Photocatalytic ammonia decomposition to produce N2 and H2 was achieved using single-walled carbon nanotube (SWCNT) nanohybrids. Physical modification of ferrocene-dye-encapsulated CNTs by amphiphilic C60-dendron yielded nanohybrids with a dye/CNT/C60 coaxial heterojunction. Upon visible light irradiation, an aqueous solution of NH3 and dye@CNT/C60-dendron nanohybrids produced both N2 and H2 in a stoichiometric ratio of 1:3. Action spectra of this reaction clearly demonstrated that the encapsulated dye acted as the photosensitizer, with an apparent quantum yield (AQY) of 0.22% at 510 nm (the λmax of the dye). This study presents the first example of dye-sensitized ammonia decomposition and offers a new avenue for developing efficient and sustainable photocatalytic hydrogen production systems.

Human exposure to carbon nanotubes (CNTs) can cause health issues due to their chemical–physical features and biological interactions. These nanostructures cause oxidative stress, also due to endogenous ROS production, which increases following mitochondrial impairment. The aim of this in vitro study was to assess the health effects, due to mitochondrial dysfunction, caused by a sub-chronic exposure to a non-acutely toxic dose of multi walled CNTs (raw and functionalised). The A549 cells were exposed to MWCNTs (2 µg mL^-1) for 36 days. Periodically, cellular dehydrogenases, pyruvate dehydrogenase kinase 1 (PDK1), cytochrome c release, permeability transition pore (mPTP) opening, transmembrane potential (Δψ m), apoptotic cells, and intracellular ROS were measured. The results, compared to untreated cells and to positive control formed by cells treated with MWCNTs (20 µg mL^-1), highlighted the efficiency of homeostasis to counteract ROS overproduction, but a restitutio ad integrum of mitochondrial functionality was not observed. Despite the tendency to restore, the mitochondrial impairment persisted. Overall, the results underlined the tissue damage that can arise following sub-chronic exposure to MWCNTs.

We have established earlier a cell line from the human limbal area to study cell growth and response to the toxic effects of antibiotics used in ophthalmology. In the recent work, the effect of multi-walled carbon nanotubes (MWCNTs) in cornea damage was investigated in vitro and in vivo in mice. In the in vitro experiments, the physiological effects of multi-walled carbon nano-tube (MWCNT) bundles on corneal wound healing were mimicked in vitro by a reepithelization limbal stem cell model. Murine in vivo experiments were performed with intact, non-functionalized MWCNTs to confirm the validity of in vitro tests. The MWCNTs of 10 -30 nm outer diameter at low concentration (5 µg/ml) did not interfere with the wound healing of the damaged limbal cell monolayer. Higher than 50 µg/ml concentrations: a) generated MWCNT aggregates, b) restrained the movement and prolonged the time of wound healing, c) increased the amplitudes of the oscillations of the cells, and d) resulted in scar formation affecting both cor-neal function and refraction. Chromatin condensation, a sensitive test of the viability of cells, including limbal stem cells revealed that the presence of a low concentration of nanotubes (5 µg/ml), did not significantly affect the viability of limbal cells. Chromatin condensation was completed and metaphase chromosomes were seen at higher MWCNT concentration proving that their aggregates did not affect the viability of limbal cells. This concentration of MWCNTs (5 µg/ml) did impact neither the reepithelization in vitro nor in vivo in the scratched eyes of mice. Scar formation took place at higher than 50 µg/ml concentrations and the healing of the cornea was prevented by the lack of movement of increasingly larger macroaggregates. In vivo murine experiments vali-dated in vitro monolayer regrowth followed by time-lapse microscopy portraying realistically the reepithelization of the damaged cornea that process was gradually slowed down by macro aggregate formation and caused the scarring of the cornea.

Multi-walled carbon nanotubes are engineered nanomaterials (ENMs) that have a fiber-like structure which may be a concern for the development of cellular senescence. Premature senes-cence, a state of irreversible cell cycle arrest, is implicated in the pathogenesis of chronic lung dis-eases such as pulmonary fibrosis (PF). However, the crosstalk between downstream pathways mediating fibrotic and senescent responses of MWCNTs is not well defined. Here, we exposed human bronchial epithelial cells (BEAS2B) to MWCNTs for up to 72 hours and demonstrate that MWCNTs increase reactive oxygen species production (ROS) accompanied by inhibition of cell growth and proliferation. In addition, exposure resulted in the increase of p21 protein and senes-cence associated β-galactosidase (SA β-gal) activity. We also determined that co-exposure with the cytokine, transforming growth factor-β (TGF-β) exacerbated cellular senescence indicated by increased protein levels of p21, p16, and γH2A.X Furthermore, the production of fibronectin and plasminogen activator inhibitor (PAI-1) was significantly elevated with the co-exposure compared to MWCNTs or TGF-β alone. Together, this suggests that the senescence potential of MWCNTs may be enhanced by pro-fibrotic mediators in the surrounding microenvironment.

The present investigation deals with the adsorption of chromium(III) from alkaline media using multi-walled carbon nanotubes. The adsorption of Cr(III) has been studied under various experimental conditions: stirring speed of the aqueous solution, initial metal and adsorbent concentrations, NaOH concentration in the aqueous solution, and temperature. The rate law indicated that chromium adsorption is well represented by the particle diffusion model, whereas the adsorption process fits to the pseudo-second order kinetic model within an exothermic character. Equilibrium data fit to the Langmuir type-2 equilibrium isotherm in an spontaneous process. Chromium(III) can be eluted from metal-loaded nanotubes using acidic solutions, from which fine chromium(III) oxide pigment can be ultimately yielded.

Multi-walled carbon nanotubes (MWCNTs) and graphene oxide (GO) reinforced carbon foam (CF) composite were prepared by direct pyrolysis of MWCNTs, GO and mesophase coal tar pitch. The effect of additive amount of the mixture of MWCNTs and GO on the microstruture and properties of carbon foam was analzyed by transmission electron miscroscopy (TEM), scanning electron microscopy (SEM), X-ray diffraction (XRD), Four-probe resistance meter, universal testing machine, and laser thermal conductivity tester respectively. The result shows that MWCNTs and GO had significant impact on the microstructure of carbon foam. Futhermore, the electrical, mechanical and thermal properties of carbon foam composites were significantly enhanced by increasing the additive amount. Maximum compressive strenght of 19.2 MPa and Young’s modulus of 56.8 MPa of CF composite were observed. Similarly, Highest thermal conductivity of 30.91 W/m.K and electrical conductivity of 27.2 ×103 S/m were observed at 2 wt. % of MWCNTs-GO additive loading.

The present study reports on the fabrication and performance of ammonia sensors based on single-walled carbon nanotubes (SWCNTs) coated with gold nanoparticles (AuNPs). The sensors were subjected to controlled concentrations of ammonia at two temperatures, namely 25 oC and 140 oC, and their response was monitored through successive cycles of ammonia exposure and nitrogen purging. The results demonstrate that the sputtering-based deposition of AuNPs on SWCNTs led to the best sensor performance, characterized by a rapid increase in resistance values upon exposure to ammonia, and efficient recovery at 140 oC. By contrast, the sensor with chemically impregnated AuNPs exhibited a slower response time. Furthermore, a novel device was developed that combined MoS2-AuNPs (sputtering)-SWCNTs, and it showed improved sensor performance compared to the devices with only AuNPs. Overall, the study provides valuable insights into the fabrication and optimization of SWCNT-based ammonia sensors for various applications, especially for detecting and quantifying small amounts of ammonia (concentrations below 1 ppm).

Imperfection sensitivity of large amplitude vibration of curved single-walled carbon nanotubes (SWCNTs) is considered in this study. The SWCNT is modeled as a Timoshenko nano-beam and its curved shape is included as an initial geometric imperfection term in the displacement field. Geometric nonlinearities of von Kármán type and nonlocal elasticity theory of Eringen are employed to derive governing equations of motion of nano-beam. Spatial discretization of governing equations and associated boundary conditions is performed using differential quadrature (DQ) method and the corresponding nonlinear eigenvalue problem is iteratively solved. Effects of value and location of the geometric imperfection, and the nonlocal small-scale parameter on the nonlinear frequency ratio and imperfection sensitivity of a curved SWCNT for various boundary conditions are investigated. The results show that the geometric imperfection plays a significant role in the nonlinear vibration characteristics of curved SWCNTs.

In this paper, a novel nonlocal strain gradient anisotropic elastic shell model is developed to analyse the vibrations of simply supported single‒walled carbon nanotubes (SWCNTs). Sanders‒Koiter shell theory is used to obtain the strain‒displacement relationships. Eringen nonlocal elasticity theory and Mindlin strain gradient theory are adopted to derive the constitutive equations, where the anisotropic elastic constants are expressed via Chang molecular mechanics model. The complex variable method is used to analytically solve the equations of motion and to obtain the natural frequencies of SWCNTs. First, the anisotropic elastic shell model is validated via comparisons with the results of molecular dynamics simulations reported in the literature. Then, the effect of nonlocal and material parameters on the natural frequencies of SWCNTs with different geometries and wavenumbers is analysed. From the numerical simulations it is obtained that the natural frequencies decrease with increasing nonlocal parameter, while they increase with increasing material parameter. Moreover, the decrease of natural frequencies with increasing SWCNT radius is exponential as the material parameter increases, while it is linear as the nonlocal parameter increases. Finally, as the number of waves increases, the natural frequencies linearly vary with increasing nonlocal parameter, while they exponentially increase with increasing material parameter.

In this paper, a kind of single-walled carbon nanotube nonlinear model is developed, and the strongly nonlinear dynamic characteristics of such carbon nanotubes subjected to random magnetic field are studied. The nonlocal effect of microstructure is considered based on the theory of nonlocal elasticity. The natural frequency of the strongly nonlinear dynamic system is obtained by the energy function method, the drift coefficient and the diffusion coefficient are verified. The stationary probability density function of the system dynamic response is given and the fractal boundary of the safe basin is provided. Theoretical analysis and numerical simulation show that stochastic resonance occurs when varying the random magnetic field intensity. The boundary of safe basin has fractal characteristics and the area of safe basin decreases when the intensity of the magnetic field permeability increases.

In the recent years, tubular nanostructures have been related with immense advances in various fields of science and technology. Considerable research efforts have been centered on the theoretical prediction and manufacturing of non-carbon nanotubes (NTs), which meet modern requirements for the developing of novel devices and systems. In this context, diatomic inorganic nanotubes formed by atoms of elements from the 13th group of the periodic table (B, Al, Ga, In, Tl) and nitrogen (N), have received much research attention. In the present work, the elastic properties of single-walled boron nitride, aluminium nitride, gallium nitride, indium nitride and thallium nitride nanotubes were numerically evaluated using the nanoscale continuum modelling approach (also called molecular structural mechanics). The elastic properties (rigidities, surface Young´s and shear moduli, and Poisson´s ratio) of nitride nanotubes are discussed with respect to the bond length of the corresponding diatomic hexagonal lattice. The results obtained contribute to a better understanding of the mechanical response of nitride compound-based nanotubes, covering a broad range from the well-studied boron nitride NTs to the hypothetical thallium nitride NTs.

Our work uses Iterative Boltzmann Inversion (IBI) to study the coarse-grained interaction between 20 amino acids and the representative carbon nanotube CNT55L3. IBI is a multi-scale simulation method that has attracted the attention of many researchers in recent years. It can effectively modify the coarse-grained model derived from the Potential of Mean Force (PMF). IBI is based on the distribution result obtained by All-Atom molecular dynamics simulation, that is, the target distribution function, the PMF potential energy is extracted, and then the initial potential energy extracted by the PMF is used to perform simulation iterations using IBI. Our research results have gone through more than 100 iterations, and finally, the distribution obtained by coarse-grained molecular simulation (CGMD) can effectively overlap with the results of all-atom molecular dynamics simulation (AAMD). In addition, our work lays the foundation for the study of force fields for the simulation of the coarse-graining of super-large proteins and other important nanoparticles.

In the present paper, the comparison is conducted between three classical shell theories as applied to the linear vibrations of single-walled carbon nanotubes (SWCNTs); specifically, the evaluation of the natural frequencies is conducted via Donnell, Sanders and Flügge shell theories. The actual discrete SWCNT is modelled by means of a continuous homogeneous cylindrical shell considering equivalent thickness and surface density. In order to take into account the intrinsic chirality of carbon nanotubes (CNTs), a molecular based anisotropic elastic shell model is considered. Simply supported boundary conditions are imposed and complex method is applied to solve the equations of motion and to obtain the natural frequencies. Comparisons with the results of molecular dynamics simulations available in literature are performed to check the accuracy of the three different shell theories, where Flügge shell theory is found to be the most accurate. Then, a parametric analysis evaluating the effect of diameter, aspect ratio and number of waves along the longitudinal and circumferential directions on the natural frequencies of SWCNTs is performed in the framework of the three different shell theories. Assuming the results of Flügge shell theory as references, it is obtained that Donnell shell theory is not accurate for relatively low longitudinal and circumferential wavenumbers, for relatively low diameters and for relatively high aspect ratios. On the other hand, it is obtained that Sanders shell theory is very accurate for all the considered geometries and wavenumbers, and therefore it can be correctly adopted instead of the more complex Flügge shell theory for the vibration modelling of SWCNTs.

Carbon nanotubes (CNTs) can be considered as semi-rigid all-carbon polymers. However, unlike conventional polymers that can form 3D networks such as hydrogels or elastomers through crosslinking with each other in solution, the cylindrical carbon lattice of CNTs was not believed to be directly crosslinkable in solution until our recent discovery of UV-defluorination driven direct CNT crosslinking. In this study, we further reveal that the UV-defluorination-driven crosslinked CNTs are metastable and can decompose more readily than fluorinated or pristine CNTs upon exposure to Raman laser irradiation. Specifically, we investigate the stability of UV-defluorinated single-walled and multi-walled fluoro-nanotubes using Raman spectroscopy under controlled varying laser power. The results indicate that both the defluorinated single-walled and multi-walled CNTs are thermally less stable than pristine CNTs or untreated fluorinated CNTs, which can be attributed to the strains on the crosslinking bonds created from the curved carbon lattice of linked CNTs. This instability, particularly evident under high-power laser irradiation, leads to combustion processes ignited at relatively lower temperatures that cause an extended burned area centered on the laser spot, offering potential future applications as mechanically robust, lightweight materials with feasible post-use degradation options.

As a member of smart materials, electrorheological elastomers (EREs) formed by pre-treating active electrorheological particles are attracting more and more attention. In this work, four Mg-doped strontium titanate particles with spherical, dendritic, flake-like and pinecone-like morphorlogies were obtained by hydrothermal and low-temperature co-precipitation. XRD, SEM, Raman and FT-IR were used to characterize the obtained products. The results showed that the sizes of Mg-doped strontium titanates are about 1.5‒2.0 μm, and the phase structure are dominated by cubic crystal. These Mg-doped strontium titanates were dispersed in a hydrogel composite elastic medium. Then, Mg-doped strontium titanate/glycerol/gelatin electrorheological composite hydrophilic elastomers were obtained with or without electric field. The electric field response properties of Mg-doped strontium titanate composite elastomers were investigated. It concluded that dendritic Mg-doped strontium titanate composite elastomers is high-performance EREs. And the maximum value of energy storage modulus of Mg-doped strontium titanate composite elastomers has achieved 8.70 MPa. This high electrorheological performance of the products is helpful for their applications in vibration control, force transducers, smart structures, dampers, and other fields.

.Functionalization of multi-walled carbon nanotubes (MWNTs) surface with sulfonated poly(ether ether ketone) SPEEK chains using hexane diamine (HAD) as the interlinking molecule was investigated. MWNTs were first oxidized by nitric acid to generate carboxyl groups on their surface. Grafting of SPEEK chains on the MWNTs surface was achieved using hexane diamine as a cross-linking molecule. The attachment took place after the reaction of amine groups with carboxyl groups of oxidized MWNTs and sulfonate groups of SPEEK as confirmed by infrared (FTIR) analysis. Scanning electron microscopy (SEM) showed that MWNTs were packed into a dense and compact structure. Transmission electron microscopy (TEM) showed that the nanotubes were wrapped by polymer chains and arranged in a bundle like structure. These observations reveal that some of MWNTs were interconnected by SPEEK chains.

In this study, the mechanical and piezoresistive properties of mortars reinforced with carbon nanotubes (CNTs) and carbon micro fibers (CMFs) are determined. Silica fume as well as a polymer with polyalkylene glycol graft chains were used as dispersant agents for the CNTs and CMFs incorporation into the cement paste. The mechanical properties of the mortar composites were investigated in respect to their flexural and compressive strength. A four-probe method was used for the estimation of their piezoresistive response. The test outcomes revealed that the combination of the dispersant agents along with a low content of CNTs and CMF by weight of cement (bwoc) result in the production of a stronger mortar with enhanced mechanical performance and durability. More specifically, there was an increase in flexural and compressive strength up to 38% and 88%, respectively. Moreover, the piezoresistive response of the reinforced cementitious materials was attributed to the variation of electrical resistivity due to tunneling transport of electrons stemming from two different mechanisms due to the incorporation of the conductive admixtures (CNTs and CMF). This work aims to contribute to the progress acceleration in the field of developing structural materials with self-sensing and electrical actuation related properties.

The rational design of magnetic carbon composites, encompassing both composition and microstructure, holds significant potential for achieving exceptional electromagnetic wave absorbing materials (EAMs). In this study, FeCo@CM composites was efficiently fabricated through an advanced microwave plasma assisted reduction chemical vapor deposition (MPARCVD) technique, offering high efficiency, low cost, and energy-saving benefits. By depositing graphitized carbon microspheres, the dielectric properties were significantly enhanced, resulting in improved electromagnetic wave absorption performances through optimized impedance matching and a synergistic effect with magnetic loss. A systematic investigation revealed that the laminar-stacked structure of FeCo exhibited superior properties compared to its spherical counterpart, supplying a higher number of exposed edges and enhanced catalytic activity, which facilitated the deposition of uniform and low-defect graphitized carbon microspheres. Consequently, the dielectric loss performance of the FeCo@CM composites was dramatically improved due to increased electrical conductivity and the formation of abundant heterogeneous interfaces. At a 40 wt% filling amount and a frequency of 7.84 GHz, the FeCo@CM composites achieved a minimum reflection loss value of -58.2 dB with an effective absorption bandwidth (fE) of 5.13 GHz. This study presents an effective strategy for developing high-performance EAMs.

While significant efforts have been made to recycle metals like lithium or cobalt for sustainable development in the battery industry, other high-value materials in the renewable energy sector, such as fluorinated carbon nanotubes (FCNTs), have not been adequately explored for re-utilization after their quality has been downgraded. FCNTs are expensive and energy-intensive to produce, making their sustainable use crucial. This study explores the potential of reusing quality-downgraded fluorinated carbon nanotubes (QD-FCNTs) as eco-friendly nano-additives in microgel composites for water retention applications. By employing a surface treatment process that avoids additional energy costs and environmentally harmful chemicals, we successfully enhanced the interaction between QD-FCNTs and microgels. This treatment significantly improved water retention time by reducing rapid evaporation, enabling sustained water release. Our findings demonstrate a promising avenue for the sustainable application of quality-downgraded fluorinated carbon nanotubes in agricultural and environmental technologies.

Nanoparticles (NPs) have various applications in medicine, cosmetics, optics, catalysis, environmental purification, and other areas nowadays. With an increasing annual production of NPs, the risks of their harmful influence to the environment and human health is rising. Currently, our knowledge about the mechanisms of interaction between NPs and living organisms is limited. Additionally, poor understanding of how physical and chemical characteristic and different conditions influence the toxicity of NPs restrict our attempts to develop the standards and regulations which might allow us to maintain the safe living conditions. The marine species and their habitat environment are under continuous stress due to anthropogenic activities which result in the appearance of NPs in the aquatic environment. Our study aimed to evaluate and compare biochemical effects caused by the influence of different types of carbon nanotubes, carbon nanofibers, and silica nanotubes on four marine microalgae species. We have evaluated the changes in growth-rate, esterase activity, membrane polarization, and size changes of microalgae cells using flow cytometry method. Our results demonstrated that toxic effects caused by the carbon nanotubes strongly correlated with the content of heavy metal impurities in the NPs. More hydrophobic carbon NPs with less ordered structure had a higher impact on the red microalgae P. purpureum because of higher adherence between the particles and mucous covering of the algae; silica NPs caused significant inhibition of microalgae growth-rate predominantly produced by mechanical influence.

The dopamine and uric acid are primary products of purine metabolism and they coexist in serum and the extracellular fluid of the central nervous system. Some diseases of the human body are due to abnormal levels of uric acid and dopamine. Thus, the clinical diagnosis of some diseases needs a sensitive and simultaneous analysis of uric acid and dopamine. In this study, a novel conductive composite film containing multi-walled carbon nanotubes (MWTs) with cooper phthalocyanine attached to acrylate polymer (MWCNTs-CuMAPC-PnBA) was fabricated and dropped on a glassy carbon electrode and used for the simultaneous determination of Uric Acid (UA) and dopamine (DA). The modified glassy carbon electrode showed satisfactory electrocatalytic activity toward dopamine and uric acid. Low detection limits were achieved at 0.174 µM of DA and 6.87 µM of UA and the linear detection ranges of DA and UA are 5-200 µM and 20-250 µM respectively. The proposed sensing system based on the modified GCE offers promising results for rapid, cost-effective and selective simultaneous detection of uric acid and dopamine. Also, the complex modified electrode showed satisfactory results to detecting simultaneously UA and DA in real human samples (human Urine) via the standard addition method.

Carbon nanotubes have been attracting considerable interest among material scientists, physicists, chemists and engineers for almost 30 years. Owing to their high aspect ratio, coupled with remarkable mechanical, electronic and thermal properties, carbon nanotubes have found application in diverse fields. In this review, we will cover the work on carbon nanotubes used for sensing applications. In particular, we will see examples where carbon nanotubes act as main players in devices sensing biomolecules, gas, light or pressure changes. Furthermore, we will discuss how to improve the performance of carbon nanotube-based sensors after proper modification.

The article offers a comprehensive overview of recent breakthroughs in eco-friendly polymers and polymer composites, underscoring their pivotal role in addressing sustainability challenges across diverse industrial sectors. Despite encountering obstacles related to performance and processability, biopolymers sourced from renewable materials emerge as promising alternatives for the plastics that are currently used by human beings. Natural fillers are highlighted as a strategic avenue for crafting sustainable composites, with residual natural fillers being particularly explored. Heightened environmental concerns propel discussions on the criticality of integrating biodegradable materials with natural fillers, underlining the urgency for clear frameworks and financial incentives to support adoption of these materials. Additionally, the article examines the potential of biodegradable polymers and polymer composites, with a specific emphasis on the utilization of polyhydroxyalkanoate (PHA) in composite materials and its market prospects. Moreover, it emphasizes the indispensable need for ongoing research and development endeavors to address environmental challenges within the polymer sector, reflecting a mounting interest in sustainable materials across industries.

Sulfate attack is one of the main factors affecting the durability of concrete structures. In recent years, multi-walled carbon nanotubes (MWCNTs) have attracted the attention of scholars for their excellent mechanical properties and durability performance. In this paper, the influence of sulfate attack and dry-wet cycles on the performance of multi-walled carbon nanotube-lithium slag concrete (MWCNTs-LSC) with varied MWCNTs content (0wt%, 0.05wt%, 0.10wt% and 0.15wt%) and varied water-cement ratios (0.35, 0.40 and 0.45) were investigated. Besides, scanning electron microscopy (SEM) and X-ray computed tomography (CT) tests were conducted to analyze the microstructure and pore structure of the concrete. The results show that concrete incorporated with MWCNTs could effectively mitigate sulfate attack The resistance to sulfate attack of concrete is negatively related to the water-cement ratio when the dry-wet cycle is fixed. The MWCNTs-LSC showed the best compressive strength at the water-cement ratio of 0.35 and 0.10 wt% MWCNTs. The SEM test results showed that the MWCNTs both filled the pores and cracks within the specimen and formed bridges between the cracks, enhancing the resistance to sulfate attack. The CT test results also showed that the addition of MWCNTs could reduce the porosity of concrete, refine the pore size and inhibit the generation and development of cracks, thus optimizing the internal structure of concrete and improving its resistance to sulfate attack.

In this paper, carbon nanotubes modified screen-printed electrode (CNTs/SPE) was prepared and the CNTs/SPE was employed for the electrochemical determination of antioxidant substance Chlorogenic acids (CGAs). A pair of well-defined redox peak of CGA was observed at the CNTs/SPE in 0.10 mol∙L^-1 acetic acid-sodium acetate buffer (pH 6.2) and electrode process is adsorption-controlled. Cyclic voltammetry (CV) and differential pulse voltammetry (DPV) method for the determination of CGA were proposed based on the CNTs/SPE. Under the optimal conditions, the proposed method exhibited linear ranges from 4.73×10^-7 to 4.45×10^-5 mol∙L^-1, the linear regression equation was Ipa(µA) = 4.1993 C (mol∙L^-1)+1.1039 (r = 0.9976) and the detection limit for CGA could reach 3.25×10^-6 mol∙L^-1. The recovery of matrine was 94.74~106.65% (RSD = 2.92%) in coffe beans. The proposed method is quick, sensitive, reliable, and can be used for the determination of CGA.

The influence of short term water absorption on the mechanical properties of halloysite nanotubes-multi layer graphene reinforced polyester hybrid nanocomposites has been investigated. The addition of nano-fillers significantly increased the flexural strength; tensile strength and impact strength in dry and wet conditions. After short term water exposure; the maximum microhardness; tensile; flexural and impact toughness values were observed at 0.1 wt% MLG. The microhardness increased up to 50.3%; tensile strength increased up to 40% and flexural strength increased up to 44%. Compared to dry samples; the fracture toughness and surface roughness of all types of produced nanocomposites were increased that may be attributed to plasticization effect. Scanning electron microscopy revealed that the main failure mechanism is caused by the weakening of nano-filler-matrix interface induced by water absorption. It was further observed that synergistic effects were not effective at concentration of 0.1 wt% to produce considerable improvement in mechanical properties of produced hybrid nanocomposites.

Livestock farming plays a crucial role in agriculture and is important in meeting people's needs for a better life in the new era. However, due to China's "double carbon" target, the development of animal husbandry has been affected by the level of carbon emissions. To study the spatial dis-tribution and dynamic evolution of livestock carbon emissions in Shandong Province, we used panel data from 16 prefecture-level cities in Shandong Province from 2001 to 2022 to determine the spatial differentiation of livestock carbon emissions in Shandong Province and their dynamic evolution by combining spatial and non-parametric estimation methods based on livestock carbon emissions and livestock emission intensity measured by city. The results of the study show that the distribution of carbon emissions from animal husbandry in Shandong Province is in a "dis-persed-aggregated" pattern, and the intensity of carbon emissions shows a gradual downward trend, with a ladder-like distribution characterized by high in the west and low in the east. Through the analysis of the dynamic evolution of nuclear density, we observe that the regional differences of animal husbandry carbon emissions in Shandong Province are expanding, showing the characteristics of polarization. The difference of carbon emissions in the peninsula is gradually narrowing, and the phenomenon of polarization is weakening. The carbon emissions of animal husbandry in the central and western regions of Shandong are polarized.

Nanomedicine has allowed for emerging advances in imaging, diagnostics and therapeutics. Regenerative Medicine has taken advantage of a number of nanomaterials for reparation of diseased or damaged tissues in the nervous system involved in memory, cognition and movement. Electrical, thermal, mechanical and biocompatibility aspects of carbon-based nanomaterials (nanotubes, graphene, fullerenes and their derivatives) make them suitable candidates to drive nerve tissue repair and stimulation. This review article focuses on recent advances on the use of carbon nanotube (CNT)-based technologies on nerve tissue engineering; outlining how neurons interact with the nanomaterials interface for promoting neuronal differentiation, growth and network reconstruction for their possible use in therapies of neurodegenerative pathologies and spinal cord injuries.

The main objective of this work is to study the effects of carbon nanotubes (CNT) on the strength and electrical properties of cement mortar. Molecular dynamic simulations (MDS) were carried out for the mechanical and electrical properties of the cementitious composite and the associated mechanisms. To model the atomic structure of the Calcium-Silicate-Hydrates (C-S-H) gel, tobermorite 11Å was chosen. Single-walled carbon nanotubes (SWCNTs) embedded in tobermorite structure were tested numerically. In particular, the effect of the concentration of CNT in cement paste was studied. An innovative experiment of electrical characterization of a cementitious composite of carbon nanotubes has been developed.

Lake sediment records are of great importance for understanding the evolution of watershed environments. Various studies have been carried out to constrain the depositional ages of lake sediments and examine their physical, chemical, and biological characteristics, aiming to construct historical vegetation, environment and climate patterns in Chinese lake watersheds. In this study, we obtained relevant literature on lake sediment records by searching the key word 'age-depth' from the databases – Web of Science and China National Knowledge Infrastructure (CNKI, the largest Chinese academic database). We analyzed the literature based on its type (published in a Chinese/English journal or as a Master’s/PhD thesis), period of publication, journal (if published in a journal), key authors, study area, dating scale, and main aims. The results suggest that the lakes in the plateau regions are the most popular research topic typically covering 100–200 years (short-term) and 500–30,000 years (long-term). The literature focuses on a wide range of topics, from past environmental evolution in the watershed to lake ecology, and provides a solid foundation for better understanding regional climate change and the preservation of lake environments and ecosystems. In the future, resulting data from environmental reconstruction with lake sediments will be needed to integrate with emerging information processing technologies (e.g., artificial intelligence and meta-analysis), to disentangle the complex interplay between Earth surface processes and global climate change; furthermore, strengthening interdisciplinary collaboration will deepen our comprehension of man-land relationship and promote the sustainable management of lake ecosystems in the context of global climate change.

Asymmetric lithium salts, such as Lithium (difluoromethanesulfonyl)(trifluoromethanesulfonyl)imide (LiDFTFSI), have been demonstrated to surpass traditional symmetric lithium salts with improved Li+ conductivity and the capacity to generate stable solid electrolyte interphase (SEI) while maintaining compatibility with aluminum (Al0) current collector. However, the intrinsic reductive mechanism through which LiDFTFSI influences battery performance remains unclear and under debate. Herein, the detailed SEI reactions of LiDFTFSI-based electrolytes were investigated by combining density functional theory and molecular dynamics, aiming to clarify the formation process and atomic structure of SEI. Our results show that asymmetric DFTFSI– weakens the interaction between carbonate solvents and Li+, and substantially alter the solvation structure, exhibiting a well-balanced coordination capacity to bis(trifluoromethanesulfonyl)imide (TFSI–). Nanoseconds hybrid molecular dynamics simulation further reveals that the preferential decomposition of LiDFTFSI produces sufficient LiF and Li2O to facilitate a robust SEI. Moreover, the abundant F– generated from LiDFTFSI decomposition accumulates on the Al surface and subsequently combines with Al3+ from the current collector to form AlF3, potentially inhibiting corrosion of the current collector. Overall, these findings elucidate how LiDFTFSI regulates the solvation sheath and SEI structure, advancing the development of high-performance electrolytes compatible with current collector.

This investigation explores the potential of enhancing aqueous zinc-ion batteries (AZIBs) through the introduction of a novel cathode material, NH4V4O10 (NVO), combined with reduced graphene oxide (rGO). Utilizing Density Functional Theory (DFT), it was hypothesized that the incorpora-tion of rGO would increase the interlayer spacing of NVO and diminish the charge transfer in-teractions, thus promoting enhanced diffusion of Zn2+ ions. These theoretical predictions were substantiated by experimental data acquired from hydrothermal synthesis, which indicated a marked increase in interlayer spacing. Significantly, the NVO-rGO composite exhibits remarkable cyclic durability, maintaining 95% of its initial specific capacity of 507 mAh g−1 after 600 cycles at a current density of 5 A g−1. The electrochemical performance of NVO-rGO not only surpasses that of pristine NVO but also outperforms the majority of existing vanadium oxide cathode materials reported in the literature. This study underscores the effective integration of theoretical insights and experimental validation, contributing to the advancement of high-performance energy storage technologies.

This study explores the enhancement of aqueous zinc-ion batteries (AZIBs) using ammonium-enhanced vanadium oxide cathodes. Density Functional Theory (DFT) calculations reveal that NH₄⁺ incorporation into V₆O₁₆ lattices significantly facilitates Zn²⁺ ion diffusion by reducing electrostatic interactions, acting as a structural lubricant. Subsequent experimental validation using (NH₄)₂V₆O₁₆ cathodes synthesized via a hydrothermal method corroborates the DFT findings, demonstrating remarkable electrochemical stability with a capacity retention of 90% after 2000 cycles at 5 A g⁻¹. These results underscore the potential of NH₄⁺ in improving the performance and longevity of AZIBs, providing a pathway for sustainable energy storage solutions.

Abstract: Flexible pressure sensors are electronic devices that can be attached to various irregular surfaces to measure the pressure. It is widely used in wearable devices and for health detection. In this study, a general carbon nanotubes/polydimethylsiloxane (CNTs/PDMS) sponge electrode was fabricated as the elementary component of the compressible system. The sensitivity of the flexible pressure sensor is improved by optimizing the preparation process of the conductive sponge and surface modification of the CNTs, and the highest sensitivity reached 71.831 kPa-1(0~2 kPa). The flexible pressure sensor can be used to detect subtle pressure quickly and accurately so that it can be used as wearable sensor to measure the radial artery wave of a human body, which has potential applications in health care and other fields.

Commercially available oxidized (carboxylic groups) and non-oxidized multiwalled carbon nanotubes were studied as adsorbents of cerium(III) in batch operation mode. Several variables affecting the rare earth adsorption were investigated, including: the stirring speed applied to the system, the pH of the solution and the metal concentration and carbon dosages. Although the removal of cerium from the solution is different and dependent upon the adsorbent type: i) adsorption in non-oxidized multiwalled carbon nanotubes, ii) cation exchange in the case of using oxidized multiwalled carbon nanotubes, the adsorption kinetics, the rate law and the isotherm models are the same for both adsorbents: pseudo-second order, film diffusion and Langmuir Type-1, respectively. Cerium is desorbed from loaded adsorbents using acidic solutions.

Herein, we report on a giant thermoelectric figure of merit of a non-degenerate fluorine-doped single-walled carbon nanotube (FSWCNT) using a tractable analytical approach and the phonon lattice Boltzmann model (LBM). We investigate the influence of the doping concentration, and the overlapping integrals on the ZT. The ZT and the temperature range of operation can be tuned using the doping (impurity) concentration and the overlapping integrals, respectively. The lattice thermal conductivity obtained using the phonon LBM was calculated to be 107.2 W/mK which yielded a ZT greater than 20. Interestingly, the ZT obtained is higher than what has been reported in superlattices, (ZT~1.4) and superlattice nanowire, (ZT~ 4) at 300 K, making FSWCNT a potential candidate for thermoelectric applications.

The aim of this work is research dedicated to the search for new bactericidal systems for use in cosmetic formulations, dermocosmetics, or the production of wound dressings. Over the last two decades chitosan due to its special biological activity, has become a highly indispensable biopolymer with very wide application possibilities. Literature reports on the antibacterial effects of chitosan are very diverse, but our research has shown that they can be successfully improved through chemical modification. Therefore, in this study, results on the synthesis of new Schiff bases chitosan – dCsSB-SFD and dCsSB-PCA obtained using two aldehydes: sodium 4-formylbenzene-1,3-disulfonate (SFD) and 2-pyridine carboxaldehyde (PCA) respectively. Chitosan derivatives synthesized in this way demonstrate stronger antimicrobial activity. Carrying out the procedure of grafting chitosan with a caproyl chain allowed obtaining compatible blends of chitosan derivatives with κ-carrageenan, which are stable hydrogels with a high swelling coefficient. Furthermore, covalently bounded PCL improved the solubility of obtained polymers in organic solvents. With this respect, the Schiff base-containing polymers obtained in this study, with special hydrogel and antimicrobial properties are very promising materials for the potential use as a controlled-release formulation of both, hydrophilic and hydrophobic drugs in cosmetic products for skin health.

This study presents the synthesis and electrochemical evaluation of nitrogen-doped vanadium oxide (N-V2O3/C) as a cathode material for aqueous zinc-ion batteries (AZIBs), using a hydrothermal method. Compared to undoped V2O3/C, N-V2O3/C exhibits enhanced electrical conductivity, capacity, and electrochemical kinetics, attributed to the incorporation of pyridinic and pyrrolic nitrogen. Initial charge-discharge cycles indicate phase transitions to amorphous vanadium oxides, enhancing conductivity. N-V2O3/C shows a high specific capacity of 168.4 mAh g−1 at 10 A g−1 and remarkable reversibility, highlighted by the transient existence of intermediate species during cycling. Optimal electrochemical performance is achieved with a vanadium to nitrogen molar ratio of 2:3, indicating the significant impact of nitrogen doping concentration on the material’s efficiency. This work underscores the potential of N-V2O3/C as a superior cathode material for AZIBs.

Using density functional theory (DFT), the density of states of NH4V3O8 (NVO) was analyzed pre and post-oxygen defects (Od) formation. The findings revealed a reduced bandgap in NVO after Od introduction, emphasizing the role of Od in enhancing conductivity of the material, thus improving its electrochemical attributes. Through the water bath method, both NVO and its oxygen-deficient counterpart, (NH4)2V10O25⸱8H2O (NVOd), were synthesized as potential cathode materials for aqueous zinc-ion batteries (AZIBs). Experimental outcomes resonated with DFT predictions, highlighting the beneficial role of oxygen defects in boosting electrical conductivity. Notably, the refined material displayed a remarkable capacity of 479.3 mAh g-1 at 0.1 A g-1, underscoring its promise for advanced energy storage solutions.

Single-molecule magnets (SMMs) have garnered significant interest in the field of molecular magnetism due to their unique magnetic properties at the nanoscale. These molecular systems exhibit magnetisation behaviour reminiscent of conventional bulk magnets but with distinct advantages such as size-dependent properties and potential applications in quantum computing and high-density data storage. However, challenges remain in harnessing their properties for practical applications, including their susceptibility to degradation and limited control over their assembly and organisation.

Media thermal conductivity is important in various heat-transfer processes. Many conventional fluid conductors suffered low conductivity and environmental issues. Therefore, researchers developed efficient aqueous nanofluid conductors. Carbon nanotubes (CNTs) are widely studied to reach efficient, stable, low-cost and environmentally-friendly aqueous-nanofluids. This review provides a clear understanding of how CNTs improve thermal conductivity of aqueous nanofluids. A qualitative model is presented to explain literature mechanisms behind improvement. CNT type effects are discussed with other factors such as aspect ratio, Reynold number, dispersion quality, composition, temperature and additives. CNT functionalization is described. Relations to estimate nanofluid thermal conductivity are discussed. The model will help specialists to tailor CNT aqueous nanofluids as desired.

Carbon nanotubes (CNTs) possess unique mechanical, physical, electrical and absorbability properties coupled with their nanometer dimensional scale that renders them extremely valuable for applications in many fields including nanotechnology and chromatographic separation. The aim of this review is to provide an updated overview about the applications of CNTs in chiral and achiral separations of pharmaceuticals, biologics and chemicals. Chiral SWCNTs and MWCNTs have been directly applied for the enantioseparation of pharmaceuticals and biologicals by using them as stationary or pseudostationary phases in chromatographic separation techniques such as high-performance liquid chromatography (HPLC), capillary electrophoresis (CE) and gas chromatography (GC). Achiral MWCNTs have been used for achiral separations as efficient sorbent objects in solid-phase extraction techniques of biochemicals and drugs. Achiral SWCNTs have been applied in achiral separation of biological samples. Achiral SWCNTs and MWCNTs have been also successfully used to separate achiral mixtures of pharmaceuticals and chemicals. Collectively, functionalized CNTs have been indirectly applied in separation science by enhancing the enantioseparation of different chiral selectors whereas, non-functionalized CNTs have shown efficient capabilities for chiral separations by using techniques such as encapsulation or immobilization in polymer monolithic columns.

Achieving the thermal conductivity required for efficient heat management in semiconductors and other devices requires the integration of thermally conductive ceramic fillers at concentrations of 60 vol% or higher. However, the increased filler content often negatively affects the mechanical properties of the composite matrix, limiting its practical applicability. To address this issue, in this paper, we present a new strategy to reduce the required ceramic filler content: the use of a thermally conductive ceramic composite filler with carbon nanotubes (CNT) grown on aluminum nitride (AlN). We have combined catalyst coating technology with vacuum filtration to ensure that the catalyst is uniformly applied to micrometer-sized AlN particles, followed by efficient and uniform synthesis of CNTs using a water-assisted process in a vertical furnace. By carefully controlling the number of vacuum filtration cycles and the growth time of the CNTs, we demonstrate precise control over the number and length of the CNT layers, thereby adjusting the properties of the composite to the intended specifications. When AlN/CNT hybrid fillers are incorporated into silicone rubber, while maintaining the mechanical properties of rubber, the thermal diffusivity achieved at reduced filler levels exceeds that of composites using AlN-only or simultaneous AlN and CNTs formulations. This demonstrates the critical role of CNTs on AlN surfaces. Our study represents a significant advancement in the design of thermally conductive materials with potential implications for a wide range of applications.

The normal growth and development of skeletal muscle is essential for the health of the body. The regulation of skeletal muscle by intestinal microorganisms and their metabolites has been continuously revealed. Acetate is the predominant short-chain fatty acid synthesized by gut microbiota through the fermentation of dietary fiber, however, the underlying molecular mechanisms governing the interaction between acetate and skeletal muscle during rapid growth stage remain to be further elucidated; Here, specific pathogen-free (SPF) mice, germ-free (GF) mice, and germ-free mice supplemented with sodium acetate (GS) were used to evaluate the effects of acetate on skeletal muscle growth and development of young mice with gut microbiota deficiency; We found the concentration of serum acetate, body mass gain, succinate dehydrogenase activity and expression of myogenesis maker gene of skeletal muscle in the GS group was higher than GF group following sodium acetate supplement. Furthermore, the transcriptome analysis revealed that acetate activated biological processes regulating skeletal muscle growth and development in GF group that are inhibited due to gut microbiota deficiency. In vitro experiment, we proved that acetate up-regulated Gm16062 to promote skeletal muscle cell differentiation; Overall, our findings proved that acetate promote skeletal muscle growth and development in young mice via increase Gm16062 expression.

High-performance electromagnetic interference (EMI) shielding materials with ultralow density and environment friendly properties are greatly demanded to address electromagnetic radiation pollution. Herein, carbon nanotubes/polylactic acid (CNTs/PLA) materials with different CNTs contents, which exhibit characteristics of light weight, environmental protection and good chemical stability, are fabricated by 3D printing technology, where CNTs are evenly distributed and bind well with PLA. The performances of 3D printed CNTs/PLA composite are improved compared to pure 3D printed PLA composite, which include mechanical properties, conductive behaviors and electromagnetic interference (EMI) shielding. The EMI shielding effectiveness (SE) of CNTs/PLA composite could be improved when the contents of CNTs increase. When it reaches 15 wt%, the EMI SE of 3D printed CNTs/PLA composite could get up to 47.1 dB, which shields 99.998% of electromagnetic energy. Meanwhile, the EMI shielding mechanism of 3D printed CNTs/PLA composite is mainly of absorption loss, and it generally accounted for more than 80% of the total shielding loss. These excellent comprehensive performances endow the 3D printed CNTs/PLA composite with great potential for use in industrial and aerospace area.

A Berry geometrical phase is identified in a strongly metastable system containing dynamically responsive clathrate hydrate structures within a crystal-fluid material. High energy degeneracy in the associated chemistry produces local stability and false vacuum conditions that lead to non-extensive and non-additive contributions in the fundamental thermodynamic relation. Application of Ginzburg-Landau theory and the scaling laws reveals a coherence length and a penetration depth for a macro-scale dual superconductor. The coherence length determines non-extensive volume changes whilst its inverse gives the Higgs mass. The penetration depth determines the extent of QCD vacuum suppression whilst its inverse gives the vector boson mass together with indirect manifestation as non-additive hyperbolic curvature. Simultaneous emergence of the Ginzburg-Landau superconducting phase transition is consistent with gauge-invariant coupling of the scalar field to the Yang-Mills action in QCD. The discovery of an energy gap in the gradient energy term of the system Lagrangian is associated with a critical correlation length revealed in the transition from a gapped to a gapless superconducting state. Together with the emergence and absorption of the Higgs-like scalar field, a mechanism for describing a renormalized QCD mass gap arises.

Since the 1960s Rare earths (REs) applications gradually have expanded to everyday life. REs have great strategic importance in industrial and technological development, so it is expected an increase in their demand. Among the REs the European Commission considered Cerium and Lanthanum as critical raw materials. This research article studies the adsorption of Ce and La onto two carbon nanomaterials, multiwalled carbon nanotubes (MWCNT) and carboxylic functionalized multiwalled carbon nanotubes (MWCNT_ox). The latter has slightly more affinity for REs than MWCNT. The recovery percentage for Ce were 89 and 98% and in the case of for La were 99 and 92% using 0.8 g of MWCNT and 0.2 g of MWCNT_ox respectively. The adsorption process fits a pseudo second-order kinetic model and the Langmuir isotherm best represented the metal uptake.

In recent years, it has been found in engineering practice that the service life of cemented carbide shield machine tools used in uneven soft and hard strata is substantially reduced. The study found that thermal stress is the main reason for the failure of cemented carbide shield tunneling tools when shield tunneling is carried out in uneven soft and hard soil. To maintain the hardness of cemented carbide, improving the thermal conductivity of the shield machine tool is of great importance for prolonging its service life and reducing engineering costs. In this paper, graphene and carbon nanotubes were mixed with WC-Co powder and sintered by SPS (Spark Plasma Sintering). The morphology was observed by using scanning electron microscopy (SEM) and energy dispersive X-ray spectroscopy (EDS). A Rockwell hardness tester and bending strength tester were used to test hardness, bending strength and thermal conductivity. The results show that adding trace graphene or carbon nanotubes can increase the bending strength of the cemented carbide by approximately 50% while keeping the hardness of the cemented carbide unchanged. The thermal conductivity of the cemented carbide can be increased by 10% with the addition of 0.12% graphene alone.

Polymer-based composites represent a separate class of materials in demand by the industry. In comparison with other polymers, UHMWPE is characterized by exceptionally high wear and impact resistance. In this work, compacts were produced from UHMWPE GUR 4120 powder with the addition of Nanoscale Detonation Carbon (NDC) and Single-Walled Carbon Nanotubes (SWCNTs) on a hydro-pneumatic impact device by the Cyclic Impact Compaction (CIC) technique. The obtained samples were subjected to wear resistance test, their hardness and tensile strength were measured. Studies have shown that the addition of NDС and SWCNTs in UHMWPE leads to an increase in hardness by 6.4 and 19.6%, to a decrease in wear by 11.5 and 38.5% and a decrease in the coefficient of friction by 10 and 20%, respectively. However, the tensile strength of UHMWPE decreases by 11.7 and 40.4% and elongation decreases by 11.9 and 30.1% with the addition of NDС and SWCNTs, respectively.

Thermal analysis is widely employed for the characterization of nanomaterials. It encompasses a variety of techniques that allow the evaluation of the physicochemical properties of a material by monitoring its response under controlled temperature. In the case of carbon nanomaterials, such as carbon nanotubes and graphene derivatives, thermogravimetric analysis (TGA) is particularly useful to determine the quality and stability of the sample, presence of impurities and the degree of functionalization or doping after post-synthesis treatments. Furthermore, TGA is widely used to evaluate the thermal stability against oxidation by air, which can be for instance enhanced by the purification of the material and by nitrogen doping, finding application in areas where a retarded combustion of the material is required. Herein, we have evaluated key parameters that play a role in the data obtained from TGA. Within this study we show that the thermogravimetric curve of carbon nanomaterials is greatly influenced by these parameters. This is important in terms of data recording and their analysis, since a poor control of the conditions of measurement might lead to false conclusions. We highlight this by analyzing different samples of graphene and carbon nanotubes where both thermal stability and sample purity assessment are found to be dependent on the employed TGA parameters. Finally, a set of TGA parameters are recommended for the analysis of carbon nanomaterials to obtain reliable data.¡

A study on the dependence of the thermal conductivity of the percolation network of carbon nanotubes (or CNTs) on the type and degree of functionalization has been carried out. The study was focused on the influence of the more commonly used -COOH, -OH and -СОNH2 groups. A non-linear dependence of the conductivity on the number of functional groups has been revealed. A small number of functional groups can improve conductivity, and a large one can impair it. We presuppose the existence of competing processes that increase thermal conductivity (changes in the CNT geometry, improvement of the contact between them) and enhance photon scattering (emergence of defects and scattering centers). The data can be used for controlling the thermophysical properties of the CNTs as well as determining the optimal degree of functionalization during the development of composites and nanodevices.

Multiwalled Carbon Nanotubes (MWCNTs) is more efficient for fabrication modern design of silicone rubber (SR) that used in industrial engineering applications; it has been embedded in room temperature vulcanization silicone rubber (RTV-SR) matrix for controlling in dielectric characterization. Frequency dielectric measurements were performed for multiwalled carbon nanotubes SR/MWCNT nanocomposites. Hence, the dielectric properties of modern design SR/MWCNT nanocomposites has been deduced as experimental work done to clarify the benefit of filling MWCNT with different patterns inside dielectrics. In variant thermal conditions (up to 40oC), it has been investigated that the new behaviors of SR/MWCNT nanocomposites dealing with nanotechnology techniques for designing new dielectric behaviors of insulation materials. Finally, this research succeeded to characterize dielectric constant, electric modulus and dielectric loss of SR/MWCNT nanocomposites with respect to traditional silicon rubber under variant thermal conditions and frequency response analysis (FRA) according to using certain types and concentrations of MWCNTs.

Ultralong carbon nanotubes (UCNTs) are highly demanded for nanocomposites applications because of their magnificent physical and chemical properties. UCNTs are synthesized by catalytic chemical vapor deposition (CCVD) method and, before using as fillers in nanocomposites, should be purified from residual catalyst and non-CNT particles without significant destruction or scissoring of UCNTs. The role of water vapor for purification of UCNTs is investigated, the importance of water assistance in this process is confirmed. It was shown that wet air treatment of products of UCNTs CCVD synthesis under mild conditions can be used to decrease sufficiently residual catalyst content without significant carbon losses in comparison with the results obtained with dry air, while the residual iron content was shown to influence heavily on the subsequent oxidation of different forms of carbons, including UCNTs. The increasing of D/G ratio of Raman spectra after wet air treatment of products of UCNTs CCVD synthesis makes it possible to conclude that iron catalyst particles transform into iron oxides and hydroxides that caused inner structural strains and destruction of carbon shells improving removal of the catalyst particles by subsequent acid treatment. UCNTs purification with water assistance can be used to develop economically and ecologically friendly methods for obtaining fillers for nanocomposites of different applications.

Recent discovery of triangular boron Nanotubes makes it a competitor of carbon in many respects. Closed forms of M-polynomial of nanotubes produce closed forms of many degree-based topological indices which are numerical parameters of the structure and, in combination, determine properties of the concerned nanotubes. In this report, we give M-polynomials of triangular boron nanotubes and recover many important topological degree-based indices of these nanotubes. We also plot surfaces associated to these nanotubes.

Double-walled carbon nanotube-yttria-stabilized ZrO2 nanocomposites are prepared by a mixing route followed by Spark Plasma Sintering. Incorporation of carbon at contents higher than 2 wt.% results in significantly lower friction coefficients, both against alumina and steel balls. Double-walled carbon nanotubes improve wear resistance and reduce friction without severe damage, contrary to multi-walled carbon nanotubes.

The behaviour of oxidized and non-oxidized multiwalled carbon nanotubes in the adsorption of lanthanum(III) from aqueous solutions is described. Metal uptake is studied as a function of several variables such as the stirring speed of the system, pH of the aqueous solution and metal and nanomaterial concentrations. The experimental results are fitted to various kinetics and isotherm models, being the rate law fitted to the film diffusion and particle diffusion models, when the non-oxidized and the oxidized nanomaterials are used to remove lanthanum from the solution, respectively. Sulphuric acid solutions seem to be appropriate to recover the metal from La-loaded nanomaterials.

The preparation of sulfur-single walled carbon nanohorns active material via a simple and sustainable evaporation method for application as cathode in lithium-sulfur batteries is reported. We show that the synthesis process enables the infiltration of elemental sulfur within the carbon nanohorns thus obtaining a morphology responsible for the ameliorating of the shuttle effect. The sulfur-carbon composite is characterized in terms of structure, morphology, and composition through x-ray diffraction, transmission electron microscopy, and thermogravimetric analyses. From the electrochemical point of view, cyclic voltammetry, rate capability, and galvanostatic cycling tests are performed employing a solution of bis(trifluoromethane)sulfonimide lithium salt and lithium nitrate in a mixture of 1,2-dimethoxyethane and 1,3-dioxolane in order to evaluate the electrode design applicability within lithium-sulfur cells. In this respect, further insights are provided by the estimation of the lithium-ion diffusion coefficient through the Randles-Sevcik equation, and by electrochemical impedance spectroscopy. The obtained results reveal a remarkable cycle life lasting around 800 cycles with a stable capacity of 520 mA h g-1 for the first 400 cycles at C/4, while reaching a value around 300 mA h g-1 at the 750th cycle. These results suggest sulfur-carbon nanohorns active material as a potential candidate for the next-generation battery technology.

A simple method is presented for the continuous generation of carbon nanotube forests stably anchored on stainless-steel surfaces using a reactive-roll-to-roll (RR2R) configuration. No addition of catalyst nanoparticles is required for the CNT-forest generation, the stainless-steel substrate itself being tuned to generate the catalytic growth sites. The process enables very larges surfaces covered with CNT forests having individual CNT roots anchored to the metallic ground through primary bonds. Fog water harvesting is demonstrated and tested as one potential application using long CNT-covered wires. The RR2R is performed in the gas phase, no solution processing of CNT suspensions is used contrary to usual R2R CNT-based technologies. Full or partial CNT-forest coverage provides tuning of the ratio and shape of hydrophobic and hydrophilic zones on the surface. This enables optimization of fog water harvesters for droplet capture through the hydrophobic CNT forest, and water removal from the hydrophilic SS surface. Water recovery tests using small harp-type harvesters with CNT-forest generate water capture of up to 2.2 g/cm2h under ultrasound-generated fog flow. The strong CNT root anchoring on the stainless steel surfaces provides opportunities for (i) robustness and easy transport of the composite structure, (ii) chemical functionalization and/or nanoparticle decoration of the structures, and opens the road for a series of applications on large scale surfaces, including fog harvesting.

Titania is one of the most comprehensively studied nanostructures due to its widespread applications in production of catalytic, gas- sensing and corrosion- resistance materials [1]. M-polynomial of nanotubes has been vastly investigated as it produces many degree-based topological indices which are numerical parameters capturing structural and chemical properties. These indices are used in the development of quantitative structure-activity relationships (QSARs) in which the biological activity and other properties of molecules are correlated with their structure like boiling point, stability, strain energy etc of chemical compounds. In this paper, we determine M-polynomials of single-walled titanium (SW TiO2) nanotubes and recover important topological degree based indices of them to theoretically judge these nanotubes. We also use Maple to plot surfaces associated to different types of single-walled titanium (SW TiO2) nanotubes.

The structure and phenomena arising from charge transfer in cold field emission modus in a single closed carbon nanotube under cold field emission conditions were studied. By studying microphotographs in various microscopes - AFM, SEM, TEM it was found inhomogeneities in the form of two types of superlattices. The conductivity of the emitter section of a nanodiode circuit with an emitter made of an individual closed carbon nanotube (CNT) and arrays of closed CNTs was studied. High values of cold field emission were observed, as well as nonlinearity and anomalies of the current-voltage characteristic (I-V characteristics), which manifested themselves in the form of peaks at low and high current values. Peaks in the CVC have distinct areas of negative differential conductivity. It is argued, that the anomalously high currents in the I–V characteristics of cold field emission of electrons from a nanoemitter made of closed CNTs can be associated with a sharp increase in the density of electron states at energies near the van Hove singularity.

Herein, we present a combination of experimental and computational study on the mitochondrial F0F1-ATPase nanotoxicity inhibition induced by single-walled carbon nanotubes (SWCNT-pristine, SWCNT-COOH). To this end, the in vitro inhibition responses in submitochondrial particles (SMP) as F0F1-ATPase enzyme were strongly dependent on the concentration assay (from 3 to 5 µg/ml) for both types of carbon nanotubes. Besides, both SWCNTs show an interaction inhibition pattern like the oligomycin A (the specific mitochondria F0F1-ATPase inhibitor). Furthermore, the best crystallography binding pose obtained for the docking complexes based on the free energy of binding (FEB), fit well with the previous in vitro evidences from the thermodynamics point of view. Following an affinity order as: FEB (oligomycin A/F0-ATPase complex) = -9.8 kcal/mol > FEB (SWCNT-COOH/F0-ATPase complex) = - 6.8 kcal/mol ~ FEB (SWCNT-pristine complex) = -5.9 kcal/mol. With predominance of van der Waals hydrophobic nanointeractions with key F0-ATPase binding site residues (Phe 55 and Phe 64). By the other hand, results on elastic network models, and fractal-surface analysis suggest that SWCNTs induce significant perturbations by triggering abnormal allosteric responses and signals propagation in the inter-residue network which could affect the substrate recognition ligand geometrical specificity of the F0F1-ATPase enzyme in order (SWCNT-pristine > SWCNT-COOH). Besides, the performed Nano-QSTR models for both SWCNTs show that this method may be used for the prediction of the nanotoxicity induced by SWCNT. Overall, the obtained results may open new avenues toward to the better understanding and prediction of new nanotoxicity mechanisms, rational drug-design based nanotechnology, and potential biomedical application in precision nanomedicine.

Developing nanomaterials with the capacity to restrict the growth of bacteria and fungus is of current interest. In this study, nanocomposites of poly(2-hydroxyethyl methacrylate) (PHEMA) and carbon nanotubes (CNTs) functionalized with primary amine, hydroxyl, and carboxyl groups were prepared, and characterized. An analysis by Fourier transform infrared (FT-IR) spectroscopy and X-ray photoelectron spectroscopy showed that PHEMA chains were grafted to the functionalized CNTs. The morphology of the prepared nanocomposites studied by field emission scanning electron microscopy (FE-SEM), and transmission electron microscopy (TEM) shows significant changes with respect to the observed for pure PHEMA. The thermal behavior of the nanocomposites studied by differential scanning calorimetry (DSC) revels that the functionalized CNTs affects strongly the mobility of the PHEMA chains. Tests carried out by thermogravimetric analysis (TGA) were used to calculate the degree of grafting of the PHEMA chains. The ability of prepared nanocomposites to inhibit the growth of the fungus Candida albicans, and the bacteria Staphylococcus aureus, Pseudomonas aeruginosa, Escherichia coli was evaluated. A moderated antifungal and antibacterial capacity of the prepared nanocomposites was determined.

Due to low working temperature, high energy density and low pollution, proton exchange fuel cells have been investigated under different operating conditions in different applications. Using platinum catalysts in methanol fuel cells leads to increasing the cost of this kind of fuel cell which is considered as a barrier to the commercialism of this technology. For this reason, a lot of efforts have been made to reduce the loading of the catalyst required on different supports. In this study, carbon black (CB) and carbon nanotubes (CNT) have been used as catalyst supports of the fuel cell as well as using the double-metal combination of platinum-ruthenium (PtRu) as anode electrode catalyst and platinum (Pt) as cathode electrode catalyst. The performance of these two types of electro-catalyst in the oxidation reaction of methanol has been compared based on electrochemical tests. Results showed that the carbon nanotubes increase the performance of the micro-fuel cell by 37% at maximum power density, compared to the carbon black. Based on thee-electrode tests of chronoamperometry and voltammetry, it was found that the oxidation onset potential of methanol for CNT has been around 20% less than CB, leading to the kinetic improvement of the oxidation reaction. The current density of methanol oxidation reaction increased up to 62% in CNT sample compared to CB supported one, therefore the active electrochemical surface area of the catalyst has been increased up to 90% by using CNT compared to CB which shows the significant rise of the electrocatalytic activity in CNT supported catalyst. Moreover, the resistance of the CNT supported sample to poisonous intermediate species has been found 3% more than CB supported one. According to the chronoamperometry test results, it was concluded that the performance and sustainability of the CNT electro-catalyst show remarkable improvement compared to CB electro-catalyst in the long term.

A new type of low cost, environmentally friendly wood-plastic composites (WPC) containing carbon nanotubes(CNT)of low content 0%, 0.05wt%, 0.1wt% and 0.15wt%, wood fibers of 14wt% and polymer PES of 86wt% was manufactured by the selective laser sintering (SLS) approach of 3D printing. The experimental results showed that the incorporating of CNTs could obviously increase the mechanical properties of the wood/PES composites material. The tensile strength, bending strength and elasticity modulus were 76.3%, 227.9% and 128.7% higher with 0.1wt% CNTs than without CNTs. And the mechanical properties of specimens firstly increased and then decreased with the increasing contents of CNTs. The SEM results of the specimens’ fracture morphology indicated that the preferable bonding interfaces between wood flour grains and PES grains were achieved by adding CNTs to the composites. There are two reasons to explain why the composites possessed the superior mechanical properties: CNTs could facilitate the laser sintering process of wood plastic composites due to their thermal conductivities; also, CNTs could directly reinforce the WPC composites as reinforcement.

For every three people on the planet there is approximately two Tonne (Te) of available plastic waste. We show that carbon recovery from polystyrene (PS) plastic is enhanced by the co-addition to solvents to grow carbon nanotubes (CNTs) by liquid injection chemical vapour deposition. Polystyrene was loaded up to 4 wt% in toluene and heated to 780 °C in the presence of a ferrocene catalyst and a hydrogen/argon carrier gas in a 1:19 ratio. High resolution transmission electron microscopy (HRTEM), scanning electron microscopy (SEM), thermogravimetric analysis (TGA) and Raman spectroscopy were used to identify multi-walled carbon nanotubes (MWCNTs). The PS addition in the range from 0 to 4 wt% showed improved quality and CNT homogeneity; Raman “Graphitic/Defective” (G/D) values increased from 1.9 to 2.3; mean CNT diameters increased from 43.0 to 49.2 nm; and maximum CNT yield increased from 11.3% to 14.2%. Since both the CNT diameters and the percentage yield increased with respect to polystyrene addition, we conclude that carbon from the PS contributes to the carbon within the MWCNTs. The electrical contact resistance of acid washed Bucky papers produced from each loading, ranged from 2.2 to 4.4 Ohm, with no direct correlation to PS loading. Due to this narrow range, the materials with different loading were mixed to create six wires of an Ethernet cable and tested using iPerf to give uplink and downlink speeds of ~99.5 Mbps, comparable to Cu wire of identical dimension (~99.5 Mbps). The lifecycle assessment (LCA) of CNT wire production was compared to copper wire production for the use case in a Boeing 747-400 over the lifespan of the craft. Due to their lightweight nature the CNT wires decreased the CO2 footprint by 21 kTonne (kTe) over the aircraft lifespan.

The growing production and application of carbon-based nanomaterials (CNMs) represent possible risks for aquatic systems. However, the variety of CNMs with different physical and chemical properties, and different morphology complicated the understanding of their potential toxicity. This paper aims to evaluate and compare the toxic impact of four most common CNMs, namely multiwalled carbon nanotubes (CNTs), fullerene (C60), graphene (Gr), and graphene oxide (GrO) in marine microalgae Porphyridium purpureum. The microalgae cells were exposed to the CNMs for 96 h and measured by flow cytometry. Based on the obtained results, we determined no observed effect level (NOEL), calculated EC10 and EC50 concentrations for growth rate inhibition, esterase activity, membrane potential, and reactive oxygen species (ROS) generation changes for each tested CNMs. According to the sensitivity (growth rate inhibition) of P. purpureum, the used CNMs can be listed in following order: CNTs > GrO > Gr > C60. The toxicity of CNTs was significantly higher than the toxic effect of the other used CNMs and only this sample caused increase of ROS generation in microalgae cells. This effect caused by trace metal residuals in CNTs and high affinity between particles and microalgae associated with the presence of exopolysaccharide coverage on P. purpureum cells.

The anode of a microbial fuel cell (MFC) was formed on a graphite electrode and immobilized Gluconobacter oxydans VKM-1280 bacterial cells. Immobilization was performed in chitosan, poly(vinyl alcohol) or N-vinylpyrrolidone-modified poly(vinyl alcohol). Ethanol was used as substrate. The anode was modified using multiwalled carbon nanotubes. The aim of the modification was to create a conductive network between cell lipid membranes, containing exposed PQQ-dependent alcoholdehydrogenases, and the electrode to facilitate electron transfer in the system. The bioelectrochemical characteristics of modified anodes at various cell/polymer ratios were assessed via current density, power density, polarization curves and impedance spectres. MFCs based on chitosan at a matrix/cell volume ratio of 5:1 produced maximal power characteristics of the system (8.3 μW/cm2) at a minimal resistance (1111 Ohm cm2). Modification of the anode by multiwalled carbon nanotubes led to a slight decrease of internal resistance (down to 1078 Ohm cm2) and to an increase of generated power density up to 10.6 μW/cm2. We explored the possibility of accumulating electric energy from an MFC on a 6,800-μF capacitor via a boost converter. Generated voltage was increased from 0.3 V up to 3.2 V. Accumulated energy was used to power a Clark-type biosensor and a bluetooth transmitter with three sensors, a miniature electric motor and a light-emitting diode.

In this work,the wave behaviour propagation of single-walled fluid conveying carbon nanotubes (SWCNT) under longitudinal magnetic fields and elastic foundations is studied, based on the nonlocal strain gradients theory(NSGT). With considertion of surface effect, the governing differential equation are obtained utilising Timoshenko beam theory and Hamilton's variational principle. The influence of small-scale parameters, fluid density, magnetic flux, surrounding elastic medium and surface effects on wave behaviour characteristics of carbon nanotubes are discussed in detail. The numerical results illustrated that with the magnetic flux increase，the phase velocities of the carbon nanotube will increase. When the fluid effects inside the carbon nanotube, the wave frequencies of the system reduces with increase in the non-local coefficient, while promotes with increase in the strain gradient coefficient. In addition, fluid density, surrounding elastic medium and surface effects have meaningful influence on the phase velocity of the system.

Pakistan being an agricultural country is raising 146.5 million commercial and domestic poultry birds which generate around 544,831 tons of waste. This waste finds its final disposal in agricultural land as soil fertilizer or disposal site amendment. The uncontrolled use of poultry litter for this purpose results in environmental impacts such as the emission of methane, a greenhouse gas. However, other options like thermochemical conversion of this waste can offer a better solution wherein poultry litter can be used as low-cost carbon sources for the synthesis of Carbon Nanotubes (CNTs). In this study, efforts have been made to utilize this cheap and plenty of available carbon source for synthesis of CNTs in the presence of Ni/Mo/MgO as a catalyst, through pyrolysis. The optimum mole ratio of catalyst (4:0.2:1) was found to yield more carbon product. Furthermore, process parameters such as temperature, time, polymer & catalyst weight were also optimized. The best possible process parameters that resulted (pyrolysis time (12 min), temperature (825◦C), and catalyst weight (100 mg) good yield of CNTs . The structure and morphology of produced nanotubes were confirmed through X-ray Diffractometer (X-RD) & Scanning Electron Microscopy (SEM). The environmental application of the nanotubes was tested in synthetic chromium solution in the lab using a batch experiment. Different experimental conditions (pH, adsorbent dosage and contact time) were optimized to enhance the adsorption of Cr (VI) by carbon nanotubes and UV-Visible spectrophotometer was used at 540nm to measure the absorbance of Cr (VI). Results show that up to 81.83% of Cr (VI) removal was achieved by using 8 mg of CNTs at pH 3 with 400 rpm at 180 min of contact time. Thus, it was concluded that poultry litter can be a useful source for the synthesis of CNTs and thereby removal of Cr (VI) from industrial tanneries wastewater.

We report a new fabrication method for a fully stretchable supercapacitor based on single wall carbon nanotube (SWCNT)-coated electrospun rubber nanofibers as stretchable supercapacitor electrodes. The deposition conditions of SWCNT on hydrophobic rubber nanofibers are experimentally optimized to induce a uniform coating of SWCNT. For surfactant-assisted coating of SWCNT, both water contact angle and sheet resistance were the lowest compared to the cases with other surface treatment methods, indicating the most effective coating approach. The excellent electromechanical properties of this electrode under the stretching condition is demonstrated by the measurement of Young’s modulus and normalized sheet resistance. This superb tolerance of the electrode with respect to stretching results from i) high aspect ratios of both nanofiber templates and the SWCNT conductors, ii) highly elastic nature of rubbery nanofiber, and iii) strong adherence of SWCNT-coated nanofiber on the elastic ecoflex substrate. Electrochemical and electromechanical measurements on the stretchable supercapacitor devices reveal that the volumetric capacitance (15.2 F cm-3 at 0.021 A cm-3) of the unstretched state is maintained for strains of up to 40 %. At this level of strain, the capacitance after 1,000 charge/discharge cycles is not significantly reduced. The high stability of our stretchable device suggests potential future applications in various types of wearable energy storage devices.

The stepwise hydrogenation of the C=C bond and C=O group of acrolein on Au₃ and Au₅ model systems is investigated using the density functional theory(DFT) PW91 functional. Our results show that the C=C hydrogenation is more favorable than that of C=O bond on Au₃ with the barriers of the rate-determining step being 0.35 and 0.62 eV respectively. On the other hand, the C=O reduction is preferred over the hydrogenation of the C=C bond on Au₅. The corresponding barriers of the rate-determining steps are 0.45 and 0.54 eV, respectively. This demonstrated that the second hydrogenation step controls the reaction on both Au₃ and Au₅ for C=O and C=C hydrogenation and the C=O hydrogenation on Au₅ is preferred over the hydrogenation of the C=C bond, which is helpful to address the reactivity of small size-selected supported gold clusters.

Confronting the dual challenges of rapid urbanization and climate change, although extensive research has investigated the influencing factors and practical strategies of urban carbon emissions and urban vibrancy, respectively, the unclear mutual nexus between them and the development strategy of collaborative optimization requires further in-depth analysis. This study explores the delicate balance between urban vibrancy and low-carbon sustainability within the confines of Beijing’s Fifth Ring Road. By integrating OpenStreetMap, land use, population, and building carbon emission data, we have developed a reproducible method to estimate total carbon emission and emission intensity per capita. Furthermore, we have introduced vibrancy index data to distinguish the vibrancy evaluation of residential and non-residential land and applied cross-combinational classification technology to dissect the spatial correlation between urban carbon emissions and urban vibrancy. The results reveal that the four combination typologies show more significant differences and regularity in residential land. Based on the discovery of spatial correlation, this study puts forward corresponding development strategy suggestions for each typology based on geographical location and the requirements of urban development policies of these four combination typologies. In conclusion, our study highlights the importance of integrating carbon emissions and urban vibrancy comprehensively in sustainable urban planning and proposes that various land use combinations need targeted development strategies to achieve this goal, which need to consider population, energy, service facilities, and other diverse aspects.

The design and fabrication of low-cost catalysts for highly efficient oxygen reduction is of paramount importance for various renewable energy-related technologies, such as fuel cells and metal-air batteries. Herein, we report the in situ growth of Fe3N nanoparticles encapsulated N-doped carbon nanotubes on the surface of flexible biomass-derived carbon cloth (Fe3N@CNTs/CC) via a simple one-step carbonization process. Taking advantage of its unique structure, Fe3N@CNTs/CC was employed as a self-standing electrocatalyst for oxygen reduction reaction (ORR) and possessed high activity as well as excellent long-term stability and methanol resistance in alkaline media. Remarkably, Fe3N@CNT/CC can directly play the role of both gas diffusion layer and electrocatalytic cathode in a zinc-air battery without additional means of catalyst loading, and display higher open circuit voltage, power density, and specific capacity in comparison with the commercial Pt/C catalyst. This work is anticipated to inspire the design of cost-effective, easy-preparation, and high-performance air electrodes for advanced electrochemical applications.

Oxygen evolution reaction (OER) is a key half-reaction in electrocatalytic water splitting. Large-scale water electrolysis is hampered by the commercial precious metal-based OER electrocatalysts owing to their high cost and slow kinetics. To address these issues, we present a facile one-pot room-temperature coprecipitation method to quickly synthesize carbon nanotubes-interconnected amorphous NiFe-layered double hydroxides (NiFe-LDH@CNT) as low-cost, efficient and stable OER electrocatalyst. NiFe-LDH@CNT hybrid catalyst delivers outstanding OER performance with a low onset overpotential of 255 mV and a small Tafel slope of 51.2 mV dec-1, as well as outstanding long-term stability. The terrific catalytic capability of NiFe-LDH@CNT can be associated with the synergistic effects of its room-temperature synthesized amorphous structure, bi-metallic modulation, and conductive CNT skeleton. The room-temperature synthesis can not only offer economic feasibility, but also obtain amorphous NiFe-LDH without crystalline boundaries, facilitating long-term stability during OER process. The bi-metallic nature of NiFe-LDH guarantees a modified electronic structure, providing additional catalytic sites. Simultaneously, the highly conductive CNT network fosters a nanoporous structure, facilitating electron transfer, O2 release and enriching catalytic sites. This study presents a strategy to purposefully design nanoarchitecture and facilely synthesize amorphous transition metal-based OER catalysts, ensuring the cost effectiveness, production efficiency, and long-term stability.

This research intended to report amine-functionalized multiwall carbon nanotubes (MWCNTs) prepared by a simple method for efficient and rapid removal of Reactive Yellow 2 (RY2) from water. EDS analysis showed that the N content increased from 0 to 2.42% and from 2.42 to 8.66% after modification by APTES and PEI, respectively. BET analysis displayed that the specific surface area, average pore size, and total pore volume were reduced from 405.22 to 176.16 m2/g, 39.67 to 6.30 nm, and 4.02 to 0.28 cm3/g, respectively. These results proved that the PEI/APTES-MWCNTs were successfully prepared. pH edge experiment indicated that pH 2 was optimal for RY2 removal. At pH 2 and 25 °C, the time required for adsorption equilibrium was 10, 15, and 180 min at initial concentrations of 50, 100, and 200 mg/L, respectively; and the maximum RY2 uptake calculated by the Langmuir model was 714.29 mg/g. Thermodynamic studies revealed that the adsorption process was spontaneous and endothermic. 0-0.1 mol/L of NaCl showed negligible effect on RY2 removal by PEI/APTES-MWCNTs. Five adsorption/desorption cycles confirmed the good reusability of PEI/APTES-MWCNTs in RY2 removal. Overall, the PEI/APTES-MWCNTs are a potential and efficient adsorbent for reactive dye wastewater treatment.

Recent developments in high-performance electrode materials have been pivotal for real-time monitoring biosensors, necessitating compatibility with biomaterials and robust electrochemi-cal properties. This study explores the development of electrode materials using single-walled carbon nanotubes (SWCNTs) and multi-walled carbon nanotubes (MWCNTs), with a primary fo-cus on assessing their dispersion and electrochemical properties. Various solvents, including N N-Dimethylformamide (DMF), deionized water, ethanol, and acetone, were used for dispersion analysis by employing ultrasonic waves. The results showed that SWCNTs exhibited well-dispersed characteristics without precipitation when introduced to a DMF solution. It found that resistance values decreased as the concentration of SWCNTs increased over the range of 0.025 to 0.4 g/L, with a considerable electrical conductivity reached at concentrations ranging from 0.2 g/L to 0.4 g/L in DMF. The biosensor platform was evaluated with 1-pyrenebutanoic acid succin-imidyl este (PBSE) as the linker and glucose oxidase (Gox) and chitosan as the binding substrate. The binding of Gox with glucose resulted in a significant decrease in resistance value of the biosensor with rising their concentrations ranged from 0.001 to 0.1 M. Though this research provides founda-tional insights for the advancement of SWCNT-based high-performance electrode materials, it will pave the way for the next generation of efficient and reliable biosensors.

The rapid urbanization in China has significantly contributed to the vast expansion of urban built-up areas. Precisely extracting and monitoring these areas is crucial for understanding and optimizing the developmental process and spatial attributes of smart, compact cities. However, most existing studies tend to focus narrowly on a single city or global scale with a single dimension, often ignoring mesoscale analysis across multiple urban agglomerations. In contrast, our study employs GIS and image processing techniques to integrate multi-source data for the identification of built-up areas. We specifically compare and analyze two representative urban agglomerations in China: the Yangtze River Delta (YRD) in the east and the Chengdu-Chongqing (CC) region in the west. We use different methods to extract built-up areas from socio-economic factors, natural surfaces, and traffic network dimensions. Additionally, we utilize a high-precision built-up area dataset of China as a reference for verification and comparison. Our findings reveal several significant insights: (1) The multi-source data fusion approach effectively enhances the extraction of built-up areas within urban agglomerations, achieving higher accuracy than previously employed methods. (2) Our research methodology performs particularly well in the CC urban agglomeration. The average precision rate in CC is 96.03%, while the average precision rate in YRD is lower at 80.33%. This study provides an objective and accurate assessment of distribution characteristics and internal spatial structure of built-up areas within urban agglomerations. This method offers a new perspective for identifying and monitoring built-up areas in Chinese urban agglomerations.

Soot combustion experiments with 5%O2/He were conducted using model soot, and four distinct compositions of CexPr1-xO2-δ oxides were prepared, varying nominal cerium com-positions (x=0, 0.2, 0.3, and 1). The catalyst samples were comprehensively characterized using techniques such as XRD, Raman spectroscopy, HR-TEM, N2 adsorption at −196 °C, XPS, O2-TPD, H2-TPR, and work function measurements. The Pr-rich compositions, rang-ing from Ce0.3Pr0.7O2-δ to PrO2-δ, resulted in a significant increase in the total evolved O2 amounts and enhanced catalyst reducibility. However, a decrease in textural properties of the catalysts was noted, being particularly important for the pure praseodymia under the synthesis route conducted. The catalytic activity was investigated under two contact modes of mixing between soot and catalyst: loose and tight. The results revealed that the catalytic performance is associated with the surface contact in tight contact mode and with the combination of surface/subsurface/bulk oxygen mobility and the BET surface ar-ea in loose contact mode. Notably, the T10 and T50 parameters were achieved at much lower temperatures than the uncatalyzed soot combustion, even under loose contact conditions. Specifically, the 50% conversion was achieved at 511℃ and 538℃ for Ce0.3Pr0.7O2 and Ce0.2Pr0.8O2, respectively. While no direct correlation between catalytic activity and work function was observed a significant relationship emerges between work function values and the formation of oxy-gen vacancies, whatever the conditions used for these measurements. On the other hand, the ability to generate a high population of oxygen vacancies at low temperatures, rather than the direct activation of gas-phase O2, influences the catalytic performance of Pr-doped ceria catalysts, highlighting the importance of surface/subsurface oxygen vacancy generation, which was the parameter which showed better correlation with the catalytic activity, whatever the soot conversion value or the mode of contact considered.

In this work, a ferrocene-containing gallic acid derivative modified carbon nanotubes paste electrode (Gal-Fc-CNT) obtained by simple mechanical mixing was studied for fast simultaneous voltammetric detection of doxorubicin (DOX), capecitabine (CPB) and cyclophosphamide (CPP) as cytostatic index by cumulative signal and selective detection of DOX. The electrochemical behaviors of individual and simultaneous DOX, CPB and CPP studied by cyclic voltammetry (CV) on Gal-Fc-CNT electrode at various pHs and potential ranges allowed the development of simple simultaneous detection method as cytostatic index at pH of 12 using square-wave voltammetry technique operated at modulation amplitude of 100 mV, step potential of 4 mV, frequency of 25 Hz and 100 mV·s−1 potential scan rate that allowed better performance than reported electrodes. Faster and selective detection of DOX with the lowest limit of detection of 75 ng⸱L-1 was achieved using square-wave voltammetry technique operated at modulation amplitude of 100 mV, step potential of 4 mV, frequency of 50 Hz and 200 mV·s−1 potential scan rate. The good results obtained for real tap water assessment indicated the utility of Gal-Fc-CNT paste electrode for practical applications (water samples, pharmaceutical formulations).

The availability of new self-sensing cement-based strain sensors allows the development of dense sensor networks for Structural Health Monitoring (SHM) of reinforced concrete structures. These sensors are fabricated by doping cement-matrix materials with conductive fillers, such as Multi Walled Carbon Nanotubes (MWCNTs), and can be embedded into structural elements made of reinforced concrete prior to casting. The strain sensing principle is based on the multifunctional composites outputting a measurable change in their electrical properties when subjected to a deformation. Previous work by the authors was devoted to material fabrication, modeling and applications in SHM. In this paper, we investigate the behavior of several sensors fabricated with and without aggregates and with different MWCNTs content. The strain sensitivity of the sensors, in terms of fractional change in electrical resistivity for unit strain, as well as their linearity are investigated through experimental testing under both static and dynamically varying compressive loadings. Moreover, the responses of the sensors when subjected to destructive compressive tests are evaluated. Overall, the presented results contribute to improving the scientific knowledge on the behavior of smart concrete sensors and to furthering their understanding for SHM applications.

Insulin-like Growth Factor 2 mRNA binding Protein 1 (IGF2BP1) is a promising candidate gene for influencing economic traits in livestock and poultry. The second intronic region of IGF2BP1 is closely related to growth traits, although the exact mechanism remains unclear. The preliminary resequencing results of goats in our laboratory demonstrated that the IGF2BP1 gene region was subject to strong selection, then we selected multiple single nucleotide polymorphisms (SNPs) to identify. Seven SNPs were located in the conserved region of the second intron, and their functions and relationship with growth traits require further clarification. This study selected 348 Nanjiang Yellow goats as experimental subjects, and chose Time of Flight Mass Spectrometer (MALDI-TOF) as the main method. Our results showed that six SNPs were significantly correlated with the growth traits of the Nanjiang yellow goat by association analysis. Among them, the rs652062749(A>G) was identified as the primary locus affecting the later stage of growth traits of Nanjiang yellow goat. Moreover, there was a strong linkage among three SNPs, and the rs638185407 (T>A) mutant type was observed to increase the luciferase activity in H293T cells extremely significantly. The TTAACT, TTCCCC, and ATCACT combination genotypes were dominant combination genotypes, which provided theoretical references for further genetic co-breeding. The results of our study demonstrate the potential role of the IGF2BP1 gene as a functional genetic marker in the breeding programs of Nanjiang Yellow goats.

Carbon offsetting is currently a major tool in managing carbon emissions and the drive to Net-Zero. This study aims to identify the offsetting potential of existing conservation schemes, and whether carbon offsetting credits could potentially finance the continued management of the conservation activities. The results from Dorset, in the UK indicate that many existing conservation schemes in woodland, heathland and grasslands can not only enhance biodiversity but also capture significant amounts of carbon. We show that the cost per additional tonne of carbon sequestered as a result of conservation activities varies considerably between different conservation projects. On average, the cost of this offsetting is £80 per tonne CO2e sequestered and ranging between £120 and £0 depending on the project and whether existing biodiversity grants would be available. However, this figure was based on adapting and refining existing conservation projects, and did not involve expensive factors such as purchase of land, which make the prices potentially unrealistic. While the costs identified are higher than many offsetting schemes at present, it could present a useful option for those wishing to localise their offsetting, and could be combined with biodiversity credits or other credit schemes to make the higher costs more attractive.

The multi-stage, multi-level assembly job shop scheduling problem (MsMlAJSP) is commonly encountered in the manufacturing of complex customized products. Ensuring production efficiency while effectively improving energy utilization is a key focus in the industry. For the energy-efficient MsMlAJSP (EEMsMlAJSP), an improved imperialist competitive algorithm based on Q-learning (IICA-QL) is proposed to minimize the maximum completion time and total energy consumption. In IICA-QL, a decoding strategy with energy-efficient triggers based on problem characteristics is designed to ensure solution quality while effectively enhancing search efficiency. Additionally, an assimilation operation with operator parameter self-adaptation based on Q-learning is devised to overcome the challenge of balancing exploration and exploitation with fixed parameters, thus the convergence and diversity of the algorithmic search is enhanced. Finally, the effectiveness of the energy-efficient strategy decoding trigger mechanism and the operator parameter self-adaptation operation based on Q-learning is demonstrated through experimental results, and the effectiveness of IICA-QL for solving EEMsMlAJSP is verified by comparing with other algorithms.

Bio-inspired gyroid triply periodic minimum surface (TPMS) lattice structures have been the focus of research in automotive engineering because they can absorb a lot of energy and have wider plateau ranges. The main challenge is determining the optimal energy absorption capacity and accurately capturing plastic plateau areas using finite element analysis (FEA). Using nTop's Boolean subtraction method, this study combined walled TPMS gyroid structures with normal TPMS gyroid lattice. This made a composite TPMS-gyroid lattice with relative densities ranging from 14% to 54%. Using the ideaMaker software and the fused deposition modeling (FDM) Raise3D Pro 2 3D printer to print polylactic acid (PLA) bioplastics in 1.75 mm filament made it possible to slice computer aided design (CAD) models and fabricate 36 lattices samples precisely layer by layer technique. Shimadzu 100kN testing equipment was utilized for the mechanical compression experiments. And the validation using finite element analysis (FEA). Further, CTG was examined using a field emission scanning electron microscope (FE-SEM) before and after compression testing. The composite TPMS gyroid lattice showed potential as shock absorbers for vehicles with relative densities of 33%, 38%, and 54%. The Gibson-Ashby model showed that the composite TPMS gyroid lattice deformed mainly by bending, and the size effect was seen when the relative densities were less than 15%. The lattice's relative density had a significant impact on its ability to absorb energy. The research also explored the use of these innovative foam-like composite TPMS-gyroid lattices in high-speed crash box scenarios, potentially enhancing vehicle safety and performance.

Commercially available paraffin wax LTP ST, manufactured in Poland by POLWAX, was used as a phase change material (PCM) for passive cooling of a LED panel containing 28 high power light emitting diodes (LEDs). Paraffin wax LTP ST of density = 930 kgm-3 at room temperature (RT) was chosen over other POLWAX waxes (LUXOLINA, LUXOLINA-ST, LTP 56-20) because of its melting point range (44.5 – 55.4)℃, relatively high latent heat of fusion H = 218.8 Jg-1, high specific heat Cp = 2.11 Jg-1K-1 and thermal conductivity k=0.233 Wm-1K-1 at 0 ℃ [1]. The thermophysical properties were studied in samples of pure LTP ST paraffin and doped with multi-walled carbon nanotubes (1.99, 3.49, 5.35, 10.49 wt%, MWCNT) or silver nanowires (0.26, 0.32, 1.06, 2.10, 7.35 wt%, SNW). Analysis of the thermal effects of doped samples showed a relative increase in the degree of subcooling, averaging 100% for MWCNT and 46% for SNW , a relative 15÷25% decrease in enthalpy of melting for MWCNT and 14÷16% for SNW. A 44% increase in thermal conductivity was found for the sample containing 5.35 wt% MWCNTs and a 91% increase for 1.06 wt% SNW. The results of cooling efficiency tests for 3 types of developed heat sinks made of AW-2017A aluminum alloy are presented, i.e.: (a) - full system without PCM filling, (b) - system with PCM chamber without intracellular ribs, (c) system with PCM chamber with intracellular fins.

Buckling defect will appear on the outer surface of the deformed ring during constrained ring rolling (CRR) of aluminum alloy thin wall conical ring with inner high ribs (AATWCRIHR), if the geometrical dimension of the ribs doesn't match the wall thickness. To avoid the buckling defect, a quantitative method for characterizing the degree of the buckling defect is proposed using the area of buckling profile. Then an orthogonal experimental scheme was designed taking the width of the middle rib, thickness of wall, and height of the middle rib as design variables and defining the area of buckling profile as optimization objective. Subsequently, a quadratic polynomial response surface model was established by combining the optimization algorithm with the finite element method (FEM), and the geometrical dimension of the middle ribs of the deformed AATWCRIHR is optimized. Also the optimal parameter combination to minimize the area of buckling profile is obtained and verified using FE simulation. Results show that the AATWCRIHR after optimization doesn’t generate the buckling defect during constrained ring rolling, and it is proved that the quantitative buckling defect representation method and the optimization design method based on the response surface model and the finite element simulation results are feasible for the constrained ring rolling process of the AATWCRIHR.

This paper, from the perspective of Mode 3 of knowledge production, takes the important carrier of knowledge, scientific research papers, as the research object. The mainstream databases (SCIE and SSCI) are chosen as the data sources. Firstly, bibliometric methods are applied to analyze the cooperation status among the main bodies of paper production, including authors and their affiliated institutions, countries, and disciplines; secondly, the Analytic Hierarchy Process (AHP) is used to construct a comprehensive evaluation model for the state of research cooperation in carbon neutrality. Based on the evaluation model, the cooperation characteristics of different disciplinary fields and the relationship between paper cooperation status and high-impact research papers are comparatively analyzed. At the same time, an analysis is conducted on the support from the government, the sponsorship from enterprises, and the participation of the public in the process of paper production. Finally, some suggestions are put forward on how to build an innovative ecosystem for carbon neutrality research from the perspective of Mode 3 of knowledge production.

High-performance poly(1,4-butylene terephthalate (PBT) nanocomposites have been developed via the consideration of phosphorus-containing agents and amino-carbon nanotube (A-CNT). One-pot functionalization method has been adopted to prepare functionalized CNTs via the reaction between A-CNT and different oxidation state phosphorus-containing agents, including chlorodiphenylphosphine (DPP-Cl), diphenylphosphinic chloride (DPP(O)-Cl), and diphenyl phosphoryl chloride (DPP(O3)-Cl). These functionalized CNTs, DPP(Ox)-A-CNTs (x = 0, 1, 3), were respectively mixed with PBT to obtain the CNTs-based polymer nanocomposites through a melt blending method. SEM observations demonstrated that DPP(Ox)-A-CNT nano-additives were homogeneously distributed within PBT matrix compared to A-CNT. The incorporation of DPP(Ox)-A-CNT improved the thermal stability of PBT. Moreover, PBT/DPP(O3)-A-CNT showed the highest crystallization temperature and tensile strength, due to the superior dispersion and interfacial interactions between DPP(O3)-A-CNT and PBT. PBT/DPP(O)-A-CNT exhibited the best flame retardancy resulting from the excellent carbonization effect. The radicals generated from decomposed polymer were effectively trapped by DPP(O)-A-CNT, leading to the reduction of heat release rate, smoke production rate, carbon dioxide and carbon monoxide release during cone calorimeter tests.

As the world’s second largest economy, China ranks amount the world’s top nations when it comes to carbon emission, and therefore its attitude towards climate change is closely followed by all parties concerned. There have been few researches on the role of environmental governance in low-carbon city transformation process, especially the Chinese one. This paper analyses the role of government environmental regulation played in the low-carbon city transformation process by taking Shenzhen as the research object. One of the world's youngest super cities, it also happens to be the lowest carbon emission intensity city in China. Striving to explore green low-carbon development path for the whole country, Shenzhen provides practical experience for countries to cope with global climate change. However, its efforts to reduce the total carbon emissions failed, but it emphasized the carbon emission intensity, which is consistent with the international commitments made by the central government. China’s policy towards handling climate change relies on hierarchical governance arrangement. The strength of the NGOs in the country is weak and incomparable with the government’s, which has mastered most of the resources and is just a reality in China.

Snap-fit is a commonly used jointing/connention mechanism, and its easy installation and difficult removal are the result of the coordinated interaction between friction, geometric shape, and elasticity. This paper presents a detailed study on the assembly/disassembly forces of thin-walled torus snap-fit through finite element simulation, experimental testing, and data fitting of approximate analytical solutions. The research reveals that the non-zero Gaussian curvature of the torus has a significant impact on the mechanical performance of the torus snap fit. The findings in this study are of great significance for future design of high-performance structural connections.

Preventing or treating infections at implantation sites where the risk of bacterial contamination is high requires the development of intelligent drug delivery systems. In this work, honeycomb structures as a potential drug carrier were obtained for the first time in a fast, one-step anodization process of titanium grade 4, lasting only 60 seconds. Fourth generation oxide nanotube layers were obtained from an aqueous solution of 0.5% AgNO3 in the voltage range from 50 to 80 at 15(1) °C. The FE-SEM method showed the length of the oxide nanotubes from 1.02(2) µm at 50 V to 230(8) nm at 80 V. The EDS analysis revealed that during anodizing, silver particles are deposited on the Ti G4 up to 2.2(5) wt.%. Electrochemical measurements by open circuit potential and anodic polarization curves methods proved the improvement of in vitro corrosion resistance as a result of Ti G4 anodizing. Assessment of the anodized Ti G4 as gentamicin sulfate carrier carried out using ATR-FTIR and UV-VIS absorption spectroscopy revealed that the obtained oxide nanotube layers can be used for application of drugs directly to the tissue around the implant. This method of application allows full use of the therapeutic dose of the antibiotic used.

Mechanical robustness and high energy efficiency of composite materials are immensely important in modern stretchable, self-powered electronic devices. However, the availability of these materials and their toxicities are challenging factors. This paper presents the mechanical and energy-harvesting performances of low-cost natural rubber composites made of stearic acid-modified diatomaceous earth (mDE) and carbon nanotubes (CNTs). The obtained mechanical properties were significantly better than those of unfilled rubber. Compared to pristine diatomaceous earth, mDE has higher reinforcing efficiencies in terms of mechanical properties because of the effective chemical surface modification by stearic acid and enhanced filler-rubber interactions. The addition of a small amount of CNT as a component in the hybrid filler systems not only improves the mechanical properties but also improves the electrical properties of the rubber composites and has electromechanical sensitivity. For example, the fracture toughness of unfilled rubber (9.74 MJ/m3) can be enhanced by approximately 484% in a composite (56.86 MJ/m3) with 40 phr (per hundred grams of rubber) hybrid filler, whereas the composite showed electrical conductivity. At a similar mechanical load, the energy-harvesting efficiency of the composite containing 57 phr mDE and 3 phr CNT hybrid filler was nearly double that of the only 3 phr CNT-containing composite. The higher energy-harvesting efficiency of the mDE-filled conductive composites may be due to their increased dielectric behaviour. Because of their bio-based materials, rubber composites made by mDE can be considered eco-friendly composites for mechanical and energy harvesting applications and suitable electronic health monitoring devices.

Nanoparticles of graphene and carbon nanotubes are attractive materials for improvement of mechanical and barrier properties and functionality of biodegradable polymers for food packaging applications. However, the increase of the manufacture and consumption increases the probability of exposure of human and environment to such nanomaterials, this rising questions about the risks of nanomaterials since they can be toxic. For a risk assessment, it is crucial to know whether airborne nanoparticles of graphene and carbon nanotubes can be released from nanocomposites into the environment at their end-life, or they remain embedded in the matrix. In this work the release of graphene and carbon nanotubes from the poly(lactic) acid nanocomposite films were studied for the scenarios of: (i) biodegradation of matrix polymer at the disposal of wastes; and (ii) combustion and fire of nanocomposite wastes. Thermogravimetric analysis in air atmosphere, TEM, AFM and SEM were used to verify the release of nanoparticles from nanocomposite films. The three factors model was applied for the quantitative and qualitative risk assessment to the release of graphene and carbon nanotubes from nanocomposite wastes for these scenarios. Safety concern is discussed in respect to the existing regulations for nanowastes stream.

Corrugated board, widely used in the packing industry, is a recyclable and durable material. Its strength and cushioning, influenced by geometry, environmental conditions like humidity and temperature, and paper quality, make it versatile. Double-walled (or five-ply) corrugated board, comprising two flutes and three liners, enhances these properties. This study introduces a novel approach to analyze 5-layered corrugated board, extending a previously published algorithm for single-walled boards. Our method focuses on measuring layer and overall board thickness, flute height, and center lines of each layer. Integrating image processing and genetic algorithms, the research successfully developed an algorithm for precise geometric feature identification of double-walled boards. Images were recorded using a special device with a sophisticated camera and image sensor for detailed corrugated board cross-sections. Demonstrating high accuracy, the method faced limitations only with very deformed or damaged samples. This research contributes significantly to quality control in the packaging industry and paves the way for further automated material analysis using advanced machine learning and image sensors. It emphasizes the importance of sample quality and suggests areas for algorithm refinement to enhance robustness and accuracy.

Corrugated cardboard is an ecological material, mainly because, in addition to virgin cellulose fibers also the fibers recovered during recycling process are used in its production. However, the use of recycled fibers causes slight deterioration of the mechanical properties of the corrugated board. In addition, converting processes such as printing, die-cutting, lamination, etc. cause micro-damage in the corrugated cardboard layers. In this work, the focus is precisely on the crushing of corrugated cardboard. A series of laboratory experiments were conducted, in which the different types of single-walled corrugated cardboards were pressed in a fully controlled manner to check the impact of the crush on the basic material parameters. The amount of crushing (with a precision of 10 micrometers) was controlled by a precise FEMat device, for crushing the corrugated board in the range from 10 to 70 % of its original thickness. In this study, the influence of crushing on bending, twisting and shear stiffness as well as a residual thickness and edge crush resistance of corrugated board was investigated. Then, a procedure based on a numerical homogenization, taking into account a partial delamination in the corrugated layers to determine the degraded material stiffness was proposed. Finally, using the empirical-numerical method, a simplified calculation model of corrugated cardboard was derived, which satisfactorily reflects the experimental results.

Laser Photoacoustic Spectrometers (LPAS), which provide photoacoustic spectra for detecting food frauds or adulteration, and fluorescence-based systems for recognition of contamination by heavy metal ions in water are two important families of sensors for health and environmental purposes. Both sensor families require one or more low-frequency Lock-In Amplifiers (LIAs) to extract the signal of interest from background noise. In the cited applications, the required LIA frequency is quite low (up to 1kHz), and this leads to a simplification of the hardware with consequent good results in portability, economy, reduced size, weight and low-cost characteristics. The present system, called ENEA DSP Box Due, is based on a very inexpensive microcontroller proto-board and can replace four commercial LIAs, resulting in significant savings in both cost and space. Furthermore, it incorporates a dual-channel oscilloscope and a sinusoidal function generator. This article outlines the architecture of the ENEA DSP Box Due, its electrical characterization and its applications within a project concerning laser techniques for food and water safety.

As the largest contributor of carbon emissions in China, the building sector currently relies mostly on enterprises’ own effort to report carbon emissions, which usually results in challenges related to information transparency and workload for regulatory bodies, who play an otherwise vital role in controlling the building sector’s carbon footprint. In this study, we established a novel regulatory model known as QCEPM (Quantitative Carbon Emission Prediction Model) by conducting multiple linear regression analysis using the quantities of concrete, rebar, and masonry structures as independent variables, and the embodied carbon emissions of a building as the dependent variable. We processed the data in the detailed quantity list of 20 multi-story frame-structure buildings and fed them to QCEPM for solution. Comparison of the QCEPM-calculated results against the time-consuming and error-prone manual calculation results suggested a mean absolute percentage error (MAPE) of 2.26%. Using this simplified model, regulatory bodies can efficiently supervise the embodied carbon emissions in multi-storey frame structures by setting up carbon quota for a project in its approval stage, allowing the construction enterprise to carry out dynamic control over the audited three most important building materials throughout a project’s planning and implementation phase.

Carbon dioxide (CO2)miscible fracturing huff and puff technology plays a pivotal role in enhancing the recovery rate of crude oil, particularly in reservoirs with challenging physical properties, strong water sensitivity, high injection pressure, and complex water injection dynamics. In this study, the oil-increasing mechanism and huff and puff effect of CO2 miscible fracturing fluid are investigated through a comprehensive experimental approach. Specifically, experiments on PVT gas injection expansion, minimum miscible pressure, and CO2 miscible fracturing huff and puff are conducted on the G fault block reservoir in J Oilfield. The findings demonstrate that injecting CO2 into reservoirs leads to oil volume expansion, viscosity reduction, and saturation pressure increase. Additionally, the inclusion of solubilizers and viscosity reducers further enhances the efficiency of crude oil extraction. Solubilizers not only improve oil recovery but also reduce the minimum miscible pressure required for effective CO2 dispersion. Furthermore, the shut-in time, permeability, and huff and puff method all have considerable impacts on huff and puff recovery rate. This study offers valuable technical insights, supporting the application of CO2 miscible fracturing huff and puff technology to enhance oil recovery in low-permeability reservoirs.

Two-dimensional arrays of hollow nanotubes made of TiO2 are a promising platform for sensing, spectroscopy and light harvesting applications. Their straightforward fabrication via electrochemical anodization, growing nanotube pillars of finite length from a Ti foil, allows precise tailoring of geometry and, thus, material properties. We investigate these photonic crystal structures with respect to reduction of front surface reflection, achievable field enhancement, and photonic bands. With the Rigorous Coupled Wave Analysis (RCWA), we study the optical response of photonic crystals made of thin-walled nanotubes relative to the bare Ti foil substrate, including under additional charge carrier doping.

This paper considers a new approach to the modeling of the vacuum infusion process at the manufacturing three-dimensional composite parts of complex shape. The developed approach and numerical methods are focused on the reliable prediction with the needed accuracy and elimination the unrecoverable defect of composite structure such as the dry spots. The paper presents some experimental results, which demonstrate two cases of dry spots formation in large aircraft composite panels, and analyses the reasons of these defects arising. Our numerical technique is based on the vacuum infusion of the liquid resin into porous preform as the two phase flow, which is described by the phase field equation coupled with the Richards equation describing the fluid motion in unsaturated soils with spatially varied pressure dependant porosity and saturation. This problem statement allowed to correctly reconstruct the resin front motion and formation of inner and outer dry spots depending on its movement. For the rapid detection of preform zones that are suspicious for defect formation two indicators calculated during process simulation are proposed and tested at the numerical experiments. The auxiliary program tool has been developed in MATLAB environment to correctly detect the times of formation, localization and dimensions of the arising dry spots by using the results of the finite element model simulation.