Electrifying off-grid and isolated islands in the Philippines remains one of the challenges that hinders community development. One of the solutions seen to ensure energy security, expand energy access and promote a low carbon future in this isolated islands is the use of renewable energy sources. This study wishes to determine the nearshore wave energy resource during monsoon seasons in Cuyo Island using a 40-year wave hindcast and 9-year on-site wind speed data to develop high resolution wave energy model using SWAN wave model, and assessed its annual energy production through matching with wave energy devices. Results shows that average significant wave height (Hs), peak period (Tp) and wave power density (Pd) during northeast monsoon are Hs = 1.35 m, Tp = 4.79 s and Pd = 4.05 kW/m respectively, while southwest monsoon which is sheltered by the mainland resulted to a lesser outcome, Hs = 0.52 m, Tp = 3.37 s and Pd = 0.34 kW/m. While the simulated model was observed to overestimate the wave energy resource (Bias = 0.398, RMSE = 0.54 and SI = 1.34), it has a strong relationship with the observed values (average r = 0.9). Its annual energy production is highest at Station 5, with AEPWaveBouy = 43.761 MWh, AEP-Pelamis = 216.786 MWh and AEPWave Dragon = 2462.66 MWh. At present, the minimum requirement for a wave energy development to be feasible is 5 kW/m, which in this case, Cuyo Island falls short, but with the continuous evolution of wave energy converters, applications on milder re-sources will soon materialized.

Wave buoy measurements were carried out near the north-eastern Black Sea coast at the natural reserve Utrish in 2020-2021. In total, about 11 months of data records were collected during two stages of the experiment at 600 and 1500 meters offshore and depths of 18 and 42 meters. The measured waves propagate almost exclusively from the seaward directions. Generally, the waves do not follow the local wind directions, thus, implying a mixed sea state. Nevertheless, dimensionless wave heights and periods appears to be quite close to the previously established empirical laws for the wind-driven seas. The results of the wave turbulence theory are applied for estimates of spectral energy fluxes and their correspondence to the energy flux from the turbulent wind pulsations. These estimates are consistent with today's understanding of wind-wave interaction. It is shown that the main fraction of the wind energy flux goes to the direct Kolmogorov-Zakharov cascade to high wave frequencies and then to dissipation in small scales. Less than 1% of the wind energy flux is directed to low frequency band (the so-called inverse Kolmogorov-Zakharov cascade), thus, providing wave energy growth.

Nanoporous materials, such as Metal-Organic Frameworks (MOFs), are renowned for their high selectivity as gas adsorbents due to their specific surface area, nanoporosity, and active surface chemistry. A significant challenge for their widespread application is their behavior and reduced gas uptake in wet conditions, attributed to competitive adsorption between gas and water. The current understanding of gas adsorption in wet materials is constrained by studies that utilize only small amounts of powdered porous materials (in the milligram range) within very small reactors (1-5 mL). This leaves a significant gap in knowledge about gas adsorption behaviors in larger reactors and when MOF sample sizes are increased (to the gram scale) for scaling up the process. Additionally, there is a notable dearth of experimental research in situations where MOFs are heavily saturated with water. To address these gaps, this study measures CH4 adsorption in MOFs under conditions of high moisture content, using larger samples of MOFs (in grams) and a large volume reactor. We selected commercially available MOFs, including HKUST-1, ZIF-8, MOF-303, and activated carbon. A high-pressure isotherms (at T = 274.15 K) using volumetric approach were measured to qualitatively compare the moles of gas adsorbed under both dry and wet conditions across different MOFs and weights. Experimental results show that the presence of water led to a decrease in total CH4 mmol adsorption in MOFs, with a more significant decrease observed in hydrophilic MOFs compared to hydrophobic ones. For hydrophilic MOFs, presence of crossover isotherms at crossover pressure provided evidence of water's conversion to hydrate and its positive role in enhancing total gas uptake, which varied among different hydrophilic MOFs. Oversaturated MOFs showed a larger deviation between dry and wet cases at higher pressures. The high-pressure isotherm data confirm the positive role of hydrophilic MOFs in the conversion of water to hydrate in oversaturated MOFs when MOFs sample size is large.

The study investigated farmers’ perception on pests and diseases management strategies, agricultural practices, production constraints and selection criteria of elite varieties using a survey research design. A total of 700 questionnaires were administered to smallholder farmers who were farming for household consumption, those producing for sale and household consumption and those who were mainly producing for sale because their primary goal was to produce for the market. Findings revealed that the most prevalent pests identified were whiteflies (Bemisia tabaci), grasshoppers (Zonocerus variegatus), aphids (Aphis gossypii), mealybugs (Phenacoccus manihoti), termites (Isoptera), and grasscutters (Thryonomys swinderianus). The three most common diseases of cassava limiting growth and yield with mixed infection include viral, bacterial, and fungal. The study also revealed that only 12.5% of farmers cultivated improved cassava varieties. The management practices implemented encompassed field sanitation and the application of pesticides. Lack of capital and no availability of market were the most important production and marketing constraints faced by farmers in the study area, whereas poundability and high storage root yield are the most preferred traits farmers consider in selecting a new variety. Results suggest that smallholder farmers should endeavor to undergo various developmental programs to develop themselves to increase their competitive advantage in their locality and in the local and global agricultural sectors. In addition, governments and other policy makers should strategize plans and programs that would contribute to smallholder farmers’ agriculture, community and national development.

Electricity consumption is often the hotspot of life cycle assessment (LCA) of products, industrial activities, or services. The objective of this paper is to provide a consistent, scientific, region-specific electricity-supply-based inventory of electricity generation technology for national and regional power grids. Marginal electricity generation technology is pivotal in assessing impacts related to additional consumption of electricity. China covers a large geographical area with regional supply grids; these are arguably equally or less integrated. Meanwhile, it is also a country with internal imbalances in regional energy supply and demand. Therefore, we suggest an approach to achieve a geographical subdivision of the Chinese electricity grid, corresponding to the interprovincial regional power grids, namely the North, the Northeast, the East, the Central, the Northwest, and the Southwest China Grids, and the China Southern Power Grid. The approach combines information from the Chinese national plans on for capacity changes in both production and distribution grids, and knowledge of resource availability. The results show that nationally, marginal technology is coal-fired electricity generation, which is the same scenario in the North and Northwest China Grid. In the Northeast, East, and Central China Grid, nuclear power gradually replaces coal-fired electricity and becomes the marginal technology. In the Southwest China Grid and the China Southern Power Grid, the marginal electricity is hydropower towards 2030.

Promoting the sustainable development of resource-based cities is of great significance to the ecological protection and high-quality development of the Yellow River Basin. Combining the environmental status and economic development, we objectively evaluate the ecological safety level of resource-based cities in the Yellow River Basin, compare and analysis the main factors affecting the ecological safety of different resource-based cities, and formulate precise and differentiated ecological safety protection measures in river basins to achieve high-quality development. Taking the Yellow River Basin as an example, this paper analyses the ecological level of the Yellow River Basin based on the theory of sustainable development, calculates the ecological safety level of 30 resource-based cities in the Yellow River Basin from 2006 to 2020 by TOPSIS model, and makes convergence analysis by classification. Through the DID empirical test of sustainable development planning policy on ecological safety factors, distinguish the development characteristics of different resource-based cities. The results show that: (1) the ecological safety level of resource-based cities in the Yellow River Basin is generally developing well, and there are differences among different types of resource-based cities; (2) the kinetic energy of sustainable development of resource-based cities in the Yellow River Basin is mainly industrial transformation, and the power of science and technology is insufficient; (3) local governments pay limited attention to environmental protection, and the sustainable development planning of resource-based cities in 2013 mainly promotes the adjustment of industrial structure of resource-based cities.

The Upper Hunter Valley is a major coal mining area in New South Wales (NSW), Australia. Due to the ongoing increase of mining activities, PM10 (air-borne particle with an aerodynamic diameter less than 10 micrometres) pollution has become a major air quality concern in local communities. The early part of this study identified two air quality subregions in the valley. This paper aims to provide a holistic summarisation of the relationships between elevated PM10 pollution in two subregions and the local- and synoptic-scale meteorological conditions for spring and summer, when PM10 pollution is relatively high. A catalogue of twelve synoptic types and a set of six local meteorological patterns have been quantitatively derived and linked to each other using the self-organising map (SOM) technique. The complex meteorology-air pollution relationships have been visualised/interpretated on the SOM planes for two representative locations. It was found that the influence of local meteorological patterns differed significantly for mean PM10 levels vs the occurrence of elevated pollution events and between air quality subregions. In contrast, synoptic types showed generally similar relationships with mean vs elevated PM10 pollution in the valley. Two local meteorological patterns, the hot-dry-northwesterly wind conditions and the hot-dry-calm conditions, were found most PM10 pollution conducive in the valley when combined with a set of synoptic counterparts. These synoptic types are featured with the influence of eastward migrating continental high pressure system and westerly troughs, or a ridge extending northwest towards coastal northern NSW or southern Queensland from the Tasman Sea. The method and results can be used in air quality research for other locations of NSW, or similar regions elsewhere.

Rhododendron chrysanthum Pall., live in Changbai Mountain being exposed to chilling temperature, high light intensities and water scarcity condition. To adapt to the harsh environment, the cold resistance mechanisms of R. chrysanthum have been successfully evolved in the long-term adaptive process. In our present work, the methods of proteomics combined with physiological and biochemical analyses were used to investigate the effects of cold stress on the photosynthesis and antioxidant system of Rhododendron chrysanthum Pall. and the molecular mechanisms involved in cold resistance of plants. A total of 153 photosynthesis related proteins were identified in present work, of which 7 proteins including Rubisco large subunit (rbcL) were up-regulated in experiment group (EG) compared with control group (CG). Simultaneously, four chlorophyll fluorescence parameters were measured in present study. The results showed that the maximum photochemical efficiency of photosystem II (Fv/Fm), actual quantum yield of PSII (Y(II)) and photochemical quenching (qP) were significantly higher in EG, whereas the non-photochemical quenching (NPQ) was notably decreased. Cold stress could lead to a significant reduction in electron transport rate (ETR) accompanied with an increase in excitation pressure (1-qP). The abundance of PetE which involved in the plants photosynthetic electron transfer was also significantly influenced by cold stress. Moreover, the up-regulated expressions and higher levels of enzymatic activities of Glutathione peroxidase (GPX) and Ascorbate peroxidases (APXs) were detected in EG. All these changes which can help plants to survive in low temperature are considered as the crucial parts of cold tolerance mechanisms. These results revealed that photosynthesis and redox adjustment play significant roles in the defense of cold-induced damage.

The study addresses the urgent environmental issue of climate change, focusing specifically on the role of local food, which is produced and consumed locally, helps reduce carbon emissions by eliminating the need for long-distance transportation. Through quantitative analysis, this study elucidates the potential benefits in environmental impact achieved through the consumption of local food: the significant reduction in carbon emissions. Specifically, the consumption of local food is found to yield an annual decrease of 2,421,296 tCO2 emissions, representing 2.5% of South Korea’s total greenhouse gas emissions from the transportation sector. This reduction further translates into an estimated economic value of USD 54.23 million (KRW 70.5 billion). This study underscores the potential of local food consumption as a tangible strategy to overcome environmental problems. Moreover, its academic contribution lies in its comprehensive analysis of the economic and empirical impacts of local food consumption on environment. Moving forward, we propose policies such as supporting local food distribution networks, providing public education on local food, fostering the local food industry, and providing incentives to revitalize local food consumption.

Background. The Stanford Health Assessment Questionnaire-Disability Index (HAQ) is widely used to measure functional ability in persons with Rheumatoid Arthritis (RA). The instrument was developed with limited involvement from persons with RA, and their perception of the instrument has not been studied in depth. The aim of this study was to explore how persons with RA experience the use of the HAQ in care. Methods. Forty persons with RA were purposefully recruited to participate in semi-structured interviews. The interviews were then analyzed qualitatively using thematic analysis. Results. The participants questioned the relevance of the HAQ but nevertheless experienced that the instrument had a profound effect on their understanding of health and how care is delivered. The analysis resulted in three themes: Problems with individual items, meaning of the summative score, and effects on care and health perceptions. Conclusions. To make the HAQ relevant to persons with RA, it needs to be revised or to include an option to select items most meaningful to the respondent. To ensure relevance, the HAQ update should preferably be co-created by researchers, clinicians and persons with RA.

This paper presents a review on numerical and experimental methods to predict fracture of ad-vanced high strength steels (AHSS). AHSS are widely processed through sheet metal forming processes. Although being an excellent choice when lightweight, high strength and ductility are critical factors, their multi-phase microstructure accentuates forming challenges. To accurately model forming behavior, necking based failure criteria as well as direct fracture models require improvements. As a necking based failure model, the conventional forming limit diagram/curve (FLD/FLC) presents limitations such as in estimating direct fracture (surface cracks, edge cracks, shear cracks), as well as deformation histories under nonlinear strain paths. Thus, significant re-search efforts are being made towards the needs of advanced fracture constitutive models capa-ble of predicting fracture scenarios without necking, more frequently observed in the realm of AHSS. Scientific community research is divided into several directions aiming at improving the forming and fracture behavior accuracy of parts subjected to sheet metal forming operations. In this review paper, a comprehensive overview on ductile fracture modeling is presented. Firstly, the FLD/FLC limitations modeling fracture behavior in sheet metal forming operations are stud-ied. Followed by the recent trends in constitutive material modeling. Afterwards, material char-acterization methods advancements to cover a broad range of stress states are comprised. Final-ly, damage and fracture models predicting failure in AHSS are investigated. This review paper supplies relevant information on the current issues the sheet metal forming community is chal-lenged with due to the trend towards AHSS employment in the automotive industry.

The COVID-19 pandemic over the past years has shown a great need for rapid, low-cost and on-site detection of severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2). In this paper, an aptamer-based colloidal gold nanoparticle lateral flow test strip was well developed to realize the visual detection of wild type SARS-CoV-2 spike protein (SP) and multiple variants. Under the optimal reaction conditions, a low detection limit of SARS-CoV-2 S protein of 0.68 nM was acquired, and the actual detection recovery was 83.3% to 108.8% for real world samples. This suggests a potential tool for the prompt detection of SARS-CoV-2 with good sensitivity and accuracy, and a new method for the development of alternative antibody test strips for the detection of other viral targets.

To conduct high-precision and high-resolution numerical simulation of complex flow structures in turbomachinery, a high-order finite volume weighted essentially non-oscillatory (WENO) scheme for the large eddy simulation (LES) is improved and embedded into the three-dimensional viscous unsteady CFD solver NUAA-Turbo. Firstly, the spectral characteristics and unsteady convergence of the improved WENO scheme are studied. Compared with the classical WENO scheme, the improved WENO scheme has better dissipation and dispersion characteristics and faster convergence speed. Then, the coefficient CW of the Wall-Adapting Local Eddy-viscosity (WALE) model is calibrated by decaying homogeneous isotropic turbulence (DHIT) test case. Finally, the scheme is applied to conduct high-precision LES calculations of turbulent boundary layer flow, supersonic compression corner flow, and low-pressure turbine cascade separation flow. The numerical simulation results show that this WENO scheme has excellent shock wave capture ability and turbulence resolution and can capture more flow field details with less mesh size, greatly reducing the computational cost and laying a foundation for large-scale engineering application of LES.

Intermetallic compounds are increasingly being expected to utilize in tribological environments, but to date the works are hindered by insufficient ductility at low and medium temperature. This paper presents a novel multiphase intermetallic alloy with the chemical composition of Mo-40Ni-13Si (at.%). Microstructure characterization reveals that a certain amount of ductile Mo phases formed during the solidification process of ternary Mo-Ni-Si alloy melt, which is undoubtedly beneficial to the ductility improvement of intermetallic alloy. Tribological properties of the designed alloy, including wear resistance, friction coefficient and metallic tribological compatibility, were evaluated under dry sliding wear test conditions at room temperature. Results suggested that the multiphase alloy possesses an excellent property for room-temperature wear applications, which is attributed to the unique microstructural features and thereby good combination in hardness and ductility. The corresponding wear mechanism is also reported by observing the worn surface, subsurface and wear debris of alloy, which to be found is soft abrasive wear.

Bridges enable communications and transportation of goods nationally and internationally, underpinning economic and social activities, thus they are pylons of our prosperity and mobility. Bridges worldwide are constantly subjected to physical wear, ageing, deterioration, hazards, environmental influences, and increased loading. Loss of performance and functionality of bridge structures would have a crucial impact on overall infrastructural resilience and would cause significant negative economic and social consequences. Monitoring their behaviour for different loading conditions relies on accurate estimations of the stress-strain state of various critical components and remaining capacities. These activities are of high importance for better planning lifespan prolongation, that is the extension of their service life and prevention of unforeseen collapses, in line with sustainability principles of well-informed maintenance. In many cases, access to the structure is limited or even impossible, which causes the need for the deployment of remote and contactless methods. One such innovative technique, which has recently attracted attention in scientific and practical applications is the digital image correlation (DIC). DIC is a contactless approach applicable for long-term measurements, which enables obtaining the full field of strains and deformations. Although the DIC approach has been widely used in world engineering practice for monitoring bridges and has proved to be a reliable and accurate method, there is a lack of systematic integral review on previous practical applications, revealing limitations and perspectives. This is the main motivation and novelty of this study, which will describe selected case studies, in which DIC was used on real full-scale bridge structures and propose improvements for the method.

For the last two decades, an increasing demand for low-cost adsorbents for drinking water treatment has been challenged in the rural areas of developing countries that have problems with arsenic (As) contamination. In this work, spent bleaching earth (SBE), a residual material that is formed during the process of refining vegetable oil, has been utilized to prepare the new magnetic adsorbent Fe-SBE/C by modifying its surface area through calcination and co-precipitation with iron. The experimental results demonstrate that Fe-SBE/C exhibits a substantial adsorption capacity towards both arsenite (As(III)) and arsenate (As(V)). Optimal pH conditions were found to be pH 10 for As(III) and pH 3 for As(V), resulting in adsorption percentages of 76.7% and 94.1%, respectively. Other experimental parameters such as calcination conditions, adsorbent dosage, iron-loading ratio, and the presence of co-existing ions were thoroughly investigated. The kinetic study revealed that the adsorption processes follow the Elovich and intraparticle diffusion models, suggesting a combined adsorption mechanism of boundary layer control and chemisorption. Furthermore, the isotherm followed the Langmuir model with a maximum adsorption capacity of 202.61 μg g-1 for As(III) and 187.61 μg g-1 for As(V). Through thermodynamic analysis and reinforcement by activation energy data, this research validates that the observed adsorption process is indicative through chemisorption. The regeneration study revealed the potential for multiple cycles of arsenic removal, highlighting the practical applicability of Fe-SBE/C in environmental contexts. In conclusion, the findings of this study underscore the efficacy of Fe-SBE/C in arsenic removal and present it as a promising and environmentally friendly solution for mitigating arsenic pollution.

The oscillating heat pipe (OHP) is a new member in the family of heat pipes, and it has great potential applications in energy conservation. However, the fluid flow and heat transfer in the OHP as well as the fundamental effects of inner diameter on them have not been fully understood, which are essential to the design and optimization of the OHP in real applications. Therefore, by combining the high-speed visualization method and infrared thermal imaging technique, the fluid flow and thermal performance in the OHPs with inner diameters of 1, 2 and 3 mm are presented and analyzed. The results indicate that three fluid flow motions, including small oscillation, bulk oscillation and circulation, coexist or, respectively, exist alone with the increasing heating load under different inner diameters, with three flow patterns occurring in the OHPs, viz. bubbly flow, slug flow and annular flow. These fluid flow motions are closely correlated with the heat and mass transfer performance in the OHPs, which can be reflected by the characteristics of infrared thermal images of condensers. The decrease in the inner diameter increases the frictional flow resistance and capillary instability while restricting the nucleate boiling in OHPs, which leads to a smaller proportion of bubbly flow, a larger proportion of short slug flow, a poorer thermal performance, and easier dry-out of working fluid. In addition, when compared with the 2 mm OHP, the increasing role of gravity induces the thermosyphon effect and weakens the 'bubble pumping' action, which results in a little smaller and bigger thermal resistances of 3 mm OHP under small and bulk oscillation of working fluid, respectively.

Dearth of information on extent of genetic variability in cassava limits the genetic improvement of cassava in Sierra Leone. This study aimed at assessing the genetic variability and relationships within 103 cassava genotypes using agro-morphological and culinary markers. A field trial was conducted in the School of Agriculture and Food Sciences research site. The experiment was laid in an augmented randomized block design. Morphological classification based on qualitative and quantitative traits categorized the germplasm into three different groups. A total of ten principal components (PCs) in the qualitative and six PCs in the quantitative trait sets accounted for 66.74% and 67.27% of the total genetic variation, respectively. Traits with significantly strong and positive correlations included presence of fruit (PFRT) and presence of seed (PSE)(r = 0.86***),root yield per plant (RYPP) and number of storage root (NSR) (r = 0.76***), RYPP and number of commercial root (NCR) (r = 0.68***), length of leaf lobe (LLL) and width of leaf lobe (WLL) (r = 0.66***),and between NSR and NCR (0.84***). Cooking time, cooking percentage, texture, mealiness, taste and aroma varied widely among the accessions. Findings established that the cassava germplasm possess useful genetic variability that could be exploited through selection for short term release programme, genetic conservation of valuable germplasm and genetic improvement of the crop.

The Circular Bioeconomy (CBE) combines the concepts of bioeconomy and circular economy. As an alternative concept to the current fossil-based, linear economy, it de-scribes an economy based on the efficient valorization of biomass. It is regional in nature and aims to improve sustainability. An analysis of the transition process, by identifying its success criteria and assessing its impacts through the modelling of technology-specific scenarios is necessary to ensure that CBE concepts are sustainable. However, a compre-hensive consideration of regional influences on both is lacking. Based on extensive literature research and an expert survey, we (i) present a compre-hensive catalog of CBE success criteria and discuss their region-specific character and (ii) develop a methodology based on evaluation matrices that enable to match CBE technolo-gies with regions. The matrices support the evaluation of technological and regional characteristics influencing the successful CBE implementation. The results show that the success criteria "biomass resources", "technological", and "social" are perceived as highly important, and that most of the success criteria are both region- and technology-specific, highlighting the relevance of developing matrices to match them. We describe such matrices indicatively for the two broadest and most im-portant success criteria clusters “social acceptance” and “biomass supply chain”. With this, we substantiate the regional nature of CBE and raise the awareness on the importance of considering regional conditions in CBE transition processes. Furthermore, we provide practical guidance on how regional conditions can be reflected in the selection of technologies, e.g. in regional CBE technology scenarios.

The wave energy converter (WEC) technology constantly develops new designs and models. To encourage its development within the energy sector, research is required to improve current designs and create durable and effective devices. However, it is also crucial to investigate the suitability of a WEC to a site-specific sea condition as this can impact its optimal power absorption and constructability. This study evaluates and compares the efficiency of a heaving buoy with varied geometries in one of the most energetic places along the Mexican coast. A statistical analysis of the wave climate on the coast of Ensenada during the last 42 years is performed to define the conditions to which the device is subjected. The location of the WEC in shallow waters is chosen using a computational model which solves the modified mild slope equation in its elliptic shape. The heaving buoy floater is studied using three distinct geometries: a semi-sphere, a cylinder, and a proposed rounded semi-rectangle. The hydrodynamic response of the three geometries is then analysed in the frequency and time domain using ANSYS AQWA. The hydrodynamic study involves the assessment of the floating body dynamics, exerted forces, the power absorbed as well as the suitability of the proposed power take-off (PTO) system. Findings reveal that the proposed geometry absorbs the most energy, with an annual power of 135.11 MW, and that the transmission PTO design is appropriate for this type of technology.

Despite being stored at 113 K and atmospheric pressure, LNG cold potential is not exploited to reduce green ships’ energy needs. An innovative system based on three Organic Ranking Cycles integrated into the regasification equipment is proposed to produce additional power and recover cooling energy from condensers. A first-law analysis identified ethylene and ethane as suitable working fluids for the first and the second ORC making available freshwater and ice. Propane, ammonia and propylene could be arbitrarily employed in the third ORC for air-conditioning. An environmental analysis that combines exergy efficiency, ecological indices and hazard aspects for marine environment and ship’s passengers, indicated propylene as safer and more environmentally friendly. The exergy analysis confirms more than 20% of the LNG potential can be recovered from every cycle to produce a net clean power of 76 kW, whereas 270 kW can be saved by recovering condensers' cooling power to satisfy some ship needs. Assuming the sailing mode, a limitation of 162 kg in LNG consumptions was determined, avoiding the emission of 1584 kg of CO2 per day. Marine thermal pollution is reduced by 3.5 times by recovering the working fluids' condensation heat for the LNG pre-heating.

This work presents an innovative application of optimal control theory to the strategic scheduling of battery storage in the day-ahead electricity market, with a focus on enhancing profitability while factoring in battery degradation. The study incorporates in the optimisation framework the cost of battery capacity degradation, the effects of capacity degradation and internal resistance degradation into dynamics. We employ a continuous-time representation of the dynamics, in contrast with many other studies that use a discrete-time approximation with rather coarse intervals. We adopt an equivalent circuit model coupled with empirical degradation parameters to simulate a battery cell’s behaviour and degradation mechanisms with good support from experimental data. Utilising direct collocation methods with mesh refinement allows for precise numerical solutions to the complex, nonlinear dynamics involved. Through a detailed case study of Belgium’s day-ahead electricity market, we determine the optimal charging and discharging schedules under varying objectives: maximizing net revenues, profits considering capacity degradation, and profits considering both capacity degradation and internal resistance increase due to degradation. The results demonstrate the viability of our approach and underscore the significance of integrating degradation costs into the market strategy for battery operators, alongside its effects on the battery’s dynamic behaviour. Our methodology extends previous work by offering a more comprehensive model that empirically captures the intricacies of battery degradation, including a fine and adaptive time domain representation, focusing on the day-ahead market, and utilising accurate direct methods for optimal control. The paper concludes with insights into the potential of optimal control applications in energy markets and suggestions for future research avenues.

The enormous growth in the penetration of electric vehicles (EVs), has laid the path to advancements in the charging infrastructure. Connectivity between charging stations is an essential prerequisite for future EV adoption to alleviate users’ “range anxiety”. The existing charging stations fail to adopt power provision allocation and scheduling management. To improve the existing charging infrastructure data based on real-time information and availability of reserves at charging stations could be uploaded to the users to help them locate the nearest charging station for an EV. This research article focuses on an a interactive user application developed through SQL and PHP platform to allocate the charging slots based on estimated battery parameters, which uses data communication with charging stations to receive the slot availability information. The proposed server-based real-time forecast charging infrastructure avoids waiting times and its scheduling management efficiently prevents the EV from halting on road due to battery drain out. The proposed model is implemented using a low-cost microcontroller and the system etiquette tested.

Gene regulation is vital for cellular function and homeostasis, involving diverse mechanisms controlling specific gene products and contributing to tissue-specific gene expression. Dysregulation leads to diseases, emphasizing the need for understanding these mechanisms. Non-coding regions, notably enhancers and super-enhancers (SEs), act as crucial gene regulators, orchestrating transcriptional activity via transcription factors (TFs). SEs, with high activity, are pivotal in cell identity and disease progression. Current computational approaches focus on individual regulators like TFs and miRNAs, neglecting SE interactions. We emphasize incorporating SEs into models to enhance understanding. Experimental studies have recently linked miRNAs and TFs to SEs. Chromatin immunoprecipitation followed by sequencing (ChIP-Seq) provides valuable SE information. In this review, we categorize computational methods leveraging TF and miRNA data into three areas and explore challenges integrating enhancers/SEs. These include unraveling indirect regulatory networks, identifying network motifs, and enriching pathway identification by dissecting gene regulators, including SEs. We hypothesize that addressing these challenges will enhance our understanding of gene regulation, aiding in identifying therapeutic targets and disease biomarkers. We believe that understanding the role of ChIP-Seq data in predicting the effect of miRNA on gene regulation is crucial to construct statistical/computational model that would tackle these challenges.

Many types of banana (Musa spp.)—one of the most economically important horticultural crops—exist, and their ploidy (diploid, triploid, and tetraploid, usually) and genome types (containing A or/and B genome in most cases) differ. At present, observation and genome type detection are commonly used to identify banana germplasm resources. However, the former is tedious, while the latter cannot distinguish categories below genome types. It is therefore urgent that a simple and effective method for identifying banana germplasm resources is established. We sequenced and analyzed the ribosomal DNA internal transcribed spacer (ITS) sequences of 62 banana germplasm and found that the sequencing peaks, especially the 20 bp region near the 420 bp position (referred to as the “420 bp region”), exhibited relatively recognizable and repeatable polymorphism characteristics. Using the “420 bp region” as a marker, we were able to quickly distinguish bananas belonging to different genome type groups (comprising the AA, AB, AAA, ABB, AAB, ABBB, AAAB, and AAAA groups) or different subgroups in the same genome type group (for example, the Cavendish, Gros Michel, Red, Lakatan, and Ibota Bota subgroups in the AAA group; and the Pisang Raja, Plantain, Pome and Silk subgroups in the AAB group). Moreover, it appeared that Sanger sequencing of ITS could be used for identifying banana hybrid offspring. These results demonstrated that the banana ITS region contains rich genetic information that is useful for genotyping. In general, ITS sequencing simplifies the classification of banana germplasm resources and has potential application in several areas of Musa improvement.

Off-grid electrification planning increasingly recognizes the importance of productive use of electricity (PUE) to promote community value creation and (financial) project sustainability. To ensure a sustainable and efficient integration in the community and energy system, PUE assets must carefully be evaluated to match both the community needs and the residential electricity demand patterns. We propose a novel methodology interlinking qualitative interviews, statistical analysis, and energy system modelling to optimize decision-making for PUE integration in off-grid energy systems in rural Madagascar by aligning relevant PUE effectively with anticipated residential electricity demand patterns based on socio-economic determinants of the community. We find that a possible contribution of the PUE to reducing the electricity costs depends signifi-cantly on three factors: 1. the residential electricity consumption patterns that are influenced by the socio-economic composition of the community, 2. the degree of flexibility of i) PUE assets and ii) operational preferences of the PUE user, and 3. the capacity of community members to finance and operate PUE assets. Our study demonstrates that significant cost reductions for PUE-integrated off-grid energy systems can be achieved by applying our proposed methodology. When matching PUE and residential consumption patterns, the integration of PUE assets in residential community energy system can reduce the financial risk of operators, provided the PUE enterprise operates reliably and sustainably. We highlight that the consideration of local value chains and co-creation approaches are essential to ensure the energy system is addressing the community’s needs, creates value for the community, enhances the project´s financial sustainability, and is achieving the overall objectives of decentralized energy system planning.

Volcanic activity essentially consists of the transfer of heat from the Earth’ interior to the surface. The precise signature of this heat transfer relates directly to the processes underway at and within a particular volcano and this can be observed, at a safe distance, remotely, using infrared sensors that are present on Earth-orbiting satellites. For over 50 years, scientists have perfected this art using sensors intended for other purposes, and they are now in a position to determine the particular sort of activity that characterizes different volcanoes. This review will describe the theoretical basis of the discipline and then discuss the sensors available for the task and the history of their use. Challenges and opportunities for future development in the discipline are then discussed.

The Upper Hunter Valley is a major coal mining area containing approximately 40% of the currently identified total coal reserves in New South Wales (NSW), Australia. Due to the ongoing increase of mining activities, PM10 (air-borne particle with an aerodynamic diameter less than 10 micrometres) pollution has become a major air quality concern in local communities. This paper summarises the spatial and temporal variability modes of PM10 pollution in the region, based on long-term multi-site monitoring data and the application of the rotated principal component analysis (RPCA) and wavelet analysis techniques. RPCA identified two distinct air quality clusters/subregions in the valley, one in the west/northwest, the other in the southeast. Wavelet analysis revealed the annual cycle to be most persistent temporal mode of PM10 variability in both subregions, with intermittent signals observed at time scales of around 120, 30~90 and under 30 days. How these variation modes are related to the effects of local PM10 emissions and the influence of meteorology at different time scales deserves further attention in future work. The findings will be used in air quality reporting and forecasting in NSW. The methodology and results can also be useful for air quality research in similar regions elsewhere.

Gas and power networks are tightly coupled and interact with each other due to physically interconnected facilities. In an integrated gas and power network, a contingency observed in one system may cause iterative cascading failures, resulting in network wide disruptions. Therefore, understanding the impacts of the interactions in both systems is crucial for governments, system operators, regulators and operational planners, particularly, to ensure security of supply for the overall energy system. Although simulation has been widely used in the assessment of gas systems as well as power systems, there is a significant gap in simulation models that are able to address the coupling of both systems. In this paper, a simulation framework that models and simulates the gas and power network in an integrated manner is proposed. The framework consist of a transient model for the gas system and a steady state model for the power system based on AC-Optimal Power Flow. The gas and power system model are coupled through an interface which uses the coupling equations to establish the data exchange and coordination between the individual models. The bidirectional interlink between both systems considered in this studies are the fuel gas offtake of gas fired power plants for power generation and the power supply to LNG terminals and electric drivers installed in gas compressor stations and underground gas storage facilities. The simulation framework is implemented into an innovative simulation tool named SAInt (Scenario Analysis Interface for Energy Systems) and the capabilities of the tool are demonstrated by performing a contingency analysis for a real world example. Results indicate how a disruption triggered in one system propagates to the other system and affects the operation of critical facilities. In addition, the studies show the importance of using transient gas models for security of supply studies instead of successions of steady state models, where the time evolution of the line pack is not captured correctly.

Microwave technology has a potential application in the extraction of zinc from sulphide ores, knowledge of the dielectric properties of these ores plays a major role in the microwave design and simulation for any process. The dielectric properties of zinc sulfide concentrate for two different apparent densities—1.54 and 1.63 g/cm³—have been measured by using the resonance cavity perturbation technique at 915 and 2450 MHz during the roasting process for the temperature ranging from room temperature to 850 °C. The variations of dielectric constant, the dielectric loss factor, the dielectric loss tangent and the penetration depth with the temperature, frequency and apparent density have been investigated numerically. The results indicate that the dielectric constant increases as the temperature increases and temperature has a pivotal effect on the dielectric constant, while the dielectric loss factor has a complicated change and all of the temperature, frequency and apparent density have a significant impact to dielectric loss factor. Zinc sulfide concentrate is high loss material from 450 to 800 °C on the basis of theoretical analyses of dielectric loss tangent and penetration depth, its ability of absorbing microwave energy would be enhanced by increasing the apparent density as well. The experimental results also have proved that zinc sulfide concentrate is easy to be heated by microwave energy from 450 to 800 °C. In addition, the experimental date of dielectric constant and loss factor can be fitted perfectly by Boltzmann model and Gauss model, respectively.

The research paper provides a mathematical framework for understanding phase shift in wave phenomena, bridging theoretical foundations with real-world applications. It emphasizes the importance of phase shift in physics and engineering, particularly in fields like telecommunications and acoustics. Key equations are introduced to explain phase angle, time delay, frequency, and wavelength relationships. The study also introduces the concept of time distortion due to a 1° phase shift, crucial for precise time measurements in precision instruments. The research also addresses infinitesimal wave energy loss related to phase shift, enriching our understanding of wave behavior, and impacting scientific and engineering disciplines.

(1) Background: A simple approach to map irrigated landcover has been introduced by using measures derived from optical spectral range as an alternative to thermal range. It has been demonstrated that substituting surface temperature (Ts, ‘thermal approach’) with SWIR transformed reflectance (STR, ‘optical approach’) to detect surface moisture is feasible with comparable results. (2) Methods: Using an iterative thresholding procedure to minimize within-class variance, the bilevel segmentation of variables derived from Landsat-8 representing surface moisture and vegetation cover was achieved for the 2020-21 summer for a key irrigation district in Australia. (3) Results: The results of irrigated landcover by optical approach found to be comparable with those by thermal approach. The classification accuracy was assessed using water delivery records at farm level. Though the overall accuracy is high in both cases, the optical approach (97.6%) performed slightly better than the thermal approach (93.9%). (4) Conclusions: The feasibility of using STR to map irrigated landcover has been confirmed by a high-level overall accuracy assessment. This has broader implications in terms of irrigated landcover assessment, as the use of satellite imagery in these applications may not necessarily be limited to microwave or thermal sensors.

The development of accurate dynamic battery pack models for electric vehicles (EVs) is critical for the ongoing electrification of the global automotive vehicle fleet, since these serve as a key element in the energy performance of an EV powertrain system. The Equivalent Circuit Model (ECM) technique at the cell level is commonly employed for this purpose, combining accuracy and efficiency in the representation of battery operation within the broader powertrain system. In this study, a second-order ECM model of a battery cell is being developed using Modelica, an equation-based modeling language. Parameter lookup tables at multiple levels of state of charge (SoC), extracted from Li-ion battery cells with 4 different commonly used cathode materials, have been utilized. This approach allows for a representation of the battery systems that are used in a wide range of commercial EV applications. To verify the model, an integrated EV model is developed and simulation results of the FTP75 driving cycle have been compared against an equivalent application in MATLAB Simulink. The findings demonstrate a close match between the results obtained from both software across different system points. Specifically, the maximum deviation of SoC is limited to 0.08% and the maximum value of relative voltage deviation is 1.4%. The verified model enables the exploration of multiple possible architecture configurations of EV powertrains with Modelica.

In the drive towards environmental restoration and sustainable energy solutions, effective utilization and management of agricultural crop residues are vital to mitigate greenhouse gas (GHG) emissions and waste accumulation. Converting biogenic wastes into biofuels and bioproducts has the potential to tackle the energy crisis and contribute to environmental remediation. In this investigation, teff husk, primarily generated in Ethiopia during teff production within the agro-industrial sector, is used as the feedstock for the slow pyrolysis process. In Ethiopia, it is estimated that over 1.75 million tons of teff husk are generated annually, with a significant portion being incinerated in the fields, resulting in substantial environmental pollution. This study focuses on assessing teff husk as a potential material for slow pyrolysis, a crucial stage in biochar production, to tap into its biochar-producing potential. To determine the composition of the biomass, the teff-husk was initially analyzed by thermogravimetry. The significant presence of fixed carbon indicates that teff husk is a viable candidate for pyrolytic conversion into biochar particles. The process of slow pyrolysis took place at three varied temperatures—specifically, at 400, 450, and 500 °C. Process parameters of slow pyrolysis such as reaction time, temperature, and heating rate were enhanced to obtain maximum biochar yields. The highest biochar yield of 43.4 wt% was recorded at optimized reaction time, temperature, and heating rate of 120 min, 400 °C, and 4.2 °C/min, respectively. Furthermore, biochar's physicochemical, SEM-EDX, FTIR, and TGA characterization were performed. The thermal stability and carbon content of biochar were found to rise at higher temperatures. Unlike fuel recovery, the results suggest that teff-husk can be used as a feedstock for biochar production.

The article delves into the crucial realm of compressing hydrogen in its gaseous state, a pivotal process for enhancing its viability in both civil and industrial sectors. The study initiates by providing a concise overview and comparison of diverse hydrogen storage methodologies, laying the groundwork with an in-depth analysis of hydrogen's thermophysical properties. It scrutinizes plausible configurations for hydrogen compression, aiming to strike a delicate balance between energy consumption, predominantly derived from the fuel itself, and the requisite number of compression stages. Notably, to render hydrogen storage competitive in terms of volume, pressures of at least 350 bar are deemed essential, albeit at an energy cost amounting to approximately 10% of the fuel's calorific value. Multi-stage compression emerges as a crucial strategy, not solely for energy efficiency, but also to curtail temperature rise, with an upper limit set at 200°C. This nuanced approach is underlined by the exploration of compression levels commonly cited in the literature, particularly 350 bar and 700 bar. Ultimately, the study advocates for a three-stage compression system as a pragmatic compromise, capable of achieving high-pressure solutions while keeping compression work below 10 MJ/kg, a threshold indicative of sustainable energy utilization.

This paper analyzes and compares models for predicting average magnet losses in interior permanent-magnet motors with fractional-slot concentrated windings due to harmonics in the armature reaction (assuming sinusoidal phase currents). Particularly, loss models adopting different formulations and solutions to the Helmholtz equation to solve for the eddy currents are compared to a simpler model relying on an assumed eddy-current distribution. Boundaries in terms of magnet dimensions and angular frequency are identified (numerically and using an identified approximate analytical expression) to aid the machine designer whether the more simple loss model is applicable or not. The assumption of a uniform flux-density variation (used in the loss models) is also investigated for the case of V-shaped and straight interior permanent magnets. Finally, predicted volumetric loss densities are exemplified for combinations of slot and pole numbers common in automotive applications.

A low-cost bio-mass-derived carbon substrate has been employed to synthesize MoS₂@carbon composites through a hydrothermal method. Carbon fibers derived from natural cotton provide a three-dimensional and open framework for the uniform growth of MoS₂ nanosheets, thus constructing hierarchically coaxial architecture. The unique structure could synergistically benefit fast Li-ion and electron transport from the conductive carbon scaffold and porous MoS₂ nanostructures. As a result, the MoS₂@carbon composites, when served as anodes for Li-ion batteries, exhibit a high reversible specific capacity of 820 mAh g^-1, high-rate capability (457 mAh g^-1 at 2 A g^-1), and excellent cycling stability. The superior electrochemical performance makes the MoS₂@carbon composites to be low-cost and promising anode materials for Li-ion batteries.

This paper focus on the modeling and time-domain analyzing method of piecewise-smooth fractional-order circuit systems. Firstly, an analytical framework is constructed based on a generalized piecewise-smooth two-port impedance network model, which takes the topological characteristics of Dickson type switched-capacitor converters (SCCs) as examples, and considers the fractional-order characteristics of class-2 X7R ceramic capacitors, which are widely used in SCCs. Secondly, the time-domain analyzing method for such a piecewise-smooth fractional-order circuit system is developed, numerical solutions are obtained, and the influence of the fractional-order capacitor on the power conversion efficiency of the system are revealed. Finally, in order to validate the analysis, both numerical simulation and experiments are provided in the work, the results of which confirm that, the proposed fractional-order analytical framework can capture the power loss mechanism of piecewise-smooth fractional-order circuit systems more effectively than the traditional integer-order based approach, thus benefiting the design of circuit systems.

The statistical analysis of impact of the top 50 solar flares of X-class (1997-2023) on the global seismic activity, as well as on the earthquake preparation zones located in illuminated part of the globe and in the area of 5000 km radius around the subsolar point was carried out. It is shown by a method of epoch superposition that for all cases the increase of seismicity is observed, especially in the region around the subsolar point (up to 38%) during 10 days after the solar flare in comparison with preceding 10 days. The case study of aftershock sequence of strong M=9.1 earthquake (Su-matra-Andaman Islands, 26.12.2004) after the solar flare of X7.2 class (20.01.2005) demonstrated that the number of aftershocks with magnitude M≥2.5 increases more than 20 times after the solar flare with a delay of 7 days. For the case of the Darfield earthquake (M=7.1, 04.09.2010, New Zealand) it was shown that strong solar flares of class X and M probably triggered two strong aftershocks (M>6) with the same delay of 6 days on the Port Hills fault, which is the most sensitive to external electromagnetic impact from point of view of the fault electrical conductivity and orientation. Based on the obtained results the possible application of natural electromagnetic triggering of earthquakes is discussed for a short-term earthquake prediction using confidently recorded strong external electromagnetic triggering impacts on the specific earthquake preparation zones, as well as ionospheric perturbations due to aerosol emission from the earthquake sources recorded by satellites.

Densely urbanized areas, with a low percentage of green vegetation, are highly exposed to Heat Waves (HW) which nowadays are increasing in terms of frequency and intensity also in the middle-latitude regions, due to ongoing Climate Change (CC). Their negative effects may combine with those of the UHI (Urban Heat Island), a local phenomenon where air temperatures in the compact built up cores of towns increase more than those in the surrounding rural areas, with significant impact on the quality of urban environment, on citizens health and energy consumption and transport, as it has occurred in the summer of 2003 on France and Italian central-northern areas. In this context this work aims at designing and developing a methodology based on aero-spatial remote sensing (EO) at medium-high resolution and most recent GIS techniques, for the extensive characterization of the urban fabric response to these climatic impacts related to the temperature within the general framework of supporting local and national strategies and policies of adaptation to CC. Due to its extension and variety of built-up typologies, the municipality of Rome was selected as test area for the methodology development and validation. First of all, we started by operating through photointerpretation of cartography at detailed scale (CTR 1: 5000) on a reference area consisting of a transect of about 5x20 km, extending from the downtown to the suburbs and including all the built-up classes of interest. The reference built-up vulnerability classes found inside the transect were then exploited as training areas to classify the entire territory of Rome municipality. To this end, the satellite EO HR (High Resolution) multispectral data, provided by the Landsat sensors were used within a on purpose developed "supervised" classification procedure, based on data mining and “object-classification” techniques. The classification results were then exploited for implementing a calibration method, based on a typical UHI temperature distribution, derived from MODIS satellite sensor LST (Land Surface Temperature) data of the summer 2003, to obtain an analytical expression of the vulnerability model, previously introduced on a semi-empirical basis.

This work (in two parts) will review the recently developed predictive modeling methodology called “4th-BERRU-PM” and its applicability to energy systems as exemplified by an illustrative application to the Polyethylene-Reflected Plutonium (acronym: PERP) OECD/NEA reactor physics benchmark. The acronym 4th-BERRU-PM designates the “Fourth-Order Best-Estimate Results with Reduced Uncertainties Predictive Modeling” methodology, which yields best-estimate results with reduced uncertainties for the first fourth-order moments (mean values, covariance, skewness, and kurtosis) of the optimally predicted posterior distribution of model results and calibrated model parameters. The 4th-BERRU-PM uses the Maximum Entropy (MaxEnt) principle to incorporate fourth-order experimental and computational information, including fourth (and higher) order sensitivities of computed model responses to model parameters, thus incorporating, as particular cases, the results previously predicted by the second-order predictive modeling methodology 2nd-BERRU-PM, and vastly generalizing the results produced by extant data assimilation and data adjustment procedures. The 4th-BERRU-PM methodology encompasses the scopes of high-order sensitivity analysis (SA), uncertainty quantification (UQ), data assimilation (DA) and model calibration (MC). The application of the 4th-BERRU-PM methodology to energy systems is illustrated by means of the above-mentioned OECD/NEA reactor physics benchmark, which is modeled using the neutron transport Boltzmann equation involving 21976 imprecisely known parameters, the solution of which is representative of “large-scale computations.” The model result (“response”) of interest is the leakage of neutrons through the outer surface of this spherical benchmark, which can be computed numerically and measured experimentally. Part 1 of this work illustrates the impact of high-order sensitivities, in conjunction with parameter standard deviations of various magnitudes, on the determination of the expected value and variance of the computed response in terms of the first four moments of the distribution of the uncertain model parameters. Part 2 of this work will illustrate the capabilities of the 4th-BERRU-PM methodology for combining computational and experimental information, up to and including forth-order sensitivities and distributional moments, for producing best-estimate values for the predicted responses and model parameters while reducing their accompanying uncertainties.

Due to environmental concerns, natural refrigerants and their use in refrigeration and air conditioning systems are receiving more attention from manufacturers, end users and the scientific community. The study of heat transfer and pressure drop is essential for accurate design and more energy efficient cycles using natural refrigerants. The aim of this work is to provide an overview of the latest outcomes related to heat transfer and pressure drop correlations for ammonia, propane, isobutane and propylene and to investigate the current state of the art in terms of operating conditions. Available data on the existing correlations of heat transfer coefficient and pressure drop for natural refrigerants have been collected through a systematic search. Whenever possible, validity intervals are given for each correlation and the error is quantified. It is the intention of the authors that this could be a valuable support for researchers and an aid to design, with particular reference to heat pumps. A procedure based on the Preferred Reporting Items for Systematic Reviews and Meta-Analyses (PRISMA) statement was adopted, and the Scopus database was used to query the relevant literature. A total of 135 publications qualified for inclusion in the survey; 34 articles report experimental investigations for not usual geometric conditions. Of the 101 selected papers related to usual geometric conditions, N = 50 deal only with HTC, N = 16 deal only with pressure drop and the remainder (N = 35) analyse both HTC and pressure drop. Among the 85 HTC papers (N = 53) deal with the evaporating condition, N = 30 with condensation and only N = 2 with the heat transfer correlations under both conditions. Most of the 101 articles concern propane and isobutane. The high temperatures are less widely investigated.

Abstract: High step-up voltage gain nonisolated DC-DC converter have attracted much attention in photovoltaic, fuel cells and other renewable energy system applications. In this paper, by combining input current ripple-free boost cell with coupled-inductor voltage-doubler cell, an input current ripple-free high voltage gain nonisolated converter is proposed. In addition, passive lossless clamp circuit is adopted to recycle the leakage inductor energy and to reduce the voltage spike across the power switch. By utilizing voltage-doubler cell consisting of diode and capacitor, the voltage stress of switch is further reduced and the resonance between the leakage inductor and the stray capacitor of the output diode is eliminated. A low switch-on-resistance low-voltage-rated MOSFET can therefore be employed to reduce the conduction loss and cost. The reverse recovery loss of output diode is reduced, and the efficiency of converter can be improved. Furthermore, the proposed converter can achieve nearly zero input current-ripple and make the design of electromagnetic interference (EMI) filter easy. Steady state analysis and operation mode of the converter is performed. Finally, experimental results are presented to verify the analysis results of the proposed converter.

The Energy Performance of Buildings Directive 2010 calls for the Nearly Zero Energy Standard for new buildings from 2021 onwards: Buildings using “almost no energy” are powered by renewable sources or energy produced by the building itself. For residential buildings, this ambitious new standard has already been reached. But for other building types this goal is still far away. The potential of these buildings to meet a Nearly Zero Energy Standard was investigated by analyzing ten case studies representing non-residential buildings with different uses. The analysis shows that the primary characteristics common to critical building types are a dense building context with a very high degree of technical installation (such as hospital, research and laboratory buildings). The large primary energy demand of these types of buildings cannot be compensated by building and property-related energy generation including off-site renewables. If the future Nearly Zero Energy Standard were to be defined with lower requirements because of this, the state related properties of Bavaria suggest that the real potential energy savings available in at least 85% of all new buildings would be insufficiently exploited. Therefore, it would be useful to instead individualize the legal energy verification process for new buildings to distinguish critical building types such as laboratories and hospitals.

Genetic diversity is very important in crop improvement. This study was carried out to assess the genetic diversity and the number of unique multilocus genotypes (MLGs) in cassava collection in Burkina Faso. To achieve this objective 130 cassava accessions were genotyped using 32 simple sequence repeat (SSR) markers. The results revealed that among these markers, twelve (12) were highly informative, with the PIC values greater than 0.50, twelve (12) were moderately informative, with the PIC values ranged between 0.25 and 0.50, and eight (8) were not very informative, with the PIC values lower than 0.25. A moderate level of genetic diversity was found for the population, indicated by the average expected heterozygosity (0.45) and the observed heterozygosity (0.48). About 83.8% of unique multilocus genotypes were found in the cassava collection indicating that SSR markers seem to be most appropriate for MLGs identification. Population structure analysis based on hierarchical clustering identified two subpopulations and Bayesian approach suggested five clusters. Additionally, DAPC analysis separated the cassava accessions into 13 subpopulations. The comparison of these results and the previous study using SNP, suggest that each type of markers can be used to assessment the genetic structure of cassava grown in Burkina Faso.

Wave energy converter (WEC) arrays deployed in coastal regions may create physical disturbances potentially resulting in environmental stresses. Presently, limited information is available on the nature of these physical disturbance or the resultant effects. A quantitative Spatial Environmental Assessment Tool (SEAT) for evaluating potential effects of wave energy converter (WEC) arrays on nearshore hydrodynamics and sediment transport is presented for the central Oregon coast (USA) through coupled numerical model simulations of an array of WECs. Derived climatological wave conditions were used as inputs to the model to allow for the calculation of risk metrics associated with various hydrodynamic and sediment transport variables such as maximum shear stress, bottom velocity, and change in bed elevation. The risk maps provided simple, quantitative, and spatially-resolved means of evaluating physical changes in the vicinity of a hypothetical WEC array in response to varying wave conditions. Near-field risk of sediment mobility was determined to be moderate in the lee of the densely spaced array, where the potential for increased sediment deposition could result in benthic habitat alteration. Modifications to the nearshore sediment deposition and erosion patterns were observed near headlands and topographic features, which could have implications for littoral sediment transport. The results illustrate the benefits of a risk evaluation tool for facilitating coastal resource management at early market marine renewable energy sites.

Coastal inundation is recently requiring a significant attention worldwide. The increasing frequency and intensity of extreme events (sea storms, tsunami waves) are highly stressing the coastal envi-ronments, e.g. endangering a large number of residential areas, ecosystems, tourist facilities, and also leading to potential environmental risks. Predicting such events and the generated coastal flooding is thus of paramount importance and can be reached by exploiting the potential of different tools, like remote sensors and numerical modeling. To this aim, a combination is possible between marine radars and wave-resolving propagation models. While instruments like X-band radars are able at precisely reconstructing both wave field and bathymetry within a coastal area that is some kilometers offshore, wave-resolving Boussinesq-type models can reproduce the wave propagation in the nearshore and the consequent coastal flooding. The present work illustrates the reconstruc-tion of coastal data (wave field and seabed depth) conducted using radar signals and a specifically suited data processing, named “Local Method”, and the use of such coastal data to run numerical simulations of wave propagation (using the FUNWAVE-TVD solver) aimed at reproducing coastal inundation over different scenarios. Such scenarios are built using two different European beaches, i.e. Senigallia (Italy) and Oostende (Belgium), and three different directional spreading values, to evaluate the performances in case of either long- or short-crested waves. The overall validation of the methodology, in terms of maximum inundation, shows good performances, especially in case of short-crested wind waves. Furthermore, the application on the Oostende beach demonstrates that the present methodology might work only using open-access tools, i.e. an easy investigation of the coastal inundation and a potential low-cost integration into early warning systems.

The importance of frailty in older people is getting constant recognition as an important aspect both in terms of public health, as well in personal level for the appropriate management of an older person health condition. This is reflected by the continuously increasing number of research studies carried out in several settings across different countries. Sometimes this is very solid, but in other cases there is a considerable gap in terms of accurate and well grounded documentation of frailty status. This is the case in Greece, where we are missing clinically validated tools to approach frailty. We are missing frailty screening tools, such as for instance PRISMA 7, the gold standard tool of Fried criteria is somehow problematic since the question referring to physical activity originates from a questionnaire that has not been translated and validated, while Clinical Frailty Scale has been validated for the translation but not for the capacity to detect frailty. Aim of this study is to validate these tools for their accuracy to detect frailty by using a measurable index of frailty, previously proposed for use in clinical studies: the Short Physical Performance Battery (SPPB). 74 male and female participants have been evaluated for their frailty status using different tools. We observed that PRISMA 7 translation detects frailty only when one question is removed at a cut-off of ≥ 2 and indicated a sensitivity of 88.1%, and specificity of 99.9% with a good correlation with SPPB measurements (r = 0.858; p < 0.001). When CFS was validated using SPPB it demonstrated a very good correlation (r = -0.838; p < 0.001 respectively) as it was the case for the modified Fried Criteria (r = -0.725; p < 0.001). All items demonstrated a good correlation between them. We can here propose that we can accurately assess frailty status in the community setting by using a modified version of Fried criteria, Clinical Frailty Scale translation in Greek and we can screen for frailty by using the Greek translation of PRISMA 7 only after removing the item 6 of the questionnaire.

In the face of escalating climate concerns and the push for sustainable development, the global shift towards renewable and decentralized energy systems presents new challenges and opportunities. This study investigates integrating decentralized energy production, particularly photovoltaic (PV) systems, into national energy planning, aiming to optimize energy strategies that balance local production and consumption with national objectives. By analyzing the Swiss energy model, the research employs the EnergyScope and REHO models to assess the strategic implications of decentralized versus centralized energy systems. Results show that a decentralized approach can significantly reduce PV installation needs to 35 GW, about 23% of potential capacity, and decrease annual system costs by 10% to CHF 1230 per capita. This strategy emphasizes local consumption, minimizes grid reinforcement demands, and leverages economic advantages while addressing overproduction challenges through effective energy storage and grid management. Conclusions underline the strategic value of combining centralized and decentralized methods for resilient and sustainable energy planning. The study contributes to the discourse on energy policy and infrastructure planning, advocating for a hybrid model that accommodates both local conditions and broader energy objectives, urging further research into climate impacts and technology integration for a comprehensive energy future.

Plastic waste accumulation poses significant environmental challenges, underscoring the importance of closing the plastic life cycle by converting waste into valuable products. Pyrolytic char, a promising byproduct, offers diverse industrial applications. However, little attention has been given to converting hydrocarbon-based plastics into solid carbon due to their low fixed carbon content. This study compares sulfonation and thermal oxidation stabilization techniques for carbonizing waste polyethylene and polyvinyl chloride. Results indicate sulfonation yields higher pyrolytic char formation and improves surface properties, surpassing Al2O3 in catalyst support characteristics. Thermal oxidation increases fixed carbon content but adversely affects char yield and surface properties. Both methods effectively enhance fixed carbon content, but sulfonation emerges as more advantageous, suggesting potential use of plastic-derived char as a catalyst support material, contributing to circular economy development.

The question of the relevance of human and natural capital, as well as the potential adverse effect of natural capital on economic growth, has gained increased attention in development economics. The aim of this paper is to theoretically and empirically assess the relevance of several forms of capital on economic growth in small economies that are dependent upon tourism or natural resources. The empirical framework is based on Impulse Response Functions obtained from Vector Autoregressive models in which we focus on the model where economic growth is the dependent variable for ten small economies that are dependent upon either tourism or natural resources. We find that there is evidence of the ‘’natural resource curse’’, especially in the economies that have a strong dependence on resources that are easily substitutable and whose prices constantly fluctuate. We further find that in the majority of observed cases the type of capital these small economies are most dependent on for their economic growth causes negative impulses in the majority of the observed periods. The main policy recommendation should be to assure that even these small economies should strive towards further diversification and avoid dependence on only one segment of their economy.

Three-dimensional V₂O₅ hollow structures have been prepared through a simple synthesis strategy combining solvothermal treatment and a subsequent thermal annealing. The V₂O₅ materials are composed of microspheres 2–3 μm in diameter and with a distinct hollow interior. The as-synthesized V₂O₅ hollow microspheres, when evaluated as a cathode material for lithium-ion batteries, can deliver a specific capacity as high as 273 mAh·g⁻¹ at 0.2 C. Benefiting from the hollow structures that afford fast electrolyte transport and volume accommodation, the V₂O₅ cathode also exhibits a superior rate capability and excellent cycling stability. The good Li-ion storage performance demonstrates the great potential of this unique V₂O₅ hollow material as a high-performance cathode for lithium-ion batteries.

In this study, the causal-effect between carbon dioxide emissions and forestry production and trade was investigated in Ghana by employing a data spanning from 1961 to 2014 by using the VECM and ARDL model. Evidence of the long-run equilibrium relationship in the VECM shows that, a 1% increase in veneer sheet production reduces carbon dioxide emissions by 1.47% in the long-run. There was evidence of a bidirectional causality between carbon dioxide emissions and veneer sheet production, carbon dioxide emissions and wood charcoal production, and a unidirectional causality running from carbon dioxide emissions to wood fuel production and plywood production to carbon dioxide emissions. Evidence from the long-run equilibrium relationship in the ARDL model shows that; a 1% increase in plywood production will increase carbon dioxide emissions by 0.17% in the long-run, a 1% increase in sawnwood production will increase carbon dioxide emissions by 0.17% in the long-run, a 1% increase in wood charcoal production will increase carbon dioxide emissions by 0.36% in the long-run and a 1% increase in wood fuel production will increase carbon dioxide emissions by 0.37% in the long-run.

In this study, an attempt was made to investigate the Kenya case of multivariate causality of carbon dioxide emissions by employing a time series data spanning from 1961-2011 using the ARDL method of cointegration analysis. The long-run elasticities show that, a 1% increase in financial development increases carbon dioxide emissions by 0.28%, a 1% increase in GDP per capita increases carbon dioxide emissions by 1.32% and a 1% increase in urbanization decreases carbon dioxide emissions by 1.14%. There was a unidirectional causality running from financial development, food production index, GDP per capita, industrialization and urbanization to carbon dioxide emissions. The innovation accounting shows that 20% of future shocks in carbon dioxide emissions are due to fluctuations in financial development, 9% of future shocks in financial development are due to fluctuations urbanization and 22% of future shocks in food production index are due to fluctuations in carbon dioxide emissions.

This study presents the synthesis and electrochemical evaluation of nitrogen-doped vanadium oxide (N-V2O3/C) as a cathode material for aqueous zinc-ion batteries (AZIBs), using a hydrothermal method. Compared to undoped V2O3/C, N-V2O3/C exhibits enhanced electrical conductivity, capacity, and electrochemical kinetics, attributed to the incorporation of pyridinic and pyrrolic nitrogen. Initial charge-discharge cycles indicate phase transitions to amorphous vanadium oxides, enhancing conductivity. N-V2O3/C shows a high specific capacity of 168.4 mAh g−1 at 10 A g−1 and remarkable reversibility, highlighted by the transient existence of intermediate species during cycling. Optimal electrochemical performance is achieved with a vanadium to nitrogen molar ratio of 2:3, indicating the significant impact of nitrogen doping concentration on the material’s efficiency. This work underscores the potential of N-V2O3/C as a superior cathode material for AZIBs.

Using density functional theory (DFT), the density of states of NH4V3O8 (NVO) was analyzed pre and post-oxygen defects (Od) formation. The findings revealed a reduced bandgap in NVO after Od introduction, emphasizing the role of Od in enhancing conductivity of the material, thus improving its electrochemical attributes. Through the water bath method, both NVO and its oxygen-deficient counterpart, (NH4)2V10O25⸱8H2O (NVOd), were synthesized as potential cathode materials for aqueous zinc-ion batteries (AZIBs). Experimental outcomes resonated with DFT predictions, highlighting the beneficial role of oxygen defects in boosting electrical conductivity. Notably, the refined material displayed a remarkable capacity of 479.3 mAh g-1 at 0.1 A g-1, underscoring its promise for advanced energy storage solutions.

A method based on ultra performance liquid chromatography with diode array detector (UPLC-DAD) was developed for quantitative analysis of five active compounds and chemical fingerprint analysis of Rosa rugosa. Ten batches of Rosa rugosa collected from different plantations in the Xinjiang region of China were used to establish the fingerprint. The feasibility and advantages of the used UPLC fingerprint were verified for its similarity evaluation by systematically comparing chromatograms with professional analytical software recommended by State Food and Drug Administration (SFDA) of China. In quantitative analysis, the five compounds showed good regression (R²=0.999 5) within the test ranges and the recovery of the method was in the range of 94.2–103.8%. The similarities of the fingerprints of 10 batches of the samples were more than 0.981. The developed UPLC fingerprint method is simple, reliable and validated for the quality control and identification of Rosa rugosa. Additionally, simultaneous quantification of five major bioactive ingredients in the Rosa rugosa samples was conducted to interpret the consistency of the quality test. The results indicated that the UPLC fingerprint as a characteristic distinguishing method combining similarity evaluation and quantification analysis, can be successfully used to assess the quality and to identify the authenticity of Rosa rugosa.

Improper disposal of waste plastic has caused serious ecological and environmental pollution problems. Transforming plastics into high value-added chemicals can not only achieve efficient recycling of waste plastics, but also an effective way to control white pollution. The catalyst selectively breaks the C-C bond of polyolefin plastic under heat treatment and converts it into liquid fuel, thus realizing sustainable recycling of plastics and has a good development prospect. This review provides a detailed overview of the current development of catalytic pyrolysis, catalytic hydrolysis, solvent decomposition and supercritical hydrothermal liquefaction for cracking plastics to make fuel oil. The reaction mechanism, influencing factors and promoting effects of catalysts in various degradation technologies are analyzed and summarized and the latest proposed tandem reaction for degrading plastics is briefly introduced. Finally, some optimization paths of waste plastic pyrolysis to fuel oil technology are proposed: synergies between mixed raw materials, in-depth exploration of catalysts, design and manufacture of reactors that match the pyrolysis technology. All these are important research directions for promoting the industrialization of plastic pyrolysis to fuel oil.

The study was conducted in north wollo, south wollo and orimiya zone, in Eastern Amhara with an aim to assess the resource potential of Acacia seyal in the selected sites. The data from the selected sites were collected using point center quarter method. A total of 90 quadrates from nine study areas with plot size 50m*50m, (22.5ha) were systematically located along each transect, 100 m apart, and was spatially captured with the aid of GPS. At every sampling point, four quadrants (90 degrees) were created, using the transect line and a line perpendicular to it. Species composition Acacia seyal structure and its regeneration status, at points along transects were taken to analyze diversity and target species structure of the sites. The highest and least density of Acacia seyal ha^-1 were attained by Mehale mecharie (148) and Alene sefer (52). The highest shannon weiner diversity and species richness was observed in Alene sefer(Kemessie). Acacia seyal structure in all study sites showed an inverted J shape except lastie gerdao (Gubalafeto). Therefore, Acacia seyal deserves immediate conservation and appropriate management measures in order to get sustainable product and services from the species. Based on the results, awareness creation on the values and management of Acacia seyal, study on the management options of Acacia seyal for firewood, fuel wood, charcoal production and also investigation of gum production techniques of Acacia seyal for the sustainable use of the resource are recommended.

The Himalaya is well known for high diversity and ethnobotanical uses of medicinal plants. However, not all areas of the Himalayas are well studied. In particular, studies on ethnobotanical uses of plants from the Eastern Himalayas are rare and lacking for many tribes. Past studies primarily focused on listing plants name and their traditional medicinal uses. However, studies on traditional ethnopharmacological practices on medicine preparation had not yet been reported in published literature from the Eastern Himalaya. In this study, we are reporting the first time ethnopharmacological used 24 medicines, their procedures of preparation and listed 53 plant species used for those medicines for Monpa tribe. Such documentations had not yet been done for other tribes in India. Our research demonstrates the urgent need to documents traditional medicine preparation procedures from the local healers before rapid cultural modernization forgets them in transforming country like India. This study should motivate national and international researchers to do more works on ethnopharmacology and bioprospecting.

Ocean wave energy is a significantly well-liked renewable energy source. The Internet of Things (IoT) offers a great opportunity for development of the ocean wave energy research. The IoT technology significantly enhanced the performance of the ocean wave energy converter (WEC). The data obtained from IoT devices reduce the risk of using WEC. However, Integrating IoT devices with the WEC is a daunting task because controlling the WEC needs real-time data. This paper investigated the performance of WEC and estimate the lifetime of the modules. IoT devices integrated with various sensors determine different parameters and conditions of the ocean. The IoT platform is used for wireless voltmeters, wireless AC current meters, wireless voltage detection, wireless resistance sensors, wireless temperature sensor, wireless accelerometer, wireless pressure meters, and wireless water level sensors to determine the real-time condition of the ocean wave. These devices are also proven to be reliable and accurate.

This work condenses various modeling techniques for different Point Absorber configurations. A combined frequency - time domain model will be developed in Matlab-FORTRAN in order to compute the displacement, velocities and the power absorbed in the heave mode. Additionally, a single buoy motion including multiple degrees of freedom will be investigated as well. Therefore, the diffraction-radiation Boundary Element Method solvers NEMOH and BEMIO will be applied in the calculation of the hydrodynamic coefficients, which will determine the solution of Newtons impulse equations of motion. Initially, the Wave to wire model will be validated through comparison with previous experimental results for a submerged cone cylinder shape (Buldra-FO3). A single, generic, vertical floating cylinder will be contemplated then, that responds to the action of the passing waves excitation. Later, two vertical floating cylinders aligned with the incident wave direction will be modeled for a variable distance between the bodies. For both unidirectional regular and irregular waves as an input in deep water, the convolutive radiation force function term will be hereby approximated through the Prony method. By changing the spatial disposition of the axisymmetric buoys, using for instance triangular or diamond shaped arrays of three and four bodies respectively, the study will focus on the interaction effects for regular waves. The results will highlight the most efficient layout for maximizing the energy production whilst providing important insights into their performance, revealing for instance displacement amplification or capture width ratios in near-resonance conditions.

Abstract: Due to sever land degradation throughout Ethiopia, the government has been implementing massive soil and water conservation works at the watershed scale since 2010 to conserve soil and water resources. However, most of the rivers in Ethiopia carry huge amount of sediment in rainy season and streams dried up in the dry period. Planned research was conducted on two paired micro-catchments Mt.Yewel with the main objective of evaluating the impact of soil and water conservation measures on base flow modification. Stream flow and rainfall data were collected from 22/11/2020 to 8/11/2022 on both micro-catchments at their outlets and center respectively. Base flow separation was done using Sp. Hydro base flow separation tool and SPSS Ver.21 statistical software was employed for data analysis. Flow duration curve (FDC) for both watersheds were developed. The FDC indicated that the base flow from treated micro-catchment ishigher and sustained in the dry season while it is low and un-sustained in untreated micro-catchment. From statistical analysis, there is a significant difference in base flow enhancement between the treated and untreated micro-catchment (P<0.001). Hence, catchment treatment contributed to improve groundwater recharge and sustain base flow in the dry season by reduce surface runoff during rainy season.

The new unique technology for granulation of metals and nonmetallic melts is presented in the paper. It was created on the newly developed controlled film flow disintegration with rapid cooling of the droplets and solidified granules in amorphous state. Three new phenomena discovered by us created the base for 3 different methods for granulation of metals and nonmetallic melts in a wide range of granules’ sizes. Electromagnetic resonance method allows producing granules of metals in the range of 1 mm and over. The soliton-like vibrational regime is available for production of any granulation material in the range 0.1-1 mm. Moreover, the shockwave regime is applicable for producing particles from 10 micrometers by size. All methods produce particles of the stated size with a narrow distribution by size: deviation from the average size no more than 50%. The other known methods do not produce granules with such high cooling rate, which can realize the amorphous state and cannot regulate size of particles in such bright but narrow range from 10 micrometers to 1-2 mm.

In this work, satellite data from the Clouds and Earth’s Radiant Energy System (CERES) and Moderate Resolution Imaging Spectroradiometer (MODIS) instruments is analyzed to determine how the global absorbed sunlight and global entropy generation rate have changed during the time period from 2002 to 2023. The data is used to test hypotheses derived from the Maximum Power Principle (MPP) and Maximum Entropy Production Principle (MEP) about the evolution of earth’s surface and atmosphere. The results indicate that the amount of absorbed sunlight has increased over the last 20 years but rising surface temperatures have caused the entropy generation rate to remain approximately constant despite that decrease in albedo. The results are simpler to explain using the MPP but do not completely rule out the MEP. Given the acceptance of the MPP or MEP, some extensions and nuances are discussed.

Volatile organic compounds (VOCs) released from plants have been correlated with disease-status. Analysis of VOCs using GC-MS is time-consuming, laboratory-based, and requires specialist training. Electronic nose devices (E-nose) provide a portable alternative. Three different E-nose devices were compared to assess how accurately they could detect Mango Twig Tip Dieback and Panama disease in banana. The devices were initially trained on known volatiles, then pure cultures of Pantoea sp., Staphylococcus sp., and Fusarium odoratissimum, and finally, on infected and healthy mango leaves and field-collected, infected banana pseudo-stems. The experiments were repeated three times with six replicates for each host-pathogen pair. The variation between healthy and infected host materials was evaluated by principal component and linear discriminant analysis, cross-validation and chemometric data analysis. GC-MS analysis was conducted contemporaneously and identified an 80% similarity between healthy and infected plant material. The portable C 320 was 100% successful in discriminating known volatiles but had a low capability in differentiating healthy and infected plant substrates. The advanced devices (PEN 3 / MSEM 160) successfully detected healthy and diseased samples with a high variance. The results suggest that E-nose devices are more sensitive and accurate in detecting changes of VOCs between healthy and infected plants compared to headspace GC-MS.

This paper analyses the application of deep learning techniques for predicting wave overtopping events in port environments using sea state and weather forecasts as inputs. The study was conducted in the outer port of Punta Langosteira, A Coruña, Spain. A video recording infrastructure was installed to monitor overtopping events from 2015 to 2022, identifying 3709 overtopping events. The data collected was merged with actual and predicted data for the sea state and weather conditions during the overtopping events, creating three datasets. We used these datasets to create several machine learning models to predict whether an overtopping event would occur based on sea state and weather conditions. The final models achieved a high accuracy level during the training and testing stages: 0.81, 0.73, and 0.84 average accuracy during training and 0.67, 0.48, and 0.86 average accuracy during testing, respectively. The results of this study have significant implications for port safety and efficiency, as wave overtopping events can cause disruptions and potential damage. Using deep learning techniques for overtopping prediction can help port managers take preventative measures and optimize operations, ultimately improving safety and helping to minimize the economic impact that overtopping events have on the port's activities.

Abstract: Severe land degradation is the principal environmental problem in Ethiopian highlands in the form of soil erosion, and soil fertility loss, which is caused by human intervention for food, shelter, and energy demands. Soil erosion contributes to the loss of precious soil and water resources which are the basis of agricultural production and provide numerous other eco-system services. The Ethiopian highlands are one of the most degraded regions in the world. To combat such problems, the government of Ethiopia has been implementing massive soil and water conservation works at the watershed scale since 2010 to conserve soil and water resources. Mount Yewel is one of the highlands in Northeastern Ethiopia where intensive soil and water conserva-tion has been implemented. Despite the massive investment in soil and water conservation measures, most of the rivers in the highlands of Ethiopia carry huge amounts of sediment with high flood risks in the wet season and streams are dried up in the dry period. Nonetheless, the impact of soil and water conservation measures on flood reduction and dry season flow en-hancement has not yet been quantified and evaluated. This research was then conducted on paired micro-catchments of Mount Yewel with the main objective of evaluating the impact of soil and water conservation measures on base flow modification. Stream flow and rainfall data were col-lected from 22/11/2020 to 8/11/2022 on paired micro-catchments of Mount Yewel at their outlets and centers respectively. Base flow separation was done from the stream hydrograph using Sp. Hydro base flow separation tool and SPSS Ver.21 statistical software were employed for data analysis. Flow duration curves (FDC) for both watersheds were developed to compare the stream flow patterns between treated and untreated micro-catchments of Mount Yewel. The FDC indi-cated that the base flow from treated micro-catchment is higher and sustained in the dry season while it is low and unsustained in untreated micro-catchment. From statistical analysis, there is a significant (P

A Shape Memory Alloy (SMA) enabled Overtopping Wave Energy Converter (OWEC) that maximizes its overtopping discharge, and thus energy output under different wave conditions is presented. Among all the parameters affecting the overtopping discharge rate, the crest freeboard height is the most influential one to control the overtopping discharge rate and the stored overtopping volume behind it. Currently, all the OWEC crest freeboard heights are fixed by design to maximize the discharge rate on one particular sea state. In the present study, we show that the SMA can adjust the crest freeboard height through a control system based on the sea state and achieve an optimal overtopping discharge rate. A scaled OWEC model is built in the lab with its crest freeboard height controlled by springs made of SMA. The length (and thus tension) of the springs is controlled by temperature changes by changing the passing current through the springs. By adjusting the length of the springs based on the incoming wave condition, we adjust the freeboard to an optimal height known to generate a maximum overtopping discharge rate for energy conversion. This smart material-enabled design can maximize the overtopping discharge and thus the output power of the OWEC under various wave conditions. Furthermore, the simplicity of using SMA springs as the actuator leads to the minimum number of moving mechanical parts, which can remarkably decrease maintenance costs. As the proof of concept, two types of tests are conducted in the laboratory using the same OWEC model under several random wave trains generated from spectra with different significant wave heights - one type with a fixed crest freeboard height and the other type featuring the adjustable crest freeboard height controlled by the springs. The substantial increase of harvested output power in the OWEC with the adjustable crest freeboard height may pave the way for more efficient wave energy conversion systems.

A large set of undrained compression triaxial tests was carried out on different types of cohesionless soils, from sands to silty-sands and silts. Shear wave velocity measurements were carried out alongside. These tests exhibited distinct state transitions ranging from flow liquefaction to strain softening or strain hardening. With the purpose of defining a framework to assess soil liquefaction, it was found that the ratio between the shear wave velocity (VS0) and the peak undrained deviatoric stress, qpeak, VS0/qpeak, could be accurately used to define a boundary between liquefaction and strain hardening for sands, and between strain softening and strain hardening for silty-sands and silts. Since this ratio is a function of the tested material, it was also discovered that the prediction of these boundaries could be made as a function of soil grading, namely via the coefficient of uniformity, CU. Despite not being regarded as a strong geomechanical parameter, CU is easily determined from a grain-size distribution test and it has an empirically proven correlation with critical state parameters.

Biotechnological potential of Thermoanaerobacter strain AK15 to produce ethanol and valuable alcohols from carbohydrates and amino acids were evaluated in present study. The strain is highly ethanologenic, producing a maximum of 1.57 mol ethanol per mol of glucose degraded at high liquid-gas phase ratios. The strain degrades most of the sugars tested as well as starch and pretreated hydrolysates of biopolymers (Whatman paper, newspaper, Timothy grass, Rhubarb leaves, and several macroalgae species) to ethanol mainly. The strains degraded serine and threonine when used as a single substrate, producing mainly acetate and ethanol as end products, and the branched-chain amino acids (leucine, isoleucine, valine) when cultivated in the presence of thiosulfate. The main end products from branched-chain amino acids were a mixture of their corresponding branched-chain fatty acids and alcohols. Finally, the strain was also shown to use butyrate as an electron sink during glucose degradation resulting in the reduced product butanol in addition to end products produced from glucose. Thus, strain AK15 is a promising candidate for ethanol and fine chemical production from a range of lignocellulosic and algal biomass.

Coastal wave modeling and forecasting are essential in oceanography, sustainable marine energy, and ocean engineering. Precise forecasting of wave speed and direction are crucial for offshore operations, marine energy, risk management, environmental management, coastal and sustainable maritime management. The coastline of Brunei Darussalam can generate between 15 and 126 Giga Watt of wave energy. In this experimental research, we used two numerical approaches, the finite difference, and spectral element methods, to model and simulate wave speed and direction. We calculated the mean error between numerical and analytical solutions. We proposed a novel, promising, univariate time series forecasting model by combining the Long Short-Term (LSTM) with KerasTuner hyperparameters tuning and optimization techniques. This method helps us to improve the accuracy and efficiency of time-series forecasting.. The experimental data was computed from high-precision Acoustic Doppler Current Profiler (ADCP) sensor data. This research is part of the preliminary feasibility analysis of wave energy production in Brunei Darussalam and net zero commitment for a sustainable environment. Seven independent forecast experiments were performed for wave speed and direction in degree and radian units for 1, 3, 6, 8, 10, 12, and 24 hours. Mean squared error (MSE) was adopted as a metric for both training and testing. The experimental results reveal that the wave speed forecast has the lowest MSE compared to direction, regardless of the unit of measure, but has a longer duration. In addition, the direction forecast in the degree unit has the lowest errors compared to the unit of radians; the latter has a longer running time than the former. The model has delivered optimal results throughout the experiments with minor training and test errors. We conducted a thorough evaluations on two benchmark time series datasets, which include the study dataset and air quality index dataset, to validate the performance of the proposed model with other models. The proposed model outperforms cutting-edge forecasting models, such as the conventional LSTM, ARIMA, and Prophet. The model has the slightest forecast error compared to the existing literature’s result.

Biochar is a carbonaceous material derived from the thermochemical conversion of biomass under oxygen-lean conditions. Its properties render it many applications in agriculture, environmental remediation, and catalysis. Commonly produced by pyrolysis under a nitrogen atmosphere, the biochar composition is influenced mainly by residence time, heating rate, and process temperature. The existing literature primarily assesses biochar properties, such as ultimate, proximate, calorific, porosity, and combustibility, generated under various thermo-conversion conditions. However, there is a notable lack of sufficient investigation and attention given to the practical application of biochar. This article seeks to bridge that gap by enhancing the comprehension of the necessary experimental assessment for specific biochar applications and proposing process optimization methods using Multi-Criteria Decision Analysis (MCDA). By delving into these aspects, the study offers a concise overview of biochar production and presents a comprehensive panorama based on articles and patents. Additionally, the research explores the physicochemical characterization techniques associated with biochar and its various applications in conjunction with MCDA. This comprehensive approach aims to uncover valuable insights that could further advance the practical and sustainable utilization of biochar in a wide range of fields.

The increasing demand for higher power in rocket launchers is driving the development of higher power nozzles, achieved essentially by increasing the expansion ratio. However, this can lead to flow separation and resulting unsteady, asymmetrical forces, called side loads, which can limit the life of both the nozzle itself and other engine components. If this problem can be overcome, engine performance can be significantly increased. Therefore, various separation control methods have been proposed, but none have been fully implemented to date due to the uncertainties associated with modeling and predicting the flow phenomena. A numerical study of high area ratio rocket engine is presented to analyze the aeroelastic performance of the structure under the condition of flow separation. The finite volume method, the 2nd order upwind scheme and the extended wall function are used to analyze the flow inside the rocket nozzle and the transition of the Free Shock Separation (FSS) to Restricted Shock Separation (RSS) separation pattern ) to be discussed in detail. Since the location of the flow separation point depends heavily on the flow.

Recycling information can be complex and often confusing which may subsequently reduce the participations in any waste recycling schemes. As a result, this research explored the roles as well as the importance of a holistic approach in designing recycling information using 15 expert-based in-depth interviews. The rationale was to offer a better understanding of what constitutes waste, recycling, and how recycling information should be designed and presented to make recycling more attractive/convenient. Based on the research participants’ perceptions with supports from the existing studies, this research sub-categorised recycling information into three different themes, termed the “WWW” of recycling information components. As a result, these components (or attributes) were extensively described (using findings of semi-structured interviews) to elicit pragmatic guidance for practitioners, policy-makers, and other stakeholders in designing structured communication or information strategies that may simplify and subsequently increase waste-recycling practices. The policy implications of holistic information in enhancing recycling are further discussed.

Shared public buildings have become centers of innovation, integrating advanced technologies to meet evolving societal needs. With a heightened emphasis on occupants’ health and well-being, these buildings serve as hubs for technological convergence, facilitating seamless connectivity and intelligent data analysis and management. Within this context, environmental monitoring emerges as a foundational element, pivotal to all aspects of building management. This article provides findings from the nationally funded RE-START project, which focuses on shared public buildings, with special regard to educational and medical facilities. The project explores enhanced indoor air quality monitoring, focusing in particular on CO2 concentration that is directly correlated with occupancy, as a fundamental element for developing health and safety protocols, energy efficiency strategies, integration of smart building technologies, and data-driven energy management. The intersection of environmental monitoring, energy efficiency, security, and IoT technologies in in indoor spaces are relevant. The outcomes of the study reveal the delicate nature of all the involved components, that need to be carefully developed in an integrated manner.

As the natural resources are getting exhausted, the concept of sustainable development of region has received increasing attentions, especially for resource-dependent cities. In this paper an innovative method that emergy analysis and IPAT (Human Impact Population Affluence Technology) model were combined in order to analyze the quantitative relationship of economic growth and energy consumption and further to evaluate its overall sustainability level. Taiyuan, a traditional, resource-dependent city in China, is selected as the case study region. The main results show that total emergy of Taiyuan increased from 9.023× 1023 sej in 2007 to 9.116× 1023sej in 2014, with 38% reduction on non-renewable emergy and 125% growth on imported emergy. Regional emergy money ratio (RMB) was reduced by 48% from 5.31× 1013sej/$ in 2007 to 2.74× 1013sej/$ in 2014, indicating that the increasing speed of consuming resources and energy was faster than the increase of GDP, and that Taiyuan’s money purchasing power declined. The lower emergy sustainability index (ESI) indicates that Taiyuan was explored and produced large quantities of mineral resources, which puts more stress on the environment as a consequence, and that this is not sustainable in the long run. The IPAT analysis demonstrates that Taiyuan sticks to the efforts of energy conservation and environmental protection, in order to promote regional sustainable development, it is necessary to take an integrated effort. Policy insights suggest that resourceful regions should improve include energy and resource efficiency, optimizing energy and resourceful structure.

Most empirical work on sources of economic growth for different countries lack country-specific empirical evidence to guide policy choices in individual developing countries and previous studies of factor productivity tend to focus on the entire economy or a single sector. In this study, we use the recently developed growth accounting tools to explicitly determine the sources of economic growth at both national and sectoral levels in Zambia between 1970 and 2013. We use data from World Development Indicators and Zambia’s Central Statistical Office. On average, total factor productivity (TFP) contributes about 5.7% to economic growth. Sectoral analysis shows that agriculture contributes the least to GDP and that within each sector; factors that contribute to growth differ. Structural transformation has been slow and contributed to the observed inefficiency. We outline the implications of the observed growth and provide recommendations.

The microstructural evolution, thermodynamics and kinetics of Mo-21%Tm₂O₃ (mass fraction, %) powder mixtures during ball milling were investigated using X-ray diffraction and transmission electron microscopy. Ball milling induced Tm₂O₃ to be decomposed and then dissolved into Mo crystal. The supersaturated nanocrystalline solid solution of Mo (Tm, O) was obtained after 96 h of ball milling. The elements of Mo, Tm and O were distributed uniformly in the ball-milled particles. Based on the semi-experimental theory of Miedema, a thermodynamic model was developed to calculate the driving force of phase evolution. There was no chemical driving force to form a crystal solid solution of Tm atoms in Mo crystal or an amorphous phase because the Gibbs free energy for both processes was higher than zero. For Mo-21%Tm₂O₃, it was mechanical work, not negative heat of mixing, that provided the driving force to form supersaturated nanocrystalline Mo (Tm, O) solid solution.

In this work, we consider a one-dimensional laminated beam in the case of non-equal wave speeds with only one infinite memory on the effective rotation angle. In this case, we establish the general decay result for the energy of solution without any kind of internal or boundary control. The main result is obtained by applying the method used in Guesmia et al. (Electron. J. Differential Equations 193: 1-45, 2012) and the second-order energy.

Human activities (e.g., exploitation, utilization, and conservation) exert substantial impact on forest ecological functions (FEF). The human influence on FEF significantly varies across developmental stages, which are attributed to the temporal and spatial in nature. This study evaluates some notable FEF indices (FEFI) in the 448 counties within the Yellow River basin (YRB) using panel data from the Seventh to Ninth National Forest Inventory. Data analysis involves employing the residual trends, geographical and temporal weighted regression. Results indicate that, firstly, the overall forest ecological function in the YRB is moderate to inferior, with superior FEF in counties endowed with more natural forest resources. Afforestation demonstrates a short-term improvement, but its effectiveness diminishes over time. Secondly, the positive spatial correlation is stronger among counties, characterized by both high-high and low-low agglomeration effects. Scattered planting, simple stand structure, and concentrated harvesting of forests at the identical stand ages hinder the formation of complex and large-scale FEF agglomerations. Thirdly, significant spatial-temporal differences exist in the impact of human activities on FEF. In the upper reaches of the basin, increased vegetation coverage through agricultural and forestry production benefited FEF, however, some over-exploitation of forests and grasslands is observed there. In the middle reaches, the economic development, expanding population and the greening activities help to improve FEF effectively, but excessive water using in agricultural production brought more difficulties to FEF improvement. In the lower reaches of the basin, improved wastelands and forest protection positively influence FEF. This study recommends that county governments should prioritize forest management with multi-species and multi-layered complex forests. Each county should define its position in regional development and ecological protection, considering the potential impacts on neighboring regions. This holistic approach promotes more effective integrated regional management.

The state detection of power cable is very important to ensure the reliability of power supply. Traditional sensors are mostly based on electric field detection, the operation is complex, and its efficiency needs to be improved. This paper optimizes the design and development of the magnetic field detection sensor for AC power cables. Firstly, through the establishment of the magnetic field sensor model, it is determined that permalloy is the material of the magnetic core, the optimal aspect ratio of the magnetic core is 20, and the ratio of coil length to core length is 0.3. Secondly, the coil simulation model is established, and it is determined that the optimal number of turns of the coil is 11000 turns, the diameter of the enamelled copper wire is 0.08mm, and the equivalent magnetic field noise of the sensor is 0.06pT. Finally, the amplifying circuit based on negative magnetic flux feedback is designed and the sensor is assembled, and the experimental circuit is built for sensitivity test. the results show that the sensitivity of the magnetic field sensor is 327.6mV/μT. The sensor designed in this paper has the advantages of small size, high sensitivity, easy to carry and high reliability.

This research, which focuses on wave energy generating technology, suggests a brand-new oscillating float-type wave energy conversion system that is appropriate for the offshore wave environment. To accurately model the device, a three-dimensional viscous numerical pool is created based on STAR-CCM+. The array-type power generation device is numerically simulated using theoretical analysis and numerical simulation, and the wave energy power generation device is arranged as double floats in the front and rear rows, representing triangular array type and rectangular array type, respectively. The triangular array type is a superior layout and can make greater use of marine resources, according to this paper's analysis of the hydrodynamic and power generation impacts of the three array types. The findings are meant to serve as a guide for engineering practice.

Origins of the time, mass, electric charges and magnetic monopoles are explained. The energies, electric charges and magnetic charges of the particles are defined as E = cDtDV and |q| = cDt = E/DV, and |q_m| = c²Dt, respectively, for the 3-D quantized spaces warped along the time axis direction of ct in the 4-D Euclidean space. The energy (or mass) and charges (or electric charges and magnetic charges) are the vectors along the time axis of ct in the 4-D Euclidean space. This new concept is closely connected to the wave function of the quantum mechanics. The electric charges, magnetic charges and energies have the property of the space direction independence. Magnetic monopoles (charges) are the force carrying bosons with the inside electric field time loop. Electric monopoles are the elementary fermions. Photon space fluctuations are explained with the quantized magnetic charges.

An analysis of the consistency of the Abraham and Minkowski momenta in the determination of the photon trajectory was carried out considering a new principle of conservation of the photon's mechanical energy, in which the photon conserves translational energy in orbital angular momentum when transiting between two media, introducing the relativistic energy wave (REW). The confrontation between REW and the recent theory of space-time waves (ST) was considered, pondering your differences. Throughout this study it was possible to verify that the Abraham momentum appears a relativistic photon ignition device in the transition between two media, acting as the hidden momentum of the Minkowski’s relativistic momentum. The wavy behavior in the matter is relativistic, and the relativistic trajectory appears with delays and advances, with points of synchronization between source-observer. The classical or relativistic trajectories are determined as a function of the angle of incidence and the relative refractive index, by one of two distinct non-additive torques, the classic by Abraham or the relativistic by Minkowski. It was found that the same analysis conducted under the principle of conservation of the mechanical energy of the photon can be treated by an new Doppler, Relativistic Apparent, that can be confused with other Dopplers in the treatment of redshift from distant sources. It was found that the conservation of energy in Orbital Angular Momentum (OAM), in the interaction with matter, explains that the synchronization instants are found in the inversion of the OAM, where the advances and delays of REW occur under negligible variations of the OAM, however, opposites.

Plants can utilize the different forms of nitrogen (N), including inorganic and organic N nutrients, and show the great difference in the utilizing efficiency of N-form among species and genotypes within a species. In our previous study, we found that Tibetan wild barley (XZ16) was better in utilization of organic nitrogen in comparison with cultivated barley (Hua30). In this study, metabolite profiles of the two barley genotypes were comprehensively compared in their response to four N forms, including nitrate (NO3-), ammonium (NH4+), urea and glycine. Macro-and micro-nutrient concentrations in shoots were mostly found higher in nitrate and urea treatments than in ammonium and glycine in both the genotypes. XZ16 had higher concentrations of nutrient ions in glycine treatment, but Hua30 accumulated more nutrients in ammonium treatment. Among the total 163 differentially expressed metabolites, highest up-regulation and highest down-regulation was found in XZ16 in glycine and urea treatments respectively. Some important metabolites such as proline, glutamine, serine, asparagine, L-homoserine, aspartic acid, putrescine, ornithine, 4-aminobutyrate were up-regulated in glycine treatment in both the genotypes with higher fold change in XZ16 than in Hua30. Similarly, fructose-6-PO4, aconitic acid and isocitrate were only up-regulated in XZ16 in glycine treatment. Here, we concluded that the genotype XZ16 exhibited higher response to glycine treatment, while Hua30 showed higher response to NH4+ treatment which is attributed to their better utilization of glycine-N and NH4+-N, respectively. .

Retiring coal power plants can reduce air pollution and health damages. However, the spatial distribution of those impacts remains unclear due to complex power system adjustments and pollution chemistry and transport. Focusing on coal retirements in Pennsylvania (PA), we analyze six counterfactual scenarios for 2019 that differ in retirement targets (e.g., reducing 50% of coal-based installed capacity vs. generation) and priorities (e.g., closing plants with higher cost, closer to Environmental Justice Areas, or with higher CO₂ emissions). Using a power system model of the PJM Interconnection, we find that coal retirements in PA shift power generation across PA and the Rest of PJM region leading to scenario-varying changes in the plant-level release of several air pollutants. Due to air pollution chemistry and transport and socio-demographics, these changes in turn give rise to a reduction of 10 to 182 PM_2.5-attributable deaths in PJM across the six scenarios, with most reductions occurring in PA. Scenarios that reduce more coal power generation yield greater aggregate health benefits due to air quality improvements in PA and adjacent downwind regions. In addition, vulnerable populations—in both PA and Rest of PJM—benefit most in scenarios that prioritize plant closures in PA near Environmental Justice Areas. These results demonstrate the importance of considering cross-regional linkages and socio-demographics in designing equitable retirement strategies.

The aim of this research work is to study the influence of temperature, solar irradiation and wind dust on the production of solar energy. In addition, it aims to study the assessment of water quality, in particular groundwater used for cooling and cleaning photovoltaic panels (quality analysis). it's an important source, stable and sustainable can be used entirely for cooling and cleaning PV modules from the sales dust, in order to improve their performance. To date, all research studies carried out in this context of cooling and cleaning using water have not taken account of the nature of this water. We have taken a sample of water from a well in a rural area in the Darra Tafilalet region of Morocco. This region has an arid and semi-arid climate, with very high temperatures and dust-laden winds, particularly in summer. These meteorological characteristics influence the efficiency of cells, particularly photovoltaic (PV) panels, reducing their performance. Next, the water sample was analysed in the laboratory. The results obtained show that the groundwater in this area is very sensitive to cooling and cleaning photovoltaic panels. Moreover, these results indicate that the temperature, solar irradiation and wind-blown dust have a significant influence on energy production.

Companies are increasingly focusing on sustainable business practices. Internal and external stakeholders’ expectations manifest in legal requirements, national and international standards, and market and customer expectations, among other things, must be considered. In addition to profit maximization as the usual target for corporate management, management must consider environmental sustainability aspects such as resource efficiency, greenhouse gas intensity, and a company's emissions behavior. In addition, social aspects relating to the company's employees, the immediate urban environment, the situation in the supply chain, and effects on the market environment must increasingly be considered. Specifically, companies are faced with the chal-lenge of dealing with conflicting objectives regarding the various aspects of sustainability and, if necessary, weighing them up against each other. These trade-offs must be made against the company's socio-economic and ecological environment, corporate strategy, and sustainability goals. This paper provides an overview of current approaches and research gaps on this topic through a literature review. It shows a lack of methods and frameworks to specifically deal with trade-offs and conflicts of goals.

In large-capacity energy storage systems, instructions are decomposed typically using an equalized power distribution strategy, where clusters/modules operate at the same power and durations. When dispatching shifts from stable single conditions to intricate coupled conditions, this distribution strategy inevitably results in increased inconsistency and hastened system aging. This paper presents a novel differentiated power distribution strategy comprising three control variables: the rotation status, the operating boundaries for both Depth of Discharge (DOD) and C-rates (C) within a control period. The proposed strategy integrates an aging cost prediction model developed to express the mapping relationship between these control variables and aging costs. Additionally, it incorporates the multi-colony particle swarm optimization (Mc-PSO) algorithm into the optimization model to minimize aging costs. The aging cost prediction model consists of three functions: predicting health features (HFs) based on the cumulative charge/discharge throughput quantity and operating boundaries, characterizing HFs as comprehensive scores, and calculating aging costs using both comprehensive scores and residual equipment value. Further, we elaborated on the engineering application process for the proposed control strategy. In the simulation scenarios, this strategy prolonged the service life by 14.62%, reduced the overall aging cost by 6.61%, and improved module consistency by 21.98%, compared with the traditional equalized distribution strategy. In summary, the proposed strategy proves effective in elongating service life, reducing overall aging costs, and increasing the benefit of energy storage systems in particular application scenarios.

In many developing countries, plastic waste management is left to citizens. This usually results in hazardous landfilling or open-air burning, leading to emissions that are harmful to human health and the environment. An easy, profitable, and clean method of processing and transforming the waste into value is required. In this context, this study provides an open-source methodology to transform low-density polyethylene drinking water sachets, into pavement blocks by using a streamlined do-it-yourself approach that requires only modest capital. Two different materials, sand, and ashes are evaluated as additives in plastic composites and the mechanical strength of the resulting blocks are tested for different proportion mix of plastic, sand, and ash. The best composite had an elastic modulus of 169MPa, a compressive strength of 29MPa, and a water absorptivity of 2.2%. The composite pavers can be sold at 100% profit while employing workers at 1.5X the minimum wage. In the West African region, this technology has the potential to produce 19 million pavement tiles from 28,000 tons of plastic water sachets annually in Ghana, Nigeria, and Liberia. This can contribute to waste management in the region while generating a gross revenue of 2.85 billion XOF (4.33 million USD).

Establishing an accurate mathematical model is the foundation of simulating the motion of marine vehicles and structures, and it is the basis of modeling-based control design. System identification from observed input-output data is a practical and powerful method. However, for modeling objects with different characteristics and known information, a single modeling framework can hardly meet the requirements of model establishment. Moreover, there are some challenges in system identification, such as parameter drift and overfitting. In this work, three robust methods are proposed for generating ocean hydrodynamic models based on Bayesian regression. Two Bayesian techniques, semi-conjugate linear regression and noisy input Gaussian process regression, are used for parametric and nonparametric gray-box modeling and black-box modeling. The experimental free-running tests of the KVLCC2 ship model and a multi-freedom wave energy converter (WEC) are used to validate the proposed Bayesian models. The results demonstrate that the proposed schemes for system identification of the ship and WEC have good generalization ability and robustness. Finally, the developed modeling methods are evaluated considering the aspects required conditions, operating characteristics and prediction accuracy.

The purpose of this paper is to examine the role and impact of public governance on European supranational public policies that seek to foster scientific and economic growth within innovation ecosystems (IEs) through the PITCCH initiative. The PITCCH is a European innovation development initiative funded by Horizon 2020 under the 'Innovation in SMEs' measure.The research methodology for this study is based on a 10-month real-time ethnographic field study of the PITCCH project, which allowed for the observation of the project governance and the capture of the perspectives of innovation-driven small and medium enterprises (i-SMEs) in their engagement with IE stakeholders.The findings of this research demonstrate the role of public governance in providing result-oriented practical support to the IE through the lens of i-SMEs, and they contribute to the existing literature on regional economic growth supported by supranational public policies. These findings have both academic and practical applications. They enrich the current literature on this topic and provide insights for policymakers and governing representatives seeking to implement effective public policies.

Quantifying different stocking rates effects in three study areas placed at Mediterranean forest (Cuenca, Spain) was conducted by applying a multiparametric soil quality index, SQI, developed in undisturbed forest soils (> 40 years). The main objective is to advance in the development and application of multiparametric indexes which allow for soil condition assessment. For it, is analyse the effectiveness of a multiparametric soil quality index (SQI) as an indicator livestock impacts on the soil in mediterranean forests. Control areas without stocking rates were compared in forest stands with different age (Thicket forest stand, < 30 years; High polewood forest stand, 30-60 years; Old growth forest stand, > 60 years); with various intensity grazing areas (permanent livestock passage: inactive sheepfold for 2-3 years, and active sheepfold; intermittent livestock passage: bare soil, pine stand, scrubland). The multiparametric soil quality index (SQI) applied sensitive to changes in forest ecosystems depending of different stocking rates. However, for even more preci-sion to assess cattle alteration, multiparameter index recalibrated, creating a new one; Soil Status Index by Livestock (SSIL). Correlation between quality ranges obtained with both indexes in dif-ferent study areas suggest that SSIL can be considered a livestock impact reference indicator in Mediterranean forest soils.

The current study was designed to investigate the anti-inflammatory effect of salidroside (SDS) and the underlying mechanism by using lipopolysaccharide (LPS)-stimulated RAW 264.7 macrophages in vitro and a mouse model of binge drinking induced liver injury in vivo. SDS downregulated protein expression of toll-like receptor 4 (TLR4) and CD14. SDS inhibited LPS-triggered phosphorylation of LPS-activated kinase 1 (TAK1), p38, c-Jun terminal kinase (JNK), and extracellular signal-regulated kinase (ERK). Degradation of IκB-α and nuclear translocation of nuclear factor (NF)-κB were effectively blocked by SDS. SDS concentration-dependently suppressed LPS mediated inducible nitric oxide synthase (iNOS) and cyclooxygenase-2 (COX-2) protein levels, as well as their downstream products, NO. SDS significantly inhibited protein secretion of interleukin (IL)-1β. Additionally C57BL/6 mice were orally administrated SDS for continuous 5 days, followed by three gavages of ethanol every 30 min. Alcohol binge drinking caused the increasing of hepatic lipid accumulation and serum transaminases levels. SDS pretreatment significantly alleviated liver inflammatory changes and serum transaminases levels. Further investigation indicated that SDS markedly decreased protein level of IL-1β in serum. Taken together, these data implied that SDS inhibits liver inflammation both in vitro and in vivo, and may be a promising candidate for the treatment of inflammatory liver injury.

Given the opportunities offered by foreign investment in energy infrastructure mostly by Chinese firms, the Government of Cambodia is giving high priority to developing hydropower resources for reducing energy poverty and powering economic growth. Using a “Political ecology of the Asian drivers” framework, this paper assesses China’s involvement in the development of large dams’ in Cambodia and its impacts on the access of natural resources such as water and energy by dam builders, local communities and the government. This analysis is based on 61 interviews and 10 focus group discussions with affected communities, institutional actors, Chinese dam builders and financiers in relation to the first large Chinese dam built in Cambodia, the Kamchay dam. Based on the results of the analysis this paper makes recommendations on how to improve the planning, implementation and governance of large dams to ensure that the dams’ benefits are shared more equally.

Here, satellite images from 2006 to 2022 were collected to assess changes in the sandbar topography of the Nakdong River Estuary region, southeast of South Korea. The employed method of satellite image acquisition involves capturing images at the same time each year to facilitate a comparison of topographical changes over time. The shorelines of the islands in the study area, including Jinwoo Island, Shinja Island, and Doyo Sandbar, were analyzed. Shoreline analysis was performed using the digital shoreline analysis system (DSAS) package in ArcGIS. The results indicate that Jinwoo Island is expanding at 6.46 m/year in the direction of Nulcha Island. The western side of Shinja Island is expanding at 4.76 m/year, whereas the eastern side is retreating at a rate of 24.41 m/year. In the case of the Doyo Sandbar, the southern shoreline is retreating at a rate of 14.69 m/year; however, the speed is gradually decreasing. Marked topographical changes are evident in the Nakdong River Estuary, and the interlinked barrier islands undergo deposition and erosion, leading to alterations in the shoreline. These findings serve as foundational data for predicting and addressing environmental and social issues arising in the Nakdong River Estuary region due to climate change.

In this article, we describe a simple procedure for evaluating the sterility of nutrient media using a shear-horizontal surface acoustic wave (SH-SAW) biosensor. We used the SH-SAW biosensor platform to monitor the time-dependent phase responses of the material for the media that binds to a monolayer of 3-mercaptopropanyl-N-hydroxy succinimide on the biosensor surface. Increases in the phase shift less than 50% of the starting phase shift recorded 180 minutes after the sterilization indicate a successful sterility test of the media. Our devices were then applied to sterility testing using a viable Escherichia coli (E. coli) K-12 solution to confirm our hypothesis. Filtered LB Broth was the negative control, and a 24-hour culture of E. coli was the positive control. Before testing, the cell solution was pelleted, the media decanted, and then replaced with a 1x phosphate-buffered saline solution (1x PBS). Since we know that the N-hydroxysuccinimide residues will bind to amine groups, only in cases where microbial species are present will the surface binding increase greater than 50%. We confirmed our hypothesis using SH-SAW biosensors and overnight E. coli cultures. The sensitivity for our 250 MHz quartz SH-SAW sensors was calculated based on the response from the E. coli K-12 solution over the linear dynamic range, which appears to be 2x10^4 – 2x10^7 CFU per ml and has a sensitivity of S = 1.655x10^5 o m2 Kg-1. The limit of detection (LOD) for these sensors was calculated to be approximately 2x10^-9 grams (g), which is estimated to be approximately 2,000 Escherichia coli (E. coli) K-12 cells. However, the sensitivity and insertion loss remained approximately unchanged before and after coating the sensor with 3,3'-Dithiobis(succinimidyl) Propionate (DSP).

In the era of mounting water scarcity, particularly in arid regions, the agricultural sector is striving to optimize the water resource management practices. Treated wastewater (TWW) has emerged as a viable alternative to freshwater for irrigation, offering a sustainable solution to water conservation. However, ensuring the safety and quality of TWW is paramount to safeguard for both crop health and environmental integrity. Electrical conductivity (EC), a critical factor in assessing TWW suitability for irrigation, can significantly impact crop yields and soil health since it is directly linked to the concentration of dissolved salts and ions. Therefore, this study delves into the development of advanced predictive models for EC assessment by employing supervised machine learning (ML) techniques like the Support Vector Regression (SVR), Adaptive Network-based Fuzzy Inference System (ANFIS), and Multiple Linear Regression (MLR). The TWW samples collected from Al-Qatif area, Saudi Arabia were assessed in the lab through a sensor-based real-time monitoring system integrated with Internet of Things (IoT) network and a multiprobe device. The key water quality parameters assessed involved, temperature (T), pH, Oxidation Reduction Potential (ORP), Resistivity (RES), Total Dissolved Solids (TDS), Salinity and Turbidity which served as the foundation for these models, given their profound influence on and their anticipated impact on EC levels. Following feature selection, two distinct model combinations were identified for the SVR, ANFIS and MLR models. Furthermore, to evaluate prediction performance, four statistical criteria, including coefficient of determination (R²), correlation coefficient (R), mean square error (MSE), and root mean square error (RMSE), were employed. Overall, the comparative performance results proved that ANFIS-M2 indicated the strongest predictive capability with the R² value of 0.99572 and 0.75145 and the RMSE values of 0.00965 and 0.01134, respectively in both calibration and verification stages.

Structural health monitoring has been studied by a number of researchers as well as various industries to keep up with the increasing demand for preventive maintenance routines. This work presents a novel method for reconstruct prompt, informed strain/stress responses at the hot spots of the structures based on strain measurements at remote locations. The structural responses measured from usage monitoring system at available locations are decomposed into modal responses using empirical mode decomposition. Transformation equations based on finite element modeling are derived to extrapolate the modal responses from the measured locations to critical locations where direct sensor measurements are not available. Then, two numerical examples (a two-span beam and a 19956-degree of freedom simplified airfoil) are used to demonstrate the overall reconstruction method. Finally, the present work investigates the effectiveness and accuracy of the method through a set of experiments conducted on an aluminium alloy cantilever beam commonly used in air vehicle and spacecraft. The experiments collect the vibration strain signals of the beam via optical fiber sensors. Reconstruction results are compared with theoretical solutions and a detailed error analysis is also provided.