Emerging pollutants as pharmaceuticals have been focusing international attention for few decades. Ciprofloxacin (CIP) is a common drug widely found in effluents from hospitals, industrial and different wastewater treatment plants, as well as rivers. In this work, the lab-scale 3D-BER system was established, and more than 90% of the antibiotic CIP removal from the Low C/N wastewater. Best results were obtained with current intensity, and different C/N ratio significantly improve the removal of CIP and nitrates, when the ideal conditions were; C/N = 1.5-3.5, pH =7.0-7.5, and I = 60 mA. The highest removal efficiency of CIP = 94.20 %, NO3--N= 95.53 % and total nitrogen (TN) = 84.27 %, respectively. In this novel system, the autotrophic-heterotrophic denitrifying bacteria played vital role for the removal of CIP and enhanced denitrification process. Thus, autotrophic denitrifying bacteria uses CO2 and H2 as carbon sources to reduce nitrates to N2. This system has the assortment and prosperous community revealed at the current intensity of 60 mA, and the analysis of bacterial community structure in effluent samples fluctuates under different condition of C/N ratios. According to the results of LC-MS/MS analysis, the intermediate products were proposed after efficient biodegradation of CIP. Microbial community on biodegrading was mostly found at phylum, and class level was dominantly responsible for the NO3--N and biodegradation of CIP. This work can provide some new insights towards the biodegradation of CIP and the efficient removal of nitrates from low C/N wastewater treatment by the novel 3D-BER system.

The utilization of titanium dioxide (TiO2) as a photocatalyst for the treatment of wastewater has attracted significant attention in the environmental field. Herein, we have prepared a NH2-MIL-125-derived TiO2@N-doped C Visible Light Catalyst through an in-situ calcination method. The nitrogen element in the organic connector is released through calcination, simul-taneously doping into the sample, thereby enhancing its spectral response to cover the visible region. The as-prepared TiO2@N-doped C catalyst exhibited preserved cage structure even after calcination, thereby alleviating the optical shielding effect and further augmenting its photo-catalytic performance by increasing the reaction sites between the catalyst and pollutants. The calcination time of the TiO2@N-doped C-450 °C catalyst was optimized to achieve a balance be-tween the TiO2 content and nitrogen doping level, ensuring efficient degradation rates for basic fuchsin (99.7%), Rhodamine B (89.9%), and tetracycline hydrochloride (93%) within 90 minutes.

The European Parliament had adopted legislative resolution of 10 April 2024 on the proposal for a directive of the European Parliament and of the Council concerning urban wastewater treatment. The reduction of pollution in discharged treated wastewater in the parameters of BOD5, total ni-trogen and total phosphorus was emphasized. Based on these results, it stated that the impacts on the quality of lakes, rivers and seas in the EU are visible and tangible. At the same time, it was emphasized that the sector of urban wastewater removal and treatment is responsible for 0.8% of the total electricity consumption and about 0.86% of all greenhouse gas emissions in the entire EU. Almost a third of these emissions could be prevented by improving the treatment process, better use of sewage sludge and increasing energy efficiency, as well as a higher rate of use of renewable resource technologies. It is also necessary to better integrate treatment processes into the circular economy. Sludge management and water reuse is sub-optimal as too many valuable resources are still being wasted. This review article is focused on sustainable municipal wastewater treatment, innovative and new wastewater treatment processes and technologies (combined and hybrid processes, Anammox, etc. and their use in practice with the aim of increasing environmental and energy efficiency and reducing the carbon footprint. The research is focused on the possibilities of increasing the efficiency of energy processing of sludge, reuse of nitrogen and phosphorus, sludge and reuse of treated wastewater.

Copper-catalyzed and organocopper-involved reactions are of great significance in organic synthesis. To have a deep understanding of the reaction mechanisms, the structural characterizations of organocopper intermediates become indispensable. Meanwhile, the structure-function relationship of organocopper compounds would advance rational design and development of new Cu-based reactions and organocopper reagents. Compared to the mono-carbonic ligand, the C,N- and C,C-bidentate ligands better stabilize the unstable organocopper compounds. The bidentate ligands can chelate to the same copper atom via ?2-mode, forming a mono-cupra-cyclic compounds with at least one acute C-Cu-C angle. When the bidentate ligands bind to two copper atoms via ?1-mode at each coordinating site, the bimetallic macrocyclic compounds will form nearly linear C-Cu-C angles. The anionic coordinating sites of the bidentate ligand can also bridge two metals via ?2-mode, forming organocopper aggregates with Cu-Cu interactions and organocuprates with contact ion pair structures. The reaction chemistry of some selected organocopper compounds is highlighted, showing their unique structure-reactivity relationships.

Water pollution, intensified by the release of hard-to-degrade pollutants, poses severe threats to ecosystems, human health, and economic development. The existing advanced oxidation processes often involve high operational costs and may result in secondary pollution, highlighting the necessity for innovative and more sustainable solutions. To address these challenges, our study introduces a cost-effective and eco-friendly corona discharge barrier plasma discharger for wastewater treatment. Through the central composite design/response surface methodology, a high decolorization rate of 98% of methylene blue (MB) within 10 minutes was achieved by optimizing parameters such as pH and voltage. Furthermore, the mechanisms of the generation of reactive oxygen species via this device was discussed in detail and the degradation pathways of MB were described. Moreover, this device is also very energy-efficient, with a low energy density and electrical energy per order of 0.15 watt/mL and 5.79 kWh/m³/order, respectively. In conclusion, the plasma discharger developed in this study provides a cost-effective and environmentally sustainable solution for dye wastewater treatment. This research contributes significantly to the advancement of sustainable dye wastewater management practices, offering an innovative method that meets both environmental and economic objectives.

A series of dinuclear copper(I) N,C,N- and P,C,P-carbodiphosphorane (CDP) complexes using multidentate ligands CDP(Py)2 (1) and (CDP(CH2PPh2)2 (13) have been isolated and characterized. Detailed structural information was gained by single crystal XRD analyses of nine representative examples. The common structural motive is the central double ylidic carbon atom with its characteristic two lone-pairs involved into binding of two geminal L-Cu(I) fragments at Cu-Cu distances in the range 2.55 – 2.67 Å. In order to enhance conformational rigidity within the characteristic Cu-C-Cu triangle, two types of chelating side arms were symmetrically attached to each phosphorus atom: two 2-pyridyl functions in ligand CDP(Py)2 (1) and its dinuclear copper complexes 2-9 and 11, as well as two diphenylphosphinomethylene functions in ligand CDP(CH2PPh2)2 (13) and its di- and mononuclear complexes 14-18. Neutral complexes were typically obtained via reaction of 1 with Cu(I) species CuCl, CuI, and CuSPh or via salt elimination reaction of [(CuCl)2(CDP(Py)2] (2) with sodium carbazolate. Cationic Cu(I) complexes were prepared upon treating 1 with two equivalents of [Cu(NCMe)4]PF6, followed by the addition of either two equivalent of an aryl phosphine (PPh3, P(C6H4OMe)3) or one equivalent of a bisphosphine ligands DPEPhos, XantPhos or dppf. For the first time carbodiphosphorane CDP(CH2PPh2)2 (13) could be isolated upon treating its precursor [CH(dppm)2]Cl (12) with NaNH2 in liquid NH3. A protonated and a deprotonated derivative of ligand 13 were prepared and their coordination was compared to neutral CDP ligand 13. NMR analysis and DFT calculations reveal, that the most stable tautomer of 13 does not show a CDP (or carbone) structure in its uncoordinated base form. For most of the prepared complexes, photoluminescence upon irradiation with UV light at room temperature was observed. Quantum yields (PL) were determined to 36% for dicationic [(CuPPh3)2(CDP(Py)2)](PF6)2 (4) and to 60% for neutral [(CuSPh)2(CDP(CH2PPh2)2] (16).

Preventing the rebound of black and odorous water bodies is critical for improving the ecological environment of water bodies. This study investigated the effect and mechanism of in-situ improvement of sediment microenvironment by nitrate in tailwater of wastewater treatment plants combined with aerobic denitrifying bacteria under low-DO regulation (TailN+CFM+LDO). On the 60th day of remediation, the dissolved oxygen and oxidation-reduction potential in the overlying water increased to 5.6 mg/L and 300 mV, respectively, the acid volatile sulfide in the sediment decreased by 70.4%, and the organic matter in the sediment was reduced by 62.7%, in which the HFOM was degraded from 105 g/kg to 56 g/kg, and the potential risk of water reverting to black and odorous conditions significantly decreased. Amplicon sequencing analysis revealed that the relative abundance of electroactive bacteria Thiobacillus and Pseudomonas with denitrification capacity was found to be significantly higher in the TailN+CFM+LDO group than in the other remediation groups. Functional prediction of 16S sequencing results indicated that both the quantity and activity of critical microbial enzymes involved in nitrification and denitrification processes could enhance in the TailN+CFM+LDO group. These results improved our understanding of the improvement of the sediment microenvironment and could thus facilitate its application.

Preventing the occurrence of secondary caries serves as one of the significant issues in dental clinic, thus make it indispensable to improving the properties of conventional composite resin (CR) by developing a novel CR. In present study, two groups of experimental CRs loaded with different contents of fluoride-doped nano-zirconia fillers (25 wt% and 50 wt%) were fabricated. The surface topography, mechanical performance, fluoride release, antibacterial effect, aging property and cytotoxicity of the experimental CRs were evaluated subsequently. A uniform distribution of the F-zirconia fillers over the whole surface of resin matrix could be observed. The experimental CRs showed continuous fluoride release within 28 days, which was positively correlated with the content of F-zirconia fillers. Moreover, the amount of fluoride release increased in the acidic buffer. Addition of F-zirconia fillers could improve the color stability, wear resistance and microhardness of the experimental CRs, without reducing the flexure strength. Furtherly, the fluoride ions released continuously from the experimental CRs resulted in effective contact and antibacterial properties, while they showed no cytotoxicity. As a consequence, considerations can be made to employ this new kind of composite resin loaded with fluoride-doped nano-zirconia fillers to meet clinical requirements when the antimicrobial benefits are desired.

Livestock farming plays a crucial role in agriculture and is important in meeting people's needs for a better life in the new era. However, due to China's "double carbon" target, the development of animal husbandry has been affected by the level of carbon emissions. To study the spatial dis-tribution and dynamic evolution of livestock carbon emissions in Shandong Province, we used panel data from 16 prefecture-level cities in Shandong Province from 2001 to 2022 to determine the spatial differentiation of livestock carbon emissions in Shandong Province and their dynamic evolution by combining spatial and non-parametric estimation methods based on livestock carbon emissions and livestock emission intensity measured by city. The results of the study show that the distribution of carbon emissions from animal husbandry in Shandong Province is in a "dis-persed-aggregated" pattern, and the intensity of carbon emissions shows a gradual downward trend, with a ladder-like distribution characterized by high in the west and low in the east. Through the analysis of the dynamic evolution of nuclear density, we observe that the regional differences of animal husbandry carbon emissions in Shandong Province are expanding, showing the characteristics of polarization. The difference of carbon emissions in the peninsula is gradually narrowing, and the phenomenon of polarization is weakening. The carbon emissions of animal husbandry in the central and western regions of Shandong are polarized.

The per capita availability of freshwater resources on a global scale is gradually decreasing due to population growth, rapid urbanization, industrialization, and modern lifestyles. In this situation, wastewater management becomes a major concern. Conventional treatment processes used to treat wastewater discharges are not adequate for the advanced removal of pollutants, especially refractory organic pollutants, which are mainly organic compounds that are not easily biodegradable in the environment. The use of photocatalytic membrane reactors (PMRs) for tertiary wastewater treatment has attracted much interest in recent periods, and various configurations have been investigated. The performance of a PMR using an iron doped titanium photo catalyst and Polysulfone-based polymeric membrane for municipal wastewater treatment was evaluated under natural and simulated solar light. Obtained results proved that solar driven PMRs can remove organic loading (COD) with high efficiencies and may represent a suitable alternative for the tertiary treatment step of municipal wastewater.

Let $n \geq 2$ be a fixed integer and $\mathcal{A}$ be a $C^*$-algebra. A permuting $ n $-linear map $ \mathcal{G} : \mathcal{A} ^{n} \rightarrow \mathcal{A} $ is known to be symmetric generalized $n$-derivation if there exists a symmetric $n$-derivation $ \mathfrak{D} : \mathcal{A} ^{n} \rightarrow \mathcal{A} $ such that $ \mathcal{G} \left(x_{1}, x_{2}, \ldots, x_{i} x_{i}^{\prime}, \ldots, x_{n}\right)= \mathcal{G} \left(x_{1}, x_{2}, \ldots, x_{i}, \ldots, x_{n}\right) x_{i}^{\prime}+x_{i} \mathfrak{D} (x_{1}, x_{2},\ldots, x_{i}^{\prime}, \ldots, x_{n})$ holds for all $x_{i}, x_{i}^{\prime} \in \mathcal{A} $. In this paper, we investigate the structure of $C^*$-algebras involving generalized linear $n$-derivations. Moreover, we describe the forms of traces of linear $n$-derivations satisfying certain functional identity.

This study aims to evaluate the effectiveness of inactivating Salmonella enteritidis in fresh chicken breast by irradiation using a combination of short-wave UV (0, 3, 6, 9, 12 and 15 J / cm2) and a natural antimicrobial such as caffeine (0, 5, 10, 15 and 20 nM/g) as alternative proposals to conventional techniques to reduce pathogens in food. The temperatures used were from 2 to 22°C. The most suitable models were double Weibull in 60% of cases with an adjustment of R2 0.9903-0.9553 and Weibull + cola, in 46.67%, with an adjustment of R2 of 0.9998-0.9981. Noting that the most effective combination in the reduction of Salmonella was 12 J/cm2 of UV light and 15 nM/g of caffeine, with a reduction of 6 CFU/g and an inactivation rate of 0.72. The synergistic effect was observed by increasing caffeine and UV light. Furthermore, the physic-chemical characteristics of the food matrix were not affected by the combination of both technologies. Therefore, these results suggest that this combination can be used in the food industry to effectively inactivate Salmonella enteritidis, without deteriorating product quality.

This study surveyed the variation in Perfluorinated Compounds (PFCs) concentration entering urban wastewater treatment plants and proposed an optimal PFCS treatment method. The PFCS concentration in influent was shown to be affected by the types of industries and operating rate. The concentration of PFCs in the wastewater treatment effluent was slightly lower than that of influent. Thus, PFCs were considered to have barely been removed by the existing biological treatments. The pilot test result showed that about 10% of PFCs were removed by coagulation and precipitation, and the ozone and chlorine test also showed that few PFCs were removed regardless of the amount of injection. The activated carbon adsorption test showed that the removal was significantly increased by the empty bed contact time, with about a 60% removal in five minutes and over a 90% removal in 15 minutes. Therefore it is determined that a more stable and higher PFCs removal would result from the continuous oxidation processes such as ozone and adsorption processes such as activated carbon rather than a single biological treatment.

Electrochemical methods are used for the treatment of both municipal and industrial wastewater, either independently or in conjunction with biological methods. This conjunction is used for pretreatment or posttreatment of biologically treated wastewater. In our work, we focused on the combination of these processes, where pre-electrolysis was used to produce dissolved iron before the activation process. Electrolysis was also directly introduced into the activation using either iron or carbon electrodes. The surface of one iron electrode was 32.2 cm2, the applied voltage was 21 V, and the supplied current was 270 mA. The surface of one carbon electrode was 7.54 cm2, the supplied current was 82.5 mA, and the applied voltage was 21 V. From laboratory research on the treatment of synthetic municipal wastewater using a combination of electrolysis and activation processes, it resulted that the use of iron electrodes increased the efficiency of phosphorus removal compared to its precipitation with iron salts. The electrolysis had a positive effect on the sedimentation properties of sludge and the destruction of filamentous microorganisms. Electrolysis negatively affected the respiration rates of activated sludge and the efficiency of denitrification. However, it did not have a negative impact on the nitrification activity of the sludge.

Piggery wastewater (PWW) is characterized by its high concentrations of organic matter and ammonium, and by their odour nuisance. Traditionally, PWW has been treated in open anaerobic lagoons, anaerobic digesters and activated sludge systems, which exhibit high greenhouse gas emissions, a limited nutrients removal and a high energy consumption, respectively. Photosyn-thetic microorganisms can support a sustainable PWW treatment in engineered photobioreactors at low operating costs and with an efficient recovery of carbon, nitrogen and phosphorous. These microorganisms are capable of absorbing solar irradiation through the photosynthesis process to obtain energy, which is used for their growth and associated carbon and nutrients assimilation. Purple phototrophic bacteria (PPB) represent the photosynthetic microorganisms with the most versatile metabolism in nature, while microalgae are the most studied photosynthetic microor-ganisms in recent years. This review describes the fundamentals, symmetry and asymmetry of PWW treatment using photosynthetic microorganisms such as PPB and microalgae. The main photobioreactor configurations along with the potential of PPB and microalgae biomass valori-zation strategies are also discussed.

Microalgae wastewater treatment has long been promoted as a sustainable method to handle the influx of human waste due to population growth. Initially, in the early 1900’s, microalgae was noted to increase wastewater treatment efficiency by aerating the water and consuming waste. By mid-century, wastewater grown microalgae was being investigated as a way to produce biomass for food, fuel, and other biomaterials. The space race in the 1960’s led to the use of microalgae in life support systems. Technological developments and political pressure in the 1970’s spurred studies of the impact of wastewater on the growth of phytoplankton in the oceans as well as methods to use microalgae wastewater treatment in aquaculture. Simultaneously, the oil crisis of that decade promoted research of alternative fuels, which included microalgae biofuels via the Aquatic Species Program. This program led to research into the use of wastewater as a feedstock for microalgae growth. By the later 2000’s, instability in the oil market caused another energy crisis which further prompted investment in microalgae biofuels, some of which involved combined wastewater treatment. Currently, microalgae wastewater treatment is being researched as a way to cut back on greenhouse gas emissions to curb global warming and produce sustainable biofuels.

Wet coffee processing methods will produce wastewater containing organic matter. The high content of organic matter can be utilized as biogas through the anaerobic process. Anaerobic digesters construction can affect removal process of wastewater pollution and biogas quantity. The purpose of this study is to determine the effect of digester construction between conventional digester, CSTR and UASB producing biogas from coffee wastewater. The conventional digester worked without temperature control system as control, a UASB digester, and CSTR digester worked with temperature control system. Biomass volume was about 5 L with 35 days incubation time. Temperature and pH for UASB and CSTR were set within the range 30 – 35^oC and pH 6.0 – 8.0. Based on the feeding variations, UASB has a stable performance with 83.57 ml/day of average biogas production. It has also highest remediation efficiency of COD, BOD and C/N with 85.00±0.34 %, 84.40%± 5.66 and 97.78± 0.57.

This work aimed to develop an anionic cellulose nanofiber (CNF) bio-adsorbent from palm date tree waste and to investigate its removal efficiency against cationic methylene blue dye from contaminated water. Palm date pulp was first prepared from palm date leaves through acid hydrolysis using H2SO4, followed by hydrolysis in a basic medium using KOH, in which the process completely removed the components of hemicellulose, lignin, and silica. To obtain anionic CNF, the resulting pulp was further treated with H2SO4, followed by centrifugation. Biogel formation of the CNF suspension was promoted by sonication, where its removal efficiency of methylene blue dye was studied as a function of dye concentration, temperature, contact time, and pH value. Two equilibrium models, the Langmuir and Freundlich models were employed, and the Langmuir model was found to be consistent with the experimental data. The highest removal efficiency was obtained at 60oC and was 5mg/gm. Furthermore, several kinetic models were used to gain insight into the adsorption mechanism. The pseudo-second-order model provided an accurate description of the adsorption process, while the Elovich equation suggested a chemical reaction between methylene blue dye and CNF. The study’s findings were in agreement with the pseudo-second-order model, indicating general chemical reactions. The study indicates that CNF adsorbents derived from renewable natural waste sources such as palm date leaves can be effective in removing cationic contaminants such as methylene blue dye.

The existences of the N→C dative bonds in the complexes between N-containing molecules and fullerenes have been verified both theoretically and experimentally. However, finding stable N→C dative bonds is still a highly challenging task. In this work, we investigated computationally the N→C dative bonds in the complexes formed by fullerene C60 with 1,2,5-chalcogenadiazoles, 2,1,3-benzochalcogenadiazoles and 1,2,4,5-chalcogenatriazoles, respectively. It was found that the N→C dative bonds are formed along with the formation of the N–Ch···C (Ch = S, Se, Te) chalcogen bonds. In the gas phase, from S-containing complexes through Se-containing complexes to Te-containing complexes, the intrinsic interaction energies become more and more negative, which indicates that the N–Ch···C chalcogen bonds can facilitate the formation of the N→C dative bonds. The intrinsic interaction energies are compensated by the large deformation energy of fullerene C60. The total interaction energies of Te-containing complexes are negative, while both of the total interaction energies of S-containing complexes and Se-containing complexes are positive. This means that the N→C dative bonds in the Te-containing complexes are more easily observed in experiments in comparison with those in the S-containing complexes and Se-containing complexes. This study provides a new theoretical perspective on the experimental observation of the N→C dative bonds in the complexes involving fullerenes. Further, the formation of stable N→C dative bonds in the complexes involving fullerenes can significantly change the properties of fullerenes, which will greatly simulate and expand the application range of fullerenes.

Stroke is the number one cause of morbidity in the United States and number two cause of death worldwide. There is a critical unmet medical need for more effective treatments of ischemic stroke, and this need is increasing with the shift in demographics to an older population. Recently, several studies have reported the therapeutic potential of stem cell derived exosomes as new candidates for cell-free treatment in stoke. This review focuses on the use of stem cell-derived exosomes as a potential treatment tool for stroke patients. Therapy using exosomes can have a clear clinical advantage over stem cell transplantation in terms of safety, cost, and convenience, as well as reducing bench-to-bed latency due to fewer regulatory milestones. In this review article, we focus on 1) the therapeutic potential of exosomes in stroke treatment, 2) the optimization process of upstream and downstream production, and 3) preclinical application in stroke animal model. Finally, we discuss the limitations and challenges faced by exosome therapy in future clinical applications.

The bivalve mollusc Pinna nobilis, endemic to the Mediterranean Sea, since 2016 is vanishing from the whole basin because of an infection by multiple pathogens that caused mass mortality events. In the Eastern Mediterranean some little populations seem to be resistant to the infection. These individuals could represent the only possibility for the species to recolonize now desert habitats. Thus, according to the recommendations of IUCN, the looking for living specimens of P. nobilis is a priority. As a result of a monitoring activity carried out in 2022-2024, along the Ionian cost of Apulia, in Southern Italy, the species has completely disappeared leaving only empty shells. Concurrent to the vanishing of P. nobilis, its congeneric P. rudis, resistant to the infection, seems to be taking advantage, becoming more common and colonizing habitats once exclusive of P. nobilis. In fact, from different areas of the Mediterranean, the sightings of P. rudis are increasing, together with the discovering of individuals exhibiting morphological traits that are a mixing between the two species. In some cases, these morphological features are not easy to detect, anyway the presence of these hybrids, resistant to the infection, is important for the conservation of the species.

Neurodegenerative diseases (NDDs) are a class of cognitive and motor disorders that include Alzheimer’s disease (AD), Parkinson’s disease (PD), Huntington's disease (HD), amyotrophic lateral sclerosis (ALS), and others. They are caused by lesions in cells and tissues of the central nervous system, resulting in corresponding dysfunctions and consequent decline in cognitive and motor functions. Neural tissues are extremely vulnerable to oxidative stress, which plays critical biological roles in NDDs. Aromatic compounds are found extensively in natural plants and have substantial effects of anti-oxidative stress damage, which not only have a wide range of research applications in cosmetics, foods, etc., but are also frequently utilized in the treatment of various central nervous system diseases. This review summarizes the relevant oxidative stress mechanisms in NDDs (AD, PD, HD, and ALS) and reviews aromatic compounds such as polyphenols, terpenoids, and flavonoids that can be used in the management of neurodegenerative diseases, as well as their specific mechanisms of antioxidant action. This review will serve as a reference for future experimental studies on neurodegenerative illnesses while also offering fresh insights into clinical therapy.

An extensive thermodynamic study of N-methylformamide (CAS RN: 123-39-7) and N,N-dimethylformamide (CAS RN: 68-12-2), is presented in this work. The liquid heat capacities of N-methylformamide were measured by Tian–Calvet calorimetry in the temperature interval (250 – 300) K. The vapor pressures for N-methylformamide and N,N-dimethylformamide were measured using static method in the temperature range 238 K to 308 K. The ideal-gas thermo-dynamic properties were calculated using a combination of the density functional theory (DFT) and statistical thermodynamics. A consistent thermodynamic description was developed using the method of simultaneous correlation, where the experimental and selected titerature data for vapor pressures, vaporization enthalpies, and liquid phase heat capacities and calculated ide-al-gas heat capacities are treated together to ensure overall thermodynamic consistency of the results. Resulting vapor pressure equation is valid from the triple point to the normal boiling point temperature.

Solid polymer electrolytes and composite polymer electrolytes serve as crucial components in all-solid-state energy storage devices. Structural batteries and supercapacitors present a promising alternative for electric vehicles, integrating structural functionality with energy storage capability. However, despite their potential, these applications are hampered by various challenges, particularly in the realm of developing new solid polymer electrolytes that require more investigations. In this study, novel solid polymer electrolytes and composite polymer electrolytes were synthesized using epoxy resin blends, ionic liquid, lithium salt, and alumina nanoparticles, and subsequently characterized. Among the formulations tested, the optimal system, designated as L70P30ILE40Li1MAl2 and containing 40 wt.% of ionic liquid and 5.7 wt.% of lithium salt, exhibited exceptional mechanical properties. It displayed a remarkable storage modulus of 1.2 GPa and reached ionic conductivities of 0.085 mS/cm at 60°C. Furthermore, a proof-of-concept supercapacitor was fabricated, demonstrating the practical application of the developed electrolyte system.

Today major environmental issue facing the universe is Industrial wastewater. They are present in the form of various pollutants like organic/inorganic, heavy metals, and non-disintegrating materials at an enormous amount. As of now, eliminating these pollutants from wastewater from industries in a viable manner has become a significant issue. Productive refinement methodologies are required to eliminate those toxins before removal. Furthermore, nanomaterials are innovationally powerful to purification of water by utilizing inexpensive nanofiltration and nano adsorbent. Heavy metal ions removal in an efficient way from the environment is the first and foremost problem from a biological and ecological perspective, and numerous research practices have been dedicated to the removal of harmful metal particles, involved both in the underground and surface wastewater. This article mainly focuses on the nanomaterials utilization of various contaminating materials removal from industrial wastewater with an exceptional spotlight on rare earth components and nanofiber and nanocomposite films. The objective is to offer references an outline in the field of developing nanomaterials utilization for harmful pollutants removal from industrial wastewater for industrializers and analysts.

Background: this interventional pilot study aimed to evaluate the short-term (3 years) efficacy of focal laser ablation (FLA) in treating the index lesion of low-intermediate risk prostate cancer, along with assessing the safety of the procedure (ClinicalTrials.gov ID NCT04045756). Methods: forty patients aged between 46 and 86 with histologically proven organ-confined prostate cancer and low to intermediate progression risk were included. FLA was performed under percutaneous fusion magnetic resonance/ultrasound guidance in a Day Hospital setting under local anesthesia. Patients underwent regular clinical assessments, PSA measurements, post-procedure MRI scans, and biopsies at 36 months or if positive findings were detected earlier. Statistical analyses were conducted to assess trends in PSA levels and cavity dimensions over time. Results: forty patients were initially included, with 15 lost to follow-up. At 36 months, a mean PSA reduction of 60% was observed, and 80% of MRI scans showed no signs of in-field clinically significant residual/recurrent cancer. Biopsies at 36 months revealed no malignant findings in 20 patients. No deterioration in sexual function or urinary symptoms was recorded. Conclusions: FLA appears to be safe, feasible and effective in the index lesion treatment of low-intermediate risk prostate cancer, with a high rate of tumor eradication and preservation of quality of life.

In recent years, the discharge of various emerging pollutants, chemicals and dyes in water and wastewater has represented one of the prominent human problems. Since water pollution is directly related to human health, highly resistant and emerging compounds in aquatic environments will pose many potential risks to the health of all living. Therefore, water pollution is a very acute problem that has constantly increased in recent years with the expansion of various industries. Consequently, choosing efficient and innovative wastewater treatment methods to remove contaminants is crucial. Among advanced oxidation processes, electrochemical oxidation (EO) is the most common and effective method for removing persistent pollutants from municipal and industrial wastewater. However, there are still many gaps despite the great progress in using EO to treat real wastewater. This is due to the lack of comprehensive information on the operating parameters which affect the process and its operating costs. In this paper, among various scientific articles, the impact of operational parameters on the EO performances, a comparison between different electrochemical reactor configurations, and a report on general mechanisms of electrochemical oxidation of organic pollutants have been reported. Moreover, an evaluation of cost analysis and energy consumption requirements have also been discussed. Finally, the combination process between EO and another important advanced oxidation technology, PEC, called photoelectrocatalysis (PEC), has shortly been discussed and reviewed. This article showed that there is a direct relationship between important operating parameters with the amount of costs and the final removal efficiency of emerging pollutants. Optimal operating conditions can be achieved by paying special attention to reactor design, which can lead to higher efficiency and more efficient treatment. The rapid development of EO for removing emerging pollutants from impacted water and its combination with other green methods can result in more efficient approaches to face the pressing water pollution challenge.

An analysis of the processes of plastic deformation and acoustic relaxation in a high-entropy alloy Al0.5CoCrCuFeNi was carried out. The following have been established: dominant dislocation defects; types of barriers that prevent the movement of dislocations; mechanisms of thermally activated movement of various elements of dislocation lines through barriers at room and low temperatures. Based on modern dislocation theory, quantitative estimates have been obtained for the most important characteristics of dislocations and their interaction with barriers.

Microwave absorbers with lightweight, good stability and high efficiency have attracted much attention for their applications in many contemporary fields. In this work, the 3D porous (Ni@NO-C)n/NO-C composite absorber was prepared by a wet chemistry method with Ni chains and melamine as precursors, in which NO-C (N,O-doped carbon) encapsulated Ni particles are homogenously dispersed in the 3D porous networks of NO-C in the form of (Ni@NO-C)n chains. The special microstructure of the as-prepared material is proved to be benefit for the improvement of its microwave adsorption performance. The as-synthesized (Ni@NO-C)n/NO-C composite ab-sorber exhibited an effective absorption bandwidth of 4.1 GHz and an extremely large reflection loss of -72.3 dB. The excellent microwave absorbing performances can be ascribed to the coopera-tive consequence of dielectric loss and magnetic loss along with the balance between attenuation capability and impedance match.

The treatment of petroleum refinery wastewater (PRWW) is of great interest in the field of industrial wastewater management. The wastewater contains a diverse concentration of contaminants such as oil and grease, petroleum hydrocarbons, phenol, ammonia, sulfides, as well as other organic and inorganic composites etc. The treatment of refinery wastewater has been treated through various processes including; physical, biological, chemical or hybrid methods which combine two or more techniques. Hence, the objective of this review is to summarize the recent research studies applied in the treatment of petroleum refinery wastewater using conventional, advanced as well as integrated treatment techniques. Furthermore, critically highlight the efficiencies and major limitations of each technique as well as prospects for improvement. Several conventional treatment techniques (basically, the physicochemical and biological processes) were discussed. In this context, advanced oxidation processes (AoPs) especially electrochemical oxidation and photocatalysis as well as the integrated/hybrid processes are found effective to remove the recalcitrant fraction of organic pollutants because of their various inherent mechanisms. These techniques could effectively remove COD and phenols concentration with an average removal efficiency exceeding 90%. Hence, the review also presented an elaborate discussion of the photocatalytic process as one of the advanced techniques and highlighted some basic concepts to optimize the degradation efficiency of a photocatalyst. Finally, a brief recommendation for research prospects is also presented.

The development of platinum group metal-free (PGM-free) electrocatalysts derived from cheap and environmentally friendly biomasses for oxygen reduction reaction (ORR) is a topic of relevant interest, particularly from the point of view of sustainability. Fe-nitrogen-doped carbon materials (Fe-N-C) have attracted particular interest as alternative to Pt-based materials, due to the high activity and selectivity of Fe-Nx active sites, the high availability and good tolerance to poisoning. Recently, many studies focused on developing synthetic strategies, which could transform N-containing biomasses into N-doped carbons. In this paper chitosan was employed as a suitable N-containing biomass for preparing Fe-N-C catalyst in virtue of its high N content (7.1%) and unique chemical structure. Moreover, the major application of chitosan is based on its ability to strongly coordinate metal ions, a precondition for the formation of Fe-Nx active sites. The synthesis of Fe-N-C consists in a double step thermochemical conversion of a dried chitosan hydrogel. In acidic aqueous solution, the preparation of physical cross-linked hydrogel allows to obtain sophisticated organization, which assure an optimal mesoporosity before and after the pyrolysis. After the second thermal treatment at 900 °C, a highly graphitized material was obtained, which has been fully characterized in term of textural, morphological and chemical properties. RRDE technique was used for understanding the activity and the selectivity of the material versus the ORR in 0.5 M H2SO4 electrolyte. Special attention was put in the determination of the active site density according to nitrite electrochemical reduction measurements. It was clearly established that the catalytic activity expressed as half wave potential linearly scales with the number of Fe-Nx sites. It was also established that the addition of the iron precursor after the first pyrolysis step leads to an increased activity because of both an increased number of active sites and of a hierarchical structure, which improves the access to active sites. At the same time, the increased graphitization degree, and a reduced density of pyrrolic nitrogen groups are helpful to increase the selectivity toward the 4e- ORR pathway.

Solid particle cationic polyacrylamide (CPAM) is one of the most commonly used organic polymer flocculants in oilfield wastewater treatment, but there are some problems, such as slow dissolution rate, and easy to form a "fish-eye" in the process of diluting into aqueous solution. However, the current liquid CPAM products also have some problems, such as low effective content, poor storage stability, degradation in a short time and high preparation cost. In this paper, a secondary processing technology of solid particle CPAM was studied, and a CPAM suspension was successfully prepared. This suspension has an effective content of 50.00%, No separation in 7 days of storage at room temperature, no separation in 30 min of centrifugation at a speed of 2000 r/min, and diluted to a 0.40 % weak gel solution in just 16.00 min. For 1000 NTU of diatomite simulated wastewater, the optimal turbidity removal rate of the suspension was 99.50%, which was higher than the optimal turbidity removal rate of 98.40% for the inorganic flocculant polymeric aluminum chloride (PAC). For oil and gas field oily wastewater, the optimal turbidity removal rate of CPAM suspension was 35.60%, which was higher than the optimal turbidity removal rate of 28.40% for solid particle CPAM.

This study aims to determine the optimal configuration (position and operation duration) for wall mounted mechanical mixers based on the comparison of three-dimensional computational fluid dynamics (CFD) modelling results and physical data collected from the treatment plant. A three-dimensional model of anoxic zone 1, 2 and 3 of Northern Wastewater Treatment Plant (WWTP) located at Cairns Regional Council, Cairns, Queensland, Australia was developed and validated. The model was used to simulate the flow pattern of the WWTP and the simulation results are in good agreement with the physical data varying between 0% to 15% in key locations. The anoxic zones were subject to velocities less than the desired 0.3 metres per second however results for suspended solids concentration indicate that good mixing is being achieved. Results for suspended solids concentrations suggest that the anoxic zones are towards the upper limits recommended by literature for specific power dissipation. The duration for operation of mechanical mixers was investigated and identified that the duration could be reduced from 900 seconds down to 150 seconds. Alternative mixer positioning was also investigated and identified positioning which would increase the average flow velocity with decreased duration (150 seconds). The study identified that Council may achieve savings of $24,000 per year through optimisation of the mechanical mixers.

Clostridial infections in cattle are a significant concern for Brazilian livestock. These diseases are caused by various species of Clostridium, which are known for their ability to produce potent toxins. Botulism in cattle is a serious and often fatal condition caused by the ingestion of neurotoxins produced by C. botulinum. This bacterium thrives in decomposing organic matter, such as spoiled feed, carcasses, and contaminated water. Tetanus while less common, tetanus is a serious disease following contamination of wounds with Clostridium tetani spores. It results in muscle stiffness, spasms, and often death due to respiratory failure. Blackleg (C. chauvoei) is this disease primarily affects young cattle, leading to acute lameness, swelling, and high fever. Malignant edema (C. septicum and others) is characterized by rapid onset of swelling at wound sites, malignant edema can occur after injuries or surgical procedures. Enterotoxemia is triggered by the rapid growth of C. perfringens in the gut following excessive carbohydrate intake. This leads to toxin production that causing sudden death. In conclusion, clostridial bovine infections remain a persistent challenge for Brazilian cattle farmers. With continued focus on vaccination, good management practices, and research, the impact of these diseases can be minimized, safeguarding the livestock industry's economic viability.

Background: Leishmaniasis is a significant global public health issue that is caused by parasites from Leishmania genus. With limited treatment options and rising drug resistance, there is a pressing need for new therapeutic approaches. Molecular chaperones, particularly Hsp90, play a crucial role in parasite biology and are emerging as promising targets for drug development. Objective: This study evaluates the efficacy of 17-DMAG in treating BALB/c mice from cutane-ous leishmaniasis through in vitro and in vivo approaches. Materials and Methods: We assessed 17-DMAG cytotoxic effect on bone marrow-derived mac-rophages (BMMΦ) and its effects against L. braziliensis promastigotes and intracellular amastigotes. Additionally, we tested the compound's efficacy in BALB/c mice infected with L. braziliensis via intraperitoneal administration to evaluate the reduction of lesion size and de-crease of parasite load in the ears and lymph nodes of infected animals. Results: 17-DMAG showed selective toxicity [selective index=432) towards Leishmania amastigotes, causing minimal damage to host cells. The treatment significantly reduced lesion sizes in mice and results in parasite clearance from ears and lymph nodes. It also diminished in-flammatory responses and reduced the release of pro-inflammatory cytokines (IL-6, IFN-g, TNF) and the regulatory cytokine, IL-10, underscoring its dual leishmanicidal and anti-inflammatory properties. Conclusion: Our findings confirm the potential of 17-DMAG as a viable treatment for cutaneous leishmaniasis and support further research into its mechanisms and potential applications against other infectious diseases.

With the ongoing amendment of the EU legislation on the treatment of urban wastewater, stricter requirements for the removal of pollutants are expected, which calls for the need for innovative wastewater treatment technologies. Biological systems are still the first choice. The survey of typical bioreactors applied in wastewater treatment is presented. Wastewater treatment objective, bio-chemical environment and microbial growth are selected as a main criterion for classification of these bioreactors. Hydraulic and kinetic aspects are considered, advantages and drawbacks of these bioreactors regarding the selection of appropriate type of the reactor as well as regarding operation of reactors are mentioned. The aim of this paper is to provide operators and designers with a brief overview of selected traditional and advanced processes, reactors, and technologies for nutrient removal from municipal wastewater. Another goal is to discuss the possibilities and limitations to comply with more strict effluent standards. From the evaluation of the published papers, it follows that the currently applied traditional methods of nutrients removal have the potential to convey also with the expected stricter limits.

In this work, Density Functional Theory (DFT) calculations were employed to study the photocatalytic CO2 to CO reduction by a series of Pt(II) square planar complexes with general formula [Pt(5-R-dpb)Cl] (dpb = 1,3-di(2-pyridyl)benzene anion, R = H, N,N-dimethylaniline,T thiophene, diazaborinine). The CO2 to CO conversion process is thought to proceed via two main steps, namely the photocatalytic/reduction step and the main catalytic step. The simulated absorption spectra exhibit strong bands in the 200 – 400 nm UV-Vis region. The calculated excited state reduction potentials are in the range 0.32 — -0.36 V revealing that the reductive quenching of the T1 state of the complexes could be modulated with suitable changes of the N^C^N pincer ligands. The CO2 fixation and activation by the ‘real’ three coordinated Pt(II) catalyst/intermediate is predicted to be favorable with Pt-CO2 bond dissociation energies, D0 in the range -36.9—-10.3 kcal/mol. The nature of the Pt-CO2 bond is complex with covalent, hyperconjugative and H-bonding interactions prevailing the repulsive electrostatic interactions. The main catalytic cycle is estimated to be a favorable exergonic process.

Bacterial resistance to antibiotics is a growing global concern, threatening human and environ-mental health, particularly among urban populations. Wastewater treatment plants (WWTPs) are thought to be “hotspots” for antibiotic resistance dissemination. The conditions of WWTPs, in conjunction with the persistence of commonly used antibiotics, may favor the selection and trans-fer of resistance genes among bacterial populations. WWTPs provide an important ecological niche to examine the spread of antibiotic resistance. We used heterotrophic plate count methods to identify phenotypically resistant cultivable portions of these bacterial communities and charac-terized the composition of the culturable subset of these populations. Resistant taxa were more abundant in raw sewage and wastewater before the biological aeration treatment stage. While some antibiotic resistant bacteria (ARB) were detectable downstream of treated wastewater re-lease, these organisms are not enriched relative to effluent-free upstream water, indicating effi-cient removal during treatment. Combined culture-dependent and culture-independent analyses revealed a stark difference in community composition between culturable fractions and the envi-ronmental source material, irrespective of culturing conditions. Higher proportions of the envi-ronmental populations were recovered than predicted by the widely accepted 1% culturability paradigm. These results represent baseline abundance and compositional data for ARB commu-nities for reference in future studies addressing the dissemination of antibiotic resistance associ-ated with urban wastewater treatment ecosystems.

The construction of an anaerobic digester coupled with post-digestion low level aeration for agricultural wastewater treatment is described. The digester employs underwater speakers to accelerate the anaerobic digestion process while retaining solids to reduce the strength of the effluent. The digester effluent is sent to a holding tank and fed at a low flow rate to an aeration tank to effect partial nitrification of the wastewater. The outlet of this tank is sent to a settling tank to retain biomass that developed in the aeration tank and the effluent is sent to a small, constructed wetland to further reduce wastewater nitrogen and phosphorus. The wetland was planted with the broadleaf cattail, Typha latifolia, and hence to a retention basin. The system has reduced energy consumption due to both the use of underwater sonic treatment and low-level aeration that is not designed to achieve full nitrification/denitrification but rather to achieve a mixture of ammonium, nitrite, and nitrate that might foster the development of a consortium of organisms (i.e. nitrifiers, Anammox bacteria) that can remediate wastewater ammonium at low cost. Biogas is sent to an inground condenser where different treatments may be tested to remove carbon dioxide and hydrogen sulfide. The system is meant to serve as a complex where various technologies and practices can be evaluated to improve the treatment of agricultural wastewater.

The dye effluent is usually difficult to be degraded by conventional wastewater treatment in leather industry. In order to develop efficient and cost-effective treatment methods, we evaluate the effect of white-rot fungus immobilization for dye decolorisation in this paper. The Phanerochaete chrysosporium BKM-F-1767 was used for immobilization. This research found that the white-rot fungus immobilization had an obviously decolorisation effect in dye wastewater treatment, and plant carriers such as sorghum stalk and corn cob were helpful to the growth of Phanerochaete chrysosporium in white-rot fungus immobilization. Due to the stability and recyclability, the white-rot fungus co-immobilization was considered as the most suitable treatment for decolorisation of dye effluent which enjoyed the advantages of both adsorption immobilization and entrapment immobilization. Furthermore, the dye decolorisation evaluation was carried out to find the most suitable carrier for co-immobilization, and it found that sorghum stalk - calcium-alginate gel spherical particle (SS-CGPB) has better decolorisation effect than corn cobs - calcium-alginate gel spherical particle (CC-CGPB), and the dye decolorisation rate was 86.77%. After 5 cycles, the dye decolorisation rate was 85.87% which indicated the SS-CGPB preserved functional integrity successfully. By further analyzing the biodegradation process with white-rot fungus immobilization, the intermediate products were observed and the degradation pathway of acid golden yellow dye molecular was proposed. The results showed that the C-N single bonds attached to the central benzene in the dye molecule were attacked and destroyed in white-rot fungus co-immobilization treatment, thus the structure of dye molecule could be successfully degraded into small molecules which would be more easily treated by conventional treatment methods. Therefore, the white rot fungus co-immobilization might be appropriate for pre-treatment as an important biotechnology for the advanced treatment of dye effluent.

Water pollution in developing countries affects the public health of humans and the environment. It is therefore essential to develop environmentally friendly biopolymer, sustainable and low-cost membranes. Biopolymer nanofiber membranes are made by an electrospinning process of polylactic acid (PLLA) with additives. The main objective of this study is to manufacture biodegradable nanofiber membranes for use in filtering the suspended elements in wastewater at the level of drinkable or in agricultural fields. It is known that PLLA is brittle and therefore it is difficult to apply in industry. To solve this problem and enhance its flexibility. Flexible biopolymer polypropylene carbonate (PPC) and plasticizer are the addition in PLLA to reduce its glass transition and enhance its crystallization by adding Poly(3-hydroxy butyrate) PHB. In this work, 20 wt% of PPC was added to PLLA matrix to improve its elasticity and elongation at break. DSC shows that the addition of PPC, PHB, and TEC did affect the thermal properties like T_g, T_cc and T_m of the PLLA blends. The position of the T_g, T_cc, and T_m is shifting, the consequence the chain mobility is increased, therefore the crystallinity is enhanced. Electrospun fibers of PLLA/PPC/PHB/TEC were successfully manufactured. Tensile tester showed the increase in elongation at break of PLLA blend films, the elongation at break increases by 285 times. It observed with the increasing the elongation at break, a decrease in stress strength. After improving the mechanical properties with the higher elongation at break values, this blend is optimal for filtrations process.

Thermal plasma technique is becoming prominent in the treatment of variety of waste ranging from municipal solid waste, incinerator residue, hospital waste, electronics waste and industrial sludge. Application of the new treatment technology to petroleum sludge requires information on the nature and characteristics of the sludge that will be use to optimize the treatment system. In this investigation, petroleum sludge obtained from Petronas Melaka was characterized for its physical and chemical features. Proximate and ultimate analysis as well as determination of elemental composition were carried out. The sludge was found to contain high moisture (78.91%), low ash (5.06%), low volatiles (5.52%) and high fixed carbon (10.51%). The sludge has a TOC of 54.48% and HHV of 23.599MJ/kg. Despite the high moisture content, the higher heating value (HHV) is high when compared to literature values. The high value of HHV may be associated with the high fixed carbon, low ash content and high value of TOC. The apparent density of the sludge is slightly lower. Fourteen heavy metals are detected in significant quantities. Proper waste management that will safely dispose the sludge is required. The waste disposal technique should take into cognizant the possibility of leaching of heavy metals into ground water on one hand and the gasification of lighter ones on the other.

The beginning of industrialization human being has observed a variety of environmental troubles in the world. This industrialization has not only brought growth and affluence but ultimately troubled the ecosystem. One of the crashes is visible, in form of water contamination. Here the current study heavy metal contamination of water body has been discussed. Effluents from a great number of industries viz., tannery, textile, pigment & dyes, paint, wood processing, petroleum refining, electroplating, leather etc., have a major amount of heavy metals in their wastewater. The conventional technique of handling heavy metal pollution includes chemical oxidation, chemical precipitation, ion exchange, reverse osmosis, membrane separation, electrodialysis etc. These processes are expensive, energy intensive and frequently related with generation of poisonous by-product. Therefore, the adsorption has been examined as a cost-efficient technique of elimination of heavy metals from wastewater. In the current study different low-cost adsorbent has been a review as an abatement of heavy metal contamination from wastewater. These adsorbent comprise materials of natural origin like peat moss, zeolites, clay, and chitin are found to be an effective agent for removal of deadly heavy metals like Pb, Cd, Zn, Cu, Ni, Hg, Cr etc. Separately from these, a variety of agricultural wastes like rice husk, waste tea, neem bark, black gram; Turkish coffee, walnut shell etc. were also known as a powerful adsorbent for heavy metal removal. at the side of that low-cost industrial byproduct like fly ash, lignin, iron (III) hydroxide and red mud, coffee husks, Areca waste, tea factory waste, sugar beet pulp, battery industry waste, blast furnace sludge, waste slurry, sea nodule remains and grape stalk wastes have been discovered for their technical possibility to eliminate toxic heavy metals from impure water.

The efficiency and performance of Proton Exchange Membrane Fuel Cells (PEMFCs) are primarily influenced by ORR electrocatalysts. In recent years, atomically dispersed met-al-nitrogen-carbon (M-N-C) catalysts have gained significant attention due to their high active center density, high atomic utilization, and high activity. These catalysts are now considered the preferred alternative to traditional noble metal electrocatalysts. The unique properties of M-N-C catalysts are anticipated to enhance the energy conversion efficiency and lower the manufac-turing cost of the entire system, thereby facilitating the commercialization and widespread ap-plication of fuel cell technology. This article initially delves into the origin of performance and degradation mechanisms of Fe-N-C catalysts from both experimental and theoretical perspectives. Building on this foundation, the focus shifts to strategies aimed at enhancing the activity and durability of atomically dispersed Fe-N-C catalysts. These strategies encompass the use of bi-metallic atoms, atomic clusters, heteroatoms (B, S, and P), and morphology regulation to optimize catalytic active sites. The article concludes by detailing the current challenges and future pro-spects of atomically dispersed Fe-N-C catalysts.

The mechanistic pathway of TEMPO/I₂-mediated oxidative cyclization of N,N-diaryl amino alcohols 1 is investigated in this study. Based on our direct empirical experiments, three key intermediates (the aminium radical cation 3, the α-aminoalkyl radical 4, and the iminium 5), four kind reactive species (radical TEMPO, cationic TEMPO, TEMPO-I and iodo radical) and three kind pathways (1. SET/PCET mechanism, 2. HAT/1,6-H transfer mechanism, 3. Ionic mechanism) were assumed. Under the assumption, nine free energy diagrams are acquired through DFT calculation. From the comparison of the solution phase free energy, some possibility can be excluded and then the chosen plausible mechanisms are concretized with the more stable intermediate 7.

The stepwise hydrogenation of the C=C bond and C=O group of acrolein on Au₃ and Au₅ model systems is investigated using the density functional theory(DFT) PW91 functional. Our results show that the C=C hydrogenation is more favorable than that of C=O bond on Au₃ with the barriers of the rate-determining step being 0.35 and 0.62 eV respectively. On the other hand, the C=O reduction is preferred over the hydrogenation of the C=C bond on Au₅. The corresponding barriers of the rate-determining steps are 0.45 and 0.54 eV, respectively. This demonstrated that the second hydrogenation step controls the reaction on both Au₃ and Au₅ for C=O and C=C hydrogenation and the C=O hydrogenation on Au₅ is preferred over the hydrogenation of the C=C bond, which is helpful to address the reactivity of small size-selected supported gold clusters.

The primary objective of this study was to demonstrate the potential of digital image analysis as a tool to identify microplastic (MP) particles in surface waters and to facilitate their characterisation in terms of 2D and 3D morphology. Digital image analysis preceded by microscopic analysis was used for an exhaustive quantitative and qualitative evaluation of MPs isolated from the Vistula river. Using image processing procedures, 2D and 3D shape descriptors were determined. The Principal Components Analysis (PCA) was used to interpret the relationships between the parameters studied, characterising MP particle geometry, type and colour. This multivariate analysis of the data allowed 3 or 4 main factors to be extracted, explaining approximately 90% of the variation in the data characterising MP morphology. It was found that the first principal component for granules, flakes and films was largely represented by strongly correlated with 2D shape descriptors (area, perimeter, equivalent area diameter) and 3D shape descriptors (CSF, Compactness, Dimensionality). Considering the scraps, PC1 was represented by only five of the above descriptors, and the Compactness variable had the largest contribution to PC2. In addition, for granules, flakes and films, a relationship between 2D shape and the colour of their particles could be observed. For the most numerous MP group identified of multicoloured scraps, no such association was found. The results of our study can be used for further multivariate analysis regarding the presence of microplastic floating on the river surface, with a particular focus on particles of secondary origin. This is of key importance for optimising future efforts in conducting small-scale and multidimensional monitoring of and reducing plastics in the aquatic environment.

In this work the influence of the structure forming agent on the composition, morphology and oxygen reduction reaction (ORR) activity of Fe-N-C catalysts was investigated. As structure forming agent (SFA), dicyandiamide (DCDA) (nitrogen source) or oxalic acid (oxygen source) or mixtures thereof were used. For characterization, cyclic voltammetry and rotating disc electrode (RDE) experiments were performed in 0.1 M H2SO4. In addition to this, N2 sorption measurements and Raman spectroscopy were performed for the structural characterization. The role of metal, nitrogen and carbon sources within the synthesis of Fe-N-C catalysts has been pointed out before. Here, we show that the optimum in terms of ORR activity is achieved if both N- and O-containing SFAs are used in almost similar fractions. All catalysts display a redox couple, whereat its position depends on the fractions of SFAs. The SFA has also a strong impact on the morphology: Catalysts that were prepared with a larger fraction of N-containing SFA revealed a higher order in graphitization, indicated by bands in the 2nd order range of the Raman spectra. Nevertheless, the optimum in terms of ORR activity is obtained for the catalyst with highest D/G band ratio. Therefore, the results indicate that the presence of an additional oxygen-containing SFA is beneficial within the preparation.

Activated sludge process is a well known method to treat municipal and industrial waste water. In this complex process, the oxygen concentration in the reactors plays a critical role in the plant efficiency. This paper proposes the use of a Long Short-Term Memory (LSTM) network to identify an input-output model suitable for the design of an oxygen concentration controller. The model is identified from easy-accessible measures collected from a real plant. This dataset covers almost a month. The performances achieved with the proposed LSTM model are compared with the ones obtained with a standard AutoRegressive model with eXogenous input (ARX). Both models catch the oscillation and the overall behaviour (ARX ρ=0.833 , LSTM ρ=0.921), but, while the ARX model fails in reaching the correct amplitude (FIT=41.20%), the LSTM presents satisfactory performance (FIT=60.56%).

: Microplastics and nanoplastics (MNPs) are becoming an increasingly severe global problem due to their widespread distribution and complex impact on living organisms. Apart from their environmental impact, the effects of MNPs on living organisms have also continued to attract attention. The harmful impact of MNPs has been extensively documented in marine invertebrates and larger marine vertebrates like fish. However, the research on the toxicity of these particles on mammals is still limited, and their possible effects on humans are poorly understood. Considering that MNPs are commonly found in food or food packaging, humans are primarily exposed to them through ingestion. It would be valuable to investigate the potential harmful effects of these particles on gut health. This review focuses on recent research exploring the toxicological impacts of micro- and nanoplastics on the gut, as observed in human cell lines and mammalian models. Available data from various studies indicate that the accumulation of MNPs in mammalian models and human cells may result in adverse consequences, in terms of epithelial toxicity, immune toxicity, and disruption of gut microbiota. The paper also discusses the current research limitations and prospects in this field, aiming to provide a scientific basis and reference for further studies on the toxic mechanisms of micro- and nanoplastics.

In this paper, Fe-Cr-C-N-Al-Y wear-resistant surfacing alloy was prepared by open arc surfacing with self-shielded flux-cored wire. The wear properties of the surfacing alloy were analyzed by MLS-23 rubber wheel wet sand wear tester. The phase composition and microstructure of the surfacing alloy were analyzed by XRD, SEM, EBSD and TEM, and the strengthening mechanism and wear mechanism of the alloy were discussed. The results show that the microstructure of Fe-Cr-C-N-Al-Y surfacing alloy is composed of M + γ-Fe + M7C3 + AlN. When the content of nano-Y2O3 is 0.456wt. %, the formability of the surfacing alloy is the best and the wetting angle is the smallest, which is 50.8°, AlN and M7C3 precipitate the most, and the microstructure grain is the smallest. At this time, the hardness value of the surfacing alloy is up to 62.3 HRC, which is 11.8 % higher than that of the unmodified surfacing alloy. The minimum wear weight loss is 0.125 g, and the wear resistance is increased by 41.86 %. The wear mechanism of surfacing alloy is mainly plastic deformation mechanism, and the material removal process is micro cutting and furrow wear.

The requirement for developing tools capable of detecting and monitoring heavy metals (HMs) has recently taken on more significance due to worries about their toxic effect on human health and aquatic habitats. In this study, a simple electrochemical sensing carbon paste electrode (CPE) based on composite of Zinc/Iron layered double hydroxide (LDH) and polyaniline (PANI) was developed for the determination of lead ions in aquatic solutions. For this purpose, Zn-Fe LDH/PANI was prepared and characterized by Fourier transform infrared (FTIR), X ray diffraction (XRD), and scanning electron microscopy (SEM). Modified carbon electrode based Zn-Fe LDH/PANI was electrochemically characterized compared with unmodified electrode in FCN as a redox probe using cyclic voltammetry (CV). Thus, Zn-Fe LDH/PANI was utilized as sensing material for the electrochemical determination of lead ions using differential pulse voltammetry (DPV). Zn-Fe LDH/PANI/CPE show limits of detection (LOD) and quantification (LOQ) of 167.8 nM and 559.4 nM, respectively. Zn/Mg/Fe LDH was prepared using co-precipitation method and characterized by XRD, FTIR, SEM and BET, used for removal of Pb+2 ions. Removal process was investigated at different conditions as pH, metal ion concentrations, starting adsorbent dose at first and contact time. Zn/Mg/Fe LDH was evaluated as an effective adsorbent material for lead ions elimination in aquatic solutions, with capacity of adsorption 700 mg/g. The elimination of lead ions on Zn/Mg/Fe LDH fitted the pseudo first-order kinetics model and the isotherm was matched with Langmuir model. Studies revealed that the ideal removal conditions were pH = 5.0, an adsorbent mass of 0.05 g, and 20 ml of 50 ppm metal ion concentration at 60 min. The Zn-Fe LDH/PANI composite also showed potential anti-cancer properties against lung cancer cells (A549) while maintaining safety for normal lung fibroblast cells (WI-38). Collectively, advancements in electrochemical sensors offer promising solutions for lead ion detection, with wide-reaching applications in wastewater treatment and cytotoxicity assessment. These innovations have the potential to enhance environmental monitoring and public health safety.

Nutrient estimation in forest ecosystems through satellite images allows us to obtain accurate data, starting with data transformation from forest stands and the existing relationship with the spectral information of the image through modeling. The objective of the study was to quantify and validate the content of C, N, H in aboveground tree biomass in managed stands using spatial modeling and satellite images. This study was conducted during 2017-2018 in managed forest stands in San Juan Lachao, Oaxaca, Mexico. Fifteen 400 m2 experimental sites were selectively established, using a completely randomized experimental design of five silvicultural treatments with three replications. As part of data preprocessing, normality and homogeneity of variances assumptions were checked using the Shapiro-Wilk and Bartlett tests, respectively. From the pixels, data of the average of Normalized Difference Vegetation Index (NDVI) that surrounded the sampling sites were contrasted against the data obtained from forest inventory and the regression models to estimate C, N, H and biomass were generated. Models were validated by NDVI. With the models we estimated 0.95 t ha-1 biomass, which contains between 0.61 and 0.63 of C, 0.44-0.46 of N and 0.24 of H. The models generated had coefficients of determination (R2) of 0.85 to 0.87, which are significant parameters (p ≤ 0.0001). These results confirm that the use of Sentinel satellite images in the estimation of these elements in forest ecosystems based on the relationship between data inventory and the NDVI is highly reliable.

physicochemical methods was effective for the degradation of organics, but was highly hampered by the salt coexist in the complex wastewater matrix, resulting in low degradation dynamics. In this study, ZnO loaded carbon nitride (Zn-CNx) was synthesized and exhibited an excellent performance for 2,4-dichlorophenol (2,4-DCP) degradation (0.63 mg/L/min) in photcatalysis system. The doping of Zn into CNx contributed to the increased light absorption of the catalyst and the optimized electron transport pathways. The quenching experiment results proved that the superoxide radicals (·O2-) played a dominant role and hydroxyl radical (·OH) played a secondary role. Notably, the 2,4-DCP removal increased slightly with increasing salt content. As the initial pH increased from 3 to 11, the first-order degradation kinetic constants increased significantly, and the final pH was equilibrized in the range of 6.01-6.59. This study provided a high performance catalyst for photcatalysis and the mechanism for the effective degradation of 2,4-DCP under high salinity condition.

The presence of heavy metals in industrial effluents has recently become a source of concern for human health and the environment. Efficient removal of metal ions and wastewater treatment is essential for protecting public health and the environment. In this study, we present an eco-friendly, green synthesis of reactive and fully dispersed zerovalent iron nanoparticles (nZVI) in carbon nanofibers via an electrospinning technique. In this novel study, green tea (GT) was used as environmentally friendly, polyvinyl alcohol (PVA) was used for the stabilization and reduction of nZVI, and tetraethyl orthosilicate (TEOS) was added to provide flexibility and to increase the specific surface area of the nZVI based nanofibers. GT contains polyphenols, which act as reducing agents, converting iron ions into nZVI and the particles can then serve as the building blocks for the carbon nanofibers. TEOS can also contribute to the stability of the nZVI by coating their surfaces with a silica layer. This silica layer helps prevent the oxidation of the nZVI, thereby reducing their catalytic activity. The nZVI-based composite (∼ 400 nm) / carbonized (∼ 200 nm) nanofibrous mats were fully characterized by scanning electron microscopy. The average size of the nZVI embedded in the composite and carbonized nanofibers can range from 50 nm to 100 nm. The x-ray diffraction (XRD) analysis of nZVI-based carbon nanofibers showed that there is no crystallinity and a single-phase cubic structure. Both energy-dispersive X-ray spectroscopy (EDX) and Fourier transform infrared (FTIR) analysis also confirmed the formation of single-phase nZVI-based composite / carbonized nanofibers. The high intensity of the peaks in the FTIR spectrum indicates the formation of nZVI in the nanofibers structure. The electrospun nZVI-based carbon nanofibers have a higher surface area and better reactivity due to small particle size and large surface area-to-volume ratio. They can provide excellent water stability and dispersibility in water compared to bulk nZVI, which tend to agglomerate and settle quickly. Additionally, nanofiber morphology can enhance the mechanical strength and durability of the composite material. Due to low-cost synthesis and their high efficiency in removing pollutants, these nanofibers could be used as nano-filters for wastewater treatment.

This study develops into the application of a combined MFC unit with chemical coagulation for total treatment of inert contaminants in complex substrates. Microbial Fuel Cell (MFC) technology converts chemical energy in the form of organic matter, into bioelectricity in an environmentally friendly and effi-cient manner, reducing carbon emissions and increasing bioenergy production. An evaluation of a la-boratory scale chemical coagulation using an aluminum and poly-based coagulant on how effective it can remove bulk impurities such as particulate COD and turbidity to obtain the purest and most cost-effectively treated wastewater using a jar test is being conducted in this current study. This study aims to find the most effective treatment technologies for wastewater recovery in breweries in order to achieve zero liquid effluent discharge (ZLED). The preliminary results showed that adding a modest amount of poly and a 50 % alum alone treatment improved COD, color, and turbidity reduction. The turbidity removal efficiency achieved after chemical coagulation treatment was 90.50 % and 59.36 % COD removal, demonstrating the benefits of adopting an alum/poly based technique. To determine ZLED, this study clearly advised a combined treatment technique, specifically the MFC-flocculator unit for efficient organics and inorganics removal.

The world is struggling with the increasing rate at which water bodies are constantly polluted due to rapid modernization and industrialization. The different types of water contaminants include both anthropogenic and natural contaminants. Environmentalists are mainly concerned about heavy metals such as cadmium ions, as they are considered poisonous and carcinogenic even if they are present at a minimum concentration, and they are considered an immediate concern, according to the World Health Organization. Recently, many methods, such as solvent extraction, ion exchange, electrochemical precipitation, and reverse osmosis, have been developed to remove heavy metals from wastewater. These methods have been reported to be expensive and inefficient; hence, more cost-effective and eco-friendly alternative strategies are needed. Amidst these challenges, a ray of hope emerges in the form of biosorbents. These abundant, eco-friendly, and cost-efficient materials have shown promise as an alternative method for removing heavy metals from wastewater. They are equipped with functional groups that can effectively absorb metal ions onto their surfaces, offering a potential solution to our water contamination woes. This review is significant as it delves into the potential use of several biosorbents to decontaminate cadmium ions from wastewater. This review is significant as it delves into the potential use of several biosorbents to decontaminate cadmium ions from wastewater

Measurements of complex magnetic permeability, μ(f,H)=μ′(f,H)-iμ″(f,H) and dielectric permittivity ε(f,H)=ε′(f,H)-iε″(f,H), in the frequency range, f of (0.4-7) GHz, and polarizing field, H of (0–135) kA/m, were performed, for a kerosene-based ferrofluid with magnetite nanoparticles. Based on these measurements, the phenomenon of ferromagnetic resonance was highlighted and some microwave propagation parameters of the ferrofluid were determined: the attenuation constant, α(f,H), and the reflection coefficient, R(f,H), at the air-material interface. Knowing these parameters we proposed a theoretical model establishing for the first time a new equation that allows the calculation of the overall reflection coefficient, Rw(f,H), of a ferrofluid with thickness d, deposited on a totally reflective support, following multiple internal reflections of the electromagnetic wave in the material. The results show that by increasing both, H, and d, the parameter, Rw(f,H) presents a minimum that decreases from 0.90 (for d=2mm) to 0.64 (for d=10 mm), at frequency f=5 GHz, which indicates an increase in the absorption of the electromagnetic wave by the ferrofluid. The obtained results are useful in the study of some materials that could be used as electromagnetic absorbers in the microwave range, by the determination of the overall reflection coefficient, Rw(f,H), controlled both by the thickness, d , of the absorber and by the external applied field, H.

Materials based on platinum metals with very good catalytic activity were tested in the reduction of p–nitrophenol (pNP) to p–aminophenol (pAP). The majority of presented catalytic materials are based on the adsorption of p–nitrophenol on the surface of the catalyst simultaneously with molecular hydrogen, coming from sodium borohydride in an aqueous medium, which reduces it. In the present paper, a catalytic material based on osmium dispersed in n–decanol or n–dodecanol is presented, which also works as an emulsion membrane, for the absorption of p–nitrophenol and molecular hydrogen at the n–alcohol aqueous solution interface. The hydrogenation of p–nitrophenol is carried out in a reaction and separation column in which the acid receiving phase emulsion is dispersed in the osmium nanodispersion, in n–alcohols. This emulsion circulates from the base of the column to its upper part in co-current or counter-current with the source phase consisting of p–nitrophenol and sodium borohydride. Experiments show that the circulation of counter-current phases is superior to that in co-current, and the emulsion based on n–decanol is more efficient than the one based on n–dodecanol. The increase in the pH difference between the source and receiving phases leads to the increase in the conversion of p–nitrophenol to p–aminophenol. The efficiency of separation of the reaction product in the receiving phase is lower than the conversion at the same operating time. The apparent catalytic rate constant (kapp) of the new catalytic material based on the emulsion membrane with nanodispersion of osmium nanoparticles (0.1×10−3 for n–dodecanol and 0.9×10−3 for n-decanol) is lower by an order of magnitude compared to those based on adsorption on catalysts from platinum metal group. The advantage of the tested membrane catalytic material is that it extracts p–aminophenol in the acid receiving phase. The paper proposes a mechanism of the studied reduction system.

This study employed the Fully Modified Ordinary Least Squares (FMOLS) and the Error Correction Model (ECM) to investigate the long-run and short-run determinants of unemployment rate in Nigeria. To achieve this annual data on unemployment rate, inflation rate, interest rate, exchange rate and population growth from 1981 to 2016 was collected from Central Bank Statistical Bulletins and the World Bank website. The ADF test revealed that the macroeconomic variables are stationary at first difference while the Cointegration test revealed that the variables are cointegrated. Using unemployment rate as dependent variable, the FMOLS model revealed that exchange rate and population growth are positively significantly related to unemployment rate, interest rate and inflation rate were negatively related to unemployment rate but only interest rate was significant. The short run relationship revealed that the coefficient of the ecm(-1) is negative and statistically significant at 5% level indicating that the system corrects its previous period disequilibrium at the speed of 48.93% yearly. This study concludes that high exchange rate and population growth can lead to increase in unemployment rate in Nigeria while the government should develop the industrial sector and non-oil sector in order to generate employment and boost export in Nigeria.

The article presents comparative results from 5 categories of animals (4 samples originating from pigs, 2 from cows, 1 from chicken, 1 from ostriches, 1 from horses, samples quantified with A, B, C, D, E, F, G, H, I). These samples were collected from large, medium and small (family) farms. The results were validated by the biogas production generated by the respective samples, using the Automatic Methane Potential Test System (AMPTS II) bio-processor. The largest amounts of biogas (2,464.5 Nml, 2,262.0 Nml) were recorded for the samples from pig farms (Sample B and Sample D), whereas the lowest values were obtained in the case of Sample A (414.1 Nml) and Sample C (558.3 Nml). The heavy metals analyzed in the article are Zn, Cu, Fe, Mn, Ca, K, As. The results corroborate that the C/N ratio can also vary to values lower than 20-30, without affecting the biogas production process, and the heavy metal content must be known especially for the full management of the wastes. All final data presented in the article are based on repeated, triplicate experiments, with less as 2% deviation between data.

Climate change, increasing global food needs, and decreasing global resources brought a new era to human every-day live with a strong turn to circular economy and sustainability. Food packaging and preservation is an important global sector where enchanced research is carried out. New methods such as active packaging and chemical preservatives replacement are of major interest. Many researchers were published studies about active packaging films, replacement of chemical preservatives with natural originated extracts, and novel incorporation procedures. Sequentially to our and other scientists’ previous work, in this paper we present the results of the improvement which was achieved by incorporating the developed nanohybrid of natural-halloysite/carvacrol-extract, the pure natural carvacrol extract and the commonly used low-density-polyethylene. The well known corona-treatment procedure was employed to produced the optimum final film and the results shown that the low-density-polyethylene incorporated with natural-halloysite/carvacrol-extract nanohybrid and coated external with extra carvacrol extract exhibited aproximatelly 100% higher Young-Modulus values, slightly decreased ultimate strength by 20%, and almost stable elonation at break properties. The water-vapor and oxygen barrier increased by 40%. Finally, the antioxidant activity of the corrona-treated film increased by 28% compared to the similar but untreated product because of the lower release rate of the carvacrol.

Integrated Fixed Film Activated Sludge (IFAS) technology greatly enhances nitrogen removal effectiveness and treatment capacity in municipal wastewater treatment plants, addressing the issue of limited land availability. Hence, this method is appropriate for treating household wastewater from office buildings. The research was conducted at the wastewater treatment plant in an office building in Ho Chi Minh City, Vietnam. Experiments were conducted to ascertain the most favorable working conditions, including Hydraulic Retention Time (HRT), alkalinity dosage, and Dissolved Oxygen (DO). According to the study, the IFAS system had the highest nitrogen removal effectiveness when operated at a hydraulic retention time (HRT) of 7 hours, an alkalinity dose of 7.14 mgCaCO3/mgN-NH4+, and a dissolved oxygen (DO) value of 6 mg/L. The nitrification efficiency ranges from 89.2% to 98.8%. The nitrate concentration post-treatment is within the range of 27 – 45 mg/L, which is lower than the allowable discharge limit of 60 mg/L as per Vietnam's wastewater discharge requirements. The research findings have enhanced the efficiency of the office building management process, thereby promoting the sustainable growth of society.

Nanoscience is a rapidly growing science stream that has been one of the cost-effective and energy-efficient approaches with wide applications. Water pollution is a major issue that is increasing continuously due to anthropogenic activities and several organic and inorganic contaminants. To overcome this issue, nanoparticles (NPs) have been successfully used to treat water. These NPs possess many beneficial applications in many fields like agriculture, cosmetics, photoconductors, environmental biotechnology, glass and alloy production, solar cells, nanomedicine and drug deliveries, biosensors, food industries, etc. The properties comprising high surface area, greater chemical reactivity, and mechanical properties play a vital role in imparting such beneficiary properties. As a result, there has been an increasing demand for the synthesis of NPs. However, excess usage of NPs further creates toxic by-products. Therefore, scientists and researchers are now focussing on the biogenic synthesis of NPs. The biological routes of NP synthesis have been crucial because they are eco-friendly and environmentally safe. This chapter highlights the usage of different approaches and biogenic sources for the production of NPs. It also discusses the recent advancement in the use of biogenic NPs with respect to applications for wastewater treatment.

The European Union Green Deal aims at curbing planet-warming greenhouse gas emissions and introducing clean energy production. But to achieve energy efficiency, the opportunity cost of different energies must be assessed. In this article, we analyse two different systems for the treatment of wastewater that, at the same time, produce energy for its own operation. On the one hand, high-rate algal ponds system (HRAP) is considered; on the other hand, we study a conventional activated sludge system which uses photovoltaic power (AS+PV). This paper offers a viability analysis of both systems based on the capacity to satisfy their energetic consumption. In order to assess this viability, the probability of not achieving the energy consumption threshold at least one day is studied. The results point that the AS+PV system self-sufficiency is achieved using much lesser surfaces than those of HRAP system (for the former, less than 6.500 m2, for the latter 40.000 m2). However, the important AS capital cost makes still the HRAP system more economic, although storage provides a great advantage for using the AS+PV in locations where we have a lot of irradiance. This viability analysis, along with the opportunity cost analysis, will be used to assess these two projects devoted to the treatment of wastewater.

The only solution to avoid pollution due to sewage is to treat the effluent and reuse water and sludge at the wastewater production site. This makes it necessary to install treatment plants distributed along the sewer system to prevent the movement of effluents with the consequent losses to the aquifer. This new management is called decentralized wastewater treatment. To make this change possible, it is necessary to develop treatment plants that do not represent a health hazard for citizens, eliminating the nuisance caused by traditional plants. These plants need to be robust, operate autonomously, have reduced maintenance and exhaustive control of each process, where each cubic meter of effluent is perfectly controlled, avoiding losses to the aquifer or discharges that may occur due to deficiencies in their purification capacity; constantly producing water and sludge, which are directly reusable with all the health and environmental guarantees regardless of variations in inlet effluent or environmental conditions. This article presents a paradigmatic case of a decentralized solution with conditions of maximum complexity that has been solved efficiently, saving around 98% of the initial investment, completely avoiding wastewater discharges into the environment and reusing 100% of the treated water, in 14 years of operation.

Contamination by microplastics (MP) in aquatic ecosystems is largely due to the release of millions of these particles from treated effluents from Wastewater Treatment Plants (WWTP). Due to the lack of policies and regulations that establish criteria for the control and elimination of MP from WWTP effluents, this research evaluated the presence of MP for particle sizes of 38 and 150 µm in influents and effluents from three WWTP in the port of Acapulco, Mexico. Using optical microscopy and Fourier transform infrared spectroscopy (FTIR) techniques, the MP detected were polyethylene (PE), polypropylene (PP), polyethylene terephthalate (PET) and polyvinyl chloride (PVC). MP removal efficiencies of 82.5 to 98.7% (38 µm) and 86.8 to 97.5% (150µm) were obtained; the MP average daily emissions to the receiving bodies of these three WWTPs were in the ranges of 9.5 x 106 - 4.70 x 108 particles and the annual emissions in the range of 3.05 x 109 - 1.72 x 1011 particles. This work reveals the urgency of implementing regulatory policies to avoid the continuous emission of MP to aquatic ecosystems from WWTPs in Acapulco, Mexico.

The efficiency of microbial inactivation in water is highly dependent on the type of treatment technology used as well as the characteristics of the water to be treated. Wastewater from poultry slaughterhouses carries a significant number of microorganisms posing threat to humans and the environment in general. Therefore, the treatment of poultry slaughterhouse wastewater requires the use of appropriate purification systems with high removal efficiency for microbial agents. In this study, the performance of an integrated treatment plant with electrolysis, ultrafiltration, and ultraviolet radiation as the principal treatment units is investigated in terms of microbial inactivation from poultry slaughterhouse wastewater. In this case, Total microbial number, Total coliform bacteria, Thermo-tolerant coliform bacteria, Pathogenic flora, including Salmonella coliphages, Spores of sulfite-reducing clostridia, Pseudomonas aeruginosa, and Staphylococcus aureus Enterococcus were studied. About 63.95% to 99.83% of the microbes were removed by the EC treatment unit, as well as 99.86% to 100% removal efficiency was achieved after the combined treatment. However, the Pseudomonas aeruginosa was the only microbial agent detected in the final effluent after the combined treatment. The phenomenon suggests that an upgrade to the treatment plant may be required to achieve 100% removal assurance for Pseudomonas aeruginosa.

The efficiency of microbial inactivation in water is highly dependent on the type of treatment technology used as well as the characteristics of the water to be treated. Wastewater from poultry slaughterhouses carries a significant number of microorganisms posing threat to humans and the environment in general. Therefore, the treatment of poultry slaughterhouse wastewater requires the use of appropriate purification systems with high removal efficiency for microbial agents. In this study, the performance of an integrated treatment plant with electrolysis, ultrafiltration, and ultraviolet radiation as the principal treatment units is investigated in terms of microbial inactivation from poultry slaughterhouse wastewater. In this case, Total microbial number, Total coliform bacteria, Thermo-tolerant coliform bacteria, Pathogenic flora, including Salmonella coliphages, Spores of sulfite-reducing clostridia, Pseudomonas aeruginosa, and Staphylococcus aureus Enterococcus were studied. About 63.95% to 99.83% of the microbes were removed by the EC treatment unit, as well as 99.86% to 100% removal efficiency was achieved after the combined treatment. However, the Pseudomonas aeruginosa was the only microbial agent detected in the final effluent after the combined treatment. The phenomenon suggests that an upgrade to the treatment plant may be required to achieve 100% removal assurance for Pseudomonas aeruginosa.

The environmental policy is compelling industries to treat their wastewater to a level that can be released into the domestic sewer system or even for reuse. However, many industrial branches are lacking space for traditional wastewater plant. Hence, electrokinetics wastewater treatment is a viable alternative as it is fast and does not require large space. However, the electrokinetics wastewater treatment is still mostly tested in the laboratory. In the current study, a prototype of electrokinetics wastewater treatment industrial-size device has been designed, constructed and tested under real conditions. In this paper the device is described and the results obtained from the operation of the device are presented and discussed.

Sachet water (SW) is a major source of drinking water in most Nigerian homes, thus making it a possible conveyance medium for health risks due to contamination rather than for replenishment of the body. This study collected SW from three busy neighborhoods and investigated for the presence of indicator bacteria – Escherichia coli (E. coli), Total Coliform (TC), Total Heterophilic Bacteria (THB), and Staphylococcus – and some physio-chemical parameters – total dissolved solids (TDS), pH, electrical conductivity (EC), and salinity. Multi-variable and exploratory statistical methods were applied to the results to determine correlations between bacterial contamination levels and perceived brand reputation. Bacteriological test with raw SW samples appeared too numerous to count (TNC) and thus required serial dilutions. After seven dilutions, results obtained revealed that SW brands with good reputation had no TC and E. coli and was statistically significant with groupings of other SW brands (χ2 = 12.28; p < 0.05 and χ2 = 37.96; p < 0.05) respectively. Additionally, SW brands with poor reputation had mean values of TC (19.7X10^8 cfu/ml;14X10^8 cfu/ml1.15X10^8 cfu/ml) and E.coli (18.2X10^8 cfu/ml;38.7X10^8 cfu/ml,32.4X10^8 cfu/ml) exceeding threshold value of zero set by the World Health Organization (WHO). Only one sample from poor reputation brand tested positive for Staphylococcus and was not statistically significant (χ2 =5.2191; p = 0.074). Principal Component Analysis (PCA)/ Factor Analysis (FA) revealed that most of the SW had fecal contamination in an alarming magnitude. Therefore, this study suggests that periodic cleaning of distribution lines, location specific treatment, QC and QA measures should be taken to reduce water security risk for SW consumption in the region.

Background: Although antiretroviral therapy (ART) effectively halt disease progression in HIV infections, complete eradiation of the virus remains elusive. Additionally, challenges such as long-term ART toxicity, drug resistance, and the demanding regimen of daily and lifelong ad-herence required by ART highlight the imperative need for alternative therapeutic and preventa-tive approaches. In recent years, broadly neutralizing antibodies (bNAbs) have emerged as promising candidates, offering potential for therapeutic, preventative and possibly curative in-terventions against HIV infection. Objective: This review aims to provide a comprehensive overview of the current state of knowledge regarding the passive immunization of bNAbs in HIV-1 infected individuals. Main findings: Recent findings from clinical trials have highlighted the potential of bNAbs in treatment, prevention, and in the quest of an HIV-1 cure. While monotherapy with a single bNAb is insufficient in maintaining viral suppression and preventing viral escape, ultimately leading to viral rebound, combination therapy with potent, non-overlapping epitope-targeting bNAbs have demonstrated prolonged viral suppression and delayed time to rebound by effec-tively restricting the emergence of escape mutations, albeit largely in individuals with bNAb-sensitive strains. Additionally, passive immunization of bNAb have provided ‘proof-of-concept’ for antibody-mediated prevention against HIV-1 acquisition, although com-plete prevention was not obtained. Therefore, further research on the use of bNAbs in HIV-1 treatment and prevention remains imperative.

PURPOSE: To investigate the oxylipin profiles in aqueous humor of primary open angle glaucoma (POAG) patients. METHODS: Aqueous humor samples were collected from 17 POAG patients and 15 cataract subjects and subjected to the liquid chromatography-mass spectrometry (LC-MS) analysis to detect the oxylipins. The prediction potential of the differential abundant oxylipins was assessed by the receiver operating characteristic (ROC) curves. Pathway and correlation analyses on the oxylipins and clinical and biochemical parameters were also conducted. RESULTS: The LC-MS analysis detected a total of 76 oxylipins, of which 29 oxylipins reached the detection limit. The multivariate analysis identified 5 differential abundant oxylipins, 15-keto-prostaglandin F2 alpha (15-kPGF2α), Leukotriene B4 (LTB4), 12,13-Epoxyoctadecenoic acid (12,13-Epome), 15-Hydroxyeicosatetraenoic acid (15-HETE) and 11-Hydroxyeicosatetraenoic acid (11-HETE). The 5 oxylipins are enriched in the arachidonic acid metabolism and linoleic acid metabolism pathways. Pearson correlation analysis showed that 11-HETE was positively correlated with intraocular pressure and central corneal thickness and negatively with cup/disk ratio in the POAG patients. In addition, 15-kPGF2α was positively correlated with visual field defect, and LTB4 was negatively correlated with macular thickness.  CONCLUSIONS: This study revealed the oxylipin profile in the aqueous humor of POAG patients. Oxylipins involved in arachidonic acid metabolism pathway could play a role in POAG and anti-inflammatory therapies could be potential treatment strategies for POAG.

Background: Reliable HPV testing and genotyping are essential for quality assurance in HPV-based primary screening, disease management and for monitoring the impact of HPV vaccination. The clinical validation of HPV molecular diagnostic assays has significantly contributed to these objectives, however little emphasis has been placed in assuring sample quality. This study aims to assess the accuracy of sample cellularity assessment using C-C Motif Chemokine Receptor 5 (CCR5) gene target as a marker of sample adequacy in molecular diagnostics. Methods: Jurkat cell line samples were counted both using Thoma cell-counting chamber and Fluorescent-Activated Cell Sorting (FACS). Jurkat cell line samples at three different concentrations were subsequently evaluated using the OncoPredict HPV Quality Control (QC) real-time PCR assay, employing CCR5 for molecular cellularity quantification. Results: Cellularity values obtained were comparable across the 3 different methods for all dilutions of the cell line tested. Conclusions: The results obtained from this study show that CCR5 represents a promising molecular marker for the accurate quantification of sample cellularity, confirming its use as a reliable sample adequacy control, thus reducing the risk of “false negative” results.

NMR spin relaxation times have been an instrumental tool in deciphering the local en-vironment of ionic species, the various interactions they engender and the effect of these interactions on their dynamics in conducting media. Of particular importance has been their application in studying the wide range of electrolytes for energy storage, on which this chapter is based. Here we highlight some of the research carried out on electrolytes in recent years using NMR relaxometry techniques. Specifically, studies on liquid electro-lytes, such as ionic liquids and organic solvent; on semi-solid-state electrolytes, such as ionogels and polymer gels, and solid electrolytes such as glasses, glass ceramics and polymers. Although this chapter focuses on a small selection of materials, we believe they demonstrate the breadth of application and the invaluable nature of NMR relaxometry.

Obesity is associated with serious comorbidities and economic implications. Bariatric surgery, most commonly Roux-en-Y gastric bypass and sleeve gastrectomy, are effective options for weight loss and improvement of obesity-related comorbidities. With the growing obesity epidemic, there has been a concomitant rise in bariatric surgeries, particularly in sleeve gastrectomy, which has been the most widely performed bariatric surgery since 2013. Gastroesophageal reflux disease (GERD) is highly prevalent in obese individuals, can significantly impact quality of life and may lead to serious complications. Obesity and GERD both improve with weight loss. However, as the incidence of sleeve gastrectomy rises, recent data has revealed a risk of exacerbation of pre-existing GERD or the development of de novo GERD following sleeve gastrectomy. We performed a detailed review of GERD post-sleeve gastrectomy, including its overall incidence, pathophysiology and current treatment paradigms.

The beginning of 2020 has seen the emergence of coronavirus outbreak caused by a novel virus called SARS-CoV-2. The sudden explosion and uncontrolled worldwide spread of COVID-19 show the limitations of existing healthcare systems to timely handle public health emergencies. In such contexts, innovative technologies such as blockchain and Artificial Intelligence (AI) have emerged as promising solutions for fighting coronavirus epidemic. On the one hand, blockchain can combat pandemics by enabling early detection of outbreaks, protecting user privacy, and ensuring reliable medical supply chain during the outbreak tracking. On the other hand, AI provides intelligent solutions for identifying symptoms caused by coronavirus for treatments and supporting drug manufacturing. Motivated by these, in this paper we present an extensive survey on the use of blockchain and AI for combating coronavirus (COVID-19) epidemics based on the rapidly emerging literature. First, we introduce a new conceptual architecture which integrates blockchain and AI specific for COVID-19 fighting. Particularly, we highlight the key solutions that blockchain and AI can provide to combat the COVID-19 outbreak. Then, we survey the latest research efforts on the use of blockchain and AI for COVID-19 fighting in a wide range of applications. The newly emerging projects and use cases enabled by these technologies to deal with coronavirus pandemic are also presented. Finally, we point out challenges and future directions that motivate more research efforts to deal with future coronavirus-like epidemics.

The conversion of caatinga vegetation areas into pastures in the Brazilian semiarid region has depleted soil fertility due to degradation. The natural regeneration of the caatinga has been the alternative adopted to restore soil fertility. However, the real effectiveness of this practice in re-covering organic carbon (SOC) and nutrient stocks is unknown. This work evaluated the effect of natural regeneration of the caatinga vegetation on the restoration of levels and stocks of SOC, N, and P as a strategy to maintain the sustainability of the environment. We collected soil samples every 5 cm, up to 20 cm deep, in areas of degraded pasture, caatinga in regeneration (10 years), and regenerated caatinga (35 years) to evaluate the levels and stocks of SOC, N, and P. The depth sig-nificantly affects the levels and stocks of SOC, N, and P. Stocks and levels of SOC, N, and P were higher in regenerated caatinga > regenerating caatinga > degraded pasture. The regenerated caatinga increased SOC, N, and P stocks by 115%, 110%, and 117%, respectively, compared to the degraded pasture. Although 35 years of regeneration of the caatinga has improved soil fertility, the levels and stocks of SOC, N, and P remain low.

The main inhibitory neurotransmitter in the mammalian brain is 4-aminobutyric acid (GABA). Phthalimide acts as a sodium channel antagonist, one of the finest targets for treating epilepsy is the sodium channel and JNK kinase activity is inhibited to treat epilepsy. a novel compound with multiple targets of action for the treatment of epilepsy also anti-oxidant activity has been designed. The compounds are designed in two series aldehydes and aniline. Docking of all the designed compounds has been done with the suitable protein GABA-AT, sodium channel, JNK protein, and anti-oxidant from protein bank. QSAR was done for constructing many linear regression models. In combination with the developed Docking and QSAR outcomes, ADMET has been performed for the active compounds. The result shows that 11 of the compounds have excellent binding energy in docking with all the receptors and also have good QSAR results and follow the ADMET. The structural understanding of human GABA-AT inhibition was obtained from molecular dynamics simulation studies for compound no. 11 at 5 nanoseconds. Synthesis and pharmacological activity also suggest that the designed compound no.11 be considered the best Novel Compound.

This study assessed the periodic fluctuations among microbial biomass Carbon (C), Nitrogen (N) and Phosphorus (P), and the consequences of variations in altitude and abiotic factors on the soil microbial biomass (C, N and P) in a temperate mixed-oak pine forest of Central Himalaya. This research was directed at three forest stands along an altitudinal gradient. Samples were collected in triplicates, seasonally from each selected site and microbial C, N and P were determined through the fumigation extraction method. Microbial biomass C, N and P decreased significantly (P<0.01, correlation coefficient -0.985, -0.963, -0.948, respectively) with increasing altitude, while the rainy season showed the highest values, and winter season revealed the least values. Microbial biomass C, N and P showed positive correlation with silt particles, water holding capacity, bulk density, porosity, soil moisture, organic C, total N and P, and negative correlations with sand particles and soil pH. The microbial biomass C showed strong associations with soil microbial N (r=0.80, P<0.01) and P (r=0.89, P<0.01) contents, while the soil microbial biomass N and P also showed strong positive correlation (r=0.92, P< 0.01). Soil microbial biomass was greatly influenced by the altitude and abiotic variables whereas, weakly by temporal variation. The microbial C: N ratio indicated that fertility of soil is influenced by the species assemblage. Our findings suggest that high microbial biomass and low C: N ratio during rainy season could be considered as a strategy to conserve nutrients by temperate mixed-oak pine forest ecosystem.

Polymeric drag reducers have been developed over many years due to the great number of practical applications. In all of them, the molecular stability is an essential requirement. Usually, polymers break down under turbulent flows, which causes a decrease in their efficiency as drag reducers. Besides that, some specific applications, in agro and biomedical fields, impose a specific requirement that must be fulfilled, which is the use of non-toxic materials. A suitable stable material that is elected to accomplish this necessity is the mucilage of aloe vera, which is a bio-polymer that can be used as an alternative to the synthetic ones. Here, we investigate the role played by the aging of aloe vera on its capacity to reduce drag. The results obtained by ¹H nuclear magnetic resonance indicate that the compositions of young and mature leaves of aloe vera are different and such a difference plays an important role on their efficiency as drag reducers. Tests were performed to analyse the drag reduction in a rotating apparatus and in a pipeline system and the efficiencies of leaves of different ages were compared to their composition. The main conclusion of these experiments is that the young mucilage samples, which are richer in complex polysaccharides and exhibit lower acid contents, are more efficient drag reducers.

In addition to being a source of freshener, coffee has an enormous possibility to be developed as a source of antioxidants for functional beverages. However, efforts to increase the value added of coffee as a health functional drink are still hindered by the presence of high level of caffeine, which is thought to have adverse effects on health, especially for coffee lovers who are vulnerable to caffeine. This study aims to optimise the steaming duration to produce low caffeine coffee while maintaining the sensory attributes and antioxidant compounds contained in it. Indonesian Arabica (Leksana variety) green coffee beans were steamed with multi-level steaming durations (0, 20, 40, 60 and 80 min) followed by roasting (medium-dark roast degree), grinding, and brewing (espresso method). The results indicate that caffeine content in the coffee was inversely proportional to the steaming duration. The lowest caffeine content was obtained from the treatment of 80 min steaming with a decrease of caffeine level up to 28.73%. However, the longer process of steaming caused a significant decrease in polyphenol content and antioxidant activity. The hedonic test shows that the steaming treatment of coffee can increase preferences of panellists. There were two driving attributes that influence the overall liking of coffee, namely: bitterness and aftertaste. Coffee obtained from the treatment of 60 min steaming was most preferred by panellists. The results of APLSR biplot mapping show that there was a big change in almost all attributes in the coffee samples after 40 min steaming.

Micropollutants belongs to various groups of chemicals. One of the most diverse and large group of them are pharmaceuticals. The presence of pharmaceutical residues in wastewater poses a significant challenge to water quality and environmental health. This paper provides an overview of recent advancements in the removal of pharmaceuticals from water, focusing on various treatment processes and their effectiveness in eliminating micropollutants. Through a review of literature, including studies on ozonation, UV irradiation, sulphate radical-based tech-nologies, and photocatalytic processes, insights into degradation mechanisms and optimal con-ditions for their removal are synthesized. Additionally, with new legislation mandating the monitoring of selected micropollutants and the implementation of quaternary treatment in wastewater treatment plants, the paper discusses prospects for future research and recommen-dations for effective pharmaceuticals removal. Key actions include conducting comprehensive laboratory and pilot trials, implementing quaternary treatment of wastewaters, continuously monitoring of water quality, investing in research and development, and promoting collabora-tion and knowledge sharing among stakeholders. By embracing these strategies, we can work towards safeguarding water resources and protecting public health from the adverse effects of pharmaceutical contamination.

This study aimed to assess the response of 3D printed PLA scaffolds biomimetically coated with apatite on human primary osteoblast spheroids and evaluate the biological response to its association with Bone Morphogenetic Protein 2 (rhBMP-2) in rat calvaria. PLA scaffolds were produced via 3D printing, soaked in simulated body fluid (SBF) solution, and characterized by physical-chemical, morphological, and mechanical properties. The in vitro biological response was assessed with human primary osteoblast (HOb) spheroids. The in vivo analysis was conducted through the implantation of 3D printed PLA scaffolds either alone, covered by apatite (PLA-CaP) or PLA-CaP loaded with rhBMP-2 (PLA-CaP+rhBMP-2) on critical-sized defects (8 mm) of rat calvaria. Increased cell adhesion and in vitro release of growth factors (PDGF, bFGF, VEGF) was observed for PLA-CaP scaffolds when pre-treated with FBS. PLA-CaP+BMP2 presented higher values of newly formed bone (NFB) than other groups at all experimental periods (p&lt;0.05), attaining 44.85% of NFB after 6 months. These findings indicate that functionalization of PLA scaffolds with biomimetic apatite can improve its biological properties in the presence of complex biological media. Its association with BMP2 may enhance bone repair, suggesting this strategy as a promising candidate for bone tissue engineering.

This study investigated the adaptability of Dunaliella salina to different salinity levels, with emphasis on growth, pigment concentration, and desalination potential. It was found that among the 21 salinity levels, salinity 75 produced consistently favorable results in cell count (13.08 x 10³ ± 1.41 x 10³ cells/mL), dry biomass (2.46 ± 0.06 g/L), pigment content (chlorophyll a = 97.5 ± 0.1 µg/L, chlorophyll b = 123.6 ± 0.3 µg/L), and desalination (9.32 ± 0.47 reduction). Therefore, salinity 75 was selected for the final trial (scale-up), which revealed unanticipatedly high cell counts (58.96 x 10³ ± 535.22 cells/mL), with dry biomass weight being statistically different (higher) than the expected (4.21 ± 0.02 g/L) (p<0.0001), most likely due to high cell count and energy reserve storage for high salinity adaption in the form of bio-compounds. Pigment growth continued (chlorophyll a = 95.4 ± 2.2 µg/L, chlorophyll b = 128.1 ± 5.1 µg/L), indicating pigment production under salt stress. Notably, desalination did not occur in this stage, possibly due to the necessity for a bigger initial inoculate, prolonged exposure or bioaccumulation becoming the prevailing mechanism over desalination. Nevertheless, the trial highlights D. salina's strong adaptation to various salinity levels. This suggests a promising future in halophyte research, particularly in understanding the mechanisms that prevent salt accumulation in cells and how to overcome this barrier. Additionally, these results suggest that microalgae could be a viable resource in saline-rich environments unsuitable for conventional agriculture, promoting industrial adaptation to adverse conditions.

This work shows the potential of a new way of co-treatment of domestic wastewater (DWW) and a liquid stream coming from the thermal hydrolysis of the organic fraction of municipal solid waste (OFMSW) mediated by a mixed culture of purple phototrophic bacteria (PPB) capable of assimilating carbon and nutrients from the medium. The biological system is an open single-step process operated under microaerophilic conditions at an oxidative reduction potential (ORP) &lt; 0 mV with a photoperiod of 12/24 h and fed during the light Stage only, so the results can be extrapolated to outdoors open ponds operation by monitoring the ORP. The effluent mostly complies with the discharge values of the Spanish legislation in COD and P values (&lt;125mg/L &lt;2 mg/L), respectively, and punctually on values in N (&lt;15mg/L). Applying an HRT of 3 d and a ratio of 100:7 (COD:N), the presence of PPB in the mixed culture surpassed 50% of 16S rRNA gene copies, removing 78% of COD, 53% of N and 66% of P. Furthermore, increasing the HRT to 5 d, removal efficiencies of 83% of COD, 65% of N and 91% of P were achieved. In addition, the reactors were further operated in a membrane bioreactor, thus separating the HRT from the SRT to increase the specific loading rate. Very satisfactory removal efficiencies were achieved by applying HRT and SRT of 2.3 and 3 d, respectively: 84% of COD, 49% of N and 93% of P despite low presence of PPB due to more oxidative conditions, which anyway step-by-step re-colonized the mixed culture until reaching &gt;20% of 16S rRNA gene copies after 49 d of operation. These results open the door to scale up the process in open photobioreactors capable of treating urban wastewater and municipal solid waste in a single stage and under microaerophilic conditions by controlling the ORP of the system. This novel urban biorefinery allows reducing treatment costs of two urban wastes and embed them in the circular bioeconomy through water recycling and valorizing PPB biomass as a source of carbon, nitrogen and phosphorus.

The purpose of this study is nutrient resources recovery by achieving the optimal chemical oxygen demand (COD) and carbon to nitrogen ratio (C/N) in co-composting wastewater treatment plant sludge with Municipal Solid Wastes (MSW). In this effort, the co-composting has been conducted in form of a case study in the northern region of Iran. In this research, 192 tests were carried out on four series of samples examined in terms of waste to sludge ratio, different aeration period, the percent of porous materials and the moisture content. This study was carried out at a temperature of 50 °C for a 15 day period by application of the in-vessel system and shows that the best ratio for waste to sludge is 2:1, while the 8 hour period is the best aeration period. The porous material which can be added to the composting process is limited to 15% in weight. In other words, any more or less amount of this material will adversely impact the process. Moreover, this research suggests that the sludge dewatering is not required in such processes. In Addition, the efficiency of both COD and C/N reductions equals to about 40%.

The vegetation in constructed wetlands (CWs) plays an important role in wastewater treatment. Popularly, the common emergent plants in CWs have been vegetation of natural wetlands. However, there are ornamental flowering plants that have some physiological characteristics similar to the plants of natural wetlands that can stimulate the removal of pollutants in wastewater treatments; such importance in CWs is described here. A literature survey of 87 CWs from 21 countries showed that the four most commonly used flowering ornamental vegetation genera were Canna, Iris, Heliconia and Zantedeschia. In terms of geographical location, Canna spp. is commonly found in Asia, Zantedeschia spp. is frequent in Mexico (a country in North America), Iris is most commonly used in Asia, Europe and North America, and species of the Heliconia genus are commonly used in Asia and parts of the Americas (Mexico, Central and South America). This review also compares the use of ornamental plants versus natural wetland plants and systems without plants for removing pollutants (COD, BOD, nitrogen and phosphorous compounds). The removal efficiency was similar between flowering ornamental and natural wetland plants. However, pollutant removal was better when using ornamental plants than in unplanted CWs. The use of ornamental flowering plants in CWs is an excellent option, and efforts should be made to increase the adoption of these system types and use them in domiciliary, rural and urban areas.

Microbial electrochemical technologies (MET) rely on the presence of the metabolic activity of electroactive bacteria for the use of solid-state electrodes for oxidizing different kind of compound, that could lead to the synthesis of chemicals, bioremediation of polluted matrices, the treatment of contaminants of interest, as well as the recovery of energy. Keeping in mind those possibilities, since the beginning of the present century, there has been a growing interest in the use of electrochemical technologies for wastewater treatment, and if possible with simultaneous power generation. In the last years, there has been a growing interest to explore the possibility of merging MET with constructed wetlands, to offer a new option of intensified wetland system that could keep a high performance with a lower footprint. Based on that interest, this paper explains the general principles of MET, and the different known extracellular electron transfer mechanisms ruling the interaction between electroactive bacteria and potential solid-state electron acceptors. Also, the adoption of those principles for the development of MET set-ups for simultaneous wastewater treatment and power generation, and the challenges that the technology face. Ultimately, the most recent developments in set-ups that merges MET with constructed wetlands are presented and discussed.

Carbapenemase-producing Enterobacter spp. Serratia marcescens, Citrobacter freundii, Providencia spp. and Morganella morganii (CP-ESCPM) are increasingly identified as causative agents of nosocomial infections but are still not under systematic genomic surveillance. In this study, using a combination of whole genome sequencing and conjugation experiments, we sought to elucidate the genomic characteristics and transferability of resistance genes in clinical CP-ESCPM isolates from Bulgaria. Among the 36 sequenced isolates, NDM-1 (12/36), VIM-4 (11/36), VIM-86 (8/36) and OXA-48 (7/36) carbapenemases were identified; two isolates carried both NDM-1 and VIM-86. The majority of carbapenemase genes were found on self-conjugative plasmids. IncL plasmids were responsible for the spread of OXA-48 among E. hormaechei, C. freundii and S. marcescens. IncM2 plasmids were generally associated with the spread of NDM-1 in C. freundii and S. marcescens, and also of VIM-4 in C. freundii. IncC plasmids were involved in the spread of the recently described VIM-86 in P. stuartii isolates. IncC plasmids carrying blaNDM-1 and blaVIM-86 have been observed too. blaNDM-1 was also detected on IncX3 in S. marcescens and on IncT plasmid in M. morganii. The significant resistance transfer rates highlight the role of the ESCPM group as a reservoir of resistance determinants and stress the need for strengthening the infection control measures.

A hydrothermal pretreatment of the microalga Nannochloropsis gaditana at mild temperatures has been studied in order to reduce N and O content in the biocrude obtained by hydrothermal liquefaction (HTL). The work is focused on the evaluation of temperature, reactor loading and time (factors) to maximize the yield of the pretreated biomass and the heteroatom contents transferred from the microalga biomass to the aqueous phase (responses). The study followed the factorial design and response surface methodology. An equation for every response has been obtained, which leads to the accurate calculation of the operating conditions required to obtain a given value of these responses. Temperature and time are critical factors with a negative effect on the pretreated biomass yield, but a positive one on the N and O recovery in the aqueous phase. The slurry concentration has to be low to increase heteroatom recovery and high to maximize the pretreated microalga yields

The study shows that the volumes and surfaces of the $n$-simplices, $n$-orthoplices, $n$-cubes, and $n$-balls are holomorphic functions of $n$, which makes those objects omnidimensional. Furthermore, the volume of an $n$-simplex is shown to be a bivalued function of $n$, and thus the surfaces of $n$-simplices and $n$-orthoplices are also bivalued functions of $n$. Applications of these formulas to the omnidimensional polytopes inscribed in and circumscribed about $n$-balls reveal previously unknown properties of these geometric objects in negative dimensions. In particular, for $0 < n < 1$, the volumes of the omnidimensional polytopes are larger than those of circumscribing $n$-balls, while their volumes and surfaces are smaller than the volumes of inscribed $n$-balls. Reflection relations around $n = 0$ for volumes and surfaces of these polytopes inscribed in and circumscribed about $n$-balls are disclosed. Specific products and quotients of volumes and surfaces of the omnidimensional polytopes and $n$-balls are shown to be independent of the gamma function.

Ribosomally synthesized and post-translationally modified peptides (RiPPs) are a structurally diverse group of natural products. They feature a wide range of intriguing posttranslational modifications as exemplified by the biarylitides. These are a family of cyclic tripeptides found in Planomonospora, carrying a biaryl-linkage between two aromatic amino acids. Recent genomic analyses revealed the minimal biosynthetic prerequisite of biarylitide biosynthesis consisting of only one ribosomally synthesized pentapeptide precursor as substrate and a modifying cytochrome P450 dependent enzyme. In silico analyses revealed that the minimal biarylitide RiPP clusters are widespread among natural product producers across phylogenetic borders including myxobacteria. We report here the genome-guided discovery of the first myxobacterial biarylitide MeYLH termed Myxarylin from Pyxidicoccus fallax An d48. Myxarylin was found to be an N-methylated tripeptide surprisingly exhibiting a C–N biaryl crosslink. In contrast to Myxarylin, previously isolated biarylitides are N-acetylated tripeptides featuring a C–C biaryl crosslink. Furthermore, the formation of Myxarylin was confirmed by heterologous expression of the identified biosynthetic genes in Myxococcus xanthus DK1622. These findings expand the structural and biosynthetic scope of biarylitide type RiPPs and emphasize the distinct biochemistry found in the myxobacterial realm.

(1) Background: Grapes and their associated by-products (as grape pomace, GP) stand out for their polyphenol content, which makes them a source of bioactive compounds with antioxidant capacity. The aim of this research was to determine if the inclusion of 50 g/kg of GP in the diet of hens could enrich egg with antioxidants and to study its effect on internal and external egg quality parameters. (2) Methods: A trial was conducted with two genetic lines of hens, which were fed either a control diet or a diet containing 50 g/kg of GP. Performance, internal and external egg quality, and egg yolk content of vitamins E and A, and gallic acid were determined; (3) Results: In eggs laid by hens fed GP diet, Haugh units and yolk colour score were enhanced, and eggshell became thinner, but without affecting the breaking strength. No dietary effect was observed on vitamin contents in yolk. Higher gallic acid content was observed in yolk of eggs laid by hens fed the GP diet, suggesting that some dietary phenolic compounds could be transferred to the eggs. Hen genetics influenced egg weight, albumen Haugh units, shell thickness and α- and γ-tocopherol concentration in yolks; (4) Conclusions: Dietary inclusion of GP improved the internal quality of eggs, enriching yolks with a phenolic compound, but reduced shell thickness.

Amphiphilic block copolymers of N-vinyl pyrrolidone (NVP) and various vinyl esters (VEs), PNVP-b-PVEs, namely vinyl butyrate (VBu), vinyl decanoate (VDc) and vinyl stearate (VSt) were synthesized by RAFT polymerization techniques. The sequential addition of monomers methodology was employed starting from the polymerization of NVP followed by the polymerization of the VEs monomer. The reaction was conducted at 80oC in dioxane solutions using AIBN as initiator and O-ethyl S-(phthalimidylmethyl) xanthate as the CTA. The block copolymers were characterized by Size Exclusion Chromatography (SEC) and NMR spectroscopy. The thermal transitions of the copolymers were studied by Differential Scanning Calorimetry (DSC), whereas their thermal stability via Thermogravimetric Analysis (TGA) and Differential Thermogravimetry (DTG).

In the case of a Cu-Mo-W polymetallic ore, the wastewater from the scheelite cleaning flowsheet contains large amounts of residual flocculants and metal ions, and the separation of chalcopyrite and molybdenite require a large number of environmentally harmful depressants. Therefore, it is necessary to find new methods to reduce the environmental and cost pressures of wastewater treatment and the use of depressants. In this work, the flotation wastewater from scheelite cleaning flowsheet for the separation of chalcopyrite and molybdenite by selective surface passivation was investigated for the first time. Flotations of single minerals and artificially mixed minerals with or without immersion pretreatment in the presence and absence of aeration were performed. The results showed that pulp pH had no effect on the flotation of either mineral, and a molybdenite recovery of 93.22% with chalcopyrite recovery of 10.77% was achieved under the conditions of 10 days of immersion pretreatment with aeration, 350 mg/L of kerosene, and 100 mg/L of MIBC. By combining the electrochemical cyclic voltammetry analysis and characterization by XRD and SEM, the selective surface passivation mechanism of chalcopyrite was discussed, which could be due to the coverage of the insoluble oxidation products, especially jarosite. This work has simultaneously achieved the depressant-free flotation separation of molybdenite and chalcopyrite and the reuse of scheelite flotation wastewater, which is of great significance for environmental protection and cost saving.

To achieve n-type doping in diamond, extensive investigations employing first principles have been conducted on various models of phosphorus doping and boron-phosphorus co-doping. The primary focus of this study is to comprehensively analyze the formation energy, band structure, density of states, and ionization energy of these structures. It is observed that within a diamond structure solely composed of phosphorus atoms, the formation energy of an individual carbon atom is excessively high. However, the substitution of two carbon atoms leads to the conversion of diamond into a p-type semiconductor. Upon examining the P-B co-doping structure, it is revealed that the doped impurities exhibit a tendency to form more stable cluster configurations. As the separation between the freely doped atoms and the cluster impurity structure increases, the overall stability of the structure diminishes, consequently resulting in an elevation of the ionization energy. Analysis of the electronic density of states demonstrates that the electron orbit of the B atom makes negligible contributions to the impurity levels during P-B doping.

Background/Aim: Stool gluten immunogenic peptides (GIP) determination is now considered a valuable tool for detecting dietary lapses in treated celiac disease (CeD) patients. Our study aims to explore the diagnostic performance of a qualitative lateral flow immunoassay point-of-care test (LFIA/PoCT) compared with a qualitative enzyme-linked immunosorbent assay (ELISA) for detection of stool GIP. Methods: The study is a post hoc analysis of stool samples collected in the real-life conditions from a cohort of gluten-free diet-treated CeD patients. Stool GIP was measured in µg/g of stool using an ELISA kit (iVYLISA GIP S®, Biomedal SL). For the qualitative evaluation of stool GIP, a LFIA/PoCT test (GlutenDetect®; Biomedal S.L) was employed, which reported results as positive or negative. The LFIA/PoCT performance was evaluated against ELISA, considered as the gold standard. GIP concentrations

The recognition of a place as a World Heritage Site (WHS) by UNESCO is fundamental to preserve its historical and artistic inheritance and, at the same time, to encourage visits to that area. The purpose of this article is to contribute to the study of the relationship between WHS and cultural tourism, with a marked sustainable character, through the presentation of the results of research conducted in the city of Cordoba (Spain) and which analyses the sociodemographic profile of the tourists, the variables that influence their level of satisfaction and of their loyalty and the classification of the travelers through different variables. The principal results of the research show the significant educational level of the surveyed tourists, as well as the high level of satisfaction with the visit, the high number of countries of origin and the outstanding motivation for knowing the city’s heritage roots.

Degnala is one of the main mycotoxicoses that affects buffaloes, and the fungus Fusarium spp. is the main causative agent. This disease is strongly related to the supply of rice straw to buffaloes and is considered endemic to regions where this crop is cultivated. Cases of the disease are concentrated in the winter, when conditions favour fungal growth in inadequately stored rice straw. Degnala is characterized by necrosis and gangrene of the extremities, including the tail, lower limbs, ears, tongue, muzzle and teats. The pelvic limbs are more affected than the thoracic limbs. A tortuous appearance of the tail is very common, and cracks or corneal loss of the hooves may occur, with exposure of the blades and even the bones. There is no diagnostic method for identifying the disease in animals other than the clinical and epidemiological criteria associated with fungal culture of rice straw samples. There is no treatment that neutralizes the effects of the toxins, and the treatment currently used is a palliative and supportive method consisting of pentasulfate solution, anti-Degnala liquid, 2% nitroglycerin ointment and broad-spectrum antibiotics for secondary infections. In addition, the management of drying straw and proper storage are essential for controlling this disease.