Recently L-shaped tunneling field-effect-transistor (LTFET) has been introduced to overcome the thermal subthreshold limit of conventional metal-oxide-semiconductor field-effect-transistors (MOSFET). In this work, shortcoming of LTFET was investigated. It was found that corner effect present in LTFET effectively degrades its subthreshold slope. To get rid of corner effect a new type of device with dual material gates is presented. The new device termed as DG-LTFET gets rid of the corner effect and results in a significantly improved subthreshold slope of less than 10 mV/dec, and an improved ON/OFF current ratio over LTFET. In this work DG-LTFET was evaluated for different device parameters, and bench-marked against LTFET. This work presents an optimum configuration of DG-LTFET in terms of device dimensions and doping levels, to get the best subthreshold, ON current and ambipolar performance from the DG-LTFET.

Doping can alter the electronic and thermoelectric attributes of an organic semiconductor system. These alterations can enable viable tunable devices that have applications in temperature sensing for environmental controls. Here we demonstrate a dual-modulation organic field-effect transistor (OFET) where temperature effectively modulates the current-voltage characteristics of the OFET and gate voltage modulates the thermoelectric properties of the active layer. Poly(3-hexylthiophene-2,5-diyl) (P3HT) was utilized as the host donor polymer, iodine was utilized as the dopant acceptor molecule Finished devices were characterized by a semiconductor analyzer system with temperature controlled by two thermoelectric cooling plates. The doping of iodine in the range of 0.25% to 0.5% mole ratio with respect to the P3HT exhibited the greatest on-off ratio of the investigated dopant concentrations. Iodine doping concentrations of 0.5% mole ratio or less can greatly improve the thermoelectric properties of a binary P3HT-based system and the current-voltage performance of the dual-modulation device.

The electronic transport stability in nanodevices composed by metal/trans-polyacetylene /metal with different long length has contributed greatly for performance, homogeneity, stability, organization of the chains, reproducibility and higher conductivity. In this paper, we present an analytical study of the electronic transport characteristics from dimerized trans-polyacetylene (trans-PA) molecules containing an odd-even number of sites coupled to metal leads (left and right) in T-shaped geometry using the extended Su-Schrieffer-Heeger (SSH) model based on tight-binding Hamiltonian with the Non-Equilibrium Green´s Function (NEGF) via Heisenberg´s equation of motion and the Keldysh´s formalism. Due to the complexity of the T-shaped odd-even chain, our proposal was to test the effects on the finite-length network for three, four, five sites and furthermore foresee for 17-sites. We show how to tune dimerization strength () coupling to the parameters and T-shaped geometry of the device to which it affects the overlap integral localized at the three endpoints of the T-shaped system, making both the odd and even chains to undergo a metal-insulator transition in their electronic behavior. The results reached through control parity of the chain plane of the parameters governing () the electronic and experimental tunneling allow a better understanding of the subject.

Field-effect transistor (FET)-based biosensors stand as powerful analytical tools for detecting trace-specific biomolecules in diverse sample matrices, especially in the realms of pandemics and infectious diseases. The primary concern in applying these biosensors is their stability, a factor directly impacting the accuracy and reliability of sensing over extended durations. The risk of biosensor degradation is substantial, potentially jeopardizing sensitivity and selectivity and leading to inaccurate readings, including the possibility of false positives or negatives. This paper delves into the documented degradation of silicon nanobelt FET (NBFET) biosensors induced by buffer solutions. The results highlight a positive correlation between immersion time and the threshold voltage of NBFET devices. Secondary ion mass spectrometry analysis demonstrates a gradual increase in sodium and potassium ion concentrations within the silicon as immersion days progress. This outcome is ascribed to the nanobelt's exposure to the buffer solution during the biosensing period, enabling ion penetration from the buffer into the silicon. The study emphasizes the critical need to address buffer solution-induced degradation to ensure the long-term stability and performance of FET-based biosensors in practical applications.

Protein tyrosine sulfation (PTS), a vital post-translational modification, facilitates protein–protein interactions and regulates many physiological and pathological responses. Monitoring PTS has been difficult owing to the instability of sulfated proteins and the lack of a suitable method for detecting the protein sulfate ester. In this study, we combined an in situ PTS system with an ultra-high-sensitivity polysilicon nanowire field-effect transistor (pSNWFET)-based sensor to directly monitor PTS formation. A peptide containing the tyrosine sulfation site of P-selectin glycoprotein ligand (PSGL)-1 was immobilized onto the surface of the pSNWFET by using 3-aminopropyltriethoxysilane and glutaraldehyde as linker molecules. A coupled enzyme sulfation system consisting of tyrosylprotein sulfotransferase and phenol sulfotransferase was used to catalyze PTS of the immobilized PSGL-1 peptide. Enzyme-catalyzed sulfation of the immobilized peptide was readily observed through the shift of the drain current–gate voltage curves of the pSNWFET before and after PTS. To the best of our knowledge, this is the first study to describe in situ PTS and its direct observation by using semiconductor devices. We expect that this approach can be developed as a next generation biochip for biomedical research and industries.

We report the electrical properties of Al0.3Ga0.7N/GaN heterojunction field effect transistor (HFET) structures with a Ga2O3 passivation layer grown by metal-organic chemical vapor deposition (MOCVD). In this study, three different thicknesses of Ga2O3 dielectric layers were grown on Al0.3Ga0.7N/GaN structures leading to metal-oxide-semiconductor-HFET or MOSHFET structures. X-ray diffraction (XRD) showed the (¯201) orientation peaks of -Ga2O3 in the device structure. The van der Pauw and Hall measurements yield the electron density of ~ 4 x1018 cm-3 and mobility of ~770 cm2V-1s-1 in the 2-dimensional electron gas (2DEG) channel at room temperature. Capacitance-voltage (C-V) measurement for the on-state 2DEG density for the MOSHFET structure was found to be of the order of ~1.5 x1013 cm-2. The thickness of the Ga2O3 layer was inversely related to the threshold voltage and the on-state capacitance. The interface charge density between the oxide and Al0.3Ga0.7N barrier layer was found to be of the order of ~1012 cm2eV-1. The annealing at 900° C of the MOSHFET structures revealed that the Ga2O3 layer was thermally stable at high temperatures resulting in insignificant threshold voltage shifts for annealed samples with respect to as-deposited (unannealed) structures. Our results show that the MOCVD-gown Ga2O3 dielectric layers can be a strong candidate for stable high-power devices.

Floral nectar is a key reward in Leguminosae despite the exceptional diversity of flowers in this family. The paper aims to summarize the available data on structure, ontogeny, regulation, and possible evolution of the leguminous floral nectaries. To date, detailed characterization of ultrastructure and mode of secretion is available only for a few representative of the family whereas the majority remains understudied from this perspective. In most cases, regardless of flower symmetry, nectaries are localized between stamens and a carpel. The nectar is usually exuded from modified stomata although the exact mode of secretion by specialized parenchyma may differ between taxa. The leguminous floral nectaries often have certain features of monosymmetry with preferentially abaxial development. Nectaries were independently lost in several lineages, and equally recurrent is the emergence of substitutive, i.e. evolutionary innovative, nectar-producing structures. Floral nectaries possess a certain degree of evolutionary inertia, i.e. they remain stable even in lineages in which flower morphology underwent significant changes compared with an ancestral plan, such as shifts in merism, symmetry, organ number and alike. Due to their evolutionary stability, floral nectaries are rarely used in taxonomy of Leguminosae.

Traversal time in tunneling effect for ultrasonic waves in tapered waveguides is derived considering its analogy with quantum and electromagnetic waves tunneling. If, as traversal time, the so called phase time is considered, the ultrasonic wavepacket shows the equivalent in acoustics of superluminality i.e. the derived velocity , crosses the limit of bulk transverse ultrasonic waves in the medium of the waveguide that is the equivalent of c in the quantum and electromagnetic cases. Graphs clearly illustrating this so called Hartman effect are obtained confirming the experimental results in the three different fields.

Micro plasma devices (MPD) with power gains are of interest in applications involving operations in the presence of ionizing radiations, in propulsion, in control, amplification of high power electromagnetic waves, and in metamaterials for energy management. Here we review and discuss MPDs with an emphasis on new architectures that have evolved during the past 7 years. Devices with programmable impact ionization rates and programmable boundaries are developed to control the plasma ignition voltage and current to achieve power gain. Plasma devices with 1-10 μm gaps are shown to operate in the sub-Paschen regime in atmospheric pressures where ion-assisted field emission results in a breakdown voltage that linearly depends on the gap distance in contrast to the exponential dependence dictated by the Paschen curve. Small gap devices offer higher operation frequencies at low operation voltages with applications in metamaterial skins for energy management and in harsh environment inside nuclear reactors and in space. In addition to analog plasma devices, logic gates, digital circuits, and distributed amplifiers are also discussed.

Dynamic time history analysis is a powerful and effective method to study the seismic response of tunnels, the dynamic time history to analyze the seismic response of the tunnel in the typical subway in this paper. The analysis results show that the overall levelling of the tunnel will not affect the tunnel too much, and the seismic response of the tunnel is mainly related to the relative displacement of the ground around the tunnel. The analysis results show that the internal force of the tunnel and the tunnel inclination have a good linear relationship, and the tunnel inclination can be used to measure the magnitude of the seismic response of the tunnel.

Pigmented corn is a gramineae food of great biological, cultural and nutritional importance for many Latin American countries, with more than 250 breeds in the American continent. It confers a large number of health benefits due to its diverse and abundant bioactive compounds. In this narrative review we decided to organize the information on the nutrients, bioactive compounds and phytochemicals present in pigmented corn, as well as their effects on human health. Phenolic compounds and anthocyanins are some of the most studied and representative compounds in these grasses, with a wide range of health properties, mainly the reduction of prooxidant molecules. Carotenoids are a group of molecules belonging to the terpenic compounds, present in a large number of pigmented corn breeds, mainly the yellow ones, whose biological activity incorporates a wide spectrum. Bioactive peptides can be found in abundance in corn, having very diverse biological effects that include analgesic, opioid, antihypertensive, etc. activity. Other compounds with biological activity found in pigmented corn are resistant starches, some fatty acids, phytosterols, policosanols, phospholipids, ferulic acid and phlobaphenes, as well as a great variety of vitamins, elements, and fibers. This review aims to disseminate and integrate the existing knowledge on compounds with biological activity in pigmented corn, in order to promote their research, interest and use by scientists, nutrition professionals, physicians, industries and the general population.

The research on the excavation mechanical properties of underpass tunnels has already had certain results, but fewer of them consider the effects of dynamic and static loads on the excavation mechanical properties of underground tunnels at the same time, especially the lack of research cases of double-line highway tunnels with angled underpasses of existing railway tunnels. In this paper, based on the tunnel project of the new double-line Shiqian Highway Tunnel passing under the Hurong Railway at an oblique angle, the mechanical parameters of the rock body in the cross-tunneling area under the influence of static and dynamic load coupling are obtained by using the disturbance quantification coefficients and the Hoek-Brown criterion based on the method of over-advanced geological prediction and the investigation of the surrounding rock on the palisade face, and the engineering-scale finite element model is constructed and the mechanical characteristics of the excavation in the tunnel of the double-lane highway tunnel passing under the existing railroad under the influence of the static and dynamic loads are analyzed. The results show that: the new tunnel rock movement law for the top of the arch sinking, bottom plate bulging, side wall to move outward, the height and width of the arch and bottom plate arch with the tunnel excavation and increase, the side wall rock displacement effect is smaller; left and right lines of the tunnel disturbed area of the rule of change is similar; the existing tunnel bottom plate displacement is more than the top plate and the left and right side walls by the excavation of the time step influence is larger. Typical profile displacement is mainly determined by the distance from the excavation surface; the new tunnel in the four types of calculation conditions of the rock disturbance angle is the same; the existing tunnel roof and side wall Von Mises stress extreme occurs in the tunnel structure, the bottom plate there are pressure relief and pressure-bearing areas; based on the displacement control criteria, the recommended upper and lower step blasting method.

This letter presents a dual-frequency terahertz amplitude modulator based on a cross-shaped structure and U-shaped metal patches. Its structural unit is a typical metal-substrate structure. The top metal consists of a cross-shaped structure and U-shaped metal patches, and the bottom substrate layer is made of quartz. Amplitude modulation is achieved by adjusting the temperature of the vanadium dioxide (VO2) patches. The modulation depth can be approximately 75%. The mechanism of the resonance frequency is explained by the equivalent circuit model. The proposed structure shows good amplitude modulation capability at different incidence and azimuth angles by changing the location of the VO2 patches. The dual-frequency terahertz amplitude modulator can be used in terahertz communication, imaging, etc.

Insulated Gate Bipolar Transistor (IGBT) may convey high current and sustain high breakdown voltages; it may provide high power control. In a sense, how IGBT demonstrates the capability of power control was not specifically described, and the equivalent bipolar junction transistors (BJT) activated by an applied bias to the insulated gate is intriguing. As seen in Figure 1, IGBT shows an equivalent circuit structure containing two types of BJT, (NPN-type Bipolar transistor and PNP-type Bipolar transistor), which can be modeled as diode-associated transistor. Apparently, as a bias applies to the controlling gate, the channel beneath the gate oxide gets strongly inversed and turns out to be conductive just like what happens on metal-oxide-silicon field effect transistor (MOSFET), which provides necessary igniting currents to both BJTs and thus causes high current gain flowing through them-selves from the bottom. A proposed and renewed formula provides addressing the above scenario and successfully fitting the measured data that forms the characteristic curves. Some parameters in the proposed formula, which includes size and mobility associated constant, threshold voltage, and Early-Voltage-related lambda for MOSFET, explain and explore the underlying physics. IGBT thus enjoy high input impedance and high current gain due to MOSFET (Insulated Gate) and BJT, respectively. This formula combines both merits of MOSFET and BJT in order to fit the measured data. Indeed, the formula intimately fits IGBT electrical characteristic curves, and thus may be qualified and served as a model. The new model is then advisable for designing power integrated circuit to exactly achieve power saving, power control, and power efficiency.

By repeated unloading and loading of the excavation dynamic and static loads, repeated train dynamic and static loads of multi-factors, the underpass tunnel, cross tunnel engineering influence area rock layer, the existing tunnel structure of the three constitutes a multifaceted structure, multi-factor interaction system. Existing tunnels into the prediction theory model of the new tunnel excavation process of dynamic and static loads, dynamic and static loads of existing tunnels are mostly analyzed individually, the results of synergistic analysis needs to be improved. Based on the theory of the current layer method, the paper comprehensively considers the stiffness of the existing tunnel, the stiffness of the new tunnel, the excavation method load and the existing tunnel load, coupled with Peck's empirical formula, the theoretical model of deformation prediction for excavation of a two-lane highway tunnel under the tunnel through the existing railroad is proposed, and verified and optimized by numerical calculations and monitoring data, which proves the applicability and reliability of the theoretical model in the similar strata and the project promotion.

This paper explores indigenous perspectives on the understanding and management of cultural heritage within the Mapungubwe and Makgabeng Cultural landscapes in South Africa. State-based management system paid little attention to indigeneity resulting in contested interpretation of the archaeological past. This by-passing of indigenous input is a product of colonial and apartheid policies that glorified Western practices at the expense of black African heritage stakeholders. World heritage mechanisms are also skewed in favor of modern practice which is overly designed to be sensitive to tangible aspects of the past than the intangible elements that make up much of indigenous African heritage. We used the archaeology of Mapungubwe and Makgabeng Cultural landscapes as a test case for the impact of indigenous voices on heritage, but the results have wider applicability. We employed semi-structured interviews and focus group discussions to gather qualitative data that we calibrated with our lived experiences as products of Tsonga-speakers from this broader landscape. The results expose that indigenous people use physical manifestation of sites, ethnographic inquiry, names, oral history, spirit mediums, landscape memory, genealogy, and praise poetry to identify, interpret, evaluate, and manage their cultural heritage. Additionally, indigenous perspectives which rely on collective memory, ritual practices, and indigenous knowledge systems have huge potential for enriching our understanding of the archaeological heritage. We propose a more inclusive archaeology and heritage management practice that involve indigenous groups in the identification, interpretation, grading, and presentation of the African past.

: Tunnel instability and lining integrity are intimately tied to the creep properties of the surrounding rock. The acquisition of rock mass creep parameters is critical in ascertaining the appropriate timing for lining construction. Nevertheless, creep tests on rock specimens conducted in a controlled setting cannot be straightforwardly extrapolated to rock mass creep analysis. This study performs laboratory-based creep tests on mudstone samples and establishes the corresponding creep constitutive model. Integration of a Mohr-Coulomb element with the Burgers model in series serves to characterise the yield creep behaviour of the rock mass. Additionally, the research outlines a series of 100 orthogonal experiments utilising randomised creep parameters, and formulates a GA-BP neural network inversion model. Employing long-term deformation measurements from the crown and sidewalls of the project site, this study deduces the creep parameters of the mudstone in the investigated tunnel section and examines the prolonged deformation traits of the surrounding rock. Drawing on the deformation traits of the surrounding rock and the forces impacting the primary support and lining structures, this paper evaluates the earliest and latest viable lining casting periods and pinpoints an optimal timing interval for lining implementation. The methodologies employed herein can serve as a benchmark for analogous endeavors internationally.

A novel concrete beam-column connection utilizing L-shaped steel bars is proposed to address the growing demand for prefabricated buildings and to ensure good seismic performance in such beam-column structures. After positioning two prefabricated beams with L-shaped tendons into the designated connection points at the top and bottom of the columns, concrete is poured into the post-cast section of the joint and the composite beam area, realizing a connection between the beams and columns. Quasi-static tests were performed on four combined nodes and one cast-in-place node to investigate their failure modes and stress mechanisms. Seismic performance indices, including hysteretic curves, skeleton curves, ductility performance, and energy dissipation capacity, were analyzed. Concurrently, the finite element method (FEM) was employed for parameter analysis. By integrating the test and FEM results, an equation for calculating the shear capacity of the connection was derived. The findings demonstrate that the hysteresis curve of the newly developed prefabricated joints is relatively full, with their overall performance index comparable to that of cast-in-place joints. Additionally, enhancing the post-casting area of concrete, the length of the L-shaped bars, the concrete strength in the composite beam region, the axial compression ratio, or the steel tube dimensions can effectively improve overall performance. The derived equation for the shear-bearing capacity of the connection satisfies design and application requirements.

In the present study, the performance of a 70 L photobioreactor, operating outdoors, was investigated using a purple bacterial strain as Rhodopseudomonas sp. S16-VOGS3 for producing poly-3-hydroxybutyrate (PHB). The novel photobioreactor was equipped with 5L-shaped rows; the bottom of every row was placed in a stainless-steel tank containing water with controlled temperature. The photofermentation trials were carried out under fed-batch mode and under a semi-continuous regimen using lactic acid as carbon source. The effect of the irradiance and the C/N ratio on the PHB accumulation was investigated, in order to evaluate the optimal bacterial growth. The results showed the feasibility of the prototype photobioreactor for the production of PHB by Rhodopseudomonas sp. S16-VOGS3 under the natural light/dark cycle. During the fed-batch growth (144 h long), the cumulative PHB increased quickly reaching the maximum value of 377 mg/L and decreased to 255 mg/L during the semi-continuous regimen (336 h long).

Viscum album L., also known as “Mistletoe”, is a hemiparasitic plant native to the European continent that grows on various host trees. This plant contains a wide variety of active compounds that can be used for treat various diseases, such as diabetes, hypertension, as an anti- inflammatory and antioxidant. However, it is most indicated in human medicine for the adjuvant treatment of cancer patients. Both for its properties directed against neoplastic cells and for its antioxidant and anti-inflammatory properties. In Veterinary Medicine, I am very few studies are recorded for animals, although formulations are available for commercial use in oral and injectable form, mostly for homeopathic use. Many studies have been conducted on a large scale by groups of independent researchers and doctors in several countries, such as Switzerland, Germany and Brazil. Therefore, this review aimed to collect data on the use of Viscum album in Veterinary Medicine in order to encourage research in this sector not only in oncological diseases but in other directions in which Viscum can find use as an anti-pretensive and anti-diabetic agent. Introduction: Lectins, flavonoids, phenols such as phenylpropanoids, coumarins, sterols, lignans, terpenoids, phenylpropanoids, alkaloids, fatty acids and viscotoxins are among the main active ingredients present in the phytocomplexes of the Viscum album plant. In particular, Attention should be given to specific oligoproteins in consideration of their activity biological [1]. present in The foliage and fruits of V. album, as in other related species, contain low-weight proteins molecular type of thionin, called viscotoxins, as well as characteristic lectins, called viscolectins, both can contribute to its system defense and can be found in extracts and related products. These classes of Viscum microproteins have received considerable attention due to their contribution to effects cytotoxics and immunostimulants of mistletoe extracts used in medicine, as discussed later, including their mechanism of action [ 2–3] viscotoxins can increase the number of cells circulating naturalkillers and consequently improve the response host antitumor immunity [ 8]. Likewise, the a viscotoxin has an effective immunomodulatory impact on human and animal granulocytes [ 9, 10] and also acts on cellular apoptosis [11]. The cytotoxic action of viscotoxin is comparable to that of conventional chemotherapeutic agents [ 12].

Sudden variation of aerodynamic loads is the potential source of safety accidents of high-speed train (HST). As a follow-up investigation on the aerodynamic response of a HST that enters a tunnel under crosswind environment, this paper focuses on the transient response of a HST’s safety indices based on the train–track coupling interaction model. Firstly, a wind–train–track coupling dynamic model is proposed by introducing transient aerodynamic loads into the vehicle–track system. Secondly, the temporal evolution of safety coefficients indicates that the train’s safety risk increases during tunnel entry with crosswind. Results show that the derailment coefficients and wheel load reduction rate during tunnel entry are not only larger than those in open air but also those inside the tunnel due to the sudden disappearance of wind excitation at the tunnel entrance. In addition, the characteristic wind curve, which is the wind velocity against the train speed, is presented for application based on the current specification of the safety criteria threshold. The investigation will be useful in assessing the safety risk of a running train subjected to other aerodynamic attacks, such as the coupling effect of infrastructure scenario and crosswind in windy area.

Amidst worsening climate change, drought stress imperils global agriculture, jeopardizing crop yields and food security, necessitating urgent exploration of sustainable methods like biopriming, harnessing beneficial microorganisms to bolster plant resilience. Recent research has revealed diverse biological compounds with versatile applications produced by Schizophyllum commune, rendering this fungus as a promising contender for biopriming applications. For the first time this study aimed to investigate,the potential of S. commune exo- (EPSH) and intra-PSH (IPSH), isolated from two strains: Italian (ITA) and Serbian (SRB) under submerged cultivation, in enhancing the resilience of Pisum sativum L. seeds through biopriming technique. Testing of seed quality of bioprimed, hydroprimed, and unprimed seeds was done using a germination test, under optimal and drought conditions. In optimal conditions, the IPSH SRB increased germination energy by 5.50% compared to the control, while the highest percentage of germination (94.70%) was shown after biopriming with PSH isolated from the ITA strain. Additionally, all assessed treatments resulted in a boost in seedling growth and biomass accumulation, where the ITA strain demonstrated greater effectiveness in optimal conditions, whereas the SRB strain showed superiority in drought conditions. The drought tolerance indices increased significantly in response to all examined treatments during the drought, with EPSH ITA (23.00%) and EPSH SRB (24.00%) demonstrating the greatest effects. Results demonstrate a significant positive influence of fungal PSH, indicating their potential as biopriming agents and offers insights into novel strategies for agricultural resilience in the face of changing environmental conditions.

In eastern part of Ethiopia groundnut is very commonly intercropped with sorghum. Even though intercropping of sorghum with groundnut is practiced in the eastern part of Ethiopia the population density at what ratio should not be known. Therefore determining the population ratio is found to be crucial to draw management options. The study was conducted at two locations at Fadis (on station) and Babile (sub- station). Sorghum variety (Teshale) and groundnut (Fetene) were used as planting materials. All agronomic data were collected and analyzed by using GenStat software. Significant different were obtained among the treatments. The research result showed that, there were significance difference for both sorghum and ground nut yield per hectare in the years (2014 and 2015) among treatments. The result over time(in 2014 and 2015) at Fadis and Erer showed that the highest sorghum and groundnut yield per hectare were obtained/harvested from the intra row spacing of 25cmx20cm and 30cmx20cm intercropping sorghum with ground nut system with (1.27 and 1.31) respectively. The highest LER (1.31) and highest GMV (10218.00 ETBr/ha) were obtained from the intercropping of 30cmx20cm (Sorghum & groundnut). Clearly showed that, with intercropping of sorghum and Groundnut, it is possible to produce additional yield of sorghum without significant reduction in groundnut yield. As a result of this, the intra spacing of the main crop (sorghum) 25cm and 30cm and for the subsidiary crop (groundnut) 20cm was recommended for further production in the study areas of eastern Harerghe zone and similar agro-ecologies.

Tunnel-interchange connecting sections pose significant safety challenges on mountainous expressways due to their high incidence of accidents. Improving road safety necessitates a comprehensive understanding of driver behavior in such areas. This study explores the influences of road characteristics, signage information volume, and traffic conditions on drivers' car-following and lane-changing behavior in tunnel-interchange diverging areas. Utilizing driving data from 25 subjects of 72 simulated road models, driving performance is assessed using Friedman rank test and multivariate variance analysis. The results highlight the significant influence of both connection distance and signage information load on driving behavior. In tunnel-interchange scenarios, the reduction of velocity increased by 62.61%, and speed variability surged by 61.11%, indicating potential adverse effects on driving stability due to the environmental transitions. Decreased connection distances are associated with reduced lane-changing durations, larger steering angles, and increased failure rates. Furthermore, every two units increase in signage information leads to a 13.16% rise in maximum deceleration and a 5% increase in time headway. Notably, the signage information volume shows a significant interaction with connection distance (F=1.60, P=0.045) for most car-following indicators. Hence, the study recommends a maximum connection distance of 700 m and signage information not exceeding nine units for optimal safety and stability.

Research shows that in earthquakes the ground response changes in areas where there are underground cavities. Due to the fact that subways and underground tunnels pass from beneath buildings in urban areas, these changes in ground response have a direct impact on the seismic behavior of structures. In this study, first by model validity and reliability of the results, steel structures modeling was conducted and steel structure behavior was evaluated due to Tunnel-Soil-Structure seismic interaction. Parameters studied are number of stories, soil type, tunnel depth, horizontal tunnel-structural distance and dynamic loading. Considering that one of the most important parameters of structural control is drift and story displacement, so this important factor will be considered. The results show that tunneling has a direct effect on the rate of structural displacement and increases the structural response. Also, the behavior of the structure is affected by the position of the structure at the ground level and the position of the tunnel and this should be considered during the design phase of the structures.

Mulberry leaves are a classic herb commonly used in traditional Chinese medicine, and experience since ancient times has shown that leaves collected after frost have better medicinal properties. However, the characteristics of the changes of critical metabolic components in mulberry leaves, especially Morus nigra L., are still unknown. To further study the influence of harvesting time on the dynamic changes of metabolites, especially DNJ compounds and flavonoids, in mulberry leaves after frost. We used metabolomics technology to select 100+ metabolites as indexes to reflect the dynamic changes of metabolites in mulberry leaves comprehensively. The results showed significant differences in the effects of defrosting on the accumulation of metabolites in the leaves of Morus nigra L. and Morus alba L. The content of DNJ in the leaves of Morus nigra L. showed a decreasing trend after the frost, while flavonoids reached the peak of the second frost. For Morus alba L, DNJ showed an increasing trend after frost, especially reaching its peak one day after the second frost. Flavonoids mainly peak in the week before the frost. In addition, by analyzing the influence of picking time on metabolite accumulation in two mulberry leaves, it was concluded that higher DNJ alkaloids and flavonoids would be obtained in mulberry leaves collected in the morning. This study also provides scientific guidance for the optimum harvesting time of mulberry leaves.

Railway has been used as one of the most crucial means of transportation in public mobility and economic development. For efficiently operating railways, the electrification system in railway infrastructure, which supplies electric power to trains, is essential facilities for stable train operation. Due to its important role, the electrification system needs to be rigorously and regularly inspected and managed. This paper presents a supervised learning method to classify Mobile Laser Scanning (MLS) data into ten target classes representing overhead wires, movable brackets and poles, which are recognized key objects in the electrification system. In general, the layout of railway electrification system shows a strong regularity of spatial relations among object classes. The proposed classifier is developed based on Conditional Random Field (CRF), which characterizes not only labeling homogeneity at short range, but also the layout compatibility between different object classes at long range in the probabilistic graphical model. This multi-range CRF model consists of a unary term and three pairwise contextual terms. In order to gain computational efficiency, MLS point clouds is converted into a set of line segments where the labeling process is applied. Support Vector Machine (SVM) is used as a local classifier considering only node features for producing the unary potentials of CRF model. As the short-range pairwise contextual term, Potts model is applied to enforce a local smoothness in short-range graph. While, long-range pairwise potentials are designed to enhance spatial regularities of both horizontal and vertical layouts among railway objects. We formulate two long-range pairwise potentials as the log posterior probability obtained by Naïve Bayes classifier. The directional layout compatibilities are characterized in probability look-up tables which represent co-occurrence rate of spatial relations in horizontal and vertical directions. The likelihood function is formulated by multivariate Gaussian distributions. In the proposed multi-range CRF model, the weight parameters to balance four sub-terms are estimated by applying the Stochastic Gradient Descent (SGD). The results show that the proposed multi-range CRF can effectively classify detailed railway elements, representing the average recall of 97.66% and the average precision of 97.07% for all classes.

In this paper, we investigate the Hawking radiation process by using the quantum tunneling phenomenon of massive spin-1 (W-bosons) and spin-0 particles from (2+1) dimensional Black Hoke with quintessential and magnetic field. For this purpose, using Hamilton-Jacobi ansatz, we apply the WKB approximation to the field equations of massive charged vector particles. We get the required tunneling rate of radiated particles and obtain their corresponding Hawking temperature $T_h$. In order to study the quantum gravity effects, we utilize the generalized Proca and Klein-Gordan equations incorporating the generalized uncertainty principle (GUP) and recover the accompanying quantum corrected temperature $T'_{h}$.

This study introduces a gate design that uses pass transistor switches and enables the implementation of all nec- necessary logic gates with a single structure. This gate design can be used for efficient circuit resizing and creating secure obfuscated circuits. This work also presents simulation results that demonstrate the effectiveness of the gate in performing various logic gate operations.

Protrusive defects on the color filter of thin-film transistor (TFT) liquid crystal displays (LCDs) frequently damage the valuable photomask. An fast method using side-view illuminations associated with digital charge-couple devices (CCDs) to detect the protrusive defect in the four substrates, which are the black matrix (BM), red, green, and blue. Between the photomask and substrate, the depth of field (DOF) is normally 300 μm for the proximity-type aligner; we select the four substrates to evaluate the detectability in the task. The experiment is capable of detecting measurements of 300 μm and even lower than 100 μm can be assessed successfully. The maximum error of the measurement is within 6% among the four samples. Furthermore, the uncertainty analysis of three standard deviations is conducted. Thus, the method is cost-effective to prevent damage for valuable photomasks in the flat panel display industry.

Light sources tend to affect images captured in any automatic optical inspection (AOI) system. In this study, the effectiveness of metal-halide lamps, quartz-halogen lamps, and LEDs as the light sources in AOI systems for the detection of the 3rd and 4th layers electrodes of thin-film-transistor liquid crystal displays (TFT-LCDs) is examined experimentally. The results show that the performance of LEDs is generally comparable or better than that of metal-halide and quartz-halogen lamps. The best optical performance is by the blue LED due to its spectrum compatibility with the time-delay-integration charged-coupled device (TDI CCD) sensor and its better spatial resolution. The images revealed by the blue LED are sharper and more distinctive. Since current LEDs are more energy efficient and environmentally friendly, using LEDs as the light source for AOI is very beneficial. As the blue LED performs the best, it should be adopted for AOI using TDI CCD sensors.

Forest-grass intercropping patterns of protected cultivation has been widely used to increase productivity and sustainability in modern agriculture. However, there have been few studies of wolfberry (L. barbarum) intercropping and it is cultivated mostly by clean tillage. This paper takes 10 kinds of wolfberry-forage intercropping patterns, compares the effects of different planting modes on the growth, yield, photosynthetic characteristics, nutritional quality, and the degree of occurrence of diseases and pests, which aims to make clear the effects of wolfberry-forage intercropping patterns on wolfberry. The results showed that different intercropping combinations had different effects on wolfberry. The overall effect of Wolfberry-forage intercropping patterns on the growth of wolfberry were promote the photosynthetic characteristics. Ryegrass could increase the branch number, Lvyuan 5 and mangel increase branch length; Mangel, clover, sweet sorghum, ryegrass and stipas could reduce the damage of powdery mildew by 69%, and alfalfa, stipa and ryegrass could reduce the occurrence of aphids by 67% (P<0.05). Intercropping could increase carotenoids, flavonoids and ascorbic acid contents to improve wolfberry quality by 21%, 53% and 127%, respectively (P<0.05). Among all the performances, wolfberry-mangel intercropping has absolute advantages in promoting wolfberry yield and quality increase. Therefore the best patterns of wolfberry-mangel, wolfberry-ryegrass, wolfberry-alfalfa and wolfberry-clover were chosen.

In this project, four of fibers Bragg gratings were fabricated by injecting different volumes of liquids (star line Glass Mechanix optical adhesive material, olive oil diluted with ethanol) into the hollow core fiber. The amplitude splitting interferometric technique with a high resolution specially designed translation stage was used for the fabrication process. The fabrication was done using ultraviolet laser operated at wavelength 405nm. The fabricated Bragg length of the four fibers is equal to 3.8 cm. The results presented fiber Bragg grating (FBG) with successful fabrication at 653.3 nm Bragg reflected wavelength.

This study focuses on the potential medicinal properties of Campsis radicans L. extracts and its aim is to investigate the antioxidant and antiproliferative effects of these extracts on the human colon adenocarcinoma cell line (HT-29). Cytotoxic activity in the HT-29 cell line was evaluated, and the 3-dimensional structures of phenolic compounds were obtained using the GC-MS method. Docking simulations were performed with AutoDock Vina, targeting proteins that are crucial in the apoptotic pathway (Bax, Bcl-2, and Caspase-3). Drug similarities and ADMET estimates of the phenolic compounds were obtained from databases. The highest antioxidant activity of Campsis radicans L. plant was observed in ethanol and water extracts, with notable inhibition capacities. While the total phenolic content was highest in ethanol, water, and ether extracts respectively the total flavonoid content was highest in ethanol, then ether, and water extracts. Certain elements were undetectable in mineral determination, and others exceeded the toxic doses for plants. The water extract exhibited dose-dependent cytotoxic activity in the HT-29 cell line, with an IC50 value of 4.47 mg/mL. Molecular docking results revealed the binding of phenolic molecules to the active sites of apoptotic pathway proteins. The findings suggest that Campsis radicans L. plant possesses cytotoxic properties, significant phenolic and flavonoid content, and a high antioxidant capacity. These properties make it a potential candidate for treatment use, emphasizing its potential therapeutic value in the HT-29 cell line. Further research and exploration on the identified phenolic compounds could contribute to the development of novel therapeutic agents.

Wind tunnels are devices that enable researchers to study the flow over objects of interest, the forces acting on them and their interaction with the flow, which is nowadays playing an increasingly important role due to noise pollution. Since the first closed circuit wind tunnel with variable cross-section was built in G¨ottingen, its Prandtl configuration has little change. The wind tunnel with Prandtl configuration has four corners and vanes, more than 50% of the total pressure loss are caused by the corners and vanes. How to reduce the total pressure loss is a world class problem in the wind tunnel design. This study attempts to propose a novel configuration of wind tunnel, where the corners have been replaced by semi-circular tunnel. Sun wind tunnel 2 has only two corners and vanes, while Sun wind tunnel 1 has no corners and vanes at all. It is expected the new wind tunnel can reduce the total pressure loss from 50% to 10%.

African trypanosomes are an early branch in eukaryotic evolution and developed a unique endomembrane system as an adaptation to their parasitic life style. The key virulence mechanism of many pathogens is successful immune evasion to enable survival within the host, which is a feature requiring both genetic events and membrane transport in African trypanosomes. Intracellular trafficking not only plays a role in immune evasion, but also in homeostasis of intracellular and extracellular compartments and interactions with the environment. Significantly, historical and recent work has unravelled some of the connections between these processes and highlighted how immune evasion mechanisms associated with adaptations in membrane trafficking may have, paradoxically, provided specific sensitivity to drugs. Here we explore these advances in understanding the membrane composition of the trypanosome plasma membrane and organelles and provide a perspective for how transport could be exploited for therapeutic purpose.

CONTEXT: The sustained White corn (Zea mays L.) yield relies on supply of Nitrogen (N), which is an important element in improving soil fertility. OBJECTIVE: The research aim to determine the effect of Nitrogen on white corn yield and grain mass. METHOD: The experimental design was a 4 × 4 factorial arranged in randomized complete block design with 2 replications each. The effect of nitrogen was determined in terms of the flow within the soil, initial component, addition, uptake, loss and use of nitrogen by the White corn plants. Nitrogen was applied as Granular Urea using zero broadcast method. The grain yield was determined hand-harvesting and shelling. RESULTS AND CONCLUSIONS: There were no statistically significant differences between the mean samples from the two replicates (blocks 1 & 2) across the two seasons for corn sugar concentration, corn yield estimates and grain yields. In 2021, the mean yield estimate was 12,552 Kg ha-1, while that of 2022 averaged 12687 Kg ha-1. Similarly, the grain yield achieved in 2022 was 844.1kg more than the average grain yield in 2021. The white corn yield estimate and grain yield increased linearly with an increase in nitrogen application level, with the highest yields achieved when nitrogen fertilizer was applied at 150kg N/ha. This demonstrates that nitrogen has a positive influence on the yield quantity of white corn. SIGNIFICANCE: The White maize model may be used to improve the formulation of decisions and enhance the precision of estimates for yield and N fate within the soil-plant-atmosphere continuum. Further, the findings of this study can significantly enhance agricultural productivity while keeping an eye on the environment.

In this exploratory work, we have examined the impact of an external static electric field on the H2 storage capacity of clathrate hydrates. To this end, we have chosen the 512 clathrate hydrate and examined the encapsulation of 1 - 4 H2 molecules within it. Results suggest that with the help of moderate electric fields (±0.10 to ±0.31V/Å), the encapsulation of 1 H2 molecule within the 512 clathrate hydrate becomes thermodynamically more favorable. In the cases of 4H2@512 and 2H2@512, however, the concerned processes become thermodynamically more favorable only when the field is applied along a specific direction. No favorable outcome could be observed in the case of 3H2@512, irrespective of the direction of the applied field. It appears from the results obtained herein that it might be possible to design a suitable external electric field to facilitate the hydrogen storage capacity of clathrate hydrates at ambient conditions, at least in certain cases.

We show that the implementation of the 1/c² transverse current-current interaction between electrons into the standard self-consistent electron BCS model in bulk under thermal equilibrium ensures in the stable superconductive phase the full compensation of a constant external magnetic field by the internal magnetic field created by the electrons i.e. one has an ideal diamagnet. However, no proof of the phenomenological London equation emerges within the bulk approach.

Meat serves as a vital component of the human diet, offering a rich source of protein and essential trace elements. China stands as both a significant producer and consumer of meat on a global scale, leading the world in terms of total meat production and consumption. As the standard of living within the country continues to rise, there is a growing emphasis on the nutritional value and safety of meat consumption. The tenderness of meat is a critical factor influencing its overall quality. Traditionally, tenderness has been assessed through shear force testing, a method that is inherently destructive, inefficient, and results in considerable sample wastage. In light of these drawbacks, non-destructive testing techniques have emerged as a preferred alternative, promising greater accuracy, efficiency, and convenience without compromising the integrity of the samples. This paper delves into the application of five advanced non-destructive testing technologies in the realm of meat tenderness assessment. These include near-infrared spectroscopy, hyperspectral imaging, Raman spectroscopy, airflow optical fusion detection, and nuclear magnetic resonance detection. Each technology is scrutinized for its respective strengths and limitations, providing a comprehensive overview of their current utility and potential for future development. Moreover, the integration of these techniques with the latest advancements in artificial intelligence (AI) technology is explored. The fusion of AI with non-destructive testing offers a promising avenue for the development of more sophisticated, rapid, and intelligent systems for meat tenderness evaluation. This integration is anticipated to significantly enhance the efficiency and accuracy of quality assessment in the meat industry, ensuring a higher standard of safety and nutritional value for consumers. The paper concludes with a set of technical recommendations aimed at guiding the future direction of non-destructive, AI-enhanced meat tenderness detection, thereby contributing to the ongoing improvement of the meat industry in China and beyond.

The research on the impact of excavation of underpass tunnels has already had certain results, but there is a lack of research cases of double-line highway tunnels with oblique angles underpass the existing railway tunnels, especially the method of determining the area of the impact of the dynamic and static loads of the new tunnels and existing trains to be enriched by considering them at the same time. In this paper, based on the tunnel project of the new double-line Shiqian Highway Tunnel with oblique angles underpass the Hurong Railway in Wanshoushan. By constructing a three-dimensional finite element model and simulating the application of static tunnel excavation load, dynamic blasting load and dynamic train operation load of the existing tunnel, the overall displacement of the existing tunnel and the settlement value of the bottom plate of the track surface by the static tunnel excavation load were analyzed. Then, the stresses, vibration speeds and displacements of the tunnel due to the dynamic blasting loads and the dynamic train operation loads were obtained. The results show that: the area of influence of the static loads of the new tunnel excavation on the existing tunnel is divided into three types of perturbations presenting strong, weak and slight; the area affected by the blasting dynamic load of new tunnel excavation is a circular domain with the datum point in the tunnel section as the center; the area affected by the dynamic load of train operation in the existing tunnel is an ellipse with the center of the track surface of the existing tunnel as the datum; there is an anomalous shape in the area affected by the blasting dynamic load of new tunnel excavation and the area affected by the dynamic load of train operation in the existing tunnel.

We report on a new form of nanoscale carbon nitride in the shape of single layer half dome structures grown on the step edges of boron nitride sheets. The half dome structure grown on the step edges of boron nitride sheets. The half dome structures are formed spontaneously at high temperature using Iron oxide nanoparticles capped with tetremethylammonium hydroxide supported on BN sheets. During the combustion process the support, firstly, acted as a reducing agent, secondly, as a source of nitrogen that permitted the transformation of the organic capping agent in sp1 CN chains linked with sp2 CN domains. During the Ostwald ripening process smaller nanoparticles migrates towards bigger nanoparticles, when the nanoparticles come across the step edges of few layer boron nitride sheets the half dome structure is formed. This new method of synthesis has demonstrated for the first time the formation of half dome structures containing cyanopolyynes sp1 chains and sp2 carbon nitride domains.

Conventional fertilization practices can lead to many ecological problems, such as nutrient imbalance, soil acidity, and reduced soil fertility in natural rubber plantations. To address these challenges, a field investigation was strategically carried out to substitute inorganic fertilizer with organic fertilizers consisted of six treatments, i.e., no fertilization (CK), inorganic fertilizer (NPK), 25 % replacement of inorganic through organic (25%M), 50 % replacement of inorganic through organic (50%M), 75 % replacement of inorganic through organic (75%M), and 100% organic fertilizer (100%M). The soil physicochemical properties (SOC, TN, AN, C:N, pH, NH4+-N, and NO3--N) and carbon and nitrogen converting enzymes (BG, NAG, and LAP) were all determined. The partial substitution of inorganic fertilizers with organic fertilizers (i.e., 75%M at surface soil layer) showed higher SOC (14.52 g.kg-1), TN (1.06 g.kg-1), AN (20.07 mg.kg-1), C:N (14.63), NH4+-N (10.63 mgkg-1), and NO3--N(11.06 mg.kg-1) than NPK and CK. Such increase in physicochemical properties in partial replacement of inorganic with organic fertilizers plots resulted from higher carbon and nitrogen enzymes activities (BG (143.17 nmol.g-1.h-1), NAG (153.96 nmol.g-1.h-1), and LAP (153.48 nmol.g-1.h-1)) compared to NPK and CK, and further the person correlation and RDA analysis confirmed a significant positive correlation between SOC, AN, and soil enzymes. This study presents a new strategy for assessing the impact of partially replacing inorganic fertilizers with organic fertilizers in rubber plantations, mainly by modifying the soil nutrient composition in tropical regions.

Molecular transport and quantum tunneling of H2 and H2O molecules through nanoporous gra-phene is studied using computational modeling and first principles density functional theory. It is demonstrated that molecules with sufficiently high kinetic energies can tunnel through the na-nopores. It is also demonstrated that molecules can be trapped in front of the nanopore or behind it. These investigations help us learn the behavior of molecules in and around nanopores of gra-phene. They also help us learn fundamentals of molecular tunneling. We believe, nanoporous gra-phene can play important roles for gas separation and nanofiltration.

new subsonic blower wind tunnel design has been studied both numerically and experimentally, it is also referred to as “blower” wind tunnel. This paper, is initially aimed to address each sequential stage of the wind tunnel design process. Rather than applying the standard method of modelling solely the flow in the test section, a large-scale CFD model of the whole wind tunnel was employed. The loss of every constituent element was calculated and then all the losses are added up to determine the power needed for the wind tunnel operation which is used as “intake fan” boundary conditions in the CFD model. Then, flow uniformity and turbulent intensity measurements in an empty test section using a Pitot-static tube and hot wire anemometer (HWA) were introduced to validate the CFD results. The results showed that flow quality was significantly affected by boundary layer controllers (honeycomb and mesh screens) in the settling chamber and wide-angle diffuser. Investigations were also conducted to evaluate the flow deficit in the wake area behind a convex hump model using HWA. This was additional experimental tests carried out to validate the suitability of the wind tunnel flow aerodynamic research.

We describe electron temperature measurements in the SSX MHD wind tunnel using two different methods. First, we estimate T_e along a chord by measuring the ratio of the C__III 97.7 nm to C_IV 155 nm line intensities using a vacuum ultraviolet monochrometer. Second, we record a biasing scan to a double Langmuir probe to obtain a local measurement of T_e. The aim of these studies is to increase the Taylor state lifetime, primarily by increasing the electron temperature. Also, a model is proposed to predict magnetic lifetime of relaxed states and is found of predict the lifetime satisfactorily. Furthermore, we find that proton cooling can be explained by equilibration with the electrons.

L-Theanine, a unique non-protein amino acid, is an important bioactive component of green tea. Previous studies have shown that L-theanine has many potent health benefits, such as anti-anxiety effect, regulation of immune response, relaxing neural tension, reducing oxidative damage. However, little is known concerning whether L-theanine can improve the clearance of mitochondrial DNA (mtDNA) damage in organisms. Here, we reported that L-theanine treatment increased ATP production and improved mitochondrial morphology to extend the lifespan of UVC-exposed nematodes. Mechanistic investigations showed that L-theanine treatment enhanced the removal of mtDNA damage and extended lifespan by activating autophagy, mitophagy, mitochondrial dynamics, and mitochondrial unfolded protein response (UPRmt) in UVC-exposed nematodes. In addition, L-theanine treatment also up-regulated the expression of genes related to mitochondrial energy metabolism in UVC-exposed nematodes. Our study provided a theoretical basis for the possibility that tea drinking may prevent mitochondrial related diseases.

The present study provides an observation and documentation on the effect of static magnetic field on the growth of Triticum aestivum. The seeds are allowed to germinate and the seedlings are grown in an environment of the controlled static magnetic field while other physical factors such as temperature, light exposure, soil pH, etc. are held constant. Also, a comparison of influence on the average height between both the poles of the magnet is estimated and north pole oriented magnet is found to imply a significant difference. Finally some of the potential applications of the study in non-invasive protein silencing, GMO production, Vertical farming and Terraforming are briefly discussed.

We study the light rays in a static and spherically symmetric gravitational field of null aether theory (NAT). To this end, we employ the Gauss-Bonnet theorem to compute the deflection angle by a NAT black hole in the weak limit approximation. Using the optical metrics of the NAT black hole, we first obtain the Gaussian curvature and then calculate the leading terms of the deflection angle. Our calculations show how gravitational lensing is affected by the NAT field. We also show once again that the bending of light stems from a global and topological effect.

This paper aims in studying the effect of vermicompost on soil and growth of the plant Sesamum indicum L. by measuring the its various growth and yield components. For this purpose, a mixture of textile mill sludge, cow dung and saw dust have been mixed in different ratios to produce vermicompost by using the earthworm Perionyx excavates and was compared with inorganic (NPK) and organic fertilizer (FYM). The results of soil quality revealed that the porosity, water holding capacity (WHC), cation exchange capacity (CEC) and occurrence of macronutrients were significantly increased and the particle density were decreased in treatment with 100% vermicompost (VC) followed by soil treated with 50% VC + 50% NPK, on contrary, reduction in porosity, WHC, CEC were noted in NPK treated plots. The effect of vermicompost on plant growth components (root, shoot, leaf area index, branch, DMP) and yield components (pod number, weight, length, seed weight, number of seed, seed yield) were significantly higher in the plots treated with 50% VC + 50% NPK followed by 100% vermicompost than the plots treated only with FYM and NPK. The significant growth upon using vermicompost was accounted by its nutrients composition over other fertilizers.

Deformation of the surface of diamagnetic liquid by magnetic field is called the “Moses Effect”. Physics and applications of the direct and inverse Moses effects are reviewed. Experimental techniques enabling visualization of the effects are surveyed. Impact of magnetic field on micro- and macroscopic properties of liquids is addressed. Influence of the surface tension on the shape of the near-surface dip formed in a diamagnetic liquid by magnetic field is reported. Floating of diamagnetic bodies driven by the Moses effect is treated. The effect of the “magnetic memory of water” in its relation to the Moses Effect is discussed. The dynamics of self-healing of near-surface dips due to the Moses Effect is considered.

Biochar application to soil has been proposed as a means for reducing soil greenhouse gas emissions and mitigating climate change. The effects, however, of interactions between biochar, moisture and temperature on soil CO₂ and N₂O emissions, remain poorly understood. Furthermore, the applicability of lab-scale observations to field conditions in diverse agroecosystems remains uncertain. Here we investigate the impact of a mixed wood gasification biochar on CO₂ and N₂O emissions from loess-derived soils using: (1) controlled laboratory incubations at three moisture (27, 31 and 35%) and three temperature (10, 20 and 30°C) levels, and (2) a field study with four cropping systems (continuous corn, switchgrass, low diversity grass mix, and high diversity grass-forb mix). Biochar reduced N₂O emissions under specific temperatures and moistures in the laboratory and in the continuous corn cropping system in the field. However, the effect of biochar on N₂O emissions was only significant in the field, and no effect on cumulative CO₂ emissions was observed. Cropping system also had a significant effect in the field study, with soils in grass and grass-forb cropping systems emitting more CO₂ and less N₂O than corn cropping systems. Observed biochar effects were consistent with previous studies showing that biochar amendments can reduce soil N₂O emissions under specific, but not all, conditions. The disparity in N₂O emission responses at the lab and field scales suggests that laboratory incubation experiments are not reliable for predicting the impact of biochar at the field scale.

The state detection of power cable is very important to ensure the reliability of power supply. Traditional sensors are mostly based on electric field detection, the operation is complex, and its efficiency needs to be improved. This paper optimizes the design and development of the magnetic field detection sensor for AC power cables. Firstly, through the establishment of the magnetic field sensor model, it is determined that permalloy is the material of the magnetic core, the optimal aspect ratio of the magnetic core is 20, and the ratio of coil length to core length is 0.3. Secondly, the coil simulation model is established, and it is determined that the optimal number of turns of the coil is 11000 turns, the diameter of the enamelled copper wire is 0.08mm, and the equivalent magnetic field noise of the sensor is 0.06pT. Finally, the amplifying circuit based on negative magnetic flux feedback is designed and the sensor is assembled, and the experimental circuit is built for sensitivity test. the results show that the sensitivity of the magnetic field sensor is 327.6mV/μT. The sensor designed in this paper has the advantages of small size, high sensitivity, easy to carry and high reliability.

Kamchatka berries (Lonicera caerulea L.) are known for their high content of phenolic compounds or vitamins, which is reflected in their antibacterial, detoxifying and anti-inflammatory properties. They are used in the production of jams, juices, wines and as natural dye. A bioferment was prepared from the pomace of the Kamchatka berry varieties Aurora and Indigo Gem and the strains Saccharomyces cerevisiae and Lacticaseibacillus paracasei, which was used to prepare a cosmetic preparation with a concentration of 5% in accordance with the guidelines of the COSMOS certification body. Conducted physico-chemical and organoleptic analyses and bioactive profile characterisation (UHPLC-DAD and UHPLC-ESI-MS/MS). The results showed that the presence of caffeic acid 4.47 ± 0.07 mg/100g was detected after fermentation of Kamchatka berry pomace. Vitamin C content increased by 141% after fermentation of Kamchatka berry pomace. The results of stability tests showed that in the process of physicochemical analysis of cosmetic preparation with bioferment of Kamchatka berry pomace the pH should oscillate in the range of 4.38-4.76 ± 0.01. Stability tests showed that the cosmetic should be protected from high temperatures and UV radiation and proved that the product is stable under changing conditions, resulting in lower transport and storage costs.

Although Darwin‘s evolutionary mutation theory has been widely accepted, many endeavors have been tried to challenge it. With more and more observation of successful hybridization and hybrids, the sexual isolation between species has become vague. The mechanism of evolution has been expanded from the classical model of evolution to multiple routes of speciation. Furthermore, a fundamental crossbreeding theory has been raised and proved by two lines of evidences: paleopolyploidy and fan-shaped spectrum of species. Ancient genome duplications are widespread throughout eukaryotic lineages, particularly in plants. The genome polyploidization, especially in the somatic cell hybridization, can break through the sexual incompatibility between diploid counterparts to hybridize and produce new species. By comparing characteristics, all species in every taxon, both in the extinct fossil and extant organisms, can be arranged into fan-shaped spectrum according to their similarity: left primitive type-middle advanced type-right primitive type. The species are primitive at the two ends and advanced at the middle. The primitive two species always resemble two types of more primitive species that can be confirmed as their ancestors respectively, and the middle species is half similar to the two ancestors respectively. These suggest that the species in the spectrum come from two different ancestors by crossbreeding and gene combination. As a sum, advanced species originated from crossbreeding of two primitive ancestors, by major method of polyploidization, and proved by results of fan-shaped spectrum of species. Then, sex is the cause, force and opportunity for evolution.

Many protein expression systems are primary utilised to produce a single, specific recombinant protein. In contrast, most biological processes such as virus assembly rely upon a complex of several interacting proteins rather than the activity of a sole protein. The high complexity of the baculovirus genome, coupled with a multiphase replication cycle incorporating distinct transcriptional steps, made it the ideal system to manipulate for high-level expression of a single or co-expression of multiple foreign proteins within a single cell. We have developed and utilised a series of recombinant baculovirus systems to unravel the sequential assembly process of a complex non-enveloped model virus, Bluetongue virus (BTV). The high protein yields expressed by the baculovirus system not only facilitated structure-function analysis of each viral proteins but were also advantageous to crystallography studies and supported the first atomic level resolution of a recombinant viral protein, the major BTV capsid protein. Further, the formation of recombinant double-shelled virus-like particles (VLPs) provided insights into the structure-function relationships among the four major structural proteins of the BTV whilst also representing a potential candidate for a viral vaccine. The baculovirus multi-gene expression system facilitated the study of structurally complex viruses (both non-enveloped and enveloped viruses) and heralded in a new generation of viral vaccines.

In this paper, we propose a methodology for analyzing the near-field coupling between two surface mount device (SMD) inductors using a 3-dimensional electromagnetic (3D-EM) model. To develop the 3D-EM model, we first extract the effective permeability of core magnetic material in the SMD using the loss tangent in the equivalent circuit model. Then the effective permeability is used in the magnetic material for the 3D-EM modeling of SMD inductor. The validity of the proposed 3D-EM model is confirmed by comparing the impedance and S-parameters obtained from both measured and EM-simulated values for the two near-field coupled SMDs. Finally, the near-field coupling effects between the two adjacent SMD inductors are visualized in terms of magnetic coupling path visualization (CPV) using the proposed 3D-EM model, which demonstrates its usefulness for near-field coupling analysis.

Berberis vulgaris (L.) has remarkable ethnopharmacological properties and is widely used in traditional medicine. The present study investigates B. vulgaris stem bark (Berberidis cortex) by extraction with 50% ethanol. The main secondary metabolites were quantified, resulting in a polyphenols content of 17.6780 ± 3.9320 mg Eq Tannic acid / 100 g extract, phenolic acids amount of 3.3886 ± 0.3481 mg Eq Chlorogenic acid / 100 g extract and 78.95 µg/g berberine. The dried hydro-ethanolic extract (BVE) was thoroughly analyzed using Ultra-High Performance Liquid Chromatography coupled with High-Resolution Mass Spectrometry (UHPLC–HRMS/MS) and HPLC and 40 bioactive phenolic constituents were identified. Then, the antioxidant potential of BVE was evaluated using three methods; our results could explain the protective effects of Berberidis cortex EC50FRAP = 0.1398 mg/mL, IC50ABTS = 0.0442 mg/mL, IC50DPPH = 0.2610 mg/mL compared to ascorbic acid (IC50 = 0.0165 mg/mL). Next, the acute toxicity and teratogenicity of BVE and Berberine - Berberine sulfate hydrate (BS) - investigated on Daphnia sp reported significant BS toxicity after 24 h; BVE revealed considerable toxicity after 48 hours and induced embryonic developmental delays. Finally, the anticancer effects of BVE and BS were evaluated on different tumor cell lines after 24 and 48 hours of treatments. The MTS assay evidenced a dose- and time-dependent antiproliferative activity, higher on BS than BVE. The strongest diminution of tumor cell viability was recorded on breast (MDA-MB-231), colon (LoVo) cancer, and OSCC (PE/CA-PJ49) cell lines after 48 h of exposure (IC50 &lt; 100 µg/mL). However, no cytotoxicity was reported on normal epithelial cells (HUVEC) and hepatocellular carcinoma (HT-29) cell lines. Extensive data analysis supports our results, showing a significant correlation between the BVE's concentration, phenolic compounds content, antioxidant activity, exposure time, and the viability rate of various normal cells and cancer cell lines.

Minirhizotron tubes were installed to monitor root growth dynamics of mature Shiraz grapevines in a rootstock trial established in the hot climate Riverina region of New South Wales, Australia. The vertical root distribution and seasonal root growth dynamics of Shiraz on own-roots and Shiraz grafted on the rootstocks Ramsey, 140 Ruggeri and Schwarzmann was studied for five seasons across a seven-year period to a depth of 60 cm. New root production was significantly influenced by genotype, soil depth, season, growth stage and year. Soil moisture and soil tem-perature were monitored at 10, 30 and 60 cm in the last two seasons. Soil moisture at 30 cm and soil temperature at all three depths were significant predictors of root growth. New root numbers were significantly higher in 140 Ruggeri than the other rootstocks. To the depth studied, 140 Ruggeri roots were evenly distributed from the topsoil down, whereas the majority of roots of Schwarzmann and Shiraz were located at intermediate depths in the 10-40 cm ad 20-40 cm zones respectively, while Ramsey roots were found at 20 cm or below. Depending on genotype, root growth occurred across several phenological stages but tended to peak at flowering. In some years we observed root growth in early and late winter at rates exceeding that of autumn, and this was associated with warmer temperatures during this period. Overall, seasonal rooting dynamics were responsive to abiotic factors but dominated by genotype.

The intracellular calcium dynamics in vascular endothelial cells (VECs) in response to wall shear stress (WSS) and/or adenosine triphosphate (ATP) have been commonly regarded as an important factor in regulating VEC function and behavior including proliferation, migration and apoptosis. However, the effects of time-varying ATP signals have been usually neglected in the past investigations in the field of VEC mechanobiology. In order to investigate the combined effects of WSS and dynamic ATP signals on the intracellular calcium dynamic in VECs, a Y-shaped microfluidic device, which can provide the cultured cells on the bottom of its mixing micro-channel with stimuli of WSS signal alone and different combinations of WSS and ATP signals in one single micro-channel, is proposed. Both numerical simulation and experimental studies verify the feasibility of its application. Cellular experimental results also suggest that a combination of WSS and ATP signals rather than a WSS signal alone might play a more significant role in VEC Ca²⁺ signal transduction induced by blood flow.

The carbonyl iron particles were dispersed in a polychloroprene rubber (CR) matrix under an external magnetic field for practical application as microwave absorption composites film. The film prepared under external magnetic field with a thickness of only 0.54 mm showed least reflection loss of -15.98 dB and the reflection loss value less than -10.0 dB over the frequency range of 11.4~14.8 GHz. In comparison with the microwave absorption properties of calculation by transmission line theory based on the tested relative complex permittivity and permeability and film prepared by general route without external magnetic field, the film made with external magnetic field exhibited more excellent microwave absorption properties, strongly depending on the increment of anisotropy and rearrangement of magnetic particles. The results indicated the composite film made under external magnetic field have excellent microwave absorption properties, which suggest that the composites thin film could be used as a thinner and lighter microwave absorber.

Developing particles of different anisotropic shapes are the hot topic since decades as they guarantee some special features of properties not possible through other means. Again, controlling atoms to develop certain size and shape particle is a quite challenging job. In this study, gold particles of different shapes are developed via pulse-based electronphoton-solution interface process. Gold atoms of certain transition state develop monolayer assembly at solution surface around the light glow (known in argon plasma) being generated at bottom of copper capillary (known in cathode). The rate of uplifting gold atoms to solution surface is being controlled by forcing energy (travelling photons) pursuing electrons and high energy photons (in high density) entering to solution. Gold atoms dissociated from the precursor under dissipating heat energy into the solution supplied under propagating photons characteristic current through immersed graphite rod (known in anode). Placing packets of nano shape energy of tuned pulse protocol over compact monolayer assembly comprising transition state atoms develop tiny-sized particles of formed shape. On separation of joint tiny particles into two equilateral triangular-shaped tiny particles, exerting forces of surface format elongate atoms of one-dimensional arrays converting them into structures of smooth elements. Due to immersing level of force, such tiny-shaped particles pack from different zones at centre of light glow where they assembled structures of smooth elements for developing mono-layers of different shapes of particles. Developing one-dimensional particles deal assembling of structures of smooth elements of packing tiny-shaped particles from nearly rearward zones of reflection of north-south poles, whereas, developing multi-dimensional particles deal assembling of structures of smooth elements of packing tiny-shaped particles from the east-west poles and near regions. Depending on the number of assembled structures of smooth elements at point of nucleation, packing of tiny-shaped particles from different zones develop different shapes of the anisotropic particles. At fixed precursor concentration, increasing the process time results into develop particles of low aspect ratio. Under tuned parameters, developing mechanisms of particles exhibiting unprecedented features are discussed.

Background: Alfalfa, the most economically important forage legume worldwide, features modest genetic progress due to long selection cycles and large extent of non-additive genetic variance associated with its autotetraploid genome. Methods: To improve the efficiency of genomic selection in alfalfa, we explored the effects of genome parametrization (as autotetraploid and diploid dosage, plus allele ratios) and SNP marker subsetting (all available SNPs; only genic regions; only non-genic regions) on genomic regressions, together with various levels of filtering on reading depth and missing rates. We used Genotyping by Sequencing-generated data and focused on traits of different genetic complexity, i.e., dry biomass yield in moisture-favorable (FE) and drought stress (SE) environments, leaf size, and onset of flowering, assessed on 143 genotyped plants from a genetically-broad European reference population and their phenotyped half-sib progenies. Results: On average, allele ratio improved the predictive ability compared with other genome parametrizations (+7.9% vs. tetraploid dosage, +12.6% vs. diploid dosage), SNP subsetting offered an advantage compared with any tested subsettings (+3.7% vs. genic regions, +7.6% vs. non-genic regions). However, when focusing on specific traits, different combinations of genome parametrization and subsetting reached better performances. We also released Legpipe2, a SNP calling pipeline tailored for reduced representation (GBS, RAD) medium-sized genotyping experiments.

The effect of configuration of an asymmetric bulky initiator 2,2’-[1,1’-binaphtyl-2,2’-diyl- bis-(nitrylomethilidyne)]diphenoxy aluminum isopropoxide (Ini) on structure of copolymer of asymmetric monomer L,L-lactide (Lac) with symmetric comonomer trimethylene carbonate (Tmc) was studied using polarimetry, dilatometry, SEC and ¹³C NMR. When the S-enantiomer of Ini was used the distribution in copolymer chains at the beginning of polymerization is statistical, with alternacy tendency, changing next through a gradient region to homoblocks of Tmc. When, however, R-Ini was used, the product formed was a gradient oligoblock one, with Tmc blocks prevailing at the beginning, changing to Lac blocks dominating at end part of chains. Initiation of copolymerization with the mixture of both initiator enantiomers (S:R = 6:94) gave multiblock copolymer, of similar features but shorter blocks. Analysis of copolymerization progress required complex analysis of dilatometric data, assuming different molar volume contraction coefficients for units located in different triads. Comonomer reactivity ratios of studied copolymerizations were determined.

In this work, we investigate the weak deflection angle of light from exact black hole within the non-linear electrodynamics. First we calculate the Gaussian optical curvature using the optical spacetime geometry. With the help of modern geometrical way popularized by Gibbons and Werner, we examine the deflection angle of light from exact black hole. For this desire, we determine the optical Gaussian curvature and execute the Gauss-Bonnet theorem on optical metric and calculate the leading terms of deflection angle in the weak limit approximation. Furthermore, we likewise study the plasma medium's effect on weak gravitational lensing by exact black hole. Hence we expose the effect of the non-linear electrodynamics on the deflection angle in the weak gravitational field.

We study the effect of polymer coating, pressure, temperature and light on the electrical characteristics of monolayer WSe₂ back-gated transistors with quasi-ohmic Ni/Au contacts. We prove that the removal of a layer of poly(methyl methacrylate) or a decrease of the pressure change the device conductivity from p to n-type. We demonstrate a gate-tunable Schottky barrier at the contacts and measure a barrier height of ~70 meV in flat-band condition. We report and discuss a temperature-driven change in the mobility and the subthreshold slope which we use to estimate the trap density at the WSe₂/SiO₂ interface. We study the spectral photoresponse of the device, that can be used as a photodetector with a responsivity of ~0.5 AW^-1 at 700 nm wavelength and 0.37 mW/cm² optical power.

This study investigated the effects of two plyometric training protocols on sprint and change of direction (COD) performance in elite hockey players. A parallel-group randomized controlled trial design was used and seventeen elite male and female field hockey players were randomly allocated into either low-to-high (L-H, n = 8) or high-to-low (H-L, n = 9) training groups. Each group performed separate variations of the drop jump exercise twice weekly for six weeks, with an emphasis on either jump height (L-H) or drop height (H-L). Performance variables assessed included sprint times over 10 m and 20 m, as well as 505 time. A two-way repeated measures analysis of variance was performed and Cohen’s d effect sizes were calculated. The H-L group displayed significant small ES improvement from baseline to post-training in the 10 m sprint (1.893 ± 0.08 s pre vs 1.851 ± 0.06 s post) (ES = −0.44) (P = <0.05). Small but not statistically significant differences between groups were observed for 10 m and 20 m sprint performance, and no significant differences were observed within or between groups for 505 time. These findings highlight the difficulty in substantially enhancing speed and COD ability in highly trained athletic populations through the addition of a low volume, short duration plyometric training protocol.

In this paper, an analytical investigation of the combined effect of through flow and magnetic field on the convective instability in an electrically conducting fluid layer, bounded in a Hele-Shaw cell is presented within the context of linear stability theory. The Galarkin method is utilized to solve the eigenvalue problem. The outcome of the important parameters on the stability of the system is examined analytically as well as graphically. It is observed that the through flow and magnetic field have both stabilizing effects, while the Hele-Shaw number has destabilizing effect on the stability of system. It is also found that the oscillatory mode of convection possible only when the magnetic Prandtl number takes the values less than unity.

This paper introduces a method for tunnel point cloud and BIM model integration and cross-section monitoring, providing information to analyse tunnel cross-sections and surrounding rock deformation, and support for tunnel maintenance and reconstruction. Three types of data are processed for the integration: laser scanning point cloud, BIM tunnel model and terrain model from oblique photogrammetry. An adaptive BIM modelling scheme is proposed for tunnels with alien structures. Precise spatial registration of the data sets is conducted by applying singular value decomposition (SVD) algorithm to calculate transformation parameters from the point cloud model to the BIM model. Since the tunnel central line has high-order derivability, a cross-section calculation method based on tangent vector is proposed to obtain the cross-sectional profile of tunnels at any mileage. The proposed method has been verified by applying it to a tunnel reconstruction project. The experiment results show that the tunnel point cloud and the BIM model were highly coincident after the integration. The developed program can effectively get the cross-section of the tunnel at any mileage, and correctly express the spatial relationship between the BIM tunnel, the point cloud of tunnel and the external mountainous terrain.

Due to poor ventilation conditions in the tunnel, if gas pipeline leaks, the consequence of the accident will be more serious. Therefore, before the emergency repair, gas in the tunnel needs to be excharged so as not to explode during the repair process. Therefore, it is necessary to study the ventilation of gas in the tunnel. Based on the computational fluid dynamics (CFD) theory and taking the Yanyingshan tunnel section of China-Myanmar pipeline as an example, this paper uses Fluent software to establish the leakage model of the gas pipeline and fan model in the tunnel and analyzes the influence of different fan locations and number of fans on gas concentration. It can be concluded that: (1) the use of press-in method makes it more efficient to discharge gas out of the tunnel. (2) In order to make ventilation efficient, the fan should be arranged in a higher position and needs to be at a distance from the top of the tunnel. (3) Parallel use of two fans has better ventilation effect than single fan.

The assortment of low-cost 3D printers for “in-practice” use, e.g., for clear aligner therapies, is ever increasing. To address concerns about the accuracy of orthodontic models produced on such printers when cost efficient modes of 3D printing are employed, this study examined the effect of print model body type and print angulation on accuracy. Six printing-configuration groups were included: 2 model types (solid or hollow shell) combined with 3 print angles (0°, 70°, or 90°) with 10 models/group; all models were printed with 100-µm layer thickness using a digital light processing-based 3-dimensional printer. Eleven selected structures and distances were measured on the printed models with a digital microscope and compared to the same measures on a digitized master model. The clinically-acceptability range was set at ±0.25 mm difference from the master model for single tooth measurements (intra-tooth) and ±0.5 mm for cross-arch measurements (inter-tooth). For individual measurements across all models, 98% fell within clinical acceptability. For mean measurements within each model group, only canine height for the shell-0° model had a mean difference (0.26 mm ± 0.03) outside the clinically acceptable range for intra-tooth measurements. Standard deviations for all intra-tooth measurements were within 0.07 mm. While none of the mean inter-tooth measurements exceeded the acceptability range, the standard deviations were larger (0.04 to 0.30 mm). Accuracy of orthodontic models for clear aligner therapies was not impacted beyond the clinically acceptable range when altering model body type and print angulation to improve efficiency of 3D printing. These findings suggest greater flexibility of the practitioner to alter print settings to address time and cost efficiency in various clinical scenarios and still maintain clinically acceptable model accuracy.

According to statistics from the Food and Agriculture Organization, the world population will increase to about 91 million (Asia 51 million, Africa 19 million). A rise in the world’s population means an increased need for food. However, climate change has caused desertification and unpredictable weather, creating problems in the supply and demand of food. Sweet potato (Ipomoea batatas) is an alternative to solving the food problem, as it is one of the world’s most important food crops, especially in developing countries. The tuberous roots of sweet potato are usually used as staple food, animal feed, industrial material, or raw material for alcohol production. In the future, more variations of sweet potato will be needed for breeding this crop. Recently, molecular markers developed for sweet potato have demonstrated good potential for use in genetic selection. In this study, a cDNA library was constructed from the total RNA of sweet potato leaves. A total of 789 copies of the cDNA were cloned in Escherichia coli by employing the pGEM-T Easy vector. Sequencing was carried out by Solgent Co. (Korea). As many as 579 expressed sequence tag–simple sequence repeat (EST-SSR) markers were designed (73.38%) from the known cDNA nucleotide base sequences. The lengths of the developed EST-SSR markers ranged from 100 to 499 bp (average length 238 bp). Their motif sequence types were varied, with most being dinucleotides and pentanucleotides, and the most commonly found motifs were CAGAAT (29.0%) and TCT (2.8%). Based on these SSR-containing sequences, 619 pairs of high-quality SSR primers were designed using WebSat and Primer3web. The total number of primers designed was 144. Polymorphism was evident in 82 EST-SSR markers among 20 Korean sweet potato cultivars tested and in 90 EST-SSR markers in the two parents of a mapping population, Yeseumi and Annobeny. In this study, the hexaploid sweet potato (2n = 6x = 90) EST-SSR markers were developed in the absence of full-sequence data. Moreover, by acting as a molecular tag for particular traits, the EST-SSR marker can also simultaneously identify information about the corresponding gene. These EST-SSR markers will allow the molecular analysis of sweet potato to be done more efficiently. Thus, we can develop high-quality sweet potato while overcoming the challenges from climate change and other unfavorable conditions.

Soil salinity is seen as a major restriction for crop production, and with water scarcity this problem becomes more complicated. Mulching is crucial to salinity dynamics management by decreasing evaporation with improving the soil’s characteristics. Using chitosan as an eco-friendly biostimulant can enhance plant defense genes during different abiotic stresses. Recently, agricultural research has recognized nanoparticles as a pioneer material due to their distinctive physicochemical features. Therefore, a lysimeter experiment was conducted to investigate the interactive effects of mulching (UNM: un-mulched, WPM: white plastic, RSM: rice straw and SDM: sawdust) and chitosan foliar application (Ch0: control, Ch1: 250 mg chitosan L-1, Ch2: 125 mg nano chitosan L-1, and Ch3: 62.5 mg nano chitosan L-1) on the biochemical soil characteristics and common beans productivity under salt affected soil conditions. Organic mulching (RSM and SDM) treatments significantly improved the soil's organic carbon, available nutrient content, and total count of bacteria. WPM treatment lowered soil EC to 6.63 dS m-1 and increased soil water content to 34.13%. The application of Ch3 caused considerable increases in the plant height, shoot dry weight, root dry weight, grain yield, and nutrient content in the seed. The total fungi count in the soil and Na% in the seed was significantly decreased due to chitosan foliar applications. Moreover, the interactive effect of different mulch materials plus foliar by chitosan applications gave a statistically similar seed yield in both seasons. Overall, this study revealed the potential of the mulching treatments and foliar application of nano chitosan in improved biochemical soil characteristics and common bean productivity under saline soil conditions.

Nitrogen fertilization ensures the proper growth of trees. The aim of the study was to evaluate the impact of differentiated nitrogen fertilization on selected parameters. It was assumed that such analysis is an indirect picture of the needs of cherries grown in herbicide fallow. The content of minerals in two layers of the soil, in leaves, and its influence of tree growth, and the content of chlorophyll in leaves were assessed. The experiments were carried out in three different cherry orchards. Three levels of fertilization were applied in each orchard: 0 kg, 60 kg and with 120 kg N ha- 1. As expected the fertilization resulted in an increase in the content of nitrate and ammonium forms of nitrogen in the soil, however, their content was also dependent on precipitation and temperature. Additionally a high nitrogen fertilization increased the content of phosphorus and potassium and decreased the magnesium in the topsoil layer. High nitrogen fertilization caused the decrease of content of phosphorus and potassium in the leaves. The level of calcium and magnesium in leaves increased with fertilization of 60 kg N ha–1 but decreased with the dose to 120 kg N ha–1. The use of nitrogen fertilization increased the vegetative growth of trees measured by leaf area and trunk cross-sectional area. However, the chlorophyll content was not dependent on the amount of nitrogen fertilization.

Management practices must be developed to improve yam production sustainability. Image-based phenotyping techniques could help developing such practices based on non-destructive analyses of important plant traits. Our objective was to determine the potential of image-based phenotyping methods to assess traits relevant for tuber yield formation in yam grown in glasshouse and field. We took plant and leaf pictures with consumer cameras. We used the numbers of image pixels to derive the shoot biomass and the total leaf surface and calculated the ‘triangular greenness index’ (TGI) which is an indicator of the plant nitrogen (N) nutritional status. Under glasshouse conditions, the number of pixels obtained from nadir view (image taken top down) was positively correlated to the shoot biomass, and the total leaf surface, while the TGI was negatively correlated to the N content of diagnostic leaves. Under field conditions, pictures taken from the nadir view showed an increase in soil surface cover and a decrease in TGI with time. TGI was negatively correlated to SPAD measured on specific leaves but was not correlated to the N content of these leaves. In conclusion, these phenotyping techniques deliver relevant results but need to be further developed and validated for application in yam.

Many advanced technologies have been employed in the high performance active matrix displays including liquid crystal displays, organic light emitting diode displays, and micro light emitting diode displays. On the other side, there have existed the strong demand on the cost reduction and it is one of low cost schemes to integrate the driver circuit in a panel based on thin film transistor technologies. This paper reviews overall concept, operation principles, and various circuit approaches in shift registers for the scanning pulse generation. In addition, it deals with the implementation of additional functionalities in gate drivers to support pixel compensation, multi-line driving, in-cell capacitive touch screen, pixel sensing, and adaptive scanning region control.

Ever since Varela and Maturana proposed the concept of autopoiesis as the minimal requirement for life, there has been a focus on cellular systems that erect topological boundaries to separate themselves from their surrounding environment. Here we reconsider whether the existence of such a spatial boundary is strictly necessary for self-producing entities. This work presents a novel computational model of a minimal autopoietic system inspired by dendrites and molecular dynamics simulations in three-dimensional space. A series of simulation experiments where the metabolic pathways of a particular autocatalytic set are successively inhibited until autocatalytic entities that could be considered autopoietic are produced. These entities maintain their distinctness in an environment containing multiple identical instances of the entities without the existence of a topological boundary. This gives rise to the concept of a metabolic boundary which manifests as emergent self-selection criteria for the processes of self-production without any need for unique identifiers. However, the adoption of such a boundary comes at a cost, as these autopoietic entities are less suited to their simulated environment than their autocatalytic counterparts. Finally, this work showcases a generalized metabolism-centered approach to the study of autopoiesis that can be applied to both physical and abstract systems alike.

Micronutrient deficiencies are a major public health problem. Beans are an important plant-based source of iron, zinc and copper, but their absorption is reduced in the presence of anti-nutrients such as phytates, polyphenols and tannins. Soaking and discarding the soaking water before cooking is unanimously recommended, but this can result in mineral loss. Data on the consequences for mineral bioaccessibility is still limited. This study aimed to evaluate iron, zinc and copper bioaccessibility in black beans cooked (regular pan, pressure cooker) with and without the soaking water. Minerals were quantified by ICP-MS, myo-inositol phosphates (InsP₅, InsP₆) by HPLC ion-pair chromatography, total polyphenols using Folin-Denis reagent and condensed tannins using Vanillin assay. Mineral bioaccessibility was determined by in vitro digestion and dialysis. All treatments resulted in a statistically significant reduction of total polyphenols (30%) and condensed tannins (20%). Only when discarding the soaking water a loss of iron (6%) and copper (30%) was observed, and InsP₆ was slightly decreased (7%) in one treatment. Bioaccessibility of iron and zinc were low (about 0.2% iron and 35% zinc), but copper presented high bioaccessibility (about 70%). Cooking beans under pressure without discarding the soaking water resulted in the highest bioaccessibility levels among all household procedures. Discarding the soaking water before cooking did not improve the nutritional quality of the beans.

Revealing the spatial distribution mechanism of the coupling effect between soil water and salt is essential for managing saline-alkali farmland. This study utilized the multifractal method to analyze soil water and salt under varying water content levels in arid saline-alkali farmland. Soil samples were collected on the second (S1), fifth (S2), eighth (S3), eleventh (S4), and fourteenth (S5) days after a rainfall event. The findings showed that a significant decrease in soil water content, contrasting with an increase in soil salt content throughout the soil layers post-rainfall. As water content decreased, the spatial variability of soil water initially increased from S1-3 and then decreased, while the spatial variability of soil salt decreased. The spatial distribution between soil water and salt exhibited a high correlation at S3-4 (with relative water content of soil ranging from 0.52 to 0.75) due to their coupling effect. However, soil salt was unevenly leached by rainfall at high water content levels (S1-2) and precipitated at low water content levels (S5), resulting in low spatial variability correlations between soil water and salt. This study elucidated the coupling process of soil water and salt, identifying their spatiotemporal distribution mechanism in dryland agricultural areas.

A fluid flowing over an object has a tendency to drag the object along it^’s flow direction. An object passing through a fluid which is stationary there is a tendency to slow the object down. For a stationary object in a fluid which is flowing there is a tendency to move the object in the fluid flowing direction .These tendencies of flowing fluid is known as drag. While moving through air airplanes also subjected to several drags. Airplanes subjected to pressure drag or form drag due to flow separation which is based on the pressure difference between the upstream and downstream surfaces of the object. Airplanes also subjected to Skin friction drag which results from the viscous shear of the fluid flowing over the object surface. In order to overcome these drags airplane wings cross section airfoils are designed very carefully. National Advisory Committee for Aeronautics, or NACA, developed and tested "families" of airfoils. Some of the most successful of these were the NACA four-digit and five-digit series. The necessary coordinates for designing NACA airfoil profiles are available in online. UIUC also provide coordinates for designing NACA airfoil profiles. But the present work describes the way of designing NACA four digit airfoils without taking any coordinates from available sources like google or any other search engines. Using C programming with the help of NACA provided equations a generalized source code is designed .Which will provide coordinates for designing any NACA four digit airfoil profiles .With the help of this obtained profile the wing model is also constructed using solid works. Using solid works model the real model was constructed using wood. The chord of regular surface airfoil is 21 cm and the span is also 21 cm. The airfoil profile taken for the model construction is NACA-4415 which is a four digit cambered airfoil.The present work also show some figures of an airfoil by applying certain surface modifications in form of dimples.

Cultivated adlay or Job’s tear (Coix lacryma-jobi L.) is an important food crop having numerous therapeutic and nutraceutical health benefits. Our study aimed to determine nutrients, minerals, fatty acid composition, and functional groups of seven wild Adlay accessions (brown, black, yellow, grey, green, off-white, and purple) to find out their scope as cereal crops using simple, rapid, and modern analytical techniques. Results revealed variations among bulk densities, specific densities, percent empty spaces, and corresponding grain counts per 10g of sample are valuable characteristics in distinguishing the accessions. Contents of fat, protein, ash, and fibre were found to be comparable to cultivated Adlay. Brown adlay was measured with the highest protein, fat, and fibre contents, 15.82%, 4.76% and 2.37%, respectively. Phosphorus, potassium, calcium, and sodium ranged 0.3% - 2.2%, whereas boron, iron, copper, zinc, and manganese were in the range 1.6mg/kg - 20.8mg/kg. Wild adlay triglyceride composition constituted of polyunsaturated fatty acids as primary fraction followed by olein and palmitic acid as prominent fatty acids. Distinguishing functional groups expressed infra-red frequencies in narrow bands and fingerprint region of proteins associated with out-of-plane region evident structural differences among adlay accessions. Frequency of functional groups in seven accessions indicated black genotype promising for varietal development.

Object-level Simultaneous Localization and Mapping (SLAM) has gained popularity in recent years since it can provide a means for intelligent robot-to-environment interactions. However, most of these methods assume that the distribution of the errors is gaussian. This assumption is not valid under many circumstances. Further, these methods use a delayed initialization of the objects in the map. During this delayed period, the solution relies on the motion model provided by an Inertial Measurement Unit (IMU). Unfortunately, the errors tend to accumulate quickly due to the dead-reckoning nature of these motion models. Finally, the current solutions depend on a set of salient features on the object’s surface and not the object’s shape. This research proposes an accurate object-level solution to the SLAM problem with a 4.1 to 13.1 cm error in the position (0.005 to 0.021 of the total path). The developed solution is based on Rao-blackwellized Particle Filtering (RBPF) that does not assume any predefined error distribution for the parameters. Further, the solution relies on the shape and thus can be used for objects that lack texture on their surface. Finally, the developed tightly coupled IMU/camera solution is based on an undelayed initialization of the objects in the map.

This Letter revisits the instability of jet produced by shaped charge. Scaling laws for shaped charge jet are derived by dimensional analysis. It shows that the scaling laws are universal when cross-sectional shrinkage rate is not included in the formulation.

An atomic-scale approach is employed to simulate the formation of precipitates with different lattice misfits in the early stages of aging of supersaturated aluminum alloys. Simulation results reveal that the increase of lattice misfit could significantly promote the nucleation rate of precipitates, which results in a larger number and smaller size of the precipitates. The morphologies of the precipitates also vary with the degree of lattice misfit. Moreover, the higher the lattice misfit, the earlier the nucleation of the second phase occurs, which can substantially inhibit the movement of dislocations. The research on the lattice misfit of precipitation can provide theoretical guidance for the design of high-strength aluminum alloy.

UAV has become powerful devices for both practitioners and researchers. In recent years, there has been a substantial growth in the usage of UAV for a wide range of applications in research and engineering. UAV are mostly utilized for image capturing techniques due to their time savings, low cost, minimum field work, and high precision. The purpose of this study is to generate an accurate and reliable 3D modelling process using UAVs photogrammetric technology; hence this study allows the techniques to evaluate the practicability of modelling and mapping inaccessible tunnels using images recorded by UAVs and photogrammetry. As a result, the approach was always employed to depict the true state of the place. This research incorporates three experiments. The first experiment is to build a 3D model using only one-directional light source and evaluate the accuracy of 3D photogrammetric model and conducted at the concrete tunnel. The second one is to build a 3D model of underground sewer tunnel using different light sources one-directional and omni-directional. The last experiment was to build 3D model using an UAV system which is developed based on first and second experiment’s result, evaluate an accuracy of 3D photogrammetric model and conducted at the tunnel named in the research as a “pedestrian tunnel. There is certain limitation in this study such as Adding a payload to a drone changed its weight distribution, which affected its stability. If the payload was not properly balanced, it caused the drone to fly unevenly, making it more difficult to control.

The study takes into account different classes of tunnel boring machines (TBMs), with the aim of identifying correlation models which are meant to estimate, at a preliminary design phase, the construction time of a tunnel and to evaluate the mechanical and operational parameters of the TBMs, starting from the knowledge of the tunnel length and/or the excavation diameter. To achieve this goal, first of all a database was created, thanks to the collection of the most meaningful technical parameters from a large number of tunnels; afterward, it was statistically analysed through Microsoft Excel. In a first phase, forecasting models were identified for the three types of machines investigated, separately for compact rocks (open TBM) and fractured rocks (single and double shield TBM). Then, the mechanical parameters collected through the database were analysed, with the aim of obtaining models that take into account, in addition to the type of TBM, the geological aspect, and the type of rock characterising the rock mass. Finally, the validation of the study was proposed in a real case, represented by the Moncenisio base tunnel, a work included in the new Turin–Lyon connection line. The estimated values were compared with the real ones, in order to verify the accuracy of the experimental models identified.

In this paper, we propose an imagined speech-based brain wave pattern recognition using deep learning. Multiple features were extracted concurrently from eight-channel Electroencephalography (EEG) signals. To obtain classifiable EEG data with fewer number of sensors, we placed the EEG sensors on carefully selected spots on the scalp. To decrease the dimensions and complexity of the EEG dataset and to avoid overfitting during the deep learning algorithm, we utilized the wavelet scattering transformation. A low-cost 8-channel EEG headset was used with MATLAB 2023a to acquire the EEG data. The Long-Short Term Memory Recurrent Neural Network (LSTM-RNN) was used to decode the identified EEG signals into four audio commands: Up, Down, Left, and Right. Wavelet scattering transformation was applied to extract the most stable features by passing the EEG dataset through a series of filtration processes. Filtration has been implemented for each individual command in the EEG datasets. The proposed imagined speech-based brain wave pattern recognition approach achieved a 92.50% overall classification accuracy. This accuracy is promising for designing a trustworthy imagined speech-based Brain-Computer Interface (BCI) future real-time systems. For better evaluation of the classification performance, other metrics were considered, and we obtained 92.74%, 92.50% and 92.62% for precision, recall, and F1-score, respectively.

We aimed to investigate the relationship between membrane material and development of membrane fouling in a membrane bioreactor (MBR) using membranes with different pore sizes and hydrophilicities. Batch filtration tests were performed using submerged single hollow fiber membrane ultrafiltration (UF) modules with different polymeric membrane materials including cellulose acetate (CA), polyethersulfone (PES), and polyvinylidene fluoride (PVDF) with activated sludge taken from a municipal wastewater treatment plant. The three UF hollow fiber membranes were prepared by a non-solvent-induced phase separation method and had similar water permeabilities and pore sizes. The results revealed that transmembrane pressure (TMP) increased more sharply for the hydrophobic PVDF membrane than for the hydrophilic CA membrane in batch filtration tests, even when membranes with similar permeabilities and pore sizes were used. PVDF hollow fiber membranes with smaller pores had greater fouling propensity than those with larger pores. In contrast, CA hollow fiber membranes showed good mitigation of membrane fouling regardless of pore size. The results obtained in this study suggest that the surface hydrophilicity and pore size of UF membranes clearly affect the fouling properties in MBR operation when using activated sludge.

A relevant improvement of the cultivar conditions of Rosmarinus officinalis L. in desert areas was achieved by a specific combination between irrigation system and soil conditioner. A drastic reduction of water employment was obtained without affect the quality of the plants, determined by monitoring growth parameters and essential oil characteristics. In particular, the effect of surface and subsurface drip irrigation systems and different soil conditioners on growth parameters, yield, and essential oil constituents of rosemary plant was assessed. Field experiments at the Agricultural Research Station (Al-Adlya farm), SEKEM group Company, El-Sharkiya Governorate, Egypt, conducted over the two seasons revealed the effectiveness of the subsurface irrigation system in obtaining better performances, especially in terms of water saving. The combination of subsurface irrigation and the conditioner Hundz soil with bentonite showed the maximum mean values of growth characters compared with other soil amendments during both seasons. The possibility to employ a water-saving irrigation system as the subsurface one without any drawback in the resulting plants was also explored in terms of molecular composition. GC-MS analysis of the essential oil extracted from plants growth under different irrigation conditions revealed a comparable composition in both cases. The goodness of the most performing system was also confirmed by the comparable yield of the essential oil.

Lactobacilli are considered an inexhaustible source of potentially bioactive substances; indeed, several products from their metabolism are known to have immunomodulatory and anti-inflammatory activity. Recently, we demonstrated that cell-free supernatants (CFS) obtained from Lactobacillus (L.) acidophilus, L. plantarum, L. rhamnosus and L. reuteri can impair Candida pathogenic potential in an in vitro model of epithelial vaginal infection. This effect could be ascribed to a direct effect of living lactobacilli on Candida virulence and to the production of metabolites which are able to impair fungal virulence. In the present work, stemming from those data, we deepened our knowledge on the CFS from these 4 lactobacilli by performing a metabolomic analysis to better characterize their composition. By using an untargeted metabolomic approach, we detected consistent differences in the metabolites produced by these four different lactobacilli. Interestingly, L. rhamnosus showed the most peculiar metabolic profile. Specifically, after a hierarchical clustering analysis in positive and negative ionization mode, L. rhamnosus showed a specific area of significant overexpressed metabolites that strongly differed from the same area in other lactobacilli. In this area, inosine was identified among the overexpressed metabolites of L. rhamnosus. This molecule has been described to have antioxidant, anti-inflammatory, anti-infective and neuroprotective properties. The biological significance of its overproduction by L. rhamnosus might be important in its probiotic and/or postbiotic activity.

To facilitate the computation of the uniaxial compressive strength value of the cemented paste backfill under the condition of high sand-cement ratio, and to analyze the size effect of the cemented paste backfill with high sand-cement ratio under varied aspect ratios, the cemented paste backfill specimens with sand-cement ratios of 8:1-24:1 and aspect ratios of 0.5, 1, and 2 were prepared. Through response surface experiments and finite element analysis, the influence of three aspect ratios on the cemented paste backfill strength was explored, and the failure characteristics and size effect mechanisms of cemented paste backfill with various aspect ratios were analyzed. The model of strength conversion between cemented paste backfill with different aspect ratios was established. The results show that the compressive strength of the cemented paste backfill decreases with the increase of the aspect ratio under the same mass concentration and sand-cement ratio. When the aspect ratio is 0.5 and 1, the splitting failure is the main factor; when the aspect ratio is 2, the shearing failure is the main factor. The three-dimensional stress caused by the end effect of the cemented paste backfill is the main reason for the high strength when the aspect ratio is 0.5. Due to the one-dimensional stress zone generated in the middle of the cemented paste backfill with an aspect ratio of 2 in the laboratory, its strength value is closer to the actual uniaxial compressive strength value of the cemented paste backfill. The strength values of the cemented paste backfill with aspect ratios of 0.5 and 1 were higher than the actual uniaxial compressive strength values in the laboratory. The rationality of the theoretical analysis was verified by the ABAQUS analysis results. According to the experimental results, a strength conversion model between different aspect ratios is established, which can provide a reference for the design of the uniaxial compressive strength of the cemented paste backfill.

Background: People with Down syndrome (DS) have a trisomy of chromosome 21 and marked deficits in verbal memory but relatively preserved visuospatial perception. Verbal memories are related to semantic knowledge. Little is known about the organization of semantic knowledge in people with DS, which was the aim of this study. Aims: The extent of false memory in people with DS was examined. Possible differences in the number of false memories induced by nominal and verbal themes were examined. Methods and Procedures: In the study phase, ten word lists with semantically related associates were presented. In the recognition phase, participants made judgments on whether each word had been represented previously as semantically related lures, old words, and semantically unrelated new words. Outcomes and Results: Differences in the processing of nominal and verbal theme-related lures were observed among people with DS. When processing nominal theme-related lures, people with DS showed delayed false positives. When processing verbal theme-related lures, people with DS showed no differences compared to controls. Similar patterns have been observed in people with DS when processing nominal theme-related associates and verbal theme-related associates. People with DS have delayed recognition of associates. When processing unrelated words, they showed significantly higher false positives than controls for both nominal and verbal eliciting themes. Further analyses of the themes revealed differences in false positives across syntactic categories among groups. Conclusions and Implications: People with DS showed a delayed recognition of associates and deviance in recognizing unrelated words in the nominal and verbal theme categories. People with DS were delayed in terms of nouns, but deviated with verbs in associated and unrelated words. Additionally, people with DS showed distinct patterns in processing five nominal lures and three verbal lures, suggesting that they formed false memories differently based on distinct syntactic categories. Thus, it was concluded that people with DS develop a deviant semantic structure. Category-based interventions for people with DS should be implemented in order to improve their semantic knowledge through lexical connections.

Six bacterial strains with differing abilities to produce varying concentrations of Indole Acetic Acid were tested individually and in consortia for plant growth promoting and fitness related traits of Cicer arietinum. In all experiments the presence of the nitrogen fixer Mesorhizobium ciceri resulted in increased biomass production. In the absence of this strain, IAA Psedomonas putida and Bacillus megaterium hinder plant growth and fitness related traits. The application of mixes of the three strains always resulted in better plant performance when M. ciceri was present. Whereas P. putida has a noticeable plant growth-promoting effect B. megaterium resulted less effective. The low levels of IAA produced by the selected strains had a significantly greater positive effect on plant biomass accumulation, flower, pods and seed production as well as on total plant nitrogen and nitrogen concentration in seed than high IAA producer strains.

In this study, a field experiment was conducted to evaluate the growth and yield responses of Sri Lankan lowland rice (Oryza sativa L.) with the application of beneficial Arbuscular mycorrhizal fungi (AMF) inoculum, and inter-cropping with highly mycorrhizal dependent vetiver grass (Chrysopogon zizanioides L.) under two different soil nutrient management systems (NMSs): conventional/chemical (CNMS) and organic (ONMS). The experiment was designed as a split plot with three blocks. Each CNMS and ONMS experiment included untreated control (T0), and three treatments—AMF inoculation (T1), vetiver intercropping (T2), and the combination of AMF and vetiver (T3). According to the results, colonization of rice roots with AMF was not affected significantly by the treatments and ranged from 0‒15.8%. The effect was very low or absent in the early stage and then higher in the later stages of the rice plant. Furthermore, plant growth was not significantly different between the two NMSs, although grain yield was significantly higher (P &lt; 0.05), with the order T1 (0.45 kg/m2) &gt;T2 (0.42 kg/m2) &gt;T3 (0.41 kg/m2) in CNMS and T2 (0.44 kg/m2) &gt;T1 (0.41 kg/m2) &gt;T3 (0.40 kg/m2), in ONMS than for the respective controls (T0), thus suggesting beneficial utilization of AMF and vetiver in the lowland rice farming system.

Background: Patients with mild cognitive impairment end up progressing to Alzheimer’s disease (AD) leading to straining burden on public health. R. officinalis long been known as the herb of remembrance and can be a potential cognition enhancer for AD. The aims of the review were to summarize the qualitative and quantitative aspects of R.O and its active constituents in enhancing the cognition. MATERIALS AND METHOD Google scholar and PubMed structured search to find relevant studies that assessed the effect of R.O extract or any of its active constituents on cognitive performance in animals. Data extraction: Following information from each included study was extracted: (1) article information (2) characteristics of study animals (3) type of intervention; type, dose, duration, and frequency of administration of R.O (4) type of outcome measure. Data synthesis: Data were analyzed using Review Manager (RevMan 5.3, 2014] and meta-analysis was performed for the outcome measures on all relevant tasks within the included papers by computing the standardized mean difference ps. RESULTS. 23 studies for qualitative and fifteen for meta-analysis were selected. From fifteen included papers, 22 studies with 35 comparisons were meta-analyzed. Effect sizes for intact animals and impaired animals respectively was (mean g and 95% CI 1.19 [0.74, 1.64; 0.57 [0.19,0.96]. The R. officinalis had positive effect on both groups of animals. The subgroup analyses exhibited substantial unexplained heterogeneity between studies. Mechanisms of R.O was anticholinesterase, procholinergic, antioxidant, anti-amyloid, neuroprotective and anti-inflammatory agent CONCLUSIONS: R.O improves cognitive function. Limitations: Considerable heterogeneity between studies.

Background and objectives: This study were designed to determine uric acid concentration and renal histopathology of M. calabura L. stem bark extract in diabetic rats and to compare the natural product of M. calabura L. stem bark extract with allopurinol. Materials and Methods: A completely randomized design was used for the experiment which consisted of 6 treatment groups, each consisting of 4 rats, as follows: 1) NR, normal rat; 2) KN, diabetic rat (negative control); 3) KP, diabetic rats given allopurinol 10 mg/kg body weight; 4) EM150, diabetic rats given the test extract 150 mg/kg body weight/day; 5) EM300, diabetic rats given the test extract 300 mg/kg body weight/day; and 6) EM450, diabetic rats given the test extract 450 mg/kg body weight/ day. Results: The results showed that M. calabura L. stem bark extract decrease (p<0.05) uric acid levels in diabetic rats and no specific damage to renal proximal tubular cells was seen. Conclusions: It was concluded that M. calabura L. stem bark extract has a potential as an antihyperuricemic in diabetic rats. The recommended does was 300 mg/kg body weight to provide a significant effect on reducing the uric acid level in diabetic rats. Our findings support the use of this plant as a treatment for gout and other inflammatory diseases.

New analytical solutions of the heat conduction equation are presented in cylindrical and spherical coordinates. Then these solutions are reproduced with high accuracy by recent explicit and unconditionally stable finite difference methods. After this, real experimental data from the literature regarding a heated cylinder are reproduced by the explicit numerical methods as well as by Finite Element Methods (FEM) ANSYS workbench. Convection and nonlinear radiation are also considered on the boundary of the cylinder, and it is shown that the explicit methods are much more accurate than the commercial software.

To better understand the shape memory materials and self-healing materials, a new series of liquid-crystalline shape memory polyurethane (LC-SMPU) composites, named SMPU-OOBAm, were successfully prepared by incorporating 4-octyldecyloxybenzoic acid (OOBA) into the PEG-based SMPU. The effect of OOBA on the structure, morphology and properties has been carefully investigated. The results demonstrate that SMPU-OOBAm have liquid crystalline properties, triple-shape memory properties and self-healing properties. The incorporated OOBA promotes the crystallizability of both soft and hard segments of SMPU, and the crystallization rate of the hard segment of SMPU decreases when the OOBA-content increases. Additionally, the SMPU-OOBAm forms a two-phase separated structure (SMPU phase and OOBA phase), and it shows two-step modulus changes upon heating. Therefore, the SMPU-OOBAm shows triple-shape memory behavior, and the shape recovery ratio decreases with an increase in the OOBA content. Finally, SMPU-OOBAm shows self-healing properties. The new mechanism can be ascribed to the heating-induced “bleeding” of OOBA in the liquid crystalline state and the subsequent re-crystallization upon cooling. This successful combination of liquid crystalline properties, triple-shape memory properties and self-healing properties make the SMPU-OOBAm composites with many promise applications in smart optical devices, smart electronic devices and smart sensors.

Triangular resonators re-shaped with the Sierpinski geometry and U-shaped resonators have been designed, linking them with single-pole-double-through (SPDT) RF MEMS switches to provide frequency tuning for potential applications in the K-Band. Prototypes of band-stop narrowband filters working around 20 GHz and 26 GHz, interesting for RADAR and satellite communications, have been studied in coplanar waveguide (CPW) configuration, and the tuning was obtained by switching between two paths of the devices loaded with different resonators. As a result, dual-band operation or fine-tuning can be obtained depending on the choice of the resonator, acting as a building block. The studied filters belong to the more general group of devices inspired by the metamaterial design.

Berberis vulgaris L. (Berberidaceae) is a shrub that has been widely used in European folk medicine as an anti-inflammatory and antimicrobial agent. The purpose of our study was to elucidate the mechanisms of antiproliferative action of the plant’s methanolic root extract (BVR) against colon cancer cells. Cytotoxicity and pro-apoptotic activity were determined in human colon adenocarcinoma cell lines (LS180 and HT-29) and control colon epithelial CCD841 CoN cells. According to the MTT assay, after 48 h of cell exposure, the IC50 values were as follows: 4.3; 46.1 and 50.2 µg/mL for LS180, HT-29, and CCD841 CoN cells, respectively, showing the greater sensitivity of cancer cells to BVR. The Cell Death Detection ELISAPLUS kit demonstrated that BVR induced programmed cell death only against HT-29 cells. RT-qPCR with relative quantification method showed significant changes in the expression of genes related to apoptosis in both colon cancer cell lines. The genes BCL2L1 (126.84-366.66%), BCL2L2 (277.08-330.12%), CASP3 (180.36-261.36%) and CASP9 (158.08-213.46%) had significantly elevated expression, while BCL2 (23.08-52.06%) had reduced expression. Furthermore, in a panel of antioxidant tests, BVR showed positive effects (63.93±0.01, 122.92±0.01, and 220.29±0.02 mg Trolox equivalents (TE)/g in the DPPH•, ABTS•+ and ORAC assays, respectively). In the lipoxygenase (LOX) inhibition test, BVR revealed 62,60±0.87% of enzyme inhibition. The chemical composition of BVR was determined using UHPLC-UV-CAD-MS/MS analysis and confirmed the presence of several known alkaloids, including berberine, as well as other alkaloids and two derivatives of hydroxycinnamic acid (ferulic and sinapic acid hexosides). This is the first such extensive assessment of the biological activity of BVR. The results are very promising and encourage for the use of BVR as a comprehensive chemopreventive agent (anti-inflammatory, antioxidant, and pro-apoptotic) in colorectal cancer.