We search for limit cycles in the dynamical model of two-species chemical reactions that contain seven reaction rate coefficients as parameters and at least one third-order reaction step, that is, the induced kinetic differential equation of the reaction is a planar cubic differential system. Symbolic calculations were carried out using the Mathematica (or, Wolfram language) mathematical program package, and it was also used for the numerical verifications to show the following facts: the kinetic differential equations of these reactions each has two limit cycles surrounding the stationary point of focus type in the positive quadrant. In the case of Model 1, the outer limit cycle is stable and the inner one is unstable that appears in a supercritical Hopf bifurcation. Moreover, the oscillations in a neighborhood of the outer limit cycle are slow-fast oscillations. In the case of Model 2, the outer limit cycle is unstable and the inner one is stable. With another set of parameters, the outer limit cycle can be made stable and the inner one unstable.

The response of carbon fixation in C3 plants to elevated CO2 is relatively larger when photosynthesis is limited by carboxylation capacity (VC) than when limited by electron transport (J). Recent experiments under controlled, steady-state conditions have shown that photosynthesis at elevated CO2 may be limited by VC even at limiting PPFD. These experiments were designed to test whether this also occurs in dynamic field environments. Leaf gas exchange was recorded every 5 minutes using two identical instruments both attached to the same leaf. The CO2 concentration in one instrument was controlled at 400 mol mol-1 and one at 600 mol mol-1. Leaves were exposed to ambient sunlight outdoors, and cuvette air temperatures tracked ambient outside air temperature. The water content of air in the leaf cuvettes was kept close to that of the ambient air. These measurements were conducted on multiple, mostly clear days for each of three species, Glycine max, Lablab purpureus, and Hemerocallis fulva. The results indicated that in all species, photosynthesis was limited by VC rather than J at both ambient and elevated CO2 both at high midday PPFDs and also at limiting PPFDs in the early morning and late afternoon. During brief reductions in PPFD due to midday clouds, photosynthesis became limited by J, The net result of the apparent deactivation of Rubisco at low PPFD was that the relative stimulation of diurnal carbon fixation at elevated CO2 was larger than would be predicted when assuming limitation of photosynthesis by J at low PPFD.

In the paper, we prove a joint limit theorem in terms of weak convergence of probability measures on $\mathbb{C}^2$ defined by means of the Epstein ζ(s;Q) and Hurwitz ζ(s,α) zeta-functions. The limit measure in the theorem is explicitly given. For this, some restrictions on the matrix Q and parameter α are required. The theorem obtained extends and generalizes Bohr-Jessen’s results characterising asymptotic behaviour of the Riemann zeta-function.

Considering the significance of thermodynamic cycles in the global energy system, it is necessary to develop new general classes of thermodynamic cycles to relieve current energy and environmental problems. Inspired by the relationship between power cycles and refrigeration cycles, we realize that general classes of thermodynamic cycles should occur in pairs with opposite functions. Here we reverse class 1 heating cycles to obtain another new general class of thermodynamic cycles named class 2 heating cycles (HC-2s). HC-2s have two basic forms, and each contains six thermodynamic processes. HC-2s present the simplest and most general approach to utilizing the temperature difference between a medium-temperature heat source and a low-temperature heat sink to achieve efficient high-temperature heating. HC-2s fill the gaps that have existed since the origin of thermal science, and they will play significant roles in the global sustainable energy system.

Thermodynamic cycles are not only the core concepts of thermal science, but also key approaches to energy conversion and utilization. So far, power cycles and refrigeration cycles have been the only two general classes of thermodynamic cycles. While diverse types of systems have been developed to perform thermodynamic cycles, no new general classes of thermodynamic cycles have been proposed. Based on the basic principles of thermodynamics, here we propose and analyze a new general class of thermodynamic cycles named class 1 heating cycles (HC-1s). Two basic forms of HC-1s are obtained by connecting six essential thermodynamic processes in the proper order and forming a thermodynamic cycle. HC-1s present the simplest and most general approach to utilizing the temperature difference between a high-temperature heat source and a medium-temperature heat sink to achieve efficient medium-temperature heating and/or low-temperature cooling. HC-1s fill the gaps that have existed since the origin of thermal science, and they will play significant roles in energy conservation and emission reduction.

Counting in terms of cycles allows modeling many processes of Nature. We make use of a slight numerical incongruence within the numbering system to find a translational mechanism which connects sequential ↔ commutative properties of assemblies. The algorithms allow picturing the logical syntax Nature uses when reading the DNA. Ordering a collection on two different properties of its members will impose two differing sequences on the members. The coordinates of a point on a plane of which the axes are the two sorting orders sidestep the logical contradiction arising from the different linear assignments. During a reorder, elements aggregate into cycles. Using an etalon collection of simple logical symbols (which are pairs of natural numbers), which we reorder, we see typical movement patterns along the path of the string of elements that are members of the same cycle. We split the {value, position} descriptions of a natural number and observe the places the unit occupies at specific instances of time among its peers, while being a member of a cycle, under different orders prevailing. Which places elements occupy among their peers, under specific order conditions, is determined by numeric properties of the natural numbers that make up the element. The model presented is therefore tautologic, and can be compared to a hybrid of sudokus with the ultimate form of Rubik‘s cube. It is necessary for the reader to do some self-education on the matter of cycles as a prerequisite to understanding the working principle of the model. The contraption being a new development, it can’t have references in literature.One cannot lose a bet on the idea that sorting and ordering a collection of elementary logical elements will turn up typical patterns and that these archetypes of patterns will be of interest to Theoretical Physics, Chemistry, Biology, Information Theory, and some other fields, too.

In the century and a half since Maxwell first conjured his “finite being” which Lord Kelvin subsequently dubbed a “daemon”, researchers have explored the connections between non-equilibrium thermodynamics, entropy, and information theory. In recent years various Thermodynamic Uncertainty Relations (TURs) have been derived to inform upon the relationship between the entropy production and the precision possible in thermodynamic machines and processes. In this paper the recently derived TURs are applied to the hypothetical thermodynamic economy as described by Parker [1]. The TURs define the lower bound on the total entropy production of the economy. Changes in this entropy production rate has consequences on the stability of the economic system and plays a central role in the business cycle. This new perspective has important implications for policy makers, researchers, and other economic actors.

The historic view of metadata as “data about data” is expanding to include data about other items that must be created, used and understood throughout the data and project life cycles. In this context, metadata might better be defined as the structured and standard part of documentation and the metadata life cycle can be described as the metadata content that is required for documentation in each phase of the project and data life cycles. This incremental approach to metadata creation is similar to the spiral model used in software development. Each phase also has distinct users and specific questions they need answers to. In many cases, the metadata life cycle involves hierarchies where latter phases have increased numbers of items. The relationships between metadata in different phases can be captured through structure in the metadata standard or through conventions for identifiers. Metadata creation and management can be streamlined and simplified by re-using metadata across many records. Many of these ideas are being used in metadata for documenting the life cycle of research projects in the Arctic.

The rock joint fissure slope in cold regions is prone to deformation and failure problems such as relaxation, tension and collapse under freeze-thaw (F-T) cycles. Based on the ideology of clean production and promoting the structural integrity of geotechnical projects in cold areas, this study designed and prepared aeolian-sand (AS) to replace part of river sand as a filling mortar material by taking advantage of the low cost and easy availability of AS. Investigations were carried out to determine the impact of varying proportions of AS in mortar on the microstructure and shear properties of the mortar-rock interface under F-T cycles. Therefore, F-T cycle testing, nuclear magnetic resonance (NMR) testing and shear testing were carried out on grout with different proportions of AS. The results show that the right proportion of AS replacement could enhance the shear deformation resistance and F-T resistance of the mortar-rock interface, and 30% proportion is the optimal proportion. By increasing of F-T cycles, the three types of specimens showed different degrees of particle spalling, shedding and cracking. The slurry-rock interface layer in the A (0%) group exhibited the most severe F-T deterioration, while the B (15%) group showed a lesser degree, and the C (30%) group performed the best. T2 spectrum curve and total spectrum area change law from the microscopic point of view to verify the 30% AS proportion mortar-rock interface F-T resistance is the strongest, followed by 15% AS proportion mortar, the weakest is ordinary mortar. The degradation of the mortar-rock bond is primarily due to the conversion of solid to liquid phases and the movement of internal water caused by fluctuating temperatures. The extent of F-T deterioration in the slurry-rock interface layer is greatly affected by the varying proportions of AS. The shear strength and shear stiffness of specific proportion of AS decreased with the increase of F-T cycles. For same F-T cycles, the shear strength and shear stiffness of group C (30%) were the highest, followed by group B (15%) and group A (0%). The grout material not only reinforces the F-T joint fissure slope, but also reduces the cost of grout reinforcement and promotes the clean production of geotechnical structures.

Age-related diseases (ARDs) are the leading cause of death worldwide, and contribute to 90% of mortality in developed countries. Interestingly, the mortality rates of individual ARDs increase exponentially with age. Processes described by the exponential growth function typically involve a branching chain reaction or, more generally, a positive feedback loop. Here I propose that each ARD is mediated by one or several positive feedback loops (vicious cycles). I then identify critical vicious cycles in five major ARDs: atherosclerosis, hypertension, diabetes, Alzheimer’s and Parkinson’s. I also propose that the progression of ARDs can be halted by selectively interrupting the vicious cycles and suggest the most promising targets. An evolutionary perspective is also offered.

Natural cycles underpin the very stuff of life. In this commentary we consider unnatural cycles: that is, anthropogenic activities which have a circularity, but whose nature is to have a detrimental effect on human health, exacerbating existing problems. Natural cycles have feedback loops, some of which have recently come to light, with an understanding that everything is connected in some way. In health, feedback loops are imperative in homeostatic mechanisms. However, in the unnatural cycle the feedback loops serve to reinforce (and in some cases amplify) negative problems. We offer a commentary on an unnatural cycle moving from air quality to lung function and back to air quality; we call this the lung disease unnatural cycle. We suggest where links occur, and where wider consideration of interactions between various disciplines can lead to breaking this unnatural (or vicious) cycle, changing it to a healthy cycle where individual health can be improved, along with better global scale outcomes. We suggest that many activities within this unnatural cycle occur within silos. However, the improved cycle incorporates joint activities at geological, health, and financial levels, to the mutual benefit of all, breaking the unnatural cycle, and improving health, life and financial costs.

This paper generalizes the actuator disc theory to the application of crosswind kite power systems. For simplicity, it is assumed that the kite sweeps an annulus in the air, perpendicular to the wind direction (i.e. straight downwind configuration with tether parallel to the wind). It is further assumed that the wind flow has a uniform distribution. Expressions for power harvested by the kite is obtained, where the effect of the kite on slowing down the wind (i.e. the induction factor) is taken into account. It is shown that although the induction factor may be small for a crosswind kite (of the order of a few percentage points), neglecting it in calculations may result in noticeable overestimation of the amount of power harvestable by a crosswind kite system.

The study aimed to determine the effect of heat stress (HS) on reproductive parameters [calving to first service (CTFS) and first service conception rate (FSCR)] and general physiological responses [rectal temperature (RT) and respiratory rate (RR)] in tropical Holstein Friesian dairy cows raised in Ratchaburi province, Thailand. Cows were divided into a moderate HS (n = 22) and a mild HS (n = 22) group. Cycling cows were detected and injected with PGF2α at the beginning of the experimental period. Reproductive and physiological parameters were recorded. The average temperature humidity indices experienced by the cows were 80.67 ± 0.79 and 77.81 ± 1.09 for the moderate and mild HS groups, respectively. Cows showed significantly lower RT and RR in the mild (38.47 ± 0.21°C and 41.04 ± 4.55 bpm, respectively) than in the moderate HS group (38.87 ± 0.15°C and 51.17 ± 10.52 bpm). Under mild HS, cows showed a better response to injection of PGF2α than those under moderate HS. The percentage of cows that ovulated after being induced by PGF2α and showed estrus signs was higher in the mild than the moderate HS groups (54.55% versus 18.18%). Furthermore, the FSCR of cows under mild HS tended to be higher than in the moderate HS group (54.55 % and 42.11%, respectively), while the average CTFS interval was significantly shorter under mild than moderate HS (69.47 ± 18.18 and 84.60 ± 27.68, respectively). These results indicate that HS impairs reproductive performance in cross-bred Holstein cows, especially in moderate HS conditions.

Cholera is an acute enteric infectious disease caused by the Gram-negative bacterium Vibrio Cholerae. Despite a huge body of research, the precise nature of its transmission dynamics has yet to be fully elucidated. Mathematical models can be useful to better understand how an infectious agent can spread and be properly controlled. We develop a compartmental model describing a Human population, a bacterial population as well as a phage population. We show that there might be eight equilibrium points; one of which is a disease free equilibrium point. We carry out numerical simulations and sensitivity analyses and we show that the presence of phage can reduce the number of infectious individuals. Moreover, we discuss the main implications in terms of public health management and control strategies.

Climate change is one of the main issues that humanity is currently facing due to carbon dioxide emissions caused by the use of fossil fuels. Organic Rankine cycles may play an important role in reducing these emissions since they can be operated by using industrial waste heat of renewable energies. The present study presents a comprehensive bibliographic review of organic Rankine cycles. The study not only actualizes previous reviews that mainly focused on basic cycles operating on subcritical or supercritical conditions but also includes the analysis of novel cycles such as two-stage and hybrid cycles and the used fluids. Recuperative and regenerative cycles are more efficient than reheated and basic single-stage cycles. The use of two-stage cycles makes it possible to achieve higher thermal efficiencies and net power outputs of up to 20% and 44%, respectively, compared with those obtained with single-stage cycles. Theoretical studies show that hybrid systems, including Brayton and organic Rankine cycles, are the most efficient; however, they require very high temperatures to operate. Most organic Rankine cycle plants produce net power outputs from 1 kW up to several tens of kW, mainly using microturbines and plate heat exchangers.

The calculation of the collapse load of spherical domes is addressed using a semi-analytical approach under the hypotheses of small displacements and perfect plasticity. The procedure is based on the numerical approximation of the self-stress that represents the projection of the balance equilibrium null space on a finite dimensional manifold. The so obtained self-equilibrated stress span is superimposed to a finite element linear elastic solution to the prescribed loads yielding to the statically admissible set accordingly to Melan’s theorem. The compatibility of the stress with the constitutive law of the material has been enforced using linearized limit domain in terms of generalized stress, namely axial force and bending moment along the local spherical curvilinear coordinates. The procedure has been tested with reference to numerical and experimental data from the literature confirming the accuracy of the proposed method. The comparison with the literature confirms that the buckling load is much greater than the plastic collapse loads both calculated through the proposed procedure and reported in the quoted literature.

In this paper we consider the congruence problem that arises in the post-analysis of Bayesian network models reconstructed from different datasets. Apart from the structure, a typical network numerically encodes relationship intensities, assigning numerical score to network edges via the scoring criterion used in the reconstruction process. This scoring is rarely a directly interpretable quantity with proper units of measure and an absolute scale, and often comes short in desirable characteristics of a true metric. This leads to poor portability of edge magnitude considerations between similar networks, originating from different sources. In this work, we address this problem by estimating the effect that data-specific resolution limit has on conditional independence, as reflected by information-theoretic entropy, and by the appropriate modification of MDL score, which removes the inconsistency between the score components in both the meaning and units. We also numerically validate our findings and expose additional performance advantages obtained via this modification.

This paper studies pandemic viruses that spread during the period (1759–2020) according to solar activity cycles. Our findings and results include the following: (1) The severity of a pandemic correlates negatively with the strength of solar activity; (2) Pandemic viruses are classified into three types based on their compatibility with solar activity associations. Most of them spread through the quiet Sun, where viruses survive better in cold and rainy weather, and in stable geomagnetic fields without strong disturbances; (3) The emergence of new strains of influenza viruses was manifested in two ways. First, the annual epidemics due to antigenic drift. Second, pandemics recur every 1–12 solar cycles (about 11–120 years) due to viral reassortment of new subtypes, which results in antigenic shifts; (4) Pandemic viruses have two groups according to their recurring period: first, recurring in nine solar cycles; second, recurring in twelve solar cycles. Furthermore, we reassort pandemic viruses from their previous spread in the same periodic classification. Moreover, we derive a periodicity formula for each subtype of the pandemic virus as a spread date.

In the author's opinion, many global problems that face humanity - in the fields of education, medicine, management etc can be tackled more effectively if the cyclic nature of self-reproducing systems – including living beings – is taken into account. Summarizing the main physiological findings of the last decades on "adaptation reactions", one can very roughly say that the way of action which is effective in the sense of productive activity of people happens at the same time to be healthy, and it gives the participants of the process the feeling of happiness. The present paper represents a very short overview of the contemporary concepts of the adaptation reactions based on the fundamental understanding of their cyclic nature due to general properties of self-reproducing systems. One interesting feature of self-reproduction cycles is its first "phase of orientation" which was not discussed in detail in the past but plays a key role in the whole cycle.

Based on the nonlinear failure criterion and modified tangential technique, the upper bound solutions of supporting pressure on the deep tunnel face were obtained under pore water pressure conditions. The influence of parameters on the supporting pressure and collapse range was investigated according to the unlimited block failure mechanism. It is found that the upper bound solutions of supporting pressure increase with the growth of the nonlinear coefficient and pore water pressure coefficient. The collapse range of the tunnel face scales out with the increase of the nonlinear coefficient and shrinks when increasing the pore water pressure coefficient. Moreover, with the increase of the nonlinear coefficient, the impact strength on supporting pressure and collapse range declines gradually. According to the calculating results, it is manifest that both the pore water pressure and nonlinear criterion factors have negative impacts on the stability of the tunnel face. Thus, more attention should be paid to these parameters to ensure face stability in deep tunnel construction.

This is the second paper in a cycle investigating the exact solution of loop equations in decaying turbulence. We perform numerical simulations of the Euler ensemble, suggested in the previous work, as a solution to the loop equations. We designed novel algorithms for simulation, which take a small amount of computer RAM so that only the CPU time grows linearly with the size of the system and its statistics. This algorithm allows us to simulate systems with billions of discontinuity points on our fractal curve, dual to the decaying turbulence. For the vorticity correlation function, we obtain \textbf{quantum fractal laws} with regime changes between universal discrete values of indexes. The traditional description of turbulence with fractal or multifractal scaling laws does not apply here. The measured conditional probabilities of fluctuating variables are smooth functions of the logarithm of scale, with statistical errors being negligible at our large number of random samples $T = 167,772,160$ with $N = 200,000,000$ points on a fractal curve. The quantum jumps arise from the analytical distribution of scaling variable $X = \frac{\cot^2(\pi p/q)}{q^2}$ where $\frac{p}{q}$ is a random fraction. This distribution is related to the totient summatory function and is a discontinuous function of $X$. In particular, the energy spectrum is a devil's staircase with tilted uneven steps with slopes between $-1$ and $-2.03$. The logarithmic derivative of energy decay $n(t)$ as a function of time is jumping down the stairs of universal levels between $1.50$ and $1.53$. The quantitative verification of this quantization would require more precise experimental data.

Numerical simulations of standard situations in the transition region from gas kinetics to fluid dynamics at small Mach numbers indicate a clear dependence of the simulation results on the underlying kinetic model (here: nonlinear and linearized Boltzmann collision operator vs. BGK relaxation model). We develop an improved mathematical framework (trace theory) to explain these differences. In particular we reveal certain deficiencies for the classical BKG system as well as for the standard Navier Stokes approach.

We propose a class of stochastic models for a dynamics of limit order book with different type of liquidities. Within this class of models we study the one where a spread decreases uniformly, belonging to the class of processes known as a population processes with uniform catastrophes. The law of large numbers (LLN), central limit theorem (CLT) and large deviations (LD) are proved for our model with uniform catastrophes. Our results allow us to satisfactorily explain the volatility and local trends in the prices, relevant empirical characteristics that are observed in this type of markets. Furthermore, it shows us how these local trends and volatility are determined by the typical values of the bid-ask spread. In addition, we use our model to show how large deviations occur in the spread and prices, such as those observed in flash crashes.

We investigate a new fundamental property of infectious diseases with natural adaptive immunity that weakens over time. Numerical experiments with a model of the Covid-19 epidemic in Moscow have demonstrated that when the reproduction number R0 is about 4, a qualitative change (bifurcation) occurs in the behavior of the virus-human system. Below this value, the long-term forecast tends to undamped oscillations; above it, the forecast shows damped oscillations: the amplitudes of epidemic waves decrease gradually, with a constant, very high background level of morbidity that keeps the natural immunity near 100%. To confirm this result analytically, we use an original modification of the Euler-Lotka renewal equation, which describes the dynamics of infected patients distributed by disease duration (time since infection) and accounts for immunity. To construct a bifurcation diagram, which illustrates the dependence of the equilibrium stability on the parameter R0, we linearize the equation in the vicinity of the equilibrium point and examine its numerical approximation (discrete form). This approximation can be interpreted as a Leslie model, with the matrix elements dependent on the parameter R0. By examining the roots of the corresponding Lotka polynomial, we can assess the stability of the equilibrium point. For the bifurcation diagram, we use the functions obtained from the simulation of the Covid-19 epidemic in Moscow. However, observations of the epidemic in other cities and countries support the primary finding of our study regarding the attenuation of epidemic waves.

We derive a quantum speed limit for unitary evolution for the case of mixed quantum states using the stronger uncertainty relation for mixed quantum states. This bound can be optimized over different choices of Hermitian operators for a better bound. We illustrate this with some examples and show its better performance with respect to three existing bounds for mixed quantum states.

Response of tomato and eggplant to continuous lighting (CL) and abnormal light/dark (L/D) cycles was studied to elucidate the role of the absence of the dark period in the diurnal cycle in the development of leaf injuries under CL. Four light treatments were set: 16/8 h (control), 24/0 h (CL), 6/6 h, and 24/24 h (abnormal L/D cycles). These light treatments provided average daily light integrals of 17.3, 25.9, 13.0 and 13.0 mol m-2 day-1, respectively. Results of this work have shown that in both tomato and eggplant abnormal L/D cycles caused photoinhibition and leaf injuries similar to those in CL-grown plants. Induced defense mechanisms were not strong enough to contend against oxidative stress caused by light treatments that provided plants with even smaller DLI than 16/8 h photoperiod did. Half time during abnormal L/D cycles were dark periods. Despite these facts, abnormal L/D cycles were injurious. It is concluded that photooxidative stress induced by CL can not be attributed to excessive DLI or the continuity of light itself (the absence of dark periods). Therefore, we believe that the hypothesis suggesting circadian asynchrony to be the main triggering factor of CL-induced leaf injuries is the most plausible among many others proposed.

Thermal-based actuators are known for generating large force and displacement strokes at mesoscale (millimeter) regime. In particular, two-phase thermal actuators are found to benefit from the scaling laws of physics at mesoscale to offer large force and displacement strokes; but they have low thermal efficiencies. As an alternative, a combustion-based thermal actuator is proposed and its performance is studied in both open and closed cycle operations. Through a physics-based lumped-parameter model, we investigate the behavior and performance of the actuator using a spring-mass-damper analogy and taking an air standard cycle approach. Three observations are reported: (1) the mesoscale actuator can generate peak forces of up to 400 N and displacement strokes of about 16 cm suitable for practical applications; (2) an increase in heat input to the actuator results in increasing the thermal efficiency of the actuator for both open and closed cycles; and (3) for a specific heat input, both the open and closed cycle operations respond differently \textemdash different stroke lengths, peak pressures, and thermal efficiencies.

We derive some Quantum Central Limit Theorems for expectation values of macroscopically coarse-grained observables, which are functions of coarse-grained hermitean operators consisting of non-commuting variables. Thanks to the hermicity constraints, we obtain positive-definite dis- tribution for the expectation values of observables. These probability distributions open some pathway for an emergence of classical behaviours in the limit of in nitely large number of identical and non-interacting quantum constituents. This is in contradistinction to other mechanisms of classicality emergence due to environmental decoherence and consistent histories. The probabil- ity distributions so derived also enable us to evaluate the nontrivial time-dependence of certain differential entropies.

Fatigue remains a challenge especially for high end metal AM parts and materials. From a design perspective, the fatigue limit of an AM solution can be improved upon by optimizing the manufacturing process for a certain material and part. In addition, improved accuracy of design methodologies aids in capturing the features critical for fatigue and quantifies their significance to desired part lifetime as well as providing a basis for their avoidance. In current work we present an overall concept merging thermomechanical process and powder bed solidification modeling to micromechanical analysis of fatigue of the resulting material microstructure. Material features critical to fatigue, particularly surface roughness, internal defects such as porosity and cracks and on the other hand inclusions, can be assessed directly on the basis of AM part microstructure with respect to the resulting fatigue limit. Case analyses consist of maraging steel and nickel alloys. The overall scheme provides a basis for optimization of metal AM solutions against fatigue and multiscale modeling founded basis for fatigue design.

As a system becomes more complex, at first, its description and analysis becomes more complicated. However, a further increase in the system’s complexity often makes this analysis simpler. A classical example is Central Limit Theorem: when we have a few independent sources of uncertainty, the resulting uncertainty is very difficult to describe, but as the number of such sources increases, the resulting distribution get close to an easy-to-analyze normal one – and indeed, normal distributions are ubiquitous. We show that such limit theorems make analysis of complex systems easier – i.e., lead to blessing of dimensionality phenomenon – for all the aspects of these systems: the corresponding transformation, the system’s uncertainty, and the desired result of the system’s analysis.

The theoretical limit of link prediction is a fundamental problem in this field. Taking the network structure as object to research this problem is the mainstream method. This paper proposes a new viewpoint that link prediction methods can be divided into single or combination methods, based on the way they derive the similarity matrix, and investigates whether there a theoretical limit exists for combination methods. We propose and prove necessary and sufficient conditions for the combination method to reach the theoretical limit. The limit theorem reveals the essence of combination method that is to estimate probability density functions of existing links and nonexistent links. Based on limit theorem, a new combination method, theoretical limit fusion (TLF) method, is proposed. Simulations and experiments on real networks demonstrated that TLF method can achieve higher prediction accuracy.

The most important prognostic factors in curatively treated prostate cancer at the initial diagnosis are T and N stage, histological subtype, Gleason score, initial PSA, PSA density and percentage of core biopsy positivity. Newer, but non-standard prognostic factors are urine PCA3 and genetic markers of prostate cancer. A simple, but seemingly underestimated standard test is serum Calcium (Ca) level, which has been shown by a previous study group to be a good predictor of lethal prostate cancer, but there is scarce evidence regarding the prognostic value of calcium levels at diagnosis. We aimed to determine whether a Ca level in the upper part of normal values has a prognostic value in curatively treated prostate cancer. We have retrospectively included 84 consecutive patients with prostate cancer, who underwent curative radiotherapy (primary or adjuvant; external beam RT with or without brachytherapy). We have performed statistical analysis of available prognostic factors. Ca level at diagnosis was found to be a statistically significant predictor of disease-free survival.

Group-IV GeSn photodetectors (PDs) compatible with standard complementary metal-oxide-semiconductor (CMOS) processing have emerged as a new and non-toxic infrared detection technology to enable a wide range of infrared applications. The performance of GeSn PDs is highly dependent on the Sn composition and operation temperature. Here, we develop theoretical models to establish a simple rule of thumb, namely “GeSn-rule 23”, to describe GeSn PDs’ dark current density in terms of operation temperature, cutoff wavelength, and Sn composition. In addition, analysis of GeSn PDs’ performance shows that the responsivity, detectivity, and bandwidth are highly dependent on operation temperature. This rule provides a simple and convenient indicator for device developers to estimate the device performance at various conditions for practical applications.

In engineering practice, one can often encounter issues related to optimization where the goal is to minimize material consumption, minimize stresses or deflections of the structure. In most cases, these issues are addressed with finite element analysis software and simple optimization algorithms. However, in the case of optimization of certain structures, it is not co straightforward. An example of such constructions are bubble deck ceilings, where in order to reduce the dead weight, air cavities are used, which are regularly arranged over the entire surface of the ceiling. In the case of these slabs, the flexural stiffness is not constant in all its cross-sections, which means that the use of structural finite elements (plate or shell) for static calculations is not possible, and therefore the optimization process becomes more difficult. The paper presents a minimization procedure of the weight of bubble deck slabs using numerical homogenization and sequential quadratic programming with constraints. Homogenization allows to determine the effective stiffnesses of the floor, which in the next step are sequentially corrected by changing the geometrical parameters of the floor and voids in order to achieve the assumed deflection. The presented procedure allows to minimize the use of material in a quick and effective way by automatically determining the optimal parameters describing the geometry of the bubble deck floor cross-section.

This work focuses on the bifurcation behavior before chaos phenomenon happens. Traditional numerical method is unable to solve the unstable limit cycle of nonlinear system. One algorithm is introduced to solve the unstable one, which is based one of the continuation method is called DEPAR approach. Combined with analytic and numerical method, the two stable and symmetrical equilibrium solutions exist through Fork bifurcation and the unstable and symmetrical limit cycles exist through Hopf bifurcation of Lorenz system. With the continuation algorithm, the bifurcation behavior and its phase diagram is solved. The results demonstrate the unstable periodical solution is around the equilibrium solution, besides the trajectory into the unstable area cannot escape but only converge to the equilibrium solution.

Wireless Sensor Network (WSN) and the sensing devices are considered part of the core components of the Internet of Things (IoT). Hence, the modeling of IoT-WSNs is fundamental to having a better understanding, management, and deployment of this kind of technology. A fundamental issue in WSN is energy consumption due to the inherent limitations of this resource in the sensor devices. On the other hand, several issues arise in heterogeneous scenarios due to the coexistence of different sensor devices. Therefore, the modeling process becomes challenging and must consider the different transmission and operation cycles and modes that the transmission protocol implements to assure successful functioning in terms of transmission, synchronization, and energy savings. A duty-cycled MAC WSN protocol (PSA-MAC) has been modeled based on a pair of two-dimensional Discrete-Time Markov Chain (2D-DTMC), whose solution in terms of stationary probability distribution is used by expressions that have been derived to evaluate the energy consumption of sensor devices that could be used for WSN-based IoT applications. Analytical results of average energy consumption are obtained, where the synchronization, data, and sleep periods of a full transmission cycle are considered in a heterogeneous scenario with different node classes and priority assignments. Also, the normal and awake operation cycles are considered to assure synchronization and energy savings. Moreover, the transmission schemes of SPT (transmission of single packets) and APT (transmission of packets in aggregation) are also considered in the model. These results are validated through discrete event-based simulations, and the obtained results are accurate.

This study aims to better understand students who attend the Basic Vocational Training Cycles (FPB) regarding the measures to ensure diversity. This quantitative research project approximates the perception of students concerning their passage through their previous studies and their satisfaction and goals after finishing the school year. The sample con-sists of 352 students from Cordoba (Spain). A questionnaire has been used which follows the CIPP model. After the exploratory factor analysis was completed with the different groups of items and their descriptive analysis, various tests were carried out to consider the hypotheses (Pearson's correlation (r), one-factor analysis of variance and repeated ANOVA measures). The results indicate that the educational interest of the students is ac-ademic and professional. Likewise, there is no relationship detected between the appear-ance of socio-professional goals and average academic levels and the attributions with re-spect to repetitions of previous courses, although these goals vary depending on the satis-faction shown by the students with respect to the cycles. We conclude that the course of the FPB influences the adoption of decisions regarding academic-professional projects.

One of society’s greatest challenges is sequestering vast amounts of carbon to avoid dangerous climate change without driving competition for land and resources. Here we assess the potential of an integrated approach based on enhancement of natural biogeochemical cycles in agro-ecosystems that stimulate carbon capture and storage while increasing resilience and long-term productivity. The method integrates plant photosynthesis in the form of (cover) crops and agroforestry which drives carbon capture. Belowground plant-carbon is efficiently stored as stable soil organic carbon (SOC). Aboveground crop and tree residues are pyrolyzed into biochar, which is applied to the soil reducing carbon release through decomposition. Enhanced weathering of basalt powder worked into the soil further captures and stores carbon, while releasing nutrients and alkalinity. The integrated system is regenerative, through enhanced virtuous cycles that lead to improved plant capture, biomass storage and crop yield, the prerequisites for large-scale carbon sequestration along with food security.

This article explores the geothermal resources of Kazakhstan's Zharkent Basin, with a specific focus on the high-temperature geothermal sources in the Almaty region of Southern Kazakhstan. The research aims to analyze the energy characteristics of the Organic Rankine Cycle (ORC) for harnessing low-enthalpy geothermal energy for small-scale electricity generation. A detailed thermodynamic model was developed, employing R134a as the working fluid. An in-depth analysis of the Zharkunak field (Zharkent, Almaty region) revealed that well 5539, with its notably high temperatures, offers the highest potential for geothermal electricity production, achieving an annual output of approximately 10,371 MWh. The total electric power output from the studied wells in the region is estimated at 20,111 MWh annually, representing a significant contribution towards sustainable energy production and reducing reliance on traditional coal-fired power plants. The study concludes that the Organic Rankine Cycle is not only a viable and efficient technology for utilizing low-enthalpy geothermal resources to generate electricity on a small scale, but also a key player in enhancing energy independence. By leveraging local geothermal energy, the Almaty region can significantly reduce its reliance on external energy sources, thereby fostering sustainable development and reducing environmental impacts.

This article explores the important role of traditional shipyards in the global maritime industry, covering aspects of construction, repair, and maintenance. With the advent of faster manufacturing techniques, traditional shipyards face important challenges such as planning errors, coordination problems, delivery delays, and underutilization of technology, which results in high costs, reduced productivity, and prolonged projects. The application of Manufacturing Cycle Efficiency (MCE) emerged as an important solution to significantly increase production efficiency. MCE empowers shipyards to deal effectively with waste, bottlenecks, and disruptions, thereby increasing performance, competitiveness, and profitability. Using a comprehensive approach that uses both qualitative and quantitative methods, including field surveys, and in-depth interviews in the traditional shipyards industry, this research identifies Non-Value-Added (NVA) processes, conducts process mapping, and calculates MCE. The findings reported in this article underscore the significant wastage in the production process, indicating an urgent need for improvement, given the current average MCE value of 67.08%, indicating considerable room for improvement. This article provides innovative perspectives on optimizing the traditional shipyards industry through production cycle efficiencies while offering actionable recommendations. Key focus areas include integrating management systems, adopting advanced technologies, and implementing sustainable strategies to improve MCE, especially by reducing non-value-added time wastage, such as inspection and storage. By implementing strategies that optimize production, minimize waste, and overcome the challenges of global competition, this research contributes to improving MCE. In conclusion, this study is an invaluable guide for industry stakeholders, enabling them to enhance their competitiveness and adapt effectively to a dynamic business environment.

We study in detail the influence of different chemical potentials (baryon, charged, strange, and neutrino) on how and how fast a free gas of quarks in the zero-temperature limit reaches the conformal limit. We discuss the influence of non-zero masses, the inclusion of leptons, and different constraints, such as charge neutrality, zero-net strangeness, and fixed lepton fraction. We also investigate for the first time how the symmetry energy of the system under some of these conditions approaches the conformal limit. Finally, we briefly discuss what kind of corrections are expected from perturbative QCD as one goes away from the conformal limit.

We consider subtleties of the horizon (null-hypersurface) limit in the Parikh-Wilczek Membrane Approach to Black Holes. Specifically, we refine the correspondence between the (projected) Einstein equations of gravity with matter and the Raychaudhuri-Damour-Navier-Stokes (RDNS) equations of relativistic hydrodynamics. For a general configuration of gravity with matter we obtain additional terms in the hydrodynamic equations, which include logarithmic derivarives of a parameter (the regularization function) determining the proximity of a stretched membrane to the BH horizon. Direct computation of the new terms for exact (Schwarzschild and Kerr) solutions to the Einstein equations results in vanishing the additions to the RDNS equations in the horizon limit. For spacetimes, which are not exact solutions to the Einstein equations, as, for instance, for space-time configurations mimicking black holes, taking into account new terms in the RDNS equations is the mandatory operation. We also comment the correspondence between the horizon limit of the Parikh-Wilczek Membrane Approach and the Gourgoulhon-Jaramillo method of a null-hypersurface description, as well as the link of the obtained results to our previous work on the Kerr black holes.

The Betz limit sets a theoretical upper limit for the power production by turbines expressed as a maximum power coefficient of 16/27. Betz’s theory is accurate and it is based on the calculation of kinetic energy.

In computational neuroscience, spiking neurons are often analyzed as computing devices that register bits of information, with each action potential carrying at most one bit of Shannon entropy. Here, I question this interpretation by using Landauer's principle to estimate an upper limit for the quantity of thermodynamic information that can be dissipated by a single action potential in a typical mammalian neuron. I show that an action potential in a typical mammalian cortical pyramidal cell can carry up to approximately 3.4e11 natural units of thermodynamic information, or about 4.9e11 bits of Shannon entropy. This result suggests that an action potential can process much more information than a single bit of Shannon entropy.

Keywords: keyword 1; keyword 2; keyword 3 (List three to ten pertinent keywords specific to the article yet reasonably common within the subject discipline.)

TLC and HPTLC in normal (NP) and reversed (RP) phase systems combined with densitometry were used to analyze caffeine, propyphenazone and paracetamol. Normal phase analyses were performed on five different stationary phases (chromatographic plates), testing three mobile phases. Reversed-phase analyses were performed on four different chromatographic plates using three mobile phases. Thus, it was checked whether analyses using TLC chromatographic plates could be as sensitive as those performed on HPTLC plates. For all analyzed biologically active substances, the limit of detection (LOD) was calculated, i.e. a parameter that describes the method sensitivity. It has been shown that using both TLC and HPTLC plates, it is possible to develop chromatographic conditions that enable the detection of caffeine, propyphenazone and paracetamol in amounts ranging from a dozen to several dozen µg/spot. In the reversed-phase (RP) system, lower LOD values for all tested compounds were obtained using TLC than HPTLC. However, using analyses in the normal phase system (NP), similar (of the same order) LOD values are obtained for caffeine, propyphenazone and paracetamol, both when using TLC and HPTLC plates. Therefore, for economic reasons, TLC plates should be recommended for analyses of caffeine, propyphenazone and paracetamol, which are several times cheaper than HPTLC plates.

We will try to use the approach of labeled cycle cover sum to count the number of hamiltonian cycles in a special type of bipartite graphs, with 4k + 2 vertices which can also be considered as an alternative method to check hamiltonicity in such bipartite graphs. This graph is such that, there exists at least 1 vertex which is not a part of any cycle of size 4m + 2 where m < k, in O∗(1.414n) time. The algorithm is inspired by Bjorklund’s approach where instead of working on the field of GF(2k), we will be working on C.

In light of the recent pandemic, several COVID-19 vaccines were developed, tested and approved in a very short time, a process that otherwise takes many years. Above all, these efforts have also unmistakably revealed the capacity limits and potential for improvement in vaccine production. This review aims to emphasize recent approaches for targeted rapid adaptation and production of vaccines from an interdisciplinary multifaceted perspective. Using literature research, stakeholder analysis and a value proposition canvas, we reviewed technological innovations on the pharmacological level, formulation, validation and resilient vaccine production to supply bottlenecks and logistic networks. We identified four main drivers to accelerate the vaccine product life cycle: computerized candidate screening, modular production, digitized quality management and a resilient business model with corresponding transparent supply chains. In summary, the results presented here can serve as a guide and implementation tool for flexible, scalable vaccine production to respond swiftly to pandemic situations in the future.

In this paper, we study the constrained minimization problem for an energy functional which is related to the following Kirchhoff type equation \begin{equation*} -\Big(\eta+b\big(\int_{\R^{3}}|\nabla u|^{2}dx\big)^{s}\Big)\Delta u+V(x)u=\mu u +\lambda|u|^{p}u,\end{equation*} where $b$ is a positive constant, parameters $\eta\geq0, \lambda>0$, exponents $s>0$, $0

A portable, electrical impedance spectroscopy device to monitor the bioimpedance’s resistive component of beef meat by injecting a sinusoidal current of 1mA at 65.5 kHz was developed. In 4 slaughtered beef both right and left longissimus dorsi muscles where trimmed and left muscle portion was frozen to -18° C up to 7^th day while right one was meantime maintained at 5° C. Median value of specific resistivity of not-frozen sample was about twice Ω cm^-1 with respect of that of frozen-thawed sample (P = 0.004). It was concluded that the device is reliable to monitoring the ripening of beef meat in situ.

The study investigates the evolution of soil pore structure and shear strength deterioration in compacted clayey soil under controlled wetting and drying (wd) cycles, which are expected to become more frequent due to climate change. Thirty soil samples were compacted at optimal moisture content and 90% of maximum dry density. These samples were then subjected to 0, 1, 5, 10, and 15 controlled wd cycles from saturation to the wilting point, and volumetric changes were recorded during each cycle. After the wd treatment, the soil samples were scanned using X-ray Computed Tomography (CT) at 50 μm resolution and then sheared under unconsolidated-undrained and consolidated-undrained conditions in a triaxial test. Significant shrinkage and swelling of soil samples were observed during wd cycles, with average volumetric strain fluctuating between +12% at saturation and -5% at the wilting point. X-ray CT visualisation and analysis revealed higher porosity, more prominent pores and increased pore length in soil samples with increasing wd cycles. Both undrained and effective soil shear strength markedly decreased with increasing wd cycles. CT-derived macroporosity and pore length were significant predictors of the soil's undrained and effective shear strength when exposed to wd cycles. The findings emphasise the considerable impact of climate change, specifically wd cycles, on clayey soil, highlighting the need for consideration in the design of earth-based infrastructure.

The bentonite slurry trenches are becoming increasingly popular in the excavation process of trenches, especially for diaphragm wall construction. The problem that needs to be addressed is the stability of bentonite slurry trenches. This paper presents a stability analysis of trenches with temporary support of bentonite slurry, with unit weights ranging from 10.5 to 12.0 kN/m3, in the realistic stratum: C3 in the Hue city area. The analysis employs the shear strength reduction technique (SSR) with Mohr-Coulomb materials for the numerical method to evaluate the factor of safety (FS). The finite element method (FEM) software program (RS) and the finite difference method (FDM) FLAC software were applied. Additionally, the limit equilibrium method (LEM) of Bell-Washbourne and three-dimensional (3D) Bishop are used for calculating trench stability. The analysis results show a good agreement between RS2 and FLAC2D and RS3 and FLAC3D. Secondly, upon comparison, it is noted that the safety factors of the 3D software programs (RS3, FLAC3D) are higher than those of the 2D software programs (RS2, FLAC2D), ranging from 52.3 to 63.0% for trench lengths of 6m. However, for trench lengths of 54m, the safety factor values in 2D and 3D are nearly equal. Thirdly, the safety factor of the Bell-Washbourne method (LEM) is lower than the numerical analysis methods (FLAC and RS programs). Using the three-dimensional numerical method appears to be effective for estimating stability.

Quantum noise limits the sensitivity of laser interferometric gravitational-wave detectors. Given the state-of-the-art optics, the optical losses define the lower bound of best possible quantum-limited detector sensitivity. In this work, we come up with the configuration which allows to saturate this lower bound by converting the signal recycling cavity to be a broadband signal amplifier using an active optomechanical filter. We will show the difference and advantage of such a broadband signal recycling scheme compared with the previous white-light-cavity scheme using the optomechanical filter in [Phys.Rev.Lett.115.211104 (2015)]. The drawback is that the new scheme is more susceptible to the thermal noise of the mechanical oscillator. To suppress the radiation pressure noise which rises along with the signal amplification, squeezing with input/output filter cavities and heavier test mass are used in this work.

This paper presents some aspects of command and control of the new generation of machines-tools with numerical control. A problem faced by numerical control programmers is related to the length (relatively long) of the programs, with implications in the costs and duration of the manufacturing preparation. A method of reducing the main program and other redundant expenses is the introduction and use of processing cycles and subroutines for automatic calculation of the cutting tool trajectory, a fact that also allows the optimization and simplification of numerical control programming on flexible order manufacturing systems numeric. The method involves the use of predefined cycles and appropriate subroutines in order to improve the efficiency of the programming activity in a balanced way. It is a new and rapid method for optimize the structure of program using the numerical subroutine for command the movement of tool, in our case, with application for turning and milling.

Exposure of experimental rodents to controlled cycles of light, food, and temperature is important when investigating alterations in circadian cycles that profoundly influence health and disease. However, applying such stimuli simultaneously is difficult in practice. Our aim was to design, build, test, and open-source describe a simple device that subjects a conventional mouse cage to independent cycles of physiologically relevant environmental variables. The device is based on a box enclosing the rodent cage to modify the light, feeding, and temperature environments. The device provides temperature-controlled air conditioning (heating or cooling) by a Peltier module and includes programmable feeding and illumination. All functions are set by a user-friendly front panel for independent cycle programming. Bench testing with a model simulating the CO2 production of mice in the cage showed: a) suitable air renewal (by measuring actual ambient CO2), b) controlled realistic illumination at the mouse enclosure (measured by a photometer), c) stable temperature control, and d) correct cycling of light, feeding, and temperature. The cost of all the supplies (retail purchased by e-commerce) was &lt; 300 US$). Detailed technical information is open-source provided, allowing for any user to reliably reproduce or modify the device. This approach can considerably facilitate circadian research since using one of the described low-cost devices for any mouse group with a given light-food-temperature paradigm allows for all the experiments to be performed simultaneously, thereby requiring no changes in the light/temperature of a general-use laboratory.

In order to study the acoustic emission characteristics of sandstone under the action of the high temperature-water cooling cycle, the RMT-150B electro-hydraulic servo rock test system and the DS-5 acoustic emission detection and analysis system were used to conduct a single analysis of the sandstone after the high temperature-water cooling cycle. Experimental study on acoustic emission characteristics under axial compression, analyzing the deformation, strength and acoustic emission characteristics of sandstone under different temperatures and cycles. The results of the study show that the high temperature-water cooling action causes changes in the physical properties of the sandstone. The expansion rate of the rock sample decreases first and then increases when the temperature rises, and the strength first increases and then decreases. The number of cycles has little effect on the physical properties of the rock sample; sandstone acoustic emission ringing count increases with the increase of temperature and cycle times, acoustic emission activities become more frequent with the loading process; with the increase of cycle times and temperature, acoustic emission ringing counts and accumulative acoustic emission energy appear earlier The rock sample enters the elastic deformation stage ahead of schedule, the yielding period increases, and the rock sample presents a trend of transition from brittle failure to ductile failure; the ringing count and cumulative energy increase with the increase in temperature and cycle times, and the high-energy ringing count and cumulative energy increase. The simultaneous sharp increase of the rock sample is the harbinger of the failure and instability of the rock sample.

This paper develops a chemical model for a closed constant volume combustion of gaseous mixtures of methane and hydrogen. Since the combustion is strongly depending on temperature, pressure and fuel composition, they were chosen the actual corresponding thermodynamic systems using this kind of combustion, respectively the spark ignition reciprocating engines in order to evaluate the combustion parameters and exhaust flue gases composition. The actual cycles impose extra restrictive operational conditions through the engine volumetric compression ratio, the geometry of combustion volume, the mode to prepare the mixture of methane and hydrogen, the cooling system and the delivered power. The chemical model avoided the unknown influences in order to explain accurately the influence of hydrogen upon the constant volume combustion and flue gases composition. The model adopted simplifying hypotheses, respectively isentropic compression and expansion processes, closed constant volume combustion developed by two successive steps obeying to the energy and mass conservation laws and, flue gases exhaust described also by two steps, i.e. an isentropic expansion through the flow section of exhaust valves followed by a constant pressure stagnation (this succession is corresponding in fact to a throttling direct process). The chemical model supposed the homogeneous mixtures of gases with variable heat capacities function of temperatures, the Mendeleev - Clapeyron ideal gas state equation and, the variable chemical equilibrium constants for chosen chemical reactions. It was assumed that the flue gases chemistry is prevailing during the isentropic expansion and flue gases exhaust and has mainly a thermal ground. The chemical model allowed evaluation of flue gasses composition and of noxious emissions.

The paper presents a three-dimensional slope stability limit equilibrium solution for translational, planar failure modes. The proposed solution uses Bishop’s average skeleton stress combined with the Mohr – Coulomb failure criterion to describe soil strength evolution under unsaturated conditions while its formulation ensures a natural and smooth transition from the unsaturated to the saturated regime and vice versa. The proposed analytical solution is evaluated by comparing its predictions with the results of the Ruedlingen slope failure experiment [1]. The comparison suggests that despite its relative simplicity the analytical solution can capture well the experimentally observed behaviour and highlights the importance of lateral resistance consideration together with a realistic interplay between mechanical parameters (cohesion) and hydraulic (pore water pressure) conditions.

During the extraction of hard coal in Polish conditions, methane is emitted, which is referred to as mine gas. As a result of the desorption of methane, a greenhouse gas is released from coal seams. In order to reduce atmospheric emissions, methane from coal seams is captured by a methane drainage system. On the other hand, methane, which has been separated into underground mining excavations, is discharged into the atmosphere with a stream of ventilation air. For many years, Polish hard coal mines have been capturing methane to ensure the safety of the crew and the continuity of mining operations. As a greenhouse gas, methane has a significant potential, as it is more effective at absorbing and re-emitting radiation than carbon dioxide. The increase in the amount of methane in the atmosphere is a significant factor influencing global warming, however, it is not as strong as the increase in carbon dioxide. Therefore, in Polish mines, the methane-air mixture captured in the methane drainage system is not emitted to the atmosphere, but burned as fuel in systems, including cogeneration systems, to generate electricity, heat and cold. However, in order for such use to be possible, the methane-air mixture must meet appropriate quality and quantity requirements. The article presents an analysis of changes in selected parameters of the captured methane-air mixture from one of the hard coal mines in the Upper Silesian Coal Basin in Poland. The paper analyses the changes in concentration and size of the captured methane stream through the methane capturing system. The gas captured by the methane drainage system, as an energy source, can be used in cogeneration, when the methane concentration is greater than 40%. Considering the variability of CH4 concentration in the captured mixture, it was also indicated which pure methane stream must be added to the gas mixture in order for this gas to be used as a fuel for gas engines. The balance of power of produced electric energy in gas engines is presented. Possible solutions ensuring constant concentration of the captured methane-air mixture are also presented.

Studies on the characteristics of hazardous air pollutants (HAPs) in the emissions of medium-duty diesel trucks are significantly insufficient compared to that on heavy-duty trucks. This study investigates the characteristics of regulated pollutants and HAPs such as volatile organic compounds (VOCs), aldehydes, and polycyclic aromatic hydrocarbons (PAHs), and estimates non-methane hydrocarbon (NMHC) speciation in the emissions of medium-duty diesel trucks. Ten medium-duty diesel trucks conforming to Euros 5 and 6 were tested for worldwide harmonized light duty driving test cycle (WLTC), new European driving cycle (NEDC), constant volume sampler (CVS)-75, and National Institute of Environmental Research (NIER)-9 using a chassis dynamometer. CO and NMHC emissions were the highest in the NEDC because of its longer low-speed driving time. NOx emissions were the highest in WLTC owing to the influence of thermal NOx in the high-speed phase. Alkanes dominated non-methane volatile compound (NMVOC) emissions owing to the low reaction of the diesel oxidation catalyst. After-treatment system, driving, and engine conditions influenced the individual components of NMVOC emissions. Formaldehyde emissions were the highest among aldehydes irrespective of driving cycles. By sampling the particle-phase of PAHs, we detected benzo(k)fluoranthene and benzo(a)pyrene and estimated the concentrations of the gas-phase PAHs with models to obtain the total PAH concentrations. The toxic equivalency quantities of benzo(k)fluoranthene and benzo(a)pyrene from NIER-9 (cold) for both Euro 5 and Euro 6 vehicles were more than five times higher than that of NIER (hot) and NEDC. In the case of NMHC speciation, formaldehyde emissions were the highest in all the driving cycles. Formaldehyde and benzene must be controlled in the emissions of medium-duty diesel trucks to reduce their health threats. The results of this study will aid in establishing a national emission inventory system for HAPs of mobile sources in Korea.

Development of non-conventional hybrids (NCHs) responds to the demand for the Elotes Occidentales 'EO' race for production of pozole. The effect of: crop cycle (2019, 2020 and 2021) on physical characteristics, flowered grain quality and phytochemical content of two HNC (Pz1 and Pz2) of pozolero maize, as well as the effect of the presence or absence of pedicel, type of pollination (open and controlled, 2019), and progenitor lines (female and male, 2020) on flowered grain quality and content of phytochemical compounds were evaluated. Size, hardness, color, total phenols and anthocyanins in unprocessed grain were determined, and yield, volume and puncture strength in flowered grain. Results were analyzed with a factorial arrangement in a completely randomized design. There were significant differences (p≤0.05) in most of the variables studied by effect of crop cycle and genotype. NCHs had large grains (40 g 100 grains-1), soft endosperm (IF&gt; 60), pink-purple color, and phenol and anthocyanin contents similar to those reported for the 'EO' race. The presence or absence of the pedicel did not affect flowered grain quality. Controlled pollination favored anthocyanin synthesis. The anthocyanin content of NCHs was determined by the female line. Thermal processing reduced anthocyanins by 60%; however, they leached into the flowering broth, so that the pozole made from NCHs improves the nutraceutical value of the pozole, relative to that of pozole made with Cacahuacintle maize.

Microbial populations involved in forming the distinctive precipitates of the S, Fe, Mn, and Ca cycles in the San Diego River watershed reflect an interplay between mineralogy of the rocks in the watershed, sparse rainfall, ground- and surface-water anoxia, and runoff of high sulfate, treated imported water. In the less developed headwaters, Temescal Creek tributary emerges from pyrite-bearing metamorphic rocks, and thus exhibits both an oxidized Fe and reduced S cycle. In the middle reaches, the river moves through developed land where treated, imported high sulfate Colorado River water enters from urban runoff. Mast Park surrounded by caliche-bearing sedimentary rocks is a site where marl is precipitating. Cobbles in riffles in the river are coated black with Mn oxide. When the river encounters deep-seated volcanic bedrock, it wells up to precipitate both Fe and Mn oxides at Old Mission Dam. Then, directly flowing through caliche-laced sedimentary rocks, Birchcreek tributary precipitates tufa. Further downstream, at a site that periodically receives full sunlight, a sulfuretum sets up during the summer when the river is deoxygenated. Such a rich geochemistry results in activity of iron and manganese oxidizing bacteria, sulfur oxidizers and reducers, and cyanobacteria precipitating calcareous marl and tufa.

Background: Malaria is one of the most common diseased conditions across most developing countries caused by one of four species of Plasmodium. P. falciparum and P.vivax are the main agents responsible for malaria in Nigeria. Malarial infection has been shown to be associated with abnormalities in fluids, electrolytes and acid base balances. Electrolyte imbalance and mineral disturbances are majorly identified clinical symptoms in various infectious diseases including malaria. Electrolyte imbalance in malarial infection is capable of enhancing disease severity. The aim of this study was to investigate the effects of malarial infection on electrolytes parameters. Methods: Finger prick blood samples, Thick and Thin Giemsa-stained blood smears, were collected from 100 malaria-suspected individuals representing all age groups. The Giemsa-stained blood smears were examined microscopically. Demographic information was obtained using structured questionnaires. The electrolytes levels (Na, K, Cl^- and HCO_3-) in malarial patients were analyzed using standard procedures, Pearson's Correlation Coefficient correlation technique was used to investigate the relationship, and the strength of association between the variables. Results: The mean bound of patients’ sodium level was observed to fall within the specified normal limits of 125mmol/L – 145mmol/L; except for positive malaria patients belonging to the MP-(++) which will fall below the 125mmol/L (i.e. 126.25mmol/L – 1.77mmol/L = 124.48mmol/L). The spread of the sodium data taken from the patients were observed to fall within the normal limits leaving only the boxplot’s lower whisker out, that is, observations falling within the first quartile, except for MP-(++) patients with observations in the first to second quartile spreading outside the normal lower limit, in contrast for the negative tested patients, the box and its whiskers were almost engulfed within the normal limits. Conclusion: In our study we found that Plasmodium falciparum altered more in electrolytes parameters than Plasmodium vivax. The biochemical markers can be used as biomarkers to confirmation of malaria. This study discovered a significant linear relationship based on the Pearson product-moment correlation between creatinine and urea, potassium and chloride, potassium and creatinine, potassium and urea. The mean sodium and chloride level of positive malaria [MP-(++)] patients were observed to fall outside the normal limit.

Under the dual erosion conditions of the dry-wet cycle, which is caused by the high chloride salt concentrations in mine water and fluctuations in mine water level, cemented paste backfill (CPB) suffers serious damage and deterioration. To discuss the mechanical properties and permeability characteristics of CPB under erosion, this study designs an immersion experiment for CPB under chloride salt and dry-wet cycle conditions. Through a uniaxial compressive strength (UCS) test, the change law for the mechanical parameters of the CPB was explored, strength constitutive equation of the CPB was constructed, and the process of deterioration of the CPB was analyzed. Through the penetration test, the diffusion characteristics of packing under chloride salt and dry-wet cycle conditions were explored. The results demonstrated that the strength and elastic modulus of the CPB first increased and then decreased rapidly, with maximum decrease rates of 32.2% and 38.2%, respectively. The CPB structure presents an initial non-damage stage, initial damage stage, damage development stage, damage destruction, and residual damage stage. The chloride ion penetration depth gradually increased with an increase in the number of dry-wet cycles, with a maximum diffusion depth of 20.5 mm. The maximum apparent diffusion coefficient of chloride ion was 18.99×10-10m2/s, and the maximum concentration was 0.303 mol/L. Under the double erosion conditions due to chloride salt and dry-wet cycle, the CPB structure is seriously damaged.

Intrusion detection is generally carried out by matching network traffic patterns with known attack patterns or by identifying abnormal network traffic patterns. One statistical methodological approach used in intrusion detection is Statistical Process Control (SPC) by constructing a control chart. Hotelling’s T2 control chart is a multivariate control chart commonly used to monitor the mean process. The performance of the T2 chart in monitoring mean shifts can be increased if a robust estimator is utilized. Based on previous research, T2 based on the Fast-MCD estimator has good performance in monitoring low to medium outlier contaminated data. Therefore, the MRCD estimator can be used to detect intrusion. On the other hand, this research focuses on developing a bootstrap-based robust Hotelling’s T2 charts with Fast-MCD and MRCD estimators for evaluating performance in detecting intrusion on intrusion detection datasets. Based application of UNSW-NB15, the proposed chart has better performance than the conventional T2 and Fast-MCD-based T2 despite the longer execution time.

Numerous studies have shown that quinolones residues in the foods exceeding the MRL is harmful to the human health. There are some limitations in the existing methods for the residues, so we developed a new limit test method (TLC-SERS) to rapidly determine following residues: enrofloxacin(A), ciprofloxacin (B), ofloxacin(C), fleroxacin(D), sparfloxacin(E), enoxacin(F), gatifloxacin(G) and nadifloxacin(H). The residues can be preliminarily separated by TLC. Labeling the tested compounds’ position on the thin layer plate by their relative Rf under 254nm ultraviolet, and an appropriate amount of nanometer silver solution should be added to the position. The silver on the plate should be irradiated with 532nm laser to obtain SERS of the compounds. The results showed a significant differences of the 8 quinolones’ SERS; the LOD of the H, A, D, E, C, G, F and B were orderly 9.0, 12.6, 8.0, 19.0, 8.0, 8.4, 9.0 and 12.6 ng/mL, and the RSD≤4.9% for SERS of each quinolones.The limit test results of the 20 samples was consistent with that determined by the UPLC–MS/MS. The above results indicate that the TLC-SERS is specific, sensitive, stable, and accurate, providing a new reference for the rapid limit test of harmful residues in foods.

In this work, we treat a prediction problem via the conditional hazard function of a scalar response variable Y given a functional random variable X by using the local linear technique. The main purpose of this paper is to investigate the asymptotic normality of the nonparametric estimator of the conditional hazard function, under some general conditions. A simulation study, conducted to assess finite sample behavior, demonstrates the superiority of our method than the standard kernel method

This study presents a prediction model based on Logistic Growth Curve to evaluate the effectiveness of Movement Control Order (MCO) on COVID-19 pandemic spread. The evaluation assesses and predicts the growth models. The estimated model is a forecast-based model that depended on partial data from the COVID-19 cases in Malaysia. The model is then studied together with the effectiveness of the three phases of MCO implemented in Malaysia. Evidence from this study suggests that results of the LGC prediction model match with the progress and effectiveness of the MCO to flatten the curve, thus helped to control the spike in number of active COVID-19 cases and spread of COVID-19 infection growth.

The central limit theorem (CLT) and its generalization to stable distributions have been widely described in literature. However, many variations of the theorem have been defined and often their applicability in practical situations is not straightforward. In particular, the applicability of the CLT is essential for a derivation of heterogeneous ensemble of Brownian particles (HEBP). Here, we analyze the role of the CLT within the HEBP approach in more detail and derive the conditions under which the existing theorems are valid.

We study the μ-μ45-T phase diagram of the 2+1-dimensional Gross-Neveu model, where μ denotes the ordinary chemical potential, μ45 the chiral chemical potential and T the temperature. We use the mean-field approximation and two different lattice regularizations with naive chiral fermions. An inhomogeneous phase at finite lattice spacing is found for one of the two regularizations. Our results suggest that there is no inhomogeneous phase in the continuum limit. We show that a chiral chemical potential is equivalent to an isospin chemical potential. Thus, all results presented in this work can also be interpreted in the context of isospin imbalance.

This study explores the evolution of price-to-book (P/B) ratios among European banks from 2005 to 2020, period where the majority of banks in different countries had a P/B ratio below 1. By dissecting banks' accounting equity into investor contributions and earnings-derived components, the research aims to evaluate how each component of equity affects these ratios and investigates whether their dynamics shifted during the period. We address a gap in prior research that has not extensively examined how individual equity components affect the overall P/B ratio. This aspect is crucial, especially in scenarios where the increase of specific components compensates for declines in others, thereby stabilizing total equity values. Our methodology involves regression analyses using a panel data model with random effects. The findings reveal that earnings-related equity components significantly influence P/B ratios. In contrast, investor contributions; which strengthen the solvency of the entity, appear to have a minimal impact. Additionally, our analysis highlights a significant quadratic relationship between the P/B ratios and both the profit or loss reported on Income Statements and distributed dividends.

Industrial data scarcity is one of the largest factors holding back the widespread use of machine learning in manufacturing. To overcome this problem, the concept of transfer learning was developed and it achieved high attention in recent industrial research. Our paper focuses on the problem of time series segmentation and presents the first in-depth research about transfer learning for deep-learning based time series segmentation on the example of industrial end-of-line pump testing. In particularly, we investigate if the performance of deep learning models can be increased by pretraining the network with data from other domains. Three different scenarios are analyzed: source and target data being closely related, source and target data being distantly related, and source and target data being non-related. The results demonstrate that transfer learning can enhance the performance of time series segmentation models in respect to accuracy and training speed. The benefit is most clearly seen in scenarios where source and training data are closely related and the number of target training data samples is lowest. However, in the scenario of non-related datasets, cases of negative Transfer Learning were observed as well. Thus, the research emphasizes the potential, but also the challenges of industrial Transfer Learning.

Strong numerical and functional response of owls to voles in cyclic environments is well known, but there is insufficient knowledge from boreonemoral region, in particular, with depleted populations of the small mammals. In this study we describe the dynamics of the small mammal population in Latvia from 1991 to 2016 and link them to owl population characteristics. We used food niche breadth, number of fledglings and population trends to describe the numerical response of six owl species to dampened small mammal population cycles. We found temporarily in-creasing food niche breadth in tawny and Ural owls. There were no other responses in tawny owl, whereas the breeding performance of three forest specialist species – pygmy, Tengmalm`s and Ural owls – were similar to vole crash years in Fennoscandia. Moreover, the populations of forest specialist owls are decreasing and the change in Ural owl can be attributed to the depletion of small mammal populations. We found evidence of carry-over effect in eagle owl arising from strong correlation of declining breeding performance with the small mammal abundance indices in previous autumn. We conclude that dampening of the small mammal population cycles is an important covariate to overwhelming impacts of habitat destruction with stronger response in more specialized (to prey or habitat) species.

Planktonic foraminiferal biomineralization intensity, reflected by their shell calcite mass, affects global carbonate deposition and is known to follow the climate cycles by being increased during glacial stages and decreased during interglacial ones. Here we measure the dissolution state and the mass of the shells of the planktonic foraminifera species Globigerina bulloides from a Tropical Eastern North Atlantic site over the last two glacial-interglacial climatic transitions and we report no major changes in plankton calcite production with the atmospheric pCO2 variations. We attribute this consistency in foraminifera calcification to the climatic and hydrological stability of the tropical regions. We however recorded increased shell masses midway through the penultimate deglaciation (Termination II). In order to elucidate the cause of the increased shell weights we performed δ18O, Mg/Ca and μCT measurements on the same shells from a number of samples surrounding this event. We find that shells of increased mass are internally contaminated by sediment infilling and that shell weights are responding to local hydrographic changes.

Many estuarine ecosystems and the fish communities that inhabit them have undergone substantial changes in the past several decades, largely due to multiple interacting stressors that are often of anthropogenic origin. Few are more impactful than droughts, which are predicted to increase in both frequency and severity with climate change. In this study, we examined over five decades of fish monitoring data from the San Francisco Estuary, California, U.S.A, to evaluate the resistance and resilience of fish communities to disturbance from prolonged drought events. High resistance was defined by the lack of decline in species occurrence from a wet to a subsequent drought period, while high resilience was defined by the increase in species occurrence from a drought to a subsequent wet period. We found some unifying themes connecting the multiple drought events over the fifty-year period. Pelagic fishes consistently declined during droughts (low resistance), but exhibit a considerable amount of resiliency and often rebound in the subsequent wet years. However, full recovery does not occur in all wet years following droughts, leading to permanently lower baseline numbers for some pelagic fishes over time. In contrast, littoral fishes seem to be more resistant to drought and may even increase in occurrence during dry years. Based on the consistent detrimental effects of drought on pelagic fishes within the San Francisco Estuary and the inability of these fish populations to recover in some years, we conclude that freshwater flow remains a crucial but not sufficient management tool for the conservation of estuarine biodiversity.

Solar power innately has issues with weather, grid demand and time of day, which for the case of concentrating solar power (CSP) can be mitigated through use of thermal energy storage. Nuclear reactors, including lead-cooled fast reactors (LFRs), can load follow, but have high fixed and low operating costs which can make this economically unattractive. We investigate potential synergies through coupling CSP and LFR together in a single supercritical CO$_2$ Brayton cycle and/or using the same thermal energy storage. Combining these cycles allows for the LFR to thermally charge the salt storage in the CSP cycle during low demand periods to be dispatched when grid demand increases. The LFR/CSP coupling into one cycle is modeled to find the preferred location of the LFR heat exchanger, CSP heat exchanger, sCO$_2$-to-salt heat exchanger (C2S), turbines, and recuperators within the supercritical CO$_2$ Brayton cycle. Three cycle configurations have been studied: two-cycle configuration, which uses CSP and LFR heat for dedicated turbocompressors, has the highest efficiencies but with less component synergies; a combined cycle with CSP and LFR heat sources in parallel is the simplest with the lowest efficiencies; and a combined cycle with separate high temperature recuperators for both the CSP and LFR is a compromise between efficiency and component synergies. Additionally, four thermal energy storage charging techniques are studied: the turbine positioned before C2S, requiring a high LFR outlet temperature for viability; the turbine after the C2S, reducing turbine inlet temperature and therefore power; the turbine parallel to the C2S producing moderate efficiency; and a dedicated circulator loop. While all configurations have pros and cons, use of a single cycle offers component synergies with limited efficiency penalty. Using a turbine in parallel with the C2S heat exchanger is feasible but results in a low charging efficiency, while a dedicated circulator loop offers flexibility and near perfect heat storage efficiency but increasing cost with additional cycle components.

We study electrohydrodynamic (EHD) linear (in)stability of microfluidic channel flows, i.e. the stability of interface between two-shearing viscous (perfect) dielectrics exposed to an electric field in large aspect ratio microchannels. We then apply our results to particular microfluidic systems known as electroosmotic (EO) pumps. Our results are detailed analytical expressions for the growth rate of two-dimensional EHD modes in Couette-Poiseuille flows in the limit of small Reynolds number ($R$); the expansions to both zeroth- and first-order-$R$ are considered. The growth rates are complicated functions of viscosity-, height-, density- and dielectric-constant ratio, as well as of wavenumbers and voltages, and to our knowledge have not been presented before in literature. To make the results more useful, e.g., for voltage-control EO pump operations, we also derive equations for the impending voltages of the neutral stability curves that divide stable from unstable regions in voltage-wavenumber stability diagrams. The voltage equations and the stability diagrams are given for all wavenumbers. We finally outline the flow regimes in which our first-order-$R$ voltage corrections could potentially be experimentally measured. Our work gives the insight into the coupling mechanism between electric field and shear flow in parallel-planes channel flows, correcting an erroneous attempt from literature. Our general analysis enables us also to refine the renowned instability mechanism due to viscosity stratification, i.e., the case of pure shear instability, when the first-order-$R$ voltage correction equals zero.

We analyze real telematics information for a sample of drivers with usage-based insurance policies. We examine the statistical distribution of distance driven above the posted speed limit – which presents a strong positive asymmetry – using quantile regression models. We find that, at different percentile levels, the distance driven at speeds above the posted limit depends on total distance driven and, more generally, on such factors as the percentages of urban and nighttime driving and on the driver’s gender. However, the impact of these covariates differs according to the percentile level. We stress the importance of understanding telematics information, which should not be limited to simply characterizing average drivers, but can be useful for signaling dangerous driving by predicting quantiles associated with specific driver characteristics. We conclude that the risk of driving long distances above the speed limit is heterogeneous and, moreover, we show that prevention campaigns should target primarily male, non-urban drivers, especially if they present a high percentage of nighttime driving.

The paper outlines a methodology for developing a model to estimate energy consumption in electric vehicles (EVs). The most robust validation indicators were exhibited by an artificial intelligence method, specifically neural networks. Within this framework, two predictive models for EV energy consumption were developed for winter and summer conditions, based on actual driving cycles. Such models hold particular significance for microscale road analyses. The resultant model for test data in summer conditions demonstrates validation indicators with an R2 of 86% and an MSE of 1.4, while for winter conditions, the values are 89% and 2.8, respectively, confirming its high precision. The paper also presents exemplary applications of the developed models, utilizing both real and simulated microscale data. The results obtained and the presented methodology can be especially advantageous for decision-makers in city road management and infrastructure planners, aiding both cognitive understanding and better planning of charging infrastructure networks.

In this work, an evaluation and quantification of the impact of using mixtures based on Supercritical Carbon Dioxide "s-CO2" (s-CO2/COS, s-CO2/H2S, s-CO2/NH3, s-CO2/SO2) are made as a working fluid in simple and complex recompression Brayton s-CO2 power cycles configurations that have pressure drops in their components. These cycles are coupled to a solar thermal plant with parabolic-trough collector (PTC) technology. The methodology used in the calculation performance is to establish values of the heat recuperator total conductance (UAtotal) between 5 and 25 MW/K. The main conclusion of this work is that the cycle's efficiency has improved due to s-CO2 mixtures as working fluid; this is significant compared to that obtained using the standard fluid (pure s-CO2). Furthermore, a techno-economic analysis is carried out that compares each configuration's costs using pure s-CO2 and a mixture of s-CO2/COS with a molar fraction (70/30) respectively as working fluid where relevant results are obtained. These results show that the best configuration in terms of thermal efficiency and cost is the RCC-RH for pure sCO2 with values ​​of 41.25% and 2811 $/kWe, while for the mixture sCO2/COS, the RCC-2RH configuration with values ​​of 45, 05% and 2621 $/kWe is optimal. Using the mixture costs 6.75% less than if it is used the standard fluid (s-CO2).

This study investigated the effects of freeze-thaw cycles on the mechanical properties of hardened self-compacting concrete for varying column heights. A column (100×20×300 cm) was fabricated by C30 self-compacting concrete in the laboratory and 10 cube samples (10x10x10 cm) were taken from fresh concrete as the references. After a period of 28 days, 160 core specimens (Ø67 mm in diameter) were taken from different column heights. Unit weight, water absorption, compressive strength, and freeze-thaw tests were performed on these 170 (10 reference cubic and 160 core) samples. The mechanical properties of the core specimens before freeze-thaw and after 8-56 freeze-thaw cycles were reported for varying column heights. The average compressive strength value of the reference cubic samples was determined as 40.28 MPa, while the compressive strengths of the core specimens before freeze-thaw were ranged from 40.25 MPa to 49.62 MPa, impying an increase in compressive strength values up to 23.18% compared to the reference cubic samples. Compressive strengths of the specimens subjected to 8 and 56 freeze-thaw cycles varied between 38.71‒48.07 MPa and 31.72‒39.11 MPa, respectively. Statistical analysis revealed that the compressive strength of the concrete exposed to 56 freeze-thaw cycles was significantly different from that of the other specimens.

This study investigated the effects of freeze-thaw cycles on the mechanical properties of hardened self-compacting concrete for varying column heights. A column (100×20×300 cm) was fabricated by C30 self-compacting concrete in the laboratory and 10 cube samples (10x10x10 cm) were taken from fresh concrete as the references. After a period of 28 days, 160 core specimens (Ø67 mm in diameter) were taken from different column heights. Unit weight, water absorption, compressive strength, and freeze-thaw tests were performed on these 170 (10 reference cubic and 160 core) samples. The mechanical properties of the core specimens before freeze-thaw and after 8-56 freeze-thaw cycles were reported for varying column heights. The average compressive strength value of the reference cubic samples was determined as 40.28 MPa, while the compressive strengths of the core specimens before freeze-thaw were ranged from 40.25 MPa to 49.62 MPa, impying an increase in compressive strength values up to 23.18% compared to the reference cubic samples. Compressive strengths of the specimens subjected to 8 and 56 freeze-thaw cycles varied between 38.71‒48.07 MPa and 31.72‒39.11 MPa, respectively. Statistical analysis revealed that the compressive strength of the concrete exposed to 56 freeze-thaw cycles was significantly different from that of the other specimens.

The present study evaluates ratcheting response of notched and press-fitted Al 7075-T6 specimens under stress-controlled asymmetric cycles. The degree of interference fit (DIF) directly influenced progressive plastic strain magnitude and rate at notch root region. Local ratcheting at the hole-pin interference region was analyzed by means of two kinematic hardening rules of Ahmadzadeh-Varvani (A-V) and Chaboche coupled with the Neuber rule. Ratcheting strains at notch root of aluminum samples with DIF=0 (non-press-fitting samples) were measured to be highest in magnitude. For the press-fitted samples, however ratcheting strains dropped noticeably as DIF increased from 1% to 2%. Press-fitted samples plastically deformed the perimeter edge of notches and improved materials locally at the notch edge, resulting in a better resistance against ratcheting progress. Local ratcheting at different distances of 0.5, 1.3 and 3.0 mm from the notch root were evaluated for both pinned and unpinned samples through the hardening rules and compared with those of measured values. The predicted ratcheting curves by means of the A-V and Chaboche hardening rules closely agreed with experimental data and respectively positioned above and below the measured data.

We prove through path integral Monte Carlo computer experiments that the affine quantization of the $\varphi_4^4$ scaled Euclidean covariant relativistic scalar field theory is a valid quantum field theory with a well defined continuum limit of the one- and two-point-function. Affine quantization leads to a completely satisfactory quantization of field theories using situations that involve scaled behavior leading to an unexpected, $\hbar^2/\varphi^2$ which arises only in the quantum aspects.

A quantitative description of the second law of thermodynamics in small scale systems and over short time scales comes from various fluctuation theorems. The applicability of the transient fluctuation theorem in particular to small scale systems perturbed from an initial equilibrium steady-state distribution has been demonstrated both theoretically and experimentally in several works over the past few decades. In addition, some experimental works in the past have also made successful attempts to demonstrate the applicability of the fluctuation theorem to small scale systems evolving from a certain nonequilibrium steady-state distribution over relatively long time scales. To this end, this paper seeks to demonstrate the transient fluctuation theorem for a Brownian particle confined within a power-law trapping potential by following the trajectory of the particle that itself is translating linearly along one dimension with constant acceleration in a viscous fluid. Considered herein is an idealized version of this model, in that it is assumed that the force of the trapping potential is only felt by the translating Brownian particle confined within the trap, and that this Brownian particle moves relative to the fluid molecules that are held stationary. The results presented herein show that the transient fluctuation theorem applies not only to equilibrium steady-state distributions but also to nonequilibrium steady-state distributions of an ideal colloidal system in an accelerated frame of reference in the asymptotic (long-time) limit.

Noise induces oxidative stress in the cochlea followed by sensory cell death and hearing loss. The proof of principle that injections of antioxidant vitamins and Mg²⁺ prevent noise-induced hearing loss (NIHL) has been established. However, effectiveness of oral administration remains controversial and otoprotection mechanisms unclear. Using auditory evoked potentials, quantitative PCR and immunocytochemistry, we explored effects of oral administration of vitamins A, C, E and Mg²⁺ (ACEMg) on auditory function and sensory cell survival following NIHL in rats. Oral ACEMg reduced auditory thresholds shifts after NIHL. Improved auditory function correlated with increased survival of sensory outer hair cells. In parallel, oral ACEMg modulated the expression timeline of antioxidant enzymes in the cochlea after NIHL. There was increased expression of Glutathione peroxidase-1 and Catalase at 1 and 10 days, respectively. Also, pro-apoptotic Caspase-3 and Bax levels were diminished in ACEMg-treated rats, at 10 and 30 days, respectively, following noise overstimulation, whereas, at day 10 after noise exposure, the levels of anti-apoptotic Bcl-2, were significantly increased. Therefore, oral ACEMg improves auditory function by limiting sensory hair cell death in the auditory receptor following NIHL. Regulation of the expression of antioxidant enzymes and apoptosis-related proteins in cochlear structures is involved in such otoprotective mechanism.

Sulfate attack is one of the main factors affecting the durability of concrete structures. In recent years, multi-walled carbon nanotubes (MWCNTs) have attracted the attention of scholars for their excellent mechanical properties and durability performance. In this paper, the influence of sulfate attack and dry-wet cycles on the performance of multi-walled carbon nanotube-lithium slag concrete (MWCNTs-LSC) with varied MWCNTs content (0wt%, 0.05wt%, 0.10wt% and 0.15wt%) and varied water-cement ratios (0.35, 0.40 and 0.45) were investigated. Besides, scanning electron microscopy (SEM) and X-ray computed tomography (CT) tests were conducted to analyze the microstructure and pore structure of the concrete. The results show that concrete incorporated with MWCNTs could effectively mitigate sulfate attack The resistance to sulfate attack of concrete is negatively related to the water-cement ratio when the dry-wet cycle is fixed. The MWCNTs-LSC showed the best compressive strength at the water-cement ratio of 0.35 and 0.10 wt% MWCNTs. The SEM test results showed that the MWCNTs both filled the pores and cracks within the specimen and formed bridges between the cracks, enhancing the resistance to sulfate attack. The CT test results also showed that the addition of MWCNTs could reduce the porosity of concrete, refine the pore size and inhibit the generation and development of cracks, thus optimizing the internal structure of concrete and improving its resistance to sulfate attack.

Salmon farming has been blamed for the collapse of the sea trout (Salmo trutta) fishery in Loch Maree on Scotland’s west coast despite the absence of any direct evidence. Stocks of west coast demersal marine fish, especially around the Clyde Estuary have also declined over a similar time span. The decline of these marine fish stocks can be attributed to the removal of the “three-mile fishing limit” in 1984 by UK Government legislation. Sea trout inhabit the same inshore waters as targeted demersal fish and can be caught as by-catch. Comparisons of the decline of demersal species and the sea trout from Loch Maree and the west coast show a high degree of correlation. Stocks of whiting (Merlangius merlangus) from inshore waters have found to consist of small fish which mirrors the stock makeup of the Loch Maree sea trout stock.

In order to study the burrowing crab Neohelice granulata (Dana, 1851) in the northern limit of its distribution and to test the hypothesis that mesoscale factors are more deterministic than latitudinal variation in this crab life history, the population dynamics of this specie was studied in the Caceribú river (Rio de Janeiro state, Brazil). The sex ratio was female-biased over the year. Males were significantly larger (t-test = 3.53, p < 0.05) than females (CW mean = 29.14 mm and 27.32 mm, respectively), which were predominant in the intermediary-size classes. The breading season took place from February to November, with a peak in May. The recruitment was observed all over the year, but mostly from October to December. The size at maturity was estimated at 19.0 mm for females and 23.9 mm for males. Average fecundity was 20,419 eggs (±12,627.12) and showed a decrease from the first to the last stage of embryonic development. The asymptotic size was similar between males (CW∞ = 24.86 mm) and females (CW∞ = 24.50 mm). Longevity was estimated in 1.33 and 1.23 years in males and females, respectively. Mortality rates were slightly higher in males (Z = 3.71) than in females (Z 0 3.41). Analysing the results of this study and the literature we conclude that the population dynamics of N. granulata do not follow a latitudinal trend. This strengthens the hypothesis that brachyurans’ life histories are mainly driven by mesoscales factors than latitudinal variation.

A multi-strand composite welding wire was applied to join high nitrogen austenitic stainless steel, and microstructures and mechanical properties were investigated. The electrical signals demonstrate that the welding process using a multi-strand composite welding wire is highly stable. The welded joints are composed of columnar austenite and dendritic ferrite and welded joints obtained under high heat input and cooling rate have a noticeable coarse-grained heat-affected zone and larger columnar austenite in weld seam. Compared with welded joints obtained under the high heat input and cooling rate, welded joints have the higher fractions of deformed grains, high angle grain boundaries, Schmid factor and the lower dislocation density under the low heat input and cooling rate, which indicate a lower tensile strength and higher yield strength. The rotated goss (G_RD) orientation of a thin plate and the cube (C) orientation of a thick plate are obvious after welding, but the S orientation at 65° sections of Euler’s space is weak. The δ-ferrite was studied based on the primary ferrite solidification mode. It is observed that low heat input and high cooing rate result in the increasing of δ-ferrite and high dislocation density was obtained in grain boundaries of δ-ferrite. M₂₃C₆ precipitates due to low cooling rate and heat input in weld seam and deteriorates the elongation of welded joints. The engineering stress-strain curves also show the low elongation and tensile strength of welded joints under low heat input and cooling rate, which is mainly caused by the high fraction of δ-ferrite and the precipitation of M₂₃C₆.

Low-cost particle sensors are now used worldwide to monitor outdoor air quality. However, they have only been in wide use for a few years. Are they reliable? Does their performance deteriorate over time? Are the algorithms for calculating PM2.5 provided by the Plantower company for PurpleAir monitors accurate? We investigate these questions using continuous measurements of four monitors (8 sensors) under normal conditions inside and outside a home for 1.5-3 years. A recently-developed algorithm (called ALT-CF3) is compared to the two existing Plantower algorithms. The Plantower CF1 algorithm was shown to lose 25-50% of all indoor data due to the questionable practice of assigning zero to all concentrations below a threshold. None of these data were lost using the ALT-CF3 algorithm. About 92% of all data showed precision better than 20% using the ALT-CF3 algorithm, but only about 45-75% of data achieved that level using the Plantower CF1 algorithm. The limits of detection (LODs) using the ALT-CF3 algorithm were mostly under 1 ug/m3, compared to about 3-10 ug/m3 using the Plantower CF1 algorithm. The percent of observations exceeding the LOD was 53-92% for the ALT-CF3 algorithm, but only 16-44% for the Plantower CF1 algorithm. For indoor air in homes, the Plantower algorithms are inappropriate.

Earth’s extinction crisis is escalating, and threat classification schemes are increasingly important for assessing which human activities are the most prominent drivers of species declines. However, a quantitative understanding of the conservation responses needed to abate threatening processes, and avoid species extinctions, is often lacking. Here, we provide a threat abatement framework which groups threats based on the shared conservation goal of the actions needed to abate their impact. We apply this framework to Australia’s threatened species to quantify the relative importance of achieving different conservation response goals. Our analysis shows the most important conservation responses across Australia are habitat retention and restoration, due to the combined impact of threatening processes causing habitat destruction and degradation (e.g. logging, mining, urbanisation and agriculture), which affects the majority (86%) of Australia’s threatened species and the effective control of invasive species (82%). Most species also require conservation responses focussed on improved fire management (66%). We show that implementing responses in isolation will be inadequate for abating species extinctions as almost all species (89%) require multiple, integrated management responses to redress their threats. We also acknowledge that already small and potentially genetically compromised taxa may require more direct interventions (e.g. captive insurance populations or genetic rescue). Our analysis highlights the necessity of addressing multiple threats at appropriate geographic scales across Australia. Our threat abatement framework ensures that core conservation actions can be identified and aid recovery of threatened species, and can be applied to other geographic regions and conservation contexts.

The ability to predict the likelihood of a live birth after single fresh embryo transfer is important for treatment planning and managing patient expectation, particularly in their first in vitro fertilization (IVF) cycle. Cryopreservation of supernumerary embryos is often regarded as an important prognostic variable and a surrogate marker of success for several reasons. While previous large studies have examined the association between the number of oocytes retrieved and cleavage-stage embryos available, and the odds of a live birth following a fresh embryo transfer, the relationship between the number of supernumerary blastocysts cryopreserved following a fresh embryo transfer has not been rigorously studied. We performed a retrospective analysis of data collected between 2006 and 2018 for all first time IVF patients with a fresh autologous day 5 single blastocyst transfer. The relationship between the likelihood of a live birth and number of supernumerary blastocysts cryopreserved was assessed according to patient age group. In patients aged <35 years and 35-39 years old, the likelihood of a live birth increased linearly from 0.33 (95%CI:0.31–0.34) to 0.80 (95%CI:0.74–0.86; P<.0001) and 0.30 (95%CI:0.28–0.32) to 0.82 (95%CI:0.73–0.91;P<.0001) between 1-6 blastocysts cryopreserved and then non-linearly to 0.95 (95% CI 0.92–0.97; P<.0001) and 0.96 (95%CI:0.93–0.99; P<.0001) if 10 or more blastocysts were cryopreserved, respectively. When aged 40 years and above, the likelihood of a live birth increased linearly from 0.26 (95%CI:0.19–0.32) to 0.83 (95%CI:0.68–0.97; P<.0001) between 1-4 blastocysts cryopreserved and then non-linearly to 0.99 (95%CI:0.98–0.99; P<.0001) if 10 or more blastocysts were cryopreserved. The present study demonstrated a non-linear relationship between the number of supernumerary blastocysts cryopreserved and the likelihood of a live birth after single blastocyst transfer in the first autologous fresh IVF/ICSI cycle across different age groups.

HIV-1 is a complicated and perplexing virus. It infects T cells, reverse transcribes its RNA into DNA, utilizes its host DNA machinery to replicate its HIV-DNA, translates the HIV-DNA into proteins, assembles itself for a budding escape from the T cell, and rapidly mutates its conformation. Partially, due to its complexity, there remains no cure for HIV or AIDs. However, recently with the discovery of TALENs, the use of zinc fingers, and most of all the applications of CRISPR-Cas9 technology, has given researchers new hope in finding alternative gene therapies and treatments for diseases. With more focus on CRISPR-Cas9, this new and novel technology uses a guiding RNA, sgRNA, to lead a Cas9 nuclease to its target for deletion or to change that DNA site. CRISPR-Cas9 can delete point mutations and multiple DNA sites. Because CRISPR can alter DNA sequences, several scientists have conducted research into CRISPR, possibly treating more diseases such as cancer, diabetes, and even HIV. HIV-1 drew the focus of a researcher named Dr. Ebina in 2013 when he was the first to design and apply CRISPR-Cas9 to genes found in the binding sites of HIV-1, inhibiting HIV-1 gene expression. Since 2013, several other researchers have blocked HIV replication and infection through CRISPR-Cas9 targeting the receptors of T cells called the CC chemokine receptor 5 or CCR5. HIV-1 binds to the CD4 receptor of T cells, which consists of co-receptors CCR5 and CXCR4. If CCR5 expression can be removed, the HIV virus cannot bind to T-cells, blocking the initial attachment stage, and discontinuing the infection. However, there remain obstacles and issues for the CRISPR deletion of CCR5 for treating HIV-1. The issues include: 1) finding new and safe methods of CRISPR-Cas9 delivery, 2) clearing the latent HIV reservoirs, 3) improving the sgRNA design to avoid off-target mutations or deletions, and 4) effectively analyze the viral escape of HIV from CRISPR-Cas9 modifications. Therefore, the purpose of this review is to discuss possible techniques for removing the obstacles that can lessen the potential of CRISPR to delete CCR5, repressing HIV-1 into long-term remission or a functional cure.

During middle age, women are less susceptible to nonalcoholic steatohepatitis (NASH) than men. Thus, we investigated the underlying molecular mechanisms behind these sexual differences using an established rat model of NASH. Mature female and male stroke-prone spontaneously hypertensive 5/Dmcr rats were fed control or high-fat-cholesterol (HFC) diets for 2, 8, and 14 weeks. Although HFC-induced hepatic fibrosis was markedly less severe in females than in males, only minor gender differences were observed in expression levels of cytochrome P450 enzymes (CYP)7A1, CYP8B1 CYP27A1, and CYP7B1, and multidrug resistance-associated protein 3, and bile salt export pump, which are involved in fibrosis-related bile acid (BA) kinetics. However, the BA detoxification-related enzymes UDP-glucuronosyltransferase (UGT) and sulfotransferase (SULT) 2A1, and the nuclear receptors constitutive androstene receptor (CAR) and pregnane X receptor (PXR), were strongly suppressed in HFC fed males, and were only slightly changed in HFC-diet fed females. Expression levels of the farnesoid X receptor and its small heterodimer partner were similarly regulated in a gender-dependent fashion following HFC feeding. Hence, the pronounced female resistance to HFC-induced liver damage likely reflects sustained expression of the nuclear receptors CAR and PXR and the BA detoxification enzymes UGT and SULT.

The Simulation analogy presented in this work enhances the accessibility of abstract quantum theories, specifically the stochastic hydrodyanimc model (SQHM), by relating them to our daily experiences. The SQHM incorporates the influence of fluctuating gravitational background, resembling dark energy, into quantum equations. This model successfully addresses key aspects of Objective-Collapse Theories, including resolving the 'tails' problem through the definition of quantum potential length in addition to the De Broglie length, beyond which coherent Schrödinger quantum behavior and wavefunction tails cannot be maintained. The SQHM emphasizes that an external environment is unnecessary, asserting that the quantum stochastic behavior leading to wave-function collapse can be an inherent property of a system in a spacetime with fluctuating metrics. Embedded in relativistic quantum mechanics, the theory establishes a coherent link between the uncertainty principle and the constancy of light speed, aligning seamlessly with finite information transmission speed. Within a fluctuating quantum system, the SQHM derives the indeterminacy relation between energy and time, offering insights into measurement processes impossible within a finite time interval in a truly quantum global system. Experimental validation is found in confirming the Lindemann constant for solid lattice melting points and the transition from fluid to superfluid states. The SQHM's self-consistency lies in its ability to describe wavefunction collapse and the measure process. Additionally, the theory resolves the Pre-existing Reality problem by showing that large-scale systems naturally decay into decoherent states stable in time. Continuing, the paper demonstrates that the physical dynamics of SQHM can be analogized to a computer simulation employing optimization procedures for realization. This perspective elucidates the concept of time in contemporary reality and enriches our comprehension of free will. The overall framework introduces an irreversible process impacting the manifestation of macroscopic reality at the present time, asserting that the multiverse exists solely in future states, with the past comprising the formed universe after the current moment. Decoherence at the present time functions as a reduction of the multiverse to a single universe. The macroscopic reality, characterized by fractal consistency where microscopic domains with quantum properties coexist, provides insights into how our consciousness apprehends dynamic reality, the spontaneous emergence of gravity in discrete spacetime evolution, and the attainment of the classical General Relativity limit in Quantum Loop Gravity and Causal Dynamical Triangulation. The Simulation Analogy highlights a strategy focused on minimizing information processing, facilitating the universal simulation in solving its predetermined problem. From within, reality becomes the manifestation of specific physical laws emerging from the inherent structure of the simulation devised to address its particular issue. In this context, the reality simulation appears to employ an entropic optimization strategy, minimizing information loss while efficiently compressing data in line with the simulation's intended purpose.

Hazardous toxic metals, such as lead and cadmium, and to a lesser extent aluminum, are extensively recognized as detrimental for health following ingestion within food and water, or following inhalation. Gut and food-derived microbes, by interacting with heavy metals, may actively or passively modulate their bioavailability inside the gut, either by adsorption or by sequestration. Such a bioremediation within the gut implies the selection of safe microbes, based on their specific capacities to immobilize metals. We investigated the metal removal ability of 225 bacteria toward the potential harmful trace elements lead, cadmium and aluminum in vitro, using Inductively Coupled Plasma Mass Spectrometry analysis. Interspecies and intraspecies comparisons were addressed and discussed among bacteria from the phylum Firmicutes, which are mostly lactic acid bacteria, including Lactobacillus spp, with some Lactococcus, Pediococcus and Carnobacterium representatives, Actinobacteria as well as Proteobacteria. The effect on mixture of lead and cadmium was also investigated. Although the purpose of such a screening is so far not to elucidate each of the various strain specific- and metal dependent- mechanisms of heavy metal removal, we identified potential bacteria which are able to alleviate Pb(II) and Cd(II) concerns in order to propose performing candidate probiotics for metal xenobiotic bioremediation.

Despite a significant number of investigations in the field of phosphazene chemistry, the mechanism of this class cyclic compounds formation is still poorly studied. At the same time, a thorough understanding of this process is necessary both for the direct production of phosphazene rings with a given size, and for the controlled cyclization reaction when it is secondary and undesirable. Here we have synthesized a series of short linear phosphazene oligomers with the general formula Cl[PCl2=N]n–PCl3+PCl6– and studied their tendency to form cyclic structures under the influence of elevated temperature or in the presence of nitrogen-containing agents, such as hexamethyldisilazane (HMDS) or ammonium chloride. It was established that linear oligophosphazenes are inert when heated in the absence of the mentioned cyclization agents, and the formation of cyclic products occurs only when these agents are involved in the process. It is for the first time shown the ability to obtain the desired size phosphazene cycle from corresponding linear chain. Known obstacles like side interaction with the PCl6– counterion and a tendency of longer chains to undergo crosslinking elongation instead of cyclization are still relevant and ways to overcome them are being discussed.

Milk serves as a crucial source of natural bioactive compounds essential for human nutrition and health. The gastrointestinal digestion of milk proteins releases various biologically active peptides that positively impact human health and enhance physiological performance. With the growing production of cheese, Greek yogurt, and other dairy products, the volume of unutilized acid whey is significantly increasing. Acid whey, containing almost all whey proteins and approximately one-quarter of casein, presents a valuable raw material for generating peptides with potential health benefits. These peptides exhibit properties such as antioxidant, antimicrobial, anti-inflammatory, anticarcinogenic, antihypertensive, antithrombotic, opioid, mineral-binding, and growth-stimulating activities, contributing to improved human immunity and the treatment of chronic diseases. Enzymatic hydrolysis of milk proteins has been developed as a method to produce these peptides, facilitating their use in food fortification. To incorporate whey into functional beverages, it undergoes fermentation by lactic acid bacteria with proteolytic activity. To specifically enrich these beverages with peptides exhibiting targeted bioactivities, it is essential to select lactic acid bacteria strains possessing the requisite protease profiles. Additionally, the sensory properties of the final product can be enhanced using starter cultures with diverse metabolic capabilities, even in the absence of added flavoring agents. Given the imperative to develop waste-free technologies and enhance the profitability of the dairy industry, there is a growing need to efficiently utilize and transform acid whey into a broad spectrum of valuable products and food additives. This approach is justified not only by the nutritional benefits of the bioactive components in whey but also by the commercial potential of safe and health-enhancing products.

The paper focuses on the application of a multilevel, integrative and territorial approach to the protection of cultural heritage through planning instruments in Serbia. It points out the problems of the sectoral approach and discusses international recommendations that can be integrated into the planning methodology. The case study is the area of Djerdap National Park, which has an already established international and national importance. The research suggests that the cultural heritage in the area, with the exception of the Roman limes, is still recognized at the level of individual localities. The study emphasizes the importance of aligning all levels of governance to safeguard the whole spatial entity rather than focusing solely on its particular areas. The interna-tional and national importance of the planning area contributes to the strengthening of awareness of heritage and its institutional protection. However, the vitality of the area, which is key to its sustainable development, comes from the local level. Planning documents contribute to the inte-gration of local values and local communities into development programs and projects.