This article introduces simulations of theoretical material with controlled properties for the evaluation of the effect of key parameters, as volumetric fractions, elastic properties of each phase and transition zone on the effective dynamic elastic modulus (Ed). The accuracy level of classical homogenization models was checked regarding the prediction of Ed. Numerical simulations were performed with finite element method (FEM) for evaluations of the natural frequencies and their correlation with Ed, through frequency equations. An acoustic test validated the numerical results and obtained the elastic modulus of concretes and mortars at 0.3, 0.5 and 0.7 water-cement ratios (w/c). Hirsch calibrated according to the numerical simulation (x = 0.27) exhibited a realistic behavior for concretes of w/c = 0.3 and 0.5, with 5% error. Nevertheless, for w/c = 0.7, Ed approached Reuss model, similarly to theoretical triphasic materials. Hashin-Shtrikman bounds is not perfectly applied to theoretical biphasic materials under dynamic situations.

If given the correct remotely sensed information, machine learning can accurately describe soil moisture conditions in a heterogeneous region at the large scale based on soil moisture readings at the small scale through rule transference across scale. This paper reviews an approach to increase soil moisture resolution over a sample region over Australia using the Soil Moisture Active Passive (SMAP) sensor and Landsat 8 only and a validation experiment using Sentinal-2 and the Advanced Microwave Scanning Radiometer (AMSR-E) over Nevada. This approach uses an inductive localized approach, replacing the need to obtain a deterministic model in favor of a learning model. This model is adaptable to heterogeneous conditions within a single scene unlike traditional polynomial fitting models and has fixed variables unlike most learning models. For the purposes of this analysis, the SMAP 36 km soil moisture product is considered fully valid and accurate. Landsat bands coinciding in collection date with a SMAP capture are down sampled to match the resolution of the SMAP product. A series of indices describing the Soil-Vegetation-Atmosphere Triangle (SVAT) relationship are then produced, including two novel variables, using the down sampled Landsat bands. These indices are then related to the local coincident SMAP values to identify a series of rules or trees to identify the local rules defining the relationship between soil moisture and the indices. The defined rules are then applied to the Landsat image in the native Landsat resolution to determine local soil moisture. Ground truth comparison is done via a series of grids using point soil moisture samples and air-borne L-band Multibeam Radiometer (PLMR) observations done under the SMAPEx-5 campaign. This paper uses a random forest due to its highly accurate learning against local ground truth data yet easily understandable rules. The predictive power of the inferred learning soil moisture algorithm did well with a mean absolute error of 0.054 over an airborne L-band retrieved surface over the same region.

In this paper, we demonstrate a method of measuring the flexural elastic modulus of ceramics at an intermediate (~millimeter) scale, at high temperatures. We used a picosecond laser to precisely cut micro-beams from the location of interest in a bulk ceramic. They had a cross-section of approximately 100 μm × 300 μm, and a length of ~1 cm. They were then tested in a thermal-mechanical analyzer at room temperature, 500°C, 800°C, and 1100°C using the four-point flexural testing method. We compared the elastic moduli of high-purity Al2O3 and AlN measured by our method with the reported values in the literature and found that the difference was less than 5% for both materials. This paper provides a new and accurate method of characterizing the high-temperature elastic modulus of miniature samples extracted from representative/selected areas of bulk materials.

This research is completed in development of researches devoted to relations between elastic modulus (MoE) and thermal expansivity (CTe) of different materials. This study experimentally confirmed the relation of MoE and CTe for thermosetting polymers and FRPs both under normal and heating temperatures. As the thermosetting polymers, the epoxy compositions were used and glass fiber and mineral additives for FRP. The experiment was based on dilatometric and elastic deformations’ testing. Also, the relaxation model of MoE/CTe was proposed, that is based on physical properties of polymers’ supramolecular structures. The comparative analyzing of MoE/CTes’ different models is done. The most accurate models are determined, and the relaxation model has demonstrated the high accuracy.

The article presents the results of studies aimed to identify the effect of foliar treatments of winter wheat, sugar beets and soybeans with mineral and bioorganic fertilizers. Their positive effect on increasing the concentration of mineral forms of nitrogen in soil was revealed. The crop types have a greater influence on the size of nitrous oxide emissions: in winter wheat crops - 679 µg/m3, soybeans - 637.2 µg/m3, sugar beets - 576.8 µg/m3. The amounts of nitrous oxide emissions were lower in the variants without the use of phosphorus-potassium fertilizers. The Ruter AA fertilizer showed the greatest efficiency on winter wheat crops - 42.7 c/ha. Soybean grain yield of 44.2 c/ha was also achieved by using Ruter AA, as well as Geo-humate together with phosphorus-potassium fertilizers. On the background of the actual supply of phosphorus and potassium, maximum yield was obtained when using N30 on the leaf - 39.3 c/ha. Foliar feeding ensured a yield of sugar beet root crops of up to 67.1-77.4 c/ha on the backdrop of the application of phosphorus-potassium fertilizers with the advantage of using Amino turbo. The largest yield of sugar beet roots without use of mineral phosphorus and potassium was ensured by N30 treatment of the leaf in the phases of 4-6 and 8 leaves - 63.2 t/ha. Of the organo-mineral fertilizers and biostimulants, the best result was shown by the use of Ruter A - 62.6 t/ha. We believe that foliar feeding of crops can be a sustainable farming method that can increase crop yields and reduce N2O emissions.

TiNbZrTa alloys are promising for multidisciplinary applications, such as refractory and biomedical purposes due to their high thermal stability and non-toxicity. Hardness and elastic modulus are among the key features for their adequate industrial applications. The influence of porosity and Ti/Ta ratio were investigated on TiNbZrTa alloys produced by three different processing routes, i.e., (i) blend element and posterior press and sintering (BE + P&S), (ii) mechanical alloying with press and sintering (MA + P&S), and (iii) arc melting and casting. Atomic diffusion was improved during processing, resulting in lower porosity in the following order: casting < MA + P&S < BE + P&S. Ta offered limited atomic diffusion due to its high melting point compared to other constituent elements. Thus, the total porosity of alloys increased with increasing the Ta contents, i.e., by lowering the Ti/Ta ratio. However, the Ti/Ta ratio did not considerably affect the bonding energy or the elastic modulus. Hardness was increased significantly in dense alloys compared to the porous ones. However, porosity and Ti/Ta ratio did not show a clear trend in hardness among the porous alloys.

Present study on land use land cover analysis and taluka wise combination of cropped area, carried out in Beed district of Maharashtra state in India and studied 11 talukas of the district. Secondary data on land use land cover and area in various crops has been collected, compiled and analyzed from various secondary sources. Simple descriptive statistics used to examine the agricultural land use land cover and J.C. Weaver’s crop combination technique was used for taluka wise analysis of crop combinations and on the basis of highest to smallest area engaged in particular crop, crops have been ranked. The study showed that, in the district as a whole, percentage of uncultivated land other than fallow was about 46 percent as compare to net sown area is only 35 percent in total geographical area (1063855ha) of Beed district. The study further revealed that about 42 percent area engaged in food crops and about 58 percent area occupied by nonfood crops, which includes cereals (25%), cotton (19%), pulses (13%), oilseed (12%), sugarcane (5%) and fruits and vegetables (3%). Results of Weaver’s crop combination technique showed that the Wadwani taluka demarcated as most diversified taluka by means of maximum number (sixteen) of crops combinations with the lowest variance value (14) found in the present investigation. Further, the study revealed that the high crop diversity found in Dharur taluka with eighteen crop combinations and the taluka has given first rank amongst others. To derive the crop diversity ranking, taluka wise maximum to minimum number of crop combinations derived in different talukas and given ranks accordingly. The study concluded that, agricultural land use analysis is essential for solving and optimizing the land use problem, maintaining socio-ecological balance, best utilization of scarce resources. The authors enlightened that the rational use of agricultural land has important for food security and biodiversity which increase the productivity and profitability of the agriculture sector and it indicates the decision making ability of farmers in study area.

The use of chemical pesticides in agriculture contributes to soil, water and air pollution, biodiversity loss and can harm non-target species. The European Commission has already established a Harmonized Risk Indicator to quantify the progress in reducing the risks linked to pesticides. Therefore, there is an increasing need to promote biopesticides or so-called low-risk pesticides (LRP). Extract from Melaleuca alternifolia – tea tree oil (TTO) is known for its antiseptic, antimicrobial, antiviral, antifungal, and anti-inflammatory properties. Tea tree oil has been extensively studied in pest management as well as in the pharmaceutical and cosmetic industry and there are already products based on its active substances on the market. This review focuses on the overall evaluation of tea tree oil in terms of effectiveness and safety as a biopesticide for the first time. The collected data can be an added value for further evaluation of tea tree oil in terms of the authorization extension as a fungicide in 2026.

Recent technological advancements in conservation genetics and genomics have resulted in diverse tools for aiding conservation of species. The precision and resolution of high throughput sequencing technologies provide valuable insights to aid conservation decisions, but these technologies are often financially unfeasible or unavailable in resource constrained countries. Inter-Simple Sequence Repeat (ISSR) markers, when combined with sensitive automated detection systems, provide a simple, cheap means to investigate genetic diversity and discriminate closely related species. Here we apply this technology to assess genetic diversity and taxonomic delimitation in the Encephalartos eugene-maraisii species complex, a highly threatened, taxonomically dubious group of cycads in South Africa. Our analyses support taxonomic singularity of E. dyerianus, E. dolomiticus and E. eugene-maraisii. Relationships between E. nubimontanus and E. cupidus remain uncertain. E. middelburgensis samples showed no clustering but had poor amplification success. This study demonstrates the suitability of automated ISSR fingerprinting as a method for plant conservation studies, especially in resource-constrained countries, and we make recommendations as to how this methodology can be effectively implemented.

In this paper, an upper bound of the longitudinal elastic modulus of unidirectional fibrous composites is proposed according to strength of materials approach, on the premise that the fiber is much stiffer than the matrix. In the mathematical derivations, the concept of boundary interphase between fiber and matrix was also taken into account and the main objective of this work is the attainment of an upper bound for the interphase stiffness with respect to fiber concentration by volume. The novel element here is that the authors have not taken into consideration any specific variation law to approximate the interphase modulus. The theoretical results arising from the proposed formula were compared with those obtained from some reliable theoretical models as well as with experimental data found in the literature, and a satisfactory agreement was observed.

In view of the fact that the field monitoring information can more intuitively and accurately reflect the stability state of slopes, this paper takes the warning threshold of slope deformation rate monitoring as the slope stability evaluation standard, and puts forward a method for solving the safety coefficient of rocky slopes. The discrete element method 3DEC, which is suitable for rocky slopes, is selected as the numerical calculation tool, and the convergence criterion of its strength reduction method is modified to the slope deformation rate threshold, and the method is realized by the bifurcation method through its built-in FISH programming language. The results of the classical case show that, by selecting the slope deformation rate threshold in the appropriate interval, the results of this paper's method are very close to those of the finite unit stress method and the limit equilibrium method, which verifies the reliability of this paper's method. Further, the method of this paper is applied to an open-pit mine slope project, based on the slope deformation on-site monitoring data, through the time series prediction method to determine the slope deformation rate warning threshold, using the threshold as an evaluation criterion to solve the slope's coefficient of safety, the calculation results show that: the slope's coefficient of safety in natural working conditions is 1.086, basically stable, suffered from continuous rainfall, the slope body is gradually saturated, the slope's coefficient of safety is reduced to 0.987, the slope's safety is reduced to 0.987. After continuous rainfall and gradual saturation of the slope, the coefficient of safety decreased to 0.987, destabilizing and destroying, which is consistent with the site conditions.

:Peat substrate is made from peat from drained peatlands, which is a limited resource. A realistic estimate is that 50% of the world’s wetlands have been lost. Peat is used in horticulture, especially for the cultivation of vegetables in greenhouses. The consequences of peatland exploitation are an in-crease in the greenhouse effect and a decrease in carbon stocks. Wood fiber can be used as an al-ternative to peat. The chemical properties of the growing media interact and change continuously due to the small volume of the growing media, which is limited by the growing container. This study aims to gain new knowledge on the impact of nutrient changes in the microbial degradation of carbon compounds in wood fiber and mixtures with peat substrate on the content and uptake of nutrients required by plants. Cucumbers (Cucumis sativus L.) variety “Dirigent H” developed in the Netherlands, were cultivated in growing media of peat substrate and wood fiber: (1) peat substrate (PS); (2) wood fiber (WF); (3) wood fiber and peat substrate 50/50 v/v (WF/PS 50/50); (4) wood fiber and peat substrate 25/75 v/v (WF/PS 25/75). The rates of fertilization were the following: (1) con-ventional fertilization (CF); (2) N13; (3) N23; (4) N30. The experiment was carried out in three repli-cations. As the amount of wood fiber increased, the humidity and pH of the growing medium in-creased. Fertilization of cucumbers with different rates of nitrogen influenced the nutrient uptake. Plants grown in 50/50 and 25/75 growing media had the best Cu uptake when fertilized with N23. When the plants grown in the wood fiber media and the 50/50 media were fertilized with N13, N23, and N30, the Mn content in the growing media at the end of the growing season was significantly lower than the Mn content in the media with conventional fertilization. Thus, nitrogen improved the uptake of Mn by plants grown not only in the wood fiber but also in combinations with peat sub-strate. Growing plants in wood fiber and fertilizing them with N13 can result in optimum uptake of micronutrients. The number and mass of cucumber fruits per plant were influenced by the amount of wood fiber in the growing media and the application of nitrogen fertilizer. The highest number of fruits and mass of fruits per plant was obtained significantly higher when cucumbers were grown on WF/PS 50/50 growing media with additional N13 fertilization.

: Greenhouse plants are usually grown in containers filled with growing media. Peat is the main component of the growing media used in greenhouses. However, peat substrate is made from peat from drained peatlands, which is a limited resource. Wood fiber can be an alternative to use as a growing media for controlled-climate crops. The chemical properties of the growing media interact and change continuously due to the small volume of the growing media, which is limited by the vegetative container. Therefore, this study aims to gain new knowledge on the impact of nutrient changes in the microbial degradation of carbon compounds in wood fiber and mixtures with peat substrate on the content and uptake of nutrients required by plants. Cucumbers (Cucumis sativus L.) were cultivated in growing media of peat substrate and wood fiber: (1) peat substrate (PS); (2) wood fiber (WF); (3) wood fiber and peat substrate 50/50 v/v (WF/PS 50/50); (4) wood fiber and peat substrate 25/75 v/v (WF/PS 25/75). The rates of fertilization were the following: (1) conventional fertilization (CF); (2) N13; (3) N23; (4) N30. Fertilization of cucumbers with different rates of nitrogen influenced the nutrient uptake. Plants grown in WF/PS 50/50 and WF/PS 25/75 growing media had the best Cu uptake when fertilized with N23. When the plants grown in the wood fiber media and the 50/50 media were fertilized with N13, N23, and N30, the Mn content in the growing media at the end of the growing season was significantly lower than the Mn content in the media with conventional fertilization. Thus, nitrogen improved the uptake of Mn by plants grown not only in the wood fiber but also in combinations with peat substrate. Growing plants in wood fiber and fertilizing them with N13 can result in optimum uptake of micronutrients. The number and mass of cucumber fruits per plant were influenced by the amount of wood fiber in the growing media and the application of nitrogen fertilizer. The highest number of fruits and mass of fruits per plant was obtained significantly higher when cucumbers were grown on WF/PS 50/50 growing media with additional N13 fertilization.

Revealing the spatial distribution mechanism of the coupling effect between soil water and salt is essential for managing saline-alkali farmland. This study utilized the multifractal method to analyze soil water and salt under varying water content levels in arid saline-alkali farmland. Soil samples were collected on the second (S1), fifth (S2), eighth (S3), eleventh (S4), and fourteenth (S5) days after a rainfall event. The findings showed that a significant decrease in soil water content, contrasting with an increase in soil salt content throughout the soil layers post-rainfall. As water content decreased, the spatial variability of soil water initially increased from S1-3 and then decreased, while the spatial variability of soil salt decreased. The spatial distribution between soil water and salt exhibited a high correlation at S3-4 (with relative water content of soil ranging from 0.52 to 0.75) due to their coupling effect. However, soil salt was unevenly leached by rainfall at high water content levels (S1-2) and precipitated at low water content levels (S5), resulting in low spatial variability correlations between soil water and salt. This study elucidated the coupling process of soil water and salt, identifying their spatiotemporal distribution mechanism in dryland agricultural areas.

Batch and transport experiments were used to investigate the remediation of a loamy sand soil contaminated with Cr(VI) using zero valent iron nanoparticles (nZVI) stabilized by the carboxy methyl cellulose (CMC-nZVI). The effect of pH, ionic strength (IS), and flow rate on the removal efficiency of Cr(VI) were investigated under equilibrium (uniform transport) and non-equilibrium (Two-site sorption) transport using the Hydrus-1D model. The overall removal efficiency ranged from 70 to over 90% based on the chemical characteristics of the CMC-nZVI suspension and the transport conditions. The concentration and pH of the CMC-nZVI suspension had the most significant effect on the removal efficiency and transport of Cr(VI) in the soil. The average removal efficiency of Cr(VI) was increased from 24.1 to 75.5% when the concentration of CMC-nZVI nanoparticles was increased from 10 to 250 mg L-1, mainly because of the increased total surface area at larger particle concentration. Batch experiments showed that removal efficiency of Cr(VI) was much larger under acidic conditions. The average removal efficiency of Cr(VI) reached 90.1 and 60.5 % at pH 5 and 7, respectively. The Two-site sorption model described quite well (r2 = 0.96-0.98) the transport of Cr(VI) in soil as compared to the uniform transport model (r2 = 0.81-0.98). The average retardation of Cr(VI) was 3.51 and 1.61 at pH 5 and 7, respectively, indicating earlier arrival for the breakthrough curves and shorter time to reach maximum relative concentration at lower pH. The Hydrus-1D model has proven to be an efficient tool for assessing the removal of Cr(VI) pollutants, offering innovative, cost-effective, and environmentally friendly remediation methodologies.

Our study aimed to assess sprinkler irrigation's impact on the activity of selected soil enzymes concerning nitrogen metabolism and oxidation-reduction processes in the soil with different doses of inorganic nitrogen fertilizers. The soil Alfisol was sampled from the experimental field of spring barley in the University Research Center in the central part of Poland in the moderate transitory climate during the growing seasons 2015–2017. The index resistance (RS) was derived to recognise the resistance enzymes of drought. In the maturity phase, nitrate reductase activity was at an 18% higher level in irrigated soils and the activity of other enzymes was higher in no-irrigated treatments by 25% in dehydrogenase, 22% in peroxydase 33% in catalase and 17% in urease case. The development stage of barley influenced nitrate reductase activity. Enzymatic activity has been changing in the examined years of the research, depending on the weather conditions. During the maturity stage, the soil's lower ammonium nitrogen content resulted from higher spring barley uptake due to drought stress. Irrigation probably contributes to increased leaching of nitrate in soil. The highest index of resilience was presented in the soil catalase activity.

Phosphite (Phi) has gained attention in agriculture due to its biostimulant effect on crops. This molecule has been found to benefit plant performance by providing protection against pathogens, improving yield and fruit quality, and improving nutrient and water use efficiency. It is still unclear how Phi enhances plant growth and protects against multiple stresses. It has been hypothesized that Phi acts by directly affecting the pathogens and interacting with the plant cellular components and molecular machinery to elicit defense responses. This study delves into elucidating the mechanisms underlying Phi’s beneficial effects on plants, revealing a complex interplay with fundamental signaling pathways. A RNA-seq study of Arabidopsis seedlings under optimal and limiting phosphate conditions helped us unveil Phi’s role in promoting plant growth by activating the expression of genes involved in the biosynthesis and signaling pathways associated with abscisic acid (ABA), salicylic acid (SA), and jasmonic acid (JA). Expression of ABA-related genes, known for their involvement in stress response and development regulation, is triggered by Phi treatment, contributing to enhanced resilience and growth. Simultaneously, the activation of the SA pathway, associated with defense responses, suggests Phi’s potential in bolstering plant immunity. Moreover, Phi influences JA biosynthesis and signaling, which are crucial for defense against herbivores and pathogens, thereby strengthening plants’ defenses. Our findings reveal a multifaceted mechanism through which Phi benefits Arabidopsis development. Understanding its intricate interplay with key signaling pathways opens avenues for leveraging Phi as a strategic tool to enhance plant resilience, immunity, and growth in agricultural and ecological contexts.

This review provides a comprehensive and updated information on chalcones, presenting their sources, methods of identification and properties putting emphasis on applications in agricultural industry. Vast exploitation of synthetic pesticides led to the weed and pest resistance issue, causing economic loss but more importantly health risk due to pesticide overuse. Because one of the aim of the European Green Deal 2030 is the Farm to Fork strategy which targets on reducing by 50% the use of chemical pesticides by 2030, and push towards natural pesticides which are more environmentally friendly and restore natural resources, chalcones and their derivatives seem to fit perfectly. They have herbicidal, fungicidal, bactericidal and antiviral properties. Moreover, chalcones are naturally occurring substances, known for their favorable health effect for years, working on many areas. This review is complementary to the previous ones describing chalcones use in agriculture, updates them but additionally shows methods of detection.

Dielectric elastomers, such as thermoplastic polyurethanes (TPU), are widely used as dielectric layer, emulation layer and substrate of flexible and stretchable devices. To construct capacitors and actuators that work stably upon deformation, it has become an urgent need to investigate the evolution of dielectricity under stress and strain. However, the lack of effective methods for estimating the dielectric constant of elastomers under strain poses a big challenge. This article reports a device for in-situ measuring the dielectric constant of TPU under strain. It is found that upon stretching TPU to a strain of 400%, its dielectric constant decreases from 8.47 to 2.94. In addition, combined Fourier-transform infrared spectroscopy, X-ray scattering technique, and atomic force microscopy have been utilized to characterize the evolution of microstructure under strain. The investigation under tensile strain reveals that a decreased density and average size of polarized hard domains, along with a tendency of the molecular chains to align in parallel with the tensile stress. The evolution of the microstructures results in a reduction of the dielectric constant parallel to the electric field in TPU. Our work provides valuable experimental reference for improving the stability of flexible sensors and actuators based on dielectric elastomers.

Crop production in Afghanistan suffers from limited phosphorus (P) availability, which severely hinders national agriculture sustainability. This present study hypothesized that deep fertilizer placement could significantly enhance uptake of immobile P and thus tissue P accumulation and crop yield. A two-year pot experiment growing two maize (Zea mays) hybrid cultivars (Xida-789 and Xida-211) was therefore conducted to test these hypotheses under three contrasting fertilizer placement methods (broadcast, side band, and deep band). In doing so, P concentrations in both maize tissues and soils were compared at 45, 60, and 115 days after sowing (DAS) under nine combinations of nitrogen (N) and P fertilizer rates (kg ha-1: N112P45, N112P60, N112P75, N150P45, N150P60, N150P75, N187P45, N187P60, N187P75). Results have shown that deep band placement significantly increased P uptake efficiency, leading to greater P concentration and accumulation in maize tissues compared to other two fertilization methods. This improved P uptake was attributed to several factors associated with deep placement, including reduced P fixation, enhanced root access to P, and moisture availability for P uptake. Additionally, deep band placement combined with higher N application rates (N187 and N150) further enhanced plant P uptake by promoting P availability and utilization mechanisms. Deep band placement also resulted in significantly higher total soil P, Olsen-P, and P use efficiency than broadcast and side band methods, indicating a more efficient P fertilization strategy for maize that can improve growth and yield. This present study also found positive correlations between P concentration in plant organs and soil Olsen-P, highlighting the importance of adequate soil P levels for optimal plant growth. Overall, our results have showed that deep band fertilizer placement emerged as a superior strategy for enhancing P uptake efficiency, utilization, and maize productivity compared to broadcast and side band placement. This approach can potentially optimize P fertilizer utilization, improve maize growth and yield, while minimizing environmental P losses associated with broadcast applications.

The composition simplex (N, P, K, Ca, and Mg) of the leaf is the main scores used by different approaches like the Diagnosis and Recommendation Integrated System and Compositional Nutrient Diagnosis to study the nutrient interactions and balance in plant leaves. However, the application and validation of these concepts to grain composition remains unexplored. Contrary to foliar analysis's early intervention for nutrient deficiency detection and correction, applying this approach to seeds assesses diverse cultivars' potential, enabling anticipation of their adaptation to climate conditions and informed selection for future crops. In the present study, a collected database of more than 924 scores including the grain yield (kg ha-1) and the nutrient composition (mg kg-1) of different corn varieties is used to develop a novel nutrient-based diagnostic approach to identify reliable markers of nutrient imbalance. A 'nutrient signature' model is proposed based on the impact of the environ-mental conditions on the nutrient indices and composition (N, P, K, Ca, and Mg) of the corn grains. The yield threshold used to differentiate between low and high-yielding subpopulations is established at 12.000 kg ha-1and the global nutrient imbalance index (GNII) of 2.2 is determined using the chi-square distribution function and vali-dated by the Cate-Nelson partitioning method, which correlated yield data distribution with the GNII. Therefore, the nutrient compositions were classified into highly balanced (GNII ≤ 1.6), balanced (1.6 < GNII ≤ 2.2), and imbalanced (GNII > 2.2). In addition, we found that the Xgboost model's predictive accuracy for GNII is signif-icantly affected by soil pH, organic matter, and rainfall. These results pave the way for adapted agricultural practices by providing insights into the nutrient dynamics of corn grains under varying environmental conditions.

Maintaining sufficient levels of plant nutrients in the soil and controlling certain heavy metals, which can be toxic to the environment, are critical to ensure sustainable agricultural production. The study aimed to assess the linkage of crop-specific agricultural practices established by farmers in the Kvemo Kartli region (Georgia) with metal accumulation in soils of agricultural lands being subject to influence from polluted irrigation water in the past. In particular, we tried to identify the primary sources of micronutrients, including iron (Fe), copper (Cu), manganese (Mn), nickel (Ni), and zinc (Zn), and toxic elements such as cadmium (Cd) and lead (Pb), and share of the contaminated irrigation water and other factors related to agricultural practices under different land uses, such as intensive and extensive arable farming, vineyards, orchards, and permanent pastures having the least disturbed soil. Based on principal component analysis, five primary sources were identified and categorized according to farmers' interviews and previous studies conducted in the region. The results showed that increased concertation of plant-available Cu, Zn, Cd and Pb were mainly associated with irrigation water and intensive use of fungicides; Fe, Mn, and Ni were closely linked to several factors, such as the mineralogical composition of soils, mineral and organic fertilizers inputs, and atmospheric deposition from diffuse sources, where exhausts from transport are probably the primary source. During our study, we attempted to differentiate irrigation water inputs from fungicides using simulation based on irrigation pattern and irrigation water quality on the one hand and fungicide application rate and their metal content on the other. The simulation revealed that the intensive application of fungicides, especially in vineyards, is more significant in enriching soils with Cu and Zn than irrigation water. Identification of factorial dependences was supported by statistical analysis and application of a number of contamination assessment methods: Contamination Factor (CF), Pollution Load Index (PLI), single-factor Pollution Index (PI), Nemerow’s comprehensive pollution index (PIN), Enrichment Factor (EF), and Geo-Accumulation Index (Igeo). Applied environmental indices indicate that the soils under the former and existing vineyards are the most enriched with Cu and Zn, highlighting the significance of agricultural practices on heavy metals accumulation in soils of agricultural lands.

Polymer-modified fertilizers (PMFs) with prolonged nutrient release present a promising solution to address the challenges associated with conventional fertilization practices, particularly for sensitive crops such as strawberries. This study investigates the effectiveness of biodegradable PMFs in maintaining nutrient availability at optimal levels while minimizing root burn and nutrient losses. A factorial field experiment was conducted to evaluate the impact of varying concentrations of polyvinyl alcohol (PVA) on the nutrient release rates from complex NPK fertilizer and monoammonium phosphate, as well as their subsequent effects on strawberry yield and soil properties. Results indicate that polymer modifications significantly slow down nutrient release, leading to prolonged nutrient retention in the soil at salt levels that are optimal for maximizing yield while remaining low enough to prevent the risk of root burn. Consequently, the application of PMFs not only enhances strawberry yield but also promotes healthier plant growth by ensuring a steady supply of nutrients throughout the growing season without inducing stress. The findings underscore the potential of biodegradable polymers to optimize fertilizer efficiency, reduce environmental impacts, and support sustainable agricultural practices. This research provides valuable insights into the development of more effective fertilization strategies for strawberry cultivation and other sensitive crops using PMFs.

This study examines the Soil Organic Carbon (SOC) within Greek croplands, offering a comprehensive understanding of its dynamics. SOC, a cornerstone in soil health, nutrient cycling, and global carbon dynamics, assumes critical significance in sustainable agriculture and climate change mitigation. Drawing on diverse soil properties, including pH, soil texture as well as different drainage and slope categories, the research explores the nuanced relationships shaping SOC dynamics in the diverse agroecological landscape of Greece. The investigation transcends local boundaries, emphasizing SOC's global role in climate change mitigation by sequestering carbon dioxide. Two maps were used as data sources: 1) SOC stock baseline map (2010) by JRC, 2) SOC stock map (2021) by the Institute of Soil and Water Resources, Hellenic Agricultural Organization – DIMITRA in collaboration with FAO. Greek croplands emerge as a mosaic of agroecological diversity, where anthropogenic activities wield transformative influences on SOC stock, demanding a delicate balance between agricultural productivity and soil health. The study unveils the influence of Soil Order, weaving a tapestry of SOC variability. Microscopic factors, from soil texture to cation exchange capacity, further shape SOC dynamics, emphasizing the role of clayey soils and coarse materials in carbon retention. Although soil organic carbon decreased from 2010 to 2021 the degree of carbon loss varied. This scientific endeavor synthesizes existing knowledge and unveils novel insights, offering a narrative woven from diverse soil properties. The findings contribute valuable insights for sustainable land management practices and climate change mitigation strategies, underscoring the importance of region-specific approaches in addressing global challenges.

The article focusses on detecting the unbalance of a mechanical component in the electric drive system of a two-mass servomechanism with a PMSM motor, which is connected to the load via a long, flexible shaft. In the example analysed, the degree of unbalance was determined using the reference current signal from the speed controller of the FOC control system. The authors pre-sented a two-mass model with an unbalanced mechanical system. The STFT transform was used to analyse the symptoms of unbalance and an artificial neural network MLP was used for system state inference. The effectiveness of the presented analysis, based on the reference current signal from the sensor embedded in the control system, was experimentally confirmed.

Elastic properties of materials and their changes with temperature are important for their applications in engineering. A study on the influence of phase composition of AISI 4130 alloy on Young's modulus (Ed), shear modulus (Gd), and damping (Q-1) was carried out by Impulse Excitation Technique (IET). The material characterization was carried out using confocal microscopy, XRD, MET, HV, and dilatometry. A stable structure, composed of ferrite (BCC) and pearlite (α-Fe+Fe3C), was obtained by annealing. Metastable structure of martensite (BCT) was obtained by quenching. The Ed, Gd, and Q-1 were measured, varying the temperature from RT to 900 °C. The values of Ed and Gd, at RT, were determined as 201.5 and 79.2 GPa (annealed), and 190.13 and 76.5 GPa (quenched), respectively. In the annealed steel, the values Ed and Gd decrease linearly on heating up to 650 °C, with the thermal expansion. In the quenched steel, weak changes in the dilatometric curve, Ed, Gd, and Q-1, in the range of 350-450 °C, indicated decompositions of the martensitic phase. Sharp decrease in the moduli and high peak of Q-1, was observed for both samples around 650-900 °C, revealing low lattice elastic stability of the phases during transformations α(BCC)+Fe3C↔γ(FCC).

Reservoirs created by damming rivers significantly modify the environment and problems may arise: the storage of nutrients and organic matter in reservoirs often leads to decreased water quality due to eutrophication. Reservoirs built on lowland rivers are exposed to significant nutrient loads, often leading to eutrophication. In this article, the Sulejów Reservoir, in Central Poland, was the subject of the research, which focused on the use of Sentinel-2 remote sensing data to detect phytoplankton blooms, and on understanding the pattern of wind-driven surface currents using the CCHE2D model (a depth-averaged hydrodynamic model). The calculation of the total phosphorus load has shown that the reservoir mainly acts as nutrient storage. Still, during the low flow and intensive phytoplankton bloom, it can be a source of nutrients. The distribution of phytoplankton bloom on the Sulejów Reservoir was documented using eight Sentinel-2 satellite images from the vegetation season of 2020 and the Normalized Difference Chlorophyll Index (NDCl). Coupling remote sensing data and numerical modelling helps to interpret the hydrodynamic model results and understand nutrients and sediment dynamics within the reservoir. Hydrodynamic modelling combined with remote sensing data can be a valuable tool for selecting appropriate locations for water quality measurements at monitoring stations.

The potato is the most important non-cereal food crop, and thus improving potato growth and yield is in the focus of agricultural researchers and practitioners worldwide. Several studies reported beneficial effects of silicon (Si) fertilization on potato performance, although plant species from the family Solanaceae are generally considered as non-Si-accumulating. We used results from two field experiments in the temperate zone to gain insight into silica accumulation in potato plants as well as corresponding long-term potato yield performance. We found relatively low Si contents in potato leaves and roots (up to 0.08% and 0.3% in the dry mass, respectively) and negligible Si contents in potato tuber skin and tuber flesh for plants grown in soils with different concentrations of plant available Si (field experiment 1). Moreover, potato yield was not correlated to plant available Si concentrations in soils in the long-term (1965-2015, field experiment 2). Based on our results we ascribe the beneficial effects of Si fertilization on potato growth and yield performance reported in previous studies mainly to antifungal/osmotic effects of foliar-applied Si fertilizers and to changes in physicochemical soil properties (e.g., enhanced phosphorus availability and water holding capacity) caused by soil-applied Si fertilizers.

The study of localized surface plasmons (LSPs) in nanoscale structures is an essential step towards identifying optimal plasmonic modes that can facilitate robust optomechanical coupling and deepen our understanding of light-matter interactions at the nanoscale. This paper investigates numerically, using the finite element method, LSPs modes in a design comprising two coupled nano-ridges deposited on a gold layer, with an interposing polymer spacer layer. Such a structure, usually referred to as particles-on-mirror, shows exquisite optical properties at the nanoscale. We first examine the LSPs modes of a single nano-ridge through the analysis of its scattering cross-section in the visible and infrared range. To enhance the plasmonic response, a thin polymer layer is placed at the middle of the ridge, which introduces additional LSPs modes confined within the former. Then, we extend the analysis to the dimer configuration, which exhibits more complex and enhanced plasmonic behavior compared to a single nano-ridge. In particular, the dimer configuration yields LSPs resonances with a quality factor enhancement of approximately threefold relative to single nano-ridge. Furthermore, the presence of the polymer layer within the ridges significantly improves plasmon field localization and quality factor. These findings underscore the potential of nano-ridge-based structures in advancing optomechanical coupling and plasmon-phonon interaction studies, offering valuable insights for the development of high-performance acousto-plasmonic devices. In particular, the proposed device could help significantly improve the design of nano-acousto-optic modulators operating in the visible or in the near infrared, that require enhanced light-photon coupling rate.

This paper revisits a classic problem in physics - Hertz elastic dynamics of two colliding elastic spheres. This study obtains impact period in terms of hypergeometric function and successfully combines Deresiewicz's three segmental solutions into one single solution. Our numerical investigation confirms that Deresiewicz's inversion is a good approximation. As an essential part of this study, a general Maple code is provided.

The impact of antecedent soil moisture content on soil erosion is a complicated phenomenon, which is still under argument with contradictions in research results. Hence, the objective of this study is to investigate the impact of antecedent soil moisture content to soil loss on clay soil by conducting two-year field experiments under natural rainfall on runoff plots with length of 10 meters, width of 3 meters, and uniform slope of 9%. Volumetric soil moisture sensors were used to log soil moisture changes, and soil moisture readings were used along with rainfall records to quantify the antecedent soil moisture conditions for each rainfall event. Results of this study show duration of the effective erosion event outranks the antecedent volumetric soil moisture content. Field study also suggests that accumulative rain falling within 48 hours (Pp48) prior to an effective erosion event strongly correlated with soil loss per Rainfall-Runoff Erosivity Index (Soil Loss / EI30), particularly when the duration of an effective erosion event is either between 3 ~ 7 hours or 10~ 30 hours. Hence, Pp48 can be considered as an alternative to replace antecedent soil moisture content in RUSLE 2’s cover and management factor.

In this paper, the far field and near field optical responses of a gold nanoparticle are studied and simulated numerically. The electromagnetic field was excited by an electric dipole located near one end of the nanorod, which is used to model the emission of a quantum dot. Another excitation method was also simulated in which an incident plane wave is used. The excitation of dark plasmon modes of the gold nanorod is presented. The Poynting equation was solved numerically to study the influence of the gold nanorod on the dipole radiative power. In addition, the extinction cross section of the gold nanoparticle illuminated by the incident plane wave was calculated to estimate the amount of the scattered and absorbed light.

In the Vietnamese Mekong delta, soil quality and crop yield are steadily declining under rice monocultures with three crops per year. The objective of this study was to evaluate the medium-term effects of rotating rice with upland crops and adding organic amendments on rice yield and relate it to soil quality. A field trial with split-plot design including two factors and three replicates was carried out from 2017 to 2020, over the course of nine consecutive cropping seasons. Crop rotations and organic amendments were applied as main-plot and subplot factors, respectively. The rotations were: 1) rice–rice–rice (R–R–R), 2) soybean–rice–rice (So–R–R), and 3) sesame–rice–rice (Se–R–R), while organic amendment treatments included: i) no amendment (NO-AM); ii) compost of rice straw and cow manure (RS+CM), and iii) sugarcane compost (SGC); the composts were applied at a rate of 2.0 t ha-1. The rotation cycle started with the so-called spring–summer (SS), followed by summer–autumn (SA) and ended with the winter–spring (WS) season. Rice yield significantly (P &lt; 0.05) increased by organic amendments after nine growing seasons (2019–2020 WS), with an increment of 5.1% for RS+CM (7.07 ton/ha) and 6.1% for SGC (7.14 ton/ha). Contrary to our expectation, rotations with upland crops did not significantly increase rice yield. Rice yield significantly and positively correlated with an integrated soil quality index SQI (r = 0.86) for the topsoil (0–15 cm), but not for the subsoil (15–30 cm). The increased availability of soil nutrients (Si and marginally also P) and improved soil physical properties probably induced by organic amendments, along with other soil properties under study, cumulatively attributed to enhanced rice yield. Use of a SQI involving several soil quality indicators enables to overall quantify the importance of soil fertility for rice yield versus other factors and it provides an effective means of quantifying the integrated effect of improved management. Moreover, integrating a wide range of soil quality indicators in a SQI ensures its applicability across diverse settings, including different crop rotations and various soil types.

In steel structures, oblique thin steel plates serve as panel zones in structures spanning large spaces (e.g., warehouses and gymnasiums). Considerable research has been conducted on the shear buckling of panels due to seismic loads acting on a structure. Conversely, under snow or wind loads, the panel zone may experience compressive and tensile stresses simultaneously from two directions. Considering the economic preference for thin steel plates, evaluating the elastic critical local buckling stresses in the panel zone under biaxial normal stress may provide essential information to structural engineers. In this study, an elastic buckling analysis based on the energy method is performed to clarify the impact of panel geometry and boundary conditions on the elastic local buckling stresses of oblique panel zones. As confirmed, the buckling stresses derived from the energy method could simulate the local buckling stresses with accuracy comparable to that of finite element analysis, and an engineer-friendly design formula was proposed. Finally, we determined the correlation of the buckling stresses under biaxial stresses and presented a method for evaluating this correlation. Engineers can utilize the provided design equations to more efficiently and accurately calculate buckling loads, facilitating safer and more economical design of structures with oblique plates.

Stage IV grade C localized periodontitis (pre-puberal localized aggressive periodontitis/LPP), an extremely rare form of periodontal disease, occurs in otherwise healthy individuals (no signs of dental plaque/calculus) due a hyper-aggressive auto-immune response to high periodontopathic bacteria levels. Methods: A 4-year-old Caucasian girl with unusual high mobility of temporary lower left canine and localized gingival inflammation was misrecognized by multiple clinicians (initially diagnosed with hypophosphatasia, genetic and metabolic disorders, all turning negative), over a period of 4-6 month, despite initial radiographs showing clear pathognomonic signs. LPP diagnostic was made by the last clinician, but by now the tooth was lost. Similar inflammation signs appeared around the lower temporary right canine. X-ray examination showed similar bone and periodontal loss as previously seen, while periodontopathic bacteria tested highly positive. The patient received both mechanical cleaning and ten days systemic antibiotic treatment (Augmentin and Metronidazole). Results: Two months after, inflammation signs disappeared, with periodontal regeneration radiologically present, and only small periodontopathic bacteria precursors concentrations. Conclusions: Despite initial periodontal loss, an adequate treatment can keep under control an LPP disease. Moreover, bone and periodontal regeneration appears if periodontopathic bacteria scores are kept lower, showing the importance of fast adequate diagnostic and treatment.

The most important plastic resins used for wire coating are Polyvinyl Chloride (PVC), Nylon, Polysulfone and Low-high density polyethylene (LDPE / HDPE). In this article,the coating process is performed using elastic-viscous fluid as a coating material for wire coating in a pressure type coating die. The elastic-viscous fluid is electrically conducted in the presence of an applied magnetic field. The governing non-linear equations are modeled and then solved analytically by utilizing an Adomian decomposition method (ADM). The convergence of the series solution is established. The results are also verified by Optimal Homotopy Asymptotic Method (OHAM). The effect of different emerging parameters such as non-Newtonian parameters α and β, magnetic parameter M and the Brinkman number Br on solutions (velocity and temperature profiles) are discussed through several graphs. Additionally, the current result also compares with the published work already available in the literature.

The paper presents two procedures for creating 3D discrete models of apple using the finite element method (FEM). The study focused on a new Polish apple variety, Chopin at development, ripening, and senescence maturity stages. The analysis of the results allowed for the determination that, depending on the desired outcomes, the parenchymal tissue can be considered as a material with either elastic or elastoplastic properties. Model validation was performed using displacement-force relationships and changes in contact area as a function of loading force obtained from compression tests. Elastoplastic models reflect empirical studies much better. The fit of the elastic models, based on force vs. displacement curves, ranged from 79% to 83%, while the fit of the elastoplastic models to empirical data ranged from 91% to 96%. Elastic models, on the other hand, are well-suited to the modified force vs. displacement curves, which reflect the elastic behavior of apples under compression test. Contour plots of pressures for elastoplastic models align much better with the test results than those for elastic models. 4. Similarly, in the case of contact area values, the elastoplastic models outperformed the elastic models, achieving a fit between 92% and 96%, while the elastic models reached only 82% to 83% compliance.

Kiwifruit (Actinidia chinensis) cultivation is expanding worldwide being China, New Zealand and Italy the major producing countries. Halyomorpha halys, the brown marmorated stink bug, has been raising serious concerns to kiwifruit cultivation both in China and Italy. This study aimed at improving the chemical control efficacy against this pest by comparing two insecticide spray techniques (a conventional ray atomizer and a trumpet-modified atomizer adapted for localized spray application in kiwifruit). In fact, kiwifruit is often grown with a ‘pergola’ training system, which may reduce the effectiveness of insecticide penetration into the canopy. Experiments have been performed in naturally infested orchards of both Actinidia chinensis var. chinensis ‘Jintao’ and A. chinensis var. deliciosa ‘Hayward’ during two consecutive seasons. Furthermore, mesh cages, each containing three H. halys adults, were deployed in the orchards to assess the insects’ mortality at 1, 3, 7 and 10 days after the insecticide application with the two spray techniques. In the cultivar 'Jintao', the two systems performed similarly, while in the cultivar 'Hayward', an overall significantly higher insect mortality was recorded with the trumpet atomizer. The crop damage was also evaluated on both cultivars, simulating the grower insecticide applications with the two spray techniques. At harvest, no difference emerged between the spray techniques, which provided a significantly better protection compared to the untreated control. Further investigations in this direction are needed also considering the restriction of insecticidal active substances ongoing in European Union and the need to maximize the efficacy of the available tools.

Additives for anaerobic digestion (AD) can play a significant role in optimising the process by increasing biogas production, stabilising the system and improving digestate quality. The role of additives largely boils down to: (i) enhancing direct interspecies electron transfer (DIET) between microbial communities, resulting in improved syntrophic interactions and methane production rates (e.g. biochar, magnetite and carbon nanotubes), (ii) adsorption of toxic substances that may inhibit microbial activity (e.g. activated carbon, zeolites), (iii) improving microbial activity and increasing process stability (e.g. cobalt, nickel, iron, selenium), (iv) maintaining optimal pH levels for microbial activity (e.g. magnesium oxide), (v) reducing inhibition (the aforementioned adsorbents and conductive substances), (vi) accelerating the decomposition of complex organic materials into simpler compounds that are more easily digested by microorganisms, thereby increasing the rate of hydrolysis (enzymes, including cellulases, proteases and lipases). Through the aforementioned action, additives can significantly affect AD performance. The function of these materials varies, from enhancing microbial activity to maintaining optimal conditions and protecting the system from inhibitors. The choice of additives should be carefully tailored to the specific needs and conditions of the digester to maximise benefits and ensure sustainability. In light of these considerations, this paper characterizes the most commonly used additives and their combinations based on a comprehensive review of recent scientific publications, including a report on the results of conducted studies. The publication features chapters that describe: carbon-based conductive materials, metal oxide nanomaterials, trace metal and biological additives, including enzymes and microorganisms. It concludes with a chapter summarising reports on various additives and discussing their indications for functional systems with determined properties. A notable advantage of this work is the updated literature data, clear summaries, and a substantive description of the performance of the additives discussed.

This paper is the continuation of a previous study, which highlighted some inconsistencies in the RILEM guidelines for the interpretation of the diagonal compression test. Although improved compared to the ASTM guidelines, in fact, the RILEM guidelines underestimate the state of hydrostatic stress induced by the diagonal compression test at the center of the wallette. The new interpretation of the diagonal compression test proposed in this article shows that the RILEM guidelines actually underestimate both the hydrostatic and the deviatoric stress states at the center of the wallette. The new formulation complies with the linear elastic theory and allows us to use the the diagonal compression test to identify the three elastic coefficients of masonry. In particular, it allows the identification of the Poisson ratio, which instead takes on a conventional value in the RILEM and ASTM guidelines. The difference of one order of magnitude between the conventional and proposed Poisson’s ratio is in agreement with the experimental results on another brittle material, namely concrete. Finally, the new proposal fills the gap between the results provided by the two tests usually performed to identify the shear behavior of masonry: the diagonal compression test and the shear-compression test.

In Ethiopia, farmers have changed cropland to Eucalyptus globulus plantations for construction, fuelwood and economic benefits. However, it has adverse effects on soil properties. The investigation was, therefore, to evaluate the impact of Eucalyptus globulus plantations on soil properties in northwestern Ethiopia. About 30 soil samples were collected from two soil depths (0-20 and 20-40 cm) and three land uses (Eucalyptus globulus plantations, cropland and grazing land) with five replications. Soil properties were analyzed using a two-way analysis of variance (ANOVA). Based on the result, soil properties such as silt particles, moisture content (MC), organic matter (OM), total nitrogen (TN) and cation exchange capacity (CEC) were significantly higher under the soil of Eucalyptus globulus plantations than in cropland and grazing land. Whereas the lower contents of bulk density (BD), soil pH, available phosphorus (AP), electrical conductivity (EC) and exchangeable bases (Ca, Mg, K, and Na) were recorded in Eucalyptus globulus plantations. Besides, clay, BD, MC, pH, EC, CEC, percent base saturation (PBS) and basic cations increased with soil depth while decreasing sand, silt, TP, OM and AP. The basic cations ( Ca, Mg, K), PBS and AP decreased in the soil of the 25-year old Eucalyptus globulus plantation compared to cropland by 38%, 36%, 43 %, 45% and 47% and grazing land by 56%, 60%, 76 %, 60% and 56%, respectively. Therefore, appropriate and effective land use management principles should be implemented in the study area.

In the recent years, tubular nanostructures have been related with immense advances in various fields of science and technology. Considerable research efforts have been centered on the theoretical prediction and manufacturing of non-carbon nanotubes (NTs), which meet modern requirements for the developing of novel devices and systems. In this context, diatomic inorganic nanotubes formed by atoms of elements from the 13th group of the periodic table (B, Al, Ga, In, Tl) and nitrogen (N), have received much research attention. In the present work, the elastic properties of single-walled boron nitride, aluminium nitride, gallium nitride, indium nitride and thallium nitride nanotubes were numerically evaluated using the nanoscale continuum modelling approach (also called molecular structural mechanics). The elastic properties (rigidities, surface Young´s and shear moduli, and Poisson´s ratio) of nitride nanotubes are discussed with respect to the bond length of the corresponding diatomic hexagonal lattice. The results obtained contribute to a better understanding of the mechanical response of nitride compound-based nanotubes, covering a broad range from the well-studied boron nitride NTs to the hypothetical thallium nitride NTs.

The Katerini-Kolindros aquifer system (KKas) is a critical freshwater resource, essential for the local and regional economy. To understand contamination sources, groundwater flow paths, and assess the aquifer's health, an extensive dataset of 751 samples from 113 wells collected between 2010 and 2020 was analyzed using multivariate statistical analysis (MVSA) and hydrogeochemical diagrams. The prevailing water types identified were Ca-HCO₃ and Mg-HCO₃, with mixed water types resulting from various factors affecting groundwater quality. The chemistry of groundwater in the KKas is shown to be affected by ion exchange processes and to a lesser extent by reverse ion exchange processes. No indications of sea-water intrusion have been identified in the water wells monitored. On the other hand, nitrate contamination has been detected in specific water wells spatially associated with urban-type land uses and activities. It is considered that nitrate contamination originates primarily from septic tanks and urban sewage networks or secondarily from fertilization of football pitches, cemeteries or urban waste management practices.

During routine bridge maintenance, edge detection allows the partial condition of the bridge to be viewed. However, many edge detection methods often have unsatisfactory performances when dealing with images with complex backgrounds. Moreover, the processing often involves the manual selection of thresholds, which can result in repeated testing and comparisons. To address these problems in this paper, the wavelet transform modulus maxima method is used to detect the target image, and then the threshold value of the image can be determined automatically according to the OTSU method to remove the pseudo-edges. Thus, the real image edges can be detected. The results show that the information entropy and SSIM of the detection results are the highest when compared with the commonly used Canny and Laplace algorithms, which means that the detection quality is optimal. To more fully illustrate the advantages of the algorithms, images with more complex backgrounds were detected and the processing results of the algorithms in this paper are still optimal. In addition, the automatic selection of thresholds saves the operator’s effort and improves the detection efficiency. Thanks to the combined use of the above two methods, detection quality and efficiency are significantly improved, which has a good application in engineering practice.

A special vibration damper is proposed for material property identification through a scratching process on a vibrating object. This paper presents the design and working principle of a scratching damper based on a scratch test device. A non-contact electromagnetic shaker is used to generate the shaking force for the vibration of the tested object. The required pressure on the scratched material during the scratching process is generated by a compression spring and adjusted by changing the amount of compression of the spring. The proposed damper is designed and tested on extruded aluminum samples for the determination of its Young’s modulus and hardness and validated by using the standard test instruments. Observations of physical dimensions of the scratching tracks are determined by microscope and were utilized to compute the scratching energy factor. Load curves are obtained at different pressure of the scratching process. The hysteresis loop energy during the scratching process of the tested object is measured and used for the determination of material properties of the object. Furthermore, energy conservation law, scratch energy release rate and loop energy release rate are used to determine the Young’s modulus and hardness of the sample. The measurement accuracy of the modulus and hardness of the tested sample is evaluated. The proposed method of material testing has several advantages over the traditional methods such as low cost and high repeatability, and may be used as an alternative to the standard modulus and hardness testers.

Our work is regarding the analysis of land use changes, in the light of “saving soil” against the expansion due to unearned plus value of land: The loss of natural and agricultural surface in front of the expanding urban environment is a critical aspect of unsustainability of urban development, especially in the way it was carried out in the past decades. The measure of the physical transition of land use and characters from a more natural condition of land surface to a new artificial one, joint with a parallel analysis of the increase of land value due to such change is nowadays a major land-policy tool. The interplay of urban economics regulation with planning, reveals new key issues in urban governance and environmental preservation. In this paper it will be shown some experiment about the impact assessment of soil take, related with the seek of valorization of property inside the planning process. Our paper reports as well about the experimental activity carried out inside the MITO Lab of the Polytechnic of Bari, where reports about property values and environmental values have been produced, specially looking at the reality of the Apulia, a southern Italian Region, that is rich of farmlands and coastlines, often invaded by constructions with a severe loss of nature, landscape and ecosystems services.

Wheat is used for making many food products due to its diverse quality profile found among different wheat classes. Since laboratory analysis of these end-use quality traits is costly and time-consuming, genetic dissection of the traits is preferential. This study used a genome-wide association study (GWAS) of 10 end-use quality traits, including kernel protein, flour protein, flour yield, softness equivalence, solvent’s retention capacity, cookie diameter, and top-grain, in soft red winter wheat (SRWW) adapted to US southeast. The GWAS study included 266 SRWW genotypes that were evaluated in two locations over two years (2020-2022). A total of 27,466 single nucleotide markers were used and a total of 80 significant marker-trait associations were identified. There were 13 major effect quantitative trait loci (QTLs) explaining &gt; 10% phenotypic variance out of which 12 were considered as novel. Five of the major effect QTLs were found to be stably expressed across multiple datasets, and four showed associations with multiple traits. Candidate genes were identified for eight of the major-effect QTLs including genes associated with starch biosynthesis and nutritional homeostasis in plants. These findings increase genetic comprehension of these end-use quality traits and could potentially be used for improving the quality of SRWW.

Beetles are by far one of the most successful and diverse insect species. A part of this success is attributed to their elytra which provide various functions such as protection to their bodies from mechanical forces and the harmful environmental factors. In this study, Stag beetle (Lucanus cervus) elytra were first examined for their overall flexural properties and were observed to have a localized shape retaining snap-through mechanism which could play a crucial role in energy absorption, e.g. during battles and falls from heights. The snap-through mechanism was validated using theoretical calculations and also finite element simulations. Elytra were also characterized to examine their puncture and wear resistance. Our results show that elytra resisted puncture up to a force of 1.8±0.4 N and have puncture resistance compared to that of commercially available puncture resistant gloves. The measured values of modulus and hardness of elytra exocuticle were 10.3±0.8 GPa and 0.7±0.1 GPa. Using the hardness to modulus ratio as an indicator of wear resistance, the estimated value was observed to be in the range of wear resistant biological materials. Thus, our study demonstrates different mechanical properties of the stag beetle elytra which can be explored to design shape retaining bio-inspired composites with enhanced puncture and wear resistance.

This study investigates how root environment acidification impacts tea seedlings and the role of magnesium (Mg) in mitigating these effects. We examine varying pH and Mg levels' influence on tea seedlings' resistance to abiotic stress, focusing on antioxidant capacity and nutritional content. In a hydroponic experiment, we varied root pH (3.5, 5.0, 6.5) and Mg concentrations (0.01, 0.4, 0.8 mM), assessing parameters like antioxidant capacity, peroxidative damage, and nutritional content at 1, 7, 15, and 30 days post-treatment. Root environment acidification and Mg deficiency worsened peroxidative damage in tea plant leaves and roots. Increased Mg supplementation enhanced antioxidant enzyme activity, reducing malondialdehyde and mitigating oxidative damage from root environment acid stress. Under acid stress, 0.8 mM Mg significantly increased tea leaf polyphenols, amino acids, and water-soluble extracts. Mg notably boosted chlorophyll content, surpassing lower Mg levels at pH 5. Additionally, Mg reversed root vitality inhibition induced by acid stress, leading to increased nitrogen, potassium, and Mg concentrations in leaves, promoting balanced nutrient absorption. Mg supplementation is crucial for enhancing tea plant antioxidant capacity, alleviating growth inhibition from root environment acid stress, and improving chlorophyll content and root vitality, highlighting Mg's significance in tea cultivation and broader agricultural practices.

Mycoviruses are highly genetically diverse, can significantly change their fungal host’s phenotype, yet, they are generally under-described in genotypic and biological studies. We propose Botrytis cinerea as a model mycovirus system in which to develop a deeper understanding of mycovirus epidemiology including diversity, impact, and the associated cellular biology of the host and virus interaction. Over 100 mycoviruses have been described in this fungal host. B. cinerea is an ideal model fungus for mycovirology as it has highly tractable characteristics – it is easy to culture, has a worldwide distribution, infects a wide range of host plants, can be transformed and gene-edited, and has an existing depth of biological resources including annotated genomes, transcriptomes, and isolates with gene knockouts. Focus on a model system for mycoviruses will enable the research community to address deep research questions that cannot be answered in a non-systematic manner. Since B. cinerea is a major plant pathogen, new insights may have immediate utility as well as creating new knowledge that complements and extends the knowledge of mycovirus interactions in other fungi, alone or with their respective plant hosts. In this review we set out some of the critical steps required to develop B. cinerea as a model mycovirus system and how this may be used in the future.

South Africa (SA) is grappling with a severe food insecurity crisis exacerbated by socioeconomic challenges. This resulted in the Department of Basic Education (DBE) advocating for the establishment of vegetable gardens at schools. However, information on the suitability of the soils in SA for sustainably growing Beetroot is unavailable. This study aimed to assess the suitability of soils for sustainable Beetroot production at various schools in the Kgakotlou circuit. Four Secondary Schools were selected: Mothimako, Madipoane, Klaas Mothapo and Phomolong. A detailed soil survey was carried out to study soils in vegetable gardens. Soil samples were collected for laboratory analysis of physicochemical properties. The soil suitability was evaluated using the physicochemical properties of the soils and optimal soil requirements for Beetroot production. We found various soils in the schools, including Cambisols (Hutton and Nkonkoni), Leptosol (Glenrosa), Plinthosol (Westleigh), and Acrisols (Tshiombo and Tubatse). Portions of the gardens on Hutton and Westleigh soil were moderately suitable (S2), limited by electrical conductivity (EC). Meanwhile, portions of Tshiombo, Tubatse, and Nkonkoni were marginally suitable (S3), limited by pH and EC. Portions on Glenrosa soil at Klaas Mothapo and Phomolong were not suitable (NS) and were limited by shallow depth, soil pH and EC. The results reveal the importance of considering soil suitability before establishing vegetable gardens in school settings. Indexing soil suitability using the physicochemical properties of soil resources for sustainable beetroot production is proposed for schools in the Kgakatlou circuit and other parts of SA.

Water is a fundamental resource for ecosystems, humans, and the development of all economic sectors; it is necessary to identify and evaluate its environmental pressures or impacts. The water footprint (WF) is an appropriate indicator for the consumption of water used to produce a product. The present study uses this tool to evaluate the green and blue water requirements and the sustainability of irrigation water use for agroindustrial avocado production in Ziracuaretiro, Michoacán (2012-2021). Our analysis was based on aggregating weather and soil data at the municipal level and official government databases of avocado cultivated surface, fruit production, and water rights concessions. The analysis considers the homogeneity of information throughout the study area. We estimated that rainfed plantations require 839.03 m³/ton and irrigated plantations require 2355.80 m³/ton, with an average of 1597.47 m³/ton. In addition, we determined that avocado cultivation can demand up to 124.3% of agricultural water concessions in this municipality. In addition to the WF estimates, the analysis indicates that such studies are fundamental for decision-makers to develop and implement water use-efficiency strategies and shows the need for further research related to water consumption of avocado as a crop at more detailed scales to reduce uncertainty.

Channel bends are one of the most important characteristic features of natural streams. These bends often create the conditions for a hyporheic zone, which has been recognized as a critical component of stream ecosystems. The streambed vertical hydraulic conductivity (K_v), vertical hydraulic gradient (VHG) and Darcian flux (DF) in the hyporheic zone were estimated at 61 locations along a channel bend of the Beiluo River during July 2015 and January 2016. All the streambed attributes showed great spatial variability along the channel bend. Both upward fluxes and downward fluxes occurred during the two test periods, most of studied stream sections were controlled by downwelling, indicating stream water discharge into the subsurface. The average downward flux was higher at the downstream side than at the upstream side of the channel bend, especially in July 2015. The distribution of streambed sediment grain size has a significant influence on the variability of K_v; high percentages of silt and clay sediments generally lead to low K_v values. Higher K_v at the depositional left bank at the upstream site shifted toward the erosional right bank at the downstream site, with K_v values positively correlated with the water depth. This study suggested that the variabilities of K_v and VHG were influenced by the stream geomorphology and that the distribution of K_v was inversely related, to a certain extent, to the distribution of VHG across the channel bend. K_v and VHG were found to have opposite effects on the DF, and the close relationship between K_v and DF indicated that the water fluxes were mainly controlled by K_v.

Calcareous sand deposits are widely distributed along the shoreline in ropical and subtropical regions. Microbially induced calcite precipitation treatment (MICP) is a relatively new method to improve the stiffness and strength of the soil. Little is known about the small-strain shear modulus and damping ratio of MICP-treated calcareous sand, which are two crucial parameters for the prediction of the dynamic behavior of soil. A series of resonant column tests are performed to investigate the dynamic performance of MICP-treated calcareous sand, with special attention paid to the influence of treatment duration and confining stress on the stiffness and damping characteristics. The relationship between the initial dynamic shear modulus and unconfined compressive strength is analyzed. Additionally, the empirical equations of the reference shear strain between treatment duration and confining stress are given. The G/G0 of MICP-cemented calcareous sand presents a higher strain sensitivity than that of untreated sand, and its attenuation pattern can be described by Hardin-Drnevich model. The σc has an apparent effect on the degradation characteristics of the dynamic shear modulus of MICP-treated calcareous sand with a low cementation level, however, its effect decreases with the increasing treatment duration. The relationship between the reference shear strain and the treatment duration and confining stress can be described by a power and a linear formula, respectively.

Transport of carbon, major and trace element by rivers in permafrost-affected regions is one of the key factor of circumpolar aquatic ecosystem response to climate warming and permafrost thaw. While seasonal and annual export fluxes (yields) of carbon (C) and inorganic solutes are fairly well known for all large Arctic rivers, spatial variations in elementary concentration along the river length and among its tributaries remain poorly understood. Moreover, the landscape factors controlling riverine element concentration in permafrost-affected regions are still poorly constrained. This is especially true for the largest river of Eastern Siberia, the Lena River, which drains through continuous permafrost zones with highly variable lithology and vegetation. Here we present the results of C, major and trace element measurements over a 2600-km transect of the Lena River main stem (upper and middle reaches) including its 30 tributaries, conducted at the peak of the spring flood. There were two main group of solutes in the main stem depending on their spatial pattern: i) elements that decreased their concentrations downstream, from SW to NE (Cl, SO4, DIC, Li, B, Na, Mg, K, Ca, As, Sr, Mo, Sb, Ba and U), which probably reflected a decrease in the proportion of carbonate rocks in the watershed and the degree of groundwater feeding, and ii) elements that increased their concentrations downstream (Al, Ti, Cr, Fe, Ga, Rb, Y, Zr, Nb, Cs, REEs, Hf and Th), which was tentatively linked to an increase in organic C stock in soils, larch forest coverage and enhanced mobilization of lithogenic elements from silicate soil minerals. Based on landscape parameters of Lena tributaries, we tested the impact of major environmental factors on major and trace element spatial pattern. Among all the variables, the proportion of sporadic permafrost on the watershed strongly controlled concentrations of soluble highly mobile elements (Cl, B, DIC, Li, Na, K, Mg, Ca, Sr, Mo, As and U). Another important factor of element concentration control in the Lena River tributaries was the coverage of watershed by light (B, Cl, Na, K, U) and deciduous (Fe, Ni, Zn, Ge, Rb, Zr, La, Th) needle-leaf forest (pine and larch). The latter, however, could also reflect the DOC-enhanced transport of low-soluble trace elements in the NW part of the basin. This part of the basin is dominated by silicate rocks and continuous permafrost, as compared to carbonate rock-dominated and groundwater-affected SW part of the Lena River basin. Overall, the impact of rock lithology and permafrost on major and trace solutes of the Lena River basin during the peak of spring flood was mostly detected at the scale of the main stem. Such an impact for tributaries was much less pronounced, because of the dominance of surface flow and lower hydrological connectivity with deep groundwater in the latter. Future changes in the river water chemistry linked to climate warming and permafrost thaw at the scale of the whole river basin are likely to be linked to changes in spatial pattern of dominant vegetation, rather than to the permafrost regime. We argue that comparable studies of large, permafrost-impacted rivers during most contrasting seasons, including winter baseflow, should allow efficient prediction of future changes in riverine ‘inorganic’ hydrochemistry induced by permafrost thaw.

Soil organic matter (SOM) is essential for nutrient cycling and soil carbon (C) accumu-lation, both of which are heavily influenced by the quality and quantity of plant litter. Since SOM dynamics in relation to plant diversity are poorly understood we investigated the effects of willow variety and mixture, and site on the soil C stocks, SOM chemical composition and ther-mal stability. Using pyrolysis-field ionization mass spectrometry we analysed the top 10 cm of soil from two 7-year-old experimental sites in Germany and Sweden, with monocultures and mixtures of two willow varieties (Salix spp.) belonging to different species. Overall, site had the strongest effect on SOM quality. Results showed significant variability across sites for willow identity and mixture effects on C accumulation and SOM chemistry. In the German site (Ros-tock), yearly soil C accumulation was higher (p < 0.05) for variety ‘Loden’ (1.0 Mg C ha-1 year-1) compared to ‘Tora’ (0.5 Mg C ha-1 year-1), whilst in the Swedish site (Uppsala), both varieties ex-hibited similar soil C accumulation rates of around 0.6 Mg C ha-1 year-1. Willow variety identity significantly affected SOM quality at both sites, while mixing had minor effects. Our findings emphasize the significance of site-specific context and variety or species identity in shaping soil C accumulation in willow plantations.

Monolayered MoS₂ is energetically most stable when it has a 1H phase, but 1H to 1T phase transition (1H→1T) is easily realized by various ways. Even though magnetic moment is not observed during 1H1T, 0.049 µB/MoS₂ is obtained in local 1T phase; 75% 2H and 25% 1T phases are mixed in (2×2) supercell. Furthermore, non-negligible magnetocrystalline anisotropy (MCA) energy is occured. Most magnetic moment as well as MCA are originated by 1T phased Mo atom5 in the supercell, while electronic structures of other atoms are similar to non-magnetic. Due to this, magnetic/non-magnetic boundary is created in the monolayered MoS2. Our result suggests that MoS₂ can be applied for spintronics such as a spin transistor.

Oncomelania Hupensis is the exclusive intermediary host of Schistosoma japonicum in China. The alteration of its habitat and population distribution directly affects the safety of millions of individuals residing in the Yangtze River Economic Belt (YREB), and the ecological stability. Therefore, it is crucial to analyse the influence of climate change on the distribution of O. Hupensis in order to achieve accurate control over its population. This study utilised the MaxENT model to forecast possible snail habitats by utilising snail distribution data obtained from historical literature. The subsequent outcomes were achieved: The primary ecological factors influencing the distribution of O. Hupensis are elevation, minimum temperature of coldest month, and precipitation of wettest month; Furthermore, future climate scenarios indicate a decrease in the distribution area and a northward shift of the distribution centre for O. hupensis; Specifically, those in the upstream will move northeast, while those in the midstream and downstream will move northwest; These changes in suitable habitat area, the average migration distance of distribution centers across different climate scenarios, time periods, and sub-basins within the YREB, resulting in uncertainty. This study offers theoretical justification for the prevention and control of O. hupensis along the YREB.

The Gol'denveizer problem of a torus can be described as follows: a toroidal shell is loaded under axial forces and the outer and inner equators are loaded with opposite balanced forces. Gol'denveizer pointed out that the membrane theory of shells is unable to predict deformation in this problem, as it yields diverging stress near the crowns. Although the problem has been studied by Audoly and Pomeau (2002) with the membrane theory of shells, the problem is still far from resolved within the framework of bending theory of shells. In this paper, the bending theory of shells is applied to formulate the Gol'denveizer problem of a torus. To overcome the computational difficulties of the governing complex-form ordinary differential equation (ODE), the complex-form ODE is converted into a real-form ODE system. Several numerical studies are carried out and verified by finite-element analysis. Investigations reveal that the deformation and stress of an elastic torus are sensitive to the radius ratio, and the Gol'denveizer problem of a torus can only be fully understood based on the bending theory of shells.

Background: Antibiotic resistance is an urgent issue everywhere in the globe. It is necessary to look into new sources of antibiotics to address this issue. Aim of the study: studying the purification of Corallopyronin B from various soil conditions in Egypt, as well as the antibacterial effectiveness of Corallopyronin B in preclinical animal testing and randomized human clinical trials phases 1/2. Type of the study: Screening experimental study. Methodology: Several soil conditions in Egypt were examined to create bacterial isolates that generated the antibiotic chemical Corallopyronin B. Using reversed-phase HPLC, Myxopyronin B was purified. The test antibiotic's minimum inhibitory concentration( MIC) and in vitro antibacterial activity were ascertained using the paper disc diffusion assay and the broth microdilution technique. Furthermore, in stages 1/2 of randomized clinical trials including human and animal models, pharmacokinetics, adverse drug reactions, and the in vivo antibacterial spectrum were discovered. Results: The soil bacterial isolate Corallococcus coralloides DSM 2259, grown on a Casein yeast peptone( CYP) plate, produced Corallopyronin B from its culture supernatant. At MICs more than 100 mcg/ml, the test antibiotic inhibited the growth of many Gram -ve bacteria, including Escherichia coli, while preventing the growth of numerous Gram +ve bacteria, with MICs ranging from 1 to 10 mcg/ml. Eukaryotic cells, on the other hand, including those in humans and fungi, were unharmed. The test antibiotic was shown to have a bactericidal effect by inhibiting bacterial DNA-dependent RNA polymerase( RNLP). In phases 1/2 of randomized human clinical trials, when 600 mg of the dose per 70 kg of body weight was administered SC, the Cmax was 8.6 mcg/ml at Tmax 1 hour; T1/2 reached 136 min following first-order kinetics of elimination. It stopped acting around 6-7 hours after SC was administered. In the preclinical and randomized human clinical trial phases 1/2, less than 6 percent of experimental candidates had uncommon toxicity, showing reduced bile flow. Protein binding with plasma albumin was detected which reached about 83%. Conclusion: The current work was noteworthy since it involved the production of the bactericidal antibiotic Corallopyronin B from Corallococcus coralloides DSM 2259 which was isolated from several soil environments in Egypt.

Foam concrete is a construction material with controllable low strength and untraditional physical properties. Its highly crushable nature leaves it a niche as an engineered energy-absorbing material in many value-added applications; however, fundamental understanding of the material properties is crucial. As foam concrete is highly cellularized and ductile, conventional concrete testing methods such as compression test are insufficient to characterize the key material attributes of foam concrete, especially when the foam density is low. The resonant frequency test (ASTM C215) is specified for evaluating dynamic Young’s modulus of normal concrete. Inspired by the non-destructive feature of this test, we investigate the possibility of using the resonant frequency test to continuously monitor the modulus build-up of foam concrete with age. For the representativeness of the samples, three variables are considered in material design—bulk density ranging from 0.4 to 1.2 g/cm3, water to cementitious materials ratio of 0.42 and 0.47, and fly ash replacement of 10 and 30% by weight of cement. After examining the different vibration modes, the fundamental transverse frequency is determined most suitable for interpreting the foam modulus. The experimental results demonstrate good accuracy of using this approach for the measurement of different samples. It is also confirmed that, for a given foam concrete, the foam modulus can be predicted by knowing the foam density and solid modulus of its base cement paste, which provides an important insight for the further studies and real applications of foam concrete.

Soil organic matter (SOM) is important for the global carbon cycle, and hyperspectral remote sensing has proven a promising method for fast SOM content estimation. However, soil physical properties significantly affect the sensitivity of satellite hyperspectral imaging to SOM, leading to poor generalization ability of the estimation model. This study aims to improve the spatiotemporal transferability of the SOM prediction model by alleviating the coupling effect of soil physical properties on the spectra. Based on satellite hyperspectral images and soil physical variables, including soil moisture (SM), soil surface roughness (root mean squared height, RMSH), and soil bulk weight (SBW), a soil spectral correction strategy was established based on the information unmixing method. Two important grain-producing areas in Northeast China were selected as study areas to verify the performance and transferability of the spectral correction model and SOM content prediction model. The results showed that soil spectral corrections based on fourth-order polynomials and the XG-Boost algorithm had excellent accuracy and generalization ability, with residual predictive deviations (RPD) exceeding 1.4 in almost all bands. In addition, when the soil spectral correction strategy was adopted, the accuracy of the SOM prediction model and the generalization ability after model migration were significantly improved. The SOM prediction accuracy based on the XG-Boost corrected spectrum was the highest, with a coefficient of determination (R2) of 0.76, root mean square error (RMSE) of 5.74 g/kg, and RPD of 1.68. The prediction accuracy, R2, RMSE, and RPD of the model after migration were 0.72, 6.71 g/kg, and 1.53, respectively. Compared with the direct migration prediction of the model, adopting the soil spectral correction strategy based on fourth-order polynomials and XG-Boost reduced the RMSE of the SOM prediction results by 57.90% and 60.27%, respectively. The performance comparison highlighted the advantages of considering soil physical properties in regional-scale SOM prediction.

Thromboembolic conditions, such as stroke and myocardial infarction [MI], are the primary causes of mortality globally. High efficiency was demonstrated by fibrinolytic enzymes isolated from microbial sources in dissolving various blood clots. The study aimed to investigate and produce bacterial fibrinolytic enzymes from various Egyptian soil conditions using recombinant DNA technology. Fifty soil samples were examined to determine the production of fibrinolytic enzymes. The plasmin plate technique assessed the thrombolytic activities of the strong fibrinolytic enzyme-producing bacterial isolates. In addition to determining the molecular mass using a mass spectrometer and the western blot method, the activity and thermostability of the enzymes were characterized. An affinity chromatography approach was used to purify the fibrinolytic enzymes. However, bacterial recombinant DNA technology produced the pure bacterial fibrinolytic enzyme. Several dosage formulations for the formulation of fibrinolytic enzymes were tested. By using affinity chromatography and the SDS-PAGE test, the isolated bacterial fibrinolytic enzyme in this investigation was almost 83% pure. Bacillus cereus ATCC 4342 was identified as the predominant bacterial isolate secreting fibrinolytic enzymes. It was discovered that the fibrinolytic enzyme activity of fifty soil samples ranged from 0.167 U/ml to 1.853 U/ml. The extracellular enzyme extracted from Bacillus cereus culture supernatant demonstrated a relatively stable fibrinolytic activity over 18 hours at a pH range of 7.4–10, as well as stability with maximum productivity at 43℃ for over 60 minutes. In this investigation, the enzyme was referred to as Fibrin-proteinase[ FP]. The fibrin clots were directly thrombolyzed by the FP. The calculated values for the specific activity and molecular mass of the FP were approximately 40.71 units/mg of protein and approximately 30 KDa, respectively. It was observed that the presence of Fe+3 marginally boosted protease activity, but the presence of EDTA decreased it. On the other hand, adding monovalent cations like K+1 and Na+1 significantly increased the fibrinolytic activity of FP. The enzyme exhibited activity throughout the temperature range of 20 to 65℃, peaking at 55℃. The ideal range for the generation of protease was 35–43℃ and 8.0–10. The thermostable fibrinolytic enzyme FP, which was isolated from Bacillus cereus ATCC 4342 in various soil environments in Egypt during the current study, was a promising fibrinolytic enzyme because it demonstrated a more extensive and effective fibrinolytic activity and fewer side effects than the fibrinolytic enzymes that are currently available worldwide. It is advised that further research be done on optimizing the right formulation of bacterial fibrinolytic enzymes in the future to help dissolve different types of blood clots and, as a result, lower the high death rate that exists worldwide.

This study aims to improve the shaft with hexagon joints to be a type not requiring welding or bolts in the static load test . In order to evaluate the bearing capacity of helical piles, two sites were selected to conduct pile installation for the field test and the pile load test. For the pile load test, the static pile load test and the dynamic pile load test were carried out, and torque was measured during pile installation for the field test to compare and analyze expected bearing capacity and thus assess the feasibility of the method for estimating the bearing capacity. The field pile load test revealed the bearing capacity of the gravity grout pile was the same or greater than 600kN in the static pile load test in accordance with AC 358 Code. The non-grout pile showed the bearing capacity the same or smaller than 600kN, suggesting gravity grouting is required. Moreover, the field pile load test was used to establish the bearing capacity equation considering the torque in pile installation, and a small number of samples were used to establish the equation which can be used as a basic data.

The long-term use of fertilizers and pesticides in conventional cultivation has resulted in a decrease in soil productivity and vegetable yields in greenhouses. However, only a limited number of studies have explored the impacts of organic cultivation on greenhouse soil. Specifically, there is a scarcity of research examining the alterations in soil aggregate mediated organic carbon and microbial communities, which are known to enhance soil productivity. This study investigated the properties of soil aggregates, including the levels of organic carbon fractions, microbial community, and enzyme activity with the three aggregate classes microaggregates (&lt;0.25 mm), small macroaggregates (2-0.25 mm) and large macroaggregates (&gt;2 mm). These investigations were conducted under three different cultivation methods in a greenhouse: conventional cultivation (CC), integrated cultivation (IC), and organic cultivation (OC) in greenhouse. The results showed that (1) OC and IC promoted the formation of small macro-aggregates and enhanced aggregate stability compared to CC, (2) SOC in the three size fractions of OC increased by 98.99%-92.06% compared to CC; EOC increased by 98.47%-117.59%; POC increased by 138.59%-208.70%; MBC increased by 104.71%-230.61%; DOC increased by 21.93%-40.90%, respectively; (3) Organic cultivation significantly increased enzyme activity in all three particle size aggregates and increased the relative abundance of bacteria in micro-aggregates as well as the relative abundance of fungi in small macro-aggregates. Structural equation model (SEM) analysis revealed that organic farming practices fostered the development of smaller macro-aggregates, elevated microbial and enzyme activities within soil aggregates, and facilitated the conversion of soil nutrients and carbon sequestration. consequently, this led to an increase in soil organic carbon content and improved vegetable yield in greenhouse environments. In conclusion, the soil carbon content and vegetable yield are enhanced through long-term organic cultivation in greenhouses, primarily by increasing the proportion of small macro-aggregates.

We study wave patterns of gravity-capillary waves from moving localized sources within the classic setup of the problem of ship wakes. The focus is made on the co-existence of two wave systems with opposite signatures of group velocity relative to the localized source. It leads to the problem of choice of signs for phase functions of the gravity (“slow”) and capillary (“fast”) branches of the dispersion relation: the question generally ignored when constructing phase patterns of the solutions. We detail characteristic angles of the wake patterns: (i) angle of demarcation of gravity and capillary waves – “the phase Mach” cone, (ii) angle of the minimal group velocity of gravity-capillary waves – “the group Mach” cone, (iii, iv) angles of cusps of isophases that appear after a threshold current speed. The outer cusp cone is naturally associated with the classic cone of Kelvin for pure gravity waves. The inner one results from the effect of capillarity and tends to the “group Mach” pattern at high speeds of current. Amplitudes of the wave patterns are estimated within the recently proposed approach of reference functions for the problem of propagation of packets of linear dispersive waves. The effect of shape is discussed for elliptic reference sources.

Industrial dynamical systems often exhibit multi-scale response due to material heterogeneities, operation conditions and complex environmental loadings. In such problems, it is the case that the smallest length-scale of the systems dynamics controls the numerical resolution required to effectively resolve the embedded physics. In practice however, high numerical resolutions is only required in a confined region of the system where fast dynamics or localized material variability are exhibited, whereas a coarser discretization can be sufficient in the rest majority of the system. To this end, a unified computational scheme with uniform spatio-temporal resolutions for uncertainty quantification can be very computationally demanding. Partitioning the complex dynamical system into smaller easier-to-solve problems based of the localized dynamics and material variability can reduce the overall computational cost. However, identifying the region of interest for high-resolution and intensive uncertainty quantification can be a problem dependent. The region of interest can be specified based on the localization features of the solution, user interest, and correlation length of the random material properties. For problems where a region of interest is not evident, Bayesian inference can provide a feasible solution. In this work, we employ a Bayesian framework to update our prior knowledge on the localized region of interest using measurements and system response. To address the computational cost of the Bayesian inference, we construct a Gaussian process surrogate for the forward model. Once, the localized region of interest is identified, we use polynomial chaos expansion to propagate the localization uncertainty. We demonstrate our framework through numerical experiments on a three-dimensional elastodynamic problem

The impact of sex in the development of long-term toxicities affecting the quality of life of cancer survivors has not been investigated experimentally. To address this issue, a series of neurologic and cardiologic endpoints were used to investigate sex-based differences triggered by paclitaxel treatment and radiotherapy exposure. Male and female WT mice were treated with Paclitaxel (150 and 300 mg/kg) administered weekly over 6 weeks or exposed to 19 Gy cardiac irradiation. Cohorts were analyzed for behavioral and neurobiologic endpoints to assess systemic toxicity of paclitaxel or cardiovascular endpoints to assess radiotherapy toxicity. Interestingly, female WT mice exhibited enhanced tolerance compared to male WT mice regardless of the treatment regimen. To provide insight into the possible sex-specific protective mechanisms, rhoB deficient animals and elderly mice (22 months) were used with a focus on the possible contribution of sex hormones including estrogen. RhoB deficiency and advanced age had no impact on neurocognitive impairment induced by Paclitaxel but reversed the cardioprotection was observed in females after radiotherapy. Conversely, rhoB deficiency protected males from radiation toxicity. In sum, rhoB was identified as a molecular determinant driving estrogen dependent cardioprotection in female mice, whereas neuroprotection was not sex-hormone dependent. To our knowledge, this study revealed for the first time sex- and organ-specific responses to paclitaxel and radiotherapy.

Background: Antibiotic resistance is an urgent issue everywhere in the globe. It is necessary to look into new sources of antibiotics to address this issue. Aim of the study: studying the purification of Corallopyronin B from various soil conditions in Egypt, as well as the antibacterial effectiveness of Corallopyronin B in preclinical animal testing and randomized human clinical trials phases 1/2. Type of the study: Screening experimental study. Methodology: Several soil conditions in Egypt were examined to create bacterial isolates that generated the antibiotic chemical Corallopyronin B. Using reversed-phase HPLC, Myxopyronin B was purified. The test antibiotic's minimum inhibitory concentration( MIC) and in vitro antibacterial activity were ascertained using the paper disc diffusion assay and the broth microdilution technique. Furthermore, in stages 1/2 of randomized clinical trials including human and animal models, pharmacokinetics, adverse drug reactions, and the in vivo antibacterial spectrum were discovered. Results: The soil bacterial isolate Corallococcus coralloides DSM 2259, which was grown on a Casein yeast peptone( CYP) plate, produced Corallopyronin B from its culture supernatant. At MICs more than 100 mcg/ml, the test antibiotic inhibited the growth of many Gram -ve bacteria, including Escherichia coli, while also preventing the growth of numerous Gram +ve bacteria, with MICs ranging from 1 to 10 mcg/ml. Eukaryotic cells, on the other hand, including those in humans and fungi, were unharmed. The test antibiotic was shown to have a bactericidal effect by inhibiting bacterial DNA-dependent RNA polymerase( RNLP). In phases 1/2 of randomized human clinical trials, when 600 mg of the dose per 70 kg of body weight was administered SC, the Cmax was 8.6 mcg/ml at Tmax 1 hour; T1/2 reached 136 min following first-order kinetics of elimination. It stopped acting around 6-7 hours after SC was administered. In the preclinical and randomized human clinical trial phases 1/2, less than 6 percent of experimental candidates had uncommon toxicity, which showed up as reduced bile flow. Protein binding with plasma albumin was detected which reached about 83%. Conclusion: The current work was noteworthy since it involved the production of the bactericidal antibiotic Corallopyronin B from Corallococcus coralloides DSM 2259 which was isolated from several soil environments in Egypt.

Background: Antibiotic resistance is an overwhelming serious difficulty globally. This necessitates the exploration of novel sources of antibiotics to overcome this challenge. Aim of the study: Bacterial Myxopyronin A production from various soil environments Egypt; as well as testing its antimicrobial activity in preclinical animal testing and randomized human clinical trials phases 1/2. Type of the study: Screening experimental study. Methodology: Different soil environments in Egypt were screened for the growth of bacterial isolates producing Myxopyronin A as an antimicrobial agent. Purification of Myxopyronin A was performed via reversed-phase HPLC. Paper disc diffusion assay, as well as the Broth dilution technique, were exploited to assess the invitro antimicrobial and minimum inhibitory concentration( MIC) of the test antibiotic. Furthermore, in vivo antimicrobial spectrum, adverse drug reactions, and pharmacokinetics were detected during animal model testing stages and human randomized clinical trials phases 1/2. Results: From the culture supernatant of the Myxobacterium Myxococcus fulvus 124B02 which was the predominant soil bacterial isolate grown on the Casein yeast peptone plate, Myxopyronin A was produced. The test antibiotic blocked the growth of many Gram +ve bacteria with MICs less than 100 mcg/ ml. In contrast, it inhibited the growth of a few Gram -ve bacteria such as Escherichia coli at MICs greater than 100 mcg/ ml. On the other hand, Eukaryotic cells such as fungal and human cells were not affected. Prokaryotic DNA-dependant-RNA polymerase( RNLP) was noticed to be inhibited via the test antibiotic suggesting its bactericidal action. The maximum concentration was 7-8 mcg/ ml at a maximum time of 2 hours when 600 mg dose was orally administered in randomized human clinical trials phases 1/2, and T1/2 reached 2.5 hours following first-order kinetics of elimination. The duration of its action was nearly 12 hours after oral administration. Rare toxicity was detected during preclinical and randomized human clinical trials phases 1/2 in the form of mild diarrhea and cholestatic jaundice in less than 5 % of experimental candidates. Conclusion: The present study was promising due to the bactericidal antibiotic Myxopyronin A production from Myxococcus fulvus 124B02 isolated from different soil environments in Egypt.

This study outlines the development of an innovative method utilizing UHPLC-PDA for the simultaneous identification of polyphenols and bitter acids (alpha-acids, beta-acids, and iso-alpha-acids) in beer samples. The resulting chemical profiles were leveraged to distinguish the characteristics of four bergamot-flavored beers, each representing distinct styles (IPA, Lager, Blanche, and ALE), produced on a pilot-scale plant. In a streamlined 29-minute analysis, twenty-nine polyphenols and fourteen bitter acids were successfully identified under optimized separation conditions. Rigorous validation, encompassing parameters such as Limit of Detection (LOD), Limit of Quantification (LOQ), R-squared (R2), repeatability, and reproducibility, was conducted for polyphenol quantification using constructed calibration curves with seven levels. Exploring polyphenolic components as potential discriminators among different beer styles, a total of thirty-two polyphenolic compounds were identified and quantified, including characteristic bergamot peel polyphenols like neoeriocitrin, naringin, and neohesperidin. The determination of bitter units and total phenols further aided in style differentiation. Multivariate analysis provided additional insights into variations among specific beer styles, revealing discrepancies in the presence or relative concentrations of specific compounds linked to brewing ingredients and processes. This research enhances to trace the fingerprinting of the chemistry governing beer quality through a straightforward and cost-effective analytical approach, readily applicable in common laboratories.

The soil organic matter (SOM) content and stability in natural gypsum soils and soils from mining/industrial areas were compared, in terms of their physical, chemical and micromorphological properties, to determine whether the old brownfield soils were acting as carbon (C) sinks, counteracting increasing carbon dioxide concentrations in the atmosphere. The mining/industrial soils were 50–400 years old, so had been left sufficiently long for full self-restoration. Despite having very different origins, both natural and brownfield soils stored similar amounts of SOM, and had similar pH values, calcium carbonate contents and textures. They were also fully covered with similar grass plant communities. The mining/industrial soils exhibited similar microstructures to the gypsum soils and were often quite porous. The most striking difference between them and the natural gypsum soils was that the mining/industrial soils were strongly polluted with zinc, lead and cadmium. The 50-year-old brownfield soils differed from the others in terms of having a lower state of SOM transformation, with a much higher C/N ratio, lower aggregate water resistance index, lower dehydrogenase activity and greater areas of undecomposed or slightly decomposed plant residues. These parameters in the older (150–400 years) brownfield soils were similar to those of the natural soils.

Heavy metals constitute pollutants particularly common in air, water, and soil. They are present in both urban and rural environments, on land and in marine ecosystems, causing serious environmental problems since they do not degrade easily, remain almost unchanged for long periods, and bioaccumulate. Detection, though especially quantification, is a systematic process as monitoring of their levels needs to be carried out at regular intervals since there is often seasonal variation. The need for rapid and low-cost determination of metals is therefore considerable. In the present study atomic absorption spectroscopy (AAS), using a flame or graphite furnace, and square wave anodic stripping voltammetry (SWASV), using a bismuth thin film electrode, a sensitive voltammetric method is being compared and analytically validated. Atomic absorption spectroscopy (AAS) represents a well-established analytical technique while anodic stripping voltammetry is being criticized for its applicability in complicated sample matrices such as soil samples. This sample-handling challenge is being investigated in the present study. The results show that both methods AAS and ASV were satisfactorily correlated and showed that the concentration of metals is lower than the limit values, but with increasing trend. Therefore, continuous monitoring of metal levels in the urban complex of the city is necessary and a matter of great importance. Regarding Cd, the detection limits of Cd are lower compared to those of AAS when using the graphite furnace, while an overestimation was noted when using flame-AAS in comparison with those found with SWASV. The SWASV method has the advantage of being cheaper and faster, enabling the simultaneous determination of heavy elements across the range of concentrations that these elements can occur in Mediterranean soils. Additionally, we applied a dsDNA-modified electrode which can be used in the speciation analysis of Cu(I) and Cu(II). The changes in the characteristic peaks of guanine and adenine can be applied in the redox speciation analysis of copper in soil which represents an issue of great importance.

This study uses a mass-spring-damping system to simulate the repeated strain of liquefaction cyclic triaxial tests. The two results are compared in this paper to understand the feasibility of the mass-spring-damping system developed in this paper and the feasibility of future research on this related topic and development potential. The main factors affecting this mode's repeated strain are the spring coefficient k and the external force Q0. The spring coefficient has an inverse relationship but does not increase in multiples. The external force has a direct proportional relationship but does not increase the result- a non-multiple increase. When the pore water pressure of the liquefied cyclic triaxial test specimen rises, it will cause the specimen to liquefy, decreasing effective stress, shear modulus G, and damping ratio D, causing an increase in strain. The shear modulus and damping ratio are related to the spring coefficients k and c. Both are variables that change with time. This article takes an original thin-tube specimen at point A in the Yunlin area in Taiwan as a testing example. Through Mathematica software, it can be obtained that the mass m=1kg, the spring coefficient k=244e-0.1t kgf/cm, and the damping coefficient c=0.739e-0.257t kgf-s/cm and external force Q0=10.1sin2πt kg; Finally, this study selected the original thin-tube specimens from four locations in the Yunlin area, and simulated the repeated strain amount of the cyclic triaxial test specimens through a spring-damping system. The results show that the spring-damping system is feasible for simulated cyclic triaxial tests because the model is simple and the parameters are easy to understand and obtain, which also shows the extensibility of this model. Preliminary results of the research show that this model can further simulate the repeated strain obtained by cyclic triaxial tests without considering the increased trend in pore water pressure and the decrease in effective stress during cyclic loading.

Knowing the mechanical properties of fibrous composite materials used in aeronautical industry from the design phase is a primary objective for designers. There are many methods for determining them, but they are laborious and require a long calculation time. And some of the methods are very approximate, giving only upper and lower bounds for these values. Experimental measurements also consume time and others resources. A method for sufficiently accurate and quickly obtained estimation of the engineering constants of the homogenized material is presented in the work. FEM is used to determine the natural frequencies of a standard bar, for which there are sufficiently precise classical methods for expressing these constants according to the properties of the homogenized material. In this way, these sought constants can be determined. In the work, Young's modulus will be determined for such a material, using the relationships that provide the proper pulsations for the longitudinal vibrations. Within the adopted model, transverse and torsional vibrations will be eliminated by blocking the nodes on the surface of the bars. In this way, more longitudinal self-pulsations can be obtained, so the precision in calculating the Young's modulus will increase.

When developing bone implants Young's modulus is one of the primary characteristics of the material that should be considered. The study focuses on the possibility of regulating the modulus of the alloy Ti-50.8 at % Ni by varying its initial structure as well as aging-induced microstructure in a wide range. Microstructure observations were performed using TEM and SEM observations. The calorimetric studies of martensitic transformations were carried out using "Mettler Toledo 822e". Tensile tests were performed in a test temperature range of ‒196≤T≤+100°C using an «IN-STRON 5966». The grain/subgrain size of B2-austenite strongly affects the modulus magnitude. This effect is ambiguous for a material with a grain size of 0.13–3 µm and depends on the test temperature. The effectiveness of aging on the modulus reduction depends on the initial structure: it is most pronounced in an alloy with a relatively coarse grain size of 9 µm and brings a decrease by 3.8 times at a temperature of 37°C. Bone-like elastic modulus (10–30 GPa) at a human body temperature of 37°C is realized in an aged fine-grained NiTi alloy. An ultrafine-grained sub-structure exhibits he same values of Young's modulus in the temperature range from -100°С to 25°С.

Background: Across the world, antibiotic resistance is a critical challenge. To address such a problem, it has to be done to investigate new antibiotic sources. Aim of the study: Study of the antibacterial activity of Corallopyronin A in preclinical animal testing and randomized human clinical trials stages 1/2, as well as investigating the purification of Corallopyronin A from different soil conditions in Egypt. Type of the study: Screening experimental study. Methodology: Egypt's various soil conditions were tested to develop bacterial isolates that produced the antibiotic compound Corallopyronin A. Reversed phase HPLC was used to purify Myxopyronin A. The broth microdilution method and the paper disc diffusion assay determined the test antibiotic's minimum inhibitory concentration( MIC) and in vitro antibacterial activity. Moreover, in vivo antibacterial spectrum, adverse medication responses, and pharmacokinetics were found in phases 1/2 of randomized clinical studies involving humans and animal models. Results: Corallopyronin A was generated from the culture supernatant of the soil bacterial isolate Corallococcus coralloides M2, cultivated on a Casein yeast peptone( CYP) plate. The test antibiotic prevented the growth of several Gram-ve bacteria, including Escherichia coli, at MICs higher than 100 mcg/ ml; while blocking the development of many Gram +ve bacteria, with MICs ranging from 3 to 15 mcg/ ml. However, eukaryotic cells—such as those found in fungi and humans—were unaffected. A bactericidal consequence of the test antibiotic was detected in the inhibition of prokaryotic DNA-dependent RNA polymerase( RNLP). Conclusion: The synthesis of the bactericidal antibiotic Corallopyronin A from Corallococcus coralloides M2 isolated from different soil settings in Egypt intrigued the current investigation.

The nonlinear deformation and stress analysis of a circular torus is a difficult undertaking due to its complicated topology and the variation of the Gauss curvature. A nonlinear deformation (only one term in strain is omitted) of Mindlin torus was formulated in terms of the generalized displacement, and a general Maple code was written for numerical simulations. Numerical investigations show that the results obtained by nonlinear Mindlin, linear Mindlin, nonlinear Kirchhoff-Love, and linear Kirchhoff-Love models are close to each other. The study further reveals that the linear Kirchhoff-Love modeling of the circular torus gives good accuracy and provides assurance that the nonlinear deformation and stress analysis (not dynamics) of a Mindlin torus can be replaced by a simpler formulation, such as a linear Kirchhoff-Love theory of the torus, which has not been reported in the literature.

Successful fertilization treatments targeted to improve stand productivity while reducing operational complexities and cost depend on a clear understanding of soil nutrient availability under varying environmental conditions. Soil nutrient data collected from 154 forest sites throughout the Inland Northwest, USA were analyzed to examine soil nutrient characteristics on different geologic soil parent materials and to rank soil fertility. Results show that soil parent material explains significant differences in soil nutrient availability. Soils developed from volcanic rocks have the highest CEC and are relatively high in P, K, S, Mg, Cu, Ca, and B, but generally poor in N. Forest soils developed from plutonic rocks exhibit the lowest CEC and are low in N, S, K, Mg, Cu, and Ca, but higher in P. Some soils located on mixed glacial till are low only in K, Cu, Mg, and Ca, but many glacial soils are relatively rich in other nutrients, albeit the second lowest CEC. Soils developed from metasedimentary and sedimentary rocks are among those with lowest soil nutrient availability for P and B. Sulfur was found to have the highest concentrations in metasedimentary influenced soils and the least in sedimentary derived soils. Our results should be useful in designing site-specific fertilizer and nutrient management prescriptions for forest stands growing on soils developed from these major geologies within the Inland Northwest region of the United States.

Silicon (Si) is the major material of semiconductor element. For semiconductor element producing, Si need to refined into high-purity silicon crystals, which has the approximate characteristics of intrinsic semiconductor, then doping 13th group or 15th group trace element. Producing the high-purity silicon crystals with well-lattice structure need a lot of energy and highly cost. Besides, the high-purity silicon is very hard and fragile which limits the scope of application. For this reason, this study added low-grade non-complete lattice silicon in the elastic polymer, and then doped with high concentrations of fine carbon powder. This material can be conductive by physisorption;therefore, it can be used to making semiconductors. Using this material to produce electronic components can significantly reduce the cost of purification and crystallization, saving energy at the same time. Moreover, because this elastic polymer materials containing silicon, which has soft, warm, and durable physical properties. With those properties, the design of the device could be more flex, full scalability and close to the skin.

Machine learning methods have been a standard approach to select features that are associated with an outcome and build a prediction model when the number of candidate features is large. LASSO has been one of the most popular approaches to this end. LASSO approach selects features with large regression estimates, rather than based on statistical significance, associating the outcome, by imposing L1-norm penalty to overcome the high dimensionality of the candidate features. As a result, LASSO may select insignificant features while possibly missing significant ones. Furthermore, from our experience, LASSO has been found to select too many features. By selecting features that are not associated with the outcome, we may have to spend more cost to collect and manage them in the future use of a fitted prediction model. Using the combination of L1- and L2-norm penalties, elastic net (EN) tends to select more features than LASSO. The overly selected features that are not associated with the outcome act like white noise, so that the fitted prediction model loses the prediction accuracy. In this paper, we propose to use the standard regression methods (without any penalizing approach) with stepwise variable selection procedure to overcome these issues. Unlike LASSO and EN, this method selects features based on statistical significance. Through extensive simulations, we show that this maximum likelihood estimation based method selects very small number of features while maintaining a high prediction power, while LASSO and EN make a large number of false selections to result in loss of prediction accuracy. Contrary to LASSO and EN, the regression methods combined with a stepwise variable selection method is a standard statistical method, so that any biostatistician can use it to analyze high dimensional data even without advanced bioinformatics knowledge.

BACKGROUND: Thromboembolic disorders including Myocardial infarction[ MI] and stroke represent the leading causes of death worldwide. Fibrinolytic enzymes extracted from microbial sources showed high efficacy in the dissolution of different blood clots. AIM OF THE STUDY: Screening and the bacterial recombinant DNA manufacture of bacterial fibrinolytic enzymes from different soil environments in Egypt. METHODOLOGY: A total of 50 soil samples were screened for their fibrinolytic enzyme production. The potent fibrinolytic enzyme-producing bacterial isolates were evaluated for their thrombolytic activities using the plasma plate method. The characterization of the enzyme activity and thermostability were carried out; also, the determination of molecular mass using a mass spectrometer and western blot technique was performed. The purification of the fibrinolytic enzymes was done through the affinity chromatography technique. On the other hand, the production of the purified bacterial fibrinolytic enzyme was achieved via bacterial recombinant DNA technology. Formulation of fibrinolytic enzymes in different dosage forms was tried. RESULTS: In the present study, the purified bacterial fibrinolytic enzyme was approximately 83% pure through affinity chromatography and SDS-PAGE assay. The predominating bacterial isolate secreting fibrinolytic enzymes was found to be Bacillus cereus. The fibrinolytic enzyme activities of 50 soil samples were found to be in the range of 0.167-1.853 U/ ml. The fibrinolytic activity of the extracellular enzyme refined from the culture supernatant of Bacillus cereus was relatively stable over the PH range from 7.4-10 for 18 hours and also it showed stability with the highest productivity at a temperature of 43 0C for nearly 60 minutes. The enzyme was called fibrin-proteinase[ FP] in the present study. The FP degraded the fibrin clots via direct thrombolysis. The specific activity and the molecular mass of the FP were estimated to be nearly 40.71 Units/ mg protein and nearly 30 KDa respectively. Protease activity was noticed to be slightly increased in the presence of Fe+3; While it was inhibited in the presence of EDTA. On the other hand, the FP fibrinolytic activity was enhanced greatly after the addition of monovalent cations such as K+1 and Na +1. The enzyme was also active over the temperature range of 20- 65 0C with the highest activity at 55 0C. The optimum temperature and PH of protease production was at 35-43 0C and PH 8.0-10. Conclusion: During the present study, the thermostable fibrinolytic enzyme FP purified from Bacillus cereus in different soil environments in Egypt was a promising fibrinolytic enzyme because it showed a broader efficacious fibrinolytic activity as well as less adverse effects than the current fibrinolytic enzymes globally. It is recommended in the future advanced exploration of the optimization of suitable formulation of bacterial fibrinolytic enzymes to aid in the dissolution of various blood clots and as a consequence overcoming the high rate of mortality globally.

Background: Across the world, antibiotic resistance is a critical challenge. To address such a problem, it has to be done to investigate new antibiotic sources. Aim of the study: Study of the antibacterial activity of Corallopyronin A in preclinical animal testing and randomized human clinical trials stages 1/2, as well as investigating the purification of Corallopyronin A from different soil conditions in Egypt. Type of the study: Screening experimental study. Methodology: Egypt's various soil conditions were tested to develop bacterial isolates that produced the antibiotic compound Corallopyronin A. Reversed phase HPLC was used to purify Myxopyronin A. The broth microdilution method and the paper disc diffusion assay determined the test antibiotic's minimum inhibitory concentration( MIC) and in vitro antibacterial activity. Moreover, in vivo antibacterial spectrum, adverse medication responses, and pharmacokinetics were found in phases 1/2 of randomized clinical studies involving humans and animal models. Results: Corallopyronin A was generated from the culture supernatant of the soil bacterial isolate Corallococcus coralloides M2, cultivated on a Casein yeast peptone( CYP) plate. The test antibiotic prevented the growth of several Gram-ve bacteria, including Escherichia coli, at MICs higher than 100 mcg/ ml; while blocking the development of many Gram +ve bacteria, with MICs ranging from 3 to 15 mcg/ ml. However, eukaryotic cells—such as those found in fungi and humans—were unaffected. A bactericidal consequence of the test antibiotic was detected in the inhibition of prokaryotic DNA-dependent RNA polymerase( RNLP). Conclusion: The synthesis of the bactericidal antibiotic Corallopyronin A from Corallococcus coralloides M2 isolated from different soil settings in Egypt intrigued the current investigation.

This paper investigates the influence of magnetic field for a two dimensional deformations on a two temperature problem at the free surface of a semi-infinite semiconducting medium under the effect of mechanical force during a photothermal theory and the effect of hydrostatic initial stress on the medium. The Harmonic Wave Method (Normal Mode Analysis) has been used to obtain the equations of elastic waves, heat conduction equation, quasi-static electric field, carrier density, two temperature coefficient, ratios, and constitutive relationships for the thermo-magnetic-electric medium. The effects of several parameters as thermoelastic and thermoelectric coupling parameters and two temperature parameter of this force on the displacement component, force stress, carrier density and temperature distribution has been depicted graphically.

Verticillium wilt (VW) is a soil borne fungal diseases caused by Verticillium dahliae Kleb, and lead to serious damage to cotton production annually in the world. In our previous study, a transmembrane protein 214 protein (TMEM214) gene associated with VW resistance was map-based cloned from Gossypium barbadense (G. barbadense). TMEM214 proteins are a kind of transmembrane protein, but their function in plants is rarely studied. To reveal the function of TMEM214s in VW resistance, all six TMEM214s were cloned from G. barbadense in this study. These genes were named as GbTMEM214-1, GbTMEM214-4 and GbTMEM214-7 according to their location on the chromosomes, and the encoded proteins are all located on cell membrane. TMEM214 genes were all induced by Verticillium dahliae inoculation and showed significant differences between resistant and susceptible varieties, but the expression patterns of GbTMEM214s under different hormone treatments were significantly different. Virus-induced gene silencing analysis showed the resistance to VW of GbTMEM214s-silenced lines decreased significantly, which further proves the important role of GbTMEM214s in the resistance to Verticillium dahliae. Our study provides an insight into the involvement of GbTMEM214s in VW resistance, which was helpful to better understand the disease resistance mechanism of plants.

The objectives of the study were to determine the spatial rate of CO₂ flux (Net Ecosystem Exchange) and soil moisture in a wetland ecosystem applying Sentinel-1 IW (Interferometric Wide) data of VH (Vertical Transmit/Horizontal Receive—cross polarization) and VV (Vertical Transmit/Vertical Receive—like polarization) polarization. In-situ measurements of carbon flux, soil moisture, and LAI (Leaf Area Index) were carried out over the Biebrza Wetland in north-eastern Poland. The impact of soil moisture and LAI on backscattering coefficient (σ°) calculated from Sentinel-1 data showed that LAI dominates the influence on σ° when soil moisture is low. The models for soil moisture have been derived for wetland vegetation habitat types applying VH polarization (R² = 0.70 to 0.76). The vegetation habitats: reeds, sedge-moss, sedges, grass-herbs, and grass were classified using combined one Landsat 8 OLI (Operational Land Imager) and three TerraSAR-X (TSX) ScanSAR VV data. The model for the assessment of Net Ecosystem Exchange (NEE) has been developed based on the assumption that soil moisture and biomass represented by LAI have an influence on it. The σ° VH and σ° VV describe soil moisture and LAI, and have been the input to the NEE model. The model, created for classified habitats, is as follows: NEE = f (σ° Sentinel-1 VH, σ° Sentinel-1 VV). Reasonably good predictions of NEE have been achieved for classified habitats (R² = 0.51 to 0.58). The developed model has been used for mapping spatial and temporal distribution of NEE over Biebrza wetland habitat types. Eventually, emissions of CO₂ to the atmosphere (NEE positive) has been noted when soil moisture (SM) and biomass were low. This study demonstrates the importance of the capability of Sentinel-1 microwave data to calculate soil moisture and estimate NEE with all-weather acquisition conditions, offering an important advantage for frequent wetlands monitoring.

BACKGROUND: Thromboembolic disorders including Myocardial infarction[ MI] and stroke represent the leading causes of death worldwide. Fibrinolytic enzymes extracted from microbial sources showed high efficacy in the dissolution of different blood clots. AIM OF THE STUDY: Screening and the bacterial recombinant DNA manufacture of bacterial fibrinolytic enzymes from different soil environments in Egypt. METHODOLOGY: A total of 50 soil samples were screened for their fibrinolytic enzyme production. The potent fibrinolytic enzyme-producing bacterial isolates were evaluated for their thrombolytic activities using the plasma plate method. The characterization of the enzyme activity and thermostability were carried out; also, the determination of molecular mass using a mass spectrometer and western blot technique was performed. The purification of the fibrinolytic enzymes was done through the affinity chromatography technique. On the other hand, the production of the purified bacterial fibrinolytic enzyme was achieved via bacterial recombinant DNA technology. Formulation of fibrinolytic enzymes in different dosage forms was tried. RESULTS: In the present study, the purified bacterial fibrinolytic enzyme was approximately 83% pure through affinity chromatography and SDS-PAGE assay. The predominating bacterial isolate secreting fibrinolytic enzymes was found to be Bacillus cereus. The fibrinolytic enzyme activities of 50 soil samples were found to be in the range of 0.167-1.853 U/ ml. The fibrinolytic activity of the extracellular enzyme refined from the culture supernatant of Bacillus cereus was relatively stable over the PH range from 7.4-10 for 18 hours and also it showed stability with the highest productivity at a temperature of 43 0C for nearly 60 minutes. The enzyme was called fibrin-proteinase[ FP] in the present study. The FP degraded the fibrin clots via direct thrombolysis. The specific activity and the molecular mass of the FP were estimated to be nearly 40.71 Units/ mg protein and nearly 30 KDa respectively. Protease activity was noticed to be slightly increased in the presence of Fe+3; While it was inhibited in the presence of EDTA. On the other hand, the FP fibrinolytic activity was enhanced greatly after the addition of monovalent cations such as K+1 and Na +1. The enzyme was also active over the temperature range of 20- 65 0C with the highest activity at 55 0C. The optimum temperature and PH of protease production was at 35-43 0C and PH 8.0-10. Conclusion: During the present study, the thermostable fibrinolytic enzyme FP purified from Bacillus cereus in different soil environments in Egypt was a promising fibrinolytic enzyme because it showed a broader efficacious fibrinolytic activity as well as less adverse effects than the current fibrinolytic enzymes globally. It is recommended in the future advanced exploration of the optimization of suitable formulation of bacterial fibrinolytic enzymes to aid in the dissolution of various blood clots and as a consequence overcoming the high rate of mortality globally.

In this study the effects of three different main preparatory tillage operations [ploughing at 0.4 m (P40) and 0.20 m (P20) depth and minimum tillage at 0.20 m depth (MT) each of them carried out at two different soil water contents (WC) [low, 58% (LH) and high, 80% (HH) of field capacity] were investigated. The results obtained in this research show high values of soil strength in term of Penetration resistance (CI) and shear strength (SS) particularly in deeper soil layers at lower water content. Fossil-fuel energy requirements both for P40 LH and P20 LH were 25 and 35% higher with respect to the HH treatments and tractor slip were very high (P40 LH = 32.4%) with respect to the P40 HH treatment (16%). Therefore soil water content had significantly influenced tractor performance during soil ploughing, particularly at 0.40 m depth while MT was not influenced at all. A significant correlation between grain yield and soil penetration resistance was found highlighting how soil strength may be good indicator of its productivity. Obtained results during these field tests allowed considering MT and P20 treatments more suitable for this type of soil in climate change scenarios.

In this study, the determination of static E50 and υ parameters of rock materials was investigated using P-S wave velocities and Shore hardness (SH), non-destructive measurement methods. We used multiple linear regression (MLR), multiple non-linear regression (MNLR) and artificial neural network (ANN) models to estimate and determine these parameters. When the models defined by MLR, MNLR, and ANN were compared to the R2 values, ANN models that estimate E50 and υ parameters of rock materials using non-destructive methods (Vp, Vs, Vp/Vs, d, and SH) could be determined with higher accuracy than MLR and MNLR models. The study’s originality is based on the fact that ores such as galena, chromite, and barite have been studied for the first time on rock mechanics, and in this respect, it offers an innovative perspective. In addition, the use of all non-destructive measurement methods, Vp, Vs, and Shore hardness tests, also increases the originality of the study.

Moso bamboo is famous for fast growing and biomass accumulation, as well as high annual output for timber and bamboo shoots. These high outputs require high nutrient inputs to maintain and improve stand productivity. Soil nitrogen (N), phosphorus (P) and potassium (K) are important micronutrients for plant growth and productivity. Due to high variability of soils, analysing spatial patterns of soil N, P and K stocks is necessary for scientific nutrient management in Moso bamboo forests. In this study, soils were sampled from 138 locations across Yong’an City and ordinary kriging was applied for spatial interpolation of soil N, P and K stocks. Soil N stock showed a strong spatial dependence while soil N and P stocks presented a moderate spatial dependence, indicating soil N was mainly controlled by intrinsic factors while soil N and P stocks were controlled by both intrinsic and extrinsic factors. Different spatial patterns were observed for soil N, P and K stocks across the whole study area, indicating that fertilizations with different ratios of N:P:K should be applied for different sites to maintain and improve stand productivity. The total soil N, P and K stocks within 0-60 cm were 0.624, 0.020 and 0.583 Tg, respectively.

This paper presents the simplified and quick way to obtain an experimental measure of the modulus of elasticity(E) of a piece of metal rod using the Smartphone microphone and through the experimental configuration in mode of unsupport beam Euler-Bernoulli(E-B). To understand it, it is required to have knowledge about flexural vibration of E-B beams and to know the analysis of the spectogram of the audio signal. The methodology consists in measuring the flexural resonance frequency through an app installed on a Smartphone and using the E formula deduced from the E-B theoretical framework. The results of the experimental measurements have a discrepancy of less than 5% with respect to the factory value, for a carbon steel rod with circular cross section using the impact excitation technique. It describes the precision and accuracy of the experimental measurement. It is useful, because it helps to classify the materials in the Faculty of Engineering and it helps to make a more efficient quality control.

The use of Supplementary Cementitious Material (SCM) is widely used in production of sustainable concrete. Blended cements, incorporating SCM such as Pulverized Fly Ash (PFA) and Ground Granulated Blast Furnace Slag (GGBFS) have been widely used to reduce the cement contents and avoid adverse environmental impacts of CO2 produced during cement manufacturing. The analysis of various structural properties of concrete such as compressive strength, flexural strength and modulus of elasticity is important for its structural application. In this research, flexural strength of 100mmx100mmx500mm beams made from blended cement were tested under three curing conditions i.e. winter, summer and under water and the flexural strength was calculated using EN-12390-5 at the ages of 28 days and 56 days. For modulus of elasticity, concrete cylinders 150mmx300mm were tested as per procedure described in BS 1881-121(1983) at the age of 28 days. The compressive strength, flexural strength and modulus of elasticity for blended cement incorporating PFA and GGBFS has been increased under summer curing environment. The experimental values of Modulus of Elasticity are compared with the provision of BS 1881.

This study investigates the unique morphology and mechanical properties of multi-jet electrospun cashew gum (CG) when combined with high molecular weight polyethylene oxide (PEO) and glycerol. Cashew gum (CG) is an inexpensive, non-toxic polysaccharide derived from Anacardium occidentale trees. Initially, the electrospinnability of aqueous solutions of cashew gum alone or in combination with PEO was evaluated. It was found that cashew gum alone was not suitable for electrospinning; thus, adding a small quantity of PEO was needed to create the necessary molecular entanglements for fiber formation. By using a single emitter with a CG:PEO ratio of 85:15, straight and smooth fibers with some defects were obtained. However, additional purification of the cashew gum solution and the incorporation of glycerol as a plasticizer were necessary to produce defect-free straight and smooth fibers. Interestingly, when the optimized formulation was electrospun using multiple simultaneous emitters, thicker aligned fiber bundles were achieved. Moreover, the resulting oriented fiber mats exhibited unexpectedly high elongation at break at ambient conditions. These findings highlight the potential of this bio-polysaccharide-based formulation for non-direct water contact applications requiring elastic properties.

The formulation used by most of the studies on an elastic torus are either Reissner mixed formulation or Novozhilov's complex-form one, however, for vibration and some displacement boundary related problem of a torus, those formulations face a great challenge. It is highly demanded to have a displacement-type formulation for the torus. In this paper, I will carry on my previous work [ B.H. Sun, Closed-form solution of axisymmetric slender elastic toroidal shells. J. of Engineering Mechanics, 136 (2010) 1281-1288.], and with the help of my own maple code, I am able to simulate some typical problems and free vibration of the torus. The numerical results are verified by both finite element analysis and H. Reissner's formulation. My investigations show that both deformation and stress response of an elastic torus are sensitive to the radius ratio, and suggest that the analysis of a torus should be done by using the bending theory of a shell, and also reveal that the inner torus is stronger than outer torus due to the property of their Gaussian curvature. Regarding the free vibration of a torus, our analysis indicates that both initial in u and w direction must be included otherwise will cause big errors in eigenfrequency. One of the most intestine discovery is that the crowns of a torus are the turning point of the Gaussian curvature at the crown where the mechanics' response of inner and outer torus is almost separated.

The mechanisms of natural oscillations and resonance are described, considering the peculiarities of the transformation of elastic and kinetic energy in the implementation of the law of conservation of energy in local and integral volumes of the body, using the concept of mechanics based on the concepts of space, time and energy. When describing the motion in the Lagrange form, the elastic deformation energy of the particles is determined by the quadratic invariant of the tensor, whose components are the partial derivatives of Euler variables with respect to Lagrange variables. The increment of the invariant due to elastic deformation is represented as the sum of two scalars, one of which depends on the average value of the relative lengths of the edges of the particles in the form of an infinitesimal parallelepiped, the second is equal to the standard deviation of these lengths from the average value. It is shown that each of the scalars can be represented in the form of two dimensionless kinematic parameters of elastic energy, which participate in different ways in the implementation of the law of conservation of energy. One part of the elastic energy passes into kinetic energy and participates in the implementation of the law of conservation of energy for the body as a whole, considering external forces. The second part is not converted into kinetic energy but changes the deformed state of the particles in accordance with the equations of motion while maintaining the same level of the part of the elastic energy of the particles used for this. The kinematic parameters differ from the volume density of the corresponding types of energy by a factor equal to the elastic modulus, which is directly proportional to the density and heat capacity of the material and inversely proportional to the volume compression coefficient. Transverse, torsional, and longitudinal vibrations are considered free and under resonance conditions. The mechanisms of transformation of forced vibrations into their own after the termination of external influences and resonance at the superposition of free and forced vibrations with the same or similar frequency are considered. The formation of a new free wave at each cycle with an increase in the amplitude, which occurs mainly due to internal energy sources, and not external forces, is justified.

Understanding the physical properties of ultramafic rocks is important for evaluating awide variety of petrologic models of the oceanic lithosphere, particularly upper mantle and lower crust. Hydration of oceanic peridotites results in increasing serpentine content, which affects lithospheric physical properties and the global bio/geochemical cycles of various elements. In understanding tectonic, magmatic and metamorphic history of the oceanic crust, interpreting seismic velocities, rock composition and elastic moduli are of fundamental importance. In this study we show that as serpentine content increases, density decreases linearly with a slope of 7.85. We also correlate increase in serpentine content with a linear decline in shear, bulk and Young’s moduli with slopes of 0.48, 0.77, 0.45 respectively. Our results show that increase in serpentine content of lower crust and forearc mantle could decrease elasticity of lithospehere and result in break-offs. Therefore tectonic processes at peridotite rich slow spreading ridges may be strongly affected by serpentine content, particularly serpentinization may be responsible for discontinuities in thin crust, and formation of weak fault zones.

In data-scarce regions, prudent planning and precise decision-making for sustainable development especially in agriculture remains a challenging task due to the lack of correct information. Remotely sensed satellite images provide a powerful source for assessing land use land cover (LULC) classes and crop identification. Applying Remote Sensing (RS) in conjunction with the Geographical Information System (GIS) and modern tools/ algorithms of artificial intelligence (AI) and deep learning has been proven effective for strategic planning and integrated resources management. The (this)study was conducted in the canal command area of the Lower Chenab Canal system in Punjab, Pakistan. Crop features/ classes were assessed using the Normalized Difference Vegetation Index (NDVI) algorithm. The MODIS (Moderate Resolution Imaging Spectroradiometer) 250 m and Landsat 5 TM (thematic mapper) images were deployed for NDVI time-series analysis with unsupervised classification technique to get LULC classes that helped to discern cropping pattern, crop rotation, and the area of specific crops, which were then used as a key input for agricultural mechanization planning and resources management. The accuracy of the LULC map was 78%, assessed by the error matrix approach. Limitations of high-resolution RS data availability and the accuracy of the results are the concerns observed in this study that could be managed by the availability of good quality local sources and advanced techniques of processing, which will make it more useful and applicable for regional agriculture and environmental management.

The isotopic and nuclear techniques discussed, namely: Fallout Radionuclide, Fingerprint, and Isotope Hydrology, are linked to the evaluation of soil and water degradation processes. A traditional literature review was conducted to gain the most comprehensive understanding of both the current state of the art and the subject matter, with the aim of proposing a hypothesis that integrates the synergistic convergence of these techniques in order to offer results that are more reliable. A case study is presented as a synthesis of the preceding discussion.

The substitution of chemical fertilizers by organic manure plays a critical role in sustainable crop production. Nevertheless, organic amendments promote the global warming potential (GWP) in rice paddies due to increased methane (CH4) emissions. Increasing evidence shows that lime application can reduce CH4 emissions from acidic paddy soils, while it is still not clear whether liming can reduce the GWP in rice fields under organic manure substitution. A two-year field experiment was conducted to investigate the impacts of pig manure substitution and lime application on grain yield, CH4 and nitrous oxide (N2O) emissions in a subtropical double-cropped rice field in China. The experiment consisted of three treatments: chemical fertilization (CF, 100% N from urea), 50% of chemical N substituted by pig manure (1/2N + M), and the 1/2N + M treatment plus lime amendment (1/2N + M + L). On average, 1/2N + M reduced rice yield by 5.65% compared to CF, while lime application had no effect on rice yield. Mean cumulative CH4 emissions were 218.8% higher in 1/2N + M than in CF, whereas 1/2N + M + L reduced CH4 emissions by 36.6% compared to 1/2N + M. Neither pig manure substitution nor lime application affected N2O emissions. Consequently, 1/2N + M increased the GWP and greenhouse gas intensity (GHGI) by 214.6% and 228.3%, respectively, compared to CF. In contrast, 1/2N + M + L reduced the GWP and GHGI by 36.4% and 36.5% compared to 1/2N + M. Lime application can mitigate CH4 emissions and GWP induced by pig manure amendment in double-cropped rice fields.

Detecting and monitoring changes in soil salinity through remote sensing provides an opportunity for field assessment in regions where on-site measurements are limited. This investigation, carried out in Siwa Oasis, Egypt, aimed to assess the efficacy of several soil salinity indices derived from Landsat 5 and 7 satellite images. To achieve this, 56 on-site ground measurements were utilized for evaluation purposes. The study aimed to improve the correlation between EC and index values and explore the relationship between salinity and changes in land cover. Eleven spectral indices were calculated for nine scenes captured in different months from August to December. The first approach involved stacking the data to identify the index with the strongest correlation with ground EC values, without the need for complex analysis or EC value ranging. In the second approach, the ground EC measurements were classified into seven different salinity categories, and the correlation coefficient was calculated between each index and each salinity category. The third approach analyzed the data temporally, considering different salinity levels. Lastly, a spatial correlation analysis was conducted between EC and index values in the fourth scenario. The initial approach revealed a weak correlation due to substantial variation in EC values. However, the SI index demonstrated the highest correlation coefficient of 0.38. In the second scenario, the S2 index exhibited the highest correlation of 0.96 for moderate salinity samples. The third scenario showed that the S1 index achieved the highest correlation value of 0.99 for moderately saline areas. In the fourth scenario, the SI index exhibited the strongest correlation among all four ponds with correlation coefficients of 0.23, 0.23, 0.18, and 0.61. Notably, the correlations observed in the second and third scenarios demonstrated higher correlation coefficients compared to both the first and fourth scenarios. The study highlighted significant variations in EC levels related to land cover types and pond elevation. Additionally, remote sensing methods detected a 48% increase in total vegetated area over 17 years, showing the potential of remote sensing techniques in salinity monitoring for expanding agriculture and improving land management.