Measuring reference evapotranspiration (ETo) is a difficult and costly process. Several parameters are needed to calculate it from meteorological parameters with the aid of some developed equations. There may be variable microclimates in some regions and these are often quite far from the climate stations. Therefore, for ETo, it is better to prefer local measurements rather than relying on regional values. ETo is of great importance for all water-related sectors. It is the primary factor designating the amount of irrigation water to be applied to the plant rootzone in agricultural activities. The amount of irrigation water to be applied is determined by correcting ETo value with the plant coefficient (kc) and irrigation efficiency. There have been many developments in measurement/calculation of ETo in recent years and it is expected that there will be more in the future. Within the scope of this study, ETo values measured with ETgage equipment were compared with the monthly ETo values calculated with the use of Thornthwaite, Blaney-Criddle, Cropwat (FAO Penman Monteith), Jensen-Haise and ASCE standardized Penman Monteith (ASCE SZ PM) methods. In terms of total ETo value, Thornthwaite (17%) and Jensen-Haise (14%) methods yielded lower values than ETgage readings. On the other hand, Blaney-Criddle (15%), Cropwat FAO PM (10%) and ASCE SZ PM (30%) methods yielded greater values than ETgage readings. Among the calculation methods, in Cropwat software, FAO PM equation yielded the closest value to ETgage readings. It was concluded based on present findings that ETgage equipment could reliably be used in determination of ETo.

Effective and rapid mixing is essential for various chemical and biological assays. The present work reports a simple and low-cost micromixer based on magnetofluidic actuation. The device takes advantage of magnetoconvective secondary flow, a bulk flow induced by an external magnetic field, for mixing. A paramagnetic stream of diluted ferrofluid and a non-magnetic stream are introduced to a straight microchannel. A permanent magnet placed next to the microchannel induced a non-uniform magnetic field. The magnetic field gradient and the mismatch in magnetic susceptibility between the two streams create a body force, which leads to rapid and efficient mixing. The micromixer reported here could achieve a high throughput and a high mixing efficiency of 90 % in a relatively short microchannel.

Freeze drying (FD) is a technique used to preserve the bioactive content and flavor of samples. Foods with a short shelf life due to nature have been preserved by FD in recent years. The success of the drying technique is thanks to the high retention ability of the bioactive compounds and the flavor of the sample. However, the high cost and energy consumption of the FD limit its usage in several fields. Freezing, primary drying, and secondary drying, which take place in the same device, are the stages of the FD. In addition, several parameters, including pretreatment, size, temperature, sample species, time, and pressure, affect the FD process. These parameters are controlled to increase the effectiveness of the FD on the samples. Moreover, FD was compared with other drying techniques including hot-air drying, microwave drying, vacuum drying, and solar drying to determine its protective capability. It has also been applied to the valorization of waste products, which is a common problem worldwide. For valorization, microencapsulation and powder production have been achieved by FD. In recent years, studies on the effects and use of the FD on various materials increased, providing new aspects for the future of science and food industry.

The lithium-ion batteries are widely used as a power source for portable devices, including cell phones. The useful life is about 2 years or 500 cycles, contributing to the generation of waste from electrical and electronic equipment (WEEE). Mining of lithium and cobalt damages the environment and is onerous; therefore, sustainable alternatives, such as obtaining these elements from secondary sources as recycling of lithium-ion batteries, are essential to provide the inputs used in the sector. However, the metallurgical route which will used to recovering them must be considered, due to this work aims for a more environmentally favorable process using DL-malic acid 1.5 M and instead of compared with sulfuric acid 2 M, heat pretreatment of 1 h and 3 h, and for all conditions, experiments were carried out with and without adding the oxidizing agent hydrogen peroxide. The best yields occurred in presence of H2O2 10 % v/v, and heat pretreatment of 1 h: 33.49 % Co and 4.63 % Li, and 29.78 % Co e 3.44 % Li were recovered by sulfuric acid and DL-malic acid, respectively.

Epithelial–mesenchymal transition (EMT) is defined as a cellular process during which epithelial cells acquire mesenchymal phenotypes and behavior following the downregulation of epithelial features. EMT and its reversed process, the mesenchymal-epithelial transition (MET), and the special form of EMT, the endothelial-mesenchymal transition (EndMT), have been thought as a universal dogma controlling developmental and pathological processes. More than half a century of EMT study has made it a large research field and a mainstream concept. However, discrepancies and disputes over EMT and EMT research have also grown over time. Particularly, neither the epithelial and mesenchymal states/properties nor their regulatory networks nor specific markers have been defined, rendering the EMT, MET and EndMT concepts groundless. Moreover, EMT and MET effects should not be a cause, but rather a consequence of or an accompanying effect during developmental and pathological processes. EMT and MET represented by the change in cell shapes or adhesiveness or symbolized by EMT factors are biased interpretation of the overall change in cellular property and regulatory networks during development and cancer progression. The true meaning of EMT effects in some developmental and pathological processes, such as fibrosis, needs re-evaluation. But the core EMT factors are actually a few components of the regulatory networks of neural stemness, which determines tumorigenicity and pluripotency. The EMT effects in cancer progression and neural crest formation are wrong attribution of the role of neural stemness during cancer progression and the cell-intrinsic property of neural crest cells to the unknown mesenchymal state. It is time to reassess the significance of EMT and its related concepts in scientific research.

Nanoporous membranes promise energy-efficient water desalination. Hexagonal boron nitride (h-BN), like graphene, exhibits outstanding physical and chemical properties, making it a promising candidate for water treatment. We employed Car–Parrinello molecular dynamics simulations to establish accurate modeling of Na+ and Cl- permeation through hydrogen passivated nanopores in graphene and h-BN membranes. In these complex systems the classical potentials cannot properly account for the physics at play. We demonstrate that ion separation works well for the h-BN by imposing a barrier of 0.13 eV and 0.24 eV for Na+ and Cl- permeation respectively, compared to the graphene where the Cl- ion faces a negative barrier of 0.68 eV and is prone toward blockade and Na+ permeation is associated with a slightly negative barrier of 0.03 eV. From the change in the solvation shell, we get the following trend: Na/h-BN > Na/G > Cl/G > Cl/h-BN. We argue that the trend in the permeation barrier changes to Cl-h-BN > Na-h-BN > Na-G > Cl-G due to a combination of several interactions, including the distortion of the water network induced by the ions, the ion-water interaction, and the ion-nanopore interaction. Overall, the desalination performance of h-BN surpasses that of their graphene counterparts.

Surface acoustic wave (SAW) is effective for the manipulation of fluids and particles in microscale. The current approach of integrating interdigitated transducers (IDTs) for SAW generation into microfluidic channels involves complex and laborious microfabrication steps. These steps often require the full access to clean room facilities and hours to align the transducers to the precise location. This work presents an affordable and innovative method for fabricating SAW-based microfluidic devices without the need of clean room facilities and alignment. The IDTs and microfluidic channels are fabricated in the same process and thus precisely self-aligned in accordance with the device design. With the use of the developed fabrication approach, a few types of different SAW-based microfluidic devices have been fabricated and demonstrated for particle separation and active droplet generation.

Flavonoids are secondary plant metabolites involved in biological activity that are present in plentiful proportions in many plant origin foods and beverages. Owing to their chemical difference and qualities that make them beneficial for human health, they have received a lot of focus in research. This review therefore presents an account on the chemical structure of flavonoids, food sources and their metabolism with emphasis on bioavailability. And they also examine their antioxidant, anti-inflammatory, anticancer, cardiovascular protective, neuroprotective, and antimicrobial properties and reveal related molecular processes. In addition, it overviews the clinical data concerning their possible use in the prevention and treatment of chronic diseases. Some of the problems that attend current flavonoid research are also dealt with; such issues as variation in the bioactivity of flavonoids and scarcity of clinical studies. This review is designed to present current state of knowledge and to provoke further research concerning the further potential of flavonoids in enhancing human health.

The high performance of liquid chromatography(HPLC) has long been an indispensable tool for vigilance and analysis across range disciplines such as pharmaceuticals, environmental monitoring, food safety attributes etc. We will discuss about HPLC method development and validation, types of liquid chromatography methods focusing on proper use of a mobile phase like an eluent selection, how to optimize the conditions as well take it through its various procedures required for approval from regulatory bodies. Strategies to improve method robustness, sensitivity and reproducibility are highlighted. The future breakthroughs in HPLC technology and some innovative trends have also been speculated to limit this fundamental methodology.

Solanum indicum Linn, is commonly known as Indian Nightshade or Poison Berry belongs to the family Solanaceae. This review studied the botanical description, traditional uses of its seeds, its chemical composition, pharmacological properties and modern applications in medicinal system. The plant is rich in alkaloids, steroidal saponins, flavonoids and phenolic acids having diverse pharmacological activities and phytochemical profile. It is used in treatment of various respiratory disorders, inflammation, skin problems and gastrointestinal disease since ancient times. Scientific research in modern times also tested many of the traditional uses revealing anti-inflammatory, antioxidant, antimicrobial activities as well as some cytotoxic and even antidiabetic effects. These pharmacological activities show potential future as uses for organic drugs, natural health products, skincare formulations and agricultural advancements.

A new bisthiourea compound, 1,3,1',3'-(dinaphthalene-1,8-diyl)bisthiourea, was synthesized. Its structure was characterized by elemental analysis, FT-IR and 1H-, 13C-NMR and MS spectroscopic techniques.

A micro decision-making utility model under uncertainty is presented as a complementary foundation for macro coronavirus models. The micro model consists of two functions, a risk averse utility function depending on wellness and a wellness random output which is a function of the input variable called “treatment” consisting of such elements as social distance, washing hands, wearing a face mask, and others. The decision maker selects a level of treatment that maximizes her/his expected utility, given the probabilities of the respective outputs. The focus is on how changes in a person’s psychological attitude towards the macro determined (announced) probabilities affects the optimum results of the model. Such changes create a micro-macro dynamic interaction which is briefly outlined. A short discussion of the model’s behavioral implications for health policy is also given.

Non-conventional resonances, both acoustic and photonic, are found in metallic particles with a toroidal nanopropeller geometry that is generated by sweeping a three-lobed 2D-shape along a spiral with twisting angle, α. For both optical and acoustic cases, the spectral location of resonances experiences a red-shift as a function of α. We demonstrate that the optical case can be understood as a natural evolution of resonances as the spiral length of the toroidal nanopropeller increases with α, implying a huge helicity dependent absorption cross section. In the case of acoustic response, two red-shifting breathing modes are identified. Additionally, even a small α allows the appearance of new low-frequency resonances, whose spectral dispersion depends on a competition between length of the generative spiral and the pitch of the toroidal nanopropeller.

Coaches are the main people who have an impact on the mental and psychological performance of athletes as well as their physical performance. The purpose of this study is to investigate the effect of perceived coaching behaviors on the anger and aggression levels of male athletes. This study was conducted with 748 male athletes with an active license who are over 18 years of age and participate in individual and team sports branches. In this study, the "Coaching Behavior Assessment Ques-tionnaire" and the “Competitive Aggressiveness and Anger Scale" were used as data collection tools. The study results showed that athletes’ levels of evaluation of the coaching behaviors were high, while the levels of aggressiveness and anger in sports were low. It was determined that there is a negative low-level relationship between the athletes’ evaluation levels of the coaching be-haviors and the aggressiveness and anger levels in sports and that the coach’s behaviors predict the anger and aggressiveness levels of the athletes by 9% and 6%, respectively. The results of this study show that the attitudes and behaviors of coaches can affect the emotional states of male athletes and have the potential to increase or decrease their anger and aggressiveness levels. Coaches who exhibit positive, supportive, and modeling behaviors help create a healthy sports environment and help male athletes maintain emotional balance.

The açaí (Euterpe oleracea Mart.) is a native fruit of the Amazon that is well-known due to its commercial value. Its production chain is centered in the state of Pará, largely supplied by extractivism. The processing of açaí fruits in nature generates huge amount of solid waste, which can pose serious risks to the environment if not used and managed properly. Due to a small number of systhematic studies on the effect of chemical activation by pyrolysis of açaí seeds and fibers, and with the aim of providing a basis for future applications of the waste generated by processing of açaí fruits, the present work proposes a study of the pyrolysis of açaí seeds and fibers and the physicochemical and compositional characterization of the aqueous phase products. In this way, açaí seeds were collected from a local artisan processing facility in the city of Belém, PA. The seeds were dried at 105°C until constant weight, and subsequently, the fibers were separated from the seeds in a rotating drum. The seeds and fibers were impregnated with NaOH solutions at 0.5M, 1.0M, and 2.0M, and then pyrolyzed at a laboratory scale at 450 °C and 1 atm. The liquid products from pyrolysis were characterized through acidity index analysis, Fourier-transform infrared spectroscopy, and gas chromatography. The increase in the concentration of the impregnating agent resulted in an increase in bio-oil yield from both the seeds and fibers, rising from 3.3% (raw seeds) to 6.6% (seeds impregnated with 2M NaOH) and from 1.2% (raw fibers) to 3.7% (fibers impregnated with 2M NaOH). The yield in the aqueous phase after biomass pyrolysis showed an inverse behavior to the bio-oil yield, decreasing from 33.7% (raw fibers) to 21.2% (fibers impregnated with 2M NaOH) and from 41% (raw seeds) to 37.5% (seeds impregnated with 2.0M NaOH). High acidity levels were found in the aqueous phase samples and bio-oils derived from the seeds and fibers, which decreased as the concentration of the impregnating agent increased. The increase in the concentration of the impregnating agent (NaOH) influenced the chemical composition of the obtained liquid products, leading to a decrease in oxygenated compounds and an increase in nitrogenous compounds in both experimental matrices, which was also evidenced by the reduction in acidity.

Substantial research is required to ensure that micro-mobility ride sharing provides a better fulfillment of user needs. This study proposes a novel crowdsourcing model for the ride-sharing system where light vehicles such as scooters and bikes are crowdsourced. The proposed model consists of three entities: suppliers, customers, and a management party responsible for receiving, renting, booking, and demand matching with offered resources. It can allow suppliers to define the location of their private e-scooters/e-bikes and the period of time they are available for rent. Using a dataset of over 9 million e-scooter trips in Austin, Texas, we ran an agent-based simulation six times using three maximum battery ranges (i.e., 35, 45, and 60 km) and different numbers of e-scooters (e.g., 50 and 100) at each origin. Computational results show that the proposed model is promising and might be advantageous to shift the charging and maintenance efforts to a crowd of suppliers.

Açaí, a fruit from the Amazon, is valuable both economically and nutritionally. Its seeds, often discarded, can be transformed into bio-oil through pyrolysis (a thermochemical degradation process of residual biomass), providing a sustainable alternative to fossil fuels. This study investigates how temperature and molarity influence the antimicrobial, antioxidant, and cytotoxic activities of the produced bio-oil. Tests were conducted using Gas Chromatography-Mass Spectrometry (GC-MS) and assays to evaluate antimicrobial, antioxidant, and cytotoxic activities at different temperatures (350, 400, and 450 °C) and molarities (0.5 M, 1.0 M, and 2.0 M). Phenolic compounds were the most abundant in the bio-oil (55.70%), followed by cyclic and aromatic hydrocarbons (11.89%) and linear hydrocarbons (9.64%). Despite a reduction in oxygenated compounds, the bio-oil maintained bacteriostatic activity against Escherichia coli and Staphylococcus aureus across various temperature ranges, particularly at 350 °C. Antioxidant activity was highest at 350 °C and at lower molarities. Additionally, lower concentrations of acid impregnation exhibited cytotoxic effects at higher temperatures. Thus, bio-oil from açaí seeds produced via pyrolysis demonstrates potential for antioxidant and antimicrobial activities, suggesting viability for further testing at dilutions with lower cytotoxicity.

This study examines the negative impacts of dark stores on the urban environment from three perspectives: land use, transportation, and streetscape. It is conducted on B-Mart, a representative dark store in South Korea. First, in terms of land use, we find that dark stores that function as logistics facilities conflict with the surrounding land use. Second, by analyzing the location of dark stores and the hourly traffic volume of delivery vehicles, we find that the impact on the surrounding transportation infrastructure and pedestrian traffic is not as significant as previously claimed. However, during the transportation and loading process of the dark store, several problems such as traffic violations, illegal parking, and illegal loading were observed, posing a risk to nearby vehicles and pedestrians. Third, in terms of streetscapes, the location of dark stores on the ground floor of buildings can harm streetscapes. The current urban planning system in South Korea does not clearly define the status and function of dark stores, making it unclear how to manage them. Therefore, it is necessary to clarify their legal definition and introduce urban planning and design guidelines that are consistent with their appropriate location and appearance.

High-precision displacement sensing has been widely used across from both scientific researches and industrial applications. The recent interests in developing micro-opto-electro-mechanical systems (MOEMS) have given rise to an excellent platform for miniaturized displacement sensors. Advancement in this field during past years is now yielding integrated high-precision sensors which show great potential in applications ranging from photoacoustic spectroscopy to high-precision positioning and automation. In this review, we briefly summarize different techniques for high-precision displacement sensing based on MOEMS, and discuss the challenges for future improvement.

Objectives: Social distancing measures are currently implemented to control COVID-19 pandemic in many countries, including Saudi Arabia. The aim of this study was therefore to evaluate the awareness and adherence of the Saudi population to these measures. Methods: A web-based questionnaire was designed with 16 questions (8 questions related to demographics, 3 in relation to awareness about social distancing and 5 related to overall practice of social distancing). Results: 5105 participants completed the survey [58.4% female, 66.3% young individuals (aged 18-37 years), 55.8% bachelor degree holders, and 51.0% from the western region]. The Saudi Ministry of Health (MOH) was the main source of information about COVID-19 for most participants (78.2%). High awareness (81.3%) regarding social distancing was observed, associated mainly with female participants, those from the middle region and those with high education and income. Overall implementation of social distancing was satisfactory (score 3.13/5), with 37.8% never leaving home during the home-stay period. Better adherence to social distancing was observed for female participants, higher degree holders and those aged over 38 years. Conclusions: Organised plans by the Saudi MOH have been effective in raising awareness and improving practice of social distancing among public. However, the observed lower practice of social distancing by individuals with lower education and income indicates the need for targeted interventions to achieve better outcome.

This study measures the technical and scale efficiency of Micro and Small Enterprises (MSEs) and input slacks using Data Envelop Analysis (DEA) model and identifies the determinants of efficiencies of MSEs by employing ordinary least square (OLS) econometrics model. A sample of 375 randomly selected MESs are included in the study. The study found that the average technical and scale efficiency of MSEs are relatively low; technical efficiency averaged at 30 percent and 38.4 percent under constant returns to scale (CRS) and variable returns to scale (VRS) assumptions, respectively. Besides, the overall average scale efficiency score of MSEs was estimated at 77.8 percent. The highest mean technical and scale efficiencies were registered in the construction (71.8 percent) and manufacturing (85.7 percent) sectors, respectively. Whereas, the lowest technical and scale efficiency goes to urban agriculture sector and service sector, with 38.9 percent and 67.2 percent, respectively. The level of inputs, enterprise age and sector, human capital, labor productivity variables significantly affect relative technical efficiency level of MSEs with different directions while variables such as start-up capital, gender of the enterprise manager and availability of support from the government identified statistically not significant in determining the MSEs’ technical efficiency.

Aim: Ovarian cancer is the leading cause of gynecological cancer deaths worldwide. Treatment methods are listed as surgery, chemotherapy and radiotherapy depending on the stage of the cancer, but developing resistance to chemotherapy increases the need for alternative agents that act on the same pathways. In this study, the effects of rosmarinic acid (RA) and doxorubicin (DX) on the activation of FOXP3, an important tumor suppressor gene, in OVCAR3 cells were examined. Material Method: In the study, human ovarian adenocarcinoma cell line was used. MTT test was applied to determine the effect of rosmarinic acid and doxorubicin on the proliferation of OVCAR3 cells. Expression levels of FOXP3 for cell proliferation and Capase-3 for Apoptosis were determined by qRT-PCR and Western blot analysis. Wound healing model was applied to determine metastasis. The results were evaluated with one-way ANOVA in SPSS 20.0 program as p≤0.05. Results: It was determined that rosmarinic acid alone and in combination with doxorubicin inhibited the proliferation of OVCAR3 cells in a time- and dose-dependent manner for 24, 48 and 72 hours, and caused the cells to die by causing them to undergo apoptosis. It was observed that Caspase-3 expression increased approximately tenfold in OVCAR3 cells, while FOXP3 expression increased only in RA treatment and was downregulated in DX and RA+DX treatments. Coclusion According to the results of our study, it was observed that many steps of the signaling pathways related to proliferation, migration and apoptosis were affected by the combination of RA and DX in OVCAR3 cells. This shows that RA will gain an important place in cancer treatment with more comprehensive studies.

Aim: Ovarian cancer is one of the most frequently diagnosed cancers in women in the world. Recognition of the differences between tumors in cancers and resistance to treatment in patients have made the treatment potential of chemotherapy, radiotherapy and immunotherapy controversial. Especially against drug resistance, laboratories have implemented the drug diversion system by putting old drugs into new forms. In this study, the cytotoxic and apoptotic effects of the combination of doxorubicin (DX) and thymoquinone (TQ) on ovarian adenocarcinoma cells (OVCAR3) were investigated. Material Method: OVCAR3 cell line was cultured in RPMI medium containing 10% FBS, 1% penicillin/streptomycin. Cell viability and cell growth rate were determined by MTT viability test by combining doxorubicin and thymoquinone. Nucblue immunofluorescent staining was used to determine the mechanism of cell death at different doses of doxorubicin and thymoquinone compounds, qRT-PCR to determine the pathways underlying the apoptotic mechanism, and western blot methods to show protein levels. Result: We found that the combination of DX and TQ reduced the viability of OVCAR3 cells (MTT assay), induced apoptosis (RAF, RAS, Bcl2, Bax by qRT-PCR) and increased RAF, RAS protein levels in TQ and DX-treated cells by western blot analysis. Conclusion: The results obtained revealed for the first time that combining DX and TQ also had cytotoxic/apoptotic and anti-proliferative effects against ovarian adenocarcinoma cells.

Secondary microplastic (MPL) and nanoplastic (NPL) particles exhibit different physiochemical characteristics that attenuate their toxicities in different ways: some particle types being well documented (primary) while other (secondary), are more unknown. Fourier Transform Infrared Spectroscopy (FTIR), Raman, Proton Nuclear Magnetic Resonance (H-NMR), Curie Point-Gas Chromatography-Mass Spectrometry (CP-gc-MS), Induced Coupled Plasma-Mass Spectrometry (ICP-MS), Nanoparticle Tracking Analysis (NTA), Field Flow Fractionation-Multiple Angle Light Scattering (FFF-MALS), Differential Scanning Calorimetry (DSC), Thermogravimetry (TGA), Differential Mobility Particle [Sizing] (DMPS), Scanning Electron Microscopy (SEM), Transmission Electron Microscopy (TEM), and Scanning Transmission X-ray Microspectroscopy (STXM) are re-viewed as part of a suite of characterization methods for physiochemical ascertainment and distinguishment. Organizations, like the water treatment or waste management industry, and those in groups that bring awareness to this issue, which are in direct contact with the hydrosphere, can utilize these techniques in order to sense and remediate this plastic polymer pollution. The primary goal of this review paper is to highlight the extent of plastic pollution in the environment as well as introduce its effect on the biodiversity of the planet while underscoring current characterization techniques in this field of research. The secondary goal involves illustrating current and theoretical avenues in which future research needs to address and optimize MPL/NPL remediation, utilizing nanotechnology, before this sleeping giant of a problem awakens.

The expansion of concrete subjected to extreme elevated temperature is linked with intricate micro-structural variations, such as the transformation of the constituent phases. This study proposes a model to predict the thermal expansion of cement paste and concrete considering micro-structural changes under elevated temperatures ranging from 20°C to 800°C. The model presented can consider characteristics of various aggregates in the calculation of thermal expansion for concrete. The model is a combination of a multi-scale stoichiometric model and a multi-scale composite model. At the cement paste level, the model satisfactorily predicted a test result. At concrete level, upper bounds from the model were matched relatively well with test results by previous researcher. If the mechanical properties, such as elastic modulus (E), Poisson’s ratio (ν), and thermal deformation, of the aggregates used in concrete are given, it is likely that the model will reasonably predict experimental results.

Microscopic vision plays an important role in automated micro-assembly. However, some uncertain factors in the assembly process, such as occlusion and stains can lead to the mistakes of feature extraction. Herein, to solve the problem, the deep learning techniques are introduced into the feature recognition tasks, focusing on the attention mechanism and visualizing CNNs for DL-based microscopic vision. The main contributions are summarized as follows: The CBAM attention mechanism is combined with the YOLOv5 algorithm to improve the accuracy and robustness of feature extraction. The micropart feature occlusion experiment results show that at 70% occlusion degree, YOLOV5-CBAM can reach 97.9% [email protected], which is 4.6% higher than the original one. Visualization analysis of DL-based model is conducted using Grad-CAM to make the decision result more transparent and avoid potential visual detection risks during assembly. The heatmap matching degree between GT area and high-light area is increased by 27.81% on average, which further verify the effectiveness of attention mechanism in micropart feature localization. Additionally, micropart surface stain and droplet quality classification models based on ResNet50 are trained to replace the manual sorting. The visual results are consistent with human eye discernment and judgement, confirming the reliability of parts and droplets sorting.

Potocki-Lupski Syndrome (PTLS) is a rare condition associated with a duplication of 17p11.2 that may underlie a wide range of congenital abnormalities and heterogeneous behavioral phenotypes. Along with developmental delay and intellectual disability, autism-specific traits are often reported to be the most common among patients with PTLS. To contribute to the discussion of the role of autism spectrum disorder (ASD) in the PTLS phenotype, we present a case of a female adolescent with a de novo dup(17)(p11.2p11.2) without ASD features, focusing on in-depth clinical, behavioral, and electrophysiological (EEG) evaluations. Among EEG features, we found the atypical peak-slow wave patterns and a unique saw-like sharp wave of 13 Hz that was not previously described in any other patient. The power spectral density of the resting state EEG was typical in our patient with only the values of non-linear EEG dynamics: Hjorth complexity and Fractal dimension were drastically attenuated compared with the patient’s neurotypical peers. Here we also summarize results from previously published reports of PTLS that point to the about 21% occurrence of ASD in PTLS that might be biased, taking into account methodological limitations. More consistent among PTLS patients were intellectual disability and speech and language disorders.

The development of a rapid, sensitive, specific method for detecting foodborne pathogens is paramount in supplying safe food to enhance public health safety. Despite the significant improvement in pathogen detection methods, key issues are still associated with rapid methods, such as distinguishing living cells from dead, pathogenic potential or health risk of the analyte at the time of consumption, detection limit, and sample-to-result. The mammalian cell-based assays analyze pathogens' interaction with the host cells and are responsive to only live pathogens or active toxins. In this study, a human embryonic kidney (HEK293) cell line expressing Toll-Like Receptor 5 (TLR-5) and chromogenic reporter system (HEK dual hTLR5) was used for the detection of viable Salmonella in a 96-well tissue culture plate. This cell line responds to low concentrations of TLR5 agonist flagellin. Stimulation of TLR5 ligand activates nuclear factor-kB (NF-κB) - linked alkaline phosphatase (AP-1) signaling cascade inducing the production of secreted embryonic alkaline phosphatase (SEAP). With the addition of a ρ-nitrophenyl phosphate as a substrate, a colored end product representing a positive signal is quantified. The assay's specificity was validated with the top 20 Salmonella enterica serovars and 19 non-Salmonella spp. The performance of the assay was also validated with spiked food samples. The total detection time (sample-to-result), including shortened pre-enrichment (4 h) and selective enrichment (4 h) steps with artificially inoculated outbreak-implicated food samples (chicken, peanut kernel, peanut butter, black pepper, mayonnaise, and peach) was 15 h when inoculated at 1–100 CFU/25 g sample. These results show the potential of HEK-DualTM hTLR5 cell-based functional biosensors for rapid screening of Salmonella.

This paper is referred to a top frontline research in life science, showing that in spite of the large variation of the physiological architecture and behavioral forms of the living systems, the fundamental structure of their informational system is basically the same, allowing the body growth/development by micro to macro-structuration processes, maintaining the same informational configuration and functions like the basic unit of life – the eukaryotic cell. Starting and based on the determination of the special/specific info-operability in living structures and the role of information in structuration and their functionality, there are discussed the informational functions of the eukaryotic/prokaryotic cells, the simplest units of life and is elaborated and presented the Informational Model of the Living Structures, showing that these structures operate on the basis of two main informational systems: one of them defined as the Programmed Informational System, composed by three components, assuring respectively the info-generation, maintenance and the proliferation/reproduction, and another one defined as the Operative Informational System, necessary for the continuous communication with the environment for adaptation, consisting in four main components referred to memory, decision, sentience and info-connection/info-selection. The revealed properties are compared with the Informational System of the Human Body, as a prototype of a living system on the top of the evolutionary scale, showing/demonstrating the compatibility of structuration and functions on the entire scale, from prokaryotic/eukaryotic unit cells to multicellular organisms – plants, animals and human, by means of a continuous adaptation process, which always follows the same line of micro to macro-structuration process based on the same Info-organization and functionality. These models are new and revolutionary in the information and life sciences

The ability to detect the presence as well as classify the activities of individuals behind visually obscuring structures is of significant benefit to police, security and emergency services in many situations. This paper presents the analysis from a series of experimental results generated using a through-the-wall (TTW) Frequency Modulated Continuous Wave (FMCW) C-Band radar system named Soprano. The objective of this analysis was to classify whether an individual was carrying an item in both hands or not using micro-Doppler information from a FMCW sensor. The radar was deployed at a standoff distance, of approximately 0.5 m, outside a residential building and used to detect multiple people walking within a room. Through the application of digital filtering, it was shown that significant suppression of the primary wall reflection is possible, significantly enhancing the target signal to clutter ratio. Singular Value Decomposition (SVD) signal processing techniques were then applied to the micro-Doppler signatures from different individuals. Features from the SVD information have been used to classify whether the person was carrying an item or walking free handed. Excellent performance of the classifier was achieved in this challenging scenario with accuracies up to 94%, suggesting that future through wall radar sensors may have the ability to reliably recognize many different types of activities in TTW scenarios using these techniques.

The spread of micro- (MPs) and nanoplastics (NPs) in the environment has become a significant environmental concern, necessitating effective removal strategies. In this comprehensive scientific review, we examine the use of magnetic nanoparticles (MNPs) as a promising technology for the removal of MPs and NPs from water. We first describe the issue of MPs and NPs and their impact on the environment and human health. Then the fundamental principles of using MNPs for the removal of these pollutants will be presented, emphasizing that MNPs enable selective binding and separation of MPs and NPs from water sources. Furthermore, we provide a short summary of various types of MNPs that have proven effective in the removal of MPs and NPs. These include ferromagnetic nanoparticles, MNPs coated with organic polymers, as well as nanocomposites and magnetic nanostructures. We also review their properties, such as magnetic saturation, size, shape, surface functionalization and stability, and their influence on removal efficiency. Next, we describe different methods of utilizing MNPs for the removal of MPs and NPs. We discuss their advantages, limitations, and potential for further development in detail. In the final part of the review, we provide an overview of existing studies and results demonstrating the effectiveness of using MNPs for the removal of MPs and NPs from water. We also address challenges that need to be overcome, such as nanoparticle optimization, process scalability, and the removal and recycling of nanoparticles after the completion of the process. This comprehensive scientific review offers an extensive insight into the use of MNPs for the removal of MPs and NPs from water. With improved understanding and the development of advanced materials and methods, this technology can play a crucial role in addressing the issue of MPs and NPs and preserving a clean and healthy environment.

Candida albicans is an opportunistic fungus that becomes pathogenic and problematic under certain biological conditions. C.albicans may cause painful and uncomfortable symptoms, as well as deaths in immunocompromised patients. Therefore, early detection of c.albicans is essential. However, conventional detection methods are costly, slow and inaccessible to women in remote or developing areas. To address these concerns, we have developed a wearable and discrete naked-eye detectable, colorimetric platform for c.albicans detection. With some modification, this platform is designed to be directly adhered to existing feminine hygiene pads. Our platform is rapid, inexpensive, user-friendly, disposable and only requires three steps: i) addition of vaginal fluid onto sample pads; ii) addition of gold nanoparticle gel and running buffer, and iii) naked eye detection. Our platform is underpinned by selective thiolated aptamer-based recognition of 1,3-β-D glucan molecules- a hallmark of c.albicans cell walls. In the absence of c.albicans, wearable sample pads turn bright pink. In the presence of c. albicans, the wearable pads turn dark blue due to significant nanoparticle target-induced aggregation. We demonstrate naked eye colorimetric detection of 4.4 ×106 c.albicans cells per ml. We believe that this proof-of-concept platform has the potential to have a significant impact on women’s health, globally.

Ti and its alloys are the most commonly used materials for biomedical applications. However, bacterial infection after implant placement is still one of the significant rising complications. Therefore, the application of the antimicrobial agents into implant surfaces to prevent implant-associated infection has attracted lots of attention. Scientific papers have shown that inorganic antibacterial metal element (e.g. Ag, Cu, Zn) can be introduced to implant surfaces with the addition of metal nanoparticles or metallic compounds into electrolyte via micro-arc oxidation (MAO) technology. In this review, the effects of the composition and concentration of electrolyte and process parameters (e.g. voltage, current density, oxidation time) on morphological characteristics (e.g. surface morphology, bonding strength), antibacterial ability and biocompatibility of MAO antimicrobial coating were discussed in detail. Anti-infection and osseo-integration can be simultaneously accomplished with the selection of the proper antibacterial elements and operating parameters. Besides, MAO assisted by magnetron sputtering (MS) to endow Ti-based implant materials with superior antibacterial ability and biocompatibility was also discussed. Finally, the development trend of MAO technology in the future was forecasted.

The objective of the study was to analyse the antimicrobial susceptibility trends of Spanish porcine bacteria to quinolones, cephalosporins and polymyxins. Isolates of Actinobacillus pleuropneumoniae, Pasteurella multocida, and Escherichia coli were isolated from sick pigs from 2019 to 2022. Antimicrobial susceptibility test was determined by minimal inhibitory concentration (MIC) following internationally accepted methodology. MIC categorization was based on distributing the range of MIC values in four categories being category one the most susceptible (lowest MIC value) and four the less susceptible one (highest MIC value). Moreover, clinical susceptibility (susceptible/resistant) was also determined according to CLSI and EUCAST clinical breakpoints. A logistic and multinomial logistic regression model was used to analyze the susceptibility data for dichotomized and categorized MIC data, respectively for any pair of antimicrobial/microorganism. In general terms, the antimicrobial susceptibility of pig bacteria to these antimicrobials remained stable or increased in the last four years in Spain. In the case of A. pleuropneumoniae and quinolones, it was observed a significant temporal trend where isolates from 2020 had significantly increased odds of being more susceptible than isolates from 2019. In the case of E. coli and polymyxins, a significant temporal trend was observed where isolates from 2020 and 2021 had significantly increased odds of being more susceptible than isolates from 2019 and 2020, respectively. Finally, a significant odd of being less susceptible was only observed for cephalosporins and E. coli for 2020 versus 2019, stagnating for the rest of study period. These results provide sound data on critical important antimicrobials in swine medicine.

Energy from biogas is one of the most promising renewable energy sources. Significant, for technical, economic, and environmental reasons, is the construction of agricultural microgas plants next to households specialising in cattle rearing. The availability of free substrate makes it possible not only to produce one's electricity and heat but also to produce a more environmentally and human-friendly manure. The operation of biogas plants is, unfortunately, associated with technical problems. This paper presents the results of a study of the quality of electricity generated in an agricultural biogas plant built at a farm specialising in dairy cows, where the owner reported a problem with the voltage in the power supply network. Therefore, selected power quality parameters occurring at the connection point of the biogas plant were analysed in detail. As the authors' research showed, in the case in question, the agricultural biogas plant was connected via a cable with too small a conductor cross-section, which resulted in significant voltage exceedances, making it impossible to switch on the second of the biogas plant's generators. Replacement of the feed-in cable has enabled both generators to run, but significant fluctuations in the feed-in voltage values were still noticeable. Analysis of the subsequent measurements revealed the need for changes in the design of the digester itself. The proposal for change is to replace the two current digester mixers (each rated at 9 kW) with more mixers of lower power. The new mixers would operate in an alternating system, where only one would always be activated.

Based on the need for real-time sag monitoring of Overhead Power Lines (OPL) for electricity transmission, this article presents the implementation of a hardware and software system for online monitoring of OPL cables and cable sag determination. The mathematical model based on differential equations and the methods of algorithmic calculation of OPL cable sag are presented. Considering that, based on the mathematical model presented, the calculation of OPL cable sag can be done in different ways depending on the sensors used, and the presented application uses a variety of sensors. Therefore, a direct calculation is made using one of the different methods. Subsequently, the verification relations are highlighted directly and, respectively, the calculation by the alternative method, which uses another group of sensors, to generate both a verification of the calculation and the functionality of the sensors, thus obtaining a defect observer of the sensors. The hardware architecture of the OPL cable online monitoring application is presented, together with the main characteristics of the sensors and communication equipment used. The configurations required to transmit data using the ModBUS and ZigBee protocols are also presented. The main software modules of the OPL cable condition monitoring application are described, which ensure the monitoring of the main parameters of the power line and the visualisation of the results both on the electricity provider's intranet using a web server and MySQL database, and on the Internet using an Internet of Things (IoT) server. This categorisation of the data visualisation mode is done in such a way as to ensure a high level of cyber security. Starting from the mathematical model of the OPL cable sag calculation, it goes through the stages of creating such a monitoring system, from the numerical simulations carried out using Matlab to the real-time implementation of this monitoring application. The main modules of the application software are: the software module for reading quantities from the sensor network through a ModBUS Input/Output (I/O) server, the software module for real-time calculation of the OPL cable sag, the software module for read/write operations based on MySQL type data, the software module for transferring data to the user's intranet through a web server, and the software module for viewing data by authorised users based on user and password through an IoT server. The development software environments used are Matlab and Laboratory Virtual Instrument Engineering Workbench (LabVIEW).

GaN ultraviolet photodetector with metal-semiconductor-metal structure is achieved by growing on a periodic trapezoid column-shape patterned sapphire substrate using metalorganic chemical vapor deposition. Under 5-V reverse bias, the photodetector fabricated on such patterned sapphire substrate exhibits a lower dark current, a higher photocurrent, and a 476 % enhancement in the maximum responsivity as compare with those of the photodetector fabricated on conventional flat sapphire substrate. It is also found that the much larger UV-to-visible rejection ratio and the fact that responsivity drops in a smaller cut-off region are observed from photodetector fabricated by using a periodic trapezoid column-shape patterned sapphire substrate. These phenomena may all be attributed to the reduction of threading dislocation density and the improved quality of GaN film, as well as the internal reflection and/or scattering effect on the interface between GaN film and the periodic trapezoid column-shape pattern of the substrate.

Microstructured surfaces are renowned for their unique properties, such as waterproofing and low adhesion, making them highly applicable in the biomedical field. These surfaces play a crucial role in influencing cell response by mimicking the native microenvironment of biological tissues. In this study, we engineered a series of biomimetic micropatterned surfaces using polydimethylsiloxane (PDMS) to explore their effects on primary breast cancer cell lines, contrasting these effects with those observed on conventional flat surfaces. The surface topography was varied to direct cells’ attachment, growth, and morphology. Our findings elucidate that surface-free energy is not merely a background factor but plays a decisive role in cell dynamics, strongly correlating with the spreading behaviour of breast cancer cells. Notably, on micropillar surfaces with high surface-free energy, an increase in the population of cancer cells was observed. Conversely, surfaces characterised by lower surface-free energies noted a reduction in cell viability. Moreover, the structural parameters, such as the gaps and diameters of the pillars, were found to critically influence cellular dispersion and adherence, underscoring the importance of the microstructures’ topography in biomedical applications. These insights pave the way for designing advanced microstructured surfaces tailored to specific cellular responses, opening new avenues for targeted cancer therapies and tissue engineering.

Recent discoveries of potential ice particles and ice-cemented regolith on celestial bodies like the Moon and Mars have ushered in new opportunities for developing technologies to extract water, facilitating future space missions and activities on these celestial surfaces. This study delves into the potential for water extraction from regolith through an experiment designed to test water recuperation from regolith simulant under varying gravitational conditions. The resultant water vapor extracted from the regolith is re-condensed on a substrate surface and collected in liquid form. Three types of substrates, hydrophobic, hydrophilic, and grooved, are explored. The system’s functionality was assessed during a parabolic flight campaign simulating three distinct gravity levels: microgravity, lunar gravity, and Martian gravity. Our findings reveal that the hydrophobic surface demonstrates the highest efficiency due to drop-wise condensation, and lower gravity levels result in increased water condensation on the substrates. This experiment aims to provide insights into in-situ water recovery, which is pivotal for establishing economically-sustainable water supplies for future missions.

The concept of intelligence has many applications, such as coatings and cyber security. Smart coatings have the ability to sense and/or response to external stimuli and generally interact with their environment. Self-healing coatings represent a significant advance in improving material durability and performance using microcapsules and nanocontainers loaded with self-healing agents, catalysts, corrosion inhibitors, and water-repellents. These smart coatings can repair damage on their own and restore mechanical properties without external intervention and are inspired by biological systems. Properties that are affected by either momentary or continuous external stimuli in smart coatings can be related to corrosion, fouling, fungal, self-healing, pie-zoelectric, microbiological, etc. These coating properties can be obtained via combinations of either organic or inorganic polymer phases, additives and pigments. In this article, a review on the advancements of micro/nanocapsules for self-healing coatings is reported from the aspect of ex-trinsic self-healing ability. The concept of extrinsic self-healing coatings is based on the use of capsules or multichannel vascular systems loaded with healing agents/inhibitors. The outcome is that self-healing coatings exhibit improved properties compared to traditional coatings. It is mentioned that self-healing anticorrosive coating not only has enhanced passive barrier function, but also realizes active defense. As a result, there is a significant improvement of the service life and overall performance of the coating. Future research should be devoted to refining self-healing mechanisms and developing cost-effective solutions for a wide range of industrial applications.

We investigated the micro-threaded stem taper surface and the impact on premature failures, aseptic loosening, and infection. We have focused on the fretting, and crevice corrosion of micro-threaded tapers, as well as the characterization of microstructure and surface properties of two new and three retrieved Zweymüller stem tapers of cementless hip endoprostheses selected from a set of 45 stems. The retrievals examined were those in which the sole source of modularity with a metallic component was the head-stem taper interface between the Ti alloy taper stem and the ceramic head. To determine the surface chemistry and microstructures of both new and retrieved hip endoprostheses stem taper titanium alloy, scanning electron microscopy (SEM) was employed for morphological and microstructural analyses. At the same time, energy dispersive spectroscopy (EDS) was utilized for characterizing chemical element distribution, and electron backscattered diffraction (EBSD) was used for phase analysis. The micro-threated stem taper’s roughness for different manufacturers was investigated using an optical profilometer. Standard roughness pa-rameters Ra (average surface roughness) and Rz (mean peak to valley height of the roughness pro-file) were used in this investigation.Additionally, profile depth and peak spacing for different samples were investigated. The surface roughness results indicate no significant difference in roughness associated with varying survivorship times, ranging from 3 to 239 months, and across different manufacturers. Electrochemical studies revealed no fretting corrosion in retrieved stem tapers (ceramic head) that prematurely failed due to aseptic loosening after 239 months, infection after 3 months, and low-grade infection after a 32-month lifetime. Therefore, three retrieved ta-pers and two new ones for comparison underwent potentiodynamic measurements in Hank’s so-lution to ascertain the corrosion rate of new and retrieved stem taper surfaces. The results show a low corrosion rate for both new and retrieved samples that failed prematurely due to aseptic loosening. However, the corrosion rate of infected and low-grade infected tapers was higher. In conclusion, our study aligns with existing literature, suggesting that the use of ceramic heads de-creases the problem of taper corrosion and subsequently reduces premature failures in total hip arthroplasty.

Hydrogen sulfide is present in active or extinct volcanic areas (mofettas). The habitable premises in these areas are affected by the presence of hydrogen sulfide, which, even in low concentrations, gives off a bad to unbearable smell. If the living spaces considered are closed enclosures, then a system can be designed to reduce the concentration of hydrogen sulfide. This paper presents a membrane way to reduce the hydrogen sulfide concentration to acceptable limits using a cellulosic derivative-propylene hollow fiber based composite membrane module. The cellulosic derivatives considered were carboxymethyl–cellulose (NaCMC), cellulose acetate (CA), methyl 2–hydroxyethyl–cellulose (MHEC), and 2–hydroxyethyl–cellulose (HEC). In the permeation module, hydrogen sulfide is captured with a solution of cadmium that forms cadmium sulfide, usable as a luminescent substance. The composite membranes were characterized by SEM, EDAX, FTIR, FTIR 2D maps, thermal analysis (TG and DSC) and from the perspective of hydrogen sulfide air removal performance. To determine the process performances, the variables were: the nature of the cellulosic derivative–polypropylene hollow fiber composite membrane, the concentration of hydrogen sulfide in the polluted air, the flow rate of polluted air, and the pH of the cadmium nitrate solution. Pertraction efficiency was maximum for the sodium carboxymethyl–cellulose (NaCMC)-polypropylene hollow fiber membrane, a hydrogen sulfide concentration in the polluted air of 20 ppm, polluted air flow rate of 50 L/min, and a pH of 2 and 4.

The purpose of this study is to examine the driving model of determinant factors that affects the performance of small and micro enterprises empirical evidence from Amhara Region, Ethiopia. The study used primary and secondary data from manufacturing, construction, urban agriculture, trade, and service entrepreneurs found in Bahirdar, Dessie & Gonder Cities using a purposive sampling technique. It also used the descriptive research design with a self-administered survey questionnaire. The Statistical analysis tools, SPSS and Amos, software were applied to analyze the data. Multiple regression model results revealed that access to credit, initial capital, working premises, industry category, market linkage, ICT adoption have a positive relationship and a major impact on the Amhara region's enterprise performance. Hence, the outcome variable, enterprise performance, is highly affected by all predicted variables. As the study finding shows, a lack of access to credit, , market linkage, working premises), initial capital, and information communication Technology problems are critical challenges of SMEs. The Regional Government, TVED Bureau, Micro Finance Institutions, , should take corrective action to provide sufficient credit and long-term loans to protect inflation. Moreover, this study proposed a sustainable cluster management approach that solves their challenges in an integrated way.

The purpose of this study is to examine the driving model of determinant factors that affects the performance of small and micro enterprises empirical evidence from Amhara Region, Ethiopia. The study used primary and secondary data from manufacturing, construction, urban agriculture, trade, and service entrepreneurs found in Bahirdar, Dessie & Gonder Cities using a purposive sampling technique. It also used the descriptive research design with a self-administered survey questionnaire. The Statistical analysis tools, SPSS and Amos, software were applied to analyze the data. Multiple regression model results revealed that access to credit, initial capital, working premises, industry category, market linkage, ICT adoption have a positive relationship and a major impact on the Amhara region's enterprise performance. Hence, the outcome variable, enterprise performance, is highly affected by all predicted variables. As the study finding shows, a lack of access to credit, , market linkage, working premises), initial capital, and information communication Technology problems are critical challenges of SMEs. The Regional Government, TVED Bureau, Micro Finance Institutions, , should take corrective action to provide sufficient credit and long-term loans to protect inflation. Moreover, this study proposed a sustainable cluster management approach that solves their challenges in an integrated way.

The objective of this study is to evaluate the effects of the 3D point cloud density derived from unmanned aerial vehicle (UAV) photogrammetry and structure from motion (SfM) and multi-view stereopsis (MVS) techniques, the interpolation method for generating a digital terrain model (DTM), and the resolution (grid size) of the derived DTM on the accuracy of estimated heights in small areas, where a very accurate high spatial resolution is required. A UAV-photogrammetry project was carried out on a bare soil of 13 × 13 m with a rotatory wing UAV at 10 m flight altitude (equivalent ground sample distance = 0.4 cm). The 3D point cloud was derived, and five sample replications representing 1, 2, 3, 4, 5, 10, 15, 20, 30, 40, 50, 60, 70, 80 and 90% of the original cloud were extracted to analyze the effect of cloud density on DTM accuracy. For each of these samples, DTMs were derived using four different interpolation methods (Inverse Distance Weighted (IDW), Multiquadric Radial Basis Function (MRBF), Kriging (KR), and Triangulation with Linear Interpolation (TLI)) and 15 DTM grid size (GS) values (20, 15, 10, 9, 8, 7, 6, 5, 4, 3, 2, 1, 0.67, 0.5, and 0.4 cm). Then, 675 DTMs were analyzed. The results showed, for each interpolation method and each density, an optimal GS value (most of the cases equal to 1 cm) for which the Root Mean Square Error (RMSE) is minimum. IDW was the interpolator which yielded best accuracies for all combination of densities and GS. Its RMSE, considering the raw cloud, was 1.054 cm. The RMSE increased 3% when a point cloud with 80% extracted from the raw cloud was used to generate the DTM. When the point cloud included the 40% of the raw cloud, RMSE increased 5%. For densities lower than 15%, RMSE increased exponentially (45% for 1% of raw cloud). The grid size minimizing RMSE for densities of 20% or higher was 1 cm, which represents 2.5 times the ground sample distance of the pictures used for developing the photogrammetry project.

Due to their wide range of uses in modern technology, nanomaterial’s of silver metallic (Ag-NPs) have engaged considerable concern, driving significant research with development efforts. This study focuses on investigating the antimicrobial properties of Ag-NPs, encompassing their production, characterization, and biological aspects. The eco-friendly extracellular biosynthetic method employed in this work utilized extracts from the marine fungus Aspergillus flavus MK4 as reducing agents for nanoparticle synthesis. Analyzing the colloidal Ag-NPs using UV-visible spectroscopy revealed a peak in absorbance at 460 nm, indicating the presence of plasmonic properties. The electrons imaging of internal structure (TEM) elucidated spherical shape of the Ag-NPs by 15 nm size. Testing against bacterial diversities (Gr-ve & Gr+ve) revealed potent antibacterial and antifungal efficacy. Cytotoxicity versus HepG-2 cell line was assessed using the MTT assay, and antioxidant properties were examined through the radical scavenging (DPPH) assay. In wise of their conceivable applications in the fields of antibacterial, anticancer, and wound-healing, the Ag-NPs that were synthesized exhibit promising features. With its powerful ability to synthesize silver nanoparticles (Ag-NP), Aspergillus flavus MK4 Aspergillus flavus MK4 can generate nanoparticles extensively characterized, demonstrating their antibacterial, antioxidant, anticancer, and wound-healing properties.

In this paper, we present an experimental procedure to enhance the dimensional accuracy of fabrication via Stereolithography (SLA) of features at the micro-scale. Using a custom benchmark part, deviations in feature dimensions (micro-pores diameters and depths) were detected and measured by confocal microscopy. Samples characterization and experimental observations allowed the identification of inaccuracy sources, mainly due to the laser beam scanning strategy and to the incomplete removal of uncured liquid resin in post-processing (i.e., IPA washing). As a technology baseline, the measured dimensional errors on pores diameters were up to -46%. A compensation method of the nominal laser spot diameter (85m) was defined and implemented resulting in relevant improvements in dimensional accuracy of 9.8% and 11.3% on full-open pores diameter and depth, respectively. Further investigation was performed on a customized test part to adjust the calibration procedure. The measurements revealed that the estimate of the laser beam spot size is 968m. Measurements on micro-pores having different sizes revealed that a constant compensation parameter (i.e., C=85, 96, 120m) is not fully effective at the micro-scale, where average errors still remain at -24%, -18.8%, and -16% for compensations equals to 85, 96 and 120m, respectively. A further experimental campaign allowed the identification of an effective nonlinear compensation law where the compensation parameter depends on the micro-feature size C= f (D). Results show a sharp improvement in dimensional accuracy on micro-pore fabrication, with errors consistently below +8.2%. The proposed compensation method can be extended for the fabrication of any micro-features without restrictions on the specific technology implementation. Concerning the inaccuracy introduced by the laser path, experimentation with a customized part allowed the optimization of the part orientation to reduce the errors and their differences along the X and Y machine axes.

Pure titanium is limited to be used in biomedical applications due to its lower mechanical strength compared to its alloy counterpart. To enhance its properties and improve medical implants feasibility, advancements in titanium processing technologies are necessary. One such technique is equal channel angular pressing (ECAP) for its severe plastic deformation (SPD). This study aimed to surface modify commercially pure titanium using micro arc oxidation (MAO) technology and mineral solutions containing Ca and P. The composition and shape of the changed surface were characterized using X-ray diffraction (XRD) and scanning electron microscope (SEM), respectively. The weight % of Ca and P in the coating was determined using Energy Dispersive Spectroscopy (EDS), and the corrosion resistance was evaluated through potentiodynamic measurement. The behavior of human dental pulp cell and periodontal cell behavior was also studied through a biomedical experiment over a period of 1-, 3-, and 7-days using trypsin as the culture medium and ELISA as the observation method. This study showed that the mechanical grain refinement method and surface modification significantly improved the biomechanical properties of commercially pure (CP) Titanium. Although the results showed variations in the absorbance values of cells cultured on different surfaces, this study provides valuable insights into pulp cell behavior and advances the field of biomedical research.

The main purpose of this work was to tests of form and size of fatigue wear of the top layer of oil gear pump wheel (3PW-BPF-24). The object of tests was operated during a determined number of hours at strictly controlled operational and environmental parameters. A microscope of focal differentiation by Alicona InfiniteFocus G4 (with Focus-Variation optical measuring technology) was used for an identification, measurement and description of noticed superficial defects, which resulted from the fatigue process of the top layer and an earlier thermochemical treatment. The work was finished with an analysis of obtained results (based on the analysis of 3D scans) and conclusions concerning about optimization of the thermal treatment. Taking into consideration the presented results (suggestions) in the technology of improving strength properties of gear wheels (of this type oil pumps) may render it possible to obtain an appropriate fatigue endurance of the top layer, i.e. a minimization of observed superficial defects.

Açai is a fruit common in the northern region of Brazil, and its consumption is primarily focused on culinary uses, resulting in the disposal of its seeds and contributing to environmental pollution. In this context, the objective of this study was to obtain, characterize, and perform a stability study of a toothpaste made from acai seeds as an organic abrasive for oral hygiene use. The depulped acai seeds were subjected to drying, grinding, and sieving to achieve the desired granulometry before being added to the other formulation components. Stability tests were conducted through cen-trifugation, density determination, acidity index, foam formation, FTIR, TG/DTG, rheological properties, and accelerated stability study. The formulation proved stable after the centrifugation test. The obtained density value was 1.36. The acidity value was 0.1720 mg/KOH, and the initial and final foam indices were 66.66%. TG/DTG analysis showed stability around 90°C. The acai tooth-paste exhibited pseudoplastic fluid behavior. The pH ranged from 6.5 to 8.08, and it showed good stability under the study conditions. Thus, the acai seed powder was found to be an acceptable organic abrasive for incorporation into toothpastes, and it demonstrated favorable characteristics for daily use in oral hygiene.

Microorganisms drive the biogeochemical cycles that link abiotic and biotic processes in the aqueous environment and are intricately associated with plastic debris. The detection of microplastics in water and sediment introduces new concerns as small particle size allows for yet unconsidered pathways for plastics in the food web and element cycles. In this review, we present current knowledge of microbe-plastic interactions and summarize the potential impact of biogeochemical processes on plastic distribution, cycling, transport, and sedimentation. We explore how microbe-plastic interactions influence the exposure of consumers to plastics and plastic degradation products. Key methods used to elucidate biofilm development, microbial biodegradation, and plastic detection in the aqueous environment are discussed. Finally, we comment on potential future questions and research directions needed to further define the role of microorganisms in the environmental fate of microplastics.

Intercropping of maize (Zea mays L.) and peanuts (Arachis hypogaea L.) (M||P) significantly enhances crop yield. In a long-term M||P field experiment with two P fertilizer levels, we examined how long-term M||P affects topsoil aggregate fractions and stability, organic carbon (SOC), available phosphorus (AP), and total phosphorus (TP) in each aggregate fraction, along with crop yields. Compared to their respective monocultures, long-term M||P substantially increased the proportion of topsoil mechanical macroaggregates (7.6–16.3%) and water-stable macroaggregates (>1 mm) (13.8–36.1%), while reducing the unstable aggregate index (ELT) and the percentage of aggregation destruction (PAD). M||P significantly boosted the concentration (12.9–39.9%) and contribution rate (4.1–47.9%) of SOC in macroaggregates compared to single crops. Moreover, the concentration of TP in macroaggregates (>1 mm) and AP in each aggregate fraction of M||P exceeded that of the respective single crops (P<0.05). Furthermore, M||P significantly increased the Ca2-P, Ca8-P, Al-P, and Fe-P concentrations of intercropped maize (IM) and the Ca8-P, O-P, and Ca10-P concentrations of intercropped peanuts (IP). The land equivalent ratio (LER) of M||P was higher than one, and M||P stubble improved the yield of subsequent winter wheat (Triticum aestivum L.) compared with sole-crop maize stubble. P application augmented the concentration of SOC, TP, and AP in macroaggregates, resulting in improved crop yields. In conclusion, our findings suggest that long-term M||P combined with P application, sustains farmland productivity in the North China Plain by increasing SOC and macroaggregate fractions, improving aggregate stability, and enhancing soil P availability.

A novel approach for the long-term medical treatment of the inner ear is the diffusion of drugs through the round window membrane from a patient-individualized, drug-eluting implant, which is inserted in the middle ear. In this study, drug-loaded (10 wt% Dexamethasone) guinea pig round window niche implants (GP-RNIs, ~1.30 mm x 0.95 mm x 0.60 mm) were manufactured with high precision via micro injection molding (µIM, Tmold = 160 °C, crosslinking time of 120 s). The medical grade silicone elastomer MED-4244 (NuSil Technology LLC, Radnor, PA, USA) was used. Molds for µIM were 3D printed from a commercially available resin PlasGRAY V2 (Asiga, Alexandria, Australia, TG = 84 °C) via a high-resolution DLP process (xy-resolution of 32 µm, z-resolution of 10 µm, 3D printing time of about 6 h). Drug release, biocompatibility, and bio-efficacy of the GP-RNIs were investigated in vitro. GP-RNIs could be successfully produced. Wear of the molds due to thermal stress was observed. However, the molds are suitable for single use in the µIM process. About 10% of the drug load (8.2 ± 0.6 µg) was released after 6 weeks (medium: isotonic saline). The implants showed high biocompatibility over a time of 28 days (lowest cell viability ~80%). Moreover, we found anti-inflammatory effects over a time of 28 days in a TNF-α-reduction test. These results are promising for the development of long-term drug-releasing implants for human inner ear therapy.

Anxiety is a multifactorial pathology associated with oxidative stress and changes in different neurotransmitters in the central nervous system (CNS). Sarcomphalus joazeiro (Rhamnaceae) has a predicted effect on the CNS, being considered an alternative for pre-clinical investigations of anxiolytic drugs. The objective of this study is to evaluate the chemical composition, analyze the antioxidant capacity and the anxiolytic effect of the ethanolic extract of S. joazeiro leaves (EEFSJ) in zebrafish. The chemical profile was analyzed by liquid chromatography coupled to mass spectrometry (UPLC-PDA-ESI-QDA). Antioxidant action by DPPH• elimination and ABTS•⁺ capture assays. The 96 h acute toxicity and open field and light and dark tests, for sedative and anxiolytic evaluation, respectively, were applied in vivo, using zebrafish. It was possible to identify 11 compounds from the flavonoid and saponin class. EEFSJ exhibited a mean inhibitory concentration (IC50) of 185.2 ± 2.2 µg/mL and 74.17 ± 1.5 µg/mL against the DPPH• and ABTS•⁺ radicals, respectively. In vivo, EEFSJ demonstrated reduced locomotor activity and an anxiolytic effect similar to diazepam via GABAergic systems, without presenting toxicity within 96 h. These results suggest the safety of using EEFSJ for the development of clinical trials for the production of new anxiolytic drugs.

This study explores the impact of temperature and molarity in the pyrolysis of Açaí seeds (Euterpe Oleraceae, Mart.) activated with KOH on the yield of bio-oil, hydrocarbon content of bio-oil, and chemical composition of aqueous phase. The experiments were carried out at 350, 400, and 450 °C and 1.0 atmosphere, with 2.0 M KOH, and at 450 °C and 1.0 atmosphere, with 0.5 M, 1.0 M and 2.0 M KOH, in laboratory scale. The composition of bio-oils and aqueous phase determined by GC-MS, while the acid value, a physico-chemical property of fundamental importance in bio-fuels, of bio-oils and aqueous phases by AOCS methods. The solid phase (biochar) characterized by X-ray diffraction (XRD). The diffractograms identified the presence of Kalicinite (KHCO3) in biochar, and those higher temperatures favor the formation peaks of Kalicinite (KHCO3). The pyrolysis of Açaí seeds activated with KOH show bio-oil yields from 3.19 to 6.79 (wt.%), aqueous phase yields between 20.34 and 25.57 (wt.%), solid phase yields (coke) between 33.40 and 43.37 (wt.%), and gas yields from 31.85 to 34.45 (wt.%). The yield of bio-oil shows a smooth exponential increase with temperature. The acidity of bio-oil varied between 12.3 and 257.6 mgKOH/g, decreasing exponentially with temperature, while that of aqueous phase between 17.9 and 118.9 mgKOH/g, showing and exponential decay behavior with temperature, demonstrating that higher temperatures favor not only the yield of bio-oil but also bio-oils with lower acidity. For the experiments with KOH activation, the GC-MS of bio-oil identified the presence of hydrocarbons (alkanes, alkenes, cycloalkanes, cycloalkenes, and aromatics) and oxygenates (carboxylic acids, phenols, ketones, and esters). The concentration of hydrocarbons varied between 10.19 to 25.71 (area.%), increasing with temperature, while that of oxygenates from 52.69 to 72.15 (area.%), decreasing with temperature. For the experiments with constant temperature, the concentrations of hydrocarbons in bio-oil increase exponentially with molarity, while those of oxygenates decrease exponentially, showing that higher molarities favor the formation of hydrocarbons in bio-oil. Finally, it can be concluded that chemical activation of Açaí seeds with KOH favors the not only the yield of bio-oil but also the content of hydrocarbons. The study of process variables is of utmost importance in order to clearly assess reaction mechanisms, economic viability and design goals that could be derived from chemically activated biomass pyrolysis processes.

In this work the close relation between vorticity and micro-rotation in micropolar flows in Rn (n = 2 or 3) is identified and used to explain the faster decay by t^(-1/2) of the angular velocity of the micro-rotation of fluid particles, as well as establishing its optimality. For this purpose important upper and lower bounds for Leray solutions in homogeneous Sobolev spaces are derived, using the monotonicity approach recently introduced by the authors for dissipative systems in general. Several related results of interest are also given along the discussion.

Using pumps operating as turbines (PATs) offers the possibility of increasing the sustainability of water and energy systems by recovering the excess of energy that would be otherwise lost in pressure reducing valves or head loss chambers. In on-grid applications, there are many research works and implementations of PATs. However, there is still limited research for the optimization of efficiency and stability of PATs operating in off-grid systems. This work contributes to the development of stable direct current (DC) off-grid electric systems based on PATs, by optimizing and analysing the energy efficiency and stability for a wide range of operation. A self-excited induction generator (SEIG) coupled to the PAT is provided to cover the conventional type of electric ma-chines typically coupled to the hydraulic pumps. In this context, a methodology is proposed, based on the hydraulic, mechanical and electric subsystems, to define the PAT-SEIG operational area, to maximize energy conversion and the system efficiency. This will guarantee stable electric output quantities when operating in a DC off-grid system. In addition, an analytical model is proposed to estimate the PAT-SEIG operation under specific conditions. With this, water managers are suitable to design and optimize an off-grid PAT-SEIG system and to define the best hydraulic machines, electronic equipment, and all different control elements to maximize energy conversion within the target of operational limits. To develop and verify this new methodology, two micro PAT-SEIG setups were implemented in the hydraulic laboratory of IST/CERIS under typical operating conditions. The proposed solution proved to be resilient under a variable load regime. The system's maximum efficiency can be adapted using different capacitor values for the excitation of the SEIG, and the operational range is limited to the electric components. Considering the nominal efficiencies of the system’s components, the maximum p.u. efficiency obtained for each PAT-SEIG system were between 0.7 and 0.8 p.u.

Forty-eight Pasteurella multocida isolates were recovered from porcine pneumonic lungs collected in Norwestern Spain (2017- 2019). These isolates were characterized for their minimal inhibition concentrations to twelve antimicrobial agents and for the appearance of eight resistance genes: tetA, tetB, blaROB1, blaTEM, ermA, ermC, mphE and msrE. Relevant resistance percentages were shown to teracyclines, sulphamethoxazole/trimethoprim and tiamulin, thus suggesting that P. multocida isolates were mostly susceptible to amoxicillin, ceftiofur, enrofloxacin, florfenicol, marbofloxacin and macrolides. 29.2% of isolates were resistant to more than two antimicrobials. The tetracycline resistance genes (tetA and tetB) were detected in 22.9% of the isolates, but none was positive to both simultaneously; blaROB1 and blaTEM genes were found in one third of isolates but both genes were detected simultaneously in only one isolate. ermC gene was observed in 41.7% of isolates, a percentage that decreased until 22.9% for msrE; finally, ermA was harboured by 16.7% and mphE was not found in any of them. Six clusters were established based on hierarchical clustering analysis on antimicrobial susceptibility for the twelve antimicrobials. Generally, it was unable to foresee the antimicrobial susceptibility pattern for each family and the association of each particular isolate inside the clusters established from the presence or absence of the resistance genes analyzed.

In this study, the mechanical and piezoresistive properties of mortars reinforced with carbon nanotubes (CNTs) and carbon micro fibers (CMFs) are determined. Silica fume as well as a polymer with polyalkylene glycol graft chains were used as dispersant agents for the CNTs and CMFs incorporation into the cement paste. The mechanical properties of the mortar composites were investigated in respect to their flexural and compressive strength. A four-probe method was used for the estimation of their piezoresistive response. The test outcomes revealed that the combination of the dispersant agents along with a low content of CNTs and CMF by weight of cement (bwoc) result in the production of a stronger mortar with enhanced mechanical performance and durability. More specifically, there was an increase in flexural and compressive strength up to 38% and 88%, respectively. Moreover, the piezoresistive response of the reinforced cementitious materials was attributed to the variation of electrical resistivity due to tunneling transport of electrons stemming from two different mechanisms due to the incorporation of the conductive admixtures (CNTs and CMF). This work aims to contribute to the progress acceleration in the field of developing structural materials with self-sensing and electrical actuation related properties.

Açaí, Euterpe oleracea Mart. is a native plant from the Amazonian and is rich in several phyto-chemicals with anti-tumor activities. The aim was to analyze the effects of açaí seed oil on colo-rectal adenocarcinoma (ADC) cells. In vitro analyses were performed on CACO-2, HCT-116, and HT-29 cell lines. The strains were treated with açaí seed oil for 24, 48, and 72 h, and cell viability, death, and morphology were analyzed. Molecular docking was performed to evaluate the inter-action between the major compounds in açaí seed oil and Annexin A2. The viability assay showed the cytotoxic effect of the oil in colorectal adenocarcinoma cells. Acai seed oil induced increased apoptosis in CACO-2 and HCT-116 cells and interfered with the cell cycle. Western blotting showed increased expression of LC3-B, suggestive of autophagy, and annexin A2, an apoptosis regulatory protein. Molecular docking confirmed the interaction of major fatty acids with annexin A2, suggesting a role of açaí seed oil in modulating annexin A2 expression in these cancer cell lines. Our results suggest the antitumor potential of açaí seed oil in colorectal adeno-carcinoma cells and contribute to the development of an active drug from a known natural product.

In this paper, we demonstrate a method of measuring the flexural elastic modulus of ceramics at an intermediate (~millimeter) scale, at high temperatures. We used a picosecond laser to precisely cut micro-beams from the location of interest in a bulk ceramic. They had a cross-section of approximately 100 μm × 300 μm, and a length of ~1 cm. They were then tested in a thermal-mechanical analyzer at room temperature, 500°C, 800°C, and 1100°C using the four-point flexural testing method. We compared the elastic moduli of high-purity Al2O3 and AlN measured by our method with the reported values in the literature and found that the difference was less than 5% for both materials. This paper provides a new and accurate method of characterizing the high-temperature elastic modulus of miniature samples extracted from representative/selected areas of bulk materials.

: Microplastics and nanoplastics (MNPs) are becoming an increasingly severe global problem due to their widespread distribution and complex impact on living organisms. Apart from their environmental impact, the effects of MNPs on living organisms have also continued to attract attention. The harmful impact of MNPs has been extensively documented in marine invertebrates and larger marine vertebrates like fish. However, the research on the toxicity of these particles on mammals is still limited, and their possible effects on humans are poorly understood. Considering that MNPs are commonly found in food or food packaging, humans are primarily exposed to them through ingestion. It would be valuable to investigate the potential harmful effects of these particles on gut health. This review focuses on recent research exploring the toxicological impacts of micro- and nanoplastics on the gut, as observed in human cell lines and mammalian models. Available data from various studies indicate that the accumulation of MNPs in mammalian models and human cells may result in adverse consequences, in terms of epithelial toxicity, immune toxicity, and disruption of gut microbiota. The paper also discusses the current research limitations and prospects in this field, aiming to provide a scientific basis and reference for further studies on the toxic mechanisms of micro- and nanoplastics.

This study reports on the development of bio-based hydrophobic coatings for packaging papers through deposition of polyhydroxybutyrate (PHB) particles in combination with nanofibrillated cellulose (NFC) and plant wax. In a first approach, PHB particles in micrometer range (PHB-MP) were prepared through a phase-separation technique providing internally nanosized structures. The particles were transferred as a coating by dip-coating filter papers in the particle suspension, followed by sizing with a carnauba wax solution. This approach allowed partial to almost full surface coverage of PHB-MP over the paper surface resulting in static water contact angles of 105° to 122° and 129° to 144° after additional wax coating. In a second approach, PHB particles with submicron sizes (PHB-SP) were synthesized by an oil-in-emulsion (o/w) solvent evaporation method, and mixed in aqueous suspensions with 0 to 7 wt% NFC. After dip-coating filter papers in PHB-SP/NFC suspensions and sizing with a carnauba wax solution, static water contact angles of 112° to 152° were obtained. The intrinsic properties of the particles were analyzed by scanning electron microscopy, thermal analysis and infrared spectroscopy, indicating higher crystallinity for PHB-SP than PHB-MP. The chemical interactions between the more amorphous PHB-MP particles and paper fibers were identified as an esterification reaction, while the morphology of the NFC fibrillar network was playing a key role as binding agent in the retention of more crystalline PHB-SP at the paper surface, hence contributing to higher hydrophobicity.

Micro-combs [1-4] - optical frequency combs generated by integrated micro-cavity resonators – offer the full potential of their bulk counterparts [5,6], but in an integrated footprint. The discovery of temporal soliton states (DKS – dissipative Kerr solitons) [4,7-11] as a means of mode-locking micro-combs has enabled breakthroughs in many fields including spectroscopy [12,13], microwave photonics [14], frequency synthesis [15], optical ranging [16,17], quantum sources [18,19], metrology [20,21] and more. One of their most promising applications has been optical fibre communications where they have enabled massively parallel ultrahigh capacity multiplexed data transmission [22,23]. Here, by using a new and powerful class of micro-comb called “soliton crystals” [11], we achieve unprecedented data transmission over standard optical fibre using a single integrated chip source. We demonstrate a line rate of 44.2 Terabits per second (Tb/s) using the telecommunications C-band at 1550nm with a spectral efficiency – a critically important performance metric - of 10.4 bits/s/Hz. Soliton crystals exhibit robust and stable generation and operation as well as a high intrinsic efficiency that, together with a low soliton micro-comb spacing of 48.9 GHz enable the use of a very high coherent data modulation format of 64 QAM (quadrature amplitude modulated). We demonstrate error free transmission over 75 km of standard optical fibre in the laboratory as well as in a field trial over an installed metropolitan optical fibre network. These experiments were greatly aided by the ability of the soliton crystals to operate without stabilization or feedback control. This work demonstrates the capability of optical soliton crystal micro-combs to perform in demanding and practical optical communications networks.

Micro satellites must survive severe mechanical conditions during their launch phase. Therefore, structural design requirements are imposed on the micro satellites. These requirements are the strength requirement and the stiffness requirement. Usually, the structural design of a micro satellite is performed using the internal stress analysis and the natural frequency analysis, which are based on a Finite Element Method (FEM). The validity of this structural design is evaluated through vibration tests. In an early stage of development, which has a FEM model of a satellite in the process of creation, presumption of the natural frequency of a satellite may be difficult. In this study, a simple method for determining the longitudinal and lateral minimum natural frequencies of the micro satellites during the ascent phase was clarified. The structure of the micro satellites used in this research is made of aluminum alloy, and they have a monocoque structure. The Young's modulus and moment of inertia of area used to calculate the minimum natural frequencies were determined using the area ratio of the monocoque structure to the entire satellite. When this method is used, the estimated minimum natural frequencies of the longitudinal direction and the lateral direction are in agreement with the measured values acquired by the vibration tests. In order to shorten the process of micro satellites development, this paper describes a practical estimation method of the minimum natural frequency for micro satellites.

Energy transition is one of the greatest challenges facing humanity today. All micro, small, medium and large enterprises in operation will have to face it, and some can al-ready boast the first successes in this regard. This paper focuses on the involvement of these smallest players in energy transition. Micro and small entities are the largest part of the economy, having a great influence on its development. Looking at the wide scale of their activities, these entities are distinguished by a specific owner-manager relationship. This means that the final decision-making is influenced by business goals, but also by the manager's approach, their awareness of changes, and personal and other factors. Based on a structured and standardized survey questionnaire, the research was carried out using the Computer-Assisted Telephone Interviewing technique between April and May 2022 among owners of micro and small enterprises operating in Poland. The survey showed that active engagement of micro and small enterprises in energy efficiency initiatives is related to their market success and financial health.

The nuclear magnetic resonance (NMR) metabolomic analysis was applied to investigate the differences within nineteen Sicilian Nocellara del Belice mono varietal Extra Virgin Olive Oils (EVOO), grown in two zones different for altitude and soil composition. Several classes of endogenous olive oil metabolites were quantified through a nuclear magnetic resonance (NMR) three-experiment protocol coupled with a yet developed data-processing called MARA-NMR. This method, taking around one-hour experimental time per sample, faces the possible quantification of different class of compounds at different concentration’s range which would require at least three alternative traditional methods. NMR results were compared with the data of traditional analytical methods to quantify free fatty acidity (FFA), fatty acid methyl esters (FAMEs), and total phenol content. The presented NMR methodology is compared with traditional analytical practices and its consistency is also tested through slightly different data treatment. Despite the rich literature about the NMR of EVOOs, the paper points out that there are still several advances potentially improving this general analysis and overcoming the other cumbersome and multi-devices analytical strategies. Monovarietal EVOO’s composition is mainly affected by pedoclimatic conditions in turn relaying upon the nutritional properties, quality, and authenticity. Data collection, analysis and statistical processing are discussed touching the important issues related to the climate changes in Sicily and to the specific influence of pedoclimatic conditions.

In the context of restorative dentistry and the use of different techniques and dental adhesive systems, this study was to designed to assess the degree of adhesive absorption and wetting for each dental micro applicator; and also quantify the amount of lost fiber flocks after three applications of dental adhesive on the inside surface of a plastic veneer tooth in order to reveal a potential contaminating factor at the adhesive interface. Initially, one drop of dental adhesive was dispensed into a glass dental mixing well. The dental adhesive was then applied onto the inside surface of the veneer restoration for 30s using a dental micro applicator which was weighed afterwards. For each dental micro applicator, this sequence was repeated three times and measured again by the same operator. Each adhesive application was analyzed separately, to show the values independently and compare them to the initial weight. The samples of Fiber-Free Elastomer Bristle Micro Applicators (FEBM) demonstrated the best performance with a good degree of absorption and wetting of the dental adhesive without the loss fiber flocks and release-induced weight loss. The samples of Conventional Fiber Flocked Micro Applicators (CFFM) demonstrated good initial absorption and wetting of the dental adhesive, but visually shed several fiber flocks which resulted in significant weight loss and can also be considered a contaminating factor at the adhesive interface.

Interest grows in designing silicon-on-insulator slot waveguides to trap optical fields in subwavelength-scale slots and developing their optofluidic devices. However, it is worth noting that the inherent limitations of the waveguide structures may result in high optical losses and short optical paths, which challenge the device performance in optofluidics. Incorporating the planar silicon-based slot waveguide concept into a silica-based hollow-core fiber can provide a perfect solution to realize an efficient optofluidic waveguide. Here we propose a subwavelength-scale liquid-core hybrid fiber (LCHF), where the core is filled with carbon disulfide and surrounded by a silicon ring in a silica background. The waveguide properties and the Stimulated Raman Scattering (SRS) effect in the LCHF are investigated. The fraction of power inside the core of 56.3% allows an improved sensitivity in optical sensing; while the modal Raman gain of 23.60 m-1·W-1 is 2 times larger than that generated around a nano fiber with the interaction between the evanescent optical field and the surrounding Raman media benzene-methanol, which enables a significant low-threshold SRS effect. Besides, this in-fiber structure features compactness, robustness, flexibility, ease of implementation in both trace sample consumption and reasonable liquid filling duration, as well as compatibility with optical fiber systems. The detailed analyses of the properties and utilizations of the LCHF suggest a promising in-fiber optofluidic platform, which provides a novel insight into optofluidic devices, optical sensing, nonlinear optics, etc.

Micro/Nano Robot is an intelligent and efficient microrobot that can perform specific tasks under the influence of external stimuli. Depending on the application scenarios, the microrobot can adaptively transform into appropriate functional forms under different external stimuli, thus perfectly matching the needs. To date, microbots have been widely used in targeted therapy, drug delivery, tissue engineering, environmental remediation, and other fields. Although the applications of microrobots are promising, there are only a few reviews that can focus on the preparation methods and driving mechanisms. Therefore, it is necessary to outline the current status of the development of these microrobots in order to provide some new insights for the further development of the field. Therefore, this paper reviews the research progress of microrobots in terms of preparation methods, stimulus response mechanisms and applications, and highlights the applicability of different preparation methods and stimulus types. Finally, the current challenges faced by microrobots are highlighted and possible solutions are proposed to facilitate the practical application of microrobots.

When describing the tribological behaviour of technical surfaces, the need for full length scale microtopographic characterization often arises. The self-affine of surfaces and the characterization of self-affine by a fractal dimension and its implantation into tribological models are commonly used. The goal of our present work was to determine the frequency range of fractal behaviour of surfaces by analysing the microtopographic measurements of a brake plunger. We also wanted to know if the bifractal and multifractal behaviour can be detected in real machine parts. As a result, we developed a new methodology for determining the fractal range boundaries to separate the nano- and micro-roughness. In order to reach our goals, we used atomic force microscope (AFM) and stylus instrument to provide measurements in wide frequency range (19 nm - 3 mm). As a result of the power spectral density (PSD) based fractal evaluation, it was found that the examined surface could not be characterized by a single fractal dimension and that we developed a methodology for stopping the margin of validity of each fractal dimension, and we also developed a methodology for determining the limits of validity of certain fractal dimensions.

Background: Metabolic flux analysis (MFA) is an indispensable tool in metabolic engineering. The simplest variant of MFA relies on an overdetermined stoichiometric model of the cell’s metabolism under the pseudo-steady state assumption, to evaluate the intracellular flux distribution. Despite its long history, the issue of model error in the overdetermined MFA, particularly misspecifications of the stoichiometric matrix, has not received much attention. Method: We evaluated the performance of statistical tests from linear least square regressions, namely Ramsey RESET test, F-test and Lagrange multiplier test, in detecting model misspecifications in the overdetermined MFA, particularly missing reactions. We further proposed an iterative procedure using the F-test to correct such an issue. Result: Using Chinese hamster ovary and random metabolic networks, we demonstrated that: (1) a statistically significant regression does not guarantee high accuracy of the flux estimates, (2) the removal of a reaction with a low flux magnitude can cause disproportionately large biases in the flux estimates, (3) the F-test could efficiently detect missing reactions, and (4) the proposed iterative procedure could robustly resolve the omission of reactions. Conclusion: Our work demonstrated that statistical analysis and tests could be used to systematically assess, detect and resolve model misspecifications in the overdetermined MFA.

This paper deals with the formulation of a Cobot kinematic model by developing both the direct and inverse kinematics and choosing the noa transformation matrix for defining the end-effector position and orientation with respect to the base frame. These algorithms have been validated via software in Matlab environment and by means of suitable experimental tests, which have been carried out by using a UR5e Cobot. Moreover, a specific industrial application regarding the robotized assembling of a multi-cylinder IC engine, has been designed in terms of layout and corresponding automatic cycle that is intended as a sequence of the robot elementary actions. In particular, the proposed robotized cell is composed by the UR5e Cobot along with its controller and a suitable electropneumatic circuit that includes a PLC with its user interface, which are both governed by means of a specific electronic board and a switch control box. The IC engine in scale of 1:5 and specific parts of the end-effector, which takes the role of vacuum gripper and torque limiting screwdriver, have been designed and manufactured by using a 3D printer.

Amidst the escalating demands for efficient Intelligent Transportation Systems (ITS) management, the significance of accurate Origin-Destination (OD) data prediction has emerged as a paramount concern, given its indispensable role in the ITS domain. This paper introduces a groundbreaking integrated model, creatively fusing the unique strengths of Graph Convolutional Network (GCN), Residual Neural Network (ResNet), and Long Short-Term Memory Network (LSTM) into a single architecture, which we name GraphResLSTM, to exploit road segment average speed data for OD prediction. Compared with conventional road segment traffic volume data, average speed data is more readily available, significantly reducing the data accessibility barrier for OD prediction. We underscore the critical role of selection of key road segments and employs a combination of Entropy Weight Method and Technique for Order Preference by Similarity to Ideal Solution (TOPSIS) to identify 41 representative road segments from the experimental road network. In the experimental phase, we simulate 86400000 seconds of traffic conditions, generating a total of 1440000 data records. Utilizing these simulated data, we design and conduct comparative experiments between models as well as data types. The results demonstrate that both the GraphResLSTM model and road segment average speed data outperform other models and data types notably in OD prediction tasks.

Synchrotron radiation computed tomography (SRCT) allows more accurate calcified plaque and coronary stenosis assessment as a result of its superior spatial resolution, however, typical micro-computed tomography (micro-CT) systems have even higher resolution. The purpose of this study was to compare performance of high-resolution micro-CT with SRCT in the assessment of calcified plaques and a previously published dataset of coronary stenosis assessment. This experimental study involved micro-CT scanning of three-dimensional printed coronary artery models with calcification in situ used in our previously published SRCT study on coronary stenosis assessment. Measurements of coronary stenosis utilizing both modalities were compared using a paired sample t-test. The degrees of stenosis measured on all but one micro-CT dataset were statistically significantly lower than the corresponding SRCT measurements reported in our previous paper (p&lt;0.0005-0.05). This indicates that the superior spatial resolution of micro-CT was able to further reduce over-estimation of stenosis caused by extensive calcification of coronary arteries and hence false positive results. This study shows that high-resolution micro-CT outperforms SRCT in both calcified plaque and coronary stenosis assessment. This finding will become clinically important for cardiovascular event prediction and enable reclassification of individuals with low and intermediate risk into appropriate risk categories when the technical challenges of micro-CT in clinical practice such as the small field of view and demanding on image processing power are addressed.

The studied solar pot is a recent invention, which gained a utility model protection in 2021 from the Hungarian Intellectual Property Office under patent number 5489. The device is made for environmentally friendly cooking or heating (by utilizing solar energy) of foods and liquids. Its structure is similar to a double pipe heat exchanger, it has an outer mantle and an inner cooking tank. The goals of the paper are proposing a new physically-based mathematical model describing the solar pot and carrying out computer experiments with it, assembling an experimental system of the pot connected with a solar collector and performing measurements on it. Based on the results, the solar pot can successfully be used for cooking or sterilizing foods or liquids during the studied time period, in Hungary.

This paper aims to demonstrate how the detection of communities for epidemiological networks can be used to reduce the dimensionality of optimal control problems. A range of planted partition stochastic blockmodels are generated, where the underlying communities in the model vary in detectability. A high-performance computing workflow is then used to simulate and estimate reduced model dynamics for the networks, which in turn is used to find optimal control solutions.

Bimetallic Ni/Cu core-shell and Cu-Ni heterostructural micro- and nanoparticles were prepared using two simple successive reduction procedures. Monometallic Ni and Cu particles were synthesized for comparison. The phase constitutions and morphological features of the particles were studied by means of X-ray diffraction, energy-dispersive X-ray spectroscopy and scanning electron microscopy methods. All the obtained mono- and bimetallic particles were applied as electrocatalysts in the electrohydrogenation of p-nitrophenol (p-NPh). An additional electrochemical reduction of copper cations during the hydrogen saturation of Cu-containing particles was established. Some of the prepared particles exhibited high catalytic activity with an increase in the hydrogenation rate of p-NPh by more than 3 times compared to its electrochemical reduction on the non-activated cathode, and p-NPh conversion yielded the maximum values. The main product of p-NPh electrocatalytic hydrogenation over Ni-Cu particles is p-aminophenol, which is an intermediate in the synthesis of many drugs. p-Aminophenol formation is confirmed by UV-Vis spectra.

Pulmonary Embolism (PE) is the obstruction of blood arteries in the lungs by a blood clot. The mortality risk for PE is approximately 30%. Detecting pulmonary embolism in the segmental arteries of the lung is more challenging than in the main arteries and is very prone to being missed. A computer-based approach was created in this work to automatically identify pulmonary embolism in the segmental arteries using computed tomography images. The system's infrastructure includes an enhanced Mask R-CNN deep neural network that has been trained with images containing PE. The network accurately identifies the location of the pulmonary embolism on the computed tomography picture and successfully extracts its borders. The investigation was conducted by generating a local dataset. The study's performance was evaluated using pulmonary embolisms identified manually by the expert radiologist. The sensitivity, specificity, accuracy, dice coefficient, and Jaccard index values for 2130 pictures were 96.4%, 93.5%, 96.1%, 0.96, and 0.90, respectively. The improved Mask R-CNN model has demonstrated superior performance when compared to the traditional Mask R-CNN and U-Net models. This high-performance technology is designed to identify pulmonary embolism and will aid professionals in assessing the size of the embolism.

Estimating the ocean’s subsurface thermohaline information from satellite measurements is essential for understanding ocean dynamics and El Niño phenomenon. This paper proposes an improved double-output Residual Neural Network (DO-ResNet) model to concurrently estimate the ocean subsurface temperature (OST) and ocean subsurface salinity (OSS) in the tropical Western Pacific using multi-source remote sensing data, including sea surface temperature (SST), sea surface salinity (SSS), sea surface height anomaly(SSHA), sea surface wind (SSW), and geographical information (including longitude (LON) and latitude (LAT)). In the model experiment, Argo data were used to train and validate the model, and the root mean square error (RMSE), normalized root mean square error (NRMSE) and coefficient of determination (R²) were employed to evaluate the model's performance. The results showed that the sea surface parameters selected in this study have a positive effect on the estimation process, and the average RMSE and R² values for estimating OST (OSS) by the proposed model are 0.34 °C (0.05 psu) and 0.91 (0.95), respectively. Under the data conditions considered in this study, DO-ResNet demonstrates superior performance relative to the extreme gradient boosting model, random forest model, and artificial neural network model. Additionally, this study evaluates the model’s accuracy by comparing its estimations of OST and OSS across different depths with Argo-derived data, demonstrating the model's ability to effectively capture the most spatial features, and by comparing NRMSE across different depths and seasons, the model displays strong seasonal adaptability. In conclusion, this research introduces a novel artificial intelligence technique for estimating OST and OSS in the tropical Western Pacific Ocean.

This article systematically studied the A-optimal designs of a high-order mixture central polynomial model, which is an advancement of the research results for the A-optimal design of the most recent third-order mixture central polynomial model and a more accurate response surface model. This article is based on the simplex center design, obtaining measurement values at various design points, and verifying them through the A-optimal equivalence theorem. We also compare the A-efficiency of designs through examples, which can be applied to the A-optimal precise design of the fourth-order mixture model.

Refractoriness to antiseizure medications is still a major concern in the pharmacotherapy of epilepsy. For this reason, we decided to evaluate the combination of levetiracetam and cannabidiol, administered at a subthreshold dose, to limit the possible adverse effects of this phytocannabinoid. We administered levetiracetam (300 mg/kg/day, via osmotic minipumps), cannabidiol (120 mg/kg/day, injected once a day subcutaneously), or their combination for one week in epileptic rats. Saline-treated epileptic rats were the control group. Animals were monitored with video electroencephalography the week before and after the treatment. No changes were found in the controls. Levetiracetam did not significantly reduce the total seizure number or the overall seizure duration. Still, the overall number of seizures (p&lt;0.001, Duncan’s new multiple range test) and their total duration (p&lt;0.01) increased in the week following treatment withdrawal. Cannabidiol did not change seizures when administered as a single drug. Instead, levetiracetam combined with cannabidiol resulted in a significant reduction in the overall number and duration of seizures (p&lt;0.05), when comparing values measured during treatment with both pre- and post-treatment values. These findings depended on changes in convulsive seizures, while non-convulsive seizures were stable. These results suggest cannabidiol determined a remarkable potentiation of levetiracetam antiseizure effects at a subthreshold dose.

There is an important complementarity between experimental methods for the study of high-temperature viscoelasticity in the time and frequency domains, that has not always been fully exploited. Here we show that parallel processing of forced-oscillation data and microcreep records, involving consistent use of either Andrade or extended Burgers creep-function models, yields a robust composite modulus-dissipation dataset spanning a broader range of periods than either technique alone. In fitting this dataset, the alternative Andrade and extended Burgers models differ in their partitioning of strain between the anelastic and viscous contributions. The extended Burgers model is preferred because it involves a finite range of anelastic relaxation times, and accordingly a well-defined anelastic relaxation strength. The new strategy offers the prospect of better constraining the transition between transient and steady-state creep, or equivalently, between anelastic and viscous behaviour.

This article develops algorithms for the characterization and the visualization of micro-scale features by using a small number of sample points, and with a goal to mitigate for the measurement shortcomings which are often destructive or time consuming. We implement the algorithms to rapidly examine the microscopic features of a Microelectromechanical System (MEMS) surface. Such images are highly dense; therefore, traditional image processing techniques might be computationally expensive. The contribution of this research include first, we develop local and global algorithm based on modified Thin Plate Spline (TPS) model to reconstruct high resolution images of the micro-surface’s topography, and its derivatives by using low resolution images. Second, we obtain a bending energy algorithm from our modified TPS model, and use it to filter out image defects. Finally, we develop a computationally efficient Windowing technique, which combines TPS and Linear Sequential Estimation (LSE), to enhance the visualization of images. The Windowing technique allows rapid image reconstruction based on the reduction of inverse problem.

Public safety and intelligent surveillance systems critically depend on anomaly behavior detection for effective monitoring. In real-world pedestrian detection scenarios, prevalent challenges such as missed detections, complex background interference, and small target sizes hinder accurate anomaly identification. To address these issues, this study introduces YOLO-ABD, a lightweight method for anomaly behavior detection that integrates small target detection and channel shuffling. This method employs YOLOv8n as the baseline model, incorporating a small target detection mechanism in the Head part and utilizing GSConv convolution in the Backbone to enhance perceptual capability. Additionally, the SimAM attention mechanism is integrated to mitigate complex background interference, thereby improving target detection performance. Evaluation on the IITB-Corridor dataset demonstrated mAP50 and mAP50-95 scores of 89.3% and 60.6%, respectively. Generalization testing on the street-view-gdogo dataset further highlighted the superiority of YOLO-ABD over advanced detection algorithms, underscoring its effectiveness and generalizability. With a relatively small parameter count, YOLO-ABD presents an excellent lightweight solution for pedestrian anomaly behavior detection.

In order to shorten the detection time and improve the average precision on embedded devices, A lightweight and high accuracy model is proposed for passion fruit in complex environments (backlight, occlusion, overlap, sunny, cloudy, rainy). Firstly, replacing the backbone network of YOLOv5 with a lightweight GhostNet model reduces the number of parameters and computation while improving detection speed. Secondly, a new feature branch is added to the GhostNet network, and the feature fusion layer in the neck network is reconstructed to effectively combine the lower-level and higher-level features, which not only improves the accuracy of the model but also maintains its lightweight. Finally, the knowledge distillation methods are used to transfer the knowledge from the more capable teacher model to the less capable student model, which significantly improving the detection accuracy. The improved model is denoted as G-YOLO-NK. The average accuracy of the G-YOLO-NK network is 96.00%, which is 1.00% higher than the original YOLOv5s model. Furthermore, the improved model size is 7.14MB, reduced to half of the original model, and the real-time detection frame rate is 11.25 FPS on the Jetson Nano. Compared to the state-of-the-art model, the proposed model outperforms them in terms of average precision and detection performance. The present work provides an effective model for real-time detection of passion fruits in complex orchard scenes, which can provide valuable technical support for the development of orchard picking robots and greatly improve the intelligence level of orchards.

Session-based recommendations which aim to predict subsequent user-item interaction based on historical user behavior during anonymous sessions can be challenging tasks. Two main challenges need to be addressed and improved: (1) How to analyze these sessions to accurately and completely capture users’ preferences, and (2) how to identify and eliminate any interference caused by noisy behavior. Existing methods have not adequately addressed these issues since they either neglected the valuable insight that can be gained from analyzing consecutive groups of items or failed to take these noisy data in sessions seriously and handled them properly, which can jointly impede recommendation systems from capturing users’ real intentions. To address these two problems, we designed a multi-order semantic denoising (MSD) model for session-based recommendations. Specifically, we grouped items of different lengths as varying multi-order semantic units to mine the user’s primary intention from multiple dimensions. Meanwhile, a novel denoising network was designed to alleviate the interference of noisy behavior and provide a more precise session representation. The result of extensive experiments on three real-world datasets demonstrated that the proposed MSD model exhibited improved performance compared with existing state-of-the-art methods in session-based recommendation.

Day-ahead forecasting of electricity prices is important in deregulated electricity markets for all the stakeholders: energy wholesalers, traders, retailers, and consumers. Electricity price forecasting is an inherently difficult problem due to its special characteristic of dynamicity and non-stationarity. In this paper, we present a robust price forecasting mechanism that shows resilience towards aggregate demand response effect and provides highly accurate forecasted electricity prices to the stakeholders in a dynamic environment. We employ an ensemble prediction model in which a group of different algorithms participate in predicting the price for each hour of a day. We propose two different strategies, namely, Fixed Weight Method (FWM) and Varying Weight Method (VWM), for selecting each hour's expert algorithm from the set of participating algorithms. In addition, we utilize a carefully engineered set of features selected from a pool of features derived from information such as past electricity price data, weather data, and calendar data. The proposed ensemble model offers better results than both the Pattern Sequence-based Forecasting (PSF) method and our own previous work using Artificial Neural Networks (ANN) alone do on the datasets for New York, Australian, and Spanish electricity markets.

The SK model proposed by Sherrington and Kirkpatrick is an important mean field model for spin glasses. The dependence structure of Hamiltonians of the SK model is considered in this paper. We have investigated the covariance matrix of Hamiltonians of the SK model, and establish a relationship between the rank of the corresponding covariance matrix and the dimension of the space spanned by the Hamiltonians. Finally, we also give an upper bound for the rank of the covariance matrix, which might be the best.

We report a photonic-based radio frequency (RF) arbitrary waveform generator (AWG) using a soliton crystal micro-comb source with a free spectral range (FSR) of 48.9 GHz. The comb source provides over 80 wavelengths, or channels, that we use to successfully achieve arbitrary waveform shapes including square waveforms with a tunable duty ratio ranging from 10% to 90%, sawtooth waveforms with a tunable slope ratio of 0.2 to 1, and a symmetric concave quadratic chirp waveform with an instantaneous frequency of sub GHz. We achieve good agreement between theory and experiment, validating the effectiveness of this approach towards realizing high-performance, broad bandwidth, nearly user-defined RF waveform generation.

Currently there are fewer depth models applied to pepper picking detection, while the existing generalized neural networks have problems such as large model parameters, long training time, and low model accuracy.In order to solve the above problems, this paper proposes a Yolo-chili target detection algorithm for chili pepper detection. First, the classical target detection algorithm yolov5 is used as a benchmark model, and an adaptive spatial feature pyramid structure combining the attention mechanism and the idea of multi-scale prediction is introduced to improve the model's detection effect on occluded peppers and small target peppers. Secondly, a three-channel attention mechanism module is introduced to improve the algorithm's long-distance recognition ability and reduce the interference of redundant testers. Finally, the quantized pruning method is used to reduce the model parameters and realize the lightweight processing of the model. Applying the method to the homemade chili pepper dataset, the AP value of chili pepper reaches 93.11%; the accuracy rate is 93.51% and the recall rate is 92.55%.The experimental results show that yolo-chili is able to achieve accurate and real-time pepper detection under complex orchards.

GaN-based micro-size light-emitting diodes (µLEDs) have a number of appealing and distinctive benefits for display, visible-light communication (VLC), and other novel applications. The smaller size of LEDs affords them the benefits of enhanced current expansion, less self-heating effects, and higher current density bearing capacity. Low external quantum efficiency (EQE) resulting from non-radiative recombination and quantum confined stark effect (QCSE) is the serious barrier for applications of µLEDs. In this work, the reasons for the poor EQE of µLEDs are reviewed, as well as the optimization techniques for improving the EQE of µLEDs.

This research paper is part of the wider project concerning the very first detailed mapping of the overall Taiwanese hydro-power plants that took place from 2013 up to 2015 and it is currently in evaluation and finalization stage. The case of Shanping hydro-power plant has been carefully studied, photographed, documented and mapped in situ. It was one of the isolated hydro-power plant projects originally built to supply the remote area with the specific designation. Shanping hydro-power plant, as well as the other units from the early hydro-power generation era in Taiwan, are considered to be the technological heritage of civil and mechanical engineering that reflects later in all the further projects up to nowadays modern Taiwanese hydro-power plants. Unfortunately, most of the hydro-power houses from the older periods were severely damaged or destroyed by natural causes which were also the case of Shanping unit. The research is trying to reconstruct the original location of the powerhouse and its supporting structures based on available historical documents, previous studies, comparative methodology, and the current on-site observation.

Geothermal energy, being a clean energy source, has immense potential, and accurate wellbore modeling is crucial for optimizing the drilling process and ensuring safety. This paper presents a novel geothermal wellbore model based on the drift-flux approach, tested under three different temperature and pressure well conditions. The proposed model integrates the conservation equations of mass, momentum, and energy, incorporating the gas-liquid two-phase flow drift-flux model and heat transfer model. Key features include handling heat transfer between the for-mation and the wellbore, addressing the slip relationship between gas and liquid phases, and accounting for wellbore friction. The nonlinear equations are discretized using the finite differ-ence method, and the highly nonlinear system is solved using the Newton-Raphson method. Numerical simulation, validation, and comparison with existing models demonstrate the en-hanced accuracy of this model. In our tests, the model achieved high accuracy in calculating bottom hole pressure and temperature, with Mean Relative Errors (MRE) significantly lower than those of other models. These results offer valuable insights for optimizing drilling parameters and ensuring drilling safety. Comparisons indicate that this approach significantly outperforms others in capturing the complex dynamics of geothermal wellbores, making it a superior tool for geo-thermal energy development.

With the development of deep learning, several Graph Neural Networks (GNN)-based approaches have been utilized for text classification. However, GNNs encounter challenges in capturing contextual text information within a document sequence. To address this, a novel text classification model RB-GAT is proposed by combining RoBERTa-BiGRU embedding and a multi-head Graph ATtention Network (GAT). First, the pre-trained RoBERTa model is exploited to learn word and text embeddings in different contexts. Second, the Bidirectional Gated Recurrent Unit (BiGRU) is employed to capture long-term dependencies and bidirectional sentence information from the text context. Next, the multi-head graph attention network is applied to analyze this information, which serves as a node feature for the document. Finally, the classification results are generated through a Softmax layer. Experimental results on three benchmark datasets demonstrate that our method can achieve an accuracy of 71.48%, 98.45%, and 80.32% on Ohsumed, R8, and MR, which is superior to the existing nine text classification approaches.

In this study, Al-Al4C3 compounds were manufactured by mechanical milling followed by heat treatment. To analyze the microstructural evolution, the composites were sintered at 550°C during different sintering times of 2, 4 and 6 hours. The mechanical results suggest that dislocation density and crystallite size primary contribute to hardening before the sintering process, with a minimal contribution from particle dispersion in this condition. The compound exhibited a significant 75% increase in hardness after 2 hours of sintering, primarily attributed to the nucleation and growth of Al4C3 nanorods. The HRTEM analysis, combined with ge-ometric phase analysis (GPA) at and near the Al-Al4C3 interface of the nanorods, revealed strain field distributions primarily associated with partial screw dislocations and the presence of closely spaced dislocation dipoles. These findings are consistent with the microstructural parameters determined from X-ray diffraction pattern analysis using the convolutional multi-ple whole profile (CMWP) method. This analysis showed that the predominant dislocation character is primarily of the screw type, with the dislocation dipoles being closely correlated. Based on these results, it is suggested that samples with a lower weight percentage of rein-forcement and longer sintering times may experience reduced brittleness in Al/Al4C3 compo-sites. Strengthening contributions were calculated using the Langford–Cohen and Taylor equations.

Micro-gyroscopes based on the Coriolis principle are widely employed in inertial navigation, motion control, and vibration analysis applications. This paper presents our main contributions which include a novel dual-frame optomechanical gyroscope, a unique photonic crystal cavity design, and advanced numerical simulation and optimization methods. The proposed design utilizes an optical cavity formed between dual oscillating frames, whereby input rotation induces a measurable phase shift via optomechanical coupling. Actuation of the frames is achieved electrostatically via an interdigitated comb-drive design. Through theoretical modeling based on cavity optomechanics and finite element simulation, the operating principle and performance parameters are evaluated in detail. Results indicate an expected angular rate sensitivity of 22.8 mV/°/s and angle random walk of 7.1×10-5 °/h1/2, representing superior precision than to existing micro-electromechanical systems gyroscopes of comparable scale. Detailed analysis of the optomechanical transduction mechanism suggests this dual-frame approach could enable angular vibration detection with resolution exceeding state-of-the-art solutions.

This paper is regarding design and program an Micro-controller Arduino Uno board by using Arduino software to work as a photo-sensor(Active) single axial solar tracker system(SASTS). A solar panel, two photo-resistors (LDR) in two sides (north/south) of the photo-voltaic(PV) and a servo motor are connected to the Uno board, which is running a code that prepared by Arduino software IDE in advanced then it works as a tracking system. Here, the LDRs send the signal of presence or absence of the light to the board and based on that sent signal the Uno reflects a new signal to the servo motor to rotate and finds the light source. Lastly, the photo-sensor single axis tracker is made while Continuously, the system tries to face the panel to the sun and whilst changing the irradiance intensity it starts searching to find the angle of highest irradiance. Based on results that are extracted from the data, the tracker system significantly boosts the output efficiency of the solar panel. By using the Micro-controller Uno board, LDRs, servo motor and special designed mechanical base, the tracking system is constructed, based on acquired data the influence of the STS on the increasing the solar panel efficiency is more obvious. Significantly, the tracker system rises the efficiency of the PV .

The present overview of spin-dependent phenomena in nonmagnetic semiconductor microparticles (MPs) and nanoparticles (NPs) with interacting nuclear and electron spins is aimed at covering a gap between the basic properties of spin behavior in solid-state systems and a tremendous growth of the experimental results on biomedical applications of those particles. The first part of the review represents modern achievements of spin-dependent phenomena in the bulk semiconductors from the theory of optical spin orientation under indirect optical injection of carriers and spins in the bulk crystalline silicon (c-Si) – via numerous insightful findings in the realm of characterization and control through the spin polarization – to the design and verification of nuclear spin hyperpolarization in semiconductor MPs and NPs for magnetic resonance imaging (MRI) diagnostics. The second part of the review is focused on the electron spin-dependent phenomena in Si-based nanostructures, including the photosensitized generation of singlet oxygen in porous Si and design of Si NPs with unpaired electron spins as prospective contrast agents in MRI. The experimental results are analyzed by considering both the quantum mechanical approach and several phenomenological models for the spin behavior in semiconductor/molecular systems. Advancements and perspectives of the biomedical applications of spin-dependent properties of Si NPs for diagnostics and therapy of cancer are discussed.