method is based on the nonlinear model of the system. By using the Lyapunov function in the nonlinear MPC structure, the stability of the designed controller is guaranteed. The simulation results conducted using MATLAB software show that the output variables of the modeled DFIG system achieve stability within a reasonable timeframe applying the input.

In this paper, a small wind power generator is proposed with a new straight shape stator and rotor. The advantages of the proposed structure are introduced through a comparison between the basic and the proposed models. By comparing the pole slot combination of the proposed generator, the combination with optimal cogging torque characteristics was selected. The electromagnetic characteristics of proposed shape are analyzed for design variables using a finite element analysis (FEA) of ANSYS Maxwell. The final model of the proposed structure is designed by considering cogging torque and the generator electromagnetic characteristics. The electromagnetic and structural simulations of the final model are performed to satisfy the required performance of generator and mechanical safety. To verify the FEA results of the final model, a prototype is manufactured, experimented, and compared with the FEA results.

For offshore wind power generation, accessibility is one of the main factors that has great impact on operation and maintenance due to constraints on weather conditions for marine transportation. This paper presents a framework to explore the accessibility of an offshore site. At first, several maintenance types are defined and taken into account. Next, a data visualization procedure is introduced to provide an insight into the distribution of access periods over time. Then, a rigorous mathematical method based on finite state Markov chain is proposed to assess the accessibility of an offshore site from the maintenance perspective. A five-year weather data of a marine site is used to demonstrate the applicability and the outcomes of the proposed method. The main findings show that the proposed framework is effective in investigating the accessibility for different time scales and is able to catch the patterns of the distribution of the access periods. Moreover, based on the developed Markov chain, the average waiting time for a certain access period can be estimated. With more information on the maintenance of an offshore wind farm, the expected production loss due to time delay can be calculated.

Solar and wind resources available for power generation are subject to variability due to meteorological factors. Here, we use a new global climate reanalysis product, Version 2 of the NASA Modern-Era Retrospective Analysis for Research and Applications (MERRA-2), to quantify interannual variability of monthly-mean solar and wind resource from 1980 to 2016 at a resolution of about 0.5 degrees. We find an average coefficient of variation (CV) of 11% for monthly-mean solar radiation and 8% for windspeed. Mean CVs were about 25% greater over ocean than over land, and, for land areas, were greatest at high latitude. The correlation between solar and wind anomalies was near zero in the global mean, but markedly positive or negative in some regions. Both wind and solar variability were correlated with values of climate modes such as the Southern Oscillation Index and Arctic Oscillation, with correlations in the Northern Hemisphere generally stronger during winter. We conclude that reanalysis solar and wind fields could be helpful in assessing variability in power generation due to interannual fluctuations in the wind and solar resource. Skillful prediction of these fluctuations seems to be possible, particularly for certain regions and seasons, given persistence or predictability of climate modes with which these fluctuations are associated.

Salt stress is one of the most severe environmental stresses limiting the productivity of crops, including rice. However, there is a lack of information on how salt-stress sensitivity varies across different developmental stages in rice. In view of this, a comparative evaluation of contrasting rice varieties CSR36 (salt tolerant) and Jaya (salt sensitive) was conducted, wherein NaCl stress (50 mM) was independently given either at seedling (S-stage), tillering (T-stage), flowering (F-stage), seed-setting (SS-stage) or throughout the plant growth, from seedling till maturity. Except for S-stage, CSR36 exhibited improved NaCl stress tolerance than Jaya, at all other tested stages. Principal component analysis (PCA) revealed that the improved NaCl stress tolerance in CSR36 coincided with enhanced activities/levels of enzymatic/non-enzymatic antioxidants (root ascorbate peroxidase for T- and S+T stages and root catalase for F-, S+T and S+T+F-stages) and higher accumulation of osmolytes (shoot proline for F-stage and S+T+F-stage), indicating better antioxidant capacitance and osmotic adjustment, respectively. In contrast, higher shoot accumulation of Na+ and consequent increase in Na+/K+, Na+/Ca+2 and Na+/Mg+2 ratio in root and shoot, were identified as major variables associated with NaCl stress induced growth reduction in Jaya. In addition, CSR36 exhibited higher levels of Fe3+, Mn2+ and Co3+ and lower Cl- and SO42-, suggesting its potential to discriminate essential and non-essential nutrients, which might contribute to NaCl stress tolerance. Taken together, the findings provided the frame-work for stage-specific salinity responses in rice, which will facilitate crop-improvement programs for specific ecological niches including the coastal regions. Rice, salt stress, stage-specific salinity, antioxidant defense, ionic homeostasis, salt tolerance

Soil sodicity is a major constraint to seedling emergence and crop production, potentially reducing plant growth due to physical and chemical constraints. Examining responses to ion imbalances may assist in the identification of genotypes tolerant to chemical constraints in sodic soils and improve productivity. We evaluated the performance of four wheat (Triticum aestivum. L) genotypes in solutions with five sodium adsorption ratios (SARs) ranging from 0 to 60. For all four genotypes, seedling emergence and shoot dry matter (DM) decreased significantly with increasing SAR. A significant positive correlation was observed between Ca concentration in roots, as well as both root and shoot DM for all genotypes. At SAR values &gt;20, a more tolerant genotype (EGA Gregory), had higher Ca concentrations in root tissues, while a more sensitive genotype (Baxter) exhibited Na-induced Ca deficiency. Thus, selection for genotypes that are able to accumulate Ca in roots in sodic conditions may be a useful trait for selecting genotypes tolerant of soils with high ESP values. However, for soils that restrict plant growth at ESP (SAR) values of 6-10%, it is likely that growth is restricted by physical constraints rather than by a Na-induced Ca deficiency.

The (benzylthio)acetic acid (HBTA) and some aminopyrimidines, namely 2-aminopyrimidine (2-AP), 5-aminopyrimidine (5-AP), 2-amino-4,6-dimethylpyrimidine (2-A-4,6-DMP) and 2,4,6-triaminopyrimidine (2,4,6-TAP), were successfully embodied as structural units into the construction of a total of four novel supramolecular organic frameworks. The received crystalline solids were inspected by single crystal X-ray diffraction (SC XRD) in order to obtain insight into the structural and supramolecular facets. The SOFs deriving from 2-AP, 5-AP as well as 2-A-4,6-DMP crystallize in the form of true co-crystals (1-3), while the one originating from 2,4,6-TAP crystallizes as salt solvate (4). The SC XRD results indicated the different contents of structural residues present in the asymmetric units of the crystals 1-4 despite the using the same molar ratio of molecular co-formers in each case. The molecular structures of co-crystals 1-3 consist of either one neutral residue of each starting components (1 and 3) or a half nonionized residue of aminopyrimidine ingredient and one neutral residue of acidic specie (2). The asymmetric unit of salt solvate 4 is composed of two ionized residues of each co-former (two 2,4,6-TAP+ cations and two BTA- anions) and one MeOH solvent molecule. The most extensive H-bonding network is observed in the crystal structure of salt solvate 4. The relevant molecular ingredients in co-crystals 1-3 are mainly hold together by the neutral Ocarboxylic–H···Npyrimidine and Namine–H···Ocarboxylic H-bonds. In the case of aggregate 4, the corresponding ionic residues are predominantly sustained by the charged-assisted Npyrimidinium–H···Ocarboxylate and Namine–H···Ocarboxylate hydrogen interactions. The MeOH solvent incorporated into the crystal lattice of adduct 4 is also involved in H-bonding by simultaneously serving as the single donor in OMeOH–H···S and the single acceptor in Namine–H···OMeOH H-bonds afforded the structural diversity within the 2,4,6-TAP+ cations and BTA- anions. Other weaker sets of additional non-covalent contacts existing in the crystal structures of analyzed conglomerates are involved in the self-assembly, stabilization and expansion of total supramolecular organic frameworks. The fact of the formation of non-covalent bonded supramolecular organic frameworks in question is also reflected in corresponding results obtained through elemental analysis (EA), Fourier transform infrared spectroscopy (FT−IR) and thermal analysis (TG/DSC).

In this paper, we considered two phenomena in acoustically excited aqueous solutions of a strong electrolyte. These are the well-known Debye ionic vibrational potential (IVP), and radiofrequency anisotropy we discovered earlier , apparently, for the first time. Since both occur due to the accelerated motion of the solution, we have tried to combine them in one simple model. We have established that for a polarized UHF radio wave passed through a NaCl aqueous solution excited by an acoustic pulse the rotation angle of its vector E is proportional to the integral of the square of the observing IVP over time. An equivalent electrical circuit simulating the observed phenomena has been proposed and tested for physical feasibility. Several arguments are given in favour of the fluid-gyroscopic mechanism of RF anisotropy-related effects. We also found out that the IVP is practically independent of the vibrational velocity for frequencies below 10 kHz and it tends to zero at zero frequency. The latter is consistent with the law of conservation of energy but contradicts the incomplete existing theory.

Ionic liquids have been recognised as interesting solvents applicable in the efficient lignocellulosic biomass valorisation, especially in the biomass fractionation into individual polymeric components or direct hydrolysis some of biomass fractions. Considering the chemical character of ionic liquids, two different approaches, paved the way for a fractionation of biomass. The first strategy integrated a pre-treatment, hydrolysis and conversion of biomass through the employment of hydrogen-bond acidic 1-ethyl-3-methyimidazolim hydrogen sulfate ionic liquid. The second one relied on the use of a three-step fractionation process with hydrogen-bond basic 1-ethyl-3-methylimidazolium acetate to produce high purity cellulose, hemicellulose and lignin fractions. The proposed approaches were scrutinised for wheat straw and eucalyptus residues. Those different biomasses allowed understanding that enzymatic hydrolysis yields are dependent on the crystallinity of pre-treated biomass. The use of acetate based ionic liquid allowed to change crystalline cellulose I to cellulose II and consequently enhanced glucan to glucose yield to 93.14.1 mol% and 82.91.2 mol% for wheat straw and eucalyptus, respectively. Whereas for hydrogen sulfate ionic liquid, the same enzymatic hydrolysis yields were 61.6  0.2 mol% for wheat straw and only 7.90.3 mol% for eucalyptus residues. These results demonstrate the importance of either ionic liquid character or biomass type on the efficient biomass processing.

A systematic study has been conducted on barbiturate complexes of all five alkali metals Li–Cs prepared from the metal carbonates or hydroxide in aqueous solution without other potential ligands present, varying the stoichiometric ratio of metal ion to barbituric acid (BAH). Eight polymeric compounds (two each for Na, K, and Rb and one each for Li and Cs) have been characterised by single-crystal X-ray diffraction. All contain some combination of barbiturate anion BA− (necessarily in a 1:1 ratio with the metal cation M+), barbituric acid, and water. All organic species and water molecules are coordinated to the metal centres via oxygen atoms as either terminal or bridging ligands. Coordination numbers range from 4 (for the Li complex) to 8 (for the Cs complex). Extensive hydrogen bonding plays a significant role in all the crystal structures, almost all of which include pairs of N–H…O hydrogen bonds linking BA− and/or BAH components into ribbons extending in one dimension. Factors influencing the structure adopted by each compound include cation size and reaction stoichiometry as well as hydrogen bonding.

As one of the fastest-growing new energy sources, wind power technology has attracted widespread attention from all over the world. In order to improve the quality of wind power generation, wind speed prediction is an indispensable task. In this paper, an error correction based Variational Mode Decomposition and Broad Learning System (VMD-BLS) hybrid model is proposed for wind speed prediction. First, the wind speed is decomposed into multiple components by the VMD algorithm, and then an ARMA model is established for each component to find the optimal number of sequence divisions. Second, the BLS model is used to predict each component, and the prediction results are summed to obtain the wind speed forecast value. However, in some traditional methods, there is always time lag, which will reduce the forecast accuracy. To deal with this, a novel error correction technique is developed by utilizing BLS. Through verification experiment with actual data, it proves that the proposed method can reduce the phenomenon of prediction lag, and can achieve higher prediction accuracy than traditional approaches, which shows our method’s effectiveness in practice.

new subsonic blower wind tunnel design has been studied both numerically and experimentally, it is also referred to as “blower” wind tunnel. This paper, is initially aimed to address each sequential stage of the wind tunnel design process. Rather than applying the standard method of modelling solely the flow in the test section, a large-scale CFD model of the whole wind tunnel was employed. The loss of every constituent element was calculated and then all the losses are added up to determine the power needed for the wind tunnel operation which is used as “intake fan” boundary conditions in the CFD model. Then, flow uniformity and turbulent intensity measurements in an empty test section using a Pitot-static tube and hot wire anemometer (HWA) were introduced to validate the CFD results. The results showed that flow quality was significantly affected by boundary layer controllers (honeycomb and mesh screens) in the settling chamber and wide-angle diffuser. Investigations were also conducted to evaluate the flow deficit in the wake area behind a convex hump model using HWA. This was additional experimental tests carried out to validate the suitability of the wind tunnel flow aerodynamic research.

In April 2019, a team of Keio University and Bucknell University students was assembled to participate in Ericsson Innovation Awards with a novel concept for generating renewable energy. This conceptual system consists of a vertical axis wind turbine, a crossflow marine hydrokinetic turbine, a floating platform integrated with a quadcopter system, and three to four temporary mooring lines with ship-type anchors. The proposed designed aims to offer solutions to two current problems of floating offshore wind energy: high construction cost of floating platforms and difficulties in maintenance of mooring lines. The combination of two vertical-axis turbines into a single floating platform would enable the system, namely ESwift, to extract energy from both wind and current resources. Additionally, due to the utilization of vertical axis turbines, the center of gravity of the proposed concept is significantly lower with respect to water level, compared to that of existing floating horizontal axis wind turbines, which would potentially reduce the floater's size and construction cost. Lastly, the integrated quadcopter mechanism would assist the floater in terms of stability and mobility, and enables an array of ESwifts to automatically rearrange for maximal energy generation. The authors hope that readers would find the idea described in this open access letter worth pursuing and would further develop and commercialize the ESwift concept.

Because of the near-term risk of extreme weather events and other adverse consequences from climate change, and, at least in the longer term, global fossil fuel depletion, there is world-wide interest in shifting to noncarbon energy sources, especially renewable energy (RE). Because of possible limitations on conventional renewable energy sources, researchers have looked for ways of overcoming these shortcomings by introducing radically new energy technologies. The largest RE source today is bioenergy, while solar energy and wind energy are regarded as having the largest technical potential. This paper reviews the literature on proposed new technologies for each of these three RE sources: microalgae for bioenergy, photolysis and airborne wind turbines. The main finding is that their proponents have underestimated the difficulties facing their introduction on a very large scale.

We describe electron temperature measurements in the SSX MHD wind tunnel using two different methods. First, we estimate T_e along a chord by measuring the ratio of the C__III 97.7 nm to C_IV 155 nm line intensities using a vacuum ultraviolet monochrometer. Second, we record a biasing scan to a double Langmuir probe to obtain a local measurement of T_e. The aim of these studies is to increase the Taylor state lifetime, primarily by increasing the electron temperature. Also, a model is proposed to predict magnetic lifetime of relaxed states and is found of predict the lifetime satisfactorily. Furthermore, we find that proton cooling can be explained by equilibration with the electrons.

The wind observations for multiple levels (40–200 m) have been conducted for a long time (2016–2020) on Jeju Island of South Korea. This study aims at understanding the vertical and temporal characteristics of lower atmosphere. Jeju Island is a region located at mid-latitude and is affected by seasonal monsoon wind. The maximum wind speed appears in the lower layer during day time and is delayed in the upper layer during latter time in diurnal cycle. In summer season, the surface layer increases up to 160 m during day time via dominant solar radiation effect, which is higher than those for other seasons. However, the maximum wind speed in winter season appears irregularly among altitudes, and the surface layer is ~100 m, which is lower than that in summer season. It can be attributed to the increase in the mean wind speed in diurnal cycle caused by the strong northwestern wind for winter season. These results imply that the relationship between near-surface and higher altitudes is primarily affected by solar radiation and seasonal monsoon winds. These results are expected to contribute to site selection criteria for wind farms and to the assessment concerning planetary boundary layer modeling.

Investments in wind and solar power are driven by the aim to maximize the utilization of renewable energy (RE). This results in an increased concentration of wind farms at locations with higher average wind speeds and of solar panel installations at sites with higher average solar insolation. This is unfavourable for energy suppliers and for the overall economy when large power output fluctuations occur. Thus, when evaluating investment options for spatially distributed RE systems, it is necessary to model resource fluctuations and power output correlations between locations. In this paper, we propose a methodology for analyzing the spatial dependence, accurate modeling, and forecasting of wind power systems with special consideration to spatial dispersion of installation sites. We combine vine-copulas with the Kumaraswamy distribution to improve accuracy in forecasting wind power from spatially dispersed wind turbines and to model solar power generated at each location. We then integrate these methods to formulate an optimization model for allocating wind turbines and solar panels spatially, with an end goal of maximizing overall power generation while minimizing the variability in power output. A case study of wind and solar power systems in Central Ontario, Canada is also presented.

This article presents the results of studies of the structure and conductive properties of Na3Fe2(PO4)3 polycrystals synthesized by solid-phase and melt (using concentrated optical radiation) methods. It has been established that with the melt method, the synthesis of the material occurs under significantly nonequilibrium temperature-gradient conditions, which leads to the creation of deformations in the sample that contribute to an increase in ionic conductivity. The ability of the Na3Fe2(PO4)3 structure to adapt to anomalous deformations that occur under temperature-gradient conditions indicates the elasticity of the crystalline framework {[Fe2(PO4)]3-}3∞. Through a comparative assessment of the structural parameters and conductive properties of these materials, it is shown that polycrystals obtained by the melt method have a better texture and greater ionic conductivity. The advantage of this method is that the duration of the synthesis of α-Na3Fe2(PO4)3 is halved. It is concluded that this method is applicable to obtain effective polycrystals of other compositions.

The development of novel ionic liquid crystals for energy storage applications has gained significant attention in recent years due to their potential to develop the field of energy storage. Ionic liquid crystals represent a unique class of materials with high ionic conductivity and thermal stability, making them ideal candidates for use in advanced energy storage devices. This research aims to explore the fundamental properties, structure and liquid crystals performance of these novel materials, with the goal of advancing their practical application in next-generation energy storage technologies. By understanding the structure-function relationship of ionic liquid crystals, researchers can tailor their properties to meet specific energy storage requirements, such as high energy density, fast charging capabilities, and long cycle life. This study seeks to contribute to the growing body of knowledge in the field of energy storage by investigating the potential of novel ionic liquid crystals as efficient and sustainable energy storage solutions. The two ionic liquid crystals show mesomorphic behavior and typical zwitterion characteristics that revealed by the cyclic voltammetry techniques. These materials uploaded with lithium ions for more stability and higher ionic conductivity.

In this research work, we describe the preparation process, characterization, and photo-physical studies of an ionic liquid (IL) based semiconductor Zinc Oxide (ZnO) nanoparticles synthesized by an economical wet chemical precipitation method. For the first time, an IL was synthesized with the help of a chemical reaction between triethylamine (TEA) and bromoacetic acid (BAA). A polyamide dye was prepared by a reaction between two monomers, ethylenediamine (EDA) and trimesoylchloride (TMC), under room temperature conditions. The polyamide dye was capped on ZnO nanoparticles, and the final product was divided into three different samples, A, B, and C, according to level of concentrations of IL and Polyamide dye. These samples were characterized with X-Ray Diffraction (XRD), Field Emission Scanning Electron Microscopy (FESEM), Dynamic Light Scattering (DLS) spectra, Ultraviolet-Visible (UV-Vis), and Fluorescence spectroscopies. The formation of polyamide linkages in the ionic liquid has been confirmed by a spectroscopic method using Fourier Transform Infrared (FTIR) spectroscopy. The capping of polyamide dye molecules on the surface of ZnO nanoparticles revealed two things: (i) improved UV absorption spectra and (ii) enhanced luminescence in the photoluminescence spectra. Hence, during investigations, broad absorption bands were observed at peaks 263 nm, 278 nm, and 276 nm respectively for samples A, B, and C. Further, IL was used as an electrolyte or redox mediator and polyamide as a dye material in the fabrication of ZnO Dye-Sensitized Solar Cells (DSSCs). The samples A, B, and C were used in the fabrication of photo-anode assemblies for ZnO DSSCs. The ZnO DSSCs were tested under strong simulated light at Air Mass (AM) 1.5 solar irradiations. The observed photovoltaic results shown that solar cell SCB generated a maximum power conversion efficiency (η) of 5.65%, higher than the power conversion efficiencies of solar cells SCA (3.99%) and SCC (4.46%) respectively. The Incident Photon to Current Conversion Efficiency (IPCE) spectra values of ZnO DSSCs shown a significant improvement in the incident photon to current conversion efficiency of solar cell SCB (IPCE=61%) as compared to SCC (enhanced by 6%) and SCA (enhanced by 4%). Such solar cell assemblies can be suitable for green and clean energy applications.

Antimicrobial resistance (AMR) has become a worldwide health problem. Consequently, there is a global interest in the study of the antimicrobial activity of natural compounds as an alternative to antibiotics. One of the possibilities studied during the last years is the use of bacteriophages and their derived proteins. More specifically, phage lytic proteins or endolysins are specific enzymes that cause cell lysis and can be easily produced and purified after overexpression in bacteria. However, one of the major disadvantages of these proteins is their sensitivity to some environmental conditions that can reduce their efficiency. The use of vesicles for endolysin encapsulation could help overcome this disadvantage, offering an additional protection to the protein and allowing its controlled release and long-term stability.

The intramolecular ionic Diel-Alder (IIDA) reactions of two dieniminiums have been studied within the Molecular Electron Density Theory (MEDT) at the B97XD/6-311G(d,p) computational level. ELF topological analysis of dieniminiums shows that its electronic structure can been seen as the sum of those of butadiene and ethaniminium. The superelectrophilic character of dieniminiums accounts for the high intramolecular global electron density transfer taking place between the diene and iminium frameworks at the transition state structures (TSs) of these IIDA reactions. The activation enthalpy associated to the IIDA reaction of the experimental dieniminium, 8.7 kcal·mol-1, is closer to that of the ionic Diels-Alder (I-DA) reaction between butadiene and ethaniminium, 9.3 kcal·mol-1. However, the activation Gibbs free energy of the IIDA reaction is 12.7 kcal·mol-1 lower than that of the intermolecular I-DA reaction. The strong exergonic character of the IIDA reaction, higher than 17 kcal·mol-1, makes the reaction irreversible. These IIDA reactions present a total re/exo and si/endo diastereoselectivity, which is controlled by the most favourable chair conformation of the tetramethylene chain. Electron localization function (ELF) topological analysis of the single bond formation indicates that these IIDA reactions take place through a non-concerted two-stage one-step mechanism. Finally, ELF and atoms-in-molecules (AIM) topological analyses of the TS associated to inter and intramolecular processes show the great similitude among them.

Most of the commonly used Ionic Liquids (ILs) contain bulky organic cations with suitable anions. With our COMPLET (Concept of Melting Point Lowering due to Ethoxylation), we follow a different approach. We use simple, low-toxic, cheap and commercially available anions of the type Cx(EO)yCH2COO– to liquefy presumably any simple metal ion, independently of its charge. In the simplest case, the cation can be sodium or lithium, but synthesis of Ionic Liquids is also possible with cations of higher valences such as transition or rare earth metals. Anions with longer alkyl chains are surface active and form surface active ionic liquids (SAILs), which combine properties of ionic and nonionic surfactants at room temperature. They show significant structuring even in their pure state, i.e. in the absence of water or any other added solvent.

The ionic liquid A327H+Cl- is generated by reaction of the tertiary amine A327 (industrial mixture of tri-octil and tri-decyl amines) and hydrochloric acid solutions. Further, the extraction of Au(III) by A327H+Cl- ionic liquid under various variables, including metal and ionic liquid concentrations, has been investigated. Results indicate that A327H+AuCl4- is formed, by an exothermic (ΔHº= -3 kJ/mol) reaction, in the organic solution. Aqueous ionic strength influences the formation constants values and the specific interaction theory (SIT) is used to estimate the interaction coefficient between AuCl4- and H+. Gold (III) is stripped using thiocyanate media, and from the strip solutions, gold is precipitated as gold nanoparticles.

Exogenous RNA comprises the genetic material associated with several diseases which require immediate treatment, and thus mechanisms to hinder intracellular translation and reproduction of RNA viral agents are of great importance. Applying recent developments from this lab in methods relating to the interaction of DNA with steroid hormones, cyclic compounds are presented for intermolecular binding to nucleic acids. The requirements to achieve binding with RNA nucleotide pairs are described, which involve at a minimum functional elements positioned to interact with the lateral phosphate groups for each of the RNA strands through coupling with a positively charged ion, such as Mg2+, Ca2+, or Zn2+ ions; and an intermolecular hydrogen bond with the oxygen element of uracil at the carbon two location. Additional features of the binding molecules are examined for enhancements and differentiation in binding capability and include aromatic groups that have both a structural role of steric hindrance and a functional role to stabilize the binding mechanisms. Several categories of cyclic compounds are associated to have specific binding capabilities, and the interaction of these structures with potential receptor molecules are evaluated for assessment in delivery and binding of the compound to nucleic acids.

On the system Au(III)-HCl-A324H⁺Cl^-, liquid-liquid extraction experiments were used to define the extraction equilibrium and the corresponding extraction constant, and the facilitated transport of this precious metal, from HCl solutions, across a flat-sheet supported liquid membrane was investigated, using the ionic liquid as carrier, as a function of hydrodynamic conditions, concentration of gold(III) (0.01-0.1 g/L), and HCl (0.5-6 M) in the feed phase, and carrier concentration (0.023-0.92 M) in the membrane. An uphill transport equation was derived considering aqueous feed boundary layer diffusion and membrane diffusion as controlling steps. The aqueous diffusional resistance (Δf) and the membrane diffusional resistance (Δm) were estimated from the proposed equation, being their values 241 s/cm an 9730 s/cm, respectively. The performance of the present carrier was compared against results yielded by other ionic liquids, and also it was investigated the influence that other metals had on gold(III) transport both from binary or quaternary solutions. Gold was finally recovered from receiving solutions as zero valent gold nanoparticles.

For the Philippines, a country exposed to multiple natural hazards like severe wind, sustainable development includes resiliency. Severe wind hazard is brought by tropical cyclones in the Western Pacific, known as typhoons, that frequent the Philippines. Therefore, adequately evaluating the wind hazard and its impact is crucial for sustainable building design. Acknowledging the impacts of climate change on said hazards would require adaptation to its consequences which necessitate a deeper understanding on the changing behavior of typhoons in recent years. For this study, detailed wind information from the Japan Meteorological Agency from 1977-2021, the Holland-B parameter, and the radius of maximum wind speed for each typhoon, are determined for simulation of the regional cyclonic wind field. The analysis of the Holland-B parameters, which represent the steepness of the pressure gradient and tropical cyclone convection, suggest that the Holland-B parameters have been increasing since 2011. The regional wind fields caused by the typhoons also suggest an increasing trend in severe wind hazard. Seasonality for the location of severe wind hazard is also observed, with the Southern Philippines experiencing an increase (decrease) during the Northeast (Southwest) Monsoon season, and the Northern Philippines experiencing an increase (decrease) during the Southwest (Northeast) Monsoon season.

This study involved the fabrication of a set of Aluminum ion-grafted SBA-15 utilizing ethylene-diamine and trimethylamine ionic liquids. The primary objective was to examine the impact of the fabrication environment on the physicochemical characteristics of the catalysts. Comprehensive characterization of the Al-SBA-15 catalysts was conducted using various techniques, including XRD, FTIR, surface area, pyridine FTIR, 27Al-NMR, TGA, HRTEM, and FESEM, to analyze their physicochemical characteristics. Furthermore, the acidic characteristics were examined by con-ducting potentiometric titration in a nonaqueous solvent and employing FTIR spectroscopy to an-alyze the chemisorbed pyridine. The effectiveness of the fabricated acid materials was evaluated by testing their performance in the acetic acid esterification with butanol. The findings obtained reveal that the mesostructured of SBA-15 remains intact following the successful inclusion of Al3+ ions into the silica frameworks. Additionally, a remarkable enhancement in the existence of both Bronsted and Lewis acid centers is noted due to the grafting process of Al3+ ions. At temperatures of 80°C and 100°C, the reaction in Al-SBA-15(T-120) proceeds swiftly, reaching approximately 32% and 38% conversion, respectively, within a span of 110 minutes. The excellent catalytic performance observed in the esterification reaction can be attributed to two factors: the homogeneous distribution of Al3+ ions within the SBA-15 frameworks and the acidic character of Al-SBA-15. The findings further indicate that the grafting process for incorporating Al3+ ions into the silica matrix is more efficient.

Electrochemical deposition of silicon at room temperature is problematic due to intrinsically low conductivity of the deposits. This study reports the photoelectrochemical (PEC) deposition of silicon (Si) and silicon–carbon (Si–C) layers from an ionic liquid at temperature 40 oC using silicon tetrachloride (SiCl4) as a silicon precursor. Amorphous layers are deposited on p-type silicon (p-Si), p-type gallium arsenide (p-GaAs), and aluminum–copper alloy AA2024. The semi-conductor substrates are activated by white LED illumination, which generated photoelectrons, thereby making the substrate conductive with respect to the cathodic reaction. Photoresponsive-ness of the deposits is proven by the light-induced photocurrents on an optically inactive substrate made of the alloy AA 2024. The proposed method paves the way for the electrochemical modifica-tion of semiconductors and metals with Si and Si–C structures, which are applicable in various fields, such as; batteries, anti-corrosion coatings, photovoltaics, or PEC electrodes for hydrogen production.

The influence of pH, temperature, biopolymer ratio, total concentration, and ionic concentration on the interaction between egg white protein (EWP) and chitosan (CS) was investigated through turbidity, zeta potential, and state diagram in our research. In addition, phase behavior was observed under various conditions. The turbidity of EWP remained low (turbidity&lt;0.03) and basically unchanged at a wide range of pH (4.0-8.0), while the turbidity of CS was slightly higher (turbidity&lt;0.2) after pH 7.0 than before. Moreover, under the same conditions, a sharply rising peak pattern was observed for the complex between EWP and CS. The maximum turbidity value was observed at 55°C, and the temperature had a mild effect on turbidity. The optimum EWP to CS ratio was found to be 12:1 based on the experiment of the turbidity curves and state diagrams influenced by different biopolymer mixing ratios. With the enhanced concentrations of total biopolymer, the maximum turbidity rose insignificantly above 0.1%.

This paper presents a novel adaptive fault-tolerant neural-based control design for wind turbines with unknown dynamic and unknown wind speed. By utilizing the barrier Lyapunov function in the analysis of the Lyapunov direct method, the constrained behavior of the system is provided in which the rotor speed, its variation and generated power remain in the desired bounds. In addition, input saturation is also considered in terms of smooth pitch actuator bounding. Furthermore, by utilizing a Nussbaum-type function in designing the control algorithm, the unpredictable wind speed variation is captured without requiring accurate wind speed measurement, observation or estimation. Moreover, with the proposed adaptive analytic algorithms, together with the use of radial basis function neural networks, a robust adaptive and fault-tolerant control scheme is developed without the need for precise information about the wind turbine model nor the pitch actuator faults. Additionally, the computational cost of the resultant control law is reduced by utilizing a dynamic surface control technique. The effectiveness of the developed design is verified using theoretical analysis tools and illustrated by numerical simulations on a high-fidelity wind turbine benchmark model with different fault scenarios. Comparison of the achieved results to the ones that can be obtained via an available industrial controller shows the advantages of the proposed scheme.

Wind turbines (WTs) are clean a renewable energy source that has been growing in popularity in recent years. Gearboxes are complex, expensive, and critical components of WT, which are subject to high maintenance costs and several stresses including high loads and harsh environments that can lead to failure with significant downtime and financial losses. This paper focuses on the development of a digital twin-based approach for the modelling and simulation of WT gearboxes with the aim to improve their design, diagnosis, operation, and maintenance by providing insights into their behavior under different operating conditions. Pow-erful commercial computer-aided design tools (CAD) and computer-aided engineering (CAE) software are embedded into a computationally efficient multi-objective optimization framework (modeFrontier) with the aim of maximizing the power density, compactness, performance, and reliability of the WT gearbox. This entails minimizing its weight, volume, and maximum stresses and strains achieved without compromising efficiency. The 3D CAD model of the WT gearbox is carried out using SolidWorks, the Finite Element Analysis (FEA) to obtain the stresses and strains fields are modelled using Ansys Workbench, while the multibody kinematic and dynamic system is analyzed using MSC Adams. The method has been successfully applied to different case studies to find the optimal design and analyze the performance of the WT gearboxes. Simulation results can be used to identify potential failure modes and optimize gearbox design to improve performance, extend service life and relia-bility, thereby ensuring proper operation over its lifetime and reducing maintenance costs.

Flaring in the SS 433 microquasar is dominated by outbursts from material at distances from the centre of mass of the binary system comparable to the separation of the two components. This note completes a demonstration that ejected plasma leaves the system in the region of the L_2 point, there overflowing the outer Roche lobe and giving rise to a spiral structure as it leaves the system as part of the local environment.

The growing urgency for sustainable energy solutions necessitates a deeper understanding of the environmental impacts of renewable technologies. This article aims to synthesize and analyze Life Cycle Assessments (LCA) in this domain, providing a comprehensive perspective. We systematically categorize 2,923 articles into four communities: (1) Photovoltaic systems, (2) Wind energy systems, (3) Materials for auxiliary industry of photovoltaic and wind systems, and (4) Solar thermal systems. A comparative analysis is conducted to identify methodological consistencies and disparities across these communities. The findings reveal diverse methodological approaches and a range of environmental impacts, highlighting the complexities in assessing renewable energy systems. The article underscores the significance of material selection in photovoltaic and wind systems, providing a critical overview of the current state of LCA research in renewable energy and stressing the need for standardized methodologies. It also identifies gaps in recent research, offering insights for future studies focused on integrating environmental, economic, and social considerations in renewable energy assessments.As a case study, an LCA was used to evaluate two energy supply methods for a sensor network: one connected to the public grid and another powered by a photovoltaic panel. The off-grid system, while more environmentally friendly by reducing reliance on non-renewable energy sources, posed challenges due to the high environmental impact of battery production and disposal. Integrating environmental assessments provides a robust framework for making informed decisions on sustainable technologies. The findings are critical for projects that balance technological needs with sustainability goals.

Article contents the analytical model of the drift of a separate ice field under action of wind and current, which velocities and directions can vary during time. Model takes into account the mass of ice, added mass of sea water and the effects of the wind and current on the ice field in form the friction on its upper and underwater surfaces and frontal resistance on its end (forward and backward) surfaces. Results of performed the steady wind drift of the ice fields modelling show the drift velocity exceeds considerable known velocity of a compact ice cover wind drift. Drifting ice field has the certain kinetic energy that should be released when collision with unmovable obstacle and spent on brittle breakdown of part of the ice field. Volume of formed small ice pieces (fragments of ice field) was estimated by comparison of the specific energy of the sea ice brittle destruction and the kinetic energy of drifting ice field. Article presents the results of estimation of possible volume of the ice pieces and the scales of formed piles as result of collision with an obstacle depending on initial dimensions of ice field and wind speed. Developed models and the results of computer modelling can be used to estimate the ice pile sizes near the stationary platforms and terminals on the Arctic seas.