Global climatic event on Middle Miocene triggered by geology activity is called by Mid- Miocene Climatic Optimum (MMCO). This event was widely distributed and associated with increasing temperature and CO2 content in the atmosphere. The effect of MMCO was widely known the mid-latitude region, but still limited information in low latitude sediments. This study try to perform the effect of MMCO at Cibulakan Formation in which deposited in the low latitude basin, Bogor Basin. Fifty eights samples from Cileungsi River were taken at Cibulakan Formation and quantitative nannoplankton analysis was carried out for this study. Nannoplankton shows the sensitive response with sea surface temperature changes. Increasing of total population nannoplankton indicates the rising of temperature and dropping temperature is marked by decreasing population. The effect of sea surface temperature changes relates with salinity changes as the effect of evaporation. Helicosphaera carteri and Umbilicosphaera jafari were counted to know the salinity trend at Cibulakan Formation. Sea surfaces temperature changes was observed on Early Miocene which was influenced by small scale Early Miocene glaciation and active tectonic during this period. Warming temperature taken place on Middle Miocene as the effect of warm and open sea during Mid Miocene Climatic Optimum. Afterwards, hot temperature continued on Late Miocene triggered by global increasing temperature at Pacific Ocean and widely distribution of clean water at North West Java Basin.

The Yangtze River is cross-linked with numerous lakes within its floodplain and is a worldwide biodiversity hotspot. There is no evidence indicating when this unique river-lake system developed. The endemic East Asian cyprinid clade has evolved diverse spawning adaptations to different flow conditions. Our ancestral egg-type reconstruction showed an ancestral state of adhesive eggs and later demersal eggs origination (both stream adaptations). Semi-buoyant eggs emerged ~18 Mya as a fast-flowing river adaptation, with increased hydration via three yolk protein degradation pathways, ion transport pathways and egg envelope permeability transition pores. Adhesive eggs evolved secondarily ~14 Mya with the egg envelope increasing to four layers and an adhesive layer, along with an increase in adhesiveness via microfilament/adhesive-related protein crosslinking and enhanced glycosaminoglycan biosynthesis, improving adherence to submerged lake plants, indicating that the cross-linked river-lake system formed in the mid-Miocene. This study provides a unique biological evidence for large-scale water system evolution.

Climate simulations in West Africa have been attributed with large uncertainties. Global climate projections are not consistent with changes in observations at the regional or local level of the Niger basin, making management of hydrological projects in the basin uncertain. This study evaluates the potential of using the quantile mapping bias correction to improve the Coupled Model Intercomparison Project (CMIP5) outputs for use in hydrology impact studies. Rainfall and temperature projections from 8 CMIP5 Global Climate Models (GCM) were bias corrected using the quantile mapping approach. Impacts of climate change was evaluated with bias corrected rainfall, temperature and potential evapotranspiration (PET). The IHACRES hydrological model was adapted to the Niger basin and used to simulate impacts of climate change on discharge under present and future conditions. Bias correction significantly improved the accuracy of rainfall and temperature simulations compared to observations. Nash coefficient (NSE) for monthly rainfall comparisons of 8 GCMs to the observed was improved by bias correction from 0.69 to 0.84. The standard deviations among the 8 GCM rainfall data were significantly reduced from 0.13 to 0.03. Increasing rainfall, temperature, PET and river discharge were projected for all GCMs used in this study under the RCP8.5 scenario. These results will help improving projections and contribute to the development of sustainable climate change adaptation strategies.

The paper presents attribute based characterization of nanomaterials method for computer storage and retrieval as knowledgebase. The knowledgebase permits indepth understanding and comparison between nanomaterials available with the scientists and product developers to satisfy their research and development (R & D) needs. Techniques for order preference by similarity to ideal solution (TOPSIS) is proposed to evaluate nanomaterials in the presence of multiple attributes. The method normalizes attributes to nullify the effect of different units and their values in the range of 0 to 1. The relative importance of different attributes for different applications is considered. The weight vector is derived using Eigen value formulation. The positive and negative benchmark solutions are derived. Euclidean distance of alternatives from these best and worst solution leads to the development of proximity /goodness/suitability index for ranking. Final decision is taken by decision makers by SWOT analysis and short and long term strategies of the organisation. The methodology is illustrated with the help of an example and step-by-step procedure. Results, discussion and conclusion highlights the importance and practical application.

In Mexico there is a deficit in the production of pine resin, because it depends on natural forests. Therefore, it is necessary to select provenances and phenotypes of potential species such as P. oocarpa. The objective was to determine the difference between provenances and the variation of resin components and quality, as well as the effect of geographic and climatic factors. Resin from five provenances was collected from southern Mexico. The percentage of rosin, turpentine and water was obtained, as well as the acidity and saponification index. P. oocarpa resin had 80.94 % rosin, 7.7 % turpentine and 11.49 % water. The saponification and acidity index was 125.47 and 117.49 mg KOH.g_1, respectively. All variables showed differences (p≤ 0.0001) between provenances. The provenance contributed between 6.44 and 11.71 % to the total variance, the error contributed between 88.29 and 93.56 %. Geographic and climatic variables only had an effect on the percentage of turpentine; the correlation was negative with altitude and longitude, but positive with temperature and precipitation. The results allow defining seed collection sites for resin plantations and orienting the selection for a P. oocarpa improvement program.

Most of the mid-high permeability sandstone oilfields in China have entered the ultra-high water cut stage, accompanied with the highly-dispersed residual oil, and the control effect of mi-cro-heterogeneity on the residual oil is increasingly prominent. Understanding the microscopic characteristics of pore structural and its evolution during the long-term waterflooding is critical for enhancing the accuracy and efficiency of oil field exploitation. While the previous insights paid more attention to the geometrical and morphological features of pore structure and ignores the relation of pore structure with the fluid flow capacity. In this study, we propose a microscopic pore structure classification method considering pore size and local permeable capacity, which realizes the physical classification and quantitative evaluation of pore structure characteristics for different permeability rocks. The micro-pore structure is classified into 6 types based on the key evaluation parameters of pore diameter and flow flux area. By taking six mid-high permea-bility sandstone core samples from Daqing oilfield in China, a series of long-term waterflooding experiments are carried out and the interior pore structure was captured using high precision CT scanning technique. The results reveals that high-permeability reservoirs exhibit concentrated pores diameters and finer throats, whereas mid-permeability reservoirs exhibit smaller pores and throats in greater quantity. With the increase of water injection volumes, the permeable ca-pacity and connectivity of the high-connectivity pore space in ultra-high- and high-permeability reservoirs are enhanced, and in mid-permeability reservoirs, the micro-heterogeneity intensifies the increase in low-connectivity small pores. These findings provide new insights for the micro-scopic heterogeneity and a solid theoretical basis for investigating the occurrence of microscopic residual oil and optimising enhanced oil recovery strategies at the late stage of ultra-high water cut.

Single-phase-to-ground fault in non-effectively grounded systems poses serious public safety concern. Along with increasing deployment of low-voltage (LV) sensors, new opportunities and ways are created for solving this traditional problem in distribution systems. A new approach, identifying primary single-phase-to-ground line fault and locating it through measurement data from smart sensors deployed in the secondary side of distribution transformers, is proposed in this paper. When a fault occurs in primary distribution feeder, the transient aerial mode voltage (AMV) of each LV smart sensor is calculated. The fault line can be identified by an abrupt change value of AMV at LV side. Next, by finding the position of the maximum value of this AMV from LV sensors on the fault line, the fault location can be pinpointed to two neighboring distribution transformers. The proposed method has been proven to be efficient and reliable by simulation studies.

A large core size and bending resistance are very important properties of mid-infrared energy transfer fibers, but large core sizes usually lead to a deterioration of bending properties. A negative-curvature nested node-free anti-resonant hollow-core fiber (AR-HCF) based on quartz is proposed. It was made by adding a nested layer to a previous AR-HCF design to provide an additional anti-resonance region while keeping the gap between adjacent tubes strictly correlated to the core diameter to produce a node-free structure. These features improve the fiber’s bending resistance while achieving a larger core diameter. The simulation results show that the radial air-glass anti-resonant layer is increased by the introduction of the nested anti-resonant tube, and the weak interference overlap between the fiber core and the cladding mode is reduced, so the fiber core’s limiting loss and the sensitivity to bending are effectively reduced. When the capillary wall thickness t of the fiber is 0.71 μm, the core diameter D is 70 μm, the ratio of the inner diameter of the cladding capillary to the core diameter d/D is 0.62, and the diameter of the nested tube is d0=29 μm, the fiber has a lower limiting loss at the wavelength of 2.79 μm, and the limiting loss is 3.28×10-4 dB/m. At the same time, the optimized structure also has good bending resistance. When the bending radius is 30 mm, the bending loss is only 4.72×10-2 dB/m. To our knowledge, this is the first research to achieve an anti-bending low-loss micro-structure hollow fiber with a bending radius of less than 30 mm in the 2.79 μm band. An anti-bending low-loss anti-resonant hollow-core fiber with this structure constitutes a reliable choice for the light guiding system of a 2.79 μm band erbium laser therapy instrument.

Using desi-cow waste products like Jeevamrit, natural farming is widespread among farmers for improving soil biology and productivity. Jeevamrit enhances soil chemical and microbiological properties without needing large quantities of farmyard manure (FYM), as a sustainable farming practice with a reduced carbon footprint. Despite its traditional use, Jeevamrit faces criticism due to a lack of scientific evidence. This study investigated the comparative effect of Jeevamrit and chemical fertilizers on the growth and yield of marigold cv. Siracole. In this study mother block of marigold was raised for both summer and winter seasons. The cuttings were harvested from the mother block and then kept for rooting. The rooted cuttings were planted at monthly intervals and evaluated for flowering parameters and compared to those treated with RDF (30:20:20 N, P, and K g/m2). Soil supplied with Jeevamrit enhanced bacteria (26.33%), fungi (18.92%), and actinomycetes (31.21%) populations compared over the recommended dose of fertilizers (RDF) (i.e. N:P: K @ 30:20:20 g m-2). Jeevamrit-treated plants have marketable flower yield per square meter (3.98 %) and shelf life (9.93 %) compared to RDF. The study concludes that Jeevamrit @ 2 liter m-2 is a sustainable and effective alternative to traditional fertilizers for enhancing marigold production in the mid-hills of the Himalayan region, where natural farming is already accepted.

In this work a research on pulsed electrochemical micromachining of Stainless Steel is presented. A suitable equipment to study the process is described as well as a fitting procedure to machine and measure the variables involved. A tool of Tungsten with a tip of about 5 mm diameter sunk in an electrolyte of NaNO₃ is used for the process. The pulse on-time must be maintained in the order of ns to achieve a good current confinement, since the tool is active. Some experiments were made to assess the most important variables of the process, as current confinement, surface roughness, material removal rate and efficiency. It is observed that the current confinement get worse when the pulse on-time increases, as well as surface roughness. The material removal rate and the efficiency increase with the voltage amplitude and the pulse on-time. The voltage amplitude must be higher than 12 V so that the phenomenon of passivation disappears. There is a compromise in the choice of the variables, so a suitable combination of parameters is determined so that a good material removal rate with an acceptable result is achieved.

The province of Macerata, Italy, is a topographically complex region which has been little studied in terms of its temperature and precipitation climatology. Temperature data from 81 weather stations and precipitation data from 55 rain gauges were obtained, and, following quality control procedures, were investigated on the basis of 3 standard periods: 1931-1960, 1961-1990 and 1991-2014. Spatial and temporal variations in precipitation and temperature were analysed on the basis of six topographic variable (altitude, distance from the sea, latitude, distance from the closest river, aspect, and distance from the crest line). Of these, the relationship with altitude showed the strongest correlation. Use of GIS software allowed investigation of the most accurate way to present interpolations of these data and assessment of the differences between the 3 investigated periods. The results of the analyses permit a thorough evaluation of climate change spatially over the last 60 years. Generally, the amount of precipitation is diminished while the temperature is increased across the whole study area, but with significant variations within it. Temperature increased by 2 to 3°C in the central part of the study area, while near the coast and in the mountains the change is between about 0 and 1°C, with small decreases focused in the Appennine and foothill belt (-1 to 0°C). For precipitation, the decrease is fairly uniform across the study area (between about 0-200 mm), but with some isolated areas of strong increase (200-300 mm) and only few parts of territory in which there is an increase of 0-200 mm, mainly in the southern part of the coast, to the south-west and inland immediately behind the coast. The monthly temperature trend is characterized by a constant growth, while for precipitation there is a strong decrease in the amount measured in January, February and October (between 25 and 35 mm on average).

Land Surface Temperature (LST) estimation has been studied for several purposes, while the optimal method of estimating the LST has not been criticized yet. This research explores the optimum method in Land Surface Temperature (LST) estimation using LANDSAT-8 imagery data. Four different LST retrieval approaches, the Radiative Transfer Equation-based method (RTE), the Improved Mono-Window method (IMW), the Generalized Single-Channel method (GSC), and the Split-Window algorithm (SW), were calculated to present the LSTs over Buriram Town Municipality, Thailand. The calculated LSTs from these four methods were compared with the ground-based temperature data, taken on the same date and time of the employed LANDSAT-8 images. For this reason, the optimum method of the LST calculation was justified by considering the lowest normalized root means square error (NRMSE) values. As a result, the SW algorithm presents an optimum method in LST estimation. Regarding the SW, this algorithm requires not only the atmospheric profiles during satellite acquisition but also the retrieval of several coefficients. Besides, the LST retrieval method based on the SW algorithm is sensitive to water vapor content and coefficients. Although the SW algorithm is an optimum method explored in this study, it is emphasized that the adjustable values of coefficient response to the atmospheric state may be recommended. With these conditions, the SW algorithm can generate the land-surface temperature over the mixed land-use and land cover on the LANDSAT-8 images.

Coal bottom ash (CBA) is a byproduct of coal-burning power plants. This material can be used as a fine aggregate replacement in concrete to reduce global natural material depletion. Concrete usage is increasing rapidly; subsequently, the industry’s carbon footprint is increasing. Using CBA in the construction industry will reduce the technical and economic problems associated with power plants by reducing solid waste. This project aimed to determine if adding new sustainable materials, such as CBA, to concrete will reduce natural raw material usage, energy consumption, and greenhouse gas emissions while improving performance. This study included two projects: comparing increased CBA content to the two-control project and determining the optimum content based on the compressive strength. The optimum CBA content is 50%, which reduces fine aggregate usage in a concrete mix by 50% while maintaining equivalent or better concrete strength than a pure Portland concrete mix without CBA. The air content of the concrete mix containing % CBA decreased with increased CBA content and compressive strength, possibly due to the spacing factor of the voids in the mix and CBA’s porous and fineness behavior. The CBA optimum content had a unit weight lower than the controls for both projects, which makes the CBA mix a lightweight concrete. Using this material can significantly reduce natural material usage and environmental harm by reducing CBA waste disposal and improving concrete performance.

The design of curved surface sliders (CSS) based on the elastic response spectrum is done by iteration to find the combination of friction coefficient and displacement capacity which satisfies the condition that the maximum horizontal CSS force is equal to the horizontal force of the structure. Although this CSS design is valid it does not necessarily minimize structural acceleration. This paper therefore describes the optimum CSS design for minimum structural acceleration. All valid CSS designs and the optimum CSS design are represented by their associated trajectory in the elastic response spectrum plane which visualizes the optimization problem. The results demonstrate that the optimum CSS design is not obtained at maximum tolerated effective damping ratio. The subsequent sensitivity analysis describes how much the structural acceleration increases if the actual friction coefficient of the real CSS deviates from its optimum design value. The analysis points out that the increase in structural acceleration is approximately one order of magnitude smaller than the deviation in friction. The sensitivity data may be used by structural engineer to determine tolerable deviations in friction coefficient which still results in acceptable structural accelerations.

Accurate and reliable mid-long runoff prediction (MLTRP) is of great importance in water re-sources management. However the MLTRP is not suitable in each basin and how to evaluate the applicability of MLTRP is still a question. Therefore, the total mutual information (TMI) index is developed in this study based on the predictor selection method using mutual information (MI) and partial MI (PMI). The relationship between the TMI and the predictive performance of five models is analyzed by applying five models in 222 forecasting scenarios in Australia. The results over 222 forecasting scenarios demonstrate that, compared with the MI, the developed TMI index can better represent the available information in the predictors, and has more significant negative correlation with the RRMSE with the correlation coefficient between -0.62 and -0.85. This means the model's predictive performance will become better along with the increase of TMI, and there-fore the developed TMI index can be used to evaluate the applicability of MLTRP. When TMI is more than 0.1, the available information in the predictors can support the construction of MLTRP models. In addition, the TMI is used to partly explain the difference of predictive performance among five models. In general, the complex models, which can better utilize the contained infor-mation, are more sensitive to the TMI, and have more significant improvement in terms of predic-tive performance along with the increase of TMI. This research can provide support for the study of MLTRP.

A long-standing problem in the understanding of deep-water turbidite reservoirs relates to how the three-dimensional evolution of deep-water channel systems evolve in response to channel filling on spatio-temporal scales, and how depositional environments affect channel architecture. The 3-D structure and temporal evolution of late Miocene deep-water channel complexes in the southern Taranaki Basin, New Zealand is investigated, and the geometry, distribution and stacking patterns of the channel complexes are analyzed. Two recently acquired 3-D seismic datasets, the Pipeline-3D (proximal) and Hector-3D (distal) are analyzed. These surveys provide detailed imaging of late Miocene deep-water channel systems, allowing for the assessment of the intricate geometry and seismic geomorphology of the systems. Seismic attributes resolve the channel bodies and the associated architectural elements. Spectral decomposition, amplitude curvature, and coherence attributes reveal NW-trending straight to low-sinuosity channels and less prominent NE-trending high-sinuosity feeder channels. Stratal slices across the seismic datasets better characterize the architectural elements. The mapped turbidite systems transition from low-sinuosity to meandering high-sinuosity patterns, likely caused by a change in the shelf-slope gradient due to localized structural relief. Stacking facies patterns within the channel systems reveal the temporal variation from a depositional environment characterized by sediment bypass to vertically aggrading channel systems.

Navigation is the most challenging issue in autonomous vehicles. Researchers in the current era have developed many Artificial Intelligence techniques to navigate, generate paths, and avoid obstacles for optimum path planning for autonomous vehicles. Different studies have investigated bio-inspired techniques to overcome the navigation issue, including obstacle avoidance. This paper uses new meta-heuristic optimization techniques called Dragonfly Algorithm (DA) to set the goal by detecting and avoiding obstacles with minimum human interference. For effective results, the Dragonfly-Fuzzy hybrid algorithm is analyzed over the unstructured environment because individual techniques may not be sure of an optimal solution over all configurations. The main advantage of the proposed hybrid controller is that it combines the multiple features of different approaches into a single controller. This paper compares simulation and experimental findings over various environmental conditions to the individual algorithm. Regarding time and path optimization, the hybrid Dragonfly-Fuzzy controller performs better than the respective controller.

The construction sector has begun to embrace the digital revolution, intending to improve efficiency. How, on the other hand, should the industry adopt digital tools? And how should the connection between humans and technology function? This study aims to shed light on how the construction sector may bridge the gap between AI deployments’s potential and realized advantages. This article presents research based on a comprehensive review of the literature, case studies of Speller Metcalfe, a design-build and refurbishment project in Malvern, England, Jacobsen Construction, a project digitizing the planning process in Salt Lake City, Utah, USA, and Menkes Development Inc., real-time visibility to construction site insights and data-driven decision-making in Toronto, Canada. The experiences gained via this study show that it is feasible to acquire expertise while adopting sophisticated technologies, such as artificial intelligence, by installing fundamental digital tools (AI). However, when it comes to AI, the level of trust between humans and machines will be the deciding element in its success. This article is a pioneering effort in examining the deployment of AI and how people and technology should interact. This study is limited to three case studies and three digital technologies. To further the study, it is suggested to debate the adaptation of AI on the user's premises, gather more empirical data, and examine case studies from different sectors.

This research proposes a framework to assist wind energy developers to select the optimum deployment site of a wind farm by considering the Round 3 zones in the UK. The framework includes optimisation techniques, decision-making methods and experts’ input in order to help stakeholders with investment decisions. Techno-economic, Life Cycle Costs (LCC) and physical aspects for each location are considered along with experts’ opinions to provide deeper insight into the decision making process. A process on the criteria selections is also presented and seven conflicting criteria are being considered in TOPSIS methods in order to suggest the optimum location that was produced by the NSGAII algorithm. Seagreen Alpha was the most probable solution, followed by Moray Firth Eastern Development Area 1, which demonstrates by example the effectiveness of the newly introduced framework that is also transferable and generic. The outcomes are expected to help stakeholders and decision makers to make more informed and cost-effective decisions under uncertainty when investing in offshore wind energy in the UK.

To bring to the fore the aim of this research, effects of fluctuating temperature, was measured against food and nutrition security in the region using food production index, and undernourished population growth rate as proxies; controlled over share of arable land, irrigation, population and labour share for agriculture. Dynamic panel of generalized method of moments (GMM) was adopted, the period 2000 to 2016 were considered and 29 countries in sub-Sahara Africa were selected within the empirical framework of global water balance as mentioned by Rai and Singh (2012). Findings from the study reveals that the short run effect of temperature increase in degrees pose at least -3.1% negative and significant impact effects on the food production while the long run elasticity hits -7.5% and the controlled effect on arable land revealed a positive impact on the food production to the tune of 3.9%. Contrarily, arable land expansion reduces the under nourished population by -8.55%. Population increase on the other hand increases undernourished population in the region to the tune of 11.95%. The study therefore recommended expansion in the arable land and encourages population control policy in order to negate the undesired effects of temperature on food and nutritional security.

Toshiba devised the bladeless fan (or Air Multiplier) concept in 1981. Researchers like James Dyson and Jafari et al. further developed it. Bladeless fans are more energy-efficient, safer due to the hidden blades, easier to clean, and more adjustable than conventional fans. From a performance point of view, bladeless fans are better because they multiply mass flow rate, eliminate buffeting, consume less power, and are quieter. This paper investigates the influence of the airfoil’s outlet slit thickness on the discharge ratio by varying the outlet slit thickness of an Eppler 473 airfoil from 1.2 mm to 2 mm in intervals of 0.2 mm. Results indicated that smaller slits showed higher discharge ratios. The airfoil with a 1.2 mm slit thickness showed a discharge ratio of 18.78, a 24% increase from the discharge ratio of the 2 mm slit. The effect of outlet angle on the pressure drop across the airfoil was also studied. Outlet angles were varied from 16∘ to 26∘ by an interval of 2∘. The airfoil profile with a 24∘ outlet angle showed a maximum pressure difference of 965 Pa between the slit and leading edge. In contrast, the 16∘ outlet angle showed the least pressure difference of 355 Pa. Parameters such as average velocity, turbulent kinetic energy, the standard deviation of velocity and outlet velocity magnitude was used to assess the performance of airfoil profiles used in bladeless fan.

Human motor planning combines such interesting aspects as modular organization in motor primitives and characteristics of stochastic optimality. Motor primitives aided in the description of motor skill learning. In this study, for the first time, an interpretation is proposed to explain how motor primitives are shaped in a stochastic optimality process.To this end, sensory information is assumed to be random variables at each moment. Theoretically, the results confirmed that the variability of a movement increased with passing time. As a result, motor planning should be performed in shorter durations to achieve an accurate movement. It means that a task should be divided into several subtasks at various stages of time. Moreover, theoretically, the results confirmed that motor planning is statistically optimal if the movement is planned in minimum jerk space, which is in accordance with what is reported in the literature. Comparing the proposed mathematical model with the results of experimental data in two different types of motor action (i.e., arm reaching movement and sit-to-stand transfer from a chair) confirmed that the proposed model can be considered a framework to investigate the effect of bottom-up information on human motor planning level. Further experiments need to investigate it more deeply.

The purpose of this paper is to evaluate the timing of innovative investment in technology product life cycles using a compound binomial option with management flexibility. Considering the business cycles changes in the macroeconomic will affect consumer purchasing power. The focus is how to evaluate the optimal investment strategy and the project value. It was applied to different product stages (three stages including production innovation, manufacture innovation, and operation innovation) and factored to different risks to build a technology innovation strategy model. An aim of this study is the options premium of the best strategy timing for each innovation stage. Its application of the compound binomial options for the manufacture innovation will only be considered after the execution of the production innovation. The same condition is applied to the operation innovation, which will only be considered after the execution of the manufacture innovation. Then, this paper constructs the dynamic investment sequential decision model, assesses the feasibility of an investment strategy, and makes a decision on the appropriate project value and options premium for each stage under the possible change of Gross Domestic Product (GDP). This paper investigates the product life cycle innovation investment topic by using the compound binomial options method and will provide a more flexible strategy decision compared with other trend forecast criteria.

Both globally and in Hungary, agriculture is one of the industries that is most vulnerable to weather and climate extremes. Intense temperature rises, spatial and temporal variations in precipitation, and significant changes in extreme climatological and weather parameters have contributed to changes in the conditions of cropland, crop losses, and impacts on crop quality in recent years. This paper depicts the transformation of the domestic agricultural sector due to the extreme drought shock of 2022, as well exploring the adaptation strategies applied. The research is based on official agro-climate database and crop data, and the temperature, precipitation, and radiation during the growing season are all examined. The agro-meteorological properties in Hungary had to be investigated for the entire year and all four of its seasons, with indicator analysis projected onto the ever-increasing and dormant seasons. Long-term climate analysis is necessary to understand the historic drought of 2022 and the success of future adaptation and mitigation techniques. The results can help smallholders effectively reduce the adverse impacts of drought conditions, thereby increasing their adaptation to similar shocks.

Bluecat is a recently proposed methodology to upgrade a deterministic model (D-model) into stochastic (S-model), based on the hypothesis that the information contained in a time series of observations and the concurrent predictions by the D-model is sufficient to support this upgrade. Prominent characteristics of the methodology are its simplicity and transparency, which allow easy use in practical applications, without sophisticated computational means. Here we utilize the Bluecat methodology and expand it in order to be combined with climatic model outputs, which often require extrapolation out of the range of values covered by observations. We apply the expanded methodology to the precipitation and temperature processes in a large area, namely the entire territory of Italy. The results showcase the appropriateness of the method for hydroclimatic studies, as regards the assessment of the performance of the climatic projections, as well as their stochastic conversion with simultaneous bias correction and uncertainty quantification.

In Bangladesh, climate change is a major concern because of its geophysical location and climate dependent agriculture. As sessile organisms, crops plants have to face difficulties often in this environmentally vulnerable country. Therefore, this study examines the seasonal trend of two climatic parameters viz. temperature (maximum and minimum) and rainfall over a period of 1983 to 2013. Besides, this study provides insight into the relationship between climatic parameters and crop yield of two major crops viz. rice and wheat during 1997-2013. To assess the relationship of climatic parameters with time and yield using Pearson correlation analysis, time series data used at an aggregate level. SPSS software utilized for this analysis. The cropping seasons such as rice growing seasons Aus (summer rice), Aman (autumn rice) and Boro (winter rice) exhibited a significant increase in maximum and minimum temperature. Rainfall found to have a decreasing trend for all the seasons. This study also revealed that the climatic parameters had significant effects on rice yield, but these results varied among three rice crops. Maximum temperature had positive effects on all rice yields, especially on Aus and Aman. Minimum temperature had a negative effect on Aman rice yield but a positive effect on Aus rice yield. Wheat yield negatively associated with temperature. Rainfall exhibited negative relation with both rice and wheat yield.

Planetary waves in the mesosphere are studied using observational data and models to establish their origin, as there are indications of their generation independently of waves in the stratosphere. The quantitative relationships between zonal wave numbers m = 1 (wave 1) and m = 2 (wave 2) were studied with a focus on the mid-latitude mesosphere at 50N latitude. Aura Microwave Limb Sounder measurements were used to estimate wave amplitudes in geopotential height during the 2020–2021 winter major sudden stratospheric warming. The moving correlation between the wave amplitudes shows that, in comparison with the anticorrelation in the stratosphere, wave 2 positively correlates with wave 1 and propagates ahead of it in the mesosphere. A positive correlation r = 0.5–0.6, statistically significant at the 95% confidence level, is observed at 1–5-day time lag and in the 75–91 km altitude range, which is the upper mesosphere–mesopause region. Wavelet analysis shows a clear 8-day period in waves 1 and 2 in the mesosphere at 0.01 hPa (80 km), while in the stratosphere–lower mesosphere the period is twice as long at 16-days; this is statistically significant only in wave 2. Possible sources of mesospheric planetary waves are discussed.

Safely resuming sporting events while the coronavirus is spreading is challenging – yet possible – if the science is taken into account. Two main ways the coronavirus can spread among football players is through air-suspended microdroplets (and possibly aerosols), and via contact with contaminated surfaces. Here we estimated virus survival in dried saliva droplets on a football pitch (i.e., on the grass) and on the ball itself, and compared these measures between mid-day and nighttime matches. We find, based on experiments with the enveloped phage Phi6 – a surrogate for SARS-Cov-2 – that while the virus survives reasonably well on both pitch and ball during a nighttime match (~10% survival), virtually no viruses survived the 90-minute duration of a mid-day match on a hot, sunny day. These results, taken together with studies reporting rapid deactivation of coronavirus in aerosols by sunlight, suggest that playing football in mid-day reduces the likelihood of transmission between players, and thus increases players’ safety.

Ambrosia trifida is a kind of malignant invasive plant, which has very high reproductive and en-vironmental adaptability. Through strong resource acquisition ability and allelopathy, it could inhibit the growth and reproduction of surrounding plants, destroy the stability of an invasive ecosystem. It is very important to predict the change of suitable distribution area of Ambrosia trifida with climate change before implementing scientific control measures. Based on 106 Ambrosia trifida distribution data and 14 environmental data, the optimal parameter combination (RM = 0.1, FC = LQ) was obtained by using the MaxEnt model optimized by Kuenm package, the potential suit-able areas of Ambrosia trifida in Northeast China under three different climate scenarios (RCP2.6, RCP4.5, RCP8.5) with different emission intensities in the future (2050,2070) were predicted. The changes of Ambrosia trifida suitable area in Northeast China under three climate scenarios were compared, and the relationship between the change of suitable area and emission intensity was analyzed. In general, the suitable area of Ambrosia trifida in Northeast China will expand gradually in the future, and the area of its highly suitable area will also increase with the increasing emission intensity, which is unfavorable to the control of Ambrosia trifida.

Polarisation analysis in the mid-infrared fingerprint region was carried out on thin (∼1μm) Si and SiO2 films evaporated via glancing angle deposition (GLAD) method at 70∘ to the normal. Synchrotron-based infrared microspectroscopic measurements were carried out on the Infrared Microspectroscopy (IRM) beamline at Australian Synchrotron. Specific absorption bands, particularly Si-O-Si stretching vibration, was found to follow the angular dependence of ∼cos2θ, consistent with the absorption anisotropy. This unexpected anisotropy stems from the enhanced absorption in nano-crevices, which have orientation following the cos2θ angular dependence as revealed by Fourier transforming the image of the surface of 3D columnar films and numerical modeling of light field enhancement by sub-wavelength nano-crevices.

The realization of a perfect absorber A = 1 with transmittance and reflectance T=R=0 by a thin metasurface is one of the hot topics in recent nanophotonics prompted by energy harvesting and sensor applications (A + R + T =1 is the energy conservation). Here we tested optical properties of over 400 structures of metal-insulator-metal (MIM) metasurfaces for a range of variation in thickness of insulator, the diameter of a disc and intra-disc distance experimentally and numerically. Conditions of a near-perfect absorption A > 95% with simultaneously occurring anti-reflection property (R < 5%) were experimentally determined. Differences between the bulk vs. nano-thin film properties at mid-IR of the used materials can be of interest for plasmonic multi-metal alloys and high entropy metals.

Federated learning is a decentralized topology of deep learning, that trains a shared model through data distributed among each client (like mobile phones, wearable devices), in order to ensure data privacy by avoiding raw data exposed in data center (server). After each client computes a new model parameter by stochastic gradient decrease (SGD) based on their own local data, all locally-computed parameters will be aggregated in the server to generate an updated global model. Almost all current studies directly average different client computed parameters by default, but no one gives an explanation why averaging parameters is a good approach. In this paper, we treat each client computed parameter as a random vector because of the stochastic properties of SGD, and estimate mutual information between two client computed parameters at different training phases using two methods in two learning tasks. The results confirm the correlation between different clients and show an increasing trend of mutual information with training iteration. However, when we further compute the distance between client computed parameters, we find that parameters are getting more correlated while not getting closer. This phenomenon suggests that averaging parameters may not be the optimum way of aggregating trained parameters.

Introductions- Liveable housing environments face the menace of global climate change. In-frastructure (including buildings and houses) continuously experiences significant impacts ex-acerbated by natural variability in climate. The study addressed how climate change impacts the resilience of residential buildings, increased maintenance frequency, and the wellbeing and comfort of residents in UK residential buildings. Design/Methodology/Approach: This study used deductive reasoning and an empirical epis-temological methodology as a data-collecting basis to evaluate primary information obtained via a questionnaire. Regression analysis was ultimately employed to analyse the collected da-ta. Result/Discussions: The findings show a significant relationship between climate change and the wellbeing of the occupants of UK residential buildings. Also, the results show that social wellbeing is more important to the occupants than mental and physical wellbeing. It reveals that residential buildings in the UK suffer the cost of maintenance due to continuous reduc-tion in the building fabric's resilience to the impacts of climate change; for instance, a recent increase in rainfall/storms results in unprecedented flooding, which continues to damage the UK residential building fabrics.

The choice of holiday destinations is highly depended on climate considerations. Nowadays, since the effects of climate crisis are being increasingly felt, the need of accurate weather and climate services for hotels is crucial. Such a service could be beneficial for both the future planning of tourists’ activities and destinations and for hotel managers as it could help in decision making about the planning and expansion of the touristic season, due to a prediction of higher temperatures for a longer time span, thus causing increased revenue for companies in the local touristic sector. The aim of this work is to calculate predictions on climatic variables using statistical techniques as well as Artificial Intelligence (AI) for a specific area of interest utilising data from in situ meteorological station, and produce valuable and reliable localised predictions with the most cost-effective method possible. This investigation will answer the question of the most suitable prediction method for time series data from a single meteorological station that is deployed in a specific location. As a result, an accurate representation of the microclimate in a specific are is achieved. To achieve this high accuracy in situ measurements and prediction techniques are used. As prediction techniques, Seasonal Auto Regressive Integrated Moving Average (SARIMA), AI techniques like the Long-Short-Term-Memory (LSTM) Neural Network and hybrid combinations of the two are used. Variables of interest are divided in the easier to predict temperature and humidity that are more periodic and less chaotic, and the wind speed as an example of a more stochastic variable with no known seasonality and patterns. Our results show that the examined Hybrid methodology performs the best at temperature and wind speed forecasts, closely followed by the SARIMA whereas LSTM perform better overall at the humidity forecast, even after the correction of the Hybrid to the SARIMA model.

Portugal, in line with the European Union, is aiming for carbon neutrality by 2050 (Net 1 Zero), which implies a transition to sustainable energy sources. Climate change is all too evident, extreme weather periods are occurring in a cyclical manner, with greater brevity to such an extent that the grid operator must deal with production scenarios where it can no longer rely on hydroelectric production given the recurring drought situation. This situation increases dependence on thermal production using natural gas and imports. This has significant economic implications. Portugal has exploited its onshore wind potential, reaching an installed capacity of 5.671 MW by 2022. However, the expansion of onshore wind energy is limited to reinforcing existing infrastructure. To overcome these challenges, it is necessary to expand the exploitation of offshore wind potential that is already underway. This article proposes the location of offshore wind production platforms along the Portuguese coast. This allows for an analysis of offshore production and its optimization according to the minimum cost per MWh in the face of extreme scenarios, i.e., in periods of extreme drought where hydroelectric production capacity is practically non-existent. The model is fed by using market price indications and the amount of energy needed for the following day. Using forecast data, the model adapts offshore wind production for the following day according to the minimization of the average market price. The results of the simulations allow us to conclude that despite the high cost of offshore technology (in deep waters), in extreme climate scenarios, it enables cost reduction and a clear decrease in imports.

Water is essential to all life-forms including various ecological, geological, hydrological, and climatic processes/activities. With changing climate, associated El Nino/Southern Oscillation (ENSO) events appear to stimulate highly uncertain patterns of precipitation (P) and evapotranspiration (EV) processes across the globe. Changes in P and EV patterns are highly sensitive to temperature variation and thus also affecting natural streamflow processes. This paper presents a novel suite of stochastic modelling approaches for associating streamflow sequences with climatic trends. The present work is built upon a stochastic modelling framework HMM_GP that integrates a Hidden Markov Model with a Generalised Pareto distribution for simulating synthetic flow sequences. The GP distribution within HMM_GP model is aimed to improve the model's efficiency in effectively simulating extreme events. This paper further investigated the potentials of Generalised Extreme Value Distribution (EVD) coupled with an HMM model within a regression-based scheme for associating impacts of precipitation and evapotranspiration processes on streamflow. The statistical characteristic of the pioneering modelling schematic has been thoroughly assessed for their suitability to generate/predict synthetic river flows sequences for a set of future climatic projections. The new modelling schematic can be adapted for a range of applications in the area of hydrology, agriculture and climate change.

The Badenian/Sarmatian boundary in the Central Paratethyan basins is characterized by a change from open marine conditions during the late Badenian to the assumed brackish conditions during the early Sarmatian. Foraminiferal and palynological results of the Badenian/Sarmatian boundary interval in the Babczyn 2 borehole (SE Poland) showed that the studied interval accumulated under variable, unstable sedimentary conditions. The Badenian/Sarmatian boundary as correlated with a sudden extinction of stenohaline foraminifera is interpreted as due to the shallowing of the basin. The lack of foraminifera and palynomorphs just above the Badenian/Sarmatian boundary can reflect short-term anoxia. The composition of euryhaline assemblages characteristic for the lower Sarmatian part of the studied succession indicates marine to hypersaline conditions.

The aim of this article is to propose a core game theory model of transaction costs wherein it is indicated how direct costs determine the probability of loss and subsequent transaction costs. The existence of optimum is proven, and the way in which exposure influences the location of the optimum is demonstrated. The decisions are described as a two-player game and it is discussed how the transaction cost sharing rule determines whether the optimum point of transaction costs is the same as the equilibrium of the game. The dispute between actors regarding changing the share of transaction costs to be paid by each party is modeled by a non-cooperative bargaining game. Requirements of efficient transaction cost sharing rules are defined, and it is posited that solution exists which is not unique. Policy conclusions are also devised based on principles of design of institutions to influence the nature of transaction costs.

Keeping the bus voltage within acceptable limits depends on dispatching reactive power. Power quality improves as a result of creating an effective power flow system, which also helps to reduce power loss. Therefore, Optimal Reactive Power Dispatch (ORPD) studies aim at designing appropriate system configurations to enable a reliable operation of power systems. Establishment of such a configuration is handled through control variables in power systems. On the other hand, installing Distributed Generation Unit (DGU) into a power system can have an important effect on power quality and power loss minimization. In this paper, Grey Wolf Optimization (GWO method is applied to ORPD problem for the first time, to find optimal placement of newly installed DGUs at the power system. Active power loss and voltage minimization have been minimized by optimizing the control variables while keeping them within their upper and lower bounds, and by finding the optimal placement of a newly installed DGU in power system. On the basis of IEEE 30 bus and IEEE 118 bus systems, performance of the suggested approach is investigated. A comparison is also performed among the proposed method and some other methods. Test results demonstrate that the resulting configuration contributes to growing the rate of renewable integration to a power system. The results also indicate that the suggested optimization approach applied to ORPD problem has improved power system performance in terms of both on power loss and voltage deviation. The promising results highlight the potential of the GWO algorithm to facilitate the integration of renewable power sources, and its role in promoting sustainable energy solutions.

The European pear is a climacteric fruit species characterized by high storability. 'Conference', a pear cultivar very popular on the market, can be stored in a CA room without major losses for half a year. However, for ‘Conference’ storage to be successful, the fruit must be harvested fully developed even before it enters the climatic maturation phase. Harvested too early or too late, pears will taste bad, have physiological disorders and will be poorly storable. Among the various methods used to determine the optimal harvest date, the degree-days method, which relies of the sum of active temperatures, seems to be relatively accurate and easy to apply. During 11 years of study, ‘Conference’ pears were harvested on 4 dates (every 4-5 days) chosen based on measurements and observations, and then, after a six-month storage period, the optimum harvest date was determined. During the growing season, temperature was measured using an automatic weather station to calculate the sum of active temperatures from full bloom to the optimal harvest date. Measurements made after storage were analysed and the sum of active temperatures needed for the proper development of ‘Conference’ pear was calculated to be 2469 degree days. The calculations are very accurate because the dispersion calculated using the standard deviation was only 20 °. The base temperature with the smallest error was 0 °. On the basis of the study results, this method can be recommended as useful for determining the optimal harvest date.

The Zero Trust Architecture (ZTA) security system follows the "never trust, always verify" principle. The process constantly verifies users and devices trying to access resources. This paper describes how Microsoft Azure uses ZTA to enforce strict identity verification and access rules across the cloud environment to improve security. Implementation is time-consuming and difficult. Azure's extensive services and customizations require careful design and implementation. Azure administrators struggle to navigate and change configurations due to its complex user interface (UI). Each Azure ecosystem component must meet ZTA criteria. ZTA's comprehensive policy definitions, multi-factor and pass-wordless authentication, and other advanced features are tested in a mid-size business scenario. These configuration changes require a solid grasp of Azure's architecture and Zero Trust. Implementing an Azure ZTA reduces vulnerabilities and restricts authorized users' access to critical resources. Implementation is time-consuming and expensive, requires a significant commitment to changing IT procedures, and can be confusing because the same features are available in multiple places. Azure ZTA has shown great potential for both hybrid and cloud-native companies.

Almost 50 papers on surface plasmon resonance biosensors, published between 2016 and mid-2018, are reviewed. Papers concerning the determination of large particles such as vesicles, exosomes, cancer cells, living cells, stem cells and microRNA are excluded, as these are covered by a very recent review. The reviewed papers are categorized into five groups, depending on the degree of maturity of the reported solution: ranging from simple marker detection to clinical application of a previously developed biosensor. Instrumental solutions and details of biosensor construction are analyzed, including the chips, receptors and linkers used, as well as calibration strategies. Biosensors with a sandwich structure containing different nanoparticles are considered separately, as are SPR applications for investigating the interactions of biomolecules. An analysis is also made of the markers determined using the biosensors. Concluding, there is shown to be a growing number of SPR applications in the solution of real clinical problems.

The soil organic matter (SOM) content and stability in natural gypsum soils and soils from mining/industrial areas were compared, in terms of their physical, chemical and micromorphological properties, to determine whether the old brownfield soils were acting as carbon (C) sinks, counteracting increasing carbon dioxide concentrations in the atmosphere. The mining/industrial soils were 50–400 years old, so had been left sufficiently long for full self-restoration. Despite having very different origins, both natural and brownfield soils stored similar amounts of SOM, and had similar pH values, calcium carbonate contents and textures. They were also fully covered with similar grass plant communities. The mining/industrial soils exhibited similar microstructures to the gypsum soils and were often quite porous. The most striking difference between them and the natural gypsum soils was that the mining/industrial soils were strongly polluted with zinc, lead and cadmium. The 50-year-old brownfield soils differed from the others in terms of having a lower state of SOM transformation, with a much higher C/N ratio, lower aggregate water resistance index, lower dehydrogenase activity and greater areas of undecomposed or slightly decomposed plant residues. These parameters in the older (150–400 years) brownfield soils were similar to those of the natural soils.

Construction of Pontoons is based on multiple elements, dimensions and weight. The study has addressed about how the industry of the floating reinforcement concrete precast (pontoons) installs in the factory with the combinations of utility, electricity services, and Internet service. The pontoon bridges are successfully installed in the road for transport or sea for shops. The installation process for pontoons is successfully attempted in a balanced situation above surface of the sea to the resistant of floating precast (pontoons) to any ambient effects such as weather conditions, the movement of the waves or any others effects. The findings elaborate that it is not just a military solution. Pontoon installation can significantly serve for civil purposes.

In deep geological analysis of data, these are input data that are few and include a small set of data. In a small set of case data, it is necessary to obtain reliable data of individual geological variables from this type of data. The paper analyzes the possibility of applying the bootstrap method on variables that are important in the exploration and production of hydrocarbons. The variables analyzed were the following: porosity and total costs of disposal formation water. The case study was made on the data of reservoir "K", field "B" located in the western part of the Sava Depression. The analysis of the results showed the possibility of applying the bootstrap method in the analysis of deep geological data with the application of three different sizes of resampling dataset.

Otodus megalodon is known as the biggest shark ever alive and recent records show this species was only existed in America, Africa and Europe continents in the last Miocene period 20 million years ago (Ma). Recently, megalodon teeth have been discovered in South coast of West Java. Here this study aims to present and model the presence of O. megalodon. The length of the excavated tooth was ranging from 13 to 19 cm. The lithological analysis shows that the tooth was found in Miocene rock layers. Paleogeographic model shows that during Miocene southern parts of Java island were submerged including the recent locations where the megalodon tooth have been found. Half parts of the modeled West Java were an ocean with depth ranging from 0 to 200 m. High habitat use preferences by juvenile megalodon were estimated in the shelf (depth 0-40 m) with the size of 1365 km² . Whereas habitat use preference by adult megalodon was low at this depth. Both juvenile and adult habitat use frequencies were low at a depth of between 80 m and 160 m. Habitat use preferences were increasing at a depth of > 200 m. After Miocene, the paleoclimate records show a decline in temperature and lead to the decline of whale population in ocean. The declining of megalodon’s prey explains the declining of this giant shark especially in post Miocene and early Pliocene periods.

Solar energy is derived from photons of light coming from the sun in a form called radiation. Solar energy finds extensive application in air and water heating, solar cooking, as well as electrical power generation, depending on the way of capturing, converting and distribution. To enable such application, it is necessary to analyze the horizontal tilt angle of horizontal surfaces – in order that when the solar energy reaches the earth surface to be completely absorbed. This paper tends to describe the availability of solar radiation for south-facing flat surfaces. The optimal monthly, seasonal, and annual tilt angles have been estimated for Pristina. The solar radiation received by the incident plane is estimated based on isotropic sky analysis models, namely Liu and Jordan model. The annual optimum tilt angle for Pristina was found to be 34.7°. The determination of annual solar energy gains is done by applying the optimal monthly, seasonal and annual tilt angles for an inclined surface compared to a horizontal surface. Monthly, seasonal and annual percentages of solar energy gains have been estimated to be 21.35%, 19.98%, and 14.43%. Losses of solar energy were estimated by 1.13 % when a surface was fixed at a seasonal optimum tilt angle, and when it was fixed at an annual optimum tilt angle, those losses were 5.7%.

This work is aimed at investigating the capabilities and limits of the mid-fidelity numerical solver DUST for the evaluation of wind turbines aerodynamic performance. In particular, this study was conducted by analysing the benchmarks NREL- 5MW and Phase VI wind turbines, widely investigated in literature by from experimental and numerical activities. The work started by simulating simpler configuration of the NREL- 5MW turbine to progressively integrate complexities such as shaft tilt, cone effects and yawed inflow conditions, offering a detailed portrayal of their collective impact on turbine performance. A particular focus was then given to the evaluation of aerodynamic responses from the tower and nacelle, as well as aerodynamic behavior in yawed inflow condition, crucial for optimizing farm layouts. In the second phase, the work was focused on NREL Phase VI turbine due to the availability of experimental data on this benchmark case. Comparison of DUST simulations results with both experimental data and high-fidelity CFD tools shows the robustness and adaptability of this mid-fidelity solver for this applications, thus opening a new scenario for the use of such mid-fidelity tools for the preliminary design of novel wind turbines configurations or complex environments as wind farms, characterised by robust interactional aerodynamics.

Recent developments in mid-infrared (MIR) spectroscopic ellipsometry enabled by quantum cascade lasers (QCLs) resulted in a drastic improvement in signal-to-noise ratio compared to conventional thermal emitter based instrumentation. Thus, it was possible to reduce the acquisition time for high-resolution broadband ellipsometric spectra from multiple hours to less than 1 second. This opens up new possibilities for real-time in-situ ellipsometry in polymer processing. To highlight these evolving capabilities we demonstrate the benefits of a QCL based MIR ellipsometer by investigating single and multilayered polymer films. The molecular structure and reorientation of a 2.5m thin biaxially oriented polyethylene terephtalate film is monitored during a stretching process lasting 24.5 s to illustrate the perspective of ellipsometric measurements in dynamic processes. In addition, a polyethylene/ethylene vinyl alcohol/polyethylene multilayer film is investigated at continuously varying angle of incidence ( 0∘ – 50∘) in 17.2 s, highlighting an unprecedented sample throughput for the technique of varying angle spectroscopic ellipsometry in the MIR spectral range. The obtained results underline the superior spectral and temporal resolution of QCL ellipsometry and qualify this technique as suitable method for advanced in-situ monitoring in polymer processing.

Existing methods enhance mid-low resolution remote sensing ship detection by feeding super-resolved images to the detectors. Although these methods marginally improve the detection accuracy, the correlation between image super-resolution (SR) and ship detection is under-exploited. In this paper, we propose a simple but effective ship detection method called ShipSR-Det, in which both the output image and the intermediate features of the SR module are fed to the detection module. Using the super-resolved feature representation, the potential benefit introduced by image SR can be fully used for ship detection. We apply our method to the SSD and Faster-RCNN detectors and develop ShipSR-SSD and ShipSR-Faster-RCNN, respectively. Extensive ablation studies validate the effectiveness and generality of our method. Moreover, we compare ShipSR-Faster-RCNN with several state-of-the-art ship detection methods. Comparative results on the HRSC2016, DOTA and NWPU VHR-10 datasets demonstrate the superior performance of our proposed method.

The aim of the research was to study the influence of the calving season in the conditions of the upcoming climate changes on the productive traits of dairy cows in Bulgaria. The study was conducted in a cattle farm with a capacity of 500 dairy cows, loose-housed in open free stall barn (shed type). In the research 286 lactations of 199 Holstein cows from the studied farm were included. The cows with the highest average milk yield for lactation calved in the spring - 8522.2 kg, and the cows with the lowest milk yield calved in the summer - 8082.7 kg. Cows calved in the spring had the highest maximum daily milk yield (lactation peak) - 38 kg, and the lowest in the summer - 35.7 kg. Regarding the composition indicators of milk, fat and protein content, no significant effect of the calving season was found, but a tendency for the lowest values for the percentage of fat in milk was reported for cows calved in the summer - 3.68%, and the most - high for those calved in the spring - 3.71%. Regarding the percentage of protein in the milk, the lowest values were for cows that calved in autumn - 3.19%, and the highest for cows that calved in summer - 3.27%.

Air pollution is responsible for any adverse effects on human beings. Thermal discomfort, on the other hand, is able to overload the human body and eventually provoke health implications due to the heat imbalance. Methods: The aim of the present work is to study the behavior of two bio-climatic indexes and statistical characteristics of the air quality index for Sofia city - the capital of Bulgaria for the period 2008 - 2014. The study is based on WRF-CMAQ model system simula-tions with a spatial resolution of 1 kilometer. The air quality is estimated by the air quality index, taking into account the influence of different pollutants and the thermal conditions by two indi-ces, respectively, for hot and cold weather. Results: It was found that half of the heat and cold index categories are present in the simulations. Their distribution has some spatial features. All air quality categories are present in the domain, with dominance only of the O3 and PM10. Conclu-sions: It was found that Sofia is not so hot and air polluted place, but in some situations, people have to have some concerns when intend to be outdoors for a prolonged time.

A tunable quantum cascade laser (QCL) spectrometer was used to develop methods for detecting and quantifying high explosives (HE) in soil based on multivariate analysis (MVA) and artificial intelligence (AI). For quantification, mixes of 2,4-dinitrotoluene (2,4-DNT) with concentrations from 0% to 20% w/w were investigated using three types of soils: bentonite, synthetic soil, and natural soil. A Partial least squares regression model was generated for predicting 2,4-DNT concentrations. To increase its selectivity, the model was trained and evaluated using additional analytes as interferences, including other HEs such as PETN, RDX, and TNT and non-explosives such as benzoic acid and ibuprofen. For detection, mixes of different explosives in soils were used to implement two AI strategies. In the first strategy, the spectra of the samples were compared with those of soils recorded in a database to identify the most similar soils based on QCL spectroscopy. Next, a Classical Least Squares preprocessing (Pre-CLS) was applied to soils spectra selected from the database. The parameter obtained based on the sum of the weights of Pre-CLS was then used to generate a simple binary discrimination model for distinguishing between contaminated and uncontaminated soils, achieving an accuracy of 0.877. In the second AI strategy, the same parameter was added to a principal component matrix obtained from spectral data of samples and used to generate multi-classification models based on different machine learning algorithms. A Random Forest model worked best with 0.997 accuracy and allowing to distinguish between soils contaminated with DNT, TNT, or RDX and uncontaminated soils.

Abstract Depending upon altitudinal gradient in the Himalayas, the rate of climate change varies from lowland to upland. The Chitwan Annapurna Landscape (CHAL) is the central part of the Himalayas and covers all bioclimatic zones. Analysis of time series data (1970-2019) of temperature and precipitation was carried out in seven bioclimatic zones extending from lowland Terai to higher Himalayas. The non-parametric Mann-Kendall test was applied to determine the trend, which was quantified by Sen’s slope. Annual and decade interval average temperature, precipitation trends, and lapse rate were analyzed in each bioclimatic zone. Out of seven bioclimatic zones, four zones showed a decreasing precipitation trend (lower tropical, upper tropical, upper subtropical, and alpine bioclimatic zones)at the rate of 1.8, 1.98, 2.06, and 1.80 mm/year, and in lower sub-tropical, temperate, and lower subalpine bioclimatic zones, increasing at the rate of 0.45, 1.81 and 1.28mm/year, respectively. Precipitation did not show any particular trend at decade intervals. The average annual temperature at different bioclimatic zones clearly indicates that temperature at higher elevations is significantly increasing more than at lower elevations. In lower tropical bioclimatic zone (LTBZ), upper tropical bioclimatic zone(UTBZ), lower subtropical bioclimatic zone (LSBZ), upper subtropical bioclimatic zone(USBZ), and temperate bioclimatic zone(TBZ), the average temperature increased by 0.022, 0.030, 0.036, 0.042 and 0.051oC/year, respectively. The decade level temperature scenario revealed that the hottest decade was from 1999-2009. The average temperature was found as 24.1, 21.8, 19.7, 17.5, and 13.3oC in LTBZ, UTBZ, LSBZ, USBZ, and TBZ, respectively, and the average annual precipitation in LTBZ, UTBZ, LSBZ, USBZ, TBZ, LBZ, and ABZ was 2002.1, 2613.1, 2223.9, 3146.9, 1447.2, 952.1, and 361.7mm/year, respectively, in CHAL. With the impact of climate change site and region-specific, this information highlights the need to mitigate climate change in different bioclimatic zones.

Knowledge of a lasers beam’s profile throughout a laser system and experiment can help immensely in diagnosing laser problems and assisting in beam alignment and focusing at a sample. Obtaining such profiles is a trivial task in the ultraviolet-visible wavelength range but more challenging with near-infrared to infrared beams. Scientific grade bolometer arrays, suitable for such a task, do exist but are extremely costly, relatively large and have a large pixel size, of the order of 80 μm, which is adequate for profiling larger beams but poses an issue when trying to profile sub 100 μm beams for example at a focal point. This communication identifies a micro-bolometer array for near- to mid-infrared laser beam profiling, which is extremely low cost. In addition, the device is very compact, enabling use in confined spaces, and has a small, 12 μm, pixel size permitting the profiling of focused laser beams. The best scientific grade device identified has a pixel size of 17 μm. This device is a powerful tool for infrared laser spectroscopists, reducing the time required to measure the spot size of beams and to achieve spatial overlap of multiple infrared beams as used in two-dimensional infrared spectroscopy, saving many hours of setup time. The use of the bolometer array as a spectrographic detector and probe of long-term beam drifts is also demonstrated.

This study posits that for appropriately explaining the complex charland (mid-channel island) processes and formulating policy and planning measures, a comprehensive understanding of the dynamic characteristics of the geomorphological, ecological, and human systems holistically is essential. This is also valid for the territorial and maritime areas of Bangladesh. The objectives of this study are: (i) to analyze the salient features and characteristics of the geomorphological and riparian systems of the Bengal Delta; (ii) to analyze the evolutionary discourse of the legal systems concerning eroded (diluvion) and accreted (alluvion) land in Bangladesh; and (iii) to assess characteristics of coping and adaptation strategies of the charland inhabitants. The findings reveal that the delta-building processes, characterized by the dynamic shifts of river channels, and erosion and accretion of charlands have made the land and water systems of the territory very dynamic and unstable – resulting in consistent displacement of settlers and serious deterioration of their socioeconomic status. The historical evolution of land laws and regulations concerning the accreted land favoured vested interests. As no effective institutional framework and structure presently exists in Bangladesh for resettlement planning, formulation of a comprehensive national resettlement policy is therefore urgently needed.

Conifer bark beetles (Coleoptera: Curculionidae: Scolytinae) are major agents of natural disturbance in temperate forests of the northern hemisphere, capable of killing billions of trees in native forests. The dynamics of these insect populations are influenced by climatic variability. To understand such a relationship, it is necessary to monitor the population fluctuation of the species present over time. In this regard, the objective of the present study was to determine the species community of the genus Dendroctonus, the population fluctuation throughout the months of the year, and the effects of relative humidity, temperature, and precipitation on the fluctuation, at three sites of mixed forests in the Municipality of Bocoyna, Chihuahua, in northern Mexico. For insect monitoring, we used Lindgren funnel traps (with 8 funnels each) baited with semiochemicals. Every two weeks, and during 2 years, we collected, identified, and counted the insects. The identification of the species was based on the external morphology and characteristics of the male seminal rod. Temperature and relative humidity were measured using climate data loggers (HOBOs). We found six Dendroctonus species. We also determined the population fluctuation patterns of D. mexicanus Hopkins, D. frontalis Zimmermann, and D. brevicomis LeConte, species with the highest number of captures at each site. Additionally, the relationship between species abundance and climatic variables was determined. The variable that significantly influenced (P&lt;0.05) abundance was temperature. Relative humidity and precipitation variables did not show a significant relationship (P&gt;0.05).

At an energy flux imbalance of about 1 W m–2, the ocean is storing 90 % of the heat accumulating by global warming. However, neither the causes nor the responsible geophysical processes are sufficiently well understood. More detailed investigations of the different phenomena contributing to the oceanic energy balance are warranted. Here, the role of low-level marine clouds in the air-sea interaction is analysed. TEOS-10, the International Thermodynamic Equation of State of Seawater – 2010, is exploited for a rigorous thermodynamic description of the climatic trend of the Lifted Condensation Level (LCL) of the marine troposphere. Rising Sea-Surface Temperature (SST) at constant Relative Humidity (RH) is elevating marine clouds, cooling the cloud base and reducing the downward thermal radiation. This LCL feedback effect is negative and counteracting ocean warming. At the current global SST of about 292 K, the net radiative heat flux from the ocean surface to the LCL cloud base is estimated to 24 W m–2. Per degree of SST increase, this net flux is expected to be enhanced by almost 0.5 W m–2. The climatic LCL feedback effect is relevant for the ocean’s energy balance and may thermodynamically rigorously be modelled in terms of TEOS-10 equations. LCL height may serve as a remotely measured, sensitive estimate for sea surface relative fugacity, or conventional relative humidity.

The importance of small urban green areas has increased in the context of rapid urbanization and densification of the urban tissue. The analysis of these areas through remote sensing has been limited due to the low spatial resolution of freely available satellite images. We propose a timeseries analysis on 3 m resolution Planet images, using GEOBIA and vegetation indices, with the aim of extracting and assessing the quality of small urban green areas in two different climatic and biogeographical regions – temperate (Bucharest, Romania) and mediterranean (Athens, Greece). Our results have shown high accuracy (over 91%) regarding the extraction of small urban green areas in both cities, across all analysed images. The timeseries analysis showed consistency in location for around 55% of the identified surfaces throughout the entire period. The vegetation indices registered higher values in the temperate region, due to the vegetation characteristics and the planning of the two cities. For the same reasons, the increase in vegetation density and quality, as a result of the distance from the city centre and the decrease in the density of built-up areas is more obvious in Athens. The proposed method provides valuable insights in the distribution and quality of small urban green areas at city level and can represent the ground basis for many analyses, currently limited by poor spatial resolution.

Evaporation from surface water plays a key role in water accounting of basins, water resources management, and irrigation systems management, so simulating evaporation with high accuracy is very important. In this study, two methods for simulating pan evaporation under different climatic conditions in Iran were developed. In the first method, six experimental relationships (linear, quadratic, and cubic, with two input combinations) were determined for Iran’s six climate types, inspired by a multilayer perceptron neural network (MLP-NN) neuron and optimized with the genetic algorithm. The best relationship of the six was selected for each climate type, and the results were presented in a three-dimensional graph. In the second method, the best overall relationship obtained in the first method was used as the basic relationship, and climatic correction coefficients were determined for other climate types using the genetic algorithm optimization model. Finally, the accuracy of the two methods was validated using data from 32 synoptic weather stations throughout Iran. For the first method, error tolerance diagrams and statistical coefficients showed that a quadratic experimental relationship performed best under all climatic conditions. To simplify the method, two graphs were created based on the quadratic relationship for the different climate types, with the axes of the graphs showing relative humidity and temperature, and with pan evaporation was drawn as contours. For the second method, the quadratic relationship for semi-dry conditions was selected as the basic relationship. The estimated climatic correction coefficients for other climate types lay between 0.8 and 1 for dry, semi-dry, semi-humid, Mediterranean climates, and between 0.4 and 0.6 for humid and very humid climates, indicating that one single relationship cannot be used to simulate pan evaporation for all climatic conditions in Iran. The validation results confirmed the accuracy of the two methods in simulating pan evaporation under different climatic conditions in Iran.

The study carried out by simulation, concerns the thermal behavior of an office building’s solar fresh air cooling system, based on a LiBr-H₂O absorption chiller in different climatic conditions. The coefficient of performance (COP) and the solar fraction were considered performance parameters and were analyzed with respect to the operating limits: risk of crystallization and maintaining at least a minimum degassing zone. A new correlation between the required solar hot temperature and the cooling water temperature was established and then embedded in another new correlation between the COP and the cooling water temperature that was used in simulations during the whole cooling season corresponding to each location. It was found that: the solar hot water should be maintained in the range of (80-100) °C depending on the cooling water temperature, the COP of the solar LiBr-H₂O absorption chiller with or without cold storage tank can reach (76.5-82.4) % depending on the location, and the solar fraction can reach (29.5-62.0) % without cold storage tank and can exceed 100 % with cold storage tank, the excess cooling power being available to cover other types of cooling loads: through the building envelope, from lighting, from occupants, etc.

This article presents raw data of biaxial tensile measurements of rat heart passive myocardium conducted in lab scale environment. The passive myocardium of the rat was divided into three regions, namely: left ventricle, mid-wall and right ventricle. The biaxial dataset of passive rat myocardia is presented as stress vs strain of the passive rat myocardium in various regions. The determination of valid material properties of the heart plays an important role in the development computational models. These computational models are useful in studying various scenarios and mechanisms of heart diseases. In addition, valid and accurate materials are critical in the development of new therapies. The dataset presented here is useful in the area of soft tissue mechanics including studying the mechanisms of heart diseases such as myocardial infarction. Accordingly, the evaluation of stress and strain in left ventricle, mid-wall and right ventricle was performed.

This study integrated coastal-watershed models and combined a risk assessment method to develop a methodology to investigate the impact resulting from coastal disasters under climate change. The mid-western coast of Taiwan suffering from land subsidence was selected as the demonstrative area for the vulnerability analysis based on prediction of sea level rise (SLR), wave run-up, overtopping, and coastal flooding under the scenarios of 2020 to 2039. Database from tidal gauges and satellite images were used to analyze sea level rise using EEMD (Ensemble Empirical Mode Decomposition). Extreme wave condition and storm surge were estimated by numerical simulation using WWM (Wind Wave Model) and POM (Princeton Ocean Model). Coastal inundation was then simulated via WASH123D watershed model. The risk map of study areas based on the analyses of vulnerability and disaster were established using the AHP (Analytic Hierarchy Process) technique. Predictions of sea level rise, the maximum wave condition and storm surge under the scenarios of 2020 to 2039 are presented. The results indicate that the sea level at the mid-western coast of Taiwan will rise in an average of 5.8 cm, equivalent to a rising velocity of 2.8 mm/year. The analysis indicates that Wuqi, Lukang, Mailiao, and Taixi townships are susceptive, low resistant and low resilient, and reaches the high risk level. The assessment provides that important information for making adaption policy in the mid-western coast of Taiwan.

Dry intrusion is an important mid-latitude atmosphere phenomenon within the upper troposphere and lower stratosphere. It is always found to be related to the cyclogenesis, rainstorm, as well as convection generation and precipitation enhancement. Since the atmosphere environment for any of these above-mentioned weather is terribly complicated, those preexisting popular schemes which takes no account of water vapor may not suitable for detecting the dry intrusion related to these weathers. With regard to the merits and demerits of the current preexisting schemes, a new scheme based on Fengyun-2E geo-stationary satellite data is presented in this study to detect the atmospheric dry intrusion. The scheme is set up based on the statistical relationship between water vapor at high level troposphere, the general moist potential vorticity, ozone concentration and upper-level jet. After using the total amount of ozone and ozone profile operational products retrieved by Fengyun-3 Polar Orbiting Meteorological Satellites and the potential vorticity calculated by ECMWF Interim data for validation, this scheme is applied to analyze two typical middle-latitude weather processes. One is the famous Beijing extreme rainfall of 21 July 2012 and the other is a hailstorm occurred on the eastern China during March 19, 2014. A good application effect in both cases suggests that our new method of detecting dry intrusion is feasible and can be helpful in middle-latitude disastrous weather monitoring and forecasting.

The South African Weather Service (SAWS) manages an in-situ solar irradiance radiometric network of 13 stations and a very dense sunshine recording network; located in all six macro-climate zones of South Africa. A sparsely distributed radiometric network and over a landscape with dynamic climate and weather shifts is inadequate for solar energy studies and applications. Therefore, there is a need to develop mathematical models to estimate solar irradiation for a multitude of diverse climates. In this study, the annual regression coefficients, a and b, of the Ångström-Prescott (AP) model that can be used to estimate global horizontal irradiance from observed sunshine hours were calibrated and validated with observed station data. The AP regression coefficients were calibrated and validated for each of the six macro-climate zones of South Africa using the observation data that spans 2013 to 2019. The predictive effectiveness of the calibrated AP model coefficients was evaluated by comparing estimated and observed daily global horizontal irradiance. The maximum annual relative Mean Bias Error (rMBE) was 0.371 %, relative Mean Absolute Error (rMAE) was 0.745 %, relative Root Mean Square Error (rRMSE) was 0.910 % and the worst-case correlation coefficient (R2) was 0.910. The statistical validation metrics results show that there is a strong correlation and linear relation between observed and estimated solar radiation values. The AP model coefficients calculated in this study can be used with quantitative confidence in estimating daily GHI data at locations in South Africa where the daily observation sunshine duration data is available.

Objective: The aim of the study was to evaluate the influence of a suburethral sling implantation on the urge symptoms in patients suffering mixed urinary incontinence (MUI) with predominant stress component in case of. Material and methods: The study group was 220 woman with stress urinary incontinence (SUI), among them 35 women with stress-predominant MUI, treated primary with suburethral sling implantation. In 85.7% (N=30) TOT and in 14.3% (N=5) TVT was performed. The clinical symptoms and QOL were assesed before and after treatment using bladder diary and QOL questionnaire. Other additional treatment was also evaluated.Results: Subjective improvement of urge symptoms was observed in 97.1% of woman in the study group. ‘Wet OAB’ symptoms were reduced from 68.6% to 28.6% after sling procedure. Nocturia and pollakiuria were reduced from 45.7% to 11.4% and 8.6% respectively. Nocturia and pollakiuria de novo were observed in 2 (5.4%) and 1 (2.7%) patients respectively. After the sling procedure in 28.6 % (N=10) pharmacotherapy with solifenacin was administered for 2-4 months, in 8.6% (N=3) intravesical injection of botulinum toxin was performed due to persisting OAB symptoms.Conclusion: suburethral sling implantation in woman with stress- predominant MUI, although dedicated to treat SUI symptoms, seems to improve also the urge component of MUI.

This study investigated the relationship between functional movement (FM) and adiposity in adolescents (16-17 years). This research is a part of the CRO-PALS study conducted in a random sample of adolescents (n=652, mean age±SD: 16.6±0.4). Body mass index (BMI), a sum of four skinfolds (S4S), waist and hip circumference were measured, and FM was assessed via Functional Movement Screen™ (FMSTM). Multilevel analysis were employed to determine the relationship between different predictors and total FMS score. After controlling for age, moderate-to-vigorous physical activity, and socioeconomic status, relationship between variables of adiposity and total FMS score was significant and negative among boys (BMI:β=-0.18, p<0.0001; S4S:β=-0.04, p<0.0001; waist circumference:β=-0.08, p<0.0001; hip circumference:β=-0.09, p<0.0001). However, among girls, in adjusted models, only S4S showed a significant and negative effect on total FMS score (β=-0.03, p<0.0001), while other coefficients failed to reach significance (BMI:β=-0.05, p=0.23; waist circumference:β=-0.04, p=0.06; hip circumference:β=-0.01, p=0.70). Results showed that the effect of adiposity on FM in adolescence is sex-specific, suggesting that boys with overweight and obesity could be more prone to develop dysfunctional movement patterns. Therefore, exercise interventions directed toward correcting dysfunctional patterns should be sex-specific, targeting more boys with overweight and obesity rather than adolescent girls with overweight and obesity.

Data on the atmospheric gas concentrations can be received with high efficiency and on a large spatial scale only from remote laser sounding instruments. The remote laser techniques with the use of lidars are widely used in the study of the atmosphere and control of its state. The aims of this work are the design and test in numerical and field experiments of a DIAL OPO lidar system based on KTA and KTP crystals for gas analysis of the atmosphere. Lidar measurements of atmospheric gases in the near/mid infrared region have been numerically simulated. The differential absorption lidar system based on optical parametric oscillators with nonlinear KTA and KTP crystals which allow laser radiation tuning both in the near and in the middle IR spectral region is described; it allows tuning laser radiation in the near/mid-IR wavelength regions. Lidar echo signals have been experimentally recorded in the 1.8–2.5 and 3–4 m wavelength ranges. The results of H2O and CO2 profile measurements along the surface sounding path are presented.

Predictions of crop production in the Chi basin are of major importance for decision support tools in countries such as Thailand, which aim to increase domestic income and global food security by implementing the appropriate policies. This research aims to establish a predictive model for predicting crop production for an internal crop growth season prior of harvest at the province scale for fourteen provinces in Thailand's Chi basin between 2011 and 2019. We provide approaches for reducing redundant variables and multicollinearity in remotely sensed (RS) and meteorological data to avoid overfitting models using correlation analysis (CA) and variance inflation factor (VIF). Temperature condition index (TCI), normalized difference vegetation index (NDVI), land surface temperature (LSTnight), and mean temperature (Tmean) were the resulting variables in the prediction model with a p-value &lt; 0.05 and a VIF &lt; 5. The baseline data (2011–2017: June to November) were used to train four regression models, which revealed that eXtreme Gradient Boosting (XGBoost), random forest (RF), and XGBoost achieved R2 values of 0.95, 0.94, and 0.93, respectively. In addition, the testing dataset (2018–2019) displayed a minimum root mean square error (RMSE) of 0.18 ton/ha for the optimal solution by integrating variables and applying the XGBoost model. Accordingly, it is estimated that between 2020 and 2022, the total crop production in the Chi basin region would be 7.88, 7.64, and 7.72 million tons, respectively. The results demonstrated that the proposed model is proficient at greatly improving crop yield prediction accuracy when compared to a conventional regression method and that it may be deployed in different regions to assist farmers and policymakers in making more informed decisions about agricultural practices and resource allocation.

The major industrial cities of Bangladesh are heavily experiencing air pollution-related problems due to the increased trend of Particulate Matter (PM2.5) and other pollutants. This paper aimed to investigate and understand the relationship between PM2.5 and land use and climatic variables and to identify the riskiest area and population groups using a Geographic information system and regression analysis. The results show that about 41% of PM2.5 concentration increased within 19 years (2002-2021) in the study area, while the highest concentration of PM2.5 was found from 2012 to 2021. The concentrations of PM2.5 were higher over barren lands, forests, croplands, and urban areas. About 64%, 62.7%, 57%, and 55% concentrations were increased annually over barren lands, forests, cropland, and urban regions, respectively, from 2002-2021. The highest concentration level of PM2.5 (84 mg m-3) among other land use classes was found in urban areas in 2021. The regression analysis shows that air pressure (r2= - 0.26), evaporation (r2= - 0.01), humidity (r2= - 0.22), rainfall (r2= - 0.20), and water vapor (r2= - 0.03) were negatively correlated with PM2.5. On the other hand, air temperature (r2= 0.24), ground heat (r2= 0.60), and wind speed (r2= 0.34) were positively correlated with PM2.5. More than 60 Upazilas were the most polluted areas, with 1,948,029 populations (ages 0-5), 485,407 (ages 50-69), and a total population of 11,260,162 were in the high-risk/hotspot zone. The government line department may use the main results paper's key results, policymakers, stainable development practitioners, academicians, and others for integrated air pollution mitigation and management in Bangladesh and other geographical settings worldwide.

Mangroves are among the world’s most threatened ecosystems. Understanding how these ecosystems responded to past natural and anthropogenic drivers of ecological change is essential not only for understanding how extant mangroves have been shaped, but also for informing their conservation. This paper reviews the available paleoecological evidence for Pleistocene and Holocene responses of Caribbean mangroves to climatic, eustatic and anthropogenic drivers. The first records date from the Last Interglacial when global average temperatures sea levels were slightly higher than the present and mangroves grew in locations and conditions similar to today. During the Last Glaciation temperatures and sea levels were significantly lower and Caribbean mangroves grew far from their present locations, on presently submerged sites. Current mangrove configuration was progressively attained after Early Holocene warming and sea-level rise, in the absence of anthropogenic pressure. Human influence began to be important in the Mid-Late Holocene, especially during the Archaic and Ceramic cultural periods, when sea levels were already at their present position, and climatic and human drivers were the most influencing factors. During the last millennium, the most relevant drivers of ecological change have been the episodic droughts linked to the Little Ice Age and the historical developments of the last centuries.

Aedes aegypti is the main vector of various arboviruses including dengue, yellow fever, Zika and chikungunya virus. This mosquito species originated in Africa but has a wide range of distribution, colonising various ecological zones. The transmission dynamics of arboviruses depends on environmental factors, but also on mosquito life history traits including development time, fecundity, and longevity. The objective of the current study was to assess the Aedes aegypti immature development time, adult longevity, fecundity and body variation from different sampling localities. Aedes aegypti mosquitoes were collected as eggs from different geographical zones and cohorts of mosquitoes were reared in standardized laboratory conditions to assess the life history traits parameters. Emerged adults were discriminated into morphotypes according to the density of white scales on the first abdominal tergite. The means of fecundity, longevity, development time and body size were assessed, and linear models were fitted to the traits parameters to assess the effects of other covariables. Average Aedes aegypti development time was estimated to 7.35 days; 7.40 days; 6.98 days and 7.40 days respectively for Dori, 1200 logements, Bobo-Dioulasso and Toudweogo. The fecundity did not vary across study sites and was not associated with the body size. The longevity varied according to the study sites with the mosquitoes from Bobo-Dioulasso having the longest longevity while the shortest longevity was found at Dori. Fed mosquitoes had longer longevity compared to unfed ones. Morphological identification showed that Aedes aegypti aegypti-like mosquitoes were more predominant than Aedes aegypti formosus-like mosquitoes in all the study sites, suggesting the predominance of Aedes aegypti in the urban environment. Our data suggest that the geographical origin of Aedes aegypti mosquitoes in Burkina Faso has a little effect on its life history traits.

This paper presents an analysis of future precipitation patterns over the Lake Victoria Basin using bias-corrected CMIP6 model projections. A mean increase of about 5% in mean annual (ANN) and seasonal [March-May (MAM), June-August (JJA), and October-December (OND)] precipitation climatology is expected over the domain by mid-century (2040-2069). The changes intensify towards the end of the century (2070-2099) with an increase in mean precipitation of about 16% (ANN), 10% (MAM), and 18% (OND) expected, relative to the 1985-2014 baseline period. Additionally, the mean daily precipitation intensity (SDII), the maximum 5-day precipitation values (RX5Day), and the heavy precipitation events, represented by the width of the right tail distribution of precipitation (99p-90p) show an increase of 16%, 29%, and 47%, respectively, by the end of the century. The projected changes have a substantial implication for the region - which is already experiencing conflicts over water and water-related resources.

This paper argues that, in 2020, the beneficial atmospheric effect from the reduction in aviation may have been at least 7-8 times greater than that occurring from the reduction in fossil carbon dioxide emissions from all sectors. Specifically, compared to potential atmospheric effects in 2020 without the pandemic, the decrease in effective radiative forcing from reduced contrail-cirrus formation may have been in the order of 35mWm^-2 in 2020, compared to a reduction of only 4-5mWm^-2 from the drop in fossil CO₂ emissions. Over time, pursuing a low carbon pathway generates benefits that mount up to be much more significant than 2020 effects might imply, and is essential to stabilise the climate. However, a twin-track policy focus may be needed, with more emphasis on reducing short-term climate forcing, to minimise the impacts of climate change now, and to avoid detrimental feedback events. Future policy decisions about aviation should be made in this context.

The Great Barrier Reef (GBR) is currently experiencing widespread crown of thorns starfish (CoTS) outbreaks as part of the fourth wave of outbreaks since 1962. It is believed that outbreaks have become more frequent on the GBR and elsewhere in the Indo-Pacific associated with anthropogenic causes. The two widely accepted potential causes are (1) anthropogenic nutrient enrichment leading to increased biomass of phytoplankton, the food of the planktonic stage of larval CoTS; and (2) overfishing of predators on the juvenile to adult stages of CoTS, for example, commercial fished species such as coral trout. In this study, we show the evidence for the nutrient enrichment causation hypothesis is strong based on a large number of recent studies in the GBR. We also hypothesise that secondary outbreaks in the region between Cairns and Townsville can also be enhanced by nutrient enriched conditions associated with the annual nutrient discharge from Wet Tropics rivers.

Photovoltaic systems and wind energy systems are generally used in distributed system. However, zero-sequence and harmonic currents occur due to photovoltaic systems, and positive-sequence harmonic currents occur due to wind turbines. Thus, the sheath current in high voltage cables increases due to these currents and poor power quality in distributed generation plants. Metal parts of the cable are grounded to prevent the negative effects of sheath currents. When long high voltage cable lines are grounded with the method in the literature, high sheath current and voltage occur on the cable sheath. Therefore, the SSBLR method is designed as a new method for the distributed generation system. The SSBLR method has been optimized with prediction methods and multi-objective optimization methods to prevent negative effects of the sheath current. Pareto optimal method is used as multi-objective optimization method, and artificial neural network, hybrid artificial neural network and regression methods are used as prediction method. The most dominant result is searched using different estimation and optimization methods in pareto optimal method. When the artificial neural network-genetic algorithm hybrid method is used as a prediction method, and genetic algorithm used as optimization method, significant decreases are observed in sheath current and voltage.

The processing of woody biomass waste piles for use as fuel instead of burning them was investigated. At each landing slash pile location, a 132 kW grapple excavator was used to transfer the waste piles into a 522 kW horizontal grinder. Economies of scale could be expected when grinding a larger pile, although the efficiency of the loading operation might be diminished. Here, three piles were ground and the operations were time-studied: Small (20 m long × 15 m wide × 4 m high), Medium (30 × 24 × 4 m), and Large (35 × 30 × 4 m) piles. Grinding the Medium pile was found to be the most productive at 30.65 bone dry tons per productive machine hour without delay (BDT/PMH₀), thereby suggesting that there might be an optimum size of slash pile for a grinding operation. We also examined modeling of the excavator and grinder operations, and we observed that the constructed simulation model well-replicated the actual operations. Based on the modeling, we estimated that the productivity of grinding at a landing area of 710 m² of slash pile location was 31.24 BDT/PMH₀, which was the most productive rate.

Daylighting has been widely adopted in recent years due to its potential to improve the indoor environment in terms of visual comfort and energy-saving. One of the energy-saving techniques for energy-efficient buildings is the integration of louver systems. Louvers are considered more efficient for providing daylight in the interior as compared to other daylighting systems. Here, this paper presents the design of a louver system for conducting energy simulations for lighting and cooling requirements in office spaces. The simulation results indicate that the use of louvers in different opening configurations can lead to energy savings, particularly in the lighting aspect. The louver system in office spaces with a 50% louver opening leads to 27.0% energy savings. Further, the results are presented for different louver openings to calculate the lighting and cooling energy savings. The overall performance of the system is better in terms of providing consistent daylight, which eventually improves energy saving.

Heart failure (HF) diagnosis, phenotyping, prognosis, and treatment decisions are all based on the left ventricular ejection fraction (EF). Heart failure with mid-range EF (HFmrEF) is a third EF category for heart failure with an EF between 40 and 49 percent. Comparatively, heart failure with preserved EF or reduced EF has been largely unexplored. 10–25% of patients with HF have HFmrEF. Although HFmrEF has an intermediate clinical profile, it is more similar to HF with reduced EF, particularly because these patients have a high incidence of ischaemic heart disease. Heart failure with preserved EF has a lower risk of cardiovascular events than heart failure with reduced EF, which is milder. HFmrEF and HF with preserved EF patients have a similar or higher risk of non-cardiovascular adverse events than patients with HF with reduced EF. There is still a great deal of mystery surrounding HFmrEF. The purpose of this review is to describe the major pathophysiology of HFmrEF and its similarities and differences with the other two types of EF. It is the purpose of this paper to present a comprehensive overview of the currently available evidence in support of the pathophysiology of patients with HFmrEF. Further investigation of the pathophysiology, treatment, and prognosis of this condition will be needed in the future in order to better understand it.

Abstract: The Tropical Rainfall Measuring Mission (TRMM) and then Global Precipitation Mission (GPM) are the most important and widely used data sources in the forecasting of drought, flood, and water resources management. However, since this sensor’s data is primarily used for tropical regions, it is necessary to evaluate the accuracy for optimal use of the data across varying climatic and physiographic conditions. In this study, the accuracy of the satellite data for a span of 17 years (2000-2017) for three climatic zones has been explored using synoptic ground station data. The climates include a) arid and low rainfall, b) semi-arid and low rainfall, and c) humid and high rainfall. We evaluated satellite data accuracy in drought and wet conditions based on the Standard Precipitation Index (S.P.I.) and different seasons. For available ground control stations, 13 stations were used in the humid, seven stations in a semi-arid climate, and 12 stations in the dry climate. The results show that the monthly precipitation product of GPM (IMERG product) and TRMM (TMPA/3B43 product) overestimate the rainfall. In the arid climate, the precipitation is estimated 43%, in the semi-arid environment 50%, and in the humid weather 11% more than the ground-based data on average. Therefore, to use satellite data in different climates, it is necessary to make corrections to obtain precise results. Based on 32 ground stations, the correction coefficient has a positive relationship with average precipitation and altitude and an inverse relationship with the latitude. Further in-depth investigations showed that the accuracy of satellite data in wet conditions is higher than the accuracy of normal circumstances, and the accuracy of normal conditions is more accurate than drought conditions. Besides, the accuracy of satellite data in wet or dry conditions increases with increasing time scales. The highest accuracy was obtained for a 12-month time scale and the lowest accuracy for the 3-month time scale of drought conditions in the arid climate.

Commercially available multispectral and thermal imagers are commonly deployed for environmental monitoring on small uncrewed aerial systems (sUAS, <55 lbs). Our team assessed the challenges of deploying these imagers on a Group 3 classification UAS (weight: 55-1320 lbs, maximum altitude: 18,000 ft MSL, maximum speed: 250 kts) for the purpose of land-atmosphere interaction studies. A Micasense Altum multispectral imager was deployed on two very similar mid-sized (Group 3) UAS, a Mississippi State University (MSU) TigerShark XP and the Department of Energy (DOE) ArcticShark. This paper examines the effects of flight on imaging systems mounted on UASs flying at higher altitudes, faster speeds, and for longer duration, which near future technology will make more the norm. For these platforms we found that the acquisition rate may need to be higher to achieve a minimum 75% overlap, as required by certain post-processing algorithms. Additionally pre-flight calibration panel referencing was found to be problematic for converting flight images to reflectance, due to the changing illumination conditions during the extended duration flights. We developed an automated workflow to correct the image frames via data from an onboard hemispherical solar sensor mounted on the top of the airframe, and we assessed these data against known spectral ground targets and independent sources. Finally, this manuscript may be used as a reference for collecting similar datasets in the future. The datasets described within this manuscript may be used as a starting point for future research.

The purpose of this work is to study quasi-stationary wave structure in the mid-latitude stratosphere and mesosphere (40–50°N) and its role in the formation of the annual ozone cycle. Geopotential height and ozone from Aura MLS data are used and winter climatology for January–February 2011–2020 is considered. More closely examined is the 10-degree longitude segment centered on Longfengshan Brewer station, China, and located in the region of the Aleutian Low influence associated with the quasi-stationary zonal maximum of total ozone. Annual and semi-annual oscillations in ozone were compared using units of ozone volume mixing ratio and concentration, as well as changes in ozone peak altitude and in time series of ozone at individual pressure levels between 316 hPa (9 km) and 0.001 hPa (96 km). The ozone maximum in the vertical profile is higher in volume mixing ratio (VMR) values than in concentration by about 15 km (5 km) in the stratosphere (mesosphere), in consistency with some previous studies. We found that the properties of the annual cycle are better resolved in the altitude range of the main ozone maximum: middle–upper stratosphere in VMR and lower stratosphere in concentration. Both approaches reveal SAO/AO-related changes in the of ozone peak altitudes in a range of 4–6 km during the year. In the lower-stratospheric ozone of the Longfengshan domain, an earlier development of the annual cycle takes place with a maximum in February and a minimum in August compared to spring and autumn, respectively, in zonal means. This is presumably due to the higher rate of dynamical ozone accumulation in the region of the quasi-stationary zonal ozone maximum. The “no-annual-cycle” transition layers are found in the stratosphere and mesosphere. These layers with undisturbed ozone volume mixing ratio throughout the year are of interest for more detailed future study.

The wind industry is looking for ways to accurately predict the reliability and availability of newly installed wind turbines. Failure modes, effects and criticality analysis (FMECA) is a technique utilized for determining the critical subsystems of wind turbines. There are several studies which applied FMECA for wind turbines in the literature, but no studies so far have considered different weather conditions or climatic regions. Furthermore, various design types of wind turbines have been analyzed applying FMECA but no study so far has applied FMECA to compare the reliability of geared and direct-drive wind turbines. We propose to fill these gaps by using Koppen-Geiger climatic regions and two different turbine models of direct-drive and geared-drive concepts. A case study is applied on German wind farms utilizing the WMEP database which contains wind turbine failure data from 1989 to 2008. This proposed methodology increases the accuracy of reliability and availability predictions and compares different wind turbine design types and eliminates underestimation of impacts of different weather conditions.

In the early decades of the 19th century, the deaf population in the eastern US and Canada was distributed across a vast area. After the 1817 founding of the American School for the Deaf (ASD) in Hartford, CT and the subsequent establishment of schools for the deaf in New York City (NYSD), Philadelphia, and many other US states, hundreds of deaf students called these schools home for several years. After leaving school, the early American Deaf community faced a challenge: How would the community maintain its social and linguistic ties across a vast geographical area once community members had dispersed to their hometowns? In this paper we analyze the attendance registries of two large gatherings of deaf individuals in Hartford in the years 1850 and 1854. These were among the largest and earliest known gatherings of deaf adults. The demographic data included in these registries open a window onto the evolving American Deaf community of the mid-19th century. Our analyses of the attendees’ school affiliations, ages, and marital status show that the signing community that had taken root among students at schools in Hartford and New York persisted among the adult graduates of those schools in towns across the northeastern US. We compare the places of residence of ASD and NYSD alumni in 1850 and 1854 to their hometowns when they first enrolled at school. Our comparisons suggest the mid-19th-century signing community had become more urban; it was centered to a greater extent in populous cities such as New York, Boston, and Hartford than had been true when the attendees had enrolled in school. We consider how the geography of deafness in the 19th century might inform our understanding of the sources of regional variation in ASL. We also consider how early cross-regional interactions may have inhibited such regional variation.

Identifying a panel of markers detecting kidney injury before the glomerular filtration rate (GFR) reduction is the challenge to improve the diagnosis and the management of acute kidney injury (AKI) in septic patients. This study evaluated the roles of tissue inhibitor metal proteinase, insulin growth factor binding protein (TIMP2*IGFBP7), and mid-regional pro-adrenomedullin (MR-proADM) in AKI patients. Patients and Methods: This study was prospectively conducted in the Intensive Care Unit (ICU) enrolling 230 patients who underwent cardiac surgery. Biomarkers were evaluated before and after 4 hours of the cardiac surgery. Results: Whereas urine and creatinine alterations appeared at 23.2 (12.7 – 36.5) hours, after cardiac surgery, urinary TIMP2*IGBP7 levels were higher at 4 hours in AKI patients (1.1±0.4 mg/l vs 0.08±0.02 mg/l; p < 0.001). Its concentration >2 mg/l increases the AKI risk within the following 24 hours, clearly identifying the population at high risk of renal replacement therapy (RRT). In patients with sepsis, MR-proADM levels were 2.3 nmol/l (0.7–7.8 nmol/l), with the highest values observed in septic shock [5.6 nmol/l (3.2–18 nmol/l)] and a better diagnostic profile than procalcitonin and C-reactive protein to identify septic patients. MR-proADM values >5.1 nmol/l and urine TIMP2*IGBP7 levels > 2 mg/l showed a significantly faster progression to RRT, with a mean follow-up time of 1.1 days. Conclusions: TIMP2*IGBP7 and MR-proADM precociously diagnose AKI in septic patients after cardiac surgery, giving prognostic information for RRT requirement.

Conventional mechanical Fourier Transform Spectrometers (FTS) are able to simultaneously measure absorption and dispersion spectra of gas-phase samples. However, they usually need very long measurement times to achieve time-resolved spectra with a good spectral and temporal resolution. Here, we present a mid-infrared dual-comb-based FTS in an asymmetric configuration, providing broadband absorption and dispersion spectra with a spectral resolution of 5 GHz, a temporal resolution of 20 μs, and a total measurement time of a few minutes. We used the dual-comb spectrometer to monitor the reaction dynamics of methane and ethane in an electrical plasma discharge. We observed ethane/methane formation as a recombination reaction of hydrocarbon radicals in the discharge in various static and dynamic conditions. The results demonstrate a new analytical approach for measuring fast molecular absorption and dispersion changes and monitoring fast dynamics of chemical reactions, which can be interesting for chemical kinetic research and particularly for the combustion and plasma analysis community.

Spatiotemporal climate variability is a leading environmental constraint to the rain-fed agricultural productivity and food security of communities in the Abbay basin and elsewhere in Ethiopia. The previous one-size-fits-all approach to soil and water management technology targeting did not effectively address climate-induced risks to rain-fed agriculture. This study, therefore, delineates homogenous climatic regions and identifies climate-induced risks to rain-fed agriculture that are important to guide decisions and selection of site-specific technologies for green water management in the Abbay basin. The k-means spatial clustering method was employed to identify homogenous climatic regions in the study area, while the Elbow method was used to determine an optimum number of the climate clusters. The k-mean clustering used the Enhancing National Climate Services (ENACTS) daily rainfall, minimum and maximum temperatures, and other derived climate variables that include daily rainfall amount, length of growing period (LGP), rainfall onset and cessation dates, and rainfall intensity, temperature, potential evapotranspiration (PET), soil moisture and AsterDEM to define climate regions. Accordingly, 12 climate clusters or regions were identified and mapped for the basin. Clustering a given geographic region into homogenous climate classes is useful to accurately identify and target locally relevant green water management technologies to effectively address local-scale climate-induced risks. The study has also provides a methodological framework that can be used in the other river basins of Ethiopia and indeed elsewhere.

Understanding how climatic variables impact the reference evapotranspiration (ET0) is essential for water resource management, especially considering potential fluctuations due to climate change. Therefore, we used the Sobol method to analyze the spatiotemporal variations of Penman-Monteith ETo sensitivity to the climatic variables: downward solar radiation, relative humidity, maximum and minimum air temperature, and wind speed. The Sobol’s indices variances were estimated by Monte Carlo integration, setting the sample limits to 2.5 and 97.5 percentiles of the daily data of 33 automatic weather stations located in the state of Mato Grosso, Brazil. The results of the Sobol analysis indicate considerable spatiotemporal variations in the sensitivity of ETo to climatic variables and their interactions. The dominant climatic variable responsible for ET0 fluctuations in Mato Grosso is incident solar radiation, which has a more significant impact in humid environments, as observed in the areas of the Amazon biome in the state. Air relative humidity and wind speed have higher sensitivity indices during the dry season in the areas of the Cerrado biome (Savanna) in Mato Grosso. Our findings show that changes in solar radiation, relative humidity, and wind speed cannot be ignored when analyzing changes in reference evapotranspiration.

This study aims to suggest a basis for the selection of technologies for developing high-performance buildings to reduce energy consumptions and greenhouse gas emissions. Energy-saving technologies comprising of 15 cases were categorized into passive, active, and renewable energy systems. EnergyPlus v8.8 was used to analyze the contribution of each technology in reducing the primary energy consumptions and CO₂ emissions in the Korean climate. The primary energy consumptions of the base model were 464.1 and 485.1 kWh/m²a in the Incheon and Jeju, respectively, and the CO₂ emissions were 83.4 and 87.4 kgCO₂/m²a, respectively. Each technology (cases 1–15) provided different energy-saving contributions in the Korean climate depending on their characteristics. The heating, cooling, and other energy-saving contributions of each technology indicate that their saving rates can be used when selecting suitable technologies during the cooling and heating seasons. Case 15 (active chilled beam with dedicated outdoor air system + ground source heat pump) showed the highest energy saving rate. In case 15, the Incheon and Jeju models were reduced by 189.4 (59.2%) and 206.2 kWh/m²a (57.4%) compared to the base case, respectively, and the CO₂ emissions were reduced by up to 32.7 (60.8%) and 35.6 kgCO₂/m²a (59.3%), respectively.

Thailand has formulated her climate change policy and updated relevant plans and policies to align with the goal of achieving carbon neutrality and net zero GHG emissions. This study investigates the optimal level of GHG mitigation in Thailand, taking into account the marginal abatement cost (MAC) and social cost of carbon (SCC). It evaluates how energy efficiency and renewable energy technologies influence GHG reduction in the power and industrial sector and illustrates policy recommendations that align with the 2020 to 2050 policy and plan period. The findings indicate that there may be instances where GHG mitigation potential is insufficient to reach the national mile-stone. In such cases, it becomes imperative to leverage all technologies within the marginal abatement cost curve (MACC) and also utilization of the social cost of carbon for policy decision making and meeting the desired goals. In certain scenarios, the adoption of additional technologies or measures may be necessary, such as flexible power generation and deploying carbon capture and storage or hydrogen which are high-cost technologies. Furthermore, preparations should be made for multiple levels of climate change policies and plans beyond 2030.

Accurate estimations of actual evapotranspiration (ETa) are fundamental for various environmental issues. Artificial Intelligence-based models are considered a promising alternative to the most common direct ETa estimation techniques and indirect methods by remote sensing (RS)-based surface energy balance models. Artificial Neural Networks (ANN) are proven to be suitable for predicting reference evapotranspiration and ETa based on RS data. The aim of this study is to develop a methodology based on ANNs for estimating daily ETa values using NDVI and land surface temperature, coupled with limited site-specific climatic variables at a large irrigation catchment. Two scenarios were implemented by the ANN model. Data from only the 38 days of satellite overpass dates was selected in Scenario-I, while the 769-day data included the satellite overpass dates and other days located between two satellite overpass acquisitions in Scenario-II. An irrigation scheme in the Mediterranean region of Turkiye was selected, and a total of 38 Landsat images, and local climatic data were used in 2021 and 2022. Results showed that R2 values in Scenario-I and II were acknowledgeably high for training (0.79 and 0.86), testing (0.75 and 0.81), and the entire dataset (0.76 and 0.84), respectively. Results of the new model in two scenarios showed acceptable agreement with ETa-METRIC values. The proposed ANN model demonstrated the potential of obtaining daily ETa using limited climatic data and RS imagery.

Over the last 20 years, begomoviruses have emerged as devastating pathogens, limiting the production of different crops worldwide. Weather conditions increase vector populations, with negative effects on crop production. In this work we evaluated the relationship between the in-cidence of begomovirus and climatic conditions before and during the crop cycle. Soybean and bean fields from the northwest (NW) of Argentina were monitored for 14 years and classified as moderate (≤50%) and severe (> 50%) according to the relative incidence. Two hundred bio-meteorological variables were constructed, summarizing meteorological data in 10-day peri-ods from June to March of each crop year. The studied variables included temperature, precipi-tation, relative humidity, wind (speed and direction), pressure, cloudiness and visibility. For bean, high maximum winter temperatures, low spring humidity and precipitation 10 days before planting correlated with severe incidence. In soybeans, high late winter and pre-planting tem-peratures, and low spring precipitations were found to be good predictors of high incidence of begomovirus presence. The results suggest that temperature and pre-sowing precipitations can be used to predict incidence status [predictive accuracy: 82% (bean) and 75% (soybean)]. Thus, these variables can be incorporated in early warning systems for crop management deci-sion-making to reduce the virus impact on bean and soybean crops.

Climate change is expected to increase the occurrence of droughts with the hydrology in alpine systems being largely determined by snow dynamics. In this paper we propose a methodology to assess the impact of climate change on both meteorological and hydrological droughts taking into account the dynamics of the snow cover area (SCA). We will also analyse the correlation between these types of droughts. We have generated ensembles of local climate scenarios based on regional climate models (RCMs) representative of potential future conditions. We have considered several sources of uncertainty: different historical climate databases, simulations obtained with several RCMs, and some statistical downscaling techniques. We then used a stochastic weather generator (SWG) to generate multiple climatic series preserving the characteristics of the ensemble scenario. These were simulated within a cellular automata (CA) model to generate multiple SCA future series. They were used to calculate multiple series of meteorological drought indices, the Standardized Precipitation Index (SPI) and Standardized Precipitation Evapotranspiration Index (SPEI)) and a novel hydrological drought index (Standardized Snow Cover Index (SSCI)). A linear correlation analysis was applied to both types of drought to analyse how they propagate and the time delay between them. We applied the proposed methodology to the Sierra Nevada (southern Spain) where we estimated a general increase in meteorological and hydrological drought magnitude and duration for the horizon 2071-2100 under the RCP 8.5 emission scenario. The SCA droughts also revealed a significant increase in drought intensity. The meteorological drought propagation to SCA droughts is reflected in an immediate or short time (1 month), obtaining significant correlations in lower accumulation periods of drought indices (3 and 6 months). This will allow us to obtain information about meteorological drought from SCA deficits and vice versa.

Liver is structurally organized into zonation where LSECs endothelial cells play a crucial role during chronic liver injury and early stages of fibrosis. Fibrosis can be reversed if diagnosed early at molecular level in zonation before progressing to advanced stages like bridging fibrosis. This study identified zonation marker genes using scRNA-seq and spatial transcriptomics molecular profiling technologies in normal and diseased fibrotic human liver. DGE analysis is performed over LSECs and identified the top 20 expressed genes in periportal, perivenous, and intermediate acinar zones. Multi-omics and scRNA-seq analysis over Visium images and ECs liver cells figured out OIT3, DNASE1L3, CLEC4G, LYVE1, FCN2, CRHBP as commonly expressed mid-lobular zonation-specific genes. Also, this study detected STAB2, F8, AQP1, TEK, TIMP3, TIE1, CTSL genes as expressed in DILI and NASH ECs populations. The connection between LSECs marker genes in zone 2 and liver fibrosis holds significant promise for advancing our understanding in developing new therapeutic strategies for fibrosis reversal and designing computational molecular biomarkers in NASH and DILI fibrotic liver diseases.

Copper-nitride (Cu3N) semiconductor material is attracting much attention as a potential, next-generation thin-film solar-light absorber in solar cells. In this communication, polycrystalline Cu3N thin films were prepared using reactive-RF-magnetron-sputtering deposition, at room temperature, onto glass and silicon substrates. The very-broadband optical properties of the Cu3N thin film layers were studied by UV-MIR (0.2-40 μm) ellipsometry and optical transmission, to be able to achieve the goal of a low-cost absorber material to replace the conventional silicon. The reactive-RF-sputtered Cu3N films were also investigated by focused ion beam scanning electron microscopy, and both FTIR and Raman spectroscopies.

According to the Cosmological Principle the Universe is isotropic and no preferred direction would be seen by an observer that might be stationary with respect to the expanding cosmic fluid. However, because of observer’s partaking in the solar system peculiar motion, there would appear in some of the observed properties of the Cosmos a dipole anisotropy, which could in turn be exploited to determine the peculiar motion of the solar system. The dipole anisotropy in the Cosmic Microwave Background Radiation (CMBR) has given a peculiar velocity vector 370 km s−1 along l=264∘,b=48∘. However, some other dipoles, for instance, from the number counts, sky brightness or redshift distributions in large samples of distant Active Galactic Nuclei (AGNs), have yielded values of the peculiar velocity many times larger than that from the CMBR, though surprisingly, in all cases the directions agreed with the CMBR dipole. Here we determine our peculiar motion from a sample of 0.28 million AGNs, selected from the Mid Infra Red Active Galactic Nuclei (MIRAGN) sample comprising more than a million sources. From this, we find a peculiar velocity, which is more than four times the CMBR value, although the direction seems to be within ∼2σ of the CMBR dipole. A genuine value of the solar peculiar velocity should be the same irrespective of the data or the technique employed to estimate it. Therefore, such discordant dipole amplitudes, might mean that the explanation for these dipoles, including that of the CMBR, might in fact be something else. But, the observed fact that the direction in all cases, is the same, though obtained from completely independent surveys using different instruments and techniques, by different sets of people employing different computing routines, might nonetheless indicate that these dipoles are not merely due to some systematics, otherwise why would they all be pointing along the same direction. It might instead suggest a preferred direction in the Universe, implying a genuine anisotropy, which would violate the Cosmological Principle, the core of the modern cosmology.

Maize (Zea mays L.) is the most widely grown important crop in mid altitude areas of intensive maize-based cropping system of western Ethiopia. Agronomic management is the most important input for getting potential yield and high net returns in hybrid maize production. A field experiment was carried out on farmers’ field to find out the effect of varieties (four maize) and nitrogen fertilizer rate (55, 110 kg N ha-1) with one control on yield components and nitrogen use efficiency of different maize varieties in 2013 and 2014 cropping season. It was laid with randomized complete block design in factorial arrangement with three replications. Mean grain yield, thousand seed weight, dry biomass and harvest index of maize varieties were significantly differed among farms and varieties of maize. Application of nitrogen fertilizer rates was significantly increased mean grain yield maize varieties. Interaction of maize varieties with nitrogen fertilizer rates was significantly affected all yield components of maize varieties. Application half and full recommended nitrogen fertilizer gave mean grain yield advantages of 31 and 41 % over control maize varieties planted without nitrogen application. Maize varieties producing higher mean grain yield was also giving higher mean dry biomass. Mean nitrogen up take was varied from 225 to 357 kg ha-1 among varieties of maize. Higher agronomic efficiency of all maize varieties was obtained from maize planted with application half recommended nitrogen fertilizer compared to full recommend. Agronomic efficiency was ranged from 18 to 33 produced among maize varieties. Significantly higher nitrogen up take efficiency of maize varieties was achieved from maize planted with full recommended nitrogen fertilizer application. Considerably higher nitrogen use efficiency of maize varieties was realized from all maize varieties planted with application half recommended nitrogen fertilizer. Application of half recommended nitrogen fertilizer was gave 32 % fertilizer N use efficiency advantage as compared to full recommended nitrogen fertilizer. Maize varieties BH-661>BH-660> BH-543>BH-540>BH-140 were desirable varieties for further promotion work and use by smallholder farmers in mid altitude area of western Ethiopia.

The current communication presents the application of a consolidated model combination strategy to analyze the medium-term carbon fluxes in two Mediterranean pine wood ecosystems. The modelling strategy is based on the use of a NDVI-driven parametric model, Modified C-Fix, and of a bio-geochemical model, BIOME-BGC, the outputs of which are combined taking into account the actual development phase of each ecosystem. The two pine ecosystems examined correspond to an old-growth forest and to a secondary succession after clearcuts, which differently respond to the same climatic condition during a ten-year period (2013-2022). Increasing dryness, in fact, exerts a fundamental role in controlling the gross primary and net ecosystem production of the mature stand, while the effect of forest regeneration is prevalent for the uprising of the same variables in the other stand. In particular, the simulated net carbon exchange fluctuates around 200 g C m-2 year-1 in the first stand and rises to over 600 g C m-2 year-1 in the second stand; correspondingly, the accumulation of new biomass is nearly undetectable in the former case while becomes notable in the latter. The study therefore supports the potential of the applied strategy for predicting the forest carbon balances consequent on diversified natural and human-induced factors.

The reduction of biodiversity loss is one of the targets of the 2030 Agenda for Sustainable Development. The protection of endangered species is critical for conserving global biodiversity. Asian elephants，as one of the last few mega-herbivores on Earth, are currently threatened by climate changes and anthropogenic modifications. The modelling of their living habitats is of top priority to the conservation of Asian elephant. In this study, we used the maximum entropy model (MaxEnt) to identify the current and potential future habitats of Asian elephants in South and Southeast Asia. We performed analyses for future projections with 17 scenarios by using the present results as baseline. To optimise the modelling results, we delineated the core habitats by using the Core Mapper Tool and compared them with existing protected areas (PAs) through gap analysis. The results showed that the current total area of core habitats is 491,455 km2 in size and will be reduced to 332,544 km2 by 2090 under SSP585 (the shared socioeconomic pathway). The projection analysis under differential scenarios suggested that most of the core habitats in the current protected areas would remain stable and suitable for elephants in the future. However, the remaining 75.17% of the core habitats lay outside the current PAs, and finally we mapped approximately 219,545 km2 of suitable habitats as priority protected areas in the future. Although our model did not perform well in some regions, our analyses and findings still could provide useful references to the planning of protected areas and conservation of Asian elephant.

Building more energy efficient and sustainable urban areas that will both mitigate the effect of climate change and adapt for the future climate, requires the development new tools and methods that can help urban planners, architect and communities achieve this goal. In the current study, we designed a workflow that links different methodologies developed separately, to derive the energy consumption of a university school campus for the future. Three different scenarios for typical future years (2039, 2069, 2099) were run as well as a renovation scenario (Minergie-P). We analyse the impact of climate change on the heating and cooling demand of the buildings and determined the relevance of the accounting of the local climate in this particular context. The results from the simulations showed that in the future there will a constant decrease in the heating demand while for the cooling demand there will be a significant increase. It was further demonstrated that when the local climate was taken into account there was an even higher rise in the cooling demand but also that the proposed renovations were not sufficient to design resilient buildings. We then discuss the implication of this work on the simulation of building energy consumption at the neighbourhood scale and the impact of future local climate on energy system design. We finally give a few perspective regarding improved urban design and possible pathways for the future urban areas.