In this paper, the time-resolved model of photoacoustic signal for samples with a complex inner structure is derived including local non-equilibrium of structural elements with multiple degrees of freedom, i.e. structural entropy of the system. The local non-equilibrium is taken into account through the fractional operator. By analyzing the model for two types of time-dependent excitation, a very short pulse and a very long pulse, it is shown that the rates of non-equilibrium relaxations in complex samples can be measured by applying the derived model and time-domain measurements. Limitations of the model and further directions of its development are discussed.

The design complexity of the new generation of civil aero-engines results in higher demands on engines’ components, higher component temperature, higher heat generation, and, finally, critical thermal management issues. This paper will propose a methodological approach to create physics-based models for heat loads developed by sources as well as a systematic sensitivity analysis to identify the effects of design parameters on the thermal behaviour of civil aero-engines. The ranges and levels of heat loads generated by heat sources (e.g., accessory gearbox, bearing, pumps, etc.) and heat absorption capacity of heat sinks (e.g., engine fuel, oil, and air) are discussed systematically. The practical research challenges for thermal management system design and development for the new and next generation of turbofan engines will then be addressed through a sensitivity analysis of the heat load values as well as the heat sinks flow rates. The potential solutions for thermal performance enhancements of propulsion systems will be proposed and discussed accordingly.

Coal gasification with carbon dioxide is a process for generating clean gaseous fuels and relieving greenhouse effect. Zhundong coal has high alkali and alkali earth metals (AAEMs) content, medium volatile and low ash in nature. Isothermal CO₂ gasification of char derived from Zhundong coal (R-char) and char from acid washing R-char (AR-char) are performed in thermo-gravimetric analyzer (TGA). The effect of AAEMs is investigated on the gasification behavior in the range of temperatures 1073 K to 1273 K. The carbon conversion increases rapidly with increasing reaction temperature and CO₂ concentration. R-char has high gasification rate and carbon conversion compared with AR-char. The accuracy of the free-model approach for calculating activation energy at different conversions is validated by compared with different kinetic models (volume reaction model, distributed activation energy model). Moreover, R-char gasification with CO₂ shows a compensation effect as the Arrhenius parameters (EA and k0) increase or decrease simultaneously.

Ménière's disease (MD) has an unclear cause. The microvascular dysregulation of the inner ear has been increasingly pointed as a potential contributor. This study investigates the prevalence of cardiovascular risk factors (CVRFs) in MD patients compared to those with posterior circulation cerebral infarction (POCI). CVRFs like hypertension, diabetes, dyslipidemia, obesity, coronary heart disease, and smoking were assessed in both MD and POCI patients. Brain MRI identified POCI etiology as "small vessel occlusion" (SVO) or "other etiology" (OE). The study included 64 MD and 84 POCI patients. Compared to MD, POCI OE showed a higher prevalence of CVRFs across various age groups, including hypertension, diabetes, dyslipidemia, and smoking. Notably, the odds of having POCI OE were significantly higher for individuals with hypertension and smoking. On the other hand, POCI SVO showed similar prevalence of CVRFs compared to MD. This study reveals no significant difference in CVRF prevalence between MD and smaller vessel POCI. However, a clear distinction emerges when comparing MD to POCI with involvement of larger blood vessels. Further research is needed to confirm these findings and explore potential shared risk factors between POCI (SVO) and MD.

Three kinds of inorganic alkali are introduced into tetraethylenepentamine (TPEA) and polyethyleneimine (PEI) modified MCM-41 as the CO2 adsorbents. FT-IR and TGA are used to characterize the surface groups and the thermal stability of adsorbents. Chemical titration method is used to measure the alkali amounts of adsorbents. Thermo-gravimetric analysis with 10%CO2/N2 as the simulated flue gas is used to test the CO2 adsorption performance of adsorbents. The results show that all three kinds of inorganic alkali containing adsorbents exhibit promoted CO2 adsorption capability than traditional TPEA and PEI modified samples. Ca(OH)2 and PEI modified samples exhibit the highest adsorption capacity and stable regeneration property. The introduction of inorganic alkali changes the chemical adsorption mechanism between CO2 and increases the effective alkali amounts due to its hydroxyl groups. The CO2 adsorption capacities have a linear dependence relation with the alkali amounts of adsorbents, indicating that alkali amount is a critical factor for novel adsorbents exploring.

The European Green Deal poses a two-pronged challenge for the automotive industry: migrating to solutions based in light structures, requiring light weight concepts and light materials, while at the same time avoiding dependence towards the importation of these advanced materials. Aluminium alloys are lightweight and cost-effective materials that can successfully cover the requirements of many structural applications, however their production requires from bauxite and other Critical Raw Materials (CRM), such as Si and Mg. Aluminium alloys are fully recyclable, but scrap is usually contaminated and its use is related to an increment of impurities, tramp element and undesired inclusions. Traditionally, the use of secondary alloys has been restricted to low performance applications. The present work analyses the effect that the use of scrap has in the quantity of inclusions present in the alloy and in other properties relevant for the material processing. The study was carried out for common alloys belonging to 3 of the most common aluminium processes used in the car manufacturing industry: High Pressure Die Casting (HPDC) (EN AC-43500), extrusion (6063) and sheet metal forming (5754 and 6181). Reference alloy were mixed with different level of scrap (0, 20, 40, 60, 80 and 100%) trying to keep the chemical composition as unaffected as possible. The inclusions level of the alloy was characterized with the Prefil Foot-printer® test. In addition, the obtained materials, after being cast in an open mould, were subjected to metallographic characterization. Relevant properties to assess the formability quality of the alloys for the corresponding transforming process, were obtained: flowability test for HPDC alloy and high temperature compression for extrusion alloys. The results obtained suggest that the number of inclusions present in the melt highly increase with the amount of scrap used to produce the alloy. These inclusions are also related with an important lost of flowability, but do not have a noticeable impact on microstructure.

There exists a great potential for application in soil mechanics with the use of mechanistic models such as the finite element model, and other non-local models, such as the peridynamic model, since the soil mass can be modelled as a group of particles that interact with each other. In this work, we determine the bearing capacity of deep foundations where stresses are transmitted to deep deposits, which generally present better characteristics in terms of compressibility and shear strength. One of the main elements are driven piles, which must be previously designed, made and tested before their final use. In this work, a comparison with different methods is presented. The finite element method and the peridynamic model are used. Because the effect of consolidation was not taken into account, in these examples, the assumption is made that the structures are cemented in inert soil. Likewise, it is assumed that the water table has no influence on the simulations. Failure envelopes were observed where bonds between particles present high gradients of deformation and fracture. Bearing capacities were estimated and compared with those obtained from the Terzaghi and Meyerhof methods.

The paper presents a proposal for an in-house mathematical model of a liquid flat-plate solar collector. The proposed model is a one-dimensional distributed parameter model enabling simulations of the collector operation under arbitrarily variable boundary conditions. The model is based on the solution of energy balance equations for all components of the collector. The formulated differential equations are solved iteratively using an implicit difference scheme. In order to obtain a stable numerical solution, it is necessary to use appropriate steps of the time and spatial division. These were found by comparing the results obtained from the model with the results of the analytical solution available in the literature for the transient state, which constitutes the novelty of the present study. The accuracy of the results obtained from the model was verified experimentally by comparing the measured and the calculated history of the fluid temperature at the outlet of the collector. The calculation of the collector time constant is proposed in the paper as an example of the model practical application. The results of the time constant calculation were compared with the values obtained experimentally on the test stand. This is another novelty of the presented research. The analysed collector instantaneous efficiency was then calculated for selected outdoor conditions. The presented mathematical model can also be used to verify the correctness of the collector operation. Comparing, on an ongoing basis, the measured and the calculated values of the fluid temperature at the collector outlet, conclusions can be drawn about the process of solar glass fouling or glycol gelling. The model's simplicity and the low computational demands enable such comparisons in an online mode.

The quiet-time solar wind electrons feature non-thermal characteristics when viewed from the perspective of their velocity distribution functions. They typically have an appearance of being composed of a denser thermal “core” population plus a tenuous energetic “halo” population. At first, such a feature was empirically fitted with the Kappa velocity space distribution function, but ever since the ground-breaking work by Tsallis, the space physics community has embraced the potential implication of the Kappa distribution as reflecting the non-extensive nature of the space plasma. From the viewpoint of microscopic plasma theory, the formation of non-thermal electron velocity distribution function can be interpreted in terms of the plasma being in a state of turbulent quasi equilibrium. Such a finding brings forth the possible existence of a profound inter-relationship between the non-extensive statistical state and the turbulent quasi-equilibrium state. The present paper further develops the idea of solar wind electrons being in the turbulent equilibrium, but unlike the previous model, which involves the electrostatic turbulence near the plasma oscillation frequency (i.e., Langmuir turbulence), the present paper considers the impact of transverse electromagnetic turbulence, particularly, the turbulence in the whistler-mode frequency range. It is found that the coupling of spontaneously-emitted thermal fluctuations and the background turbulence leads to the formation of non-thermal electron velocity distribution function of the type observed in the solar wind during quiet times. This demonstrates that the whistler-range turbulence represents an alternative mechanism for producing the Kappa-like non-thermal distribution, especially close to the Sun and in the near-Earth space environment.

Extreme heat is a climate hazard that has been linked with high morbidity and mortality. The way extreme heat events are felt in the population varies depending on a variety of factors, such as age, employment status, living conditions, air-conditioning, housing conditions, habits, behaviors, and other socio-demographic parameters. To quantify and locate vulnerabilities of populations to extreme heat, we analyze socio-economic data at the NUTS3 level for the national case study of Greece and at the census tract level for the local case study of the city of Athens. The target variable for this study is defined as the average daily mortality during heatwaves per 100,000 individuals and a methodology is developed for constructing this variable, based on socio-economic data available in public databases. Independent variables were selected based on their contribution to socioeconomic vulnerability; they include the percentage of elderly, retired, unemployed, renting, living alone, residing in smaller houses, living in older houses, and immigrants from developing countries. An ensemble gradient boosted tree model was employed for this study to obtain feature importance metrics that was used to construct a composite index of socioeconomic heat vulnerability. The socioeconomic heat vulnerability index (SHVI) was calculated for each prefecture in Greece and for each census tract in the city of Athens, Greece. The unique feature of this SHVI is that it can be applied to any geographical resolution using the same methodology and produces a result that is not only quantifiable, but also allows comparison between vulnerability scores of different regions. This application aimed to map the SHVI of both prefecture and city, to examine the significance of scale, to identify vulnerability hotspots, and rank the most vulnerable areas, which are prioritized by authorities for interventions that protect public health.

Numerical models widely used for hydrocarbon phase behavior and compositional flow simulations are based on assumption of thermodynamic equilibrium. However, it is not uncommon for oil and gas-condensate reservoirs to exhibit essentially non-equilibrium phase behavior, e.g., in the processes of secondary recovery after pressure depletion below saturation pressure, or during gas injection, or for condensate evaporation at low pressures. In many cases the ability to match field data with equilibrium model depends on simulation scale. The only method to account for non-equilibrium phase behavior adopted by the majority of flow simulators is the option of limited rate of gas dissolution (condensate evaporation) in black oil models. For compositional simulations no practical yet thermodynamically consistent method has been presented so far except for some upscaling techniques in gas injection problems. Previously reported academic non-equilibrium formulations have a common drawback of doubling the number of flow equations and unknowns compared to the equilibrium formulation. In the paper a unified thermodynamically-consistent formulation for compositional flow simulations with non-equilibrium phase behavior model is presented. Same formulation and a special scale-up technique can be used for upscaling of an equilibrium or non-equilibrium model to a coarse-scale non-equilibrium model. A number of test cases for real oil and gas-condensate mixtures are given. Model implementation specifics in a flow simulator are discussed and illustrated with test simulations. A non-equilibrium constant volume depletion algorithm is presented to simulate condensate recovery at low pressures in gas-condensate reservoirs. Results of satisfactory model matching to field data are reported and discussed.

There is little doubt that life's origin followed from the known physical and chemical laws of Nature. The most general scientific framework incorporating the laws of Nature and applicable to most known processes to good approximation, is that of thermodynamics and its extensions to treat out-of-equilibrium phenomena. The event of the origin of life should therefore also be amenable to such an analysis. In this paper, I describe the non-equilibrium thermodynamic foundations of the origin of life for the non-expert. This ``Thermodynamic Dissipation Theory for the Origin of Life'' is founded on Classical Irreversible Thermodynamic theory developed by Lars Onsager, Ilya Prigogine, and coworkers.

Meixner's historical remark in 1969 "... it can be shown that the concept of entropy in the absence of equilibrium is in fact not only questionable but that it cannot even be defined...." is investigated from today's insight. Several statements --such as the three laws of phenomenological thermodynamics, the embedding theorem and the adiabatical uniqueness-- are used to get rid of non-equilibrium entropy as a primitive concept. In this framework, Clausius inequality of open systems can be derived by use of the defining inequalities which establish the non-equilibrium quantities contact temperature and non-equilibrium molar entropy which allow to describe the interaction between the Schottky system and its controlling equilibrium environment.

In the field of railroad safety, effective detection of surface cracks is critical, necessitating reliable, high-speed non-destructive testing (NDT) methods. This study introduces a hybrid Eddy Current Testing (ECT) probe, specifically engineered for railroad inspection, to address the common issue of ’lift-off noise’ due to varying distances between the probe and test material. Unlike traditional ECT methods, this probe integrates transmit and differential receiver coils, aiming to enhance detection sensitivity and minimize lift-off impact. The study optimizes ECT probes employing different driver coils, emphasizing three main objectives: a) quantitatively evaluating each probe using signal- to-noise ratio (SNR) and outlining a real-time data processing algorithm based on SNR methodology; b) exploring the frequency range proximal to the electrical resonance of the receiver coil; c) examining sensitivity variations across varying lift-off distances. The experimental outcomes indicate that the newly designed probe with figure 8-shape driver coil significantly improves sensitivity in detecting surface cracks on railroads. It achieves an impressive SNR exceeding 100 for defects with minimal dimensions of 1 mm in width and depth. Simulation results closely align with experimental findings, validating the investigation of optimal operational frequency and lift-off distance for selected probe performance, determined to be 0.3 MHz and 0.5 mm, respectively. The realization of this project would lead to notable advancements in enhancing railroad safety by improving crack detection efficiency.

We derive time evolution equations, namely the Schrodinger-like equations and the Klein-Gordon equations for coherent fi elds and the Kadanoff-Baym (KB) equations for quantum fluctuations, in Quantum Electrodynamics (QED) with electric dipoles in 2 + 1 dimensions. Next we introduce a kinetic entropy current based on the KB equations in the 1st order of the gradient expansion. We show the H-theorem for the Leading-Order self-energy in the coupling expansion (the Hartree-Fock approximation). We show a conserved energy in the spatially homogeneous systems in the time evolution. We derive aspects of the super-radiance and the equilibration in our single Lagrangian. Our analysis can be applied to Quantum Brain Dynamics, that is QED with water electric dipoles. The total energy consumption to maintain super-radiant states in microtubules seems to be within the energy consumption to maintain the ordered systems in a brain.

An evolutionary game is introduced which considers game-theoretic strategies in the context of non-linear population matrix models. This game considers the states and actions of the organisms of the evolving population, and a notion of dynamic equilibrium between strategies is described. The game’s formalism is expounded and a proof about equilibrium is given; specifically that any stable equilibrium can be described by proportions of pure strategies; particularly when population matrices are not defective.

The Boltzmann-Gibbs (BG) entropy has been used in a wide variety of problems for more than a century. It is well known that BG entropy is extensive, but for certain systems such as those dictated by long-range interactions, the entropy must be non-extensive. Tsallis entropy possesses non-extensive characteristics, which is parametrized by a variable q (q = 1 being the classic BG limit), but unless q is determined from microscopic dynamics, the model remains but a phenomenological tool. To this date very few examples have emerged in which q can be computed from first principles. This paper shows that the space plasma environment, which is governed by long-range collective electromagnetic interaction, represents a perfect example for which the q parameter can be computed from micro-physics. By taking the electron velocity distribution function measured in the heliospheric environment into account, and considering them to be in quasi equilibrium state with electrostatic turbulence known as the quasi-thermal noise, it is shown that the value corresponding to q = 9/13 = 0.6923 may be deduced. This prediction is verified against observation made by spacecraft, and it is shown to be in excellent agreement.

Combining modern thermodynamics theory branches, including finite time thermodynamics or entropy generation minimization, constructal theory and entransy theory, with metallurgical process engineering, this paper provides a new exploration on generalized thermodynamic optimization theory for iron and steel production processes. The theoretical core is to thermodynamically optimize performances of elemental packages, working procedure modules, functional subsystems, and whole process of iron and steel production processes with real finite-resource and/or finite-size constraints with various irreversibilities toward saving energy, decreasing consumption, reducing emission and increasing yield, and to achieve the comprehensive coordination among the material flow, energy flow and environment of the hierarchical process systems. A series of application cases of the theory are reviewed. It can provide a new angle of view for the iron and steel production processes from thermodynamics, and can also provide some guidelines for other process industries.

A statistical simulation is presented which reproduces the correlation obtained from EPR coincidence experiments without non-local connectivity. In addition to the spin polarization, we identify spin coherence as an attribute, and complementary to polarization, which is anti-symmetric and generates the helicity. This changes the point particle spin to a structured one with two orthogonal magnetic moments of spin $\frac{1}{2}$ each. They couple in free flight to form a spin 1, a boson. Upon encountering a filter, the boson decouples into its two independent spins axes of $\frac{1}{2}$, with one aligning with the filter and the other randomizing. The process of decoupling from a free-flight boson to a measured fermion is responsible for the quantum correlation which results in the observed violation of Bell's Inequalities. The only variable in this work is the angle that orients a spin on the Bloch sphere, first identified in the 1920's. The new features introduced here result from changing the spin symmetry from SU(2) to the quaternion group, $Q_8$.

In order to solve the problem of large eddy current loss and high temperature rise caused by large amount of permanent magnet, a new type of combined magnetic pole permanent magnet motor is proposed in this paper. The sinusoidal distribution subdomain model of non-uniform air gap rotor is established by using Laplace equation, and the analytical expression of eddy current loss of rotor in uniform air-gap and non-uniform air-gap is derived. The effect of rotor eccentricity on eddy current loss is obtained. According to the characteristics of distributed winding of non-uniform air gap combined pole permanent magnet motor, equivalent treatment is performed to obtain the equivalent thermal conductivity, so as to establish equivalent thermal network model of motor, calculate the temperature value of each component of the motor, and verify the correctness of the thermal network model through the method of magnetothermal bidirectional coupling. Finally, an experimental platform is set up to carry out temperature rise experiments on the two prototypes respectively. Experimental results show that the non-uniform air-gap rotor structure can effectively reduce the rotor eddy current loss and motor temperature rise, and also verify the accuracy of the analytical model calculation results.

Nonionizing millimeter-waves (MMW) interact with cells in a variety of ways. Here the inhibited cell division effect was investigated using 85-105 GHz MMW irradiation within the ICNIRP (International Commission on Non-Ionizing Radiation Protection) non-thermal 20 mW/cm2 safety standards. Irradiation using a power density of about 1.0 mW/cm2 , SAR over 5-6 hours on 50 cells/μl samples of Saccharomyces cerevisiae model organism resulted in 62% growth rate reduction compared to the control (sham). The effect was specific for 85-105 GHz range, and was energy and cell density dependent. Irradiation of wild type and Δrad52 (DNA damage repair gene) deleted cells presented no differences of colony growth profiles indicating non-thermal MMW treatment does not cause permanent genetic alterations. Dose versus response relations studied using a standard horn antenna (~1.0 mW/cm2) and compared to that of a compact waveguide (17.17 mW/cm2) for increased power delivery resulted in complete termination of cell division via non-thermal processes supported by temperature rise measurements. We have shown that non-thermal MMW radiation has potential for future use in treatment of yeast related diseases and other targeted biomedical outcomes.

Background: During the stay in the neonatal intensive care unit, parents play a crucial role in the care of their infants. Recent studies reported a decrease in parental participation due to Coronavirus Disease (COVID-19) pandemic that determined restricted access policies in hospitals. The aim of this study is to describe the barriers to a good parents’ participation during the stay in the neonatal intensive care unit in the COVID-19 era. Methods: A quantitative observational study was carried out. Results: 270 parents participated in this study. Mothers’ participation in care seems to be higher as compared to fathers (p = 0.017). Parents who lived the birth of their first child reported a better level of participation in care when compared to those who lived the birth of their second born (p = 0.005). Parents of extremely preterm neonates reported a lower interaction with their infant if compared to parents of term newborns (p < 0.001). Conclusions: Some more disadvantaged categories have reported lower scores: cultural and linguistic minorities, parents of multiple children and fathers. COVID-19 pandemic made several Family Centred Care activities not possible with a higher impact on those who benefited the most of these facilities. This study was prospectively registered by the IRB-CRRM of the University “G. d’Annunzio” Chieti-Pescara on the 23/01/2024 with registration number CRRM;2023_12_07_01.

Evolutionary theory suggests that the origin, persistence, and evolution of biology is driven by the “natural selection” of characteristics improving the differential reproductive success of the organism in the given environment. The theory, however, lacks physical foundation, and, therefore, at best, can only be considered a heuristic narrative, of some utility for assimilating the biological and paleontological data at the level of the organism. On deeper analysis, it becomes apparent that this narrative is plagued with problems and paradoxes. Alternatively, non-equilibrium thermodynamic theory, derived from physical law, provides a physical foundation for describing material interaction with its environment at all scales. Here we describe a “natural thermodynamic selection” of characteristics of structures (or processes), based stochastically on increases in the global rate of dissipation of the prevailing solar spectrum. The different mechanisms of thermodynamic selection are delineated for the different biotic-abiotic levels, from the molecular level at the origin of life, up to the level of the present biosphere with non-linear coupling of biotic and abiotic processes. At the levels of the organism and the biosphere, the non-equilibrium thermodynamic description of evolution resembles, respectively, Darwinian and Gaia descriptions, although the underlying mechanisms and the objective function of selection are fundamentally very different.

Understanding the nature of the Dark Matter (DM) is one of the current challenges in modern astrophysics and cosmology. Knowing the properties of the DM particle would shed light on physics beyond the Standard Model and even provide us with details of the early Universe. In fact, the detection of such a relic would bring us information from the pre-Big Bang Nucleosynthesis (BBN) period, an epoch from which we have no data, and could even hint at inflationary physics. In this work, we assume that the expansion rate of the Universe after inflationary is governed by the kinetic energy of a scalar field ϕ, in the so-called “kination” model. We assume that the ϕ field decays into both radiation and DM particles, which we take to be Weakly Interacting Massive Particles (WIMPs). The present abundance of WIMPs is then fixed during the kination period through either a thermal “freeze-out” or “freeze-in” mechanism, or through a non-thermal process governed by the decay of ϕ. We explore the parameter space of this theory with the requirement that the present WIMP abundance provides the correct DM relic budget. Requiring that BBN occurs during the standard cosmological scenario sets a limit on the temperature at which the kination period ends. Using this limit and assuming the WIMP has a mass m_χ = 100 GeV, we obtain that the thermally-averaged WIMP annihilation cross section has to satisfy the constraints 3.5 × 10⁻¹⁶ GeV⁻² ≲ (σv) ≲ 1.4 × 10⁻⁵ GeV⁻² in order for having at least one of the production mechanism to yield the observed amount of DM. This result shows how the properties of the WIMP particle, if ever measured, can yield information on the pre-BBN content of the Universe.

The Predicted Mean Vote (PMV) and the Predicted Percentage of Dissatisfied (PPD) indices are used to assess the indoor environment in terms of human thermal comfort-discomfort. In this study, an experimental combined objective and subjective investigation of thermal comfort perception has been performed in students between 16-18 years old, in a non-air-conditioned school building. The objective approach included instrumentation measurements and data processing according to ISO 7730, whereas, the subjective one was based on answers collection following ISO 10551. The study is mainly devoted to the verification of Fanger’s approach in a building, in free running conditions, under a mild (moderate) climate.The comparison between instrumentation data and questionnaire results presented an underestimation of the mean vote, predicting a cooler sensation than the actual one.

We present a mixing length based algebraic turbulence model calibrated to pipe flow; the main purpose of the model is to capture the increasing turbulence production-to-dissipation ratio observed in connection with the high Reynolds number transition region. The model includes the mixing length description by Gersten and Herwig which takes the observed variation of the von Kármán number with Reynolds number into account. Pipe wall roughness effects are included in the model. Results are presented for area-averaged (integral) quantities which can be used both as a self-contained model and as initial inlet boundary conditions for computational fluid dynamics simulations.

Steady-state one-dimensional flows of five-component air behind a normal shock wave are considered with one-temperature model. A mathematical model is formulated to describe the relaxation of a five-component air mixture with a one-temperature non-equilibrium approximation. A numerical study of non-equilibrium flows of a reacting five-component air mixture behind shock waves at different heights and velocities of free flow is performed. The contribution of different types of reactions to the overall relaxation of the mixture is discussed, and the distributions of macro-parameters of the flow behind the shock wave front are calculated. The lengths of the relaxation zones behind the shock wave front are compared at different initial conditions.

Although most biological processes are characterized by a strong temporal asymmetry, several popular mathematical models neglect this issue. Maximum entropy methods provide a principled way of addressing time irreversibility, which leverages powerful results and ideas from the3literature of non-equilibrium statistical mechanics. This article provides a comprehensive overview of these issues, with a focus in the case of spike train statistics. We provide a detailed account of the5mathematical foundations and work out examples to illustrate the key concepts and results from non-equilibrium statistical mechanics

Mechanically homogenized composite of expanded graphite and cobalt(II) rhenate(VII) has been described. Cobalt(II) rhenate(VII) was obtained in a reaction of perrhenic acid with cobalt(II) nitrate. A simple mortar homogenization method was used to enhance intercalation of cobalt species within carbon matrix. The specific capacity of composite was enhanced by 50% in comparison to bare expanded graphite. The electrochemical characteristic was significantly improved including better cyclability, lower resistance of electrode material, lower iR drop, with respect to expanded graphite without cobalt(II) rhenate(VII) active species. Expanded graphite with its unique specific surface area and pore size diameter was proved as potential and cheap carbon support.

An electrothermal analysis for barium titanate based ceramics is presented combining the Heywang–Jonker model for the electric resistivity with a heat dissipation mechanism based on natural convection and radiation in a one dimensional model on the device level with voltage as the control parameter. Both PTC and NTC effects are accounted for through the double Schottky barriers at the grain boundaries of the material. The problem formulated in this way admits uniform and non–uniform multiple steady state solutions that do not depend on the external circuit. The numerical bifurcation analysis reveals that the PTC effect gives rise to several multiplicites above the Curie point, whereas the NTC effect is responsible for the thermal runaway (temperature blowup). The thermal runaway phenomenon as a potential thermal shock could be among the possible reasons for the observed thermomechanical failures (delamination fracture). The theoretical results for the NTC regime and the thermal runaway are in agreement with experimental flash sintering results obtained for 3% and 8% yttria stabilized zirconia.

This study presents a preliminary analysis of the chemical and thermal fuel properties of Afuze (AFZ) coal extracted from coalfields in Owan East Local Government Area of Edo State, Nigeria. The chemical properties of AFZ were examined by combined scanning electron microscopy-energy dispersive X-ray (EDX), whereas the thermal properties were deduced by thermogravimetric analysis (TGA) under flash (50 °C/min heating rate) oxidative (combustion) and non-oxidative (pyrolysis) conditions. The microstructure and morphology analysis of AFZ revealed has a compact structure comprising small-to-large, irregular shaped and exfoliated grains with a vitreous appearance typically ascribed to metal elements (Ti and Fe) kaolinite, quartz, and other clay minerals. Chemical analysis revealed carbon, oxygen, aluminium, silicon, sulphur, calcium, titanium, and iron in major and minor (trace) quantities. Thermal analysis under oxidative and non-oxidative conditions revealed degradation occurs in three stages, namely; drying or demineralisation, devolatilization or maceral degradation and the formation of char/coke or ash. Lastly, the findings showed that the temperature range for the oxidative thermal degradation process (338.58 - 756.76 °C) was higher than the non-oxidative process (378.43 - 615.34 °C). This observation can be explained by the exothermic nature of the oxidative (combustion) process, which ensures greater heat supply required to thermally soften or degrade the maceral coal components. Overall, the oxidative process yielded the residual mass (RM = 21.97%) and mass loss (ML = 78.03%). The lower ML (49.03%) but higher RM (50.97%) observed during non-oxidative degradation of AFZ could be ascribed to the largely endothermic nature of the process.

In this work model of mirror elements equilibrium of the micromechanical components is developed, the behavior analysis of the mirror element of micromechanical mirrors in case changing of control voltages of electrostatic actuators is carried out, an expression for determining the maximum value of deflection voltage at which the snap-down effect will take the following form is obtained in case of the influence of the coefficient of the electrostatic rigidity of electrostatic actuators. The developed equilibrium model of mirror elements and the obtained results of modeling can be used at design of micromechanical mirrors with internal suspensions.

The study investigated the application of Wastewater-Based Epidemiology (WBE) as a tool for monitoring SARS-CoV-2 prevalence in a city in Northern Italy from October 2021 to May 2023. Starting from a widely applied deterministic model, this study proposed a variation to take into account population characteristics and virus biodegradation in the sewer network. The model calculated virus loads and corresponding COVID-19 cases over time in different areas of the city and was validated with healthcare data while considering viral mutations, vaccinations, and testing variability. The correlation between the predicted and reported cases was high across the three waves that occurred in the considered period, demonstrating the model’s capacity to predict relevant fluctuations in the number of cases. Population characteristics did not substantially influence the predicted and reported infection rates. Conversely, biodegradation significantly reduced the virus load reaching the wastewater treatment plant, resulting in a 30% reduction in the total virus load produced in the study area. This approach can be applied for comparing virus load values across cities with varying population demographics and sewer network structures, enhancing the comparability of WBE data for effective surveillance and intervention strategies.

Microwave technology has a potential application in the extraction of zinc from sulphide ores, knowledge of the dielectric properties of these ores plays a major role in the microwave design and simulation for any process. The dielectric properties of zinc sulfide concentrate for two different apparent densities—1.54 and 1.63 g/cm³—have been measured by using the resonance cavity perturbation technique at 915 and 2450 MHz during the roasting process for the temperature ranging from room temperature to 850 °C. The variations of dielectric constant, the dielectric loss factor, the dielectric loss tangent and the penetration depth with the temperature, frequency and apparent density have been investigated numerically. The results indicate that the dielectric constant increases as the temperature increases and temperature has a pivotal effect on the dielectric constant, while the dielectric loss factor has a complicated change and all of the temperature, frequency and apparent density have a significant impact to dielectric loss factor. Zinc sulfide concentrate is high loss material from 450 to 800 °C on the basis of theoretical analyses of dielectric loss tangent and penetration depth, its ability of absorbing microwave energy would be enhanced by increasing the apparent density as well. The experimental results also have proved that zinc sulfide concentrate is easy to be heated by microwave energy from 450 to 800 °C. In addition, the experimental date of dielectric constant and loss factor can be fitted perfectly by Boltzmann model and Gauss model, respectively.

Telerehabilitation is an appealing service delivery option for optimising recovering. Internationally, the equity of telerehabilitation services for people from culturally and linguistically diverse (CALD) backgrounds has been questioned. Using a 31-item survey, our study explored the access, readiness, and willingness of 260 patients to use allied health telerehabilitation services for adults receiving interventions from a large tertiary health service located in Sydney, Australia. Overall, 72% patients reported having access to technology, 38% met our readiness criteria, and 53% reported willingness to engage in telerehabilitation. There were no difference in access, readiness and willingness to engage in telerehabilitation between patients from CALD and non-CALD backgrounds. Age was the only factor that influenced access, readiness and willingness to engage in telerehabilitation. Past experience of telerehabilitation was related to willingness, but not access or readiness. Findings highlight the importance of ensuring positive patient experiences to promote ongoing willingness to use telerehabilitation. Efforts are needed to improve patients’ digital health literacy, especially patients from older age groups, to ensure equitable access to telerehabilitation services.

A probabilistic description is essential for understanding the dynamics of stochastic systems far from equilibrium, given uncertainty inherent in the systems. To compare different Probability Density Functions (PDFs), it is extremely useful to quantify the difference among different PDFs by assigning an appropriate metric to probability such that the distance increases with the difference between the two PDFs. This metric structure then provides a key link between stochastic systems and information geometry. For a non-equilibrium process, we define an infinitesimal distance at any time by comparing two PDFs at times infinitesimally apart and sum these distances in time. The total distance along the trajectory of the system quantifies the total number of different states that the system undergoes in time, and is called the information length. By using this concept, we investigate the information geometry of non-equilibrium processes involved in disorder-order transitions between the critical and subcritical states in a bistable system. Specifically, we compute time-dependent PDFs, information length, the rate of change in information length, entropy change and Fisher information in disorder-to-order and order-to-disorder transitions, and discuss similarities and disparities between the two transitions. In particular, we show that the total information length in order-to-disorder transition is much larger than that in disorder-to-order transition, and elucidate the link to the drastically different evolution of entropy in both transitions. We also provide the comparison of the results with those in the case of the transition between the subcritical and supercritical states and discuss implications for fitness.

Energy metabolism regulates the proliferation of stem cells by regulating energy production and the production of substrates through biosynthetic pathways. It is an important target for cell regulation and stem cell applications, and is crucial for determining the pluripotency and cell fate of stem cells. In this context, this article focuses on reviewing the latest research progress on the association between glucose metabolism, amino acid metabolism, fatty acid metabolism, and mitophagy with stem cell function, elucidating how key energy metabolism pathways affect stem cell function by regulating signal transduction and epigenetic modifications. In this review, we discuss the key factors affecting energy metabolism and their association with stem cell function. The integration of energy metabolism and stem cell fate regulation will open up a new path for future regenerative medicine practices.

Sialylated milk oligosaccharides (SMOs) is the most important oligosaccharides in human milk oligosaccharides (HMOs), and have a multifunctional health benefit, and the most abundant SMOs are sialyllactose (SLs). The previous studies indicate that the growth of tumor cells, and angiogenesis on tumor tissues with Lewis lung carcinoma, melanoma, and colon carcinoma cells could be prevented by SL. Thus, it has been proposed that SL might be an ideal candidate for the development of anti-angiogenic drugs without any side effects. It has been proposed that the Sialic acid (Sia) can be produced through SL’s hydrolysis, and the dietary Sia is further transported to the brain and other tissues though blood for formation of CMP-Sia, the activated precursor of Sia, and then is catalyzed by polysialyltransferases (polySTs) for synthesis of polysialic acid (polySia) or polysialylation of neural cell adhesion molecule (NCAM). Thus, it’s necessary to study and develop new inhibitors, which not only modulate a proper balance between the gut health and neuros system development, but also inhibit the overexpression of polySia, and thus block the tumor cell migration. In this study, we proposed that 3’-SL and 6’-SL may be more ideal inhibitors comparing with two previous inhibitors, the low molecular weight heparin (LMWH) and cytidine monophosphate (CMP) in the previous studies.

During choriogenesis in insects, chorion (eggshell) is formed by surrounding follicular epithelial cells in ovarioles. However, the regulatory endocrine factor(s) activating choriogenesis and the chemical components on eggshell deserve further exploration. In two representative Coleopterans, a Coccinellid Henosepilachna vigintioctopunctata and a Chrysomelid Leptinotarsa decemlineata, genes encoding the 20-hydroxyecdysone (20E) receptor heterodimer, ecdysone receptor (EcR) and ultraspiracle (USP), and two chitin biosynthesis enzymes UDP-N-acetylglucosamine pyrophosphorylase (UAP) and chitin synthase (ChS1), were highly expressed in ovaries of the young females. RNA interference (RNAi)-aided knockdown of either HvEcR or Hvusp in H. vigintioctopunctata inhibited oviposition, suppressed the expression of HvChS1, and lessened the positive signal of Calcofluor staining on the chorions, which suggests the reduction of a chitin-like substance (CLS) deposited on eggshells. Similarly, RNAi of LdEcR or Ldusp in L. decemlineata constrained oviposition, decreased the expression of LdUAP1 and LdChS1, and declined CLS contents in the resultant ovaries. Knockdown of LdUAP1 or LdChS1 caused similar defective phenotypes, i.e., reduced oviposition and CLS contents in the L. decemlineata ovaries. These results, for the first time, indicate that 20E signaling activates choriogenesis in two Coleopteran species. Moreover, our findings propose the deposition of a CLS on the chorions.

It is shown how the secondary structure of proteins, musical forms and verses of poems are approximately ruled by universal laws relying on graph coverings. In this direction, one explores the group structure of a variant of the SARS-Cov-2 spike protein and the group structure of apolipoprotein-H, passing from the primary code with amino acids to the secondary structures organizing the foldings. Then one look at the musical forms employed in the classical and contemporary periods. Finally, one investigates in much detail the group structure of a small poem in prose by Charles Baudelaire and that of the Bateau Ivre by Arthur Rimbaud.

1) Background: the budget of non-thermal energy in galaxy clusters is not well constrained, owing to the observational and theoretical difficulties in studying these diluted plasmas on large scales. 2) Method: we use recent cosmological simulations with complex physics in order to connect the emergence of non-thermal energy to the underlying evolution of gas and dark matter. 3) Results: the impact of non-thermal energy (e.g. cosmic rays, magnetic fields and turbulent motions) is found to increase in the outer region of galaxy clusters. Within numerical and theoretical uncertainties, turbulent motions dominate the budget of non-thermal energy in most of the cosmic volume. 4) Conclusion: assessing the distribution non-thermal energy in galaxy clusters is crucial to perform high-precision cosmology in the future. Constraining the level of non-thermal energy in cluster outskirts will improve our understanding of the acceleration of relativistic particles by cosmic shocks and of the origin of extragalactic magnetic fields.

The nonlocality of entangled quantum mechanical systems is incompatible with the standard interpretation of special relativity as a single 4D Minkowskian metric spacetime. The difficulty is that the definition of a spacetime interval between any pair of events precludes any form of nonlocal interaction, even the relatively benign non-signaling correlations. By an application of the relativity principle, and the use of the space ←→ time symmetry of the Lorentz boost I propose here a reinterpretation of special relativistic spacetime. This new ontology consists of a set of coexisting 3+1D spaces (‘framespaces’), each containing unique content in the form of a complex density. These spaces are related by the Lorentz boost, and coupled pairwise in a manner dictated by the Lorentz transformation. The inter-space coupling acting on the spacetime content gives rise to a nonlocal wave phenomenon, which is identified as quantum wave mechanics. The interspace coupling strength is then inversely proportional to Planck’s constant. The coexistence of multiple spaces is interpreted as momentum superposition, implying that momentum is the fundamental physical basis of quantum superposition. This new spacetime interpretation of quantum mechanics has many consequences, including explanations of quantum non-locality, the spacetime role of Planck’s constant, quantum measurement as a symmetry-breaking process and the redundancy of description of gauge theory.

The powder bed fusion (PBF) metal additive manufacturing (AM) method uses an energy source like a laser to melt the metal powders. The laser can locally melt the metal powders and creates a solid structure as it moves. The complexity of the heat distribution in laser PBF metal AM is one of the main features that need to be accurately addressed and understood to design and manage an optimized printing process. In this research, the dependency of local thermal rates and gradients on print after solidification (in the heat-affected zone) was numerically simulated and studied to provide information for designing the print process. The simulation results were validated by independent experimental results. The simulation shows that the local thermal rates are higher at higher laser power and scan speed. Also, the local thermal gradients increase if the laser power increases. The effect of scan speed on the thermal gradients is opposite during heating versus cooling times. Increasing the scan speed increases the local thermal gradients in the cooling times and decreases the local thermal gradients during the heating. In addition, these simulation results could be used in artificial intelligence (AI) and machine learning for developing digital additive manufacturing.

Being able to express broad families of equivariant or invariant attributed graph functions is a popular measuring stick of whether graph neural networks should be employed in practical applications. However, it is equally important to learn deep local minima of losses (i.e., with much smaller loss values than other minima), even when architectures cannot express global minima. In this work we introduce the architectural property of attracting GNN optimization trajectories to local minima as a means of achieving smaller losses. We take first steps in satisfying this property for losses defined over attributed undirected unweighted graphs with a novel architecture, called Universal Local Attractor (ULA). The latter refines each dimension of end-to-end trained node feature embeddings based on graph structure to track the optimization trajectories of losses satisfying some mild conditions. The refined dimensions are then linearly pooled to create predictions. We experiment on 10 tasks, from node classification to clique detection, on which ULA is comparable with or significantly outperforms popular alternatives of similar or greater theoretical expressive power.

This paper aims to study and analyze the effect of the flow rate and amplitude of walling waves on the peristaltic flow of Jeffrey’s fluid through an irregular channel. In addition, it analyses streamlined patterns and their local and global bifurcation flow. The theory of dynamical systems is used to explore the position of critical points and their bifurcation. Numerical and analytical methods are presented to display effective changes in amplitude and rate of the flow on the transport of fluid. Three types of streamline patterns occur backward, trapping and augmented flow in the channel through movement due to changes in the value rate parameters.

In this work, we analytically describe a superconducting transition in a non-equilibrium state taking into account many-body interactions; the obtained transition temperatures indicate the presence of superconductivity at room temperatures.First, we consider many-body interactions and discuss the case of locally thermal equilibrium with many-body interactions; in this section, we derive statistical equations that describe many-body interactions at locally thermal equilibrium state. Then, the same theory is used to derive a many-body statistical equation that is expanded to include the case of non-equilibrium states; in this case a transition temperature is derived. Moreover, a wave function of an Einstein–Podolsky–Rosen pair (EPR pair) is calculated according to the Lorentz conservation, and a specific condensation is observed and the Meissner effect is found to be present.Furthermore, considering the Lorentz conservations, relativistic energy, and Boltzmann statistics, algorithms are presented to calculate charge density, current density, and internal local energy. We note that these calculations do not require a specific code but instead utilize the software Microsoft Excel.We present plots showing the charge density and current density vs. the applied electric potential, which demonstrate the practical applicability of the theory. Moreover, internal local energy was found to be close to zero for sufficiently large electric potentials at room temperature.In the discussion section, the universally induced superconducting current is derived, which can be employed as the renewable energy.This paper describes non-equilibrium and EPR-pair type superconductivity, with the complete consideration of many-body interactions.

In humans, age-associated degrading changes are observed in molecular and cellular processes underly the time-dependent decline in spatial navigation, time perception, cognitive and psy-chological abilities, and memory. Cross talk of biological, cognitive, and psychological clocks provides an integrative contribution to healthy and advanced aging. At the molecular level, ge-nome, proteome, and lipidome instability are widely recognized as the primary causal factors in aging. We narrow attention to the roles of protein aging linked to prevalent amino acids chirali-ty, enzymatic and spontaneous (non-enzymatic) post-translational modifications (PTMs SP), and non-equilibrium phase transitions. The homochirality of protein synthesis, resulting in the steady-state non-equilibrium condition of protein structure, makes them prone to multiple types of enzymatic and spontaneous PTMs, including racemization and isomerization. Spontaneous racemization leads to the loss of the balanced prevalent chirality. Advanced biological aging re-lated to irreversible PTMs SP has been associated with the nontrivial interplay between poor so-matic and mental health conditions. Through stress response systems (SRS), the environmental and psychological stressors contribute to the age-associated “collapse” of protein homochirality. The role of prevalent protein chirality and entropy of protein folding in biological aging is mainly overlooked. In a more generalized context, the time-dependent shift from enzymatic to the non-enzymatic transformation of biochirality might represent an important and yet un-der-appreciated hallmark of aging.

Soil extracellular enzyme activity (EEAs) and enzymatic stoichiometry (ES) can provide a crucial indication of changes in soil ecosystem's nutrient availability and the microbial resource limitations. However, the changing characteristics of soil EEAs and ES at different stages of the native succession process and their key drivers are unclear. In order to investigate the soil EEAs, ES and driving factors of soil under vegetation at different succession stages, we adopted the "spatio-temporal substitution" method to collect the surface soil of bryophyte community, herbaceous community, shrub community and tree community in the new volcanic lava platform of Wudalianchi Volcanic Nature Reserve. We measured seven soil EEA, including carbon(C)-acquiring enzyme (β-1,4-glucosidase (BG)), N-acquiring enzymes (β-N-acetyl-glucosaminidase (NAG) and leucine aminopeptidase (LAP)) and phosphorus (P)-acquiring enzyme (acid phosphatase (AP)) activities. The length and angle of vectors defined by ratios of enzyme activities (BG/(NAG + LAP) vs. BG/AP) were used to indicate relative microbial investments in C- (length), and N- and P- (angle) acquiring enzymes. Our results showed that the contents of TC, TN, TP, MBC, DOC and NO3-N in shrub community soil were significantly higher than those in bryophyte, herb and tree communities, and increased by 441%, 246%, 137%, 5570%, 12% and 484%, respectively. The highest soil EEA of C-, N- and P-acquiring were found in shrub community, and the soil EEAs/MBC of C-, N- and P-acquiring were the highest in bryophyte community. Enzyme C:N, C:P and N:P ratios increased progressively in the order of bryophyte, herb and shrub community, but the enzyme C:N, C:P and N:P ratios of tree community were both far less than shrub community. Vector lengths increased progressively in the order of bryophyte (1.16), herb (1.27), tree (1.29) and shrub (1.40), and Vector angles decreased progressively in the order of bryophyte (49.15°), herb (45.65°), Tree (45.31°) and shurb (44.54°), suggested that as succession progresses, soil microbial nutrients transforms from P limitation (angle＞45°) to N limitation (angle＜45°). Redundancy analysis showed that TC, TN, EC and C:N were important drivers of variation in soil EEAs and ES in vegetation at different succession stages. Our findings highlight that the primary succession process cause nutrient limitation transformation. Soil ES might be a sensitive indicator mediated by soil microorganisms to the relative resource limitation at different stages of the primary succession process.

Based on the Generalized bracket, or Beris-Edwards, formalism of non-equilibrium thermodynamics, we have recently proposed [Stephanou et al. Materials, 13, 2867 (2020)] a new differential constitutive model for the rheology of entangled polymer melts and solutions. It has amended the shortcomings of a previous model that was too strict in the values of the convective constraint release parameter for the model not to violate the second law of thermodynamics and has been shown capable of predicting a transient stress undershoot (following the overshoot) at high shear rates. In this work, we wish to further examine this model’s capability of predicting the rheological response of industrial polymer systems by extending it to its multiple-mode version. The comparison against industrial rheological data (High-Density Polyethylene resins), as compared against available experimental data in (a) Small Amplitude Oscillatory shear, (b) start-up shear, and (c) start-up uniaxial elongation, is noted to be good.

Considered is “time as an interval” including time from the past and from the future, in contrast to time as a moment. Equilibrium as the basis for a description of changing properties in physics is understood to depend on the “mean velocity theorem”, while a “time” of equilibrium resembles a center of weight. This turns out to be a good method to derive properties for any function of time t including space coordinates q(t) and expressions for the time dependent Hamiltonian. Introduced are derivatives depending on time intervals instead of time moments and with these a new relation between the Lagrangian L and the Hamiltonian H. As an application introduced is a step by step method to integrate stationary state “local” time interval measurements to beyond “locality” in General Relativity. Because of limits on the measures of the resulting time intervals and their asymmetry, this allows for a probabilistic interpretation of quantities that have these intervals as time domain in QM. Their asymmetry also questions the time reversal symmetry of GR. Another application of time intervals is the discussion of the measurement of starlight radiation energy and QM wave packet collapse as an example of a time dependent Hamiltonian. Finally a relation between starlight frequency, metric and space- and time intervals is found. Discussed is how finite and asymmetric time intervals correspond to time dependent H and symmetric infinite time intervals to a time independent H. From there, in cosmological perspective, finite time intervals can help to describe how entropy change could relate to dark energy.

Thermal Non-destructive Testing and Evaluation (NDT&E) is crucial in ensuring the quality and safety of industrial materials, components, and structures. It serves as a key tool for assessing their operational reliability, thus enhancing safety in a wide range of industries. There is a growing demand for dependable, swift, remote, and secure inspection and assessment techniques to detect hidden flaws, especially for sustainable solutions prompts adjustments in design and manufacturing standards. Hidden defects often emerge during the service life of these materials and structures due to various stress factors, potentially resulting in catastrophic failures. This study delves into the optimal and dependable experimental method for conducting fast, remote, and secure inspections and assessments of carbon fiber reinforced polymer materials using Infrared Imaging (IRI) as part of Thermal Non-Destructive Testing and Evaluation (TNDT&E). Additionally, it examines the post-processing approach associated with this technique. This perspective also sheds light on the current state-of-the-art infrared imaging methods employed in TNDT&E, emphasizing their strengths and weaknesses about their ability to detect subsurface defects present within the material Most of the methods discussed in previous research primarily focus on the thermal differences in specific areas of a sample using processed thermal images, even though these images come from analyzing a series of images captured over time. This study highlights the latest research in thermal/infrared non-destructive testing and evaluation, along with the related post-processing techniques. It aims to not only show hidden subsurface defects through thermal differences also provides information about how these defects change over time.

The expression of polysialic acid (polySia) on the neuronal cell adhesion molecule (NCAM), is called NCAM-polysialylation, which is strongly related to the migration and invasion of tumor cells and with aggressive in the clinic. Thus, it’s important to select a proper drug to block tumor cell migration for clinic treatment. In this study, we proposed that lactoferrin (LFcinB11) may be a more ideal candidate for inhibition of NCAM polysialylation comparing with CMP and low molecular weight heparin (LMWH), which were determined based on our NMR studies. On the other hand, because neutrophil extracellular traps (NET) is the most dramatic stage in cell death process, and NETs’ release are related to pathogenesis of autoimmune and inflammatory disorders, with proposed involvement in glomerulonephritis, chronic lung disease, sepsis and vascular disorders. In this study, the molecular mechanism of inhibition of NETs’ release using LFcinB11 as inhibitor was also determined. Based on these results, LFcinB11 is proposed to be bifunctional inhibitor for inhibiting both NCAM polysialylation and NETs releases.

We propose novel spectrometer designs that aim to enhance the measured spectral range 1 of ions on a finite-sized detector. In contrast to the traditional devices that use uniform magnetic 2 field, in which the deflection of particles increases inversely proportional to their momentum, in a 3 gradient magnetic field, the deflection of particles will be decreased due to the reduction of the 4 magnetic field along their propagation. Low energy ions are particularly impacted, as they are 5 deflected less and are more likely to reach the detector compared to being driven out of it while 6 using a uniform magnetic field. By the means of a gradient magnetic field, the nonlinear dispersion 7 of ions in a homogeneous magnetic field can approach a nearly linear dispersion. Nonetheless, 8 the dispersion of low energy ions in a homogeneous magnetic field remains unnecessarily high. 9 In this article, we explore linear, quadratic, and higher-order field profiles in comparison to the 10 homogeneous field case. We discuss the employed methodology and present simulation results of 11 the spectrometer with an extended ion spectral range, focusing on the minimum detectable energy 12 (energy dynamic range) and energy resolution

The objective of this paper was to verify the applicability of statistical learning (SL) compared to human reasoning with respect to the Universal Thermal Climate Index (UTCI), a complex tool for the assessment of outdoor thermal stress. UTCI is an equivalent temperature index based on the 48-dimensional output of an advanced model of human thermoregulation formed by 12 variables at four consecutive 30-minute intervals, which were calculated for 105642 thermal conditions from extreme cold to extreme heat. Comparing the performance of SL algorithms to the results accomplished by an international endeavor involving more than 40 experts from 23 countries, we found that random forests and k-nearest neighbors closely predicted UTCI values, but that clustering applied after dimension reduction algorithms (principal component analysis and t-distributed stochastic neighbor embedding) were inadequate for risk assessment in relation to the UTCI stress categories. This indicates a potential supportive role for SL, as it will not (yet) fully replace the bio-meteorological expert knowledge.

In a recent reformulation of the Marrucci-Ianniruberto constitutive equation for the rheology of entangled polymer melts in the context of non-equilibrium thermodynamics, rather large values of the convective constraint release parameter \beta_{ccr} had to be used in order not to violate the second law of thermodynamics. In this work, we present an appropriate modification of the model which avoids the splitting of the evolution equation for the conformation tensor into an orientation and a stretching part. Then, thermodynamic admissibility dictates simply that \beta_{ccr}≥ 0, thus allowing for more realistic values of \beta_{ccr} to be chosen. Moreover, and in view of recent experimental evidence for a transient stress undershoot (following the overshoot) at high shear rates whose origin may be traced back to molecular tumbling, we have incorporated in the model additional terms accounting, at least in an approximate way, for non-affine deformation through a slip parameter \xi. Use of the new model to describe available experimental data for the transient and steady-state shear and elongational rheology of entangled polystyrene melts and solutions shows close agreement. Overall, the modified model proposed here combines simplicity with accuracy, which renders it an excellent choice for managing complex viscoelastic fluid flows in large-scale numerical calculations.

Thermal camouflage is a highly sought-after technology to increase the survivability of military equipment against infrared (IR) detectors. Recently, two-dimensional (2D) nanomaterials have shown low IR emissivity, widely tunable opto-electronic properties and compatibility with stealth-applications. Among them, graphene and graphene-like materials are the most attractive 2D materials used for thermal camouflage applications. In particular, in multilayer graphene (MLG) charge density can be effectively tuned through sufficiently intense electric fields or through electrolytic gating. Therefore, MLG optical properties, like infrared emissivity and absorbance, can be controlled in a wide range by voltage bias. The large emissivity modulation achievable with this material makes it suitable in the design of thermal dynamic camouflage devices. Generally, the emissivity modulation in the multilayered graphene medium is governed by an intercalation process of non-volatile ionic liquids under a voltage bias. The electrically-driven reduction of emissivity leads to a decrease in the apparent temperature of the surface, which can match that of the background enabling thermal camouflaging. Since this property is common to other graphene-based materials, here we present a review specifically focused on the recent advances in the field of the thermal camouflage properties of graphene in the form of composite film and aerogel structures. A summary of the current understanding of the working principle of thermal camouflage materials, current limitations, and future opportunities is presented and discussed.

The oscillating heat pipe (OHP) is a new member in the family of heat pipes, and it has great potential applications in energy conservation. However, the fluid flow and heat transfer in the OHP as well as the fundamental effects of inner diameter on them have not been fully understood, which are essential to the design and optimization of the OHP in real applications. Therefore, by combining the high-speed visualization method and infrared thermal imaging technique, the fluid flow and thermal performance in the OHPs with inner diameters of 1, 2 and 3 mm are presented and analyzed. The results indicate that three fluid flow motions, including small oscillation, bulk oscillation and circulation, coexist or, respectively, exist alone with the increasing heating load under different inner diameters, with three flow patterns occurring in the OHPs, viz. bubbly flow, slug flow and annular flow. These fluid flow motions are closely correlated with the heat and mass transfer performance in the OHPs, which can be reflected by the characteristics of infrared thermal images of condensers. The decrease in the inner diameter increases the frictional flow resistance and capillary instability while restricting the nucleate boiling in OHPs, which leads to a smaller proportion of bubbly flow, a larger proportion of short slug flow, a poorer thermal performance, and easier dry-out of working fluid. In addition, when compared with the 2 mm OHP, the increasing role of gravity induces the thermosyphon effect and weakens the 'bubble pumping' action, which results in a little smaller and bigger thermal resistances of 3 mm OHP under small and bulk oscillation of working fluid, respectively.

Graphene is a two-dimensional nanostructured material with intrinsic properties that show promising performance in various applications, including electronics, renewable energy, medicine, mechanical enforcement and others. This study reports a bottom-up approach for the conversion of cyclohexane into graphene nanoflakes, which were then deposited onto fiberglass using a non-thermal generator. The composite was characterized using transmission electron microscopy, which revealed the formation of stacked few-layer graphene with a partially disordered structure and a d-spacing of 0.358 nm between the layers. X-ray diffraction confirmed the observations from the TEM images. SEM images showed the agglomeration of carbonaceous material onto the fiberglass, which experienced some delamination due to the synthesis method. Raman spectroscopy indicated that the obtained graphene exhibited a predominance of defects in its structure. Additionally, Atomic Force Microscopy (AFM) analyses revealed the formation of graphene layers with varying levels of porosity.

Aquifer Thermal Energy Storage (ATES) systems are garnering attention as high-efficiency air conditioning technologies that contribute to the realization of a carbon-neutral society. This study focuses on an ATES system constructed in Japan, characterized by its complex geological conditions and thin aquifer layers. Through performance analysis using four years of operational data, we achieved a Coefficient of Performance (COP) of 5 on the building load side. This paper confirms the equivalence of the dimensionless production temperature and heat recovery rate, observing nearly identical changes in the dimensionless production temperature over four cycles (eight seasons). Furthermore, we propose an operational method for the following fiscal year that maintains the balance between accumulated storage quantity and pumping volume, based on predictions from this plant's operational pattern.

Hydrogen has a leading role in accomplishing a net zero green-house gas emission future. Today’s challenge is producing green hydrogen to cover the fuel demand of transportation and industry, to gain independence from fossil fuels. This review’s goal is to demonstrate critically the existing methods of biomass treatment and assess their ability to scale up. Biomass is an excellent hydrogen carrier and biomass-derived processes are the main target for hydrogen production as it is an innovative pathway to green hydrogen production. Comparing the existing processes, thermochemical treatment is found to be far more evolved than biological or electrochemical treatment especially with regard to scaling prospects.

This article develops duality principles and related convex dual formulations suitable for the local optimization of non-convex primal formulations for a large class of models in physics and engineering. The results are based on standard tools of functional analysis, calculus of variations and duality theory. In particular, we develop applications to a Ginzburg-Landau type equation.

As one of the typical deposits in Sichuan-Yunnan-Guizhou Pb-Zn metallogenic province, the Daliangzi Pb-Zn deposit has a close genetic relation with the structural system of “black/fracture zone” formed under the action of NWW-approx. EW strike-slip structures in the metallogenic province, but the mechanism of rock and ore-controlling action of the structural system remains unclear. Based on detailed analysis of tectonite-mineralized alteration lithofacies of R1 “black/fracture zone”, the tectonite-mineralized alteration lithofacies zones can be divided into 4 types in succession outward from the Pb-Zn mineralization center, i.e., ① brecciated and stockwork-like Pb-Zn mineralization-complex breccia facies zone, ② stockwork-like Pb-Zn mineralization-simple breccia and cataclasite facies zone, ③ veined pyrite-sulfide-dolomitic cataclasite facies zone, and ④ fine-veined calcite-black carbonized dolomite facies zone; Cl- and SO42--rich high-temperature oxidizing ore-bearing fluid mixes with reducing fluid in Zone ① while migration and precipitation occur in Zone ④. With the evolution of ore-forming fluid, the homogenization temperature decreases from Zone ① to Zone ④, the salinity increases from Zone ① to Zone ② and then decreases to Zones ③ and ④, and the fluid density has little change on the whole; the contents of Zn, Pb, Cu, Ga, Ge, Cd, Ag, and other metallogenic elements, the Zn/Pb ratio, and the CaO/MgO mole ratio decrease gradually from Zone ① to Zone ④; and REE fractionation, calcilization, silicification, and pyritization enhance gradually from Zone ① to Zone ④. This series of changes are the product of diapirism (cryptoexplosion) of strike-slip structures and “black/fracture zone”, among which the second-order structures (F5, F100, and other faults) derived from NWW-approx. EW striking dextral shear-tension faults F1 and F15 control the brecciated and stockwork-like Pb-Zn mineralized complex breccia facies zones and the stockwork-like Pb-Zn mineralized simple breccia and cataclasite facies zones. Therefore, this paper establishes the zoning mode of tectonite-mineralized alteration lithofacies of “black/fracture zone” and proposes that Zones ① and ② are important prospecting criteria. conclusions.

The Active Distribution Networks (ADNs) are Multi-Input Multi-Output (MIMO) systems with coupled dynamics which cause interactions among the control loops of the Distributed Energy Resources (DERs). This undesired effect lead to performance degradation in the voltage control. To mitigate the effects of these unavoidable coupling, the present paper proposes a systematic design procedure based on the analysis of the interaction's sources. In details, each DER is equipped with a double loop PI to control the active and reactive powers output by the Voltage Source Converter (VSC) which connects the DER to the network's node. Furthermore, to guarantee Ancillary Services (ASs), the two loops are coupled by a simple mechanism of cooperation of the active power to voltage regulation realized by a filtered droop law. To achieve voltage regulation with reduced loop interactions, the PI parameters and the filter's pulse are designed according to a two sequential steps procedure based on the (Internal Model Control) IMC technique. Simulation studies are finally presented to demonstrate that the proposed design method achieves both reduction of the loop interaction and robust voltage control in presence of model parameter uncertainty in the MIMO model.

Surfactants are widely used in the synthesis of nanoparticles, as they have a remarkable ability to direct their growth to obtain well-defined shapes and sizes. However, their post-synthesis removal is a challenge, and the methods used often result in morphological changes that defeat the purpose of the initial controlled growth. The cleaning methods could be classified as thermal or non-thermal. In general, the structure of materials can be better preserved by non-thermal treatments. After the removal of surfactants, the highly active surfaces of nanomaterials may undergo structural reconstruction by exposure to a different environment. Thus, ex situ characterization after air exposure may not reflect the effect of the cleaning methods. In situ characterization is required to better understand the impact of various cleaning procedures. Combining X-ray photoelectron spectroscopy, in situ infrared reflection absorption spectroscopy, and environmental transmission electron microscopy measurements with CO probe experiments, we investigated different surfactant-removal methods to produce clean metallic Pt nanoparticles from surfactant-encapsulated ones. Non-thermal plasmas show the best results. It was demonstrated that both UV-ozone treatment and room temperature O2 plasma treatment lead to the formation of Pt oxides on the surface after the removal of the surfactant. These oxides are reduced to metallic Pt during in situ CO probe experiments. On the other hand, when H2 was used for plasma treatment, the Pt0 oxidation state and nanoparticle size distribution were preserved. In addition, H2 plasma treatment can reduce Pt oxides after O2-based treatments, resulting in metallic nanoparticles with clean surfaces. Thermal reduction in hydrogen leads to carbon species emerging onto nanoparticle surfaces after heating and agglomeration of Pt nanoparticles. Particularly, O2-based thermal treatments result in the formation of aggregates consisting of small nanoparticles. These findings provide a better understanding of the various options for surfactant removal from metal nanoparticles and point toward non-thermal plasmas as the best route if the integrity of the nanoparticle needs to be preserved.

Nonionizing millimeter-waves (MMW) are reported to interact with cells in a variety of ways. Possible mechanisms of the inhibited cell division effect were investigated using 85-105 GHz MMW irradiation within the ICNIRP (International Commission on Non-Ionizing Radiation Protection) non-thermal 20 mW/cm² safety standards. ~1.0 mW/cm² exposure over 5-6 hours treatment on 50 cells/μl samples of Saccharomyces cerevisiae model organism, resulted in 62% growth rate reduction compared to control (sham). The effect was specific for 85-105 GHz range and energy dose and cell density dependent. Irradiation of wild type and Δrad52 (DNA damage repair gene) deletion cells presented no differences of colony growth profiles indicating non-thermal MMW treatment does not cause genetic alterations. Dose versus response relations studied using a standard horn antenna (~1.0 mW/cm²) and compared to that of a compact waveguide (17.17 mW/cm²) for increased power delivery resulted in complete termination of cell division via non-thermal processes supported by temperature rise measurements. Combinations of MMW mediated Structure Resonant Energy Transfer (SRET), membrane modulations eliciting signaling effects, and energetic resonance with biomolecules were indicated to be responsible for the observations reported. Our results provide novel mechanistic insights enabling innovative applications of nonionizing radiation procedures for eliciting targeted biomedical outcomes.

Carotenoid and carotenoid esters profiles of peel, pulp and whole fruit tissues of astringent persimmon (Diospyrus kaki Thunb., var. Rojo Brillante) have been characterized in detail and quantified for the first time. Carotenoids were determined by HPLC-PDA-MS/MS (APCI+), using a reverse phase C30 column. A total of 38 carotenoids were identified and quantified, corresponding to 21 free carotenoids (13 xanthophylls and 8 hydrocarbon carotenes) and a total of 17 carotenoid esters. The qualitative profiles are very similar among tissues, differing only in the carotenoids concentration. The most important identified free xanthophylls were (all-E)-β-cryptoxanthin, (all-E)-antheraxanthin, (all-E)-lutein, (all-E)-zeaxanthin and (all-E)-violaxanthin . Hydrocarbon carotenoids found were (all-E)-β-carotene, (all-E)-α-carotene, (9Z)-β-carotene, (13Z)-β-carotene, (9Z)-α-carotene, and lycopene. The most abundant carotenoid esters were (all-E)-lutein-3-O-palmitate, (all-E)-zeaxanthin myristate, (all-E)-zeaxanthin palmitate and (all-E)-cryptoxanthin laurate. Processing by high pressures produced no regular effect on persimmon carotenoids and pasteurization affected negatively the content of all carotenoids from all studied persimmon tissues. This work will contribute to the development of scientific research about the bioaccessibity and bioavailabity of each individual free or esterified persimmon carotenoids in order to a better understanding of the carotenoid compounds impact in human health.

A superior variant of dried jujube in China is ‘Huizao’ (HZ) jujube. Nonetheless, detailed evaluations of the texture quality of HZ fruits have been the subject of few studies. Texture is a significant indicator of the sensory and processed quality of a fruit. Here, we differentiate and characterize the texture quality of HZ fruits from the four primary producing regions in southern Xinjiang, as well as develop a system for assessing the texture quality of HZ fruits. Furthermore, five texture indices of HZ fruits from 109 plantations were exhaustively evaluated utilizing principal component analysis, Pearson correlation analysis, and hierarchical clustering analysis. Consequently, by the 10th, 30th, 70th, and 90th percentiles, each index was classified into five grades—lower, medium, high, and higher. Correlation investigation indicated strong relationships between the springiness, chewiness, cohesiveness, gumminess, and hardness of HZ fruits. Springiness, hardness, and adhesiveness are essential indicators that influence the texture of HZ fruits. We used clustering analysis to separate the six texture indices into three major categories (hard factor, stick-elastic factor, and adhesive factor), with indices representing hardness, springiness, and adhesiveness, respectively. Furthermore, according to the factor molecules, the texture quality of HZ fruits in the four production areas was evaluated as Bazhou (1.24) > Hotan (0.773) > Kashi (-0.577) > Aksu (-0.852). RDA analysis of six texture quality parameters and 24 climate conditions identified higher mean temperature (TEM) and lower relative humidity (RHU) as the primary factors contributing to the improved texture quality of HZ fruits in Xinjiang. This study identified the texture quality characteristics of HZ fruits in four major producing areas of Southern Xinjiang, and it offered a theoretical foundation for optimizing the dominant producing areas and regional production of HZ varieties in Xinjiang.

Herpes simplex virus type 1 (HSV-1) is a lifelong pathogen characterized by asymptomatic latent infection in the trigeminal ganglia (TG) with periodic outbreaks of cold sores caused by virus reactivation in the TG and subsequent replication in the oral mucosa. While antiviral therapies can provide relief from cold sores, they are unable to eliminate HSV-1. We provide experimental results that highlight non-thermal plasma (NTP) as a new alternative therapy for HSV-1 infection that would resolve cold sores faster and reduce the establishment of latent infection in the TG. Additionally, this study is the first to explore the use of NTP as a therapy that can both treat and prevent human viral infections. We investigated the antiviral effect of NTP using an in vitro model for HSV-1 cold sores, involving the application of NTP from two separate devices to cell-free HSV-1, HSV-1-infected cells, and uninfected cells. We found NTP reduced the infectivity of cell-free HSV-1, reduced viral replication in HSV-1-infected cells, and diminished the susceptibility of uninfected cells to HSV-1 infection. This triad of antiviral mechanisms of action suggest the potential of NTP as a therapeutic agent effective against HSV-1 infection.

Depending on human body conditions and environmental conditions, it is sometimes difficult to conduct subject experiments. In such cases, it is effective to use a thermal manikin. There are few studies that investigate the effect of the non-uniform and asymmetric outdoor thermal environment on the mean skin temperature. The purpose of this study is to clarify the influence of the non-uniform and asymmetric thermal radiation of short-wavelength solar radiation in an outdoor environment on the calculation of the mean skin temperature. The skin temperature of the front of the coronal surface, which was facing the sun and where the body received direct short-wavelength solar radiation, and the skin temperature of the rear of the coronal surface, which was in the shadow and did not receive direct short-wavelength solar radiation were respectively measured. The feet, upper arm, forearm, hand and lower leg, which are susceptible to short-wavelength solar radiation in a standing posture, had a noticeable difference in skin temperature between sites in the sun and in shade. The mean skin temperature of sites facing the sun was significantly higher than the mean skin temperature of those in the shade.

The General equilibrium theory tries to show how and why all free markets tend toward equilibrium in the long run. However, what is meant by equilibrium in this paper is more from a thermodynamical point of view. In order to understand the actual situation, it is necessary to study open systems which are complex. In physics, such a behavior in a complex system can be explain by using Non Equilibrium Thermodynamics. A system is able to self-organize and sustain itself away from equilibrium. Economic systems may fluctuate around a particular point. To sustain it far from the equilibrium state, it needs to degrade more energy and materials. In this study, the energy consumption patterns of Sri Lanka and USA are discussed. The pattern concerning Sri Lanka is close to the model proposed here, whereas the energy consumption pattern of USA is more complicated due to external factors.

Continuous technological progress places significant demands on the materials used in increasingly modern devices. An important parameter is often the long-term thermal resistance of the material. The use of heat-resistant polymer materials worked well in technologically advanced products. An economically justified direction in searching for new materials is the area of polymer nanocomposite materials. It is necessary to appropriately select both the polymer matrix and the nanofillers best able to demonstrate the synergistic effect. A promising area of exploration for such nanocomposites is the use of organosilicon polymers, which results from the unique properties of these polymers related to their structure. This review presents the results of the analysis of the most important literature reports regarding organosilicon polymer nanocomposites with increased thermal resistance. Particular attention was paid to modification methods of silicone nanocomposites focused on the increase of their thermal resistance related to the modification of siloxane molecular structure and by making nanocomposites using inorganic additives, carbon nanomaterials. Attention was also paid to such important issues as the influence of the dispersion of additives in the polymer matrix on the thermal resistance of silicone nanocomposites and the possibility of modifying the polymer matrix and permanently introducing nanofillers thanks to the presence of various reactive groups. The thermal stability mechanism of these nanocomposites was also analysed.

In this study, we primarily assess the relationship between social safeguards and the living standards of local communities in different ecological zones of Ghana. This research aims to assist policymakers and stakeholders to make informed and appropriate decisions when developing social safeguards for emission reductions projects. Principal component analysis was employed to develop a living condition index, after which we generated a second construct based on the number of factors affecting living conditions. The results showed that access to sharecropping, literacy, extension services, financial institutions, a mobile phone network, and markets have significant positive relationships with the living conditions of local communities in Ghana. In addition, 78% of the social safeguards described in Ghana’s REDD+ Strategy, Forest and Wildlife Policy, Benefits Sharing Mechanism, and Forest Plantation Development Strategy are aligned with the determinants of local communities’ living conditions. The findings suggest a need to enforce benefit-sharing mechanism, better forest governance, and tenancy reforms in order to prevent the overexploitation of landowners and avoid elite capture. Furthermore, farmers must be linked to financial institutions in order to obtain credits. Additionally, we must seek to provide local communities with better access to markets and mobile phone networks in a way that allows them to carry out their livelihood activities effectively and efficiently. These measures help to reduce the risk of REDD+ actions and ensure sustainability.

The Macroscopic Mechanical Equilibrium Condition can be shown to be the physical origin of the Equation of State of any material system, then can describe all thermodynamic quasi-equilibrium processes caused by the change of the external temperature and/or mechanical environment. If it cannot be satisfied, the system would be broken.

Introduction: The repertoire of microRNAs (miRNAs) in thyroid carcinomas starts to be elucidated. Among differentiated thyroid carcinomas (DTC), papillary thyroid carcinoma (PTC) is the most common. The assessment of miRNAs expression may contribute to refine the pre-surgical diagnosis, in order to obtain a personalized and more effective treatment of patients. Aims: This study aims to evaluated 1) miRNAs expression in a series of DTC, and the association with the presence of selected genetic mutations, in order to improve diagnosis and predict biologic behavior of DTC/PTC. 2) the reliability of molecular tests in Ultrasound-guided Fine Needle Aspiration Cytology (US-FNAC) for a more precise preoperative diagnosis. Material and methods: This series includes 176 samples (98 cytology samples and 78 formalin-fixed paraffin embedded (FFPE) tissues) obtained from 106 patients submitted to surgery, being 13 benign lesions (controls) and 93 DTCs (cases). The microRNA expression was assessed for miR-146b, miR-221, miR-222, and miR-15a by quantitative reverse transcriptase-polymerase chain reaction (qRT-PCR) and the results were analyzed using the 2- ΔΔCT method, using miR16 as an endogenous control. The discriminative ability of miRNAs expression regarding PTC diagnosis was evaluated using the area under the Receiver Operating Characteristic Curve (AUC). The association of miRNAs expression, clinicopatological features and genetic alterations (BRAF, RAS and TERTp) was evaluated in PTCs. Results/Discussion: All the analyzed miRNAs showed a tendency to be over expressed in DTCs/PTCs when compared with benign lesions, both in cytology and histology samples. In cytology, miRNAs expression levels were higher in malignant than in benign tumors. In histology, corresponding discriminative abilities regarding PTC diagnosis were: miR-146b (AUC0.94, 95%CI 0.87-1), miR-221 (AUC0.79, 95%CI 0.68-0.9), miR-222 (AUC0.76, 95%CI 0.63-0.89) and miR-15a (AUC0.85, 95%CI 0.74-0.97). miR-146b showed 89% sensitivity (se) and 87% specificity (sp); mi-R221 se=68.4, sp=90; miR222 se=73, sp=70, and mi-R15a se=72, sp=80. MicroRNAs were associated with aggressive clinicopathological features and tumor progression in PTCs (p < 0.05), particularly for miR-222. Our data reveals a significant association between higher expression levels of miR-146b, miR-221 and miR-222, with the presence of BRAF mutation (p<0.001), and miR-146b (p=0.016) and miR-221 (p=0.010) with the presence of RAS mutation, suggesting an interplay of these mutations with miRNAs expression. Although this study has a relatively small sample size, over expression of miRNAs in cytology may contribute to a more precise preoperative diagnosis. The miRNAs showed a good discriminative ability in PTC diagnosis. The association between the miRNAs expression profile and genetic alterations results could be useful for an accurate diagnosis of DTCs/PTCs in FNAC.

In this paper, we study the existence of the random -pullback attractor of a non-autonomous local modified stochastic Swift-Hohenberg equation with multiplicative noise in stratonovich sense. It is shown that a random -pullback attractor exists in when its external force has exponential growth. Due to the stochastic term, the estimate are delicate, we overcome this difficulty by using the Ornstein-Uhlenbeck(O-U) transformation and its properties.

The motivation of this work is to investigate experimentally the influence of non-thermal plasma (NTP) application on the reaction kinetics of atmospheric pressure steam gasification of charcoal using a thermostatically controlled drop tube reactor. A gliding-arc generator provides about 1 kW electrical power NTP. For comparison thermal gasification is investigated under comparable flow and specific energy input conditions providing additional heat to the steam. Optical temperature measurement 20 cm flow down of the NTP zone is utilized to characterize the specific enthalpy of the reactive flow. The composition of produced syngas is measured by a gas analyzer and used for the calculation of gas flow rates. The results show a NTP-enhancement on the production of individual syngas components (H2, CO, CH4), especially on hydrogen production by around 39%. The syngas-based carbon conversion and hydrogen release are calculated from the carbon and hydrogen balance between the correspondent content in syngas and in the feedstock. The NTP promoted the carbon conversion and hydrogen release by 25% and 31%, respectively. The first-order reaction kinetics are determined by data-fitting in an Arrhenius diagram. The plasma enhanced the reaction rate coefficients by 27%. Based on experimental results and other literature, possible plasma-induced reactions are proposed.

Frontal Polymerization (FP) is recognized as a polymer synthesis method capable of generating a highly localized and self-propagating exothermic front, considered a more rapid and energy-efficient manufacturing scheme for polymer-based fiber-reinforced composite materials. This study conducts a numerical investigation based on the Finite Element Method into the initiation and propagation of frontal polymerization of acrylamide. Utilizing Differential Scanning Calorimetry (DSC) experiments, the study phenomenologically tests the curing kinetics reactions of acrylamide (AM) in deep eutectic solvent (DES)-based polymerizable systems, thereby establishing a curing kinetics model for the autocatalytic reaction of polyacrylamide. By coupling the heat conduction diffusion equation of the frontal polymerization reaction, the Finite Element Method is employed to solve the reaction-diffusion model, aiming to explore the evolution of temperature and degree of curing during the manufacturing process. The results demonstrate the reliability and accuracy of the nth-order autocatalytic model in the study of curing kinetics for DES-based synthesis, indicating that the front propagation speed of the AM-based FP reaction is influenced by the activation temperature, duration of activation temperature, and initial temperature of the solution. Experimental validation of the polyacrylamide manufacturing through frontal polymerization corroborates the accuracy and reliability of the model predictions, providing a reference for the numerical model study and temperature control in the synthesis of acrylamide composite hydrogels via FP.

Solidification microstructure is formed under high cooling rates and temperature gradients in powder-based additive manufacturing. In this study, a non-equilibrium multi-phase field method (MPFM), which was based on a finite interface dissipation model proposed by Steinbach et. al., coupled with a CALPHAD database was developed for a multicomponent Ni alloy. A qua-si-equilibrium MPFM was also developed for comparison. Two-dimensional equiaxed micro-structural evolution for the Ni (Bal.)–Al–Co–Cr–Mo–Ta–Ti–W–C alloy was performed at various cooling rates. The temperature–γ fraction profiles obtained under 10^5 K/s using non- and qua-si-equilibrium MPFMs were in good agreement with each other. Over 10^6 K/s, the differences between non- and quasi-equilibrium methods grew as the cooling rate increased. The non-equilibrium solidification was strengthened over a cooling rate of 10^6 K/s. Colum-nar-solidification microstructural evolution was performed under cooling rates from 5×10^5 K/s to 1×10^7 K/s at various temperature gradient values under the constant interface velocity (0.1 m/s). The results showed that as the cooling rate increased, the cell space decreased in both methods, and the non-equilibrium MPFM agreed well with experimental measurements. Our results show that the non-equilibrium MPFM can simulate solidification microstructure in powder bed fusion additive manufacturing.

The combination of encryption and digital watermarking technologies is a trend to achieve full lifecycle data protection. Recently, reversible data hiding in encrypted domain (RDHED) has greatly aroused the interests of many scholars. But the fixed order of first encryption and then watermarking makes this kind of algorithms unsuitable to many applications. Commutative encryption and watermarking (CEW) technology realizes the flexible combination of encryption and watermarking, and suits more applications. However, most existing CEW schemes for vector maps are not reversible and unsuitable to high precision maps. To solve this problem, here we propose a commutative encryption and reversible watermarking (CERW) algorithm for vector maps based on virtual coordinates which are uniformly distributed on the number axis. The CERW algorithm consists of virtual interval step based encryption scheme and coordinate difference based reversible watermarking scheme. In the encryption scheme, the map coordinates are moved randomly by multiples of virtual interval step defined as distance between two adjacent virtual coordinates. In the reversible watermarking scheme, difference expansion (DE) technique is used to embed the watermark bit into the coordinate difference computed based on the relative position of a map coordinate in a virtual interval. Since the relative position of a map coordinate in a virtual interval keeps unchanged during the coordinate scrambling encryption process, the watermarking operation and the encryption operation don’t interfere with each other and the commutativity between encryption and watermarking achieves. Results show that: proposed method has high security, high capacity and good invisibility. In addition, the algorithm is not only applicable to polyline and polygon vector data, but also can be applied to sparsely distributed point data which the traditional DE watermarking algorithm often fails to watermark.

In an era marked by swift technological progress, the pivotal role of Artificial Intelligence (AI) is increasingly evident across various sectors, including local governments. These governmental bodies are progressively leveraging AI technologies to enhance service delivery to their communities, ranging from simple task automation to more complicated engineering endeavours. While more and more local governments are adopting AI, it is imperative to understand the functions, implications, and consequences of AI. Despite the growing importance of this domain, a significant gap persists within the scholarly discourse. This study strives to bridge this void by exploring the applications of AI technologies within the context of local government service provision and using this inquiry to generate lessons and best practices for similar smart city initiatives. Through a comprehensive grey literature review, we analysed 262 real-world AI implementations across 170 local governments worldwide. The findings underscore several key points: (a) There has been a consistent upward trajectory in the adoption of AI by local governments over the last decade; (b) Local governments from China, the US, and the UK are at the forefront of AI adoption; (c) Among local government AI technologies, Natural Language Processing and Robotic Process Automation emerge as the most prevalent ones; (d) Local governments primarily deploy AI across 28 distinct services; (e) Information management, back-office work, and transportation and traffic management are leading domains in terms of AI adoption. This study enriches the extant body of knowledge by providing an overview of existing AI applications within the sphere of local governance. It offers insights for smart city policymakers and decision-makers considering the adoption, expansion, or refinement of AI technologies in urban service provision. Additionally, it underscores the importance of using these insights to guide the successful integration and optimisation of AI in future smart city projects, ensuring they meet the evolving needs of communities.

This study investigates the impacts of climate change policies on businesses across various sectors, aiming to understand how these regulations affect operational, financial, and strategic aspects of business management. Utilizing a mixed-methods approach, data was collected from 500 businesses through surveys and interviews, encompassing a wide range of industries, sizes, and geographic locations. The findings reveal a complex landscape where 30% of businesses report positive impacts, primarily in the renewable energy and technology sectors, citing increased demand for green products and improvements in energy efficiency. Conversely, 45% of businesses, especially from manufacturing and agriculture, experience negative impacts, including increased operational costs and regulatory compliance challenges. Notwithstanding, a significant majority of businesses are committed to enhancing their sustainability practices, viewing climate change policies as an opportunity for innovation and long-term growth. The study highlights the nuanced effects of climate change policies, emphasizing the need for sector-specific support measures to alleviate financial and operational burdens on negatively impacted businesses. Moreover, it points to a broader shift towards sustainability within the business community, suggesting that climate policies, despite their varied impacts, are driving significant changes in business strategies towards environmental stewardship.

Anaerobic digestion is a biological process that transforms high-strength organic effluents into biogas with multiple benefits. However, concurrent with organics' biological transformation, a liquid phase with a high solid content is also derived from this process. Valorizing this fraction is not an easy task if an agronomic application cannot be considered as a suitable option. The thermal valorization of this fraction allows for energy extraction, but also gives rise to additional capital investment and increases the energy demand of the global process. In addition, the thermal treatment of digestate has to deal with a mineralized material. The changes in organic matter due to anaerobic stabilization were studied in the present manuscript, by evaluating the thermal behavior of samples, activation energy and organic transformation using FTIR spectroscopy. Digested samples of a mixture composed of manure and glycerin (5% v/v) were studied. The stabilization caused a dramatic decrease in aliphatic compounds, greatly increasing the mineral content of the sample. Thermal valorization of digestates must consider the lower energy content and more complex structure of these materials, with higher content of lignin and protein-type compounds.

Cybersecurity is a crucial concern for local governments, as they serve as the primary interface between public and government services, managing sensitive data and critical infrastructure. While technical safeguards are integral to cybersecurity, the role of well-structured policy is equally important, as it provides structured guidance to translate technical requirements into actionable protocols. This study reviews local governments’ cybersecurity policies to provide a comprehensive assessment of how these policies align with NIST CSF, which is a widely adopted and commonly used cybersecurity assessment framework. The review offers local governments a mirror to reflect on their cybersecurity stance, identifying potential vulnerabilities and areas needing urgent attention. The study further extends to developing a cybersecurity policy framework, which local governments can use as a strategic tool. It provides valuable information on crucial cybersecurity elements that local governments must incorporate into their policies to protect confidential data and critical infrastructure.

This study demonstrates a global, non-parametric, non-iterative optimization of time-mean value of a kind of index vibrated by time-varying forcing. It is based on the fact that the (steady) forced vibration of non-autonomous ordinary differential equation systems is well approximated by an analytical solution when the amplitude of forcing is sufficiently small and its base state without forcing is linearly stable and steady. It is applied to optimize a time-averaged heat-transfer rate on a two-dimensional thermal convection field in a square cavity with horizontal temperature difference, and the globally optimal way of vibrational forcing, i.e. the globally optimal, spatial distribution of vibrational heat and vorticity sources, is first obtained. The maximized vibrational thermal convection corresponds well to the state of internal gravity wave resonance. In contrast, the minimized thermal convection is weak, keeping the boundary layers on both sidewalls thick.

Abstract. Background: This paper investigates the propagation of behaviorally transmitted traits with negative effect on host fitness. Methods: We analyze equilibrium between genetically transmitted and behaviorally transmitted competing propagators and consider whether a behavioral propagator is linked to reproduction (e.g. vertical culture transmission), or not. We employ combined genetic and behavior-induced fitness components for hosts, while behavioral propagators have replication factors to distinguish from what’s good for the host (fitness). Results: A trait which spreads faster than its marginal host fitness contribution reduces population will establish itself. The often transient nature of laterally transmitted traits may be a defense against accumulation of deleterious traits. Laterally transmitted traits with high spreading rate often do not equalize with genetic traits, spreading outside natural selection of the hosts. Vertical transmission reduces replication rate and allows group selection against deleterious behaviorally transmitted traits. Competing mutually exclusive propagators contribute to inequality and altruism, but compete through adverse fitness since exclusivity assumes low conversion. Conclusion: Behaviorally transmitted traits, in some cases a tremendous advantage, may also be a significant problem in the development of societies.

The Rybczynski theorem describes the trade effect within production analyses between factor endowments and outputs. The Stolper-Samuelson theorem focuses on cost analyses between factor reward and commodity price. This paper examines the trade effect of changes of factor endowments on prices, based on general equilibrium. The study shows that changes of factor endowments cause domestic output changes (the Rybczynski effect), which affect output prices and factor prices (the Stolper-Samuelson effect). It is like a chain of effects that the Rybczynski’s trade effect triggers the Stolper-Samuelson’s trade effect. The analysis of this paper shows that a small increase of a factor endowment of any country rewards another factor and the commodity using the latter factor intensively. It displays a tuneful circle. Trade brings a well-balanced development to the world.

We present a normative methodology, for value-pricing B2B services, using a Nash Equilibrium mechanism. Value is fundamental to any service, yet it has defied a definition. The literature is conspicuously silent on how to define value, but abounds in richly descriptive characterizations. To overcome this deficit, we focus on the financial economics of service-value. We formulate an axiomatic definition and a differential equation that embodies the idea of service-value. We specify a set of value axioms and multidisciplinary postulates that coherently form our service-value constructs. Value-pricing is challenging. It is natural that providers desire a high price and customers want a low price. Realistically, both will agree on a win-win price. To uncover this price, we specify an algorithm to reveal the Nash Equilibrium. Once agreed, it validates providers’ and customers’ commitments, and payment obligations. Service value is cocreated by both provider and customer. For a reciprocal process, its treatment is remarkably asymmetric favoring the customer. We argue that one-sided descriptions of value-in-use and value-proposition are limiting mental models. We propose the additional ideas of value-from-use and value-supposition to strengthen the conceptual symmetry of cocreation. Our work reveals a critical gap in service science, metrology. Metrology, the science of measurements, is absent from service-science. Service-value is silent on the questions of quantities, units, scales, measurement principles and instruments. We argue for a call to action for Service Metrology. We sketch a roadmap of actionable suggestions to get started.

Enhancement of orthodontic tooth movement (OTM) through local administration of biofunctional molecules has become increasingly significant, particularly for adult patients seeking aesthetic and functional improvements. This comprehensive systematic review analyzes the efficacy of various biofunctional molecules in modulating OTM, focusing on the method of administration and its feasibility, especially considering the potential for topical application. A search across multiple databases yielded 36 original articles of experimental human and animal OTM models, which examined biofunctional molecules capable of interfering with the biochemical reactions that cause tooth movement during orthodontic therapy, accelerating the OTM rate through their influence on the bone metabolism (Calcitriol, Prostaglandins, Recombinant human Relaxin, RANKL and RANKL expression plasmid, growth factors, PTH, osteocalcin, vitamin C and E, biocompatible reduced graphene oxide, exogenous thyroxine, sclerostin protein, a specific EP4 agonist (ONO-AE1-329), carrageenan and herbal extracts). The results indicated a variable efficacy in accelerating OTM, with Calcitriol, Prostaglandins (PGE1 and PGE2), RANKL, growth factors and PTH, among others, showing promising outcomes. PGE1, PGE2 and Calcitriol experiments had statistically significant outcomes in both human and animal studies, and, while other molecules underwent only animal testing, they could be validated in the future for human use. Notably, only one of the animal studies explored topical administration, which also suggests a future research direction. This review concluded that while certain biofunctional molecules demonstrated potential for OTM enhancement, the evidence is not definitive. The development of suitable topical formulations for human use could offer a patient-friendly alternative to injections, emphasizing comfort and cost-effectiveness. Future research should focus on overcoming current methodological limitations and advancing translational research to confirm these biomolecules' efficacy and safety in clinical orthodontic practice.

Vegetation has a significant influence on velocity distribution and turbulent energy in a confluence channel. A laboratory measurement with ADV was used to investigate the flow through a Y-shaped confluence channel partially covered with rigid vegetation on its inner bank. In this study, the flow velocities in cases with and without vegetation were measured by the ADV in a Y-shaped confluence channel. The results clearly show that the existence of non-submerged rigid plants has changed the internal flow structure, that the velocity in the non-vegetated area is greater than in the vegetated area, and that there is a large exchange of mass and momentum between the vegetated and non-vegetated areas. The velocity on both sides is significantly reduced when vegetation is present. In the vicinity of tributaries, due to the presence of vegetation, the high-velocity area moved rapidly to the middle of the non-vegetated area, and the secondary flow phenomenon disappeared. In the mainstream, when vegetation was present, circulation disappeared, and the degree of lateral mixing decreased. The presence of vegetation caused a great change in the internal flow structure and made the flow in non-vegetated areas more intense.

Lung cancer (LC) continues to be an important public health problem being the most common form of cancer and a major cause of cancer deaths worldwide. Despite the great bulk of research to identify genetic susceptibility genes by genome-wide association studies, only few loci associated to nicotine dependence have been consistently replicated. Our previously published study in few phenotypically discordant sib-pairs identified a combination of germline truncating mutations in known cancer susceptibility genes in never smoker early-onset LC patient does not present in their healthy sib. These results firstly demonstrated the presence of an oligogenic combination of disrupted cancer predisposing genes in non-smokers patients, giving experimental support to a model of a “private genetic epidemiology”. Here, we used a combination of whole-exome and RNA sequencing coupled with a discordant sib’s model in a novel cohort of pairs of never-smokers early-onset LC patients and in their healthy sibs used as controls. We selected rare germline variants predicted as deleterious by CADD and SVM bio-informatics tools and absent in the healthy sib. Overall, we identified an average of 200 variants per patient, about 10 of which in cancer predisposing genes. In most of them, RNA sequencing data reinforced the pathogenic role of the identified variants showing: i) downregulation in LC tissue (indicating “second hit” in tumor suppressor genes); ii) upregulation in cancer tissue (likely oncogene); iii) downregulation in both normal and cancer tissue (indicating transcript instability). The combination of the two techniques demonstrates that each patient has an average of six (with a range from four to eight) private mutations with functional effect in tumor predisposing genes. The presence of a unique combination of disrupting events in the affected subjects may explain the absence of familial clustering of non-small cell lung cancer. In conclusion, these findings indicate that each patient has his/her own “predisposing signature” to cancer development and suggest the use of personalized therapeutic strategies in lung cancer.

The focus of this work lies in the construction of monitoring system designed in the form of a patch using a long-lasting potentiometric electrolyte concentration sensor from metal electrodes, in a galvanic cell configuration Mg(s)|NaCl(aq)|Cu(s). Initially, a mathematical analysis was conducted on the expected sensor output through the Nernst equation. The experimental phase involved conducting controlled tests in the laboratory using various molar concentrations of sodium chloride (NaCl) in aqueous solution. Results showed that the electrolyte sensor allows for monitoring electrolyte levels in NaCl in the range of 0.02 to 1 M/L, with electrode lifespan exceeding 10 days. On the other hand, when patch is using human sweat during controlled exercise routines, it showed the sensor's capability for monitoring changes in the subjects' hydration levels in real time. The sensor output potential is greater than 1.7 volts when the sensor electrodes are in contact with human sweat, which is equivalent to measuring molar concentrations at normal hydration and moderately high hydration levels. Sensor results indicate that the system can function in a self-powered manner without external batteries. Additionally, the extended lifespan of its electrodes allows for continuous monitoring of imbalances in the human body, showcasing the system capability for long-term health assessment.

Local polynomial smoother (LPS) is a weighted local least-squares nonparametric method. It provides a local Taylor series fit of the data at any location and can be directly used in a differential equation to provide a numerical scheme. In this article, we introduce this new nonparametric idea based on local polynomial smoother, for acquiring the numerical solution of the Bagley-Torvik fractional-order differential equations. Furthermore, this paper will present a numerical comparison with some methods, such as legendre operational matrix and pseudo-spectral method. The efficiency and accuracy of the LPS method are demonstrated by two numerical examples.

Melioidosis is an endemic infectious disease caused by Burkholderia pseudomallei bacteria, which contaminates soil and water. To better understand the environmental changes that have contributed to melioidosis outbreaks, this study used spatiotemporal analyses to clarify the distribution pattern of melioidosis and the relationship between melioidosis morbidity rate and local environmental indicators (land surface temperature, normalised difference vegetation index, normalised difference water index) and rainfall. A retrospective study was conducted from January 2013 to December 2022, covering data from 219 sub-districts, with each exhibiting varying morbidity rate of melioidosis on a monthly basis. Spatial autocorrelation was determined using local Moran’s I, and the relationship between melioidosis morbidity rate and the environmental indicators was evaluated using geographically weighted Poisson regression. The results revealed clustered spatiotemporal patterns of melioidosis morbidity rate across sub-districts, with hotspots predominantly observed in the northern region. Furthermore, we observed a range of coefficients for the environmental indicators, varying from negative to positive, which provided insights into their relative contributions to melioidosis in each local area and month. These findings highlight the presence of spatial heterogeneity driven by environmental indicators and underscore the importance of public health offices implementing targeted monitoring and surveillance strategies for melioidosis in different locations.

Electrical contacts are important circuit components with diverse industrial applications, and their failure can lead to multiple unwanted effects. Hence, the behavior of electrical contacts is a widely studied topic in scientific literature based on various approaches, tools, and techniques. The present study proposes a numerical modeling and simulation approach based on the Holm contact theory to study the dependence between the electric potential and the temperature within an electrical contact. Structured in 5 sections, the research was conducted using COMSOL Multiphysics software and its solid-state mechanics, electric current, and heat transfer modules in order to highlight contact behavior from mechanical, electrical and thermal points of view: the von Mises stress, contact force, the electric field amplitude, the variation of the electrical potential along the current path, the temperature gradient, and dependence of temperature along the contact elements edges were obtained by simulation and graphically represented. The results are in line with the expectations and with past research that was studied in the literature review.

The keratinocyte carcinomas, basal cell carcinoma (BCC) and cutaneous squamous cell carcinoma (cSCC), are the most common cancers in humans. Recently, an increasing body of literature has investigated the role of miRNAs in keratinocyte carcinoma pathogenesis, progression and their use as therapeutic agents and targets, or biomarkers. However, there is very little consistency in the literature regarding the identity of and/or role of individual miRNAs in cSCC (and to a lesser extent BCC) biology. miRNA analyses that combine clinical evidence with experimental elucidation of targets and functional impact provide far more compelling evidence than studies purely based on clinical findings or bioinformatic analyses. In this study, we review the clinical evidence associated with miRNA dysregulation in KCs assessing the quality of validation evidence provided, identify gaps, and provide recommendations for future studies based on relevant studies that investigated miRNA levels in human cSCC and BCC. Furthermore, we demonstrate how miRNAs contribute to the regulation of a diverse network of cellular functions, and that large-scale changes in tumor cell biology can be attributed to miRNA dysregulation. We highlight the need for further studies investigating the role of miRNAs as communicators between different cell types in the tumor microenvironment. Finally, we explore the clinical benefits of miRNAs as biomarkers of keratinocyte carcinoma prognosis and treatment.

The study addresses the urgent environmental issue of climate change, focusing specifically on the role of local food, which is produced and consumed locally, helps reduce carbon emissions by eliminating the need for long-distance transportation. Through quantitative analysis, this study elucidates the potential benefits in environmental impact achieved through the consumption of local food: the significant reduction in carbon emissions. Specifically, the consumption of local food is found to yield an annual decrease of 2,421,296 tCO2 emissions, representing 2.5% of South Korea’s total greenhouse gas emissions from the transportation sector. This reduction further translates into an estimated economic value of USD 54.23 million (KRW 70.5 billion). This study underscores the potential of local food consumption as a tangible strategy to overcome environmental problems. Moreover, its academic contribution lies in its comprehensive analysis of the economic and empirical impacts of local food consumption on environment. Moving forward, we propose policies such as supporting local food distribution networks, providing public education on local food, fostering the local food industry, and providing incentives to revitalize local food consumption.

The maintenance of traditional agricultural practices in protected small islands is closely linked to the preservation of the land, the protection of natural resources, and the conservation of local traditions. For this purpose, the Tuscan Archipelago National Park promoted the census of ancient horticultural varieties preserved by some farmers on the island of Elba. The survey revealed a deep-rooted historical, cultural, social, and economic link between this germplasm and the island’s territory. A scientific characterization of the landrace under ethnobotanical, morphological, and genetic aspects was carried out. Among these local varieties, two landraces of the Brassica species and three landraces of the Phaseolus species were identified and analyzed in this study. To ascertain their distinguishability and uniqueness, similar varieties were also identified based on morpho-physiological characteristics or territorial proximity and compared with the Elban landraces. Morpho-phenological data were collected, and molecular analyses were carried out using Simple Sequence Repeats (SSR) markers. Ten different SSR loci were considered for the Phaseolus species and nine for the Brassica species. The Tuscan Archipelago landraces showed a high level of internal variability but were clearly distinct from each other and from the analyzed varieties, as shown by AMOVA (Analysis of Molecular Variance). Their distinctness was further highlighted by the UPGMA dendrogram obtained from the genetic distance matrix. The same results were confirmed by Principal Coordinate Analysis (PCoA). This study confirms the peculiarity of the Elban landraces, their biodiversity is a heritage to be safeguarded, which can also be used in future breeding programs. These ancient Elban landraces were allocated to local farmers (most were young farmers) to protect them from extinction and to promote more resilient varieties cultivation compared to commercial hybrids widely spread in the area. Local farmhouses also play a strategic role in safeguarding the germplasm and dissemination of sustainable agricultural practices. There is high demand for ancient Elban landraces, this has led to the development of a new local economy balanced between agricultural tradition and innovation.

Surface initiated atom transfer radical polymerization (SI-ATRP) is one of the most versatile technique to modify the surface properties of material. Recent developed metal free SI-ATRP makes such technique more widely applicable. Herein photo-induced metal-free SI-ATRP of methacrylates, such as methyl methacrylate, N-isopropanyl acrylamide, and N,N- dimethylaminoethyl methacrylate, on the surface of SBA-15 was reported to fabricate organic-inorganic hybrid materials. SBA-15 based polymeric composite with adjustable graft ratio was obtained. The structure evolution during the SI-ATRP modification of SBA-15 was monitored and verified by FT-IR, XPS, TGA, BET, and TEM. The obtained polymeric composite showed enhanced adsorption ability for the model compound toluene in aqueous. This procedure provides a low cost, ready availability, and facile modification way to synthesize the polymeric composites without the contamination of metal.

Epithelial ovarian cancer (EOC) has not significantly benefited from advances in immunotherapy, mainly because of the lack of well-defined actionable antigen targets. Using proteogenomic analyses of primary EOC tumors, we previously identified 91 aberrantly expressed tumor-specific antigens (TSAs) originating from unmutated genomic sequences. Most of these TSAs derive from non-exonic regions, and their expression results from cancer-specific epigenetic changes. The present study aimed to evaluate the immunogenicity of 48 TSAs selected according to two criteria: presentation by highly prevalent HLA allotypes and expression in a significant fraction of EOC tumors. Using targeted mass spectrometry analyses, we found that pulsing with synthetic TSA peptides leads to a high-level presentation on dendritic cells. TSA abundance correlated with the predicted binding affinity to the HLA allotype. We stimulated naïve CD8 T cells from healthy blood donors with TSA-pulsed dendritic cells and assessed their expansion with two assays: MHC-peptide tetramer staining and TCR Vβ CDR3 sequencing. We report that these TSAs can expand sizeable populations of CD8 T cells and, therefore, represent attractive targets for EOC immunotherapy.

Aflatoxin M1 (AFM1), a carcinogenic toxin, mainly contaminates cow milk and poses significant challenges to the dairy industry and, thereby, public health in most tropical countries, including Ethiopia. This study aimed to investigate the prevalence and level of AFM1 in raw cow milk collected from Specialized Dairy Farms and Milk Vendors in three Urban Centers: Chiro town, Dire Dawa, and Harar cities in Eastern Ethiopia. 180 milk samples were collected from two major Milk Sources: Specialized Dairy Farms (N=90) and Milk Vendors (N=90) using a simple random sampling technique. AFM1 was analyzed using high-performance liquid chromatography. The study revealed that, 63.9% (115/810) prevalence and 0.179±0.48µg/L mean of AFM1 level in milk, which 39.13% and 26.08% exceed the tolerable limits of EU and FDA respectively. A 40.0% prevalence and 0.344±0.72µg/L average of AFM1 in the milk from Dire Dawa city was significantly higher than the samples from other Urban Centers. However, 30.43% and 29.57% prevalence as well as 0.055±±0.13µg/L and 0.140±0.33µg/L average of AFM1 in milk from Chiro town and Harar city, respectively were not significant. Furthermore, milk samples from Dairy Farms revealed a higher prevalence (57.39%) and level (0.252±0.64µg/L) of AFM1 than Milk Vendors, with a prevalence of 42.61% and an average of 0.107±0.21µg/L. Therefore, this study concludes that substantial milk samples were contaminated by AFM1 and urges the need to enhance farmers' awareness on mitigation.