A high-performance Lead-free Piezoelectric Energy Harvester (LPEH) based on a Ba0.85Ca0.15Ti0.90Zr0.10O3 + CuO 0.3 wt% (BCTZC0.3) composite was fabricated by sintering at 1450℃. The BCTZC0.3 composite, which has an enhanced high-energy-conversion constant (〖d_33×g〗_33), shows improved piezoelectric power-generation performance when compared with conventional piezoelectric energy harvesters. The BCTZC0.3-based LPEH produces instantaneous maximum power of 8.2 mW and an energy density of 107.9 mW/cm3 in a weak magnetic field of 250 μT. This energy harvester can be used to charge a capacitor and operate a wireless sensor network (WSN) system to provide temperature sensing and radio-frequency (RF) transmission in a 250 μT magnetic field. The proposed LPEH is a promising green-energy device for potentially self-powering WSN systems when applied.

Lead-free ferroelectric perovskite N-methyl-N'-diazabicyclo[2.2.2]octonium)–ammonium triio-dide, MDABCO-NH₄I₃, nanocrystals are embedded in three different polymer fibers fabricated by the electrospinning technique. The nanofibers, which are very flexible and have a high Young modulus, behave as active piezoelectric energy harvesting sources that produce a piezoelectric voltage coefficient up to geff = 3.6 VmN-1 and show a blue intense luminescence band at 325 nm. In this work, the pyroelectric coefficient is reported for the MDABCO-NH₄I₃ perovskite inserted in electrospun fibers. At the ferroelectric-paraelectric phase transition, the embedded nanocrystals display a pyroelectric coefficient as high as 194×10-6 Cm-2k-1, within the same order of magnitude as that reported for the state-of-the-art bulk ferroelectric triglycine sulfate (TGS). The perovskite nanocrystals embedded into the polymer fibers remain stable, and no degradation is caused by oxidation.

Owing to the escalating adoption of IoT systems across various domains, the demand for mobile and wireless power sources has surged. Although conventional batteries typically serve as energy storage components, the current low-power consumption devices necessitate eco-friendly alterna-tives. In this study, we designed, fabricated, and characterized an energy harvesting device that repurposes mechanical vibrations. A three-beam design was employed to harvest energy across a broader range of potential frequencies. Finite element models were simulated to ascertain the first bending moment for both sets of beams. A nanostructured piezoelectric multilayer film made of ZnO was deposited onto an AISI 304 steel substrate, and a photosensitive resin seismic mass was implemented. Low-cost techniques generating minimal environmental waste were leveraged in the fabrication process. The piezoelectric film was deposited using a spray nebulization technique involving recycled materials and cost-effective equipment. Micrographs of the layers unveiled the presence of nanospheres with diameters of 250 nm. Employing a custom-made shaker, output voltages of 1.08 V and 180 mV, and power outputs of 1.849 µW and 16.2 nW were achieved for each set of beams. The electrical characterization was conducted using a custom-made shaker, repurposing materials for this objective.

Perovskite solar cells (PSCs) are vital for their optical and electrical properties, with lead-based PSCs reaching a remarkable efficiency of 26.1%, while tin-based counterparts achieve 18.71%. Due to lead's toxicity, there's a push for alternatives like tin. However, tin-based PSCs suffer from stability issues and high defect density states, necessitating the development of cost-effective, high-performance, and eco-friendly alternatives. In this study, we designed a hetero-junction architecture using MASnI3-based Perovskite, opti-mized with SCAPs-1D. After exhaustive analysis, our device achieved a power conversion efficiency of 24.18%, with enhanced parameters including Voc of 0.09323V, Jsc of 30.8360 mA/cm2, and FF of 84.10%. Recombination rates, particularly Shockley-Read Hall recom-bination, were significantly reduced. Parametric analyses, encompassing absorber layer thickness, band gap, defect density, doping concentration, and operating temperature, in-dicate potential efficiency enhancements. This underscores the viability of Sn-based PSCs as a cost-effective, efficient, and environmentally benevolent alternative to lead-based counterparts, promising advancements in future research and development efforts.

Lead halide perovskite has become a promising candidate for high-performance photodetector (PD) applications due to its attractive optical and electrical properties such as high optical absorption coefficient, high carrier mobility, and long carrier diffusion length. However, the presence of highly toxic lead in these devices has limited their practical applications and even hindered their progress toward commercialization. Therefore, the scientific community has been committed to searching for low-toxic and stable perovskite-type alternative materials. Lead-free double perovskite materials, which are still in the preliminary stage of exploration, have achieved inspiring results in recent years. In this review, we mainly focused on two types of lead-free double perovskite based on different Pb substitution strategies, including A2M(I)M(Ⅲ)X6 and A2M(IV)X6. We reviewed the research progress and prospects of lead-free double perovskite photodetectors in the past three years. And more importantly, from the perspective of optimizing inherent defects in materials and improving device performance, we proposed some feasible pathways and made an encouraging perspective for the future development of lead-free double perovskite photodetectors.

Detection methods have been developed to prevent transmission of zoonotic or xenozoonotic porcine viruses after transplantation of pig organs or cells to the recipient (xenotransplantation). Eleven xenotransplantation-relevant viruses including porcine cytomegalovirus, a porcine roseolovirus (PCMV/PRV), porcine lymphotropic herpesviruses -1, -2, -3 (PLHV-1, 2, 3), porcine parvovirus (PPV), porcine circovirus 2, 3, 4 (PCV2, 3, 4), hepatitis E virus genotype 3 (HEV3), porcine endogenous retrovirus-C (PERV-C) and recombinant PERV-A/C have been selected. In the past, several pig breeds, minipigs and genetically modified pigs generated for xenotransplantation had been analyzed using these methods. Here, spleen, liver and blood samples from 10 German slaughterhouse pigs were screened using both, PCR-based and immunological assays. Five viruses: PCMV/PRV, PLHV-1, PLHV-3 and PERV-C were found in all animals, and PCV3 in one animal. Some animals were latently infected with PCMV/PRV as only virus-specific antibodies were detected. Others were also PCR positive in spleen and/or liver, indicative of an ongoing infection. These results provide important information on the viruses that infect German slaughterhouse pigs and together with results of previous studies revealed that the methods and test strategies efficiently work under field conditions.

The study delves into the Zaalklapspruit valley-bottom wetland in South Africa, a site designed through ecological engineering and currently impacted by acid mine drainage due to an upstream defunct coal mine. The research conducted in 2022, aimed to uncover the dynamics of contaminant dispersal within such a wetland setting, focusing on the origins, routes, and ultimate recipients of various metals and sulfur compounds. Analysis revealed that the bottom sediment is rich in organic material, with pH levels observed between 6.05 and 6.59, and exhibited notably low oxidation-reduction potentials, reaching down to −219.67 mV at sample point S3. Notably, Manganese displayed the highest adsorption rates, whereas Iron was predominantly absorbed by the roots of Typha capensis and the algae Klebsormidium acidophilum. The wetland's macrophyte rhizospheres hosted a rich array of microbiota, including families like Helicobacteraceae and Hydrogenophilaceae, which are crucial in metal and sulfur processing. This investigation sheds light on the intricate biogeochemical processes taking place involving the wetland's sediment, macrophyte root systems, periphyton, and microbial populations, underscoring the potential of ecologically engineered wetlands in the remediation of waters affected by acid mine drainage.

Hybrid organic–inorganic perovskites (HOIPs) are promising materials in several fields related to electronics, offering long carrier-diffusion lengths, high absorption coefficients, tunable band gaps, and long spin lifetimes. Recently, chiral perovskites have attracted a huge interest thanks to the possibility of further widening the applications of HOIPs. Chiral materials, being intrinsically non-centrosymmetric, display several attractive physico-chemical properties, including circular dichroism, circularly polarized photoluminescence, nonlinear optics, ferroelectricity, and spin-related effects. Recent studies have shown that chirality can be transferred from the chiral organic ligands into the inorganic perovskite framework, resulting in materials combining the advantages of both chirality and perovskite superior optoelectronic characteristics. Thus, chiral HOIPs have emerged as promising materials for chiroptoelectronic, spintronic, and ferroelectric applications. Here, we report a summary of the latest advances in the field of chiral HOIPs, with a specific focus on lead-free materials and on the first attempts to understand the correlation between the crystal structure features and the chirality-induced functional properties

CuAl8Fe5Ni4Zn4Sn1 (OF 2238) is a new lead-free copper alloy for plain bearing applications that was first officially presented in a scientific journal in 2020. Soon after its invention, the use of the alloy for connecting rod bushings in heavy duty internal combustion engines was promoted and validated with customers. The aim of this article is to describe the material properties of the new alloy in more detail than previously and explain how the advantageous properties of CuAl8Fe5Ni4Zn4Sn1 are generated. At the beginning of the article, the general development trends in the field of copper alloys for sliding applications are presented. This is followed by a presentation of the latest research results about CuAl8Fe5Ni4Zn4Sn, before concluding with a brief summary and future outlook, emphasizing on the fact that recent trends in copper-based sliding applications show great additional potential for further material developments.

We examine worldwide Property and Casualty and Life and Health insurance companies from 2004 until 2023, implementing panel regression models and mediation analysis to show that insurers raise their reserves when they face increasing costs for their potential environmental damages, ultimately reducing their profitability and underwriting capacity. Our findings extend to the insurance sector the previous evidence on banks, demonstrating that environmental damages could affect profits and solvency of financial intermediaries. These insights are important especially for insurance managers and regulators.

The symmetry properties of an ornament contain information about its civilisation and its interactions with other cultural sources. Two-dimensional periodic ornaments can be strictly classified into a limited set of 17 mathematical symmetry groups, also known as wallpaper groups. The collection of ornaments thus classified for a civilisation is characteristic of the cultural group and serves as a fingerprint to identify that group. If the distribution of wallpaper groups is available for several societies, mathematical methods can be applied to determine similarities and differences between the art practices of these communities. This method allows a systematic approach to the general ornamental practices within a culture and their interactions in the form of similarity of fingerprints. We test the feasibility of the method on examples of medieval Armenians, Byzantium, Seljuks first in Persia and then in Anatolia and among Arabs in the Middle East. For this purpose we present the distribution of the planar ornaments and calculate the Euclidean distances in pairs. We tested to what extend geographical and religious factors could account for the observed similarity of ornamental groups between cultures. The results suggest an intensive interaction between the Seljuk Turks and Arab craftsmen who produced the ornaments. Therefore the cultural interactions are religiously motivated.

The refractive index of a liquid serves as a fundamental parameter reflecting its composition, thereby enabling the determination of component concentrations in various fields such as chemical research, food industry, and environmental monitoring. Traditional methods for refractive index (RI) measurement rely on light deflection angles at interfaces between the liquid and a material of known refractive index. In this paper, the authors present a new differential refractometer for highly sensitive measurement of RI differences between two liquid samples. Using a configuration with two cells equipped with flat parallel plates as measuring elements, the instrument facilitates accurate analysis. Namely, the sensor signals from both the solution and the solvent cuvette are generated simultaneously with one laser pulse, reducing the possible fluctuations of the laser radiation intensity. Our evaluation shows the high sensitivity of RI measurements (< 7 · 106), so this differential refractometer can be proposed not only as a high-sensitivity sensing tool that can be used for mobile detection of nanoparticles in solution samples, but also to determine the level of environmental nano-pollution using water (including rain, snow) samples from various natural as well as industrial sources, thus helping to solve some important environmental problems.

The work carried out first-principles calculations within the framework of density functional theory to study the structural stability of the CsSnI₃ compound and the influence of phase transitions on their electronic and optical properties. Using the GGA and SCAN functionals, the relaxed structures of the CsSnI₃ phases were obtained and their geometric characteristics were assessed. Using the Phonopy code based on VASP, calculations of phonon and thermodynamic properties were performed, and the temperatures of phase transitions of CsSnI₃ were determined. The temperature dependences of the thermodynamic parameters α-, β-, γ- and δ-phases of CsSnI₃ were analyzed. The trends in free energy, entropy, enthalpy, heat of formation energy and heat capacity were justified in terms of the pattern of changes in the total energy of the four phases of CsSnI₃ from VASP calculations. It is shown that at 0 K the non-perovskite structure of the CsSnI₃ compound (δ-CsSnI₃) is the most stable (followed by γ-CsSnI₃), and the tetragonal phase (β) is quite unstable, having the highest energy among the perovskite phases. It was revealed that at temperatures above 450 K the tetragonal phase becomes stable, and when the temperature drops, it transforms into the cubic phase (α-CsSnI₃). The phase transition between the β and γ phase of perovskite occurs in the range of 300-320 K, and at 320 K a black-yellow transformation of CsSnI₃ occurs in which the cubic phase (black perovskite) undergoes a phase transition to a non-perovskite conformation (yellow phase). The presence of temperature phase transitions between two orthorhombic phases of CsSnI₃ at 360 K was discovered, although direct transitions of the α⟷γ and γ⟷δ types have not yet been reported in any experiment, except for γ→δ transitions under the influence of moisture. Based on well-relaxed structures (from the SCAN calculations), the band gap widths for four CsSnI₃ phases were calculated and compared with experimental measurements. Electronic properties and Fermi level shifts as a result of phase transformations of CsSnI₃ were assessed using the HSE06 functional and machine learning prediction. The values of the complex dielectric constant and the refractive index of all phases of the CsSnI₃ were determined.

Herein, we present the design technique of a resonant rectifier for piezoelectric (PE) energy harvesting. We propose two diode equivalents to reduce the voltage drop in the rectifier operation, a minuscule-drop-diode equivalent (MDDE) and a low-drop-diode equivalent (LDDE). The diode equivalents are embedded in resonant rectifier integrated circuits (ICs), which use symmetric bias-flip to reduce the power wasted for charging and discharging the internal capacitance of a PE transducer. The self-startup function is supported by synchronously generating control pulses for the bias-flip from the PE transducer. Two resonant rectifier ICs, using both MDDE and LDDE, are fabricated in a 0.18 μm CMOS process and their performances are characterized under external and self-power conditions. Under the external-power condition, the rectifier using LDDE delivers an output power POUT of 564 μW and a rectifier output voltage VRECT of 3.36 V with a power conversion efficiency (PCE) of 90.1%. Under self-power conditions, the rectifier using MDDE delivers a POUT of 288 μW and a VRECT of 2.4 V with a corresponding PCE of 74.6%. The result shows that the power extraction capability of the proposed rectifier is 5.9 and 3.0 times higher than that of a conventional full-bridge rectifier.

The purpose of this study was to elucidate patterns and mechanisms driving seasonal and inter-annual variations of carbon and nitrogen stable isotopes in the zooplankton crustacean commu-nity of Lake Maggiore (Italy), during the period 2009-2020. Different zooplankton taxa and groups revealed different ranges of d13C signatures, giving an insight into food sources and niche partition. In particular, cyclopoids had a restricted range with most negative d13C‰ values and increase in d13C fractionation with the establishment of water thermal vertical stratification, high-lighting the importance of vertical distribution as key factor for taxa coexistence in a vertically heterogenous environment. d13C of the zooplankton community and of Daphnia were positively related to water temperature (R2=0.58 p <0.0001 and R2=0.68 p <0.0001, respectively) and d13C Daphnia signature to chlorophyll-a (R2=0.32, p < 0.0001). Decomposition of time series data for zooplankton carbon and nitrogen signatures and environmental parameters identified increasing trends in water temperature, chlorophyll-a and water conductivity and decrease in nitrate, that matched changes in carbon isotopic signature trend in some zooplankton taxa (Bosmina, Daphnia and diaptomids). Overall, the observed patterns in zooplankton isotopic signatures were interpreted as integrations of climate warming effects in Lake Maggiore, affecting both food sources availability and environmental conditions.

One-Dimensional Solar Cell Capacitance Simulator (1D-SCAPS) and n-i-p planar configuration have been employed for the simulation of the caesium tin iodide (CsSnI₃)-based perovskite solar cell (PSC) with titanium (IV) oxide (TiO₂) and copper thiocyanate (CuSCN) as the electron and hole transport materials respectively. The results obtained for the initially modeled PSC compared well with similar devices in the literature but marred with high recombination rate. As such, the defect density in the CsSnI₃ absorber was varied from 10¹³ cm^-3 to 10¹⁷ cm^-3 and enriched with SnCl₂ (additive) and Br⁻(dopant) respectively. This strategy ensured a reduced concentration of Sn⁴⁺ vacancy (V_Sn) in the CsSnI₃ absorber with improved carrier lifetime and diffusion length beyond 0.05 ns and 1.1µm by a magnitude of the order of 10³ and 10² respectively for the enriched CsSnI₃ –based PSC. For the optimized PSC, we recorded V_OC=1.289 V, J_SC=32.60 mA.cm^-2, FF=83.56% and PCE=35.12%.

This study presents the design and implementation of a piezoelectric power harvesting device to capture vibrational strength from pipelines to autonomous strength IoT devices. The gadget utilizes key components along with the PPA-1001 piezoelectric sensor, STM32F103C8T6 microcontroller, and LTC-3588 energy harvesting strength delivery. Experimental results verified the gadget's performance in harvesting strength within a specific frequency variety of 10 Hz to 50 Hz, with the foremost overall performance at 30 Hz. The device generated the highest voltage of 3.3V, delivering a strength output of 2.18 mW, which is sufficient to power low-strength electronic gadgets. The device maintained solid performance across a temperature range of 20°C to 35°C, underscoring its robustness in various environmental situations. The findings highlight the capacity of this generation to offer a sustainable power source for far-off pipeline tracking, contributing to stronger protection and operational efficiency.

The continuous expansion of urban areas has significantly increased the coverage of impervious paved surfaces, leading to heightened heat absorption and the formation of urban heat islands (UHIs). This research centres on environmental footprint accounting and management to address the escalating UHI risks in the City of Salisbury, Adelaide, South Australia. To comprehend the extent of land use change over time, the study employs the Normalised Difference Vegetation Index (NDVI) in conjunction with Landsat satellite maps. The satellite maps were also analysed for the historical land surface temperatures, exploring the correlation between land use change and land surface temperatures. This approach allows for exploring the correlation between land use transformations and UHI intensity. The research cross-referenced the satellite data with meteorological station records for verification, which led to identifying possible factors associated with the temperature change in the city. Furthermore, the research extends its scope by analysing aerial photography images of the city, enabling a comprehensive investigation of land cover contribution to UHI effects.

OBJECTIVES: To assess the predictive value of serum trypsin and Trypsinogen Activation Peptide (TAP) for the severity of AP by means of a single center cohort study as well as a systematic review of the current literature. METHODS: The literature search was conducted using Medline (PubMed), EMBASE and the Cochrane Central Register. A total of 142 patients with acute pancreatitis (AP) were included in the cohort study and parameters of the revised Atlanta criteria of 2012 and the APACHE II were assessed. RESULTS: The review showed promising results for the predictive value of serum trypsinogen-2, but conflicting results for serum TAP and trypsin. In the cohort study, patients were observed for 4 days after diagnosis of AP: 9 patients had severe AP, 35 patients had moderate AP and 81 patients had mild AP. The ratio of the geometric mean of severe vs mild AP for trypsin was 0.72 (95% CI: 0.51-1.00), p=0.053 and for TAP 0.74 (95% CI: 0.54-1.01), p=0.055 respectively. CONCLUSION: The cohort study showed an inverse correlation of serum levels of TAP and trypsin with severity of AP. Serum TAP and trypsin have an inferior predictive value of severity of AP compared to the clinical APACHE II score.

Plant cells' ability to withstand abiotic stress is strongly linked to modifications in their mechanical characteristics. Nevertheless, the lack of a workable method for consistently tracking plant cell mechanical properties severely restricts our comprehension of the mechanical alterations in plant cells under stress. With Polyethylene Glycol (PEG6000), we created a drought-like environment, and we used the Double Resonator Piezoelectric Cytometry (DRPC) method to dynamically and non-invasively track changes in the stress (ΔS) created and viscoelasticity (storage modulus G' and loss modulus G") of protoplasts and suspension cells of rice during drought stress. The findings demonstrate that, rice suspension cells and protoplasts react mechanically differently to 5%–15% PEG6000 stress, implying distinct resistance mechanisms. However, neither of them can withstand 25% PEG6000 stress, they respond mechanically similarly to 25% PEG6000 stress. The results of DRPC are further corroborated by the morphological alterations of rice cells and protoplasts observed under an optical microscope. To sum up, the DRPC technique functions as a precise cellular mechanical sensor and offers novel research tools for the evaluation of plant cell adversity and differentiating between the mechanical reactions of cells and protoplasts under abiotic stress.

This work proposes a conceptual design for a process for recovering Polystyrene (PS) using solvents of agro-industrial origin. The literature describes the dilution of Expanded Polyestyrene (EPS) in limonene, followed by its insolubilization with alcohols for recovery. However, there is no information on the solubility limit for the PS + limonene + alcohol system, which is critical for the process design. To determine the solubility limit, we diluted the waste EPS in D-limonene, mixed it with ethanol to form a precipitate, and used a gravimetric method to measure the mass of the compounds. These results allowed for the conceptual design of an EPS recycling process using a chemical process simulator, which includes a separator, a distillation column, and auxiliary equipment such as heaters, coolers, and pumps. An empirical correlation was obtained for the solubility limit, which enabled the design of a process for the treatment of 52 kg/s of PS using 0.75 kg /s of ethanol and 2.4 kg / s of D-limonene once the stationary state had been reached. The distillation column is six-stage, with a reflux ratio of 1.5 and duties of 30 000 kW and -25 847 kW for the condenser and reboiler, respectively.

In order to study the effect of explosion load on the flexural performance of RC beams, two RC beams of the same size were carried out explosion test and bearing capacity test successively. Piezoelectric intelligent aggregate was embedded in the beams in advance to monitor the damage state of the beams, which realized the whole process of damage monitoring of the concrete inside the structure from explosion damage to compression damage.Based on wavelet packet analysis and residual bearing capacity damage evaluation criteria, the beam damage was quantitatively evaluated, and the bending bearing capacity of RC beam after explosion damage was compared and analyzed.The results show that the change of concrete strain gauge signal, the phenomenon of crack development and the increase of internal crack development index indicate that the RC beam is damaged by explosion load.After explosion damage, the damage index of the beam increases and the residual bending capacity decreases, which proves that the piezoelectric intelligent aggregate sensor can effectively monitor the bending capacity change of the component after explosion damage.

This study fabricated piezoelectric fibers of polyvinylidene fluoride (PVDF) with graphene using near-field electrospinning (NFES) technology. A uniform experimental design table U*7 (7^4 ) was applied, considering weight percentage (1-13 wt%), distance between needle and disk collector (2.1-3.9 mm), and applied voltage (14.5-17.5 kV). We optimized the parameters using electrical property measurements and the Kriging response surface method. Adding 13 wt% graphene significantly improved electrical conductivity, increasing from 17.7 μS/cm for pure PVDF to 187.5 μS/cm. The fiber diameter decreased from 21.4 μm in PVDF/1% graphene to 9.1 μm in PVDF/13% graphene. Adding 5 wt% graphene increased the β-phase content by 6.9%, reaching 65.4% compared to pure PVDF fibers. Material characteristics were investigated using scanning electron microscopy (SEM), Fourier-transform infrared spectroscopy (FTIR), X-ray diffraction analysis (XRD), contact angle measurements, and tensile testing. Optimal parameters included 3.47 wt% graphene, yielding 15.82 mV voltage at 5 Hz and 5 N force (2.04 times pure PVDF). Force testing showed a sensitivity (S) of 7.67493 log(mV/N). Fibers were attached to electrodes for piezoelectric sensor applications. Results affirmed enhanced electrical conductivity, piezoelectric performance, and mechanical strength. The optimized piezoelectric sensor could be applied to measure physiological signals, such as attaching it to the throat under different conditions to measure the output voltage. The force-to-voltage conversion facilitated subsequent analysis.

This paper proposes the recycling of plates from spent car batteries by the melt quenching method and the incorporation of NiO or Co3O4 contents in order to improve the electrochemical performance of new materials for applications as electrodes on batteries. The analysis of X - ray diffractograms indicates the gradual decrease of the sulfated crystalline phases, respectively 4PbO•PbSO4 and PbO•PbSO4 phases until their disappearance for higher dopant concentrations. IR data show a decreasing trend in the intensity of the bands assigned to sulfate ions and a conversion of [PbO3] pyramidal units into [PbO4] tetrahedral units by doping with high dopant levels yielding to the formation of the PbO2 crystalline phase. The EPR data indicate three resonance lines centered on the gyromagnetic factor, g ~ 2, 2.2 and 8, which are dependent on the NiO level. The first two resonance lines are assigned to nickel ions in higher oxidation states and the last signal centered at g ~ 8 corresponds to nickel metal nanoparticles. This compositional evolution can be explained by considering a process of drastic reduction of nickel ions in oxidation states superior to metallic nickel. The linewidth and the intensity of resonance lines situated at about g ~ 2, 2.17, 4.22 and 7.8 corresponding to the Co+2 ions from EPR spectra depend very strongly on the Co3O4 concentration. The best reversibility of the cyclic voltammograms was highlighted for the samples with x = 8 mol% NiO and 10 mol% Co3O4, which are recommended as suitable in applications as electrode for renewable batteries.

The paper presents a method to assess the effect of electrolyte additives on the energy capacity of Pb-acid batteries. The method applies to any chemically unreactive additive, including suspensions and gels. The approach is thermodynamically based and it leads to the definition of a region of admissible concentrations –the battery’s admissible range– where the battery can undergo an indefinite number of charge/discharge cycles without suffering permanent damage. An experimental procedure to determine this range is presented. The obtained results provide a way to assess the potential of electrolyte additives to improve the energy capacity of Pb-acid batteries. The same results also provide a means to determine the additive concentration that produces the maximum energy capacity increase of the battery. The paper closes with an example of application of the proposed approach to a practical case.

This article reviews recent innovations in piezoelectric actuators, then indicates the future research targets. In the materials, the piezoelectric performances of relaxor-lead titanate (PZN-PT, PMN-PT) single crystals have been improved significantly by an AC electric poling technique. Also new loss characterization techniques facilitate developing high-power density piezoelectrics. The RMS vibration velocity reaches 0.6 m/s in the k₃₁ mode in lead zirconate titanate (PZT) nowadays, which corresponds to power density 30 W/cm³. Pb-free materials are urged due to the recent political regulation on toxic materials. In device designs, the original multilayer actuators (MLA) with Ag/Pd electrode have been switched to the ones with Cu or pure Ag, in order to suppress the heat generation, then to enhance the device power density. Piezoelectric micro-electro-mechanical-systems (MEMS’s) started to utilize the <1 0 0> oriented epitaxial films of rhombohedral PZT compositions, which exhibits enhanced piezoelectric properties. Also for higher-power applications, aero-sol deposition (AD) methods have been introduced to 10 -thick films. Regarding drive/control techniques in piezo-actuators, three developments are on-going, that is, “negative capacitance” power supplies for driving off-resonance (pseudo-DC) piezo-actuators, capacitive AC power supplies for efficiently driving resonance piezo-actuators, and DC/DC converters for harvesting electric energy from high-impedance piezoelectric devices under noise vibration. The applications of piezoelectric actuators in the 21^st century seem to be oriented toward “politico-engineering” with four keywords, “cooperation, protection, reduction, and continuation”. The sustainability technologies include the following piezoelectric items: (a) Pb-free piezoelectrics, (b) ultrasonic technology for decomposing hazardous materials, (c) reduction of contamination gas, (d) piezoelectric energy harvesting, and (e) device improvement with high energy-efficiency. On the other hand, the following crisis technologies have been developed with piezoelectrics: (a) detection and neutralization technologies of infectious/epidemic diseases such as anthrax, (b) autonomous unmanned underwater, aerial, and land vehicles with piezoelectric actuators, (c) pin-point target weapons, (d) high voltage supplies with piezoelectric transformers, and (e) compact energy sources for remote actuating/sensing systems.

This work presents the study of a reproducible acoustic emission method based on the launching of a metallic sphere and low-cost piezoelectric diaphragm. For this purpose, tests were first conducted on a carbon fiber-reinforced polymer structure, and then on an aluminum structure for comparative analysis. The Pencil Lead Break (PLB) tests were also conducted for comparisons with the proposed method. Different launching heights and elastic deformations of the structures were investigated. The results show higher repeatability for the sphere impact method, as the PLB is more affected by human inaccuracy, and it was also effective in damage detection.

The ceramic sherds from approximately 20 samples of lead-glazed tableware, recovered from diverse archaeological sites, including three repurposed storage pits transformed into dumpsters within the medieval city of Santarém (13th-14th century), underwent a meticulous examination. This investigation utilized techniques such as micro-Raman, ground state diffuse reflectance absorption, and X-ray fluorescence spectroscopies, in addition to X-ray diffraction and stereomicroscopy. A parallel study was conducted on contemporaneous European ceramics (glazed sherds) sourced from archaeological sites dating back to the 13th-15th centuries in Saintonge (France), Ardenne, Zomergem, and Bruges (Belgium), as well as Surrey-Hampshire, Kingston, and Cheam (England). The colour of the ceramic bodies is predominantly white or whitish, with a few exhibiting a vivid red hue. Ceramic sherds with a light paste composition were likely crafted using kaolin clays as raw materials. Analyses of fabric, mineralogical, and elemental composition of the sherds suggest that the majority of Santarém's glazed ceramics were locally or regionally produced, potentially derived from a Pliocene kaolin-rich sand formation. However, this conclusion is not supported by the absence of discovered lead glaze kilns or workshops in Santarém for the late Middle Ages. A distinctive feature from the European workshop ceramics lies in the quartz temper content and fabric.

Small and Medium Enterprises (SMEs) are recognized as the main drivers of economic growth and development in many countries throughout the world. SMEs represent about 90% of the manufacturing sector and contribute about 14% of the total manufacturing contribution to GDP. Despite SMEs’ potential to change Nigeria’s status from a consumer economy to a production economy, policies that will ensure that environmentally- friendly manufacturing processes and production technology are not implemented or complied with. SMEs’ operational activities may be deleterious to human health and the ecosystem if environmental management practices are not adopted or prioritized. This paper evaluated the perception and adoption of the Environmental Management System, mainly ISO 14001, by SMEs in Nigeria. One hundred and fifty (150) SMEs in the manufacturing sector in Lagos and Ogun State, Southwestern Nigeria, were randomly selected for this study. The paper posits that environmental management literacy and advocacy should be carried out in SMEs. Environmental management practices involve engaging both industries and product end-users in sustainable practices. The paper concludes that the implementation of environmental management practices and culture by SMEs will abate environmental pollution and its concomitant health risks to humans, the environment, flora, and fauna. Mandatory and voluntary environmental measures are suggested as a means of engendering eco-friendly innovation for sustainable development, triggering employment, job security, and gross domestic product.

Lean practice is recognised for having a great potential in promoting safety risk management in offsite construction (OSC). This paper presents results of a study conducted to assess the impact of lean practice in safety risk management in OSC in a developing country. A quantitative approach using survey-based questionnaire was adopted. Lean management practices (LMPs) identified from literature review were empirically tested using a sample survey of 103 OSC contractors. The survey responses were subjected to descriptive and inferential statistics. The top ranked LMPs for safety risk management in OSC included two mistake proofing practices, i.e., use of personal protective equipment (PPE) and use of hazard warning equipment; two last planner system (LPS) practices, i.e., involvement of workers in safety planning and providing necessary working equipment and one first run studies (FRS) practice, i.e., critical analysis of work methods. These LMPs are useful in controlling high consequence safety risks in OSC. Based on evidence found in this study, the paper argues that lean practice can bring great value in the safety risk management in OSC in countries where OSC is transitioning.

Lead optimization in drug discovery is a crucial phase where initial hits are refined into compounds with improved pharmacological properties. While traditional methods rely on manual experimentation and modifications, AI-driven techniques have revolutionized this process by leveraging big data and predictive modeling. This review explores how AI-driven approaches accelerate lead optimization, showcasing examples like deep neural networks and reinforcement learning. Integration of multi-omic data and experimental validation further enhances AI-driven strategies. The future lies in refining these AI methods, democratizing tools, and interdisciplinary collaboration to streamline drug discovery and address medical needs efficiently.

This paper presents a study about the integration of Piezoelectric Energy Harvesting Systems (PE-EHS) in building envelopes for powering Fiber Bragg Grating (FBG) sensors, enabling efficient and low-consumption monitoring with the objective to leverage Structural Health Monitoring (SHM). The research includes preliminary tests conducted in a real environment to validate the PE-EHS when fully integrated into the façade, capturing mechanical vibrations generated mainly by wind loads. Based on these activities, the final configuration of PE-EHS is defined to provide a complete system for façade monitoring. This integrated system includes the Piezoelectric Generator (PEG), Supercapacitor (SC), Power Conditioner Circuit (PCC), Fibre Optic Sensing (FOS) Interrogator, and the IoT Gateway trans-mitting measurement data within an Internet of Things (IoT) monitoring platform. This configuration is tailored to address the challenges related to the structural integrity of building envelopes. Results demonstrate a potential for a stand-alone solution in the façade sector, but, raising issues for certain limitations, requiring further investigation. In particular, the study emphasizes constraints related to the energy production of PE-EHS for façade integration. It highlights the necessity to carefully consider these limitations within the broader context of their applicability, providing insights for the informed deployment of Piezoelectric Energy Harvesting technology in building envelope monitoring.

This paper presents experimental identification and vibration suppression of a flexible manipulator with non-collocated piezoelectric actuators and strain sensors using optimal multi-poles placement control. To precisely identify the system model, a reduced order transfer function with relocated zeros is proposed, and a first-order inertia element is added to the model to compensate the non-collocation. Comparisons show the identified model match closely with the experimental results both in the time and frequency domains, and a fit of 97.2% is achieved. Based on the identified model, a full-state multi-poles placement controller is designed, and the optimal locations of the closed loop poles are determined. The feasibility of the proposed controller is validated by simulations. Moreover, the controller is tested for different locations of the closed loop poles, and an excellent performance of the optimal locations of the closed loop poles is shown. Finally, the effectiveness of the proposed controller is demonstrated by experiments. Results show that the vibrations of the expected modes are significantly diminished. Besides, vibrations of the higher modes are also slightly suppressed. Accordingly, multi-mode vibrations of the manipulator are well attenuated, and the tip displacement converges quickly with the proposed method.

Background: Gluten and casein-containing foods could aggravate the symptoms of children and adolescents with autism spectrum disorder (ASD), and subsequently impact their quality of life. However, there is a mixed opinion among researchers concerning the impact of alternative diet on reducing ASD symptoms. Objective: This scoping review aimed at examining the impact of the ‘’gluten-free, casein-free’’ (GFCF) diet on health outcomes and the quality of life among autistic children and adolescents. Methods: A scoping review of the literature was performed following the Joanna Briggs Institute (JBI) guidelines. Four databases including EbscoHost, Medline, CINAHL and ProQuest were used to obtain subject-specific studies relevant to the research question and published between July 2013 and March 2024. A comprehensive search using keywords such as “autism spectrum disorder”, “gluten-free diet”, and “casein-free diet” was conducted to obtain articles related to the research focus area. Only full-text, peer-reviewed, written in English articles were selected. Data extraction and data analysis were performed according to the Preferred Reporting Items for Systematic Reviews and Meta-Analyses- extension to Scoping Review (PRISMA-ScR) protocol. Results: From the initial 586 studies a total of 27 articles were included in the final analysis of the review. The thematic analysis included ‘GFCF diet and improvement of the core autistic symptoms’’, “the gut-brain link’’, ‘’dietary interventions and autism’’, ‘’possible side effects due to the GCFC diet’’, and ‘’ inconclusive studies and mixed opinions’’. Majority of the studies showed positive effect of the GFCF diet on a variety of autistic symptoms including positive changes in cognitive skills, behaviour, and gastrointestinal symptoms while some showed conflicting evidence. Conclusion: The currently available evidence on the impact of ‘GFCF’’ diet on the quality of life of autistic children and adolescents may warrant potentially effective interventions for alleviating symptoms of autism spectrum disorders. However, this scoping review highlighted the need for more research to provide more reliable evidence on the health outcomes and quality of life of ASD sufferers to guide practice.

Research on the lead halide-based perovskite solar cells have obtained considerable interest in photovoltaic industry owing to their higher efficiency, easy manufacturing, light-weight and low cost. However, these lead halide-based solar cells are not suitable to manufacture commercially because of the toxicity of lead-based materials. In this context, a lead-free perovskite, cesium-bismuth iodide (Cs₃Bi₂I₉) is considered as a potential alternative to the lead halide-based cell due to their non-toxicity and stability, but this perovskite cannot be matched with random hole transport layer (HTL) and electron transport layer (ETL) materials compared to lead halide-based perovskite because of their crystal structure and band gap. Therefore, in this study, performance comparison of different ideal HTL and ETL materials for Cs₃Bi₂I₉ perovskite layer were studied using SCAPS-1D device simulation on the basis of open circuit voltage, short circuit current, power conversion efficiency (PCE) and fill factor (FF) as well as several novel PSC configuration model were designed that can direct for further experimental research for PSC device commercialization. Results from this investigation reveals that the maximum efficiency of 20.96% is obtained for the configuration ITO/WS₂/Cs₃Bi₂I_9­/NiO/Au with optimized parameters such as thickness 400 nm, band gap 2.1eV, absorber layer defect density 10¹² cm^-3, donor density of ETL 10¹⁸ cm^-3 and the acceptor density of HTL 10²⁰ cm^-3.

The objective of this study was to investigate the concentration and spatial distribution patterns of six potentially toxic heavy metal elements (Mn, Zn, Cr, Pb, Cu and Ni) in bus station dusts in the Xifeng district of Gansu province, NW China. The contents were analyzed for Mn, Zn, Cr, Pb, Cu and Ni by using S8 TIGER Brochures wavelength dispersive X-ray fluorescence spectrometry. Geoaccumulation index (Igeo ), enrichment factor (EF), pollution index (PI) and integrated pollution index(IPI) were calculated to evaluate the heavy metal contamination level of bus station dusts. The results indicate that, in comparison with the background values of local soil, bus station dusts in Xifeng have elevated metal concentrations as a whole. The concentrations of heavy metals investigated in this paper are compared with the reported data of other cities. The results show that the arithmetic means of Mn, Zn, Cr, Pb, Cu and Ni are 440.8, 137.9, 60.0, 42.8, 33.5 and 19.8mg kg−1 respectively. The mean values of Igeo reveal the order of Ni<Mn<Cr<Cu<Zn<Pb. The high Igeo and EF for Cu, Zn and Pb in bus station dusts indicate that there is a considerable Cu, Zn and Pb pollution, which mainly originate from traffic and industry activities. The Igeo and EF of Ni, Mn and Cr are low and the assessment results indicate an absence of distinct Ni, Mn and Cr pollution in bus station dusts. The assessment results of PI also support Cu, Zn and Pb in bus station dusts presented middle pollution, and IPI indicates heavy metals of bus station dusts polluted seriously.

Nucleation is a fundamental and general process at the initial stage of first order phase transition. Although various models based on the classical nucleation theory (CNT) have been proposed to explain the energetics and kinetics of nucleation, detailed understanding on nanoscales are still required. Here we focus on homogeneous bubble nucleation, in which evaluation of the size dependence of bubble free energy is the key issue. We propose application of a formula in stochastic thermodynamics, the Jarzynski’s equality, for data analysis of molecular dynamics (MD) simulation to evaluate the free energy of bubble nucleation. As a test case, we performed a series of MD simulations with Lennard-Jones (LJ) fluid system. By applying an external spherical force field to equilibrated LJ liquid, we evaluated the free energy change during bubble growth as the Jarzynski’s ensemble average of required works. A fairly smooth free energy curve was obtained as a function of bubble radius in metastable liquid of mildly negative pressure conditions.

Finding sustainable renewable energy sources for energy conversion and management is still an obscure topic. This paper presents a model-based simulation for an energy conversion system using piezoelectric energy harvester (PEH) technology. A dynamic mathematical model of a PEH device consists of a piezoelectric transducer, a controlled PWM rectifier, and a closed-loop buck boost converter is developed. A piezoelectric transducer converts mechanical vibrations from a wind force into an oscillating train of electrical charges. The sinewave peak-to-peak level relationship describes the changeable values of these charges, which depend on the severity of the wind vibration. The controlled PWM rectifier, in conjunction with a closed-loop buck-boost converter, converts this train of sinewave cycles into DC voltages. The control blocks of the closed-loop buck-boost converter use the perturbation and observation (P&amp;O) algorithm based on maximum power point tracking (MPPT), which adapts the operational voltage of the piezoelectric source to deliver the maximum power to load and improves the PEHS output voltage stability. A simulation program is employed to perform mathematical analysis on various wind vibration scenarios, piezoelectric sources without PWM converters, and piezoelectric vibration sources connected to a closed-loop P&amp;O converter. The crucial results of this paper demonstrate that the proposed dynamic PEHS model effectively feeds low-power electronic loads by directly adjusting the output voltage level to the set voltage, even under different vibration severity levels. As a result, the proposed PEHS dynamic model serves as a guideline for researchers in the development of self-powered sensors, which contributes to understanding sustainable energy alternatives.

In this paper, we present a finite element simulation of an adaptive piezoelectric fluid-membrane lens modeled in COMSOL Multiphysics. The simulation couples the piezoelectric effect with the fluid dynamics to model the interaction between piezoelectric forces and fluid forces. Also, the simulation is extended to model the thermal expansion of the fluid. Finally, we compare the simulation and experimental results of the adaptive lens refractive power at different actuation levels and temperatures.

This paper presents a demonstration of the feasibility of fabricating micro-cantilever harvesters with extended stress distribution and enhanced bandwidth by exploiting an M-shaped two-degrees-of-freedom design. The measured mechanical response of the fabricated device displays the predicted dual resonance peak behavior with the fundamental peak at the intended frequency. This design has the features of high energy conversion efficiency in a miniaturized environment where the available vibrational energy varies in frequency. It makes such a design suitable for future large volume production of integrated self powered sensors nodes for the Internet-of-Things.

Piezoelectric cantilever harvesters have a large power output at their natural frequency, but in some applications the frequency of ambient vibrations is different from the harvester’s frequency and/or ambient vibrations are periodic with some harmonic components. To cope with these operating conditions harvesters with integrated trimming devices (ITDs) are proposed. Some prototypes are developed with the aid of an analytical model and tested with an impulsive method. Results show that a small trimming device can lower the main resonance frequency of a piezoelectric harvester of the same extent as a larger tip mass and moreover generates at high frequency a second resonance peak. A multi-physics numerical FE model is developed for predicting the generated power and for performing stress-strain analysis of harvesters with ITDs. The numerical model is validated on the basis of experimental results. Several configurations of ITDs are conceived and studied. Numerical results show that harvesters with ITDs are able to generate relevant power at two frequencies owing to the particular shape of the modes of vibration. The stress in the harvesters with ITDs is smaller than the stress in the harvester with a tip mass trimmed to the same frequency.

Abstract: High step-up voltage gain nonisolated DC-DC converter have attracted much attention in photovoltaic, fuel cells and other renewable energy system applications. In this paper, by combining input current ripple-free boost cell with coupled-inductor voltage-doubler cell, an input current ripple-free high voltage gain nonisolated converter is proposed. In addition, passive lossless clamp circuit is adopted to recycle the leakage inductor energy and to reduce the voltage spike across the power switch. By utilizing voltage-doubler cell consisting of diode and capacitor, the voltage stress of switch is further reduced and the resonance between the leakage inductor and the stray capacitor of the output diode is eliminated. A low switch-on-resistance low-voltage-rated MOSFET can therefore be employed to reduce the conduction loss and cost. The reverse recovery loss of output diode is reduced, and the efficiency of converter can be improved. Furthermore, the proposed converter can achieve nearly zero input current-ripple and make the design of electromagnetic interference (EMI) filter easy. Steady state analysis and operation mode of the converter is performed. Finally, experimental results are presented to verify the analysis results of the proposed converter.

Underwater Sensor Networks (UWSNs) can enable a broad range of applications such as resource monitoring, disaster prevention, and navigation-assisted. It is especially relevant for sensor nodes location in UWSNs. Global Positioning System (GPS) is not suitable for using in UWSNs because of the underwater propagation problems. Hence some localization algorithms based on the precise time synchronization between sensor nodes have been proposed which are not feasible for UWSNs. In this paper, we propose a localization algorithm called Two-Phase Time Synchronization-Free Localization Algorithm (TP-TSFLA). TP-TSFLA contains two phases, namely, range-based estimation phase and range-free evaluation phase. In the first phase, we address a time synchronization-free localization scheme base on the Particle Swarm Optimization (PSO) algorithm to decrease the localization error. In the second phase, we propose a Circle-based Range-Free Localization Algorithm (CRFLA) to locate the unlocalized sensor nodes which cannot obtain the location information through the first phase. In the second phase, sensor nodes which are localized in the first phase act as the new anchor nodes to help realize localization. Hence in this algorithm, we use a small number of mobile beacons to help achieve location without any other anchor nodes. Besides, to improve the precision of the range-free method, an extension of CRFLA by designing a coordinate adjustment scheme is updated. The simulation results show that TP-TSFLA can achieve a relative high localization ratio without time synchronization.

This paper addresses the input coupling problem for the shape memory alloy (SMA) actuated parallel platform with completely unknown nonlinear dynamics. The problem means that in a parallel platform with multiple SMA actuators acting together, the displacement of one of the actuators will simultaneously affect the remaining actuators to change. Due to the coupling problem and nonlinear characteristics of the SMA actuators, it is not easy to control the platform to achieve bi-directional swing with completely unknown nonlinear dynamics. Therefore, a model-free adaptive sliding mode control method is proposed to improve the control accuracy of the complex motion of the platform, avoiding the complex modeling process of the SMA actuated parallel platform. Based on the model-free adaptive control (MFAC) theory, a multiple input and multiple output (MIMO) dynamic linearized mathematical model of the parallel platform is established using the online input and output data of the system. Then, a sliding mode controller is designed based on the dynamic model. A rigorous theoretical analysis proves that the proposed model-free adaptive sliding mode controller is able to stably control the SMA actuated parallel platform, and its tracking error is uniformly ultimately bounded (UUB). Finally, experiments are conducted on the established SMA actuated parallel platform. The results show that the proposed model-free controller is feasible and effective, and can control the system well to achieve the complex motion of bi-directional swing.

β-Ga2O3 is a well-known semiconductor material for power devices and other applications. Recently, β-Ga2O3 has also been reported as a scintillator material with a light yield of approximately 8400 ph./MeV, scintillation decay time of &lt;1 μs, and density of 6.44 g/cm3. In this study, 2-inch diameter β-Ga2O3 single crystals were prepared by oxide crystal growth using the cold crucible (OCCC) method under various oxygen partial pressures. In the OCCC method, as in the cold crucible method, a high frequency is applied directly to the oxide materials, which are heated and melted, and the melt is held by the outermost solid material itself that is cooled by water using a copper hearth. In the OCCC method, crystal growth is performed while rotating the seed crystal, as in the Czochralski method, to increase the crystal diameter. The optical properties and radiation responses of the crystals grown under various oxygen partial pressures were evaluated.

Oxytetracycline (OTC) serves as a widely employed antibiotic in veterinary treatment and prevention of infections, potentially leaving residues in animal-derived food products, such as milk, that are consumed by humans. Given the detrimental effects of prolonged human exposure, it becomes imperative to develop precise and sensitive methods for monitoring the presence of OTC in food. This work reports on the fabrication of a label-free electrochemical aptasensor for the determination of OTC as a proof-of-concept.

Studies suggest that elevated postnatal blood lead levels (BLLs) are negatively associated with child growth. This study aimed to investigate associations of childhood BLLs at age one-year and growth outcomes at age six-years (n=661) in a cohort of children in Allada, Benin. The growth outcomes studied are weight-for-age Z-score (WAZ), height-for-age Z-score (HAZ) and BMI-for-age Z-score (BMIZ), head circumference (HC), underweight, stunting, and wasting. Multivariable regression models examined associations between blood lead levels, growth outcomes with adjustment for potential confounders. The geometric mean BLLs was 59.3 μg/L and 82% of children had BLLs &gt;35 μg/L at one year. After adjusting for confounding factors, no association was found between BLLs quartiles and HAZ, WAZ, BMIZ, and height and weight growth velocities. However, boys in the highest quartile had 1.02 cm lower HC (95% CI: [-1.81, -0. 24]) as compared to those in the lowest quartile with a dose-response trend across quartiles (Ptrend =0.02). Furthermore, an increased risk of being stunted was observed in children in the highest quartile of exposure compared to the first (OR: 2.43; 95% CI: [1.11 – 5.33]) with a dose-response trend (Ptrend =0.03). Blood lead was found to be associated with an increased risk of childhood stunting and lower head circumference in a resource-limited setting.

Drosophila melanogaster serves as a important research model both for genetic investigations and for the study of metal toxicity, facilitating the elucidation of physiological mechanisms comparable to those of human organisms. In our research, we evaluated the toxicity effect resulting from exposure to various concentrations of lead and copper on the prolificity rates throughout the life cycle (egg-adult) of four genotypes of Drosophila melanogaster: wild-type (control), white, brown, and white-vestigial. During our study, the prolificity rates were examined across three repetitions under the impact of exposure to concentrations of 0.50, 1.00, 2.00, and 4.00 mM of copper (CuSO₄) and lead (Pb(C₂H₃O₂₎₂). Prolificity rates throughout the life cycle exhibited variations as a direct consequence of genetic factors, the concentration of exposure, and the specific type of metal, either copper or lead. The mutant white-vestigial genotype revealed an IC₅₀ concentration for prolificity inhibition at lower doses of 2.00 mM for copper and 4.00 mM for lead, in contrast to the control genotype (wild-type), which exhibited an inhibition concentration rate >IC₅₀ of 4.00 mM only in the case of copper. Our results concluded that the (i) dose influences the prolificity rate in a directly proportional manner, (ii) comparative analyses between copper and lead revealed that copper displayed toxicity across all genotypes within the concentration range of 0.50 mM to 2.00 mM. In contrast, lead exhibited toxicity within the concentration range of 1.00 mM to 4.00 mM, highlighting a (iii) more acute toxicity characteristic in the case of copper. Thus, the results of this research reflect the importance of using Drosophila melanogaster as a genetic model in the comparative study of the interaction between genetic factors and the toxicity of metals, offering significant insights into monitoring their impact and defining the maximum permissible doses on organisms.

Though Bangladesh is often labelled as "climate change ground zero," the Chittagong Hill Tracts (CHT) were never considered a significant climate change hotspot until heavy rainfall and consequent landslides in 2017. This shift in problem narrative seemingly overlooks myriad environmentally unsustainable 'development' initiatives along with (il)legal deforestation. This paper examines climate change trends and impacts on the lives and livelihoods of diverse local groups in CHT. By analysing changing patterns in meteorological data and qualitative information on changes and challenges in everyday life and the livelihoods of local people, we show a shortfall of captured climate data on CHT to make a strong case for climate change. Yet, this study finds that this region is exposed to a substantial threat of land degradation, flash floods, water scarcity, landslides, and other slow and quick onsets due to a combined effect of deforestation, neoliberalised development, and slight changes in temperature and precipitation patterns. This paper calls for proactive measures to address climate change impacts by endorsing sustainable development strategies prioritizing environmental stewardship, social justice, and economic prosperity.

The one-dimensional MoS₂/carbon nanofibers (1D MoS₂/CNFs) are synthesized by electrospinning using exfoliated MoS₂ nanosheets and polyacrylonitrile as raw materials. The exfoliated MoS₂ nanosheets with size of about 150 nm are encapsulated in carbon nanofibers, and the free-standing MoS₂/CNFs can be easily cut into flexible tablet and directly used as binder-free anode for lithium storage. The resultant 1D MoS₂/CNFs exhibit a very high reversible capacity of 700 mAh g^-1 at 100 mA g^-1 after 50 cycles, high rate capacity (450 mAh g^-1 at 1000 mA g^-1 after 200 cycles) and good cycle stability.

The corporate strategic planning of businesses in sub-Saharan Africa (SSA) largely focuses on immediate financial performances with minimal credence to social sustainability. Thus, studies on the linkage between corporate governance and sustainability reporting have focused on developed economies. This study therefore investigated the role of institutional ownership in the impact of board committee characteristics on social sustainability reporting. The study involved strongly balanced panel data with 1,969 observations of 275 publicly listed non-financial firms in SSA within the timeframe of 2012 to 2021. Data was analyzed using STATA 14.1. The hypotheses were tested using the two-step system of the generalized method of moment (GMM) using the Arellano-Bond dynamic panel-data estimation method. The rate of social sustainability reporting was 39.4%. Relatively, Mauritius and South African firms had the most effective board committee characteristics and higher levels of social sustainability reporting. Institutional ownership had no significant effect on social sustainability reporting. Institutional ownership moderated the effect of sustainability committee independence and sustainability committee gender diversity on social sustainability reporting negatively. The paper presents a new perspective on corporate governance and social sustainability literature by examining the effect of institutional ownership on board committee characteristics and social sustainability reporting in SSA.

We demonstrate for the first time efficient mechanical to electrical energy conversion using InGaN/GaN nanowires (NWs). Using an atomic force microscope equipped with a modified Resiscope module, we analyse the piezoelectric energy generation of GaN NWs and demonstrate an important enhancement when integrating in their volume a thick In-rich InGaN insertion. The piezoelectric response of InGaN/GaN NWs can be tuned as a function of the InGaN insertion thickness and position in the NW volume. The energy harvesting is favoured by the presence of a PtSi/GaN Schottky diode which allows to efficiently collect the piezo-charges generated by InGaN/GaN NWs. Average output voltages up to 330 ± 70 mV and a maximum value of 470 mV per NW has been measured for nanostructures integrating 70 nm-thick InGaN insertion capped with a thin GaN top layer. This latter value establishes an increase of about 35% of the piezo-conversion capacity in comparison with binary p-doped GaN NWs. By considering these output signals, we estimate a maximum power density generated by one layer of dense InGaN/GaN-based NW of about 3.3 W/cm². These results settle the new state-of-the-art for piezo-generation from GaN-based NWs and offer a promising perspective for extending the performances of the piezoelectric sources.

Until now, crystalline NiCo2S4 and its composites have demonstrated improve performances in supercapacitor applications, compared to their oxide analogous, due to their relatively higher electrical conductivity, and multifaceted redox reaction. However, amorphous phase materials have recently shown promise in electrochemical energy storage systems. In this work, urea-assisted amorphous NiCo2S4 on nickel foam (referred to as aNCS) with high nitrogen atom% content, was obtained via hydrothermal method. In comparison to the crystalline NiCo2S4 (referred to as cNCS), aNCS exhibited superior electrochemical performance with specific capacitance of ~3506 F g-1 which is higher than cNCS specific capacitance of ~2185 F g-1 at 2 A g-1. Additionally, aNCS in two-electrode asymmetry supercapacitor exhibited specific capacitance and energy density of ~196 F g-1 and 56 Wh kg-1, respectively.

Autonomous navigation in dynamic environments poses a significant challenge in the field of ro-botics with the primary goals of ensuring both smooth and safe movement. This study introduces control strategy based on an Adaptive Neuro-Fuzzy Inference System (ANFIS) to enhance au-tonomous robot navigation in dynamic environments, emphasizing on collision-free path plan-ning. This strategy employs, a path planning technique to develop a trajectory that allows the ro-bot to navigate smoothly while avoiding collisions with both static and dynamic obstacles. The developed control system incorporates four ANFIS controllers: two are tasked with guiding the robot toward its end point, and the other two are activated for obstacle avoidance. The experi-mental setup conducted in CoppeliaSim involves a mobile robot equipped with ultrasonic sensors navigating in an environment with static and dynamic obstacles. Simulation experiments are conducted to demonstrate the model's capability in ensuring collision-free navigation, employing a path planning algorithm to ascertain the shortest route to the target destination. The simulation results highlight the superiority of the ANFIS-based approach over conventional methods, partic-ularly in terms of computational efficiency and navigational smoothness.

Human Activity Recognition (HAR) technology enables continuous behavior monitoring, particularly valuable in healthcare. This study investigates the viability of using an ear-worn motion sensor for classifying daily activities, including lying, sitting/standing, walking, ascending stairs, descending stairs, and running. Fifty healthy participants (between 20 and 47 years old) engaged in these activities while under monitoring. Various machine learning algorithms, ranging from interpretable shallow models to state-of-the-art deep learning approaches designed for HAR, were employed for classification. Results demonstrate the ear sensor's efficacy, with deep learning models achieving 98% accuracy rate of classification. The obtained classification models are agnostic regarding which ear the sensor is worn and robust against moderate variations in sensor orientation (e.g., due to differences in auricle anatomy), meaning no initial calibration of the sensor orientation is required. The study underscores the ear's efficacy as a suitable site for monitoring human daily activity and suggests its potential for combining HAR with in-ear vital signs monitoring. This approach offers a practical method for comprehensive health monitoring by integrating sensors in a single anatomical location. This integration facilitates individualized health assessments, with potential applications in tele-monitoring, personalized health insights, and optimizing athletic training regimes.

Background/Aim: Stool gluten immunogenic peptides (GIP) determination is now considered a valuable tool for detecting dietary lapses in treated celiac disease (CeD) patients. Our study aims to explore the diagnostic performance of a qualitative lateral flow immunoassay point-of-care test (LFIA/PoCT) compared with a qualitative enzyme-linked immunosorbent assay (ELISA) for detection of stool GIP. Methods: The study is a post hoc analysis of stool samples collected in the real-life conditions from a cohort of gluten-free diet-treated CeD patients. Stool GIP was measured in µg/g of stool using an ELISA kit (iVYLISA GIP S®, Biomedal SL). For the qualitative evaluation of stool GIP, a LFIA/PoCT test (GlutenDetect®; Biomedal S.L) was employed, which reported results as positive or negative. The LFIA/PoCT performance was evaluated against ELISA, considered as the gold standard. GIP concentrations

In this paper, we consider a make-to-order supply chain which satisfies demand that is dependent on both price and quoted lead -time. The manufacturer chooses the lead -time and the order quantity, and the retailer sets the revenue shares. The interactions between the manufacturer and the retailer are modelled as a Nash Game, and the existence and uniqueness of pure strategy equilibrium are demonstrated. A mechanism that enables the supply chain to coordinate the decisions of the members is developed. Lastly, we also analyze how the supply chain system parameters impact the optimal supply chain decisions and the supply chain performance.

In the brain, astrocytes regulate shape and functions of the synaptic and vascular compartments through a variety of released factors and membrane-bound proteins. An imbalanced astrocyte activity can therefore have drastic negative impacts on brain development, leading to the onset of severe pathologies. Clinical and pre-clinical studies show alterations in astrocyte cell number, morphology, molecular makeup and astrocyte-dependent processes in different affected brain regions in neurodevelopmental (ND) and neuropsychiatric (NP) disorders. Astrocytes proliferate, differentiate and mature during the critical period of early postnatal brain development, a time window of elevated glia-dependent regulation of a proper balance between synapse formation/elimination, which is pivotal in refining synaptic connectivity. Therefore, any intrinsic and/or extrinsic factors altering these processes during the critical period may result in an aberrant synaptic remodelling and onset of mental disorders. The peculiar bridging position of astrocytes between synaptic and vascular compartments further allows them to “compute” the brain state and consequently secrete factors in the bloodstream, which may serve as diagnostic biomarkers of distinct healthy or disease conditions.Here, we collect recent advancements regarding astrogenesis and astrocyte-mediated regulation of neuronal network remodelling during early postnatal critical periods of brain development, focusing on synapse elimination. We then propose alternative hypotheses for an involvement of aberrancies in these processes in the onset of ND and NP disorders. In light of the well-known differential prevalence of certain brain disorders between males and females, we also discuss putative sex-dependent influences on these neurodevelopmental events.From a translational perspective, understanding age- and sex-dependent astrocyte-specific molecular and functional changes may help to identify biomarkers of distinct cellular (dys)functions in health and disease, favouring the development of diagnostic tools or the selection of tailored treatment options for male/female patients.

Nowadays, the most advanced micromachined microphones on the market are based on a capacitive coupling principle. Capacitive micro-electro-mechanical systems-based (MEMS) microphones resemble their millimetric counterparts, both in function and in performances. The most advanced MEMS microphones reached a competitive level compared to commonly used measuring microphones in most of the key performance parameters except the acoustic overload point (AOP). In an effort to find a solution for measurement of high-level acoustic fields, microphones with piezoelectric coupling principle have been proposed. Such novel microphones exploit the piezoelectric effect of a thin layer of aluminum nitride, which is incorporated in their diaphragm structure. In these microphones fabricated with micromachining technology, no fixed electrode is necessary, in contrast to capacitive microphones. This specificity significantly simplifies both the design and the fabrication and opens the door for a new improvement of the acoustic overload point as well as harsh environmental applications. Several variations of piezoelectric structures together with an idea leading to electrically controlled sensitivity of MEMS piezoelectric microphone are discussed in the paper.

This study describes the synthesis, and characterization of lead-free organic ferroelectric perovskite N-methyl-N’-diazabicyclo[2.2.2]octonium)-ammonium trichloride (MDABCO-NH4Cl3). The electrospinning technique was employed to obtain nanofibers embedded with this perovskite into PVC polymer for hybrid fiber production. The dielectric, piezoelectric and pyroelectric properties of these fibers were carefully examined. From measurements of the dielectric permittivity temperature and frequency dependence, together with the pyroelectric results, a transition from a high temperature paraelectric to a ferroelectric phase that remained down to room temperature, was found to occur at 438 K. A pyroelectric coefficient as high as 290 C K-1 m-2value obtained is within the same order of magnitude as that reported for MDABCO-NH4I3 and the semiorganic ferroelectric triglycine sulfate (TGS). The hybrid nanofibers exhibited good morphological characteristics and demonstrated very good piezoelectric properties. Specifically, a piezoelectric coefficient of 42 pC/N was obtained when a periodical force of 3 N was applied. The performance of these fibers is on par with materials discussed in the existing literature for fabrication of nano energy harvesting generators. Importantly, the perovskite nanocrystals within the fibers not harmed by oxidation, making them a promising environmentally friendly platform for flexible energy harvesting.

One century ago, ferroelectricity and then piezoelectricity were discovered using Rochelle salt crystals. Today, modern societies are invited to switch towards a resilient and circular economy model. In this context, this work proposes a method to manufacture piezoelectric devices made from agro-resources such as tartric acid and polylactide significantly reducing the energy budget without requiring any sophisticated equipement. These piezoelectric devices are manufactured by liquid phase epitaxy grown Rochelle salt (RS) crystals into a 3D printed poly(Lactic acid) (PLA) matrix being the artificial squared meshes which mimic the natural wood anatomy. This composite material can easily be produced in any fablab with renewable materials and at low processsing temperatures, reducing then the total energy consumed. Manufactured biodegradable samples are fully recyclable and have good piezoelectric properties without any pooling step. The measured piezoelectric coefficients of manufactured samples are higher than many piezoelectric polymers such as PVDF-TrFE.

The evaluation of the piezoelectric properties of ferroelectric ceramics generally has a high level of uncertainty, due to incomplete poling, porosity, domain wall clamping and other effects. In addition, the poling process is often difficult and dangerous, due to the risk of breaking or damaging the sample. A method is described for the evaluation of the potential intrinsic piezoelectric response that a ceramic would have after full poling, without poling it. The method relies on the fact that any material undergoes an elastic softening below the ferroelectric transition temperature, whose magnitude can be expressed in terms of the intrinsic piezoelectric and dielectric coefficients of the material. Such a softening is equivalent to an electromechanical coupling, averaged over all the components due to the unpoled state of the sample, and can be deduced from a single temperature scan of an elastic modulus of a ceramic sample, spanning the ferroelectric and paraelectric states. The strengths, limits and possible applications of the method are discussed.

This study presents a comprehensive approach to calculating the free energy of hydration of methane using Molecular Dynamics simulations. We employed the Free Energy Perturbation (FEP) method to determine the Gibbs free energy associated with transferring a methane molecule into water. Simulations were conducted in a cubic simulation box containing one methane molecule and 1000 TIP4P water molecules. The forward and backward routes were both analyzed, providing consistent free energy differences, which validates the robustness of our methodology. The Gibbs free energy profiles demonstrated characteristic energy barriers and stabilization points, indicative of the interaction dynamics in the solvation process. The results demonstrate the robustness of the FEP method implemented in LAMMPS, yielding free energy in close agreement with experimental data and previous computational studies. The calculated free energy differences for methane hydration exhibited deviations of 13% and 8% for the forward and backward routes, respectively, compared to experimental values. These findings underscore the accuracy and efficiency of using LAMMPS for free energy calculations, contributing to the broader understanding of solvation thermodynamics. Additionally, radial distribution functions were analyzed to provide insights into the structural arrangement of water molecules around methane, revealing strong interaction between methane's carbon atom and water molecules.

In this study, a preload monitoring method using impedance signatures obtained from a piezoelectric-based smart interface is presented for bolted girder connections. Firstly, the background theory of the piezoelectric-based smart interface and its implementation into health monitoring of bolted connections are outlined. A simplified electro-mechanical (EM) impedance model of a smart interface-embedded bolted connection system is formulated to interpret mechanistic understanding of EM impedance signatures under the effect of bolt preload. Secondly, finite element modeling of a bolted connection is carried out to show the numerical feasibility of the presented method and to predetermine the sensitive frequency band of impedance signatures. Finally, impedance measurements are conducted on a lab-scaled bolted girder connection to verify the predetermined sensitive frequency range and to assess the bolt preload changes in the test structure.

Surface initiated atom transfer radical polymerization (SI-ATRP) is one of the most versatile technique to modify the surface properties of material. Recent developed metal free SI-ATRP makes such technique more widely applicable. Herein photo-induced metal-free SI-ATRP of methacrylates, such as methyl methacrylate, N-isopropanyl acrylamide, and N,N- dimethylaminoethyl methacrylate, on the surface of SBA-15 was reported to fabricate organic-inorganic hybrid materials. SBA-15 based polymeric composite with adjustable graft ratio was obtained. The structure evolution during the SI-ATRP modification of SBA-15 was monitored and verified by FT-IR, XPS, TGA, BET, and TEM. The obtained polymeric composite showed enhanced adsorption ability for the model compound toluene in aqueous. This procedure provides a low cost, ready availability, and facile modification way to synthesize the polymeric composites without the contamination of metal.

The success of deep learning (DL) in offline brain-computer interfaces (BCIs) has not yet translated into efficient online applications. This is due to three primary challenges. First, most DL solutions are designed for offline decoding, making the transition to online decoding complex and unclear. Second, the use of sliding windows in online decoding increases the computational complexity of DL training. Third, DL models typically require large amounts of training data, which are often scarce in BCI applications. To address these issues and enable real-time decoding, even across different subjects without calibration data, we first introduce a novel approach called real-time adaptive pooling (RAP). RAP modifies the pooling layers of existing offline DL models towards the online decoding requirements. Additionally, it significantly reduces the computational demand during training by jointly decoding consecutive windows. To reduce the amount of training data required, our approach leverages different levels of domain adaptation. We show how different settings enable different adaptation solutions. The results demonstrate that our approach is both powerful and can be calibration-free, providing a robust and practical solution for real-time BCI applications. These findings pave the way for the development of co-adaptive and highly efficient DL-based online BCI systems.

Piezoelectric ultrasonic motors (USMs) are actuators that use ultrasonic frequency piezoelectric vibration generated waves to transform electrical energy into rotary or translating motion. USMs are paid more attention because they offer distinct qualities over traditional magnet-coil-based motors, such as miniaturization, great accuracy, speed, non-magnetic nature, silent operation, straightforward construction, broad temperature operations, and adaptability. This review study focuses on the principle of USMs and their classifications, characterization, fabrication methods, applications, and future challenges. Firstly, the classifications of USMs, especially, standing wave, traveling wave, hybrid mode, multi degree of freedom USMs are summarized, and their respective functioning principles are explained. Secondly, the finite element modelling analysis for design and performance predictions, the conventional and nano/micro fabrication methods, and, the various characterization methods are presented. Thirdly, their advantages, such as high accuracy, small size, and silent operation and their benefits over conventional motors for the different specific applications are examined. In addition, the substantial contributions to a variety of tech-nical fields like surgical robots, industrial, aerospace, and biomedical applications are introduced. Finally, their future prospects and challenges in USMs development, with an emphasis on downsizing, increasing efficiency, and new materials are outlined.

Inexpensive piezoelectric diaphragms can be used as sensors to facilitate both nozzle height setting and build platform leveling in FFF (Fused Filament Fabrication) 3D printers. Tests simulating nozzle contact are conducted to establish the available output and an output of greater than 8 Volts found at 20 ºC, a value which is readily detectable by simple electronic circuits. Tests are also conducted at a temperature of 80 ºC and, despite a reduction of greater than 80% in output voltage, this is still detectable. The reliability of piezoelectric diaphragms is investigated by mechanically stressing samples over 100,000 cycles at both 20 ºC and 80 ºC and little loss of output over the test duration is found. The development of a nozzle contact sensor using a single piezoelectric diaphragm is described.

The research was conducted in the Kırklareli stream, which flows southwest through the city of the same name toward the village of Kavaklı. The aim of the study is to evaluate water analysis results and assess the potential that the European Union drinking water standard for lead can be achieved in the Kırklareli stream by reliance on the low solubility of lead phosphate minerals. The present study used Visual MINTEQ 3.1 for all water chemistry simulations. The European Union drinking water standard for lead, which is 10 μg L⁻¹, is exceeded at least once and as many as three times at seven of the ten sites during the 2018 sampling season. Although the database solubility of hydroxypyromorphite is exceeded in most samples, it appears this may be the result of major ion substitutions in the hydroxypromorphite that forms in the Kırklareli stream which increases the effective solubility of lead in the stream.

: In this paper we present an optimization of the planar manufacturing scheme for stretch-free, shape induced metal interconnects to simplify the fabrication with the aim of maximizing the flexibility in the structure regarding to stress and strain. The Formation of trenches between silicon islands are actively used in the lithographic process to create arc shape structures by spin coating resist into the trenches. The resulting resist form is used as a template for the metal lines, which are structured on top. Because this arc shape is beneficial for the flexibility of these bridges. The trench depth as a key parameter for the stress distribution is investigated by applying numerical simulations. The simulated results show that the increase in penetration depth of the metal bridge into the trench increases the tensile load which is converted into a shear Force Q(x), that usually leads to increased strains the structure can generate. For the fabrication the filling of the trenches with resist is optimized by varying the spin speed. Compared to the theoretical resistance, the current-voltage measurements of the metal bridges show a similar behavior and almost every structural variation is capable of functioning as a flexible electrical interconnect in a complete island-bridge array.

Leveraging the liquid phase immiscibility effect and phase diagram calculations, a sequence of alloy powders with varying Fe content was designed and fabricated utilizing gas atomization method. Microstructural characterizations, employing SEM, EDS, and XRD analyses, revealed the successful formation of incomplete shell on the surfaces of Al-Bi-Fe powders, obviating the need for Sn doping. This study systematically investigated the microstructure, hydrolysis performance, and hydrolysis process of these alloys in deionized water. Notably, Al-10Bi-7Fe exhibited the highest hydrogen production, reaching 961.0 Nml/g, while Al-10Bi-10Fe demonstrated the peak conversion rate at 92.99%. The hydrolysis activation energy of each Al-Bi-Fe alloy powder was calculated using the Arrhenius equation, indicating a reduction in activation energy achieved through Fe doping.

With demand for the long-term continued use of existing building facilities, structural health monitoring and damage detection are attracting interest from society. Sensors of various types have been practically applied in the industry to satisfy this need. Among the sensors, piezoelectric sensors are an extremely promising technology by virtue of their cost advantages and durability. Although they have been used in aerospace and civil engineering, their application for building engineering remains limited. Remarkably, recent catastrophic seismic events have further rein-forced the necessity of rapid damage detection and quick judgment about the safe use of facilities. Faced with these circumstances, this study was conducted to assess the applicability of piezoelectric sensors to evaluate building components. Specifically, this study emphasizes structural damage caused by earthquakes. After first applying to cyclic loading tests to composite beam component specimens and steel frame subassemblies with a folded roof plate, the prospective damage posi-tions were also found using finite element analysis. Crack propagation and buckling locations were predicted adequately. The piezoelectric sensors provided output when the concrete slab showed tensile cracks, or when the folded roof plate experienced local buckling. Furthermore, damage expansion and progression were detected multiple times during loading tests. Results showed that the piezoelectric sensors can detect structural damage of building components, demonstrating their potential for use in inexpensive and stable monitoring systems.

Type-1 Diabetes Mellitus (T1D) onset and development is closely linked with imbalance of gut microbiome, while supplementation with probiotics may result in positive alterations in gut microbiome composition. In the present study, the effect of a dietary intervention including free or immobilized cells of the presumptive probiotic Pediococcus acidilactici ORE5 on Corinthian currants, a food with beneficial impact in the condition of diabetes, was investigated. Male Wistar rats were studied which were divided into 4 groups: healthy animals, which received the free (H_FP) or the immobilized cells (H_IPC), and diabetic animals, which received the free (D_FP) or the immobilized cells (D_IPC), for 4 weeks (109 cfu/day, in all groups). At the end of the dietary intervention, D_IPC group exerted lower concentration of the inflammatory cytokine IL-1b compared to D_FP. Consumption of immobilized on Corinthian currants P. acidilactici ORE5 cells by diabetic animals led to increased loads of fecal lactobacilli and lower levels of Enterobacteriaceae, coliforms, and E. coli, while Actinobacteria phylum, Akkermansia, and Bifidobacterium genera abundances were increased, and fecal lactic acid was elevated. Overall, the results of the present research demonstrated that functional ingredients can ameliorate gut dysbiosis present in T1D and could be used to design dietary patterns aiming at T1D management. However, well-designed clinical trials are necessary, in order to confirm the beneficial effects in humans.

The Huaniushan lead-zinc-silver deposit is a hydrothermal sedimentary exhalative deposit (SEDEX). The mining area has complex geological conditions. The main tectonic structure in the area is the Huaheitan-Shuangfengshan Fault (F3), which controls the distribution of strata and magmatic rocks. Since the discovery of the Huaniushan Lead-zinc-silver polymetallic deposit, there are diverse understandings of the deposit's genesis and mineralization law, making it challenging to meet the geological interpretation requirements of the Huaniushan Lead-zinc-silver polymetallic deposit. Moreover, a single geophysical exploration method utilizes limited rock physical parameters, making it difficult to effectively characterize underground structures. The integrated exploration of multiple geophysical methods can effectively integrate the geophysical characteristics of different rock physical parameters, reducing the multiplicity and uncertainty of geophysical data inverse interpretation. The comprehensive interpretation of three-dimensional inversion based on various geophysical data, the construction of geological-geophysical models based on geological grounds, the establishment of hidden ore exploration and positioning, and the rapid evaluation of geophysical technology systems are the current development trends in mineral exploration. In light of this, this paper conducts research on the three-dimensional inversion interpretation of the heavy magnetoelectric exploration data of the Huaniushan sedimentary exhalative deposit lead-zinc-silver polymetallic deposit in the mining area and constructs a three-dimensional geological-geophysical model of the study area based on the obtained three-dimensional physical structure of the underground three-dimensional density, magnetization intensity, resistivity, and polarizability structure of the study area, in combination with the information of related geology and drilling holes. It comprehensively interprets the favorable mineralization parts in the study area.

The efficient preparation of single-stranded DNA (ssDNA) rings, as a macromolecular construction approach with topological features, has aroused much interest due to their numerous applications in biotechnology and DNA nanotechnology. However, an extra splint is essential for enzymatic circularization, and by-products of multimers are usually present at high concentrations. Here, we proposed a simple and robust strategy of using permuted precursor (linear ssDNA) for circularization by forming an intramolecular dynamic nick using a part of the linear ssDNA substrate itself as the template. After the simulation of the secondary structure for desired circular ssDNA, the linear ssDNA substrate is designed to have its ends on the duplex part (≥5 bp). By using this permuted substrate with 5'-phosphate, the splint-free circularization is simply carried out by T4 DNA ligase. Very interestingly, formation of only several base pairs (2–4) flanking the nick is enough for ligation, although they form only instantaneously under ligation conditions. More significantly, the 5 bp intramolecular duplex part commonly exists in genomes or functional DNA, demonstrating the high generality of our approach. Our findings are helpful for understanding the mechanism of enzymatic DNA ligation from the viewpoint of substrate binding.

This study aimed to evaluate a cantilever beam-type piezoelectric energy harvester operating on train-induced vibrations for powering Wireless Sensor Networks (WSNs) used in railway track monitoring systems. The harvester's behaviors under different conditions are simulated in MATLAB using the analytical model. Natural frequency, maximum deflection, and stress were calculated with greater precision using eigenfrequency and stationary analysis using COMSOL Multiphysics. At a base excitation of 2 g and a resonant frequency of 4.38 Hz, the simulated results showed that the developed energy harvester prototype could generate up to 14 V of AC output voltage and 550 mW of output power. These findings highlight the promising potential of the proposed energy harvester for transforming train mechanical energy into electrical power. This energy harvester's viability and dependability for real-world applications in monitoring railway tracks are supported by developed analytical and simulation models.

This study compares the action of different handpieces (turbine, high-speed electric handpiece and piezoelectric device) on surface roughness of enamel and dentin when using diamond-coated working tips and burs of the same grit size. Experiment was conducted on 15 extracted first molars from patients aged 45 to 60 years. The occlusal portion was removed using a diamond-coated water wheel and then refined with a 120-130 μm grit bur in order to obtain a flat surface with an adequate exposition of the dentin core. Each surface was divided into three portions and every portion was finished with one of the three tested instruments. Rotary burs and piezoelectric tips had the same grit size (60 μm) and load on handpiece during preparation never exceeded 150 g. Surface roughness parameters (Ra, Rsk, Rku) were recorded with an optical profilometer and SEM analysis of treated surfaces and working tips was conducted. Ra and Rsk differed significantly between enamel and dentin only after using turbine (p=0.004 and p=0.007, respectively). No significant differences were observed in Ra, Rsk, and Rku between enamel and dentin when using high-speed electric handpiece or piezoelectric device. Turbine produced higher Ra and Rsk values on dentin than the other devices, while no significant differences were found between piezoelectric handpiece and high-speed electric contra-angle on both substrates. Summarizing, the findings of the present study demonstrated that turbine generated rougher surfaces on dentin compared to the other handpieces. Moreover, the turbine produced more asymmetrical surface profiles on both enamel and dentin. However, it should be considered that these differences in roughness (Ra) were within the range of 0.25-0.30 μm: it is still unclear if these variations, although statistically significant, will influence final clinical outcomes.

The abundant mechanical vibration energy in bridge road environment can be converted into electric energy by using the piezoelectric energy harvest technology, which could be an efficient way to provide energy required by the wireless sensor network in the bridge condition monitoring system. An autonomous energy harvesting system has been designed based on cantilever beams for sensing and acquiring the bridge vibration energy. After the analysis of the dynamic properties of the piezoelectric cantilever beam in the energy conversion, three kinds of interface circuits were compared through simulation and experimental results. It was shown that the VD interface circuit has less power loss. Furthermore, the proposed closed loop control method based on the VD circuit was simple, adaptive, and self-powered, which is suitable for the road energy harvesting application. Finally, the energy harvesting system based on VD circuit was realized with harvested power of around 0.8mW.

In principle, modular or integral character of manufacturing lines depends on topological designs of products and determined operation tasks. On the other hand, in specific situations there is an articulated need for modular design in smart manufacturing systems, since modular layouts are a crucial step towards agile production via smart manufacturing. The aim of this paper is to explore how the modular layout relates to manufacturing lead time (MLT) and to operational complexity of smart manufacturing systems. For this purpose, topologically different models of alternative process layouts were simulated and tested, while MLT values were obtained using Tecnomatix Plant Simulation. Obtained positive findings of this research could be useful not only in selection of the most suitable process design from the alternative ones, but especially in deepening knowledge and better understanding of the concept of optimal network modularity.

The heavy metal lead (Pb) can irreversibly damage the human nervous system. To help understand Pb-induced damage, we applied a genetically encoded Förster resonance energy transfer (FRET)-based Pb biosensor Met-lead 1.44 M1 to two living systems to monitor the concentration of Pb: induced pluripotent stem cell (iPSC)-derived cardiomyocytes as a semi-tissue platform, and Drosophila melanogaster fruit flies as an in vivo animal model. Different FRET imaging modalities were used to obtain FRET signals, which represented the presence of Pb in the tested samples in different spatial dimensions. Using iPSC-derived cardiomyocytes, the relationship between beating activity (20–24 beats per minute, bpm) determined from the fluctuation of fluorescent signals and the concentrations of Pb represented by the FRET emission ratio values of Met-lead 1.44 M1 was revealed from simultaneous measurements. Pb (50 μM) affected the beating activity of cardiomyocytes, whereas two drugs that stop the entry of Pb differentially affected this beating activity: verapamil (2 μM) did not reverse the cessation of beating, whereas 2-APB (50 μM) partially restored this activity (16 bpm). The results clearly demonstrate a potential of this biosensor system as an anti-Pb drug screening application. In the Drosophila model, Pb was detected within the adult brain or larval central nervous system (Cha-gal4>UAS-Met-lead 1.44 M1) using fast epifluorescence and high-resolution two-photon 3D FRET ratio image systems. The tissue-specific expression of Pb biosensors provides an excellent opportunity to explore the possible Pb-specific populations within living organisms. We believe that this integrated Pb biosensor system can be applied to the prevention of Pb poisoning and advanced research on Pb neurotoxicology.

The DEAD-box RNA helicase DDX3X is a multifunctional protein involved in RNA metabolism and stress responses. In this study, we investigated the role of RG/RGG motifs in the dynamic process of liquid-liquid phase separation (LLPS) of DDX3X using cell-free assays and explored their potential link to cancer development through bioinformatic analysis. Our results demonstrate that the number, location, and composition of RG/RGG motifs significantly influence the ability of DDX3X to undergo phase separation and form self-aggregates. Mutational analysis revealed that the spacing between RG/RGG motifs and the number of glycine residues within each motif are critical factors in determining the extent of phase separation. Bioinformatic analysis of cancer genomic datasets uncovered a significant enrichment of DDX3X mutations in RG/RGG motifs across multiple cancer types, particularly in the N-terminal region of the protein. Furthermore, we found that DDX3X is co-expressed with the stress granule protein G3BP1 in several cancer types and can undergo co-phase separation with G3BP1 in a cell-free system, suggesting a potential functional interaction between these proteins in phase-separated structures. DDX3X and G3BP1 may interact through their RG/RGG domains and subsequently exert important cellular functions under stress situation. Collectively, our findings provide novel insights into the role of RG/RGG motifs in modulating DDX3X phase separation and their potential contribution to cancer pathogenesis.

Early detection of neurological conditions is critical for timely diagnosis and treatment. Identifying cellular-level changes is essential for implementing therapeutic interventions prior to symptomatic disease onset. However, monitoring brain tissue directly through biopsies is invasive and high-risk. Bodily fluids such as blood or cerebrospinal fluid contain information in many forms, including proteins and nucleic acids. Particularly, cell-free DNA (cfDNA) has potential as a versatile neurological biomarker. Yet, our knowledge of cfDNA released by brain tissue and how cfDNA changes in response to deleterious events within the brain is incomplete. Mapping changes in cfDNA to specific cellular events is difficult in vivo, where many tissues contribute to circulating cfDNA. Organoids are tractable systems for examining specific changes consistently in a human background. However, few studies have investigated cfDNA released from organoids. Here, we examined cfDNA isolated from cerebral organoids. We found that cerebral organoids release quantities of cfDNA sufficient for downstream analysis with droplet-digital PCR and whole-genome sequencing. Further, gene ontology analysis of genes aligning with sequenced cfDNA fragments revealed association with terms related to neurodevelopment and autism spectrum disorder. We conclude that cerebral organoids hold promise as tools for the discovery of cfDNA biomarkers related to neurodevelopmental and neurological disorders.

In this paper the possibility of harvesting energy from the vibrations of a plate is analyzed. The harvester takes the form of a cantilever dynamic vibration absorber equipped with a piezoelectric layer and tuned by means of a tip mass to the first mode of vibration of the plate. A mathematical model of the coupled system composed of the plate and the harvester is presented. The validity of the proposed harvester is proved by means of simulations carried out with the modal expansions approach. Simulation results highlighting the effect of harvester tuning and location are presented as well. Then the validity of the harvester is confirmed by experimental tests carried out both with a concentrated impulsive load and with a distributed pressure load. Simulations and experimental tests show that the cantilever piezoelectric dynamic vibration absorber generates open circuit voltage an order of magnitude larger than the one generated by the same piezoelectric layer when directly bonded to the plate surface.

Generating localized haptic feedback on touch displays has been a challenge in recent years. In this study, we introduce a haptic interface using transparent thin-film PVDF actuators to address this issue. The transparency feature allows for mounting the actuators at any location beneath the display, enabling localized haptic feedback as the generated vibration is primarily evident on the mounting area. Two different configurations are designed, simulated and prepared to explore the effectiveness of the proposed approach. The first configuration is used to characterize the haptic interface. Modal and forced-vibration analysis are performed to identify important design characteristics based on human factor considerations. Subsequent 2AFC psychophysics experiments validate the characteristics. In the second configuration, eight actuators are attached to the touch surface in a 2x4 matrix formation and excited at different voltage amplitudes. Human experiments are conducted based on the results from corresponding forced-vibration analysis. The results show that subjects demonstrate an accuracy of 96% in identifying locations with haptic feedback when the actuators are excited with 232 Vpp. Overall, our study demonstrates the effectiveness of the haptic interface equipped with PVDF-type actuators in achieving localized haptic feedback on touch displays.

Satellites are subject to various severe vibration during different phases of flight. The concept of satellite smart adapter is proposed in this study to achieve active vibration control of launch vehicle on satellite. The satellite smart adapter has 18 active struts in which the middle section of each strut is made of piezoelectric stack actuator. Comprehensive conceptual design of the satellite smart adapter is presented to indicate the design parameters, requirements and philosophy applied which are based on the reliability and durability criterions to ensure successful functionality of the proposed system. The coupled electromechanical virtual work equation for the piezoelectric stack actuator in each active strut is drived by applying D'Alembert's principle. Modal analysis is performed to characterize the inherent properties of the smart adapter and extraction of a mathematical model of the system. Active vibration control analysis was conducted using fuzzy logic control with triangular membership functions and acceleration feedback. The control results conclude that the proposed satellite smart adapter configuration which benefits from piezoelectric stack actuator as elements of its 18 active struts has high strength and shows excellent robustness and effectiveness in vibration suppression of launch vehicle on satellite.

In the last decades synthetic jet actuators have gained much interest among the flow control techniques due to their short response time, high jet velocity and absence of traditional piping, that matches the requirements of reduced size and low weight. A synthetic jet is generated by the diaphragm oscillation (generally driven by a piezoelectric element) in a relatively small cavity, producing periodic cavity pressure variations associated with cavity volume changes. The pressured air exhausts through an orifice, converting diaphragm electrodynamic energy into jet kinetic energy. This review paper faces the development of various lumped-element models (LEMs) as practical tools to design and manufacture the actuators. LEMs can quickly predict device performances such as the frequency response in terms of diaphragm displacement, cavity pressure and jet velocity, as well as the efficiency of energy conversion of input Joule power into useful kinetic power of air jet. The actuator performance is analyzed also by varying typical geometric parameters such as cavity height and orifice diameter and length, through a suited dimensionless form of the governing equations. A comprehensive and detailed physical modeling aimed to evaluate the device efficiency is introduced, shedding light on the different stages involved in the process. Overall, the influence of the coupling degree of the two oscillators, the diaphragm and the Helmholtz’s one, on the device performance is discussed throughout the paper.

We describe a novel system for online prediction of lead seizures from long-term intracranial electroencephalogram (iEEG) recordings for canines with naturally occurring epilepsy. This study adopts new specification of lead seizures, reflecting strong clustering of seizures in observed data. This clustering results in fewer lead seizures (~7 lead seizures per dog), and hence new challenges for online seizure prediction, that are addressed in the proposed system. In particular, machine learning part of the system is implemented using the Group Learning method suitable for modeling sparse and noisy seizure data. In addition, several modifications for the proposed system are introduced to cope with non-stationarity of noisy iEEG signal. They include: (1) periodic re-training of SVM classifier using most recent training data; (2) removing samples with noisy labels from training data; (3) introducing new adaptive post-processing technique for combining many predictions made for 20-second windows into a single prediction for 4 hr segment. Application of the proposed system requires only 2 lead seizures for training the initial model, and results in high prediction performance for all four dogs (with mean 0.84 sensitivity, 0.27 time-in-warning, and 0.78 false-positive rate per day). Proposed system achieves accurate prediction of lead seizures during long-term test periods, 3–16 lead seizures during 169–364 days test period, whereas earlier studies did not differentiate between lead vs. non-lead seizures and used much shorter test periods (~few days long).

Deflectometry is a key component in the precise measurement of specular (mirrored) surfaces, however traditional methods often lack an end-to-end approach that performs 3D reconstruction in a single shot with high accuracy and generalizes across different free-form surfaces. This paper introduces a novel deep neural network (DNN)-based approach for end-to-end 3D reconstruction of free-form specular surfaces using single-shot deflectometry. Our proposed network, VUDNet, innovatively combines discriminative and generative components to accurately interpret orthogonal fringe patterns and generate high-fidelity 3D surface reconstructions. By leveraging a hybrid architecture integrating a Variational Autoencoder (VAE) and a modified U-Net, VUDNet excels in both depth estimation and detail refinement, achieving superior performance in challenging environments. Extensive data simulation using Blender, leading to a dataset which we are making available, ensures robust training and enables the network to generalize across diverse scenarios. Experimental results demonstrate the strong performance of VUDNet, setting a new standard for 3D surface reconstruction. The implementation of VUDNet is available on GitHub at https://github.com/hadious/VUDNet.

The optimal timing for actively discontinuing immune checkpoint inhibitor therapy in long-term responders with recurrent/metastatic head and neck squamous cell carcinoma (R/M HNSCC) remains unresolved. We conducted a retrospective study of 246 patients with R/M HNSCC treated with nivolumab to determine the optimal timing to actively discontinue nivolumab therapy. We examined the point at which progression-free survival (PFS) plateaued in all cases. We compared the prognosis of 19 (7.7%) ongoing cases and 227 (92.3%) discontinued cases and analyzed treatment duration and treatment-free interval (TFI). The 6-year overall survival was 11.8% (median, 12.1), and the 6-year PFS was 15.3% (median, 3.0). The PFS curve remained stable for 3 years. The median duration of nivolumab treatment was 2.9 months (range, 0.03–81.9): Ongoing group, 41.8 (5.6–81.9); Decision group, 36.8 (4.0–70.1); Toxicity group, 30.6 (2.8–64.8); and progressive disease group, 2.0 (0.03–42.9). TFI in the Decision group was 15.1 months (0.6–61.6) and 30.6 months (2.8–64.8) in the Toxicity group. Limited number of long-term responders in R/M HNSCC cases treated with nivolumab exists. Given that PFS plateaued at 3 years, we propose that the optimal duration of treatment for this subset of patients is 3 years.

The commercial oxygen-free copper sheets were cold-rolled with reduction rates ranging from 20% to 87% reduction rate and annealed at 400, 500 and 600 °C. The microstructure and texture evolution during cold-rolling and annealing processes were studied using optical microscopy (OM), the scanning electron microscopy (SEM) and the electron back-scattered diffraction (EBSD). The results show that the deformation textures of {123} (S) , {112} (Copper) and {110} (Brass) were continuously enhanced with the increase of cold-rolling reduction. The orientations along the α-oriented fiber converged towards Brass and the orientation density of β fiber obviously increased when the rolling reduction exceeded 60%. The recrystallization texture was significantly affected by the cold-rolling reduction. After 60% cold-rolling reduction, Copper and S textures components gradually decreased and {011} recrystallization texture component formed with the increase of annealing temperature. After 87% cold-rolling reduction, a strong Cube texture formed and other textures were inhibited with the increase of annealing temperature. The strong Brass and S deformation texture was conducive to the formation of a strong Cube annealing texture. The density of annealing twin boundary decreased with the increase of annealing temperature, and more annealing twin boundaries formed in the oxygen-free copper sheets with the increase of cold rolling reduction.

In Philadelphia chromosome positive B-cell (Ph+) acute lymphoblastic leukemia (LLA), growing evidence has ac-cumulated about the efficacy of low-intensity and chemo-free regimens. Our objective was to analyze all recent trials evaluating these treatments and to compare them in terms of efficacy. We applied the Shiny method, an artificial intelligence technique, to analyze Kaplan-Meier curves and reconstruct patient-level data. Reconstructed patient data were then evaluated through standard survival statistics and subjected to indirect head-to-head treatment comparisons. The endpoint was progression-free survival (PFS). Based on 848 reconstructed patients, 9 trials were analyzed. The survival data from these trials were pooled into three types of treatments: i) treatments based on ty-rosine kinase inhibitors (TKIs) combined with reduced-intensity chemotherapy (denoted as TKICHE); ii) TKIs as-sociated to steroids with no chemotherapy (TKISTE); iii) chemotherapy-free combinations of blinatumomab plus TKIs (TKIBLI). According to the Shiny method, the three PFS curves were reported in a single Kaplan-Meier graph and subjected to survival statistics. In terms of PFS, TKIBLI ranked first, TKICHE second, and TKISTE third; the differences between these three regimens were statistically significant. This multi-treatment Kaplan-Meier graph, generated through the Shiny method, summarized the current evidence on these treatments in both qualitative and quantitative terms.

: In Philadelphia chromosome positive B-cell (Ph+) acute lymphoblastic leukemia (LLA), growing evidence has accumulated about the efficacy of low-intensity and chemo-free regimens. Our objective was to analyse all recent trials evaluating these treatments and to compare them in terms of efficacy. We applied the Shiny method, an artificial intelligence technique, to analyse Kaplan-Meier curves and reconstruct patient-level data. Reconstructed patient data were then evaluated through standard survival statistics and subjected to indirect head-to-head treatment comparisons. The endpoint was progression-free survival (PFS). Based on 562 reconstructed patients, 8 trials were analyzed. The survival data from these trials were pooled into three types of treatment: i) treatments based on tyrosine kinase inhibitors (TKIs) combined with reduced-intensity chemotherapy (denoted as TKICHE); ii) TKIs associated to steroids with no chemotherapy (TKISTE); iii) chemotherapy-free combinations of blinatumomab plus TKIs (TKIBLI). According to the Shiny method, the three PFS curves were reported in a single Kaplan-Meier graph and subjected to survival statistics. In terms of PFS, TKIBLI ranked first, TKICHE second, and TKISTE third; the differences between these three regimens were statistically significant. In conclusion, the multi-treatment Kaplan-Meier graph generated in this study has effectively summarized the current evidence on these treatments in comparative terms.

The purpose of the present study was to investigate anti-staphylococcal activity of liposomal daptomycin, against four biofilm-producing S. aureus and S. epidermidis clinical strains, three of which are methicillin resistant. Neutral and negatively charged Daptomycin-loaded liposomes were prepared by three methods thin film hydration (TFH), DRV and microfluidic mixing (MM), and characterized for drug encapsulation (EE%), size distribution, zeta-potential, vesicle stability, drug release and drug integrity. Interestingly, whilst drug loading in THF and DRV nanosized (by extrusion) vesicles was around 30-35, very low loading (~4%) was possible in MM vesicles, requiring further explanatory investigations. Liposomal encapsulation protected daptomycin from degradation and preserve its bioactivity. Quantitative microtiter plate (crystal violet, CV), methylthiazoltetrazolium (MTT), and growth curve (GC) assays evaluated antimicrobial activity of neutral and negative charge daptomycin-liposomes towards planktonic bacteria and biofilms. Neutral liposomes exhibited dramatically enhanced inhibition of bacteria growth (compared to free drug) for all species studied, while negative charged liposomes were totally inactive. Biofilm prevention and treatment studies revealed high antibiofilm activity of liposomal daptomycin. Neutral liposomes were more active for prevention and negative charge ones for treating established biofilms. Planktonic bacteria as well as matured biofilms of low daptomycin susceptible MRSE and MRSA strains were almost completely eradicated by liposomal-daptomycin indicating the need for their further exploration as antimicrobial therapeutics.

Finding, safe and reliable alternatives to fungicides is one of the most actual challenges in agriculture. In this regard, our experiment investigated the effectiveness of different elicitors, botanical extracts and essential oils to control grey mould (Botrytis cinerea) and powdery mildew (Podosphaera aphanis) on strawberry plants. Furthermore, the defence mechanisms activated in plants after treatments were investigated. The trial was conducted in field conditions under plastic tunnel with strawberry plants ‘Elsanta’. In the first experiment, a group of strawberry plants was treated before flowering with elicitors [acibenzolar-S-Methyl – (BTH), chitosan], botanical extracts (seaweed extract, alfalfa hydrolysate) and essential oils (thyme and juniper) to evaluate their ability to reduce the incidence of grey mould infection on flowers. In the second experiment, another group of plants was treated before and after experimental inoculation with P. aphanis. Results indicated that the incidence of flower infected by B. cinerea was significantly reduced by thyme and juniper essential oils, showing values that were not significantly different from the commercial fungicide penconazole (positive control). As a consequence, final yield of essential oil-treated plants was +27% higher as compared to control. No significant differences emerged for other tested products against grey mould. However, gene expression analysis showed an up-regulation of FaEDS1, FaLOX and PR gene expression (FaPR1, FaPR5, FaPR10) in leaves treated with BTH. The other tested natural substances also elicited defence-related genes, however at a lower level than BTH. In the experiment, all treatments applied prior inoculation significantly reduced the incidence and severity of powdery mildew as compared to control. At 28 days after inoculation, chitosan and thyme essential oil applications performed similarly to their positive controls (BTH and penconazole, respectively), showing a significant reduction of disease incidence (by -84 and -92%) as compared to control. Post-inoculum application of essential oils showed similar effective action to fungicide (penconazole) in reducing incidence and severity of powdery mildew. These results indicate that the tested substances could be used as alternatives to fungicides for the control of grey mould and powdery mildew in strawberry, therefore representing a valuable tool for the control of these fungal diseases under the framework of the sustainable agriculture.

A compact 2-DOF (two degrees of freedom) piezoelectric-driven platform for 3D cellular bio-assembly systems has been proposed based on “Z-shaped” flexure hinges. Multiple linear motions with high resolution both in x and y directions are achieved. The “Z-shaped” flexure hinges and the parallel-six-connecting-rods structure are utilized to obtain the lowest working stress while compared with other types of flexure hinges. In order to achieve the optimized structure, matrix-based compliance modeling (MCM) method and finite element method (FEM) are used to evaluate both the static and dynamic performances of the proposed 2-DOF piezoelectric-driven platform. Experimental results indicate that the maximum motion displacements for x stage and y stage are lx=17.65 μm and ly=15.45 μm, respectively. The step response time for x stage and y stage are tx=1.7 ms and ty =1.6 ms, respectively.

One of the central criteria for free will is “Could I have done otherwise?” But because of a temporal asymmetry in human choice, the question makes no sense. The question is backward-looking, while human choices are forward-looking. At the time when any choice is actually made, there is as of yet no action to do otherwise. Expectation is the only thing to contradict (do other than). So the ability to do something not expected by the ultimate expecter, Laplace’s demon, is a better criterion for free will. If human action is fundamentally unpredictable, then we have free will. Scientists have studied a form of fundamental unpredictability, known as undecidability. The features that make a system capable of undecidable dynamics have been identified: program-data duality; potential to access an infinite computational medium; and the ability to implement negation. Humans have all three of these features, so we very likely are fundamentally unpredictable, so we have free will.

The broad and rapid application of new genomic techniques (NGTs) such as CRISPR-Cas has led to a fast increase in the number of genetically modified crops. With the recently published EU Commission’s (EC) regulatory proposal on plants generated with NGTs (July 5, 2023) the process of admission of such genetically modified plants is aimed to get accelerated and simplified. NGT plant applications shall be categorized based on their molecular characteristics into category 1 NGT (NGT1) and category 2 NGT (NGT2), which is in divergence from the current legislation centered around Directive 2001/18/EC. In the regulatory proposal NGT2 plants are envisioned to undergo a reduced risk assessment while for NGT1 plants no risk assessment is foreseen at all. To demonstrate were the path of the proposal leads to in practice, we applied the proposed criteria for categorization to a list of NGT plant applications that are currently in the commercialization pipeline. A key finding is that out of those plant applications affected by the EC proposal, 94% would be classified as NGT1 and thus would receive a market approval without risk assessment, monitoring and sufficient labeling provisions. The remaining 6% of applications would be classified as NGT2 plants for which, in deviation from the current regulation, an adapted risk assessment is proposed. A screening of intended traits in the pipeline highlights that certain NGT1 plants can pose similar environmental risks (e.g. invasiveness) compared to other genetically modified organisms (GMOs), as defined in Directive 2001/18/EC. For example, NGT1 applications based on RNAi technology can exhibit insecticidal effects with potential side effects on non-target organisms (i.e. other insects). Our quantitative and case-specific elaboration on how the current EC regulatory proposal would affect the environment, health or consumer protection will be informative for decision makers and politicians.

This paper investigates the impact of debt financing on dividend payments when they face the agency costs of free cash flow. Focusing on a sample of 120 firms listed on the Saudi Stock Exchange during the period 2011-2021. The study found a negative association between agency cost of free cash flow and dividend payment. More importantly, our research highlights the significant role of long-term debt in making more prudent use of free cash flow. The obligation to meet interest and principal payments acts as an incentive for them to steer clear of unprofitable expenses and risky investments. Concurrently, long-term debt imposes restrictive clauses in debt contracts, such as minimum dividend distribution requirements, which further encourage higher dividend payments. Since interest and debt repayments are fixed obligations, using free cash flow for dividend disbursement is considered a more profitable and beneficial approach for shareholders in the context of Saudi Arabia.

A typical halogen-free flame-retardant (HFFR) formulation for electric cables may contain polymers, various additives, and fire-retardant fillers. In this study, composites are prepared by mixing natural magnesium hydroxide (n-MDH) with linear low-density polyethylene (LLDPE) and a few types of ethylene-octene copolymers (C₈-POE). Depending on the content of LLDPE and C₈-POE, we obtained composites with different crystallinity that affected the final mechanical properties. The nucleation effect of the n-MDH and the variations in crystallinity caused by the blending of C₈-POE/LLDPE/n-MDH were investigated. In the C₈-POE/LLDPE blend, we found a decrease in the crystallization temperature of LLPDE compared to pure LLDPE and an increase in the crystallization temperature of C₈-POE compared to pure C₈-POE. On the contrary, the addition of n-MDH led to an increase in the crystallization temperature of LLDPE. As expected, the increase in the crystallinity of the polyolefin matrix of composites led to higher elastic modulus, higher tensile strength, and lower elongation at break. Overall, these results show how to obtain the required mechanical features for halogen-free flame-retardant compounds for electric cable applications depending on the quantities of the two miscible components in the final blend.

Agriculture is a vital component of Egypt's economy; therefore, using Digital Elevation Models (DEMs) in agricultural planning in Egypt has significant benefits regarding water management, site appropriateness assessment, flood risk mitigation, and infrastructure construction. It is also essential for planners to make more informed decisions, optimize resource allocation, and support sustainable farming practices. This research paper investigates the accuracy of obtaining DEM data from four free global models (STRM30, ALOS30, COP30, and TanDEM-X90). The global DEM data has been compared to an actual GNSS-RTK DEM data surveyed onsite for two agricultural block areas in Aswan, the southern Government of Egypt. The two blocks are a part of a national project. For Block I and II, the RMSE of the Model STRM30 was 2.92 m and 3.59 m, respectively, indicating a poorer solution. Regarding accuracy, the ALOS30 model ranks third, reporting an RMSE of 2.58 m for block II and 3.30 m for block I. COP30 has an RMSE value of 1.06 m for blocks I and II and.91 m overall. TanDEM-X90 is the most accurate model in this investigation; block I provided an RMSE of 0.90 m with an SD of 0.58 m (SD95% = 0.38 m). After removing the anomalies, the model's stated RMSE for block II was 0.34 m, with an SD value of 0.62 m and 1.03 m. According to the classification using machine learning algorithms, with an accuracy of 84.7% for block I and 85% for block II, TanDEM-X90 is the best solution.