This paper describes different variants of broadband and simple attenuator modules for beamforming applications, based on Radio Frequency Micro Electro-Mechanical Systems (RF-MEMS), framed within Coplanar Waveguide (CPW) structures. The modules proposed in the first part of this work differ in their actuation voltage, topology, and desired attenuation level. Fabricated samples of basic 1-bit attenuation modules, characterized by a moderate footprint of 690 x 1960 µm2 and aiming at attenuation levels of -2, -3 and -5 dB in the 24.25-27.5 GHz range, are presented in their variants featuring both low actuation voltages (5-7 V) as well as higher values (~ 45V), the latter ones ensuring larger mechanical restoring force (and robustness against stiction). Beyond the fabrication non-idealities that affected the described samples, the substantial agreement between simulations and measurement outcomes proved that the proposed designs could provide precise attenuation levels up to 40 GHz, ranging up to nearly -3 dB and -5 dB for the series and shunt variants, respectively. Moreover, they could be effective building blocks for future wideband and reconfigurable RF-MEMS attenuators. In fact, in the second part of this work, combinations of the discussed cells and other configurations meant for larger attenuation levels will be investigated.

The Microwave Humidity and Temperature sounder (MWHTS) on board the Fengyun (FY)-3C satellite measure the outgoing radiance form the Earth surface and atmospheric constituents. MWHTS makes measurements in the isolated oxygen absorption line near 118 GHz and the vicinity of strong water vapor line around 183 GHz, can provide fine vertical distribution structure of both atmospheric humidity and temperature. However, in order to obtain the accurate soundings of humidity and temperature by the physical retrieval method, bias between the observed radiance and those simulated by radiative transfer model from the background or first guess profiles must be correct. In this study, two bias correction methods are developed through the correlation analysis between MWHTS measurements and air mass identified by the first guess profiles of the physical inversion, one is the linear regression correction (LRC) and the other is neural networks correction (NNC), representing the linear and nonlinear nature between MWHTS measurements and air mass, respectively. Both correction methods have been applied to MWHTS observed brightness temperatures over the geographic area (180° W-180° E, 60° S-60° N). The corrected results are evaluated by the probability density function of the difference between corrected observations and simulated values and the root mean square error (RMSE) with respect to simulated observations. The numerical results show that the NNC method perform better, especially in MWHTS channels 1 and 7-9 whose peak weight function heights are close to the surface. In order to assess the effects of bias correction methods proposed in this study on the retrieval accuracy, a one-dimensional variational system was built and applied to the MWHTS uncorrected and corrected brightness temperatures to estimated atmospheric temperature and humidity profiles, The retrieval results show that the NNC has better performance which is to be expected. An indication of the stability and robustness of NNC method is given which suggests that the NNC method has promising application perspectives in the physical retrieval.

Microwave technology has a potential application in the extraction of zinc from sulphide ores, knowledge of the dielectric properties of these ores plays a major role in the microwave design and simulation for any process. The dielectric properties of zinc sulfide concentrate for two different apparent densities—1.54 and 1.63 g/cm³—have been measured by using the resonance cavity perturbation technique at 915 and 2450 MHz during the roasting process for the temperature ranging from room temperature to 850 °C. The variations of dielectric constant, the dielectric loss factor, the dielectric loss tangent and the penetration depth with the temperature, frequency and apparent density have been investigated numerically. The results indicate that the dielectric constant increases as the temperature increases and temperature has a pivotal effect on the dielectric constant, while the dielectric loss factor has a complicated change and all of the temperature, frequency and apparent density have a significant impact to dielectric loss factor. Zinc sulfide concentrate is high loss material from 450 to 800 °C on the basis of theoretical analyses of dielectric loss tangent and penetration depth, its ability of absorbing microwave energy would be enhanced by increasing the apparent density as well. The experimental results also have proved that zinc sulfide concentrate is easy to be heated by microwave energy from 450 to 800 °C. In addition, the experimental date of dielectric constant and loss factor can be fitted perfectly by Boltzmann model and Gauss model, respectively.

This paper presents for the first time the design of a microwave sensing setup for the potential monitoring and identification of red palm weevil (RPW) gender type. The microwave sensor consists of a planar two-port transmission line (TL) with a single complementary split-ring resonant (CSRR) inclusion etched from the bottom metallic layer. The CSRR sensor is placed on top of a customized non-conductive container. The microwave sensing setup has been designed, numerically demonstrated, fabricated and tested experimentally. Simulated results correlate quite well with the experimental data. Moreover, the sensitivity of the CSRR sensor when in close proximity to different RPW gender has been evaluated both numerically and experimentally. Based on the measured results from 15 RPW collected samples with different body sizes, different RPW gender types showed unique microwave signatures. Notable shift to the sensor's resonance frequency has been achieved, where on average a resonant frequency shift of 10% for adult RPWs was achieved, while 2.4% frequency change was obtained for larvae (young) RPWs. Hence, the proposed microwave sensing setup can be adopted in field trials to examine and differentiate between various RPW genders at various development stages.

This paper compares two types of microfluidic sensors that are designed for operation in ISM bands at microwave frequencies of 2.45 GHz and 5.8 GHz. In the case of the first sensor, the principle of operation is based on the resonance phenomenon in a microwave circuit filled with a test sample. The second sensor is based on the interferometric principle and makes use of the superposition of two coherent microwave signals, where only one of them goes through a test sample. Both sensors are monolithic structures fabricated using low temperature co-fired ceramics (LTCC). The LTCC-based microwave-microfluidic sensor properties are examined and compared by measuring their responses for various concentrations of two types of test fluids: one is a mixture of water/ethanol, and the other is dopamine dissolved in a buffer solution. The experiments show a linear response for the LTCC-based microwave-microfluidic sensors as a function of the concentration of the components in both test fluids.

The article presents the results of evaluating the possibility of conducting radio astronomy studies in the windows of atmospheric transparency ~100, ~230 and ~350 GHz using the optical Big Telescope Alt-Azimuthal (BTA) of the SAO RAS. A list of some promising astronomical tasks is proposed. The astroclimat conditions at the BTA site and possible optical, cryogenic and mechanical interfaces for mounting a superconducting radio receiver at the focus of the optical telescope are considered. As a receiving system, arrays of detectors cooled to ~0.3 K based on the Superconductor – Insulator – Normal metal – Insulator – Superconductor (SINIS) structure are proposed. The implementation of the project will make it possible to use the BTA site of the SAO RAS not only to solve some astronomical problems (it is possible to consider the implementation of a single observatory, the VLBI mode in the Suffa, EHT and Millimetron projects), but will also be used to test various cryogenic detectors in a real observatory.

A challenge in building large-scale superconducting quantum processors is the precise control and manipulation of the qubit state. However, the crosstalk between the microwave control lines impedes the parallel execution of high-fidelity digital and analog quantum operations. Here, we propose and demonstrate a universal compensation protocol for calibrating the microwave signal crosstalk. We also introduce amplified error sequences to optimize the accuracy. Furthermore, we show a definitive improvement in parallel gate operations with crosstalk cancellation, demonstrating the technique's effectiveness. This work paves the way for superconducting hardware that features automated calibration of microwave crosstalk, leading to enhanced fidelities in multiqubit circuits.

In this paper, we introduce a specialized, fully automated experimental arrangement designed for assessing the effectiveness of augmented and virtual reality technologies in healthcare setting and explore its design principles focusing on depth sensor characterization. The main goal of this project is to establish a robust benchtop platform for the quantitative evaluation of extended reality technologies in a controlled environment, emphasizing the practical assessment of augmented reality head-mounted devices. We outline a design concept and considerations for an experimental configuration aimed at creating a realistic testing environment. This apparatus comprises an observation platform mounted on a three-degree-of-freedom motorized system and a test phantom stage. Focusing on real-case scenarios, we utilized a range of sensors, including readily available range-sensing cameras and commercial augmented reality headsets, such as the Intel RealSense L515 LiDAR camera, mounted on the motion control system. The setup enabled automated data collection and facilitates controlled assessments and validation of various facets of augmented reality technologies, including object, hand, and head tracking, as well as static and dynamic image registration. This paper describes the system architecture, the process of automated data collection, and presents several evaluation studies conducted with this setup, providing insights into the quality and temporal noise associated with static or moving objects or observers in augmented reality applications.

Among the various types of gas sensors, the chemoresistive gas sensors based on metal oxides are considered the most attractive ones due to their simple operation, low costs and miniaturization. Thin films of V2O5 undoped and doped with TiO2 were studied as nitrogen dioxide, methane and hydrogen sensors. The experimental kinetics of the electrical conductivity changes due to introduction and removal of gas on metal oxide gas sensors were successfully explained in terms of the Langmuir adsorption theory.

Solvent free copolymerization of epoxides derived from fatty acid esters of waste cooking oil with phthalic anhydride using (salen)CrIII Cl as catalyst and n-Bu4NCl/DMAP as co-catalyst was carried out for the first time under microwave irradiation, where reaction time was reduced from number of hours to minutes. The polyesters were obtained with molecular weight (Mw = 3084-6740 g/mol) and dispersity values (D = 1.18-1.92), when (salen)CrIII Cl/n-Bu4NCl was used as catalysts. While in case of DMAP as a co-catalyst, polyesters with improved molecular weight (Mw = 5537-6925 g/mol) and narrow dispersity values (D = 1.07-1.28) were obtained even at reduced concentrations of (salen)CrIII Cl and DMAP. The obtained products were characterized and evaluated by attenuated total reflection-fourier transform infrared spectroscopy (ATR-FTIR), proton nuclear magnetic resonance (1H-NMR) spectroscopy, gel permeation chromatography (GPC) and thermogravimetric analysis (TGA) Techniques.

Focused microwave breast hyperthermia (FMBH) employs a phased antenna array to perform beamforming that can focus microwave energy at targeted breast tumors. Selective heating of the tumor endows the hyperthermia treatment with high accuracy and low side effects. The effect of FMBH is highly dependent on the applied phased antenna array. This work investigates the effect of polarizations of antenna elements on the microwave focusing results by simulations. We explore two kinds of antenna arrays with the same number of elements using different digital realistic human breast phantoms. The first array has all the elements’ polarization in the vertical plane of the breast while the second array has half elements’ polarization in the vertical plane and the other half in the transverse plane, i.e., cross polarization. In total 96 sets of different simulations are performed, and the results show that the second array leads to a better focusing effect in dense breasts than the first array. This work is very meaningful for the potential improvement of the antenna array for FMBH, which is of great significance for the future clinical applications of FMBH. The antenna array with cross polarization can also be applied in micro-wave imaging and sensing for biomedical applications.

Many fields of human activity benefit from the ability to create images of obscured objects placed behind walls and to map their displacement in a noninvasive way. Usually, imaging devices like Synthetic Aperture Radars (SAR) and Ground Penetrating Radars (GPR) use expensive dedicated electronics which results in prohibitive prices. This paper presents the experimental implementation and the results obtained from an imaging system capable of performing SAR imaging and interferometric displacement mapping of targets located behind walls, as well as 3D GPR imaging using a low-cost general-purpose radar sensor. The proposed solution uses for the RF section of the system a K-band microwave radar sensor module implementing Frequency Modulated Continuous Wave operation. The low-cost sensor was originally intended for simple presence detection and ranging for domestic applications. The proposed system was tested in several scenarios and proved to operate as intended for a fraction of the cost of a commercial imaging device.

The carbonyl iron particles were dispersed in a polychloroprene rubber (CR) matrix under an external magnetic field for practical application as microwave absorption composites film. The film prepared under external magnetic field with a thickness of only 0.54 mm showed least reflection loss of -15.98 dB and the reflection loss value less than -10.0 dB over the frequency range of 11.4~14.8 GHz. In comparison with the microwave absorption properties of calculation by transmission line theory based on the tested relative complex permittivity and permeability and film prepared by general route without external magnetic field, the film made with external magnetic field exhibited more excellent microwave absorption properties, strongly depending on the increment of anisotropy and rearrangement of magnetic particles. The results indicated the composite film made under external magnetic field have excellent microwave absorption properties, which suggest that the composites thin film could be used as a thinner and lighter microwave absorber.

This review delves into the growing field of flexible and stretchable strain sensors utilized in human gait analysis, focusing on determining knee bending angle and muscle activities when a human subject walks. Recent advancements have enabled these sensors to accurately capture biomechanical parameters while accommodating the body's natural movements. We examine the principles underlying these sensors' design and fabrication techniques, emphasizing their flexibility, stretchability, and biocompatibility for seamless integration into wearable systems. Through critical evaluation of existing methodologies, we assess the reliability and validity of these sensors in quantifying gait parameters. Furthermore, we discuss this technology's clinical and research implications, highlighting its potential in personalized rehabilitation and sports performance optimization. We provide an overview of flexible strain sensors and their application for analyzing human walking gait, especially for observing walking gait in rehabilitation programs. First, we present the basic working principles of various flexible strain sensors. Second, by the application of flexible strain sensors as walking gait monitoring. Finally, current challenges and future opportunities in this research area are discussed. By synthesizing current knowledge and outlining future directions, this review aims to provide insights for researchers and practitioners seeking to leverage flexible and stretchable strain sensors for comprehensive human gait analysis.

Microwave radiation diagnosis technology can detect thermal changes in skin tissue earlier than anatomical changes, but its detection accuracy is limited by non-target radiation interference in the measurement environment, additional measurement errors of system units, and energy scattering and transmission between skin tissues. This paper aims to address the scientific challenges of analyzing the forward and inversion modelling detection mechanism of layered accurate temperature measurement of human skin tissue based on multi-band. The study focuses on the construction of a pencil beam antenna optimization system, the optimization strategy of high-sensitivity correlated radiometer architecture, and the high-precision multi-band forward and inversion modelling detection algorithm. The key technologies include: (1) A new method of integrated modeling and multi-index optimization of antenna with high directivity and small aperture is proposed, and a priori knowledge-guided neural network of pencil beam distribution is constructed to realize the inversion model of antenna structural parameters; (2) The influence mechanism of high sensitivity correlated radiometer architecture error is analyzed, and a periodic phase shift error correction algorithm based on uniform polar circle is designed; (3) Combining deep learning theory and hyperparameter optimization framework, an iterative model is established, and the objective function modified by the penalty factor is defined to realize a new detection method combining forward and inversion. This paper presents a theoretical foundation for the industrialization of microwave radiation diagnostic technology.

Among magnetoelectric (ME) heterostructures, ME laminates of the type Metglas-like / PVDF (magnetostrictive+piezoelectric constituents) have shown the highest induced ME voltages, usually detected at the magnetoelastic resonance of the magnetostrictive constituent. This ME coupling happens because of the high cross-correlation coupling between magnetostrictive and piezoelectric material, and is usually associated with a promising application scenario for sensors or actuators. In this work we detail the basis of the operation of such devices, as well as some arising questions (as size effects) concerning their best performance. Also, some examples of their use as very sensitive magnetic fields sensors or innovative energy harvesting devices will be presented At the end, the challenges, future perspectives and technical difficulties that will determine the success of ME composites for sensor applications are discussed.

In this work, an innovative numerical approach for polylinear approximation (polylinearization) of non-self-intersecting compact sensor characteristics (transfer functions) specified either pointwise or analytically is introduced. The goal is to optimally partition the sensor characteristic, i.e. to select the vertices of the approximating polyline (approximant) along with their positions on, the sensor characteristics so that the distance (i.e. the separation) between the approximant and the characteristic is rendered below a certain problem-specific tolerance. To achieve this goal, two alternative non-linear optimization problems are solved, whose essential difference is in the adopted quantitative measure of the separation between the transfer function and the approximant. In the first problem, which relates to absolutely integrable sensor characteristics (their energy is not necessarily finite, but they can be represented in terms of convergent Fourier series), the polylinearization is constructed by numerical minimization of the L^1--metric (a distance-based separation measure), concerning the number of polyline vertices and their locations. In the second problem which covers the quadratically integrable sensor characteristics (whose energy is finite, but they do not necessarily admit a representation in terms of convergent Fourier series), the polylinearization is constructed by minimizing numerically the L^2-metric (area-, or energy-based separation measure) for the same set of optimization variables –the locations, and the number of polyline vertices.

Plant leaf area index (LAI) is a key characteristic affecting field canopy microclimate. In addition to traditional professional measuring instruments, smartphone camera sensors have been used to measure plant LAI. However, when smartphone methods were used to measure conifer forest LAI, very different performances were obtained depending on whether the smartphone was held at the zenith angle or at a 57.5° angle. To validate further the potential of smartphone sensors for measuring conifer LAI and to find the limits of this method, this paper reports the results of a comparison of two smartphone methods with an LAI-2000 instrument. It is shown that both methods can be used to reveal the conifer leaf-growing trajectory. However, the method with the phone oriented vertically upwards always produced better consistency in magnitude with LAI-2000. The bias of the LAI between the smartphone method and the LAI-2000 instrument was explained with regard to four aspects that can affect LAI: gap fraction, leaf projection ratio, sensor field of view (FOV), and viewing zenith angle (VZA). It was concluded that large FOV and large VZA cause the 57.5° method to overestimate the gap fraction and hence underestimate conifer LAI, especially when tree height is greater than 2.0 m. For the vertically upward method, the bias caused by the overestimated gap fraction is compensated for by an underestimated leaf projection ratio.

Single-phase-to-ground fault in non-effectively grounded systems poses serious public safety concern. Along with increasing deployment of low-voltage (LV) sensors, new opportunities and ways are created for solving this traditional problem in distribution systems. A new approach, identifying primary single-phase-to-ground line fault and locating it through measurement data from smart sensors deployed in the secondary side of distribution transformers, is proposed in this paper. When a fault occurs in primary distribution feeder, the transient aerial mode voltage (AMV) of each LV smart sensor is calculated. The fault line can be identified by an abrupt change value of AMV at LV side. Next, by finding the position of the maximum value of this AMV from LV sensors on the fault line, the fault location can be pinpointed to two neighboring distribution transformers. The proposed method has been proven to be efficient and reliable by simulation studies.

Contaminants of Emerging Concern (CECs), a new category of contaminants in limelight, is a major issue of global concern. The pervasive nature of CECs and its harmful effects, such as cancer, reproductive disorders, neurotoxicity etc., make the situation alarming. The perilous nature of CECs lies in the fact that even very small concentration of CECs can cause great impacts on living beings. It also has a nature of bioaccumulation. Thus, it is the ultimate need to have efficient sensors for detection of CECs to ensure safe living environment. Electrochemical sensors are an efficient platform for CEC detection as they are highly selective, sensitive, stable, reproducible, and prompt, and can detect very low concentrations of analyte. Major classes of CECs are pharmaceuticals, illicit drugs, personal care products, endocrine disruptors, newly registered pesticides, and disinfection by-products. This review focusses on CECs, including their sources and pathways, health effects caused by them, and electrochemical sensors as reported in literatures under each category for the detection of major CECs.

Structural deformations are one of the most significant factor that affects machine tool (MT) positioning accuracy. These induced errors are complex to be represented by a model, nevertheless they need to be evaluated and predicted in order to increase the machining performance. This paper presents a novel approach to calibrate a machine tool in real-time, analyzing the thermo-mechanical errors through Fibre Bragg Grating (FBG) sensors embedded in the MT frame. The proposed configuration consists of an adaptronic structure of passive materials, Carbon Fibre Reinforced Polymers (CFRP), equipped by FBG sensors that are able to measure in real-time the deformed conditions of the frame. By using a proper thermo-mechanical kinematic model, the displacement of the end effector may be predicted and corrected when it is subjected to external undesired factors. By starting from a set of FE simulations to develop a model able to describe the MT structure stresses, a prototype has been fabricated and tested. The scope was to compare the numerical model with the experimental tests using FBG sensors. The experimental campaign has been performed varying the structure temperature over time and measuring the tool tip point (TTP) positions. The obtained results showed a substantial matching between the real and the predicted position of TTP confirming the effectiveness of the proposed calibration system.

This study presents the utilization of the Microwave InfraRed Thermography (MIRT) technique to identify and analyze the defects in the carbon-fiber-reinforced polymer (CFRP) composite rein-forcement of concrete specimens. At first, a set of the numerical models was created, comprising of the broadband pyramidal horn antenna and the analyzed specimen. The utilization the system operating at a power of 1000W in a continuous mode, operating at frequency of 2.45 GHz was analyzed. The specimen under examination comprised a compact concrete slab that was covered with an adhesive layer, thereafter, topped with a layer of CFRP. An air gap represented a defect at the interface between the concrete and CFRP within the adhesive layer. In the modelling stage the study investigated three separate scenarios: a sample with no defects, a sample with a defect located at the center, and a sample with a numerous additional random defects located at the rim of the CFRP matte, to analyze the effect of the natural reinforcement degradation in this area. The next phase of the study involved conducting experiments to confirm the results obtained from nu-merical modeling. In the experiments the concrete sample aged for 10 years with the defect in the center and naturally developed defects at the CFRP rim was used. The study employed numerical modeling to explore the phenomenon of microwave heating in complex structures. The aim was to assess the chosen antenna design and identify the most effective experimental setup. These con-clusions were subsequently confirmed through experimentation. The observations made during the heating process were particularly remarkable, since they deviated from earlier studies that solely conducted measurements of the sample post-heating phase. The findings demonstrate that MIRT has the capacity to be employed as a technique for detecting flaws in concrete structures reinforced with CFRP.

In mining machines with friction discs, but also in multi-rope traction elevators, it is necessary to distribute the applied tensile load, generated by the weight of the cage and counterweight, evenly in all cross-sections of the load-bearing ropes. Hydraulic devices used for this purpose can operate on the principle of Pascal's law. The article presents a structural design, a 3D model and an implemented solution of a laboratory device capable of simulating a practical method of evenly distributing the total weight of the load into partial tensile forces of the same size acting on a selected number of load-bearing ropes. The laboratory equipment uses two pairs of three steel cables of finite length for the simulations. During the experimental measurements, tensile forces derived from the tractive force of the piston rods, pushed into the bodies of the hydraulic cylinders by the pressure of the hydraulic oil supplied through the pipeline under the pistons of the hydraulic cylinders, were detected. The resulting amount of hydraulic oil pressure in the hydraulic circuit influenced by different values of the hydraulic oil pressures in the hydraulic cylinders and by the pressure in the supply pipe was experimentally studied on the laboratory equipment. Simulations were also carried out in order to detect the hydraulic oil pressure in the hydraulic circuit caused by the change in the different magnitudes of the tensile forces in the ropes From the experiments carried out, it follows that with the appropriate choice of hydraulic elements and the design of the hydraulic circuit, the weight of the load, acting as the total pulling force in the ropes, can be evenly distributed (with a deviation of up to 5%) to all cross-sections of the load-bearing ropes. If the exact values of the hydraulic oil volumes under the pistons of all hydraulic cylinders are not known, it is not possible to calculate the pressure values in the hydraulic circuit when the valves of the hydraulic pipes are gradually opened.

We report a broadband radio frequency (RF) channelizer with up to 92 channels using a coherent microcomb source. A soliton crystal microcomb, generated by a 49 GHz micro-ring resonator (MRR), is used as a multi-wavelength source. Due to its ultra-low comb spacing, up to 92 wavelengths are available in the C band, yielding a broad operation bandwidth. Another high-Q MRR is employed as a passive optical periodic filter to slice the RF spectrum with a high resolution of 121.4 MHz. We experimentally achieve an instantaneous RF operation bandwidth of 8.08 GHz and verify RF channelization up to 17.55 GHz via thermal tuning. Our approach is a significant step towards the monolithically integrated photonic RF receivers with reduced complexity, size, and unprecedented performance, which is important for wide RF applications ranging from broadband analog signal processing to digital-compatible signal detection.

Membrane-based sensors (MePSs) exhibit remarkable precision and sensitivity in detecting pressure changes. MePSs are commonly used to monitor catalytic reactions in solution, generating gas products crucial for signal amplification in bioassays. They also allow catalyst quantification by indirectly measuring the pressure generated by the gaseous products. This is particularly interesting to detect enzymes in biofluids associated with disease onset. To enhance the performance of a MePS, various structural factors influence membrane flexibility and response time, ultimately dictating the device's pressure sensitivity. In this study, we fabricated MePSs using polydimethylsiloxane (PDMS) and investigated how structural modifications affect the Young's modulus (E) and residual stress (σ0) of the membranes. These modifications have a direct impact on the sensors' sensitivity to pressure variations, observed as a function of the volume of the chamber (Σ) or of the mechanical properties of the membrane itself (S). MePSs exhibiting the highest sensitivities were then employed to detect catalyst quantities inducing the dismutation of hydrogen peroxide, producing dioxygen as gaseous product. As a result, catalase enzyme was successfully detected using these optimized MePSs, achieving a remarkable sensitivity of (22.7 ± 1.2) µm/nM and a limit of detection (LoD) of 396 pM.

We report a photonic-based radio frequency (RF) arbitrary waveform generator (AWG) using a soliton crystal micro-comb source with a free spectral range (FSR) of 48.9 GHz. The comb source provides over 80 wavelengths, or channels, that we use to successfully achieve arbitrary waveform shapes including square waveforms with a tunable duty ratio ranging from 10% to 90%, sawtooth waveforms with a tunable slope ratio of 0.2 to 1, and a symmetric concave quadratic chirp waveform with an instantaneous frequency of sub GHz. We achieve good agreement between theory and experiment, validating the effectiveness of this approach towards realizing high-performance, broad bandwidth, nearly user-defined RF waveform generation.

The goal of this research is to determine the optimal microwave-assisted sol-gel synthesis pa-rameters of TiO2 nanoparticles with the achievement of the crystalline TiO2 nanoparticles with the highest specific surface area and the lowest energy band gap. Titanium isopropoxide was used as a precursor to prepare the sol (colloidal solution) of TiO2, isopropanol as a solvent, acetylacetone for complexation, and nitric acid as a catalyst. Four samples of titanium dioxide were synthesized from the prepared colloidal solution in a microwave reactor at a temperature of 150 °C for 30 minutes and at a temperature of 200 °C for 10, 20, and 30 minutes. The phase composition of the prepared samples was determined by X-ray diffraction analysis (XRD) and Fourier-transform infrared spectroscopy (FTIR). Nitrogen adsorption/desorption isotherms were used to determine the spe-cific surface area and pore size distributions by Brunauer-Emmett-Teller (BET) method. The band gap energy values of the TiO2 samples were determined by diffuse reflectance spectroscopy (DRS). CrystallineTiO2 nanoparticles with the highest specific surface area and the lowest energy band gap were obtained for the TiO2 sample synthesized at 200 °C for 10 minutes.

In food industry, there is a growing demand for cost-effective methods for inline inspection of food items able to non-invasively detect small foreign bodies which may have contaminated the product during the production process. Microwave imaging may be a valid alternative to the existing technologies, thanks to its inherently low-cost and its capability of sensing low-density contaminants. In this paper, a low-complexity microwave imaging system specifically designed to enable the inspection of a large variety of food products is presented. The system consists of two Circularly Loaded Antipodal Vivaldi Antennas, having a very large operative band, from 1 to 15 GHz, thus allowing a suitable spatial resolution for different food products from mostly fatty to high water-content ones. The antennas are arranged in such a way to collect the signal useful to exploit a recently proposed real-time microwave imaging strategy, leveraging the inherent symmetries usually characterizing food items. The system is experimentally characterized, and the achieved results compare favorably with the design specifications and the numerical simulations. Relying on these positive results, a first experimental proof of the effectiveness of the whole system is presented, which confirms its efficacy.

This paper comprehensively reviews sensors and sensing devices developed or/and proposed so far utilizing two smart materials: electrorheological fluids (ERFs) and magnetorheological materials (MRMs) whose rheological characteristics such as stiffness and damping can be controlled by external stimuli, an electrical voltage for ERFs and a magnetic field for MRMs, respectively. In this review article, the MRMs are classified into magnetorheological fluid (MRF), magnetorheological elastomer (MRE) and magnetorheological plastomer (MRP). To easily understand the history of sensing research using the two smart materials, the order of this review article is organized in a chronological manner of ERF sensors, MRF sensors, MRE sensors and MRP sensors. Among many sensors fabricated from each smart material, one or two sensors or sensing devices are adopted to discuss on the sensing configuration, working principle and specifications such as accuracy and sensitivity. Some sensors adopted in this article include force sensor, tactile device, strain sensor, wearable bending sensor, magnetometer, display device and flux measurement sensor. After briefly describing what have been reviewed in a conclusion, several challenging future works, which should be done for practical applications as sensors or sensing devices, are remarked in terms of new technologies such as artificial intelligence neural network in which several parameters affecting the sensor signals can be precisely tuned or controlled. It is sure that this review article is very helpful to make creative sensors using not only the proposed smart materials but also several different types of smart materials including shape memory alloys and active polymers.

Microwave technology, foundational in quantum computing, utilizes precise control of quantum states via microwave pulses to manage quantum bits (qubits). This review explores the potential of leveraging these principles in neuroscience, where such technology could enable novel approaches to imaging, diagnosing, and treating neurological disorders. By comparing the techniques used in quantum computing with potential applications in neural circuit manipulation and brain activity monitoring, we highlight both the promising synergies and the significant challenges at the intersection of these fields. This interdisciplinary exploration not only underscores the transformative potential of microwave technology in neuroscience but also addresses the ethical considerations and technological hurdles that accompany the integration of advanced quantum mechanics into biological contexts. The convergence of microwave technology with neural science opens a pathway for breakthroughs in understanding and treating complex brain disorders, advocating for a cautious yet optimistic approach towards future research and application.

Breast cancer prevention is very important for a woman's health worldwide. We have demonstrated a correlation between mammography and ultrasound with diagnoses using passive microwave radiometry (MWR) and a miRNA oncopanel. While mammography screening dynamics could be completed in 3-6 months, MWR will provide us with a prediction in a matter of weeks or even days with the potential for complementary miRNA diagnostics. An early breast cancer diagnosis may be accomplished using either one of these novel techniques alone or in conjunction with more established techniques

Sensors and actuators are fundamental units in Cyber-Physical and Internet of Things systems. Because they are included in a variety of systems, using many technologies, it is very useful to characterize their functions abstractly by describing them as Abstract Entity Patterns (AEPs), that are patterns that describe abstract conceptual entities. For concreteness, we study them here in the context of autonomous cars. An autonomous car is a complex system because, in ad-dition to its own complex design, it interacts with other vehicles and with the surrounding in-frastructure. To handle these functions, it must incorporate various technologies from different sources. An autonomous car is an example of a Cyber-Physical System, where some of its func-tions are performed by Internet of Things units. Sensors are extensively used in autonomous cars to measure physical quantities; actuators are commanded by controllers to perform appro-priate physical actions. From AEPs we can derive concrete patterns, a structure combining re-lated AEPs is an Entity Solution Frame (ESF). Both sensors and actuators are susceptible to mali-cious attacks due to the large attack surface of the system where they are used. Our work is in-tended to make autonomous cars more secure, which also increases their safety. Our final objec-tive is to build a Security Solution Frame for sensors and actuators of autonomous cars that will facilitate their secure design. A Security Solution Frame is a solution structure that groups to-gether and organizes related security patterns. This article is the first stage of a secure unit that can be used to design not only secure autonomous cars but also any system where sensors and actuators are used. This paper concentrates on AEPs and ESFs for sensors and actuators; that is, on the functional aspects of these devices.

Magnetic sensors are widely used in health management systems for turbomachinery, but their applications in the hot zone are limited due to the loss of magnetic properties by permanent magnets with increasing temperature. The paper presents and verifies models and design solutions aimed at improving the performance of an inductive sensor for measuring the motion of rotating objects operating at elevated temperatures (200-1000C), such as compressor and turbine blades. Physical, analog and mathematical models of the interaction of blades with the sensor were developed. A prototype of the sensor was made and its tests were carried out on the RK-4 rotor rig for the speed of 7000 rpm, in which the temperature of the sensor head was gradually increased to 1100C. The sensor signal level was compared to that of an identical sensor operating at room temperature. The heated sensor works continuously producing the output signal whose level does not change significantly. What is more, a set of six probes passed an initial engine test in an SO-3 turbojet. It was confirmed that the proposed design of the inductive sensor is suitable for blade health monitoring of the last stages of compressors, steam turbines as well as previous generation gas turbines operating below 1000C, even without a dedicated cooling system. In real-engine applications, sensor performance will depend on how the sensor is installed and the available heat dissipation capability

Plasmonic sensors exploiting the Localized Surface Plasmon Resonance (LSPR) of noble metal nanoparticles are common in the visual spectrum. However, for bio-sensors the near infra-red (NIR) windows (600 nm – 900 nm and 1000 nm -1400 nm) are of interest, as it is a region where the absorption coefficient of water, melaninm deoxy- and hemoglobin are all low. The first part of this paper reviews the work that has been undertaken on using gold (Au) and silver (Ag) particles in Metal Enhanced Fluorescence (MEF) in the NIR. Despite this success there are limitations, as there is only a narrow band in the visual and NIR where losses are low for traditional plasmonic materials. Further, noble metals are not compatible with standard silicon manufacturing processes, making it challenging to produce on-chip integrated plasmonic sensors with Au or Ag. Therefore, it is desirable to use different materials for plasmonic chemical and biological sensing, that are foundry-compatible with silicon (Si) and germanium (Ge). One material that has received significant attention is highly doped Ge which starts to exhibit metallic properties at a wavelength as short as 6 μm. This is discussed in the second part of the paper and the results of recent analysis are included.

A planar microwave sensor devoted to the detection of humidity in underwear and clothes in general is proposed. The ultimate goal of the sensor is to detect the presence of liquids in fabrics, of interest to aid patients that suffer from certain pathologies, such as hyperhidrosis and enuresis. The main target in the design of the sensor, considering the envisaged application, is simplicity. Thus, the sensor operates at a single frequency, and the working principle is the variation in the mag-nitude of the transmission coefficient of a matched line loaded with an open-ended quar-ter-wavelength sensing stub resonator. The stub, which must be in contact with the so-called fabric under test (FUT), generates a notch in the transmission coefficient with a resonance frequency that depends on the humidity level of the fabric. By designing the stub with a moderately high quality factor, the variation in the resonance frequency causes a significant change in the magnitude level at the operating frequency, the resonance frequency when the sensing stub is loaded with the dry fabric, and the presence of liquid can be detected by means of an amplitude detector. A prototype device is proposed and experimentally validated.

Isotope detection and identification is paramount in many fields of science and industry, such as in the fusion and fission energy sector, in medicine and material science, and in archeology. The isotopic information provides fundamental insight on the research questions related to these fields as well as insight on product quality and operational safety. However, isotope identification with the established mass-spectrometric methods is laborious and requires laboratory conditions. In this work, Microwave-Assisted Laser-Induced Breakdown Spectroscopy (MW-LIBS) is introduced for isotope detection and identification utilizing radical and molecular emission. The approach is demonstrated with stable B and Cl isotopes in solids and H isotopes in liquid using emission from BO and BO2, CaCl, and OH molecules, respectively. MW-LIBS utilizes the extended emissive plasma lifetime and molecular emission signal integration times up to 900 s to enable use of low ~4 mJ ablation energy without compromising signal intensity and, consequently, sensitivity. On the other hand, long plasma lifetime gives time for molecular formation. Increase in the signal intensity towards the late microwave-assisted plasma was prominent in BO2 and OH emission intensities. As MW-LIBS is online-capable and requires minimal sample preparation, it is an interesting option for isotope detection in various applications.

A microwave assisted method for synthesis of 2-substituted benzimidazoles has been developed. The combination of molar ratio N-phenyl-o-phenylenediamine:benzaldehyde (1:1) using microwave irradiation and only 1% mol of Er(OTf)3 provide an efficient, environmental and mild access to a diversity of benzimidazoles under solvent-free conditions.

In this research, the other reasonable explanations for the cosmic microwave background radiation is revealed. Due to the microwave resolution, it very roughly shows the image of galaxies in the universe. Moreover, the intensity measurement on each pixel of the image is the sum of the incident microwaves from different directions, so the microwave image cannot represent the microwave sources clearly far away from the Earth. Hence, we propose a simulation after removing several strongest microwave sources, the remaining microwave radiation sources can establish a very uniform intensity distribution over a range of several ten light years. On the other hand, Sloan Digital Sky Survey reveals 200 million galaxies in the universe and, in fact, only to eliminate the contributions of all galaxies from the microwave image is impossible. The way to further obtain the fine-scale structure by only removing the few strongest microwave sources as the foreground effect will keep the other contributions from all the rest galaxies and stars. Therefore, the Cosmic Microwave Background cannot be uniquely explained the radiation which was left after the initial formation of the universe. Moreover, it is the mainly residual radiation from the un-calculated galaxies and inaccurate estimation of the microwave source strength.

This paper presents an alternative process to fabricate flexible bandpass filters by using embroidered yarn conductor on electronic-textile. The novelty of the proposed miniaturized filter is its complete integration on the outfit, with benefits in terms of compressibility, stretch ability and high geometrical accuracy, opening the way to develop textile filters in sport and medicine wearable applications. The proposed design consists of a fully embroidered microstrip topology with a length equal to quarter wavelength (λ/4) to develop a bandpass filter frequency response. A drastic reduction in size of the filter was achieved by taking advantage of a simplified architecture based on meandered-line stepped impedance resonator. The e-textile microstrip filter has been designed, simulated, fabricated and measured, with experimental validation at a 7.58 GHz frequency. The insertion loss obtained by simulation of the filter is substantially small. The return loss is greater than 20 dB for bands. To explore the relations between physical parameters and filter performance characteristics, theoretical equivalent circuit model of the filter constituent components were studied. The effect of bending of the e-textile filter is also studied. The results show that by changing the radius of bending up to 40 mm, the resonance frequency is shifted up 4.25 MHz/mm.

The world is facing a great technological transformation towards full autonomous vehicles, where optimists predict that by 2030, autonomous vehicles will be sufficiently reliable, affordable and common to displace most human driving. To cope with these trends, reliable perception systems must enable vehicles to hear and see all the surroundings, being light detection and ranging (LiDAR) sensors a key instrument for recreating a 3D visualization of the world in real time. However, perception systems must rely in accurate measurements of the environment. Thus, sensors must be calibrated and benchmarked before being placed on the market or assembled in a car. This article presents an Evaluation and Testing Platform for Automotive LiDAR sensors with the main goal of testing not only commercially available sensors, but also sensor prototypes currently under development in Bosch Automotive Electronics division. The testing system can benchmark any LiDAR sensor under different conditions, recreating the expected driving environment to which such devices are normally subjected. To characterize and validate the sensor under test, the platform evaluates several parameters such as the field of view (FoV), angular resolution, sensor’s range, etc. This project results from a partnership between the University of Minho and Bosch Car Multimedia Portugal, S.A.

This paper present a platform for airborne sensor applications using low-cost, open-source components carried by an easy-to-fly unmanned aircraft vehicle (UAV). The system, available in open-source [1], is designed for researchers, students and makers for a broad range of their exploration and data-collection needs. The main contribution is the extensible architecture for modularized airborne sensor deployment and real-time data visualisation. Our open-source Android application provides data collection, flight path definition and map tools. Total cost of the system is below 800 dollars. The flexibility of the system are illustrated by mapping the location of Bluetooth beacons (iBeacons) on a ground field and by measuring water temperatures in a lake.

DEXTER (Detection of EXplosives and firearms to counter TERrorism) is a project funded by NATO’s Science for Peace and Security (SPS) program with the goal of developing an integrated system capable of remotely and accurately detecting explosives and firearms in public places without impeding the flow of pedestrians. The active microwave component of the DEXTER project is referred to as MIC (Microwave Imaging Curtain), supported by the French SGDSN (General Secretariat of Defense and National Security), and utilizes a radar system capable of generating 3D images in real time to address non-checkpoint detection of explosives and fire-arms. The project, led by the ONERA (France), is based on a radar imaging system developed by the Fraunhofer FHR institute, using a MIMO architecture with an Ultra Wide-Band waveform. Although high-resolution 3D microwave imaging is already being used in expensive body scanners to detect firearms concealed under clothing, MIC's innovative approach lies in utilizing a high-resolution 3D imaging device that can detect larger dangerous objects carried by moving individuals at a longer range, in addition to providing discrete detection in pedestrian flow. Automatic detection and classification of these dangerous objects is carried out on 3D radar im-ages using a deep-learning network. This paper will outline the project's objectives and constraints, as well as the design, architecture, and performance of the final system. Additionally, it will present real-time imaging results ob-tained during a live demonstration in a relevant environment.

Electro-optic modulator (EOM) is one of the key devices of high-speed optical fiber communication system and ultra-wideband microwave photonic system. Silicon-organic hybrid (SOH) integration platform combines the advantages of silicon photonics and organic materials, providing a high electro-optic effect and compact structure for photonic integrated devices. In this paper we present a SOH integrated EOM with comprehensive investigation of EOM structure design, silicon waveguide fabrication with Slot structure, on-chip poling of organic electro-optic material, and characterization of EO modulation response. The SOH integrated EOM is measured with 3dB-bandwidth of over 50 GHz and half-wave voltage length product of 0.26 V·cm. Furthermore, we demonstrate a microwave photonics phase shifter by using the fabricated SOH integrated dual parallel Mach-Zehnder modulator. The phase shift range of 410 degree is completed from 8 GHz to 26 GHz with a power consumption of less than 38 mW.

Since the systematic evolution of ligands by exponential enrichment (SELEX) method was developed, aptamers have made significant contributions as bio-recognition sensors. Microdevice systems allow for low reagent consumption, high-throughput of samples, and disposability. Due to these advantages, there has been an increasing demand to develop microfluidic-based aptasensors for analytical technique applications. This review introduces the principal concepts of aptasensors and then presents some advanced applications of microdevice-based aptasensors on several platforms. Highly sensitive detection techniques such as electrochemical and optical detection have been integrated into lab-on-a-chip devices and researchers have moved towards the goal of establishing point-of-care diagnoses for target analyses.

In urban areas like Chicago, daily life extends above ground level due to prevalence of high-rise buildings where residents and commuters live and work. This study examines the variation in fine particulate matter (PM2.5) concentrations across building stories. PM2.5 levels were measured using PurpleAir sensors, installed between April 8 and May 7, 2023, on floors one, four, six, and nine of an office building in Chicago. Additionally, data were collected from a public outdoor PurpleAir sensor on the fourteenth floor of a condominium located 800 meters away. Results show that outdoor PM2.5 concentrations peak at 14 meters height, then decline by 0.11 μg/m3 per meter elevation, especially noticeable from midnight to 8 AM under stable atmospheric conditions. Indoor PM2.5 concentrations increase steadily by 0.02 μg/m3 per meter elevation, particularly during peak work hours, likely caused by greater infiltration rates at higher floors. Both outdoor and indoor concentrations peak around noon. We find that indoor and outdoor PM2.5 are positively correlated, with indoor levels consistently remaining lower than outside levels. These findings align with previous research suggesting decreasing outdoor air pollution concentrations with increasing height. The study informs decision-making by community members and policymakers regarding air pollution exposure in urban settings.

A microwave-photonics method has been developed for measuring distributed acoustic signals. This method uses microwave-modulated low coherence light as a probe to interrogate distributed in-fiber interferometers, which are used to measure acoustic-induced strain. By sweeping the microwave frequency at a constant rate, the acoustic signals are encoded into the complex microwave spectrum. The microwave spectrum is transformed into the joint time-frequency domain and further processed to obtain the distributed acoustic signals. The method is first evaluated using an intrinsic Fabry Perot interferometer (IFPI). Acoustic signals of frequency up to 15.6 kHz were detected. The method was further demonstrated using an array of in-fiber weak reflectors and an external Michelson interferometer. Two piezo-ceramic cylinders (PCCs) driven at frequencies of 1700 Hz and 3430 Hz were used as acoustic sources. The experiment results show that the sensing system can locate multiple acoustic sources. The system resolves 20 nε when the spatial resolution is 5 cm. The recovered acoustic signals match the excitation signals in frequency, amplitude, and phase, indicating an excellent potential for distributed acoustic sensing (DAS).

Applications for Wireless Sensor Networks (WSNs) range from monitoring the environment to automating factories. However, sustained and effective functioning is made more difficult by Sensor Nodes (SNs) limited energy supplies in which optimization is the main issue. So with the aim of increasing the lifespan by decreasing the energy consumption of WSN, Low-Energy Adaptive Clustering Hierarchy (LEACH) protocol with Deep Learning (DL) algorithm is analyzed in this paper. LEACH is a hierarchical mechanism that elects Cluster Heads (CHs) and regularly rotates their positions in order to allocate energy use effectively by using the same amount of energy. However, Deep Learning (DL) method is used to further improve energy optimization. In many applications, the types of Deep Learning methods like Artificial Neural Networks (ANNs) have shown to be very useful. Using this method, WSNs may make more efficient decisions that reduce energy consumption. Data aggregation, duty cycling, and transmission protocols may all be optimized by Deep Learning model's ability to recognize patterns and forecast network behavior. This results in lower energy consumption, a longer lifespan for the network, and better overall performance.

In this paper we report on the use of an in-house developed solid-state hybrid microwave and radiofrequency generator operating at frequencies of 2.45 GHz and/or 480 kHz for cancer ablation in various tissues. The generator has demonstrated increased accuracy due to its custom-designed hardware, which incorporates the latest technologies and algorithms to control the emitted power versus temperature profile of the treated sample. In particular, the hybrid generator incorporates control systems based on impedance or reflected power measurements that allow controlled ablation without causing unwanted carbonisation and without including areas where tissue damage is not desired. Tests performed ex-vivo on chicken breast and bovine liver show that radiofrequency ablation (RFA) is very effective for performing controlled ablations with minimally invasive probes, such as cardiac pathologies, small lesions, tissues with particular composition, while microwave ablation (MWA) is optimal for performing large ablations in highly vascularised tissues, such as liver cancer, where it is necessary to achieve higher temperatures.

This study aims to exploit the distinctive properties of carbon nanotube materials, which are particularly pronounced at the microscopic scale, by deploying fabrication techniques that allow their features to be observed macroscopically. Specifically, we aim to create a semiconductor device that exhibits flexibility and the ability to modulate its electromagnetic wave absorption frequency by means of biasing. Initially, we fabricate a sheet of carbon nanotubes through a vacuum filtration process. Subsequently, phosphorus and boron elements are separately doped into the nanotube sheet, enabling it to embody the characteristics of a PN diode. Measurements indicate that, in addition to the fundamental diode's current-voltage relationship, the device also demonstrates intriguing transmission properties under the TEM mode of electromagnetic waves. It exhibits a frequency shift of approximately 2.3125 GHz for each volt of bias change. The final result is a lightweight and flexible carbon-based semiconductor microwave filter, which can conform to curved surfaces. This feat underscores the potential of such materials for innovative and effective electromagnetic wave manipulation.

Microwave transversal filters, which are implemented based on the transversal filter structure in digital signal processing, offer a high reconfigurability for achieving a variety of signal processing functions without changing hardware. When implemented using microwave photonic (MWP) technologies, also known as MWP transversal filters, they provide competitive advantages over their electrical counterparts, such as low loss, large operation bandwidth, and strong immunity to electromagnetic interference. Recent advances in high-performance optical microcombs provide compact and powerful multi-wavelength sources for MWP transversal filters that require a larger number of wavelength channels to achieve high performance, allowing for the demonstration of a diverse range of filter functions with improved performance and new features. Here, we present a comprehensive performance analysis for microcomb-based MWP spectral filters based on the transversal filter approach. First, we investigate the theoretical limitations in the filter spectral response induced by finite tap numbers. Next, we analyze the distortions in the filter spectral response resulting from experimental error sources. Finally, we assess the influence of input signal’s bandwidth on the filtering errors. These results provide a valuable guide for the design and optimization of microcomb-based MWP transversal filters for a variety of applications.

In this paper, the preparation methods of porous silicon nitride materials with controllable dielectric constant and pore structure were systematically studied. By using microwave sintering technology, porous silicon nitride materials with high closed pore ratio were prepared by adjusting the content of sintering additives and sintering process parameters, and controlling the grain boundary phase and pore structure and size. The effects of sintering conditions on the total porosity, closed porosity, pore structure and dielectric properties of materials were systematically studied.

Electrochemical sensors have been used for many decades. Yet, modeling of such sensors used in electrolysis mode is poorly documented, especially in the case parallel action of multiple gases. Those ones are of great interest since they constitute the first brick to bring information on natures and concentrations of a gaseous mixture composition thanks to grey box modeling of sensors array for example. Based on Butler Volmer’s equations, a model assuming parallel reactions at gold cathode has been introduced in this article and confronted to experimental results. Establishment of the model is based on the extraction of 3 variables: the charge transfer coefficient “α”, the reaction order γ, and the reaction constant rate k0. Tests performed without pollutants and with different concentrations of oxygen could be nicely fitted by the model. Then, the influence of polarization current on the 3 variables of the model has been evaluated showing a clear influence on the constant rate and the reaction order. Also, increasing the polarization current enabled us to get selectivity to oxidant gases. Similarly, the effect of the oxygen concentration was evaluated. Results showed that, in this case, the charge transfer coefficients “α” obtained for oxidant gases is quite different that the ones obtained in the polarization current varying conditions. Therefore, the model will be interesting in situations where polarization current and oxygen content are not varied together. Variation of polarization current can be quite interesting to get increased information for multivariate analysis purpose in constant oxygen content situations. Besides, other parameters have are required for applications in which the oxygen content is bound to change like exhaust gases or combustion.

This study investigates novel ferrocene-based electrochemical sensors for metal cation detection through the design, synthesis and characterisation of ferrocene derivatives. Specifically, the re-search determines the redox potentials of ferrocene versus decamethylferrocene to provide in-sight into the redox potential variations between them. The investigation also examines how electrochemical oxidation of the ferrocene moiety can modulate host affinity for transition metals cations via effects such as electrostatic interactions and changes to coordination chemistry. Metal ion coordination to receptors containing functional groups like imine and quinoline is explored to elucidate selectivity mechanisms. These findings advance the fundamental understanding of ferrocene electrochemistry and host-guest interactions, supporting the development of improved cation sensors with optimised recognition properties, sensitivity, and selectivity. Overall, the work lays the necessary groundwork for applications in analytical chemistry and sensor technologies through customised ferrocene-derived materials.

Light-addressable potentiometric sensor (LAPS) is an electrochemical sensor based on the field-effect principle of semiconductor. It is able to sense the change of Nernst potential on the sensor surface, and the measuring area can be controlled by the illumination. Due to the unique light-addressable ability of LAPS, the chemical imaging system constructed with LAPS can realize the two-dimensional image distribution detection of chemical/biomass. In this paper, the advantages of LAPS as sensing unit of microelectrochemical analysis system are summarized. Then, the greatest development of LAPS analysis system is explained and discussed. Especially, this paper focused on the research of ion diffusion, enzymatic reaction, microbial metabolism and droplet microfluidics by using LAPS analysis system. Finally, the development trends and prospects of LAPS analysis system are illustrated.

Current smartphones incorporate different types of sensors that allow us to know our spatial position, they give us information about pressure, speed, acceleration, time, acoustic level, and other different physical magnitudes. These smartphones measure each component of the magnetic field, bearing in mind that any current perpendicular to a magnetic field produces a small potential difference, transversal to the said current, being this voltage easily measurable by Hall sensors. With the implementation of three Hall sensors, and an appropriate app, we can measure the three components of the magnetic field vector, and with this we can obtain information and deduce properties of the physical systems considered. In this paper we are exploring the use of smartphones in a physics laboratory for freshman students. To do this, we have measured, using Hall sensors, the magnetic field created by a linear quadrature, and we have obtained, first of all, its dependence on the distance between the quadrupole and the magnetic sensor. The second purpose of this work is to show that the laboratory is a powerful tool that increases the significant learning of freshman students through advanced technological tools.

Flow sensing in hostile environment is of increasing interest for applications in automotive, aerospace, and chemical and resource industries. Compared to their counterparts, thermal flow sensors are attractive candidates due to the ease of fabrication, lack of moving parts and higher sensitivity. Recently, a number of thermal flow sensor prototypes have been reported in the literature demonstrating the measurement of fluid flows under hostile conditions. This paper summarizes the concept of thermal flow sensing, operational modes and transduction mechanisms. Then, the choice of materials and their corresponding properties are presented in details. The paper also reports recent progress in the development of thermal flow sensors for harsh environment. In addition, the issues and considerations in packaging are reviewed. Finally, we conclude the review with the future prospects.

A closed form solution for the common and differential modal currents induced on a pair of infinitely long parallel conductors by a voltage source was derived. For lossy conductors the current consists of a continuous spectrum of radiation modes and (for the common mode) a modified low loss Sommerfeld-Goubau mode and (for the differential mode) a quasi-TEM mode. This model is used to investigate the influence of a parallel conductor on microwave power line communication systems. For typical parameters, it is shown that the performance of these systems can be enhanced.

This work communicates cavity ring-down spectroscopy (CRDS) of methylidyne (CH) in a chemiluminescent plasma that is produced in a microwave cavity. Of interest are the rotational lines of the 0-0 vibrational transition for the A-X band and the 1-0 vibrational transition for the B-X band. The reported investigations originate from CH-radical research in 1996 that constituted the first case of applying CRDS to the CH radical. The report also includes recent analysis that shows excellent agreement of measured and computed data, and it communicates CH line strength data.

Cannabis is a flowering plant that has long been used for medicinal, therapeutic, and recreational purposes. Cannabis contains more than 500 different compounds, including a unique class of terpeno-phenolic compounds known as cannabinoids; Δ9-tetrahydrocannabinol (THC) and cannabidiol (CBD) are the most prevalent cannabinoids and have been associated with the therapeutic and medicinal properties of the cannabis plant. In this paper, continuous flow microwave assisted extraction (MAE) is presented and compared with other methods for commercial cannabis extraction. The practical issues of each extraction method are discussed. The main advantages of MAE are: continuous-flow method which allows for higher volumes of biomass to be processed in less time than existing extraction methods, improved extraction efficiency leading to increased final product yields, improved extract consistency and quality because the process does not require stopping and restarting material flows, and ease of scale-up to industrial scale without the use of pressurised batch vessels. Moreover, due to the flexibility of changing the operation conditions, MAE eliminates additional steps required in most extraction methods, such as biomass decarboxylation, winterisation, which typically adds at least a half day to the extraction process. Another factor that sets MAE apart is the ability to achieve high extraction efficiency even at the industrial scale. Whereas the typical recovery of active compounds using supercritical CO¬2 remains around 70-80%, via MAE up to 95% of the active compounds from cannabis biomass can be recovered at the industrial scale.

This study aimed to evaluate the effect of convective and microwave drying on the content of bioactive compounds of blackberry (Rubus fruticosus), drying parameters and energy consumption. The fruit was dehydrated in a convective dehydrator at a temperature of 50 °C and 70 °C and a microwave oven at power levels of 90 V, 180 V and 240 V. The highest amount of anthocyanins, polyphenols and antioxidant capacity were obtained in microwave dried blackberry fruits at 90 V and 180 V. It turned out that microwave dehydration shortened the processing time and lower the energy consumption compared to the convective drying. Blackberry fruits dehydrated at 240 V showed the shortest dehydration time, minimal energy consumption and the most efficient diffusion.

Due to Motor Neurone Diseases, a large population remains disabled worldwide, negatively impacting their independence and quality of life. This typically involves a weakness in the hand and forearm muscles, making it difficult to perform fine motor tasks such as writing, buttoning a shirt, or gripping objects. This project presents a vision-enabled rehabilitation hand exoskeleton to assist disabled persons in their hand movements. The design goal was to create an accessible tool to help with a simple interface requiring no training. This prototype is built on a commercially available glove where a camera and embedded processor were integrated to help open and close the hand, using air pressure, thus grabbing an object. An accelerometer is also implemented to detect the characteristic hand gesture to release the object when desired. This passive vision-based control differs from active EMG-based designs as it does not require individualized training. Continuing the research will reduce the cost, weight, and power consumption to facilitate mass implementation.

Drones are being used more and more frequently and in various ways to attack people and critical infrastructures, which increases their level of danger and makes early detection and risk assessment even more difficult. There is no ultimate drone sensor. Rather, drones can only be effectively detected, if suitable sensor technologies are integrated within a system. Among the best suited sensorics for this purpose are radar and optical sensors, because the advantage of the radar, given by the long detection range, can be well combined with the additional visual-based information gained from a camera in the mid- and short-range, where usually the radar fails detecting micro drones. In this paper, a modular drone detection and assistance system MODEAS is presented, which can be used to automatically detect and track drones within a range up to some kilometers on the sky, but also in complex urban environments, where buildings and vegetation offer a perfect background for camouflage. The system provides an early detection of flying objects as potential drones, when those are not at all or only as small dots visible for the human eye. Main strengths of the system are the robust AI detection to differentiate such an object against clutter (birds, clouds) and its further classification by model and payload recognition, the latter aspect being considered as an indication of dangerousness. Moreover, once a drone is detected, the system follows it automatically, precisely and smoothly with a high-resolution pan-tilt-camera, measuring the distance to the sensor station with a laser rangefinder, compute the geocoordinates and visualize them live on a map. To improve the precision of the detection, a multisensorial fusion of all sensor detections is performed. Furthermore, alarms may be generated when a drone enters a restricted area.

In recent years, the integration of sensors in agriculture has emerged as a pivotal catalyst for transforming conventional farming practices into precision agriculture. Sensor application is impacting the everyday objects that enhance human life. In this special issue, the main objective was to address recent advantages of sensor application in agriculture covering a wide range of topics in this field. This provides overview of diverse application of sensors in agriculture, highlighting their role in enhancing productivity, sustainability, and resource management. sensors are instrumental in monitoring various agriculture parameter such as soil condition, weather, crop health and livestock wellbeing. By collecting real-time data and providing valuable insight, sensors enable precision farming, optimize resource allocation, and minimize environmental impacts. we have to explore the key sensor types used in agriculture, their applications, benefits, and future prospects, emphasizing their crucial roles in the modernization of agriculture and global quest for food security and crop production.

Sign language recognition is essential in hearing-impaired people’s communication. Sign language recognition is an important concern in computer vision and has been developed with rapid progress in image recognition technology. However, sign language recognition using a general monocular camera has problems with occlusion and recognition accuracy in sign language recognition. In this research, we aim to improve accuracy by using a 2-axis bending sensor as an aid in addition to image recognition. We aim to achieve higher recognition accuracy by acquiring hand keypoint information of sign language actions captured by a monocular RGB camera and adding sensor assist. To improve sign language recognition, we need to propose new AI models. In addition, the amount of dataset is small because it uses the original data set of our laboratory. To learn using sensor data and image data, we used MediaPipe, CNN, and BiLSTM to perform sign language recognition. MediaPipe is a method for estimating the skeleton of the hand and face provided by Google. In addition, CNN is a method that can learn spatial information, and BiLSTM can learn time series data. Combining the CNN and BiLSTM methods yields higher recognition accuracy. We will use these techniques to learn hand skeletal information and sensor data. Additionally, the 2-axis Bending sensor glove data support training AI model. Using these methods, we aim to improve the recognition accuracy of sign language recognition by combining sensor data and hand skeleton data. Our method performed better than using skeletal information, achieving 96.5% accuracy in Top-1.

Polycyclic aromatic hydrocarbons (PAHs) have emerged as promising materials for organic electronics, including organic photovoltaics (OPVs), organic field-effect transistors (OFETs), and organic light-emitting diodes (OLEDs). Particularly, non-hexagonal ring-fused PAHs are highly desirable due to their unique optoelectronic properties. Herein, a new redox-active azulene-perylene diimide triad 1 and its ring-fused counterpart, diazulenocoronene diimide 2, were synthesized and fully characterized by a combination of NMR, cyclic voltammetry, spectroelectrochemistry, and UV-visible absorption spectroscopy. Density functional theory (DFT) and time-dependent DFT (TD-DFT) calculations were performed to gain further insight into various electronic transitions. Interestingly, we found that the adaptive response to acids and bases manifests itself in a reversible two-color-change that can be attributed to changes in the chemical structures.

Novel tetragonal matrix Ba0.5Gd0.5-xNaxF2.5-x, where x = 0.05, doped by Yb3+, Ho3+, Er3+, was synthesized by molten salt synthesis (MSS) from nitrate flux. XRD data show that tetragonal phase with a = 4.122(1) Å, c = 17.672(1) Å is stable in argon atmosphere up to 960 °C. Luminescence spectra recorded in 500-900 nm and 1050-1700 nm upon 974 nm pumping demonstrated the characteristic luminescence at 1550 nm (4I13/2 → 4I15/2) for Er3+ and 1150 nm (5I6 → 5I8) for Ho3+. The relative thermal sensitivity (Sr) at 296-316 K were 0.3 %*K-1 and 5.5%*К-1 in shortwave infrared (SWIR) and visible range, respectively. Synthesized luminophores can be used as dual-range optical temperature sensors, which simultaneously operating in visible and SWIR ranges.

Sensing Technology (ST) plays a key role in Structural Health Monitoring (SHM) systems. ST focuses on developing sensors, sensory systems or smart materials that monitor a wide variety of materials properties aiming to create smart structures and smart materials, using Embedded Sensors (ESs), and allowing continuous and permanent measurements of the structural integrity. The integration of ESs is limited to the processing technology to embed the sensor due to its high-temperature sensitivity and the possibility of damage during its insertion into the structure. In addition, the technological process selection is dependent on the base material composition, either metallic or composite parts. The selection of smart sensors or the technology underlying them is fundamental to the monitoring mode. This paper presents a critical review of the fundaments and applications of sensing technologies for SHM employing ESs, focusing on the actual developments and innovation of these, as well as analysing the challenges that these technologies present, to build a path that allows a connected world through distributed measurement systems.

: This paper presents a couple of meal monitoring systems for senile dementia patients by using electronic weight and temperature sensors. These monitoring systems enable to convey the information of the amount of meal taken by the patients in real-time via wireless communication networks onto the mobile phones of their families or nurses in charge. Thereby, the nurses can easily spot the most desperate patient to take care of while the families can have relief to see the crucial information for survival of their parents at least three times a day. Meanwhile, the senile dementia patients tend to suffer the burn of their tongues because they can hardly recognize the temperature of hot meals served and therefore avoid the burn of tongues. This phenomenon can be discarded by utilizing the meal temperature monitoring system which displays alarm to the patients when the meal temperature is above the reference. These meal monitoring systems can be easily implemented by utilizing low-cost sensor chips and Arduino UNO boards so that elder-care hospitals and nursing homes can afford to exploit them with no additional cost. Hence, we believe that the proposed monitoring systems would be a potential solution to provide a great help and relief not only for the professional nursing nurses working in elder-care hospitals and nursing homes, but also for the families of the dementia patients.

The protection of electronics against environmental influences and mechanical loads is important for integration of conventional electronics in textile conductive tapes. For this purpose, the sensors on the tapes are molded with plastic locally. This process step is recognized in the injection molding process. The molding compound is then later selected depending on: The field of application, the parameters of the manufacturing process and the textile tape properties. We have designed a mould for liquid silicone (LSR) as well as for the textile and electronic insertions. The cavities are sealed by a local compression of the textile and the two inserts are positioned with position pins representing the main aspect of the mould design. The sampling tool and the process parameter optimization are mainly based on the material properties of the silicone and the mechanical sensitivity of the inserts. To reduce the deformation of the circuit boards by the melt front and ensuring the functionality of the electronics a low-pressure process is used.

In this paper, the effects on the rheological properties, particle size distribution, and fluorescence properties of red wine were investigated under microwave irradiation, and the mechanism of the effects of microwave irradiation on the sensory properties of red wine was discussed. The results showed that the effect of microwave on the rheological properties in red wine could be fitted by the Power-law model and Carson model, through the analysis of the rheological constants, yield stress, and viscosity coefficient of wine, it was found that microwave treatment could improve leg phenomenon and thickening effect by the change of rheological properties; the particle size distribution in wine indicated that microwave irradiation did change the particle size distribution through friction effect and oxidative polymerization, resulting in the wine’s visual effect and mouthfeel; the wine quality could be improved by enhancing the fluorescence intensity under different microwave conditions, which meant that microwave technology could speed up the formation of fluorescent substances, such as the polymerization of flavan-3-ols. In conclusion, microwave treatment could modify the sensory characteristics of wine, and further provide the theoretical basis for the application of microwave in winemaking.

Abstract Background and Objective: Medical Microwave Radiometry (MWR) is used to capture the thermal properties of internal tissues and has usages in breast cancer detection. Our goal in this paper is to improve classification performance and investigate automated neural architecture search methods. Methods: We investigate optimizing the weights of a weight agnostic neural network using bi-population covariance matrix adaptation evolution strategy (BIPOP-CMA-ES) once the topology is found. We compare it against a weight agnostic and cascade correlation neural network. Results: The experiments are conducted on a breast cancer dataset of 4912 patients. Our proposed weight agnostic BIPOP-CMA-ES model achieved the best performance. It obtained an F1-score of 0.9225, accuracy of 0.9219, precision of 0.9228, recall of 0.9217 and topology of 153 connections. Conclusions: The results are an indication of the potential of MWR utilizing a neural network-based diagnostic tool for cancer detection. By separating the tasks of topology search and weight training, we are able to improve the overall performance.

To reduce the carbon emissions during heating in the manufacturing process, microwaves have attracted significant attention. Microwave has a lot of advantages rather than traditional heating method such as rapid heating, lower thermal damage and eco-friendly process. In order to apply microwaves to manufacturing process, uniform and efficient heating is required. We have analyzed the effect of various design parameters such as cavity heights, the application of the reflector, and the number and positions of waveguides for uniform and efficient heating by numerical simulation and verified that by experiment. The results showed that a slight change in the cavity height altered the electromagnetic field distribution and heating parameters, such as the coefficient of variance and power absorption efficiency. With reflectors installed, uniform heating was achieved and power absorption was improved, with the spherical reflector showing the maximum efficiency. The use of double waveguides heated the target material in a uniform manner. An increase in the power supply also led to uniform heating. This large-scale analysis will be helpful in applying microwaves to actual industrial sites.

We review recent work on broadband RF channelizers based on integrated optical frequency Kerr micro-combs combined with passive micro-ring resonator filters, with microcombs having channel spacings of 200GHz and 49GHz. This approach to realizing RF channelizers offers reduced complexity, size, and potential cost for a wide range of applications to microwave signal detection.

The integral extraction via microwave-assisted hydrodiffusion and hydrodistillation of water-soluble bioproducts contained in the peel of Opuntia ficus-indica white and red cultivars harvested in Sicily, affords red and stable aqueous extracts mostly containing valued betanin, pectin and biophenols. Potentially useful as nutraceutical products, these aqueous extracts are a source of valued ingredients in high demand for a number of important food, cosmetic, beverage and nutraceutical applications.

Current generation witnesses a huge interest in optical waveguide due to their salient feature such as low cost, immune to electromagnetic interference, easy to multiplex, compact size, etc. These features of the optical fibers makes it an useful tool for various sensing applications including medicine, automotive, biotechnology, food quality control, aerospace, physical and chemical monitoring etc. Among all the reported application, the device has been widely exploited to measure the physical and chemical variation in surrounding environment. Optical fiber based temperature sensor plays a crucial role in this decade to detect high fever and tackle COVID like pandemic. Recognizing the major developments in the field of the optical fibers, this article aims to provide recent progress in temperature sensor utilizing several sensing configuration including standard fiber, photonic crystal fiber, and Bragg grating fibers. Additionally, the article also highlights the advantages, limitations, and future possibilities in this area.

It is since long known, that SAW devices, resonators as well as delay lines, can be used as passive wireless sensors for physical quantities like temperature and pressure as well as gas sensors or ID-Tags. The sensors are robust, work passively without battery, can be applied at high temperatures and provide a high resolution. Nevertheless, if the devices should be readout wirelessly in an industrial environment, several constraints have to be taken into account, especially when more than one quantity or device needs to be measured at the same time. The paper addresses the challenges that have to be tackled when establishing multi-sensor-wireless-readout for industrial applications. Major issues here are the legal ISM-band regulations, as well as sampling time and costs, which impose severe restrictions to any system design. We describe several design approaches and their constraints. We have successfully designed sensors based on reflective delay lines that allow the parallel readout of four independent temperature sensors in the 2.45 GHz ISM-band. These devices have been fabricated, positively tested and demonstrate the applicability of SAW sensors for industrial applications.

Carbon nanotubes have been attracting considerable interest among material scientists, physicists, chemists and engineers for almost 30 years. Owing to their high aspect ratio, coupled with remarkable mechanical, electronic and thermal properties, carbon nanotubes have found application in diverse fields. In this review, we will cover the work on carbon nanotubes used for sensing applications. In particular, we will see examples where carbon nanotubes act as main players in devices sensing biomolecules, gas, light or pressure changes. Furthermore, we will discuss how to improve the performance of carbon nanotube-based sensors after proper modification.

In this work we present a versatile, rapid, and low-cost manufacturing technique to develop bioceramic scaffolds that could enhance bone tissue regeneration via microwave preparation using a commercial microwave oven. The scaffolds were prepared combining hydroxyapatite and water glass (sodium trisilicate solution), foamed by using a microwaves oven and then characterized by means of SEM-EDS, mechanical properties, infrared spectroscopy (ATR-FTIR), density and stability test in water. Furthermore, in vitro tests were performed to verify the affinity of osteoclast cells versus the so prepared scaffold. The morphology of the samples showed interconnected pores suitable for promoting tissue regeneration and vascularization while specific mechanical properties were preserved. The physicochemical characterization and the in vitro tests presented promising results for bone regenerative applications.

With the rapid development of electronic and communication technology in military radar, the demand for microwave absorbing materials in low-frequency with thin layer is growing increasingly. In this study, flexible Co3O4/CC (carbon cloth) composites derives from Co-MOFs (metal-organic frameworks)/CC are prepared by hydrothermal and thermal treatment processes. The flexible precursors of Co-MOFs/CC are calcined with different calcination temperatures, which the material structure, dielectric properties and microwave absorption performance are changed. With the increase of calcination temperature, the minimum reflection loss of the corresponding Co3O4/CC composites gradually moves to the lower frequency with thinner thickness. In addition, the Co3O4/CC composites with 25 wt% filler loading ratio exhibit the minimum reflection loss (RL) of -46.59 dB at 6.24 GHz with 4.2 mm thickness. When the thickness is 3.70 mm, the effective absorption bandwidth is 3.04 GHz from 5.84 to 8.88 GHz. This study not only proves that the composite Co3O4/CC is a kind of outstanding microwave absorbing material with better flexibility, but also provides a useful inspiration for the low frequency and broadband microwave absorbing material.

Microwave photonic (MWP) transversal signal processors offer a compelling solution for realizing versatile high-speed information processing by combining the advantages of reconfigurable electrical digital signal processing and high-bandwidth photonic processing. With the capability of generating a number of discrete wavelengths from micro-scale resonators, optical microcombs are powerful multi-wavelength sources for implementing MWP transversal signal processors with significantly reduced size, power consumption, and complexity. By using microcomb-based MWP transversal signal processors, a diverse range of signal processing functions have been demonstrated recently. In this paper, we provide a detailed analysis for the processing inaccuracy that are induced by the imperfect response of experimental components. First, we investigate the errors arising from different sources including imperfections in the microcombs, the chirp of electro-optic modulators, chromatic dispersion of the dispersive module, shaping errors of the optical spectral shapers, and noise of the photodetector. Next, we provide a global picture quantifying the impact of different error sources on the overall system performance. Finally, we introduce feedback control to compensate the errors caused by experimental imperfections and achieve significantly improved accuracy. These results provide a guide for optimizing the accuracy of microcomb-based MWP transversal signal processors.

Methylsilsesquioxane aerogels with uniform mesopores have been facilely prepared via a sol–gel process followed by microwave drying with methyltrimethoxysilane (MTMS) as precursor, hydrochloric acid (HCl) as catalyst, water and methanol as solvents, hexadecyltrimethylammonium chloride (CTAC) as surfactant and template and propylene oxide (PO) as gelation agent. The microstructure, chemical composition and pore structures of the resultant MSQ aerogels were investigated in detail to achieve controllable preparation of MSQ aerogels, and the thermal stability of MSQ aerogels was also analyzed. The gelation agent, catalyst, solvent and microwave power have important roles on pore structures of MSQ aerogels. Meanwhile, microwave drying method is found to not only have a remarkable effect on improving production efficiency, but also be conducive to avoid the collapse of pore structure especially micropores during drying. The resulting MSQ aerogel microwave-dried at 500 W possesses a specific surface area up to 821 m2/g and a mesopore size of 20 nm, and displays good thermal stability.

The fourth industrial revolution, also known as Industry 4.0, has led to an increased transition towards automation and reliance on data-driven innovations and strategies. Companies in the manufacturing sector are heavily integrating Industry 4.0 technologies, including cloud compu-ting, cyber-physical systems (CPS), big data analytics, horizontal and vertical system integration, the internet of things (IoT), and additive manufacturing (3d printing). The interconnected systems and processes have significantly increased operational efficiency, enhanced organizational capacity to monitor and control functions, reduced costs, and improved product quality. One significant way that companies have achieved these benefits is by integrating diverse sensor technologies within these innovations, allowing critical data collection on products, equipment performance, and maintenance. The sensors connect systems and machines, allowing them to communicate and track operations for enhanced operations. While numerous research has been conducted to show the role of sensors in industry 4.0, limited studies show how these innovations can leverage product design to maximize benefits and opportunities. Given the rapidly changing market conditions, Industry 4.0 requires new products and business models to ensure companies adjust to the current and future changes. These requirements call for the evolutions in product design processes to accommodate design features and principles applicable in the current dynamic business environment. This research paper employs a systematic bibliometric literature review (LRSB) methodology to explore and synthesize data on how Industry 4.0 and sensors can leverage product design. The results show that various product design features create opportunities to be leveraged to guarantee the success of Industry 4.0 and sensor technologies. However, the research also identifies numerous challenges that undermine the ongoing transition towards intelligent factories and products.

Today, there are commercially available high-performance electric wheelchairs, capa-ble of responding to strong limitations. However, despite these advancements, there is a significant portion of the population with severe disabilities who cannot access this mobility solution due to safety reasons. Indeed, either due to motor issues preventing reliable control of the wheelchair's commands, or associated visual or cognitive pathologies, the use of an electric wheelchair by these individuals would put them at risk and could also constitute a danger to those around them. This is why our research team is working on the development of augmented wheelchairs that allow a greater autonomy. We are mainly developing a system compatible with all electric wheel-chairs on the market, capable of making them anti-collision and anti-fall on uneven ground (sidewalks, stairs, etc.). In this article, we present our solution regarding the anti-collision function, in particular the sensors used to do this, as well as the strategy. We will focus on the shortcomings and weaknesses of various types of sensors and demonstrate how, by combining them in a certain way, we can develop a collision avoidance device capable of managing the diversity of everyday life situations. The two types of sensors that will be combined here are an in-house developed special near infrared sensor from the laboratory and a commercially available ultrasonic sensor. We will present the internal operation of the sensors, their limitations, experimental tests involving integration with the wheelchair, and the structure of the complete device.

This paper provides a data set collected with an underground shaft mobile mapping system equipped with rotated Velodyne VLP-16, Velodyne Ultra Puck VLP-32c, Livox Tele-15, and IMU Xsens MTi-30. The ground truth data was acquired with a geodetic survey including 15 ground control points and 6 Faro Focus 3D Terrestrial Laser Scanner stations of a total 273,784,932 of 3D measurement points. The aim of the paper is to describe the data set of a mining shaft. Obtained mobile mapping data can be the basis for detailed analyzes of the technical condition of the shaft. This data set provides an end-user case study of realistic applications in mobile mapping technology. It provides ground truth data, mobile mapping data and software tools for manipulation and visualization. The project is released and maintained at https://michalpelka.github.io/mine-mapping-dataset/.

Vehicle safety promises to be one of the Advanced Driver Assistance System (ADAS) biggest benefits. Higher levels of automation remove the human driver from the chain of events that can lead to a crash. Sensors play an influential role in vehicle driving as well as in ADAS by helping the driver to watch the vehicle’s surroundings for safe driving. Thus, the driving load is drastically reduced from steering as well as accelerating and braking for long-term driving. The baseline for the development of future intelligent vehicles relies even more on the fusion of data from surrounding sensors such as Camera, Lidar and Radar. These sensors not only need to perceive in clear weather but also need to detect accurately adverse weather and illumination conditions. Otherwise, a small error could have an incalculable impact on ADAS. As most of the current study is based on indoor or static testing. In order to solve this problem, this paper designs a series of dynamic test cases with the help of outdoor rain and intelligent lightning simulation facilities to make the sensor application scenarios more realistic. As a result, the effect of rainfall and illumination on sensor perception performance is investigated. As speculated, the performance of all automotive sensors is degraded by adverse environmental factors, but their behaviour is not identical. Future work on sensor model development and sensor information fusion should therefore take this into account.

Phenology is one of the ubiquitous fingerprints of climate change on our ecosystems. Monitoring the spatiotemporal patterns of vegetation phenology is thus critical. A wide range of sensors have been used to monitor vegetation phenology. Sensor point of view and resolution can potentially impact estimates of phenology. We compared three different sensors from three different remote sensing platforms—a UAV mounted RGB camera, an under canopy, upward facing hemispherical camera with R, G and NIR capabilities, and a tower mounted RGB PhenoCam—to estimate spring phenological transition in a mixed-species temperate forest in central Virginia, USA. Our study had two objectives: 1) to compare the above- and below- canopy inference of canopy greenness (green chromatic coordinate and normalized difference vegetation index) and canopy structural attributes (leaf area and gap fraction) by matching under-canopy hemispherical photos with high spatial resolution (0.03 m) drone imagery to find the appropriate spatial coverage and resolution for comparison; 2) to compare how each sensor performed in estimating the temporality of the spring phenological transition. We find that a spatial buffer of 20 m radius for UAV imagery is most closely comparable to under-canopy imagery in this system. Sensors and platforms agree within +/- 5 days of when canopy greenness stabilizes from the spring phenophase into the growing season. This work has implications for paring UAV imagery with both tower-based observation platforms, as well as plot-based studies (e.g. long-term monitoring, existing research networks, permanent plots).

Alginate, a biopolymer promising in food, biomedical, pharmaceutical, and electronic materials industries, is characterized by its biodegradability, biocompatibility, low toxicity, and gel-forming properties. It is most abundantly found in brown algae. However, conventional dilute acid and alkali extraction methods face limitations in commercialization due to their long processing time, low throughput, and high solvent requirements. In this study, a microwave-assisted extraction (MAE) process for sodium alginate was designed to improve extraction efficiency. Solid/liquid ratio, extraction temperature, and extraction solvent concentration were major variables affecting sodium alginate extraction from Undaria pinnatifida(sea mustard). They were then statistically optimized using response surface methodology. Under optimal conditions (13.27 g/L, 91.86 ℃, 2.51 %(w/v), and 15 min), the yield was 38.41 %, which was 93.43 % of the theoretical content of sodium alginate in Undaria pinnatifida. Our work has confirmed the productivity and industrial feasibility of efficient extraction of sodium alginate from marine biomass, and we hope that it will serve as an encouraging case for the application of biopolymers as one of the desirable options for alternative petrochemicals to construct a sustainable society.

An enormous interest in the development of efficient protocols for cellulose extraction has been demonstrated in the last years, however, they were usually based on non-sustainable chemical and thermal approaches. In this work we describe a new and more sustainable method for cellulose extraction from eucalyptus and pine tree wood waste products exclusively performed using microwave-assisted radiation. The methodology includes 3 main steps: i) alkaline treatment; ii) bleaching I, using H2O2; and iii) bleaching II, an acidic treatment. Samples obtained in each step were characterized by Fourier-transform Infrared (FTIR) spectroscopy, powder X-ray diffraction (PXRD), thermogravimetric analysis (TGA) and differential scanning calorimetry (DSC). The results were compared with those of starting materials, with the commercially available microcrystalline cellulose and with an industrial paper pulp. Results confirmed that for both type of wood wastes, cellulose was retained during the extractions procedures and that the removal of hemicellulose was achieved at the last step as seen by the FTIR spectra and TGA curves. The developed protocol is innovative since it constitutes an easy and quick approach to extract cellulose, from eucalyptus and pine tree wood waste using mild chemical and thermal conditions, microwave irradiation, and environmentally friendly purification steps. This approach offers the possibility of a future scale-up study to potentially apply the develop protocol to the extraction of cellulose in an industrial scale.

Effective control of domain walls or magnetic textures in antiferromagnets promises to enable robust, fast, and non-volatile memories. The lack of net magnetic moment in antiferromagnets implies the need for creative ways to achieve such a manipulation. Here, we investigate changes in magnetic force microscopy (MFM) imaging and in magnon-related mode in Raman spectroscopy of virgin NiO films under a microwave pump. After the MFM and Raman studies, a combined action of broadband microwave (0.01-20 GHz, power scanned from −20 to 5 dBm) and magnetic field (up to 3 kOe) were applied to virgin epitaxial (111) NiO and (100) NiO films grown on (0001) Al2O3 and (100) MgO substrates, following which the MFM and Raman studies were repeated. We observed a suppression of the magnon-related Raman mode subsequent to the microwave exposure. Based on MFM imaging, this effect appears to be caused by the suppression of large antiferromagnetic domain walls due to the possible excitation of antiferromagnetic spin oscillations localized within the antiferromagnetic domain walls.

In this paper, the extraction of essential oil (EO) from thyme by consecutive use of ultrasound and microwave treatments is presented. The aim of the study was to apply an ultrasound pre-treatment of thyme leaves to enhance the thymol content and the extraction yield of the EO obtained by microwave-assisted hydro-distillation (MWHD). Compared with the conventional hydro-distillation (CHD), the consecutive use of ultrasound and microwave treatments resulted in a 72% lower extraction time. When the ultrasound pre-treatment (using the ultrasonic processor with an amplitude of 70%) was applied, the EO content was 23% higher compared to the extraction without pre-treatment. The EO samples were analyzed by GC/MS. The results showed that the major component, thymol, varied from 43.54% (by CHD) to 65.94% (by consecutive use of ultrasound and microwave treatments).

In this work, silver nanoparticles (AgNPs) were synthesized rapidly and eco-friendlily using the extract of Mulberry leaves and aqueous solution of silver nitrate without any toxic chemical [1,2]. The Mulberry leaves extract acts as both reducing agent and stabilizing agent. The UV-Vis spectrum shows peak at 430 nm. The TEM image of synthesized AgNPs sample shows spherical shaped particles whose size range from 15 to 20 nm. TEM image of nano silver solution sample synthesized by microwave assisted method shows nearly spherical particles with an average particle size of 10 nm. The absorption UV-vis spectrum of silver nanoparticles synthesized by microwave assisted method (AgNPsmw) shows a sharp absorption band around 415 nm. After two month storage of AgNPsmw, the absorption spectrum of AgNPsmw was taken again. The UV-Vis spectrum shows negligible peak changes of silver nanoparticles have occurred after two months of storage. The synthesized AgNPs material could be used as an antimicrobial, used in the field of textile and in wastewater treatment.

This paper provides a comparative study between microwave tomography and synthetic time-reversal imaging techniques as applied to ground penetrating radar (GPR) surveys. The comparison is carried out by processing experimental data collected at a controlled test site, with various types of buried targets at given subsurface depths and representative soil conditions. It is shown that the two techniques allow us to obtain complementary information about position, depth and size of the targets from a single GPR survey.

The root extracts of Symphytum officinale (comfrey) are commonly used in traditional medicine to treat muscle, joint, skin and bone disorders. However, little information is available on the biomedical functions of comfrey leaves. In this study, sequencing results of Internal Transcribed Spacer and trnL-trnF genes showed that plants purchased from the local market were comfrey and named as S. officinale WL (WL). The optimal extraction conditions of WL leave with the highest extract yield and contents of total phenols and flavonoids by microwave-assisted extraction were identified. The antioxidative and anti-inflammatory activities and possible molecular mechanism(s) of the WL leaf extract (WLE) were evaluated. Furthermore, the major component of WLE was identified as rosmarinic acid by HPLC. Results showed that the optimal extract condition was obtained with 750W microwave power, 50℃, 75% methanol, the solid-to-solvent ratio of 1:10, and 15 minutes. Results of all DPPH, ABTS and superoxide radical scavenging activities, reducing power, ferrous ion chelating activity, and ferric reducing antioxidant power showed high antioxidative capacities of WLE. Furthermore, WLE showed obvious DNA protecting activity. WLE attenuated lipopolysaccharides-stimulated inflammation by suppressing iNOS, COX-2, IL-1β, IL-6, and TNF-α expressions in RAW264.7 macrophages. These attenuations involved in inactivations of lipopolysaccharides-induced NF-κB and MAPK signaling pathways.

The occurrence of chaotic instability of oscillations at the output of a single-stage amplifier on a powerful bipolar microwave transistor when a biharmonic signal is amplified is considered. It has been established that at a high level of the input signal at the output of the amplifier, the signal contains a significant chaotic component. Cases were experimentally studied when the frequency distance between the partial frequency components of a biharmonic signal is close to the gain band and when it is much smaller than this band. It has been established that in the first case, the chaos in oscillations is associated with the emergence of a sequence of trains of a forced oscillatory process with arbitrary initial phases and durations. In the second case, the appearance of a chaotic pedestal is associated with the chaos in the passive underexcited mode of the nonlinear circuit formed by the capacitance of the p-n junction and the input matching circuits of the amplifier stage.

The development of new medical monitoring applications requires precise modeling of the human body effects as well as simulating and emulating realistic scenarios and conditions. The first aim of this paper is to develop realistic and adjustable human body 3D emulation platforms which could be used for evaluating emerging microwave-based medical monitoring/sensing applications such as the detection of brain tumors, strokes, breast cancers as well as for capsule endoscopy studies. The new phantom recipes are developed for microwave ranges for the realistic shaped phantom molds. The second aim is to validate the feasibility and reliability of the phantoms for practical scenarios with electromagnetic simulations using tissue layer models and biomedical antennas. The third aim is to investigate the impact of the water temperature in the phantom cooking phase on the dielectric properties of the stabilized phantom. The evaluations show that the dielectric properties of the developed phantoms correspond closely to those of real human tissue. The error in dielectric properties varies between 0.5-8%. In the practical scenario simulations, the differences obtained with phantoms-based simulations in S21 parameters are 0.1-13dB. However, the differences are smaller in the frequency ranges targeted for medical applications.

The microwave field is used for drying and disinfection of grain, during pre-sowing seed treat-ment. The use of a microwave field in these installations leads to an increase in their productivity and a decrease in the energy consumed by them. One of the principal problems of microwave field use for treatment of dense grain layers is to insure sufficient distribution uniformity of the field. In this article, waveguide design options have been discussed that serve to introduce microwave radiation into the grain layer. Mathematical simulation of the electromagnetic field distribution was performed with the use of CST Microwave Studio software in order to evaluate and compare horn-type, rectangular and semicircular waveguides. The data on the standing wave ratio and radiation efficiency for these types of waveguides have been reported. Specific features of the microwave electromagnetic field distribution and radiation power in the output of those wave-guides have been described. Results of mathematical simulations enabled to make out that sem-icircular waveguides with slot-type radiators are preferable for processing dense grain layers.

This paper has designed a four-channel wide dynamic microwave rectifier circuit for the shortcomings of uneven output voltage of each branch of the multi-channel rectification technology. A voltage-doubling rectifier circuit with identical structure was used in each branch. The four rectifier branches shared the same load at the output terminal, allowing the rectifier circuit to have an RF-DC conversion efficiency greater than 50% over the input power range from 12mW to 274mW, widened by 274% compared to a single channel. Not only the advantages of multi-channel technology with wide dynamics were retained, but also the output voltage was highly consistent and could be directly output in parallel without complex power electronics conversion.

Recent analyses of cosmic microwave background (CMB) maps have been interpreted as demonstrating that the Universe was born without an initial rotation. However, these analyses are based on unrealistic models and do not contain essential ingredients such as quantum effects, the strong, weak and gravitational interactions between the components, their intrinsic spins and magnetic moments, as well as primordial black holes. If the Universe was born spinning these effects would distribute the initial spin angular momentum among its components long before the CMB forms at recombination. A primordial spin would now appear as a nonzero total angular momentum of its components along the direction of the original spin, and a primordial large-scale rotation would no longer be apparent. The existence of a special axis or direction would break a fundamental symmetry assumed in general relativity, cosmic isotropy, and a net angular momentum implies a cosmic parity violation.

The paper focuses of the interaction between tungsten (W) wire and microwave field in carbon dioxide (CO2) atmosphere. Our experimental set-up uses a microwave plasma generator in order to generate the plasma from the metallic wires. The microwave plasma generator contain a cylindrical cavity - TM_011 propagation modes, commercial source (magnetron) having the 2.45 GHz frequency at 800 W microwave and power supply. In the focal point of the cylindrical cavity we have a high energy of the electromagnetic radiation. The metallic wires from this area will be vaporized and ionized having as effect CO2 dissociation. The electron temperature regarding metallic plasma produced was estimated using the ratio of atomic emission lines acquired by a high definition of the optical multichannel spectrometer. Determination of the CO2 dissociation quantity was estimated measuring of the carbon monoxide (CO) resulting of the CO2 dissociation process. We obtained a high electron temperature of the plasma and a strong dissociation of the CO2.

This paper provides an overview of flexible and wearable respiration sensors with emphasis on their significance in healthcare applications. The paper classifies these sensors based on their operating frequency distinguishing between high-frequency sensors which operate above 10 MHz and low-frequency sensors. The operating principles of breathing sensors as well as the materials and fabrication techniques employed in their design are addressed. The research highlights the need for robust and flexible materials to enable the development of reliable and comfortable sensors. Finally, the paper presents potential research directions and proposes research challenges in the field of flexible and wearable respiration sensors. Thus, identifying emerging trends and gaps in knowledge, it encourages further advancements and innovation in the rapidly evolving domain of flexible and wearable sensors.