The rational design of magnetic carbon composites, encompassing both composition and microstructure, holds significant potential for achieving exceptional electromagnetic wave absorbing materials (EAMs). In this study, FeCo@CM composites was efficiently fabricated through an advanced microwave plasma assisted reduction chemical vapor deposition (MPARCVD) technique, offering high efficiency, low cost, and energy-saving benefits. By depositing graphitized carbon microspheres, the dielectric properties were significantly enhanced, resulting in improved electromagnetic wave absorption performances through optimized impedance matching and a synergistic effect with magnetic loss. A systematic investigation revealed that the laminar-stacked structure of FeCo exhibited superior properties compared to its spherical counterpart, supplying a higher number of exposed edges and enhanced catalytic activity, which facilitated the deposition of uniform and low-defect graphitized carbon microspheres. Consequently, the dielectric loss performance of the FeCo@CM composites was dramatically improved due to increased electrical conductivity and the formation of abundant heterogeneous interfaces. At a 40 wt% filling amount and a frequency of 7.84 GHz, the FeCo@CM composites achieved a minimum reflection loss value of -58.2 dB with an effective absorption bandwidth (fE) of 5.13 GHz. This study presents an effective strategy for developing high-performance EAMs.

The normal growth and development of skeletal muscle is essential for the health of the body. The regulation of skeletal muscle by intestinal microorganisms and their metabolites has been continuously revealed. Acetate is the predominant short-chain fatty acid synthesized by gut microbiota through the fermentation of dietary fiber, however, the underlying molecular mechanisms governing the interaction between acetate and skeletal muscle during rapid growth stage remain to be further elucidated; Here, specific pathogen-free (SPF) mice, germ-free (GF) mice, and germ-free mice supplemented with sodium acetate (GS) were used to evaluate the effects of acetate on skeletal muscle growth and development of young mice with gut microbiota deficiency; We found the concentration of serum acetate, body mass gain, succinate dehydrogenase activity and expression of myogenesis maker gene of skeletal muscle in the GS group was higher than GF group following sodium acetate supplement. Furthermore, the transcriptome analysis revealed that acetate activated biological processes regulating skeletal muscle growth and development in GF group that are inhibited due to gut microbiota deficiency. In vitro experiment, we proved that acetate up-regulated Gm16062 to promote skeletal muscle cell differentiation; Overall, our findings proved that acetate promote skeletal muscle growth and development in young mice via increase Gm16062 expression.

Background: While it is established that intravenous catheter placement duration is strongly linked to the risk of catheter colonization and bloodstream infections, there are still substantial knowledge gaps concerning the varying durations of PICC placement that lead to either infection or colonization by common pathogens, particularly MDR pathogens. The present study aims to compare the dwell time required for MDR pathogens to colonize with the time required to cause Central Line-Associated Bloodstream Infections (CLABSIs) in critically ill patients with PICCs and compares it with non-MDR pathogens, shedding light on the significance of preventive procedures to control MDR infections in clinical settings. Methods: Data from critically ill patients with PICCs admitted consecutively to «Metropolitan» Hospital in Athens, Greece, from May 2017 to May 2020 were retrospectively analysed. Results: In this study, 86 hospitalized patients, consisting of 56 (65.1%) males and 30 (34.9%) females, with a mean age of 55.67±21.1 years (range 16-91 years), presented with both CLABSIs and colonization following PICC placements. Specifically, 42 (48.8%) of them presented with CLABSIs, while 44 (51.2%) presented with colonization. Among the total participants, an MDR pathogen was isolated from 26 (30.2%) PICCs, while other pathogens were isolated from 60 (69.8%). The mean duration of catheter dwell time for all participants was 20.94±14.22 days (range 3-72 days). When analysed separately for each group, the dwell time for PICCs with CLABSIs was 25.73±16.19 days and 16.36±10.28 days for those with colonization (T test, p=0.002). Additionally, the mean dwell time for PICCs infected by non-MDROs was 22.48±15.64 days whereas for PICCs with MDROs, it was 17.38±9.5 days (T test, p=0.005). In PICCs with CLABSIs, the mean indwelling time for MDR pathogens was 21.50±12.31 days, while for non-MDROs, it was 27.73±16.98 days (T test, p=0.417). In PICCs with colonization, the mean dwell time for MDR pathogens was 15.55±7.73 days, while for non-MDROs, it was 16.92±11.85 days (T test, p=0.124). Among PICCs with MDR pathogens (n=26), the mean duration in CLABSIs events (n=18) was 21.5±12.31 days and in colonization events 15.55±7.73 days, (n=8) (T test, p=0.146). Conclusions: The present study reveals that colonization of PICCs exhibited a shorter dwell time compared to those with CLABSIs. Moreover, PICCs infected by MDROs had a shorter mean dwell time than those with non-MDROs. These findings underscore the importance of considering infection status and microbial resistance patterns when evaluating PICC dwell times.

The present study aims at investigating the potential impact of agricultural policies on GHG emissions from agriculture across the European Union. The study begins with a brief analysis of the context of implementation of the 2014-2022 Common Agricultural Policy (CAP), within which many interventions were designed to improve sustainability and increase competitiveness. It follows a description of the structural changes the European agriculture is witnessing, that are both influenced and contribute influencing policies. The method of Qualitative Comparative Analysis (QCA) is used to investigate possible causalities and to cluster observations based on similar combinations of conditions (i.e., drivers) and outcomes (i.e., positive or negative variations in GHG emissions from agriculture between the end and the begin of the CAP programming period). The results reveal that the increase in GHG emissions from agriculture over the study period is mainly attributable to the low share of agricultural land under management contracts targeting climate change mitigation and carbon sequestration through the CAP. CAP payments coupled with the production is found to contribute to further increasing GHG emission from agriculture in some eastern and northern EU countries. Livestock concentration, income support payments and the high price of agricultural land drive the increase in GHG emissions for other central and eastern EU countries. The paper concludes addressing existing shortcomings due to conflicting interventions in the current CAP Strategic Plans.

Glycosidic linkage analysis was conducted on the unfractionated polysaccharides in the alcohol-insoluble residues (AIRs) prepared from six red seaweeds (Gracilariopsis sp., Prionitis sp., Mastocarpus papillatus, Callophyllis sp., Mazzaella splendens, and Palmaria palmata) using GC-MS/FID analysis of partially methylated alditol acetates (PMAAs). The cell walls of P. palmata primarily contained mixed-linkage xylans and small amounts of sulfated galactans and cellulose. In contrast, the unfractionated polysaccharides of the other five species were rich in galactans displaying diverse 3,6-anhydro-galactose and galactose linkages with varied sulfation patterns. Different levels of cellulose were also observed. This glycosidic linkage method offers advantages for cellulose analysis over traditional monosaccharide analysis that is known for underrepresenting glucose in crystalline cellulose. Relative linkage compositions calculated from GC-MS and GC-FID measurements showed that anhydro sugar linkages generated more response in the latter detection method. This improved linkage workflow presents a useful tool for studying polysaccharide structural variations across red seaweed species. Furthermore, for the first time, relative linkage compositions from GC-MS and GC-FID measurements, along with normalized FID and total ion current (TIC) chromatograms without peak assignments, were analyzed using principal component analysis (PCA) as a proof-of-concept demonstration of the technique's potential to differentiate various red seaweed species.

The aim of our study was a comprehensive comparative assessment of the effect of consumption of 1 and 2% cholesterol as part of a standard diet with and without regular moderate physical activity on the main biomarkers of lipid and cholesterol metabolism, as well as the intestinal microbiota of male Wistar rats. The animals were randomly divided into 5 groups according to body weight and Open Field test results: Control (n=10), 1% Chol (n=10), 2% Chol (n=10), 1% Chol + RUN (n=10) and 2% Chol + RUN. The cholesterol was additionally added in the amount of 1g or 2g/100g, respectively, to the diet of animals. The rats of experimental groups 1% Chol + RUN and 2% Chol + RUN were subjected to regular (2 days a week) physical activity on a Treadmill. In rats of four experimental groups, when compared to the Control, a response of 39 indicators was revealed. The largest number of changes in biomarkers - 29 (statistically significant, p

The Axillary Seabream Pagellus acarne is of economic importance for recreational and commercial fisheries in the Atlantic and the Mediterranean, but a decline in total landings has been observed and raised some concern. Although biological information on the species has been provided for the Atlantic and Mediterranean, in the Portuguese continental slope data is restricted to the southern part of the country, which points to the relevance of the present work. A total of 520 individuals, between 7.8 cm and 39.9 cm TL, were monthly collected from September 2020 to August 2022 from commercial landings of fishing vessels operating off mainland Portugal, and used to study age and growth, the reproductive strategy and the annual sexual cycle. Age varied between 0 years (7.8 cm TL) and 15 years (34.2 cm TL) and the von Bertalanffy growth parameters were estimated from whole-otolith readings (L∞ = 35.2 cm, k = 0.133 yr–1 and t 0 = –2.78 yr). Pagellus acarne proved to be a protandric hermaphrodite species with males prevailing until 28.0 cm TL and females between 28.0 cm and 34.0 cm TL with a brief sex change phase. Females presented asynchronous oocyte development with a batch spawning pattern. The spawning season occurred from April to October with a spawning peak between June and August aas shown by histological analysis of the gonads and high levels of GSI during the period.

The study findings revealed significant variability in various wood properties among different genetic families, although the static modulus of elasticity did not exhibit significant differences between the chosen genetic families. All measured wood properties decreased from the bottom to the top of the model trees. Wood hardness displayed a moderately negative correlation with wood density and weak correlations with MOE and MOR. Given the weak correlations between wood hardness and other wood mechanical properties, it is suggested that the MOEdyn would be a more suitable trait for genetic studies.

This study presents the design and comprehensive 3D multiphysics simulation of a novel microfluidic immunosensor for real-time, non-invasive monitoring of pro-inflammatory biomarkers in human sweat. The patch-like device, designed using COMSOL Multiphysics, integrates magnetofluidic manipulation with direct-field capacitive sensing. The sensor comprises two distinct units: an immunocomplex enhancement unit, employing a series of microcoils to optimize the binding efficiency, reaction kinetics, and homogeneity of biomarker-magnetic nanoparticle (MNP) interactions, thereby enhancing the sensor's specificity; and a layered capacitive sensing unit, designed to concentrate and detect biomarker-tagged MNPs, thus amplifying sensitivity. Simulations of the capacitive sensing unit revealed a substantial sensitivity increase of up to 42.48\% at an 85\% MNP concentration within the detection zone. These findings highlight the potential of the proposed immunosensor for efficient and precise real-time biomarker monitoring, which may facilitate early disease diagnosis and enable personalized healthcare interventions.

The COVID-19 pandemic has triggered seismic shifts in how we work, and organizations behave. It has caused many organizations to transition from an office-centric culture to more flexible ways of working. This shift is necessitated by health conditions and the need for controls. It is also driven by the assumption that remote work or working from home offer a certain assurance of safety for employees against the threat of infection in highly vulnerable office conditions. The shift to remote work has so far been mainly experimental as most businesses continue to learn about what works and what doesn’t. There is also the assumption that all that matters for the efficient operability of a remote work regime is the availability and effectiveness of computing technologies and internet connectivity. Thus, once those supplies are in place remote work is expected to be fully functional and without problems. As learning continues about what works and what doesn’t, it has also become increasingly clear that beyond the threat of covid-19 and the relative safety that individual homes may offer, there are other vulnerabilities which are ignored or underestimated in the process. In most instances, the home environment of the employee, the conditions under which employees operate from home and the health and safety such environments provide (or not) are either ignored or underestimated in discussions around remote work practices. This paper highlights remote work as an emergent practice while exploring associated, but ignored, health and safety issues in employee homes.

With buildings accounting for a significant portion of global energy consumption and greenhouse gas emissions, the application of artificial intelligence (AI) holds promise for enhancing sustainability in the building lifecycle. This systematic literature review addresses the current understanding of AI's potential to optimize energy efficiency and minimize environmental impact in building design, construction, and operation. A comprehensive literature review and synthesis were conducted to identify AI technologies applicable to sustainable building practices, examine their influence, and analyze the challenges of implementation. The review was guided by a meticulous search strategy utilizing keywords related to AI application in sustainable building design, construction, and operation. The findings reveal AI's capabilities in optimizing energy efficiency through intelligent control systems, enabling predictive maintenance, and aiding design simulation. Advanced machine learning algorithms facilitate data-driven analysis and prediction, while digital twins provide real-time insights for informed decision-making. Furthermore, the review identifies barriers to AI adoption, including cost concerns, data security risks, and challenges in implementation. AI presents a transformative opportunity to enhance sustainability in the built environment, offering innovative solutions for energy optimization and environmentally conscious practices. However, addressing technical and practical challenges will be crucial for the successful integration of AI in sustainable building practices.

Moso bamboo is famous for fast growing and biomass accumulation, as well as high annual output for timber and bamboo shoots. These high outputs require high nutrient inputs to maintain and improve stand productivity. Soil nitrogen (N), phosphorus (P) and potassium (K) are important micronutrients for plant growth and productivity. Due to high variability of soils, analysing spatial patterns of soil N, P and K stocks is necessary for scientific nutrient management in Moso bamboo forests. In this study, soils were sampled from 138 locations across Yong’an City and ordinary kriging was applied for spatial interpolation of soil N, P and K stocks. Soil N stock showed a strong spatial dependence while soil N and P stocks presented a moderate spatial dependence, indicating soil N was mainly controlled by intrinsic factors while soil N and P stocks were controlled by both intrinsic and extrinsic factors. Different spatial patterns were observed for soil N, P and K stocks across the whole study area, indicating that fertilizations with different ratios of N:P:K should be applied for different sites to maintain and improve stand productivity. The total soil N, P and K stocks within 0-60 cm were 0.624, 0.020 and 0.583 Tg, respectively.

Cytologic diagnosis of extra‐adrenal paraganglioma presenting as a peripancreatic mass is challenging with a high rate of diagnostic error. We present a case of a peripancreatic mass identified by radiology as a gastrointestinal stromal tumor. Endoscopic ultrasound‐guided fine needle aspiration (FNA) of the mass showed a moderately cellular tumor composed of small to medium sized neoplastic cells with round to oval nuclei arranged singly and in loose clusters. The cells were positive for neuroendocrine markers (synaptophysin and chromogranin) and negative for CD117. A diagnosis of a neoplasm with a neuroendocrine tumor (NET) was made on FNA cytology. The subsequent surgical resection of the tumor revealed peripancreatic paraganglioma with immunohistochemistry positive for synaptophysin, chromogranin, and S100. The latter delineates the sustentacular cells. Although paraganglioma is a well recognized tumor, a detailed comparison of peripancreatic paraganglioma versus pancreatic/gastrointestinal NET is still lacking.

Australia has the highest small-mammal extinction rate in the world, and there are ample of reasons that have led to the higher extinction rates such as introduction of feral species, wildfires, climate change and uneven population distribution. All these factors instil a dire need to protect the species in captive environment. Stress has a major role to play in maintaining an adequate welfare conditions for wildlife, hence quantification of the stress levels in captive animals help us understand the effectiveness of the methods used to house the animals. In this study, we assessed the stress levels of captive marsupials namely Rufous bettongs (Aepyprymnus rufescens) (n=9), Long-nosed potoroo (Potorous tridactylus) (n=4) and Greater bilby (Macrotis lagotis) (n=5) by measuring the faecal cortisol metabolites using the Enzyme-Immuno assay (EIA) (R4866). We carried out a laboratory validation of the EIA for the Rufous bettongs and long-nosed potoroo by demonstrating parallelism between the pooled faecal samples and the standard curve. We also used the iterative baseline approach to calculate the baseline levels and detect peak concentrations of FCM in all the studied species. No significant differences were found in the FCM and baseline levels in the potoroos. Results highlighted a significant difference (p < 0.05) in the individual FCM and baseline levels of the bettongs. Additionally, significant differences (p < 0.05) were found in the FCM and baseline levels between male and female bettongs. In case of bilbies, the FCM and baseline levels showed no significant differences, however the male and female baseline levels were significantly different (p < 0.05). Our study provides the baseline and peak FCM concentrations in Long-nosed potoroos and Rufous bettongs under captive management. Future studies can use the iterative baseline approach and validated EIA to detect any possible variations in the FCM concentration and baseline values in captive marsupials created due to factors like sex, grouping, and housing conditions.

Apple-tree (Malus × domestica Borkh.) belongs to the genus Rosaceae. Due to its adaptability and tolerance to different soil and climatic conditions, it is cultivated worldwide for fresh consump-tion. Therefore, the priorities of apple growers are the high-quality of fruits and stable yield for high production. In total about 90 to 95 percent of fruits should fall or be eliminated from apple trees to avoid overcropping and poor-quality fruits. Several technologies such as handwork, me-chanically or chemical substances are used for fruit and bud elimination. The most profitable in commercial orchards is the use of chemicals for elimination, but due to the European Green Deal more environmentally sustainable solutions are required. Elimination of fruitlets is influenced by several factors. Additionally, the apple trees have the self-elimination mechanism. This is de-termined by apple genotype, physiological futures and genetics. This review focuses on the bio-logical factors and genetics mechanisms in apple yield self-regulation for better understanding the regulatory mechanism of fruitlets abscission for future breeding programs targeted on self-regulating yield apple varieties

Wildfires have always been a part of the history of Mediterranean forests. However, forest regeneration after a wildfire is not certain. It depends on many factors, some of which may be influenced by land management activities. Failure of regeneration will cause a regime shift in the ecosystem, reducing the provision of ecosystem services and ultimately leading to desertification. How can we increase Mediterranean forests’ resilience to fire? To answer this question, we did a literature review, investigating chains of processes that allow forests to regenerate (which we label “regeneration mechanisms”), and assessed the impact of selected management practices documented in the WOCAT database on the regeneration mechanisms. We identified three distinct regeneration mechanisms that enable Mediterranean forests to recover, as well as the time frame before and after a fire in which they are at work, and factors that can hinder or support resilience. The three regeneration mechanisms enabling a forest to regenerate after a fire consist of regeneration (1) from a seed bank; (2) from resprouting individuals; and (3) from unburned plants that escaped the fire. Management practices were grouped into four categories: (1) fuel breaks, (2) fuel management, (3) afforestation, and (4) mulching. We assessed how and under what conditions land management modifies the ecosystem’s resilience. The results show that land management influences resilience by interacting with resilience mechanisms before and after the fire, and not just by modifying the fire regime. Our analysis demonstrates a need for adaptive – i.e. context- and time-specific – management strategies.

In many European countries over the last decades, arable fields dominate agriculture landscapes, leading to a very intensive land-use practices. This reason seems to be the main cause of popula-tions declines for numerous farmland species, including the European hare (Lepus europaeus Pallas, 1778). The Research institute for Animal Production (National Agricultural and Food Centre, Luzianky, Slovakia) has been engaged in a long monitoring project (project currently run-ning), collecting certain indicators of hare population dynamics during hunting season since 1987 to 2023 in the Slovak Danubian Lowland. In the same macro-area (Čiližská Radvaň and Lehnice) a study was conducted on the influence of permanent semi-natural vegetation in relation to re-cruitment, population density and production. The whole monitored period was aggregated into 5-years intervals (for a total of 7 time-intervals), with the aim of analyzing the brown hare popu-lation dynamics. Spring hare density in the Danubian Lowland is currently 20.8 hares/km2, with harvests of 4.6 hares/km2. During all the monitoring period, bag’s animals have been examined following the regular hunting operations for the purpose of age determination (weight of eye lenses), sex ratio and productivity. The results of our analysis showed that the proportion of juve-nile in bag (PYB) among those shot varied from 37.0 % of the last 5-years interval (2018-2023), to a maximum of 51.0 % in interval of years 1998-2002. On total average there were 1.86 juveniles per adult female (r). The proportion of adult females in gamebag varied from 22.58 % (years in-terval 1992-1997) to 31.26 % (years interval 2018-2023). Sex-ratio (SI; males : females) among shot hares showed a value of 0.50, ranged from 0.48 in the period 2008-2012 to 0.52 in the first observed period (years 1987-1991) and in the last one (years 2018-2023). Average weight of shot hares was 4.04 kg (juveniles 3.83 kg, adults 4.27 kg, adult males 4.21 kg and females 4.32 kg). There was a large positive effect of set-aside with special mixtures, created for hares in large-scale farmed agrarian landscape, on hare density, bag and recruitment. In model hunting grounds with such set-asides increased the spring stock by 25 %, bag by 100 % and recruitment by 20 %. This study reveals that the management of European brown hare is not sustainable, and the population is decreasing. It is proved through the decline of harvest hares and by population dynamics parameters. Environmental improvements lead to the stabilization and increasing of requested parameters.

Driven by the growing interest of the scientific community and the proliferation of research in this field, cranial implants have seen significant advancements in recent years regarding design techniques, structural optimisation, appropriate material selection and fixation system method. Custom implants not only enhance aesthetics and functionality but are also crucial for achieving proper biological integration and optimal blood irrigation, critical aspects in bone regeneration and tissue health. This research aims to optimize the properties of implants designed from triply periodic minimal surface structures. The gyroid architecture is employed for its balance between mechanical and biological properties. Experimental samples were designed varying three parameters of the surface model: cell size, isovalue and shape factor. Computational simulation tools were used for determining the relationship between those parameters and the response variables: the surface area, permeability, porosity and Young modulus. These tools include computer aided design, finite element method and computational fluid dynamics. With the simulated values, the corresponding regression models were fitted. Using the NSGA-II, a multi-objective optimisation was carried out, finding the Pareto set which includes surface area and permeability as targets, and fulfil the constraints related with the porosity and Young modulus. From these non-dominated solutions, the most convenient for a given application was chosen, and an optimal implant was designed, from a patient computed tomography scan. An implant prototype was additively manufactured for validating the proposed approach.

Wavelength selective switches (WSSs) are essential elements for wavelength division multiplexing (WDM) optical networks, as they offer cost-effective, high port-count and flexible spectral channel switching. This work proposes a new hybrid WSS architecture that leverages the beam shaping and steering features of uniform silicon nitride (SiN) based end-fire optical phased arrays (OPAs). By introducing beamforming to a WSS system, the spectral channels on the liquid crystal on silicon (LCoS) panel can be tailored and arranged properly, depending on the optical configuration, using the beam control capabilities of OPAs. Combining 3D-FDTD and ray tracing simulations, the study shows that by reducing the input beam dimensions with proper sizing of the OPAs, the WSS design with the null-steering OPAs layout and 4×No switch size features increased spectral resolution. This extensive beamforming study on the steering-enabled layout reveals the acquirement of an even higher input channel number, achieving up to the 8×No WSS scheme with flexible channel routing on the LCoS panel. Such implementation of beamsteerers can unlock an extra degree of freedom for the switching capabilities of hybrid WSS devices. The results show great promise for the introduction of OPAs in WSS systems and provide valuable insight for the design of future wireless communication links and WDM systems.

Mosquitoes are responsible for the transmission of numerous pathogens, including Plasmodium parasites, arboviruses and filarial worms. They pose a significant risk to public health with over 200 million cases of malaria per annum and approximately four billion people at risk of arthropod-borne viruses (arboviruses). Mosquito populations are geographically expanding into temperate regions and their distribution is predicted to continue increasing. Mosquito symbionts, including fungi, bacteria and viruses, have desirable traits for mosquito disease control including spreading horizontally and vertically through mosquito populations and potentially colonising multiple important vector species. Paratransgenesis, genetic modification of mosquito symbionts with effectors to target the pathogen rather than the vector, is a promising strategy to prevent the spread of mosquito-borne diseases. A variety of effectors can be expressed but venom toxins are excellent effector candidates because they are target specific, potent, and, stable. However, the only toxins to be explored in mosquito paratransgenesis to date are Scorpine and mutated phospholipase A2. To enhance the scope, effectiveness, and durability of paratransgenesis, an expanded arsenal of effectors is required. This review discusses other potential toxins effectors for future paratransgenesis studies based on prior in vitro and in vivo antiparasitic and antiviral studies and highlights the need for further research and investment in this area. In terms of mosquito-borne diseases, paratransgenesis strategies have been developed to target Plasmodium. We postulate the potential to apply this principle to target arboviruses using antiviral toxin effectors.

Background: Pharmacists need up-to-date knowledge and decision-making support in HIV care. We aim to develop MARVIN-Pharma, an adapted artificial intelligence-based chatbot initially for people with HIV, to assist pharmacists, considering evidence-based needs. Methods: From Dec 2022 to Dec 2023, an online needs-assessment survey evaluated Québec pharmacists' knowledge, attitudes, involvement, and barriers relative to HIV care, alongside perceptions relevant to the usability of MARVIN-Pharma. Recruitment involved convenience and snowball sampling, targeting National HIV and Hepatitis Mentoring Program affiliates. Results: Forty-one pharmacists (28 community, 13 hospital-based) across 15 Québec municipalities participated. Participants perceived their HIV knowledge as moderate (M=3.74/6). They held largely favorable attitudes towards providing HIV care (M=4.02/6). They reported a “little” involvement in the delivery of HIV care services (M=2.08/5), most often ART adherence counseling, refilling, and monitoring. The most common barriers reported to HIV care delivery were a lack of time, staff resources, clinical tools, and HIV information/training, with pharmacists at least somewhat agreeing that they experienced each (M≥4.00/6). On average, MARVIN-Pharma's acceptability and compatibility were in the ‘undecided’ range (M=4.34, M=4.13/7, respectively), while pharmacists agreed to their self-efficacy to use online health services (M=5.6/7). Conclusion: MARVIN-Pharma might help address pharmacists' knowledge gaps and barriers to HIV treatment and care, but pharmacist engagement in the chatbot’s development seems vital for its future uptake and usability.

COX II containing a dual core CuA active site is one of the three core subunits of mitochondrial Cco, which plays a significant role in the physiological process. In this report, the full-length cDNA of COXⅡ gene was cloned from Sitophilus zeamais, which had an ORF of 684 bp encoding 227 amino acids residues. The predicted COXⅡ protein had a molecular mass of 26.2 kDa with pI value of 6.37, and multiple sequence alignment and phylogenetic analysis indicated that Sitophilus zeamais COXⅡ had high sequence identity 78.51% with the COXⅡ of other insect species, especially similarity to sitophilus oryzae. This gene was subcloned into the prokaryotic expression vector pET-32a, and induced by IPTG in E.coli Transetta (DE3) expression system. Finally the COXⅡ with 6-His tag was purified using affinity chromatography with Ni²⁺-NTA agarose. WB showed the recombinant COXⅡ was about 44 kD, and the concentration of fusion protein was 50μg/mL. UV-spectrophotometer and infrared spectrometer analysis showed that recombinant COXⅡ could catalyze the oxidation of substrate Cytc, and influenced by AITC. It was found that AITC could form a hydrophobic region with COXⅡ protein via molecular docking, besides, a sulfur atom of AITC structure could form a length of 2.9 Å hydrogen bond with Leu-31. These results will provide valuable information for elucidating the role of COXⅡ in Sitophilus zeamais responses to AITC, meanwhile, it will helpful to carry out a point mutation in AITC binding sites for the future research.

Insulin-like Growth Factor 2 mRNA binding Protein 1 (IGF2BP1) is a promising candidate gene for influencing economic traits in livestock and poultry. The second intronic region of IGF2BP1 is closely related to growth traits, although the exact mechanism remains unclear. The preliminary resequencing results of goats in our laboratory demonstrated that the IGF2BP1 gene region was subject to strong selection, then we selected multiple single nucleotide polymorphisms (SNPs) to identify. Seven SNPs were located in the conserved region of the second intron, and their functions and relationship with growth traits require further clarification. This study selected 348 Nanjiang Yellow goats as experimental subjects, and chose Time of Flight Mass Spectrometer (MALDI-TOF) as the main method. Our results showed that six SNPs were significantly correlated with the growth traits of the Nanjiang yellow goat by association analysis. Among them, the rs652062749(A>G) was identified as the primary locus affecting the later stage of growth traits of Nanjiang yellow goat. Moreover, there was a strong linkage among three SNPs, and the rs638185407 (T>A) mutant type was observed to increase the luciferase activity in H293T cells extremely significantly. The TTAACT, TTCCCC, and ATCACT combination genotypes were dominant combination genotypes, which provided theoretical references for further genetic co-breeding. The results of our study demonstrate the potential role of the IGF2BP1 gene as a functional genetic marker in the breeding programs of Nanjiang Yellow goats.

The objectives of the study were to determine the spatial rate of CO₂ flux (Net Ecosystem Exchange) and soil moisture in a wetland ecosystem applying Sentinel-1 IW (Interferometric Wide) data of VH (Vertical Transmit/Horizontal Receive—cross polarization) and VV (Vertical Transmit/Vertical Receive—like polarization) polarization. In-situ measurements of carbon flux, soil moisture, and LAI (Leaf Area Index) were carried out over the Biebrza Wetland in north-eastern Poland. The impact of soil moisture and LAI on backscattering coefficient (σ°) calculated from Sentinel-1 data showed that LAI dominates the influence on σ° when soil moisture is low. The models for soil moisture have been derived for wetland vegetation habitat types applying VH polarization (R² = 0.70 to 0.76). The vegetation habitats: reeds, sedge-moss, sedges, grass-herbs, and grass were classified using combined one Landsat 8 OLI (Operational Land Imager) and three TerraSAR-X (TSX) ScanSAR VV data. The model for the assessment of Net Ecosystem Exchange (NEE) has been developed based on the assumption that soil moisture and biomass represented by LAI have an influence on it. The σ° VH and σ° VV describe soil moisture and LAI, and have been the input to the NEE model. The model, created for classified habitats, is as follows: NEE = f (σ° Sentinel-1 VH, σ° Sentinel-1 VV). Reasonably good predictions of NEE have been achieved for classified habitats (R² = 0.51 to 0.58). The developed model has been used for mapping spatial and temporal distribution of NEE over Biebrza wetland habitat types. Eventually, emissions of CO₂ to the atmosphere (NEE positive) has been noted when soil moisture (SM) and biomass were low. This study demonstrates the importance of the capability of Sentinel-1 microwave data to calculate soil moisture and estimate NEE with all-weather acquisition conditions, offering an important advantage for frequent wetlands monitoring.

Extracting entities from large volumes of chicken epidemic texts is crucial for knowledge sharing, integration, and application. However, Named Entity Recognition (NER) encounters significant challenges in this domain, particularly due to the prevalence of nested entities and domain-specific named entities, coupled with a scarcity of labeled data. To address these challenges, we compiled a corpus from 50 books on chicken diseases, covering 28 different disease types. Utilizing this corpus, we developed a nested NER model, MFGFF-BiLSTM-EGP. This model integrates the Multiple Fine-Grained Feature Fusion (MFGFF) module with a BiLSTM neural network and employs an Efficient Global Pointer (EGP) for predicts the entity location encoding. In MFGFF module we designed three encoders, character encoder, word encoder and sentence encoder, this design effectively captures fine-grained features and improves the recognition accuracy of nested entities. Experimental results show that the model performs robustly, with F1 scores of 91.98%, 73.32%, and 82.54% on the CDNER, CMeEE V2, and CLUENER datasets, respectively, outperforming other commonly used NER models. Specifically, on the CDNER dataset, the model achieved an F1 score of 79.68% for nested entity recognition. This research not only advances the development of knowledge graph and intelligent question-answering system for chicken diseases but also provides a viable solution for extracting disease information that can be applied to other livestock species.

Performing optimisation and scale-up studies of crystallisation systems requires accurate and computationally efficient mathematical models. The assumption of the ideal mixing conditions in batch reactors typically produce inaccurate results while the computational expense of CFD models is still prohibitively high. Therefore, in this work, a new intermediary approach is proposed that takes into account the non-ideal mixing conditions in the reactor and requires less computational resources than full CFD simulations. Starting with the Danckwerts concept of the intensity of segregation, an analogy between its application to chemical reactions and the kinetics of the crystallisation phenomena (such as nucleation and growth) has been made. As a result, the modified kinetics expressions have been derived which incorporate the effect of non-idealities present in stirred reactors. This way, based on the experimental measurements of the mixing time using the Laser Induced Fluorescence (LIF) technique, computationally more efficient mathematical models can be developed in two ways: (1) the accurate semi-empirical correlations are available for standard mixing configurations with the most often used types of impellers, (2) CFD simulations can be utilised for estimation of the mixing time; in this case it is necessary to simulate only the mixing process. The benefits offered by the LIF experimental technique have been demonstrated and some frequent problems in its application analysed. The mixing time results for configurations with and without baffles for three types of impellers and four different rotational speeds have been presented. The false shorter mixing times in the non-baffled configurations have been observed and this phenomena explained by the existence of two segregated zones in the reactor and confirmed by additional experiments. The precise measurements in these cases have been shown as difficult using the LIF technique, particularly for higher rpms. The experimental data has been compared to the preliminary simulation results obtained from the Smoothed Particle Hydrodynamics method and the standard k-ε turbulence model with the modest success. The shortcomings of the SPH model have been recognized and the directions for the future work discussed.

Stress is a natural yet potentially harmful aspect of human life, necessitating effective management, particularly during overwhelming experiences. This paper presents a scoping review of personalized stress detection models using wearable technology. Employing the PRISMA-ScR framework for rigorous methodological structuring, we systematically analyzed literature from key databases including Scopus, IEEE Xplore, and PubMed. Our focus was on biosignals, AI methodologies, datasets, wearable devices, and real-world implementation challenges. The review presents an overview of stress and its biological mechanisms, details the methodology for the literature search, and synthesizes the findings. It shows that biosignals, especially EDA and PPG, are frequently utilized for stress detection and demonstrate potential reliability in multimodal settings. Evidence for a trend towards deep learning models was found, although the limited comparison with traditional methods calls for further research. Concerns arise regarding the representativeness of datasets and practical challenges in deploying wearable technologies, which include issues related to data quality and privacy. Future research should aim to develop comprehensive datasets and explore AI techniques that are not only accurate but also computationally efficient and user-centric, thereby closing the gap between theoretical models and practical applications to improve the effectiveness of stress detection systems in real scenarios.

The European Union's recent decision to renew the authorization for the use of glyphosate until 15 December 2033 stimulates the scientific discussion all around the world regarding its toxicity or otherwise for humans. Glyphosate is a chemical used by millions of tons in the last 50 years worldwide to drying weeds in cultivated fields, greenhouses, roadsides. Concern has been raised in many quarters about the possible presence in the food chain and the consequent adverse effects on health: both aspects that argue in favor of toxicity and those that instead may indicate limited toxicity of glyphosate are here discussed. The great debate that has been generated requires further investigations and field measurements to understand its fate once dispersed in the environment and its concentration in the food chain. Hence the need for validated analytical methods that are available to analysts in the field. In the present review, methods for the analytical determination of glyphosate and its main metabolite, AMPA, are discussed, with a specific focus on chromatographic techniques applied to cereal products. The experimental procedures are explained in any detail, including cleanup, derivatization, and instrumental conditions to give the laboratories involved enough information to proceed with the implementation of this line of analysis. The prevalent chromatographic methods used are LC-MS/MS, GC-MS/SIM, and GC-MS/MS but sufficient indications are also given to those laboratories that wish to use the simpler HPLC-FLD, HPLC-UV, GC-NPD or GC-FPD techniques for screening purposes. Concentrations from literature measured in wheat, corn, barley, rye, oats, soybean, and cereal-based foods are reported together with the regulatory status in various parts of the world and the accumulation mechanism. As for the accumulation in cereals, available data show that glyphosate tends to accumulate more in wholemeal flours than in refined ones, that its concentration in the product strictly depends on the treatment period (the closer it is to the time of harvesting, the higher the concentration) and that in cold climates the herbicide tends to persist in the soil for a long time.

(1) Background: The aim of the work was to characterize the climatic evolution and change based on the Multi Criteria Classification through the dynamics of bioclimatic indices in viticulture across Italy and its regional administrative boundaries, focusing on latitudes and elevations. (2) Methods: The impact of climate change on viticulture in Italy was analysed and spatialized with reference to historical data from 1991 to 2021 and to the Future Scenarios up to 2080 assumed by SSP2-4.5 and SSP5-8.5, taking into account 13 GCMs. (3) Results: The bioclimatic indices have all shown a significant trend in the historical period, with an increase in temperature and a decrease in precipitation, reflecting their effects on the entire Italian territory with respect to HI, up to 44°N for CI and up to 46°N for DI, regardless of altitude. The Future Scenarios highlighted a shift towards the warmer classes of the two temperature-based indices (HI and CI) for both SSPs, especially for altitudes up to 900 m a.s.l.. The DI-based classification based on DI remained relatively stable in Italy over time, although DI values will become increasingly negative in the near future. (4) Conclusions: The climate in Italy is warming, especially in the south and in the coastal regions. By 2080, more areas will be “Very Hot” with “Warm Nights.” Drought will also increase and have a negative impact on viticulture. The importance of higher latitudes and altitudes in mitigating the effects of climate change justifies the continuing trend towards the relocation of vineyards as a medium-term solution and as an alternative to targeted cultivation methods that must be adopted in the short-term to safeguard the suitability of an area to quality viticulture.

As a precious natural resource, forests are being destroyed. In previous studies, there is a lack of interactive assessment of its distribution that comprehensively considers multiple external disturbances. This paper takes the Barcelona Metropolitan Region as an example. Based on remote sensing, it analyzes the development process of the forest from 2006 to 2018 through multiple landscape indicators, and OLS models were established to analyze variables that have direct and indirect effects on forest distribution. In addition, the ecological structure of the forest was analyzed based on NDVI. It was found that the forest area is the largest but has been decreasing, becoming more complex in distribution structure. Much of the forest was converted to agricultural land and grassland. The green quality of forests was increasing, and the broad-leaved forest, the second largest area, contributes the most. NDVI is the most important positively correlated variable, and daytime surface temperature is an important inverse factor related to NDVI. In addition, NDBI is also a negative condition that inhibits forest development. In conclusion: The BMR forest area is decreasing and becoming more fragmented. NDVI and daytime LST are the two most significant factors. Climate warming may lead to worse forest development.

Back-care knowledge and behaviour may play a vital role in preventing musculoskeletal current and future discomfort and injuries. The aim of the current survey was to explore the level of knowledge regarding ergonomics and posture together with postural behaviour and the incidence of musculoskeletal pain (MSP) in university students in the northeast of England. A mixed methods survey was conducted on a convenience sample of 55 university students. The 32-item valid and reliable questionnaire contains questions on socio-demographics, MSP, knowledge regarding ergonomics and posture (8 closed ended and 8 open-ended items) as well as postural behaviour. Nearly 1.8%, 20% and 78.2% of the university students had poor, fair and good knowledge of ergonomics and posture respectively. Among the 37 students who carried a backpack, 51.4% were found to have poor postural behaviour, 37.8% had fair behaviour and 10.8% had good postural behaviour. Of the 18 students who did not carry a backpack, 55.6% were found to have poor postural behaviour, 27.8% had fair behaviour and 16.6% had good postural behaviour. 70.9% of the students experienced MSP with the most prevalent site of pain being the lower back region. The key themes that emerged from qualitative data (8 open-ended questions) were: “Comfortable posture”, “Correct spinal alignment”, “Spine support”, “less pain and injuries”, “Use knees not the back”, “Keep the object close to body”, “Hands on desk”, “Feet flat on floor” as well as “eyes at screen level”. The findings of this study can be used to develop targeted interventions aimed at educating university students about ergonomics and posture in order to prevent the incidence of MSP. Future research in this field with a large and more representative sample of the university students’ population is strongly recommended to fully understand their knowledge of ergonomics and posture, postural behaviour as well as incidence of MSP.

The design complexity of the new generation of civil aero-engines results in higher demands on engines’ components, higher component temperature, higher heat generation, and, finally, critical thermal management issues. This paper will propose a methodological approach to create physics-based models for heat loads developed by sources as well as a systematic sensitivity analysis to identify the effects of design parameters on the thermal behaviour of civil aero-engines. The ranges and levels of heat loads generated by heat sources (e.g., accessory gearbox, bearing, pumps, etc.) and heat absorption capacity of heat sinks (e.g., engine fuel, oil, and air) are discussed systematically. The practical research challenges for thermal management system design and development for the new and next generation of turbofan engines will then be addressed through a sensitivity analysis of the heat load values as well as the heat sinks flow rates. The potential solutions for thermal performance enhancements of propulsion systems will be proposed and discussed accordingly.

The multi-stage, multi-level assembly job shop scheduling problem (MsMlAJSP) is commonly encountered in the manufacturing of complex customized products. Ensuring production efficiency while effectively improving energy utilization is a key focus in the industry. For the energy-efficient MsMlAJSP (EEMsMlAJSP), an improved imperialist competitive algorithm based on Q-learning (IICA-QL) is proposed to minimize the maximum completion time and total energy consumption. In IICA-QL, a decoding strategy with energy-efficient triggers based on problem characteristics is designed to ensure solution quality while effectively enhancing search efficiency. Additionally, an assimilation operation with operator parameter self-adaptation based on Q-learning is devised to overcome the challenge of balancing exploration and exploitation with fixed parameters, thus the convergence and diversity of the algorithmic search is enhanced. Finally, the effectiveness of the energy-efficient strategy decoding trigger mechanism and the operator parameter self-adaptation operation based on Q-learning is demonstrated through experimental results, and the effectiveness of IICA-QL for solving EEMsMlAJSP is verified by comparing with other algorithms.

Iron metabolism plays a crucial role in the management of hemoglobinopathies, particularly in conditions such as β-thalassemia and sickle cell anemia (SCA). This paper describes the mechanisms of iron overload in patients with transfusion-dependent thalassemia (TDT), non-transfusion-dependent thalassemia (NTDT), and SCA, highlighting the distinct paths leading to iron accumulation in each condition. The primary focus of this review article is on the role of genetic modifiers influencing iron metabolism and the variability in iron overload presentation among patients. Genetic mutations in genes such as HFE, HAMP, TFR2, SLC40A1, and others significantly impact iron regulation. These modifiers can exacerbate or ameliorate iron overload, and understanding these genetic factors is important for explaining the diverse disease severity and differences in the mechanism and clinical presentation of iron overload in these patients. The ongoing INHERENT study aims to further elucidate the influence of these genetic modifiers through a comprehensive genome-wide association study, potentially leading to novel therapeutic interventions for managing iron homeostasis in hemoglobinopathy patients.

The research reported on this paper was aimed at improving the overall efficiency of a PDO certified artisanal cheese production process. Being a PDO certified foodstuff by the EU, it is considered to have properties and qualities determined by the geographical environment in which is made, with its production taking place in a specific and determined geographical location, in this case the Serra da Estrela region. In that sense, the authors conducted a mapping according to a systemic perspective of the processes involved in the context of manufacturing and distribution of certified Serra da Estrela cheese. Numerous methods were used throughout the process, such as a systemic design analysis, and techniques derived from ethnographic methods, which led to the collection of data in the field and consequently provided the immersion of the researcher in genuine work situations. Critical points were identified and emphasized in the systemic map with the purpose of encouraging initiatives to address and overcome the gaps and inefficiencies detected. The systemic design analysis triggered the development of design work. Observations following an ethnographic approach identified ergonomic risks in cheese making during the process of cutting excess chips, fostering the emergence of musculoskeletal disorders at the wrist. A tool that fits best to the task at hand was developed. A prototype of the new tool enabled collecting feedback from use in the work context, in order to inform product development. The domains of agricultural production and microbiology, considering the specific microorganisms developed trough the ripening process of the cheese, turned out to be aspects of high importance for the issue under focus, contributing to a broader understanding of the ripening process and its risks, simultaneously improving the efficiency and success of cheese production. If it were not for the systemic analysis, which served as a link between the boundaries of distinct domains such as the risk of microorganism contamination, ergonomics, energy efficiency, legislation and regulation policies, transportation challenges and economic viability, approached throughout the research. Simultaneously creating bridges between them, the various problems might not have been detected in the first place, as they are usually addressed in specialized disciplines, predetermined by the restrictions of each specific area of knowledge. As a consequence of the development of this research, which was based on an analysis that sought to establish possible connections between various disciplines and tried to constantly maintain a holistic perspective, making new connections and observing the issues from a new angle, apart from the already established methodologies. All this allowed to lay out the seeds for the development of a plan to tackle the critical points identified by the systemic analysis reported in this paper.

Groundwater pollution in intensive horticultural areas is becoming an increasingly important problem. Therefore, this study evaluates nitrogen (N) fertilization in open field processing pepper crop in Extremadura, Spain. Previous research on the effect of N on sweet peppers grown in greenhouses is abundant, but data on outdoor cultivation, especially considering variety and site influences, are lacking. Field trials were conducted in 2020, 2021 and 2022 to determine the opti-mum N fertilizer rate for processing peppers, with the aim of reducing environmental impacts such as nitrate leaching while maintaining crop yields. Different N rates were applied in the trials, ranging from no N fertilizer to 300 kg N/ha. Meas-urements included crop yield, biomass, intercepted photosynthetically active radiation (PAR), and canopy cover. The study also developed a critical nitrogen curve (CNC) to determine the minimum N concentration required for optimal growth. The results showed that applying more than 200 kg N/ha did not significantly increase yield. Nitrogen-free treatments resulted in earlier fruit maturity, concentrating the harvest and reducing waste. In addition, excessive N application led to envi-ronmental problems such as groundwater contamination due to nitrate leaching. The study concludes that outdoor pepper crops in this region can achieve optimal yields with lower N rates (around 120 kg N/ha) compared to current practices, thereby reducing environmental risks and fertilizer costs. It also established relationships between biomass, canopy cover, and N uptake to improve fertilization strategies. These data support future crop modelling and sustainable fertili-zation practices.

Semi-Interlocking Masonry (SIM) represents an innovative building system developed at the Centre for Infrastructure Performance and Reliability at The University of Newcastle, Australia. This system employs a unique approach to interlocking mortar-less engineered masonry panels constructed from SIM units. These units are designed to offer substantial energy dissipation capacity, primarily attributed to the friction occurring on the sliding bed joints between the units within the panel during seismic events. The primary aim of this study is to evaluate the viability of incorporating semi-interlocking masonry as infill panels in the construction of multi-storey buildings across diverse geographical locations with varying seismic conditions in Australia. To assess the feasibility of SIM panels in different conditions (according to Australian Standard AS1170) in Australia, a comprehensive analysis using Strand7 is conducted on a three-storey structure incorporating traditional masonry infill panels and SIM panels. The comparison of displacement and base shear capacities is carried out in response to seismic events across various scenarios in different locations within Australia. The insights gained from this comparative analysis contribute valuable information regarding the viability of implementing SIM as a contemporary construction material.

The fatty acid composition, biophenol, tocopherol, sterol and triterpenic dialcohol content and composition of the autochthonous Slovenian olive varieties 'Buga', 'Črnica' and 'Drobnica' were studied during a three-year period with the aim to valorise the characteristics of the three olive varieties. Standardized and accredited analytical methods were applied. The results of the investigation showed that the highest average amount of oleic acid (75.75%) was determined in oils of the variety 'Črnica', followed by 'Drobnica' (72.06%) and 'Buga' (68.73%). All the three varieties are a good source of total biophenols ('Buga' 616 mg/kg, 'Drobnica' 569 mg/kg and 'Črnica' 427 mg/kg) and α-tocopherol ('Buga' 378 mg/kg, 'Drobnica' 279 mg/kg and 'Črnica' 243 mg/kg). 'Buga' and 'Drobnica' are characterised by high amounts of total sterols, 2468 mg/kg and 2391 mg/kg, respectively, 'Črnica' oils, in comparison, showed a lower average value of total sterols (1351 mg/kg). The acquired data of the autochthonous Slovenian olive varieties 'Buga', 'Črnica' and 'Drobnica' are very important to valorise the characteristics of the produced oils. The studied varieties showed a great potential for further cultivation and valorisation of the traditional olive oil production of the region and are important for preserving the biodiversity and tradition of the territory.

Psoriasis is a lifelong, systemic, immune mediated inflammatory skin condition, affecting 1-3% of the world’s population, with an impact on quality of life similar to diseases like cancer or diabetes. Genetics are the single largest risk factor in psoriasis, with GWAS studies showing that many psoriasis risk genes lie along the IL23/Th17 axis. Potential psoriasis risk genes determined through GWAS can be annotated and characterised using functional genomics, allowing the identification of novel drug targets and the repurposing of existing drugs. The pathogenesis of psoriasis is complex and focusing on the IL23/Th17 axis can provide insight into key cell types, cytokines and intracellular signaling pathways involved. Examination of currently available biological treatments, time to relapse post drug withdrawal and rates of drug primary/secondary drug failure show the need for greater understanding of the underlying genetic mechanisms of psoriasis and how they can impact treatment. This could allow for patient stratification towards the treatment most likely reduce dis-ease burden for the longest period possible.

Emerging infectious diseases are a major threat to biodiversity and an important public health issue. West Nile virus (WNV) is an emerging vector-borne zoonotic arbovirus that is currently broadening its distribution in Europe. The evidence of WNV circulating in resident and migratory species has implications for both animal and public health, and should therefore be studied in depth. An integrated surveillance program, namely in birds, is essential for reducing the risk of infection in human populations within the One Health principles. In the present study, wild birds admitted to wildlife rehabilitation centres in Portugal were sampled. Two-hundred and eight blood samples were assayed serologically to antibodies to WNV, by using a commercial ELISA kit. An overall seroprevalence of 19.6% (95% confidence interval [CI]: 13.7-26.7%) was observed. Antibodies to WNV were detected in 13 (35.1%) different species of wild birds. Accipitriformes (26.7%; 95% CI: 18.5-36.2%) and Strigiformes (26.7%; 95% CI: 14.6-42.0%) were the orders with the highest seroprevalence recorded. There were no statistically significant differences (p = 0.725) between the geographical regions (NUTS II) studied, but statistically significant difference (p = 0.017) was found between gender (male: 34.4%; female: 4.8%). A higher seroprevalence was found in adults (32.1%) compared to juvenile birds (9.3%) (p = 0.014), and age was considered a risk factor to WNV infection in wild birds (odds ratio 1.4; 95% CI: 0.5–4.0). More epidemiological studies are needed in Portugal, since the actual spread of the WNV throughout the country is unknown.

Pelagic stingray (Pteroplatytrygon violacea) is the only species of stingray (Dasyatidae) that utilizes both pelagic and demersal habitats. It is the main bycatch species in pelagic longline fisheries targeting bluefin tuna in the Gulf of Lions. In the Mediterranean Sea, their stock structure, behavioural ecology and movements are unknown. For the first time in the Mediterranean, 17 individuals (39 to 60 cm disc width) were tagged with pop-up satellite archival transmitting tags using a novel method of tag attachment, to investigate horizontal and vertical movements. The tags were attached for between two and 60 days. Between the months of July and October, pelagic stingray occupied a temperature range of 12.5 to 26.6°C, and a depth range extending from the surface to 480 m. Monthly trends in catch-per-unit-effort (CPUE) of pelagic stingray peaked in August and decreased by late autumn. Pelagic stingray may aggregate on the continental shelf during summer, and move southwards in early autumn, and this movement pattern is considered in relation to the reproductive cycle and overwintering. Future work and options for bycatch mitigation are discussed.

Effective and rapid mixing is essential for various chemical and biological assays. The present work reports a simple and low-cost micromixer based on magnetofluidic actuation. The device takes advantage of magnetoconvective secondary flow, a bulk flow induced by an external magnetic field, for mixing. A paramagnetic stream of diluted ferrofluid and a non-magnetic stream are introduced to a straight microchannel. A permanent magnet placed next to the microchannel induced a non-uniform magnetic field. The magnetic field gradient and the mismatch in magnetic susceptibility between the two streams create a body force, which leads to rapid and efficient mixing. The micromixer reported here could achieve a high throughput and a high mixing efficiency of 90 % in a relatively short microchannel.

Amuyo Ponds (AP) are a group of three hydrothermal lagoons located at 3,700 m above sea level, in a pre-Andean setting at the Atacama Desert. Each pond shows a conspicuous green, red, or yellow coloration, and discharge waters rich in arsenic and boron into the Caritaya River (Camarones Basin, Arica and Parinacota Region, in northern Chile). Microorganisms at these ponds are subjected to harsh environmental conditions, and microbial composition and diversity in Amuyo Ponds sediments are unknown. Then, microbial life colonizing AP sediments was explored by metagenomics analyses. This approach showed a highly diverse microbial life dominated by members of the Bacterial Domain (nearly 800 bacterial genome sequences) and includes sequences associated to Archaea, Eukarya, and viruses. We also report putative functional capabilities related to virulence and defense genes, and biosynthesis of secondary metabolites. Thirteen bacterial and fourteen virus metagenome-assembled genomes were reconstructed and are here informed. This work expands our knowledge on the richness of microorganisms in AP and open further studies on the ecology and genomics of this striking Andean geosite.

Parental labour migration, either one or both parents, has been associated with various challenges among left-behind children (LBC). However, there is a limited understanding of the LBC’s own views and experiences of social and mental wellbeing and how the new daily life circumstances they encounter following their parents’ migration impact them. This study aimed to understand the influence of parental migration and its aftermath on the social and mental wellbeing of children and adolescents (referred to as LBC) in two rural districts in Indonesia. Employing a qualitative design, data were collected through individual in-depth interviews with LBC (n=24) aged 14 to 18 years, recruited using the snowball sampling technique. Data were thematically analysed, guided by a qualitative data analysis framework. The findings showed that parental migration negatively impacted the social wellbeing of LBC. This impact was reflected in negative labelling from friends and changes in familial roles which influenced their social interactions and activities with peers. Parental migration also caused challenges to the mental wellbeing of LBC. These manifested in the LBC experiencing fractured emotional bonds, leading to negative emotions, including stress, anxiety, sadness, depression, frustration, loss of motivation, and self-imposed isolation, which were associated with their parents’ migration and abrupt disruptions in parent-child communication. The transition to new life situations with caregivers after parental migration and the dynamics within the caregivers’ households were additional factors that detrimentally affected their mental well-being. Unmet basic needs and educational needs due to financial hardships faced by mothers and caregivers, further exacerbated mental health challenges for the children. The findings indicate the importance and improvement of policies and interventions in Indonesia (e.g., counselling services, non-cash food assistance, family hope program, direct cash assistance) that cover and address the diverse needs of mothers or caregivers and the LBC.

Fires constitute a significant threat due to the pollutants emitted and the destruction they cause. People who take part in fire-fighting operations must be equipped with appropriate tools, including special clothing that will allow them to work and guarantee safety. One of the threats are compounds from the PAH group, which are characterized by high toxicity and carcinogenicity. Therefore, it is important that the materials used constitute a barrier to contamination. Various materials from which individual elements of special firefighter's clothing are made were tested. Additionally, the importance of height on the possibility of sorption of PAH compounds on a given type of material was analyzed. Based on the results obtained, it was found that the type of material and the zone in which the clothing items are used are important in the sorption processes of pollutants. Data in this area may be important for taking further actions regarding the modification of materials used in special fire brigade clothing and in their cleaning processes.

Hazelnut shells (HS), scientifically known as Corylus avellana L. shells, are a waste produced in companies that process nuts. The main objective of this study was to find an efficient way to maximize the chemical potential of HS by solubilizing the hemicelluloses, which could then be used to recover sugars and at the same time increase the lignin content of this material in order to produce adhesives or high strength foams. In order to optimize the pre-hydrolysis process, two different temperatures (160 and 170 C) and times varying from 15 to 180 min were tested. All the remaining solid materials were then liquefied by polyalcohols with acid catalysis. The chemical composition of hazelnut shells was determined before and after the pre-hydrolysis. All the process was monitored by FTIR-ATR by determining the spectra of solids and liquids after pre-hydrolisis and liquefactions steps. The highest solubilization of hazelnut shells was found for 170 C and 180 min, resulting in a 25.8% solubilization. Chemical analysis after the hydrolysis process showed a gradual increase in the solubilization of hemicelluloses as both the temperature and time of the reactor were increased. Simultaneously, the percentages of α-cellulose and lignin in the material also increased with rises in temperature and duration. FTIR-ATR allowed for the detection of significant spectral changes in the hazelnut shells from their initial state to the solid residue and further into the liquefied phase. This confirmed that pre-hydrolysis was effective in enhancing the chemical composition of the material, making it more suitable for the production of adhesives or polyurethane foams with enhanced mechanical strength.

Introduction: The COVID-19 pandemic challenged people with spinal cord injury (SCI) regarding a variety of mental and physical issues. New challenges may arise as the effects of the pandemic continue. The objective of the present study was to explore the social participation of Canadians with SCI during the second wave of COVID-19. Methods: Participants with SCI from two Canadian provinces (Quebec and British Columbia) were interviewed. Results: Eighteen participants completed interviews. Facilitators of social participation remain similar since the first wave of COVID-19, such as the use of technology, help received by relatives and the use of delivery services to obtain groceries and other essentials. Obstacles to mobility due to winter conditions and lack of considerations related to COVID-19 public health measures specific to wheelchair users were also discussed by participants. Conclusions: People with SCI perceived participation restrictions, little changes in life habits, and uncertainty about the future during the second wave of COVID-19. The unique living conditions of people with SCI, ability to adapt life habits, and the lived experiences of people with SCI may have contributed to an overall resilience during the pandemic. Adaptive families, social contacts and technology made a difference during the pandemic.

This paper presents the novel development of a shape memory polymer foam based on polymer-polymer nanocomposites. Herein, polylactide (PLA)/biosourced polyamide (PA) foams are fabricated by in-situ fibrillation of polymer blends and subsequent supercritical CO2 foaming technique. In this system, PLA serves as a shape memory polymer to endow this foam with a shape memory effect (SME), and in-situ generated PA nanofibers are employed to reinforce the PLA cell walls and provide an additional permanent phase. Concentration of PA, 5 wt.%, is chosen to form an entangled nanofibrillar network. Foams of PLA/PA nanoblends with the same content of constituents are fabricated to reveal the effect of minor phase morphology on the cell structure and shape memory behavior of polymer foams. Profiting from the reinforcing effect of PA nanofibers, the PLA/PA nanocomposite foam exhibits smaller foam cells, a narrower cell size distribution and a comparable cell concentration than the PLA/PA nanoblend foam. In addition, PA nanofibers, unlike PA nanodroplets, favor the shape fixation ratio and recovery ratio and shorten the shape recovery time.

Our article AI, cultural heritage and bias examines the challenges and potential solutions for using machine learning to interpret and classify human memory and cultural heritage artifacts. We argue that bias is inherent in cultural heritage collections (CHCs) and their digital versions, and that AI pipelines may amplify this bias. We hypothesise that effective AI methods require vast, well-annotated datasets with structured metadata, which CHCs often lack due to diverse digitisation practices and limited interconnectivity. The paper discusses the definition of bias in CHCs and other datasets, exploring how it stems from training data and insufficient humanities expertise in generative platforms. We conclude that scholarship, guidelines, and policies on AI and CHCs should address bias as both inherent and augmented by AI technologies. We recommend implementing bias mitigation techniques throughout the process, from collection to curation, to support meaningful curation, embrace diversity, and cater to future heritage audiences.

A previous research showed the 1755 tsunami would inundate the Marginal Avenue, the railway and the low ground area of Caxias, Oeiras municipality, Portugal. Thus, in this study several proposals for coastal protection are presented. A new Lidar data of local topography allowed the construction of a more accurate DEM, including the representation of the streets of Caxias downtown, to be used in the tsunami numerical model. The results were combined with field survey on Caxias and other coastal areas of Portugal and Japan. The new calculations show the low ground areas up to 6 m in height area inundated by the tsunami. However, with the new proposal DEM the tsunami inundation is restricted to the beaches. The proposal includes the construction of a new sea wall with 7 m in height at Caxias beach, the increase in height of the Barcarena Stream levees and the elevation of the sidewalk at São Bruno beach, with a gentle slope up to 7 m in height. It is also proposed the construction of a third bridge over the Barcarena Stream for pedestrian ranging from 5 to 7 m in height that will serve as a gate for the incoming tsunami waves.

The second article in the series presents the application of the Smoothed Particle Hydrodynamics (SPH) method to modelling of batch crystallisation in stirred tanks. A methodology to integrate the population balance equations (PBE) in parallel and independently from the Navier-Stokes equations is demonstrated. The benefits of the proposed methodology in terms of computational requirements, accuracy and availability of the crystal size distribution are discussed. The specific formulation of the SPH equations where the resulting system of ordinary differential equations is solved using the weighted contributions rather than numerically by solving a linear system of equations allows for massive parallelisation and a very loose coupling of the population balance and the fluid dynamics. It has been demonstrated, that the population balance equations can be solved on a Shared Memory Architecture (SMA) system using the OpenMP interface while the fluid dynamics equations being computed independently on a General Purpose Graphics Processing Unit (GPGPU) using the NVidia CUDA technology. This way, a significant portion of the computational overhead due to the large number of additional transport equations resulting from the discretisation of the population balance was removed: the SPH simulation coupled with 200 population balance equations was only 40% slower compared to SPH-only simulation. Two methods for the solution of population balance equations that preserve full crystal size distribution were implemented: discretised population balance (DPB) and method of characteristics (MOCH). The DPB equations are solved using the high-resolution finite-volume method with flux limiter and the effect of a large number of different flux limiters have been investigated. Both methods were validated using the case studies from the literature where an analytical solution can be derived. The developed models were applied to a numerical solution of coupled computational fluid dynamics and population balance equations to model a batch crystallization process. The effect of the hydrodynamics on the local temperature/supersaturation and the resulting crystal size distribution was captured and compared to the ideal mixing case. The simulation results from the DPB and MOCH methods were compared in terms of computational requirements and accuracy and MOCH selected as computationally more efficient and accurate.

Microplastic pollution (MP) in marine environments around the globe is severe and enough precautions have not been taken so far for its prevention. The focus of this study is to quantify MPs from beach sediment and seawater samples and to identify their distribution and types along the western coast of Sri Lanka from the Kelani River estuary to the Mahaoya estuary. Nine sites along this 42 km stretch were selected and random sampling was employed to collect a minimum of 8 sediment samples from each site between October and December 2021. Water samples were also collected, parallel to the sediments, from the ocean surface. FTIR analysis revealed that most of the MPs found were polyethylene(PE), polypropylene(PP), polystyrene(PS), polyethylene terephthalate(PET), and phenol formaldehyde resin. The mean abundance of MPs varied from 2.0 ± 0.6 items/L to 161.0 ± 15.7 items/L in water samples and, from 3.0 ± 0.3 items/m2 to 656.0 ± 34.5 items/m2 in sediment samples. The MPs found were identified in different shapes as fragments (80.2%), pellets (14.9%), fibers (2.7%) and foams (2.5%). Analysis revealed that the beach sediments were contaminated with PS, phenol formaldehyde resin, PET, PP and PE, while surface seawater is dominated by phenol formaldehyde resin, PS, PP and PE.

The article offers a comprehensive overview of recent breakthroughs in eco-friendly polymers and polymer composites, underscoring their pivotal role in addressing sustainability challenges across diverse industrial sectors. Despite encountering obstacles related to performance and processability, biopolymers sourced from renewable materials emerge as promising alternatives for the plastics that are currently used by human beings. Natural fillers are highlighted as a strategic avenue for crafting sustainable composites, with residual natural fillers being particularly explored. Heightened environmental concerns propel discussions on the criticality of integrating biodegradable materials with natural fillers, underlining the urgency for clear frameworks and financial incentives to support adoption of these materials. Additionally, the article examines the potential of biodegradable polymers and polymer composites, with a specific emphasis on the utilization of polyhydroxyalkanoate (PHA) in composite materials and its market prospects. Moreover, it emphasizes the indispensable need for ongoing research and development endeavors to address environmental challenges within the polymer sector, reflecting a mounting interest in sustainable materials across industries.

Pulmonary hypertension (PH) is a serious condition linked to immune-system dysfunction. Myositis-specific/associated antibodies (MSA/MAA) play a role in idiopathic inflammatory myopathy (IIM) and interstitial lung disease (ILD), but their significance in PH remains unclear. We believe the presence of these antibodies, may be underestimated. This study analyzed adult PH patients without pre-existing IIM for MSA/MAA prevalence using a line-blot assay. We compared PH patients with and without ILD signs to a cohort clinically suspected of IIM/ILD (n=558). Our PH cohort (n=121) showed a significantly higher prevalence of overall weak positive MSA/MAAs and positive overlap syndrome-associated MAAs than the suspected IIM/ILD group (p

Background: This study assesses the effects of the ‘Radiant’ image enhancement technique on fetal nuchal translucency (NT) measurements during first trimester sonographic ex-ams. Methods: A retrospective analysis of 263 ultrasound images of first trimester midsagittal sections was conducted. NT measurements were obtained using a semi-automatic tool. Statistical methods were applied to compare NT measurements with and without ‘Radi-ant’ enhancement. An in-vitro setup with predefined line distances provided additional data. Results: Incremental increases in NT measurements were observed with varying levels of ‘Radiant’ application: An average increase of 0.19 mm with ‘Radiant min’, 0.24 mm with ‘Radiant mid’ and 0.30 mm with ‘Radiant max.’ The in-vitro results supported these findings, showing consistent effects on line thickness and measurement accuracy, with the smallest mean deviation occurring at the ‘Radiant mid’ setting. Conclusions: ‘Radiant’ image enhancement leads to significant increases in NT measure-ments. To avoid systematic biases in clinical assessments, it is advisable to disable ‘Radi-ant’ during NT measurement procedures. Further studies are necessary to corroborate these findings and to consider updates to the NT reference tables based on this technology.

Macrophages are well known for the involvement in the biocompatibility, as well as biodistribution, of nano(bio)materials. Although there are a number of rodent cell lines, they may not fully recapitulate primary cell responses; particularly for those of human cells. Isolation of tissue resident macrophages, from humans, is difficult and may result in insufficient cells with which to determine the possible interaction with nano(bio)materials. Isolation of primary human monocytes, and differentiation to monocyte-derived macrophages, may provide a useful tool with which to study, further, these interactions. To that end, we developed a standard operating procedure for this differentiation, as part of the REFINE project, and used it to measure the secretion of bioactive molecules from M1 and M2 differentiated monocytes in response to model nano(bio)materials, following an initial assessment of pyrogenic contamination which may confound, potential, observations. The SOP was deployed in two partner institutions with, broadly, similar results. The work presented here shows the utility of this assay but, highlights the relevance of donor variability in responses to nano(bio)materials. Whilst donor variability can provide some, logistical, challenges to application of such assays, this variability is much closer to the heterogeneous cells that are present in vivo, compared to homogeneous, non-human, cell lines.

Recent studies have demonstrated a relationship between poor vitamin D status and respiratory infections and diarrhea among young children. Acute lower respiratory infections (ALRI) and diarrhea are among the two most important causes of death in under-5 children. In this analysis, we examine the extent to which vitamin-D deficiency (<10 ng/ml) predicts these outcomes using data from a randomized controlled trial (RCT) of daily folic acid and/ or vitamin B12 supplementation for six months in 6 to 30 months old children conducted in Delhi, India. Of the 960 subjects who had vitamin-D concentrations measured, 331(34.5%) were vitamin-D deficient. We found, after controlling for relevant potential confounders (age, sex, breastfeeding status, wasting, stunting, underweight, anemia status at base line and season), the risk of ALRI was significantly higher among vitamin-D deficient (OR 1.26; 95% CI: 1.03 to 1.55) compared to vitamin-D-replete children in the six months follow-up period. Vitamin-D status was not significantly associated with episodes of diarrhea and clinical pneumonia. The extent of causal relationship of vitamin-D status and ALRI needs to be explored in further studies.

The Chikungunya virus (CHIKV) poses a significant global public health concern, especially in Africa. Since its first isolation in Tanzania in 1953, CHIKV has caused recurrent outbreaks, challenging healthcare systems in low-resource settings. Recent outbreaks in Africa highlight the dynamic nature of CHIKV transmission and the challenges of underreporting and underdiagnosis. Here, we review literature and analyze publicly available cases, outbreaks, and genomic data providing insights into the epidemiology, genetic diversity, and transmission dynamics of CHIKV in Africa. Our analyses reveal the circulation of geographically distinct CHIKV genotypes, with certain regions experiencing a disproportionate burden of disease. Phylogenetic analysis of sporadic outbreaks in West Africa suggests repeated emergence of the virus through enzootic spillover, which is markedly different from inferred transmission dynamics in East Africa, where the virus is often introduced from Asian outbreaks, including the recent reintroduction of the Indian Ocean lineage from the Indian subcontinent to east Africa. Furthermore, there is limited evidence of viral movement between these two regions. Understanding the history and transmission dynamics of outbreaks is crucial for public health planning. Despite advances in surveillance and research, diagnostic and surveillance challenges persist. This review and secondary analysis highlight the importance of ongoing surveillance, research, and collaboration to mitigate the burden of CHIKV in Africa and improve public health outcomes.

Background. National surveys reported on variable prevalence of chronic kidney disease (CKD) due to differences in characteristics of population, design, equations used to estimate glomerular filtration rate (eGFR) and definitions. The EH-UH 2 survey is the first study evaluating CKD prevalence, characteristics and awareness in Croatia. Methods. This was a cross-sectional nationwide observational study designed to assess the prevalence and cardio-kidney-metabolic risk factors in Croatia which included 1765 randomly selected subjects. We estimated the prevalence of CKD by means of albumin-to-creatinine ratio (ACR) and eGFR (CKD EPI equation). Comorbidities, anthropometric and social factors related to the prevalence of CKD were analyzed, and CV risk profile was evaluated. Results. The weighted prevalence of CKD (any stage), CKD stage ≥ G3A A2, and CKD defined only as eGFR < 60 ml/min/1.73 m2 were estimated at 17.1%, 9.8% and 7.9%, respectively. The prevalence was higher in men than in women (11.8% vs. 7.9%; p 30 mg/g was 15.1%. Older age, male gender, diabetes, ePWV, and uric acid were independently associated with CKD prevalence. The awareness of CKD of 9.5%. Unaware were older with lower income, less educated, having more frequently diabetes, hypertension (less frequently controlled) and milder renal impairment. Conclusion. In Croatia, the estimated prevalence of CKD is high, being more frequently presented in men than in women. CKD patients have unfavorable CV risk profile. The awareness of CKD is very low reflecting poor health literacy in general population but also in health care workers.

Polyalcohol liquefaction can be done by acid or basic catalysis producing polyols with different properties. This study compared the mechanical properties of foams produced using polyols from liquefied Cytisus scoparius obtained by acid and basic catalysis and using two different foam catalysts. The differences were monitored using FTIR analysis. Acid-catalyzed liquefaction yielded 95.1 %, with the resultant polyol having an OH index of 1081 mg KOH/g while basic catalysis yielded 82.5 %, with a similar OH index of 1070 mg KOH/g. Generally, compressive strength with dibutyltin dilaurate (DBTDL) ranged from 16 - 31 kPa (acid-liquefied polyol) and 12 -21 kPa (base-liquefied polyol), while with stannous octoate (TIN), it ranged from 17 - 42 kPa (acid) and 29 - 68 kPa (base). Increasing water content generally decreased the compressive modulus and strength of foams. Higher water content led to a higher absorption at 1670 cm-1 in the FTIR spectrum due to the formation of urea. Higher isocyanate indices generally improved compressive strength, but high amounts led to unreacted isocyanate that could be seen by a higher absorption at 2265 cm-1 and 3290 cm-1. DBTL was shown to be the best foam catalyst due to higher trimer conversion seen in the spectra by a higher absorption at 1410 cm-1. Acid and base-derived polyols lead to different polyurethane foams with different FTIR spectra, particularly with a higher absorption at 1670 cm-1 for foams from acid-derived liquefaction.

In Germany, the phloem sucking planthopper Pentastiridius leporinus (Hemiptera: Cixiidae) currently represents the epidemiological driver for the spread of the syndrome “Basses Richesses” in sugar beet, which results in a reduced sugar content and an economic loss for the farmers. This disease is associated with the γ-proteobacterium ‘Candidatus Arsenophonus phytopathogenicus’ and the Stolbur phytoplasma ‘Candidatus Phytoplasma solani’. Recently, P. leporinus was found in potato fields in Germany associated with Stolbur-like symptoms in this crop. In this study, we confirmed that the vector completes its lifecycle on sugar beet as well as on potato when reared under controlled conditions. Transmission experiments with adults of this vector combined with molecular analyses showed for the first time that both pathogens are transmitted by this vector to potato. For an accurate assessment of the Ca. P. solani and Ca. A. phytopathogenicus titers in the vector and host plants, gBlocks derived from the hsp20- and 16S rRNA gene were employed, respectively. For Ca. P. solani the limit of detection was determined in potato and sugar beet material. The results of this study will further research on the epidemiology of the syndrome “Basses Richesses” and “Stolbur” diseases and the response of host plants and vector insects to both pathogens.

Apple replant disease (ARD) is a complex issue caused by various fungal, oomycetes pathogens and parasites which can differ in their abundance between sites within a geographic region. Knowledge of the specific etiology of ARD at a particular site is required in order to develop commercially viable soil management strategies to combat specific/individual components of the disease. In this study we analyzed the soil from six ARD sites for the presence of fungal, bacterial and oomycetes communities and plant parasitic nematodes. Five fungal, and 17 bacterial classes were differentially represented in the microbiomes from different locations. Mortierellomycetes was the most abundant fungal taxa represented followed by Sordariomycetes. Mortierella exigua a fungal endophyte was the most abundant fungal amplicon sequence variant (ASV) in the core microbiome. Proteobacteria was the most prevalent phylum identified in orchard soils. Several potential phytopathogenic fungi involved in ARD and endophytes including Fusarium oxysporum, F. solani, Nectria ramulariae, Ilyonectria robusta and Nectriaceae were identfied in the orchard soil. Pythium attrantheridium (Globisporangium attrantheridium), P. monospermum and P. ultimum (Globisporangium ultimum) were the most abundant oomycete taxa identified in these soil samples. Six different groups of plant-parasitic nematodes were found across the six orchards soil. Root-lesion nematodes, Pratylenchus spp., which are commonly associated with ARD, were identified in all orchards soil at population densities ranging from 12 to 33/100 cm3 soil. This research contributes valuable understanding of the ARD complex as the apple industry needs alternative approaches to combat the disease.

Crop rotation diversification using legumes has been advocated as one of the solutions to improve the resilience of the crop system to various environmental stresses and the use of nitrogen resources. However, when forage legumes or grass-legumes are ploughed, there is a high risk of nitrate leaching, especially in sandy soils. The aim of the study was to determine the effect strip tillage intercropping management on soil mineral nitrogen (SMN), water-extractable organic carbon (WEOC) content and winter wheat (WW, Triticum aestivum L.) grain yield compared to forage legume and WW monocropping with conventional tillage. In intercropping was used winter wheat - black medick (Medicago lupulina L.) WW+BM, winter wheat - white clover (Trifolium repens L.) WW+WC, and winter wheat - Egyptian clover (Trifolium alexandrinum L.) WW+EC. Research was repeated in two experiments. The results showed that after strip tillage and WW sowing less or similar SMN content cud be detected, as in conventional tillage and WW + forage legumes intercropping. WW grain yield in intercrops decreased, compared to the grasses monocultures that were ploughed before WW sowing. The highest amount of WEOC was in intercropping soil growing WW+WC or in all fields (except WW+EC) after applying strip tillage. During the research period, the amounts of mobile humic substances (HSs) and mobile humic acids (HAs) changed analogously. Their content increased substantially in fields with WC and EC, regardless of whether the grasses were ploughed or grown with WW.

Two experiments were conducted to develop a Nano green manganese and assess its effect on grapevines. The first experiment was microbiological, where several incorporation strategies were utilized to enrich the yeast with manganese, as follows: (1) adding manganese to the liquid medium (growth phase), (2) adding after 24 h of incubation (non-growth phase). As the results, growth phase reduced the possibility of medium contamination. Manganese concentration in the yeast cells was increased as that of manganese sulphate in the medium. Manganese incorporation in yeast cells was 99.93% higher than that of the medium at 0.0195 g/l of manganese. Although the concentration of manganese in the medium raised the OD of yeast cell biomass, manganese sulphate had no passive influence on it. The second experiment was horticultural, done on Flame Seedless grapevines, since both active fresh and frozen yeast enriched with manganese resulted from the first experiment were sprayed twice a year at 10 or 20 cm3/l comparing with manganese sulphate, and manganese chelate. The results demonstrated that yeast extracts in both forms increased the yield and improved fruit properties. The most effective treatment on vegetative growth, yield and fruit properties was the frozen yeast enriched with manganese at 20 cm3/l.

: Background. Delivering bad news is a sensitive and challenging aspect of nursing healthcare, requiring a holistic approach that respects patients' preferences, cultural values, and religious beliefs to promote adaptation to the state's health. Aim: map the evidence of the dimensions present in the communication and management of bad news by nurses, with the person in a palliative situation, their caregivers, and family members. Methods: Based on Joanna Briggs Institute methodology, the search was conducted through MEDLINE Complete (EBSCOhost), CINAHL Complete (EBSCOhost), SciELO, and Open Access Scientific Repository in Portugal. From a total of 756 articles, 14 were included, published between 2018 and 2023. Results: Structure components in bad news are influenced by the characteristics of the palliative patients, their caregivers, family members; nurses; and the organizational environment. Promoting the quality of the communication process is desirable through continuous and advanced training in end-of-life; training in bad news; religiously and culturally sensitive nursing interventions centered on hope and maintaining faith; emotional management; and utilization of a checklist protocol. Conclusions: Honest communication allows people to actively participate in the decision-making process and in the trajectory of the care plan that is focused on themselves and their preferences, which has outcomes in functional capacity and readaptation.

Non-invasive continuous health monitoring has become feasible with the advancement of biosensors. While monitoring certain biomarkers such as heart rate or skin temperature are now at certain maturity, monitoring molecular biomarkers is still challenging. Progress has been shown in sampling, measurement and interpretation of data towards non-invasive molecular sensors that can be integrated in daily wearable items. Towards this goal, this paper explores the potential of embroidered interdigitated transducer (IDT)-based sensors for non-invasive, continuous monitoring of human biomarkers, particularly glucose levels, in human sweat. The study employs innovative embroidery techniques to create flexible fabric-based sensors with gold-coated IDTs. In controlled experiments, we have shown the variation of glucose concentration in water can be wirelessly detected by tracking the resonant frequency of the embroidered sensors. The current sensors operate at 1.8GHz–2GHz and respond to the change of glucose concentration with a sensitivity of 0.17 MHz/(mg/dl). The embroidered IDT-based sensors with wireless sensing will be a new measurement modality for molecular wearable sensors. The establishment of a wireless sensing mechanism for embroidered IDT-based sensors will be followed by investigation of sweat for molecular detection. This will require adding functionalities for sampling and interpretation of acquired data. We envisage the embroidered IDT-based sensors offer a unique approach for seamless integration into clothing, paving the way for personalised, continuous health data capture.

This study aims to investigate the microphysical properties of Arctic, tropospheric aerosol in the transition from the Arctic Haze in spring towards the summer season in 2021. A special focus lies on the hygroscopicity of the aerosol. Therefore, a one-parameter growth curve model is applied to lidar data from the Koldewey Aerosol Raman Lidar (AWIPEV in Ny-Ålesund, Svalbard) and simultaneous radiosonde measurements. Hygroscopic growth depends on different factors like aerosol diameter and chemical composition. To detangle this dependency, three trends in hygroscopicity are additionally investigated by classifying the aerosol first by its color ratio, and then by its season and altitude. Furthermore, two special days are discussed using Mie-theory. They show on the one side the complexity of analyzing hygroscopic growth by means of lidar data, but on the other side demonstrate that it is in fact measurable with this approach. For these two case studies we calculated, that the aerosol effective radius increased from 0.16 μm (dry) to 0.18 μm (wet), and from 0.28 μm to 0.32 μm for the second case. Generally, we found two different modes of stronger or weaker hygroscopic particles and a complex altitude dependence with the least hygroscopic particles in the middle free troposphere.

Continuous technological progress places significant demands on the materials used in increasingly modern devices. An important parameter is often the long-term thermal resistance of the material. The use of heat-resistant polymer materials worked well in technologically advanced products. An economically justified direction in searching for new materials is the area of polymer nanocomposite materials. It is necessary to appropriately select both the polymer matrix and the nanofillers best able to demonstrate the synergistic effect. A promising area of exploration for such nanocomposites is the use of organosilicon polymers, which results from the unique properties of these polymers related to their structure. This review presents the results of the analysis of the most important literature reports regarding organosilicon polymer nanocomposites with increased thermal resistance. Particular attention was paid to modification methods of silicone nanocomposites focused on the increase of their thermal resistance related to the modification of siloxane molecular structure and by making nanocomposites using inorganic additives, carbon nanomaterials. Attention was also paid to such important issues as the influence of the dispersion of additives in the polymer matrix on the thermal resistance of silicone nanocomposites and the possibility of modifying the polymer matrix and permanently introducing nanofillers thanks to the presence of various reactive groups. The thermal stability mechanism of these nanocomposites was also analysed.

The development of accurate dynamic battery pack models for electric vehicles (EVs) is critical for the ongoing electrification of the global automotive vehicle fleet, since these serve as a key element in the energy performance of an EV powertrain system. The Equivalent Circuit Model (ECM) technique at the cell level is commonly employed for this purpose, combining accuracy and efficiency in the representation of battery operation within the broader powertrain system. In this study, a second-order ECM model of a battery cell is being developed using Modelica, an equation-based modeling language. Parameter lookup tables at multiple levels of state of charge (SoC), extracted from Li-ion battery cells with 4 different commonly used cathode materials, have been utilized. This approach allows for a representation of the battery systems that are used in a wide range of commercial EV applications. To verify the model, an integrated EV model is developed and simulation results of the FTP75 driving cycle have been compared against an equivalent application in MATLAB Simulink. The findings demonstrate a close match between the results obtained from both software across different system points. Specifically, the maximum deviation of SoC is limited to 0.08% and the maximum value of relative voltage deviation is 1.4%. The verified model enables the exploration of multiple possible architecture configurations of EV powertrains with Modelica.

Nowadays, animal breeders look for effective innovations to care animal health. Use of probiotics, postbiotics, parabiotics and the other beneficial natural substances are dominated. Mundticin-like substance EM 41/3 is thermo-stable bacteriocin (postbiotic) with a broad antimicrobial spectrum. In this study its effect in broiler rabbits was assessed. Rabbits represent food-derived animal and they are also suitable animal model. The parameters tested were analyzed by validated methods. Administration of MLS EM 41/3 produced by non-autochthonous strain Enterococcus mundtii EM 41/3 lead to significant increase of parameter immunity-phagocytic activity, while it did not influence microbiota composition. It also did not influence blood biochemistry and no oxidative stress was noted. Moreover, higher growth parameters were noted and also stimulated hydrolytic activity. Finally, no negative influence on rabbit meat quality was noted. Postbiotic MLS EM 41/3 administration in feeding strategy seems to be contributing fact for rabbit health status maintaining.

Today, it is difficult to have a high-field nuclear magnetic resonance device (NMR) due to the high cost of its acquisition and maintenance. These high-end machines require significant space and specialist personnel for operation and offer exceptional quality in the acquisition, processing, and other advanced functions associated with detected signals. However, alternative devices are low-field nuclear magnetic resonance devices. They benefit from the elimination of high-tech components that generate static magnetic fields and advanced instruments. Instead, they used magnetic fields induced by ordinary conductors. Another category of spectrometers uses the Earth's magnetic field, which is simple and economical, but limited in use. These devices are called Earth Field Nuclear Magnetic Resonance (EFNMR). This device is ideal for educational purposes, especially for engineers and those who study nuclear magnetic resonance, such as chemistry or other experimental sciences. Students can observe their internal workings and conduct experiments that complement their education without worrying about damaging equipment. This article provides a detailed explanation of the design and construction of electrical technology devices for the excitation of atomic spin resonance using Earth's magnetic fields. Covers all necessary stages, from research to analysis, from simulation, assembly, construction of each component, and the development of comprehensive software for spectrometer control.

Ice formation on aircraft surfaces poses significant safety risks, and current detection systems often struggle to provide accurate, real-time predictions. This paper presents the development and comprehensive evaluation of a smart ice control system using a suite of machine learning models. The system utilizes various sensors to detect temperature anomalies and signal potential ice formation. We trained and tested supervised learning models (Logistic Regression, Support Vector Machine, Random Forest), unsupervised learning models (K-means clustering), and neural networks (Multi-Layer Perceptron) to predict and identify ice formation patterns. Experimental results demonstrate that our smart system, driven by machine learning, accurately predicts ice formation in real-time, optimizes de-icing processes, and enhances safety while reducing power consumption. This solution holds the potential for improving ice detection accuracy in aviation and other critical industries requiring robust predictive maintenance.

This paper investigates pseudo-polymorphism in 2-pyridylmethoxy derivatives of p-tert-butylcalix[4]arene (PyC4), p-tert-butyldihomooxa-calix[4]arenes (PyHOC4), and p-tert-butylhexahomotrioxacalix[3]arenes (PyHO3C3), presenting 11 crystal structures with 15 crystallographically independent molecules. The macrocycle of PyC4 is smaller and less flexible with respect to those of PyHOC4 and PyHO3C3 and in solution, the cone conformation of these three molecules exhibit different point symmetries: C4, Cs and C3, respectively. A correlation is observed between the macrocycle's structural rigidity and the number of pseudo-polymorphs formed. The more rigid PyC4 displays a higher number (6) of pseudo-polymorphs compared to PyHOC4 and PyHO3C3, which exhibit a smaller number of crystalline forms (3 and 2, respectively). The X-ray structures obtained show that the conformation of the macrorings is primarily influenced by the presence of an acetonitrile guest molecule within the cavity, with limited impact from crystal packing and intermolecular cocrystallized solvent molecules. Notably, both calix[4]arene derivatives produce host-guest complex with acetonitrile, while the most flexible and less aromatic PyHO3C3 do not give crystals with acetonitrile as guest. Intertwined 1D and 2D solvent channel networks were observed in the PyHOC4-hexane and in the PyHO3C3-H2O-MeOH crystal structures, respectively, while the other pseudopolymorphs of PyHOC4 and PyHO3C3 and all PyC4 crystal forms exhibit a closely packed crystal structures without open channels.

Vernonia mespilifolia is widely used in folk medicine in the Eastern Cape Province, South Africa. The aim of this study was to evaluate the biological activity of the acetone, aqueous and ethanol extracts of Vernonia mespilifolia using brine shrimp hatchability and lethality assay. The result showed hatching success in this order: aqueous extract (48.6%) > acetone extract (38.2%) > ethanol extract (26.8%). The LC₅₀ of the lethality assay were in this order: acetone extract (67.8 µg/mL) > aqueous extract (132 µg/mL) > ethanol extract (383 µg/mL). According to Meyer’s toxicity index (using brine shrimps), LC₅₀ < 1000 µg/ mL is toxic. Therefore, the results of the three solvent extracts could be said to be toxic as do have LC₅₀ < 1000 µg/ mL. However, the toxicity of the crude extracts could suggest or confer some antitumor properties, hence further in vitro, in vivo and antitumour assays are recommended to further substantiate these claims.

Laser Photoacoustic Spectrometers (LPAS), which provide photoacoustic spectra for detecting food frauds or adulteration, and fluorescence-based systems for recognition of contamination by heavy metal ions in water are two important families of sensors for health and environmental purposes. Both sensor families require one or more low-frequency Lock-In Amplifiers (LIAs) to extract the signal of interest from background noise. In the cited applications, the required LIA frequency is quite low (up to 1kHz), and this leads to a simplification of the hardware with consequent good results in portability, economy, reduced size, weight and low-cost characteristics. The present system, called ENEA DSP Box Due, is based on a very inexpensive microcontroller proto-board and can replace four commercial LIAs, resulting in significant savings in both cost and space. Furthermore, it incorporates a dual-channel oscilloscope and a sinusoidal function generator. This article outlines the architecture of the ENEA DSP Box Due, its electrical characterization and its applications within a project concerning laser techniques for food and water safety.

This study presents PlanteSaine, a novel mobile application powered by Artificial Intelligence (AI) models explicitly designed for maize, tomato, and onion farmers in Burkina Faso. Agriculture in Burkina Faso, like many developing nations, faces substantial challenges from plant pests and diseases, posing threats to both food security and economic stability. PlanteSaine addresses these challenges by offering a comprehensive solution that provides farmers with real-time identification of pests and diseases. Farmers capture images of affected plants with their smartphones, and PlanteSaine's AI system analyzes these images to provide accurate diagnoses. The application's offline functionality ensures accessibility even in remote areas with limited internet connectivity, while its messaging feature facilitates communication with agricultural authorities for guidance and support. Additionally, PlanteSaine includes an emergency alert mechanism to notify farmers about pest and disease outbreaks, enhancing their preparedness to deal with these threats. An AI-driven framework, featuring an image feature extraction phase with EfficientNetB3 and an artificial neural network (ANN) classifier, was developed and integrated into PlanteSaine. The evaluation of PlanteSaine demonstrates its superior performance compared to baseline models, showcasing its effectiveness in accurately detecting diseases and pests across maize, tomato, and onion crops. Overall, this study highlights the potential of PlanteSaine to revolutionize agricultural technology in Burkina Faso and beyond. Leveraging AI and mobile computing, PlanteSaine provides farmers with accessible and reliable pest and disease management tools, ultimately contributing to sustainable farming practices and enhancing food security. The success of PlanteSaine underscores the importance of interdisciplinary approaches in addressing pressing challenges in global agriculture

Infection with the malaria parasite Plasmodium, remains a major cause of illness and death world-wide. The development of evasion strategies by the parasite from host immunity and its adaptability to antimalarial drugs has raised the urgency for developing new strategies to combat this disease. One promising avenue is targeting telomeres – sequences found at chromosome termini– and telomerase – the enzyme that catalysis synthesis of telomeres using an intrinsic RNA template. As telomeres shorten critically, cells undergo replicative senescence or apoptosis. Plasmodium, lacking telomerase activity in its human stages, exploits alternative mechanisms, accelerating telomere shortening, aging, and immune evasion. Chemical telomerase inhibitors show promise as antimalarials. In this review, we examine the potential of targeting this system in malaria therapy, with telomerase inhibitors offering a novel approach. A systematic search on PubMed using Boolean techniques identified 246 relevant articles from 1985 to March 31, 2024. After filtering, 43 articles met inclusion criteria, supplemented by snowball sampling. The telomerase inhibitor drug strategy is widely applicable against cancer. However, given the drugability of telomerase and the absolute requirement for active telomere maintenance in the vast majority of parasites including plasmodium, telomerase and telomere maintenance could well represent the Achilles heel of the parasite

Although the influence of climate on the fire regime is unanimously recognized, most publications are studies on this influence are at the global scale. Therefore, this study aims to demonstrate the role of climate in the incidence of wildfires at the country and regional scale using statistical analysis and machine learning methods. Mainland Portugal was chosen as a case study due to its climate and because it is the European region most affected by wildfires. Results demonstrate the climate signature in the spatial and temporal distribution of the wildfire incidence. The conclusions of the study include (i) the existence of two pyro-regions, with different types of climate (Csb and Csa) composed of NUTS II regions: the northern region composed of the Norte and Centro regions and the southern region composed of Alentejo and Algarve; (ii) the intra-annual variability in the incidence of wildfires, characterized by two peaks, one in spring and the other in summer, are a consequence of the country's type of climate; and, (iii) how the annual cycle of wildfire incidence varies over the years depends on the weather conditions throughout each year. These results are of fundamental importance for wildfire managers, especially in the context of climate change.

Being able to express broad families of equivariant or invariant attributed graph functions is a popular measuring stick of whether graph neural networks should be employed in practical applications. However, it is equally important to learn deep local minima of losses (i.e., with much smaller loss values than other minima), even when architectures cannot express global minima. In this work we introduce the architectural property of attracting GNN optimization trajectories to local minima as a means of achieving smaller losses. We take first steps in satisfying this property for losses defined over attributed undirected unweighted graphs with a novel architecture, called Universal Local Attractor (ULA). The latter refines each dimension of end-to-end trained node feature embeddings based on graph structure to track the optimization trajectories of losses satisfying some mild conditions. The refined dimensions are then linearly pooled to create predictions. We experiment on 10 tasks, from node classification to clique detection, on which ULA is comparable with or significantly outperforms popular alternatives of similar or greater theoretical expressive power.

Little is known about public knowledge of meat chicken production and how it influences attitudes to birds’ welfare and consumer behaviour. We interviewed 506 members of the public in SE Queensland, Australia, to investigate this. Knowledge was assessed from 15 questions, and low scores were supported by respondents’ self-assessed report of low knowledge levels and agreement that their knowledge was insufficient to form an opinion about which chicken products to purchase. Older respondents and single people without children were most knowledgeable. There was uncertainty about whether chicken welfare was adequate, particularly in those with little knowledge. There was also evidence that lack of empathy towards chickens related to lack of knowledge, since those that thought it very acceptable that some birds are inadequately stunned at slaughter had low knowledge scores. More knowledgeable respondents ate chicken more frequently and were less likely to buy products with accredited labelling. Approximately half of the respondents thought the welfare of the chicken to be more important than the cost. It is concluded that the public’s knowledge has an important connection to their attitudes and consumption of meat chickens. Respondents with little knowledge demonstrated that they had both lack of empathy and intolerance to religious slaughter practices.

Deep Eutectic Solvents (DESs) show promising abilities for the delamination of multilayer packaging films that are used in food packaging and in pharmaceutical blister packs. Due to the complexity of their structure, the recycling of these materials is a challenging task, leading to the easiest or cheapest option, landfilling. Towards the development of ‘green’ solvents for the efficient waste management and recycling, the conducted research focuses on the preparation of a range of hydrophobic and hydrophilic DES based on carboxylic acids. Also, their chemical and physical characterization, such as DSC, rheometer and density measurements, was followed for the determination of their properties. The laminate packaging waste products that were tested were Al/PE, PE/Al/PET, Al/PE/paper and PVC/PE/Al. Different batches of solvent systems were tested based on various naturally derived aliphatic and aromatic organic compounds as well as amino acids. The separated films were collected and studied further for the examination of the delamination extend. Results showed full or partial delamination of some materials as well as challenges of solvent systems. Variables such as temperature, agitation rate, mixing time and solvents ratios were monitored and collected during the design of experimental process. The results showed that the used DESs can offer an efficient, low-energy, affordable and green option for the delamination tested packaging materials.

In order to comprehensively evaluate the employee satisfaction of mine occupational health and safety management system, an analytic method based on fuzzy analytic hierarchy process and 2- tuple linguistic model was established. Firstly, based on the establishment of 5 first- grade indicators and 20 second- grade ones, the weight of each indicator is calculated and validated by method of FAHP and root mean square model. Secondly, a path based on the time-ordered Weighted Averaging Operator (T-OWA) model is constructed. Finally, the model is validated by empirical analysis. The results demonstrate that the employee satisfaction of the mine occupational health and safety management system is of the “general” rank. The method including the comprehensive evaluation of employee satisfaction and the quantitative analysis of language evaluation information ensures the authenticity of the language evaluation information.

Surface acoustic wave (SAW) is effective for the manipulation of fluids and particles in microscale. The current approach of integrating interdigitated transducers (IDTs) for SAW generation into microfluidic channels involves complex and laborious microfabrication steps. These steps often require the full access to clean room facilities and hours to align the transducers to the precise location. This work presents an affordable and innovative method for fabricating SAW-based microfluidic devices without the need of clean room facilities and alignment. The IDTs and microfluidic channels are fabricated in the same process and thus precisely self-aligned in accordance with the device design. With the use of the developed fabrication approach, a few types of different SAW-based microfluidic devices have been fabricated and demonstrated for particle separation and active droplet generation.

In this study, we present comprehensive climatologies of effective ultraviolet (UV) quantities and photosynthetically active radiation (PAR) over Cyprus for the period 2004 to 2023, leveraging the synergy of earth observation (EO) data and radiative transfer model simulations. The EO dataset, encompassing satellite and re-analysis data for aerosols, total ozone column, and water vapor, alongside cloud modification factors, to capture the nuanced dynamics of Cyprus's atmospheric conditions. With a temporal resolution of 15 minutes and a spatial of 0.05°x0.05°, these climatologies undergo rigorous validation against established satellite datasets and are further evaluated through comparisons with ground-based global horizontal irradiance measurements provided by the Meteorological Office of Cyprus. This dual-method validation approach not only underscores the models' accuracy but also highlights their proficiency in capturing intra-daily cloud coverage variations. Our analysis extends to investigating the long-term trends of these solar radiation quantities, examining their interplay with changes in cloud attenuation, aerosol optical depth (AOD), and total ozone column (TOC). Significant decreasing trends in the noon ultraviolet index (UVI), of -2 to -4% per decade have been found in Autumn, especially marked on the island’s Northeastern part, mainly originating from the (significant) positive trends in TOC. The significant decreasing trends in TOC, of -2 to -3% per decade that were found in Spring do not result in correspondingly significant positive trends in the noon UVI since variations in cloudiness and aerosols also have a strong impact on the UVI in this season. The seasonal trends in the Daylight Integral (DLI) were generally not significant. These insights provide a valuable foundation for further studies aimed at developing public health strategies and enhancing agricultural productivity, highlighting the critical importance of accurate and high-resolution climatological data.

Fire detection from satellite sensors relies on an accurate estimation of the unperturbed state of a target pixel, from which an anomaly can be isolated. Methods for estimating the radiation budget of a pixel without fire depend upon training data derived from the location's recent history of brightness temperature variation over the diurnal cycle, which can be vulnerable to cloud contamination and the effects of weather. This study proposes a new method that utilises the common solar budget found at a given latitude in conjunction with an area's local solar time to aggregate a broad-area training dataset, which can be used to model the expected diurnal temperature cycle of a location. This training data is then used in a temperature fitting process with the measured brightness temperatures in a pixel, and compared to pixel-derived training data and contextual methods of background temperature determination. Results of this study show similar accuracy between clear-sky medium wave infrared upwelling radiation and the diurnal temperature cycle estimation compared to previous methods, with demonstrable improvements in processing time and training data availability. This method can be used in conjunction with brightness temperature thresholds to provide a baseline for upwelling radiation, from which positive thermal anomalies such as fire can be isolated.

Simple Summary: 200 words Will biology, including humans, benefit or harm from new developments in information such as artificial intelligence (AI). First, are biology and information different? Life is an ordered form that can reproduce, maybe with variation; and any ordered arrangement, biological or not, potentially contains information. There have been ordered forms since earth was just a ball of chemicals, and some such chemicals can reproduce. So biological and non-biological information might be components of a unified process, ‘PanEvolution’ or ‘Pan-Evo’, based on the same four operations for living or non-living entities - Innovation; Transmission and replication; Adaptation; and Movement. This can produce separate groups called ‘species’. In a current Panspeciation event, information held in biology - especially our brains - is moving into its own environment. Harm to biology might be minimal if humans and AI both behave intelligently, because vastly different environments are optimal for humans and machines containing AI. This would be the first speciation-like event involving humans for millennia, but will not be particularly hostile to humans, if humans learn how to evaluate information and cooperate, to minimize the effect of both human stupidity and artificial simulated stupidity (ASS – a failure of AI). Abstract: 200 words Many people wonder whether biology, including humans, will benefit or harm from new developments in information such as artificial intelligence (AI). Biological and non-biological information might be components of a unified process, ‘Pan-Evolution’ or ‘Pan-Evo’, based on four basic operations – Innovation, Transmission, Adaptation, and Movement. Pan-Evo contains many types of variable objects, from molecules to ecosystems. Biological innovation includes mutations and behavioural changes; non-biological innovation includes naturally-occuring physical innovations, and innovation in software. Replication is commonplace in and outside biology, including autocatalytic chemicals, and autonomous software replication. Adaptation includes biological selection, autocatalytic chemicals and ‘evolutionary programming’ used in AI. Extension of biological speciation to non-biological information, creates a concept called ‘Panspeciation’. Panevolution might benefit or harm biology, but harm might be minimal if AI and the humans behave intelligently, because humans, and the machines in which AI resides, might split to the vastly different environments that suit them. That is a possible example of panspeciation, and would be the first speciation event involving humans for thousands of years. This event will not be particularly hostile to humans, if humans learn to evaluate information and cooperate better, to minimize both human stupidity and artificial simulated stupidity (ASS – a failure of AI).

The aim of this work is research dedicated to the search for new bactericidal systems for use in cosmetic formulations, dermocosmetics, or the production of wound dressings. Over the last two decades chitosan due to its special biological activity, has become a highly indispensable biopolymer with very wide application possibilities. Literature reports on the antibacterial effects of chitosan are very diverse, but our research has shown that they can be successfully improved through chemical modification. Therefore, in this study, results on the synthesis of new Schiff bases chitosan – dCsSB-SFD and dCsSB-PCA obtained using two aldehydes: sodium 4-formylbenzene-1,3-disulfonate (SFD) and 2-pyridine carboxaldehyde (PCA) respectively. Chitosan derivatives synthesized in this way demonstrate stronger antimicrobial activity. Carrying out the procedure of grafting chitosan with a caproyl chain allowed obtaining compatible blends of chitosan derivatives with κ-carrageenan, which are stable hydrogels with a high swelling coefficient. Furthermore, covalently bounded PCL improved the solubility of obtained polymers in organic solvents. With this respect, the Schiff base-containing polymers obtained in this study, with special hydrogel and antimicrobial properties are very promising materials for the potential use as a controlled-release formulation of both, hydrophilic and hydrophobic drugs in cosmetic products for skin health.

Recently, the concept of participatory democracy developed in the early 1970s has come back into fashion to revitalize the public involvement in political decision-making processes. Public par-ticipation in forest policy has been fully conceptualized by the scientific community in the late 1990s and early 2000s, but in many contexts the practical application remains unfulfilled. The aim of this study is to identify and analyze the participatory techniques used in literature to increase knowledge and facilitate its transferability into forest policies and strategies. A literature review was carried out to offer an overview of the participatory techniques adopted in the deci-sion-making process. At the end of literature review, 25 participatory techniques were identified based on over 2,000 publications. Afterwards, the participatory techniques were assessed using seven indicators (degree of participation, type and number of participants, time scale, cost, po-tential influence on policy). The results showed that the type of actors involved in the participa-tory technique is a key variable for the complexity and usefulness of the process, while the number of participants influences how information is disseminated. The Principal Component Analysis highlighted that the participatory techniques can be divided in three groups: the first group includes those techniques with a high degree of participation and a contextual high po-tential influence on policies, the second one includes techniques with a costs in terms of re-sources, while the third one consists of those with a large number of participants and reduced time requirements.

The protection and regulation of international trade of Australia’s native species is legislated by its Environment Protection and Biodiversity Conservation Act of 1999. In response to overwhelming evidence that the Act is ineffective at protecting biodiversity, the Australian Government is currently reforming its environmental laws. One problematic component of the Act is in cases where threatened species interact with multiple regulatory and management frameworks, such as commercially fished marine species that are traded as seafood. Here, we analyzed international seafood trade data and found that Australia exports four threatened fish species listed under the Act and additional species acknowledged as globally threatened. In light of our analysis, we have three recommendations for Australia’s new environmental legislation: 1) apply the same precautions to commercially harvested species as to other threatened species; 2) review the status of all threatened species annually; and 3) assess species listed on global conservation conventions. These recommendations will help ensure that Australia’s marine biodiversity is protected, despite its commercial value.

This paper studies the maximum reliability of multi-hop relay UAV, in which UAV provides wireless services for remote users without direct communication link on the ground as a coded cooperative relay. In this paper, the analytical expressions of total power loss and total bit error rate are derived as reliability measures. Firstly, based on the environmental statistical parameters, a LOS probability model is proposed. Then the problem of minimizing the bit error rate of static and mobile UAVs is studied. The goal is to minimize the total bit error rate by jointly optimizing the height, elevation, power and path loss, and subject to the maximum allowable path loss con-straints, transmission power allocation constraints and UAV height and elevation constraints. At the same time the total path loss is minimized to achieve maximum ground communication cov-erage. However, the formulated joint optimization problem is non-convex and generally difficult to solve. Therefore, we decomposed the problem into two subproblems and proposed an effective joint optimization iteration algorithm. Finally, the simulation results are given, and the analysis shows that the optimal height of different reliability measures is slightly different, and using the mobility of UAVs can improve the reliability of communication performance.

The temperature variations caused by the climate changes taking place in the Basilicata region, southern Italy - Ionian Seaside of the Gulf of Taranto - on the territory of the DOP Matera vineyard, were studied by means of an analysis of temperature trends considering both the period of the vegetative-productive season of the vineyards and the whole year. Two datasets were analyzed for this study: data from ERA5-Land of the C3S Climate Data Store -relative to the 1981-2022 window- and data from 5 weather stations belonging to the agrometeorological network of the Lucanian Agency for Development and Innovation in Agriculture (SAL-ALSIA), relative to the 2000-2023 window. From the results of this study, it can be deduced that, for the historical period analyzed, the Matera DOP area showed a clear and worrying trend of increasing temperatures and, in par-ticular, minimum temperatures. This increase, moreover, is more evident at higher elevations than at lower elevations close to the sea. At lower altitudes, in fact, temperatures are strongly “buffered” by the thermoregulatory activity of the bordering Ionian Sea. It follows that the DOP Matera viticultural areas, and in particular the areas furthest from the coastal strip, will already have to adapt to severe climatic conditions that will undoubtedly affect the quality and typicality of the wines.

Human serum albumin (HSA) corona formation at polymer microparticles of a spheroidal shape was studied using dynamic light scattering and laser Doppler velocimetry (LDV). Physicochemical characteristics of the albumin comprising, the zeta potential and the isoelectric point were determined as a function of pH for various ionic strengths. Analogous characteristics of the polymer particles were carried out. The adsorption of albumin on the particles was monitored by electrophoretic mobility measurements (LDV). The stability of the HSA functionalized particle suspensions under various pHs and their electrokinetic properties were determined. The deposition kinetics of the particles on mica, silica and gold sensors were determined in situ by optical microscopy, AFM and by the quartz microbalance (QCM) under diffusion and flow conditions. The obtained results were interpreted in terms of the coarse-grained random sequential adsorption model that allowed to estimate the range of applicability of QCM for determining deposition kinetics of virus and bacteria at abiotic surfaces.

Metabolic syndrome (MetS) refers to the group of several interconnected risk factors that collectively double the risk of cardiovascular disease. Epilepsy is linked to MetS across all age groups, though its prevalence differs across various studies. This can be understood from the perspective of seizure-related metabolic abnormalities, long-term antiepileptic drugs (AEDs) use, and a more sedentary lifestyle due to epilepsy. The factors that are considered in developing MetS for patients with epilepsy (PWE) are age, residence, level of physical activity, food intake status, epilepsy subtype, epilepsy duration, current (AEDs) use, drug responsiveness status, body-mass index (BMI), total cholesterol and LDL-cholesterol levels. A deeper understanding of the epilepsy-AED-MetS connection and the exploration of lifestyle interventions hold the promise of significantly improving the overall health and well-being of PWE. Clinicians managing PWE should closely monitor various risk factors for developing MetS and consider them when selecting AED treatment.

Increasing efforts have been devoted to promoting sustainable demolition waste management (DWM) from a life cycle-thinking perspective. To this end, facilitating sustainability-oriented de-cision-making for DWM planning requires a sustainability assessment framework for assessing multifaceted criteria. This study develops a BIM-based DWM sustainability assessment ap-proach to facilitate the life cycle assessment (LCA) and decision-making by coupling the enriched IFC model with hybrid Multi-Criteria Decision-Aiding (MCDA) methods using Dynamo visual scripting. To streamline the data-intensive LCA process, this study enriched the BIM properties and accommodated them into the LCA data template to enhance data interoperability, thus achieving seamless data transfer. Moreover, hybrid MCDA methods are integrated into the deci-sion-making workflow for DWM scenario ranking. A pilot study is employed to verify the ap-plicability of the decision-aiding framework. The results unveil that the sustainability score ascended with the recycling rate. The optimal DWM alternative with the highest recycling rate yields the highest sustainability score at 91.63. Conversely, a DWM alternative reflecting the ‘status quo’ in China’s recycling industry has the lowest score at 8.37, significantly lower than the baseline scenario with a 50% recycling rate. It is worth noting that the ‘growth curve’ of the sustainability score continuously flattens as the target recycling rate escalates. The increment in recycling rate from the “Australian standard” scenario to the optimal scenario is 18.4%, while the sustainability score merely increases by 2.3%, signal-ling that the former scenario arrived at an optimum point for maximising the cost-efficiency of DWM under the predefined framework and contexts.

Proteins have the ability to adsorb on the surface of materials, such as soft contact lenses (SCLs), and can affect the hydrophobicity, roughness and surface properties of the contact lenses (CLs), which, in turn, can influence the friction between the lenses and the ocular surface. Excessive friction between contact lenses and the ocular surface can lead to discomfort for the wearer and may cause irritation or inflammation of the cornea, better known as corneal ulcers (keratitis). Bovine serum albumin (BSA) is often used as a standard protein in biocompatibility testing of materials, including contact lenses. One standard commercial contact lenses was tested under lubricated conditions to access the coefficient of friction (CoF), being the contact lubricated with a tear like fluid (TLF) solution containing six different concentrations of BSA. In all cases, a good linearity of the results of the friction force was verified, so the first friction law can be applied to determine the value of the coefficient of friction. It was found that friction increases with increasing protein concentration.

Computational models of homologous protein groups are essential in sequence bioinformatics. Due to the diversity and rapid evolution of viruses, the grouping of protein sequences from virus genomes is particularly challenging. The low sequence similarities of homologous genes in viruses require specific approaches for sequence- and structure-based clustering. Furthermore, the annotation of virus genomes in public databases is not as consistent and up-to-date as for many cellular genomes. To tackle these problems, we have developed VOGDB, a database of Virus Orthologous Groups. VOGDB is a multi-layer database that progressively groups viral genes into groups connected by increasingly remote homology. The first layer is based on pair-wise sequence similarities, the second layer is based on the sequence profile alignments and the third layer uses predicted protein structures to find the most remote homology. VOGDB groups allow for more sensitive homology searches of novel genes and increase the chance of predicting annotations or inferring phylogeny. VOGDB uses all virus genomes from RefSeq and partially re-annotates them. VOGDB is updated with every RefSeq release. The unique feature of VOGDB is inclusion of both prokaryotic and eukaryotic viruses in the same clustering process which makes it possible to explore old evolutionary relationships of the two groups. VOGDB is freely available at https://vogdb.org under the CC BY 4.0 license.

Background: The advantage of a robotic assisted (RARP) over a laparoscopic (LRP) approach in radical prostatectomy (RP) remains to be demonstrated. Aim of the study is to use a homogeneous population in real life and single surgeon surgery, to analyze the oncological and functional results based on the type of the surgical approach. Methods: This is a prospective trial on non-metastatic prostate cancers (PC) patients considered after multidisciplinary decision to RP, using RARP or LRP. A real-life setting was analyzed at our Urological Departments, using homogeneous criteria for the management of PC cases and a one surgeon experience on 444 cases (284 LRP and 160 RARP) .Results: Mean operative time was significantly lower in RARP (173.33±44.3 min) than in LRP (153.21±25.1 min) (p<0.001). In cases submitted to an extended lymph node dissection (eLND), the mean number of lymph nodes removed was 15.16±7.83 and 19.83±4.78 respectively in LRP and RARP procedures (p<0.001), but positive lymph nodes (pN1) were similarly found in 15.8% of LRP patients and 13.6% of RARP patients (p=0.430). Surgical margins (SM) positivity was not significantly higher in RARP group (20.0%) when compared to LRP group (15.9%) (p=0.145). During the postoperative follow-up, a biochemical recurrence (BCR) was detected in 14.4% and 7.5% of cases in the LRP and RARP group respectively (p=0.014). Better results of PAD test at 3-month interval using RARP approach (mean pad weight 75.57±122 grams and 14±42 grams respectively in LRP and RARP (p<0.01)) were described. Conclusions: In the comparison between RARP and LRP approach, a clear advantage of the robotic approach is a significant reduction in operating times, days of hospitalization and postoperative catheterization compared to laparoscopic surgery. It is not possible to describe any certain oncological advantage both in terms of surgical margins and pathological lymph nodes removed. In RARP cases a reduction to the limit of significance is described in terms of biochemical recurrence. RARP produces a more rapid recovery of urinary continence at 3 months postoperatively without significant advantages in terms of erective potency recovery.

Microparticles derived from biomaterials are becoming increasingly popular for various applications, particularly in drug delivery systems. In this study, the water-in-oil (W/O) emulsification-diffusion method was used to create cellulose (C), silk fibroin (SF), and C/SF composite microparticles. We then observed the morphology of all obtained microparticles using scanning electron microscopy (SEM), evaluated their functional groups using attenuated total reflection Fourier transform infrared spectroscopy (ATR-FTIR), and conducted thermogravimetric analysis using a thermogravimetric analyzer (TGA). SEM micrographs indicated that the native SF microparticles have the highest spherical shape with smooth surfaces. With blue dextran, the C microparticle was smaller compared to the native microparticle, while the drug-loaded SF microparticles were bigger than the native microparticle. The morphological surfaces of the C/SF composite microparticles were varied in shape and surface depending on the C/SF ratio used. The spherical shape of the C/SF composite microparticle was increased as SF content increased. Furthermore, the size of drug-loaded C/SF composite microparticles was gradually increased by the SF content. The significant functional groups in the C and SF structures were identified based on the ATR-FTIR data, and a suggestion was made regarding the interaction between the functional groups of each polymer. When compared to both native polymers, the C/SF composite microparticles exhibit improved thermal stability. The C/SF composite microparticle at a 1:3 ratio had the lowest drug release content, whereas the hydrophilicity of the C microparticle affected the highest drug release content. As a result, one crucial factor affecting the medication released from the microparticle is its thermal stability. According to the obtained results, C, SF, and C/SF composite microparticles show promise as delivery systems for drugs with controlled release.

Heat pumps are increasingly becoming a key solution in the quest for decarbonization, offering a significant advantage over traditional boilers due to their superior energy efficiency. Not only can heat pumps provide both heating and cooling, but they also achieve thermal efficiencies exceeding 500%, which can seem to defy conventional expectations. The outdoor unit of a heat pump consists of about twenty main components, one of which is a complex network of copper pipes and sheets welded to valves, connectors, and other fittings. This set involves over thirty welded joints, highlighting a significant opportunity for reducing manufacturing time through process optimization. Copper is a critical material extensively used in various applications due to its excellent thermal and electrical conductivity. However, these very properties make welding copper particularly challenging, especially when aiming to automate and streamline industrial processes. Traditionally, connecting copper pipes and fittings is done through brazing, yet, alternative methods such as LASER welding, electron beam welding, resistance welding, friction welding, and ultrasonic welding also exist. This study focuses on the ultrasonic welding of copper, aiming to identify the optimal parameters that maximize the mechanical strength of overlapping joints and ensure effective tube sealing. Experimental results showed that for copper sheets, the best outcomes were achieved with a welding time of 3 s and a pressure of 6 bar. For tube sealing, the optimal conditions were a welding time of 3 s and a pressure of 4 bar. For both scenarios, the same variables were used, retention time of 0.62 s, initial pressure of 2 bar, retention pressure of 2 bar and sonotrode rising pressure of 3 bar. The analysis reveals that ultrasonic welding of copper can achieve both robust mechanical strength and reliable sealing, making it a promising technique for industrial applications.

National heatwave plans are aimed at reducing the avoidable human health consequences due to heatwaves, by providing warnings to and improving communication between relevant stakeholders. The aim of this study was to assess the perceptions of key stakeholders within plans in Belgium and the Netherlands on their responsibilities, the partnerships, and the effectiveness of the local implementation in Brussels and Amsterdam. Key informant interviews were held with stakeholders that had an important role in development of the heatwave plan in these countries, or its implementation in Brussels or Amsterdam. Care organisations, including hospitals and elderly care organisations, had a lack of familiarity with the national heatwave plan in both cities, and prioritised heat the lowest. Some groups of individuals, specifically socially isolated individuals, are not sufficiently addressed by the current national heatwave plans and most local plans. Stakeholders reported that responsibilities were not clearly described and that the national plan does not describe tasks on a local level. We recommend to urgently increase awareness on the impact of heat on health among care organisations. More emphasis needs to be given to the variety of heat risk groups. Stakeholders should be involved in the development of updates of the plans.