The conformity assessment of products or a measured value with the given standards is carried out based on the global risk of producers and consumers calculation. A product may conform to specifications but be falsely rejected as non-conforming. This is about the producer's risk. If a product doesn't meet the requirements but is falsely accepted as conforming, that poses a risk to the consumer. The conventional approach to risk assessment, which yields only a single numerical value for the global risk of producers and consumers, is naturally extended, and utilized for assessing risk in measurement models with linear regression. The outcomes of the two-dimensional extension, along a moderate scale, are the parabolas with an opening upwards. Risk surfaces were obtained through three-dimensional extension over the area limited by the moderate scale and guard band axes. Four models with different ranges of tolerance intervals were used to test this innovative method of risk assessment in linear regression. The corresponding standard measurement uncertainties are determined by applying a simplified measurement model with the use of comprehensive data on the measurement performance and by determining measurement uncertainty derived from consideration of the functional relationship obtained by linear regression analysis. Models that utilize information from linear regression analysis to determine measurement uncertainty are biased towards risks at the edges of the moderate scale. Testing the model's performances with metrics related to the confusion matrix, such as the F1 score, further substantiated this assertion. The diagnostic odds ratio has been proven to be extremely effective in identifying the curve along the guard band axis, along which the global risks of producers and consumers are at their lowest.

Functional partially linear regression model, contains a functional linear part and a non-parametric part, in which testing the linear relationship between the response and the functional predictor is of fundamental importance. When functional data cannot be approximated with a few principal components, based on a pseudo estimate for the unknown non-parametric component, we develop a U-statistic of order-two in this paper. Under some regularity conditions, we use the martingale central limit theorem to prove that the proposed test statistic is asymptotically normal. The finite sample performance with simulation studies and real data application are assessed to verify the proposed test procedure.

We prove an analog of the removable singularity theorem for bounded harmonic functions on stratified sets. The harmonic functions are understood in the sense of the soft Laplacian. The result can become one of the main technical components for extending the well-known Poincaré–Perron’s method of proving the solvability of the Dirichlet problem for the soft Laplacian.

In this paper, we present a relapse based demonstrating way to deal with investigate various arrangement MTC information. A commonplace use of this displaying approach incorporates three stages: first, define a model that approximates the connection between quality articulation and trial factors, with boundaries consolidated to address the exploration premium; second, utilize least-squares and assessing condition methods to gauge boundaries and their relating standard blunders; third, register test insights, P-qualities and NFD as proportions of factual criticalness. The benefits of this methodology are as per the following. To begin with, it tends to the exploration interest in a particular, precise way, and maximally uses all the information and other important data. Second, it represents both orderly and irregular varieties related with the information, and the consequences of such examination give not just quality explicit data applicable to the exploration objective, yet additionally its dependability, in this way helping agents to settle on better choices for subsequent investigations. Third, this methodology is truly adaptable, and can undoubtedly be stretched out to different sorts of MTC considers or other microarray explores by detailing various models dependent on the test plan of the investigations.

In the field of 2-D image processing and computer vision, accurately detecting and segmenting objects in scenarios where they overlap or are obscured remains a challenge. This difficulty is worse in the analysis of shoeprints used in forensic investigations because they are embedded in noisy environments such as the ground and can be indistinct. Traditional Convolutional Neural Networks (CNNs), despite their success in various image analysis tasks, struggle with accurately delineating overlapping objects due to the complexity of segmenting intertwined textures and boundaries against a background of noise. This study introduces employs the YOLO (You Only Look Once) model enhanced by edge detection and image segmentation techniques to improve the detection of overlapping shoeprints. By focusing on the critical boundary information between shoeprint textures and the ground, our method demonstrates improvements in sensitivity and precision, achieving confidence levels above 85% for minimally overlapped images and maintaining above 70% for extensively overlapped instances. Heatmaps of convolution layers were generated to show how the network converges towards successful detection using these enhancements. This research may provide a potential methodology for addressing the broader challenge of detecting multiple overlapping objects against noisy backgrounds.

Ultrasound (US) scans of the inferior vena cava (IVC) provide useful information on the volume status of a patient. However, their investigation is user-dependent and prone to measurement errors. An important technical problem is the objective difficulty in studying a very compliant blood vessel like IVC, which makes large respirophasic movements and shows a complicated three dimensional geometry. Using bi-dimensional (2D) B-mode views either in long or short axis has improved the characterization of IVC dynamics compared to a measurement along a single direction (M-mode). However, specific movements of the IVC can challenge also the information provided by these 2D sections. Thus, these two orthogonal views, provided by an US system in X-plane, are here integrated by an innovative method. It is tested on simulated videos of the IVC performing complicated movements, that are compensated by the new method, overcoming the biased measurements provided by 2D scans. The method is then applied on example experimental data.

We present an open-source Star Tracker (ST) for Attitude Determination. Our implementation makes use of open source software of common usage in astronomy running on a Raspberry Pi 2 platform. The developed platform is open and available for parties interested in further development. Evaluation of the system showed that the ST is suitable for Cubesats of 2U or larger. The ST platform is capable of solving the Lost-In-Space (LIS) problem. Currently, the average accuracy reached of the algorithm is close to 5 seconds of arc with an average processing time of 75 seconds. However, a average accuracy of about 3 minutes of arc can be reached with 35 seconds in average processing time. We also describe the evaluation procedure, the found conclusions of this procedure, in particular the section of the algorithm where most of the processing time is spent and other possible source of errors not included in this study.

With the use of linear regression modeling, this study sought to forecast and analyze rainfall patterns in Ethiopia. The dataset included historical rainfall data as well as pertinent independent variables. The R-squared score and mean squared error (MSE) were used to assess the effectiveness of the linear regression model. The results showed that the model's ability to forecast and analyze rainfall patterns was not very good. Only around 5.3% of the variance in rainfall could be explained by the chosen independent variables, according to the R-squared score of 0.053. This low number indicated that there was little correlation between the selected variables and rainfall, and that a sizable percentage of the variation in the dependent variable was not captured by the model. The model's accuracy in forecasting rainfall was shown to be quite low by the MSE error, with significant squared discrepancies between the expected and actual amounts. These results support the notion that the linear regression model as it is now designed is not appropriate for studying or forecasting Ethiopia's rainfall patterns. Alternative modeling approaches, the inclusion of other pertinent factors, and the assurance of the availability of high-quality data that faithfully captures the intricate dynamics of rainfall in the area all require more investigation.

This study investigates the suitability of the timestamp approach algorithm for predicting blood pressure (BP) using wearable and comfortable devices, showcasing its accuracy even with low-frequency sampled signals. Developed within the SINTEC European project, the algorithm utilizes Electrocardiogram (ECG) and Photoplethysmogram (PPG) sensors, demonstrating promising results in both laboratory and hospital settings. The research emphasizes the algorithm’s potential to transform continuous and non-invasive BP monitoring through wearable technology, offering frequent measurements with minimal discomfort. While the study shows promise, further exploration is needed, focusing on optimizing machine learning coefficients for long-term monitoring applications and addressing potential changes over time. Technological improvements, including the implementation of edge computing algorithms, hold the key to enhancing BP accuracy, denoising techniques, and integrating alarm systems for future wearable solutions. This study emphasizes the adaptability of the algorithm for diverse healthcare environments, paving the way for broader applications in convenient and reliable BP monitoring.

In this project, we use a statistical multiple regression to study the impact of eight various predictors (relative compactness, surface area, wall area, roof area, overall height, orientation, glazing area, glazing area distribution) to estimate the cooling load energy efficiency of residential buildings. We try to analyze and visualize the effect of each predictor with each of the response variable using different classical statistical analysis tools used in describing linear models, in such a way so that we can find out the most strongly related predictor variables. Before starting all of this, we use the idea of model selection by stepwise regression technique and compare the AIC of these models and identified a better model between all of them. Then, we compare a classical linear regression approach by simulations on 768 diverse residential buildings show that we can predict CL with low mean absolute error. By using ANOVA we determine variation in the different residuals. Also, we use non constant variance test to verify it. Furthermore, we check leverage and influence points as well as outliers as well as determined cook distance for influential points. By taking box cox transformation and weights, we also introduce WLS technique to fit the model for better results and did all type of important analysis to understand the energy efficiency. Finally, we show 5-fold cross validation to verify our model.

Although data acquisition is a very usual technique, there are several aspects not always considered, as synchronization of acquired measures and evaluation of the errors that derive from this fact. The paper hereby aims to point this thing out, by mathematical determination of the necessary correction and implementing the software meant to evaluate the performances of the acquisition system. As an example, a three-phased acquisition system has been developed in order to monitor the currents and voltages on the three phases. Also other measures have been calculated, such as power and phase. The components on each phase don’t have to be fully identified because a whole system calibration can be made in the first stage. Calibration consists in finding the weighting coefficients for each quantity. The implemented solution for three-phased measures data acquisition starts from the hypothesis of a sampling frequency that respects Shannon theorem. The distance between two samples is small enough to consider a linear evolution between two moments for the same measure. Errors that affect the above mentioned, due to the different moments of time when samples are acquired, are analyzed and brought to the minimum value.

Background: In the functional data analysis (FDA), the hybrid or mixed data are scalar and functional datasets. The semi-functional partial linear regression model (SFPLR) is one of the first semiparametric models for the scalar response with hybrid covariates. Various extensions of this model are explored and summarized. Methods: Two first research articles, including “semi-functional partial linear regression model”, and “Partial functional linear regression” have more than 300 citations in Google Scholar. Finally, only 106 articles remained according to the inclusion and exclusion criteria such as 1) including the published articles in the ISI journals and excluding 2) non-English and 3) preprints, slides, and conference papers. We use the PRISMA standard for systematic review. Results: The articles are categorized into the following main topics: estimation procedures, confidence regions, time series, and panel data, Bayesian, spatial, robust, testing, quantile regression, varying Coefficient Models, Variable Selection, Single-index model, Measurement error, Multiple Functions, Missing values, Rank Method and Others. There are different applications and datasets such as the Tecator dataset, air quality, electricity consumption, and Neuroimaging, among others. Conclusions: SFPLR is one of the most famous regression modeling methods for hybrid data that has a lot of extensions among other models.

This research introduces a hybrid feature extraction approach that combines Linear Discriminant Analysis (LDA) and Multilayer Perceptron (MLP) methods to address the challenges of reducing feature vector dimensionality and accurately classifying smartphone-based human activities. Moreover, to refine activity classification accuracy, Support Vector Machine (SVM) optimization with Stochastic Gradient Descent (SGD) is employed. LDA, a statistical tool, is leveraged to derive a new feature space for data projection, enhancing class separation and test feature label prediction. The proposed approach, named LMSS, was evaluated using the UCI-HAR dataset and compared with state-of-the-art models. The results demonstrate that the proposed approach outperformed the best-performing method over this dataset. It achieved an accuracy rate of 99.52%, precision of 99.55%, recall of 99.53%, and an F1-score of 99.54%, highlighting the effectiveness of the proposed method in accurately classifying the data.

Kinetic parameters of SO2 adsorption on unburned carbons from lignite fly ash and activated carbons based on hard coal dust were determined. The model studies were performed using the linear and non-linear regression method for the following models: pseudo first and second-order, intraparticle diffusion, and chemisorption on a heterogeneous surface. The quality of the fitting of a given model to empirical data was assessed based on: R2, R, Δq, SSE, ARE, χ2, HYBRID, MPSD, EABS, and SNE. It was clearly shown that it is the linear regression that more accurately reflects the behaviour of the adsorption system, which is consistent with the first-order kinetic reaction – for activated carbons (SO2+Ar) or chemisorption on a heterogeneous surface – for unburned carbons (SO2+Ar and SO2+Ar+H2O(g)+O2) and activated carbons (SO2+Ar+H2O(g)+O2). Importantly, usually, each of the approaches (linear/non-linear) indicated a different mechanism of the studied phenomenon. A certain universality of the χ2 and HYBRID functions has been proved, the minimization of which repeatedly led to the lowest SNE values for the indicated models. Fitting data by any of the non-linear equations based on the R or R2 functions only, cannot be treated as evidence/prerequisite of the existence of a given adsorption mechanism.

This paper details the comprehensive activities conducted in a laboratory setting to assess the Structural Health Monitoring (SHM) of prefabricated building envelopes. Aimed at enhancing the structural evaluation of buildings, the focus of this research lies in employing nondestructive sensors for SHM with the objective to advance in the understanding and assessment of facade conditions. The paper outlines the methodologies employed, starting with a modal analysis to define the structural vibration's modal frequency. Subsequently, tests were defined and executed to validate building envelope compliance in case of stress typical of high-rise building. Throughout these tests, continuous monitoring of the façade was conducted using both conventional (accelerometers, extensimeter washers) and non-conventional sensors (Fiber Optic Sensing) The gathered data underwent thorough processing and analysis to provide an overall perspective on the structure's behavior during the stress test. The investigation aimed to identify whether specific physical phenomena correlate with distinct signals and to evaluate if continuous façade monitoring over the building's lifespan aids in preventing potential structural damage. Moreover, two modal analyses were conducted to compare final data and frequencies with earlier data, enabling the detection of any structural alterations. The results from compliance testing and structural analysis yielded noteworthy insights contributing to the evolving field of structural health monitoring, offering valuable findings that advance our ability to proactively manage and maintain the integrity of building structures.

We present a differentially private extension of the block coordinate descent based on objective perturbation. The algorithm iteratively performs linear regression in a federated setting on vertically partitioned data. In addition to a privacy guarantee, the algorithm also offers a utility guarantee; a tolerance parameter indicates how much the differentially private regression may deviate from an analysis without differential privacy. The algorithm’s performance is compared with the standard block coordinate descent algorithm and the trade-off between utility and privacy is studied. The performance is studied using both artificial test data and the forest fires data set. We find that the algorithm is fast and able to generate practical predictions with single-digit privacy budgets, albeit with some accuracy loss.

Let BT4l denotes a subclass of bounded turning functions connected with a four-leaf-type domain. The goal of the study is to probe into coefficients of |b6|, |b7|, |b8|, the bounds of the logarithmic coefficients and the third-order determinants of H3,1, H3,2, H3,3 for functions in this class.

Every finite simple group P can be generated by two of its elements. Pairs of generators forP are available in the Atlas of finite group representations as (not necessarily minimal) permutation representations P . It is unusual but significant to recognize that a P is a Grothendieck’s dessin d’enfant D and that a wealth of standard graphs and finite geometries G - such as near polygons and their generalizations - are stabilized by a D. In our paper, tripods P − D − G of rank larger than two,corresponding to simple groups, are organized into classes, e.g. symplectic, unitary, sporadic, etc (as in the Atlas). An exhaustive search and characterization of non-trivial point-line configurationsdefined from small index representations of simple groups is performed, with the goal to recognize their quantum physical significance. All the defined geometries G's have a contextuality parameterclose to its maximal value 1.

Byers Peninsula (62°34’-62°40’S-60°54’61°13’W), 60 km2 in size, is considered one of the largest ice-free areas in Antarctica. Since 2006, the Spanish Polar Program has taken part in a large number of environmental studies involving effects of climate changes, limnology and microbiology, live cycles, but not albedo. Surface albedo is one of the key physical parameters in the surface energy budget of polar regions. Most of Antarctica is covered by ice sheets; only about 0.44% of the area is permanently ice-free. However, in maritime Antarctica, the ice-free areas, corresponding to small islands, peninsulas, and coastal beaches, account for about 3% of the territory. To incorporate the contribution of these areas into global albedo models, it is necessary to relate the soil properties of the ice-free areas to the surface albedo response. Also, mapping soil properties and albedo have and special interest in these ice-free areas. Image classification using machine learning methods trained with georeferenced soil data could be useful for mapping soil properties and albedo in multispectral optical satellite images. A shallow neural network implemented using the Keras Python module was used to define and train models of soil properties using 15 explanatory variables corresponding to bands and spectral indices of a Sentinel image and a population of 49 soil samples taken from the top 5 centimeters of the soil profile. The soil samples were analyzed in the laboratory and a spectral library in the Vis-Nir range (350-2500 nm) was created. The albedo of the samples was integrated from the ADS spectra. At the same time, a linear regression model of albedo using the soil properties as explanatory variables was performed. The R2 fit of this new model was about 0.82 and the error of estimation was 4.1. The model was extended to the entire Byers Peninsula using the ML soil property models as explanatory variables. The RMSE of the extended models increased up to 8.2. We think that the main cause of this increase (2.6 points) is related to the error propagation, phenomenon due to the use of models as explanatory variables. However, another important part of the error increase could be due, among other reasons, to the use of an image that, although corrected, is not completely free of clouds.

We develop an action principle for producing a single fluid, two-constituent system with dissipation in general relativity. The two constituents in the model are particles and entropy. The particle flux creation rate is taken to be zero, while the entropy creation rate is non-zero. Building on previous work, it is demonstrated that a new term (the proper time derivative of the matter space ``metric'') is required in the Lagrangian in order to produce terms typically associated with bulk and shear viscosity. Equations of motion, entropy creation rate, and energy-momentum-stress tensor are derived. Using an Onsager approach of identifying thermodynamic ``forces'' and ``fluxes'' a model is produced which delivers the same entropy creation rate as the standard, relativistic Navier-Stokes equations. This result is then contrasted with a model generated in the spirit of the action principle, which takes as its starting point a specific Lagrangian and then produces the equations of motion, entropy creation rate, and energy-momentum-stress tensor. Unlike the equations derived from Onsager reasoning, where the analogs of the bulk and shear viscosity coefficients are prescribed ``externally'', we find that the form of the coefficients in the second example are a direct result of the specified Lagrangian. Furthermore, the coefficients are shown to satisfy evolution equations along the fluid worldline; also a product of the specific Lagrangian.

Soccer is the leading cause of all sports-related ocular injuries in Europe and Israel and leads to blindness at a disproportionately high rate, especially among children (Thompson et al., 2019). With soccer being the most popular sport in the world, it is surprising the only solution to ocular injuries are sports glasses which can cause direct damage to the eye and impair peripheral vision by 15%, calling for an alternative (Smith & Jones, 2020). This work, based on an imported facial model, focuses on both the qualitative and quantitative aspects of building a personalized, low-cost (through optimizing material needed), superior apparatus to conventional sports glasses. The quantitative side examines a modified and model-validated (through a SRS of thirty unique extrapolated points) multivariate linear regression equation, based on horizontal and vertical rotation angles (n=60) trained with residual and computer simulation data, that can accurately extrapolate and quantify ocular impact from all horizontal and vertical rotation angles and a modified Hertzian Contact Stress Equation to determine the thickness of the apparatus using the elasticity modulus, impact force, and geometrical facial and soccer-ball features. The qualitative side examines where firstly, ocular impact is most prevalent, and secondly, where most impact is seen from rotating the ball horizontally and vertically through analysis of Pearson’s Correlation Coefficient at the supraorbital, medial canthus, infraorbital, and lateral canthus regions from both regression equations as well as a cost-benefit analysis for comparison with conventional sports glasses. The findings discovered in this work lay the groundwork for future research to build a customized low-cost ocular injury prevention device which can simultaneously ensure complete ocular safety while enhancing athletic performance for over 250,000,000 players (Johnson & Garcia, 2022).

Ridge regression is one of the most popular shrinkage estimation methods for linear models. Ridge regression effectively estimates regression coefficients in the presence of high-dimensional regressors. Recently, a generalized ridge estimator was suggested by generalizing the uniform shrinkage of ridge regression to the non-uniform shrinkage, which was shown to perform well under sparse and high-dimensional linear models. In this paper, we introduce our newly developed R package “g.ridge” (the first version published on 2023-12-07 at https://cran.r-project.org/package=g.ridge) that implements both the ridge estimator and generalized ridge estimators. The package equips with the generalized cross-validation for automatic estimation of shrinkage parameters. The package also includes a convenient tool for generating a design matrix. By simulations, we test the performance of the R package under sparse and high-dimensional settings with the normal and skew-normal error distributions. From the simulation results, we conclude that the generalized ridge estimator is superior to the benchmark ridge estimator based on “glmnet”, and hence, it can be the most recommended estimator under sparse and high-dimensional models. We demonstrate the package using the intracerebral hemorrhage data.

Arc sensors have been used in seam tracking and widely studied since the 80s; commercial arc sensing products for T and V shaped grooves have been developed. However, it is difficult to use these arc sensors in narrow gap welding because arc stability and sensing accuracy are not satisfactory. Pulse gas melting arc welding (P-GMAW) has been successfully applied in narrow gap welding and all position welding processes, so it is worthwhile to research P-GMAW arc sensing technology. In this paper, we derived a linear mathematical P-GMAW model for arc sensing, and the assumptions for the model are verified through experiments and finite element methods. Finally, the linear characteristics of the mathematical model were investigated. In torch height changing experiments, uphill experiments, and groove angle changing experiments the P-GMAW arc signals all satisfied the linear rules. In addition, the faster the welding speed, the higher the arc signal sensitivities; the smaller the groove angle, the greater the arc sensitivities. The arc signal variation rate needs to be modified according to the welding power, groove angles, and swing or rotate speed.

Having in view the sustainable management of forests, the intensity of silvotechnical interventions is analyzed and documented for young mixed beech stands regenerated naturally by taking into account the allometric relationships between some representative dendrometric elements, respectively, between the height of the trees and the corresponding diameter of their crowns. For this purpose, a functional dependence is established between the height and diameter of the tree crown from young beech stands within which silvotechnical interventions were or were not applied. A mathematical model based on cubic spline regression was developed, also taking into account the determination of the average diameter of the crown for each stand. This average diameter can be used to determine the optimal number of trees per surface unit (ha) at a given time. The research was carried out in three young beech stands, through statistical-mathematical inventories, on sample plots of 300 square meters with a tolerance of 10% and a coverage probability of 90%. The optimal diameter of the crown was obtained by applying the spline regression model, and the most appropriate functional dependence was established, resulting in a linear regression law with a positive slope.

The importance of XAI is undeniable in the current scenario and thus it's importance in considerable. Unfortunately, there are a couple of scenarios where the current XAI models fail. Additionally, attackers seek vulnerabilities in these models. This review paper is intended to cover some of the important scenarios where the existing XAI models may fail and some progresses made which shows their vulnerabilities and how to secure them.

Spatial interpolation of meteorological data can have immense implications on risk management and climate change planning. Kriging with external drift (KED) is a spatial interpolation variant that uses auxiliary information in the estimation of target variable at unobserved locations. However, the traditional KED methods with linear trend functions may not be able to capture the complex and non-linear interdependence between target and auxiliary variables, which can lead to an inaccurate estimation. In this work, a novel KED method using least squares support vector regression (LSSVR) is proposed. This machine learning algorithm is employed to construct trend functions regardless of the type of variable interrelations being considered. To evaluate the efficiency of the proposed method (KED with LSSVR) relative to the traditional method (KED with a linear trend function), a systematic simulation study for estimating the monthly means temperature and pressure in Thailand in 2017 was conducted. The KED with LSSVR is shown to have superior performance over the KED with the linear trend function.

A self-protective metal/ liquid microcapsule composite plating coating has been prepared in our previous research. The release speed of liquid core material from microcapsules is crucial for the coating surface properties. The aim of this paper is to study the permeability rule of liquid microcapsules within composite coatings. According to permeability experimental data’s linear characteristics, multiple linear regression is firstly used to set up permeability model of liquid microcapsules. The results show that a reliable mathematical model about membrane porosity, viscosity of core material and membrane thickness is established under ambient temperature and moisture. Meanwhile, the predictive capacity and reliability of this model are analyzed carefully.

Byers Peninsula is considered one of the largest ice-free areas in Maritime Antarctica. Since 2006, the Spanish Polar Program has taken part in a large number of environmental studies involving effects of climate changes in lives cycles, limnology and microbiology. Soils from maritime Antarctica are generally weakly developed and have chemical, physical and morphological characteristics strongly influenced by the parent material. However, biological activity during the short Antarctic summer promotes intense transference of nutrients and organic matter in areas occupied by different species of birds and marine mammals. To mapping and monitoring those areas with high biological occupation, could be very useful to have models of edaphic properties prepared from satellite images. In this approach, Deep Learning and Linear Regression models of soil properties and spectral indexes as explicative variables were performed. We training models of soil properties closely related to biological activity such as Dissolved Organic Carbon (DOC) and the iron fraction associated with organic matter (Fe). We tested the best approach to model the spatial distribution of DOC, Fe and pH by training models of Linear Regression and Deep Learning over Sentinel2 and WorldView2 images. The most robust models were used to track possible areas with ornithogenic soils as well as areas of the Byers Peninsula that could support the highest biological development.

This work discusses the feasibility of multiple linear regression in predicting water/CO₂ relative permeability using training and testing datasets from two nearby wells, separately, of the Lower Cretaceous Lakota Sandstone, Jurassic Hulett Sandstone, and Pennsylvanian Minnelusa Formation at the Dry Fork Station site. The outcome is promising as the predicted and measured relative permeability data are decently comparable. Yet, whether this approach could be generally applicable needs more delicate models and larger training datasets to be determined.

Digital Elevation Models (DEMs) are widely used in geographic and environmental studies. In the current work, the fusion of multi-source DEMs is investigated to improve the overall accuracy of public domain DEMs. Multi-scale decomposition is an important analytical method in data fusion. Three multi-scale decomposition methods – the wavelet transform (WT), bidimensional empirical mode decomposition (BEMD) and nonlinear adaptive multi-scale decomposition (N-AMD) - are applied to the 1-arc-second Shuttle Radar Topography Mission Global digital elevation model (SRTM-1 DEM) and the Advanced Land Observing Satellite World 3D – 30 m digital surface model (AW3D30 DSM) in China. Of these, the WT and BEMD are popular image fusion methods. A new approach for DEM fusion is developed using N-AMD (which is originally invented to remove the cycle from sunspots). Subsequently, a window-based rule is proposed for the fusion of corresponding frequency components obtained by these methods. Quantitative results show that N-AMD is more suitable for multi-scale fusion of multi-source DEMs, taking the ice cloud and land elevation satellite (ICESat) global land surface altimetry data as a reference. The vertical accuracy of the fused DEM shows significant improvements of 29.6% and 19.3% in a mountainous region and 27.4% and 15.5% in a low-relief region, compared to the SRTM-1 and AW3D30 respectively. Furthermore, a slope position-based linear regression method is developed to calibrate the fused DEM for different slope position classes, by investigating the distribution of the fused DEM error with topography. The results indicate that the accuracy of the DEM calibrated by this method is improved by 16% and 13.6%, compared to the fused DEM in the mountainous region and low-relief region respectively, proving that it is a practical and simple means of further increasing the accuracy of the fused DEM.

Cervical cancer is one of the ailments that endangers the health of women all over the world and causes infertility. Fortunately, this disease can be avoided. Both the results and participation rates of the current preventative strategy remain poor. Hence, preventative or early detection methods remain challenging and open. In gynecology and computer science fields, few studies on identifying cervical cancer are based on behavior risk factor and machine learning. Moreover, various social and behavioral aspects might often make it more difficult to detect cervical cancer especially in low‑ and middle‑income countries (LMICs). Accordingly, focus on predicting the presence of cervical cancer through behavioral risk factors is the basic structure of this research. We proposed an approach to classify cervical cancer from a social-behavioral perspective using logistic regression to predict cervical cancer. We got significantly improved outcomes than the existing methods. Moreover, we used feature engineering to formulate less dimensionality as a pre-processing step and optimized parameters to be prepared for classification phase. The results proved that using the logistic regression with regularization type L1 had a promising performance. The accuracy of Logistic Regression (LR) L1 was 97.2%. Such results support the proposed work as a reliable classification predictive tool.

The goal of the project was to understand how topography/bathymetry is imported and used in GeoFlood with an aim towards improving efficiency and computational cost of bathymetry handling in GeoFlood.GeoFlood is a software to simulate overland flooding basing on shallow water equations.Numerical methods and programming were used for this study.The GeoFlood was ran on a given data set (Malpasset data) and it was found out that indeed topography handling during simulations has to be improved to minimise the computational time and also improve the efficiency.Through this research, we also looked at the the shallow water equations, and the numerical techniques used to solve the equations

Eddy-driven jets are of importance in the ocean and atmosphere, and to a first approximation are governed by Rossby wave dynamics. This study addresses the time-dependent flux of fluid and potential vorticity between such a jet and an adjacent eddy, with specific regard to determining zonal and meridional wavenumber dependence. The flux amplitude in wavenumber space is obtained, which is easily computable for a given jet geometry, speed and latitude, and which provides instant information on the wavenumbers of the Rossby waves which maximize the flux. This new tool enables the quick determination of which modes are most influential in imparting fluid exchange, which in the long term will homogenize the potential vorticity between the eddy and the jet. The results are validated by computing backward- and forward-time finite-time Lyapunov exponent fields, and also stable and unstable manifolds; the intermingling of these entities defines the region of chaotic transport between the eddy and the jet. The relationship of all of these to the time-varying transport flux between the eddy and the jet is carefully elucidated. The flux quantification presented here works for general time-dependence, whether or not lobes (intersection regions between stable and unstable manifolds) are present in the mixing region, and is therefore also easily computable for wave packets consisting of infinitely many wavenumbers.

Background: We considered a problem of inference in epidemiology when cumulative exposure is the true dose metric for disease, but investigators are only able to measure its duration on each subject. Methods: We undertook theoretical analysis of the problem in the context of a continuous response caused by cumulative exposure, when duration and intensity of exposure follow log-normal distributions, such that analysis by linear regression is natural. We present a Bayesian method to adjust duration-only analysis to incorporate partial knowledge about the relationship between duration and intensity of exposure and illustrate this method in the context of association of smoking and lung function. Results: We derive equations that (a) describe under what circumstances bias arises when duration of exposure is used as a proxy of cumulative exposure, (b) quantify the degree of such bias and loss of precision, and (c) describe how knowledge about relationship of duration and intensity of exposure can be used to recover an estimate of the effect of cumulative exposure when only duration was observed on every subject. Conclusions: Under our assumptions, when duration and intensity of exposure are either independent or positively correlated, we can be more confident in qualitatively interpreting the direction of effects that arise from use of duration of exposure per se. To make reliable inference about the magnitude of effect of cumulative exposure on the outcome, we can use external information on the relationship between duration and intensity of exposure even if intensity of exposure is not available at the individual level.

The studied solar pot is a recent invention, which gained a utility model protection in 2021 from the Hungarian Intellectual Property Office under patent number 5489. The device is made for environmentally friendly cooking or heating (by utilizing solar energy) of foods and liquids. Its structure is similar to a double pipe heat exchanger, it has an outer mantle and an inner cooking tank. The goals of the paper are proposing a new physically-based mathematical model describing the solar pot and carrying out computer experiments with it, assembling an experimental system of the pot connected with a solar collector and performing measurements on it. Based on the results, the solar pot can successfully be used for cooking or sterilizing foods or liquids during the studied time period, in Hungary.

Mathematical optimization offers a valuable approach to tackle Industry scheduling problems. By formulating the scheduling challenge as a mathematical problem, mathematical optimization enables efficient and effective decision-making processes. Mathematical optimization is particularly beneficial in complex scheduling scenarios, such as in networked manufacturing environments, where multiple jobs and resources need to be coordinated. By leveraging optimization models and algorithms, it becomes possible to generate optimal process plans, considering factors like job dependencies, resource availability, and timing constraints. Through mathematical optimization, organizations can achieve improved efficiency, reduced lead times, and enhanced utilization of resources. Rigorous mathematical formulations and optimization techniques enables to surpass traditional manual planning methods and brings forth powerful computational capabilities. By optimizing various scheduling objectives, from minimizing makespan to maximizing resource utilization, mathematical optimization provides organizations with valuable insights and actionable plans. The purpose of this study is to discuss scheduling solutions for multiple jobs in a networked manufacturing setting based on mathematical optimization process. The study analyses a solver-based approach to generate the optimal process plans for multiple jobs and compare it with a more traditional game-theoretic approach. The objectives aim to develop two solver-based model using Z3 and Gurobi to generate optimal process plans; implement a game-theoretic model to solve for the same set of scheduling problems, and compare the computational time, solution quality, and efficiency of both approaches. To achieve this, the methodology will start with the problem definition. Multiple jobs are to be scheduled on a set of parallel machines. Each job has predefined processing times, deadlines, and priorities. The objective is to minimize the total completion time and maximize machine utilization while meeting all deadlines.

The precipitation, flocculation, and deposition of asphaltene cause severe formation damage within a reservoir and shorten a well’s productive life. Pressure depletion is one factor that contributes to asphaltene precipitation during production; therefore, the first step in managing asphaltene is to determine the onset pressure of the precipitation. While there are numerous equation of state models that can be used to predict the onset pressure, these models are complex and heavily reliant on tuning parameters. Using multivariate linear regression, this work attempts to develop a simple and accurate thermodynamic model for predicting the upper precipitation onset pressure under pressure depletion above the bubble point pressure (Pb) at various temperatures. A total of 94 experimental data points from 37 published crude oil data sets were compiled from the literature. To develop the model, 59 experimental data points were used as training data and 35 experimental data points as testing data. According to the results of the multicollinearity test, the bubble point pressure, temperature, resins, and saturate-to-aromatic ratio were chosen as predictors. The upper onset pressure data with comparable trends were clustered, and unsupervised recognition of three distinct cluster groups was performed. For each cluster identified, a multivariate linear regression model was developed. The model was chosen based on Mallow’s coefficient of determination (Cp), adjusted R² (statistical measure of fit), and S (standard error of the regression slope). The developed model was tested using a data set, and the results showed an adjusted R² of 96.25%, with a mean absolute error of 4.1%. The model was randomly applied to 15 data points to compare it to perturbed-chain statistical associated fluid theory (PC SAFT) and the Peng-Robinson equation of state models and to the multivariate regression models of Fahim (2007) and Ameli et al. (2016). The results showed that the mean absolute error for predicting the asphaltene precipitation onset pressure was 2.82% using Peng-Robinson, 2.36% using the PC SAFT equation of state, 23.96% using the Fahim model, 24.80% using the model reported by Ameli et al., and 2.39% using the newly developed multivariate regression model. The developed multivariate model appears to be as accurate as the PC SAFT equation of state modeling with tuning parameters. The primary advantage of multivariate regression is that, unlike the PC SAFT equation of state model, it does not require saturates, aromatics, resins, and asphaltenes (SARA)-based characterization methodologies or rigorous parameter tuning. It is simple to use, quick, and it produces results in a short period of time.

We introduce NodeFlow, a flexible framework for probabilistic regression on tabular data that combines Neural Oblivious Decision Ensemble (NODE) and Conditional Continuous Normalizing Flows (CNF). It offers improved modeling capabilities for arbitrary probabilistic distributions, addressing the limitations of traditional parametric approaches. In NodeFlow, the NODE captures complex relationships in tabular data through a tree-like structure, while the conditional CNF utilizes the NODE’s output space as a conditioning factor. The training process of NodeFlow employs standard gradient-based learning, facilitating end-to-end optimization of the NODEs and CNF-based density estimation. This approach ensures outstanding performance, ease of implementation, and scalability, making NodeFlow an appealing choice for practitioners and researchers. Comprehensive assessments on benchmark datasets underscore NodeFlow’s efficacy, revealing its achievement of state-of-the-art outcomes in multivariate probabilistic regression setup and its strong performance in univariate regression tasks. Furthermore, ablation studies are conducted to justify the design choices of NodeFlow. In conclusion, NodeFlow’s end-to-end training process and strong performance make it a compelling solution for practitioners and researchers. Additionally, it opens new avenues for research and application in the field of probabilistic regression on tabular data.

The software industry has adopted component-based software development (CBSD) to rapidly build and deploy large and complex software systems with significant savings at minimal engineering effort, cost, and time. However, CBSD encounters issues on security trust, mainly with respect to dependability attributes. A system is considered dependable when it can produce the outputs for which it was designed with no adverse effect on its intended environment. Dependability consists of several attributes that imply availability, confidentiality, integrity, reliability, safety, and maintainability. Dependability attributes must be embedded in a CBSD model to develop dependable component software. Motivated by the importance of these attributes, this paper pursues two objectives: to design a model for developing a dependable system that mitigates the vulnerabilities of software components, and to evaluate the proposed model. The model proposed in this study is labelled as developing dependable component-based software (2DCBS). To develop this model, the CBSD architectural phases and processes must be framed and the six dependability attributes embedded according to the best practice method. The expert opinion approach was applied to evaluate 2DCBS framing. In addition, the 2DCBS model was applied to the development of an information communication technology (ICT) portal through an empirical study method. Vulnerability assessment tools (VATs) were employed to verify the dependability attributes of the developed ICT portal. Results show that the 2DCBS model can be adopted to develop web application systems and to mitigate the vulnerabilities of the developed systems. This study contributes to CBSD and facilitates the specification and evaluation of dependability attributes throughout model development. Furthermore, the reliability of the dependable model can increase confidence in the use of CBSD for industries.

As argued by ‘Declaration of Concrete Environment (2010)’ of Korea and ‘Declaration of Asian Concrete Environment (2011)’ of six Asian countries, concrete as a single material has lately shown extremely large impact on environmental issues such as climate change. Assessment of environmental impact from concrete material and production has considerable importance. Concrete is a major material used in the construction industry that emits a large amount of substances with environmental impacts during its life cycle. Accordingly, technologies for the reduction in and assessment of the environmental impact of concrete from the perspective of Life Cycle Assessment must be developed. At present, the studies in relation to greenhouse gas emission from concrete are being carried out globally as a countermeasure against climate change. In this study, a sustainable concrete mix design algorithm was designed using correlation analyses, and its carbon emission and cost reduction performances were assessed. Using correlation analyses, the concrete strength, w/b and s/a ratios, and CO₂ emissions were identified as major variables of concrete mix design that influenced other variables. Also, this study aims to evaluate the CO₂ emission reduction performance of the algorithm-deduced sustainable concrete mix design, and therefore, the CO₂ emissions of the sustainable concrete mix design are compared with those of the actual concrete mix design applied to the construction of the office building A in South Korea.

We study certain function algebras and their operator algebra completions on r-discrete abelian groupoids, the corresponding conditional expectations, maximal abelian subalgebras (masa) and eigen-functionals.

In this article, a generalization of the geometry of Grassmannian chain complex of free abelian groups generated by the projective configuration of points and Cathelineau's infinitesimal complex of polylogarithmic groups is proposed. Firstly, homomorphisms for weight n =2 up to weight n=6 will be introduced to connect sub-complexes of Grassmannian and Cathelineau. Lately, generalization of these morphisms will be shown for weight n=N. The associated diagrams will also be proven to be commutative and bi-complex.

(1) Background: The prediction of cervical lesions evolution is a challenge for clinicians. The prospective study aimed to determine and compare the predictive accuracy of cytology, HPV genotyping, and p16/Ki67 dual staining alone or in combination with personal risk factors for the prediction of progression, regression or persistence of cervical lesions in human papillomavirus (HPV)-infected patients; (2) Methods: This prospective study included HPV-positive patients with or without cervical lesions that underwent follow-up. Descriptive statistics and sensitivity analysis for individual or combined index tests were used for data analysis; (3) Results: The highest predictive performance for the progression of cervical lesions was achieved by a model that comprised a Pap smear suggestive of high-grade squamous intraepithelial lesion (HSIL), the presence of 16/18 HPV strains, a positive p16/Ki67 dual staining result along with the presence of at least 3 clinical risk factors, which had a sensitivity (Se) of 74.42%, a specificity of 97.92%, an area under the receiver operating curve (AUC) of 0.961, and an accuracy of 90.65%. The prediction of cervical lesions regression or persistence was modest; (4) Conclusions: Multiple testing or new biomarkers should be used to improve HPV-positive patient surveillance, especially for cervical lesion regression or persistence prediction.

Panel data of our interest consist of a moderate number of panels, while the panels contain a small number of observations. An estimator of common breaks in panel means without a boundary issue for this kind of scenario is proposed. In particular, the novel estimator is able to detect a common break point even when the change happens immediately after the first time point or just before the last observation period. Another advantage of the elaborated change point estimator is that it results in the last observation in situations with no structural breaks. The consistency of the change point estimator in panel data is established. The results are illustrated through a simulation study. As a by-product of the developed estimation technique, a theoretical utilization for correlation structure estimation, hypothesis testing, and bootstrapping in panel data is demonstrated. A practical application to non-life insurance is presented as well.

Notion of median in one dimension is a foundational element in nonparametric statistics. It has been extended to multi-dimensional cases both in location and in regression via notions of data depth. Regression depth (RD) and projection regression depth (PRD) represent the two most promising notions in regression. Carrizosa depth DC is another depth notion in regression. Depth induced regression medians (maximum depth estimators) serve as robust alternatives to the classical least squares estimator. The uniqueness of regression medians is indispensable in the discussion of their properties and the asymptotics (consistency and limiting distribution) of sample regression medians. Are the regression medians induced from RD, PRD, and DC unique? Answering this question is the main goal of this article. It is found that only the regression median induced from PRD possesses the desired uniqueness property. The conventional remedy measure for non-uniqueness, taking average of all medians, might yield an estimator that no longer possesses the maximum depth in both RD and DC cases. These and other findings indicate that the PRD and its induced median are highly favorable among their leading competitors.

Considering that cryptocurrencies are now present in practically every financial transaction because they are widely accepted as an alternate means of making payments and exchanging currencies, academics and economists have more opportunities to study cryptocurrency prices. Over the years, investors, traders and investment banks have found it difficult to predict the closing daily price of Ethereum due to its rapid price fluctuation. The daily closing price of cryptocurrency is essential to consider when trading or investing in Ethereum. This report focuses on carrying out a comparative study of the predictive capabilities of deep machine learning algorithms with a stacking ensemble modelling framework using daily historical observations of the price of Ethereum obtained from Coindesk, tweets extracted from Twitter ranging from the 1st of August 2022 to the 8th of August 2022 and other five covariates (closing price lag1, closing price lag2, noltrend, daytype and month) engineered from the closing price of Ethereum. Seven models are used to compute the forecasts for the daily closing price of Ethereum; these are the recurrent neural network, ensemble stacked recurrent neural network, gradient boosting machine, generalized linear model, distributed random forest, deep neural networks and stacked ensemble for gradient boosting machine, generalized linear model, distributed random forest and deep neural networks. The main evaluation metric used is the mean absolute error. According to MAE, RNN forecasts outperform the other model’s forecasts in this study, producing an MAE of 0.0309.

We introduce the notion of generalized contraction on dualistic partial metric spaces. A fixed point theorem for mappings satisfying above mentioned contraction is obtained. Some consequences of our result are obtained. We construct an example to demonstrate the effectiveness of our result among the corresponding results in partial metric spaces. Our results provide substantial generalizations and improvements of several well known results existing in the comparable literature. We discuss an application of our fixed point results to show the existence of solution of functional equations.

Let S be a Fermat surface of degree 5 and let k be an algebraically closed field of characteristic p = 2. We give a fibration ƒ: S → P with upper limit 1 and lower limit k, and investigate the geometric properties of fiber of ƒ. Furthermore, we investigate the fibration-preserving automorphisms group Aut_{Pwith upper limit 1 and lower limit k}(S) of ƒ. We obtain that Aut_{Pwith upper limit 1 and lower limit k}(S) is a p-group of order 256.

This manuscript presents a new two-parameter unit stochastic distribution, obtained by transforming the Laplace distribution, using generalized logistic map, into a unit interval. The distribution thus obtained is named the Laplace-logistic unit (abbreviated LLU) distribution, and its basic stochastic properties are examined in detail. Also, the procedure for estimating parameters based on quantiles is provided, along with the asymptotic properties of the obtained estimates and the appropriate numerical simulation study. Finally, the application of the LLU distribution in dynamic and regression analysis of real-world data with accentuated "peaks" and "fat" tails is also discussed.

This paper investigates the energy dissipation level of a nonlinear vehicle suspension system. The suspension system is modelled as a mass-spring-damper system, which is designed using the output frequency response function (OFRF) method. This method enables the derivation of an explicit relationship, between the system output spectrum (or Performance metric) and the system nonlinear parameters of interest. The OFRF polynomial, of the energy dissipation level, was derived in terms of the nonlinear parameters of interest. The results obtained show that the OFRF model, of the energy dissipation level, could be used to estimate the amount of heat dissipated, for a set of design parameters. This has potentials of providing some insights, in the design of vibration-based energy harvesters, as some of the wasted heat energy could be converted to electrical energy.

In this paper we suggest a first ever construction of fractional integral and differential operators based on signed measures including a vector-valued case. The study focuses on constructing the fractional power of the Riemann-Stieltjes integral with a signed measure, using semigroup theory. The main result is a theorem that provides the exact form of a semigroup for the Riemann-Stieltjes integral with a measure having a countable number of extrema. The article provides examples of semigroups based on integral operators with signed measures and discusses the fractional powers of differential operators with partial derivatives.

In this paper, the transmutation operator method is used to construct an exact solution to the initial boundary value problem for the equation of multidimensional free transverse vibration of a thin elastic plate with a singular Bessel operator acting on geometric variables. We emphasize that multidimensional Erdélyi–Kober operators of fractional order have the property of a transmutation operator, allowing one to transform more complex multidimensional partial differential equations with singular coefficients acting over all variables into simpler ones. If formulas for solutions are known for a simple equation, then we also obtain representations for solutions to the first complex partial differential equation with singular coefficients. In particular, it is successfully applied to the singular differential equations, especially with Bessel-type operators. Using this operator, the considered problem is reduced to a similar problem without the Bessel operator. Based on the solution to the auxiliary problem, an exact solution to the original problem is constructed and analyzed.

This paper represents the first investigation into the consensus problem of linear time-varying multi-agent systems utilizing an event-triggered communication scheme. First, a general event-triggered consensus control scheme is proposed for a general category of linear time-varying multi-agent systems. Under some suitable assumptions, it is demonstrated that all agents’ states will converge exponentially, with Zeno behaviour being ruled out. Second, the consensus problem in a network of linear time-varying multi-agent systems with a spanning tree is investigated using the proposed control strategy. It demonstrates that the consensus issue for the specified system can be reformulated as a stabilization problem for an error system through a time-varying linear transformation. Then, the event-triggered consensus problem is just a special instance of the general event-triggered consensus problem mentioned above. Finally, to illustrate the efficacy of the event-triggered method proposed in this study, simulation results are shown.

This study focuses on calibrating the linear Drucker-Prager yield criterion for polypropylene under multiaxial loading conditions, using the Arcana machine to achieve a wide range of triaxiality states. The Drucker-Prager criterion has been adapted for polymers, composites, and metals due to its ability to account for the influence of hydrostatic pressure on yield stress. This study employs the Arcana machine, which allows for testing flat plate samples under various angles, thereby simulating different stress states from pure shear to biaxial tension. Additionally, uniaxial compression tests were conducted to extend the range of triaxiality. The material used in this study is Sabic 83MF10, a polypropylene polymer. Samples were prepared by injection molding and cut to specific dimensions. Tests were performed using a universal testing machine with the Arcana handle, and the results were analyzed to determine the yield strength, pressure, and triaxiality for each sample. The results showed a linear relationship between von Mises stress and hydrostatic pressure, with a friction angle (β) of 20.65° and material cohesion (d) of 27.81. The numerical simulations in Abaqus confirmed the validity of the Drucker-Prager model, accurately reflecting the moment of yielding for the tested samples.

In a recent paper, Sarikaya et al. introduced a new analogue of the classical Gamma function which they called, the conformable Gamma function. Motivated by their results, this paper seeks to establish some inequalities for the conformable Gamma and Polygamma functions. Among other analytical tools, the procedure relies on the generalized forms of some classical inequalities.

Asymptotic theories for fractional cointegrations have been extensively studied in the context of time series data, with numerous empirical studies and tests developed. However, most of the previously developed testing procedures for fractional cointegration were primarily designed for time series data. This paper proposes a generalized residual-based test for fractionally cointegrated panels with fixed effects. The test development is based on bivariate panel series with the regressor assumed to be fixed across cross-sectional units. The proposed test procedure accommodates any integration order between [0,1], and it is asymptotically normal under the null hypothesis. Monte Carlo experiments demonstrate that the test exhibits better size and power compared to a similar residual-based test across varying sample sizes.

MicroRNAs (miRNA) exert regulatory actions via base-pairing with their binding sites on target mRNAs. Cooperative-binding, i.e., synergism, among binding sites on a mRNA is biochemically well-characterized. We studied whether this synergism is reflected in global relationship between miRNA-mediated regulatory activity and miRNA-binding-site count on the target mRNAs, i.e., leading to a non-linear relationship between the two. Recently, using our own and public datasets, we have enquired into miRNA regulatory actions: first, we analyzed the power-law distribution pattern of miRNA binding sites; second, strikingly, mRNAs for core miRNA regulatory apparatus proteins have extra-ordinarily high binding site counts, forming self-feedback-control loops; third, we revealed that tumor suppressor mRNAs generally have more sites than oncogene mRNAs; and fourth, we characterized enrichment of miRNA target mRNAs in translationally less-active polysomes relative to more-active polysomes. In these four studies, obvious correlation was observed qualitatively between the extent to which a mRNA is miRNA-regulated and its binding sites count. This paper summarizes the used datasets. We also re-analyzed the correlation by comparative linear and non-linear regression analyses. The results support a non-linear, instead of linear, relationship between the two parameters, conceivably a transcriptome-level reflection of cooperative-binding/synergism among miRNA binding sites on a target mRNA.

The philosophy of testing statistical hypothesis is a natural consequence and functional extension of mathematical analysis of Probability. Along with the concept of recurrence when applied to random sequences and functions, it leads to the analysis of a priori and posterior which implies testing statistical hypothesis. Testing statistical hypothesis also involves algebraic, functional and dimensional considerations, which are found in the works of Laplace. Aspects of mathematical analysis such as universality of solutions, Laws of Large Numbers, Entropy, Information, and various functional dependencies are the main factors explained in the five properties that lead to implication of testing statistical hypothesis. Various interesting examples with modern scientific significance from genetics, astrophysics, and other areas give methodological access to answers of different problems and phenomena which are involved in the logic of testing statistical hypothesis.

Under suitable continuity and uniqueness conditions, solutions of an α order Caputo fractional boundary value problem are differentiated with respect to boundary values and boundary points. This extends well-known results for nth order boundary value problems. The approach used is a standard technique and makes heavy use of recent results for differentiation of solutions of Caputo fractional intial value problems with respect to initial conditions and continuous dependence for Caputo fractional boundary value problems.

This paper is motivated by spatio-temporal pattern in the occurrence of Leishmaniasis in Afghanistan and the relatively high number of zero counts. We hold the view that correlations that arise from spatial and temporal sources are inherently distinct. Our method decouples these two sources of correlations, there are at least two advantages in taking this approach. First, it circumvents the need to inverting a large correlation matrix, which is a commonly encountered problem in spatio-temporal analyses. Second, it simplifies the modelling of complex relationships such as anisotropy, which would have been extremely difficult or impossible if spatio-temporal correlations were simultaneously considered. We identify three challenges in the modelling of a spatio-temporal process: (1) accommodation of covariances that arise from spatial and temporal sources; (2) choosing the correct covariance structure and (3) extending to situations where a covariance is not the natural measure of association. Moreover, because the data covers a period that overlaps with the US invasion of Afghanistan, the high number of zero counts may be the result of no disease incidence or lapse of data collection. To resolve this issue, a model truncated at zero built on a foundation of the generalized estimating equations was proposed.

Although, promotion of urbanization culture in recent decades has made inevitable development of cities in the world, however, the development can be guided in a direction that leave, to the extent possible, minimum socioeconomic and environmental impacts. For this, it is required to first forecast auto-spreading orientation of cities and suburbs in rural areas over time and then avoid shapeless growth of cities. This paper is an attempt to develop a dynamic hybrid model based on logistic regression (LR), Markov chain (MC), and cellular automata (CA) for prediction of future urban sprawl in fast-growing cities. The model was developed using 12 widely-used urban development criteria, whose significant coefficient was determined by logistic regression, and validated by relative operating characteristic (ROC) analysis. The validated model was run in Guilan, a tourist province in northern Iran with a very high rate of urban development. For this, changes in the area of urban land use were detected over the period of 1989 to 2013 and then, future sprawl of the province was forecasted by the years 2025 and 2037. The analysis results revealed that the area of urban land use was increased by more than 1.7 % from 36012.5 ha in 1989 to 59754.8 ha in 2013, and the area of Caspian Hyrcanian forestland was reduced by 31628 ha. The results also predicted an alarming increase in the rate of urban development in the province by the years 2025 and 2037, during which urban land use is predicted to develop 0.9 % and 1.38 %, respectively. The development pattern is expected to be uneven and scattered, without following any particular direction. The development will occur close to the existing or newly-formed urban basements as well as around major roads and commercial areas. This development, if not controlled, will lead to the loss of 13863 ha of Hyrcanian forests and if the trend continues, 21013 ha of Hyrcanian forests and 20208 ha of Barren/open lands are expected to be destroyed by the year 2037. In general, the proposed model is an efficient tool for the support of urban planning decisions and facilitates the process of sustainable development of cities by providing decision-makers with an overview on future development of cities where the growth rate is very fast.

This article discusses the application of thermal quality control methods for plant tissues. The purpose of the work is to determine the optimal parameters of thermal impact on a spherical-shaped plant control object, ensuring the detection of surface and subsurface defects. The authors of the work proposed mathematical models of the temperature field for a spherical body with defects and a flat sample when exposed to the thermal influence of a pulsed source. As a result of the use of mathematical models, the thermophysical characteristics of plant tissues of varying degrees of disease damage were obtained, which made it possible to simulate the temperature field of the control object and obtain an image of classified tissues. The developed recommendations made it possible to select the optimal parameters of the thermal effect on the test object.

High-precision conical threads are widely used in responsible joints in the drilling of oil and gas wells. Difficult underground drilling conditions due to the occurrence of significant mechanical loads and an aggressive environment in wells require the use of workable materials that are often difficult to machine. The huge need for such connections dictates the use of high-performance cutting tools, which means that high demands are placed on their effective geometric performance. The study describes the theoretical dependence of the profile precision of the tapered drill-string tool-joint threads of all standard sizes on the complex of a cutting tool geometric parameters and cutting tool setting accuracy. The experiments include an assessment of the geometric accuracy of the profile of the obtained NC23 thread connector, depending on the values of the installation angles and the declared tangential displacement of the standard threaded carbide insert.

Problem solving is one of the most important components of the human cognition that affects for ages the progress of the human society. Mathematical modelling is a special type of problem solving concerning problems related to science or everyday life situations. The present study is a review of the author’s earlier works on problem solving and mathematical modelling from the scope of Education. Its real goal is that it presents in a systematic way and in a few pages only the results of many years research on the subject. This helps the reader to get a comprehensive idea about a very important topic belonging to the core of Mathematics Education, which is very useful to those wanting to study deeper the subject and get directions for further research in the area.

Crop yield estimation supported by satellite remote sensing data can provide expeditious and strategic information for farmers’ decision-making. Most recent forecasting methods have indicated a promising pathway based on machine learning algorithms. However, validation performances, demand for big data and their inherent inexplicability have not yet consolidated a substantial differential to replace methods based on simpler and more understandable models. This paper proposes an approach based on simple linear models fitted from vegetation indices (VIs) assessed at regular intervals of time series derived from MODIS satellite images, aiming to forecast cotton yields in representative areas of the Brazilian Cerrado. Data from 281 commercial production plots were taken to train (167 plots) and test (114 plots) linear regression models relating seed cotton yield and nine well-known VIs averaged in 15-days intervals. Among the evaluated VIs, EVI (Enhanced Vegetation Index) and TVI (Triangular Vegetation Index) showed the lowest root mean square errors (RMSE) and the highest determination coefficients. The best periods for in-season yield prediction were from the 90-105 to 135-150 days after sowing (DAS), i.e. phenological phases corresponding to boll development, open boll and fiber maturation, with lowest RMSE of about 750 kg ha-1 and R2=0.70. The best forecasts for early crop stages were provided by models at the peaks (maximum value of the VI time-series) for EVI and TVI, which occurred around 80-90 DAS. The proposed approach makes the yield predictability more inferable along the crop time series just by providing sowing dates, contour maps and its respective VIs.

Managing a portfolio whose value closely tracks an index by trading only in a subset of the index constituents involves an NP-hard optimisation problem. In the prior literature, it has been suggested to solve this problem using sequential Monte Carlo (SMC, a.k.a. particle filter) methods. However, this literature does not take transaction costs into account, although transaction costs are the primary motivation for attempting to replicate the index by trading in a subset, rather than the full set of index constituents. This paper extends the SMC approach to index tracking to allow for proportional transaction costs and implements this extended method on empirical data for a variety stock indices. In addition to providing a more practically useful tracking strategy by allowing for transaction costs, we find that including a penalty for transaction costs in the optimisation objective can actually lead to better tracking performance.

Anomalous waves and rogue events are closely associated with irregularities and unexpected events occurring at various levels of physics, such as in optics, in oceans and in the atmosphere. Mathematical modeling of rogue waves is a highly actual field of research, which has evolved over the last decades into a specialized part of mathematical physics. The applications of the mathematical models for rogue events is directly relevant to technology development for prediction of rogue ocean waves, and for signal processing in quantum units. In this survey, a comprehensive perspective of the most recent developments in methods for representing rogue waves is given, along with discussion of the devised and forms and solutions. The standard nonlinear Schrödinger equation, the Hirota equation, the MMT equation and further to other models are discussed, and their properties highlighted. This survey shows that the most recent advancement in modeling rogue waves give models which can be used to establish methods for prediction of rogue waves at open seas, which is important for the safety and activity of marine vessels and installations. The study further puts emphasis on the difference between the methods, and how the resulting models form a basis for representing rogue waves in various forms, solitary or with a wave-background. This review has also a pedagogic component directed towards students and interested non-experts, and forms a complete survey of the most conventional and emerging methods published until recently

This work presents the mathematical framework of the Second-Order Comprehensive Adjoint Sensitivity Analysis Methodology for Response-Coupled Forward/Adjoint Linear Systems (abbreviated as “2nd-CASAM-L”), which enables the most efficient computation of exactly obtained mathematical expressions of first- and second-order sensitivities of a generic system response with respect to functions (“features”) of model parameters. Subsequently, the first- and second-order sensitivities with respect to the model’s uncertain parameters, boundaries, and internal interfaces are obtained analytically and exactly, without needing large-scale computations. Within the 2nd-FASAM-L methodology, the number of large-scale computations is proportional to the number of model features (defined as functions of model parameters), as opposed to being proportional to the number of model parameters, which are considerably more than the number of features, being incomparably more efficient and more accurate than any other methods (statistical, finite differences, etc.) for computing exact expressions of response sensitivities (of any order) with respect to the model’s features and/or primary uncertain parameters, boundaries, and internal interfaces. The application of the 2nd-CASAM-L methodology is illustrated using a simplified energy-dependent neutron transport model of fundamental significance in nuclear reactor physics.

To curb the impacts arising from the agricultural sector the actions undertaken by policymakers, and ultimately by the farmers, are of paramount importance. However, finding the best strategy to reduce impacts, and especially assessing the effects of the interactions and mutual influence among farmers, is very difficult. To this aim, this paper shows an application of an agent-based model (ABM) coupled with life cycle assessment (LCA), which also includes multi objective optimization of farming activities (including both crop cultivation and livestock breeding) from an economic and environmental perspective. The environmental impacts are assessed using the impact assessment scores calculated with the Environmental Footprint (EF) 3.0 life cycle impact assessment (LCIA) method and the study is conducted “from cradle to farm gate”. The model is applied to all the farms in Luxembourg, whose network is constructed utilizing neighborhood interactions, through which a parameter known as farmer's green consciousness (GC) is updated at each time step. The optimization module is instantiated at the end of each time step, and decision variables (the number of livestock units and land allocation) are assigned based on profitability and specified environmental impact categories. If only profit optimization is considered (i.e. when farmers’ GC is de-activated), the results show a 9% reduction in the aggregated environmental impacts (obtained as EF “single score”) and a 5.5% increase in overall profitability. At the farm level, simulations display a clear trade-off between environmental sustainability and financial stability, with a 25% reduction in overall emissions possible if farming activities are carried using the EF single score impact in the objective function, though this results in an 8% reduction in profitability over ten years.

Computer simulation of normal and diseased human heart activity requires a 3D anatomical model of the myocardium, including myofibres. For clinical applications, such a model has to be constructed based on routine methods of cardiac visualisation such as sonography. Symmetrical models are shown to be too rigid, so an analytical non-symmetrical model with enough flexibility is necessary. Based on previously made anatomical models of the left ventricle, we propose a new, much more flexible spline-based analytical model. The model is fully described and verified against DT-MRI data. We show a way to construct it on the basis of sonography data. To use this model in further physiological simulations, we propose a numerical method to utilise finite differences in solving the reaction-diffusion problem together with an example of scroll wave dynamics simulation.

Fresnel incoherent correlation holography (FINCH) is a well-established incoherent imaging technique. In FINCH, three self-interference holograms are recorded with calculated phase differences between the two interfering, differently modulated object waves and projected into a complex hologram. The object is reconstructed without the twin image and bias terms by a numerical Fresnel back propagation of the complex hologram. A modified approach to implement FINCH by a single camera shot by pre-calibrating the system involving recording of the point spread function library and reconstruction by a non-linear cross-correlation has been introduced recently. The expression of the imaging characteristics from the modulation functions in original FINCH and the modified approach by pre-calibration in spatial and polarization multiplexing schemes are reviewed. The study reveals that a reconstructing function completely independent of the function of the phase mask is required for the faithful expression of the characteristics of the modulating function in the image reconstruction. In polarization multiplexing method by cross-correlation, a partial expression was observed, while in spatial multiplexing method by cross-correlation, the imaging characteristics converged towards a uniform behavior.

Splines and quasi-interpolation operators are important both in approximation theory and applications. In this paper, we construct a family of quasi-interpolation operators for the bivariate quintic spline spaces S₅³ (∆_mn⁽²⁾). Moreover, the properties of the proposed quasi-interpolation operators are studied, as well as its applications for solving two-dimensional Burgers’ equation and image reconstruction. Some numerical examples show that these methods, which are easy to implement, provide accurate results.

For a nonzero normed linear space X‎, ‎we will define some different classes of fuzzy norms on X generated by linear and bounded linear functionals‎. ‎Also separate continuity of the elements of each class are investigated‎. ‎The aim of this research is to introduce a source of examples and counterexamples in the field of fuzzy normed spaces‎.

Observed ENSO statistics exhibits a non-gaussian behavior, which is indicative of the presence of nonlinear processes. In this paper we use the Recharge Oscillator model (ROM), a largely used Low-Order Model (LOM) of ENSO, as well as methodologies borrowed from the field of statistical mechanics to identify which aspects of the system may give rise to nonlinearities that are consistent with the observed ENSO statistics. In particular, we are interested in understanding whether the nonlinearities reside in the system dynamics or in the fast atmospheric forcing. Our results indicate that one important dynamical nonlinearity often introduced in the ROM cannot justify a non-gaussian system behavior, while the nonlinearity in the atmospheric forcing can instead produce a statistics similar to the observed. The implications of the non-Gaussian character of ENSO statistics for the frequency of extreme El Nino events is then examined.

As society becomes more reliant on Lithium-ion (Li-ion) batteries, state-of-health (SOH) estimation will need to become more accurate and reliable. Therefore, SOH modelling is in the process of shifting from using simple and continuous charge/discharge profiles, to more dynamic profiles constructed to mimic real operation, when ageing the Li-ion batteries. However, in most cases, when ageing the batteries, the same exact profile is just repeated until the battery reaches its end-of-life. Using data from batteries aged in this fashion to build a model, there is a very real possibility that the model will rely on the built-in repetitiveness of the profile. Therefore, this work will examine the dependence of the performance of a multiple linear regression on the number of charges used to train the model, and their location within the profile used to age the batteries. The investigation shows that it is possible to build models using randomly selected partial charges while still reaching errors as low as 0.5%. Furthermore, it shows that only two randomly sampled partial charges are needed to achieve errors of less than 1%. Lastly, as the number of randomly sampled partial charges used to create the model increases, then the dependence on particular partial charges tends to decrease.

This paper presents a two-stage ADC based on pseudo-differential operational transconductance amplifier (OTA), which is designed for the readout circuit of X-ray linear array sensor. This hybrid ADC employs an incremental sigma-delta ADC and a cyclic ADC, achieving a good trade-off between accuracy and conversion speed. The two stages share the same hardware to reduce power consumption and die area. A common-mood feedback module is used to suppress the influence of charge injection, and the effectiveness is demonstrated by detailed theoretical analysis. A test chip of 14-bit ADC is fabricated in 0.35μm CMOS technology. The measured root mean square (RMS) value of DNL is 0.254 LSB, and the maximum value of INL is -0.776/+1.56 LSB. The measured effective number of bits (ENOB) is 13.43 bits.

Linear-width is a well-regarded width parameter in graph theory. The constructs of linear loose tangle and linear tangle present obstacles to attaining linear-width. In this succinct paper, our primary focus will be the exploration of maximal linear loose tangles.

This work promotes new methods in Mathematical Modeling, consisting in the use of the methods of Non-standard Analysis in Topoi, having as its main purpose, the mathematical definitions of the pseudoparticles from the title, with arguments from Biology/Physiology (Mathematical Neuroscience), Physics (String Theory and Emergent Quantum Mechanics), and Cybernetics (Global Brain, including Natural and Artificial Intelligence). The connections between brain and mind will be scketched via the genetic/epigenetic interplay. The topoi model the intuitionistic logic (multi-valued) and have been used in Quantum Physics while Non-Standard Analysis in SET (= the Category of sets) has been applied in Mathematical Economics; topics from Theory of Categories were also used in the study of Consciousness; however, the combination topoi - non-standard analysis was never used until now in Applied Mathematics. Another important objective is to produce progress in this aria of Pure Mathematics also - the build of non-standard analysis in classes of topoi, already used in Physics. We propose the logic of non-standard extensions in topoi as a model of the human thinking (based on infons/receptons), these theories representing new top and very difficult results in Abstract Mathematics either.

Objective: To evaluate the variables influencing the length of stay (LoS) for COVID-19 ICU patients at Tygerberg Hospital (Cape Town) and to identify the covariates that significantly influenced it and any potential risk factors associated with LoS. Methods and Results: Poisson, negative binomial (NB), Hurdle–Poisson, and Hurdle–NB regression models were used to model the LoS in this prospective cohort study. The fitted models were compared using the Akaike information criterion (AIC), Vuong’s test criteria, and Rootograms. Based on the chosen performance criteria, the NB model provided the best fit outperforming other candidate models. The baseline LoS count was 8 days. On average, antibiotics reduced LoS by 0.74-fold (95% CI 0.62-0.89) compared to not taking antibiotics. The second wave had a significant effect on the average LoS, which decreased by 0.36-fold (95% CI 0.14-0.93) compared to the first wave. Average LoS increased by 1.01-fold (95% CI 1.01-1.02) for every one-year increase in the age of the patient and by 1.02-fold (95% CI 1.01-1.03) for every 1 unit increase in neutrophils. A 1 ng/L increase in log (TropT) levels decreased the average LoS by 0.87-fold (95% CI 0.81-0.93) similarly, a unit increase in the PF ratio decreased the average LoS by 0.998-fold (95% CI 0.997-0.999) respectively. Conclusion: The study identified common clinical characteristics associated with length of stay in ICU for COVID-19 patients, including age at admission, PF ratio, neutrophils, TropT, Wave, and antibiotic use. These results can aid in identifying risk factors for increased length of stay, assist in healthcare systems planning, and aid in evaluating different models for analysing this type of data.

Keywords: Marine Coasts; Protected Areas; Defense and Conservation; Asbestos Cement Materials; Wastes; Contamination; Human Health Risk; Medical Geology.

There are many uncertainties and risks in residential electricity consumption during the economic development. Knowledge of the relationship between residential electricity consumption and its key determinant—income—are important to the sustainable development of electric power industry. Using panel data from 30 provinces for the 1995-2012 period, this study investigates how residential electricity consumption changes as incomes increase in China. Previous studies typically used linear or quadratic double-logarithmic models imposing ex ante restrictions on the indistinct relationship between residential electricity consumption and income. Contrary to those models, we employed a reduced piecewise linear model that is self-adaptive and highly flexible and circumvents the problem of “prior restrictions.” Robust tests of different segment specifications and regression methods are performed to ensure the conservatism of the research. The results provide strong evidence that the income elasticity was approximately one, and it remained stable throughout the estimation period. The income threshold at which residential electricity consumption automatically remains stable or slows has not been reached. To ensure the sustainable development of the electric power industry, introducing higher energy efficiency standards for electrical appliances and improving income levels are vital. And government should emphasize electricity conservation in industrial sector rather than in residential sector.

The increase in population and the challenges caused by it are always among the concerns of decision-makers and policymakers in large countries. One of the most serious concerns is in the field of energy consumption. Optimizing energy use is one of the most effective ways to manage limited resources and energy. Energy consumption in residential houses constitutes a significant percentage of the total energy consumption worldwide; therefore, current research focusing on mathematical models aims to provide a predictive multi-objective linear mathematical model for residential house consumption. For this purpose, the consumption of water, electricity, and gas for 80 residential houses, including 10 household appliances and equipment on a weekly basis, has been considered. The results showed that the mixed-integer multi-objective predictor model is able to optimize household consumption plans compared to the actual state of household energy consumption. Since the goals of household satisfaction and energy consumption costs in the model conflict with each other, the influence coefficient was calculated to demonstrate the simultaneous achievement of these goals. The optimal value achievable with the default model for the model's purposes is 69%.

Article explores participant specific study of muscle inherehit dynamics hidden inside the diognostic electromyography (D-EMG) signals during load pull exercises, aiming to uncover underlying patterns and nonlinear behaviors. Employing a multi-step analytical framework, the study first evaluates signal stationarity through Quantile-Quantile (Q-Q) plot and surrogate data analyses, revealing insights into signal stability. Subsequent use of phase space reconstruction techniques exposes intrinsic dynamics within the EMG signals, visualized through Poincar´e maps, elucidating attractor geometry and system dynamics. Histogram analysis further dissects the Poincar´e maps, offering insights into signal behavior relative to physiological processes. Additionally, the study quantifies the largest Lyapunov exponent from the Poincar´e maps, providing a measure of dynamical complexity within the muscle EMG signals during load pull exercises. By integrating these methods, this research sheds light on the nuanced interplay between EMG signals and muscle activity during dynamic exercises, offering valuable insights for rehabilitation strategies.

The efficient preparation of single-stranded DNA (ssDNA) rings, as a macromolecular construction approach with topological features, has aroused much interest due to their numerous applications in biotechnology and DNA nanotechnology. However, an extra splint is essential for enzymatic circularization, and by-products of multimers are usually present at high concentrations. Here, we proposed a simple and robust strategy of using permuted precursor (linear ssDNA) for circularization by forming an intramolecular dynamic nick using a part of the linear ssDNA substrate itself as the template. After the simulation of the secondary structure for desired circular ssDNA, the linear ssDNA substrate is designed to have its ends on the duplex part (≥5 bp). By using this permuted substrate with 5'-phosphate, the splint-free circularization is simply carried out by T4 DNA ligase. Very interestingly, formation of only several base pairs (2–4) flanking the nick is enough for ligation, although they form only instantaneously under ligation conditions. More significantly, the 5 bp intramolecular duplex part commonly exists in genomes or functional DNA, demonstrating the high generality of our approach. Our findings are helpful for understanding the mechanism of enzymatic DNA ligation from the viewpoint of substrate binding.

In this work we looked for a stable and accurate procedure to perform feature selection in datasets with a much higher number of predictors than individuals, as in Genome-Wide Association Studies. Due to the instability in feature selection when many potential predictors are measured, a variable selection procedure is proposed that combines several replications of shrinkage regression models. A weighted formulation is used to define the final predictors. The procedure is applied to investigate Single Nucleotide Polymorphisms (SNPs) predictors associated to Alzheimer’s disease in the Alzheimer’s disease Neuroimaging Initiative (ADNI) dataset. Two data scenarios are investigated: one considering only the set of SNPs and another with the covariates age, sex, educational level and APOE4 genotype. The SNP rs2075650 and the APOE4 genotype are given as risk factors for AD, which is in line with the literature, and other four new SNPs are pointed, opening new hypotheses for in vivo analyses. These experiments demonstrate the potential of the new method for stable feature selection.

In this note we introduce the notion of polynions and discuss their mathematical relevance. We note that the well-known mathematical structures like quaternions, octonions and sedenions etc. are special cases of polynions.

Genetic similarity determines the extent to which two genotypes share common genetic material. It can be measured in various ways, such as comparing DNA sequences, proteins, or other genetic markers. The significance of genetic similarity is multifaceted and encompasses various fields, including evolutionary biology, medicine, forensic science, animal and plant breeding, and anthropology. Genetic similarity is an important concept with wide application across different scientific disciplines. In the presented study, six measures for calculating genetic similarity were compared: Euclidean, Jaccard, Kulczyński, Sokal and Michener, Nei, and Rogers. The research material included 21 rapeseed genotypes (ten interspecific Brassicaceae hybrids of F2 generation, and 11 of their parental forms) and 146 alleles, obtained using 21 ISSR molecular markers. The results indicate that the research material was divided into two identical groups using any of the proposed methods, despite differences in the values of genetic similarity coefficients. Two of the presented measures of genetic similarity (Sokal and Michener, and Euclidean) were the same.

As known all physical properties of solids are described well by the system of quantum linear harmonic oscillators. It is shown in the present paper that the system consisting of classical linear harmonic oscillators having temperature dependent masses or (and) frequencies has the same partition function as the system consisting of quantum linear harmonic oscillators having temperature independent masses and frequencies while the means of the square displacements of the positions of the oscillators from their mean positions for the system consisting of classical linear harmonic oscillators having: the temperature dependent masses; temperature dependent frequencies; and temperature dependent masses and frequencies differ from each other and from that of the system consisting of quantum linear harmonic oscillators, and hence, the system consisting of classical linear harmonic oscillators describes well the thermodynamic properties of the system consisting of quantum linear harmonic oscillators and solids.

As prominent oil producers, the Gulf Cooperation Council (GCC) countries have played a significant role in the global energy market. However, as the world's attention increasingly shifts towards environmental sustainability, understanding the implications of the GCC's economic activities on CO2 emissions becomes indispensable. This research paper investigates the relationship between specific economic indicators and their impact on CO2 emissions in the GCC from 2001 to 2021. The study employs quantile regression, a powerful statistical method that estimates the conditional quantiles of a response variable given a set of predictor variables. The findings reveal several important insights: Financial institution efficiency is significant and negative at a 1% level at the lower (10th) -83537.3 and the higher quantile (90th) -549002.3. The relationship between GDP per capita and CO2 emissions varies across quantiles, highlighting the complexity of the growth-environment nexus. Total patents exhibit a positive and significant relationship with emissions, underscoring the importance of directing innovation towards environmentally sustainable solutions. Renewable energy consumption displays a nuanced relationship with CO2 emissions, with a stronger negative impact observed at higher consumption levels. This underscores the potential of renewable energy to mitigate emissions when integrated at scale. The study's outcomes hold crucial policy implications for the GCC countries as they seek to align economic growth with environmental sustainability. The findings emphasize the importance of fostering financial institution efficiency, promoting green innovation, and expanding renewable energy sources to reduce emissions

Linear Hashing is an important algorithm for many key-value stores. Spiral Storage was invented to overcome the poor fringe behavior of Linear Hashing, but after an influential study by Larson, seems to have been discarded. Since almost 50 years have passed, we repeat Larson’s comparison with in-memory implementation of both to see whether his verdict still stands. Our study shows that Spiral Storage has slightly better look-up performance, but slightly poorer insert performance.

We suppose that a Cooper pair (CP) will experience a damping force exerted by the condensed matter. A Langevin equation of a CP in two dimensional condensed matter is established. Following a method similar to Nelson's stochastic mechanics, generalized Schr\"{o}dinger equation of a CP in condensed matter is derived. If the CPs move with a constant velocity, then the corresponding direct current (DC) electrical conductivity can be calculated. Therefore, a Drude like formula of resistivity of CPs is derived. We suppose that the damping coefficient of CPs in two dimensional cuprate superconductors is a linear function of temperature. Then the resistivity and scattering rate of CPs turn out to be also linear-in-temperature. The origin of linear-in-temperature resistivity and Planckian dissipation in cuprate superconductors may be the linear temperature dependence of the damping coefficient of CPs.

In this paper, we compile the fractional power series method and the Laplace transform to design a new algorithm for solving the fractional Volterra integro-differential equation. For that, we assume the Laplace power series (LPS) solution in terms of power q=1m,m∈Z+, where the fractional derivative of order α=qγ for which γ∈Z+. This assumption will help us to write the integral, the kernel, and the nonhomogeneous terms as a LPS with the same power. The recurrence relations for finding the series coefficients can be constructed using this form. To demonstrate the algorithm's accuracy, the residual error is defined and calculated for several values of the fractional derivative. Two strongly nonlinear examples are discussed to provide the efficiency of the algorithm. The algorithm gains powerful results for this kind of problem. Under Caputo meaning the obtained results are illustrated numerically, and graphically. Geometrically, the behavior of the solution declares that the changing of the fractional derivative parameter values' in their domain alters the style of the attained solution in a symmetrical meaning and fully coinciding to the ordinary derivative value'. From these simulations, the results report that the recommended novel algorithm is a straightforward, accurate, and superb tool to generate analytic-approximate solutions for Integral, and integro-differental equations of fractional order.

In this article, we consider a class of nonsmooth interval-valued multiobjective semi-infinite programming problems with vanishing constraints (in short, NIMSIPVC). We introduce the VC-Abadie constraint qualification (in short, VC-ACQ) for NIMSIPVC and employ it to establish Karush-Kuhn-Tucker (in short, KKT)-type necessary optimality conditions. Related to NIMSIPVC, we formulate interval-valued vector Lagrange type dual and scalarized Lagrange type dual problems. Subsequently, we establish weak, strong, and converse duality results relating NIMSIPVC and corresponding dual problems. In addition, we introduce the notions of saddle points for interval-valued vector Lagrangian and scalarized Lagrangian of NIMSIPVC. Moreover, we establish the saddle point optimality criteria for NIMSIPVC. Various non-trivial examples are provided to demonstrate the validity of established results. To the best of our knowledge, optimality conditions, Lagrange type duality, and saddle point optimality criteria for NIMSIPVC have not been investigated yet via Clarke subdifferentials.

Investigation of functional magnetic resonance imaging (fMRI) data with machine learning (ML) techniques, including also deep learning (DL) methods, have been widely used to study Autism Spectrum Disorder (ASD). This disorder is characterized by symptoms that affect the individual’s behavioral aspects and social relationships. Early diagnosis is crucial for intervention, but the complexity of ASD poses challenges for treatment development. This study compares traditional ML techniques with deep learning (DL) methods in the analysis of functional connectivity measures obtained from the time series of multicentric ABIDE dataset. Specifically, Support Vector Machines (SVM) classifiers, with both linear and Radial Basis Function (RBF) kernels, as well as eXtreme Gradient Boosting (XGBoost) classifiers, are compared against the TabNet classifier, which is a DL architecture customized for tabular data analysis and a Multi Layer Perceptron (MLP). The findings suggest that DL classifiers may not be optimal for the type of data analyzed, as their performance trails behind that of standard classifiers. SVMs achieve performances, in terms of AUC, around 75%, compared to the best TabNet and MLP results, which are 65% and 71%, respectively. Additionally, this work investigates the brain regions that contribute most to the classification task, which are found to be those primarily responsible for sensory and spatial perception, as well as attention modulation, known to be altered in ASD.

Sharing confidential information is a critical concern in today’s world. Secret sharing schemes facilitate the sharing of secrets in a way that ensures only authorized participants (shareholders) can access the secret using their allocated shares. Hierarchical secret sharing schemes (HSSSs) build upon Shamir’s scheme by organizing participants into different levels based on priority. Within HSSS, participants at each level can reconstruct the secret if a specified number, denoted as the threshold value (t), or more of them are present. Each level has a predetermined threshold value. If the number of participants falls below the threshold at any level, higher-level participants must be involved in reconstructing the secret at lower levels. Our paper proposes schemes that implement hierarchical access structures and enable the sharing of multiple secrets. Additionally, our proposed scheme includes share verification. We have analyzed potential attacks and demonstrated the scheme’s resistance against them. Through security analysis and comparison with existing schemes, we highlight the novelty and superiority of our proposed approach, contributing to advancements in secure information sharing practices.

Expectation maximization (EM) algorithm is a powerful mathematical tool for estimating statistical parameter when data sample contains hidden part and observed part. EM is applied to learn finite mixture model in which the whole distribution of observed variable is average sum of partial distributions. Coverage ratio of every partial distribution is specified by the probability of hidden variable. An application of mixture model is soft clustering in which cluster is modeled by hidden variable whereas each data point can be assigned to more than one cluster and degree of such assignment is represented by the probability of hidden variable. However, such probability in traditional mixture model is simplified as a parameter, which can cause loss of valuable information. Therefore, in this research I propose a so-called conditional mixture model (CMM) in which the probability of hidden variable is modeled as a full probabilistic density function (PDF) that owns individual parameter. CMM aims to extend mixture model. I also propose an application of CMM which is called adaptive regressive model (ARM). Traditional regression model is effective when data sample is scattered equally. If data points are grouped into clusters, regression model tries to learn a unified regression function which goes through all data points. Obviously, such unified function is not effective to evaluate response variable based on grouped data points. The concept “adaptive” of ARM means that ARM solves the ineffectiveness problem by selecting the best cluster of data points firstly and then evaluating response variable within such best cluster. In order words, ARM reduces estimation space of regression model so as to gain high accuracy in calculation.

The main purpose of this paper is to present a comprehensive view of the application mathematical models in the designing and implementing SSCM beside to solving problems and making decision. The research questions are: what mathematical models are used for designing and implementing sustainable supply chain management, how to use them, which industries implemented in, what modules of SSCM depth in and finally finding the gaps of researches. The methodology of research is Systematic Literature review through peer review papers which are published in high ranking journals. In this paper, First, we search all papers through scientific data bases like Scopus, science direct, MDPI, Springer, Google Scholar, then, screening papers based on the criteria such as subject of paper, journals impact factor which is published in-should be peer review journal- and relative content of the papers. Finally, we selected 245 papers with three steps screening through 2806 papers that they have enough quality and relative to our research goals for context analysis. Through context analysis, first we categorized the information of the papers and drew the current situation of researches in the framework of our topic. Then, we evaluate and compare the goals of sustainability and current situation and found the gapes, then, offered new suggestions like implementing SSCMs models in pollutant industries like casting industry, Heavy industry, coal Industry and so on. On the other hand, there are gaps in researches in some modules of SSCM such as packaging, designing products, etc.

Hybrid power plants have recently emerged as reliable and flexible electricity generation stations by combining multiple renewable energy sources, energy storage systems (ESS), and fossil-based output. However, the effective operation of the hybrid power plants to ensure continuous energy dispatch under challenging conditions is a complex task. This paper proposes a dispatch engine (DE) based on mixed-integer linear programming (MILP) for the planning and management of hybrid power plants. To maintain the committed electricity output, the dispatch engine will provide schedules for operation over extended time periods as well as monitor and reschedule the operation in real-time. Through precise prediction of the PV and wind power output, the proposed approach guarantees optimum scheduling. The precise prediction of the PV and wind power are achieved by employing a predictor of Feed-Forward Neural Network (FFNN) type. With such a dispatch engine, the operational cost of the hybrid power plants, and the use of diesel generators (DGs) are both minimized. A case study is carried out to assess the proposed dispatch engine feasibility. A real-time measurement data pertaining to load, wind, and PV power outputs is obtained from different locations in the Sultanate of Oman. The real-time data is utilized to predict the future output power from PV and the Wind farm over 24 hours. The predicted powers are then used in combination with a PV-Wind-DG-ESS-Grid hybrid plant to evaluate the performance of the proposed dispatch engine. The proposed approach is implemented and simulated using MATLAB. The results of the simulation reveal the proposed Feed-Forward Neural Network’s (FFNN) powerful forecasting abilities. In addition, the results demonstrate that adopting the proposed DE can minimize the use of DG units and reduce plant running expenses.

A family of linear singularly perturbed Cauchy problems is studied. The equations defining the problem combine both partial differential operators together with the action of linear fractional transforms. The exotic geometry of the problem in the Borel plane, involving both sectorial regions and strip-like sets, gives rise to asymptotic results relating the analytic solution and the formal one through Gevrey asymptotic expansions. The main results lean on the appearance of domains in the complex plane which remain intimately related to Lambert W function, which turns out to be crucial in the construction of the analytic solutions. On the way, an accurate description of the deformation of the integration paths defining the analytic solutions and the knowledge of Lambert W function are needed in order to provide the asymptotic behavior of the solution near the origin, regarding the perturbation parameter. Such deformation varies depending on the analytic solution considered, which lies in two families with different geometric features.

Tsunami is a type of infrequent geohazards with devastating consequences, which makes accurate computer simulations of tsunami waves particularly desirable for hazard assessment and mitigation purposes. The evolution of a typical tsunami involves the generation, propagation and inundation phases. In this survey, we briefly describe the most common types of tsunamigenic sources and give a detailed review of some most widely used mathematical models for describing tsunami propagation. We emphasize the approximations adopted in each mathematical model and point out their most important advantages and disadvantages. Tsunami propagation modeling is computationally demanding, involving a wide span of spatial and temporal scales. While some of the approximate models are sufficiently accurate for describing wave behaviors at certain scales, they might not be applicable at other scales. Effective and efficient tsunami propagation simulations will likely depend upon the proper coupling of different models for different scales.