Effective and rapid mixing is essential for various chemical and biological assays. The present work reports a simple and low-cost micromixer based on magnetofluidic actuation. The device takes advantage of magnetoconvective secondary flow, a bulk flow induced by an external magnetic field, for mixing. A paramagnetic stream of diluted ferrofluid and a non-magnetic stream are introduced to a straight microchannel. A permanent magnet placed next to the microchannel induced a non-uniform magnetic field. The magnetic field gradient and the mismatch in magnetic susceptibility between the two streams create a body force, which leads to rapid and efficient mixing. The micromixer reported here could achieve a high throughput and a high mixing efficiency of 90 % in a relatively short microchannel.

Nanoporous membranes promise energy-efficient water desalination. Hexagonal boron nitride (h-BN), like graphene, exhibits outstanding physical and chemical properties, making it a promising candidate for water treatment. We employed Car–Parrinello molecular dynamics simulations to establish accurate modeling of Na+ and Cl- permeation through hydrogen passivated nanopores in graphene and h-BN membranes. In these complex systems the classical potentials cannot properly account for the physics at play. We demonstrate that ion separation works well for the h-BN by imposing a barrier of 0.13 eV and 0.24 eV for Na+ and Cl- permeation respectively, compared to the graphene where the Cl- ion faces a negative barrier of 0.68 eV and is prone toward blockade and Na+ permeation is associated with a slightly negative barrier of 0.03 eV. From the change in the solvation shell, we get the following trend: Na/h-BN > Na/G > Cl/G > Cl/h-BN. We argue that the trend in the permeation barrier changes to Cl-h-BN > Na-h-BN > Na-G > Cl-G due to a combination of several interactions, including the distortion of the water network induced by the ions, the ion-water interaction, and the ion-nanopore interaction. Overall, the desalination performance of h-BN surpasses that of their graphene counterparts.

Surface acoustic wave (SAW) is effective for the manipulation of fluids and particles in microscale. The current approach of integrating interdigitated transducers (IDTs) for SAW generation into microfluidic channels involves complex and laborious microfabrication steps. These steps often require the full access to clean room facilities and hours to align the transducers to the precise location. This work presents an affordable and innovative method for fabricating SAW-based microfluidic devices without the need of clean room facilities and alignment. The IDTs and microfluidic channels are fabricated in the same process and thus precisely self-aligned in accordance with the device design. With the use of the developed fabrication approach, a few types of different SAW-based microfluidic devices have been fabricated and demonstrated for particle separation and active droplet generation.

Airborne micro- and nanoplastics are widely spread and pose a risk to human health. The effects of virgin (v) and home oxidised (ox) nano- and micropolystyrene (nPS/mPS) (0.1 and 1 µm) were studied on the human alveolar cells (A549). Ox-nPS/mPS, simulating photoaging, allowed effects due to environmental wear to be assessed. Cellular uptake was quantified using FITC-functionalised nPS/mPS, while cytotoxicity, changes in the acidic compartment, ROS production, mitochondrial function and DNA damage were assessed to study the effects of internalised v- and ox-nPS/mPS. The uptake was dose-dependent and very fast, since, at the lowest dose, 20.8% and 21.8% of nPS and mPS, respectively, were internalised after 1 h. Compared to v-, significant ROS increases, DNA damage and mitochondrial impairment were observed after exposure to ox-nPS/mPS. The enhancement of effects due to environmental aging processes highlighted the true potential impact on human health of these airborne pollutants.

Dynamic virtual testing by Hardware in the Loop (HIL) real time simulation systems is common to minimize physical tests to validate and verify control algorithms, logics and software, under normal and emergency conditions. The accurate but costly HIL models setup activities could have an extended use to simulate faulty conditions that are seldom observable in the real system, yet they must be detected in advance and recognized. Data driven diagnostic methods have reached a mature development, in various sectors, proving effective in early detecting slowly varying deviations from nominal patterns of signals, even without a priori knowledge of their nature and behavior. These methods rely on vast amount of data logged from real systems that are ever and ever richer of monitoring telemetries that are worth being exploited. However, due to the usually reliable and safe systems being managed, it is often difficult to collect enough data on anomalous situations to validate fault detection and isolation and limit false positives. HIL model-based simulations allow generating and observing operational domains or transients rarely observed in real operations. This allows identifying the signals that are most correlated to faults and that could be selected to setup data-based diagnostic models of parts or subsystems, which are more suitable than the whole HIL model for online diagnostics, as well as to identify the features and trends that are most symptomatic of anomalous conditions.

In this paper, a new axial-type magnetic gear with auxiliary flux-enhancing structure (AFS-AMG) is proposed. Compared to conventional AFS-AMG, it has the higher torque density and higher permanent magnet (PM) utilization factor. Firstly, the design rules and operating principles of proposed AFS-AMG are elaborated. Then, the mapping relation between the radial-type magnetic gears (RMGs) and AMGs are elucidated. Compared to its counterpart in RMGs, AFS-AMGs achieve small size. Then, the geometrical parameters of AFS-AMGs are optimized to obtain the better electromagnetic performances, where the torque density per volume and per PM volume is adopted as the evaluation standard. Finally, three different AMG topologies are constructed in finite element analysis (FEA) software for comparison. It is proven that the AFS-AMG has the largest torque density per volume and per PM volume.

Abstract Introduction: In the last thirty years, brain neuromodulation techniques have been used as an alternative to pharmacological treatment of neurological disorders. Parkinson's disease (PD) is a neurodegenerative disorder leading to bradykinesia, rest tremor, postural changes, and non-motor symptoms such as depression, anxiety, sleep disorders, pain, and cognitive decline that compromises executive functions (EFs), responsible for the orderly execution of behaviors and tasks of daily life and intentional and directed actions. To this date, a few studies with transcranial direct current stimulation (tDCS) have shown beneficial effects in PD patients concerning specific motor and non-motor symptoms, targeting the motor cortex and/or prefrontal regions. Objective: The main objective of this study was to evaluate the effects of left prefrontal tDCS across a broad spectrum of motor and non-motor symptoms of PD using established validated scales. Method: Single-blind randomized clinical trial with 18 volunteers with PD, aged between 45 and 80 years (66.1 ± 9.65), who met inclusion and exclusion criteria. Participants were submitted to assessments of motor and non-motor functions employing psychometric scales and tests to evaluate EFs and were randomly divided into two groups: control (sham stimulation) and experimental (active stimulation). All participants were involved in three separate tDCS sessions. The anode was positioned over the left dorsolateral prefrontal cortex and the cathode over the right supraorbital region, with a direct current intensity of 2mA, lasting 20 minutes. At the end of the three sessions, all participants were reassessed. Results: Significant effects of tDCS on non-motor functions were observed for cognition (verbal fluency of actions, clock copy test, appointment by visual confrontation, and verbal memory with immediate free recall) and subjective assessment of sleep quality (overall restlessness and discomfort in the arms and legs at night, leg and arm cramps at night and distressing dreams). There was also an improvement in the rate of errors and successes for congruent and incongruent stimuli of the Stroop Test. The beneficial effects on motor function were decreased rigidity, improved gait, and greater agility in the finger-tapping test. Conclusion: Three tDCS sessions showed positive results for participants with PD, producing significant improvements in various motor and non-motor functions, including sleep quality, cognition, and EFs. Additionally, the present results indicate that tDCS neuromodulation of the left dorsolateral prefrontal cortex region is feasible, safe, and provides significant objective benefits for PD patients.

Using pumps operating as turbines (PATs) offers the possibility of increasing the sustainability of water and energy systems by recovering the excess of energy that would be otherwise lost in pressure reducing valves or head loss chambers. In on-grid applications, there are many research works and implementations of PATs. However, there is still limited research for the optimization of efficiency and stability of PATs operating in off-grid systems. This work contributes to the development of stable direct current (DC) off-grid electric systems based on PATs, by optimizing and analysing the energy efficiency and stability for a wide range of operation. A self-excited induction generator (SEIG) coupled to the PAT is provided to cover the conventional type of electric ma-chines typically coupled to the hydraulic pumps. In this context, a methodology is proposed, based on the hydraulic, mechanical and electric subsystems, to define the PAT-SEIG operational area, to maximize energy conversion and the system efficiency. This will guarantee stable electric output quantities when operating in a DC off-grid system. In addition, an analytical model is proposed to estimate the PAT-SEIG operation under specific conditions. With this, water managers are suitable to design and optimize an off-grid PAT-SEIG system and to define the best hydraulic machines, electronic equipment, and all different control elements to maximize energy conversion within the target of operational limits. To develop and verify this new methodology, two micro PAT-SEIG setups were implemented in the hydraulic laboratory of IST/CERIS under typical operating conditions. The proposed solution proved to be resilient under a variable load regime. The system's maximum efficiency can be adapted using different capacitor values for the excitation of the SEIG, and the operational range is limited to the electric components. Considering the nominal efficiencies of the system’s components, the maximum p.u. efficiency obtained for each PAT-SEIG system were between 0.7 and 0.8 p.u.

The tissue micro environment or milieu consists of a highly dynamic population of cellular and non-cellular components which constitute a complex regulatory network aimed at maintaining the organ homeostasis. In the modern medicine the discovery of miRNAs is undoubtedly a promising field of research and they are essential in orchestrating immune system logic and their release in the gut micro milieu can directly affect bacterial gene expression. Here, we briefly review the role of microRNAs, focuses on their role on immune system components in physiological and pathophysiological gut micro milieu.

The Doppler band compensated by the keystone transform (KT) is limited. Therefore, it needs to be used in conjunction with the Doppler ambiguity compensation function to correct the range migration (RM) caused by maneuvering targets with Doppler ambiguity. However, the KT implemented by sinc interpolation suffers from significant performance loss at boundaries of compensation Doppler bands. Additionally, in a multi-target scenario, KT implementation methods occupy high complexity when the Doppler range of targets spans over two compensation Doppler bands. To address aforementioned issues, this study presents a variable Doppler starting point keystone transform (VDSPKT) method, where a new form of ambiguity compensation function is constructed, turning the Doppler starting point of the compensation band in KT variable. Firstly, the position of the compensation Doppler band is changed from fixed to adjustable as needed, enhancing the flexibility of KT. Crucially, the connection points of the compensation Doppler bands in sinc interpolation are reset, avoiding the performance loss at their boundaries. Also, the compensation band is adjusted to cover the narrow Doppler frequency range caused by targets, significantly improving the computational efficiency. Finally, the simulation results demonstrate that the proposed approach effectively addresses the performance degradation and high computational complexity of KT in the aforementioned scenarios, resulting in a computational load reduced by approximately 50% compared to traditional methods.

Recent years have witnessed significant advances in reinforcement learning (RL), which has registered remarkable success in solving various sequential decision-making problems in machine learning. Most of the successful RL applications, e.g., the games of Go and Poker, robotics, and autonomous driving, involve the participation of more than one single agent, which naturally fall into the realm of multi-agent RL (MARL), a domain with a relatively long history, and has recently re-emerged due to advances in single-agent RL techniques. Although, typically, the communication protocol between agents is manually specified and not altered during training, recently, some papers have shown signs of trying to emerge a communication between agents on the one hand and, on the other hand, to understand what is exchanged between agents. So, there is a growing body of literature on this topic which includes qualitative and quantitative studies and the ones that apply mixed methods. This study presents the scoping review of the methodological strategies undertaken in a total of 16 research articles. The results present the critical appraisal of quantitative methods in terms of validity and reliability and for qualitative methods considering four trustworthiness factors. In the end, relevant insights are further explored with implications and reflections on how they can benefit one's research in the field.

The aim of this research work is to study the influence of temperature, solar irradiation and wind dust on the production of solar energy. In addition, it aims to study the assessment of water quality, in particular groundwater used for cooling and cleaning photovoltaic panels (quality analysis). it's an important source, stable and sustainable can be used entirely for cooling and cleaning PV modules from the sales dust, in order to improve their performance. To date, all research studies carried out in this context of cooling and cleaning using water have not taken account of the nature of this water. We have taken a sample of water from a well in a rural area in the Darra Tafilalet region of Morocco. This region has an arid and semi-arid climate, with very high temperatures and dust-laden winds, particularly in summer. These meteorological characteristics influence the efficiency of cells, particularly photovoltaic (PV) panels, reducing their performance. Next, the water sample was analysed in the laboratory. The results obtained show that the groundwater in this area is very sensitive to cooling and cleaning photovoltaic panels. Moreover, these results indicate that the temperature, solar irradiation and wind-blown dust have a significant influence on energy production.

The purpose of this paper is to explore the implementation of Retrieval-Augmented Gen- 14 eration (RAG) technology with open-source Large Language Models (LLMs). For this purpose, a 15 web-based application named PaSSER that integrates RAG with three models - Mistral:7b, 16 Llama2:7b: Orca2:7b, is developed. In its development various technologies are used, including 17 Blockchain for managing and storing assessment results of built-in testing modules. PaSSER em- 18 ploys a set of evaluation metrics for LLMs’ performance - METEOR, ROUGE, BLEU, Perplexity, 19 Cosine similarity, Pearson correlation, and F1 score. The specialized knowledge base is in the smart 20 agriculture domain. As an illustration, the paper presents results and analysis of two tests. First one 21 is assessing the performance of LLMs across different hardware configurations, the other is deter- 22 mining the model that delivers most accurate and contextually relevant responses within the RAG. 23 The paper also discusses the integration of blockchain technology with LLMs to manage and store 24 assessment results within a blockchain environment. The tests revealed that Mistral:7b demon- 25 strates the best results across most of the evaluated metrics. The discussion section comments on 26 technical and hardware considerations that affect the performance of LLMs. Future development 27 will focus in leveraging new larger pre-trained open-source LLMs, exploring different finetuning 28 approaches, and further integration with Blockchain and IPFS.

System-of-systems (SoS) evolution is a complex and unpredictable process. Although various principles to facilitate collaborative SoS evolution have been proposed, there is a lack of experimental data validating their effectiveness. To address these issues, we present an Agent-Based Model (ABM) for SoS evolution in the Internet of Vehicles (IoV) , serving as a quantitative analysis tool for SoS research. By integrating multiple complex and rational behaviors of individuals, we aim to simulate real-world scenarios as accurately as possible. To simulate the SoS evolution process, our model employs multiple agents with autonomous interactions and incorporates external environmental variables. Furthermore, we propose three evaluation metrics: evolutionary time, degree of variation, and evolutionary cost, to assess the performance of SoS evolution. Our study demonstrates that enhanced information transparency significantly improves the evolutionary performance of distributed SoS. Conversely, the adoption of uniform standards only brings limited performance enhancement to distributed SoSs. Although our proposed model has limitations, it stands out from other approaches that utilize Agent-Based Modeling to analyze SoS theories. Our model focuses on realistic problem contexts and simulates realistic interaction behaviors. This study enhances the comprehension of SoS evolution processes and provides valuable insights for the formulation of effective evolutionary strategies.

Water footprint has been widely used to illustrate the consumption of water in many situations; for instance, in products, processes or regions of interest. In this work, we analyzed – using a sensitivity analysis approach – the effect of some variables in the calculation of the water footprint in the viticulture in Brazilian Serra Gaúcha (the major producing region of Brazilian Wine).The classical Penman-Monteith model for evapotransporation was considered, with uncertainties in some parameters (dead mulch covering fraction in the vineyard, maximum temperatures for some months, altitudes and latitudes of the site). The sensitivity analysis was conducted using the SAFE toolbox under Octave framework. The results indicated that the the portion of the water footprint corresponding to the evapotranspiration is more sensitive to the values of mulch covering fraction and the altitude of the site in comparison with the latitude and the maximum temperatures.

Image stitching is a crucial aspect of image processing. However, factors like perspective and environment often lead to irregular shapes in stitched images. Cropping or completion methods typically result in substantial loss of information. This paper proposes a method for rectifying irregularly images into rectangles using deformable meshes and residual networks. The method utilizes a convolutional neural network to quantify rigid structures of images. Choosing the most suitable mesh structure based on the extraction results, offering options such as triangular, rectangular, and hexagonal. Subsequently, the irregularly image, predefined mesh structure, and predicted mesh structure are input into a wide residual neural network for regression. The loss function comprises local and global, aimed at minimizing the loss of image information within the mesh and global target. This method not only significantly reduces information loss during rectification but also adapting to different images with various rigid structures. Validation on the DIR-D dataset shows this method outperforms state-of-the-art methods in image rectification.

This article develops a multi-perspective view on motivations and methods for tobamovirus purification through the ages, and presents a novel efficient, easy-to-use approach that can be well-adapted to different species of native and functionalized virions. We survey the various driving forces prompting researchers to enrich tobamoviruses: from the search for the causative agents of mosaic diseases in plants to their increasing recognition as versatile nanocarriers in biomedical and engineering applications. Best practice and also rarely applied options for the serial processing steps required for successful isolation of tobamoviruses are then reviewed. Adaptations for distinct particle species, pitfalls and 'forgotten' or underrepresented technologies are considered as well. The article is topped off with our own development of a method for virion preparation, rooted in historical protocols. It combines selective re-solubilization of polyethylene glycol (PEG) virion raw precipitates with density step gradient centrifugation in biocompatible iodixanol formulations, yielding ready-to-use particle suspensions. This newly established protocol and some considerations for perhaps worthwile further developments could serve as putative stepping stones towards preparation procedures appropriate for routine practical uses of the multivalent soft-matter nanorods.

The article delves into the crucial realm of compressing hydrogen in its gaseous state, a pivotal process for enhancing its viability in both civil and industrial sectors. The study initiates by providing a concise overview and comparison of diverse hydrogen storage methodologies, laying the groundwork with an in-depth analysis of hydrogen's thermophysical properties. It scrutinizes plausible configurations for hydrogen compression, aiming to strike a delicate balance between energy consumption, predominantly derived from the fuel itself, and the requisite number of compression stages. Notably, to render hydrogen storage competitive in terms of volume, pressures of at least 350 bar are deemed essential, albeit at an energy cost amounting to approximately 10% of the fuel's calorific value. Multi-stage compression emerges as a crucial strategy, not solely for energy efficiency, but also to curtail temperature rise, with an upper limit set at 200°C. This nuanced approach is underlined by the exploration of compression levels commonly cited in the literature, particularly 350 bar and 700 bar. Ultimately, the study advocates for a three-stage compression system as a pragmatic compromise, capable of achieving high-pressure solutions while keeping compression work below 10 MJ/kg, a threshold indicative of sustainable energy utilization.

This paper analyzes and compares models for predicting average magnet losses in interior permanent-magnet motors with fractional-slot concentrated windings due to harmonics in the armature reaction (assuming sinusoidal phase currents). Particularly, loss models adopting different formulations and solutions to the Helmholtz equation to solve for the eddy currents are compared to a simpler model relying on an assumed eddy-current distribution. Boundaries in terms of magnet dimensions and angular frequency are identified (numerically and using an identified approximate analytical expression) to aid the machine designer whether the more simple loss model is applicable or not. The assumption of a uniform flux-density variation (used in the loss models) is also investigated for the case of V-shaped and straight interior permanent magnets. Finally, predicted volumetric loss densities are exemplified for combinations of slot and pole numbers common in automotive applications.

Large datasets play a crucial role in the progression of surgical robotics, facilitating advancements in the fields of surgical task recognition and automation. Moreover, public datasets enable the comparative analysis of various algorithms and methodologies, thereby assessing their effectiveness and performance. The ROSMA (Robotics Surgical Maneuvers) dataset provides 206 trials of common surgical training tasks performed with the da Vinci Research Kit (dVRK). In this work, we extend ROSMA dataset with two annotated subsets: ROSMAT24, which contains bounding box annotations for instrument detection, and ROSMAG40, which contains high and low level gesture annotations. We propose an annotation method that provides independent labels for the right-handed tool and the left-handed tool. For instrument identification, we validate our proposal with a YOLOv4 model in two experimental scenarios. We demonstrate the generalization capabilities of the network to detect instruments in unseen scenarios. For gesture segmentation, we propose two label categories: high-level annotations that describe gestures at a maneuvers level, and low-level annotations that describe gestures at a fine-grain level. To validate this proposal, we have designed a recurrent neural network based on a bidirectional long-short term memory layer. We present results for four cross-validation experimental setups, reaching up to a 77.35% mAP.

The global increase in population has placed significant pressure on food security, leading to the emergence of aquaculture as a vital source of aquatic foods. However, rising costs and the limited availability of fishmeal in aquafeeds have spurred the search for alternative protein sources. While plant-based ingredients have been integrated into commercial aquafeeds, they come with challenges, including low protein content, palatability issues, and the presence of antinutritional factors. In this context, fish silage, derived from fish waste and discarded fish, stands out as a promising alternative technology due to its cost-effectiveness and sustainability attributes. The production of fish silage involves the addition of organic/inorganic acids or lactic acid bacteria to homogenized fish waste. This process yields a valuable mixture rich in peptides, free amino acids, and partially hydrolyzed proteins, offering significant nutritional benefits for animal diets. Beyond its nutritional advantages, fish silage contributes to environmental sustainability by reducing the impact of waste disposal and enhancing the value of fish waste. The objective of this review is to promote sustainable practices in the aquaculture industry in response to the increasing demand for high-quality feed nutrients. To achieve this, it includes an analysis of research results related to silage technology, an appraisal of the advantages and disadvantages of using fish silage as a feed additive, and a focus on emerging trends in this field.

This paper describes a system that is used to gather data from Smart Home sensors measuring energy consumption, analyze and predict future consumption by using machine learning algorithm for prediction. It focuses on the architecture of the system as well as the need for such system to exist in practice – why the consumption should be measured at all and how that measurement can be put to good use for achieving energy efficiency.

Earth observation satellites can capture images of specific areas in Earth's orbit based on user requirements. Despite the high demand for satellite imagery, satellites remain a scarce resource. When there are many observation tasks that are large and dense, they may interfere with each other due to satellite mobility. To address this issue, a multi-satellite scheduling algorithm based on a task merging mechanism has been proposed. This paper proposes a two-stage approach to the problem: task merging phase and merging task scheduling phase. The task merging phase introduces two methods based on Mean Shift and Complete Graph to generate the merging task set. In the merging task scheduling phase, a multi-satellite scheduling algorithm based on merging tasks is employed to solve the problem. Finally, certain measurement experiments suggest the effectiveness of the algorithm.

In this paper, we present an experimental procedure to enhance the dimensional accuracy of fabrication via Stereolithography (SLA) of features at the micro-scale. Using a custom benchmark part, deviations in feature dimensions (micro-pores diameters and depths) were detected and measured by confocal microscopy. Samples characterization and experimental observations allowed the identification of inaccuracy sources, mainly due to the laser beam scanning strategy and to the incomplete removal of uncured liquid resin in post-processing (i.e., IPA washing). As a technology baseline, the measured dimensional errors on pores diameters were up to -46%. A compensation method of the nominal laser spot diameter (85m) was defined and implemented resulting in relevant improvements in dimensional accuracy of 9.8% and 11.3% on full-open pores diameter and depth, respectively. Further investigation was performed on a customized test part to adjust the calibration procedure. The measurements revealed that the estimate of the laser beam spot size is 968m. Measurements on micro-pores having different sizes revealed that a constant compensation parameter (i.e., C=85, 96, 120m) is not fully effective at the micro-scale, where average errors still remain at -24%, -18.8%, and -16% for compensations equals to 85, 96 and 120m, respectively. A further experimental campaign allowed the identification of an effective nonlinear compensation law where the compensation parameter depends on the micro-feature size C= f (D). Results show a sharp improvement in dimensional accuracy on micro-pore fabrication, with errors consistently below +8.2%. The proposed compensation method can be extended for the fabrication of any micro-features without restrictions on the specific technology implementation. Concerning the inaccuracy introduced by the laser path, experimentation with a customized part allowed the optimization of the part orientation to reduce the errors and their differences along the X and Y machine axes.

In the face of escalating climate concerns and the push for sustainable development, the global shift towards renewable and decentralized energy systems presents new challenges and opportunities. This study investigates integrating decentralized energy production, particularly photovoltaic (PV) systems, into national energy planning, aiming to optimize energy strategies that balance local production and consumption with national objectives. By analyzing the Swiss energy model, the research employs the EnergyScope and REHO models to assess the strategic implications of decentralized versus centralized energy systems. Results show that a decentralized approach can significantly reduce PV installation needs to 35 GW, about 23% of potential capacity, and decrease annual system costs by 10% to CHF 1230 per capita. This strategy emphasizes local consumption, minimizes grid reinforcement demands, and leverages economic advantages while addressing overproduction challenges through effective energy storage and grid management. Conclusions underline the strategic value of combining centralized and decentralized methods for resilient and sustainable energy planning. The study contributes to the discourse on energy policy and infrastructure planning, advocating for a hybrid model that accommodates both local conditions and broader energy objectives, urging further research into climate impacts and technology integration for a comprehensive energy future.

Microplastics (MPs) are small pieces of plastics. They are ubiquitous in the environment and can enter the freshwater environment from surface run-off and wastewater effluent (treated and untreated), industrial effluent, degraded plastic waste, and atmospheric deposition. They are not usually destroyed but convert into one phase to another. They are a source of air pollution, occurring in dust and airborne fibrous particles. Mostly MPs are non-biodegradable while some MPs are biodegradable, which can be decomposed in the presence of ultraviolet (UV) light or by the action of microorganisms. Popular methods: chemical, spectroscopic, and thermo-analytical are available for the determination of the chemical composition and size of plastic particles. This chapter discusses the uses, health hazards, sources, and transport of MPs particles.

Biohydrogen is a versatile energy carrier for the generation of electric energy from renewable sources. Hydrogenases can be used in enzymatic fuel cells to oxidize dihydrogen. The rate of electron transfer (ET) at the anodic side between the [NiFe]-hydrogenase enzyme distal iron-sulfur cluster and the electrode surface can be described by the Marcus equation. All parameters for the Marcus equation are accessible from DFT calculations. The distal cubane FeS-cluster has a three cysteine and one histidine coordination [Fe₄S₄](His)(Cys)₃ first ligation sphere. The reorganization energy (inner- and outer-sphere) is almost unchanged upon a histidine-to-cysteine substitution. Differences in rates of electron transfer between the wild-type enzyme and the all-cysteine mutant can be rationalized by a diminished electronic coupling between the donor and acceptor molecules in the [Fe₄S₄](Cys)₄ case. The fast and efficient electron transfer from the distal iron-sulfur cluster is realized by a fine-tuned protein environment which facilitates the flow of electrons. This study enables the design and control of electron transfer rates and pathways by protein engineering.

In this study, the causal-effect between carbon dioxide emissions and forestry production and trade was investigated in Ghana by employing a data spanning from 1961 to 2014 by using the VECM and ARDL model. Evidence of the long-run equilibrium relationship in the VECM shows that, a 1% increase in veneer sheet production reduces carbon dioxide emissions by 1.47% in the long-run. There was evidence of a bidirectional causality between carbon dioxide emissions and veneer sheet production, carbon dioxide emissions and wood charcoal production, and a unidirectional causality running from carbon dioxide emissions to wood fuel production and plywood production to carbon dioxide emissions. Evidence from the long-run equilibrium relationship in the ARDL model shows that; a 1% increase in plywood production will increase carbon dioxide emissions by 0.17% in the long-run, a 1% increase in sawnwood production will increase carbon dioxide emissions by 0.17% in the long-run, a 1% increase in wood charcoal production will increase carbon dioxide emissions by 0.36% in the long-run and a 1% increase in wood fuel production will increase carbon dioxide emissions by 0.37% in the long-run.

In this study, an attempt was made to investigate the Kenya case of multivariate causality of carbon dioxide emissions by employing a time series data spanning from 1961-2011 using the ARDL method of cointegration analysis. The long-run elasticities show that, a 1% increase in financial development increases carbon dioxide emissions by 0.28%, a 1% increase in GDP per capita increases carbon dioxide emissions by 1.32% and a 1% increase in urbanization decreases carbon dioxide emissions by 1.14%. There was a unidirectional causality running from financial development, food production index, GDP per capita, industrialization and urbanization to carbon dioxide emissions. The innovation accounting shows that 20% of future shocks in carbon dioxide emissions are due to fluctuations in financial development, 9% of future shocks in financial development are due to fluctuations urbanization and 22% of future shocks in food production index are due to fluctuations in carbon dioxide emissions.

Neuronal cells are believed to rely on autophagy to maintain cellular homeostasis. Nevertheless, autophagy may be a therapeutic target for neurodegenerative diseases because of the role it plays in neuronal cell death. Despite Beclin 1 association with autophagy and apoptosis, the molecular mechanisms that underlie Tau-induced vesicular pathology and Tau protein aggregates in humans remain poorly understood. Here, we set out to examine the role of three genes-ATG14L, Beclin 1 and VPS34- in autophagy nucleation failure-associated Tau disorders in fruit fly models. We found that either reduced ATG14L levels improve neuronal outcomes, or transgenic expression of ATG6/Beclin 1 greatly reduced age-dependent neurodegeneration and Tau pathology; whereas, the loss of Beclin 1 exacerbated these effects. Prior to p-Tau accumulation, the neuronal Beclin 1 network is critical for reducing p-Tau accumulation, indicating that the loss of Beclin 1 causes Tau pathology and neurodegeneration. As neurodegeneration progressed, glial cells showed an upregulation of vesicular Beclin 1 immunoreactivities. The reduced VPS34 also resulted in p-Tau accumulation, suggesting that neurons require both Beclin 1 and VPS34 to reduce p-Tau accumulation. Our results provide mechanistic insight into the molecular pathways that cause age-dependent Tau pathology and neurodegeneration due to an excess of autophagy nucleation processes and autophagy activity, and we derive novel inferences on the therapeutic possibilities of rebalanced Beclin 1 network by reducing autophagic specific nucleation component of ATG14L.

Here we report the preparation and characterization of a novel biomimetic toothpaste containing morphogenetically active amorphous polyphosphate (polyP) microparticles enriched with retinyl acetate (“a-polyP/RA-MP”). The spherical microparticles (average size, 550±120 nm), prepared by co-precipitating sodium-polyP with calcium chloride and supplemented with retinyl acetate, were incorporated into a basis toothpaste at a final concentration of 1% or 10%. The paste containing “a-polyP/RA-MP” significantly increased the growth of human mesenchymal stem cells (MSC), compared to a commercial toothpaste which acts rather inhibitory and the paste without polyP and retinyl acetate. qRT-PCR experiments revealed that the retinoid causes an induction of the expression of the MSC marker genes for osteoblast differentiation encoding collagen type I and alkaline phosphatase. On the other hand, the polyP ingredient, supplied as Zn-polyP microparticles (“Zn-a-polyP-MP”) strongly inhibited the growth of the cariogenic bacterium Streptococcus mutans. We demonstrate that the amorphous polyP-containing toothpaste, enriched with retinyl acetate, efficiently repairs both cracks/fissures and carious lesions in the tooth enamel, and reseals dentinal tubules, already after a 5 d treatment (brushing) of teeth twice daily for 5 min as examined by SEM and quantitative EDX analysis. The stability of the occlusion of dentin cracks even turned out to resist against short high power sonication treatment. Our results demonstrate that the novel toothpaste prepared here, containing amorphous polyP and retinyl acetate, is particularly suitable for prevention/repair of (cariogenic) damages of tooth enamel/dentin and for treatment of dental hypersensitivity.

Despite the need for a sustainable energy resource, bioenergy gained its spotlight in the 2000s. Sugarcane is a significant crop in terms of sugar and energy capacity, and it can be an alternative energy source to mitigate the effects of climate change. Bioenergy production from sugarcane in Brazil is one of the most efficient. This production lends a centrality to biofuels' importance in confronting the effects of climate change. The present article reviews the Brazilian history of this crop as a biofuel source. We highlight the historical changes related to scientific, technological, industrial, and environmental advances since the beginning of the 20th century. We describe how creating governmental institutes and disseminating scientific knowledge strengthened public policies that led Brazil to occupy leadership positions in producing, distributing, and using bioenergy throughout the country. The compiled data shows the improvement and the new approaches needed in ethanol sugarcane. We developed a bibliometric analysis to evaluate Brazilian science's contribution to this process compared to other countries. Brazil's history of science and investments in sugarcane biofuel development for transportation may be divided into two phases: ethanol-only and flex-fuel cars. A third phase is starting, which is the ethanol-to-hydrogen era.

Selenium is essential for the synthesis and function of various selenoenzymes, such as glutathione peroxidases, selenoprotein P, and thioredoxin reductase, which play an important role in both antioxidant defense and limiting oxidative damage. Associations between serum selenium concentration and obstetric complications as well as pregnancy outcomes has been reported in many studies. The aim of this study was to determine whether the dietary intake of selenium, its concentration in serum and the activity of glutathione peroxidase in subsequent trimesters of pregnancy affect the birth condition of newborns assessed on the basis of the Apgar score in the 1st and 5th minute of life, birth weight, body length and head and chest circumference in physiological and complicated pregnancy course. Twenty-seven pregnant women at a mean age 29.6 ± 4.8 years from the Lower Silesia region of Poland were recruited to the study, 55% of studied group had pregnancy complications. The mean reported Se intake and serum selenium content for Polish pregnant women was in the first trimester – 56.53 μg/day and 43.75 μg/l, the second trimester – 61.79 μg/day and 41.77 μg/l and the third trimester – 58.37 μg/day and 42.13 μg/l, respectively. In the subgroup of pregnant women with a physiological pregnancy course, a weak, although statistically significant, positive correlation was found in the first trimester between Se intake and the length (R=0.48, p=0.019) and birth weight of newborns (R=0.472, p=0.022), and in the second trimester with the APGAR score at 1 (R=0.680, p=0.005) and 5 minutes (R=0.55, p=0.033), as well as in the third trimester with th APGAR score at 1 minut (R=0.658, p=0.019). The GPX value had a strong positive correlation with the APGAR score at 1 min. (R=0.650, p=0.008) in the second trimester and with the birth weight of the newborns (R=0.598, p=0.039) in the third trimester. There was no correlation between newborns' birth measurements and serum selenium concentration. In the subgroup of pregnant women with pregnancy complications, a strong, statistically significant, negative correlation was found between Se intake in the second trimester and gestational age (R=-0.618, p=0.032), and in the third trimester, a positive correlation between Se concentration in serum and head circumference (R=0.587, p=0.021). The obtained results indicate that there is a relationship between the maternal selenium status during pregnancy, both in terms of the intake of this element, its serum concentration as well as the glutathione peroxidase activity, and the anthropometric parameters of the newborn, such as birth weight, length and APGAR score, especially in the group with physiological course of pregnancy, but when pregnancy complications occur, these relationships lose their importance.

Substantial research is required to ensure that micro-mobility ride sharing provides a better fulfillment of user needs. This study proposes a novel crowdsourcing model for the ride-sharing system where light vehicles such as scooters and bikes are crowdsourced. The proposed model consists of three entities: suppliers, customers, and a management party responsible for receiving, renting, booking, and demand matching with offered resources. It can allow suppliers to define the location of their private e-scooters/e-bikes and the period of time they are available for rent. Using a dataset of over 9 million e-scooter trips in Austin, Texas, we ran an agent-based simulation six times using three maximum battery ranges (i.e., 35, 45, and 60 km) and different numbers of e-scooters (e.g., 50 and 100) at each origin. Computational results show that the proposed model is promising and might be advantageous to shift the charging and maintenance efforts to a crowd of suppliers.

In this study, the on-going research into the improvement of micro-gas turbine propulsion system performance and the suitability for application as propulsion systems for small tactical UAVs (<600 kg) is investigated. The study is focused around the concept of converting existing micro turbojet engines to turbofan with the use of a continuously variable gearbox, thus maintaining a single spool configuration and relative design simplicity. This is an effort to reduce the initial engine development cost, whilst improving propulsive performance. The BMT 120 KS micro turbojet engine is selected for performance evaluation of the conversion process using gas turbine performance software, GasTurb13. The preliminary design of a matched low-pressure compressor (LPC) for the proposed engine is then performed using meanline calculation methods. According to the analysis carried out, an improvement in the converted micro gas turbine engine performance in terms of thrust and specific fuel consumption is achieved. Furthermore, with the introduction of a CVT gearbox, fan speed operation may be adjusted independently of the core, allowing increased thrust generation or better fuel consumption. Therefore, enabling a wider gamut of operating conditions and enhances the performance and scope of tactical UAV.

Visual exploration of complex data helps interpretation, especially in the case of omics data analysis in life sciences and clinical research. Generating and analysing omics data requires bioinformatic skills, while they are interpreted by domain experts, for whom parsing large and complex data structures may be challenging. However, outcomes of visual analytics are often difficult to quantify, which emphasises precision and reproducibility, especially for research on human diseases. Here, we propose a workflow combining a reproducible computational environment with a dedicated visualisation functionality for systems biology diagrams. By linking the Galaxy with the MINERVA Platform, we visualise and explore COVID-19 transcriptomic data to demonstrate the utility of our workflow. Visualised data recapitulate findings of the original publication and offer new insights about the COVID-19 pathology. Our results offer a blueprint for quick prototyping of computational workflows that facilitate communication and exploration of complex data in biomedical research.

Iterated games, in which the same economic interaction is repeatedly played between the same agents, are an important framework for understanding the effectiveness of strategic choices over time. To date very little work has applied information theory to the information sets used by agents in order to decide what action to take next in such strategic situations. This article looks at the mutual information between previous game states and an agent's next action by introducing two new classes of games: ’invertible games’ and ‘cyclical games'. By explicitly expanding out the mutual information between past states and the next action we show under what circumstances these expressions can be simplified. These information measures are then applied to the Traveler's Dilemma game and the Prisoner's Dilemma game, the Prisoner's Dilemma being invertible, to illustrate their use. In the Prisoner's Dilemma a novel connection is made between the computational principles of logic gates and both the structure of games and the agents' decision strategies. This approach is applied to the cyclical game Matching Pennies to analyse the foundations of a behavioural ambiguity between two well studied strategies: ‘Tit-for-Tat' and ’Win-Stay, Lose-Switch'.

Angiogenesis is a critical physiological response to ischemia but becomes pathological when dysregulated and driven excessively by inflammation. We recently identified a novel angiogenic role for tripartite-motif-containing protein 2 (TRIM2) whereby lentiviral shRNA-mediated TRIM2 knockdown impaired endothelial angiogenic functions in vitro. This study sought to determine whether these effects could be translated in vivo and to determine the molecular mechanisms involved. CRISPR/Cas9-generated Trim2–/– mice that underwent a periarterial collar model of inflammation-induced angiogenesis exhibited significantly less adventitial macrophage infiltration relative to wildtype (WT) littermates, concomitant with decreased mRNA expression of macrophage marker Cd68 and reduced adventitial proliferating neovessels. Mechanistically, TRIM2 knockdown in endothelial cells in vitro attenuated inflammation-driven induction of critical angiogenic mediators, including nuclear HIF-1α, and curbed the phosphorylation of downstream effector eNOS. Conversely, in a hindlimb ischemia model of hypoxia-mediated angiogenesis, there were no differences in blood flow reperfusion to the ischemic hindlimbs of Trim2–/– and WT mice despite a decrease in proliferating neovessels and arterioles. TRIM2 knockdown in vitro attenuated hypoxia-driven induction of nuclear HIF-1α but had no further downstream effects on other angiogenic proteins. Our study has implications for understanding the role of TRIM2 in the regulation of angiogenesis in both pathophysiological contexts.

We present a study of the radio variability of bright, $S_{1.4}\geq100$ mJy, high-redshift quasars at $z\geq3$ on timescales up to 30--40 years. The study involved simultaneous RATAN-600 measurements at frequencies of 2.3, 4.7, 8.2, 11.2, and 22.3 GHz in 2017--2020. In addition, data from the literature were used. We have found that the variability index $V_S$ of the quasars ranges from 0.02 to 0.96, with about half of the objects in the sample showing a variability index in the range of 0.25--0.50, which is comparable to that of the blazars at lower redshifts. The distribution of $V_S$ at 22.3 GHz is significantly different from that at 2.3--11.2 GHz, which may be attributed to the fact that a compact AGN core dominates at the source's rest frame frequencies greater than 45 GHz, leading to higher variability indices obtained at 22.3 GHz (the $V_S$ distribution peaks around 0.4) compared to the lower frequencies (the $V_S$ distribution peaks around 0.1--0.2). Several source groups with distinctive variability characteristics were found using cluster analysis of quasars. We propose 7 new candidates for gigahertz peaked-spectrum (GPS) sources and 5 new megahertz peaked-spectrum (MPS) sources based on their spectrum shape and variability features. Only 6 out of 23 sources previously reported as GPS demonstrate a low variability level typical of classical GPS sources ($V_{S} < 0.25$) at 4.7--22.3~GHz. When excluding the highly variable peaked-spectrum blazars, we expect no more than 20\% of the sources in the sample to be GPS candidates and no more than 10\% to be MPS candidates.

Deadlock is a real problem that can cause expensive, time-dependent hang-ups or failures in distributed computing systems. Some studies have been conducted with deadlock detection and resolution in generalized request computing models, most of these studies are based on the diffusing computation scheme, where forward and backward propagated probe and reply messages respectively are diffused between dependent processes. The replies carry the dependency information between processes for the initiator. Using this dependency information initiator can detect and resolve the deadlock cycle. It has been proven in the literature that a deadlock cycle length distribution is skewed with a large majority of cycles (90%) having length two. Based on this fact an improved algorithm is proposed for handling deadlock detection in distributed computing systems under the distributed request model where each process has several requests at a time. The improved algorithm depends mainly on message propagation and timeout policy. Probe and reply messages are propagated between the initiator and its successors only to detect deadlock cycles between them. Global timeout policy is used to detect potential deadlock cycles with large length distribution. The proposed algorithm can handle concurrent executions. Simulation experiments are performed to see the effectiveness of the improved algorithm. It is found that the improved algorithm compares favorably with other existing algorithms and it shows better results for several performance metrics especially in reducing deadlock latency and execution time.

The extensive collection of paper documents and books stored in the archives of universities worldwide is a hidden cultural heritage that is frequently inaccessible. To overcome this problem, the University of Genoa, Italy, seeks to collect, store, and digitize a wide variety of items, encompassing books, manuscripts, archival materials, and documents related to museum artifacts, which together form a cultural heritage of great importance and historical significance. To make such a cultural heritage accessible to both humans and machines, images and videos must be provided with alternate descriptions, metadata, and speech-to-text transcriptions while ancient texts, for which OCR techniques are often not effective, must be accompanied by word-for-word transcripts. This work presents the design of a transcription system for the “University Museum System” at the University of Genoa, Italy (SMA-UniGe), including user interface elements and users’ engagement techniques. The goal is to create an accessible digital heritage that can be enjoyed by all, facilitated by a community of digital volunteers who are eager to dedicate their time, have a great experience, socialize, and interact on the proposed transcription system. The system exploits gamification theory to transform the typically monotonous task of transcription into a captivating experience. This activity is in line with the so-called University third mission, i.e., the activity of public engagement that aims at generating knowledge outside the academic environment to the benefit of the social, cultural, and economic development.

The aim of this work was to describe the physiological limitations induced under drought conditions in young sweet orange trees, including the crop capability to recuperate its physiological status once re-watering, and after a water withholding. The trial was conducted during two consecutive months (July and August) in two-years old sweet orange trees. Three irrigation treatments were arranged: A full irrigation treatment; (FI); a low-frequency deficit-irrigation treatment (LFDI); and a sustained-deficit irrigation (SDI) treatment. The obtained results showed that for Stem values below -1.5 MPa, significant decreases in gas exchange rates, evidencing diffusive limitations to drought stress. Additionally, there was evidence of increased osmolyte synthesis, compatible as a defensive response to prevent oxidative damage. Likewise, the isohydric behaviour observed also resulted in significant decreases in gs even for moderate stress situations. In addition, it was observed that in the LFDI treatment, the stress levels reached caused a significant increase in the levels of Pro and MDA, which were not equal to those detected in FI during the recovery periods, which leads us to assume that potential values below -1.8 MPa would be causing significant oxidative damage with no capacity for subsequent recovery, and probably affecting the final yield.

Ever since Varela and Maturana proposed the concept of autopoiesis as the minimal requirement for life, there has been a focus on cellular systems that erect topological boundaries to separate themselves from their surrounding environment. Here we reconsider whether the existence of such a spatial boundary is strictly necessary for self-producing entities. This work presents a novel computational model of a minimal autopoietic system inspired by dendrites and molecular dynamics simulations in three-dimensional space. A series of simulation experiments where the metabolic pathways of a particular autocatalytic set are successively inhibited until autocatalytic entities that could be considered autopoietic are produced. These entities maintain their distinctness in an environment containing multiple identical instances of the entities without the existence of a topological boundary. This gives rise to the concept of a metabolic boundary which manifests as emergent self-selection criteria for the processes of self-production without any need for unique identifiers. However, the adoption of such a boundary comes at a cost, as these autopoietic entities are less suited to their simulated environment than their autocatalytic counterparts. Finally, this work showcases a generalized metabolism-centered approach to the study of autopoiesis that can be applied to both physical and abstract systems alike.

This paper presents a study of the 2D roughness profiles on a flat surface generated on a steel work piece, by ball nose end milling, with linear equidistant tool paths (pick-intervals). The milled surface exploration with a surface roughness tester (on pick and feed directions) produces usually 2D roughness profiles having periodical evolutions. These evolutions can be seen as time-dependent signals, describable as a sum of sinusoidal components (the wavelength of each component being regarded as a period). In order to detect a well approximated description of these components, two appropriate signal processing techniques are used in this work: first technique provides a direct mathematical (analytical) description and is based on computer aided curve (signal) fitting (more accurate), the second technique (providing an indirect and incomplete description) is based on the spectrum generated by fast Fourier transform (less accurate). This study can be seen as a way for a better understanding the interaction between the tool and the work piece or to achieve a mathematical description of the machined surface microgeometry in terms of roughness (e. g. its description being a collection of closely spaced 2D roughness profiles).

We generalize the point information gain (PIG) and derived quantities, i.e., point information gain entropy (PIE) and point information gain entropy density (PIED), for the case of the Rényi entropy and simulate the behavior of PIG for typical distributions. We also use these methods for the analysis of multidimensional datasets. We demonstrate the main properties of PIE/PIED spectra for the real data on the example of several images, and discuss further possible utilizations in other fields of data processing.

"Public legal information from all countries and international institutions is part of the common heritage of humanity. Maximizing access to this information promotes justice and the rule of law". In accordance with the aforementioned declaration on Free Access to Law by Legal information institutes of the world, a plethora of legal information is available through the Internet, while the provision of legal information has never before been easier. Given that law is accessed by a much wider group of people, the majority of whom are not legally trained or qualified, diversification techniques, should be employed in the context of legal information retrieval, as to increase user satisfaction. We address diversification of results in legal search by adopting several state of the art methods from the web search, network analysis and text summarization domains. We provide an exhaustive evaluation of the methods, using a standard data set from the Common Law domain that we subjectively annotated with relevance judgments for this purpose. Our results i) reveal that users receive broader insights across the results they get from a legal information retrieval system, ii) demonstrate that web search diversification techniques outperform other approaches (e.g., summarization-based, graph-based methods) in the context of legal diversification and iii) offer balance boundaries between reinforcing relevant documents or sampling the information space around the legal query.

Viral co-infections, where a host is infected by multiple viruses simultaneously, are common in the human population. Human viral co-infections can lead to complex interactions between viruses and the host immune system, affecting the clinical outcome and posing challenges for treatment. Understanding the types, mechanisms, impacts, and identification methods of human viral co-infections is crucial for the prevention and control of viral diseases. In this review, we first introduce the significance of studying human viral co-infections and summarize the current research progress and gaps in this field. We then classify human viral co-infections into four types based on the pathogenic properties and species of the viruses involved. Next, we discuss the molecular mechanisms of viral co-infections, focusing on virus-virus interactions, host immune responses, and clinical manifestations. We also summarize the experimental and computational methods for identifying viral co-infections, emphasizing the latest advances in high-throughput sequencing and bioinformatics approaches. Finally, we highlight the challenges and future directions in human viral co-infection research, aiming to provide new insights and strategies for the prevention, control, diagnosis, and treatment of viral diseases. This review provides a comprehensive overview of the current knowledge and future perspectives on human viral co-infections, and underscores the need for interdisciplinary collaborations to address this complex and important topic.

Bio-molecular reagents like antibodies required in experimental biology are expensive and their effectiveness, among other things, is critical to the success of the experiment. Although such resources are sometimes donated by one investigator to another through personal communication between the two, there is no previous study to our knowledge on the extent of such donations, nor a central platform that directs resource seekers to donors. In this paper, we describe, to our knowledge, a first attempt at building a web-portal titled Bio-Resource Exchange that attempts to bridge this gap between resource seekers and donors in the domain of experimental biology. Users on this portal can request for or donate antibodies, cell-lines and DNA Constructs. This resource could also serve as a crowd-sourced database of resources for experimental biology. Further, in order to index donations outside of our portal, we mined scientific articles to find instances of donations of antibodies and attempted to extract information about these donations at the finest granularity. Specifically, we extracted the name of the donor, his/her affiliation and the name of the antibody for every donation by parsing the acknowledgements sections of articles. To extract annotations at this level, we propose two approaches – a rule based algorithm and a bootstrapped relation learning algorithm. The algorithms extracted donor names, affiliations and antibody names with average accuracies of 57% and 62% respectively. We also created a dataset of 50 expert-annotated acknowledgements sections that will serve as a gold standard dataset to evaluate extraction algorithms in the future. Contact: [email protected], [email protected] Database URL: http://tonks.dbmi.pitt.edu/brx Supplementary information: Supplementary data are available at Database online.

Based on the need for real-time sag monitoring of Overhead Power Lines (OPL) for electricity transmission, this article presents the implementation of a hardware and software system for online monitoring of OPL cables and cable sag determination. The mathematical model based on differential equations and the methods of algorithmic calculation of OPL cable sag are presented. Considering that, based on the mathematical model presented, the calculation of OPL cable sag can be done in different ways depending on the sensors used, and the presented application uses a variety of sensors. Therefore, a direct calculation is made using one of the different methods. Subsequently, the verification relations are highlighted directly and, respectively, the calculation by the alternative method, which uses another group of sensors, to generate both a verification of the calculation and the functionality of the sensors, thus obtaining a defect observer of the sensors. The hardware architecture of the OPL cable online monitoring application is presented, together with the main characteristics of the sensors and communication equipment used. The configurations required to transmit data using the ModBUS and ZigBee protocols are also presented. The main software modules of the OPL cable condition monitoring application are described, which ensure the monitoring of the main parameters of the power line and the visualisation of the results both on the electricity provider's intranet using a web server and MySQL database, and on the Internet using an Internet of Things (IoT) server. This categorisation of the data visualisation mode is done in such a way as to ensure a high level of cyber security. Starting from the mathematical model of the OPL cable sag calculation, it goes through the stages of creating such a monitoring system, from the numerical simulations carried out using Matlab to the real-time implementation of this monitoring application. The main modules of the application software are: the software module for reading quantities from the sensor network through a ModBUS Input/Output (I/O) server, the software module for real-time calculation of the OPL cable sag, the software module for read/write operations based on MySQL type data, the software module for transferring data to the user's intranet through a web server, and the software module for viewing data by authorised users based on user and password through an IoT server. The development software environments used are Matlab and Laboratory Virtual Instrument Engineering Workbench (LabVIEW).

The ability to detect the presence as well as classify the activities of individuals behind visually obscuring structures is of significant benefit to police, security and emergency services in many situations. This paper presents the analysis from a series of experimental results generated using a through-the-wall (TTW) Frequency Modulated Continuous Wave (FMCW) C-Band radar system named Soprano. The objective of this analysis was to classify whether an individual was carrying an item in both hands or not using micro-Doppler information from a FMCW sensor. The radar was deployed at a standoff distance, of approximately 0.5 m, outside a residential building and used to detect multiple people walking within a room. Through the application of digital filtering, it was shown that significant suppression of the primary wall reflection is possible, significantly enhancing the target signal to clutter ratio. Singular Value Decomposition (SVD) signal processing techniques were then applied to the micro-Doppler signatures from different individuals. Features from the SVD information have been used to classify whether the person was carrying an item or walking free handed. Excellent performance of the classifier was achieved in this challenging scenario with accuracies up to 94%, suggesting that future through wall radar sensors may have the ability to reliably recognize many different types of activities in TTW scenarios using these techniques.

The general desire of the world's population is to eat as healthily as possible, an aspect that has a direct impact on the technological complex aimed at animals raising (proper breeding systems, microclimate factors with implications for the welfare of animals, etc.), as well as on the quality of the finished products that will enter the food supply. Therefore, the authors set out to study how the growth system influences the health status of rainbow trout raised in different systems. The observed experimental factors did not undergo significant changes. However, differences were generated by the applied growth system. For the amount of glucose in the blood, no statistically significant differences were identified between the groups. In contrast, comparison of the amount of glycogen led to obtaining very distinctly significant statistical fluctuations (the mean for P-si was 2.314±0.638 and for P-i 1.980±0.822). Growth hormone varied between 0.504±0.46 in the case of P-si and 0.694±0.22 ng/ml for P-i. The values obtained for cortisol showed a significant influence of stress factors on the studied trout. The general conclusion of the present study is that various technological factors influence the health status of livestock.

This research presents the creation of a Virtual Reality experience for the Balzi Rossi museum, commemorating the centenary of Prince Albert I Grimaldi's archaeological work at the site. The project, a collaboration between the University of Genoa's 3D Lab Factory, Eurodrone, and the Balzi Rossi archaeological museum, aims to preserve and convey the site's heritage through advanced VR technology. Initially employing Unreal Engine 4, the team used photogrammetry for 3D reconstruction of the "Caviglione" and "Florestano" caves, notable for their ancient rock engravings. This first VR model, despite hardware limitations, provided an interactive exploration of the site. The subsequent development phase utilized Unreal Engine 5, incorporating Nanite technology for enhanced visual fidelity. This advancement resulted in a more detailed and immersive VR experience, presenting the Balzi Rossi cliff across different historical periods, including the Würm glaciation. Key to this phase was optimizing the VR experience for performance, focusing on stable frame rates and minimizing motion sickness, and integrating a multi-lingual interface for broader accessibility. Since November 2023, the VR setup at the Balzi Rossi Museum has been an educational and interactive feature, enabling visitors to explore the site's history virtually. This research demonstrates the potential of VR in cultural heritage preservation and education, providing a foundation for future technological improvements in the field.

Ammonia can be considered a relevant compound in the future energy sector, playing a significant role as an energy carrier, storage, or carbon-free fuel. However, the production of this molecule has a high energy demand, and the use of natural gas, which is not free of controversy due to the accidental leakage into the atmosphere produced during extraction and the fact that it is a non-renewable source, contributes to increasing greenhouse gas emissions. Reducing the process’s energy demand and carbon footprint will be essential to making ammonia a clear alternative for a carbon-free economy. Given the vast experience in ammonia production and handling, this gas seems to be the logical step forward in the evolution of the energy sector. However, the current uncertainty in the global market requires cautiousness in decision-making. Several factors may impact economic growth and human welfare, thus needing a careful assessment before taking any transcendental decisions that could affect worldwide energy prices and raw material availability.

Antarctica and its surrounding environment are considered untouched and thought that it is free from microplastics (MPs) pollution. However, recent studies and science projects have reported MPs in both water and sediment in the South Polar Regions. The reports state that the MP’s pollution occurs in this region due to fishing, tourism, and research activities by the nearby countries and nature's circulation is also part of it. The Antarctic Treaty System (ATS) has received attention on MP’s pollution and initiated research on it. MPs are tiny plastic particles with a size of less than 5 mm. It has two types, 1. Primary MPs have been manufactured directly for various applications like cosmetics and scrubbing etc 2. The secondary MPs are generated by photochemical degradation of large plastics.Although several studies have been done there is a quite gap in our understanding of the concentration, characteristics, and impact of plastics on the ecosystem of the Antarctic Region. The impact of MP’s pollution in this region may be very high. The presence of MP is a serious issue that is affecting not only the aquatic environment but also humans. It is an alarming situation that causes environmental damage. The main objective of this paper is to review MP's introduction, occurrence, sources, harmful effects, and detection methods. This review highlighted the various methodologies and analyses like density separation, microscope observation of MP’s properties Fourier-transform infrared spectroscopy (FTIR), and Raman spectrometer respectively, and urged for more research in the future and gave several recommendations to maintain the pristine region near Antarctica.

Ti and its alloys are the most commonly used materials for biomedical applications. However, bacterial infection after implant placement is still one of the significant rising complications. Therefore, the application of the antimicrobial agents into implant surfaces to prevent implant-associated infection has attracted lots of attention. Scientific papers have shown that inorganic antibacterial metal element (e.g. Ag, Cu, Zn) can be introduced to implant surfaces with the addition of metal nanoparticles or metallic compounds into electrolyte via micro-arc oxidation (MAO) technology. In this review, the effects of the composition and concentration of electrolyte and process parameters (e.g. voltage, current density, oxidation time) on morphological characteristics (e.g. surface morphology, bonding strength), antibacterial ability and biocompatibility of MAO antimicrobial coating were discussed in detail. Anti-infection and osseo-integration can be simultaneously accomplished with the selection of the proper antibacterial elements and operating parameters. Besides, MAO assisted by magnetron sputtering (MS) to endow Ti-based implant materials with superior antibacterial ability and biocompatibility was also discussed. Finally, the development trend of MAO technology in the future was forecasted.

There is a growing trend among consumers to seek out natural foods and products with natural ingredients. This shift in consumer preferences had a direct impact on both food and pharmaceutical industries, leading to a focus of scientific research and commercial efforts to meet these new demands. The aim of this work is to review recent available scientific data on foods of interest, such as artichoke, gooseberry, and polygonoideae plants, as well as olive oil and red raspberries. Interestingly, the urgency of solutions to the climate change emergency has brought new attention to by-products of grapevine bunch stem and cane, which have been found to contain bioactive compounds with potential health benefits. There is a pressing need for a faster process of translating scientific knowledge from the laboratory to real-world applications, especially in the face of the increasing societal burden associated to non-communicable diseases (NCDs), environmental crises, the post-pandemic world, and ongoing violent conflicts around the world.

Deep Learning (DL) oriented document processing is widely used in different fields for extraction, recognition, and classification processes from raw corpora of data. The article examines the application of deep learning approaches, based on different neural network methods, including Gated Recurrent Unit (GRU), Long Short-Term Memory (LSTM), and Convolutional Neural Networks (CNN). The compared models were combined with two different word embedding techniques, namely: Bidirectional Encoder Representations from Transformers BERT and Gensim Word2Vec. The models are designed to evaluate the performance of architectures based on neural network techniques for the classification of CVs of Moroccan engineering students at ENSAK(National School of Applied Sciences of Kenitra, Ibn Tofail University). The used dataset included resumes collected from engineering students at ENSAK in 2023 for a project on the employability of Moroccan engineers in which new approaches were applied, especially machine learning, deep learning, and big data. Accordingly, 867 resumes were collected from five specialties of study (Electrical Engineering, Networks and Systems Telecommunications, Computer Engineering, Automotive Mechatronics Engineering, Industrial Engineering). The results revealed good performance of the proposed models based on the BERT embedding approach compared to models based on the Gensim Word2Vec embedding approach. Accordingly, the CNN-GRU/Bert model achieved slightly better accuracy with 0.9251 compared to other hybrid models.

The present study was performed to examine that transforming growth factor beta (TGF-β) in root-surrounding tissues on deciduous teeth during the physiological root resorption regulates the differentiation induction into odontoclast. We prepared root-surrounding tissues with (R) or without (N) physiological root resorption scraped off at three regions (R1-R3 or N1-N3) from the cervical area to the apical area of the tooth and measured both TGF-β and the tartrate-resistant acid phosphatase (TRAP) activities. The TGF-β activity level was increased in N1-N3, whereas the TRAP activity was increased in R2 and R3. In vitro experiments for RANKL-mediated osteoclast differentiation revealed that TGF-β in N1-N3 and R1-R3 enhanced the TRAP activity in RAW264 cells. A genetic study indicated that the mRNA level of TGF-β1 in N1 and N2 was significantly increased, and corresponded with that of osteoprotegerin (OPG). In contrast, the expression level of receptor activator of NF-κB ligand (RANKL) was increased in R2 and R3. Our findings suggest that TGF-β is closely related to the regulation of OPG induction and RANKL-mediated odontoclast differentiation depending on the timing of RANKL and OPG mRNA expression in the root-surrounding tissues of deciduous teeth during physiological root resorption.

Loneliness is becoming prevalent across Japan in spite of its a dense population and communal culture. Surveys show 40% of adults report isolation across demographics. The contradiction emerges due to deteriorating social structure with modernization, economic parity, urbanization, and fading conventional setup. The continually social withdrawals, called “hikikomori." Relief seekers have embraced AI based emotive robots, digital avatars, and immersive VR as low-stakes social surrogates despite limited capacity to cultivate human intimacy. To stabilise government attempts awareness through reforms, scheme and support services. But a concrete transformation can be brough in with work-life balance, gender equality and rewire the metrics for self-esteem. Even a perfectly personalized AI cannot replace the human affection lacking in the society. Lasting solutions demand technological aids be balanced by confronting and reinventing community purpose and bring in structural change. Overall Japan’s endemic isolation reveals the societal fraying when modernization privileges independence over interdependence. The path forward rests on restoring cultural foundations to reverse loneliness and social isolation.

This paper explores the capability of various machine learning algorithms, including Random Forests and advanced gradient boosting techniques such as XGBoost, LightGBM, and CatBoost, to predict customer churn in the telecommunications sector. For this analysis, a dataset available to the public was employed. The performance of these algorithms was assessed using recognized metrics, including Accuracy, Precision, Recall, F1-score, and the Receiver Operating Characteristic Area Under Curve (ROC AUC). These metrics were evaluated at different phases: subsequent to data preprocessing and feature selection; following the application of SMOTE and ADASYN sampling methods; and after conducting hyperparameter tuning on the data that had been adjusted by SMOTE and ADASYN. The outcomes underscore the notable efficiency of upsampling techniques such as SMOTE and ADASYN in addressing the imbalance inherent in customer churn prediction. Notably, the application of random grid search for hyperparameter optimization did not significantly alter the results, which remained comparatively unchanged. The algorithms' performance post- ADASYN application marginally surpassed that observed after SMOTE application. Remarkably, LightGBM achieved an exceptional F1-score of 89% and an ROC AUC of 95% subsequent to the ADASYN sampling technique. This underlines the effectiveness of advanced boosting algorithms and upsampling methods like SMOTE and ADASYN in navigating the complexities of imbalanced datasets and intricate feature interdependencies.

Graph databases (GDBs) are becoming increasingly popular across scientific disciplines, being highly suitable to store and connect complex heterogeneous data. In systems biology, they are used as a backend solution for biological data repositories, ontologies, networks, pathways, and knowledge graph (KG) databases. In this review, we analyse all publications using or mentioning graph databases retrieved from PubMed and PubMed Central full-text search, focusing on the top 16 available GDB technologies. Relevant publications are then categorised according to their domain and application. We detail different approaches and highlight advantages of outstanding resources, such as UniProtKB, Disease Ontology, and Reactome, which provide graph-based solutions. We discuss ongoing efforts of the systems biology community to standardise and harmonise KG creation and the maintenance of integrated resources. Outlining prospects, including the use of GDBs as a way of communication between biological data repositories, we conclude that efficient design, querying, and maintenance of GDBs will be key for knowledge generation in systems biology and other research fields with heterogeneous data.

Treatment of bladder cancer remains a critical unmet need and requires advanced approaches, particularly the development of local drug delivery systems. The physiology of the urinary bladder causes the main difficulties in the local treatment of bladder cancer: regular voiding prevents the maintenance of optimal concentration of the instilled drugs, while poor permeability of the urothelium limits the penetration of the drugs into the bladder wall. Therefore, much research effort is spent to overcome these hurdles, thereby improving the efficacy of available therapies. The explosive development of nanotechnology, polymer science and related fields has contributed to the emergence of a number of nanostructured vehicles (nano- and micro scale) applicable for intravesical drug delivery. Moreover, the engineering approach has facilitated the design of several macro-sized depot systems (centimeter scale) capable of remaining in the bladder for weeks and months. In this article, the main rationales and strategies for improved intravesical delivery are reviewed. Here, we focused on analysis of colloidal nano- and micro-sized drug carriers, and indwelling macro-scale devices which were evaluated for applicability in local therapy of bladder cancer in vivo.

Predicting ground reaction forces (GRFs) and ground reaction moments (GRMs) through a biomechanical model-based approach offers advantages for biomechanical analysis, particularly in situations where the application of a statistical model is limited by insufficient training data. However, the current prediction method is unsuitable for clinical applications due to its long computational time. The present study developed a new optical motion capture (OMC)-based method to predict GRFs, GRMs, and joint torques. The proposed approach performed the estimation process by distributing external forces, as determined by the equation of motion, between the left and right feet based on foot deformations, thereby predicting the GRFs and GRMs without relying on machine learning or optimization techniques. We investigated the prediction accuracy during walking by comparing a conventional analysis using a force plate with the OMC results. The comparison revealed excellent or strong correlations between the prediction and measurement for all GRFs, GRMs, and lower limb joint torques. The proposed method, which provides practical estimation with low computational cost, facilitates efficient biomechanical analysis and rapid feedback of analysis results, thereby increasing its applicability for kinetics estimation in clinical settings.

This paper studies the maximum reliability of multi-hop relay UAV, in which UAV provides wireless services for remote users without direct communication link on the ground as a coded cooperative relay. In this paper, the analytical expressions of total power loss and total bit error rate are derived as reliability measures. Firstly, based on the environmental statistical parameters, a LOS probability model is proposed. Then the problem of minimizing the bit error rate of static and mobile UAVs is studied. The goal is to minimize the total bit error rate by jointly optimizing the height, elevation, power and path loss, and subject to the maximum allowable path loss con-straints, transmission power allocation constraints and UAV height and elevation constraints. At the same time the total path loss is minimized to achieve maximum ground communication cov-erage. However, the formulated joint optimization problem is non-convex and generally difficult to solve. Therefore, we decomposed the problem into two subproblems and proposed an effective joint optimization iteration algorithm. Finally, the simulation results are given, and the analysis shows that the optimal height of different reliability measures is slightly different, and using the mobility of UAVs can improve the reliability of communication performance.

This study proposed to use wearable EEG to study the impact of vipassana mindfulness practice on beginner's physiological and neurological responses. Mindfulness meditation has been shown to have numerous benefits, including stress reduction, improved attention and cognitive function, and enhanced emotional regulation. The roots of mindfulness meditation in Buddhism emphasize cultivating present-moment awareness and insight. However, the neural mechanisms together with physiological mechanism and their interaction underlying these benefits remain poorly understood. Method: One middle age man (50 years old) participated in this longitudinal study using wearable EEG to investigate the neurophysiological change during a one-month consecutive vipassana mindfulness practice. Both EEG and heart rate responses were recorded each time, before (5 minutes), during (20 minutes), and after (5 minutes) meditation sessions. The EEG and HR data were analyzed by Matlab and EEGlab to examine changes in brainwave activity and heart rate. Results: alpha peak frequency (APF) is significantly lower after mindfulness meditation, as shown by comparison of APF before mindfulness (pre-5) and during mindfulness practice (med-20), and comparison between APF of pre-5 and after mindfulness practice (post-5). The same is with the beta peak power. While for theta peak frequency, it is significant lower during mindfulness meditation (med-20), when comparing to either pre-5 or post-5. See figure 1a. However, peak power index is not so sensitive, and it is more obvious in theta wave band. That is, the theta power peak is significantly lower after meditation, as can be observed in comparison between pre-5 and med-20, also between pre-5 and med-20. See figure 1b. STATE Heart-mean (bpm) Heart-std(bmp) pre-5 69.88 3.88 med-20 68.36 2.81 post-5 69.55 4.13 t-value test (pre-med) 0.0694 0.0003 t-value test (pre-post) 0.7934 0.3656 t-value test (post-med) 0.3193 0.0001 Table 1. The difference of Heart rate (mean and SD) in before (pre-5), during (med-20) and after (post-5)mindfulness meditation. We find significant change in standard deviation (SD) of heart rate between meditation and non-meditation mental states, as shown in table 1. The study provides insights into the underlying neurophysiological mechanisms of mindfulness meditation using wearable EEG devices. It demonstrates that in term of EEG measurement, spectrum frequency can be more sensitive than spectrum power; also heart rate variability as measured by SD is more sensitive to mean of HR. The proposed study contributes to the literature by using wearable EEG devices to collect data in a more accessible and convenient manner.

Microscopic vision plays an important role in automated micro-assembly. However, some uncertain factors in the assembly process, such as occlusion and stains can lead to the mistakes of feature extraction. Herein, to solve the problem, the deep learning techniques are introduced into the feature recognition tasks, focusing on the attention mechanism and visualizing CNNs for DL-based microscopic vision. The main contributions are summarized as follows: The CBAM attention mechanism is combined with the YOLOv5 algorithm to improve the accuracy and robustness of feature extraction. The micropart feature occlusion experiment results show that at 70% occlusion degree, YOLOV5-CBAM can reach 97.9% [email protected], which is 4.6% higher than the original one. Visualization analysis of DL-based model is conducted using Grad-CAM to make the decision result more transparent and avoid potential visual detection risks during assembly. The heatmap matching degree between GT area and high-light area is increased by 27.81% on average, which further verify the effectiveness of attention mechanism in micropart feature localization. Additionally, micropart surface stain and droplet quality classification models based on ResNet50 are trained to replace the manual sorting. The visual results are consistent with human eye discernment and judgement, confirming the reliability of parts and droplets sorting.

Objectives: Social distancing measures are currently implemented to control COVID-19 pandemic in many countries, including Saudi Arabia. The aim of this study was therefore to evaluate the awareness and adherence of the Saudi population to these measures. Methods: A web-based questionnaire was designed with 16 questions (8 questions related to demographics, 3 in relation to awareness about social distancing and 5 related to overall practice of social distancing). Results: 5105 participants completed the survey [58.4% female, 66.3% young individuals (aged 18-37 years), 55.8% bachelor degree holders, and 51.0% from the western region]. The Saudi Ministry of Health (MOH) was the main source of information about COVID-19 for most participants (78.2%). High awareness (81.3%) regarding social distancing was observed, associated mainly with female participants, those from the middle region and those with high education and income. Overall implementation of social distancing was satisfactory (score 3.13/5), with 37.8% never leaving home during the home-stay period. Better adherence to social distancing was observed for female participants, higher degree holders and those aged over 38 years. Conclusions: Organised plans by the Saudi MOH have been effective in raising awareness and improving practice of social distancing among public. However, the observed lower practice of social distancing by individuals with lower education and income indicates the need for targeted interventions to achieve better outcome.

Vaccines decrease morbidity and mortality. Nevertheless, their benefits depend on public response. During COVID-19, vaccine hesitancy and refusal were rampant, threatening public health. A thorough understand-ing of opponents' arguments is required to address the diffusion of unreliable information on social media and prevent vaccine hesitancy from developing into vaccine refusal. Accordingly, the article examines vac-cine opponents' justifications on social media. Textual content analysis of reader comments on three health-related Israeli Facebook pages was conducted. Data collection encompassed the Israeli COVID-19 vaccination period from October 2020 to May 2022. The comments were analyzed according to the health beliefs model (HBM). We found that vaccine opponents were characterized by low perceptions of the severity of the disease combined with high perceptions of the damages of the vaccine; low perceived benefits of vac-cine compliance; vaccine hesitancy and fear along with public distrust as barriers to change; and call for ac-tion to resist the vaccine and spread related anti-establishment views on the web. As vaccination hesitancy was found to develop into public distrust in the state systems and escalate into conspiracy beliefs and an-ti-vaccination activism, its early detection may prevent future vaccine resistance.

Bio-inspired gyroid triply periodic minimum surface (TPMS) lattice structures have been the focus of research in automotive engineering because they can absorb a lot of energy and have wider plateau ranges. The main challenge is determining the optimal energy absorption capacity and accurately capturing plastic plateau areas using finite element analysis (FEA). Using nTop's Boolean subtraction method, this study combined walled TPMS gyroid structures with normal TPMS gyroid lattice. This made a composite TPMS-gyroid lattice with relative densities ranging from 14% to 54%. Using the ideaMaker software and the fused deposition modeling (FDM) Raise3D Pro 2 3D printer to print polylactic acid (PLA) bioplastics in 1.75 mm filament made it possible to slice computer aided design (CAD) models and fabricate 36 lattices samples precisely layer by layer technique. Shimadzu 100kN testing equipment was utilized for the mechanical compression experiments. And the validation using finite element analysis (FEA). Further, CTG was examined using a field emission scanning electron microscope (FE-SEM) before and after compression testing. The composite TPMS gyroid lattice showed potential as shock absorbers for vehicles with relative densities of 33%, 38%, and 54%. The Gibson-Ashby model showed that the composite TPMS gyroid lattice deformed mainly by bending, and the size effect was seen when the relative densities were less than 15%. The lattice's relative density had a significant impact on its ability to absorb energy. The research also explored the use of these innovative foam-like composite TPMS-gyroid lattices in high-speed crash box scenarios, potentially enhancing vehicle safety and performance.

Industria 4.0 is present in smart and digital manufacturing, making manufacturing companies improve productivity, reducing delivery time and related costs. The objective of this work is to demonstrate through three integrated MPS Festo stations (Distribution, Pick \& Place and Sorting), using the Internet of Things and Google Analytics technologies, the benefits in relation to remote performance monitoring. The intended objective is achieved through the implementation of the monitoring system at the three MPS Festo stations. The data obtained through the integration of the Festo stations and their respective sensors are processed and analyzed in a cloud infrastructure, so that the main metrics are visualized and transmitted on a panel. This monitoring system improves the perception of process performance, as the main performance metrics are displayed, such as productivity, cycle time and parts produced. The cloud infrastructure allows remote viewing and monitoring of the system.

Despite the extensive literature on missing data theory and cautionary articles emphasizing the importance of realistic analysis for healthcare data, a critical gap persists in incorporating domain knowledge into missing data problem formulation, assumption specification, and method development. In this paper, we highlight the gap particularly for observational data from healthcare facilities. We address this gap by identifying ten fundamental missingness scenarios arising during data measurement, recording, and pre-processing in observational health data, influenced by physicians, patients, healthcare facilities, and data scientists. We analyze the effect of scenarios on estimand formulation, missing data identification, estimation, and sensitivity analysis. To emphasize how domain-informed analysis can improve method reliability, we conduct simulation studies under the influence of various missingness scenarios. We compare the results of three common methods in medical data analysis (complete-case analysis, Missforest imputation, and inverse probability weighting estimation) for two estimands (variable mean estimation and classification accuracy). We advocate for our analysis approach as a reference for the analysis of observational health data. Furthermore, we posit that the proposed analysis framework is applicable to other medical domains, including medical wearable data analysis.

This review provides a comprehensive and updated information on chalcones, presenting their sources, methods of identification and properties putting emphasis on applications in agricultural industry. Vast exploitation of synthetic pesticides led to the weed and pest resistance issue, causing economic loss but more importantly health risk due to pesticide overuse. Because one of the aim of the European Green Deal 2030 is the Farm to Fork strategy which targets on reducing by 50% the use of chemical pesticides by 2030, and push towards natural pesticides which are more environmentally friendly and restore natural resources, chalcones and their derivatives seem to fit perfectly. They have herbicidal, fungicidal, bactericidal and antiviral properties. Moreover, chalcones are naturally occurring substances, known for their favorable health effect for years, working on many areas. This review is complementary to the previous ones describing chalcones use in agriculture, updates them but additionally shows methods of detection.

Despite being stored at 113 K and atmospheric pressure, LNG cold potential is not exploited to reduce green ships’ energy needs. An innovative system based on three Organic Ranking Cycles integrated into the regasification equipment is proposed to produce additional power and recover cooling energy from condensers. A first-law analysis identified ethylene and ethane as suitable working fluids for the first and the second ORC making available freshwater and ice. Propane, ammonia and propylene could be arbitrarily employed in the third ORC for air-conditioning. An environmental analysis that combines exergy efficiency, ecological indices and hazard aspects for marine environment and ship’s passengers, indicated propylene as safer and more environmentally friendly. The exergy analysis confirms more than 20% of the LNG potential can be recovered from every cycle to produce a net clean power of 76 kW, whereas 270 kW can be saved by recovering condensers' cooling power to satisfy some ship needs. Assuming the sailing mode, a limitation of 162 kg in LNG consumptions was determined, avoiding the emission of 1584 kg of CO2 per day. Marine thermal pollution is reduced by 3.5 times by recovering the working fluids' condensation heat for the LNG pre-heating.

Despite of being an exceptionally biodiversity rich country, the forest coverage of Bangladesh is declining at an alarming rate. Declaration and management of protected areas in this regard is one of the efforts from government side to tackle the loss of biodiversity. The limited numbers of forest-protected areas (FPA), established to conserve the dwindling forest biodiversity of the country with high pressure on them for timber, non-timber forest products, and fuelwood - makes their management challenging. Moreover, most of the FPAs of the country declared only in the recent decades with very limited infrastructure, manpower and policy support for monitoring and governance. Some people-centred approaches for the management of FPAs and alternative livelihood and income generation subsidies although made available through a few project interventions, their number are still inadequate and performance remains less than satisfactory. This chapter provides a critical review of the FPAs of Bangladesh looking at their role in biodiversity conservation, management challenges, and key lessons from previous management interventions with recommendations for the future. It has been revealed that the FPA system of Bangladesh still poorly represents the diverse forest ecosystems with relatively small forest size and lack of corridors for the movement of wildlife. There are ample opportunities to render co-management of FPAs an effective strategy to minimize the conflicts in FPAs management in the country. It is, however, important to ensure the access of local forest-dependent people to different alternative income generating options that may adequately support their livelihoods.

Six bacterial strains with differing abilities to produce varying concentrations of Indole Acetic Acid were tested individually and in consortia for plant growth promoting and fitness related traits of Cicer arietinum. In all experiments the presence of the nitrogen fixer Mesorhizobium ciceri resulted in increased biomass production. In the absence of this strain, IAA Psedomonas putida and Bacillus megaterium hinder plant growth and fitness related traits. The application of mixes of the three strains always resulted in better plant performance when M. ciceri was present. Whereas P. putida has a noticeable plant growth-promoting effect B. megaterium resulted less effective. The low levels of IAA produced by the selected strains had a significantly greater positive effect on plant biomass accumulation, flower, pods and seed production as well as on total plant nitrogen and nitrogen concentration in seed than high IAA producer strains.

According to previous studies the median raphe region (MRR) is known to contribute significantly to social behavior. Beside serotonin, there are reports of a small population of dopaminergic neu-rons in this region. Dopamine is linked to reward and locomotion, but very little has been known about its role in the MRR. To address that, we first confirmed the presence of dopaminergic cells in the MRR of mice (immunohistochemistry, RT-PCR) and humans (RT-PCR). Next, we used chemogenetic technology in mice containing Cre enzyme under the promoter of the dopamine transporter (DAT). With the help of an adeno-associated virus, artificial receptors were expressed in the dopaminergic cells of the MRR (DAT-MRR). Four weeks later, extensive behavioral charac-terization started 30 minutes after the injection of the artificial ligand (Clozapine-N-Oxide). Stimu-lation of DAT-MRR decreased social interest without influencing aggression and with an increase in social discrimination. Additionally, inhibition of the same cells increased the friendly social be-havior during social interaction test. No behavioral changes were detected in anxiety, memory and locomotion. All in all, dopaminergic cells were present both in the mice and human MRR, and manipulation of dopaminergic neurons of the MRR elicited a specific social response.

The article presents several innovative systems developed through student laboratory projects, including two autonomous vehicles, a four-legged walking robot, an active ankle-foot orthosis, a ball on beam balancing mechanism, a ball on plate system, and a manipulator arm—all powered by pneumatic artificial muscles (PAMs). Fluidic muscles offer significant potential in various mechatronic systems, robots, and manipulators due to their flexible, lightweight nature and compliance. Their ability to produce smooth and adaptable motions is particularly beneficial in applications requiring natural and human-like movement, such as rehabilitation and assistive devices. Although PAMs powered control systems face challenges with nonlinear phenomena, their biologically inspired design holds promise for future applications across various industries. These may include innovative applicability in industrial, automotive, and aerospace sectors, as well as use in sports, medical aids, entertainment, and animatronics. Incorporating self-made laboratory systems actuated by PAMs into control systems education offers a comprehensive learning opportunity that combines theoretical concepts with hands-on experience. This approach develops the necessary skills of future engineers, expanding their understanding of technical principles and preparing them for future challenges in engineering practice.

In the recent years, tubular nanostructures have been related with immense advances in various fields of science and technology. Considerable research efforts have been centered on the theoretical prediction and manufacturing of non-carbon nanotubes (NTs), which meet modern requirements for the developing of novel devices and systems. In this context, diatomic inorganic nanotubes formed by atoms of elements from the 13th group of the periodic table (B, Al, Ga, In, Tl) and nitrogen (N), have received much research attention. In the present work, the elastic properties of single-walled boron nitride, aluminium nitride, gallium nitride, indium nitride and thallium nitride nanotubes were numerically evaluated using the nanoscale continuum modelling approach (also called molecular structural mechanics). The elastic properties (rigidities, surface Young´s and shear moduli, and Poisson´s ratio) of nitride nanotubes are discussed with respect to the bond length of the corresponding diatomic hexagonal lattice. The results obtained contribute to a better understanding of the mechanical response of nitride compound-based nanotubes, covering a broad range from the well-studied boron nitride NTs to the hypothetical thallium nitride NTs.

The supply chain has incorporated products by putting them into hair scarfs. This study introduces the use of mini chips in health and beauty products and can reduce fatigue through enhanced sleep patterns. The mini chip could be placed in the scarf and used as a prototype. RFID technology provides the supply chain with specific information that is used to identify products and make communication easier. (Muhammad, et. al. 2013) This paper presents a new tool herein referred to as a scarf prototype which is developed to analyse EMG (electromyogram), ECG (electrocardiography), EEG (electroencephalogram), and EOG (electro-oculogram) signals that focuses in the area of sleep disorders. The mini chips used can be used to determine a solution for sleep disruption by using automated analytics. This could lead to improvement in our understanding of sleep disruption and overall sleep physiology. Automated technology allows repeated measurements, evaluation of sleep patterns, and provide suggestions to improve a person’s quality of sleep. This analysis compares the use of polysomnography and the scarf prototype. The analytics provide models and shows correlation between variables, such as EMG, ECG, EEG, and EOG. This study shows that the results from the scarf prototype is just as reliable as the original method, polysomnography.

To improve carbon efficiency for urban logistics service system composed of a third-party logistics service provider (3PLs) and an e-business enterprise, low-carbon operation game between them was studied. Considering low carbon technology investment cost and sales expansion effect of low carbon level, profit functions for both players were constituted. Based on their different bargaining capabilities, totally 5 types of game scenarios were designed. Through analytical solution, Nash Equilibria under varied scenarios were obtained. By analyzing these equilibria, 4 major propositions were given, in which, some key variables and system performance index were compared. Results show that the best system yields could only be achieved under the fully cooperative situation; limited cooperation only for carbon emission reduction would not benefit the system performance improvement; E-business enterprise-leading game’s performance overtook 3PLs-leading ones.

GaN ultraviolet photodetector with metal-semiconductor-metal structure is achieved by growing on a periodic trapezoid column-shape patterned sapphire substrate using metalorganic chemical vapor deposition. Under 5-V reverse bias, the photodetector fabricated on such patterned sapphire substrate exhibits a lower dark current, a higher photocurrent, and a 476 % enhancement in the maximum responsivity as compare with those of the photodetector fabricated on conventional flat sapphire substrate. It is also found that the much larger UV-to-visible rejection ratio and the fact that responsivity drops in a smaller cut-off region are observed from photodetector fabricated by using a periodic trapezoid column-shape patterned sapphire substrate. These phenomena may all be attributed to the reduction of threading dislocation density and the improved quality of GaN film, as well as the internal reflection and/or scattering effect on the interface between GaN film and the periodic trapezoid column-shape pattern of the substrate.

Background: Post-acute sequelae of SARS-CoV-2 infection (PASC) is a complicated disease that affects millions of people all over the world. Previous studies have shown that PASC impacts 10% of SARS-CoV-2 infected patients of which 50-70% are hospitalized. It has also been shown that 10-12% of those vaccinated against COVID-19 were affected with PASC and its complications. The severity and the later development of PASC symptoms is positively associated with the early intensity of the infection. Results: The generated health complications caused by PASC involve a vast variety of organ systems. Patients affected by PASC have been diagnosed with neuropsychiatric and neurological symptoms. Cardiovascular system also has been involved and several diseases such as myocarditis, pericarditis, and coronary artery diseases were reported. Chronic hematological problems such as thrombotic endothelialitis and hypercoagulability were described as a condition that could increase the risk of clotting disorders and coagulopathy in PASC patients. Chest pain, breathlessness, and cough in PASC patients were associated with respiratory system in long COVID-19 causing respiratory distress syndrome. The observed immune complications were notable, involving several diseases. Renal system also was impacted and result in raising the risk of diseases such as thrombotic issues, fibrosis, and sepsis. Endocrine gland malfunction can lead to diabetes, thyroiditis, and male infertility. Symptoms such as diarrhea, nausea, loss of appetite and taste were also among reported observations due to several gastrointestinal disorders. Skin abnormalities might be an indication of infection and long-term implications such as persistent cutaneous complaints were linked to PASC. Conclusions: Long COVID is a multidimensional syndrome with considerable public health implications, affecting several physiological systems and demanding thorough medical therapy as well as more study to address its underlying causes and long-term effects.

This paper presents a study about the integration of Piezoelectric Energy Harvesting Systems (PE-EHS) in building envelopes for powering Fiber Bragg Grating (FBG) sensors, enabling efficient and low-consumption monitoring with the objective to leverage Structural Health Monitoring (SHM). The research includes preliminary tests conducted in a real environment to validate the PE-EHS when fully integrated into the façade, capturing mechanical vibrations generated mainly by wind loads. Based on these activities, the final configuration of PE-EHS is defined to provide a complete system for façade monitoring. This integrated system includes the Piezoelectric Generator (PEG), Supercapacitor (SC), Power Conditioner Circuit (PCC), Fibre Optic Sensing (FOS) Interrogator, and the IoT Gateway trans-mitting measurement data within an Internet of Things (IoT) monitoring platform. This configuration is tailored to address the challenges related to the structural integrity of building envelopes. Results demonstrate a potential for a stand-alone solution in the façade sector, but, raising issues for certain limitations, requiring further investigation. In particular, the study emphasizes constraints related to the energy production of PE-EHS for façade integration. It highlights the necessity to carefully consider these limitations within the broader context of their applicability, providing insights for the informed deployment of Piezoelectric Energy Harvesting technology in building envelope monitoring.

Rotational jumps are crucial techniques in sports competitions. Estimating ground reaction forces (GRFs), one of the components constituting jumps, through a biomechanical model-based approach enables analysis even in environments where force plates or machine learning training data cannot be utilized. In this study, rotational jump movements involving twists on land were measured using inertial measurement units (IMUs) and estimated GRFs and body loads using a 3D forward dynamics model. Our estimation method, based on forward dynamics and optimization calculations, generated and optimized body movements using cost functions defined by motion measurements and internal body loads. To reduce the influence of the dynamic acceleration in the optimization calculation, the 3D orientation using sensor fusion composed of acceleration and angular velocity data obtained from IMUs and an extended Kalman filter was estimated. As a result, by generating movements based on the cost function, it was possible to calculate biomechanically valid GRFs while following the measured movements even if not all joints are covered by IMUs. This estimation method allows for 3D motion analysis independent of measurement conditions or training data.

The main purpose of this work was to tests of form and size of fatigue wear of the top layer of oil gear pump wheel (3PW-BPF-24). The object of tests was operated during a determined number of hours at strictly controlled operational and environmental parameters. A microscope of focal differentiation by Alicona InfiniteFocus G4 (with Focus-Variation optical measuring technology) was used for an identification, measurement and description of noticed superficial defects, which resulted from the fatigue process of the top layer and an earlier thermochemical treatment. The work was finished with an analysis of obtained results (based on the analysis of 3D scans) and conclusions concerning about optimization of the thermal treatment. Taking into consideration the presented results (suggestions) in the technology of improving strength properties of gear wheels (of this type oil pumps) may render it possible to obtain an appropriate fatigue endurance of the top layer, i.e. a minimization of observed superficial defects.

To better understand the shape memory materials and self-healing materials, a new series of liquid-crystalline shape memory polyurethane (LC-SMPU) composites, named SMPU-OOBAm, were successfully prepared by incorporating 4-octyldecyloxybenzoic acid (OOBA) into the PEG-based SMPU. The effect of OOBA on the structure, morphology and properties has been carefully investigated. The results demonstrate that SMPU-OOBAm have liquid crystalline properties, triple-shape memory properties and self-healing properties. The incorporated OOBA promotes the crystallizability of both soft and hard segments of SMPU, and the crystallization rate of the hard segment of SMPU decreases when the OOBA-content increases. Additionally, the SMPU-OOBAm forms a two-phase separated structure (SMPU phase and OOBA phase), and it shows two-step modulus changes upon heating. Therefore, the SMPU-OOBAm shows triple-shape memory behavior, and the shape recovery ratio decreases with an increase in the OOBA content. Finally, SMPU-OOBAm shows self-healing properties. The new mechanism can be ascribed to the heating-induced “bleeding” of OOBA in the liquid crystalline state and the subsequent re-crystallization upon cooling. This successful combination of liquid crystalline properties, triple-shape memory properties and self-healing properties make the SMPU-OOBAm composites with many promise applications in smart optical devices, smart electronic devices and smart sensors.

The branch prediction units (BPUs) generally have security vulnerabilities, which can be used by attackers to obtain the execution status, jump directions, and jump address of conditional branches, and the existing protection methods cannot defend against these attacks. Therefore, this article proposes a hardware security protection method for conditional branches of embedded systems. This method calculates the number of updates to the branch target buffer (BTB). When it exceeds the threshold, BTB is locked to prevent attackers from analyzing the execution status of branches based on the time difference of whether BTB is updated. Moreover, the hybrid physical unclonable function (PUF) circuit is designed to provide confidentiality protection for the jump directions, jump addresses, and their indexes, preventing attackers from stealing these critical data. If these mechanism fails and attackers successfully tamper with conditional branches, this paper proposes a control flow integrity (CFI) protection mechanism based on branch labels to timely detect tampering with instruction codes, jump addresses, and jump directions. The proposed method is implemented and tested on FPGA. The experimental results show that this method can achieve fine-grained security protection for conditional branches, with about 5.4% resource overhead and less than 5.5% performance overhead.

Displacement mapping is a computer graphics technique that enables the design of components with regularly or randomly textured surfaces that can be quickly materialized on a three-dimensional (3D) printer when needed. This approach is in principle more flexible, faster and more economical compared to conventional texturing methods, but the accuracy of the texture depends heavily on the parameters used. The purpose of this study is to demonstrate how to produce a surface-textured part using polygonal (mesh) modeling software and a photopolymerizable resin, and to develop a universal methodology to predict the dimensional accuracy of the model file log combined with a resin 3D printer. The printed components were characterized on a scanning confocal microscope. In the setup used in this study, the mesh size had to be reduced to 10% of the smallest feature size and the textured layer had to be heavily (x4) overexposed to achieve the desired accuracy. As a practical application, two functional stamps with a regular (honeycomb) and a random texture, respectively, were successfully manufactured. The insights gained will be of great benefit in quickly and cost-effectively producing components with innovative patterns and textures for a variety of hobby, industrial and biomedical applications.

Microplastics, which are plastic particles smaller than 5 mm in size, are a growing environmental concern since they have been found in oceans, rivers, lakes, and even on land. These tiny particles can escape water filtration systems and end up in water bodies as well as through the degradation of the larger plastic products causing serious environmental and food safety concerns. This research represents the magnitude of this pollution, characterization of microplastic contamination, its type of polymer, and possible sources of this pollution in the rivers around Dhaka, Bangladesh. Quantitative analyses were done following the method suggested by the NOAA and other conventional methods. Among the rivers, Buriganga has the highest microplastic pollution with 3.654 items/L in surface water and 43.125 items/kg in sediment. The concentration in Shitalakshya and Turag rivers are 3.011 items/L and 2.051 items/L in surface water and 34.875 and 17.875 items/kg in sediment respectively. ANOVA test revealed a significant difference between the concentration level of microplastic in the surface water of the Burigana and Turag rivers. A positive correlation between the concentration level of microplastic in the surface water and the sediment was also found. On average 58% of the microplastics were found to be fibrous in surface water. Qualitative analyses were done to find the characteristics and chemical composition of the microplastics. Through the use of FTIR spectroscopy, the study identified different kinds of synthetic polymers in the sample including polyamide (Nylon), polyethylene (PE), polystyrene (PS), polypropylene (PP), polyethersulfone (PES), polyvinyl chloride (PVC), and polyethylene terephthalate (PET) and polyethylene were the most abundant polymer in the samples. This study involved the investigation of three distinct rivers located in the vicinity of Dhaka city

Latin America and the Caribbean offer the most favorable natural and social conditions for the emergence of cattle ranching that regenerate and maintains the ecosystem services on which life on Earth depends, that is energy efficient and that contributes to meeting fundamental human food needs. Unlike other major global producers, cattle farming in Latin America and the Caribbean is fundamentally based on pasture. Therein lies both its strength (due to the regenerative potential of well-managed pastures) and its vulnerability (due to the pervasive link between deforestation and pasture formation, especially in the Amazon, where 40% of the Brazilian herd is concentrated). The diversification of pastures (today marked by impressive monotony, with brachiaria accounting for 85% of the species in Brazil), the introduction of legumes and tree plantations within them, and the proper management of herds, open the way to the possibility of drastically reducing the area currently occupied by the activity (especially in the Amazon) while maintaining the supply of its products. Agricultural research has disseminated forms of moderate intensification of cattle ranching, which represent a low opportunity cost of animal feed and, at the same time, regeneration of ecosystem services that have so far been destroyed by the prevailing methods of farming.

The software industry has adopted component-based software development (CBSD) to rapidly build and deploy large and complex software systems with significant savings at minimal engineering effort, cost, and time. However, CBSD encounters issues on security trust, mainly with respect to dependability attributes. A system is considered dependable when it can produce the outputs for which it was designed with no adverse effect on its intended environment. Dependability consists of several attributes that imply availability, confidentiality, integrity, reliability, safety, and maintainability. Dependability attributes must be embedded in a CBSD model to develop dependable component software. Motivated by the importance of these attributes, this paper pursues two objectives: to design a model for developing a dependable system that mitigates the vulnerabilities of software components, and to evaluate the proposed model. The model proposed in this study is labelled as developing dependable component-based software (2DCBS). To develop this model, the CBSD architectural phases and processes must be framed and the six dependability attributes embedded according to the best practice method. The expert opinion approach was applied to evaluate 2DCBS framing. In addition, the 2DCBS model was applied to the development of an information communication technology (ICT) portal through an empirical study method. Vulnerability assessment tools (VATs) were employed to verify the dependability attributes of the developed ICT portal. Results show that the 2DCBS model can be adopted to develop web application systems and to mitigate the vulnerabilities of the developed systems. This study contributes to CBSD and facilitates the specification and evaluation of dependability attributes throughout model development. Furthermore, the reliability of the dependable model can increase confidence in the use of CBSD for industries.

: In the realm of data management, data preservation stands as a critical undertaking aimed at preserving and upholding the integrity of data. Regardless of whether it concerns personal or enterprise data, the detrimental effects of malicious alterations implemented by attackers cannot be overlooked. Particularly in conventional industrial control environments, the prevalent practice involves the transmission of data from sensors to databases for storage purposes. However, it is essential to recognize that this process exposes the data to various vulnerabilities. Thus, to ensure the long-term security and reliability of the data, it becomes imperative to implement robust data preservation strategies within these industrial control systems. However, the reliance of these databases on physical hard disks introduces inherent vulnerabilities, including the potential for data loss due to disk damage or targeted malicious attacks. Consequently, it becomes imperative to prioritize the implementation of robust data preservation measures. These measures are crucial in mitigating the risk of disruptions and protecting critical data from compromise. By establishing effective data backup systems, employing advanced security protocols, and implementing proactive monitoring mechanisms, organizations can bolster their data preservation capabilities and safeguard against potential threats to data integrity and availability. As a result, many enterprises opt to store their data with third-party providers to ensure data integrity. However, this approach carries inherent risks. If the third-party service experiences an attack or if the data is tampered with, it becomes challenging to verify the integrity of the data. To address these concerns and ensure data preservation within the context of the Internet of Things (IoT), a growing number of individuals are integrating IoT with Distributed Ledger Technology (DLT). By leveraging DLT, the integrity of data can be ensured, reducing reliance on centralized third-party storage and enhancing security in the IoT ecosystem. In this article, IOTA is the DLT, which employs Directed Acyclic Graph (DAG) to store transaction information. Compared to Ethereum or other blockchain technologies, IOTA offers notable advantages in terms of transaction verification speed, making it highly suitable for real-time IoT environments. However, the conventional transmission path from sensors to IOTA nodes entails a complex route, involving multiple hardware devices before reaching the intended destination. This complexity poses challenges in ensuring data integrity during transmission and introduces vulnerabilities such as man-in-the-middle attacks or SQL injection attacks. To address these issues, we propose a method to streamline the transmission path between sensors and IOTA, specifically tailored for industrial fields with numerous IoT devices. Our approach involves preprocessing the data stored on the server using our method before uploading, ensuring data confidentiality, and leveraging IOTA to guarantee data integrity. To achieve the shortest path between IoT and DLT nodes, it becomes necessary to establish IOTA nodes on lower-level devices, such as Raspberry Pi or IoT controllers. By simplifying the transmission path, we can reduce the potential for tampering and enhance overall data security. Implementing our proposed method enables the assurance of data confidentiality and integrity during both transmission and storage on the server, strengthening the trustworthiness of the IoT, and IOTA integration.

In manual maintenance inspections of large-scaled photovoltaic (PV) or rooftop PV systems, several days are required to survey the entire PV field. To improve reliability and shorten the amount of time involved, this study proposes an electrical examination based method for locating multiple faults in the PV array. The maximum power point tracking (MPPT) algorithm is used to estimate the maximum power of each PV panel; this is then compared with metering the output power of PV array. Power degradation indexes are parameterized to quantify the degradation between maximum power and metered output power. Bidirectional hetero-associative memory (BHAM) networks are then used to locate multiple faults within the entire PV field. For a rooftop PV system with two strings, as seen in Figure 1, experimental results demonstrate that the proposed model has computational efficiency for real-time applications and that its algorithm is easily implemented in a mobile intelligent vehicle.

In the conservation of monumental heritage, the collection and utilization of information are of primary importance. The Heritage Building Information Modeling (HBIM) procedure harnesses the potential of three-dimensional models, offering significant advantages in accessing documentation, interoperability, multidimensionality of intervention design, cost evaluation and maintenance management. Attention here is focused on the Certosa di Pisa, a large historical complex built in the 14th century as a monastery of the Carthusian order, currently in a state of deterioration and in need of restoration and re-functionalization. The multifaceted nature of this monumental complex, with its intricate interplay of architectural elements spanning different historical periods and featuring diverse techniques, poses a significant challenge for structural safety assessment. This case study presents an opportunity to explore an HBIM approach to streamline the diagnostic process and facilitate the intervention design phase. The goal is achieved by utilizing an accurate 3D model enriched with data from multiple sources and automating certain operations for structural assessment. The usefulness of the HBIM methodology is highlighted as a valuable tool in the realm of Cultural Heritage structures for both technicians and scholars alike.

Understanding the dynamics of Organic Carbon mineralization is fundamental in forecasting biosphere to atmosphere Net Carbon Ecosystem Exchange (NEE). With this perspective, we developed 3D-CMCC-PSM, a new version of the hybrid Process Based Model 3D‐CMCC FEM where also heterotrophic respiration (R_h) is explicitly simulated. The aim was to quantify NEE as a forward problem, by subtracting Ecosystem Respiration (R_eco) to Gross Primary Productivity (GPP). To do so, we developed a simplification of the Soil Carbon dynamics routine proposed in DNDC [1]. The method calculates decomposition as a function of soil moisture, temperature, state of the organic compartments, and relative abundance of microbial pools. Given the pulse dynamics of soil respiration, we introduced modifications in some of the principal constitutive relations involved in phenology and littering sub-routines. We quantified the model structure related uncertainty in NEE, by running our training simulations over 1000 random parameter-sets extracted from parameters distributions expected from literature. 3D-CMCC-PSM predictability was tested on independent time series for 6 Fluxnet sites. The model resulted in daily and monthly estimations highly consistent with the observed time series. It showed lower predictability in Mediterranean ecosystems, suggesting that it may need further improvements in addressing evapotranspiration and water dynamics.

Throughout history, the pursuit of diagnosing and predicting crop yields has evidenced genetics, environment, and management practices' intertwined roles in achieving food security. However, the sensitivity of crop phenotypes and genetic responses to weather and climate remains unclear, hampering the identification of the underlying abilities of plants to adapt to climate change. We hypothesize that the PAWN global sensitivity analysis (GSA) coupled with a genetic by environment (GxE) model -built of environmental covariance and genetic markers structures- can evidence the contributions of climate on the predictability of maize yields in the U.S. and Ontario, Canada (US-CA). The GSA-GxE modeling framework estimates the relative contribution of climate variables such as solar radiation, temperature, rainfall, and relative humidity on improving maize yield predictions in US-CA. We use an improved version of the Genomes to Fields (G2F) initiative multi-dimensional database to build the environmental covariance matrices for the proposed GSA-GxE framework. The PAWN indices show that the aggregated GxE model’s highest sensitivity levels over US-CA were attributed to solar radiation, temperature, rainfall, and relative humidity. In one-third of the locations, rainfall was the primary climate variable responsible for maize yield predictability. Also, a consistent pattern of top sensitivity indices by location indicates that Relative Humidity, Solar Radiation, and Temperature were distributed as the main or the second most relevant drivers of maize yield predictability.

This paper proposed an optimal tracking control scheme through adaptive dynamic programming(ADP) for a class of partially unknown discrete-time nonlinear systems based on radial basis function neural network(RBF-NN). In order to acquire the unknown system dynamics, we use two RBF-NNs, the one is used to construct the identifier, and the another is used to directly approximate the steady-state control input, where a novel adaptive law is proposed to update neural network weights. While the optimal feedback control and the cost function are derived via feedforward neural networks approximating, it is proposed to regulate the tracking error, the critic network and the actor network are then trained online to obtain the solution of the associated Hamilton–Jacobi–Bellman (HJB) equation being built under the ADP framework. Simulations verify the effectiveness of the optimal tracking control technique using the neural networks.

The human mandible's cancellous bone, which is characterized by its unique porosity and directional sensitivity to external forces, is crucial for sustaining biting stress. Traditional CAD models fail to fully represent bone's anisotropic structure and thus depend on simple isotropic assumptions. For our research, we use the latest versions of nTopology and Creo Parametric software to make biomimetic Voronoi lattice models that accurately reflect the complex geometry and mechanical properties of trabecular bone. The porosity of human cancellous bone is accurately modeled in this work using biomimetic Voronoi lattice models. The porosities range from 70% to 95%, which can be achieved by changing the pore sizes to 1.0 mm, 1.5 mm, 2.0 mm, and 2.5 mm. Finite element analysis (FEA) was used to examine the displacements, stresses, and strains acting on dental implants with a buttress thread, abutment, retaining screw, and biting load surface. The results show that the Voronoi model accurately depicts the complex anatomy of the trabecular bone in the human jaw, compared to standard solid block models. The ideal pore size for biomimetic Voronoi lattice trabecular bone models is 2 mm, taking into account both the von Mises stress distribution over the dental implant, screw retention, cortical bone, cancellous bone, and micromotions. This pore size displayed balanced performance by successfully matching natural bone's mechanical characteristics. Advanced finite element analysis (FEA) improves biomechanical understanding of how bones and implants interact by creating more accurate models of biological problems and dynamic loading situations. This makes biomechanical engineering better.

As the adoption of renewable energy sources grows, ensuring a stable power balance across various time frames has become a central challenge for modern power systems. In line with the "dual carbon" objectives and the seamless integration of renewable energy sources, harnessing the advantages of various energy storage resources and coordinating the operation of long-term and short-term storage have become pivotal directions for future energy storage deployment. To address the complexities arising from the coupling of different time scales in optimizing energy storage capacity, this paper proposes a method for energy storage planning that accounts for power imbalance risks across multiple time scales. Initially, the Seasonal and Trend decomposition using the Loess (STL) decomposition method is utilized to temporally decouple actual operational data. Subsequently, power balance computations are performed based on the obtained data at various time scales to optimize the allocation of different types of energy storage capacities and assess the associated imbalance risks. Finally, the effectiveness of the proposed approach is validated through hourly applications using real-world data from a province in China over recent years.