Solar and wind resources available for power generation are subject to variability due to meteorological factors. Here, we use a new global climate reanalysis product, Version 2 of the NASA Modern-Era Retrospective Analysis for Research and Applications (MERRA-2), to quantify interannual variability of monthly-mean solar and wind resource from 1980 to 2016 at a resolution of about 0.5 degrees. We find an average coefficient of variation (CV) of 11% for monthly-mean solar radiation and 8% for windspeed. Mean CVs were about 25% greater over ocean than over land, and, for land areas, were greatest at high latitude. The correlation between solar and wind anomalies was near zero in the global mean, but markedly positive or negative in some regions. Both wind and solar variability were correlated with values of climate modes such as the Southern Oscillation Index and Arctic Oscillation, with correlations in the Northern Hemisphere generally stronger during winter. We conclude that reanalysis solar and wind fields could be helpful in assessing variability in power generation due to interannual fluctuations in the wind and solar resource. Skillful prediction of these fluctuations seems to be possible, particularly for certain regions and seasons, given persistence or predictability of climate modes with which these fluctuations are associated.

The up-to-date challenge towards clean road transport are non-exhaust emissions. Important advances regarding measurement systems, including well defined characterisation techniques, as well as regulation, will happen in the next few years. In this work we present detailed results of particle emissions from a test bed for wheel suspension and brakes, consisting of aerosol (size distribution, particle number (PN) and mass (PM)) and electron microscopy measurements (EM) under different load conditions. Standard tyres and brakes from series production were tested with a high-load driving cycle while particle measurements were conducted by gravimetric measurements and with a TSI SMPS, a TSI APS and a GRIMM OPS. Furthermore, samples were analyzed by electron microscopy. A bimodal particle size distribution (PSD) was obtained with the SMPS, with peaks at 20nm and around 400nm. EM analysis of >1400 single particles from the electrostatic sampler matches the PSD results. EM analysis also showed ultrafine particles, mainly from O, Fe, Si, Ba, Mg and S and also fractal particles with high C fractions. Our results suggest, in agreement with previously published literature, that particulate emissions are related to brake disc temperature and occur in significant amounts above a threshold temperature.

This paper presents a piezoresistive pressure sensor with a shield layer for improved stability. Compared with the conventional piezoresistive pressure sensors, p-type piezoresistors are covered by an n-type shield layer, which is formed by ion implantation. The proposed pressure sensors have been successfully fabricated by bulk micromachining techniques. The impact of electrical field on piezoresistors is studied by simulation. The temperature drift of the pressure sensor has been investigated by both simulation and experimental measurement. Characteristics of developed pressure sensors are tested from -40 C to 125 C. A sensitivity of 0.022 mV/V/KPa and a maximum non-linearity of 0.085% FS are measured for the fabricated sensor in a pressure range of 1 MPa. The temperature coefficients of resistance of shielded piezoresistors are found to be smaller than those of un-shielded ones. It is demonstrated that the shield layer is able to reduce the drift caused by electrical field and ambient temperature variation.

Wearable technology has been proposed as a potential tool to change the way of human life, such as the smart bracelet and the Google Glass. In the wearable technology, the inertial sensor has great significance in tracking the object movements. The paper focused on detecting the movements of user’s finger based on the inertial sensor to give the control signals. Firstly, the attitude matrix, which represented the transformation relation of carrier coordinate system and the navigation coordinate system, was obtained. Secondly, the attitude matrix was expressed based on the quaternions. Thirdly, the finger gesture was processed by the attitude matrix to get the attitude angle. Finally, the robot was controlled by attitude angle to make the moving action. The experimental results showed the detection of the finger movement is effective.

Global change is affecting vegetation cover and processes through multiple pathways. Long time series of surface land surface properties derived from satellite remote sensing offer a unique abilities to observe these changes, particularly in areas with complex topography and limited research infrastructure. Here, we focus on Nepal, a biodiversity hotspot where vegetation productivity is limited by moisture availability (dominated by a summer monsoon) at lower elevations and by temperature at high elevations. We analyze normalized difference vegetation index (NDVI) from 1981 to 2015 semimonthly, at 8 km spatial resolution. We use a random forest (RF) of regression trees to generate a statistical model of NDVI as a function of elevation, land use, CO2 level, temperature, and precipitation. We find that NDVI has increased over the studied period, particularly at low and middle elevations and during fall (post-monsoon). We infer from the fitted RF model that the NDVI linear trend is primarily due to CO2 level (or another environmental parameter that is changing quasi-linearly), and not primarily to temperature or precipitation trends. On the other hand, interannual fluctuation in NDVI is more correlated with temperature and precipitation. RF accurately fits the available data and shows promise for estimating trends and testing hypotheses about their causes.

A portable laser photoacoustic sensor based on a Field-Programmable Gate Array (FPGA) is reported for methane detection. A tunable DFB diode laser in the 1654 nm wavelength range is used as an excitation source. The photoacoustic signal processing was implemented by a FPGA device. A small resonant photoacoustic cell is designed. The minimum detection limit (1σ) of 10 ppm for methane (CH₄) is demonstrated.

Re-shaping of thermodynamics with the graph theory and Ramsey theory is suggested. Maps built of thermodynamic states are addressed. Thermodynamic states may be attainable and non-attainable by the thermodynamic process in the system of constant mass. We address the following question how large should be a graph describing connections between discrete thermodynamic states to guarantee the appearance of thermodynamic cycles? The Ramsey theory supplies the answer to this question. Direct graphs emerging from the chains of irreversible thermodynamic processes are considered. In any complete directed graph, representing the thermodynamic states of the system the Hamiltonian path is found. Transitive thermodynamic tournaments are addressed. The entire transitive thermodynamic tournament built of irreversible processes does not contain a cycle of length 3, or in other words, the transitive thermodynamic tournament is acyclic and contains no directed thermodynamic cycles.

This study involved a comprehensive examination of sensory attributes in Bísaro dry-cured loins, including odor, androsterone, scatol, color, fat color, hardness, juiciness, chewiness, flavor intensity, and flavor persistence. Analysis of 40 samples revealed a wide variation in these attributes, ensuring a robust margin for multivariate calibration purposes. The respective near-infrared (NIR) spectra unveil distinct peaks associated with significant components such as protein, lipid, and water. Support Vector Regression (SVR) models were methodically calibrated for all sensory attributes, with optimal results using multiplicative scattering correction pre-treatment, MinMax normalization, and radial base kernel (non-linear SVR model). The predictive models exhibited acceptable results, characterized by R-squared values close to 1 (0.9616 - 0.9955) and low RMSE values (0.0400 – 0.1031). The prediction set's relative standard deviation (RSD) remained under 5%. Comparisons with prior research revealed significant improvements in prediction accuracy, particularly when considering attributes like pig aroma, hardness, fat color, and flavor intensity. This research underscores the potential of advanced analytical techniques to improve the precision of sensory evaluations in food quality assessment.

We apply the Ramsey theory to the analysis of geometrical properties of closed contours. Consider a set of six points placed on a closed contour. The straight lines connecting these points are yikx=αikx+βik i,k=1...6, αik≠0. We color the edges connecting the points for which αik>0 holds with red, and the edges for which αik<0 with green with red. At least one monochromic triangle should necessarily appear within the curve (according to the Ramsey number R3,3=6). This result is immediately applicable for the analysis of dynamical billiards. The second theorem emerges from the combination of the Jordan curve and Ramsey theorem. The closed curve is considered. We connect the points located within the same region with green links and the points placed within the different regions with red links. In this case, transitivity/intransitivity of the relations between the points should be considered. Ramsey constructions arising from the differential geometry of closed contours are discussed.

Declaration of smallpox eradication by the WHO on 1980 led to discontinuation of the world-wide vaccination campaign. The increasing percentage of unvaccinated individuals, the existence of its causative infectious agent variola virus (VARV) and the recent synthetic achievements, increases the threat of intentional or accidental release and reemergence of smallpox. Control of smallpox would require an emergency vaccination campaign as no other protective measure has been approved to achieve eradication and ensure world-wide protection. Experimental data in surrogate animal models support the assumption, based on anecdotal, uncontrolled historical data, that vaccination up to 4 days postexposure, confers effective protection. The long incubation period and the uncertainty of the exposure status in the surrounding population calls for the development and evaluation of safe and effective methods that would allow to extend the therapeutic window and to reduce the disease manifestations and vaccine adverse reactions. To achieve these goals, we need to evaluate the efficacy of novel and already licensed vaccines as a sole treatment or in conjunction with immune modulators and antiviral drugs. In this review, we address the available data, recent achievements and open questions.

In this project, four of fibers Bragg gratings were fabricated by injecting different volumes of liquids (star line Glass Mechanix optical adhesive material, olive oil diluted with ethanol) into the hollow core fiber. The amplitude splitting interferometric technique with a high resolution specially designed translation stage was used for the fabrication process. The fabrication was done using ultraviolet laser operated at wavelength 405nm. The fabricated Bragg length of the four fibers is equal to 3.8 cm. The results presented fiber Bragg grating (FBG) with successful fabrication at 653.3 nm Bragg reflected wavelength.

Parasitic diseases are among the most serious public health problems in developing countries, causing high mortality and economic burdens. The Trypanosomatidae family includes Leishmania spp. and Trypanosoma cruzi, which cause leishmaniasis and Chagas disease, respectively. Both these parasites are among the major agents of neglected tropical diseases (NTDs). Leishmaniasis is currently the second most widespread vector-borne parasitic disease after malaria. The World Health Organization (WHO) records approximately 0.7-1 million newly diagnosed leishmaniasis cases each year, resulting in approximately 20,000-30,000 deaths. Also, 25 million people worldwide are at risk of Chagas disease and an estimated 6 million people are infected with Trypanosoma cruzi. Despite the similarity of the parasites, the evolution of the disease and the clinical indexes are explicitly different in African, Asian, and American forms of infection. Clinical therapies are associated with drug resistance and side effects. As a result, the discovery of novel therapeutic agents has emerged as a top priority and a promising alternative. Peptide-based drugs are an attractive class of therapeutic agents. They are recognized for being highly selective and effective, as well as safe and well tolerated. Moreover, they are now being explored in the development of novel therapeutics for a variety of health disorders, including oncology, endocrinology, metabolic, cardiovascular, and bone diseases. In addition, they are being explored in tropical diseases such as leishmaniasis and Chagas disease. We will discuss current knowledge regarding the parasite life cycle, signs and symptoms, diagnosis, and treatment options for leishmaniasis and Chagas disease.

Ramsey theory influences the dynamics of mechanical systems, which may be described as abstract complete graphs. We address a mechanical system which is completely interconnected with the two kinds of ideal Hookean springs. The suggested system mechanically corresponds to the cyclic molecules, in which functional groups are interconnected with two kinds of chemical bonds, represented mechanically with two springs k1 and k2. In this paper, we consider a Cyclic system (molecule) built of six equal masses m and two kinds of springs. We pose the following question: what is the minimal number of masses in the such a system in which three masses are constrained to be connected with spring k1 or three masses to be connected with spring k2? The answer to this question is supplied by the Ramsey theory, and it is formally stated as follows: what is the minimal number R3,3? The result emerging from the Ramsey theory is R3,3=6. Thus, in the aforementioned interconnected mechanical system will be necessarily present the triangles (at least one triangle), built of masses and springs. This prediction constitutes the vibrational spectrum of the system. Thus, the Ramsey Theory supplies the selection rules for the vibrational spectra of the cyclic molecules. Symmetrical system built of six vibrating entities is addressed. The Ramsey approach works for 2D and 3D molecules, which may be described as abstract complete graphs. The extension of the proposed Ramsey approach to the systems, partially connected by ideal springs, viscoelastic systems and systems, in which elasticity is of an entropy nature is discussed. “Multi-color systems” built of three kinds of ideal springs are addressed. The notion of the inverse Ramsey network is introduced and analyzed.

This paper investigates an Energy Neutral System using Micro Energy Harvesters for a Health Monitoring Wireless Sensor Node (HM-WSN). We have implemented HM-WSN consisting of a solar cell energy harvester, a Power Management Unit (PMU) and the ucontroller, sensor and transmitter acting as load. A battery extender and a switching logic circuit for sensor node is designed to evaluate the efficiency of the proposed system. The HM-WSN senses body temperature with improvement in lifetime of coincell. The HM-WSN is built using commercially available off the shelf (COTS components and consumes 47.2uW for data being updated every 134s. It can be operated for approximately 1.32 years only on a coincell. Furthermore, the HM-WSN can be operated with solar energy at 200lux, achieving 96.36 years with a combination of a coincell with an additional capacitor of 2.2mF. It attains 4.07 years to 16.87 years lifetime with the load capacitor varying from 1mF to 1.5mF at 350lux lighting condition. With the same ambient condition and a 2mF load capacitor, HM-WSN attains complete energy autonomy.

With the integrated development of the Internet, wireless sensor technology, cloud computing, and mobile Internet, there has been a lot of attention given to research about and applications of the Internet of Things. A Wireless Sensor Network (WSN) is one of the important information technologies in the Internet of Things; it integrates multi-technology to detect and gather information in a network environment by mutual cooperation, using a variety of methods to process and analyze data, implement awareness, and perform tests. This paper mainly researches the localization algorithm of sensor nodes in a wireless sensor network. Firstly, a multi-granularity region partition is proposed to divide the location region. In the range-based method, the RSSI (Received Signal Strength indicator, RSSI) is used to estimate distance. The optimal RSSI value is computed by the Gaussian fitting method. Furthermore, a Voronoi diagram is characterized by the use of dividing region. Rach anchor node is regarded as the center of each region; the whole position region is divided into several regions and the sub-region of neighboring nodes is combined into triangles while the unknown node is locked in the ultimate area. Secondly, the multi-granularity regional division and Lagrange multiplier method are used to calculate the final coordinates. Because nodes are influenced by many factors in the practical application, two kinds of positioning methods are designed: the unknown node is in the positioning unit or not. When the unknown node is on the side of the positioning unit, we use the method of vector similarity. Moreover, we use the centroid algorithm to calculate the ultimate coordinates of unknown node. When the unknown node is not on the side of the positioning unit, we establish a Lagrange equation containing the constraint condition to calculate the first coordinates. Furthermore, we use the Taylor expansion formula to correct the coordinates of the unknown node. In addition, this localization method has been validated by establishing the real environment.

Informational (Shannon) measures of symmetry are introduced and analyzed for the patterns built of 1D and 2D shapes. The informational measure of symmetry Hsym (G) characterizes the an averaged uncertainty in the presence of symmetry elements from the group G in a given pattern; whereas the Shannon-like measure of symmetry Ωsym (G) quantifies averaged uncertainty of appearance of shapes possessing in total n elements of symmetry belonging to group G in a given pattern. Hsym(G1)=Ωsym(G1)=0 for the patterns built of irregular, non-symmetric shapes. Both of informational measures of symmetry are intensive parameters of the pattern and do not depend on the number of shapes, their size and area of the pattern. They are also insensitive to the long-range order inherent for the pattern. Informational measures of symmetry of fractal patterns are addressed. The mixed patterns including curves and shapes are considered. Time evolution of the Shannon measures of symmetry is treated. The close-packed and dispersed 2D patterns are analyzed.

The existence of low-cost and accurate tools that can equip the First Responders (FRs) to detect trapped victims and provide insights about their health condition in the aftermath of a disaster, is imperative. To address the problem of detecting trapped victims behind walls or debris, we have developed a tool that exploits an Ultra-Wide Band (UWB) radar sensor for data collection and Machine Learning (ML) algorithms for data analysis. To evaluate the efficacy of our approach, we collected data from nine humans, both in standing and lying down positions. Next, we applied various ML algorithms to the collected dataset for two discrete sub-tasks that are of interest from an FR’s perspective. The first task is the detection of the victim’s presence, where the algorithms attained more than 95% accuracy and F1-Score. The second task is the estimation of the distance between the radar sensor and the victim, where the tool showed an average error of less than 40 cm.

Underwater Sensor Networks (UWSNs) can enable a broad range of applications such as resource monitoring, disaster prevention, and navigation-assisted. It is especially relevant for sensor nodes location in UWSNs. Global Positioning System (GPS) is not suitable for using in UWSNs because of the underwater propagation problems. Hence some localization algorithms based on the precise time synchronization between sensor nodes have been proposed which are not feasible for UWSNs. In this paper, we propose a localization algorithm called Two-Phase Time Synchronization-Free Localization Algorithm (TP-TSFLA). TP-TSFLA contains two phases, namely, range-based estimation phase and range-free evaluation phase. In the first phase, we address a time synchronization-free localization scheme base on the Particle Swarm Optimization (PSO) algorithm to decrease the localization error. In the second phase, we propose a Circle-based Range-Free Localization Algorithm (CRFLA) to locate the unlocalized sensor nodes which cannot obtain the location information through the first phase. In the second phase, sensor nodes which are localized in the first phase act as the new anchor nodes to help realize localization. Hence in this algorithm, we use a small number of mobile beacons to help achieve location without any other anchor nodes. Besides, to improve the precision of the range-free method, an extension of CRFLA by designing a coordinate adjustment scheme is updated. The simulation results show that TP-TSFLA can achieve a relative high localization ratio without time synchronization.

In this paper, a method is developed for presenting a novel virtual torque sensor based on precise model and position measurements avoids the need of traditional strain gauges and amplifiers. More specifically, the harmonic drive compliance model and the Gaussian process regression (GPR) technique are used together to achieve virtual torque sensor measurement. While the harmonic drive compliance model provides the analytic part, the Gaussian process regression method is used to reconstruct the unmolded part based on motor-side and link-side joint angles as well as motor current. After an automatic offline calibration, the method allows for a lean online implementation. The virtual torque sensor measurement is compared with measurements of a commercial torque sensor, and the results have attested the effectiveness of the proposed method.

We used the complete set of convex pentagons enabling filing the plane without any overlaps or gaps (including the Marjorie Rice tiles) as generators of Voronoi tessellations. Shannon entropy of the tessellations was calculated. Some of the basic mosaics are flexible and give rise to a diversity of Voronoi tessellations. The Shannon entropy of these tessellations varied in a broad range. Voronoi tessellation, emerging from the basic pentagonal tiling built from hexagons only, was revealed (the Shannon entropy of this tiling is zero). Decagons and hendecagon did not appear in the studied Voronoi diagrams. The most abundant Voronoi tessellations are built from three different kinds of polygons. The most widespread is the combination of pentagons, hexagons and heptagons. The most abundant polygons are pentagons and hexagons. No Voronoi tiling built only of pentagons was registered. Flexible basic pentagonal mosaics give rise to a diversity of Voronoi tessellations, which are characterized by the same symmetry group; however, the coordination number of the vertices is variable. These Voronoi tessellations may be useful for the interpretation of the iso-symmetrical phase transitions.

The state detection of power cable is very important to ensure the reliability of power supply. Traditional sensors are mostly based on electric field detection, the operation is complex, and its efficiency needs to be improved. This paper optimizes the design and development of the magnetic field detection sensor for AC power cables. Firstly, through the establishment of the magnetic field sensor model, it is determined that permalloy is the material of the magnetic core, the optimal aspect ratio of the magnetic core is 20, and the ratio of coil length to core length is 0.3. Secondly, the coil simulation model is established, and it is determined that the optimal number of turns of the coil is 11000 turns, the diameter of the enamelled copper wire is 0.08mm, and the equivalent magnetic field noise of the sensor is 0.06pT. Finally, the amplifying circuit based on negative magnetic flux feedback is designed and the sensor is assembled, and the experimental circuit is built for sensitivity test. the results show that the sensitivity of the magnetic field sensor is 327.6mV/μT. The sensor designed in this paper has the advantages of small size, high sensitivity, easy to carry and high reliability.

Human Activity Recognition (HAR) technology enables continuous behavior monitoring, particularly valuable in healthcare. This study investigates the viability of using an ear-worn motion sensor for classifying daily activities, including lying, sitting/standing, walking, ascending stairs, descending stairs, and running. Fifty healthy participants (between 20 and 47 years old) engaged in these activities while under monitoring. Various machine learning algorithms, ranging from interpretable shallow models to state-of-the-art deep learning approaches designed for HAR, were employed for classification. Results demonstrate the ear sensor's efficacy, with deep learning models achieving 98% accuracy rate of classification. The obtained classification models are agnostic regarding which ear the sensor is worn and robust against moderate variations in sensor orientation (e.g., due to differences in auricle anatomy), meaning no initial calibration of the sensor orientation is required. The study underscores the ear's efficacy as a suitable site for monitoring human daily activity and suggests its potential for combining HAR with in-ear vital signs monitoring. This approach offers a practical method for comprehensive health monitoring by integrating sensors in a single anatomical location. This integration facilitates individualized health assessments, with potential applications in tele-monitoring, personalized health insights, and optimizing athletic training regimes.

Shape-shifting polymers are widely used in various fields such as intelligent switches, soft robots and sensors, which require both multiple stimulus response functions and qualified mechanical strength. In this study, a novel near infrared light (NIR) responsible shape-shifting hydrogel system was designed and fabricated, through embedding vinylsilane modified carbon nanotubes (CNTs) into particle-double network (P-DN) hydrogels by micellar copolymerization. The dispersed brittle Poly(sodium 2-acrylamido-2-methylpropane-1-sulfonate) (PNaAMPS) network of the microgels can serves as sacrificial bonds to toughen the hydrogels, and the CNTs endow it NIR photothermal conversion ability. The results show that the CNTs embedded P-DN hydrogels present excellent mechanical strength, i. e. fracture strength of 312 kPa and fracture strain of 357%. Moreover, an asymmetric bilayer hydrogel, where the active layer contains CNTs, can achieve 0°–110° bending deformation within 10 min under NIR irradiation and can realise complex deformation movement. This study provides a theoretical and experimental basis for the design and manufacture of photoresponsive soft actuators.

The aim of this study was to find a correlation between in vivo NIR scan patterns, oxidative status, and blood serum metabolites in rabbits fed diets protected or unprotected against oxidation. Rabbits does in groups of eight were fed for 9 weeks with diets containing linseed, rich in polyunsaturated fatty acids (LS), or linseed plus hazelnut skins, with antioxidant function (LS+HS), and palm oil, rich in saturated fatty acids (PO). The animals were examined at days 1, 31, and 63 using a smart SCÏO molecular sensor, a new miniaturized web-based wireless device, applied to the internal ear flap (NIR range 740-1070 nm). The hazelnut peels integrated diet protected the rabbits from the oxidative stress induced by the addition of unprotected polyunsaturated fats. NIR tomoscopy was variously correlated with serum parameters, lysozyme (R2=0.71), ROMs (0.47), cholesterol (0.49), triglycerides (0.40), and a multivariate Index of Oxidative Risk (0.67 [IOR]). The correlations suggested a close connection between the clustering of the diets according to the laboratory variables and the NIRS scan pattern clustering at the ending trial day, as shown by the highly significant odds ratios. Advantageous use of this simple, painless technique was evident in the planning phase, with no difference among the groups at the beginning of the study, but an effect size that evolved differently over time until the end of the study. In a practical validation of the SCÏO model in 92 commercial rabbit does, the average spread of the predicted IOR was 33% in lactating does (2.54±0.05) vs. dry does (1.91±0.07).

Application of the Ramsey graph theory to the analysis of physical systems is reported. Physical interactions may be very generally classified as attractive and repulsive. This classification creates the premises for the application of the Ramsey theory to the analysis of physical systems built of electrical charges, electric and magnetic dipoles. The notions of mathematical logic, such as transitivity and intransitivity relations, become crucial for understanding of the behavior of physical systems. The Ramsey theory explains why nature prefers cubic lattices over hexagonal ones for systems built of electric or magnetic dipoles. The Ramsey approach may be applied to the analysis of mechanical systems when actual and virtual paths between the states in the configurational space are considered. Irreversible mechanical and thermodynamic processes are seen within the reported approach as directed graphs. Chains of irreversible processes appear as transitive tournaments. These tournaments are acyclic; the transitive tournaments necessarily contain the Hamiltonian path. The set of states in the phase space of the physical system, between which irreversible processes are possible, is considered. The Hamiltonian path of the tournament emerging from the graph uniting these states is a relativistic invariant. Applications of the Ramsey theory to the general relativity become possible when the discrete changes in the metric tensor are assumed. Reconsideration of the concept of “simultaneity” within the Ramsey approach is reported.

We report the relative humidity (R.H.) sensing response of a resistive sensor, employing sensing layers based on a ternary nanohybrid comprising holey carbon nanohorns (CNHox), potassium chloride (KCl), and polyvinylpyrrolidone (PVP) at mass ratios 7/1/2, 6.5/1.5/2, and 6/2/2 (w/w/w/w). The sensing structure comprises a silicon substrate, a SiO2 layer, and interdigitated transducer (IDT) electrodes. The sensing film is deposited on the sensing structure via the drop-casting method. The sensing layers' morphology and composition are investigated through Scanning Electron Microscopy (S.E.M.) and RAMAN spectroscopy. The ternary hybrid-based thin film resistance increases when the sensors are exposed to R.H., ranging from 0% to 100%. The manufactured devices show a room temperature response comparable to a commercial capacitive R.H. sensor and are characterized by excellent linearity, rapid response time, and good sensitivity. The presented sensors exhibit superior performance in terms of sensitivity compared to other similarly manufactured and tested sensors that employ a CNHox-based sensing layer. We explain the sensing role of each constituent of the ternary hybrid nanocomposites based on their chemical and physical properties, electronic properties, and affinity for water molecules. Different alternative sensing mechanisms are considered and discussed, such as the decreasing number of holes in the holey CNHox at the interaction with water molecules, proton conduction, and PVP swelling.

Dairy products are an important source of protein and other nutrients in the Mediterranean diet. In these countries the most common source of milk for producing dairies are cow, goat, sheep and buffalo. Andalusia is traditionally the largest producer of goat milk in Spain. Kefir is a fermented product made from bacteria and yeasts which has health benefits beyond its nutritional properties. There is a lack of knowledge about the molecular mechanisms and metabolites that bring about these benefits. In this work, the combination of analytical techniques (GC-FID, UHPLC-MS-QToF, GC-QqQ-MS, and GC-ToF-MS) resulted in the detection of 105 metabolites in kefir produced with goat milk from two different thermal treatments (raw and pasteurized) fermented at four times (12, 24, 36, and 48 h, using 0 h as control). Of these, 27 metabolites differed between kefir produced with raw and pasteurized milk. These changes could be possibly caused by the effect of pasteurization on the microbial population in the starting milk. Some interesting molecules were identified, as shikimic acid, dehydroabietic acid, GABA and tyramine that could be related to antibacterial properties, enhance of immune system and arterial pressure. Moreover, a viability assay of the NIRS technique was performed to evaluate its use on monitoring the fermentation and classification of samples, which had resulted in a 90 % of correct classified samples according to their fermentation time. This study represents the most comprehensive metabolomic analysis of goat milk kefir so far, revealing the intricate changes in metabolites during fermentation and the impact of milk treatment.

The notion of the informational measure of symmetry is introduced according to: HsymG=-i=1kPGilnPGi, where PGi is the probability of appearance of the symmetry operation Gi within the given 2D pattern. HsymG is interpreted as an averaged uncertainty in the presence of symmetry elements from the group G in the given pattern. The informational measure of symmetry of the “ideal” pattern built of identical equilateral triangles is established as HsymD3=1.792. The informational measure of symmetry of the random, completely disordered pattern is zero, Hsym=0. Informational measure of symmetry is calculated for the patterns generated by the P3 Penrose tessellation. Informational measure of symmetry does not correlate neither with the Voronoi entropy of the studied patterns nor with the continuous measure of symmetry of the patterns.

An easy to implement and cost-effective Fiber Bragg Grating (FBG) sensor interrogation technique based on a ring Erbium-Doped Fiber Laser (EDFL) topology is proposed and experimentally assessed. The FBG sensor is part of the EDFL cavity and must have a central wavelength located within the linear region of the EDF’s amplified spontaneous emission (ASE) spectrum which occurs between 1530 and 1540nm. In this manner, the wavelength-encoded response of the FBG under strain is converted to a linear variation of the laser output power, removing the need for spectrum analysis as well as any limitations from the use of external edge-filtering components. In addition, the laser linewidth is significantly reduced with respect to the FBG bandwidth thus improving the resolution of the system, whereas its sensitivity can be controlled through the pumping power. The performance of the system has been characterized by modeling and experiments for EDF's with different lengths, doping concentrations and pumping power levels. The influence of mode-hopping in the laser cavity on the resolution and accuracy of the system has also been investigated.

This work shows a correlation between light reflectance, absorption, and morphologies of series of (1-x) BM–x PT, (x = 0.0, 0.02, 0.04, 0.08, 0.12, 0.16, 0.24) ceramics composite. The (1-x) BM–x PT showed features of a black mirror with a low optical energy gap. The measured Vis-NIR diffused reflectance enabled the calculation of the energy gap using the modified Kubelka-Munk function. The estimated energy gap was lower than 1.5 eV related to low reflectance in the Vis-NIR range. Moreover, obtained histograms of grains, using scanning electron microscope, enabled the correlation between grains size and amount of lead titanate. We deduced from the ceramics surface morphology that marked porosity also induced reflectivity of low magnitude. We correlated the magnitude of the energy gap with phases of the BM-PT composite and with the electrical conductivity activation energy reported in the literature. Our results findings opened prospect studied materials for optical applications.

A reliable and efficient rail track defect detection system is essential for maintaining rail track integrity and avoiding safety hazards and financial losses. Eddy current (EC) testing is a non-destructive technique that can be employed for this purpose. The trade-off between spatial resolution and lift-off should be carefully considered in practical applications to distinguish closely spaced cracks such as those caused by rolling contact fatigue (RCF). A multi-channel eddy current sensor array has been developed to detect defects on rails. Based on the sensor scanning data, defect reconstruction along the rails is achieved using an inverse algorithm that includes both direct and iterative approaches. In experimental evaluations, the EC system with the developed sensor is used to measure defects on a standard test piece of rail with a probe lift-off of 4-6 mm. The reconstruction results clearly reveal cracks at various depths and spacings on the test piece.

The application of artificial intelligence to point-of-care testing (POCT) disease detection has become a hot research field, in which breath detection which detects the patient's exhaled VOCs combined with sensor arrays of Convolutional Neural Network (CNN) algorithms as a new lung cancer detection is attracting more researchers' attention. However, due to low accuracy, high complexity computation and large number of parameters make the CNN algorithms difficult transplant to the embedded system of POCT devices. A lightweight neural network (LTNet) in this work is proposed to deal with this problem, and meanwhile, achieve high-precision classification of acetone and ethanol gases, which are respiratory markers for lung cancer patients. Compared to currently popular lightweight CNN models such as EfficientNet, LTNet has fewer parameters (32K) and its training weight size is only 0.155 MB. LTNet achieved an overall classification accuracy of 99.06% and 99.14% in the own mixed gas dataset and the University of California (UCI) dataset, which are both higher than that of the five existing models’, and it also offers the shortest training (844.38s and 584.67s) and inference time (23s and 14s) in the same validation set. Compared to the existing CNN models, LTNet is more suitable for resource-limited POCT devices.

The importance of conflict analysis and safety considerations during work zone intervals at signalized intersections cannot be overstated, as these periods pose unique challenges and safety risks for both motorists and pedestrians. Work zones introduce temporary changes to traffic patterns, lane configurations, and signal timings, which can disrupt the flow of traffic and increase the likelihood of conflicts between vehicles and pedestrians. By conducting comprehensive conflict analysis, it is possible to identify potential conflict points, such as merging areas, pedestrian crossings, and lane transitions, and implement targeted safety measures to mitigate risks. Additionally, considering safety considerations during work zone intervals is paramount to safeguarding the well-being of road users and minimizing the occurrence of conflicts or collisions. Measures such as enhanced signage, temporary traffic control devices, and increased enforcement efforts can help promote compliance with traffic regulations and ensure the safe passage of vehicles and pedestrians through work zones. This study investigates the dynamics of traffic behavior and safety implications within work zones at signalized intersections, aiming to address key challenges and enhance intersection management strategies. Through comprehensive analysis, varying frequencies of Vehicle-to-Vehicle (V2V) conflicts were observed across different movement directions, with significant occurrences identified in specific phases of the traffic signal cycle. Specifically, 69 V2V conflicts in phase #1, 181 in phase #2, 31 in phase #3, 207 in phase #4, 1 in phase #5, 274 in phase #6, 93 in phase #7, and 186 in phase #8 were recorded. Furthermore, the examination of Vehicle-to-Pedestrian (V2P) conflicts underscored the importance of prioritizing pedestrian safety, with notable occurrences observed in phases associated with pedestrian crossing movements. Meanwhile, despite the closure of left-turn movements, instances of red light running persisted, with 69 red light running events in phase #1, 181 in phase #2, 31 in phase #3, 207 in phase #4, 1 in phase #5, 274 in phase #6, 93 in phase #7, and 186 in phase #8.To mitigate these safety concerns during work zone intervals, proactive measures are essential. Strategies include improving communication through clear signage and advanced warning systems, enhancing enforcement efforts with red light cameras and increased police presence, and investing in infrastructure improvements such as temporary pedestrian facilities. Integration of real-time data from sensors, particularly LiDAR technology, offers significant advantages in detecting conflicts and red light runners during work zone intervals. LiDAR's precise, real-time data on vehicle and pedestrian movements, combined with its 360-degree coverage and high spatial resolution, facilitates accurate detection and tracking of potential conflict scenarios, contributing to enhanced intersection safety and traffic management efficiency. This study endeavored to conduct a traffic safety analysis during work zone intervals at a signalized intersection in Baltimore City, known for its high rate of traffic crashes, utilizing LiDAR sensor technology.

This paper presents a two-stage ADC based on pseudo-differential operational transconductance amplifier (OTA), which is designed for the readout circuit of X-ray linear array sensor. This hybrid ADC employs an incremental sigma-delta ADC and a cyclic ADC, achieving a good trade-off between accuracy and conversion speed. The two stages share the same hardware to reduce power consumption and die area. A common-mood feedback module is used to suppress the influence of charge injection, and the effectiveness is demonstrated by detailed theoretical analysis. A test chip of 14-bit ADC is fabricated in 0.35μm CMOS technology. The measured root mean square (RMS) value of DNL is 0.254 LSB, and the maximum value of INL is -0.776/+1.56 LSB. The measured effective number of bits (ENOB) is 13.43 bits.

This paper focuses on optimal sensor positioning for monitoring activities of daily living and investigates different combinations of features and models on different sensor positions, i.e., the side of the waist, front of the waist, chest, thigh, head, upper arm, wrist, and ankle. Sixteen features are extracted and the feature importance is measured by using the Relief-F feature selection algorithm. Eight classification algorithms are evaluated on a dataset collected from young subjects and that collected from elderly subjects, with two different experimental settings. To deal with different sampling rates, signals with a high data rate are down-sampled and a transformation matrix is used for aligning signals to the same coordinate system. The thigh, chest, side of the waist, and front of the waist are the best four sensor positions for the first dataset (young subjects), with average accuracy values being greater than 95%. The best model obtained from the first dataset for the side of the waist is validated on the second dataset (elderly subjects). The most appropriate number of features for each sensor position is reported. The results provide a reference for building activity recognition models for different sensor positions, as well as for data acquired from different hardware platforms and subject groups.

In the context of improving aircraft safety, this study focuses on the development and evaluation of a graphene-based ice detection system using an environmental chamber. The research is driven by the need for more accurate and efficient ice detection methods, crucial in mitigating in-flight icing hazards. The methodology employed involves testing flat graphene-based sensors in a controlled environment, simulating a variety of climatic conditions that could be experienced in an aircraft during its entire flight. The environmental chamber enabled precise manipulation of temperature and humidity levels, thereby providing a realistic and comprehensive test bed for sensor performance evaluation. The results were significant, revealing the graphene sensors’ heightened sensitivity and rapid response to the subtle changes in environmental conditions, especially the critical phase transition from water to ice. This sensitivity is the key to detecting ice formation at its onset, a critical requirement for aviation safety. The study concludes that graphene-based sensors, tested under varied and controlled atmospheric conditions, exhibit a remarkable potential in enhancing ice detection systems for aircraft. Their lightweight, efficient and highly responsive nature makes them a superior alternative to traditional ice detection technologies, paving the way for more advanced and reliable aircraft safety solutions.

Voronoi mosaics inspired by the seed points placed on the Archimedes Spirals are reported. Voronoi entropy was calculated for these patterns. Equidistant and non-equidistant patterns are treated. Voronoi mosaics built from a sells of equal size which are of a primary importance for decorative arts are reported. The pronounced prevalence of hexagons is inherent for the patterns with an equidistant and non-equidistant distribution of points, when the distance between the seed points is of the same order of magnitude as the distance between the turns of the spiral. Penta- and heptagonal “defected” cells appeared in the Voronoi diagrams due to the finite nature of the pattern. The ordered Voronoi tessellations demonstrating the Voronoi entropy larger than 1.71, reported for the random 2D distribution of points, were revealed. The dependence of the Voronoi entropy on the total number of the seed points located on the Archimedes Spirals is reported. Voronoi tessellations generated by the phyllotaxis-inspired patterns are addressed. The aesthetic attraction of the Voronoi mosaics arising from seed points placed on the Archimedes Spirals is discussed.

Wireless Powered Communication Networks (WPCN), which has attracted much attention of researchers, also been recently recommended in 5^th generation (5G) wireless networks. With the help of the WPCN, the reliability and battery life of wireless low-power devices can be improved. In this paper, we investigate throughput and ergodic capacity in WPCN-assisted amplify-and-forward (AF) relaying system, considering two transmission modes including delay-tolerant and delay-limited. As important achievement, we propose symmetric energy harvesting protocol, namely time power switching relaying (TPSR) in order to find maximal throughput. In particular, both time switching and power switching coefficients in this schemes are considered. Unlike most of the previous works, we further focus on impact of outdated channel state information (CSI) in this WPCN. In order to evaluate information processing efficiency, the performance can be substantially improved by optimally harvesting time and power coefficients of the received signal at relay node for energy and information extraction, and by deploying several scenarios. By deploying Monte Carlo simulation, it is confirmed that the system performance is more sensitive to CSI estimation error, noise variance, signal-to-noise ratio (SNR) and resulting in other reasonable computations of TPSR need be deployed to obtain QoS requirement.

Paraffin wax stores energy in the form of latent heat at a nearly constant temperature during melting and releases this energy during solidification. This effect is used in industrial energy storage. An unusual change in the shape of a melted droplet of paraffin wax placed on a relatively cold glass plate is studied. As the droplet solidifies, its upper surface becomes nearly flat and a dimple is formed in the center of this surface, making the droplet look like a fruit (pumpkins are more commonly shaped like this, but the authors prefer apples). A series of experiments, as well as physical and numerical modeling of the droplet's thermal state, taking into account the formation of a mushy zone between liquidus and solidus, made it possible to understand the role of gravity and gradual increase in viscosity and density of paraffin wax on changing the droplet shape and, in particular, to clarify the mechanism of formation of the dimple on its upper.

Water resources planners and policymakers often ask questions about the future projections of drought characteristics (events, intensity, severity, duration, and peak) under different climatic scenarios. This study focused on quantifying the historical (1951-2005) and future (2026-2100) drought characteristics using the Standardized precipitation index (SPI) under RCP 4.5 and RCP 8.5 climate scenarios for the Balochistan province of Pakistan, an arid and drought-vulnerable region. Precipitation data of MPI-ESM-LR_RCA4 RCM was obtained from the Coordinated Regional Climate Downscaling Experiment South Asia (CORDEX-SA). The CORDEX-SA data was interpolated at 12-gauge stations and bias-corrected by the distribution mapping method using Asian Precipitation - Highly-Resolved Observational Data Integration towards Evaluation (APHRODITE) data. The drought characteristics were calculated based on standardized precipitation index (SPI), and intercompared between northern Balochistan (NB) and southern Balochistan (SB). It was found that the northern Balochistan (NB) region has suffered more droughts in the historical period and is also projected to have more severe and intense droughts than SB region. It was also found that with the increase of drought events, the duration reduces, which means that the higher the drought events at a station, the lower the drought duration. Government officials should focus more on managing the already few freshwater resources sustainably, given the increased likelihood of droughts in Balochistan due to climate change.

In this contribution, we present a high-speed multiplex grating spectrometer based on a spectral coding approach that is founded on principles of compressive sensing. The spectrometer employs a single-pixel InGaAs detector to measure the signals encoded by an amplitude spatial light modulator (digital micromirror device, DMD). This approach leads to a speed advantage and multiplex sensitivity advantage atypical for standard dispersive systems. Exploiting the 18.2 kHz pattern rate of the DMD, we demonstrate 4.2 ms acquisition times for full spectra with a bandwidth of 450 nm (5250 cm-1 – 4300 cm-1; 1.9 µm – 2.33 µm). Due to the programmability of the DMD, spectral regions of interest can be chosen freely, thus reducing acquisition times further, down to the sub-millisecond regime. The adjustable resolving power of the system accessed by means of computer simulations is discussed, quantified for different measurement modes, and verified by comparison with a state-of-the-art Fourier-transform infrared spectrometer. We show measurements of characteristic polymer absorption bands in different operation regimes of the spectrometer. The theoretical multiplex advantage of 8 was experimentally verified by comparison of the noise behavior of the spectral coding approach and a standard line-scan approach.

The market for autonomous vehicles (AV) is expected to experience significant growth over the coming decades and to revolutionize the future of transportation and mobility. The AV is a vehicle that is capable of perceiving its environment and perform driving tasks safely and efficiently with little or no human intervention and is anticipated to eventually replace conventional vehicles. Self-driving vehicles employ various sensors to sense and perceive their surroundings and, also rely on advances in 5G communication technology to achieve this objective. Sensors are fundamental to the perception of surroundings and the development of sensor technologies associated with AVs has advanced at a significant pace in recent years. Despite remarkable advancements, sensors can still fail to operate as required, due to for example, hardware defects, noise and environment conditions. Hence, it is not desirable to rely on a single sensor for any autonomous driving task. The practical approaches shown in recent research is to incorporate multiple, complementary sensors to overcome the shortcomings of individual sensors operating independently. This article reviews the technical performance and capabilities of sensors applicable to autonomous vehicles, mainly focusing on vision cameras, LiDAR and Radar sensors. The review also considers the compatibility of sensors with various software systems enabling the multi-sensor fusion approach for obstacle detection. This review article concludes by highlighting some of the challenges and possible future research directions.

Exploring the relationship between cereal yield and remotely sensed normalized difference vegetation index (NDVI) is of great importance to decision-makers and agricultural stakeholders. In this study, an approach based on the Pearson correlation coefficient and linear regression method is carried out to reveal the relationship between cereal yield and Moderate Resolution Imaging Spectroradiometer (MODIS) NDVI data in the Fez-Meknes region of Morocco. The results obtained show strong correlations reaching 0.70 to 0.89 between NDVI and grain yield. The linear regression model explains 58 to 79% of the variability in yield in regional provinces marked by the importance of cereal cultivation, and 51 to 53% in the mountainous provinces with less agricultural land devoted to major cereals. The regression slopes indicate that a 0.1 increase in NDVI results in an expected increase in grain yield of 4.9 to 8.7 quintals (q) per ha, with an average of 6.8 q/ha throughout the Fez-Meknes region. RMSE ranges from 2.12 to 4.96 q/ha. These results are promising in terms of early yield forecasting based on MODIS NDVI data.

A compact Mach-zehnder interferometer with a novel design of directional couplers and a phase shifter has been presented as a thermo-optical sensor. With the aim of reducing device size to micro and nano dimension silicon-on-insulator technology was employed. That allowed miniaturization of device size through the reduction of its cross sectional area to 0.066 µm² and the radius of curvature of both the arms of the directional coupler and S-bends of the phase shifter to 5 µm and C-bends to 3 µm. These nano size device dimensions made it possible to reduce the coupling gap to 0.2 µm, which resulted in a significant reduction in the coupling length. The device geometry and its performance characteristics were analyzed and optimized using coupled mode analysis and finite difference time domain simulation tools, respectively. The wavelength dependent transmission loss of the device was measured at different temperature to verify and validate its performance characteristics. Tested devices showed a remarkable temperature dependent transmission characteristic offering significant changes in transmission loss band – with as low as 0.45 ⁰C change in substrate temperature. The extinction ratio and the free spectral range of the device were 26 dB and 0.26 nm respectively in the wavelength range of 1549.5 nm – 1550.5 nm. These results imply that the devices presented here can be used as compact and highly sensitive thermal sensors and optical switches.

A space charge density wireless measurement system based on the idea of distributed measurement is proposed for collecting and monitoring the space charge density in an ultra-high-voltage direct-current (UHVDC) environment. The proposed system architecture is composed of a number of wireless nodes connected with space charge density sensors and a base station. The space charge density sensor based on atmospheric ion counter method is elaborated and developed, and the ARM microprocessor and Zigbee radio frequency module are applied. The wireless network communication quality and the relationship between energy consumption and transmission distance in the complicated electromagnetic environment is tested. Based on the experimental results, the proposed measurement system demonstrates that it can adapt to the complex electromagnetic environment under the UHVDC transmission lines and can accurately measure the space charge density.

Separase is a key cysteine protease to separate sister chromatids through digestion of cohesion ring that inhibits chromosome segregation as trigger of metaphase–anaphase transition in eukaryotes and highly regulated its activity by binding with securin and cyclinB-CDK1 complex. Those bindings prevent proteolytic activity of separase until the onset of anaphase. Chromosome missegregation and aneuploidy are frequently observed in malignancies. However, there are some difficulties for biochemical examinations due to instability of separase in vitro and a few spatiotemporal resolution approaches monitoring live separase activity throughout mitotic processes. Here we have developed FRET-based molecular sensors including GFP variants with separase cleavable sequences as donor and covalently attached fluorescent dye as acceptor molecules applicable to conventional live cell imaging and flow cytometric analysis because of efficient live cell uptake. We investigated performance of equivalent molecular sensors localized or not localized inside nucleus under cell cycle control using flow cytometry. Synchronized cell cycle progression rendered significant separase activity detections in both molecular sensors. We obtained consistent outcomes with localized molecular sensor introduction and cell cycle control by fluorescent microscopic observations. We thus established live cell separase activity monitoring systems specifically or statistically that could lead to elucidate separase properties in detail.

The pharmaceutical industry is making significant strides in enhancing process comprehension through the development of concepts like Quality by Design (QbD) and Process Analytical Technology (PAT). This shift has moved from traditional offline testing methods to real-time estimation of product quality. The dissolution characteristics of pharmaceutical tablets play a crucial role in maximizing the release of medications and their bioavailability. One factor that can affect dissolution is the blending procedure. Inadequate mixing can lead to patches of concentrated active components or excipients within the tablet, resulting in inconsistent dissolution behavior. A study investigated the impact of blending time and speed on the dissolution behavior of Amlodipine tablets using near-infrared (NIR) spectroscopy and multivariate modeling. NIR spectra were collected for Amlodipine tablets produced under various blending conditions using a 2-level central composite design. Dissolving profiles were analyzed using a USP dissolution device. Multivariate analysis techniques, including principal component analysis (PCA), partial least squares (PLS), Support Vector Machine (SVM), and Artificial Neural Networks (ANN), were applied to the collected NIR spectra. The findings demonstrated that blending speed and time had a significant influence on the dissolving properties of Amlodipine tablets. Blending at faster speeds and for shorter durations resulted in excessive shear and insufficient mixing, ultimately reduced drug release. The multivariate models constructed using ANN outperformed SVM and PLS in predicting dissolution profiles based on NIR spectra. This research highlights the effectiveness of NIR spectroscopy and multivariate modeling in optimizing tablet dissolution. These advancements enable continuous manufacturing of high-quality pharmaceutical products.

Lanthanide-doped upconversion nanoparticles (UCNPs) are promising bioimaging nanoprobes due to their excellent photostability. As one of the most commonly-used lanthanide activators, Tm3+ ions have perfect ladder-type electron configuration and can be directly excited by bio-friendly near-infrared-II (NIR-II) wavelengths. Here, the emission characteristics of Tm3+-doped nanoparticles under laser excitations of different near-infrared-II wavelengths were systematically investigated. The 1064 nm, 1150 nm and 1208 nm lasers are proposed to be three excitation strategies with different response spectra of Tm3+ ions. Particularly we found that 1150 nm laser excitation enables intense three-photon 475 nm emission, which is nearly 100 times stronger than that excited by 1064 nm excitation. We further optimized the luminescence brightness after investigating the luminescence quenching mechanism of bare NaYF4:Tm (1.75%) core. After growing inert shell, ten-fold increase of emission intensity was achieved. Combining the advantages of NIR-II wavelength and the higher-order nonlinear excitation, a promising facile excitation strategy was developed for the application of thulium-doped upconversion nanoparticles in single nanoparticle imaging and cancer cell microscopic imaging.

The color and NIR spectrum are key to build an oil estimation model, thus it requires individual olives clustering before the Sohlext oil extraction method can be applied. The objective was to analyze an OC estimation model of individual olives, based on cluster of similar color and NIR spectrum in different combination of the first and/or the second season. This study was performed with Chilean Arbequina olives in 2016 and 2017. The descriptor of the cluster consisted of the 3 color channels of c1, c2, c3 color model plus 11 reflectance points between 1710 and 1735 nm of each olive, normalized with the Z-score index. Clusters of similar color and NIR spectrum were formed with the k-means++ algorithm, leaving a sufficient amount of olives to be able to perform the Sohlext analysis of OC, as reference value. The estimation models were based on the Support Vector Machine. The test was carried out with the Leave One-Out Cross Validation in different training-testing combinations. The best model predicted the OC with 6% and 13%deviation respect to the real value in one season by itself and when one season tested with another season, respectively. The use of clustering in estimation model is discussed.

In the present work, we designed a mild strategy to make Cu₂(OH)PO₄ (CHP) nanoparticles on cotton fabrics (CFs) to achieve multi-functionalities. The phytic acid (IP6) assisted method was employed to synthesize nanoparticles (CHP-IP6). Under Fourier-transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), scanning electron microscopy (SEM), energy-dispersive X-ray (EDX), transmission electron microscope (TEM), X-ray photoelectron spectroscopy (XPS) as well as thermogravimetric analysis (TGA), we characterized the coated cotton fabrics. The CHP-IP6 treated fabrics showed prominent photocatalytic activity, excellent photocatalytic stability and thorough discoloration of methylene blue (MB) stain under sunlight irradiation.

Properties of the Voronoi tessellations arising from the random 2D distribution points are reported. We applied the procedure of dividing the sides of Voronoi cells into equal or random parts to Voronoi diagrams generated by a set of randomly placed on the plane points. The dividing points were then used to construct the following Voronoi diagram. Repeating this procedure led to a surprising effect of positional ordering of Voronoi cells, reminiscent of the formation of lamellae and spherulites in linear semi-crystalline polymers and metallic glasses. Thus, we can conclude, that by applying even a simple set of rules to a random set of seeds we introduce order into an initially disordered system. At the same time, the Voronoi entropy showed a tendency to values typical for completely random patterns and did not distinguish the short-range ordering. The Voronoi entropy and the continuous measure of symmetry of the patterns demonstrated the distinct asymptotic behavior, while approaching the close saturation values with the increase of the number of the iteration steps. Voronoi entropy grew, with the number of iterations, whereas the continuous measure of symmetry of the same patterns demonstrated the opposite asymptotic behavior. The Voronoi entropy is not an unambiguous measure of order in the 2D patterns. The more symmetrical patterns may demonstrate the higher values of the Voronoi entropy.

The development of new cultivars is important for the profitability of the floriculture industry. There are a limited number of cultivars of Zantedeschia aethiopica, an iconic ornamental cut flower, garden plant, and potted plant, due to the incompatibility of interspecific crossings within the genus. Most present-day varieties are the result of spontaneous mutations or classical breeding within the species, followed by a long selection process. Breeders are very interested in the development of a time- and cost-effective method for producing new Z. aethiopica cultivars with novel characteristics. Here, Z. aethiopica mutants were generated by treating seeds with 100 Gy of X-ray radiation. The resulting putative mutants were selected based on particular flowering parameters and compared to non-irradiated, control plants. Over two growing seasons, characteristics such as early flowering, flower size and shape, yield and response to soft-rot disease were monitored and considerable variation was observed among the mutated lines. Out of 319 mutants, 20 lines were selected based on their phenotypes and then propagated and further analyzed. Within this group, only two phenotypes displayed at least five improved flowering properties under natural, Mediterranean conditions. The rest displayed two to four desired combinations of flowering traits, some with great commercial potential.

Brushless Synchronous Machines (BSM) are replacing conventional synchronous machines with static excitation in generation facilities due to the absence of sparking and lower maintenance. However, this excitation system makes challenging measuring electric parameters in the rotor. This fact highly difficult the detection of ground faults, which are the most common type of electrical fault in electric machines. In this paper, a ground fault detection method for BSM is proposed. It is based on an inductive AC/DC rotating current sensor installed in the shaft. In case of a ground fault in the rotating parts of the BSM, a fault current will flow through the rotor’s sensor, inducing voltage in its stator. Analyzing the frequency components of the induced voltage the detection of a ground fault in the rotating elements is possible. The ground faults detection method proposed covers the whole rotor and discern between DC and AC sides. To corroborate the detection method, experimental tests have been performed using a prototype of this sensor connected to laboratory synchronous machines achieving satisfactory results.

Franklinite-Zincochromite-Gahnite solid solutions have been prepared by ceramic or coprecipitation method and its pigmenting capacity as cool ceramic pigments in different glazes (double and single firing frits and porcelain frit) was studied. XRD, UV-Vis-NIR diffuse reflectance, CIEL*a*b* colour analysis, bandgap measurement and the photocatalytic activity over the Orange II azoic dye were carried out for the characterization of samples. Following criteria of high red colouring capacity and high NIR reflectance at minimum Cr amount, Zn(Fe1.8Cr0.2), Zn(Al1.5Cr0.5) and Zn(Al1.3Cr0.5Fe0.2)O4 turn out to be the optimal compositions for an intense reddish cool pigment. All powders show a direct semiconductor behaviour with bandgap around 2 eV, falling in the visible range (620 nm), and according to literature, the associated photocatalytic activity over Orange II with visible light irradiation is moderate in all cases, but the Franklinite-Zincochromite Zn(Fe1.8Cr0.2) stands out.

A non-destructive analysis of proximate parameters (moisture content, MC; volatile matter, VM; fixed carbon, FC; and ash content) for a variety of chipped and ground biomasses was investigated through a combination of thermogravimetric analysis (TGA) and near-infrared spectroscopy (NIRS) with partial least squares regression (PLSR). In this study, the thermogravimetric method was employed as a tool to determine the proximate analysis data of biomass samples through TG and DTG curves, which were generated by tracking changes in biomass mass loss over time or temperature. NIRS non−destructively scanned the chipped biomass in diffuse reflectance while ground biomass using transflectance mode, covering the wavenumber range of 3594.87 to 12,489.48 cm−1. The PLSR−based models: Full−PLSR, genetic algorithm (GA)−PLSR, successive projection algorithm (SPA)−PLSR, the spectral multi−preprocessing (MP) PLSR− 5 range method, and the MP PLSR−3 range method were developed. Model performance was assessed, compared, and selected based on the coefficient of determination in the prediction set (R2P), root mean square error in the validation set (RMSEP), and the ratio of prediction to deviation (RPD). Based on the comprehensive analysis of model performance, MC and FC models of chip biomass have demonstrated satisfactory performance which makes it applicable cautiously in any application, including research. The optimum models for MC and FC in chip biomass were constructed using GA−PLSR with 2nd derivative and Full−PLSR with a constant offset, resulting in R2P values of 0.8654 and 0.8773, RMSEP values of 0.85% and 2.12%, and RPD values of 2.9 and 3.0, respectively. Other parameters such as MC and FC in ground biomass as well as VM and ash content in both chip and ground biomass were found suitable for rough screening. The sensitivity of the selected model was assessed by calculating the limit of quantification (LOQ), and the results indicated that the calculated LOQ values for VM in both chip and ground biomass and FC in chip biomass are lower than the minimum reference values used during model development, signifying a high level of sensitivity. However, for the remaining parameters, the LOQ values surpass the established minimum reference value, suggesting the model could not predict the future samples with reference value lower than the calibration range. Nevertheless, enhancing the models by incorporation an ample number of representative biomass samples and consistently validating the models with unknown samples is imperative to ensure accurate predictions.

Agricultural soils serve as crucial storage sites for soil organic carbon (SOC). Their appropriate management is pivotal for mitigating climate change. To evaluate spatial and temporal changes in SOC within agricultural fields, continuous monitoring is imperative. In-field data sets of Vis-NIR soil spectra were collected on a long-term experimental site using an on-the-go spectrophotometer. Data processing for continuous SOC prediction involves a two-steps modelling approach. In Step 1, a Partial Least Square (PLSR) regression model is trained to establish a relationship between the SOC content and the spectral information also including spectral preprocesisng. In Step 2, the predicted SOC content obtained from the PLSR models is interpolated using ordinary kriging. Among the tested spectral preprocessing techniques and semivariogram models, SG and gapDer preprocessing along with a Gaussian semivariogram model, yielded the best performance resulting in a root mean square error of of 1.24 and 1.26 g kg-1. A striping effect due to the transect-based data collection was addressed by testing the effectiveness of extending the spatial separation distance, employing data aggregation, and defining the distribution based on treatment plots using block kriging. Overall, the results highlight the immense potential of on-the-go spectral Vis-NIR data for field-scale spatial-temporal monitoring of SOC.

in our increasingly interconnected world, sensor networks are critical in gathering and sending data for various applications, from environmental monitoring and industrial automation to healthcare and smart cities. However, as sensor networks expand in importance, so does the need to solve the multidimensional concerns of security, privacy, and forensics. This article explores the complex world of sensor network security, the delicate balance between data privacy and utility, and the emerging area of sensor network forensics. This article focuses on risk assessment of a network.

In this study, a novel flexible ethanol gas sensor was created by the deposition of CoFe2O4 (CFO) thin film was on a thin mica substrate using pulsed laser deposition. Transition electron microscopy (TEM) investigations clearly demonstrated the successful growth of CFO on the mica, where a well-defined interface was observed. Ethanol gas-sensing studies showed optimal performance at 200 °C, with the highest response, 19.2, to 100 ppm ethanol. Operating the sensor in self-heating mode under 7 V applied voltage, which was corresponds to a temperature of approximately 200 °C, produced a maximal response to ethanol of 19.2. This aligned with the highest responses observed during testing at 200 °C, confirming the sensor’s accuracy and sensitivity to ethanol under self-heating conditions. In addition, the sensor exhibited good selectivity to ethanol and excellent flexibility; maintaining its high performance after bending and tilting up to 5000 times. As this is the first report on flexible self-heated CFO gas sensors, we believe that this research holds great promise for the future development of high-quality sensors based on this approach.

A milk drink flavored with dates syrup produced at a lab scale level was evaluated. The production process of date syrup involves a sequence of essential unit operations, commencing with the extraction, filtration, and concentration processes from two cultivars: Sukkary and Khlass. Date syrup was then mixed with cow’s and camel’s milk at four percentages to form a nutritious, natural, sweet, and energy milk drink. Sensory, physical, and chemical characteristics of the milk drinks flavored with date syrup were examined. The objective of this work was to measure physiochemical properties of dates fruits and milk drinks flavored with dates syrup, then to evaluate the physical properties of milk drinks utilizing a non-destructive NIR spectra. The study assessed the characteristics of the milk drink enhanced with date syrup by employing near-infrared spectra (NIR) spectra and analyzed utilizing partial least-square regression (PLSR) and artificial neural network (ANN) analysis. The NIR spectrum proved to be highly effective in estimating the physiochemical attributes of the flavored milk drink. The ANN model outperformed the PLSR model in this context. RMSECV is considered a more reliable indicator of a model's future predictive performance compared to RMSEC, R2 ranged between 0.946 and 0.989. Consequently, non-destructive NIR technology demonstrates significant promise for accurately predicting and contributing to the entire production process of the product's properties examined.

The flour milling industry, a vital component of global food production, is undergoing a transformative phase driven by the integration of smart devices and advanced technologies. This transition promises improved efficiency, quality, and sustainability in flour production. Accurate estimation of protein, moisture and ash content in wheat grains and flour is of paramount importance due to their direct impact on product quality and compliance with industry standards. This paper explores the application of Near-Infrared (NIR) spectroscopy as a non-destructive, efficient, and cost-effective method for measuring the aforementioned essential parameters in wheat and flour, by investigating the effectiveness of a low-cost handle NIR spectrometer. Furthermore, a novel approach using Fuzzy Cognitive Maps (FCMs) is proposed to estimate protein, moisture and ash content in grain seeds and flour, marking the first known application of FCMs in this context. Our study includes an experimental setup that assesses different types of wheat seeds and flour samples and evaluates three NIR pre-processing techniques to enhance parameter estimation accuracy. The results indicate that low-cost NIR equipment can contribute to the estimation of the under-study parameters.

Beans are the most widely used protein source in the world and their productivity is directly linked to nitrogen (N). The short crop cycle imposes the need for fast methodologies for N quantification. In this work, we evaluated the performance of four machine learning algorithms in nitrogen prediction using NIR spectroscopy. Increasing doses of nitrogen were applied to the plants and leaf reflectance was collected. Weka software was used to test the algorithms. The selection of the most effective spectral zones was made with the VIP. Considering predictions with the whole NIR, the best results were achieved with RF (R2 = 0,84 and RMSE = 2,69 g kg-1) and KNN (R2 = 0,77 and RMSE = 3,86 g kg-1). The intervals of 700-740 nm and 983-995 nm were considered the most important for the study of N. More efficient predictions were verified when only spectral regions screened by VIP were included, increasing the accuracy of the RF, KNN and M5 models by 6%, 4% and 8%, respectively. The efficiency of N prediction based on NIR reflectance combined with machine learning was verified. This approach can optimize the management of nitrogen fertilization, serving as an important tool in precision agriculture.

In this work we theoretically investigate the responsivity/noise equivalent power (NEP) trade-off in graphene/semiconductor Schottky photodetectors (PDs) operating in the near-infrared regime and working at room temperature. Our analysis shows as the responsivity/NEP ratio is strongly dependent on the Schottky barrier height (SBH) of the junction and we derive a closed analytical formula for maximizing it. In addition, we theoretically discuss as the SBH is linked to the bias applied to the junction in order to show how these devices could be optimized in practice for different semiconductors. We discover that graphene/n-silicon (Si) Schottky PDs could be optimized at 1550nm showing a responsivity and NEP of 133mA/W and 500fW/Hz, respectively, by a low reverse bias of only 0.66V. Moreover, we show that graphene/n-germanium (Ge) Schottky PDs optimized in term of responsivity/NEP ratio could be employed at 2000nm with a responsivity and NEP of 233mA/W and 31pW/Hz, respectively. We believe that our insights are of great importance in the field of silicon photonics for the realization of Si-based PDs to be employed in power monitoring, lab-on-chip and environment monitoring applications.

Visible and near-infrared reflectance (Vis–NIR) techniques are a plausible method to soil analyses. The main objective of the study was to investigate the capacity to predicting soil properties Al, Ca, K, Mg, Na, P, pH, total carbon (TC), H and N, by using different spectral (350–2500 nm) pre-treatments and machine learning algorithms such as Artificial Neural Network (ANN), Random Forest (RF), Partial Least-squares Regression (PLSR) and Cubist (CB). The 300 soil samples were sampled in the upper part of the Itatiaia National Park (INP), located in Southeastern region of Brazil. The 10 K-fold cross validation was used with the models. The best spectral pre-treatment was the Inverse of Reflectance by a Factor of 104 (IRF4) for TC with CB, giving an averaged R² among the folds of 0.85, RMSE of 1.96; and 0.67 with 0.041 respectively for H. Into the K-folds models of TC, the highest prediction had a R² of 0.95. These results are relevant for the INP management plan, and also to similar environments. The good correlation with Vis–NIR techniques can be used for remote sense monitoring, especially in areas with very restricted access such as INP.

The integration of Wireless Sensor Networks (WSNs) into agricultural areas has had a significant impact and has provided new, more complex, efficient, and structured solutions for enhancing crop production. This research reviews the role of Wireless Sensor Networks (WSNs) in monitoring the macro-nutrient content of plants. The review study focuses on identifying the types of sensors used to measure macro-nutrients, determining sensor placement within agricultural areas, implementing wireless technology for sensor communication, and selecting device transmission intervals and ratings. The study of NPK (Nitrogen, Phosphorus, Potassium) monitoring using sensor technology in precision agriculture is of high significance in efforts to improve agricultural productivity and efficiency. In addition to fostering technological innovations and precision farming solutions, in future this research aims to increase agricultural yields, particularly by enabling the cultivation of certain crops in locations different from their original ones.

Gold nanoparticles have been indicated for use in a diagnostic and/or therapeutic role in several cancer types. The use of gold nanorods (AuNRs) with a surface plasmon resonance (SPR) in the second Near-Infrared II (NIR-II) optical window promises deeper anatomical penetration through increased maximum permissible exposure and lower optical attenuation. In this study, the targeting efficiency of anti-epidermal growth factor receptor (EGFR) antibody functionalised AuNRs with an SPR at 1064 nm was evaluated in vitro. Four cell lines, KYSE-30, CAL-27, Hep-G2 and MCF-7 that either over or under expressed EGFR were used. This expression was confirmed by flow cytometry and immunofluorescence. Cytotoxicity assays showed no AuNRs toxicity to both EGFR positive and EGFR negative cell lines up to a concentrations of 19 µg/ml. Optical microscopy demonstrated a significant difference (p<0.0001) between targeted AuNRs (tAuNRs) and untargeted AuNRs (uAuNRs) in all four cancer cell lines. This study demonstrates that anti-EGFR functionalisation significantly increased the number of tAuNRs associated with each EGFR positive cancer cell. This successful targeting highlights the use of tAuNRs for molecular photoacoustic imaging or tumour treatment through plasmonic photothermal therapy.

Addressing within field spatial variability for nitrogen management to avoid over and under-use of nitrogen is crucial for optimizing crop productivity and ensuring environmental sustainability. In this study we investigated the economic, environmental and agronomic benefits of variable rate nitrogen application in potato (Solanum tuberosum). An online visible and near infrared (vis-NIR) spectroscopy sensor we utilized to predict soil moisture content (MC), pH, total organic carbon (TOC), extractable phosphorus (P), potassium (K), magnesium (Mg), and cation exchange capacity (CEC) using a partial least squares regression (PLSR) models. The crop's normalized difference vegetation Index (NDVI) from Sentinel-2 satellite images was incorporated to online measured soil data to derive fertility management zones (MZs) maps, after homogenous raster and clustering analyses. The MZs maps were categorized into high fertile (VR-H), medium-high fertile (VR-MH), medium-low fertile (VR-ML), and low fertile (VR-L) zones. A parallel strip experiment compared variable rate nitrogen (VR-N) with uniform rate (UR) treatments, adjusting nitrogen levels based on fertility zones as: 50% less for VR-H, 25% less for VR-MH, 25% more for VR-ML, and 50% more for VR-L zones compared to the UR treatment. Results showed that the VR-H zone received a 50% reduction in N fertilizer input and demonstrated a significantly higher crop yield compared to the UR treatment. This implies a potential reduction in negative environmental impact by lowering fertilizer costs while maintaining robust crop yields. In total, the VR -N treatment received an additional 1.2 Kg/ha of nitrogen input, resulting in a crop yield increase of 1.89 tons/ha. The relative gross margin for the VR-N treatment compared to the UR treatment 374.83 €/ha, indicating substantial profitability for the farmer. To further optimize environmental benefits and profitability, additional research is needed to explore site-specific application of all farm resources through precision agricultural technologies.

The monitoring of maternal and child health, using wearable devices made with wireless sensor technologies, is expected to reduce maternal and child death rates. Wireless sensor technologies have been used in wireless sensor networks to enable the acquisition of data for monitoring machines, smart cities, transportation, asset tracking, and tracking of human activity. Applications based on wireless body area network (WBAN) have been used in healthcare for measuring and monitoring of patient health and activity through integration with wearable devices. Wireless sensors used in WBAN can be cost-effective, enable remote availability, and can be integrated with electronic health record (EHR) management systems. Interoperability of WBAN sensor data with other linked data has the potential to improve health for all, including maternal and child health through the improvement of data access, data quality and healthcare access. This paper presents a survey of the state-of-the-art techniques for managing WBAN sensor data interoperability. The findings in this study will provide reliable support to enable policymakers and health care providers to take action to enhance the use of e-health to improve maternal-child health and reduce the mortality rates of women and children.

The aim of this review is to provide a survey of the recent advances and the main remaining challenges related to the ultrananocrystalline diamond (UNCD) nanowires and other nanostructures which exhibit excellent capability as the core components for many diverse novel sensing devices, due to the unique material properties and geometry advantages. The doping introduced in the gas phase during deposition promotes p-type or n-type conductivity. With the establishment of the UNCD nanofabrication techniques, more and more nanostructure based devices are being explored in measuring basic physical and chemical parameters via classic and quantum methods, as exemplified by gas sensors, ultraviolet photodetectors, piezoresistance effect based devices, biological applications, and nitrogen-vacancy color center based magnetic field quantum sensors. Highlighted finally are some of the remaining challenges and future outlook in this area.

A novel chemically cross-linked hydrogel was prepared through the utilization of the nor-bornene (Nb)-methyl tetrazine (mTz) click reaction, derived from carboxymethyl cellulose (CMC) and alginate (Alg). The hydrogel was designed to generate reactive oxygen species (ROS) from NIR-dye, indocyanine green (ICG) for a combined photothermal and photodynamic ther-apy (PTT/PDT). The cross-linking of Nb and mTz moieties occurred via an inverse elec-tron-demand Diels-Alder reaction under physiological conditions avoiding the need for a cata-lyst. The resulting hydrogels exhibited viscoelastic properties (G′ ~ 492-270 Pa) and high porosi-ty. The hydrogels were found to be injectable with tunable mechanical characteristics. The ICG encapsulated hydrogels demonstrated ROS generation ability under NIR exposure. The ROS production was investigated through DPBF assays to access photodynamic effect (with NIR irra-diation at 1-2W for 5-15 min). The temperature of the ICG-loaded hydrogels was also raised up-on the NIR irradiation to eradicate tumor cells photothermally. In vitro cytocompatibility as-sessments revealed the non-toxic nature of CMC-Nb and Alg-mTz towards HEK-293 cells. Fur-thermore, the ICG-loaded hydrogels effectively inhibited the metabolic activity of Hela cells following NIR exposure. This innovative hydrogel system holds promise for applications in combined PTT and PDT.

A recent study showed the potential of DA Perten 7200 NIR Spectrometer in detecting chlorpyrifos-methyl pesticide residue in rough, brown, and milled rice. However, this instrument is still lab-based and generally suited for point-of-sale testing in many countries. To provide a field deployable version of this technique, an existing light emitting diode (LED)-based instrument which provide discrete NIR wavelength illumination and reflectance spectra over the range of 850-1550 nm was tested. Spectra were collected from rough, brown, and milled rice at different pesticide concentrations and analysed for quantitative and qualitative measurement using partial least squares regression (PLS) and discriminant analysis (DA). Simulations for LED-based instruments were also evaluated using segments of spectra from the DA7200 to represent LED illumination. For the simulation of the existing LED-based instrument (LEDPrototype1) using their wavelengths range yielded 70.4% to 100% correct classification. Simulation of a second LED instrument, LEDPrototype2, with spectral segments selected based on significant wavelength regions from PLS regressions coefficients obtained from the DA7200 showed improved performance with R2 of 0.59 to 0.82 and correct classifications of 71.3 to 100%. An actual LED based instrument with this capability could provide a quick screening tool to determine if MRLs are exceeded.

We prepared poly(3,4-ethylenedioxythiophene) (PEDOT)-coated sulfonated polystyrene copolymer particles as efficient heat-shielding agents, which showed strong near-infrared (NIR) absorption, with high solid contents and good solution stability. The poly(styrene sulfonate -co-styrene) (P(SS-co-St)) copolymers were successfully synthesized via radical solution polymerization, and PEDOT-coated P(SS-co-St) (PEDOT:P(SS-co-St)) was synthesized via Fe⁺-catalyzed oxidative polymerization. PEDOT:P(SS-co-St) was characterized by nuclear magnetic resonance and Fourier transform infrared spectroscopies. The particle size and morphology of PEDOT:P(SS-co-St) were examined using transmission electron microscopy, dynamic light scattering, and zeta potential measurements. The maximum NIR-shielding efficiency of the film was 92.0% with 40% transmittance. The high solution stability of PEDOT:P(SS-co-St) make it an ideal candidate for heat-insulating materials that find application in semi-transparent heat-insulator-coated windows.

This work introduces a neuromorphic sensor based on force-sensing resistors (FSR) and spiking neurons for robotic systems. The proposed sensor integrates the FSR in the schematic of spiking neuron in order to make the sensor to generate spikes with frequency that depends on the applied force. The performance of the proposed sensor is evaluated for the control of a SMA-actuated ro-botic finger by monitoring the force during steady state when the finger pushes on a tweezers. For comparison purposes, we performed similar evaluation when the SNN receives input from a widely used compression load cell (CLC). The results show that the proposed FSR based neuro-morphic sensor has very good sensitivity to low forces and the function between the spiking rate and the applied force is continuous with good variation range. However, when compared to the CLC, the proposed sensor has lower linearity of the response, but it benefits from two orders of magnitude lower power consumption. These aspects imply that the neuromorphic sensor based on FSR are useful for bioinspired control of humanoid robotics representing a low power and low cost alternative the widely used sensors.

Classical and optimal control architectures for motion mechanics with fusion of noisy sensors use different algorithms and calculations to perform and control any number of physical demands, to varying degrees of accuracy, precision, and cost. Their performances are tested for the purpose of comparison through the means of a Monte Carlo simulation that simulates how different parameters might vary under noise, representing real-world imperfect sensors. We find that improvements in one figure of merit often come at a cost in the performance in the others, especially depending on the presence of noise in the system sensors. If sensor noise is negligible, open-loop optimal control performs the best. However, in the overpowering presence of sensor noise, using a control law inversion patching filter performs as the best replacement, but has significant computational strain.

This article uses machine learning analysis of wearable sensor data to explore the topic of driver differentiation. The study focuses on using detailed analyzes of data collected from wearable sensors to identify patterns that differentiate skilled drivers from inexperienced ones. On a predetermined driving route, participants experienced a variety of driving conditions, including parking, navigating cities, driving on highways and driving through residential neighborhoods. The gathered data was analyzed using machine learning techniques, yielding a classification accuracy of 94% overall. The results highlight important differences in sensor data between inexperienced and experienced drivers, providing insight into possible uses for improving safety protocols, driver education, and personalized feedback systems. The article fosters improvements in traffic safety and driver education by offering insightful information on the link between driver behavior analysis and machine learning.

This study investigates the long-term stability of the Suomi National Polar-orbiting Partnership (S-NPP) Visible Infrared Imaging Radiometer Suite (VIIRS) moderate-resolution Thermal Emissive Bands (M TEBs; M12 – M16) covering a period from February 2012 to August 2020. It also assesses inter-sensor consistency of the VIIRS M TEBs among three satellites-S-NPP, NOAA-20, and NOAA-21 over eight months spanning from March 18 to November 30, 2023. The field of interesting is limited to the ocean surface between 60°S and 60°N, specifically under clear-sky conditions. Taking radiative transfer modeling (RTM) as the transfer reference, we employed the Community Radiative Transfer Model (CRTM) to simulate VIIRS TEB brightness temperature (BTs), incorporating European Centre for Medium-range Weather Forecasts (ECMWF) reanalysis data as inputs. Our results reveal two key findings. Firstly, the reprocessed S-NPP VIIRS TEBs exhibit a robust long-term stability, as demonstrated through analyses of the observation minus background BT differences (O-B ∆BTs) between VIIRS measurements (O) and CRTM simulations (B). The drifts of the O-B BT differences are consistently less than 0.105 K/Decade across all S-NPP VIIRS M TEB bands. Notably, observations from VIIRS M14 and M16 stand out with drifts well within 0.04 K/Decade, reinforcing their exceptional reliability for climate change studies. Secondly, excellent inter-sensor consistency among these three VIIRS instruments is confirmed through the double-difference analysis method (O-O). This method relies on the O-B BT differences obtained from daily data. The mean inter-VIIRS O-O BT differences remain within 0.08 K for all M TEBs, except for M13. Even in the case of M13, the O-O BT differences between NOAA-21 and NOAA-20/S-NPP have values of 0.312 K and 0.234 K, respectively, which are comparable to the 0.2 K difference between some TEBs among VIIRS and MODIS. These disparities are primarily attributed to the significant differences in the Spectral Response Function (SRF) of NOAA-21 compared to NOAA-20 and S-NPP. Our study confirms the RTM-based TEB quality evaluation method’s versatility and effectiveness in assessing long-term sensor stability and inter-sensor consistency. The double-difference approach effectively mitigates uncertainties and biases inherent to CRTM simulations, establishing itself a robust mechanism for assessing inter-sensor consistency. In addition, we’ve observed that, except for M13, M12 always exhibits larger spatial variations of O-O BT differences with greater uncertainties compared to the other M TEBs. The influence of solar contribution through sea surface reflection on the Top of Atmosphere (TOA) radiance measurements during daytime in M12 should not be underestimated.

Copper nitride (Cu3N), a metastable semiconductor material, but with reasonably-high-stability at room temperature, is drawing a great deal of attention as a very promising next-generation, earth-abundant, thin-film solar absorber. Its non-toxicity, on the other hand, makes it a very attractive eco-friendly semiconducting material. In the present work, Cu3N thin films were grown by employing radio-frequency magnetron sputtering, at room temperature, with 50-W RF-power, and partial nitrogen pressures of 8.0 and 1.0, onto glass substrates. Thus, the influence of argon on the optical properties of the Cu3N thin films was studied, with the goal of being able to achieve a low-cost, light absorber material, with appropriate properties in order to substitute the more conventional silicon, in photovoltaic cells. Variable-angle spectroscopic ellipsometry measurements have been conducted at three angles, 50∘, 60∘, and 70∘, respectively, in order to obtain the two ellipsometric parameters psi, ψ, and delta, Δ, respectively. For the constructed optical model, the bulk planar Cu3N layer is described by a one-dimensional graded-index model, combine with the mixture of a Tauc-Lorentz oscillator and up to four Gaussian oscillators, whereas a BEMA model with 50%-air-void is adopted in order to account for the existing surface-roughness layer. In addition, the optical properties such as the energy-band gap, and refractive index and absorption coefficient, were determined in order to assess the actual capability of this material as a light absorber for solar cells. The direct and indirect band gap energies were accurately calculated, and they were found to be in the ranges of 2.14-2.21 eV and very clse to 1.50 eV, respectively.

Wireless Sensor Networks (WSN) is designed to collect information across a large number of limited battery sensor nodes. Therefore, it is important to minimize the energy consumption of each node, which leads to the extension of the network life. Our goal is to design an intelligent WSN that collects as much information as possible to process it intelligently. To achieve this goal, an agent has been migrated to each node in order to process the information and to cooperate with these neighboring nodes while Mobile Agents (MA) can be used to reduce information between nodes and send those to the base station (Sink). This work proposes to use communication architecture for wireless sensor networks based on the Multi Agent System (MAS) to ensure optimal information collection. The collaboration of these agents generates a simple message that summarizes the important information in order to transmit it by a mobile agent. To reduce the size of the MA, the nodes of the network have been grouped into sector. As for each MA, we have established an optimal itinerary, consuming a minimum amount of energy with the data aggregation efficiency in a minimum time. Successive simulations in large scale wireless sensor networks through the SINALGO simulator show the performance of our proposal, in terms of energy consumption and package delivery rate.

This paper address the development of a new technic in the sleep analysis domain. Sleep is defined as a periodic physiological state during which vigilance is suspended and reactivity to external stimulations diminished. We sleep on average between six and nine hours per night and our sleep is composed of four to six cycles of about 90-minutes each. Each of these cycles is composed of a succession of several stages of sleep, more or less deep. The analysis of sleep is usually done using a polysomnography. This examination consists of recording, among other things, electrical cerebral activity by electroencephalography (EEG), ocular movements by electrooculography (EOG) and chin muscle tone by electromyography (EMG). The recording is done mostly in a hospital, more specifically in a service for monitoring the pathologies related to sleep. The readings are then interpreted manually by an expert to generate a hypnogram, a curve showing the succession of sleep stages during the night in 30-second epochs. The proposed method is based on the follow-up of the thermal signature that makes it possible to classify the activity into three classes: "awakening", "calm sleep" and "agitated sleep". The contribution of this non-invasive method is part of the screening of sleep disorders, to be validated by a more complete analysis of the sleep. The measure provided by this new system, based on temperature monitoring (patient and ambient), aims to be integrated into the tele-medicine platform developed within the framework of the Smart-EEG project by the SYEL - SYstèmes ELectroniques team. Analysis of the data collected during the first surveys carried out with this method showed a correlation between thermal signature and activity during sleep. The advantage of this method lies in its simplicity and the possibility of carrying out measurements of activity during sleep and without direct contact with the patient at home or hospitals.

In recent years, the integration of sensors in agriculture has emerged as a pivotal catalyst for transforming conventional farming practices into precision agriculture. Sensor application is impacting the everyday objects that enhance human life. In this special issue, the main objective was to address recent advantages of sensor application in agriculture covering a wide range of topics in this field. This provides overview of diverse application of sensors in agriculture, highlighting their role in enhancing productivity, sustainability, and resource management. sensors are instrumental in monitoring various agriculture parameter such as soil condition, weather, crop health and livestock wellbeing. By collecting real-time data and providing valuable insight, sensors enable precision farming, optimize resource allocation, and minimize environmental impacts. we have to explore the key sensor types used in agriculture, their applications, benefits, and future prospects, emphasizing their crucial roles in the modernization of agriculture and global quest for food security and crop production.

This paper describes the optimal design of a miniature fiber-optic linear displacement sensor. It is characterized by its ability to measure displacements along a millimetric range with sub-micrometric resolution. The sensor consists of a triangular reflective grating and two fiber-optic probes. The measurement principle of the sensor is presented. The design of the sensor's triangular grating has been geometrically optimized by considering the step angle of the grating to enhance the sensor's resolution. The optimization method revealed a global optimum at which the highest resolution is obtained

Sensor enabled big data and Artificial Intelligence platforms has the potential to address global socio-economic trends related to the livestock production sector through advances in the digitization of precision livestock farming. The increased interest in animal welfare, the likely reduction in the number of animals in relation to population growth in the coming decade and the growing demand for animal proteins pose an acute challenge to prioritizing animal welfare on the one hand while maximizing the efficiency of production systems on the other. To stimulate a sustainable, digital, and resilient recovery of the agricultural and livestock industrial sector, there is an urgent need for testing and develop new ideas and products such as wearable sensors. By validating and demonstrating a fully functional wearable sensor prototype within an operational environment on the livestock farm that includes a miniaturized animal-borne biosensor and an artificial intelligence (AI) based data acquisition and processing platform, the unmet current needs can be fulfilled. The expected quantifiable results from wearable biosensors will demonstrate that the digitization technology can perform acceptably within the performance parameters specified by the agricultural sector and under operational conditions, to measurably improve livestock productivity and health. There is a need for a multimodal, digitized, automated biosensor and health monitoring platform containing AI algorithms for optimized stress and disease prediction in farm animals. An experimental development of non-invasive wearable and wireless physiological sensor networks that can be deployed in agricultural environments would allow for real-time extraction and integration of physiological data and display on decision support dashboards for livestock workers. By testing the effectiveness of the system in generating meaningful longitudinal data for further research into physiological and behavioral characteristics of farm animals, novel insights about animal welfare can be developed. The successful implementation of the digital wearable sensor networks would provide actionable real-time information on animal health status and can be deployed directly on the livestock farm, which will strengthen the green and digital recovery of the economy due to the significant innovation potential. Continuous monitoring of animal health and physiological functioning promotes more environmentally and socially acceptable developmental pathways. Once demonstrated, the portable animal health monitoring platform will close a critical gap in digitized livestock farming and position the agricultural industry as a frontrunner in the sector of farm animal monitoring and measurement systems. The multimodal wearable sensor-driven AI approach is expected to significantly improve the effectiveness of livestock decision support systems and the selection of resilient animals for the next generation and provide predictive data for end-users in livestock farming.

Smartwatches provide technology-based assessments in Parkinson’s disease (PD). We present results for sensor validation and disease classification via Machine Learning (ML). A comparison setup was designed with two different series of Apple smartwatches, one Nanometrics seismometer and a high-precision shaker to measure tremor-like amplitudes and frequencies. Clinical smartwatch measurements were acquired from a prospective study including 450 participants with PD, differential diagnoses (DD) and healthy participants. All participants wore two smartwatches and within a 15-min examination. Symptoms and medical history were captured on the paired smartphone. A broad range of different ML classifiers were cross-validated. Amplitude and frequency differences between smartwatches and the seismometer were under the level of clinical significance. The most advanced task of distinguishing PD vs DD was evaluated with 74,1% balanced accuracy, 86,5% precision and 90,5% recall by Multilayer Perceptrons. Deep Learning architectures significantly underperformed in all classification tasks. Smartwatches are capable of capturing subtle-tremor signs with low noise. This study provided the largest PD sample size of two-hand smartwatch measurements and our preliminary ML-evaluation shows that such a system provides powerful means for diagnosis classification and new digital biomarkers but it remains challenging for distinguishing similar disorders.

In this work, an embroidered textile moisture sensor is presented. The sensor is based on a capacitive interdigitated structure embroidered on a cotton substrate with an embroidery conductor yarn composed by 99% pure silver plated nylon yarn 140/17 dtex. In order to evaluate the sensor sensitivity, the impedance of the sensor has been measured by means of a LCR meter from 20 Hz to 20 kHz on a climatic chamber with a sweep of the relative humidity from 25% to 65% at 20 ºC. The experimental results show a clear and controllable dependence of the sensor impedance with the relative humidity. Moreover, the reproducibility of the sensor performance subject to the manufacturing process variability and washing process is also evaluated. The results show that the manufacturing variability introduce a moisture measurement error up to 4%. The washing process impact on the sensor behavior after applying the first washing cycle implies a sensitivity reduction higher than 14%. Despite these effect, the textile sensor keeps its functionality and can be reused in standard conditions. Therefore, these properties point out the usefulness of the proposed sensor to develop wearable applications on health and fitness scope including the user needs to have a life cycle longer than one-time use

IoTs and WSNs utilize their connectivity to enable solutions supporting a spectrum of industries in different and volatile environments. To effectively enhance the security and quality of service of networks, empirical research should take into account a variety of factors and be structured in a replicable manner. This will not only ensure scalability but also enable verification of conclusions, leading to more constructive outcomes. Cooja offers limited performance analysis capabilities of simulations, which are often extracted and calculated manually. In this paper, we introduce a framework and a toolkit that enable researchers to conduct structured and conclusive experiments considering different factors and metrics, experiment design to results analysis. Besides, this tool summarizes multiple network metrics and allows multiple scenarios. As proof of concept, this paper studies the flooding attacks on IoT and illustrates their impact on the network, leveraging the proposed framework and tools.

A planar microwave sensor devoted to the detection of humidity in underwear and clothes in general is proposed. The ultimate goal of the sensor is to detect the presence of liquids in fabrics, of interest to aid patients that suffer from certain pathologies, such as hyperhidrosis and enuresis. The main target in the design of the sensor, considering the envisaged application, is simplicity. Thus, the sensor operates at a single frequency, and the working principle is the variation in the mag-nitude of the transmission coefficient of a matched line loaded with an open-ended quar-ter-wavelength sensing stub resonator. The stub, which must be in contact with the so-called fabric under test (FUT), generates a notch in the transmission coefficient with a resonance frequency that depends on the humidity level of the fabric. By designing the stub with a moderately high quality factor, the variation in the resonance frequency causes a significant change in the magnitude level at the operating frequency, the resonance frequency when the sensing stub is loaded with the dry fabric, and the presence of liquid can be detected by means of an amplitude detector. A prototype device is proposed and experimentally validated.

Use of a multi-sensor approach can provide citizens a holistic insight in the air quality in their immediate surroundings and assessment of personal exposure to urban stressors. Our work, as part of the ICARUS H2020 project, which included over 600 participants from 7 European cities, discusses data fusion and harmonization on a diverse set of multi-sensor data streams to provide a comprehensive and understandable report for participants, and offers possible solutions and improvements. Harmonizing the data streams identified issues with the used devices and protocols, such as non-uniform timestamps, data gaps, difficult data retrieval from commercial devices, and coarse activity data logging. Our process of data fusion and harmonization allowed us to automate the process of generating visualizations and reports and consequently provide each participant with a detailed individualized report. Results showed that a key solution was to streamline the code and speed up the process, which necessitated certain compromises in visualizing the data. A thought-out process of data fusion and harmonization on a diverse set of multi-sensor data streams considerably improved the quality and quantity of data that a research participant receives. Though automatization accelerated the production of the reports considerably, manual structured double checks are strongly recommended.

Distributed fiber optic vibration sensors based on Φ-OTDR using Rayleigh backscattering of highly coherent light source pulses are very popular type in the area of sensors due to many attractive features, mainly due to its distributed manner of sensing, i.e. they can operate as thousands of local sensors simultaneously. The paper summarizes and describes several important modifications of the original sensor scheme to enhance its key performance parameters and to extend its application potential. A multi-fiber sensor form was proposed. Single- and two-fiber sensors were designed, constructed and tested both in the laboratory and in a real environment. Variants of two-fiber sensor utilizing optical switches for the sensor flexibility enhancement are proposed and their applications are described.

Since smart cities aim at becoming self-monitoring and self-response systems, their deployment relies on close resource monitoring through large-scale urban sensing. The subsequent gathering of massive amounts of data makes essential the development of event filtering mechanisms that enable the selection of what is relevant and trustworthy. Due to the rise of mobile event producers, location information has become a valuable filtering criterion as it not only offers extra information on the event described but also enhances trust on the producer. Implementing mechanisms that validate the quality of location information becomes then imperative. The lack of such strategies in cloud architectures compels the adoption of new communication schemes for IoT-based urban services. To serve the demand for location verification in urban event-based systems (DEBS), we have designed three different fog architectures that combine proximity and cloud communication. Moreover, we have successfully assessed their performance using network simulations with realistic urban traces.

Load balancing, energy efficiency and fault tolerance are among the most important data dissemination issues in Wireless Sensor Networks (WSNs). In order to successfully cope with the mentioned issues, two main approaches (namely, Data-centric Storage and Distributed Data Storage) have been proposed in the literature. Both approaches suffer from data loss due to memory and/or energy depletion in the storage nodes. Even though several techniques have been proposed so far to overcome the mentioned problems, the proposed solutions typically focus on one issue at a time. In this paper, we integrate the Data-centric Storage (DCS) features into Distributed Data Storage (DDS) mechanisms and present a novel approach, denoted as Collaborative Memory and Energy Management (CoMEM), to overcome both problems and bring memory and energy efficiency to the data loss mechanism of WSNs. We also propose analytical and simulation frameworks for performance evaluation. Our results show that the proposed method outperforms existing approaches in various WSN scenarios.

Spatio-temporal aspects of data lead to critical information. Sensors capture data at all scales continually so it is imperative that useful information be extracted ubiquitously and regularly. Location plays a vital part by helping understand relations between datasets. It is crucial to link developmental works with spatial attributes and current challenge is to create an open platform that manages real-time sensor data and provides critical spatial analytics atop expert domain knowledge provided in the system. That is a two-faced problem where the solution tackles not only data from multiple sources but also runs data management platform, a spatial data infrastructure(SDI) as backbone framework able to harness sensor web(SW). The paper proposes development of such a globally shared open spatial expert system(ES), SmaCiSENS, a first of a kind geo-enabled knowledge based(KB) ES for multiple fields, smarter cities to climate modeling. SmaCiSENS is integration of SW and SDI with domain KB on data and problems, ready to infer solutions. The paper describes an architecture for semantic enablement for SW, SDI; connect interfaces, functions of SDI and SW, and sensor data application program interfaces (APIs) to better manage climate modeling, geohazard, global changes, and other vital areas of attention and action.

Wireless Sensor Networks (WSNs) are being increasingly adopted in critical applications, where verifying the correct operation of sensor nodes is a major concern. Undesired events may undermine the mission of the WSNs. Hence their effects need to be properly assessed before deployment to obtain a good level of expected performance and during the operation in order to avoid dangerous unexpected results. In this paper we propose a methodology to support design and deployment of dependable WSNs by means of an event-based formal verification technique. The methodology includes a process to guide designers towards the realization of a dependable WSN and a tool ("ADVISES") to simplify its adoption. The tool allows to generate automatically formal specifications used to check correctness properties and evaluate dependability metrics at design time and at runtime. During the runtime we can check the behavior of theWSN accordingly to the results obtained at design time and we can detect sudden and unexpected failures, in order to trigger recovery procedures. The effectiveness of the methodology is shown in the context of two case studies, aiming to illustrate how the tool is helpful to drive design choices and to check the correctness properties of theWSN at runtime

Virtual validation of radar sensor models is becoming increasingly important for the safety validation of adf. Therefore, methods for quantitative comparison of radar measurements in the context of model validation need to be developed. This paper presents a novel methodology for accessing and quantifying validation measurements of radar sensor models. This method uses edf and the so-called dvm to effectively quantify deviations between distributions. By applying this metric, the study measures the consistency, reproducibility and repeatability of radar sensor measurements. Different interfaces and different levels of detail are investigated. By comparing the radar signals from real world experiments where different objects are present, valuable insights are gained into the performance of the sensor. In particular, the research extends to assessing the impact of varying rain intensities on the measurement results, providing a comprehensive understanding of the sensor’s behaviour under these conditions. This holistic approach significantly advances the evaluation of radar sensor capabilities and enables the quantification of the maximum required quality of radar simulation models.

Among the five human senses, light, sound, and force perceived by eye, ear, and skin, respectively are physical actions, and therefore can be easily measured and expressed as objective, univocal, and simple digital data with physical quantity. However, taste and odor molecules perceived by tongue and nose are chemical actions, it has been difficult to express them as objective and univocal digital data, since no reference chemicals can be defined. Therefore, while the recording, saving, transmitting to remote locations, and replaying human visual, auditory, and tactile information as digital data in digital devices has been realized (this series of data flow is defined as DX (digital transformation) in this review), the DX of human taste and odor information is not yet in the realization stage. Particularly, since there are at least 400,000 types of odor molecules and an infinite number of complex odors that are mixtures of these molecules, it has been considered extremely difficult to realize "human olfactory DX" by converting all odors perceived by the human olfaction into digital data. In this review, we discuss the current status and future prospects of the development of "human olfactory DX," which we believe can be realized by utilizing odor sensors that employ the olfactory receptors (ORs) that support human olfaction as sensing molecules (i.e., human OR sensor).

An antenna sensor is proposed to execute dual functions of antenna and sensor in the wireless sensor system, in order to reduce data loss and to increase transmission rate by omitting a certain interface. The as-made sensor was test at a center frequency of 46 MHz for measuring human finger postures using principle of dipole antenna. The antenna sensor was attached on a wearable glove. The results showed that the motion sensor can accurately identify finger angles at 0°, 20°, 40°, 60° and 80°.

How do sensor research and technologies grow over time? This paper applies the network analysis with a new computational approach to map the structure and evolution of sensor research and technologies over a 30-year time frame (1990-2020).The goal of this study is to analyze the evolution of sensor research for forecasting emerging scientific and technological trajectories. Results show that the scientific interaction within ecosystem (represented with networks) of sensor generates a co-evolution of scientific fields supporting the accelerated growth of different technological tra-jectories, such as: wireless sensors, fiber optic and optical sensors, gas sensors and biosensors. These results suggest main theoretical implications that explain the evolution of sensor research with critical aspects of innovation management to support R&D investments towards new technological trajectories having a high potential of growth.

Saudi Arabia is a prominent producers of dates, with 1.6 million tons annually. There is a need to evaluate physical properties and quality of fruits non-destructively and then be modeled and predicted throughout the storage period. The aim of the current study was to generate a quality index (Qi) and Near-infrared spectra (NIR) models non-destructively to predict properties of Barhi dates fruits including objective and sensory evaluations. The engineering properties of Barhi dates were measured and modeled with quality index (Qi) based on NIR of fresh Barhi fruits (hardness, color, TSS, pH, and sensory evaluations) and during storage in cold, ambient, and controlled at-mosphere (CA) for up to four months. The prediction of Qi is non- destructively based on NIR utilizing PLSR and ANN data analysis. The results showed that the Qi generated corresponds with high precision to the characteristics of the examined fruits through the duration of the storage period with R2 of 0.96. The NIR spectrum proves to be an efficient method to evaluate the Barhi fruits' quality index. where ANN was found to be more suitable than PLSR analysis. Thus, NIR can be utilized to accurately predict the Qi of fruits quality effectively throughout the handling, processing, transporting, storage, and retail sector supply chain.

Ankle joint flexion and extension exercises play an important role in the rehabilitation training of patients who have been injured or bedridden for a long time before and after surgery. Accurately guiding patients to perform ankle flexion and extension exercises can significantly reduce deep vein thromboembolism. Currently, most ankle rehabilitation devices focus on assisting patients with ankle flexion and extension movements, and there is a lack of devices for effectively monitoring these movements. In this study, we designed an ankle joint flexion and extension movement monitoring device based on a pressure sensor. It is composed of an STM32 microcontroller, a pressure sensor, an HX711A/D conversion chip, and an ESP8266 WiFi communication module. The value of force and effective number of ankle joint flexion and extension movements were obtained. An experimental device was designed to verify the accuracy of the system. The results showed that the device can effectively monitor and control ankle flexion and extension movements remotely, ultimately ensuring that the patient can effectively monitor and grasp the active ankle pump movement.

The reliability of Underwater Wireless Sensor Networks (UWSNs) is measured in terms of energy consumption (EC), end-to-end delay(E2E) and packet delivery ratio (PDR). The adverse effects of channel may cause data loss. Reducing delay up to possible extend improves the reliability of the network, also increasing the number of nodes in a particular network increase reliability. Besides, increasing the number of nodes improve reliability but also increase power consumption. In order to overcome these shortcomings, the two routing protocols are proposed in this paper, namely Delay and Reliability Aware Routing (DRAR) protocol and Cooperative Delay and Reliability Aware Routing (Co-DRAR) protocol for UWSNs. In DRAR protocol, network is divided into two equal regions where two sink nodes(SNs) are positioned at upper region of the network and two SNs are placed at the mid region of the network. The protocol choose the relay node based on residual energy (RE), distance and Bit Error Rate (BER). These parameters protect the data packets from corruption and also provide stable path (where nodes remain active for longer period and do not die quickly). The protocol uses single link and may get worse sometimes while changing channel circumstances. To address this problem, cooperative routing scheme is added to DRAR protocol in order to developed its enhanced version known as Co-DRAR protocol. The protocol works by allowing the destination to receive multiple copies of data packets in order to decide the quality of packets. The proposed protocols DRAR and Co-DRAR perform routing irrespective to geographical position of sensors nodes conversely to the some of conventional routing protocols that's way our propose protocol better perform than the well-known protocol i.e. Depth base routing (DBR) in terms of EC, E2E, PDR, dead nodes, packet drop ratio and number of alive nodes (ANs).

The present study reports on the fabrication and performance of ammonia sensors based on single-walled carbon nanotubes (SWCNTs) coated with gold nanoparticles (AuNPs). The sensors were subjected to controlled concentrations of ammonia at two temperatures, namely 25 oC and 140 oC, and their response was monitored through successive cycles of ammonia exposure and nitrogen purging. The results demonstrate that the sputtering-based deposition of AuNPs on SWCNTs led to the best sensor performance, characterized by a rapid increase in resistance values upon exposure to ammonia, and efficient recovery at 140 oC. By contrast, the sensor with chemically impregnated AuNPs exhibited a slower response time. Furthermore, a novel device was developed that combined MoS2-AuNPs (sputtering)-SWCNTs, and it showed improved sensor performance compared to the devices with only AuNPs. Overall, the study provides valuable insights into the fabrication and optimization of SWCNT-based ammonia sensors for various applications, especially for detecting and quantifying small amounts of ammonia (concentrations below 1 ppm).

Various efforts have been made to detect minimum value of glucose in any medium like water or body buffer solutions with high-sensitivity, accurate, and low-cost sensors in order to enhance life style. Therefore, the present study was done to investigate reliability of two-dimensional plasmonic structure by circular dichroism (CD) and ellipsometry tools in different concentrations of glucose. Our results confirmed a dependency of the CD signal on glucose concentrations and also a very good sensitivity based on the phase difference between each polarization in ellipsometry parameters with the help of an achiral plasmonic structure.