Large intelligent surfaces (LIS) promises not only to improve the signal to noise ratio, and spectral efficiency but also to reduce the energy consumption during the transmission. We consider a base station equipped with an antenna array using the maximum ratio transmission (MRT), and a large reflector array sending signals to a single user. Each subchannel is affected by the Rayleigh flat fading, and the reflecting elements perform non-perfect phase correction which introduces a Von Mises distributed phase error. Based on the central limit theorem (CLT), we conclude that the overall channel has an equivalent Gamma fading whose parameters are derived from the moments of the channel fading between the antenna array and LIS, and also from the LIS to the single user. Assuming that the equivalent channel can be modeled as a Gamma distribution, we propose very accurate closed-form expressions for the bit error probability and a very tight upper bound. For the case where the LIS is not able to perform perfect phase cancellation, that is, under phase errors, it is possible to analyze the system performance considering the analytical approximations and the simulated results obtained using the well known Monte Carlo method. The analytical expressions for the parameters of the Gamma distribution are very difficult to be obtained due to the complexity of the nonlinear transformations of random variables with non-zero mean and correlated terms. Even with perfect phase cancellation, all the fading coefficients are complex due to the link between the user and the base station that is not neglected in this paper.

It is expected that scholars will continue to strengthen the depth and breadth of theoretical research on RIS, so as to provide a higher theoretical upper bound for the engineering application of RIS. While making breakthroughs in academic research, great progress has been made in engineering application research and industrialization promotion. This article will provide an overview of RIS engineering applications, mainly including the typical features, typical classifications, and typical deployment scenarios of RIS. Then the challenges and candidate solutions of the RIS are systematically and deeply analyzed, involving the cascade channel decoupling for solving the RIS beamforming, the influences and solutions of RIS regulation constraints, RIS system architecture of network controlled mode, the integrated channel regulation and information modulation, TDD mechanism used for RIS. Future trends and challenges are also provided.

The study aimed to determine the effect of heat stress (HS) on reproductive parameters [calving to first service (CTFS) and first service conception rate (FSCR)] and general physiological responses [rectal temperature (RT) and respiratory rate (RR)] in tropical Holstein Friesian dairy cows raised in Ratchaburi province, Thailand. Cows were divided into a moderate HS (n = 22) and a mild HS (n = 22) group. Cycling cows were detected and injected with PGF2α at the beginning of the experimental period. Reproductive and physiological parameters were recorded. The average temperature humidity indices experienced by the cows were 80.67 ± 0.79 and 77.81 ± 1.09 for the moderate and mild HS groups, respectively. Cows showed significantly lower RT and RR in the mild (38.47 ± 0.21°C and 41.04 ± 4.55 bpm, respectively) than in the moderate HS group (38.87 ± 0.15°C and 51.17 ± 10.52 bpm). Under mild HS, cows showed a better response to injection of PGF2α than those under moderate HS. The percentage of cows that ovulated after being induced by PGF2α and showed estrus signs was higher in the mild than the moderate HS groups (54.55% versus 18.18%). Furthermore, the FSCR of cows under mild HS tended to be higher than in the moderate HS group (54.55 % and 42.11%, respectively), while the average CTFS interval was significantly shorter under mild than moderate HS (69.47 ± 18.18 and 84.60 ± 27.68, respectively). These results indicate that HS impairs reproductive performance in cross-bred Holstein cows, especially in moderate HS conditions.

In this paper, we propose a reconfigurable intelligent surface (RIS) that can dynamically switch the transmission and reflection phase of incident electromagnetic waves in real time to realize the dual-beam or quad-beam and convert polarization of the transmitted beam. Such surfaces can redirect a wireless signal at will to establish robust connectivity when the designated line-of-sight channel is disturbed, thereby enhancing the performance of wireless communication systems by creating an intelligent radio environment. When integrated with a sensing element, they are integral to performing joint detection and communication functions in future wireless sensor networks. In this work, we first analyze the scattering performance of a reconfigurable unit element and then design a RIS. The dynamic field scattering manipulation capability of the RIS is validated by full-wave electromagnetic simulations to realize six different functions. The scattering characteristics of the proposed unit element, which incorporates two p-i-n diodes, have been substantiated through practical implementation. This involved the construction of a simple prototype and the subsequent examination of its scattering properties via the free-space measurement method. The obtained transmission and reflection coefficients from the measurements are in agreement with the anticipated outcomes from simulations.

Dynamic optical structural color is always desired in various display applications and usually involves active materials. Full-color generation, especially bi-directional full-color generation in both reflective and transmissive modes, without any active materials included has been rarely investigated. Herein, we demonstrate a scheme of bi-directional full-color generation based on a plasmonic metasurface modulated by rotation of the polarization angle of the incident light without varying the geometry and the optical properties of the materials and the environment where the metasurface resides. The metasurface unit cell consists of plasmonic modules aligning in three directions and is patterned in a square array. The metasurface structural color device generates full colors in both reflection and transmission. Based on the proposed polarization-dependent structural color, information encoding of three multiplexed animal images and quick-responsive (QR) codes is demonstrated to verify the efficient information encoding and decoding of the proposed scheme. The animals can be seen under different polarization incidence and the QR codes can be successfully decoded by the polarization rotation in transmission. The proposed bi-directional full-color generation metasurface has great potential in applications such as kaleidoscope generation, anti-counterfeiting, dynamic color display, and optical information encoding.

This study aimed to investigate the appearance and frequencies of the booroola polymorphism of the bone morphogenetic protein receptor 1b (BMPR1B) gene (FecB) and the embrapa polymorphism of the growth differentiation factor 9 (GDF9) gene (FecGE) in sheep in Thailand. A total of 454 cross-bred sheep blood samples were collected from four provinces in Thailand during August 2022 to July 2023. The polymerase chain reaction-restriction fragment length polymorphism (PCR-RFLP) method was used to identify the FecB and FecGE genotype. The history of ewe birth types was collected from the owners to analyze the association between Fecundity (Fec) genotypes and the history of birth types. The genotypic frequencies of FecB for homozygous genotype (B/B), heterozygous genotype (+/B) and wild-type (+/+) were 0.22%, 1.54%, and 98.24%, respectively. Meanwhile, the genotypic frequencies of FecGE for homozygous genotype (E/E), heterozygous genotype (+/E), and wildtype (+/+) were 0.00%, 2.42%, and 97.58%, respectively. Furthermore, three ewes exhibited both FecB and FecGE genotypes. Fisher’s exact test revealed that the possessor of FecB genotype was associated with multiple births (p<0.01). Both FecB and FecGE mutations were identified in crossbred sheep in Thailand. Sheep containing FecB allele is a better candidate to be selected to improve the prolificacy of crossbred sheep in Thailand.

The purpose of this paper is to explore the implementation of Retrieval-Augmented Gen- 14 eration (RAG) technology with open-source Large Language Models (LLMs). For this purpose, a 15 web-based application named PaSSER that integrates RAG with three models - Mistral:7b, 16 Llama2:7b: Orca2:7b, is developed. In its development various technologies are used, including 17 Blockchain for managing and storing assessment results of built-in testing modules. PaSSER em- 18 ploys a set of evaluation metrics for LLMs’ performance - METEOR, ROUGE, BLEU, Perplexity, 19 Cosine similarity, Pearson correlation, and F1 score. The specialized knowledge base is in the smart 20 agriculture domain. As an illustration, the paper presents results and analysis of two tests. First one 21 is assessing the performance of LLMs across different hardware configurations, the other is deter- 22 mining the model that delivers most accurate and contextually relevant responses within the RAG. 23 The paper also discusses the integration of blockchain technology with LLMs to manage and store 24 assessment results within a blockchain environment. The tests revealed that Mistral:7b demon- 25 strates the best results across most of the evaluated metrics. The discussion section comments on 26 technical and hardware considerations that affect the performance of LLMs. Future development 27 will focus in leveraging new larger pre-trained open-source LLMs, exploring different finetuning 28 approaches, and further integration with Blockchain and IPFS.

This paper proposes a novel single-stage buck-boost three-Level neutral-point-clamped (NPC) inverter with two independent dc sources coupled for the grid-tied photovoltaic (PV) application, which can effectively solve the unbalanced operational conditions generally appeared between two coupled independent PV sources induced by the unequal irradiation and temperature distribution. The proposed control scheme can simultaneously guarantee the maximum power point (MPP) operation of both PV sources and maintain the output waveform quality. Compared to the traditional two-stage PV inverter, the proposed NPC inverter could reduce the PV array voltage requirement and dc-link capacitors’ voltage rating, meanwhile show the advantage in operational efficiency. MATLAB simulations and the captured experimental results are presented to show the performance of the proposed three-level inverter.

The rapid growth of the global wearable technologies market is projected to reach $61.30 billion by 2030 which reflects a shift towards personalised health monitoring embedded in everyday activities. This paper explores the potential of embroidered interdigitated transducer (IDT)-based sensors for non-invasive, continuous monitoring of human biomarkers, particularly glucose levels, in human sweat. The study employs innovative embroidery techniques to create flexible fabric-based sensors with gold-coated IDTs. Experimental results demonstrate the sensor’s capability to detect water droplets and glucose concentrations, showcasing promising applications for health monitoring. The embroidered IDT-based sensors offer a unique approach for seamless integration into clothing, paving the way for personalised, continuous health data capture.

In this paper, we present an experimental procedure to enhance the dimensional accuracy of fabrication via Stereolithography (SLA) of features at the micro-scale. Using a custom benchmark part, deviations in feature dimensions (micro-pores diameters and depths) were detected and measured by confocal microscopy. Samples characterization and experimental observations allowed the identification of inaccuracy sources, mainly due to the laser beam scanning strategy and to the incomplete removal of uncured liquid resin in post-processing (i.e., IPA washing). As a technology baseline, the measured dimensional errors on pores diameters were up to -46%. A compensation method of the nominal laser spot diameter (85m) was defined and implemented resulting in relevant improvements in dimensional accuracy of 9.8% and 11.3% on full-open pores diameter and depth, respectively. Further investigation was performed on a customized test part to adjust the calibration procedure. The measurements revealed that the estimate of the laser beam spot size is 968m. Measurements on micro-pores having different sizes revealed that a constant compensation parameter (i.e., C=85, 96, 120m) is not fully effective at the micro-scale, where average errors still remain at -24%, -18.8%, and -16% for compensations equals to 85, 96 and 120m, respectively. A further experimental campaign allowed the identification of an effective nonlinear compensation law where the compensation parameter depends on the micro-feature size C= f (D). Results show a sharp improvement in dimensional accuracy on micro-pore fabrication, with errors consistently below +8.2%. The proposed compensation method can be extended for the fabrication of any micro-features without restrictions on the specific technology implementation. Concerning the inaccuracy introduced by the laser path, experimentation with a customized part allowed the optimization of the part orientation to reduce the errors and their differences along the X and Y machine axes.

Timely and accurate information on tree species is crucial for the sustainable management of natural resources, forest inventory, biodiversity detection, and carbon stock calculation. The advancement of remote sensing technology and artificial intelligence has facilitated the acquisition and analysis of remote sensing data, resulting in more precise and effective classification of tree species. Multimodal remote sensing data and deep learning seem to be the current tree species classification research mainstream, whether or not. The current review on the remote sensing data and deep learning tree species classification methods perspectives to analyze the unimodal and multimodal remote sensing data and classification methods in this realm is missing. To bridge the gap, we search for major trends in the remote sensing data and tree species classification methods, provide a detailed overview of classic deep learning-based methods for tree species classification, and discuss the limitations.

Proteomics research has become one of the most important topics in the fields of life science and natural science. At present, research on protein–protein interaction networks (PPINs) mainly focuses on detecting protein complexes or function modules. However, existing approaches are either ineffective or incomplete. In this paper, we investigate function module detection mechanisms in PPIN, including open databases, existing detection algorithms and recent solutions. After that, we describe the proposed solution based on simplified swarm optimization (SSO) algorithm and gene ontology knowledge. The proposed solution implements SSO algorithm for clustering proteins with similar function, and imports biological gene ontology knowledge for further identifying function complexes and improving detection accuracy. Furthermore, we use four different categories of species dataset for experiment: Fruitfly, Mouse, Scere, and Human. The testing and analysis result show that the proposed solution is feasible, efficient and could achieve a higher accuracy of prediction than existing approaches.

Deadlock is a real problem that can cause expensive, time-dependent hang-ups or failures in distributed computing systems. Some studies have been conducted with deadlock detection and resolution in generalized request computing models, most of these studies are based on the diffusing computation scheme, where forward and backward propagated probe and reply messages respectively are diffused between dependent processes. The replies carry the dependency information between processes for the initiator. Using this dependency information initiator can detect and resolve the deadlock cycle. It has been proven in the literature that a deadlock cycle length distribution is skewed with a large majority of cycles (90%) having length two. Based on this fact an improved algorithm is proposed for handling deadlock detection in distributed computing systems under the distributed request model where each process has several requests at a time. The improved algorithm depends mainly on message propagation and timeout policy. Probe and reply messages are propagated between the initiator and its successors only to detect deadlock cycles between them. Global timeout policy is used to detect potential deadlock cycles with large length distribution. The proposed algorithm can handle concurrent executions. Simulation experiments are performed to see the effectiveness of the improved algorithm. It is found that the improved algorithm compares favorably with other existing algorithms and it shows better results for several performance metrics especially in reducing deadlock latency and execution time.

In this study, the on-going research into the improvement of micro-gas turbine propulsion system performance and the suitability for application as propulsion systems for small tactical UAVs (<600 kg) is investigated. The study is focused around the concept of converting existing micro turbojet engines to turbofan with the use of a continuously variable gearbox, thus maintaining a single spool configuration and relative design simplicity. This is an effort to reduce the initial engine development cost, whilst improving propulsive performance. The BMT 120 KS micro turbojet engine is selected for performance evaluation of the conversion process using gas turbine performance software, GasTurb13. The preliminary design of a matched low-pressure compressor (LPC) for the proposed engine is then performed using meanline calculation methods. According to the analysis carried out, an improvement in the converted micro gas turbine engine performance in terms of thrust and specific fuel consumption is achieved. Furthermore, with the introduction of a CVT gearbox, fan speed operation may be adjusted independently of the core, allowing increased thrust generation or better fuel consumption. Therefore, enabling a wider gamut of operating conditions and enhances the performance and scope of tactical UAV.

The hump feature is one of the major instabilities in pump-turbines. When pump-turbines operate in the hump region, strong noise and serious fluctuations can be observed, which are harmful to their safe and stable operation and can even destroy the whole unit as well as water conveyance system. In this paper, a low specific speed (n_q = 36.1 min⁻¹) pump-turbine model was experimentally investigated. Firstly, the hump characteristic was obtained under 19 mm guide vane opening conditions. More interestingly, when the hump characteristic was measured in two directions (increasing and decreasing the discharge), characteristic hysteresis was found in the hump region. The analysis of performance characteristics reveals that the hump instability is the result of Euler momentum and hydraulic losses, and different Euler momentum and hydraulic losses in the two development processes lead to the hysteresis phenomenon. Then, 12 pressure sensors were mounted in the different parts of the pump-turbine model to obtain the time and frequency characteristics. The analysis of the corresponding fast Fourier transform confirms that the hump characteristic is related to low-frequency (0.04–0.15 times rotational frequency) vortices. The occurrence and cessation of vortices depend on the operating condition and measurement direction, which contribute to the hysteresis feature. Finally, the type of the low-frequency vortices was analyzed through the cross power spectrum.

To enhance the applicability of dual-phase high-entropy alloys (HEAs) like Fe32Cr33Ni29Al3Ti3, fabricated via selective laser melting (SLM), a focus on improving their mechanical properties is essential. As part of this effort, heat treatment was explored. This study compares the microstructure and mechanical properties of the as-printed sample with those cooled in water after undergoing heat treatment at temperatures ranging from 1000 to 1200 ℃ for 1 hour. Both pre- and post-treatment samples reveal a dual-phase microstructure comprising FCC and BCC phases. Although heat treatment led to a reduction in tensile and yield strength, it significantly increased ductility compared to the as-printed sample. This strength-ductility trade-off is related to changes in grain sizes with ultrafine grains enhancing strength and micron grains optimizing ductility, also the influence of the content of FCC/BCC phases and dislocation density. In particular, the sample heat-treated at 1000 °C for 1 hour and then water-cooled exhibited a better combination of strength and ductility, a yield strength of 790 MPa, and an elongation of 13%. This research offers innovative perspectives on crafting dual-phase HEA of Fe32Cr33Ni29Al3Ti3, allowing for tailorable microstructure and mechanical properties through a synergistic approach involving SLM and heat treatment.

Bio-molecular reagents like antibodies required in experimental biology are expensive and their effectiveness, among other things, is critical to the success of the experiment. Although such resources are sometimes donated by one investigator to another through personal communication between the two, there is no previous study to our knowledge on the extent of such donations, nor a central platform that directs resource seekers to donors. In this paper, we describe, to our knowledge, a first attempt at building a web-portal titled Bio-Resource Exchange that attempts to bridge this gap between resource seekers and donors in the domain of experimental biology. Users on this portal can request for or donate antibodies, cell-lines and DNA Constructs. This resource could also serve as a crowd-sourced database of resources for experimental biology. Further, in order to index donations outside of our portal, we mined scientific articles to find instances of donations of antibodies and attempted to extract information about these donations at the finest granularity. Specifically, we extracted the name of the donor, his/her affiliation and the name of the antibody for every donation by parsing the acknowledgements sections of articles. To extract annotations at this level, we propose two approaches – a rule based algorithm and a bootstrapped relation learning algorithm. The algorithms extracted donor names, affiliations and antibody names with average accuracies of 57% and 62% respectively. We also created a dataset of 50 expert-annotated acknowledgements sections that will serve as a gold standard dataset to evaluate extraction algorithms in the future. Contact: [email protected], [email protected] Database URL: http://tonks.dbmi.pitt.edu/brx Supplementary information: Supplementary data are available at Database online.

Deep Learning (DL) oriented document processing is widely used in different fields for extraction, recognition, and classification processes from raw corpora of data. The article examines the application of deep learning approaches, based on different neural network methods, including Gated Recurrent Unit (GRU), Long Short-Term Memory (LSTM), and Convolutional Neural Networks (CNN). The compared models were combined with two different word embedding techniques, namely: Bidirectional Encoder Representations from Transformers BERT and Gensim Word2Vec. The models are designed to evaluate the performance of architectures based on neural network techniques for the classification of CVs of Moroccan engineering students at ENSAK(National School of Applied Sciences of Kenitra, Ibn Tofail University). The used dataset included resumes collected from engineering students at ENSAK in 2023 for a project on the employability of Moroccan engineers in which new approaches were applied, especially machine learning, deep learning, and big data. Accordingly, 867 resumes were collected from five specialties of study (Electrical Engineering, Networks and Systems Telecommunications, Computer Engineering, Automotive Mechatronics Engineering, Industrial Engineering). The results revealed good performance of the proposed models based on the BERT embedding approach compared to models based on the Gensim Word2Vec embedding approach. Accordingly, the CNN-GRU/Bert model achieved slightly better accuracy with 0.9251 compared to other hybrid models.

The goal of the study presented in this article is to investigate interconnection issues of the Intelligent Electrical Networks (IENs) with the existing ones, as well as the deployment of the appropriate load forecasting demand techniques. The concept of IENs has recently emerged as a potential solution to the global energy problem, due to the more flexible dispersed production units that are involved. In the same context, additional issues, such as the reduction of production-transfer-distribution costs as well as power losses are analyzed as well, via the penetration of Renewable Energy Sources (RESs). To this end, it is necessary to use appropriate advanced infrastructure, where in combination with modern telecommunication networks will make possible the full exploitation of IENs. Moreover, to make the electricity system more efficient, to avoid voltage and frequency imbalance issues and to implement optimal production and consumption planning, the Electric Load Forecast (ELF) is a vital process and plays a key role in the planning as well as in the management of electricity systems. Therefore, recent state of the art approaches in ELF methods are discussed as well.

This research investigates the complex transformation of the Baltic Clean and Dirty Tankers markets from 1998 to 2023. Our study quantifies the market multifractality in two distinct periods, from 1998 to 2010 and 2010 to 2023. We compare multifractal measures of the original, surrogated, and shuffled data, which indicate high multifractality and a complex market structure influenced by temporal organization and inherent volatility. Shuffled data analysis emphasizes the critical role of temporal sequences within market behaviour. Additionally, the study delves into external factors such as regulatory changes, economic disturbances, technological innovation, and environmental concerns contributing to market complexity. A distinct shift in multifractal values between the two periods suggests an evolution from crisis-induced complexities to a market influenced by diversified and modern dynamics. Our findings offer a concise understanding of the multifractal nature of the tanker markets and how global crises can impact the markets, emphasizing the importance of considering systemic risks in freight market analysis.

This retrospective study aimed to evaluate the performance of the hormone treatment protocols, determine the factors associated with pregnancy success after hormone treatment, and compare the cost-efficiencies of two types of hormone treatment among cyclic and noncyclic anestrous dairy cows. The clinical records of 279 anestrous cows who received hormone treatment for artificial insemination (AI) from 64 herds in the western region of Thailand were obtained from Kasetsart University Veterinary Teaching Hospital from January to August 2017. The performance of the hormone treatment protocols, fixed-time AI (TAI) and estrus detection before AI (EAI), showed that the pregnancy risk for the TAI protocol was higher than for the EAI protocol, but pregnancy per AI did not differ significantly between the two protocols in cyclic and noncyclic cows. Multivariate logistic regression analysis showed that cows receiving the TAI protocol were more likely to be pregnant compared to those treated with the EAI protocol. Cows with a 3.00 body condition score (BCS) &lt;3.75 after treatment and loose-housing cows were more likely to become pregnant. Treatment during winter showed higher pregnancy success than in the summer and rainy seasons. The cost-efficiency analysis showed that the TAI protocol was the most cost-efficient option for noncyclic cows, whereas the EAI protocol was the most cost-efficient option for cyclic cows.

In this paper, the methodology using Insect Intelligent Building (I^2B) technology for establishing energy consumption monitoring system of public buildings is prevailed. The computing process node and distributed algorithm are utilized to implement the energy consumption collection and data transmission and data pre-processing. Taking a commercial building as a case study, CPNs are applied to set up the building energy consumption monitoring system, with the Spanning Tree Algorithm for generating network topology，and BPNN method for solving abnormal data and recovering missing data. The research results demonstrate the proposed method can effectively improve the performance of plug-and-play and self-identified and self-configuration of energy consumption monitoring system.

This work presents a novel approach for the study of the movement of droplets on inclined surfaces under the influence of gravity and chemical heterogeneities. The developed numerical methodology uses data-driven modeling to extend the applicability limits of an analytically derived reduced-order model for the contact line velocity. More specifically, while the reduced-order model is able to capture the effects of the chemical heterogeneities to a satisfactory degree, it does not account for gravity. To alleviate this shortcoming, datasets generated from direct numerical simulations are used to train a data-driven model for the contact line velocity, which is based on the Fourier neural operator and corrects the reduced-order model predictions to match the reference solutions. This hybrid surrogate model, which comprises of both analytical and data-driven components, is then integrated in time to simulate the droplet movement, offering a speedup of five orders of magnitude compared to direct numerical simulations. The performance of this hybrid model is quantified and assessed in different wetting scenarios, by considering various inclination angles and values for the Bond number, demonstrating the accuracy of the predictions as long as the adopted parameters lie within the ranges considered in the training dataset.

The Dph1•Dph2 heterodimer from yeast is a radical SAM (RS) enzyme that generates the 3-amino-3-carboxy-propyl (ACP) precursor for diphthamide, a clinically relevant modification on eukaryotic elongation factor 2 (eEF2). ACP formation requires SAM cleavage and atypical Cys-bound Fe-S clusters in each Dph1 and Dph2 subunit. Intriguingly, the first Cys residue in each motif locates next to another, ill-defined cysteine that we show in-here is conserved across eukaryotes. As judged from structural modeling, the orientation of these tandem cysteine motifs (TCM) suggests a candidate Fe-S cluster ligand role. Hence, we generated by site-directed DPH1 and DPH2 mutagenesis, Dph1•Dph2 variants with cysteines from each TCM replaced individually or in combination by serines. Assays diagnostic for diphthamide formation in vivo reveal that while single substitutions in the TCM of Dph2 cause mild defects, double mutations almost entirely inactivate the RS enzyme. Based on enhanced Dph1 and Dph2 subunit instability in response to cycloheximide chases, the variants with Cys substitutions in their cofactor motifs are particularly prone to protein degradation. In sum, we identify a fourth functionally cooperative Cys residue within the Fe-S motif of Dph2 and show that the Cys-based cofactor binding motifs in Dph1 and Dph2 are critical for the structural integrity of the dimeric RS enzyme in vivo.

In this paper, we introduce a new formulation based on Floquet (Fourier) spectral analysis combined with a spectral modulation technique (and its spatial form) to study strongly coupled sublattices predefined in the infinite and large finite extent of almost periodic antenna arrays (e.g metasurfaces). This analysis is very relevant for dense massive MIMO, intelligent surfaces, 5G, and 6G applications (used for very small areas with a large number of elements such as millimeter and terahertz waves applications). The numerical method that is adopted to model the structure is the method of moments simplified by equivalent circuits MoM GEC. Other numerical methods (as the ASM array scanning method and windowing Fourier method) used this analysis in their kernel that to treat periodic and pseudo-periodic (or quasi-periodic) arrays.

Depth-sensing technology has led to broad applications of inexpensive depth cameras that can capture human motion and scenes in 3D space. Background subtraction algorithms can be improved by fusing color and depth cues, thereby allowing many issues encountered in classical color segmentation to be solved. In this paper, we propose a new fusion method that combines depth and color information for foreground segmentation based on an advanced color-based algorithm. First, a background model and a depth model are developed. Then, based on these models, we propose a new updating strategy that can eliminate ghosting and black shadows almost completely. Extensive experiments have been performed to compare the proposed algorithm with other, conventional RGB-D algorithms. The experimental results suggest that our method extracts foregrounds with higher effectiveness and efficiency.

With the development of higher voltage power grid, the high and low voltage parallel loops are emerging, which lead to energy losses, even threaten the security and stability of power system. The multi-infeed HVDC configurations widely appearing in AC/DC interconnected power system make this situation even worse. Aimed at energy saving and system security, a decision optimization method for power grid operating condition with high and low voltage parallel loops is proposed in this paper. Firstly, considering hub substation distribution and power grid structure, parallel loop opening schemes are generated with GN algorithm. Then, candidate opening schemes are preliminarily selected from all these generated schemes based on a filtering index. Finally, with the influence on power system security, stability and operation economy in consideration, an evaluation model for candidate opening schemes is founded based on analytic hierarchy process (AHP). And a fuzzy evaluation algorithm is used to find the optimal scheme. Simulation results of New England 39-bus system and an actual power system validate the effectiveness and superiority of this proposed method.

Ti and its alloys are the most commonly used materials for biomedical applications. However, bacterial infection after implant placement is still one of the significant rising complications. Therefore, the application of the antimicrobial agents into implant surfaces to prevent implant-associated infection has attracted lots of attention. Scientific papers have shown that inorganic antibacterial metal element (e.g. Ag, Cu, Zn) can be introduced to implant surfaces with the addition of metal nanoparticles or metallic compounds into electrolyte via micro-arc oxidation (MAO) technology. In this review, the effects of the composition and concentration of electrolyte and process parameters (e.g. voltage, current density, oxidation time) on morphological characteristics (e.g. surface morphology, bonding strength), antibacterial ability and biocompatibility of MAO antimicrobial coating were discussed in detail. Anti-infection and osseo-integration can be simultaneously accomplished with the selection of the proper antibacterial elements and operating parameters. Besides, MAO assisted by magnetron sputtering (MS) to endow Ti-based implant materials with superior antibacterial ability and biocompatibility was also discussed. Finally, the development trend of MAO technology in the future was forecasted.

With continuous increase in integration of the semiconductor devices, the requirements on size accuracy and surface quality of the etched lead frame are higher. The etchant is a key factor on etching process and etched surface quality, while effects of the difference in etchants on microscopic etched surface morphology of the Cu alloy have not been directly studied. In this study, the aqua regia, acidic FeCl3 and CuCl2 solutions were used as etchants, and the CuCrSn alloy specimens with different microstructure were etched and characterized. The results show that the etching rate in aqua regia is high, and the grain orientation, grain boundary (GB) and dislocation have significant influence on the local etching rate. The preferential etching of some atomic planes forms steps between grains with different orientations, and the preferential etching around the GB and dislocation group forms grooves, resulting in high surface roughness. For etching of the FeCl3 and CuCl2 etchants, the steps and grooves become blurred, and almost invisible on the surface etched by the CuCl2 etchant, thus the surface roughness is much lower. The CuCrSn alloy surface etched by the aqua regia is clean, with little Cr-rich particles, while high density Cr-rich particles are remained on the surfaces etched with the FeCl3 and CuCl2 etchants. For the same kind of etchant, the ion concentration can affect the etching mechanism and etching surface morphology.

In the recent years, tubular nanostructures have been related with immense advances in various fields of science and technology. Considerable research efforts have been centered on the theoretical prediction and manufacturing of non-carbon nanotubes (NTs), which meet modern requirements for the developing of novel devices and systems. In this context, diatomic inorganic nanotubes formed by atoms of elements from the 13th group of the periodic table (B, Al, Ga, In, Tl) and nitrogen (N), have received much research attention. In the present work, the elastic properties of single-walled boron nitride, aluminium nitride, gallium nitride, indium nitride and thallium nitride nanotubes were numerically evaluated using the nanoscale continuum modelling approach (also called molecular structural mechanics). The elastic properties (rigidities, surface Young´s and shear moduli, and Poisson´s ratio) of nitride nanotubes are discussed with respect to the bond length of the corresponding diatomic hexagonal lattice. The results obtained contribute to a better understanding of the mechanical response of nitride compound-based nanotubes, covering a broad range from the well-studied boron nitride NTs to the hypothetical thallium nitride NTs.

The IEEE 802.11ah standard is introduced to address the growing scale of Internet of Things (IoT) applications. To reduce contention and enhance energy efficiency within the system, the restricted access window (RAW) mechanism is introduced at the medium access control (MAC) layer to manage the significant number of stations accessing the network. However, the RAW parameters need to be appropriately determined to achieve optimal network performance. In this paper, we optimize the configuration of RAW parameters in the IEEE 802.11ah-based IoT network. We analyze and propose an RAW parameters optimization problem with the objective of improving network throughput and formulate it as a Markov decision process. To cope with the complex and dynamic network conditions, we propose a proximal policy optimization (PPO)-based deep reinforcement learning (DRL) algorithm to find the optimal RAW parameters. We construct network environments with periodic and random traffic in the NS-3 simulator to validate the performance of the proposed PPO-based RAW parameters optimization algorithm. Simulation results reveal that using the PPO-based DRL algorithm, optimal RAW parameters can be obtained under different network conditions, thereby significantly improving network throughput.

The invasion of ship domain stands out as a significant factor contributing to the risk of collisions during vessel navigation. However, there is a lack of research on the mechanisms underlying collision risks specifically related to merchant and fishing vessels in coastal waters. This study proposes an assessment method for collision risks between merchant and fishing vessels in coastal waters and validated through a comparative analysis through visualization. First of all, the operational status of fishing vessels is identified. Collaboratively working fishing vessels are treated as a unified entity, expanding their ship domain during operation to assess collision risks. Secondly, to quantify the collision risk between ships, a collision risk index (CRI) is proposed and visualized based on the severity of collision risk. Finally, taking the high risk area of merchant and fishing vessels collision in the Minjiang River Estuary as an example, this paper conduct the analysis involves classifying ship collision scenarios, extracting risk data under different collision scenarios, and visually analyzing areas prone to danger. The results indicate that this method effectively evaluates the severity of collision risk, and the identified high-risk areas resulting from the analysis is verified by accidents occurred in the recent three years.

Endoscopy has made a significant and noteworthy contribution to the field of medical science and technology. Nevertheless, its potential remains constrained due to the limited availability of rigid or flexible endoscopes. This paper introduces a novel hydraulic actuator based on electrorheological fluid (ERF) as a pivotal advancement in bridging the existing gap within the realm of endoscopy. Following a comprehensive introduction that briefly outlines the electrorheological effect, the subsequent section is dedicated to the elucidation of the actuator’s development process. Challenges arise, particularly in terms of miniaturization and the realization of a hydraulically sealed system with integrated valve electrodes. An internal electrorheological valve system consisting of four valves that are controlled using a pulse-width modulated high voltage was suitable for position control of the antagonistic hydraulic actuators. High-precision stereolithography (SLA) printing has proven practical for manufacturing the actuator components. For functional testing, a test bench was set up in which the actuator follows a setpoint through a PI control loop. The control deviation ranged from 0.6 to 1 degree, with a response time between 6 and 8 seconds. The experiments have demonstrated that, through the use of ERF and integrated valve electrodes, a miniaturized functional actuator can be constructed.

Background: Microscopic examination of acid-fast stained sputum smears for detecting mycobacterial acid-fast bacilli (AFB) remains the most economical and readily available method for laboratory diagnosis of tuberculosis (TB). However, this conventional approach has limitations, including low sensitivity and labor-intensive procedures. Methods: An automated microscopy system incorporating artificial intelligence (AI) and machine learning for AFB identification was evaluated. The study was conducted at an Infectious Disease Hospital in Jiangsu Province, China, utilizing an intelligent microscope system (TB-Scan, Wellgen Medical, Kaohsiung). A total of 1,000 sputum smears were included in the analysis, with the system capturing digital microscopic images and employing an image recognition model to automatically identify and classify AFB. Referee technicians provided the gold standard for discrepant results. Results: The automated system demonstrated an overall accuracy of 95.00% (950/1,000), sensitivity of 91.24% (177/194), and specificity of 95.91% (773/806). Notably, the system identified 21 smears as positive that were previously reported as negative, with referee technicians confirming 17 of these as true positive and retracting the test results accordingly. Recalculating the performance, the accuracy increased to 96.70% (967/1,000), sensitivity to 91.94% (194/211), and specificity to 97.97% (773/789), with a false negative rate of 8.06% (17/211) and a false positive rate of 2.03% (16/789). Conclusions: The incorporation of AI and machine learning into an automated microscopy system demonstrated the potential to enhance the sensitivity and efficiency of AFB detection in sputum smears compared to conventional manual microscopy. This approach holds promise for widespread application in TB diagnostics and potentially other fields requiring labor-intensive microscopic examination.

To conduct high-precision and high-resolution numerical simulation of complex flow structures in turbomachinery, a high-order finite volume weighted essentially non-oscillatory (WENO) scheme for the large eddy simulation (LES) is improved and embedded into the three-dimensional viscous unsteady CFD solver NUAA-Turbo. Firstly, the spectral characteristics and unsteady convergence of the improved WENO scheme are studied. Compared with the classical WENO scheme, the improved WENO scheme has better dissipation and dispersion characteristics and faster convergence speed. Then, the coefficient CW of the Wall-Adapting Local Eddy-viscosity (WALE) model is calibrated by decaying homogeneous isotropic turbulence (DHIT) test case. Finally, the scheme is applied to conduct high-precision LES calculations of turbulent boundary layer flow, supersonic compression corner flow, and low-pressure turbine cascade separation flow. The numerical simulation results show that this WENO scheme has excellent shock wave capture ability and turbulence resolution and can capture more flow field details with less mesh size, greatly reducing the computational cost and laying a foundation for large-scale engineering application of LES.

Loneliness is becoming prevalent across Japan in spite of its a dense population and communal culture. Surveys show 40% of adults report isolation across demographics. The contradiction emerges due to deteriorating social structure with modernization, economic parity, urbanization, and fading conventional setup. The continually social withdrawals, called “hikikomori." Relief seekers have embraced AI based emotive robots, digital avatars, and immersive VR as low-stakes social surrogates despite limited capacity to cultivate human intimacy. To stabilise government attempts awareness through reforms, scheme and support services. But a concrete transformation can be brough in with work-life balance, gender equality and rewire the metrics for self-esteem. Even a perfectly personalized AI cannot replace the human affection lacking in the society. Lasting solutions demand technological aids be balanced by confronting and reinventing community purpose and bring in structural change. Overall Japan’s endemic isolation reveals the societal fraying when modernization privileges independence over interdependence. The path forward rests on restoring cultural foundations to reverse loneliness and social isolation.

In this paper, we studied the problem of early detection of natural phenomena associated with the formation of severe floods and the possibility of constant monitoring of their occurrence. The test object for the study was severe floods on the Crimean Peninsula, which occurred due to heavy rainfall in the summer of 2021. Based on the selected satellite and other data related to this period, an analysis carried out and key atmospheric objects identified, according to the proposed algorithm for their identification and grouping. Based on the results of the work, a positive conclusion made on the issue of their use to identify the likelihood of natural disasters that could lead to floods. In addition, the authors proposed to develop a portal for collecting and processing a large amount of satellite data related to flood prevention and monitoring the development of such processes, and stressed the need to create it.

The attitude dynamics and orbit dynamics of large rigid space structures are coupled with each other under gravity gradient, which may affect the stability of the large rigid space structures. In this paper, the gravity gradient stability of a large rigid space structure is studied under both small and large disturbances. Based on the rigid body dynamics and orbit dynamics, an accurate dynamic model without any linearization of the large rigid space structure is established via the natural coordinate formulation (NCF), which is able to describe the large overall motions of the structures. By using the generalized-α algorithm, the gravity gradient stability of the large rigid space structure is simulated and analyzed via various examples, including the influence of large disturbance angles, the positions at the stabilization and unstabilization regions. Finally, the relationship between spinning stability and gravity gradient stability is also investigated via a large spinning space structure.

In this paper, we first discuss the research status and application progress of the finite element method and the smoothed particle method. By analyzing the advantages of the smoothed particle method and the finite element method, a new coupling algorithm, namely FEM-SPH algorithm, is proposed. By the method of comparison, it shows that finite element method and SPH method in the simulation of large deformation problems each have advantages and disadvantages, the finite element method smoothed particle coupling algorithm is effective to achieve the performance of high computational efficiency and can naturally simulate large deformation problems across. In the process of calculation, the large deformation unit can be freely into an algorithm to facilitate the calculation accuracy and efficiency of three methods of numerical simulation. Through the study found, FEM-SPH algorithm not only overcome the defect of smooth particle tensile instability, but also overcomes the problem of low efficiency of finite element computation. To further test the FEM-SPH algorithm has advantages in the practical engineering, we have carried out the actual test to the example of the super high speed collision, concluded that, since the target of most of the computational domain is always finite element, smoothed particle focused only in contact with the projectile and target of local area, particle number is not much, the whole calculation process just ten minutes, computational efficiency has been greatly improved, at the same time in the simulation of large deformation, the advantage is very obvious .This provides a criterion for the actual project, depending on the specific material deformation mode and choose a more appropriate conversion algorithm.

The article suggests methods that allow creating the most complicated type of polygonal masonry found in Peru. This masonry type consists of large stone blocks weighing from several hundred kilograms to several tons fitted close to each other almost without a gap between complicated curved surfaces over a large area. The work provides a description of techniques, which apparently were used by builders who arrived from Europe. The techniques under discussion are based on the use of a reduced clay model, 3D-pantograph, topography translator and replicas. The use of the topography translator, reduced clay model and pantograph provides not only the unique appearance and high quality of masonry of large blocks, but also allows to increase the productivity of the builders significantly. As machines coping-scaling three-dimensional objects are known since the beginning of the 18th century, the stone structures under consideration should be approximately dated by this time. The remaining simpler types of polygonal masonry, when the stones are small or the fitted surfaces are almost flat, or the stones contact each other over a small area, or there are significant gaps between the stones, are quite consistent with the well-known methods of stone processing at that time or earlier, and, therefore, they do not require any additional explanations. The Fortress Sacsayhuaman is considered as an example of early star fortresses that has survived to our time. The polygonal structures in Peru, the polygonal Face Towers and polygonal bas-reliefs in Cambodia, symmetrical statues of pharaohs in Egypt are based on the same construction technologies, working methods, tools and technical contrivances. Therefore, with a high probability one can state that all these monuments were created by the same group of architects, sculptors, builders, and could not have appeared before the 17th century.

Compared with conventional methods of fault diagnosis for power transformers, which have defects such as imperfect encoding and too absolute encoding boundaries, this paper systematically discusses various intelligent approaches applied in fault diagnosis and decision making for large oil-immersed power transformers based on dissolved gas analysis (DGA), including expert system (EPS), artificial neural network (ANN), fuzzy theory, rough sets theory (RST), grey system theory (GST), swarm intelligence (SI) algorithms, data mining technology, machine learning (ML), and other intelligent diagnosis tools, and summarizes existing problems and solutions. From this survey, it is found that a single intelligent approach for fault diagnosis can only reflect operation status of the transformer in one particular aspect, causing various degrees of shortcomings that cannot be resolved effectively. Combined with the current research status in this field, the problems that must be addressed in DGA-based transformer fault diagnosis are identified, and the prospects for future development trends and research directions are outlined. This contribution presents a detailed and systematic survey on various intelligent approaches to faults diagnosing and decisions making of the power transformer, in which their merits and demerits are thoroughly investigated, as well as their improvement schemes and future development trends are proposed. Moreover, this paper concludes that a variety of intelligent algorithms should be combined for mutual complementation to form a hybrid fault diagnosis network, such that avoiding these algorithms falling into a local optimum. Moreover, it is necessary to improve the detection instruments so as to acquire reasonable characteristic gas data samples. The research summary, empirical generalization and analysis of predicament in this paper provide some thoughts and suggestions for the research of complex power grid in the new environment, as well as references and guidance for researchers to choose optimal approach to achieve DGA-based fault diagnosis and decision of the large oil-immersed power transformers in preventive electrical tests.

Public restrooms are often a hub of microbial contamination, and the examination of bacterial contamination in these facilities can serve as an important indicator of the transmission of infectious diseases. This study was conducted to determine the prevalence of bacterial contamination in public restrooms based on the economic class of the building. Samples were collected from various spots in 32 restrooms found in 10 shopping malls, classifying them into two categories: upper-end restrooms and lower-end restrooms. The findings showed that the level of contamination was higher in the lower-end restrooms, with the seat being the most contaminated area. The most dominant Gram-positive bacteria were coagulase-negative staphylococci species, making up 86% of the identified Gram-positive isolates. The most dominant Gram-negative bacteria identified were Klebsiella pneumoniae and Pseudomonas aeruginosa. The antibiotic sensitivity test results revealed the presence of multi-drug resistant bacteria among the Gram-positive and negative isolates, including Staphylococcus haemolyticus, Staphylococcus kloosi, Acinetobacter baumanii, and Pseudomonas aeruginosa. In conclusion, the study underscores the significance of monitoring bacterial contamination in public restrooms and the need for measures to reduce the spread of infectious diseases. Further research is crucial to gain a complete understanding of the bacterial contamination in public restrooms and their resistance patterns, to ensure the safety and health of the public. The implementation of improved cleaning practices and hands-free designs in restrooms can help reduce the risk of cross-contamination and prevent the spread of diseases.

In wireless sensor networks (WSNs), each sensor node can estimate the global parameter from the local data in distributed manner. This paper proposed a robust diffusion estimation algorithm based on minimum error entropy criterion with self-adjusting step-size, which are referred to as diffusion MEE-SAS (DMEE-SAS) algorithm. The DMEE-SAS algorithm has fast speed of convergence and is robust against non-Gaussian noise in the measurements. The detailed performance analysis of the DMEE-SAS algorithm is performed. By combining the DMEE-SAS with diffusion minimum error entropy (DMEE) algorithms, an Improving DMEE-SAS algorithm is proposed, in non-stationary environment where tracking is very important. The Improving DMEE-SAS algorithm can avoid insensitivity of the DMEE-SAS algorithm due to the small effective step-size near the optimal estimator, and obtain a fast convergence speed. Numerical simulations are given to verify the effectiveness and advantages of these proposed algorithms.

The increasing availability of longitudinal data (repeated numerical observations of same units at different times) requires the development of flexible techniques to automatically detect common errors in such data. Besides obvious and easily identifiable cases, such as missing or out-of-range data, large longitudinal dataset often present problems not easily traceable by the techniques used for generic datasets. In particular, elusive and baffling problems are i) inversion of one or more values from one unit to another; ii) anomalous jumps in the series of values, iii) errors in the timing of the values due to a recalculation operated by the data providers to compensate previous errors. This work proposes a statistical-mathematical approach based on a system of indicators that is able to capture the complexity of the described problems by working at the formal level, regardless of the specific meaning of the data. The proposed approach identifies suspect erroneous data and is applicable in a variety of contexts. We implement this approach in a relevant database of European Higher Education institutions (ETER) by analyzing Total academic staff, that is one of the most important variables, used in empirical analysis as proxy of size and also considered by policy makers at European level.

Sixteen crossbred rabbits (New Zealand white x Thai native breed) were randomly divided into two groups of eight to determine the effects of daily oral administration of crude extracts from the butterfly pea (Clitoria ternatea L.) from weaning (at 35 days) to slaughter (at 90 days). Effects on phagocytic activity of blood polymorphoneuclear leukocytes, serum biochemistry, meat quality, muscular lipid peroxidation, apparent digestibility, and gut histology were studied. The results revealed that the phagocytic function of circulating leukocytes (75 and 90 days) and alveolar macrophages (90 days) did not differ between the two groups. At slaughter, treated rabbits had lower blood urea nitrogen concentrations and higher liver weight than control rabbits (p &lt; 0.05). After chilling at 4°C for 24 hours, lower meat pH and alteration of meat color (a brighter, less yellow, Hue angle and color saturation) were observed in the treated group (p &lt; 0.05). Furthermore, lipid peroxidation (measured at 3, 5 and 7 storage days) in the meat of treated rabbits was lower than in controls (p &lt; 0.05). Apparent digestibility (analyzed at 46 days for four days) revealed improved organic matter and ether extracts in the treated group (p &lt; 0.05), whereas gut histology was unaffected. In conclusion, butterfly pea extract supplementation did not affect phagocytic function but led to a modification in meat color, delayed lipid peroxidation, and improved digestibility.

This study aimed to evaluate the impact of Candida albicans on subgingival biofilm formation on dental implant surfaces. Scanning electron microscopy (SEM) and confocal laser scanning microscopy (CLSM) were used to compare biofilm structure and microbial biomass in the presence and absence of the fungus after periods of 24, 48, and 72 h. Quantitative polymerase chain reaction (qPCR) was used to quantify the number of viable and total micro-organisms for each of the biofilm-forming strains. A general linear model was applied to compare CLSM and qPCR results between control and test conditions. The biofilm developed with C. albicans at 72 h had a higher bacterial biomass, with a significantly higher cell viability (p &lt; 0.05). After both 48 and 72 h of incubation, in the presence of C. albicans, there was a significant increase in counts of Fusobacterium nucleatum and Porphyromonas gingivalis and in the cell viability of Streptococcus oralis, Aggregatibacter actinomycetemcomitans, F. nucleatum, and P. gingivalis. Using a dynamic in vitro multispecies biofilm model, C. albicans exacerbated the development of the biofilm grown on dental implant surfaces, significantly increasing the number and cell viability of periodontal bacteria.

Underwater image often exhibit detail blurring and color distortion due to light scattering, impurities, and other influences, obscuring essential textures and details. This presents a challenge for existing super-resolution techniques in identifying and extracting effective features, making high-quality reconstruction difficult. This research aims to innovate underwater image super-resolution technology to tackle this challenge. Initially, an underwater image degradation model was created by integrating random subsampling, Gaussian blur, mixed noise, and suspended particle simulation to generate a highly realistic synthetic dataset, thereby training the network to adapt to various degradation factors. Subsequently, to enhance the network's capability to extract key features, improvements were made based on the symmetrically structured Blind Super-Resolution Generative Adversarial Network (BSRGAN) model architecture. An attention mechanism based on energy functions was introduced within the generator to assess the importance of each pixel, and a weighted fusion strategy of adversarial loss, reconstruction loss, and perceptual loss was utilized to improve the quality of image reconstruction. Experimental results demonstrate that the proposed method achieved significant improvements in Peak Signal-to-Noise Ratio (PSNR) and Underwater Image Quality Measure (UIQM) by 0.85 dB and 0.19, respectively, significantly enhancing the visual perception quality and indicating its feasibility in super-resolution applications.

External hoof characteristics, balance, and conformation have been extensively studied in horses; however, mules remain understudied in these aspects. This study evaluated the size, shape, and symmetry of untrimmed and unshod forelimb hooves, compared the symmetry between forelimb hooves and stratified external forelimb hoof measurements based on the body condition score of mules raised in the foothill plains of northern Thailand. The forelimb hooves of 38 mules were photographed and 33 parameters, including angular and linear measurements, were analyzed. Despite the absence of shoeing and trimming, these mules exhibited optimal left-right forelimb hoof symmetry, with no significant (p < 0.05) differences in: outer wall length and inner wall length (OWL - IWL); sole length and sole width (SLS - SW); dorsal hoof wall length and heel length (DHWL - HL); and frog length and frog width (FL - FW). However, significant (p < 0.05) differences were observed within each body condition score group for forelimb hoof measurements for DHWL, IWL, heel separation (HS), heel bulb distance (HBD), SW, FW, and FL. These findings provide valuable insights into mule welfare and management, contributing to understanding of the interplay between overall health and hoof conformation in the study area.

Underwater visual detection technology plays a pivotal role in fields such as marine exploration. With the increasing demand for underwater monitoring, the quest for efficient and reliable methods for underwater target recognition has become particularly significant. To address this requirement, this study developed an innovative underwater object detection architecture based on YOLOv8, named YOLOv8-MU, aimed at significantly enhancing detection accuracy.By integrating the LarK module proposed in UniRepLKNet to optimize the backbone network, YOLOv8-MU aims to achieve a larger receptive field without increasing the model’s depth. Further, this research introduces C2fSTR, an innovative method that combines Swin Transformer with the C2f module. Additionally, we have incorporated the SPPFCSPC_EMA module, which combines Cross-Stage Partial Fast Spatial Pyramid Pooling (SPPFCSPC) with attention mechanisms, significantly improving the detection accuracy and robustness of various biological targets. Moreover, by introducing a fusion block based on DAMO-YOLO into the neck of the model, we further enhanced the model’s capability in multi-scale feature extraction. Finally, the adoption of the MPDIoU loss function, designed around vertex distance, effectively tackles the challenges of localization accuracy and boundary clarity in underwater organism detection. Experimental results on the URPC2019 dataset demonstrate that the YOLOv8-MU model achieved an [email protected] of 78.4%, marking improvements of 5.6%, 1.1%, and 4.0% over YOLOv5s, YOLOv7, and YOLOv8n respectively, indicating the leading performance (SOTA) of this method. On the other hand, further evaluation on the URPC2020 dataset confirmed the generalization capability of the YOLOv8-MU architecture, with its [email protected] reaching 80.4%, surpassing various models including YOLOv5x and YOLOv8n, showcasing the wide applicability of our proposed improved model architecture.

The scientific community has shown considerable interest in Industry 4.0 due to its capacity to revolutionise the manufacturing sector through digitalisation and data-driven decision-making. However, the actual implementation of Industry 4.0 within complex industrial settings presents obstacles that are typically beyond the scope of mainstream research articles. In this paper, a comprehensive case-study detailing our collaborative partnership with a leading medical device manufacturer is presented. The study traces their evolution from a state of limited digitalisation to the development of a digital intelligence platform that leverages data and machine learning models to enhance operations across a wide range of critical machines and assets. The main business objective was to enhance the energy efficiency of the manufacturing process, thereby improving its sustainability measures while also saving costs. The project encompasses energy modelling and analytics, Fault Detection and Diagnostics (FDD), renewable energy integration and advanced visualisation tools. Together, these components enable informed decision making in the context of energy efficiency.

Compressed carbon dioxide energy storage (CCES) offers several benefits over other existing energy storage systems, including ease of liquefaction, high energy storage density, and environmental friendliness. As a result, the research progress, economic and technological feasibility, and system operation of the CCES system are all discussed in depth in this study. The system evaluation method is summarized and the compressed carbon dioxide storage is analyzed, and the performance optimization direction of the compressed carbon dioxide energy storage technology is discussed. When the overall performance of a transcritical CCES system, a supercritical CCES system and a liquid CCES system are compared, it is discovered that the supercritical CCES system has better thermodynamic characteristics and a simpler system configuration, making it suitable for large-scale development and use. The goal of the CCES system's future development is to create a design with an optimum compression and expansion ratio, a more precise analysis and system model, and multi-field coupling. This review's discussion serves as a guide for the best design and use of the CCES system.

The main purpose of this article is to identify brain diseases such as Alzheimer's and Parkinson's in an intelligent way using Python software and processing the function of neurons in the neural network areas of the brain, which are classified into different components, and the data is based on the information obtained from FMRI images using algorithms artificial intelligence can intelligently diagnose the type of disease. Therefore, by using spatial clustering based on the deep learning method with noise algorithm (DBSCAN), fMRI brain image and fMRI brain surface complexity are classified, and then image preprocessing will be applied to fMRI images by using artificial intelligence neural networks (ANN) algorithm. became. Then, by using the ANN algorithm and Deep CNN topology of the brain neural network, the type of disease in the brain can be diagnosed by simulating the performance of an artificial neural network (ANN) in Python software. Deep machine learning-based methods, especially algorithms based on neural networks, have shown great success in medical image analysis for various tasks including brain tumor detection, segmentation, and classification, and Alzheimer's and epilepsy. In this research, we propose an integrated model based on a convolutional neural network for simultaneous recognition and classification of brain diseases for intelligent diagnosis of tumors and epilepsy. The average accuracy obtained from our proposed model is 97.89 percent accuracy and 91.66 percent specificity.

Surface water distribution extracted from remote sensing data has been used in water resource assessment, coastal management, and environmental change studies. Traditional manual methods for extracting water bodies cannot satisfy the requirements for mass processing of remote sensing data; therefore, accurate automated extraction of such water bodies has remained a challenge. The histogram bimodal method (HBM) is a frequently used objective tool for threshold selection in image segmentation. The threshold is determined by seeking twin peaks, and the valley values between them; however, automatically calculating the threshold is difficult because complex surfaces and image noise which lead to not perfect twin peaks (single or multiple peaks). We developed an operational automated water extraction method, the modified histogram bimodal method (MHBM). The MHBM defines the threshold range of water extraction through mass static data; therefore, it does not require the identification of twin histogram peaks. It then seeks the minimum values in the threshold range to achieve automated threshold. We calibrated the MHBM for many lakes in China using Landsat 8 Operational Land Imager (OLI) images, for which the relative error (RE) and squared correlation coefficient (R2) for threshold accuracy were found to be 2.1% and 0.96, respectively. The RE and root-mean-square error (RMSE) for the area accuracy of MHBM were 0.59% and 7.4 km2. The results show that the MHBM could easily be applied to mass time-series remote sensing data to calculate water thresholds within water index images and successfully extract the spatial distribution of large water bodies automatically.

Natural language Processing (NLP) has significantly transformed in the last decade, especially in the field of Language Modeling. Large Language Models (LLMs) have achieved SOTA performances on Natural Language Understanding (NLU) and Natural Language Generation (NLG) tasks by learning language representation in self-supervised ways. This paper provides a comprehensive survey to capture the progression of advances in Language Models. In this paper, we examine the different aspects of Language Models, which started with a few million parameters but have reached the size of a trillion in a very short time. We also look at how these LLMs transitioned from task-specific to task-independent to task-and-language-independent architectures. This paper extensively discusses different pre-training objectives, benchmarks, and transfer learning methods used in LLMs. It also examines different fine-tuning and In-Context learning techniques used in downstream tasks. It also explores how LLMs can perform well across many domains and datasets if sufficiently trained on a large and diverse dataset. Next, it discusses how, over time, the availability of cheap computational power and large datasets have improved LLM’s capabilities and raised new challenges. As part of our study, we also inspect LLMs from the lens of scalability to see how their performance is affected by the model’s depth, width, and data size. Lastly, we provide an empirical comparison of existing trends and techniques and a comprehensive analysis of where the field of LLM currently stand.

The study evaluated potassium peroxymonosulfate (PPMS) efficacy against rifampicin-resistant Salmonella Infantis (rif-SI), Escherichia coli (E. coli), Salmonella Infantis (SI), Newcastle disease virus (NDV) and avian influenza virus (AIV). The assessment encompassed varied concentrations, organic material conditions, and exposure durations to comprehensively evaluate PPMS efficacy. Moreover, PPMS’s efficacy was tested on diverse carrier surfaces and clothing to evaluate its bactericidal and virucidal potential. At the recommended concentrations (1X), PPMS effectively inactivated all pathogens within 5 sec, except for NDV, which required 30 sec in the presence of organic materials. At 0.5X, PPMS successfully inactivated E. coli, AIV and NDV within 5 sec in the absence of organic material. However, rif-SI and SI necessitated 30 sec for inactivation. Most pathogens were inactivated within 30 sec, with the exception for AIV, which was inactivated within 5 sec. PPMS effectively eliminated rif-SI on all carriers within 30 sec. Moreover, at both concentrations, PPMS successfully inactivated AIV on all carriers within 30 sec, except on stainless steel at 0.5X. Furthermore, PPMS at both concentrations required 5 and 30 sec, respectively, to inactivate AIV on the rayon sheet. Therefore, due to its demonstrated efficacy against a wide range of pathogens across diverse surfaces, PPMS emerges as a crucial alternative disinfectant significantly enhancing biosecurity on and around chicken farms. found in and around animal farms, slaughterhouses, and hospitals.

This paper presents an extension for principles of Differential Geometry on Surfaces (re-hashed through the budding field of CMS, the Calculus of Moving Surfaces). It analyzes mostly 2D Hypersurfaces with Riemannian Geometry and proposes the construction of a 3D Static Frame combining the Surface Basis Vectors with the Orthogonal Normal Field as a 3D Orthogonal Vector Frame. The paper introduces conventions for manipulating Tensors defined using this 3D Orthogonal Vector Frame as well as Curvature Connections associated with this Vector Frame. It then finally introduces Symbols and Tensors to describe Inner Products and Variance within the 3D Vector Frame and then extends all the above concepts to a surface which is Dynamic utilizing principles from CMS. This formulation has potential to extend identities and concepts from CMS and from Differential Geometry in a compact Tensorial Framework, which agrees with the new Framework proposed by CMS.

Background: Assessing the impact of bone health clinical management in breast cancer (BC) patients receiving adjuvant endocrine therapy and designing a personalized clinical pathway to reduce bone loss, in an Italian research hospital. Methods: The primary endpoint was to assess (through the process improvement organizational method) the clinical pathway that post-surgical BC patients prescribed with endocrine therapy undergo to prevent bone loss. The secondary endpoint was to design a personalized clinical pathway for a prompt implementation of guidelines, to assess and possibly prescribe antiresorptive therapy. Results: During the first year of the new diagnostic therapeutic assistance pathway execution, an 60% increase in Dual-Energy X-ray Absorptiometry evaluations within 30 days and a 39.5% increase in antiresorptive therapy prescription within 90 days (since prescription of endocrine therapy) were shown, thus increasing patients’ compliance. Conclusion: Case managers and bone health specialists in this context can improve patients’ adherence to therapies and bone health, helping physicians to expand their collaboration.

Given the opportunities offered by foreign investment in energy infrastructure mostly by Chinese firms, the Government of Cambodia is giving high priority to developing hydropower resources for reducing energy poverty and powering economic growth. Using a “Political ecology of the Asian drivers” framework, this paper assesses China’s involvement in the development of large dams’ in Cambodia and its impacts on the access of natural resources such as water and energy by dam builders, local communities and the government. This analysis is based on 61 interviews and 10 focus group discussions with affected communities, institutional actors, Chinese dam builders and financiers in relation to the first large Chinese dam built in Cambodia, the Kamchay dam. Based on the results of the analysis this paper makes recommendations on how to improve the planning, implementation and governance of large dams to ensure that the dams’ benefits are shared more equally.

The automation of welding processes requires the use of automated systems and equipment, in many cases industrial robotic systems, to carry out welding processes that previously required human intervention. Automation in the industry offers numerous advantages, such as increased efficiency and productivity, cost reduction, improved product quality, increased flexibility and safety, and greater adaptability of companies to market changes. The field of welding automation is currently undergoing a period of profound changes due to a combination of technological, regulatory, and economic factors worldwide. Nowadays, the most relevant aspect of the welding industry is to meet customer requirements by satisfying their needs. To achieve this, the automation of the welding process through sensors and control algorithms ensures the quality of the parts and prevents errors such as porosity, unfused areas, deformations, excessive heat, etc. This paper proposes an intelligent and adaptive system based on the measurement of welding joints using laser scanning and the subsequent analysis of the obtained point cloud to adapt the welding trajectories.

Large-span post-tensioned (PT) beams play a crucial role in maximizing the benefits of post-tensioning techniques. Bonded and unbonded systems are prevalent, with the latter being more widespread in the United States. While bonded systems are advantageous for creating long spans when multiple tendons are grouped in ducts, limited literature exists on their demolition. In a case study, this paper addresses the unique challenge of demolishing large-span bonded post-tensioned beams due to a building's functional change. Emphasizing insights for engineers, it explores the use of cutting and dismantling methods, considering the presence of prestressed cables. The demolition process is distinctive due to the presence of numerous pre-stressed cables along the beams, necessitating a specialized and cautious cutting approach. This is accomplished through the use of a drilling technique that selectively distresses the tendons, ensuring they are not all affected simultaneously. An intriguing observation discussed in this paper pertains to the occurrence of horizontal cracks accompanied by loud sounds following the drilling process, offering insights from the design perspective of PT systems. The paper details an innovative method for safely demolishing large-span bonded PT beams, using ground-penetrating radar and computer models to navigate structural complexities and ensure nearby structures' safety.

Aiming at the limitations of single-functionality, limited applicability, and complex designs prevalent in current metasurfaces, we propose a terahertz multifunctional and multiband tunable metasurface utilizing a VO2-metal hybrid structure. This metasurface structure comprises a top VO2-metal resonance layer, a middle polyimide dielectric layer, and a gold film reflective layer at the bottom. This metasurface exhibits multifunctionality, operating independently of polarization and incident angle. The varying conductivity states of the VO2 layers, enable the metasurface to achieve various terahertz functionalities, including single-band absorption, broadband THz absorption, and multiband perfect polarization conversion for linear (LP) and circularly polarized (CP) incident waves. Finally, we believe that the functional adaptability of the proposed metasurface expands the repertoire of options available for future terahertz device designs.

Intelligent Transportation Systems (ITS) are emerging field characterized by complex data model, dynamics and strict time requirements. Ensuring cybersecurity in ITS is a complex task on which the safety and efficiency of transportation depends. The imposition of standards for a comprehensive architecture, as well as specific security standards, is one of the key steps in the evolution of ITS. The article examines the general outlines of the ITS architecture and security issues. The main focus of security approaches is: configuration and initialization of the devices during manufacturing at perception layer; anonymous authentication of nodes in VANET at network layer; defense of fog-based structures at support layer and description and standardization of the complex model of data and metadata and defense of systems, based on AI at application layer. The article oversees some conventional methods as network segmentation and cryptography that should be adapted in order to be applied in ITS cybersecurity. The focus is on innovative approaches that have been trying to find their place in ITS security strategies recently. The list of innovative approaches includes blockchain, bloom filter, fog computing, artificial intelligence, game theory, and ontologies. In conclusion, a correspondence is made between the commented methods, the problems they solve and the architectural layers in which they are applied.

Today, transit control systems go beyond simple controllers located at the intersections of our streets, involving large companies in the field, which with the implementation and use of sophisticated equipment encompass endless new and advanced technologies that manage to give control to the massive automotive park, thus ensuring fluidity and road safety. Many of these systems are used in the big world capitals, which is why the model used in Santiago, Chile is a system applied and brought directly by the SIEMENS Company of England (specifically the system used in the City of London). It is capable of transmitting the different control signals in a similar and digital way from the different interconnected devices in and out of the road infrastructure.

The symmetries of a Riemann surface $\Sigma \setminus \{a_i\}$ with $n$ punctures $a_i$ are encoded in its fundamental group $\pi_1(\Sigma)$. Further structure may be described through representations (homomorphisms) of $\pi_1$ over a Lie group $G$ as globalized by the character variety $\mathcal{C}=\mbox{Hom} (\pi_1,G)/G$. Guided by our previous work in the context of topological quantum computing (TQC) and genetics, we specialize on the $4$-punctured Riemann sphere $\Sigma=S_2^{(4)}$ and the \lq space-time-spin' group $G=SL_2(\mathbb{C})$. In such a situation, $\mathcal{C}$ possesses remarkable properties (i) a representation is described by a $3$-dimensional cubic surface $V_{a,b,c,d}(x,y,z)$ with $3$ variables and $4$ parameters, (ii) the automorphisms of the surface satisfy the dynamical (non linear and transcendental) Painlev\'e VI equation (or $P_{VI}$), (iii) there exists a finite set of $1$ (\mbox{Cayley-Picard})+$3$ (\mbox{continuous platonic})+$45$ (\mbox{icosahedral}) solutions of $P_{VI}$. In this paper we feature on the parametric representation of some solutions of $P_{VI}$, (a) solutions corresponding to algebraic surfaces such as the Klein quartic and (b) icosahedral solutions. Applications to the character variety of finitely generated groups $f_p$ encountered in TQC or DNA/RNA sequences are proposed.

Proteins play a major role in biosensors in which they provide catalytic activity and specificity in molecular recognition. The immobilization process is however far from straightforward as it often affects the protein functionality. An extensive interaction of the protein with the surface or a significant surface crowding can lead to changes in the mobility and conformation of the protein structure. This review will provide an insight of how the analysis of the physico-chemical features of the protein surface features before the immobilization process can help to identify the optimal immobilization approach to preserve the functionality of the protein when on the surface of the biosensor.

In 2020 the world experienced the threat of the COVID-19 epidemic, as seniors and chronic disease patients typically try to reduce their exercise and social activities to avoid increasing the risk of infection, which could lead to increased loneliness and even many diseases. This research combining golf croquet games with AIoT companion robots constructs a home-based intelligent exercise system thus uses the Technology Acceptance Model (TAM), deduces users’ intention to use this system based on perceived usefulness and perceived ease of use, and adds the needs of love and belonging, esteem, cognitive, aesthetic, and self-actualization in Maslow’s needs theory to conduct system needs analysis. The analysis results show that participants have a high level of acceptance of this system, believing that it is easy to learn and operate, can increase interaction with others, also found that this system can improve self-confirmation, satisfying the third for knowledge, feeling happy, and self-actualization needs are easier to fulfill. In the future, we shall collect and record the seniors in the process of use, so as to find out their health problems as soon as possible, expand their daily life through this exercise, and achieve the goal of happy living and health care.

Fractional flow reserve (FFR) is well recognized as a gold standard measure for the estimation of functional coronary stenosis. Technological progressions in image processing have empowered the reconstruction of three-dimensional models of the coronary arteries via both non-invasive imaging modalities, such as Coronary Computed Tomography Angiography (CCTA), and invasive coronary angiography or intravascular imaging. The application of computational fluid dynamics (CFD) techniques to coronary 3D anatomical models allows the virtual evaluation of the hemodynamic significance of a coronary lesion with high diagnostic accuracy in comparison to the invasive FFR using pressure wires. These opportunities providing hemodynamic information based on anatomy have given rise to a new era of functional angiography and coronary imaging. However, further validations are needed to overcome several scientific and computational challenges before these methods are applied in everyday clinical practice. This review aims to present all the data on the studies and methodologies that have been presented for the virtual estimation of FFR, and the diagnostic execution of the virtual tools for the hemodynamic assessment of coronary lesions compared to the invasive FFR.

The comprehensibility of good predictive models learned from high-dimensional gene expression data is attractive because it can lead to biomarker discovery. Several good classifiers provide comparable predictive performance but differ in their abilities to summarize the observed data. We extend a Bayesian Rule Learning (BRL-GSS) algorithm, previously shown to be a significantly better predictor than other classical approaches in this domain. It searches a space of Bayesian networks using a decision tree representation of its parameters with global constraints, and infers a set of IF-THEN rules. The number of parameters and therefore the number of rules are combinatorial to the number of predictor variables in the model. We relax these global constraints to a more generalizable local structure (BRL-LSS). BRL-LSS entails more parsimonious set of rules because it does not have to generate all combinatorial rules. The search space of local structures is much richer than the space of global structures. We design the BRL-LSS with the same worst-case time-complexity as BRL-GSS while exploring a richer and more complex model space. We measure predictive performance using Area Under the ROC curve (AUC) and Accuracy. We measure model parsimony performance by noting the average number of rules and variables needed to describe the observed data. We evaluate the predictive and parsimony performance of BRL-GSS, BRL-LSS and the state-of-the-art C4.5 decision tree algorithm, across 10-fold cross-validation using ten microarray gene-expression diagnostic datasets. In these experiments, we observe that BRL-LSS is similar to BRL-GSS in terms of predictive performance, while generating a much more parsimonious set of rules to explain the same observed data. BRL-LSS also needs fewer variables than C4.5 to explain the data with similar predictive performance. We also conduct a feasibility study to demonstrate the general applicability of our BRL methods on the newer RNA sequencing gene-expression data.

This research focuses on the development of a foot-worn device to assist individuals with limited mobility in walking. The device aims to reduce the risk of accidents by closely moni-toring the wearer's movements and detecting potential hazards. It incorporates sensors, in-cluding the MPU6050 gyro sensor and KY-031 vibration sensor, to track the wearer's walking behavior. In case of abnormalities, such as falls, the device triggers an auditory alert and noti-fies the caregiver via LINE Notify. The system is controlled by the Node MCU ESP8266, enabling seamless integration with the Internet of Things (IoT). The objective of this study is to design an IoT system for medical assistance. The researchers created a prototype of a smart ankle device capable of detecting falls and sending notifications to the user's smartphone. The effectiveness of the notification system was evaluated using the Line Notify application. Re-sults demonstrated a successful detection of falls in 48 out of 50 trials, with two instances of false alarms during normal walking. The overall efficiency of the smart ankle device was 98%. In summary, the proposed smart ankle device demonstrates promising potential for var-ious applications in fall detection and safety alert systems. Further improvements and collab-orations with healthcare experts are recommended to enhance its performance and make it commercially viable. The device's connectivity and responsiveness to IoT systems are vital aspects to be considered. Future research should aim to develop additional features in collab-oration with physiotherapists and healthcare professionals to meet user requirements. The de-vice holds significant benefits in terms of fall detection and safety alerts, and efforts should be made to enhance its durability, robustness, and commercialization prospects.

The authors developed a wealth curve (bell curve) that can predict a group of individuals’ wealth based on the composite intelligence score which is calculated based on the sum of the intelligence quotient and emotional awareness score. The intelligence quotient was defined as one's ability to perform, comprehend and learn, and emotional awareness was defined as the emotional ability to recognize and make sense of emotions. To move towards the right on the X-axis of the Kabir wealth curve (e.g., accumulate more wealth), individuals must improve emotional awareness and choose a professional career path that lands higher income, calculated risk-taking, and being connected with individuals that can lead to financial deals. Similarly, those facing social injustice can accumulate more wealth by improving emotional awareness, which will help them navigate challenging environments.

This article develops algorithms for the characterization and the visualization of micro-scale features by using a small number of sample points, and with a goal to mitigate for the measurement shortcomings which are often destructive or time consuming. We implement the algorithms to rapidly examine the microscopic features of a Microelectromechanical System (MEMS) surface. Such images are highly dense; therefore, traditional image processing techniques might be computationally expensive. The contribution of this research include first, we develop local and global algorithm based on modified Thin Plate Spline (TPS) model to reconstruct high resolution images of the micro-surface’s topography, and its derivatives by using low resolution images. Second, we obtain a bending energy algorithm from our modified TPS model, and use it to filter out image defects. Finally, we develop a computationally efficient Windowing technique, which combines TPS and Linear Sequential Estimation (LSE), to enhance the visualization of images. The Windowing technique allows rapid image reconstruction based on the reduction of inverse problem.

Currently, the majority of industrial metal processing involves the use of taps for cutting. However, existing tap machines require relocation to specialized inspection stations and only assess the con-dition of the cutting edges for defects. They do not evaluate the quality of the cutting angles and the amount of removed material. Machine vision, a key component of smart manufacturing, is com-monly used for visual inspection. Taps are employed for processing various materials. Traditional tap replacement relies on the technician's accumulated empirical experience to determine the ser-vice life of the tap. Typically, inspecting tooth wear involves removing the tap and evaluating the degree of wear to determine if regrinding or replacement is necessary. Therefore, we propose the use of visual inspection of the tap's external features to determine whether replacement or regrinding is needed. We examined the bearing surface of the tap and utilized single images to identify the cutting angle, clearance angle, and cone angles. By inspecting the side of the tap, we calculated the wear of each cusp. We further investigated whether the cutting portion affected the length of the tool by measuring changes in tooth surface area and the amount of removed thread. This inspection process can facilitate the development of a tap life system, allowing for the estimation of the durability and wear of taps and nuts made of different materials. Statistical analysis can be employed to predict the lifespan of taps in production lines.

With the popularization of intelligent sensing and the improvement of modern medical technology, intelligent medical sensing technology has emerged as the times require. This technology combines basic disciplines such as physics, mathematics, and materials with modern technologies such as semiconductors, integrated circuits, and artificial intelligence, and has become one of the most promising focuses in the medical field. The core of intelligent medical sensor technology is to make existing medical sensors intelligent, portable, and wearable with full consideration of ergonomics and sensor power consumption issues, for conforming to the current trends in cloud medicine, personalized medicine, and health monitoring. With the development of automation and intelligence in measurement and control systems, it is required that sensors have high accuracy, reliability, stability, as well as certain data processing capabilities, self-checking, self-calibration, and self-compensation，while traditional medical sensors cannot meet such requirements. In addition, in order to manufacture high-performance sensors, it is also difficult to improve the material process alone, and it is necessary to combine computer technology with sensor technology to make up for its performance shortcomings. Intelligent medical sensing technology combines medical sensors with microprocessors to produce powerful intelligent medical sensors. On the basis of the original sensor functions, intelligent medical sensors also have functions such as self-compensation, self-calibration, self-diagnosis, numerical processing, two-way communication, information storage, and digital output. This review focuses on the application of intelligent medical sensing technology in biomedical sensing detection from three aspects: physical sensor, chemical sensor, and biosensor.

Tuberculosis (TB) disease still remain a major global threat due to the growing number of drug-resistant species and global warming. Despite the fact that there are new molecular diagnostic approaches, however, majority of developing countries and remote clinics depends on conventional approaches such as Tuberculin test, microscopic examinations and radiographic imaging (Chest X-ray). These techniques are hindered by several challenges which can lead to miss-diagnosis especially when interpreting large number of sample cases. Thus, in order to reduce workload and prevent miss-diagnosis, scientists incorporated computer-aided technology for detection of medical images known as Computer aided Detection (CADe) or Diagnosis (CADx). The use of AI-powered techniques has shown to improve accuracy, sensitivity, specificity. In this review, we discussed about the epidemiology, pathology, diagnosis and treatment of tuberculosis. The review also provides background information on Artificial Intelligence (AI), Machine Learning (ML), Deep Learning (DL), Transfer Learning (TL) and their applications in detection of tuberculosis from both microscopic slide images and X-ray images. The review also proposed an IoT/AI powered system which allows transfer of results obtained from DL models with end users through internet networks. The concept of futuristic diagnosis, limitations of current techniques and open research issues are also discussed.

With the development of big data analysis, blockchain and other technologies, the supply chain of enterprises is transforming to lean and intelligent. As an important link in the enterprise supply chain, the intelligent transformation of procurement plays an important role in the improvement of the supply chain efficiency, therefore, the construction of a common method supporting the intelligent upgrade of the enterprise procurement business has become a key concern for enterprise managers. Based on the balanced scorecard theory and the supply chain maturity model, this study combines the actual situation of procurement management in Chinese energy enterprises and constructs a procurement benchmarking system that balances the development direction of the industry and the actual needs of enterprises. Meanwhile, based on the grounded theory, three major themes of the intelligent procurement system (digital business module, procurement synergy mechanism and procurement ecosystem) are extracted to provide a methodological reference for the construction of intelligent procurement systems of energy enterprises. The study concludes with a case study of China National Energy Group Materials Company to demonstrate the application of the intelligent procurement system built in this paper, with a view to providing methodological reference for the intelligent procurement management in energy enterprises.

The explosive emergence of wireless technologies and standards, covering licensed and unlicensed spectrum bands has triggered the appearance of a huge amount of wireless technologies, with many of them coexisting in the same band. Unfortunately, the wireless spectrum is a scarce resource, and the available frequency bands will not scale with the foreseen demand for new capacity. Certain parts of the spectrum, in particular the license-free ISM bands, are overcrowded, while other parts, mostly licensed bands, may be significantly underutilized. As such, there is a need to introduce more advanced techniques to access and share the wireless medium, either to improve the coordination within a given band, or to explore the possibilities of intelligently using unused spectrum in underutilized (licensed) bands. Therefore, in this paper, we present a SDR based framework that can be employed to devise disruptive techniques to optimize the sub-optimal use of radio spectrum that exists today. Additionally, we describe two use cases for the proposed framework.

Wireless Sensor Networks (WSN) is designed to collect information across a large number of limited battery sensor nodes. Therefore, it is important to minimize the energy consumption of each node, which leads to the extension of the network life. Our goal is to design an intelligent WSN that collects as much information as possible to process it intelligently. To achieve this goal, an agent has been migrated to each node in order to process the information and to cooperate with these neighboring nodes while Mobile Agents (MA) can be used to reduce information between nodes and send those to the base station (Sink). This work proposes to use communication architecture for wireless sensor networks based on the Multi Agent System (MAS) to ensure optimal information collection. The collaboration of these agents generates a simple message that summarizes the important information in order to transmit it by a mobile agent. To reduce the size of the MA, the nodes of the network have been grouped into sector. As for each MA, we have established an optimal itinerary, consuming a minimum amount of energy with the data aggregation efficiency in a minimum time. Successive simulations in large scale wireless sensor networks through the SINALGO simulator show the performance of our proposal, in terms of energy consumption and package delivery rate.

There is a need to find methods to intensify the anaerobic digestion process. One possibility is the use of pre-treatment techniques. Many laboratory tests confirm their effectiveness, but in most cases, there is no verification work carried out on industrial plants. The aim of the research carried out under laboratory conditions and on a large scale was to determine the technological and energy efficiency of the use of hydrodynamic cavitation in the pre-treatment of a waste mixture from dairy farms. It has been shown that hydrodynamic cavitation significantly increases the concentration of organic compounds in the dissolved phase. In the most effective variants, the increase in the content of these indicators was over 90% for both COD and TOC. The degree of solubilisation achieved was 49±2.6% for COD and almost 52±4.4% for TOC. Under laboratory conditions, the highest effects of anaerobic digestion were achieved after 10 minutes of pre-treatment. The amount of biogas was on average 367±18 mL/gCOD and the amount of methane 233±13 mL/gCOD. Further large-scale optimisation trials showed that after 8 minutes of hydrodynamic cavitation, the biogas yield was 327±8 L/kgCOD with a CH4 content of 62.9±1.9%. With this variant, the net energy yield was 66.4±2.6 kWh/day, a value that was 13.9% higher than the original variant with 10 minutes of disintegration and 3.1% higher than the variant without pre-treatment.

A time-sequential working, spatially multiplexed autostereoscopic 3D display design consisting of a fast switchable RGB-color filter array is presented. The wavelength-selective filter barrier emits the light from a display over a larger active area than common autostereoscopic barrier displays. An optical modelling of wavelength-selective barriers has been used for instance to calculate the light ray distribution properties of that arrangement. To find well working display designs, automated searches by simulation and computational evaluation has been proceeded. Wavelength-selective filter barrier arrangements exhibit characteristics different from common barrier displays with similar barrier pitch and ascent. In particular, these constructions show strong angular luminance dependency under barrier inclination specified by correspondent slant angle. In time-sequential implementation it is important to avoid that quick eye or eyelid movement lead to visible color artifacts. In the millisecond regime tunable liquid crystal Fabry-Pérot color filters for the colors red, green and blue are presented. They consist of a sub-micrometer thick nematic layer sandwiched between dielectric mirrors and ITO-electrodes. These cells shall switch narrow-banding light of red, green or blue. An array for a glasses-free 3D display has to be equipped with several thousand switchable filter elements having different color apertures. The newly introduced design is usable as a multi user display as well as a single user system with user adaptive control.

We compare photoaligning properties of polymer layers fabricated from the same constituents: polymethyl-methacrylate (PMMA) and azo-dye Disperse Red 1 (DR1), either chemically attached to the PMMA main-chain, or physically mixed with it. Photoaligning properties depend on the preparation method drastically. This finding is supported by atomic force microscope (AFM) scans monitoring the light-induced changes at the polymer−air interface, and revealing a photoinduced mass transfer.

The objective of this work is to identify the mechanism of dropwise condensation on a smooth solid surface. We investigate the stable dropwise condensation that occurs at a droplet growth rate of 1 µm/s in diameter on a gold-coated glass surface. Additionally, we present our observations on unstable dropwise condensation, i.e., degradation of dropwise condensation of steam on a gold surface. The Surface Plasmon Resonance Imaging (SPRi) approach used in this study has lateral resolutions of 4-10 µm, thickness resolutions of 0.1-1 nm, and temporal resolutions of 200-10,000 frames per second (FPS). SPRi is used to evaluate the existence and structure of thin films and occurrence of initial nuclei during condensation. Visualization of the onset of stable dropwise condensation suggests droplets form at heterogeneous nucleation sites and that no film greater than a monolayer exists on the surface before the formation of droplets. Observation of the unstable dropwise condensation of steam shows the existence of water films that are several nanometers thick between droplets. This work shows that neither the nucleation theory or film rupture theory can individually explain the physics of dropwise condensation. Therefore, there is a need for a more comprehensive theory that can explain the mechanism of dropwise condensation.

The study aimed to identify different molds that grow on various food surfaces. As a result, we conducted a case study for the detection of mold on food surfaces based on the “you only look once (YOLO) v5” principle. In this context, a dataset of 2050 food images with mold growing on their surfaces was created. The dataset was trained using the pre-trained YOLOv5 algorithm. In comparison to YOLOv3 and YOLOv4, this current YOLOv5 model had better precision, recall, and average precision (AP), which were 98.10%, 100%, and 99.60%, respectively. The YOLOv5 algorithm was used for the first time in this study to detect mold on food surfaces. In conclusion, the proposed model successfully recognizes any kind of mold present on the food surface. Using YOLOv5, we are currently conducting research to identify the specific species of the detected mold.

This study presents an instant preview and analysis system implementation of intelligent stereo cameras (ISCs). A parameter optimization prototype adopted the instant preview and analysis system of the ISCs has been achieved the automatic alignment function, and obtained optimal stereo films with the automatic alignment function by adjusting gap and angle between dual cameras. The instant preview and analysis system of the ISCs with parameter optimization can enhance the quality of stereo films effectively and reduce filmed errors and save retouched cost and time in harsh filmed environment.

XPS and ARXPS characterization of surface layers resulting from the functionalization of polymers such as PVC modified with MPTMS and APTES is challenging due to the signals overlap, deriving both from the substrate and the functionalized layers. In this work, a freshly cleaved, ideally flat gold surface was used as carbon-free model substrate functionalized with MPTMS and subsequently grafted with APTES. Avoiding the overlap of signals from carbon atoms present in the substrate, the signals in the C1s, O1s, Si2p, S2p and N1s high-resolution spectra could be assigned to the MPTMS / APTES functionalized layer only and the curve fitting parameters could be determined. Quantitative analysis was in very good agreement with the expected stoichiometry of the functionalized layer, confirming the adopted curve fitting procedure. In addition, it was found that one molecule of APTES grafted two MPTMS via silane groups. ARXPS allowed determining the thickness of the functionalized layers: MPTMS thickness was found to be 0.5 (0.2) nm, MPTMS + APTES thickness 1.0 (0.2) nm in good agreement with Avogadro model calculations. This approach can be considered a powerful tool for characterising functionalized surfaces of more complex systems by XPS.

The three-dimensional morphology of frictional sub-surfaces holds significant importance for studying tribological issues. However, the uniformity of horizontal datum in 3D scanning is limited for curved surfaces, resulting in the inability to obtain accurate contour characterization parameters from the scanning results. This study aims to address this issue by constructing regular surface equations and normalizing the 3D profiler scanning results. By fitting the data, a "plane" surface representative of the surface features is obtained, and the paper demonstrates this approach on the surface morphology of different worn parts in the frictional area of spherical bearings located in the specific environment of the Three Gorges gate. The results indicate that the obtained "plane" effectively reconstructs the three-dimensional morphology map of the regular surface. Moreover, this reconstructed plane not only clearly illustrates the surface characteristics but also provides the foundation for analyzing the wear mechanism.

It is shown that the representation theory of some finitely presented groups thanks to their $SL_2(\mathbb{C})$ character variety is related to algebraic surfaces. We make use of the Enriques-Kodaira classification of algebraic surfaces and the related topological tools to make such surfaces explicit. We study the connection of $SL_2(\mathbb{C})$ character varieties to topological quantum computing (TQC) as an alternative to the concept of anyons. The Hopf link $H$, whose character variety is a Del Pezzo surface $f_H$ (the trace of the commutator), is the kernel of our view of TQC. Qutrit and two-qubit magic state computing, derived from the trefoil knot in our previous work, may be seen as TQC from the Hopf link. The character variety of some two-generator Bianchi groups as well as that of the fundamental group for the singular fibers $\tilde{E}_6$ and $\tilde{D}_4$ contain $f_H$. A surface birationally equivalent to a $K_3$ surface is another compound of their character varieties.

For a set of closed curved surfaces that resemble a Langmuir monolayer an energy is defined that depends only on the curvature of the surfaces interacting with the dimensions normal to the surfaces, that is, the thickness of these surfaces. The thickness, or depth, of the surfaces originates because of surface-particles with chains, that move freely on the inside of the surfaces at a certain depth. This is a purely geometrical description that does not depend on the introduction of ad hoc constants like the elastic constant. With a statistical mechanical model the equations of state are calculated for a gas of non-connected sphere-like surfaces in a volume. There are two states of which the lower temperature state is depending mostly on the interaction energy and surface properties, and the higher temperature state is depending mostly on sphere kinetic and volume properties. This results in aggregation of the sphere-like surfaces from many small ones to few large ones when lowering temperature and vice versa. The model allows for the calculation of the partition function and, when the emergence of the curvature - depth interaction is described as a phase-transformation, for the application of Noether’s theorem. Because of these properties the model is interesting in its own right apart from being an addition to existing elastic descriptions of surfaces.

Preventing the rebound of black and odorous water bodies is critical for improving the ecological environment of water bodies. This study investigated the effect and mechanism of in-situ improvement of sediment microenvironment by nitrate in tailwater of wastewater treatment plants combined with aerobic denitrifying bacteria under low-DO regulation (TailN+CFM+LDO). On the 60th day of remediation, the dissolved oxygen and oxidation-reduction potential in the overlying water increased to 5.6 mg/L and 300 mV, respectively, the acid volatile sulfide in the sediment decreased by 70.4%, and the organic matter in the sediment was reduced by 62.7%, in which the HFOM was degraded from 105 g/kg to 56 g/kg, and the potential risk of water reverting to black and odorous conditions significantly decreased. Amplicon sequencing analysis revealed that the relative abundance of electroactive bacteria Thiobacillus and Pseudomonas with denitrification capacity was found to be significantly higher in the TailN+CFM+LDO group than in the other remediation groups. Functional prediction of 16S sequencing results indicated that both the quantity and activity of critical microbial enzymes involved in nitrification and denitrification processes could enhance in the TailN+CFM+LDO group. These results improved our understanding of the improvement of the sediment microenvironment and could thus facilitate its application.

Traditional methods for discovery and development of new drugs can be a very time-consuming and expensive process because it includes several stages such as compound identification, pre-clinical and clinical trials before the drug is approved by the US Food and Drug Administration (FDA). Therefore, drug repurposing, namely using currently FDA-approved drugs as therapeutics for other diseases than what they are originally prescribed for, is emerging to be a faster and more cost-effective alternative to current drug discovery methods. In this paper, we have described a three-step in silico protocol for analyzing transcriptomics data using online databases and bioinformatics tools for identifying potentially repurposable drugs. The efficacy of this protocol was evaluated by comparing its predictions with the findings of two case studies of recently reported repurposed drugs: HIV treating drug Zidovudine for the treatment of Dry Age-Related Macular Degeneration and the antidepressant Imipramine for Small-Cell Lung Carcinoma. The proposed protocol successfully identified the published findings, thus demonstrating the efficacy of this method. In addition, it also yielded several novel predictions that have not yet been published, including the finding that Imipramine could potentially treat Severe Acute Respiratory Syndrome (SARS), a disease that currently does not have any treatment or vaccine. Since this in-silico protocol is simple to use and does not require advanced computer skills, we believe any motivated participant with access to these databases and tools would be able to apply it to large datasets to identify other potentially repurposable drugs in the future.

In order to improve contrast and restore color for underwater image captured by camera sensors without suffering from insufficient details and color cast, a fusion algorithm for image enhancement in different color spaces based on contrast limited adaptive histogram equalization (CLAHE) is proposed in this article. The original color image is first converted from RGB color space to two different special color spaces: YIQ and HSI. The color space conversion from RGB to YIQ is a linear transformation, while the RGB to HSI conversion is nonlinear. Then, the algorithm separately operates CLAHE in YIQ and HSI color spaces to obtain two different enhancement images. The luminance component (Y) in the YIQ color space and the intensity component (I) in the HSI color space are enhanced with CLAHE algorithm. The CLAHE has two key parameters: Block Size and Clip Limit, which mainly control the quality of CLAHE enhancement image. After that, the YIQ and HSI enhancement images are respectively converted backward to RGB color. When the three components of red, green, and blue are not coherent in the YIQ-RGB or HSI-RGB images, the three components will have to be harmonized with the CLAHE algorithm in RGB space. Finally, with 4 direction Sobel edge detector in the bounded general logarithm ratio operation, a self-adaptive weight selection nonlinear image enhancement is carried out to fuse YIQ-RGB and HSI-RGB images together to achieve the final fused image. The enhancement fusion algorithm has two key factors: average of Sobel edge detector and fusion coefficient, and these two factors determine the effects of enhancement fusion algorithm. A series of evaluate metrics such as mean, contrast, entropy, colorfulness metric (CM), mean square error (MSE) and peak signal to noise ratio (PSNR) are used to assess the proposed enhancement algorithm. The experiments results showed that the proposed algorithm provides more detail enhancement and higher values of colorfulness restoration as compared to other existing image enhancement algorithms. The proposed algorithm can suppress effectively noise interference, improve the image quality for underwater image availably.

Intelligent Tutoring Systems (ITS) are increasingly popular for online learning. These systems use adaptive algorithms to recommend relevant content based on students' profiles. However, instructors need to periodically assess students' performance to ensure learning outcomes and adjust strategies accordingly. Our objective is to predict students' progress in advance, enabling teachers to make quicker decisions and facilitating the iterative process of adaptive algorithms. For this study, we collected a dataset from ALIN, an online learning platform, consisting of over 5,000 students' learning records and test results. Using this dataset, we conducted experiments employing various machine learning algorithms. The results indicate that learning behavior contributes to improving forecast performance, while students' progress strongly correlates with their previous test results. Additionally, we discovered that students' progress can be indirectly predicted by forecasting their scores. Furthermore, by breaking down overall scores into several distinct components and predicting individual scores for each component, the accuracy of the forecasts can be improved.

Different types of resonators are used to create acoustic metameterials and metasurfaces. Recent studies focused on the use of multiple resonators of dipole, quadrupole, octupole and even hexadecapole types. This paper considers the theory of an acoustic metasurface, which is a flat surface with a periodic arrangement of multiple resonators. The sound field reflected by the metasurface is determined. If the distance between the resonators is less than a half the wavelength of the incident plane wave, the far field can be described by a reflection coefficient that depends on the angle of incidence. This allows to characterize the acoustic properties of the metasurface by a homogenized boundary condition, which is a high order tangential impedance boundary condition. The tangential impedance depending on the multiple order of the resonators is introduced. In addition, we analyze sound absorption properties of these metasurfaces, which are a critical factor in determining their performance. The paper presents a theoretical model that accounts for the multiple orders of resonators and their impact on sound absorption. The maximum absorption coefficient for a diffuse sound field, as well as the optimal value for the homogenized impedance, are calculated for arbitrary multipole orders.

Chemical instability of liquid-repellent surfaces is one of the nontrivial hurdles that hinders their real-world applications. Although much efforts have been made to prepare chemically durable liquid-repellent surfaces, few attentions have been paid to exploit the instability for versatile use. Herein, we propose to create hydrophilic patterns on superhydrophobic surface by taking advantage of its chemical instability induced by acid solution treatment. Superhydrophobic Cu(OH)2 nanoneedles covered Cu plate that shows poor stability towards HCl solution (1.0 M) is taken as an example. Results show that 2.5 min of HCl solution exposure leads to the etching of Cu(OH)2 nanoneedles and partial removal of self-assembled fluoroalkyl silane molecular layer, resulting in the wettability transition from superhydrophobocity to hydrophilicity, and the water contact angle decreases from ~160° to ~30°. Hydrophilic dimples with different diameters are then created on the superhydrophobic surfaces by depositing HCl droplets with different volumes. Afterwards, the hydrophilic dimple patterned superhydrophobic surfaces are used for water droplet manipulations, including controlled transfer, merging and nanoliter droplets deposition. The results thereby verify the feasibility of creating wettability patterns on superhydrophobic surfaces by using their chemical instability towards corrosive solutions, which broadens the fabrication methods and applications of functional liquid-repellent surfaces.

Nanometer-curved surfaces are abundant in biological systems as well as in nano-sized technologies. Properly functionalized polymer-grafted nanoparticles (PGNs) adhere to surfaces with different geometries and curvatures. This work explores some of the energetic and mechanical characteristics of the adhesion of PGNs to surfaces with positive, negative and zero curvatures using Coarse-Grained Molecular Dynamics (CGMD) simulations. Our calculated free energies of binding of the PGN to the curved and flat surfaces as a function of separation distance show that curvature of the surfaces critically impacts the adhesion strength. We find that the flat surface is the most adhesive, and the concave surface is the least adhesive surface. This somewhat counterintuitive finding suggests that while a bare nanoparticle is more likely to adhere to a positively curved surface than a flat surface, grafting polymer chains to the nanoparticle surface inverts this behavior. Moreover, we studied the rheological behavior of PGN upon separation from the flat and curved surfaces under external pulling force. The results presented herein can be exploited in drug delivery and self-assembly applications.

Organic-organic interactions play important roles in the secondary organic aerosol formation, but the interactions are complex and poorly understood. Here we use environmental molecular beam experiments combined with molecular dynamics simulations to investigate the interactions between methanol and nopinone, as atmospheric organic proxies. In the experiments, methanol monomers and clusters are sent to collide with three types of surfaces, i.e., graphite, thin nopinone coating on graphite and multilayer surfaces, at temperatures between 140 K and 230 K. Methanol monomers are efficiently scattered from the graphite surface, whereas the scattering is substantially suppressed from nopinone surfaces. The desorption from the three surfaces is similar, suggesting that all the surfaces have weak or similar influences on the methanol desorption. The molecular dynamics results show that upon collisions the methanol clusters shatter, and the shattered fragments quickly diffuse and recombine to clusters. The desorption involves a series of processes, including detaching from clusters and desorbing as monomers. The experimental results also show that all trapped methanol molecules completely desorb within a short experimental time scale at temperatures of 180 K and above. At lower temperatures, the desorption rate decreases, and a long experimental time scale is used to resolve the desorption, where three desorption components are identified. The fast component is beyond the experimental detection limit. The intermediate component exhibits multi-step desorption character and has an activation energy of E_a = 0.18 ± 0.03 eV, in good agreement with simulation results. The slow desorption component is related to diffusion processes due to the weak temperature dependence.

The accurate calculation of real contact area between rough surfaces is a key issue in tribology. In this paper, based on the geometrical information of total contact area and the number of contact spots with respect to surface separation, a new method is proposed to determine the relation between real contact area and normal load. The contact of rough surfaces is treated as an accumulation of incremental multi-plateaus indentations with varying average contact radius. Comparisons with direct finite element calculations and some other theoretical predictions demonstrate the efficiency of this approach.

Functional ZnO nanostructured surfaces are important in a wide range of applications. Here we report facile fabrication of ZnO surface structures at near room temperature with morphology resembling that of sea urchins, with densely packed, μm-long, tapered nanoneedles radiating from the urchin centre. The ZnO urchin structures were successfully formed on several different substrates with high surface density and coverage, including silicon (Si), glass, polydimethylsiloxane (PDMS), and copper (Cu) sheets, as well as Si seeded with ZnO nanocrystals. Time-resolved SEM revealed growth kinetics of the ZnO nanostructures on Si, capturing the emergence of “infant” urchins at the early growth stage and subsequent progressive increase in the urchin nanoneedle length and density, whilst the spiky nanoneedle morphology was retained throughout the growth. ε-Zn(OH)₂ orthorhombic crystals were also observed alongside the urchins. The crystal structures of the nanostructures at different growth time were confirmed by synchrotron X-ray diffraction measurements. On seeded Si substrates, a two-stage growth mechanism was identified, with a primary growth step of vertically aligned ZnO nanoneedle arrays preceding the secondary growth of the urchins atop the nanoneedle array. The antibacterial, anti-reflective, and wetting functionality of the ZnO urchins—with spiky nanoneedles and at high surface density—on Si substrates was demonstrated. First, bacteria colonisation was found to be suppressed on the surface after 24 h incubation in Gram-negative E. coli culture, in contrast to control substrates (bare Si and Si sputtered with 20 nm ZnO thin film). Secondly, the ZnO urchin surface, exhibiting superhydrophilic property with a water contact angle ~0°, could be rendered superhydrophobic with a simple silanization step, characterised by a water static contact angle θ of 159° ± 1.4° and contact angle hysteresis ∆θ < 7°. The dynamic superhydrophobicity of the surface was demonstrated by bouncing-off of a falling 10 μL water droplet, with a contact time of 15.3 milliseconds (ms), captured using a high-speed camera. Thirdly, it was shown that the presence of dense spiky ZnO nanoneedles and urchins on the seeded Si substrate exhibited a reflectance R < 1% over the wavelength range λ = 200–800 nm. The ZnO urchins with unique morphology via a facile fabrication route at room temperature, readily implementable on different substrates, may be further exploited for multifunctional surfaces and product formulations.

Utilization of wasted heat instead of fuel combustion is effective to reduce primary energy consumption for mitigating global warming problem. Because wasted heat sources are not necessarily located close to areas of heat demand, one of the difficulties is that wasted heat has to be transferred from heat source side to heat demand side, which may require heat transportation over long distance. From this point we proposed and have examined new idea of heat transportation using ammonia-water as the working fluid which system is named Solution Transportation Absorption chiller, in short STA. Our previous studies of STA were mainly the experimental investigation with STA facility which cooling power was 25RT (90kW). As a result, the COP of STA was found almost same value 0.65 with the conventional absorption chiller without depending on the transportation distances. The simulation using AspenHYSYS also examined with same experimental condition. The experimental data showed good agreement with the simulation calculation. In this study, we examined the large-scale cooling power STA on simulation. The examination cooling powers were from 90 kW(25RT) to 3517 kW(1000RT). All cooling power achieved around COP 0.64 including pump power consumptions. In addition, we performed the dynamic simulation. As the results, there was no effect of pipeline size on the cooling capacities and mass flow rates. Furthermore, the stability time of the cooling capacities and mass flow rates were almost same regardless of the pipeline size and cooling capacity. In other words, STA may be achieved the same COP even though having various complex conditions compared with the conventional absorption chiller.

Background: Large-cell neuroendocrine carcinoma presents significant treatment challenges owing to its rarity and limited therapeutic options. The LANCE study was designed to explore the survival benefits of incorporating atezolizumab in chemotherapy for metastatic LCNEC. Methods: In this non-randomized study, patients with metastatic LCNEC were treated with ei-ther standard chemotherapy plus atezolizumab or standard chemotherapy alone. The primary outcomes measured were progression-free survival (PFS) and overall survival (OS), with an ex-ploratory analysis of miR375 in plasma as a potential biomarker. Results: Of the 22 screened patients, 17 met the inclusion criteria and were stratified into the atezolizumab and chemotherapy (n=10) or chemotherapy alone(n=7) groups. After a median follow-up of 23.3 months, the 12-month survival rate for the atezolizumab group was 57.1% (95% CI: 32.6%-100%) and 45.7% at 24 months (95% CI: 22.4%-93.2%). In contrast, the chemotherapy group had a 14.3% survival rate at both 12 and 24 months (95% CI: 2.33%-87.7%). The log-rank test for survival showed a statistically significant difference in the atezolizumab-treated group (chi-squared = 4, df = 1, p = 0.04). A non-significant correlation was found between disease pro-gression and elevated levels of miR375. Conclusions: This pilot study suggests that atezolizumab combined with chemotherapy may be effective in treating metastatic LCNEC. The non-significant correlation between plasma miR375 levels and disease progression suggests its biomarker potential, warranting further validation research.

Intelligent cities or smart cities evolve bottom-up along with the digitisation and the creation of digital entities linked to human activities, physical space, and institutional settings of cities; but also, they progress top-down through smart city strategies and projects designed and implemented by public authorities. Yet, thirty-five years since the first use of the term “smart city” or “intelligent city” in the second half of the 1980s, and more than ten years of intense publications in this field, since 2009, there is still a great deal of fuzziness about the projects that make cities intelligent or smart. There is low awareness about the big differences between large, complex urban projects, such as ‘Zero Energy Districts’ or “Mobility-as-a-Service” and projects for automation of city infrastructures, such as smart city lighting, smart metering or finding a parking place. There is a widespread misconception that city intelligence or smartness, the core attribute of smart cities, can be achieved through automation of the city infrastructure. This paper focuses on projects that make cities intelligent or smart. Our intention is to show the complexity and effort needed to achieve this objective. It is an inquiry on projects and data from a large number of smart cities around the world. We analyse core properties of smart city projects, such as (a) interventions on the physical, social, and digital space of cities, (b) the relation to city sectors and ecosystems, (c) engagement of users and stakeholders in decision-making, and (c) impact through optimisation and innovation of city processes and routines. We discuss also projects we have designed and implemented in the framework of URENIO Research and ITI-CERTH. Our conclusions are two-fold. First, we propose a typology of smart city projects along 3 axes and 9 properties. Second, we argue that success and failure to achieve city smartness are mainly institutional. Most barriers to implementation are organisational, legal, and institutional. This can be explained by the social and institutional inertia of the urban system against new solutions, especially when innovation and radical change of existing routines take place. Change management should be a permanent companion of smart city projects implementation, and the modification of routines should be clearly defined and considered already at the design phase of projects.