The rheological properties of a polyamide (PA) resin with low crystallinity were modified by melt-mixing it with a small amount of an alternative a-olefin–maleic anhydride copolymer as a reactive compound. Because PA has a low melting point, rheological characterization was performed over a wide temperature range. Owing to the reaction between PA and the alternative a-olefin–maleic anhydride copolymer, the blend sample behaved as a long-chain branched polymer in the molten state. The thermo-rheological complexity was obvious owing to large flow activation energy values in the low modulus region. The primary normal stress difference under steady shear was greatly increased in the wide shear rate range, leading to a large swell ratio at capillary extrusion. Furthermore, strain hardening in the transient elongational viscosity, which is responsible for favorable processability, was clear. Because this is a simple modification method, it will be widely employed to modify the rheological properties of various polyamide resins.

The presented work offers a novel process scheme for valorizing historical Pb-Zn slag, which involves crushing, grinding, and then using separation techniques to concentrate valuable components (nonferrous metals). This methodology could have a significant impact on the global beneficiation of metallurgical slags since, in theory, it is significantly more simple, environmentally friendly, and cost-effective than standard pyrometallurgical or hydrometallurgical procedures. According to previous physicochemical and mineralogical studies, Pb-Zn slag from "Topilnica" Veles is a valuable secondary raw material. This inhomogeneous technogenic resource contains substantial amounts of nonferrous metals (Pb, Zn, Cu, and Ag). However, laboratory tests have indicated that the Pb-Zn slag contains a very uneven valuable metals amounts, ranging from several g/ton to several tens of g/ton. The main issue is that traditional metallurgical procedures for releasing beneficial elements are not commercially viable since the valuable elements are "trapped" within amorphous aluminosilicates or intergrowths of alloy grains and glassy phases. Gravity concentration (Wilfley 13 shaking table) and magnetic separation (Davis separator and disk separator) were used to obtain the final concentrate following comminution and grindability testing. The gravity concentration proved more effective. This streamlined approach of valorizing Pb-Zn slag can reduce the need for hazardous chemicals used in hydrometallurgical refinement operations, as well as the extremely high temperatures required for pyrometallurgical processing. This is the first investigation into the feasibility of this novel approach, which includes direct investigations of the Pb-Zn slag feed using these alternative technologies. After extracting the valuable metals, the amorphous aluminosilicate part of the Pb-Zn slag can be reapplied as an alternative raw material in the building sector, adding to the circularity of the suggested approach..

This study explores novel techniques to improve the detection accuracy of skarn iron deposits using advanced image processing methodologies. Leveraging the capabilities of Aster image, Band Ratio (BR) images, and Principal Component Analysis (PCA), alongside the power of 3D Convolutional Neural Networks (3D-CNN), the research aims to enhance the precision and efficiency of ore detection in complex geological environments. The proposed method employs a specific 3D-CNN architecture, accepting input as a 7×7×C image patch, where C represents the combined number of selected Aster image bands, Principal Component (PC) bands, and computed BR images. To evaluate the accuracy of the proposed method, five distinct image bands combinations, including the proposed bands combination, were tested and evaluated based on the overall accuracy (OA), average accuracy (AA), and kappa coefficient. The results demonstrated that while the incorporation of BR images alongside Aster bands initially seemed promising, it introduced significant confusion in certain classifications, leading to unexpected mis-classification rates. Surprisingly, utilizing solely Aster bands as input parameters yielded higher accuracy rates (OA= 93.13%, AA = 91.96%, Kappa = 90.91%) compared to scenarios involving the integration with band ratios (OA = 87.02%, AA = 79.15, and Kappa = 82.60%) or the integration of BR images to PC bands (OA= 87.78%, AA = 82.39%, Kappa = 83.81%). However, the amalgamation of Aster bands with selected PC bands showed slight improvements in accuracy (OA= 94.65%, AA = 92.93%, Kappa = 93.45%), although challenges in accurately classifying certain features persisted. Ultimately, the proposed combination of Aster bands, PC bands, and BR images (proposed bands combination) presented the most visually appealing and statistically accurate results (OA = 96.95%, AA= 94.87%, and Kappa = 95.93%), effectively addressing misclassifications observed in the other combinations. These findings underscore the synergistic contributions of each of the Aster bands, PC bands, and BR images, with Aster bands proving pivotal for optimal skarn classification, PC bands enhancing intrusions classification accuracy, and BR images strengthening wall rock classification accuracy. In conclusion, the proposed combination of input image bands emerges as a robust and comprehensive methodology, demonstrating unparalleled accuracy in the remote sensing detection of skarn iron minerals.

Due to the high impact of the building sector on the environment, a growing interest focuses on insulating materials able to ensure good thermo-acoustic performance for the building envelope, in a sustainable and circular economy perspective. In this context, Moroccan natural gypsum was mixed with natural waste local materials. Thermal and acoustic properties of the samples were measured; they were compared to those of synthetic- and mineral-based gypsum plasters, manufactured with the same technique. A Small Hot Box apparatus was used for thermal characterization, whereas acoustic performance was investigated by means of a Kundt’s Tube. Natural and synthetic additives involved a reduction in density and an improvement in thermal performance. Conductivity values in the 0.181 – 0.238 W/mK range were obtained, depending on the type of natural additive, with respect to 0.275 – 0.323 W/mK of mineral-based gypsum plasters. The acoustic measurements showed that all the composites have similar performance in terms of acoustic absorption, whereas high Transmission Loss values were obtained for the natural additives (TL = 35 – 59 dB). Petiol of Palm and Stipa Tenacissima were found as the materials able to improve both thermal and acoustic properties.

The article presents the results of studies aimed to identify the effect of foliar treatments of winter wheat, sugar beets and soybeans with mineral and bioorganic fertilizers. Their positive effect on increasing the concentration of mineral forms of nitrogen in soil was revealed. The crop types have a greater influence on the size of nitrous oxide emissions: in winter wheat crops - 679 µg/m3, soybeans - 637.2 µg/m3, sugar beets - 576.8 µg/m3. The amounts of nitrous oxide emissions were lower in the variants without the use of phosphorus-potassium fertilizers. The Ruter AA fertilizer showed the greatest efficiency on winter wheat crops - 42.7 c/ha. Soybean grain yield of 44.2 c/ha was also achieved by using Ruter AA, as well as Geo-humate together with phosphorus-potassium fertilizers. On the background of the actual supply of phosphorus and potassium, maximum yield was obtained when using N30 on the leaf - 39.3 c/ha. Foliar feeding ensured a yield of sugar beet root crops of up to 67.1-77.4 c/ha on the backdrop of the application of phosphorus-potassium fertilizers with the advantage of using Amino turbo. The largest yield of sugar beet roots without use of mineral phosphorus and potassium was ensured by N30 treatment of the leaf in the phases of 4-6 and 8 leaves - 63.2 t/ha. Of the organo-mineral fertilizers and biostimulants, the best result was shown by the use of Ruter A - 62.6 t/ha. We believe that foliar feeding of crops can be a sustainable farming method that can increase crop yields and reduce N2O emissions.

Ruminant animals naturally emit methane gas owing to anaerobic microbial fermentation in the rumen, and these gases are considered major contributors to global warming. Scientists worldwide are attempting to minimize methane emissions from ruminant animals. Some of these attempts include the manipulation of rumen microbes using antibiotics, synthetic chemicals, dietary interventions, probiotics, propionate enhancers, stimulation of acetogens, manipulation of rumination time, vaccination, and genetic selection of animals that produce low methane (CH4). The majority of synthetic additives are harmful to both beneficial rumen microbes and the host or only temporarily affect methanogenesis. Phytogenic feed additives (PFAs) have recently emerged as the best alternatives to antibiotics and synthetic chemicals because of growing public concerns regarding drug resistance and the negative impacts of antibiotics and synthetic chemicals on humans, livestock, and the environment. These additives reduce methane production and improve the volatile fatty acid profile. In this review, we provide an overview of PFA sources and how their bioactive components affect the rumen microbiome to reduce methane emissions. Additionally, we highlight the mechanisms of action of PFAs as a whole as well as some of their bioactive components.

Composite fiber materials are superior materials due to their high strength and light weight. Composites reflect the properties of their constituents, which is proportional to the volume fraction of each phase. There are different fiber reinforcement types and each affects it’s flexural, tensile and compression strength. When selecting a composite for a specific application, the forces excreted on the composite must be known in order to determine the reinforcement type. Unidirectional fiber reinforcement will allow very strong load resistance but only in one direction where as a random orientated fiber reinforcement can resist less load but can maintain this quota in all directions. These materials are said to be anisotropic. Certain composite fibers, taking into consideration there weights, are physically stronger than conventional metals. This research deals with the analysis of three composite materials with different reinforcement types, volume fraction and phase content. It was found that material A (glass epoxy) was the strongest in the longitudinal direction with a flexural strength of 534 MPa in the longitudinal and 420 MPa in the transverse direction. The flexural stresses of material B (glass silicone) and material C (glass polyester) where both found in the 120 to 135 MPa range. Differences were due to their differences in matrix composition and reinforcement type.

The article focuses on mining of non-energy mineral resources with minimum environmental impacts. It issues from research results of a project Competence Centre for Effective and Ecological Mining of Mineral Resources implemented at the Faculty of Mining and Geology at VŠB-Technical University of Ostrava, Czech Geological Survey, a company Watrad ltd., a state enterprise Diamo, a company RPS Ostrava plc and a company Sedlecký kaolin plc. The paper starts with a partial analysis of the existing legal norms related to mining and processing of mineral resources. Next, it analyses mineral resource mining options free of negative environmental impacts. The fundamental tool to assess potential environmental impacts of mining is the implementation of Environmental Impact Assessment (EIA) process for a given mineral resource. In the Czech Republic environmental impact assessment is carried out by course of Act 100/2001 Coll. Its important amendment is Act 39/2015 Coll. claiming, inter alia, that the environmental impact assessment is rigidly connected with other permits and procedures, such as the zoning process and building construction permits. The article describes the environmental impacts of mining of non-energy mineral resources, including the following factors: appropriation of land, impacts on surface water, ground water and soil, noise, influence on the landscape character, and air pollution. The paper also includes a case study summarizing information on the environmental factors that may play a role in potential underground mining of graphite in the deposit Český Krumlov - Městský Vrch and the deposit Lazec - Křenov.

The relationship between the structure characteristics and performances of coal based hydrogenation isomeric base oil (CTL) and metallocene catalyzed coal based polyalphaolefin (mPAO) base oil was clarified here. CTL and mPAO were compared with typical petroleum based and natural gas based commercial API Class III and IV base oils. Pressurized differential scanning calorimetry (PDSC), Rotary Bomb Oxidation Test (RBOT) and four-balls friction tester were used to evaluate the oxidation stability and lubrication performance of base oils under different working conditions. The sensitivity of different base oils to typical antioxidants and extreme pressure antiwear agents was compared. Specially, the composition and structure of CTL base oil are obviously different from GTL and mineral base oil. The coal-based CTL and mPAO base oils exhibit commendable viscosity-temperature properties, characteristics, coupled with low-temperature fluidity, fire safety, and minimal evaporation loss. The lubricating properties, oxidation stability and the sensitivity to extreme pressure antiwear agents of CTL are close to those of similar base oils. But the sensitivity of CTL to typical antioxidants is relatively poor. Besides, compared with commercial PAO base oil, mPAO has lower isomerization degree and fewer isomerization types. The oxidation stability and sensitivity to typical antioxidants of mPAO base oil are comparable with those of commercial PAO base oil, while its lubrication performance and sensitivity to typical extreme pressure antiwear agents are significantly better than those of commercial PAO base oil.

In this study, the determination of static E50 and υ parameters of rock materials was investigated using P-S wave velocities and Shore hardness (SH), non-destructive measurement methods. We used multiple linear regression (MLR), multiple non-linear regression (MNLR) and artificial neural network (ANN) models to estimate and determine these parameters. When the models defined by MLR, MNLR, and ANN were compared to the R2 values, ANN models that estimate E50 and υ parameters of rock materials using non-destructive methods (Vp, Vs, Vp/Vs, d, and SH) could be determined with higher accuracy than MLR and MNLR models. The study’s originality is based on the fact that ores such as galena, chromite, and barite have been studied for the first time on rock mechanics, and in this respect, it offers an innovative perspective. In addition, the use of all non-destructive measurement methods, Vp, Vs, and Shore hardness tests, also increases the originality of the study.

Despite its growing importance as a dry beneficiation method, there is a lack of studies exploring the fundamentals aspects of dry jigging. In this sense, this study focuses on explore some essential aspects of density-based separation in dry jigs, like pulse profile, energy consumption and, especially, stratification over time, also exploring an innovative operational strategy here called “transient pulsation”. The tests were carried out using density tracers distributed across 11 density ranges (0.4-2.4 g/cm³) and employing a base bed (gravel) to analyze their segregation in a pilot-scale dry jig. Pressure drop and active power data were acquired to measure the pulse characteristics and energy consumption. The findings suggest that establishing the dry jigging cycle is more complex than in hydraulic jigs due to the compressibility of air. Stationary pulsation tests revealed an unstable behavior of stratification over time, contrasting with traditional hydraulic jigs, while transient pulsation tests unveiled varied trends in separation quality. Energy consumption analysis underscored the significant role of the blower drive. These insights have the potential to inform operational enhancements in dry jigging.

The aim of this work is to compare two softwares (MAUD and TOPAS) based on the Rietveld algorithm and to test the concept of tolerance factor using the dissolution at high temperature of yttrium into BaTiO₃. In general, both softwares give up different values of the crystalline parameters however the trends are similar in most cases but the analysis of the strain and crystallite size in the BaTiO₃ crystals suggests that, in this particular case, MAUD offered results more consistent with the expected behavior. Using the crystalline parameters calculated by Rietveld, the tolerance factor values were obtained and these data suggest even better stability in the crystalline structure than that expected using theoretical parameters. Tolerance factor concept also indicates that Ti⁴⁺ should be preferred.

This work shows the physicochemical and mineralogical characterization of diatomites form the Hidalgo and Jalisco States, Mexico. In the case of the mineral from Hidalgo State, this has the following chemical composition; 70.0 % wt. SiO₂, 11.63 wt. % Al₂O₃, 1.95 wt. % FeO, 1.79 wt. % MgO, 2.41 wt. % K₂O, 0.85 wt. % CaO and 6.10 wt. % Na₂O. On the other hand, the mineral from Jalisco has the following chemical composition; 93.58 wt. % SiO₂, 3.03 wt. % Al₂O₃, 1.81 wt. % FeO, 0.40 wt. % MgO, 0.92 wt. % K₂O, 0.11 wt. % CaO and 0.24 wt. % Na₂O. For recovery of metals, both minerals got arsenic, silver, lead and nickel recoveries upper to 95 % and lower to 10 % for chromium. According to efficiency of interchange, the mineral from Hidalgo is slightly higher in the case of arsenic, lead and silver; while for nickel and particularly chromium (VI) the efficiency is higher for the mineral from Jalisco.

Establishment of protected areas (PAs) is one of the key global conservation strategies that currently cover approximately 15% of the earth’s land surface. Globally, PA networks are designed to curb the growing anthropogenic pressures in areas with high biological diversity. Despite the importance of PAs in conserving the vanishing biodiversity and unique habitats, many of them are in critical condition due to poor governance thus functioning below the expected level. Moreover, in many developing countries, the PA coverage is below the global standard. Recognizing their contemporary role in conservation, governments have recently agreed to expand the global PA coverage to 17% by the year 2020 (Aichi target 11). This book with eight chapters from different regions of the world provides an overview of the PAs governance, institutional mechanisms, conservation benefits, limitations and challenges associated with their respective policy discourse, integrated management, and functional attributes. Protected areas expect to to play an important role in the long rn in conservation and protection of biodiversity and ecosystems particularly in countries where population pressure and habitat loss are high. Regular intervention, political commitment, and effective governance are essential for the sustainability of PAs across the world. Here, we also attempted to shed some light on future development clues for the sustainable management and monitoring of PAs worldwide.

The article presents the results of research work devoted to the study of composite materials on polymer binder with the content of modified mineral filler - water-dispersion paint and varnish materials on acrylic polymer with modified filler - diatomite. The aim of the study is to obtain polymer-based composites with modified diatomite (water-dispersion paint on acrylic binder) with improved performance properties. Methods: determination of porosity, adhesion, elasticity, hiding power of the control composition; determination of porosity, adhesion, elasticity, hiding power of the obtained composites with the use of modified filler; investigation of the influence of radiation in the infrared radiation (IR) region of the spectrum of the paint coating surface using FLIRB620 thermal imager. As a result of work it is noticed that modification of water dispersions by silica activated diatomite promotes elimination of the main disadvantages of materials and coatings on the basis of acrylate binder - low water resistance and low physical and mechanical characteristics, introduction of modified diatomite into water emulsion paint on acrylate basis does not lead to deterioration of the main operational characteristics of paint and varnish coatings - porosity, adhesion, elasticity and covering. When analyzing the effect of emissivity in the IR region of the spectrum of the paint coating surface, a significant effect of the quantitative content of modified diatomite on the reduction of emissivity of paint coatings in the IR region of the spectrum was established and it was shown that a significant effect of the reduction of emissivity of paint coatings in the IR region of the spectrum is provided by the introduction of modified diatomite in the amount of 40 wt.h. into the mixture. The influence of the time of full-scale tests in the investigated small range regardless of the quantitative composition of modified diatomite on the performance characteristics of the paintwork was established.

By repeated unloading and loading of the excavation dynamic and static loads, repeated train dynamic and static loads of multi-factors, the underpass tunnel, cross tunnel engineering influence area rock layer, the existing tunnel structure of the three constitutes a multifaceted structure, multi-factor interaction system. Existing tunnels into the prediction theory model of the new tunnel excavation process of dynamic and static loads, dynamic and static loads of existing tunnels are mostly analyzed individually, the results of synergistic analysis needs to be improved. Based on the theory of the current layer method, the paper comprehensively considers the stiffness of the existing tunnel, the stiffness of the new tunnel, the excavation method load and the existing tunnel load, coupled with Peck's empirical formula, the theoretical model of deformation prediction for excavation of a two-lane highway tunnel under the tunnel through the existing railroad is proposed, and verified and optimized by numerical calculations and monitoring data, which proves the applicability and reliability of the theoretical model in the similar strata and the project promotion.

The petrogenesis and geodynamic implications of the early Paleozoic adakitic rocks in the east of Inner Mongolia remain topics of debate. In this study, petrology, zircon U–Pb age and Lu–Hf isotopic composition, whole-rock geochemistry and Sr–Nd isotopes from adakitic rocks. Zircon U–Pb dating results demonstrate that the formation age is 242.8±1.0Ma, 247Ma，which is the product of Early Triassic magmatism. Petrology and geochemical study have shown that the granodiorite have high SiO2 (66.93% ~69.40%), Al2O3(15.37% ~ 15.43%), MgO (1.35% ~1.55%), with LREE enrichment and HREE deficit，and they have high Sr, low Y. and high Sr/Y ratios, showing typical signatures of adakitic rocks. The εHf(t) values of zircon vary between +11.3 and +13.8, with a low whole-rock (87Sr/86Sr)i ( 0.703382 )and positive εNd(t) values, the average Mg# of the rock is 56.14, suggesting that adakite derived from partial melting of MORB, and magma interaction with the mantle. Comprehensive analysis suggests that during the Late Permian to Early Triassic, the subducted slab of the Paleo-Asian Ocean broke off, and the residual oceanic slab preserved in the mantle beneath the subduction zone underwent partial melting, generating adakitic magma.

Deep learning has increasingly been employed to identify minerals. However, deep learning can only be used to identify minerals in the distribution of the training set, while any mineral outside the spectrum of the training set is inevitably categorized erroneously within a predetermined class from the training set. To solve this problem, the study introduces the approach that amalgamates One-Class Support Vector Machines (OCSVM) with the ResNet architecture for the out-of-distribution mineral detection. Initially, ResNet undergoes training using a training set comprising well-defined minerals. Subsequently, the earlier layers of the trained ResNet are employed to extract the discriminative features of the mineral under consideration. These extracted mineral features then become the input for OCSVM. When OCSVM discerns the mineral in the training set's distribution, it triggers the subsequent layers within the trained ResNet, facilitating the accurate classification of the mineral into one of the predefined categories encompassing the known minerals. In the event OCSVM identifies the mineral out of the training set's distribution, it is unequivocally categorized as an unclassified or 'unknown' mineral. Empirical results substantiate the method's capability to identify out-of-distribution minerals while concurrently maintaining a commendably high accuracy rate for the classification of the 36 in-distribution minerals.

Solid waste management in Accra is a major challenge to the Metropolitan Authorities and inhabitants. The rapidly increasing population coupled with poor capacity of the municipal and private waste management companies to management waste effectively has created issues of environmental concern. Due to poor waste managements systems, most household dispose waste indiscriminately leading to floods and health issues. The study showed that about 60% of household waste is organic materials which has the potential to be converted to compost for agriculture purpose. Meanwhile plastics and rubbers which litters the environment as well as blocking major storm drains and gutters hence creating huge environmental hazard is made of 11% of the total component of most household waste generated daily. The study also revealed that among the methods of disposing waste, dumping waste in skip containers located at authorized places was the preferred means of disposing waste by household though others also dispose waste by other means such as burying and burning. Inadequate skip containers per population of household in an area coupled with irregularity of tracks picking these containers makes skip containers dumping site ugly scene, hence creating health issues. Among the constraints that impact negatively on sustainable waste management in Accra Metropolis, economic constraints was perceived as the main challenge which affect efficient waste management. Currently the country is going through serious economic challenges so government does not release money timely to fund projects which waste management is key. Most donor partners that use to support the government with funds have either reduced or redrawn their services as they have no confidence in the state of Ghana economy. Aside the constrains, the study also indicated that factors such as poor public attitude towards waste management, poor enforcement of sanitation by-laws, inadequate and untimely release of government funds were also seen as the main factors affecting waste management.

Crop rotation diversification using legumes has been advocated as one of the solutions to improve the resilience of the crop system to various environmental stresses and the use of nitrogen resources. However, when forage legumes or grass-legumes are ploughed, there is a high risk of nitrate leaching, especially in sandy soils. The aim of the study was to determine the effect strip tillage intercropping management on soil mineral nitrogen (SMN), water-extractable organic carbon (WEOC) content and winter wheat (WW, Triticum aestivum L.) grain yield compared to forage legume and WW monocropping with conventional tillage. In intercropping was used winter wheat - black medick (Medicago lupulina L.) WW+BM, winter wheat - white clover (Trifolium repens L.) WW+WC, and winter wheat - Egyptian clover (Trifolium alexandrinum L.) WW+EC. Research was repeated in two experiments. The results showed that after strip tillage and WW sowing less or similar SMN content cud be detected, as in conventional tillage and WW + forage legumes intercropping. WW grain yield in intercrops decreased, compared to the grasses monocultures that were ploughed before WW sowing. The highest amount of WEOC was in intercropping soil growing WW+WC or in all fields (except WW+EC) after applying strip tillage. During the research period, the amounts of mobile humic substances (HSs) and mobile humic acids (HAs) changed analogously. Their content increased substantially in fields with WC and EC, regardless of whether the grasses were ploughed or grown with WW.

Biosolids from stabilized sludge presents a high fertilization potential due to its rich content of nutrients and organic matter. Three formulas of organo-mineral fertilizers based on biosolids were manufactured having at least 2 % N, 2 % P2O5, and 2 % K2O and characterized by classical and advanced methods. The content of N and P in the final formula was measured using specific reactants combined with VIS-nearIR spectroscopy. Additionally, all three formulas were characterized by advanced 1H NMR relaxometry, double-quantum and FT-IR spectroscopy. Structural characterization was performed using SEM, EDX and X-ray diffraction. Four dynamical components were identified in the T2-distribution showing that the rigid component is into a percentage larger than 90 %. In order to evaluate the release properties of organo-mineral fertilizers dynamic measurements of electric conductivity and pH were performed, by placing 0.25 g of formulas (V1, V2 and V3) in 200 ml of distillate water. It was found that V3 present the smallest release velocity, but release the largest amount of fertilizers. Two release mechanisms were also observed.

Good governance in natural resource management (NRM) is one of the most challenging issues in developing countries that often inappropriately embedded in national policies and political agendas. It is, in fact, even more important for countries like Bangladesh with exceptionally high pressure and dependence on its natural resources for sustaining rural livelihoods. Globally, nowadays, good governance is considered as one of the key factor for achieving the goal of sustainable development and biodiversity conservation. Bangladesh, of late has responded to that global zeal by involving local communities in the management of country’s declining forest and other natural resources. The colonial legacy of the forestry sector of Bangladesh was planned and, managed as interim projects through donors’ prescriptions. Thus, institutions, management processes and conservation outcomes were problematic. The conventional approach adopted by colonial and post-colonial regimes for forest management also proved to be inefficient due to its top-down management system. The absolute dependency on donor support, and their prescription sometimes worsened the situation both ecologically and socially. Global, regional and local trends supported the need for a different dimension in the governance paradigms. The introduction of a pluralistic approach, known as co-management in protected areas (PAs) is an example of an attempt whereby shared governance mechanism are implemented to attain the desired goals of conservation that will also address the livelihoods and aspirations of communities living in and around PAs of the country. However, in designing future forest and PA regimes the concern of the external aid support and attached conditions remain a reality that needs to be addressed. Adequate attention should be given to our vanishing biodiversity, culture and community livelihoods through devising an appropriate governance mechanism recognizing and supporting local rights, access and participation in the environmental management. It is now time to mainstream the adhoc nature of governance according to our national conservation strategy and policy frameworks in order to achieve the goals and objectives of the Bangladesh NRM sector addressing the human and community right of people in the specific context of forest protected areas management.

Biodiversity has become an issue of global anxiety over the past decades due to its rapid decline worldwide. Bangladesh as one of the most densely populated countries in the world is no more exception. The country, although, was once very rich in biodiversity, during the last few decades as a consequence of the rapid reduction in forest area, urbanisation, habitat modification, unsustainable natural resources use and collection and overall climate change it has decreased alarmingly. Of late, the government, as a signatory of various regional and international conservation treaties, has taken various initiatives to improve country’s dwindling biodiversity. This paper reviews the present situation of biodiversity in Bangladesh, management trends and major causes of biodiversity loss. A separate statutory body is fundamental to ensure conservation, sustainable use and equitable sharing of benefits arisen from biodiversity in the country.

Despite of being an exceptionally biodiversity rich country, the forest coverage of Bangladesh is declining at an alarming rate. Declaration and management of protected areas in this regard is one of the efforts from government side to tackle the loss of biodiversity. The limited numbers of forest-protected areas (FPA), established to conserve the dwindling forest biodiversity of the country with high pressure on them for timber, non-timber forest products, and fuelwood - makes their management challenging. Moreover, most of the FPAs of the country declared only in the recent decades with very limited infrastructure, manpower and policy support for monitoring and governance. Some people-centred approaches for the management of FPAs and alternative livelihood and income generation subsidies although made available through a few project interventions, their number are still inadequate and performance remains less than satisfactory. This chapter provides a critical review of the FPAs of Bangladesh looking at their role in biodiversity conservation, management challenges, and key lessons from previous management interventions with recommendations for the future. It has been revealed that the FPA system of Bangladesh still poorly represents the diverse forest ecosystems with relatively small forest size and lack of corridors for the movement of wildlife. There are ample opportunities to render co-management of FPAs an effective strategy to minimize the conflicts in FPAs management in the country. It is, however, important to ensure the access of local forest-dependent people to different alternative income generating options that may adequately support their livelihoods.

Microplastics are widespread in freshwater environments and could impact these ecosystems. Bivalves are freshwater organisms that are particularly exposed to microplastic contamination. Therefore, in this preliminary study, the accumulation of microplastics, plasticizers, and additives in the freshwater bivalves Anodonta cygnea through active biomonitoring was investigated. Specimens commercially bought were exposed in three rivers in Central Italy for different exposure times: short (1 month) and long (3 months). The gills and the gastrointestinal tract (GIT) were analyzed separately to evaluate the possible uptake and ingestion of particles via Micro-FTIR. For the first time, small microplastics (SMPs, 5-100 µm), plasticizers, additives, and other micro-litter components, e.g., natural and non-plastic synthetic fibers (APFs) were identified in the bivalve A. cygnea. The most abundant polymer in the gills (94.4%), and GITs (66.1%) was polyamide, which had the highest concentration in each river. A decrease in SMPs' abundance was observed over time in the gills in each river, while the abundance in GIT increased. Compared to polymers, a greater variety of APFs was observed in rivers. The APFs changed during the time of exposure and between different rivers more evidently than polymers, allowing a clearer identification of the possible sources. These results highlighted plastic pollution by SMPs using freshwater bivalves as sentinel organisms and the need to investigate further the additives that can be proxies of the presence of microplastics in the environment and biota.

Gut bacteria play an important role in several metabolic processes and human diseases, such as obesity and its co-morbidities, like fatty liver disease, insulin resistance/diabetes and cardiovascular events. Among several factors, dietary patterns, probiotics, prebiotics, synbiotics, antimicrobials and non-dietary factors, such as stress, age, exercise and climatic conditions, can dramatically impact the human gut microbiota diversity and equilibrium. However, the effect of minor food constituents, including food additives and trace contaminants, on human gut microbiota has received less attention. Consequently, the present review aimed to provide an objective perspective of the current knowledge regarding the impacts of minor food constituents on human gut microbiota and consequently, on human health.

In this study, nano-diamond (ND) and MoS2 powder are used as additives in a carbonyl iron based magnetorheological fluid (MRF) to improve its tribological performance. MRFs are prepared by dispersing 35 wt.% of CI particles in silicone oil, and adding different proportions (0, 1, 3 or 5 wt.%) of ND and MoS2 additives. Seven kinds of MRFs are made and tested using reciprocating friction and wear tester under different normal loads, and then the friction characteristics are evaluated through analyzing experiment results. The morphology properties of MRFs and contacting surfaces before and after tests are also observed using a scanning electron microscope and analyzed by energy-dispersive X-ray spectroscopy. The results show that the appropriate weight percentage of MoS2 additives may decrease friction coefficient and wear zone. It is also demonstrated from the detailed analyses of worn surfaces that the wear mechanism is influenced not only by additives but also by applied normal load and magnetic field strength.

Jade waste is a normal byproduct that makes up much more than the amount of jade extracted. Therefore, recycling jade waste is worth investigating from the point of view of energy conservation. Moreover, it is an environment-friendly material, which is desirable for use in building materials. In this study, Xiuyan jade waste was repurposed as antibacterial additives for building coatings. The powder waste was activated by milling and subsequent annealing. The antibacterial properties of the treated waste were mostly related to the annealing temperatures. Based on the investigations of the phase change and the release of metal ions of a series of samples and their antibacterial activities, the antibacterial mechanism of the treated samples was explored experimentally. The most applicable sample for coatings was finally chosen by considering its pH values and its antibacterial abilities. Antibacterial testing showed that the addition of treated jade waste could enhance the bacterial inhibition rate of building coatings from 60% to 99.9%.

Field studies were conducted in 2016, 2017, and 2020 in south-central and the Coastal Bend regions of Texas to determine the effects of various biostimulants and soil additives on corn growth and yield. In south-central Texas, the use of pop-up fertilizer (9-30-0 + Zn) either alone or in combination with either 2% N, bifenthrin, or bifenthrin + pyraclostrobin resulted in the greatest corn vigor but a yield response was only noted with pop-up fertilizer alone at 28062 or 46771 ml ha-1 in one year. In the Coastal Bend region, leaf tissue analysis showed that only Fe was affected with the use of any soil additive. Bacillus licheniformis + bacillus megaterium + bacillus pumilus increased Fe leaf tissue content by 20% over the untreated check. Radicoat seed coating at 438 ml ha-1 reduced corn plant stand by 10% and Pseudomonas brassicaceanum reduced corn height when compared with the untreated check; however, no differences in test weight or yield from the untreated check were noted with any soil additive. Little if any impacts of the use of biostimulants or soil amendments were seen in these studies.

Environmental nanoparticles have been shown to exist in most aquatic environments, and environmental nanoparticles in water distribution systems significantly affect water quality. However, little research has been conducted on the environmental nanoparticles in mineral water, which is a special water resource. Nanoparticle tracking analysis (NTA) and high-resolution transmission electron microscopy (HRTEM) were conducted. This study was the first to identify many environmental nanoparticles in natural mineral water in Zibo City, Shandong Province, China. The results of the NTA showed that the concentration of the particles was 5.5 ×106 particles/mL and the peak diameter of the size distribution was 180 nm. The HRTEM showed that the nanoparticles were granular, pinniform, rodlike, and flakey in shape, and some of the nanoparticles existed in aggregation. The energy-dispersive spectrometry results showed that most of the nanoparticles contained O, Mg, Ca, Si, Fe, Ti, and P, and some of them also contained F, V, S, and Mn. When combined with the characteristics of the selected area electron diffraction pattern, the nanoparticles were confirmed to be Ca-bearing nanoparticles, attapulgite nanorods, MnO2 nanosheets, and TiO2 nanoparticles. These results indicate a new form of elements occurring in mineral water. In addition, based on the chemical and physical characteristics of the nanoparticles and mineral water, these environmental nanoparticles in the mineral water are likely to be the weathering byproducts of minerals. These nanoparticles within mineral water provide a good opportunity for understanding the behavior of nanoparticles in varied systems. Moreover, environmental nanoparticle science is important for continuing efforts in water safety, treatment, and remediation.

The growing interest in modern polymer materials targeted the research on complex plastic coatings and the possibilities of modifying their features and properties during manufacturing. Today's modern coatings, including polyurea and polyurethane, are among the most modern developed resins. Compared to other polymer coatings, they are distinguished by their versatility, strength, and durability. They undoubtedly represent the next step in the evolution of coatings. Advances in coating technology have also led to the development of spray, injection, and roto-cast application equipment, improving polyurea-based elastomers’ performance. For many years, there has been much interest in increasing the flame resistance of polymers. This is dictated by safety considerations and the increasing requirements for the flammability of plastics, the area of application of which is growing every year. This text attempts to provide an overview of current research on flame retardant composites. Particular attention was paid to polyurea (PU) and polyurea-based hybrids and the application areas of polyurea coatings. The paper defines flame retardants, discusses how they work, and presents types of flame retardants and the current trends of their usage in the production of plastics.

An inter- and transdisciplinary concept has been developed, focusing on the scaling of industrial circular construction using innovative compacted mineral mixtures (CMM) derived from various soil types (sand, silt, clay) and recycled mineral waste. The concept aims to accelerate the systemic transformation of the construction industry towards carbon neutrality by promoting the large-scale adoption and automation of CMM-based construction materials, which incorporate natural mineral components and recycled aggregates or industrial by-products. In close collaboration with international and domestic stakeholders in the construction sector, the concept explores the integration of various CMM-based construction methods for producing wall elements in conventional building construction. Leveraging a digital urban mining platform, the concept aims to standardize the production process and enable mass-scale production. The ultimate goal is to fully harness the potential of automated CMM-based wall elements as a fast, competitive, emission-free, and recyclable alternative to traditional masonry and concrete construction techniques. To achieve this objective, the concept draws upon the latest advances in soil mechanics, rheology, and automation and incorporates open-source digital platform technologies to enhance data accessibility, processing, and knowledge acquisition. This will bolster confidence in CMM-based technologies and facilitate their widespread adoption. The extraordinary transfer potential of this approach necessitates both basic and applied research. As such, the proposed transformative, inter- and transdisciplinary concept will be conducted and synthesized using a comprehensive, holistic, and transfer-oriented methodology.

We describe a vision for a national-scale heavy mineral (HM) map generated through automated mineralogical identification and quantification of HMs contained in floodplain sediments from large catchments covering most of Australia. The composition of the sediments reflects the dominant rock types in each catchment, with the generally resistant HMs largely preserving the mineralogical fingerprint of their host protoliths through the weathering-transport-deposition cycle. Heavy mineral presence/absence, absolute and relative abundance, and co-occurrence are metrics useful to map, discover and interpret catchment lithotype(s), geodynamic setting, magmatism, metamorphic grade, alteration or mineralization. Underpinning this vision is a pilot project, focusing on a subset of the national sediment sample archive, which is used to demonstrate the feasibility of the larger, national-scale project. We preview a bespoke, cloud-based mineral network analysis (MNA) tool to visualize, explore and discover relationships between HMs as well as between them and geological setting or mineral deposits. We envisage that the Heavy Mineral Map of Australia and MNA tool will contribute significantly to mineral prospectivity analysis and modeling here, particularly for technology critical elements and their host minerals, which are central to the global economy transitioning to a more sustainable, decarbonized paradigm.

Wetting of the surface area of an electrode materials as complete as possible is desirable to achieve optimum specific capacity of an electrode material. Keeping this surface area utilized even at high current densities and even when inside of pores is required for high capacitance reten¬tion. The addition of surfactants at very small concentration to aqueous supercapacitor electro¬lyte solutions has been suggested as a way to improved performance in terms of capacitance, ca¬pacitance retention at increased current density and higher stability. Effects are pronounced with car¬bon materials used in electro-chemical double layer capacitors, they are also observed with re¬dox materials. Causes of the observed improvements and mode of operation of the added surfac¬tants seem to need further investigations; they are inconclusive beyond the obvious statement of in¬creased wetting. Reported examples and the current state of understanding are reviewed.

Thermal shape memory polymers (SMPs) find increasing applications in biology and medicine due to their promising potential for improved biocompatibility. In such applications, the inevitable penetration of small molecules from the ambient fluid into the polymer influences the shape recovery process and often leads to a reduction of the temperature, at which shape recovery takes place. We show here via molecular dynamics simulations that the size of additive molecules plays a key role for this process. While the effect of concentration on the recovery rate is monotonic in the investigated range, a non-monotonic dependence on the size of additive molecules emerges at temperatures close to the glass transition. This work thus identifies the additives’ size to be a qualitatively novel parameter for switching the recovery process in polymer-based shape memory materials.

In-situ grown C_0.3N_0.7Ti and SiC, which derived from non-oxide additives Ti₃SiC₂, are proposed to densify silicon nitride (Si₃N₄) ceramics with enhanced mechanical performance. Remarkable increase of density from 79.20% to 95.48% could be achieved for Si₃N₄ ceramics with 5vol% Ti₃SiC₂. The capillarity of decomposed Si from Ti₃SiC₂, and in-situ reaction between nonstoichiometric TiC_x and Si₃N₄ were believed to be responsible for densification of Si₃N₄ ceramics. An obvious enhancement of flexural strength and fracture toughness for Ti₃SiC₂ doped Si₃N₄ ceramics was observed. The maximum flexural strength of 795 MPa for Si₃N₄ composites with 5vol% Ti₃SiC₂ and maximum fracture toughness of 6.97 MPa^.m^1/2 for Si₃N₄ composites with 20vol% Ti₃SiC₂ are achieved when mixed powders are hot-press sintered at 1700℃. Pull out of elongated Si₃N₄ grains, crack bridging, crack branching and crack deflection were demonstrated to dominate enhance fracture toughness of Si₃N₄ composites.

In recent years, intelligent identification and prediction of ore deposits based on deep learning algorithm and image processing technology has gradually become one of the research frontiers in the field of geological and metallogenic prediction. However, this method also has many problems that need to be solved. For example, (1) very few trainable image samples containing mineral point labels; (2) The geological image features are small and irregular, and the image similarity is high; (3) It is difficult to calculate the influence of different geological prospecting factors on ore mineralization. Based on this, this paper constructs a deep learning network model Multiscale Feature Attention Framework (MFAF) based on geo-image data. The results show that MFCA-Net module in MFAF model can solve the problem of scarce mine label images to a certain extent. In addition, the channel attention mechanism SE-Net module can quantify the difference of influence of different source factors on mineralization. The prediction map is obtained by applying the MFAF model in the study of deposit identification and prediction in the research area of the southern section of Qin-hang metallogenic Belt. In the forecast map, many regions have high metallogenic potential. Through observation, it is found that the above predicted area covers 100% of the known ore deposits at present, which has a good prediction effect. Later, we can find out the specific reasons through field verification. The multi-scale feature fusion and attention mechanism MFA Framework in this paper can provide a new way of thinking for geologists in mineral exploration. The research of this paper also provides resource guarantee and technical support for the sustainable exploitation of mineral resources and the sustainable growth of society and economy.

This paper deals with experimental study of the influence of conductive (Fe₃O₄) and insulating (Al₂O₃) nanostructured particles at various concentrations on the dielectric strength of transformer mineral oil. The method of preparation and characterization of these nanofluids (NFs) through the measurements of zeta potential, the real and imaginary parts of dielectric constant as well as the concentration and size of nanoparticles using Scanning Electron Microscope (SEM) images of nanoparticles powders and Dispersive x-ray Spectroscopy (EDS) analysis are presented. Experimental findings reveal that these two types of nanoparticles materials significantly improve AC breakdown voltage and the magnitude of this improvement depends on the concentration, size and nature (material) of nanoparticles. For a given type of nanoparticles, the effect is more marked with the smallest nanoparticles. The conductive nanoparticles offer higher enhancement of dielectric strength compared with insulating nanoparticles based nanofluids. With Fe₃O₄, the breakdown voltage (BDV) can exceed twice that of mineral oil and it increases by more than 76% with Al₂O₃. The physicochemical mechanisms implicated in this improvement are discussed.

In recent years, technical processes for the sequestration of CO2 through industrial waste mineral carbonation have been explored and developed. There is a large portfolio of Carbon Capture, Uti-lisation and Storage (CCUS) techniques that have been employed on a laboratory and at pilot scale. These include geological storage, ocean storage and mineralisation by carbonate ores. In view of this, the main purpose of this research was to investigate and explore chemical variables, particularly ammonium salts as lixiviants for calcium mineral extraction from iron making slag. The slag in use was acquired from a Steel Mill in the Vaal Triangle Region in Gauteng, South Af-rica. The experimental test work was conducted using different ammonium lixiviants, namely, NH4NO3, NH4Cl and CH3COONH4 to understand the influence of anion type as well as possible differences in mechanisms of interactions. Lixiviant concentration as well as the reaction time were varied in this research study. The three selected ammonium based lixiviants showed different extents of calcium extraction owing to differences in the anion groups. NH4NO3, NH4Cl and CH3COONH4 were found capable of dissolving 50% to 80% of calcium from the selected slag for different molar concentrations. Anion type and leaching time also had significant influences on the leaching of calcium from the slag. Rapid pH degradation resulted in better calcium extraction ca-pabilities. This work has shown that the selected ammonium salts have a potential as lixiviants for calcium dissolution from iron making blast furnace slags. These lixiviants would therefore be important to consider during calcium mineral carbonation for CO2 sequestration.

Water-soluble nonionic surfactant, pentaethylene glycol monododecyl ether, C12E5, spontaneously blooms to the surface of spin-cast hydrophobic polyiso-prenes, generating hydrophilic surfaces. This system represents a simple model for hydrophilic chemical modification of rubbery polymers yet demonstrates surprisingly rich, complex and unexpected behaviour. The ver-tical depth profiles were quantified using neutron reflectometry (NR) and deuterated surfactant, and the surface properties were characterized using con-tact angle analysis and atomic force microscopy (AFM). Despite the low surface tension of the toluene solvent used in film preparation and the low surface en-ergy of the PI matrix, NR depth profiles revealed clear evidence of surfactant segregation. This surface layer was typically thicker than a monolayer, but incomplete, yet was remarkably stable with respect to dissolution, even when exposed to hundreds of thousands of times the volume of water required to dissolve all the surfactant on the surface. Despite the apparent resistance to removal from the surface, water exposure does alter the subsequent wettabil-ity of the surface, with a hydrophilic-to-hydrophobic transition occurring after rinsing. Complementary AFM images of these C12E5 / cis-PI films showed unexpected strand-like features on the surface of the film, which we attribute to a non-uniform lateral distribution of some of the surfactant. This surface structure becomes more evident after rinsing, and it appears that there are two distinct populations of surfactant on the PI film surface. We conclude that some of the bloomed surfactant exists as layers, which are relatively inert with respect to rinsing or surface modification, and some is laterally inhomogene-ous. This latter population is primarily responsible for surface wetting be-havior, but is not detected by specular NR.

Until recently, the classic approach to mineral exploration studies is to bring the field samples/drill cores collected during field studies to the laboratory followed by laborious analysis procedures to generate the analytical data. This is very expensive, time consuming and difficult for exploring vast areas. But rapid technological advances in field portable analytical instruments such as portable ultraviolet–visible and near-infrared spectrophotometers, gamma ray spectrometer, pXRF, pXRD, pLIBS, and µRaman spectrometer have changed this scenario completely and increased their on-site applications in mineral exploration studies. These instruments are currently providing direct, rapid, on-site, real-time, non-destructive, cost-effective identification, and determination of target elements, indicator minerals and pathfinder elements in rock, soil, and sediment samples. These portable analytical instruments are currently helping to obtain accurate chemical and mineralogical information directly in field with minimal or no sample preparation, and providing decision-making support during field work as well as during drilling operations in several successful mineral exploration programs. In this article, the developments in these portable devices, and their contributions in the platinum group elements (PGE), rare earth elements (REE), gold, base metals, and lithium exploration studies both on land and on ocean bed have been summarized with examples.

Mineral identification is an important part of geological analysis. Traditional identification methods rely on either the experiences of the appraisers or the various measuring instruments and the methods are either easily influenced by the experiences or need too much work. To solve the above problems, there have been studies using image recognition and intelligent algorithms to identify minerals. But the current studies can not identify many minerals, and the accuracy is low. To increase the number of identified mineral categories and the accuracy, we proposed the method that uses both the mineral images and the Mohs hardness in the deep neural networks to identify the minerals. The experimental results showed that the method can reach 94.0% Top-1 accuracy and 99.9% Top-5 accuracy for 28 common minerals. The model that combines image and Mohs hardness together can identify more minerals and increase the accuracy using less training data.

Dietary supplements are more and more often used to increase daily intake of essential vitamins and minerals. These preparations are classified as special category of foods and are subject to food law, not pharmaceutical regulations. As a result the requirements to dietary supplements are much less restrictive than to medications. Also simple and inexpensive procedure of registration causes that the number of dietary supplements is widely spread every year. On every manufacturing phases of dietary supplements, there is a risk of contamination. One of the pollutions might be mercury which is classified as heavy metal. Its inorganic compounds damage kidneys and liver and methylmercury is easily absorbed from gastrointestinal system. Methylmercury is distributed in all tissues, also in nervous system. The aim of study was to determine the level of mercury in multivitamins and multiminerals preparations and to analyze the results. The study included 22 dietary supplements containing vitamins and minerals available on Polish market. Mercury was analyzed with atomic absorption spectrometry using AMA 254. The concentrations of Hg was 0.22–5.85 µg/kg (the average content was 2.40 µg/kg). The highest average mercury content was 4.51 µg/kg, whereas the lowest one was 0.31 µg/kg. The results was also analyzed in individual groups depending on main component and indication for use as well as pharmaceutical formulation. Also according to manufacturer’s recommendation, the dose of mercury taken with a single medicine was estimated for time of a day, a week, a month, 3 months and also a year. The findings were compared to limits defined in regulations of European Union and PTWI set by JECFA to assess the health risk. The results presented in this study proved that the amount of mercury in tested dietary supplements is much lower than the value of valid regulations. Analyzed supplements as long as they are used with the recommendation of manufacturer, do not pose a threat to human health.

The article presents the results of research on the production of effective inorganic fillers and chemically resistant composite polymer-mineral materials based on industrial waste. The aim of the work is to develop the technological foundations for the production of inorganic fillers and highly filled filling compositions for use in chlorine-containing media. Materials with high resistance to hydrochloric acid are graphite and quartz sand. Thermal power plant (TPP) ash was used as an acid-resistant filler in the compositions. The simplex lattice planning method was used to determine the areas of compositions with the best properties. Two components were selected: formaldehyde rubber resin and mineral filler (TPP ash) as a binder. As the third component, hydrolytically active fillers were used - anhydrite, phosphogypsum and phosphorus production slag. A preliminary operation was performed to remove hygroscopic moisture from the filler.The influence of the nature of mineral fillers on the chemical stability and durability of the obtained composites is investigated. The nature of the interaction of mineral fillers with a polymer binder was determined, and chemical interaction of the hydroxyl groups of the filler and the methyl groups of the polymer took place. The mathematical planning method was used to optimize the chemical resistance and durability of the compositions of the studied substances. Based on the results of this study, optimal compositions of compositions, anhydrite, phosphogypsum and phosphoric slag were selected. These composites, with the highest possible degree of filling, have high target characteristics.

This review explores the potential of microalgae as a sustainable and nutritionally rich alternative for mineral supplementation in poultry diets, addressing both the opportunities and challenges in this emerging field. Poultry nutrition, pivotal to the health and productivity of birds, traditionally relies on inorganic and organic mineral sources, which, while effective, raise environmental and economic concerns. Microalgae offer a promising solution with their high content of essential minerals, proteins, vitamins, and bioactive compounds. The review delves into the nutritional profile of various microalgae, highlighting their rich mineral content, crucial for physiological processes in poultry. It examines the bioavailability of these minerals and their impact on poultry health and productivity. Furthermore, it evaluates the environmental sustainability of microalgae cultivation and acknowledges the challenges in using microalgae in poultry diets, particularly in terms of the economic viability of large-scale production and the consistency of nutrient composition. It discusses the importance of rigorous safety assessments and regulatory compliance, given the potential risks of toxins and heavy metals. Overall, this analysis aims to provide a clear understanding of the role microalgae could play in poultry nutrition and address sustainability challenges in animal agriculture, while also considering future perspectives and advancements needed in this field.

As semi-airborne mineral exploration has limited budgets, it is critical to design experimental procedures that generate data maximizing the desired information We investigate the effects of transmitter-receiver geometries for a variety of anomalies and semi-airborne layouts. Our simulations indicate that 200 m flight line spacing and 100 m point distance are the optimal trade-off between coverage and survey progress for various targets. Based on the target size and distance between the transmitter and the target, the transmitter length should be at least equal to the length of the target and for more than 1 km, at least two or three times the target size. Likewise important are the location and direction of the transmitter cables, which can have great impact on the result of inversion and should be parallel to the target strike. By using more than one transmitter, better results are obtained. If the strike of the target is known, transmitters should be parallel to each other and if not, it is better to use perpendicular transmitters. Results showed that the optimal distance between transmitters is 3 km. Our simulations show that it is even possible to recover targets just below the transmitter in corresponding areas of masked data.

The climate change impacts on some regions of the planet faster and stronger. These areas are known as the hot spots for climate change and Cyprus (Nicosia) in the Mediterranean is one of these spots. This paper aims to analyze the significant changes of atmospheric aerosol characteristics in 2019 and during the extreme event of 25 April 2019. We study the aerosol optical thickness (AOT), Ångström exponent, single scattering albedo, refractive index (imaginary and real parts), size, and vertical distribution of aerosol particles during the event of a high atmospheric aerosol contamination over Nicosia in details. For this purpose, we used the ground-based lidar, observations of the sun-photometer AERONET Nicosia station, satellite products from the Moderate Resolution Imaging Spectroradiometer (MODIS), and back trajectories of air movements calculated using the Hybrid Single Particle Lagrangian Integrated Trajectory Model (HYSPLIT). On 23–25 April, according to lidar and sun-photometer observations, strong aerosol pollution over Nicosia was detected. On April 25, 2019, the AOT value exceeds 1.0 at λ = 440 nm. Analysis of the optical and microphysical characteristics supported that the pollution consists of mainly Saharan dust and partly urban aerosols. This assumption was confirmed by HYSPLIT backward trajectories and MODIS images where air masses containing dust particles came from North Africa and from the Eastern part of Europe.

Nutrient management of lowbush blueberry (Vaccinium angustifolium Ait.) depends on several yield-limiting features. Machine learning models can process such yield-impacting variables to predict berry yield. We investigated the effects of local variables on yields and nutrient management of lowbush blueberry. We collected 1504 observations from N-P-K fertilizer trials conducted in Quebec, Canada. Meteorological indices at various phenological stages showed the greatest impact on yield. High mean temperature at flower bud opening and after fruit maturation, and total precipitation at flowering showed positive effects. Low mean temperature and low total precipitation before bud opening, at flowering, and by fruit maturity, as well as number of freezing days (< -5ºC) before flower bud opening, showed negative effects. Soil fertility variables, leaf nutrient compositions and N-P-K fertilization showed smaller effects. Gaussian processes predicted berry yields from historical weather data, soil analysis, fertilizer dosage, and leaf nutrients with a root-mean-square-error of 1447 kg ha-1 on the testing data set. An in-house Markov chain algorithm optimized yields modelled with Gaussian processes from leaf nutrient composition, soil test value, and fertilizer dosage conditioned to specified historical weather features. We propose to use conditioned machine learning models to manage nutrients of lowbush blueberry at local scale.

This work describes and interprets the presence of heavy minerals in the western Portuguese continental margin using a set of 78 bottom samples collected from 3 distinct areas of this margin: Porto, Aveiro and Nazaré canyon head areas. The main transparent heavy mineral suite (minerals with frequencies >10%), is composed by amphiboles (hornblende), mica (biotite), andalusite, tourmaline and garnet. A secondary suite (minerals with frequencies between 1 and 10%), is composed by pyroxene (enstatite, diopside and augite), staurolite, zircon and apatite. With very low frequency representing less than 1% we found rutile, olivine, kyanite, monazite, epidote, sphene, anatase, sillimanite and brookite. The main primary sources (igneous and metamorphic rocks) explain the presence of these minerals. However, the application of the principal component analysis, with a previous application of the centered log ratio transformation of the heavy mineral data, also stresses for the importance of the grain sorting as a process in controlling the heavy mineral occurrence. The importance of this process is mostly sustained by the distribution pattern of mica and of the most flattened amphibole grains in a way that these particles tend to have a hydraulic affinity to finer grained sediments.

The present study examines the effect of SiO2 nano-additives on the performance and emission characteristics of a diesel engine fuelled with soybean biodiesel. Soybean biofuel was prepared using the transesterification process. Nano-additives characterisations were done using different tests such as FESEM, XRD, EDS, etc., to study the morphology of nano-additives. For proper blending of nano-additives with biodiesel, the ultrasonication process was used. Surfactant was used for the stabilisation of nano-additives. After making all the combinations of nano fuel blends, physicochemical properties were measured as per ASTM standards. Performance and emissions readings were taken at different load conditions. It was found that with the addition of SiO2 nano-additives, brake thermal efficiency (BTE) and brake specific fuel consumption (BSFC) was increased by 3.48-6.39% and 5.81-9.88%, respectively. Significant reduction of CO, CO2, NOx, and smoke emissions were also observed compared to baseline fule due to better combustion efficiency with the use of SiO2 nano-additive.

The nutritional composition of food for animal production can be completed using olive tree and plant by-products due to their high contents of bioactive compounds, such as pentacyclic triterpenes. Here, we present a novel application of near-infrared spectroscopy (NIRS) for the prediction of the total or individual [maslinic acid (MA), oleanolic acid (OA), and uvaol (UO)] pentacyclic triterpene concentrations in a feed additive obtained from a plant mixture. The oxygen radical absorbance capacity of these types of samples demonstrated the existence of a high antioxidant capacity. The conventional determination methods of pentacyclic triterpenes concentration are costly, labor-intensive, and not practical for analyzing several lines within a limited timeframe at the factory level. The optimal regression model developed in our work demonstrated high correlation values for the calibration and validation sets, along with a high residual prediction deviation value. The NIRS method can be applied directly to dried powder and avoids extraction and high-performance liquid chromatography (HPLC) analysis. Our results also demonstrate that NIRS can accurately quantify pentacyclic triterpenes even at low concentrations in food additives. It can be used at the factory level to directly determine the concentrations in the additive powder obtained at the same time that the powder is produced.

In order to further reduce the emissivity of the hydrophobic low infrared emissivity composite coating and improve the mechanical properties of the coating, the dispersant, adhesion enhancer, and defoamer were used to improve the dispersion state of the fillers, the interface structure, and the surface state of the hydrogen silicone oil modified polyurethane/Al composite coating. The effects of dispersant, adhesion enhancer, and defoamer on the micro-structure, emissivity, glossiness, hydrophobic property, and mechanical properties of the coating were systematically studied. The results show that the polycarboxylate anionic dispersant can obviously improve the dispersion state of flake Al powder and nano-SiO2 in the coating, so that the infrared emissivity of the coating can be reduced, and the coating can have higher hydrophobic and mechanical properties. The bonding strength between the resin matrix and the metal substrate of the coating can be significantly improved by the adhesion enhancer through the bridging action, so that the adhesion strength and impact strength of the coating can be significantly improved. The defoamer can significantly reduce the pores in the coating, so that the surface state of the coating can be significantly improved, and the mechanical properties of the coating can be significantly improved. The coating has the best emissivity (0.527), glossiness (4.3), adhesion strength (grade 1), impact strength (40 kg.cm), and hydrophobic property (water contact angle (WCA) is 140o) when the amount of dispersant, adhesion enhancer, and defoamer is 5 wt%, 4 wt%, and 1 wt%, respectively.

In the field of construction, materials referred to as sustainable are currently undergoing a process of technological development. This study aims to contribute to the understanding of the behavior of the fundamental properties of concretes prepared with recycled coarse aggregates that incorporate in their matrix a polyethylene terephthalate-based additive in an attempt to reduce their high porosity. Techniques to measure the gas adsorption, water porosity and x-ray diffraction (XRD) were used to evaluate the effect of the additive on the physical, mechanical and microstructural properties of these concretes. Porosity reductions of up to 30.60% are achieved with the addition of 1, 3, 4, 5, 7 and 9% of the additive, defining a new state in the behavioral model of the additive (the overdosage point) in the concrete matrix; in addition, the porous network of these concretes and their correlation whit other physical and mechanical properties are also explained.

The carbonation of industrial calcium-rich byproducts such as steel slag demonstrates significant potential for CO2 sequestration. This technique aids in reducing carbon emissions while also promoting waste recycling. Despite its advantages, gaps remain in understanding how steel slag characteristics and operational parameters influence the carbonation process, as well as the underlying mechanism of direct aqueous carbonation. We evaluated the carbonation performance of three types of steel slag at temperatures below 100°C using a gas–liquid–solid reaction system. The slag with the highest CO2 sequestration capacity was chosen for a systematic evaluation of the effects of operating conditions on carbonation efficiency. Thermodynamic analysis indicated that the reactivity of CaO and Ca(OH)2 with CO2 exceeded that of CaO•SiO2 and 2CaO•SiO2. Under conditions of 85°C, a particle size less than 75 μm, an initial CO2 pressure of 0.5 MPa, a liquid-to-solid ratio of 5 mL/g, and a stirring speed of 200 rpm, the steel slag achieved a sequestration capacity (K) of 283.5 gCO2/kg and a carbonation efficiency (ζCa) of 51.61%. Characterization of the slag before and after carbonation using X-ray diffraction, SEM‒EDS, thermogravimetric analysis, and Fourier transform infrared spectrometry confirmed the formation of new carbonates. Mechanistic analysis revealed that the rate-limiting step initially involved the mass transfer of CO2, transitioning to Ca2+ mass transfer as time progressed. Our research provides a viable technique for CO2 capture and a beneficial approach for reutilizing waste steel slag. Furthermore, solid residues after capturing CO2 have the potential for conversion into carbon-negative building materials, offering a sustainable strategy for steel companies and other enterprises with high carbon emissions.

Microbial-mediated biogeochemical cycling of iron is widespread in anaerobic environments such as sediments and deep Earth aquifers, and is one of the major pathways for metabolising iron in nature. Organic matter containing quinone groups can act as electron shuttles to transfer electrons between microorganisms and Fe(III) oxides, facilitating the biotransformation of iron; this process also influences the transport transformation of pollutants. In this paper, the reduction of Fe(III) oxides by aniline in the heterogeneous iron-reducing bacterium Shewanella oneidensis MR-1 mediated by the electron shuttle AQS was investigated. The results showed that aniline significantly promoted the reduction of Fe(III) by MR-1 in the AQS-mediated reaction, and the best Fe(III) reduction was achieved in the reaction group of "GT+MR-1+0.5mM AQS+3μM aniline", in which the Fe(II) production was significantly higher than that in the reaction groups of only microorganisms and no aniline reaction. The amount of Fe(II) produced was significantly higher than that of the microorganism-only and aniline-free reaction groups, and the addition of aniline also significantly increased the consumption of sodium lactate by MR-1 in the reaction system. The solid mineral Fe(II)-O content increased to 41.32% after the reaction. However, the structure of needle ferrite is relatively stable, and the surface morphology did not change significantly by SEM, and the generation of other secondary minerals was not observed in the XRD results. The results of this experimental study can help to understand the biogeochemical cycle of iron in multicomponent reactions and are of great significance for environmental management.

In this paper, mineralogical and elemental geochemical characteristics of massive sulfide samples collected from Jade hydrothermal field, located in the Izena depression in the central graben of Okinawa Trough, were analyzed by means of optical microscopy, scanning electron microscopy and electron probe. The results show that the sulfide in Jade hydrothermal area can be divided into Zn-Cu-Pb rich massive sulfide and Zn-Fe rich massive sulfide. The former is composed of sphalerite, galena, anglesite, chalcopyrite and pyrite, and its formation stage can be divided into pyrite stage, sphalerite-chalcopyrite stage, anglesite stage and colloidal pyrite stage. The latter is mainly composed of sphalerite, pyrite, marcasite and a small amount of galena, which can be divided into galena stage, pyrite stage, sphalerite stage, pyrite and marcasite stage. Cu and Zn in pyrite may exist in the form of microinclusions, while Ag and Pb may exist in pyrite in the form of fine galena inclusions containing Ag. Fe and Cu may enter sphalerite in the form of ion replacement. Zn may enter chalcopyrite in the form of ion replacement, and As and Pb may be inclusions in chalcopyrite as As-bearing galena inclusions. Consistent with the previous understanding, the metal elements in the hydrothermal liquid system in Jade hydrothermal field mostly migrate with the hydrothermal fluid as sulfur complexes, and when the hydrothermal fluid mixes with seawater, the physical and chemical conditions of the fluid change, resulting in sulfide mineral precipitation. However, the chemical structure of chalcopyrite is still controversial, which restricts the understanding of the substitution mechanism of trace elements during chalcopyrite precipitation.

The aim of this study was to analyse the biocompatibility of a material based on lactic acid (PLA)/polyhydroxybutyrate(PHB)/thermoplastic starch (TPS) in combination with additives (plasticizers: acetyltributyl citrate (ATBC) and oligomeric lactic acid ( OLA)). Three types of materials were tested: I: PLA/PHB/TPS + 25% OLA, II: PLA/PHB/TPS + 30% ATBC, III: PLA/PHB/TPS + 30% OLA. The 3D printing itself was preceded by the creation of filaments from granulate and the design of samples. A filament production machine – Composer 450 (3devo; The Netherlands) was used to produce the filaments. Experimental samples were produced by FDM technology on a 3D printer DeltiQ2 (Trilab, Czech Republic). The evaluation of the biocompatibility of the materials included cytotoxicity tests such as the monitoring of viability, proliferation, morphology of cells, and their settlement on the surface of the materials. The cell line 7F2 osteoblasts (Mus musculus) was used in the experiments. Based on the tests, results confirmed the significant influence of plasticizers and their proportions in the mixtures. PLA/PHB/ATBC + 25% OLA was evaluated as the optimal material for biocompatibility with 7F2 osteoblasts. The tested biomaterials have the potential for further investigation, with a possible change in the proportion of the plasticizer, which has a fundamental impact on their biological properties.

Abstract: The promotion of sustainable packaging is part of the European Green Deal and plays a key role in the EU’s social and political strategy. One option is the use of renewable resources and biomass waste as raw materials for polymer production. Lignocellulose biomass from annual and perennial industrial crops and agricultural residues are a major source of polysaccharides, proteins, and lignin, and can also be used to obtain plant-based extracts and essential oils. Therefore, these biomasses are considered as potential substitute for fossil-based resources. Here, the status quo of bio-based polymers is discussed and evaluated in terms of properties related to packaging applications such as gas and water vapor permeability as well as mechanical properties. So far, their practical use is still restricted due to lower performance in fundamental packaging functions that directly influence food quality and safety, the length of shelf life and thus the amount of food waste. Besides bio-based polymers, this review focuses on plant extracts as active packaging agents. Incorporating extracts of herbs, flowers, trees, and their fruits is inevitable to achieve desired material properties that are capable to prolong the food shelf life. Finally, the adoption potential of packaging based on polymers from renewable resources is discussed from a bioeconomy perspective.

We hypothesized that rumen fluid with yeast producing cellulase enzyme can occur and also produces a high biomass compared to S. cerevisiae. Therefore, the aim of this study was to screen and isolate yeast from rumen fluids with an experimental design method. We optimized a fermentation medium containing sugarcane molasses as a carbon source and urea as a nitrogen source to measure the efficiency of biomass production and cellulase activity. Two fistulated-crossbred Holstein Friesian steers, averaging 350 ± 20 kg body weight, were used to screen and isolate ruminal yeast. The two experiments were designed. A 12 × 3 × 3 factorial was used in a completely randomized design to determine biomass and carboxymethyl cellulase activity. Factor A was isolated yeasts and S. cerevisiae. Factor B was sugarcane molasses (M) concentration. Factor C was urea (U) concentration. Potential yeast was selected for identified and analyzed as a 4 × 3 factorial use in a completely randomized design including. Factor A was incubation times. Factor B was isolated yeast strains including code H-KKU20 (as P. kudriavzevii-KKU20), I-KKU20 (C. tropicalis-KKU20), and C-KKU20 (as Galactomyces sp.-KKU20). Isolation was under aerobic conditions, resulting in a total of 11 different colonies. We noted two appearances of colonies including, asymmetric colonies of isolated yeast (indicated as A, B, C, E, and J) and ovoid colonies (coded as D, F, G, H, I, and K). The highest biomass was observed in three yeasts including codes H, I, and C-KKU20 when inoculated in 25% molasses with 1% urea (M25+U1) (p <0.01). The highest CMCase activity was observed in yeast code H-KKU20 when inoculated in all media solutions (p <0.01). Ruminal yeasts strains H-KKU20, I-KKU20, and C-KKU20 were selected for their ability to produce biomass and their CMCase enzyme synthesis. Identification of isolates H-KKU20 and I-KKU20 revealed that those isolates belonged to Pichia kudriavzevii-KKU20 and Candida tropicalis-KKU20, while C-KKU20 was identified as Galactomyces sp.-KKU20. Two strains provided maximum cell growth: P. kudriavzevii-KKU20 (9.78 and 10.02 Log cell/ml) and C. tropicalis-KKU20 (9.53 and 9.6 Log cells/ml) at 60 and 72 h of incubation time, respectively. The highest ethanol production was observed in S. cerevisiae: 76.4, 77.8, 78.5, and 78.6 g/L at 36, 48, 60, and 72 h of incubation time, respectively (p <0.01). The P. kudriavzevii-KKU20 yielded the least reducing sugar about 30.6 and 29.8 g/L at 60 and 72 h of incubation time, respectively. It could be concluded that screening and isolating yeast from rumen fluids resulted in 11 different characteristics of yeasts. The first novel yeasts discovered in the rumen fluid of cattle were Pichia kudriavzevii-KKU20, Candida tropicalis-KKU20, and Galactomyces sp.- KKU20. P. kudriavzevii-KKU20 had higher results than the other yeasts in terms of biomass production, cellulase enzyme activity, and cell number.

A review of influence of drag-reducing agents on curved pipe flows is presented in this work. In addition, this review outlined proposed mechanism, friction factor and fluid flux models for drag-reducing agents in curved pipe flows. Our finding reveals that drag reduction by additives in curved pipes is quite significant but generally lower than the corresponding drag reduction in straight pipes. It decreases with increase in curvature ratio and more pronounced in the transition and turbulent flow regimes. Drag reduction strongly depends on the polymers and surfactants’ concentrations as well as the bubble fraction of micro-bubbles. It is also reported that drag reduction in curved pipes depends on temperature and existence of dissolved salts in the fluids. Maximum drag reduction asymptote differed between straight and curved pipes and between polymer and surfactant. No definite conclusion could be drawn as regards drag reduction for two-phase flow in curved pipes due to the limited studies in this area. Many questions such as the mechanism of drag reduction in curved pipes and how drag-reducing agents interact with secondary flows still remained unanswered. Hence, some research gaps have been identified with recommendations for areas of future researches.

The effects of the additives (silicon carbide and titania) and sintering temperatures on the phases developed, physical and mechanical properties of sintered mullite-carbon ceramic composite produced from kaolin and graphite was investigated. The kaolin and graphite of known mineralogical composition were thoroughly blended with 5 and 3 (vol.) % silicon carbide and titania respectively. From the homogeneous mixture of kaolin, graphite and titania, standard samples were prepared via uniaxial compaction. The test samples produced were subjected to firing (sintering) at 1300˚C, 1400˚C and 1500˚C. The sintered samples were characterized for the developed phases using x‐ray diffractometry analysis, microstructural morphology using ultra‐high resolution field emission scanning electron microscope (UHRFEGSEM). Various physical and mechanical properties were determined. It was observed that the addition of SiC/TiO2 additives to the samples made them to possess very low oxidation indices .This also resulted in improvement in the bulk densities and cold crushing strength of the sample when compared with those without additives. It was concluded that the addition of SiC/TiO2 additives improves on the high temperature oxidation resistance of the mullite-carbon ceramic composite sample.

The circular economy is based on maintaining a circular flow of resources. Policymakers face difficulties in balancing national security and circular economy aspects in the field of mineral resources policy. With a uniquely expanded input-output table, this study estimates the final destination of several critical minerals (lithium, cobalt, yttrium, lanthanum, cerium, neodymium and dysprosium) and base metals (iron, copper and aluminum) in the Japanese economy for 2015. Our model shows quite a good similarity between the estimated composition and the actual data of products. The results reveal a detailed distribution of critical minerals and indicate prioritized implementation for creating and maintaining a circular flow of critical minerals. Developed decision flow guidance provides a comprehensive approach to national security and circular economy aspects for policymakers. For further actions, inclusive indicator development is required for policymakers to support the determination of implementation possibilities from social and technological aspects.

The roots of African grapes (Lannea microcarpa) have long been utilised in traditional medicine for their perceived therapeutic properties. However, their comprehensive proximate and mineral analysis remains largely unexplored. Proximate composition and mineral content of the roots were conducted. The sample was obtained from Katsayal, Katsina State, and analysed using standard procedures. The macro and micro metals were determined using Flame Photometer and Atomic Absorption Spectroscopy, respectively. The results revealed a moisture content of 28.0 ±2.0%, an ash content of 21.3±1.2%, and significant levels of crude fibre (29.0±0.50%), crude lipid (9.60±0.20%), crude protein (6.91±0.01%), and available carbohydrates (33.3±0.10%). The calorific value of the root was determined to be 245 ± 0.01 kcal/g. The micro-mineral analysis revealed the detection of copper (8.60 ± 0.002 mg/kg), magnesium (9.24 ± 0.004 mg/kg), manganese (41.9 ± 0.001 mg/kg), iron (405 ± 0.042 mg/kg), and zinc (9.46 ± 0.001 mg/kg). The macro-minerals, namely calcium (28400 mg/kg), potassium (1530 mg/kg), and sodium (45030 mg/kg), were found to be present in the sample. It is advisable to conduct additional research to examine the identified minerals' bioavailability, clarify the phytochemical profile, and investigate potential bioactive compounds.

The proton conductivity, phase composition and mechanical properties of (1-x)CsH2PO4–x fluoropolymer electrolytes (x-mass fraction, x=0-0.3) have been investigated firstly and discussed. UPTFE and PVDF-based polymers (F2M, F42, SKF26) with the high mechanical properties and thermal stability have been chosen as a fluoropolymer additive. According the XRD data, a monoclinic CsH2PO4 (P21/m) phase is retained in all compositions of the polymer electrolytes studied. The conductivity of (1-x)CsH2PO4-x fluoropolymer in the high-temperature phase decreases by approximately one order of magnitude compared with the pure CsH2PO4 for x~0.15-0.20. The size and shape of CsH2PO4 particles and their distribution have been shown to affect significantly the proton conductivity and mechanical properties of the membranes. The thin-film composite systems were produced by various methods of the obtaining salt particles, their mixing and applying to a polymer matrix. The uniform distribution of particles in the polymer systems with the size of ~300 nm was achieved by a pretreatment of the suspension in a bead mill. CsH2PO4-based mechanically strong membranes with the thickness ~50–100 μm were obtained for the soluble fluoropolymers (F2M, F42, SKF26). With an increase in the mass fraction of the polymer the ability of the membranes to resist the plastic deformation and the mechanical strength increases and comparable to the best low temperature membranes. The proton-conducting membranes (1-x)CsH2PO4 – x fluoropolymer with the optimal combination of the conductivity, mechanical and hydrophobic properties are promising for use in solid acid fuel cells.

This paper analyzes the mitigation of enteric methane (CH4) emissions from ruminants with the use of feed additives inhibiting of rumen methanogenesis to limit global temperature increase to 1.5 °C. A mathematical simulation conducted herein predicted that pronounced inhibition of rumen methanogenesis with pure chemicals or bromoform-containing algae can contribute to limit global temperature increase by 2050 to 1.5 °C only if widely adopted at a global level and considering an efficacy higher than obtained in most studies. Currently, the most important limitations to the adoption of antimethanogenic feed additives are probably increased feeding cost without a consistent return in production efficiency, and achieving sustained delivery of inhibitors to the rumens of non-supplemented, extensively ranging animals. Economic incentives, and changes in rumen microbial metabolism caused by inhibiting methanogenesis, could potentially be used to make the methanogenesis inhibition intervention cost effective. Also, the composition of the methanogenic community, and rate of disappearance of inhibitors of methanogenesis in the rumen can influence the effective dose of the inhibitors, and hence the cost of their adoption. Possible means for sustained delivery of antimethanogenic compounds to extensively grazing animals are discussed. Limitations and knowledge gaps of these approaches, and future research directions, are examined.

Mineral profile of beef interests human health, but also animal performance and meat quality. This study analyzes the relationships of 20 minerals in beef (ICP-OES) with 3 animal performance and 13 meat quality traits analyzed on 182 samples of Longissimus thoracis. Animals’ breed and sex showed limited effects. The major sources of variation (farm/date of slaughter, individual animal within group and side/sample within animal) differed greatly from trait to trait. Mineral contents were correlated to animal performance and meat quality being significant 52 out of the 320 correlations at the farm/date level, and 101 out of the 320 at the individual animal level. Five latent factors explained 69% of mineral co-variation. The most important, “Mineral quantity” factor correlated with age at slaughter and with the meat color traits. Two latent factors (“Na+Fe+Cu” and “Fe+Mn”) correlated with performance and meat color traits. Two other (“K-B-Pb” and “Zn”) correlated with meat chemical composition and the latter also with carcass weight and daily gain, and meat color traits. Meat cooking losses correlated with “K-B-Pb”. Latent factor analysis appears be a useful means of disentangling the very complex relationships that the minerals in meat have with animal performance and meat quality traits.

Filter Media (FM) sourced from recycled organic and mineral material offers a low cost and effective means of treating urban stormwater. Using recycled materials rather than from an increasingly scarce source of virgin materials (typically sandy loam soil) can ensure a sustainable long-term economy and environment. This paper presents results from the laboratory analysis and mathematical modeling to highlight the performance of recycled organic and mineral material in removing nutrients and metals from stormwater. Analysis included physical and chemical characterisation such as particle size distribution, saturated hydraulic conductivity (Ksat), bulk density, effective cation exchange capacity, and pollutant removal performance. Design mixes (DM), comprising a combination of organic and mineral materials, were characterised and used to develop/derive modelling design within the Model for Urban Stormwater Improvement Conceptualisation (MUSIC v6) [1]. Comparison is made to the Adoption Guidelines for Stormwater Biofiltration Systems - Summary Report [2] which were based on the Facility for Advancing Water Biofiltration (FAWB) guidelines to assist in the development of biofiltration systems, including the planning, design, construction and operation of those systems. An observed outcome from over two decades of biofiltration guideline development has been the exclusion of alternative biofilter materials due to claims of excessive leaching. Results from this study indicate that high nutrient and metal removal rates can be achieved over a range of hydraulic conductivities using design mixes of recycled organic and mineral materials that have a demonstrated equivalence to existing guideline specifications.

While the demand in reduction of CO₂ increases, the need for CO₂ sequestration processes is very high. One promising technology is the Carbon Capture and Storage (CCS). In this paper we refer to several papers which study the three main steps in CCS chain. CO₂ capture technologies, CO₂ transportation to the storage sites and the very critical step the CO₂ storage. Recently a novel method (mineral carbonation) for CO₂ sequestration has been proposed which is based in the reaction of CO₂ with calcium or magnesium oxides or hydroxides to form stable carbonate materials. Greece is a country that emits CO₂ mainly from the lignite fired power plant in Western Greece. After the study of the bibliographic references about the use of mineral carbonation process while injecting CO₂ in the appropriate geological forms we concluded that there are also these forms in our country and mainly in the area near to the power plant such as in sites Vourinos and Pindos. In these sites exist minerals rich in oxides and hydroxides of Ca, Mg and Fe representing the perfect materials for mineral carbonation.

To address the question whether there is evidence that drinking water in general or mineral water in particular is effective in preventing diabetes; we performed a literature search of randomized controlled trials (PubMed). The search resulted in very few trials (N = 9) investigating this topic: one trial investigates the effect of increasing water consumption on glycemic control in diabetic patients; two trials investigate the effect of drinking water with a meal in diabetic patients; while six trials compare the effect of mineral rich water with that of low mineralized water on glucose metabolism in healthy subjects. There is evidence that increasing water consumption can improve glucose metabolism and randomized controlled trials with mineral water suggest that waters containing relevant amounts of magnesium can exert an additional effect. The role of bicarbonate; which is present in all the mineral waters used in the trials; will be discussed. Future research needs to investigate the effect of mineral water in prediabetic individuals or individuals with impaired glycemic control.

In no-tillage systems, there is an accumulation of crop residues (CR) which plays an important role in available of soil-N. A study was set up to provide information regarding the CR N credit, and the influence of N mineral fertilizer. An incubation was run in a loam soil with addition of a similar rate of residue (10 Mg ha-1; sugarcane, soybean, and brachiaria) and N mineral fertilizer (urea; 120 kg N ha-1). After the stabilization of biological activity, soil and remaining residues were collected, and N monitored. Results showed that the N credit was positive with application of soybean, sugarcane, and brachiaria. There was an expressive performance of soybean N credit represented by a positive balance, and a reduction from 2.49 to 0.9 g kg-1 of N in residue, with direct increase of 90% of soil-N. There is no need of N fertilizer to potentialize the soybean N credit, but it is requested to potentialize N credit of brachiaria and sugarcane. The urea demonstrated be a good enhancer of brachiaria N credit, but it was not adequate to sugarcane residues. Based in our result, the accumulation and incorporation of CR can be considered as a N credit with positive contribution in soil-N.

This study assessed the impact of mineral fertilization on tuber yield and food quality of yam genotypes, specifically Dioscorea alata and Dioscorea rotundata. Four genotypes, each from D. alata and D. rotundata, were used in field experiments conducted in Ibadan, Nigeria, in the 2017 and 2018 cropping seasons. Experiments were conducted under low soil NPK fertility conditions with and without fertiliser treatments. A recommended NPK rate for the area (90, 50, and 75 Kg N, P, K ha-1) was applied to plots with fertiliser treatment. Tuber yield, functional and pasting properties of yam flour, and sensory attributes of pounded yams were collected. The results showed differential responses of the genotypes to tuber yield and food quality with fertiliser application. Fertiliser application has generally increased fresh tuber yield, but it has affected some genotypes' flour quality and textural attributes of the pounded yams. As regards genotypes Danacha and TDa0200012, fertiliser application has increased tuber yield without causing a decrease in tuber quality hence, suggesting Danacha and TDa0200012 as suitable genotypes for maximizing fertiliser productivity. However, in another genotype Ojuiyawo, fertiliser application effectively increased tuber yield but deteriorated tuber quality. Our results suggested that it is crucial to determine the impact of fertilisation on tuber yield and quality for each genotype and select the appropriate genotype to improve productivity through mineral fertilisation. The results of this study can be widely applied to enhance yam productivity in sub-Saharan Africa and useful for sustainable agriculture in yam-growing areas.

This article presents, for the first time, the kinetics and the general conversion features of free radical polymerization (FRP) in a 3-component system (A/B/N), with [A] being the initiator, and [B] and [N] are additives, based on the proposed mechanism of Rahal et al. Higher FRP can be achieved by additives [B] and [N], via the dual function of (i) regeneration [A], and (ii) generation of extra radicals (R) via the radicals (S' and S) produced by N.The initiator (coumarin) shows a dual photo-oxidation and photo-reduction character for high efficacy. The FRP conversion efficacy (CE) depends not only on the property of the initiator [A], the additives [B] and [N}, but also the types of monomers. For example, when [A]=CoumC, [A]/NPG is more efficient than [A]/Iod, but revserse trend occurs in some monomers. However, 2-component systems (with CE=0% to 80%) are always less efficient than that of 3-component systems (with CE=70% to 86%, in TMPTA). Specific systems with [A]=coumarins, [B]=Iodonium salt, and N=NPG are analyzed. Analytical formulas for the role of each component concentration, light intensity and coupling rates on the conversion efficacy are derived.

Arsenic, an element of environmental impact, can be incorporated into jarosite–type compounds and remain stabilised within the structure under a wide range of environmental conditions. In this study, a sample of ammonium–arsenic jarosite was synthesised by precipitation in sulphate medium at controlled pH of 1.2–1.8. The behaviour of arsenic during the thermal and chemical decomposition of jarosite was analysed; the degradation in alkaline medium of jarosite was also studied. According to the results, the synthesised jarosite is composed of joined rhombohedral crystals, forming tightly spherical shaped particles, 37–54 μm size. The ammonium jarosite produced possessed a high arsenic concentration; its calculated stoichiometry being (NH₄)Fe_2.45[(SO₄)_1.80(AsO₄)_0.20][(OH)_4.15(H₂0)_1.85]. It was found that arsenic is stabilised in the jarosite structure; upon heating, it remains in residual solids above 700°C, whilst in alkaline medium an incongruent dissolution takes place, with the arsenic retained in the solid phase along with iron. These solids, when exposed to high temperatures (1200°C), transform into a type of iron oxide known as hematite, so with arsenic it is retained an iron compound forming a stable compound which withstands high temperatures.

A new method is proposed for performance assessment of lubricating compositions based on industrial lubricants that contain nano-additives of different chemical composition for higher wear resistance of heavy-loaded steel friction pairs. The method is based on the joint analysis of the experimental data on the wear kinetics, change of the relative hardness, and damage in the surface layers of the metal of friction pairs. The level of structural damage to the materials in the contact zone is determined by using the statistical parameters of dispersion of the hardness values. The paper investigates the known experimental results of assessment of the level of damage to structural materials of various grades under the conditions of long-term, cyclic, static loading, and lubricated friction. It is demonstrated that the structural changes occurring in the materials during loading correlate to the changes in the statistical dispersion characteristics of hardness measurement results. Experimental substantiation of the method is carried out for steel friction pairs using lubricating compositions based on industrial oil Greaseline Lithium BIO Rail 000 by AIMOL and nano-additives of copper of M2 grade, magnesium alloy of MA2 grade, aluminum alloy of Al-Mg system, graphite of medium carbon steel grades, i.e. rail and industrial. Under system of indicators presented in the paper, the highest efficiency in terms of increase in the wear resistance of steel friction pairs is demonstrated by the lubricating composition based on industrial lubricant with the additive of nano-powder made of rail steel, as it provided the optimum value of friction coefficient, minimum damage and wear of friction surface.

This review aimed to analyze the effects of additives in the process of producing silage from re-hydrated corn grains for ruminants. Control treatment studies used in this analysis was corn grain rehydrated with water only. To be included in the review, the studies needed to follow stand-ardized criteria, including the absence of additives in the control treatment and the evaluation of the silage in beef animals, such as cattle, goats, and sheep. A total of seven publications, published between 2014 and 2022, were included in the final dataset. To compare the results, the PROC ANOVA of SAS was used, which included a random effect of comparison within the study, per-forming a paired comparison. It was observed that the use of additives did not influence the chemical composition, pH, organic acid and ethanol content, microbial population, fermentative losses, aerobic stability, and dry matter in vitro digestibility of rehydrated corn grain silage (p >0.05). Based on this information, it is concluded that the use of additives in rehydrated corn grain silage did not show major differences on silage quality. It is important, however, to evaluate the effects of additives in silages on animal performance.

Regeneration of biological tissues in medicine is challenging, and 3D bioprinting offers an innovative way to create functional multicellular tissues. One common way in bioprinting is bioink which is one type of the cell-loaded hydrogel. For clinical application, however, the bioprinting still suffers from satisfactory performance, e.g. in vascularization, effective antibacterial, immunomodulation and regulation of collagen deposition. Many studies have incorporated different bioactive materials into the 3D printed scaffolds to optimize the bioprinting. Here, we review a variety of additives added to the 3D bioprinting hydrogel. The underlying mechanisms and methodology for biological regeneration are important and will provide useful basis for future research.

We performed for the first time to our knowledge fully ab initio molecular dynamics simulations of additive tribochemistry in boundary lubrication conditions. We consider an organophosphourus additive that has been experimentally shown to reduce friction in steel-on-steel sliding contacts thanks to the tribologically-induced formation of an iron phosphide tribofilm. The simulations allow us to observe in real time the molecular dissociation at the sliding iron interface under pressure and to understand the mechanism of iron phosphide formation. We discuss the role played by the mechanical stress by comparing the activation times for molecular dissociation observed in the tribological simulations at different applied loads with that expected on the basis of the dissociation barrier.

This study compared the relative effect of two trace mineral supplementation strategies recom-mended in France for newborn beef calves. 600 calves were supplemented with 20 mg oral sele-nium (OTM group) at birth (D0) or by injection (ITM group) of a multi-mineral solution (60 mg of Zn, 10 mg of Mn, 15 mg of Cu, 5 mg of Se) on D0, D30 and D60. Mortality and the incidence rate of diseases, including diarrhea, omphalitis, pneumonia, as well as medicinal treatments, were recorded from D0 to D210. The incidence rate of omphalitis was significantly lower in the ITM group than in the OTM group (respectively 11% vs. 17%, P = 0.036). The cumulative inci-dence rate of all health troubles was lower in the ITM group than in the OTM group (P=0.007). Except for pneumonia, incidence of diarrhea (24% vs. 22%), use of oral (7% vs. 6%) or IV rehydra-tion therapy (4% vs. 2%) or use of antibiotics (43.3% vs. 38.0%) and mortality (3% vs 2%) were numerically higher in OTM group than in ITM group (n.s.). In this study, ITM supplementation is as efficient as oral supplementation regarding calves' health status. It reduces the risk of ompha-litis at the calf level effectively.

This study aims to assess the feasibility of delineating and identifying mineral ores from hyperspectral images of tin-tungsten mine excavation faces using machine-learning classification. We compiled a set of hand samples of minerals of interest from a tin-tungsten mine and analyzed two types of hyperspectral images: 1) images acquired with a laboratory set-up under close-to-optimal conditions; and 2) scan of a simulated mine face using a field set-up, under conditions closer to those in the gallery. We have analyzed the following minerals: cassiterite (tin ore), wolframite (tungsten ore), chalcopyrite, malachite, muscovite, and quartz. Classification (Linear Discriminant Analysis, Singular Vector Machines and Random Forest) of laboratory spectra had a very high overall accuracy rate (98%), slightly lower if the 450 – 950 nm and 950 – 1780 nm ranges are considered independently, and much lower (74.5%) for simulated conventional RGB imagery. Classification accuracy for the simulation was lower than in the laboratory but still high (85%), likely a consequence of the lower spatial resolution. All three classification methods performed similarly in this case, with Random Forest producing results of slightly higher accuracy. The user’s accuracy for wolframite was 85%, but cassiterite was often confused with wolframite (user’s accuracy: 70%). A lumped ore category achieved 94.9% user’s accuracy. Our study confirms the suitability of hyperspectral imaging to record the spatial distribution of ore mineralization in progressing tungsten-tin mine faces.

In this work the effect of recycled concrete aggregate modified with mineral admixtures and Nano-silica on the mechanical properties and performance of the concrete was investigated after curing in tap water for 28 and 90 days. The compressive, ƒc, indirect tensile, ƒt, and flexural, ƒb, strengths for cured concrete specimens were measured and concrete strength ratios were analyzed. The water and rapid chloride permeability were measured. SEM analysis of microstructure was, also, investigated. The coarse aggregates used were dolomite (control) and recycled concrete aggregate with the incorporation of different mineral admixtures including ground granulated blast slag and granite as well as Nano-silica. It was found that, the slump values of the dolomite concrete decreases compared with recycle aggregate concrete. The results indicate that, the concrete mix containing recycle aggregate have the highest compressive strength, tensile strength and flexural strength compered to concrete mix containing dolomite aggregate. As far as the compressive strength is concerned, the addition 1 % NS and 15 % of slag improved the physico-mechanical properties of the recycled aggregate concretes compared to the other mixes after curing in tap water.

The aim of this study was to assess the effects of supplementation of inorganic sources of manganese (MnO, MnSO4), zinc (ZnO, ZnSO4) and copper (CuSO4) at different levels (0.06%DM for Mn, 0.05%DM for Zn; and 0.01 and 0.05%DM for Cu) on in vitro rumen fermentation, solubility and bioavailability. Fermentation activity was measured by total gas production (TGP) and dry matter degradability after 70hrs of fermentation (dDM%). Trace-mineral (TM) solubility was estimated by the TM concentration in the supernatant of the final fermentation medium (SOL) and TM bioavailability by the TM concentration in a bacterial enriched fraction (BACT). Mn (regardless of source) and ZnO tended (p&lt;0.10) to decrease, while Cu showed no significant effect on TGP. The addition of inorganic Mn and of ZnO tended (p&lt;0.10) to decrease, ZnSO4 tended to increase (p&lt;0.10), whilst Cu showed no effect on dDM%. Concerning solubility, Mn (MnO and MnSO4), ZnSO4 and CuSO4 significantly (p&lt;0.05, p&lt;0.001 and p&lt;0.01) increased, while ZnO did not affect TM content of the SOL. These results indicate that MnSO4, ZnSO4 and CuSO4 are highly soluble, MnO is quite soluble, while ZnO has a low solubility in the rumen. Based on the TM content of BACT, MnO, MnS4 and CuSO4 have a high bioavailability, while ZnO is poorly assimilated by rumen bacteria. However, the lack of clear inhibition or improvement of fermentations suggests that the rumen microbiota has low requirement for TM supplementation.

Italian Directives recommends the good quality of natural mineral waters but literature data assert a potential risk from several microorganisms colonizing wellsprings and mineral water bottling plants. Aim of study is the identification of microorganisms from spring waters (SW) and bottled mineral waters (BMW) samples. Methods: Routine microbiological indicators, Legionella spp., Nontuberculous mycobacteria (NTM), protozoa (FLA) and physical-chemical parameters were assessed in 24 SW and 10 BMW samples performing culture methods and molecular tests as PCR and qPCR. Results: In 33 out of 34 samples no cultivable bacteria were isolated with the exception of 83 CFU/L of Mycobacterium gilvum, detected in one warm rich-mineralized SW. qPCR showed the presence of Legionella genomic units in 24% of samples (mean 2,9x10²±1,7x10² GU/L) and NTM genomic units in 18% of samples (mean 5,7x10^3±4,1x10³ GU/L). Vermamoeba vermiformis and Acanthamoeba polyphaga were recovered respectively in 70% of BMW samples (counts from 1,3x10³ to 1,2x10⁵) and 42% of SW samples (counts from 1,1x10³ to 1,3x10⁴). Vahlkampfia spp. was detected in 42% of SW and 70% of BMW samples (mean 1,3x10⁴ ±2,9x10³ GU/L). Conclusion: The study highlights a low rate of microbial risk and the importance of risk assessment in natural mineral waters.

The basis of modern teeth whitening systems is the use of a whitening gel, usually containing hydrogen peroxide or carbamide peroxide. The purpose of our study was to evaluate the effect of chemical and modified office teeth whitening systems on the mineral metabolism of oral fluid and to determine a safer method. The study covered 81 patients aged 22 to 35 years of both sexes with teeth color A2 and darker on the Vita Classic scale. Determination of the concentration of calcium and phosphates in the oral fluid was carried out on a spectrophotometer using ready-made Human kits. Chemical tooth whitening was performed using a gel based on 40% hydrogen peroxide. After the procedure, remineralization therapy with enamel-sealing liquid was performed for 14 days. The obtained results indicate that the most pronounced changes in the content of calcium (+74.4%, p &lt;0.001) and рhosphates (phosphorus) (-23.07%, p &lt;0.001) were observed when using a chemical bleaching system. After the teeth whitening procedure using a modified technique, less pronounced changes in the concentrations of calcium (+29.07, p &lt;0.001) and phosphorus (-14%, p &lt;0.001) were observed. The use of remineralizing agents led to a faster recovery of the initial levels of calcium and phosphates in the oral fluid. Both bleaching systems caused similar changes in the chemical composition of the oral fluid.

Cadmium, an environmental toxin, is associated with a range of adverse health effects due to increased Reactive Oxygen Species production, including decreased bone mineral density and osteoporosis. Notably, cadmium is found at concentrations 4-5x higher in the blood of smokers versus non-smokers. Experiments performed in human cancer cells indicate that melatonin may directly protect against cadmium-induced tissue damage via regulation of mitochondrial activity. Further, recent evidence has demonstrated that melatonin can improve bone health for individuals with osteoporosis and partially protect against cadmium-associated inhibition of bone repair. Here we review this data and propose supplementation with melatonin as a strategy to protect against the negative impacts of cadmium exposure on bone mineral density within individuals regularly exposed to cadmium via cigarette smoking.

A major problem in the post-inversion geophysical interpretation is the extraction of geological information from inverted physical property models, which do not necessarily represent all underlying geological features. No matter how accurate the inversions are, each inverted physical property model is sensitive to limited aspects of subsurface geology and is insensitive to other geological features that are otherwise detectable with complementary physical property models. Therefore, specific parts of the geological model can be reconstructed from different physical property models. To show how this reconstruction works, we simulated a complex geological system that comprises an original layered earth model that has passed several geological deformations and alteration overprints. Linear combination of complex geological features comprised three physical property distributions: Electrical resistivity, induced polarization chargeability, and magnetic susceptibility models. This study proposes a multivariate feature extraction approach to extract information about the underlying geological features comprising the bulk physical properties. We evaluated our method in numerical simulations and compared three feature extraction algorithms to see the tolerance of each method to the geological artifacts and noises. We show that the fast-independent component analysis (fast-ICA) algorithm by negentropy maximization is a robust method in the geological feature extraction that can handle the added unknown geological noises. The post-inversion physical properties are also used to reconstruct the underlying geological sources. We show that the sharpness of the inverted images is an important constraint on the feature extraction process. Our method successfully separates geological features in multiple 3D physical property models. This methodology is reproducible for any number of lithologies and physical property combinations and can recover the latent geological features, including the background geological patterns from overprints of chemical alteration.

From 1964 to the early 1970s, Orson Anderson led a research program at the Lamont Geological Observatory in the newly-emerging field of “mineral physics”. In collaboration with colleagues Edward Schreiber and Naohiro Soga, Orson exploited the techniques of physical acoustics to study the behavior of the sound velocities of minerals at elevated pressures and temperatures. This research program also included semi-empirical studies of relationships between the bulk modulus and the molar volume of solids and the use of lattice dynamics to calculate the elastic moduli of cubic structures as a function of pressure to predict instabilities, as well as theoretical investigations of the Lagrangian vs. Eulerian formulations of finite strain equations of state.

An innovative concrete that incorporates the advantages of self-compacting concrete with geopolymer is called self-compacting geopolymer concrete. The objective of this study was the Manufacturing of M30-grade self-compacting geopolymer concrete by adding industrial materials like fly ash (FA), ultrafine ground granulated blast furnace slag (UFGGBS), and silica fume (SF) as minerals. The disposal of these industrial wastes can be substantially overcome, as they lead to land pollution. The fixed powder content was 500 kg/m³. A mixture of sodium silicate (Na₂SiO₃) and sodium hydroxide (NaOH) created an alkaline solution that activated the cementitious binders. In this study, slump flow, L-box, V Funnel, T50 V Funnel, and J ring tests were carried out to determine the fresh qualities of the concrete. These tests were conducted under the regulations for self-compacting concrete provided by EFNARC (2005). To improve the flexural strength of the SCGC, 1.5 % glass fibre was added. This study illustrates how an artificial neural network (ANN) model can determine the concrete mix proportion. The characteristics of SCGC, both fresh and hardened properties test were investigated for molarities of 8, 10, and 12. The microstructural outcomes were determined using Fourier-transform infrared spectroscopy (FT-IR), scanning electron microscopy (SEM), and X-ray diffraction (XRD).

Scanning electron microscopy (SEM) is a powerful tool in the domain of material science, mining, and geology, owing to its enormous potential to provide unique insights into the micro and nanoscale worlds. This comprehensive review discusses the background development of SEM, basic SEM operation including the specimen preparation and imaging process, and fundamental theoretical calculations underlying the SEM operation. It provides foundational understanding to the engineers and scientists, who never got a chance to dig in-depth into the SEM, to understand the working and development of this robust analytical technique. The present review covers how SEM has been serving as a crucial tool in mineral characterization, with specific discussions on the working and research fronts of SEM-EDX, SEM-AM, SEM-MLA, and QEMSCAN. With automation gaining pace in the development of all spheres of technology, the understanding of uncertainties in SEM measurements is very important. The constraints in mineral phase identification by EDS spectra and sample preparation are conferred. In the end, future research directions for SEM are analyzed with the possible incorporation of machine learning, deep learning, and artificial intelligence tools, for automating the process of mineral identification, quantification, and efficient communication with the researchers, so that the analytical process robustness and objectivity can be improved, and the analysis time and the involved costs can be brought down. This review also discusses the idea of integrating robotics with SEM, to make the equipment portable, so that further mineral characterization insights can be gained not only on earth but also on other terrestrial grounds.

The causal effects of chondroitin, glucosamine, and vitamin/mineral supplement intake on kidney function remain unknown, despite being commonly used. We conducted a two-sample summary-level Mendelian randomization (MR) analysis to test for causal associations between regular dietary supplement intake and kidney function. Genetic instruments for chondroitin, glucosamine, and vitamin/mineral supplement intake were obtained from genome-wide association study of European ancestry. Summary statistics for the log-transformed estimated glomerular filtration rate (log-eGFR) were provided by the CKDGen consortium. The multiplicative random-effects inverse variance-weighted method showed that genetically predicted chondroitin and glucosamine intake was causally associated with a lower eGFR (chondroitin, eGFR change beta = -0.113 %, standard error (SE) = 0.03 %, P-value = 2E-04; glucosamine, eGFR change beta = -0.240 %, SE = 0.035 %, P-value = 6E-12). However, a genetically predicted vitamin/mineral supplement intake was associated with a higher eGFR (eGFR change beta = 1.426 %, SE = 0.136 %, P-value = 1E-25). Validation analyses and pleiotropy-robust MR results for chondroitin and vitamin/mineral supplement intake supported the main results. Our MR study suggests a potential causal effect of chondroitin and glucosamine intake on kidney function. Therefore, clinicians should carefully monitor their long-term effects.

Food authorities aim to safeguard our food. This requires sensitive analyses to guarantee detection of both banned and regulated substances at low concentrations. At the same time, broad screening methods are needed to identify new emerging risks. For this purpose effect-based bioassays combined with mass spectrometric analyses offer an advantage. During the regular monitoring of dioxins in agricultural products, a discrepancy was observed between the results of the DR CALUX (Dioxin-Responsive Chemical Activated Luciferase gene Expression) bioassay and the confirmatory gas chromatographic high resolution mass spectrometric (GC-HRMS) analysis in egg and broiler fat samples. The response in the bioassay was high, suggesting a clear exceedance of the maximum limits of dioxins in these samples, yet regulated dioxins or dl-PCBs were not detected by GC/HRMS analysis . Ultimately, a broad screening analysis using GC-HRMS resulted in the identification of 2,3,7,8-tetrabromo-dibenzofuran (2,3,7,8-TBDF) in both egg and broiler fat. To investigate the potential; source of this brominated furan contaminant, different samples were analysed: bedding material, poultry feed, feed additives (choline chloride and L-lysine) and seaweed. The poultry feed and feed additives all contained 2,3,7,8-TBDF. Using a feed to food converter, it became clear that the poultry feed was probably the source of 2,3,7,8-TBDF in broilers and eggs through a feed additive like L-lysine or choline chloride. This study underlines the importance of using a combination of effect based screening assays with sensitive analytical methods to detect potential new and emerging risks.

Nitrogen fertilization ensures the proper growth of trees. The aim of the study was to evaluate the impact of differentiated nitrogen fertilization on selected parameters. It was assumed that such analysis is an indirect picture of the needs of cherries grown in herbicide fallow. The content of minerals in two layers of the soil, in leaves, and its influence of tree growth, and the content of chlorophyll in leaves were assessed. The experiments were carried out in three different cherry orchards. Three levels of fertilization were applied in each orchard: 0 kg, 60 kg and with 120 kg N ha- 1. As expected the fertilization resulted in an increase in the content of nitrate and ammonium forms of nitrogen in the soil, however, their content was also dependent on precipitation and temperature. Additionally a high nitrogen fertilization increased the content of phosphorus and potassium and decreased the magnesium in the topsoil layer. High nitrogen fertilization caused the decrease of content of phosphorus and potassium in the leaves. The level of calcium and magnesium in leaves increased with fertilization of 60 kg N ha–1 but decreased with the dose to 120 kg N ha–1. The use of nitrogen fertilization increased the vegetative growth of trees measured by leaf area and trunk cross-sectional area. However, the chlorophyll content was not dependent on the amount of nitrogen fertilization.

Studies of the fundamental origins of friction have undergone a rapid acceleration in recent years by providing valuable information on the nanoscale mechanisms responsible for the friction at the macroscopic level. Significant efforts have been directed into developing composite nanofluids and nanoparticle additives to unlock new tribological properties unattainable by traditional lub-ricants. The studies are now further evolving by developing methods to achieve active control of the nano- and/or mesoscale friction by application of magnetic and electric fields external to the contact. These methods constitute an area of rapidly growing interest, and they also are illumi-nating how the performance of conventional lubricants could be enhanced through synergistic addition of nanoparticles (NPs). This mini-review highlights 25 publications that collectively re-veal significant progress, as well as important outstanding challenges, to a fundamental under-standing of how the addition of NPs impacts the lubricant performance. The first two sections focus on the use of Quartz Crystal Microbalance (QCM), a technique that spans atomic to mac-roscale length and time scales. Subsequent sections expand to complimentary methods comparing results at the macro and atomic scale for similar materials. These studies highlight the pivotal role of the nanoparticle charge and surface treatment, while also indicating that rolling of nano-particles is ineffective and/or detrimental.

The results from laboratory tests and field tests, available in the open literature for over ten years, despite the announcement of high efficiency translating into increased energy efficiency and such significant ecological advantages, have not so far resulted in widespread use of fuel performance catalysts (FPC) on a global scale. Wishing to explain why the above situation occurred and to verify the operation of catalytic additives for fuels; this article presents the results of research on the effect of using catalytic additives for fuel in a brand new diesel engine. The article contains an analysis of the results of exhaust gas emission tests from the Doosan MD196TI engine. During the tests, the engine was fueled with a typical diesel fuel and the same fuel with the a catalyst additive. The catalyst was added to the liquid fuel in the form of a commercially available product distributed by ProOne company under the name FMAX. The research was carried out in the form of a test, much more developed than the approval test on a stationary braking station in accordance with the requirements of ISO 8178. The article is concluded with a comparative analysis of exhaust gas emission results illustrating the effects of a catalyst in the form of reduction of solid particles, carbon monoxide, hydrocarbons and a slight increase in nitrogen oxide emissions. In addition, the effect of the catalyst depends on the product of thermal (brake) efficiency of the engine and the calorific value (CV) of the fuel used.

A new di-mannitol adipate ester-based zinc metal alkoxide (DMAE-Zn) was synthesized as a bi-functional PVC thermal stabilizer for the first time. The materials were characterized with Fourier-transform Infrared spectroscopy (FT-IR) and thermogravimetric analysis (TGA). Characterization results confirmed the formation of Zn-O bonds in DMAE-Zn; and that DMAE-Zn had a high decomposition temperature and a low melting point. The thermal stability of DMAE-Zn on PVC also was tested by conductivity test, thermal aging test, and UV-visible spectroscopy (UV-VIS) test. PVC stabilized by DMAE-Zn had a good initial color and excellent long-term stability. UV-VIS also showed that the conjugated structure in PVC stabilized by DMAE-Zn was almost all of the triene, suggesting that the addition of DMAE-Zn would suppress the formation of conjugated structures above tetraene. Dynamic processing performance of PVC samples tested by torque rheometer indicated that, having a good compatibility with PVC chains in the amorphous regions, DMAE-Zn contributed good plasticizing effect to PVC. DMAE-Zn thus effectively demonstrates bi-functional roles, e.g., thermal stabilizers and plasticizers to PVC. Furthermore, FT-IR, HCl absorption capacity test, and complex ZnCl₂ test were also used to verify the thermal stability mechanism of DMAE-Zn for PVC.

For the first time, it is shown that inhaled ambient air-dust particles settled in the human lower respiratory tract induce lung calcification. Chemical- and mineral compositions of pulmonary calcium precipitates in the lung right lower-lobe (RLL) tissues of 12 individuals who lived in Upper Silesia Conurbation in Poland and who had died from causes not related to lung disorder were determined by transmission- and scanning electron microscopy. Whereas calcium salts in lungs are usually reported as phosphates, calcium salts precipitated in RLL are almost exclusively carbonates, i.e. Mg-calcite and calcite. These constitute 37% of 1652 mineral particles examined. Mg-calcite predominates in the submicron size range with the MgCO3 content up to 50 mol%. Magnesium plays a significant role in the lung mineralization, a fact so far overlooked. The calcium phosphate (hydroxyapatite) content in RLL is negligible. The predominance of carbonates is explained by increased CO2 fugacity in RLL. Carbonates enveloped inhaled mineral-dust particles, including uranium-bearing oxides, quartz, aluminosilicates, and metal sulfides. Three possible pathways for the carbonates precipitation on the dust particles are postulated: (1) precipitation of amorphous calcium carbonate (ACC) followed by its transformation to calcite; (2) precipitation of Mg-ACC followed by its transformation to Mg-calcite; (3) precipitation of Mg-free ACC causing a localized relative enrichment in Mg ions and subsequent heterogeneous nucleation and crystal growth of Mg-calcite. The actual number of inhaled dust particles may be significantly greater than observed because of the masking effect of the carbonate coatings. There is no simple correlation between smoking habit and lung calcification.

Aiming at the industrial scale development of a Scandium (Sc)-selective leaching process of Bauxite Residue (BR), a sufficiently numerous set of process design aspects has been investigated, by appropriate exploitation of available experimental data. The interpretation of experimental data for Sc leaching yield, with sulfuric acid as the leaching solvent, has shown significant impact from acid feed concentration, mixing residence time, liquid to solids ratio, and times of leachate re-usage onto fresh BR. The thin film diffusion model, as the fundamental theory for leaching, either with constant particle size for selective leaching, or with shrinking particle size for less-, or non-, selective leaching, interprets sufficiently well the relevant experimental data. In both cases, a concept for an unyielding core supplements the basic model. Especially for the selective leaching mild conditions, the simplest model version keeps step with the experiments, since both prove 1^st order kinetics, while especially for the extreme conditions including very low solvent excess, it is proposed a combined conversion rate model with diffusion and chemical reaction inside particles. The maximization of Sc recovery per unit of consumed solvent (i.e., specific recovery) emerged as highly critical for the process economics.

Polymer-based composites represent a separate class of materials in demand by the industry. In comparison with other polymers, UHMWPE is characterized by exceptionally high wear and impact resistance. In this work, compacts were produced from UHMWPE GUR 4120 powder with the addition of Nanoscale Detonation Carbon (NDC) and Single-Walled Carbon Nanotubes (SWCNTs) on a hydro-pneumatic impact device by the Cyclic Impact Compaction (CIC) technique. The obtained samples were subjected to wear resistance test, their hardness and tensile strength were measured. Studies have shown that the addition of NDС and SWCNTs in UHMWPE leads to an increase in hardness by 6.4 and 19.6%, to a decrease in wear by 11.5 and 38.5% and a decrease in the coefficient of friction by 10 and 20%, respectively. However, the tensile strength of UHMWPE decreases by 11.7 and 40.4% and elongation decreases by 11.9 and 30.1% with the addition of NDС and SWCNTs, respectively.

We studied the influence of lava meal, zeolite and top layer of sandy soil as bedding additives on gaseous C and N losses from a sloping-floor barn of naturally ventilated animal housing. We selected four barn units where eight young bulls’ group was reared in each barn. Chopped straw of wheat and barley applied daily at the rate of 5 kg per livestock unit (LU) in bedding areas where one LU consisted of 500 kg body mass of live bulls. Zeolite, lava meal and sandy soil (18% clay + silt) applied in barn at the rate of 10, 20 and 30% of straw dose, respectively. Static flux chamber was used to measure gases emissions from the barn unit and mass balance calculation was used to calculate straw manure total N (TN) losses during housing phase. On an average, all bedding additives decreased 85% of the NH₃ emission compared to control; however, they did not influence CH₄ emission. Zeolite decreased CO₂ (35%) and N₂O (37%) emission rates. Subsequently, lava meal, sandy soil and zeolite decreased 23, 37, and 50% of TN losses from barn manure, respectively. Overall, measured N emissions through NH₃-N and N₂O-N from the barns was 11% of calculated TN losses while remainder 89% was most probably attributed to di-nitrogen (N₂), a harmless gas. Hence, in straw-based cattle housings, zeolite could be a promising additive for reduction of CO₂, N₂O and NH₃ emissions and sandy soil can be considered as cheap and readily available resource for reducing NH₃ emission.

One of the most important objectives of the studies worldwide is to improve the performance of automotive engines to reduce fuel consumption and environmental pollution. Accordingly, the principal motivation of this research study is improving the tribological behavior of the piston ring/cylinder liner interfaces as a promising and straightforward approach in automotive fuel economy and increasing engine durability using Al₂O₃ and TiO₂ nanomaterials as smart nano-lubricant additives that adapted to different operating conditions by replenishing mechanisms anti-friction and anti-wear in automotive engines.

Carbon dioxides capture chemical looping combustion (CLC) technology uses metal oxides as oxygen transporters (TO). (1) These oxygen transporters, OXMN009 and OXMN009P, are used in a cyclic process that prevents the formation of nitrogen oxides by keeping air and fuel separate. (2) Thermogravimetric balance (TGA) experiments were conducted to evaluate the kinetic behavior of these copper-modified oxygen transporters. (3) It was found that OXMN009P has improved reactivity and oxygen transfer properties due to copper impregnation. The kinetic parameters obtained in the TGA indicate that the reaction is non-thermal and requires less energy to initiate. (4) The results show that OXMN009P has reactivity comparable to other manganese-based materials reported in the literature and can be an effective option for carbon dioxide capture.