Despite polycarbonate (PC) being a widely used engineering plastic, its notch and crack sensitivity pose challenges in critical applications. To address this, PC was blended with elastomeric polymers to explore the improvement in toughness. This study systematically investigates the toughening mechanisms of PC blended with acrylonitrile-butadiene-styrene (ABS), copolyether ester elas-tomer (COPE), and ABS and styrene-ethylene-butylene-styrene (SEBS) copolymer grafted with maleic anhydride (MA). The morphology and mechanical behavior were evaluated under qua-si-static and high-speed tensile tests and Charpy impact tests using optical, electronic, and atomic force microscopy and Raman spectroscopy. The morphological analysis reveals cavitation and crazing phenomena for COPE and SEBS-g-MA systems, and mostly debonding for ABS, indicating an improvement in toughening. While the addition of ABS improves the PC plastic deformation, modifying ABS with maleic anhydride enhances the elastic modulus. Blending PC with SEBS-g-MA increases the strain at break, and the addition of COPE significantly improves the deformation behavior of PC (by around 115%). This comparative study provides valuable insights into the performance of different PC-elastomer blends under similar conditions, supporting the selection of appropriate materials for given applications.

Diabetes is a major health concern that the next-generation of on-demand insulin releasing implants may overcome for personalized therapy. Therein, 3D-printed phenylboronic acid-containing subcutaneous implants with on-demand glucose-triggered drug release abilities are produced using high resolution stereolithography technology. To that end, the methacrylation of phenylboronic acid is targeted following a two-step reaction. The resulting photocurable phenylboronic acid derivative is accordingly incorporated within bioinert polyhydroxyethyl methacrylate-based hydrogels at varying loadings. The end result are sub-centimeter scaled 3D-printed bionert implants that can be remotely activated with 1,2-diols and 1,3-diols such as glucose for on-demand drug administration such as insulin. As a proof of concept, varying glucose concentration from hypoglycemia to hyperglycemia levels readily allow the release of pinacol, i.e. a model molecule with similar release properties than insulin, at respectively low and high rates. In addition, the results demonstrated that adjusting the geometry and size of the 3D-printed part is a simple and suitable method for tailoring the release behavior and dosage.

In this study a material based on Polyethylene (PE) and Microcrystalline Cellulose (MC) was developed as a breathable packaging film. Surface functionalization of MC with 3 aminopropyltriethoxysilane (APTES) shows to be an efficient alternative to tailor their properties and increase opportunities for the application of MC on the reinforcement of polymers such polyethylene (PE). Functionalization of MC with mentioned silane derivative was achieved using a green method and later used on the development of composites with PE in three percentages (1, 3 and 5%). All the materials were prepared by melt blending and characterized, in terms of structural properties (ATR-FTIR and FTIR in transmittance, EDX, SEM), thermal properties (DSC and TGA), thermomechanical properties (DMA), contact angle measurements and permeability to oxygen and water vapor. The materials demonstrated to have potential to be used as breathable film packaging of fresh products.

Microparticles derived from biomaterials are becoming increasingly popular for various applications, particularly in drug delivery systems. In this study, the water-in-oil (W/O) emulsification-diffusion method was used to create cellulose (C), silk fibroin (SF), and C/SF composite microparticles. We then observed the morphology of all obtained microparticles using scanning electron microscopy (SEM), evaluated their functional groups using attenuated total reflection Fourier transform infrared spectroscopy (ATR-FTIR), and conducted thermogravimetric analysis using a thermogravimetric analyzer (TGA). SEM micrographs indicated that the native SF microparticles have the highest spherical shape with smooth surfaces. With blue dextran, the C microparticle was smaller compared to the native microparticle, while the drug-loaded SF microparticles were bigger than the native microparticle. The morphological surfaces of the C/SF composite microparticles were varied in shape and surface depending on the C/SF ratio used. The spherical shape of the C/SF composite microparticle was increased as SF content increased. Furthermore, the size of drug-loaded C/SF composite microparticles was gradually increased by the SF content. The significant functional groups in the C and SF structures were identified based on the ATR-FTIR data, and a suggestion was made regarding the interaction between the functional groups of each polymer. When compared to both native polymers, the C/SF composite microparticles exhibit improved thermal stability. The C/SF composite microparticle at a 1:3 ratio had the lowest drug release content, whereas the hydrophilicity of the C microparticle affected the highest drug release content. As a result, one crucial factor affecting the medication released from the microparticle is its thermal stability. According to the obtained results, C, SF, and C/SF composite microparticles show promise as delivery systems for drugs with controlled release.

Negative temperature coefficient (NTC) materials are usually based on ceramic semiconductors and electrons are involved in their transport mechanism. A new type of NTC material, adequate for alternating current (AC) applications, is represented by zeolites. Indeed, zeolites are single-charge carrier ionic conductors with a temperature-dependent electrical conductivity. In particular, electrical transport in zeolites is due to the monovalent charge-balancing cations, like K⁺, capable of hopping between negatively charged sites in the aluminosilicate framework. Owing to the highly non-linear electrical behavior of the traditional electronic NTC materials, the possibility to have alternative types of materials, showing linearity in the electrical behavior, is very desirable. Among different zeolites, the natural clinoptilolite has been selected for investigating the NTC behavior since it is characterized by high zeolite content, convenient Si/Al atomic ratio, good mechanical strength, due to its compact microstructure, and low toxicity. Clinoptilolite has shown a rapid and quite reversible impedance change under heating, characterized by a linear dependence on temperature. X-ray diffraction (XRD) has been used to identify the natural zeolite, to establish all types of crystalline phases present in the mineral, and to investigate the thermal stability of these phases up to 150°C. X-ray photoelectron spectroscopy (XPS) analysis has been used for the chemical characterization of the natural clinoptilolite sample, providing important information on the cationic content and framework composition. In addition, since electrical transport takes place in the zeolite free-volume, a Brunauer–Emmett–Teller (BET) analysis of the mineral has been also performed.

Electrospun ultrathin fibers based on binary compositions of polylactide (PLA) and poly(ε-caprolactone) (PCL) with different ratios of polymer components from 0/100 to 100/0 wt. % were studied. Using a combination of thermal (DSC) and relaxation (EPR) measurements, the effect of biopolymers content on the characteristics of the crystal structure of PLA and PCL and the diffusive rotational mobility of the stable TEMPO radical in the amorphous regions of PLA/PCL compositions was shown. It was revealed that after PLA and PCL blending, significant changes in the degree of crystallinity of PLA, PCL segmental mobility, sorption capacity of the radical as well as activation energy of rotational diffusion in the amorphous regions of PLA/PCL composition are observed. The characteristic region of biopolymers’ composition from 50/50 to 30/70 % PLA/PCL blends ratio was found, where the inversion transition of PLA from dispersive medium to dispersive phase where an inversion transition is assumed when the continuous medium of the PLA transforms into a discrete phase. The performed studies made it possible for the first time to carry out a comprehensive analysis of the effect of the system component ratio on the structural and dynamic characteristics of the PLA/PCL film material at the molecular level.

Background: Removable prostheses have seen a fundamental change recently because of advances in polymer materials, allowing improved durability and performance. Despite these advancements, notable differences still occur amongst various polymer materials and processing technologies, requiring a thorough grasp of their mechanical, physical, and therapeutic implications. Methods: Fours different processing techniques, all utilizing Polymethyl methacrylate (PMMA) as the main material, were used to construct complete dentures. The specimens underwent a mechanical test. Results: All the specimens broke under the influence of a certain force, rather than yielding through flow, as is characteristic for plastic materials. For each specimen, the maximum force (N) was recorded (figure 4), as well as the breaking energy, Conclusions: The best results were obtained in the case of the thermoplastic injection system and, surprisingly and contrary to those in the specialized literature, the worst results were recorded in the case of 3D printed samples.

Thermal camouflage is a highly sought-after technology to increase the survivability of military equipment against infrared (IR) detectors. Recently, two-dimensional (2D) nanomaterials have shown low IR emissivity, widely tunable opto-electronic properties and compatibility with stealth-applications. Among them, graphene and graphene-like materials are the most attractive 2D materials used for thermal camouflage applications. In particular, in multilayer graphene (MLG) charge density can be effectively tuned through sufficiently intense electric fields or through electrolytic gating. Therefore, MLG optical properties, like infrared emissivity and absorbance, can be controlled in a wide range by voltage bias. The large emissivity modulation achievable with this material makes it suitable in the design of thermal dynamic camouflage devices. Generally, the emissivity modulation in the multilayered graphene medium is governed by an intercalation process of non-volatile ionic liquids under a voltage bias. The electrically-driven reduction of emissivity leads to a decrease in the apparent temperature of the surface, which can match that of the background enabling thermal camouflaging. Since this property is common to other graphene-based materials, here we present a review specifically focused on the recent advances in the field of the thermal camouflage properties of graphene in the form of composite film and aerogel structures. A summary of the current understanding of the working principle of thermal camouflage materials, current limitations, and future opportunities is presented and discussed.

This study evaluates the efficiency of biodegradable polyurethane foams as thermal insulation materials compared to conventional materials like expanded polystyrene (EPS). Key parameters analyzed include thermal conductivity, energy savings, CO2 emission reductions, and investment payback periods. Biodegradable polyurethane foams demonstrated a thermal conductivity of 0.022 W/(m·K), significantly lower than EPS's 0.035 W/(m·K), leading to higher energy savings. Calculations reveal an annual energy saving of 443,820 kWh for polyurethane foams, compared to 441,330 kWh for EPS. Financially, polyurethane foams save approximately €53,258.4 annually, while EPS saves €52,959.6. In terms of environmental impact, polyurethane foams reduce CO2 emissions by 88,764 kg annually, versus 88,266 kg for EPS. Despite the higher initial cost of polyurethane foams (€50/m² compared to €30/m² for EPS), the payback period is remarkably short at 0.094 years (1.13 months) compared to EPS's 0.057 years (0.68 months). These findings highlight biodegradable polyurethane foams as a superior option for thermal insulation, offering significant energy, financial, and environmental benefits.

A Q-switched Nd:YAG laser was focused on Pb-Ti alloy samples in several Laser Induced Breakdown experiments in order to measure the Stark parameters of several spectral lines (58) of single ionized Titanium including the 3504.89 Å, and the 3510.83 Ålines (where we aported new experimental and theoretical values).Diagnostics of the laser induced plasmas (electron density and electron temperature) was performed using Balmer’s H alpha line (6562.7 Å).Temperatures were obtained by the Boltzmann Plot technique with spectral lines of Pb I (after correction for its evident self-absorption).Subsequently, calculations by the Griem approach of the Stark broadening parameters for several spectral lines were performed using the Gaunt factors proposed by Van Regemorter and those proposed by Douglas H. Sampson. In the latter cases the values obtained were very close to the experimental values. It allows us to assume that the calculations made for the spectral lines of Ti II, without experimental information, are more accurate using the Gaunt factors proposed by Sampson.

Surface initiated atom transfer radical polymerization (SI-ATRP) is one of the most versatile technique to modify the surface properties of material. Recent developed metal free SI-ATRP makes such technique more widely applicable. Herein photo-induced metal-free SI-ATRP of methacrylates, such as methyl methacrylate, N-isopropanyl acrylamide, and N,N- dimethylaminoethyl methacrylate, on the surface of SBA-15 was reported to fabricate organic-inorganic hybrid materials. SBA-15 based polymeric composite with adjustable graft ratio was obtained. The structure evolution during the SI-ATRP modification of SBA-15 was monitored and verified by FT-IR, XPS, TGA, BET, and TEM. The obtained polymeric composite showed enhanced adsorption ability for the model compound toluene in aqueous. This procedure provides a low cost, ready availability, and facile modification way to synthesize the polymeric composites without the contamination of metal.

The self-assembly is an intriguing process of great importance in general soft matter and thus re-ceives an ever-growing scientific interest. Its most trivial example is the entropy-driven crystalli-zation of hard spheres. Past works have established the similarities and differences in the phase behavior of monomers and chains made of hard spheres. In the present work, inspired by the dif-ference in the melting points of the pure components, we study, through Monte Carlo simulations, the phase behavior of athermal mixtures composed of fully flexible polymers and individual monomers of uniform size. We analyze how the relative number fraction and the packing density affect crystallization and the established ordered morphologies. A synergetic effect is observed in the crystallization leading to synchronous crystallization of the two species. Structural analysis of the resulting ordered morphologies shows perfect mixing and thus no phase separation, which could split the system into polymer-rich and monomer-rich domains. Due to the constraints imposed by chain connectivity, the local environment of the individual spheres is systematically more spherical and more symmetric compared to the one of spheres belonging to chains. In general, increasing polymer content leads to reduction of the degree of crystallinity. According to the present findings, relative concentration is another determining factor to control the phase behavior of hard colloidal systems based on polymers.

Particles are considered temporarily identical if the interchange of these particles does not cause any observable physical effects within a time interval Δt. An indistinguishability hypothesis is proposed for such particles, suggesting that two particles (or systems) with nearly the same degree of internal freedom will actually interchange under certain circumstances, thereby affecting the subsequent dynamics. This indistinguishability implies that, theoretically, it is possible to capture an elementary particle with extraordinarily large internal freedom by trading it for an isolated composite system of ordinary matter particles with almost the same total internal freedom as the large-freedom particle. Following this, the ordinary particles will instantly disperse into the environment, while the large-freedom particle will initially be captured and then gradually delocalized into the environment, an observable phenomenon. If this hypothesis is proven true in the future, it might provide a novel strategy for detecting dark matter particles.

Recently, polyacetylene (PA) is receiving a renewed scientific attention due to its electrical properties potentially useful for energy applications (e.g., fabrication of electrodes for batteries and supercapacitors) and unique functional characteristics (e.g., flame retardant, oxygen scavenger, EMI-shielding, etc.). This chemical compound can be obtained in form of a polyacetylene-PVOH copolymers simply by chemical dehydration of poly(vinyl alcohol) (PVOH), which is a very common type of polymer, widely used in packaging and other technological areas. This very inexpensive chemical reaction for the large-scale synthesis of PA/polyvinylenes has been investigated by reacting PVOH with fuming sulfuric acid at room temperature. In this process, PVOH, shaped in form of film, is dipped in fuming sulfuric acid (i.e., H₂SO₄ at 95-97%) and, after complete chemical-dehydration, it has been mechanically removed from the liquid phase by using a nylon sieve. The reduction process leads to a substantial PVOH film conversion to PA as it has been proved by infrared spectroscopy (ATR-mode). Indeed, the ATR spectrum of the reaction product included all characteristic absorption bands of PA. The reaction product has been also characterized by UV-Vis spectroscopy in order to evidence the presence in the structure of conjugated carbon-carbon double bonds of various lengths. Differential scanning calorimetry (DSC) and thermogravimetric analysis have been used respectively to investigate the PA solid-state cis-trans isomerization and thermal stability in air and nitrogen, respectively.

The review scrutinizes the currently performed research on the new methods for enhancing bituminous binder performance through radiation and radical grafting of polymer modifers of bitumen. It investigates innovative methods, including using waste polymers as modifiers, and applying radiation for polymer grafting, to overcome challenges like high costs, low aging resistance and storage stability issues, of which separation of phases polymer/bitumen is the most significant obstacle. These advanced modification techniques promise sustainability through the decrease of the carbon footprint of transportation systems by improving the properties and durability of binders. Additionally, the review discusses the parameters and mechanistic aspects from a scientific perspective, shedding light on the underlying processes that contribute to the improved performance of modified bituminous binders.

The ability of thermoresponsive polymers to respond to temperature with a reversible conformational change makes them promising ‘smart’ materials for solutions in medical and biotechnological applications. In this work, two such polymers and structural isomers were studied: poly(N-isopropyl acrylamide) (PNiPAm) and poly(2-isopropyl-2-oxazoline) (PiPOx). We compare the critical solution temperatures (CST) of these polymers in D2O and H2O in the presence of Hofmeister series salts, as results obtained under these different solvent conditions are often compared. D2O has a higher dipole moment and electronegativity than H2O, which could significantly alter the CST transition. We used two complementary methods to measure the CST, dynamic light scattering (DLS) and differential scanning calorimetry (DSC), and found that the CST decreased significantly in D2O compared to H2O. In the presence of highly concentrated kosmotropes, the CST of both polymers decreased in both solvents. The influence of the kosmotropic anions was smaller than the water isotope effect at low ionic strengths but considerably higher at physiological ionic strengths. However, the Hofmeister anion effect was quantitatively different in H2O than in D2O, with the largest relative differences observed for Cl-, where the CSTs in D2O decreased more than in H2O measured by DLS but less by DSC. PiPOx was more sensitive than PNiPAm to the presence of chaotropes. It exhibited much higher transition enthalpies and multistep transitions, especially in aqueous solutions. Our results highlight that measurements of thermoresponsive polymer properties in D2O cannot be compared directly or quantitatively to application conditions or even measurements performed in H2O.

The dielectric constant (ε) reflects the ability of a material to align and orient electrical dipoles within its structure in response to an externally applied electric field; the greater the polarizability of molecules, the greater the value of dielectric constant. In this study a data set of 86 polymers was investigated to develop a structure-property quantitative relations (QSPR) model to predict the dielectric constant in polymers. An initial set of 1273 descriptors was used to select a best set of descriptors and to construct two machine learning models with Gradient Boosting Regressor (GB_A and GB_B). The best performing model (GB_A) with 8 descriptors, exhibited a performance of (R2train) = 0.938 and (R2test) = 0.802. The models were internally validated by 5 folds cross-validation, demonstrating robustness. Additionally, using the Accumulative Local Effect (ALE) technique, we analyzed the relationship between the 8 descriptors involved and the impact of these descriptors to dielectric constant of polymers.

(1) Background: A wide literature based on loading and unloading bending tests has been carried out over the half past century for assessing the force released by superelastic wires. The aim of this investigation is not only to characterize a broadly described superelastic NiTi and a novel CuNiTi archwire, but also to provide novel insights into the load vs deflection profiles. A harmonic scenario for superelastic wires will be shown as temperature is kept constant at 37°C. However, a completely different picture will be highlighted as a temporary heating step up to 50°C is introduced within the force vs deflection profiles. (2) Methods: A variety of NiTi and a novel CuNiTi round and rectangular cross-section archwires have been investigated. Static 3-point bending tests up to a deflection level of 3.0 mm have been carried out for detecting the unloading force plateau levels occurring at 37°C. A hold deflection step of 5 min at deflection levels occurring along the unloading plateau extension is introduced. The effect of a temporary heating up to 50°C on the force plateau level released by the investigated wires is analyzed. (3) Results: Mechanical profiles suggest that the plateau force levels detected at 37°C are consistent with those broadly reported in the literature, but they only represent a single block puzzle of the force scenario that a superelastic wire releases during the orthodontic treatment. (4) Conclusions: Once a superelastic wire is bent and clinically applied, the effect of a temporary heating up to 50°C (e.g. hot food or drink ingestion) produces a significant plateau force increase whose magnitude depends on the deflection level. The highest force increase of about 50% and 40% have been detected at deflection levels located at the beginning of the unloading plateau extension for NiTi and CuNiTi wires, respectively.

In this study, the coating order of two monomers in the shell polymerization process of core–shell nanoparticles was altered to facilitate easy coating and optimize the properties of the coated surface to simplify the additional coating formulation process. To obtain a glass transition temperature suitable for coating, a core was synthesized by the copolymerization of an acryl monomer. A perfluoro monomer and silane monomer were additionally added to synthesize nanoparticles exhibiting both water–oil repellency and anchoring properties. In order to realize various surface properties, the nanoparticles underwent surface modification and cellulose fiber was introduced. Through the various data described in this text, the surface properties improved with the order of introduction of the two monomers.

The release of the active substance from the matrix modified-release tablets based on Kollidon®SR and chitosan depends on its solubility in the dissolution medium and on the composition of the matrix-forming polymers. The study is based on new oral matrix tablets based on Kollidon®SR and chitosan, formulated to optimize the low oral bioavailability of chlorzoxazone, a non-steroidal anti-inflammatory drug, a class II Biopharmaceutical Classification System. Nine types of chlorzoxazone matrix tablets were obtained using the direct compression method, and their combination at 1:1, 1:2, 1:3 chlorzoxazone/ excipients, 20%-40% (w/w) Kollidon®SR, 3-7% (w/w) chitosan and the auxiliary substances were formulated in constant concentrations. Pharmaco-technical characterization included the analysis of flowability and compressibility properties (flow time, friction coefficient, angle of repose, Hausner ratio, Carr Index), and of pharmaco-chemical characteristics (mass and dose uniformity, thickness, diameter, mechanical strength, Friability, degree of softening, in vitro release profile) of the tablets. Based on the initial evaluation of the pharmaco-technical analysis, pharmaco-chemical characteristics, and in vitro release profile, only three matrix tablet formulations (F1b, F2b, and F3b) were further tested. They were evaluated through Fourier-transform infrared spectrometry, X-ray Diffraction, thermogravimetry, differential scanning calorimetry, and in vitro dissolution tests. The three formulations were comparatively studied regarding the release kinetics of active substances using in vitro release testing. The results were analyzed by fitting into four representative mathematical models for the modified release oral formulations. In vitro kinetic study reveals a complex mechanism of release occurring in the first (0 - 2 hours) and second (2.0 hours – 36 hours) steps of drug release. Two factors have been calculated to assess the release profile of chlorzoxazone: f1 - the similarity factor and f2 - the factor difference. The results have shown that both Kollidon®SR and chitosan may be used as matrix-forming agents when combined with chlorzoxazone. In vitro dissolution tests revealed the F2b sample, data suggesting a faster drug release. The three formulations showed optimum pharmaco-technical properties and in vitro kinetic study, and they had tremendous potential to be used in oral pharmaceutical products for the controlled delivery of chlorzoxazone.

Background: Complex bone defects are challenging to treat. Autografting is the gold standard for regenerating bone defects, however limitations include donor site morbidity and increased surgical complexity. Advancements in 3D bioprinting (3DBP) offer a promising alternative for viable bone grafts. Methods: Design of Experiments (DoE) was used to design 12 hydrogel bioinks of various Gelatin meth-acrylate/hydroxyapatite (GelMA/HA) concentrations. These bioinks were assessed for pipettability and equilibrium modulus. An optimal bioink was designed using the DoE data to produce the greatest stiffness while still being pipettable. Two bioinks, the DoE designed maximal stiff-ness and the experimentally defined maximal stiffness vs. a literature based control were then printed using a 3D bioprinter and assessed for print fidelity. The resulting hydrogels were combined with human bone-marrow-derived mesenchymal stromal cells (hMSCs) and evaluated for cell viability. Results: DoE ANOVA analysis indicated that the augmented 3 level factorial design model used was a good fit (p < 0.0001). Using the model, DoE correctly predicted that a composite hydrogel consisting of 12.3% GelMA, 15.7% HA, and 2% Gelatin would produce the maximum equilibrium modulus while still being pipettable. The hydrogel with the most optimal print fidelity was 10% GelMA, 2% HA, and 5% Gelatin. There were no significant differences in cell viability within hydrogels from day 2 to day 7 (p > 0.05). There was however a significantly lower cell viability in the gel composed of 12.3% GelMA, 15.7% HA, and 2% gelatin compared to the other gels with lower HA concentration (p < 0.05), showing that higher HA or print pressure may be cytotoxic within hydrogels. Conclusions: Extrusion-based 3DBP offers significant advantages for bone-tissue implants due to its high customizability. This study demonstrates it is possible to create printable bone-like grafts from GelMA and HA with increased HA levels, favorable mechanical properties (145kPa) and >80% cell viability.

The capacity of 3D printing (3DP) technologies to initiate speedy polymerization of solvent free resins accounts for their utility in the manufacturing of medical devices. Nonetheless, independent biological evaluation of 3D printed materials is recommended due to the unique parameters of the manufacturing process, which can influence their physical, chemical, and biological properties. In this study, E-Shell 450 material indicated for 3DP of hearing aid shells and inner ear devices was examined for biological safety using zebrafish bioassays adapted to OECD fish embryo test. In addition, the proprietary material was characterized for composition using headspace gas-chromatography mass spectrometry (GC-MS). To initiate test, newly fertilized zebrafish eggs were cultured on non-treated and ethanol-treated materials in glass petri dishes with ultrapure water, incubated at 28.5°C and assessed for developmental endpoints of toxicity at 24h interval until 96h. Data confirmed non-treated material was extremely toxic in bioassays within 24h whereas ethanol-treated material showed a relative lower toxicity possibly due to ethanoic-aqueous interactions as observed by GC-MS. With the current influx of 3D printing materials, users are urged to exercise caution. Operators must also take cognizance of the potential toxicity of the chemicals used in 3DP and implement safety measures to limit their exposure.

For the past few decades, researchers have been intrigued with glassy polymers, which have applications ranging from gas separations to corrosion protection to drug delivery systems. The techniques employed to examine the sorption and diffusion of small molecules in glassy polymers are the subject of this review. Diffusion models in glassy polymers are regulated by Fickian and non-Fickian diffusion, with non-Fickian diffusion being more prevalent. The characteristics of glassy polymers are determined by sorption isotherms, and different models have been proposed in the literature to explain sorption in glassy polymers during the last few years. This review also includes the applications of glassy polymer. Despite having so many applications, current researchers still have difficulty in implementing coating challenges due to issues like as physical ageing, which is briefly discussed in the review.

A study was conducted to predict failure stresses, failure locations, and their paths of initiation of perforated polymethyl methacrylate (PMMA) specimens as they were loaded using pins inserted into the holes. First, a series of experiments were conducted for perforated PMMA coupons. There were six different types of coupons. The test specimens had three different widths with a circular hole of a diameter of 8 mm, which was placed at two different locations along the specimen length. All the specimens were loaded using a pin inserted into the hole with three different pins of nominal diameters of 8 mm, 6 mm, and 5 mm, respectively. To predict the failure and compare the results against the experimental data, the recently proposed universal failure criterion was used in the study using finite element analyses. The failure criteria gave acceptable results as compared to the experimental data.

The interest in obtaining new composite materials with diverse properties has created a growing interest in natural fi-bers as reinforcement in polymers, which has generated an impact in sectors such as automotive and construction, dis-placing synthetic fibers. Properties such as low density, low cost, and rene.wable make these fibers an attractive alterna-tive to reduce environmental impact. Their application in polymers, such as polypropylene, polyethylene, and epoxy resins, has allowed the modification of polymeric composite materials' mechanical and physical properties (NFRP). This review focuses on investigating the status of natural fiber-reinforced polymers. It analyzes their worldwide demand, chemical characteristics, physical and mechanical properties, and various applications in different sectors and indus-tries. In addition, the advantages and disadvantages of NFRPs are highlighted, highlighting their potential for new ap-plications.

Two-dimensional layered coordination polymers based on the hetero-substituted 3-chloro-6-cyano-2,5-dihydroxybenzoquinone ligand, hereafter ClCNAn2- anilate, and LnIII ions (Tb and Eu) are reported. Compounds 1, 2, formulated as Ln2(ClCNAn)3(DMSO)6 (LnIII = Tb, 1; Eu, 2) and their related intermediates 1’ and 2’, formulated as Ln2(ClCNAn)3(H2O)x.yH2O (x+y likely = 12, Ln = Tb, 1’; and Eu, 2’) were prepared by a conventional one-pot reaction (the latter) and recrystallized from DMSO solvent (the former). Polyhydrated intermediates 1’ and 2’ show very similar XRPD patterns, while, despite their common stoichiometry, 1 and 2 are not isostructural. 1 consists of a 2D coordination framework of 3,6 topology, where [Tb(DMSO)3]3+ moieties are bridged by three bis-chelating ClCNAn2- ligands, forming distorted hexagons. Ultrathin nanosheets of 1 were obtained by exfoliation, via liquid assisted sonication method and characterized by atomic force microscopy, confirming the 2D nature of 1. The crystal structure of 2, still showing the presence of 2D sheets with “hexagonal” mesh and a common (3,6) connectivity, is based onto flat, non-corrugated slabs. Indeed, at a larger scale, the different “rectangular tiles” show a clear roofing in 1, which is totally absent in 2. The magnetic behavior of 1 very likely indicates depopulation of the highest crystal-field levels, as expected for TbIII compounds.

Inverse gas chromatography at infinite dilution was used to determine the surface thermodynamic properties of silica particles and PMMA adsorbed on silica, and more particularly, to quantify the London dispersive energy γsd, the Lewis acid γs+ and base γs- polar surface energies of PMMA/silica composites as a function of the temperature and the recovery fraction θ of PMMA. The polar acid–base surface energy γsAB and the total surface energy of the different composites were then deduced as a function of the temperature. In this paper, the Hamieh thermal model was used to quantify the surface thermodynamic energy of poly methyl methacrylate (PMMA) adsorbed on silica particles at different recovery fractions. A comparison of the new results was carried out with those obtained by applying other molecular models of the surface areas of organic molecules adsorbed on the different solid substrates. An important deviation of these molecular models from the thermal model was proved. The determination of γsd, γs+, γs-, and γsAB of PMMA in both bulk and adsorbed phases showed an important non-linearity variation of these surface parameters as a function of the temperature. The presence of maxima in the curves of γsd(T) highlighted the second order transition temperatures in PMMA showing beta-relaxation, glass transition and liquid-liquid temperatures. These three transition temperatures depended on the adsorption rate of PMMA on silica. The proposed method gave a new relation between the recovery fraction of PMMA and its London dispersive energy showing an important effect of the temperature on the surface energy parameters of adsorption of PMMA on silica. A universal equation relating γsd(T,θ) of the systems PMMA/silica to the recovery fraction and the temperature was proposed.

This research was devoted to study the effect of the tacticity of PMMA on the surface physicochemical properties such as the London dispersive component of the surface energy of the polymer, the polar and dispersive free energies, the Lewis’s acid-base surface parameters, and the Lewis acid and base surface energies of atactic, isotactic and syndiotactic PMMAs as a function of the temperature. Inverse gas chromatography (IGC) at infinite dilution was used to determine the surface thermodynamic properties of PMMA at different tacticities. The experimental values of the net retention time and volume of model organic molecules adsorbed on the atactic, isotactic and syndiotactic PMMAs, were obtained by IGC technique at infinite dilution. The London dispersion interaction energy was used for the separation of the polar and dispersive energy of the different n-alkanes and polar solvents adsorbed on the different PMMA surfaces. The London dispersive surface energy γ_s^d (T) of PMMAs was determined by applying the Hamieh thermal model that took into account the effect of the temperature on the surface area of adsorbed molecules. The obtained results showed non-linear variations of γ_s^d (T) of atactic, isotactic, and syndiotactic PMMAs with three maxima characterizing the three transition temperatures of PMMAs, T_g, T_g and T_(liq-liq) with a shift of these temperatures with the isotactic and syndiotactic PMMAs. It was showed that the polar interaction free energy ∆G_a^p (T) also showed the presence of the three above transition temperatures of the polymers. The study showed an important non-linearity variation of the different acid-base parameters in the various polymer surfaces proving the highest effect of the temperature and the tacticity on these parameters. The determination of the enthalpic and entropic Lewis’s acid-base parameters showed an amphoteric character for the different PMMAs. The basicity of the atactic PMMA was about four times larger than its acidity outside the neighborhood of the transition temperatures of the polymer. Whereas, the isotactic PMMA was about 2 to 2.5 times more basic than acid, while the syndiotactic PMMA exhibited the highest basicity by showing a surface 5 to 8 times more basic than acid. However, the Lewis acid-base parameters strongly depended on the temperature and sudden variations of these surface parameters were observed around the transition temperatures largely depending on the PMMA tacticity. The determination of the polar acid and base surface energies of the three PMMAs led to the same previous transition temperatures with an important effect of the tacticity of PMMA on the values of these acid-base surface energies.

In the construction sector, the integration of biobased materials has emerged as a pivotal aspect of EU policies, aimed at promoting sustainable practices throughout the value chain to mitigate resource consumption and carbon emissions. This paper explores the development and validation activities of a bio-based façade system within the Basajaun H2020 project, focusing on enhancing the utilization of biobased components within building envelopes to replace conventional solutions with eco-friendly alternatives. This paper reports the methodologies employed to detect requirements and outline the testing protocols undertaken to validate the façade system design devised within the project focusing on the original façade components as the bio composite profile. Vision and opaque façade modules are prototyped and tested following curtain wall standards standard for performance and acoustic assessments, to showcase the efficacy of the developed solution. The conducted tests demonstrate the feasibility of integrating bio-based components into building envelopes, aligning with project expectations, and prevailing standards for curtain wall façade solutions. Notably, the designed façade system meets technical conditions and project objectives. Nevertheless, the research underscores the need for further refinements to facilitate solution industrialization and explore broader market applicability. Future efforts will focus on addressing these improvements and assessing the scalability of the solution.

In this work, the properties of a composition based on synthetic rubber ethylene-propylene ter-polymer and polymers with functional groups of the mixture are studied. Low efficiency of some compositions based on ethylene and propylene copolymer limits their use in the production of tires and rubber products. Therefore, we conducted a study to improve the disadvantages of SREPT-60 using butyl rubber + choro polyisoprene + butadiene-nitrile + butadiene styrene rubber and adding a plasticizer to the composition = α, methacrylate-(bis-diethylene glycol phthalate) -(btegf-9) The data obtained showed that a number of its indicators of rubber based on them were improved. Tear resistance, resistance to repeated stretching increased, adhesion of the composition to metal, chemical resistance increased, the degree of swelling in benzene and gasoline-benzene mixture decreased. Compositions based on the mixture SREPT-60 using butyl rubber + choro polyisoprene + butadiene-nitrile + butadiene styrene rubber and adding a plasticizer to the composition = α, methacrylate-(bis-diethylene glycol phthalate) -(btegf-9) +Dioctyl phthalate: (70:20:10) have high resistance to swelling in an aggressive environment (Benzene, gasoline, alcohol, acid, oil, etc.) mixture.

The capability of radially polymerized bio-dendrimers and hyperbranched polymers for medical applications is well established. Among them, perhaps the most important are those that involve interactions with the regenerative mechanisms of cells. Dendritic polymers due to their distinctive architecture may play a multitude of roles such as protein biomimicry (collagen, elastin, hydroxy apatite production), gene and drug delivery (cell differentiation, antimicrobial protection), surface chemistry and charge modulation (adhesion to cells and tissues), polymer cross-linking (eye, skin and internal organ wound healing). The review highlights all the different categories of hard and soft tissues that may be remediated with their contribution. The reader will be also exposed to the incorporation methods to established biomaterials such as scaffolds, the functionalization strategies, and the synthetic paths for the assembly from biocompatible building blocks and natural metabolites.

Silicon (Si) is the major material of semiconductor element. For semiconductor element producing, Si need to refined into high-purity silicon crystals, which has the approximate characteristics of intrinsic semiconductor, then doping 13th group or 15th group trace element. Producing the high-purity silicon crystals with well-lattice structure need a lot of energy and highly cost. Besides, the high-purity silicon is very hard and fragile which limits the scope of application. For this reason, this study added low-grade non-complete lattice silicon in the elastic polymer, and then doped with high concentrations of fine carbon powder. This material can be conductive by physisorption;therefore, it can be used to making semiconductors. Using this material to produce electronic components can significantly reduce the cost of purification and crystallization, saving energy at the same time. Moreover, because this elastic polymer materials containing silicon, which has soft, warm, and durable physical properties. With those properties, the design of the device could be more flex, full scalability and close to the skin.

We present results on the spontaneous crystallization of freely-jointed polymers of hard spheres obtained in an unprecedentedly long Monte Carlo (MC) simulation on a system of 54 chains of 1000 monomers. Starting from a purely amorphous configuration and after a transitory dominance of the hexagonal closed packed (HCP) polymorph, the system crystallizes in a final, stable, face centered cubic (FCC) crystal of very high perfection. Through refined metrics we gauge the degree of ordering and identify the regions of the phase transition and the corresponding morphologies. An analysis of chain conformational characteristics, of the spatial distribution of monomers and of the volume accessible to them shows that the phase transition is caused by an increase in translational entropy that is larger than the loss of conformational entropy of the chains in the crystal compared to the amorphous state. Polymer chains in the crystal adopt ideal random walk statistics as their great length renders local conformational details, imposed by the geometry of the FCC crystal, irrelevant.

Flexibility of polymers defined by an equation in 2019 is related here to thermal conductivity, using reliable data for both properties found in the literature. The resulting equation is simple, it has the form of a quadratic polynomial. The goodness of the fit represented by R² = 0.975, while R² = 1 represents a perfect fit. Thus, knowledge of one of these properties can be used for calculation of the other one. The present results are a part of a larger program enabling obtaining by calculation pertinent properties of polymers from other properties for which data are available.

The effective treatment for chronic wounds constitute one of the most common worldwide health care problem due to the presence of high levels of proteases, free radicals and exudates in the wound, which constantly activate the inflammatory system avoiding the tissue regeneration. In this study, we describe a multifunctional bioactive and resorbable membrane with in-built antioxidant agent for the continuous quenching of free radicals as well as to control inflammatory response helping to promote the wound healing process. To reach that goal synthesized statistical copolymers of N-vinylcaprolactam (V) and 2-hydroxyethyl methacrylate (H) have been conjugated with catechol bearing hydrocaffeic acid (HCA) molecules. The natural polyphenol (catechol) is the key molecule responsible for the mechanism of adhesion of mussels, and provides the functionalized polymer conjugate a continuous antioxidant response, antiinflammatory effect, UV screen and bioadhesion in the moist environment of the human body, all of them key features in the wound healing process. Therefore, these novel mussel-inspired materials have an enormous potential of application and can act very positively, favoring and promoting the healing effect in chronic wounds.

This review is focused on current state-of-the-art research on electroactive-based materials and their synthesis, as well as their physicochemical and biological properties. Special attention is paid to pristine intrinsically conducting polymers (ICPs) and their composites with other organic and inorganic components, well-defined micro- and nanostructures, and enhanced surface areas compared with those of conventionally prepared ICPs. Hydrogels, due to their defined porous structures and being filled with aqueous solution, offer the ability to increase the amount of immobilized chemical, biological or biochemical molecules. When other components are incorporated into ICPs, the materials form composites; in this particular case, they form conductive composites. The design and synthesis of conductive composites result in the inheritance of the advantages of each component and offer new features because of the synergistic effects between the components. The resulting structures of ICPs, conducting polymer hydrogels and their composites, as well as the unusual physicochemical properties, biocompatibility and multi-functionality of these materials, facilitate their bioapplications. The synergistic effects between constituents have made these materials particularly attractive as sensing elements for biological agents, and they also enable the immobilization of bioreceptors such as enzymes, antigen–antibodies, and nucleic acids onto their surfaces for the detection of an array of biological agents. Currently, these materials have unlimited applicability in biomedicine. In this review, we have limited discussion to three areas in which it seems that the use of ICPs and materials, including their different forms, are particularly interesting, namely, biosensors, delivery of drugs and tissue engineering.

The contribution aims to bring forth a novel synthesis route in developing transparent UV-LED curable coatings accounting various exposure options. A selection of perfluoropolyether (PFPE)-urethane methacrylate and acrylate resins, free-radical photo-initiator Omnirad 2100, and two distinct silane based crosslinking agents were blended under a weight ratio of 75:20:5 (without crosslinker) and 70:15:5:10, respectively. The coatings were cured under a UV-LED 4 x 3 matrix light emitting source, in a chamber under controlled atmosphere, by means of an in-house developed conveyor belt type platform, at different conveyor belt speed (5, 50, 150, 250, and 500 mm/s). The morphologies of fabricated coatings were characterized by FTIR revealing high conversion rates (e.g., from 98 to 100%) for increased exposure time as resulted from the 5 or 50 mm/s values, on all combinations. Dynamic-mechanical and optical properties of UV-LED cured transparent coatings were also investigated. A negative shift of a glass transition temperature values with a decrease in exposure time, in all combinations, from about 60 °C to 30 °C, along with storage moduli lowering in the glassy plateau further favor on higher exposure times for curing. The refractive indices of polymers were from 1.38 to 1.40, whereas the thermo-optic coefficients are showing minor changes around value of 2.55∙10-4 K-1.

Reaction of 2-mercapto-3-phenylquinazolin-4(3H)-one (MPQ) with both 4-vinyl benzyl chloride and allyl bromide furnished the reactive heterocyclic monomers 3-phenyl-2-((4-vinylbenzyl) thio) quinazolin-4(3H)-one (PVTQ) and 2-(allylthio)-3-phenylquinazolin-4(3H)-one (APQ), respectively. Copolymerization of PVTQ monomer with styrene and methyl methacrylate in the presence of 2,2′-azobisisobutyronitrile (AIBN) afforded the copolymers PS-co-PPVTQ and PMMA-co-PPVTQ, respectively. Similarly, copolymerization of monomer APQ with styrene and methyl methacrylate (MMA) afforded the copolymers PS-co-PAPQ and PMMA-co-PAPQ, respectively. The resulted copolymers were characterized by using FT-IR, 1H-NMR and GPC techniques. Silver nanocomposites of PS, PMMA, PS-co-PPVTQ, PMMA-co-PPVTQ, PS-co-PAPQ and PMMA-co-PAPQ were synthesized by the addition of silver nitrate into the polymer solution. The reduction of silver ions into silver nanoparticles was performed in DMF and water. Thermogravimetric (TGA) analysis was used to determine the thermal stability of the copolymers and their silver nanocomposites. The X-ray diffraction (XRD) analysis indicated the amorphous structures of the co-polymers and confirmed the formation of silver nanoparticles. The antitumor and antibacterial activities were screened for the copolymers and enhanced by the formation of their silver nanocomposites. In vivo antitumor activity in Ehrlich Ascitic Carcinoma (EAC) mice model showed that PS-co-PPVTQ/Ag NPs, PMMA-co-PPVTQ/Ag NPs, and PMMA-co-PAPQ/Ag NPs displayed promising inhibitory effects against EAC and induce apoptosis against MCF-7 cells.

Polymethyl methacrylate (PMMA) is a transparent thermoplastic with excellent optical properties, transparent surface, low moisture absorption, tensile and electrical resistance. In this study, the alloy was prepared through PMMA and cycloolefin copolymer (COC) due to some similar properties. The mechanical test showed that properties such as impact resistance, elongation, tensile, and flexural strength decreased by adding COC by up to 20% due to less incompatibility and miscibility, but mentioned properties improved by adding COC 40% due to sub-phase generation. The DSC and DMTA tests showed improvement in the thermal properties of alloys by adding 40% COC. SEM micrographs exhibited a softer surface and more phase elongation of the alloy. Finally, the sample was selected as the optimal sample in terms of mechanical properties irradiated by electron beam, and amplification results showed that a dose of 50 KGY increased the mechanical and thermal properties relatively.

A novel scaffold design has been created to enhance tissue engineering and regenerative medicine by optimizing the controlled, prolonged release of hepatocyte growth factor (HGF), a powerful chemoattractant for endogenous mesenchymal stem cells. We present a new stacked scaffold that is made up of three different fibrin gel layers, each of which has HGF integrated into the matrix. The design attempts to preserve HGF's regenerative properties for long periods of time, which is necessary for complex tissue regeneration. These multi-layered fibrin gels have been mechanically evaluated using rheometry, and their degradation behavior has been studied using D-Dimer ELISA. Understanding the kinetics of HGF release from this novel scaffold configuration is essential for understanding HGF's long-term sustained bioactivity. A range of cell-based tests were carried out to verify the functionality of HGF following extended incorporation. These tests included 2-photon microscopy using phalloidin staining to examine cellular morphology, SEM analysis for scaffold-cell interactions, and scratch and scatter assays to assess migration and motility. The analyses show that the novel stacking scaffold promotes vital cellular processes for tissue regeneration in addition to supporting HGF's bioactivity. This scaffold design was developed for in situ tissue engineering. Using the body as a bioreactor, the scaffold should recruit mesenchymal stem cells from their niche thus combining the regenerative abilities of HGF and MSCs to promote tissue remodeling and wound repair.

This study focuses on enhancing controllable fibrin-based hydrogels for tissue engineering, addressing existing weaknesses. By integrating a novel copolymer, we improve the foundation for cell-based angiogenesis with adaptable structural features. Tissue engineering often faces challenges like waste disposal and nutrient supply beyond the 200 µm diffusion limit. Angiogenesis breaks through this limitation, allowing the construction of larger constructs. Our innovative scaffold combination significantly boosts angiogenesis, resulting in longer branches and more capillary network junctions. The copolymer attached to fibrin fibers enables precise adjustment of hydrogel mechanical-dynamic properties for specific applications. Our material proves effective for angiogenesis, even under suppression factors like suramin. In our study, we prepared fibrin-based hydrogels with and without the copolymer PVP12400-co-GMA10mol%. Using a co-culture system of human umbilical vein endothelial cells (HUVEC) and mesenchymal stem cells (MSC), we analyzed angiogenetic behavior on and within the modified hydrogels. Capillary-like structures were reproducibly formed on different surfaces, demonstrating the general feasibility of three-dimensional endothelial cell networks in fibrin-based hydrogels. This highlights the biomaterial's suitability for in vitro pre-vascularization of biohybrid implants.

Shell nacre from Pinctada species has been extensively researched for managing bone defects. However, there is a gap in the research on using shell nacre as cement with improved physico-chemical properties. To address this, the current study aimed to develop a chemical curable com-posite shell nacre cement (SNC) using shell nacre powder and an organically modified ceramic resin shell nacre containing ladder-structured siloxane methacrylate (SNLSM). Different amounts of shell nacre (24, 48, and 72 weight(wt)%) were added to the SNLSM resin matrix and the effect on the physicochemical properties of the cement was studied. The composite shell nacre cement SNC 72 containing 72 wt% shell nacre exhibited significantly higher mechanical properties (com-pressive strength >100 MPa, flexural strength > 35 MPa) and low linear polymerization shrinkage (0.4%) than other compositions. SNC 72 was radiopaque and the exotherm generated during the curing of the cement was minimal. Direct contact of cured SNC 72 with L929 cells revealed the non-cytotoxic nature of the cement. Overall, the results of the study proved that the composite SNC 72 would be a promising candidate for bone defect management.

Biofilms play a crucial role in the development of Candida-associated denture stomatitis. Inhibition of microbial adhesion to PMMA and phosphate containing PMMA has been examined in this work. C. albicans and mixed salivary microbial biofilms were compared on naked and salivary pre-conditioned PMMA surfaces in the presence or absence of antimicrobials (cetyl pyridinium chloride [CPC], KSL-W, histatin 5 [his 5]). Polymers with varying amounts of phosphate (0-25%) were tested using four C. albicans oral isolates as well as mixed salivary bacteria and 24 h biofilms were assessed for metabolic activity and confirmed using Live/Dead staining and confocal microscopy. Biofilm metabolism was reduced as phosphate density increased (15%: P=0.004; 25%: P=0.001). Loading of CPC on 15% phosphated disks showed a substantial decrease (P=0.001) in biofilm metabolism in the presence or absence of a salivary pellicle. Salivary pellicle on uncharged PMMA enhanced the antimicrobial activity of CPC only. CPC also demonstrated remarkable antimicrobial activity on mixed salivary bacterial biofilms under different conditions displaying the potent efficacy of CPC (350 µg/ml) when combined with an artificial protein pellicle (Biotene half strength).

In this investigation, polymethyl methacrylate (PMMA) was mixed with cyclic olefin copolymer (COC) because of its hardness, strength, and transparency properties. The results of thermal analysis through TGA and DTG showed that the thermal properties of the alloy are improved using 40% cyclic olefin copolymer. Kinetics of thermal degradation (pyrolysis) of polymers have been studied and analyzed and thermal pyrolysis of polymethyl methacrylate and cyclic olefin copolymer thermoplastic polymer was conducted. The computation of kinetic analysis is measured along with the different methods used to study the kinetics. The activation energy (E) of degradation of studied materials was estimated using Ozawa Flynn and Wall (OFW), Starink and Kissinger’s methods, and evaluation of three kinetic parameters taken appropriate kinetic model in terms of percent change for both types of polymers have been proposed, and finally, simulated curves were compared with the experimental curves. Both mechanisms of degradation for COC and PMMA under nitrogen atmosphere will reflect intramolecular transfer and random scission of the main chain.

(1) Background: The aim of this investigation is to determine the effect of archwires’ deflection on the temperature transitions driving the austenite to martensite transformation (and vice versa) and the force released by NiTi and CuNiTi orthodontic wires. (2) Methods: Round cross-section archwires have been investigated. The calorimetric approach has been used for measuring transition temperatures occurring in the unstressed (e.g. undeflected) state of the wires. Static Thermo-mechanical analysis in a temperature controlled wet environment has been performed in the range of temperature between 5°C and 55°C for measuring temperature transitions occurring in highly deflected archwires in conjunction with the force released by these wires. (3) Results: Plateau forces investigated in Part I and those reported in the literature describes the wire’s behaviour only at deflection levels close to the end point of the force plateau extension detected at 37°C. Upon heating or cooling, the austenite finish (Af) transition temperature and the martensite start (Ms) temperature largely depends on the deflection level for both NiTi and CuNiTi. (4) Conclusions: The plateau force levels at 37°C, broadly reported in the literature, only represent the lower boundary force that a superelastic wire releases at 37°C above its elastic limit. For both NiTi and CuNiTi, plateau force levels at 37°C can be predicted by the static TMA profile matching the end point of the force plateau extension. Transition temperatures in largely deflected wires are significantly higher than those determined through the calorimetric approach.

Developing nanomaterials with the capacity to restrict the growth of bacteria and fungus is of current interest. In this study, nanocomposites of poly(2-hydroxyethyl methacrylate) (PHEMA) and carbon nanotubes (CNTs) functionalized with primary amine, hydroxyl, and carboxyl groups were prepared, and characterized. An analysis by Fourier transform infrared (FT-IR) spectroscopy and X-ray photoelectron spectroscopy showed that PHEMA chains were grafted to the functionalized CNTs. The morphology of the prepared nanocomposites studied by field emission scanning electron microscopy (FE-SEM), and transmission electron microscopy (TEM) shows significant changes with respect to the observed for pure PHEMA. The thermal behavior of the nanocomposites studied by differential scanning calorimetry (DSC) revels that the functionalized CNTs affects strongly the mobility of the PHEMA chains. Tests carried out by thermogravimetric analysis (TGA) were used to calculate the degree of grafting of the PHEMA chains. The ability of prepared nanocomposites to inhibit the growth of the fungus Candida albicans, and the bacteria Staphylococcus aureus, Pseudomonas aeruginosa, Escherichia coli was evaluated. A moderated antifungal and antibacterial capacity of the prepared nanocomposites was determined.

A time-sequential working, spatially multiplexed autostereoscopic 3D display design consisting of a fast switchable RGB-color filter array is presented. The wavelength-selective filter barrier emits the light from a display over a larger active area than common autostereoscopic barrier displays. An optical modelling of wavelength-selective barriers has been used for instance to calculate the light ray distribution properties of that arrangement. To find well working display designs, automated searches by simulation and computational evaluation has been proceeded. Wavelength-selective filter barrier arrangements exhibit characteristics different from common barrier displays with similar barrier pitch and ascent. In particular, these constructions show strong angular luminance dependency under barrier inclination specified by correspondent slant angle. In time-sequential implementation it is important to avoid that quick eye or eyelid movement lead to visible color artifacts. In the millisecond regime tunable liquid crystal Fabry-Pérot color filters for the colors red, green and blue are presented. They consist of a sub-micrometer thick nematic layer sandwiched between dielectric mirrors and ITO-electrodes. These cells shall switch narrow-banding light of red, green or blue. An array for a glasses-free 3D display has to be equipped with several thousand switchable filter elements having different color apertures. The newly introduced design is usable as a multi user display as well as a single user system with user adaptive control.

The aim of this study was to synthesize and characterize a novel Methacrylate- functionalized Calcium Phosphate (MCP) used as a bioactive compound for innovative dental composites. The characterization was accomplished by Attenuated Total Reflectance Fourier-Transform Infrared Spectroscopy (ATR-FTIR), X-Ray Diffraction Analysis (XRDA), Scanning Electron Microscopy (SEM), and EnergyDispersive Spectroscopy (EDS). The incorporation of MCP as a bioactive filler in esthetic dental composite formulations and the ability of MCP containing dental composites to promote precipitation of hydroxyapatite (HAp) on the surfaces of those dental composites was explored. The translucency parameter, depth of cure, degree of conversion, ion release profile, and other physical properties of composites were studied with respect to the amount of MCP added to the composites. Composites containing 3 Wt.%, 6 Wt.%, and 20 Wt.% MCP were evaluated at 7, 14, and 21 days. The progress of surface precipitation of hydroxyapatite on MCP-containing dental composites was studied by systematically increasing the MCP content in the composite and the time of specimen storage in Dulbecco’s phosphate-buffered solution with calcium and magnesium. It was found that there was a direct correlation between the percentage of MCP in a composite formulation, the amount of time the specimen was stored in PBS, and the deposition of hydroxyapatite on the composite’s surface

Molecularly imprinted polymers (MIPs) have been widely used in nanomedicine during the last few years. However, their potential is limited by their intrinsic properties resulting, for instance, in lack of control in drug release processes or complex detection for in vivo imaging. Recent attempts in creating hybrid nanomaterials combining MIPs with inorganic nanomaterials succeeded in providing a wide range of new interesting properties suitable for nanomedicine. Through this review, we aim to illustrate how hybrids molecularly imprinted polymers may improve patient care with enhanced imaging, treatments and combination of both.

A method for measuring the mechanical parameters of viscoelastic polymers by nanoindentation technology was proposed and verified. Through the mechanical response of load-displacement curves at different loading rates, then creep compliances and relaxation modulus were fitted. Polyimide thin film was employed in this research and experiments for five different loading rates were conducted. The fitting load-displacement loading curves obtained by the inversion method were identical to the experimental curves at five different loading rates，confirming the validity of the method. Moreover, with the loading rates increased，the fitting curves were more consistent commensurately with the nanoindentation experiment. DMA experiments were tested, and the generalized Kelvin/ Maxwell model were used for fitting experiment data. Results from DMA tests generally agree well with data from nanoindentation method, thereby verifying the feasibility of the method. The Prony series obtained by the two methods were used to simulate the creep experiments, which further verified the method.

Ocular drug delivery is one of the most challenging administration routes due to the very low drug bioavailability. In this work, we produce and characterize mucoadhesive mixed polymeric micelles (PMs) made of chitosan and poly(vinyl alcohol) backbones graft-hydrophobized with short poly(methyl methacrylate) blocks and use them to encapsulate cannabidiol (CBD), an anti-inflammatory cannabinoid. CBD-loaded mixed PMs are physically stabilized by ionotropic crosslinking of the CS domains with sodium tripolyphoshate and spray-drying. These mixed PMs display CBD loading capacity of 20% w/w and sizes of 100-200 nm, and spherical morphology (cryogenic-transmission electron microscopy). The good compatibility of the unloaded and CBD-loaded PMs is assessed in a human corneal epithelial cell line. Then, we confirm the permeability of CBD-free PMs and nanoencapsulated CBD in cornea cell monolayers under liquid-liquid and air-liquid conditions. Overall, our results highlight the potential of these polymeric nanocarriers for ocular drug delivery.

This review summarizes the most recent developments of research on protozoan parasite infections ac-quired through food and drinking water and is aimed at gathering updated knowledge on the risk factors, illnesses caused, and measures for prevention. Reports included dated from 2019 to the present and regarded recent outbreaks and cases of severe infec-tions, prevalence in different population segments and food handlers, and occurrence in food and drinking water. Cryptosporidium spp., Entamoeba histolytica, Giardia intestinalis, Trypanosoma cruzi and Toxoplasma gondii were the microorganisms most frequently involved in large outbreaks and/or severe infections, while Cyclospora cayetanensis was most frequently involved in single case reports. Cystoisospora belli was implied in severe infections in immunocompromised patients, while Blastocystis homi-nis, Sarcocystis spp., Dientamoeba fragilis, Endolimax nana and Pentatrichomonas hominis appeared to be less relevant for number of symptomatic infections and pathogenic potential. A progressive improvement in surveillance of protozoan infections and infection sources was highlighted, especially in developed countries. The apparent increase in cases was concomitant with the implementa-tion of reporting systems and the application of molecular diagnostic methods that represent valuable in-struments for establishing epidemiological links and preventing or limiting outbreaks. The pathogenic role and sources of infection should be better elucidated for some species.

Biocomposite membranes based on polylactic acid (PLA) and cellulose nanocrystals (CNCs) were developed using a scientific approach. Dicumyl peroxide (DCP) was used as a polymerization ini-tiator, while tin octoate (Sn(Oct)2) and triphenylphosphane (P(C6H5)3) were used as catalysts. A torque rheometer was used to mix the components of the biocomposite, and thin films was prepared by solvent casting. Fourier transform infrared (FTIR) spectroscopy confirmed the coupling between the PLA and CNCs. Field emission scanning electron microscopy (FESEM) showed that the CNCs were well-dispersed in the PLA matrix with an unimodal particle size distribution and a maximum particle size of around 200 nm. Thermogravimetric analysis (TGA) and differential scanning calo-rimetry (DSC) analysis demonstrated good thermal stability and improved biodegradability of the biocomposite membrane compared to pure PLA. Mechanical characterization showed a Young's modulus of 1.65 GPa, which is comparable to that of other composite materials, and a maximum tensile strength of 20.31 MPa, which is higher than that of pure PLA. These results suggest that the developed biocomposite membrane has potential applications in water filtration, food packaging, and biomedical devices.

As a result of this work, a previously unreported benzoxazine monomer based on 3,3'-dichloro-4,4'-diaminodiphenylmethane was obtained, characterized by 1H and 13C NMR spectroscopy, and its thermal and rheological properties were studied. A comparison between the properties of benzoxazines based on diamines (3,3'-dichloro-4,4'-diaminodiphenylmethane and 4,4’-diaminodimethylmethane). The effect of the reaction medium on the structure of the oligomeric fraction and the overall yield of the main product was studied. The synthesized monomers can be used as thermo- and fire-resistant binders for polymer composite materials, as well as hardeners for epoxy resins.

Maxillofacial defects, arising from trauma, oncological disease or congenital differences, detrimentally affect everyday life. Prosthetic repair offers the aesthetic and functional reconstruction with the help of materials mimicking natural tissues, among which polymers take unprecedented role. The three-dimensional (3D) printing techniques based on the computer-aided design, where polymers are essential, provide a rapid and cost-effective workflow protocol to perfectly restore patient-specific anatomy for prosthetics. This review discusses the main 3D printing approaches to maxillofacial prostheses fabrication: extrusion and lithography, which are radically preferable to the traditional methods. The main assessment criteria, affording the polymer implementation in 3D printing of prostheses, as well as the characteristics of the key advanced polymers, are considered. The success of the prosthesis is shown to be largely dependent on the retention system, predominantly using polymers in the form of adhesives and osseointegrated implants as a support for the prosthesis. The approaches and technological prospects are also discussed in the context of specific aesthetic restoration on the example of the nasal, auricle and ocular prostheses. 3D printing techniques determine the development of personalized approaches to improve aesthetic and functional effect of prosthetics in patients with maxillofacial defects.

Limonene epoxide (1,2 limonene oxide) readily reacts with carbon dioxide in a ring opening copolymerization reaction with insertion of CO₂ and formation of polycarbonates of exceptional chemical and physical properties. Both poly(limonene carbonate) and poly(limonene dicarbonate) can be synthesized using low cost Zn or Al homogeneous catalysts. This study addresses selected relevant questions concerning the technical and economic feasibility of limonene and carbon dioxide polymers en route to the bioeconomy.

A new approach for the preparation of polymer brush was developed via the union of controlled/“living” radical polymerization and click chemistry. The application of the approach realized the more quickly and accurate design and synthesis of the polymer brushes. A novel functional polymer brush of poly(acrylonitrile-g-glycidyl methacrylate) with tremendous application potential in the field of biology has been successfully synthesized via the new approach. The reaction conditions of click chemistry were optimized with the reaction time and the reactant ratio and judged from UV-vis spectra. Under the optimum of click chemistry, the novel functional polymer brushes were prepared. The GPC, FTIR analyses, 1H NMR spectrum and TGA were employed to ensure the successful synthesis of poly(acrylonitrile-g-glycidyl methacrylate) polymer brushes.

Radially polymerized dendritic compounds are nowadays an established polymer category next to their linear, branched and cross-linked counterparts. Their uncommon tree-like architecture is characterized by adjustable internal cavities and external groups. They are therefore exceptional absorbents and this attainment of high concentrations into their interior renders them ideal reac-tion media. In this framework they are applied in many environmentally benign implementa-tions. One of the most important among them is water purification though pollutant decomposi-tion. Simple and composite catalysts and photo-catalysts containing dendritic polymers and ap-plied in water remediation will be discussed jointly with some unconventional solutions and fu-ture prospects.

Cranio-maxillofacial structure is a region of particular interest in the field of regenerative medicine due to both its anatomical complexity and the numerous abnormalities affecting this area. However, this anatomical complexity is what makes possible the coexistence of different microbial ecosystems in the oral cavity and the maxillofacial region, contributing to the increased risk of bacterial infections. In this regard, different materials have been used for their application in this field. These materials can be obtained from natural and renewable feedstocks or by synthetic routes with desired mechanical properties, biocompatibility and antimicrobial activity. Hence, in this review, we have focused on bio-based polymers, which by their own nature, by chemical modifications of their structure, or by their combination with other elements, provide a useful antibacterial activity as well as the suitable conditions for cranio-maxillofacial tissue regeneration. This approach has not been reviewed previously, and we have specifically arranged the content of this article according to the resulting material and its corresponding application, reviewing guided bone regeneration membranes; bone cements; and devices and scaffolds for both soft and hard maxillofacial tissue regeneration, including hybrid scaffolds, dental implants, hydrogels and composites.

A new method for the synthesis of azido-propargyloxy derivatives of 1,3,5-triazine has been developed. The antibacterial activity against E. coli bacteria of propargyloxy substituted 1,3,5-triazines - 2,4,6-trispropargyloxy-1,3,5-triazine, 2-azido-4,6-bispropargyloxy-1,3,5-triazine and 2,4-diazido-6-propargyloxy-1,3,5-triazine and their hyperbranched polymers. It has been shown that the presence of an azide group in the compound directly affects the antibacterial activity. The cytotoxicity of these compounds against the M-HeLa, FetMSC and Vero cell lines was studied. The IC50 value was determined for low molecular weight compounds. It has been shown that hyperbranched polymers without azide groups don’t exhibit pronounced cytotoxicity and can be used in biomedical applications.

This study addresses the gap in research on the application of thermochromic polymers (TPs) in food packaging and their potential for real-time temperature monitoring, aiding in the assessment of food quality and shelf-life. TPs exhibit a visible color change in response to temperature varia-tions. A comprehensive systematic review (SR) across multiple engineering peer-review databases using predefined terms was conducted. Additionally, international patent databases were inves-tigated using the same predefined terms. Independent experts reviewed the methodology to identify and address potential biases. A total of 288 eligible articles and 922 patents were identified. After a duplicate selection and extraction process according to the inclusion criteria, four related full-text publications were selected from the initial 288 articles, and five relevant patents were selected from the 922 patents. The qualitative review suggests that TPs hold significant promise as food packaging materials due to their unique physical properties. The study concludes that TPs offer valuable properties for the food packaging industry, meriting further investigation to exploit their benefits fully.

Side-chain liquid crystal polymers have been mixed with ferromagnetic particles, and the for-mation of a monodomain in magnetic fields studied. At relatively low concentrations, the presence of ferroparticles substantially speeds up the rate of formation of a monodomain with the magnetic field and at a given concentration of ferrofluid that rate is independent of the magnetic field strength. In this way, rapid formation of a monodomain is possible at magnetic field strengths far lower than required for the liquid crystal polymer alone. This is anticipated to very helpful in the fabrication of devices based on monodomain liquid crystal elastomers. Wide angle x-ray scattering has been used to monitor the formation of the monodomain and small angle x-ray scattering can give some indication of the ferroparticle behaviour. A model is developed to explain the behaviour. The alignment properties of the ferroparticles is related to their ability to form chains under the influence of very low magnetic fields; these chains are of relatively low stability and may become disrupted after long times, high magnetic fields, or high concentrations. In general, the best results for alignment were at volume fractions below 1%, and under these con-ditions there is the potential for producing monodomain samples with improved properties; in particular shape changes with temperature are significantly larger as a result of improved backbone orientation. Experiments involving monodomain formation and director realignment suggest that the presence of ferroparticles results in a modification in the mechanism for alignment development driven by the organisation of the polymer backbone as a consequence of the con-straints offered by the morphology of the chains of ferroparticles.

Synthetic bone made of calcium phosphate is widely used for the clinical treatment of bone defects caused by trauma and bone tumors. Although synthetic bone is easy to use, its effects are only partial depending on the size and location of the bone defect, and there are many treatment options other than the use of synthetic bone. Various biodegradable polymers that are being considered for use as scaffolds for regenerative medicine are also being considered for use as synthetic bones; however, commercial synthetic bone products with performance comparable to that of calcium phosphate bioceramics have not yet been clinically applied. This review introduces the practice of bone regeneration therapy with synthetic bone and recent research on bone regeneration therapy with biodegradable polymers.

Thermal Non-destructive Testing and Evaluation (NDT&E) is crucial in ensuring the quality and safety of industrial materials, components, and structures. It serves as a key tool for assessing their operational reliability, thus enhancing safety in a wide range of industries. There is a growing demand for dependable, swift, remote, and secure inspection and assessment techniques to detect hidden flaws, especially for sustainable solutions prompts adjustments in design and manufacturing standards. Hidden defects often emerge during the service life of these materials and structures due to various stress factors, potentially resulting in catastrophic failures. This study delves into the optimal and dependable experimental method for conducting fast, remote, and secure inspections and assessments of carbon fiber reinforced polymer materials using Infrared Imaging (IRI) as part of Thermal Non-Destructive Testing and Evaluation (TNDT&E). Additionally, it examines the post-processing approach associated with this technique. This perspective also sheds light on the current state-of-the-art infrared imaging methods employed in TNDT&E, emphasizing their strengths and weaknesses about their ability to detect subsurface defects present within the material Most of the methods discussed in previous research primarily focus on the thermal differences in specific areas of a sample using processed thermal images, even though these images come from analyzing a series of images captured over time. This study highlights the latest research in thermal/infrared non-destructive testing and evaluation, along with the related post-processing techniques. It aims to not only show hidden subsurface defects through thermal differences also provides information about how these defects change over time.

In this research the possibility of using pH change to measure proton conductivity of proton exchange membranes (PEM) or else known as polymer electrolyte membranes are tested with using an experimental setup prepared by using pH meters. PEMs are an important part of the fuel cells and proton conductivity of the PEMs are one of the most important properties of the PEMs. Also, proton conductivity is the one of the biggest limiting factors of fuel cells thus it is important to measure the proton conductivity of the PEMs while trying new polymers or new types of membranes. But as current measurement methods do not have a standard and can be separated into mainly two different measurement methods which are Electron Impedance Spectroscopy (EIS) and Ion Exchange Capacity (IEC). EIS gives clearer results, but it needs an impedance analyzer machine, platinum electrodes and setup so this cannot be possible for every researcher due to its economical aspect. For IEC it is basically a titration method to see acid groups in the polymer or polymer matrix which are directly responsible for proton conductivity so this can show an indirect measurement of proton conductivity. But as for this one drawback are firstly this one is an indirect measurement and secondly needs overnight bath in solution can take long times. So, the possibility of using pH can be easier and both from time and economical aspect if it can be proven the give a direct relationship between pH change and proton conductivity.

Poly(vinylidene fluoride) nanocomposites processed with different morphologies, such as porous and non-porous films and fibres, have been prepared with silica nanoparticles (SiNPs) of varying diameter (17, 100, 160 and 300 nm) which in turn have encapsulated perylenediimide (PDI), a fluorescent molecule. Structural, morphological, optical, thermal, and mechanical properties of the nanocomposites, with SiNP filler concentration up to 16 wt% were evaluated. Further, cytotoxicity and cell proliferation studies were performed. All SiNPs are negatively charged independently of the pH and more stable from pH 5 upwards. The SiNPs introduction within the polymer matrix increases the contact angle independently of the nanoparticle diameters and the smallest ones (17 nm) improve the PVDF Young modulus from 0.94 ± 0.04 GPa for the pristine polymer film to 1.05 ± 0.06 GPa. Varying filler diameter, physico-chemical, thermal and mechanical properties of the polymer matrix were not significantly affected. Finally, the SiNPs inclusion does not induce cytotoxicity in murine myoblasts (C2C12) after 72 h of contact and proliferation studies reveal that the prepared composites represent a suitable platform for tissue engineering applications, as they allow to combine the biocompatibility and piezoelectricity of the polymer with the possible functionalization and drug encapsulation and release of the SiNP.

Microporous organic polymers (MOPs) are promising materials for gas sorption because of the intrinsic and permanent porosity, designable framework and low density. The introduction of nitrogen-rich building block in MOPs will greatly enhance the gas sorption capacity. Here, we report the synthesis of MOPs from the 2,4,6-tris(4-ethynylphenyl)-1,3,5-triazine unit and aromatic azides linkers via click polymerization reaction. FTIR and solid state 13C CP-MAS NMR confirm the formation of the polymers. CMOP-1 and CMOP-2 exhibit microporous networks with BET surface area of 431 and 406 m2 g-1 and narrow pore size distribution under 1.2 nm. Gas sorption isotherms including CO2 and H2 were measured. CMOP-1 stores superior CO2 level of 8.2 wt% (1.88 mmol g-1) at 273 K/1.0 bar and H2 uptake up to 0.6 wt% at 77 K/1.0 bar, while CMOP-2 with smaller surface area shows lower CO2 adsorption capacity of 7.3 wt% (1.66 mmol g-1) and H2 uptake (0.5 wt%). In addition, I2 vapor adsorption was tested at 353 K. CMOP-1 shows higher gravimetric load of 160 wt%. Despite of the moderate surface area, the CMOPs display excellent sorption ability for CO2 and I2 due to the nitrogen-rich content in the polymers.

The illicit use of fentanyl has led to hundreds of thousands of opioid-related deaths worldwide. Therefore, the detection of fentanyl by law enforcement and recreational users is of utmost importance. However, current detection methods are expensive, time-consuming, require special storage conditions and necessitate complex instrumentation that is generally unportable and requires skilled personnel to operate. An alternative approach would be using molecularly imprinted polymers (MIPs) as the recognition component of a handheld sensor, testing strip, or color-based assay. In this work, a molecularly imprinted polymer was made by using methacrylic acid (MAA) and ethyleneglycol dimethacrylate (EGDMA) as the functional monomer and cross-linking monomer respectively, and benzylfentanyl (Bfen) as the template. The use of benzylfentanyl is advantageous because it closely resembles the structure of fentanyl but does not have any physiological effects as a narcotic. Important studies herein determined the optimum ratio of the template:functional monomer, with subsequent evaluations of selectivity versus the commonly encountered narcotics such as heroin, cocaine, and methamphetamine. The data obtained from the HPLC analysis showed that the Bfen-MIP was successful in selectively binding the template and actual fentanyl, better than other common narcotics.

Geopolymers are ecologically-friendly inorganic materials which can be produced at low temperatures from industrial wastes such as fly ash, blast furnace slags or mining residues. Although to date their principal applications have been as alternatives to Portland cement building materials, their properties make them suitable for a number of more advanced applications, including as photocatalytic nanocomposites for removal of hazardous pollutants from waste water or the atmosphere. For this purpose, they can be combined with photocatalytic moieties such as metal oxides with suitable bandgaps to couple with UV or visible radiation, or with carbon nanotubes or graphene. In these composites the geopolymers act as supports for the photoactive components, but geopolymers formed from wastes containing oxides such as Fe2O3 show intrinsic photoactive behaviour. This review discusses the structure and formation chemistry of geopolymers and the principles required for their utilisation as photocatalysts. The literature on existing photocatalytic geopolymers is reviewed, suggesting that these materials have a promising potential as inexpensive, efficient and ecologically-friendly candidates for the remediation of toxic environmental pollutants and would repay further development.

Polymers in highly confined geometries can display complex morphologies including ordered phases. A basic component of a theoretical analysis of their phase behavior in confined geometries is the knowledge of the number of possible single-chain conformations compatible with the geometrical restrictions and the established crystalline morphology. While the statistical properties of unrestricted self-avoiding random walks (SAWs) both on and off-lattice are very well known, the same is not true for SAWs in confined geometries. The purpose of this contribution is a) to enumerate the number of SAWs on the simple cubic (SC) and face-centered cubic (FCC) lattices under confinement for moderate SAW lengths, and b) to obtain an approximate expression for their behavior as a function of chain length, type of lattice, and degree of confinement. This information is an essential requirement for the understanding and prediction of entropy-driven phase transitions of model polymer chains under confinement. In addition, a simple geometric argument is presented that explains, to first order, the dependence of the number of restricted SAWs on the type of SAW origin.

Seasonal changes and varying degree of corneal hydration has been linked to excimer laser corneal ablation rates. Use of PMMA as calibration material in refractive lasers is well established. However, PMMA ablation may be equally affected by seasonal variations in temperature and humidity, intern affecting the calibration process. Aim of this work is to analyze the effect of seasonal changes in PMMA Performance using SCHWIND AMARIS laser system. PET and PMMA ablations conducted in climate-controlled environment with 826 consecutive AMARIS systems manufactured over 6 years were retrospectively analyzed. Lasers were stratified depending on seasons and months of the year. Metrics like Single laser pulse fluence, nominal number of laser pulses, mean performance, standard deviation, and technical performance of system were compared to global average values. Cyclic winter-summer variation was confirmed with seasons winter and summer showing statistically significant variations with respect to global values. Metric technical performance showed deeper PMMA ablation performance in summertime, with maximum seasonal deviation of 6%. Results were consistently confirmed in seasonal as well as monthly analyses. These findings could help minimize variance among laser systems by implementing compensation factors depending on seasons such that laser systems installed worldwide follow the same trend line of variation.

Organic solar cells are contributing extensively to the production of future large area and cost-effective sources of renewable energy with a compact environmental impact. Moreover, due to tunable optical properties of the active medium, the semi-transparent organic solar cell can be fabricated and become a promising nominee for building Integrated Photovoltaics (BIPV), vehicles, and mobile electronic devices. Therefore, three newly synthesized polymers used as were host materials for the active medium and blended with beetroot dye. Hence, based on BHJ structure two ternary systems have been constructed and utilized to fabricate semitransparent solar cells and characterized. The results show that the natural dye has a crucial impact on solar cell characteristic parameters. Consequently, large value of V_OC close to 1V were obtained for ternary systems and acceptor material named PINDOLE exhibits potentials for electron transport layer (ETL) and shows an improvement in both fill factor and device efficiency.

The local and global order in dense packings of linear, semi-flexible polymers of tangent hard spheres are studied by employing extensive Monte Carlo simulations at increasing volume fractions. Chain stiffness is controlled by a tunable harmonic potential for the bending angle whose intensity dictates the rigidity of the polymer backbone as a function of the bending constant and equilibrium angle. The studied angles range from acute to obtuse ones, reaching the limit of rod-like polymers. We analyze how packing density and chain stiffness affect the ability of chains to self-organize at the local and global levels. The former corresponds to crystallinity as quantified by the Characteristic Crystallographic Element (CCE) norm descriptor, while the latter is computed through the scalar orientational order parameter. In all cases, we identify the critical volume fraction for the phase transition and gauge the established crystal morphologies, developing a complete phase diagram as a function of packing density and equilibrium bending angle. A plethora of structures is obtained, ranging from random hexagonal closed packed morphologies of mixed character and almost perfect face centered cubic (FCC) and hexagonal close-packed (HCP) crystals at the level of monomers, to nematic mesophases, with prolate and oblate mesogens at the level of chains. For rod-like chains, hysteresis is observed between the establishment of long-range nematic order and crystallization, while for right-angle chains both transitions are synchronized. A comparison is also provided against the analogous packings of monomeric and fully flexible chains of hard spheres.

Elastic peak electron spectroscopy, abbreviated EPES, involves ana- lyzing the line shape found in the elastic peak. The reduction in the energy of electrons of the elastic peak is a result of energy transfer to the target atoms, a phenomenon known as recoil energy. EPES differs from other electron spectroscopies in its unique ability to identify hydrogen in polymers and hydrogenated carbon-based materials. This feature is particularly noteworthy because lighter elements exhibit stronger energy shifts. The energy difference between the positions of the elastic peak of carbon and the elastic peak of hydrogen tends to increase as the kinetic energy of the incident electrons increases. If, during electron irradiation of an insulating polymer, the number of secondary electrons emitted by the surface is less than the number of electrons absorbed in the sample, the surface floats energetically until it stabilizes at a potential energy eVs. As a result, the interaction energy changes and modifies the energy difference between the elastic peaks of hydrogen and carbon. In this study, the charge effects are evaluated using the Monte Carlo method to simulate the EPES spectra of electrons interacting with polystyrene and polyethylene.

There have been many researches on the surface acoustic wave (SAW) sensors for detecting sulfur-containing toxic or harmful gases. This paper aims to give an overview of the current state of the polymer films used in SAW sensors for detecting deleterious gases. By covering most of the important polymer materials, the structures and types of polymers are summarized, and a variety of devices with different frequency, such as delay lines and array sensors for detecting mustard gas, hydrogen sulfide and sulfur dioxide are introduced. The preparation method of polymer films, the sensitivity of the SAW gas sensor, the limit of detection, the influence of temperature and humidity, and the anti-interference ability are discussed in detail. The advantages and disadvantages of the films are also analyzed, and the potential application of polymer films in the future is also forecasted.

Thermal shape memory polymers (SMPs) find increasing applications in biology and medicine due to their promising potential for improved biocompatibility. In such applications, the inevitable penetration of small molecules from the ambient fluid into the polymer influences the shape recovery process and often leads to a reduction of the temperature, at which shape recovery takes place. We show here via molecular dynamics simulations that the size of additive molecules plays a key role for this process. While the effect of concentration on the recovery rate is monotonic in the investigated range, a non-monotonic dependence on the size of additive molecules emerges at temperatures close to the glass transition. This work thus identifies the additives’ size to be a qualitatively novel parameter for switching the recovery process in polymer-based shape memory materials.

The persistent issue of bacterial and fungal colonization of artificial implantable materials and decreasing efficacy of conventional systemic antibiotics used to treat implant-associated infections has led to the development of a wide range of antifouling and antibacterial strategies. This article reviews one such strategy where inherently biologically active renewable resources, i.e. secondary plant metabolites (SPMs) and their naturally occurring combinations (i.e. essential oils) are used for surface functionalization and synthesis of polymer thin films. With a distinct mode of antibacterial activity, broad spectrum of action and diversity of available chemistries, secondary plant metabolites present an attractive alternative to conventional antibiotics. However, their conversion from liquid to solid phase without significant loss of activity is not trivial. Using select examples, this article shows how plasma techniques provide a sufficiently flexible and chemically reactive environment to enable the synthesis of biologically-active polymer-coatings from volatile renewable resources.

This research is completed in development of researches devoted to relations between elastic modulus (MoE) and thermal expansivity (CTe) of different materials. This study experimentally confirmed the relation of MoE and CTe for thermosetting polymers and FRPs both under normal and heating temperatures. As the thermosetting polymers, the epoxy compositions were used and glass fiber and mineral additives for FRP. The experiment was based on dilatometric and elastic deformations’ testing. Also, the relaxation model of MoE/CTe was proposed, that is based on physical properties of polymers’ supramolecular structures. The comparative analyzing of MoE/CTes’ different models is done. The most accurate models are determined, and the relaxation model has demonstrated the high accuracy.

Damage to peripheral arteries by the atherosclerotic process accounts for about 3% of the world's population, which puts this problem in the category of major social problems. Modified lipoproteins and cholesterol crystals are known to accumulate in the arterial intima and cause the formation of proatherogenic macrophages, foam cells, and inflammation. Defective efferocytosis of apoptotic foam cells leads to the formation of a necrotic core, a sign of failure to resolve inflammation. Resolution of inflammation is mediated by specialized pro-resorption lipid mediators, proteins and signaling gases. Improving the balance between pro-inflammatory and anti-inflammatory factors contributes to the reverse development of local atherogenesis. Active direct intervention in the reconstruction of the adventitial layer of the arterial wall using cholesterol-affinity polysaccharide hydrogels containing a cocktail of growth factors creates conditions for the formation of additional extracellular matrix and reversal of cholesterol mass from the subintimal zone. Creating concentration and electrostatic gradients in the adventitia zone using a hydrogel may be one of the effective ways to degrade early soft atherogenic plaques and locally restore the damaged structure of the vessel wall. Growing scientific interest in the previously insufficiently studied adventitia indicates its important role in angionesis and atherogenesis.

Surface modification of polypropylene (PP) films is achieved using gamma-irradiation-induced grafting to proffer with antimicrobial activity. The copolymer was obtained through a versatile two-step route; pristine PP is exposed to gamma rays and grafted using methyl methacrylate (MMA), then N-vinylimidazole (NVI) is grafted onto the copolymer PP-g-MMA by simultaneous irradiation. The characterization included Fourier-Transform Infrared Spectroscopy (FTIR), Scanning Electron Microscope (SEM), Thermogravimetric Analysis (TGA), X-ray Photoelectron Spectroscopy (XPS), and physicochemical analysis of swelling and contact angle. The copolymer (PP-g-MMA)-g-NVI was loaded with vancomycin, and the drug released was quantified by UV-vis spectrophotometry at different pH. The surface of (PP-g-MMA)-g-NVI exhibited pH-responsiveness and moderate hydrophilicity, suitable properties for controlled drug release.

Engineering of drug nanocarriers combining fine-tuned mucoadhesive/mucopenetrating properties is currently being investigated to ensure more efficient mucosal drug delivery. Aiming to improve the transmucosal delivery of hydrophobic drugs, we designed a novel kind nanogel produced by the self-assembly of amphiphilic chitosan graft copolymers ionotropically crosslinked with sodium tripolyphosphate. In this work, we synthesized for the first time chitosan-g-poly(methyl methacrylate) nanoparticles thiolated by the conjugation of N-acetyl cysteine. First, we confirmed that both non-crosslinked and crosslinked nanoparticles in the 0.05-0.1% w/v concentration range display very good cell compatibility in two cell lines that are relevant to oral delivery, Caco2 cells that mimic the intestinal epithelium and HT29-MTX cells that produce mucin. Then, we evaluated the effect of crosslinking, nanoparticle concentration and thiolation on the permeability in vitro utilizing monolayers of (i) Caco2 and (ii) Caco2:HT29-MTX cells (9:1 cell number ratio). Results confirmed that the ability of the nanoparticles to cross Caco2 monolayer was affected by the crosslinking. In addition, thiolated nanoparticles interact more strongly with mucin, resulting in a decrease of the apparent permeability coefficient (Papp) compared to the pristine nanoparticles. Moreover, for all the nanoparticles, higher concentration resulted in lower Papp suggesting indicating that the transport pathways could undergo saturation.

Reactions of N‚N'-bis(3-methylpyridyl)oxalamide (L1), N,N’-bis(3-methylpyridyl)adipoamide (L2) and N,N’-bis(3-methylpyridyl)sebacoamide (L3) with tricarboxylic acids and Cu(II) salts afforded {[Cu(L1)(1,3,5-HBTC)]·H2O}n (1,3,5-H3BTC = 1,3,5-benzenetricarboxylic acid), 1, {[Cu1.5(L2)1.5(1,3,5-BTC)(H2O)2]·6.5H2O}n, 2, [Cu(L2)0.5(1,3,5-HBTB)]n (1,3,5-H3BTB = 1,3,5-tri(4-carboxyphenyl)benzene), 3, [Cu4(L3)(OH)2(1,3,5-BTC)2]n, 4, {[Cu3(L3)2(1,3,5-BTB)2]·2.5MeOH·2H2O}n, 5, and {[Cu3(L3)2(1,3,5-BTB)2 ]·DMF·2H2O}n, 6, which have been structurally characterized by using single crystal X-ray crystallography. Complexes 1 – 4 form a 2D layer with the {44.62}-sql topology, a 2D layer with the (4.62)2(42.62.82)-bex topology, a 3-fold interpenetrated 3D net with the (412.63)-pcu topology and a 3D framework with the (410.632.83)(42.6)2(43.63) topology, respectively, whereas 5 and 6 are 3D frameworks with the (63)2(64.82)(68.85.102) topology. Complex 5 shows a better iodine-adsorption factor of 290.0 mg g-1 at 60 oC for 360 minutes than the other ones, revealing that the flexibility of the spacer ligand governs the structural diversity and the adsorption capacity.

The current work investigates the auxetic tensile deformation behavior of the inversehoneycomb structure with 5 × 5 cells made of biodegradable poly(butylene adipate-coterephthalate) (PBAT). Fused deposition modeling, an additive manufacturing method, produced such specimens. Residual stress (RS) and warpage, more or less, always exist in such specimens due to layer-by-layer fabrication, i.e., repeated heating and cooling. The RS influences the auxetic deformation behavior, but its measurement is challenging due to the very fine structure. Instead, the finite-element(FE)-based process simulation realized by an ABAQUS plug-in numerically predicts the RS and warpage. The predicted warpage shows a negligible slight deviation compared to the design topology. This process simulation also delivers the temperature evolution of a small volume material, revealing the local cyclic heating and cooling. The achieved RS serves as the initial condition for the FE model used to investigate the auxetic tensile behavior. With the outcomes from FE calculation without considering RS at hand, the effect of the RS on the deformation behavior is discussed for the global force-displacement curve, the structural Poisson’s ratio evolution, the deformed structural status, the stress distribution, and evolution, where the first three and the warpage are also compared with experimental results. Furthermore, the FE simulation can easily provide the global stress-strain flow curve with the total stress calculated from the elemental ones.

Intranasal (i.n.) administration became an alternative strategy to bypass the blood-brain barrier and improve drug bioavailability in the brain. The main goal of this work was to preliminarily study the biodistribution of mixed amphiphilic mucoadhesive nanoparticles made of chitosan-g-poly(methyl methacrylate) and poly(vinyl alcohol)-g-poly(methyl methacrylate) and ionotropically crosslinked with sodium tripolyphosphate in the brain after intravenous (i.v.) and i.n. administration to Hsd:ICR mice. After i.v. administration, the highest nanoparticle accumulation was detected in the liver, among other peripheral organs. After i.n. administration of a 10-times smaller nanoparticle dose, the accumulation of the nanoparticles in off-target organs was much lower than after i.v. injection. In particular, the accumulation of the nanoparticles in the liver was 20 times lower than by i.v. When brains were analyzed separately, intravenously administered nanoparticles accumulated mainly in the “top” brain, reaching a maximum after 1h. Conversely, in i.n. administration, nanoparticles were detected in the “bottom” brain and the head (maximum reached after 2 h) owing to their retention in the nasal mucosa and could serve as a reservoir from which the drug is released and transported to the brain over time. Overall results indicate that i.n. nanoparticles reach similar brain bioavailability, though with a 10-fold smaller dose, and accumulate in off-target organs to a more limited extent and only after redistribution through the systemic circulation. At the same time, both administration routes seem to lead to differential accumulation in brain regions and thus, they could be beneficial in the treatment of different medical conditions.

Due to their distinct physical, chemical, and biological characteristics, biopolymers, in particular Poly Ethylene Glycol (PEG) and Cellulose, are frequently used in biomedical medicine as drug or vaccine delivery systems. In this study, we have done a systematic review and a meta-analysis to compare current developments in many PEG and cellulose-based hydrogels, including double network hydrogels, injectable hydrogels, sliding hydrogels, conductive hydrogels, responsive hydrogels, and nanocomposite hydrogels. The pharmacokinetic properties, including physicochemical properties, biocompatibility, biodegradability, temperature, and pH, have been studied as these critical factors are to be considered for deciding the suitability of the drug for delivery. Moreover, the study has evaluated the controlled-release parameters such as half-life, circulation time, maximum release percentage of loaded drug released, burst release, maximum release, and drug-release kinetics. Finally, the efficacy and immune response of hydrogel was studied for future choice, including the cellulose hydrogel system in COVID-related long-term vaccine delivery. The finding revealed that cellulose-based hydrogel is effective for vaccine delivery.

In the face of the current energy and environment problems, the full use of biomass resources instead of fossil energy to produce a series of high-value chemicals has great application prospects. 5-hydroxymethylfurfural (HMF), which can be synthesized from lignocellulose as raw material, is an important biological platform molecule. Its preparation and catalytic oxidation of subsequent products have important research significance and practical value. In the actual production process, porous organic polymer (POPs) catalysts are highly suitable for biomass catalytic conversion due to its high efficiency, low cost, good designability, and environmentally friendly features. Here, we briefly described the application of various types of POPs (including COFs、PAFs、HCPs、CMPs) in the preparation and catalytic conversion of HMF from lignocellulosic biomass, and analyzed the influence of the structural properties of catalysts for the catalytic performance. Finally, we summarized some challenges that POPs catalysts will face in biomass catalytic conversion, and prospected the important research directions in future. This review would provide valuable references for the efficient conversion of biomass resources into high-value chemicals in practical applications.

This review provides an extensive overview of the developments in the field of polymer science, focusing on the solid-state modification (SSM) of thermoplastic materials. The background of the study places thermoplastics within the context of their increased use over the past century, highlighting their versatility in various applications and the associated environmental and health concerns due to certain additives. The methods section delves into the specifics of SSM, a technique that involves the incorporation of monomers or oligomers into the amorphous phase of polymers through multiple exchange reactions, distinguishing it from traditional melt polymer modification methods. The results section outlines the unique aspects of SSM and its increasing recognition for its potential to enhance material performance in areas such as catalysts and composites. It also discusses the application of SSM in modifying different thermoplastic polymers, highlighting various studies demonstrating the method's effectiveness in altering polymer properties. Finally, this work emphasizes SSM's importance in environmental sustainability and its potential in the recycling and upcycling of plastic materials. It acknowledges the challenges and future perspectives in the field, particularly regarding the scalability of SSM techniques for industrial applications and their role in advancing a circular economy in the polymer industry.

Water-soluble nonionic surfactant, pentaethylene glycol monododecyl ether, C12E5, spontaneously blooms to the surface of spin-cast hydrophobic polyiso-prenes, generating hydrophilic surfaces. This system represents a simple model for hydrophilic chemical modification of rubbery polymers yet demonstrates surprisingly rich, complex and unexpected behaviour. The ver-tical depth profiles were quantified using neutron reflectometry (NR) and deuterated surfactant, and the surface properties were characterized using con-tact angle analysis and atomic force microscopy (AFM). Despite the low surface tension of the toluene solvent used in film preparation and the low surface en-ergy of the PI matrix, NR depth profiles revealed clear evidence of surfactant segregation. This surface layer was typically thicker than a monolayer, but incomplete, yet was remarkably stable with respect to dissolution, even when exposed to hundreds of thousands of times the volume of water required to dissolve all the surfactant on the surface. Despite the apparent resistance to removal from the surface, water exposure does alter the subsequent wettabil-ity of the surface, with a hydrophilic-to-hydrophobic transition occurring after rinsing. Complementary AFM images of these C12E5 / cis-PI films showed unexpected strand-like features on the surface of the film, which we attribute to a non-uniform lateral distribution of some of the surfactant. This surface structure becomes more evident after rinsing, and it appears that there are two distinct populations of surfactant on the PI film surface. We conclude that some of the bloomed surfactant exists as layers, which are relatively inert with respect to rinsing or surface modification, and some is laterally inhomogene-ous. This latter population is primarily responsible for surface wetting be-havior, but is not detected by specular NR.

Braskem is the only company in the world that produces green polyethylenes (HDPE – high density polyethylene and LLDPE – linear low density polyethylene) derived from the dehydration of sugarcane ethanol. Although the performance of green and fossil nominally same polyethylenes are equivalent, commercial clients may use blends of up to 51% of green polyethylenes and 49% of fossil polyethylenes and still have the right to use the I’m greenTM label which appeals to environmental conscious consumers and places these companies in a noticeable position. The Annual Income Statement - AISs from 2010, when Braskem started production of green PE, until 2018, show there was growth of revenues. Despite of the production of polyethylenes have continued stable and the number of green polyethylenes patents have decreased since 2014, the profits with the BRKM5 stocks increased. There is no transparency of how carbon credits were gained and in the AIS. Investments in securities in the Brazilian financial market (BRKM5 and carbon credits) are much more attractive than the investment in new patents, because they generate greater gains (268% increase in the average share price of BRKM5 from 2012 to 2018) and do not require large investments in R&D.

A study on the selection of hyperelastic constitutive model for polymeric materials is performed using a hybrid experimental-computational approach. Bis-GMA polymer is used as a case study of hyperelastic material to describe the polymer characteristics by determining its Poisson’s ratio and its valid range of the hyperelastic stress-strain curves. These two parameters are then used to determine the hyperelastic constitutive model by using the hybrid approach. Several uniaxial compression tests along with their finite element simulations are implemented in a systematic way, to identify the polymer behavior under the compressive loading conditions. Nano-indentation experiments are conducted to verify the hyperelastic behavior of the polymer. The experimental and computational evidences confirm that the Poisson’s ratio of Bis-GMA is 0.40 and the appropriate hyperelastic constitutive model for this polymer is of a second order polynomial. It is shown that, the results can be used to determine the true stress-strain curve of hyperelastic materials.

Adhesion of polymers to surfaces is of upmost importance in timely applications such as protective coatings, biomaterials, sensors, new power sources and soft electronics. In this context, this work examines the role of molecular interactions in the adhesion of polypyrrole thin films to flexible Indium Tin Oxide (ITO) electrodes grafted with aryl layers from various diazonium salts, namely 4-carboxybenzenediazonium (ITO-CO₂H), 4-sulfonicbenzenediazonium (ITO-SO₃H), 4-N,N dimethylbenzenediazonium (ITO-N(CH₃)₂), 4-aminobenzenediazonium (ITO-NH₂), 4-cyanobenzenediazonium (ITO-CN) and 4-N-phenylbenzenediazonium (ITO-NHPh). It was demonstrated that PPy thin layers were adherent to these surfaces, whereas adhesion failure was noted on bare ITO, following simple solvent washing or sonication. Adhesion of the polypyrrole was investigated in terms of the hydrophilic/hydrophobic character of the underlying aryl layer as probed by contact angle measurements. It was found that sulfonic acid doped polypyrrole (PPy-BSA) thin films were preferably deposited on the most hydrophobic surfaces. More importantly, the redox properties and electrochemical impedance of PPy were closely related to the hydrophobic character of the aryl layers. This work demonstrates that diazonium compounds are unique molecular glues for conductive polymers, and permit to tune their interfacial properties. With diazonium-based robust, architectured interfaces, one can design high performance materials for e.g.sensors, printed soft electronics and flexible thermoelectrics.

The aim of this work is the preparation of contact active antimicrobial films by blending copolymers with quaternary ammonium salts and polyacrylonitrile as matrix material. A series of copolymers based on acrylonitrile and methacrylic monomers with quaternizable groups were designed with the purpose of investigating the influence of their chemical and structural characteristics on the antimicrobial activity of these surfaces. The biocide activity of these systems was studied against different microorganisms, such as the Gram-positive bacteria Staphylococcus aureus and the Gram-negative bacteria Pseudomona aeruginosa and the yeast Candida parapsilosis. The results confirmed that parameters such as flexibility and polarity of the antimicrobial polymers immobilized on the surfaces strongly affect the efficiency against microorganisms. In contrast to the behavior of copolymers in water solutions, when they are tethered to the surface, the active cationic groups are less accessible and then the mobility of the side chain is critical for a good contact with the microorganism. Blend films composed of copolymers with high positive charge density and chain mobility present up to a more than 99.999% killing efficiency against the studied microorganisms.

This study was conducted to explore the potential of superabsorbent polymers (SAPs) from used disposable diapers as soil moisture conditioner. Swelling behavior of the proposed hydrogel in response to external stimuli such as salt solutions, temperature and pH was studied. In addition, laboratory experiments were carried out to evaluate the effects of incorporation hydrogel on germination of bean (Phaseolus vulgaris L.) and pumpkin (C. pepo) seeds. The structure of the superabsorbent was characterized by Fourier transform infrared spectroscopy (FTIR). The results indicate that the proposed SAP exhibited a maximum swelling capacity of 189 g.g-1 of dry gel. It was observed that the swelling capacity decreased with an increase in the ionic strength of the swelling medium. When this SAP was mixed with sandy soil, the mixture was able to lose water more slowly. The seeds germination and seedling growth was remarkably influenced by the application of 0.5, 1.0 and 2.0 w/w% of SAP compared to the untreated soil. Therefore, it follows that it is possible to take advantage of SAPs property from used disposable diapers to retain the moisture in soil as an alternative to value the use of such waste, showing that it has potential for diverse applications in agriculture.

In this paper, based on our previous expertise on ceramic artifacts, several archaeometric methods applied to some samples collected from the Dudești archaeological site (Oltenia region, Romania) are reported for the first time in the literature. The chemical composition and microstructural and morphological characterization of these samples offer important conclusions about the processing conditions. Some specific techniques such as X-ray diffraction (XRD), wave-length-dispersive X-ray fluorescence (WDXRF), Optical microscopy (OM), stereomicroscopy, scanning electron microscopy (SEM), Fourier transform infrared (FTIR) spectroscopy and Raman spectroscopy, provide composition information about pigments and their decay processes. Additionally, the Brunauer-Emmett-Teller (BET) method helps to estimate pore sizes and specific surface areas. Thermal analysis (TGA) was used to establish details regarding the production technology and the raw materials source used to make the ceramics, too. The obtained results indicated that the ceramics are based on a paste of muscovite, feldspar, with high plasticity, quartz, melanterite, and calcite, the latter in very low concentrations. According to the obtained results, we could assume that non-calcareous clays are present in the investigated samples because calcium exists in low concentrations. Gypsum is present, too, in very low concentration, identified by the presence of sulfate group in WDXRF. In the same context, iron oxides significantly impact the firing atmosphere of iron-rich clay, resulting in blackening under reducing conditions and reddish coloration under oxidative conditions. Using hematite and gypsum as pigments further contributes to the color variations in the pottery. The consistent firing temperature range of 200-600 °C in Dudești pottery implies a standardized production process, the variation in color being dependent on the specific reducing/oxidative regime conditions. This relationship between clay composition and local sources suggests a connection to Neolithic pottery production in the region and their color depending on the reducing/oxidative regime conditions.

A microwave technique prepared a superabsorbent polymer (SAP) by grafting two hydrophilic monomers onto a polysaccharide substrate. The monomers used are acrylic acid (AA) or acrylamide (AM) to graft onto a pullulan substrate (PUL) to form PUL-g- AA (SAP1) and PUL-g- AM (SAP2), respectively. The monomers (AM/AA) graft together onto a PUL substrate to form PUL-g-(AM/AA) (SAP3). Grafting parameters such as grafting efficiency with percentage, conversion of monomer to polymer, gel content, water retention, water adsorption capacity, and swelling kinetics were determined. Additionally, the effect of environmental pH (2, 4, 7, 9, and 12) and sodium dodecylbenzene sulfonate (SDBS) surfactant was evaluated, where SDBS was added by 1,2,3,4 and 5 mM to form (SAP4 to SAP8). FTIR results show that AM grafted on PUL through an aliphatic C-N bond, while AA grafting occurred through a single C-C bond. The grafting efficiency with AM is higher than with AA, as well as their gel contents. Water absorbance capacity increased with grafting of AA or AM separately, and water retention was enhanced. The highest absorbent capacity, water retention, gel content, and grafting parameters values were obtained with 3 mM SDBS content and pH7. The swelling kinetics showed that the increases in the theoretical and experimental swelling equilibriums were 72 % and 82%, respectively, at SAP6 compared to the values of these parameters in SAP3. The water absorption capacity of the hydrogel increases with increasing pH to 7 and then gradually decreases. XRD improves the crystallinity and crystalline size of the hydrogel after grafting polymerization for AM/AA into PUL, in addition to enhancing thermal stability. On the contrary, FE-SEM demonstrated that SDBS improves the porosity and pore size of the hydrogel surface in SAP6.

Development of load-bearing polymer composite constructions in civil engineering, such as industrial chimneys and gas ducts, requires filling some research gaps. These gaps are related to long-term behavior under mechanical and temperature loads, cyclic ones as well. Such conditions mean that viscoelasticity should be considered. First of all, viscoelastic parameters should be calculated, based on the used inner structure model. Then, due to the high working temperatures, thermal aging should be considered as well. This research is devoted to effects of thermal aging on viscoelastic behavior of polymers. Two sets of experiments were conducted: creep tensile tests and cyclic heating in constrained state. The Kelvin-Voigt viscoelasticity model was used to determine the rheological parameters of binder from experimental creep curves. Thermally-aged binder turned out to lose its viscous properties and became elastic. Cyclic heating was used to compare the behavior of normal and thermally-aged binder and to evaluate the possibility of temperature stress accumulation. Similar to creep tests, cyclic heating showed that aged binder lost viscosity and worked almost perfectly elastic. Non-aged binder was prone to stress accumulation much more. As a result, the rheological behavior of aged and non-aged binder was compared and showed a significant difference. In addition, the influence of temperature stress accumulation on stress—strain state was evaluated and turned out to be significant as well. The obtained results can be further used to predict the mechanical behavior of structures made of polymer composites operating for a long time at elevated temperatures, including those exceeding the glass transition temperature.

Inspired by the process of bone formation in living organisms, many studies have been conducted to develop organic-inorganic composite materials by generating calcium phosphate crystals within solutions or dispersions of polymers with appropriate functional groups. Bones are composite materials consisting of organic polymers (mainly Type I collagen), carbonated apatite, and water, with volume fractions 35-45%, 35-45%, 15-25%, respectively. Carbonated apatite in bone contributes to rigidity, while organic polymers and water contribute to toughness. The inorganic crystal, carbonated apatite, is a plate-shaped crystal with dimensions of 50 nm × 25 nm × 1-4 nm, generating a significant organic-inorganic interface due to its nanoscale size. This interface is believed to absorb externally applied forces to dissipate mechanical energy to thermal energy. Creating such nanometer-scale structures using top-down approaches is challenging, making bottom-up methods like co-precipitation of polymer and inorganic crystals more suitable. In this account, efforts to develop eco-friendly mechanical materials using biomass such as cellulose and starch based on the bottom-up approach to bone-like composites are described.

The synthesis and crystal structure of pyrazine-2,5-diyldimethanol (pzydmH2, C8H8N2O2) a new symmetric water-soluble N,O-chelating tetra-dentate organic ligand is reported and an environmentally friendly method was used to synthesize coordination compounds in water under ambient conditions from the reaction of pzydmH2 with the halide salts of Cu(II), Zn(II), Hg(II) and Cd(II): {[Cu(pzydmH2)0.5(µ-Br)(Br)(H2O)]·H2O}n 1, {[Zn2(pzydmH2)(µ-Cl)(Cl)3(H2O)]·H2O}n 2, [Hg2(pzydmH2)0.5(µ-Cl)2(Cl)2]n 3, {[Cd2(pzydmH2)(µ-Cl)4]·H2O}n 4, and {[Cd2(pzydmH2)(µ-Br)4]·H2O}n 5. Single-crystal X-ray diffraction analysis revealed that 1-3 are 1D coordination polymers and 4 and 5 are 3D coordination networks, all constructed by bridging pyrazine-2,5-diyldimethanol and halogen ions. The hydroxyl groups in the organic linker extend the 1D chains to non-covalent 3D networks. In all non-covalent and covalent 3D networks water molecules were trapped by strong hydrogen bond interactions. Supramolecular analysis revealed strong O-H···O, O-H···N, O-H···X and week of C-H···O, C-H···X (X = Cl, Br) hydrogen bonds, as well as π-π(pyrazine ring), metal-halogen···π(pyrazine ring) and O-H···ring(5-membered chelate ring) interactions. Also X···O weak halogen bonds are present in 1-5 (X = Cl and Br).

The kinetics and efficacy profiles of photoinitiated polymerization are theoretically presented. For the same dose, lower light intensity achieves a higher steady-state-efficacy (SSE) in type-I; in contrast, type-II has an equal SSE. Higher light intensity has a faster rising efficacy, due to faster depletion of photoinitiator (PS) concentration. However, type-II process is also affected by the available oxygen. Higher light intensity produces more efficient singlet oxygen, resulting a higher transient efficacy, in which all intensities reach the same SSE when oxygen is completely depleted. With external oxygen, type-II efficacy increases with time, otherwise, it is governed only by the light dose, i.e., same dose achieves same efficacy. Moreover, type-II has an efficacy follows Bunsen Roscoe law (BRL), whereas type-I follows non-BRL. The measured type-I efficacy and gelation profile are analyzed by our analytic formulas. Schematics of the photocrosslinking stage defined by the availability of oxygen is developed, where both type-I and –II coexist until the oxygen is depleted. The overall efficacy may be enhanced by resupply of PS or oxygen during the light exposure. The roles of light dose and PS concentration on the efficacy of photoinitiated polymerization should be are governed a new concept of a volume efficacy (Ve), defined by the product of the crosslink (or gelation) depth (CD) and local [efficacy].

The synthesis these past few years of novel organic molecules that spontaneously self-assemble into a large variety of molecular architecture, particularly generating organogels, has opened up new horizons for preparing functional materials. Here, we present an original preparation path of such materials through the making of hybrid gels of these molecules together with covalent polymers. Three types of systems are described: i) intermingled gels where a polymer gel and an organogel pervade one another; ii) encapsulation of self-assembled filaments in polymer fibrils, which provides a system with unusual magnetic properties; iii) the reverse situation where self-assembled nanotubes sheathe polymer fibrils. Here two covalent polymers are considered: a neutral polymer, namely stereoregular polystyrene (isotactic or syndiotactic), and a semi-conducting polymer, P3BT. In the latter case, semi-conducting nanowires are obtained.