The purpose of this project was to demonstrate the potential of converting an existing internal combustion engine for hydrogen operation at relatively low cost and to optimize the combustion process for ultra-low NOx emissions. The conversion has been carried out on a 450cc naturally aspirated single cylinder engine. The first baseline measurements and setup have shown lower NOx emissions than the baseline gasoline engine (without catalytic converter) for similar power output and engine efficiency. Further optimization of the combustion process allowed to achieve Euro VI and (latest European Commission proposal) Euro VII heavy-duty NOx limits without exhaust gas aftertreatment system (EATS) in steady state conditions. The concept is very promising and the knowledge gained should allow for further optimization to achieve near zero NOx emissions at high engine efficiency and power output with supercharging. It should also allow an efficient conversion of other engine types for different applications. In particular, a project with the aim to convert a heavy duty 6 cylinder engine intended for public transport buses has started. It follows a feasibility study which has shown the competitiveness of the hydrogen engine for this application.

In this work, we investigate the ability of a data assimilation technique and space-borne observations to quantify and monitor changes in nitrogen oxides (NOx) emissions over North-Western Greece for the summers of 2018 and 2019. In this region, four lignite-burning power plants are located. The data assimilation technique, based on the Ensemble Kalman Filter method, is employed to combine space-borne atmospheric observations from the high spatial resolution Sentinel-5 Precursor (S5P) Tropospheric Monitoring Instrument (TROPOMI) and simulations using the LOTOS-EUROS Chemical Transport model. The Copernicus Atmosphere Monitoring Service-Regional European emissions (CAMS-REG, version 4.2) inventory based on year 2015 is used as the a priori in the simulations. Surface measurements of nitrogen dioxide (NO2) from air quality stations operating in the region are compared with the model surface NO2 output using either the a priori (base run) or the a posteriori (assimilated run) NOx emissions. The high biases found between the in situ NO2 measurements and the base run surface NO2 decrease in the assimilated run in most cases. The bias in the station near the largest power plant decreases to 2.0 μg/m3 (2.83 μg/m3) from 10.5 μg/m3 (8.46 μg/m3) in 2019 (2018 respectively). Concerning the estimated annual a posteriori NOx emissions it was found that, for the pixels hosting the two largest power plants, the assimilated run results in emissions decreased by ~40-50% for 2018 compared to 2015, whereas a larger decrease, of ~70% for both power plants, was found for 2019, after assimilating the space-born observations. For the same power plants, the European Pollutant Release and Transfer Register (E-PRTR) reports decreased emissions in 2018 and 2019 compared to 2015 (-35% and -38% in 2018, -62% and -72% in 2019), in good agreement with the estimated emissions. We further compare the a posteriori emissions to the reported energy production of the power plants during the summer of 2018 and 2019. Mean decreases of about -35% and-63% in NOx emissions are estimated for the two larger power plants in summer of 2018 and 2019, respectively, which are supported by similar decreases in the reported energy production of the power plants (~-30% and -70%, respectively).

Creating accurate emission models capable of capturing the variability and dynamics of modern propulsion systems is crucial for future mobility planning. This paper presents a methodology for creating THC and NOx emission models for vehicles equipped with start-stop technology. A key aspect of this endeavor is to find techniques that accurately replicate the engine stop stages when there are no emissions. To this end, several machine learning techniques were tested using the Python programming language. Random forest and gradient boosting methods demonstrated the best predictive capabilities for THC and NOx emissions, achieving R2 scores of approximately 0.9 for both cold and hot engine emissions. Additionally, recommendations for effective modeling of such emissions from vehicles are presented in the paper.

Among the various types of gas sensors, the chemoresistive gas sensors based on metal oxides are considered the most attractive ones due to their simple operation, low costs and miniaturization. Thin films of V2O5 undoped and doped with TiO2 were studied as nitrogen dioxide, methane and hydrogen sensors. The experimental kinetics of the electrical conductivity changes due to introduction and removal of gas on metal oxide gas sensors were successfully explained in terms of the Langmuir adsorption theory.

Reactive NO_x is one of the major air pollutants, which also plays a key role as greenhouse gas. Many research efforts have been devoted to not only detection of NO_x in air but also abatement of NO_x emission. The aim of this mini review is to provide a panoramic snapshot of the electrochemical analysis methods for the emission and detection of NO_x in atmosphere, with special emphasis on NO_x sensor. The electrochemical detecting mechanism and materials for fabricating electrochemical gas sensors are discussed and the prospects and challenges in this area are also evaluated. This work will serve as a useful source to inform the interested audience of the latest developments and applications in the field of NO_x emission and electrochemical detection.

A method for accurately determining the chemical composition of deposits at the bottom of pores during the electrocoloring (e-coloring) of aluminum anodic oxide (AAO) layers in tin-based solutions is developed. The aluminum samples were AC e-colored after DC sulfuric anodization. Free-standing, tin e-colored aluminum oxide film was obtained by selective dissolution of the metallic aluminum from the AAO in copper chloride solution to access the deposit directly at the bottom of the pore. This allowed us to take XPS analysis directly from the deposits at pore bottoms without any interference from the base material or insulating barrier layer. The results revealed the presence of a mixture of tin oxide and metal in the deposits, which were richer in oxide content. Furthermore, a cyclic voltammetry experiment mimicking real polarization conditions during AC conditions was optimized and used to gain a deeper understanding of the electrochemical reactions that occur during AC electrocoloring. The comparison of CV results in tin-free and tin-containing electrolytes indicated that the tin deposited during a cathodic cycle is oxidized in the anodic cycle. The formation of tin based deposits radically changed the CV behavior. The XPS and cyclic voltammetry results consistently show that the deposits formed during e-coloring comprised a mixture of metallic and oxidic tin species richer in oxide content.

Soot combustion experiments with 5%O2/He were conducted using model soot, and four distinct compositions of CexPr1-xO2-δ oxides were prepared, varying nominal cerium com-positions (x=0, 0.2, 0.3, and 1). The catalyst samples were comprehensively characterized using techniques such as XRD, Raman spectroscopy, HR-TEM, N2 adsorption at −196 °C, XPS, O2-TPD, H2-TPR, and work function measurements. The Pr-rich compositions, rang-ing from Ce0.3Pr0.7O2-δ to PrO2-δ, resulted in a significant increase in the total evolved O2 amounts and enhanced catalyst reducibility. However, a decrease in textural properties of the catalysts was noted, being particularly important for the pure praseodymia under the synthesis route conducted. The catalytic activity was investigated under two contact modes of mixing between soot and catalyst: loose and tight. The results revealed that the catalytic performance is associated with the surface contact in tight contact mode and with the combination of surface/subsurface/bulk oxygen mobility and the BET surface ar-ea in loose contact mode. Notably, the T10 and T50 parameters were achieved at much lower temperatures than the uncatalyzed soot combustion, even under loose contact conditions. Specifically, the 50% conversion was achieved at 511℃ and 538℃ for Ce0.3Pr0.7O2 and Ce0.2Pr0.8O2, respectively. While no direct correlation between catalytic activity and work function was observed a significant relationship emerges between work function values and the formation of oxy-gen vacancies, whatever the conditions used for these measurements. On the other hand, the ability to generate a high population of oxygen vacancies at low temperatures, rather than the direct activation of gas-phase O2, influences the catalytic performance of Pr-doped ceria catalysts, highlighting the importance of surface/subsurface oxygen vacancy generation, which was the parameter which showed better correlation with the catalytic activity, whatever the soot conversion value or the mode of contact considered.

The article presents the results of studies aimed to identify the effect of foliar treatments of winter wheat, sugar beets and soybeans with mineral and bioorganic fertilizers. Their positive effect on increasing the concentration of mineral forms of nitrogen in soil was revealed. The crop types have a greater influence on the size of nitrous oxide emissions: in winter wheat crops - 679 µg/m3, soybeans - 637.2 µg/m3, sugar beets - 576.8 µg/m3. The amounts of nitrous oxide emissions were lower in the variants without the use of phosphorus-potassium fertilizers. The Ruter AA fertilizer showed the greatest efficiency on winter wheat crops - 42.7 c/ha. Soybean grain yield of 44.2 c/ha was also achieved by using Ruter AA, as well as Geo-humate together with phosphorus-potassium fertilizers. On the background of the actual supply of phosphorus and potassium, maximum yield was obtained when using N30 on the leaf - 39.3 c/ha. Foliar feeding ensured a yield of sugar beet root crops of up to 67.1-77.4 c/ha on the backdrop of the application of phosphorus-potassium fertilizers with the advantage of using Amino turbo. The largest yield of sugar beet roots without use of mineral phosphorus and potassium was ensured by N30 treatment of the leaf in the phases of 4-6 and 8 leaves - 63.2 t/ha. Of the organo-mineral fertilizers and biostimulants, the best result was shown by the use of Ruter A - 62.6 t/ha. We believe that foliar feeding of crops can be a sustainable farming method that can increase crop yields and reduce N2O emissions.

Moso bamboo is famous for fast growing and biomass accumulation, as well as high annual output for timber and bamboo shoots. These high outputs require high nutrient inputs to maintain and improve stand productivity. Soil nitrogen (N), phosphorus (P) and potassium (K) are important micronutrients for plant growth and productivity. Due to high variability of soils, analysing spatial patterns of soil N, P and K stocks is necessary for scientific nutrient management in Moso bamboo forests. In this study, soils were sampled from 138 locations across Yong’an City and ordinary kriging was applied for spatial interpolation of soil N, P and K stocks. Soil N stock showed a strong spatial dependence while soil N and P stocks presented a moderate spatial dependence, indicating soil N was mainly controlled by intrinsic factors while soil N and P stocks were controlled by both intrinsic and extrinsic factors. Different spatial patterns were observed for soil N, P and K stocks across the whole study area, indicating that fertilizations with different ratios of N:P:K should be applied for different sites to maintain and improve stand productivity. The total soil N, P and K stocks within 0-60 cm were 0.624, 0.020 and 0.583 Tg, respectively.

Ammonium sulfate has been utilized in agriculture; however, there is a dearth of research on its application in maize cultivation subsequent to the implementation of nitrification inhibitors or coating. This study aims to analyze the impacts of various combinations of ammonium sulfate fertilizers on soil nutrients, plant nutrient uptake, yield, and fertilizer utilization efficiency in maize cultivation to ascertain the optimal and stabilized disposal method for ammonium sulfate. A completely randomized design was employed with five treatments (AU, the control using urea; AS, treatment using ammonium sulfate; ASN, treatment using ammonium sulfate with a nitrification inhibitor; ASG, treatment using oil-coated ammonium sulfate; ASD, treatment using oil-humic acid-coated ammonium sulfate). Results showed that: (1) Compared with AU and AS, ASN, ASG and ASD decreased the leaching rates of TN, NH4+-N and NO3-N to the 10-20 cm soil layer, and more residual N was obtained in 0-10 cm soil layer. The first-order kinetic equation Nt=N0(1-e-kt) can better fit the process of nitrogen accumulation and release, and the N release rate constant is AU>CK>AS>ASH>ASN>ASD; (2) Compared with AU and AS treatments, the plant dry weight, grain dry weight, spike width, spike length, and yields of maize increased by 8.85-11.08%, 12.98-14.15%, 2.95-3.52%, 5.50-5.65%, and 43.21-51.10% under ASG treatment respectively. The impact of effective spike number on maize yield was found to be significant, as demonstrated by the path analysis conducted in this study. Furthermore, the accumulation levels of nitrogen, phosphorus, and potassium within above-ground plants significantly increased under the ASG treatment compared to the AU and AS treatments. The partial productivity of nitrogen, phosphorus, and potassium increased by 1.43-1.51-fold under ASG treatment, while grain nitrogen balance, grain phosphorus balance, and grain potassium balance increased by 1.41-1.58-fold, 1.51-1.95-fold, and 1.15-l.96-fold respectively. The oil-coated ammonium sulfate, therefore, exhibited the optimal slow-release effect of nutrients, thereby achieving superior performance in enhancing maize production and efficiency.

Nitrogen (N) is an essential macro nutrient for crop growth; therefore, N deficit can greatly limit crop growth and production. In the North China Plain (NCP), winter wheat is one of the main food crops, and its yield has increased from approximately 4000 kg ha-1 to 6000 kg ha-1 in the last two decades. Determining the proper N application rates at different growth stages and in all seasons is very important for the sustainable and high production of wheat in the NCP. A field experiment with five N application rates (250, 200, 150, 100, and 40 kgN·ha-1, designated as N250, N200, N150, N100, and N40, respectively) was conducted during the 2017-2018 and 2018-2019 winter wheat seasons to investigate the effects of the N application rate on water- and fertiliz-er-utilization efficiency, and on the crop growth and yield of winter wheat under sprinkler fer-tigation conditions. The results showed that, in the N application range of 40-200 kg ha-1, crop yield and water- and fertilizer-use efficiencies increased as the N application rate increased; however, further increases in the N application rate did not have additional benefits. The N up-take after regreening of winter wheat linearly increased with crop growth. Considering the wheat yield and N-use efficiency, the optimal N application range was 200 kg ha-1, and the best top-dressing strategy was equal amounts of N applied at the regreening, jointing, and grain-filling stages. The results of this study will be useful for optimizing field N management to achieve high wheat yield production in the NCP and in regions with similar climatic and soil environment conditions.

In this study, an attempt was made to investigate the Kenya case of multivariate causality of carbon dioxide emissions by employing a time series data spanning from 1961-2011 using the ARDL method of cointegration analysis. The long-run elasticities show that, a 1% increase in financial development increases carbon dioxide emissions by 0.28%, a 1% increase in GDP per capita increases carbon dioxide emissions by 1.32% and a 1% increase in urbanization decreases carbon dioxide emissions by 1.14%. There was a unidirectional causality running from financial development, food production index, GDP per capita, industrialization and urbanization to carbon dioxide emissions. The innovation accounting shows that 20% of future shocks in carbon dioxide emissions are due to fluctuations in financial development, 9% of future shocks in financial development are due to fluctuations urbanization and 22% of future shocks in food production index are due to fluctuations in carbon dioxide emissions.

Mass hauling operations play central roles in construction projects. They typically use many haulers that consume large amounts of energy and emit significant quantities of CO₂. However, practical methods for estimating the energy consumption and CO₂ emissions of such operations during project planning are lacking. This paper presents a detailed model for estimating the energy consumption and CO₂ emissions of mass haulers that integrates the mass hauling plan with a set of predictive equations. The mass hauling plan is generated using a planning program such as DynaRoad in conjunction with data on the productivity of selected haulers and the amount of material to be hauled during cutting, filling, borrowing, and disposal operations. This plan is then used as input for estimating the energy consumption and CO₂ emissions of the selected hauling fleet. The proposed model will help planners to assess the energy and environmental performance of mass hauling plans, and to select hauler and fleet configurations that will minimize these quantities. The model was applied in a case study, demonstrating that it can reliably predict energy consumption, CO₂ emissions, and hauler productivity as functions of the hauling distance for individual haulers and entire hauling fleets.

This study investigates the influence of adding hydrogen as an additive to gasoline in a four-stroke engine, utilizing a comprehensive thermodynamic comparative analysis conducted with self-developed engine model. The research aims to assess the performance, emissions, and efficiency of the engine when using gasoline-hydrogen blends, and to provide insights into the potential benefits of this approach. First the engine performance and emissions under different hydrogen blending levels were examined. A range of different air-to-fuel ratios (rich to lean) and varying percentages of hydrogen were considered. This systematic variation allowed for a detailed evaluation of the influence of hydrogen content on combustion efficiency, power out-put, and emissions characteristics. The analysis results included key parameters such as indicated specific fuel consumption and mean effective pressure. Additionally, the study focused on range prediction of nitrogen oxides (NOx) emissions, which are a critical environmental concern asso-ciated with internal combustion engines. The analysis of pressure and temperature profiles throughout the engine cycle shed light on the combustion characteristics and efficiency im-provements associated with hydrogen addition. In terms of emissions, the study projected that all emissions were reduced except NOx, which is highly dependent on hydrogen percentage, and it might be reduced in some cases, but with higher temperatures and pressures associated with hydrogen addition in most cases there is actually NOx increase, especially at higher engine loads.

This study aims to examine the non-volatile Particle Number (PN) emissions of a retrofitted Heavy-Duty Spark-Ignition (HD-SI) engine powered by liquefied petroleum gas (LPG) under both steady-state and transient conditions. The engine was tested under seven steady-state operating points to investigate the PN behavior and Particle Size Distribution (PSD) upstream and down-stream of the Three-Way Catalyst (TWC). This analysis intends to assess the impact of including particles with diameters ranging from 10 nm to 23 nm in the total particle count, a consideration for future regulations. The study employed the World Harmonized Transient Cycle (WHTC) for transient conditions to encompass the same engine working region used in the steady-state analysis. A Dekati FPS-4000 diluted the exhaust sample to measure the PSD and PN for particle diameters between 5.6 nm and 560 nm using the TSI-Engine Exhaust Particle Sizer (EEPS) 3090. Findings indicate that PN levels tend to increase downstream of the TWC under steady-state conditions in operating points with low exhaust gas temperatures and flows (equal to or less than 500 °C and 120 kg/h). Furthermore, the inclusion of particles with diameters between 10 nm and 23 nm leads to an increase in PN emissions by 17.70% to 40.84% under steady conditions and by an average of 40.06% under transient conditions, compared to measurements that only consider particles larger than 23 nm. Notably, in transient conditions, most PN emissions occur during the final 600 seconds of the cycle, linked to the most intense phase of the WHTC.

The spectra and global distributions of the X-ray emissions generated by the solar wind charge-exchange (SWCX) process in the terrestrial magnetosheath are investigated based on a global hybrid model and a global geocoronal hydrogen model. The solar wind O6+ ions which are the primary charge state for oxygen ions in solar wind are considered. The line emissivity of the charge-exchange born O5+ ions are calculated by Spectral Analysis System for Astrophysical and Lab oratory (SASAL). It is found that the emission lines from the O5+ ranges from 105.607 to 118.291 eV with the strong line at 107.047 eV. We then simulated the magnetosheath X-ray emission intensity distributions with a virtual camera at two positions of north pole and dusk at six stages during the passing of a perpendicular interplanetary shock combined with a tangential discontinuity structure through the Earth’s magnetosphere. During this process, the X-ray emission intensity increases with time, and the maximum value is 27.11 keV cm-2 s-1 sr-1 on the dayside, which is 4.5 times that before the solar wind structure reaches the Earth. A clear shock structure can be seen in the magnetosheath and moves earthward. The maximum emission intensity seen at dusk is always higher than that seen at north pole.

The study addresses the urgent environmental issue of climate change, focusing specifically on the role of local food, which is produced and consumed locally, helps reduce carbon emissions by eliminating the need for long-distance transportation. Through quantitative analysis, this study elucidates the potential benefits in environmental impact achieved through the consumption of local food: the significant reduction in carbon emissions. Specifically, the consumption of local food is found to yield an annual decrease of 2,421,296 tCO2 emissions, representing 2.5% of South Korea’s total greenhouse gas emissions from the transportation sector. This reduction further translates into an estimated economic value of USD 54.23 million (KRW 70.5 billion). This study underscores the potential of local food consumption as a tangible strategy to overcome environmental problems. Moreover, its academic contribution lies in its comprehensive analysis of the economic and empirical impacts of local food consumption on environment. Moving forward, we propose policies such as supporting local food distribution networks, providing public education on local food, fostering the local food industry, and providing incentives to revitalize local food consumption.

In recent years, many researchers have begun to shift their focus onto the synthesis of nanomaterials as this field possesses immense potential that may provide incredible technological advances in the near future. The downside of conventional synthesis techniques, such as co-precipitation, sol-gel and hydrothermal methods, is that they necessitate the use of toxic chemicals, produce harmful by-products and require a considerable amount of energy; therefore, more sustainable fabrication routes are sought after. Biological molecules have been previously utilised as precursors to nanoparticle synthesis, thus eliminating the negative factors involved in traditional methods. In addition, transition-metal nanoparticles possess a wide scope of applications due to their multiple oxidation states and large surface areas; thereby allowing for a higher reactivity when compared to their bulk counterpart and rendering them an interesting research topic. However, this field is still relatively unknown and unpredictable. Therefore, this review aims to obtain a better understanding on the plant-mediated synthesis process of the major transition-metal and transition-metal oxide nanoparticles, and how different parameters affect their unique properties.

This study presents the synthesis and electrochemical evaluation of nitrogen-doped vanadium oxide (N-V2O3/C) as a cathode material for aqueous zinc-ion batteries (AZIBs), using a hydrothermal method. Compared to undoped V2O3/C, N-V2O3/C exhibits enhanced electrical conductivity, capacity, and electrochemical kinetics, attributed to the incorporation of pyridinic and pyrrolic nitrogen. Initial charge-discharge cycles indicate phase transitions to amorphous vanadium oxides, enhancing conductivity. N-V2O3/C shows a high specific capacity of 168.4 mAh g−1 at 10 A g−1 and remarkable reversibility, highlighted by the transient existence of intermediate species during cycling. Optimal electrochemical performance is achieved with a vanadium to nitrogen molar ratio of 2:3, indicating the significant impact of nitrogen doping concentration on the material’s efficiency. This work underscores the potential of N-V2O3/C as a superior cathode material for AZIBs.

We study a two-echelon supply chain made up of a supplier and a manufacturer, both of which can reduce their component/product carbon emissions. With the vertical technology spillovers, we explore the optimal decisions of centralized and decentralized supply chains with price dependent demand and propose coordination strategy for the decentralized supply chain. Considering the cost contraction effectiveness of the technology spillovers, the centralized and decentralized game theoretic models of a two-echelon supply chain are developed to investigate optimal decisions of pricing and carbon emissions reduction. Through a systematic comparison and numerical analysis, we show that the profits of both players and the entire supply chain improve with the effect of technology spillovers increasing. Carbon emissions reduction will be taken by various protective measures so that the supplier and the manufacturer who do not innovate can hardly share the results of innovating via the “free-riding” methods when the technology spillover is relatively small. We also propose a revenue-cost sharing contract through bargaining to enhance the performance of the decentralized supply chain.

Oxidative stress-mediated damage is often a downstream result of Parkinson’s disease (PD), which is marked by sharp decline in dopaminergic neurons within the nigrostriatal regions of the brain, accounting for the symptomatic motor deficits in patients. Regulating the level of oxidative stress may present a beneficial approach in preventing PD pathology. Here, we assessed the efficacy of a nicotinamide adenine phosphate (NADPH) oxidase (NOX) inhibitor, an exogenous reactive oxygen species (ROS) regulator synthesized by Aptabio therapeutics with the specificity to NOX-1, 2, and 4. Utilizing N27 rat dopaminergic cells and C57Bl/6 mice, we confirmed that the exposures of alpha-synuclein preformed fibrils (PFF) induced protein aggregation, a hallmark in PD pathology. In vitro assessment of the novel compound revealed an increase in cell viability and decreases in cytotoxicity, ROS, and protein aggregation (Thioflavin-T stain) against PFF exposure at the optimal concentration of 10nM. Concomitantly, the oral treatment alleviated motor deficits in behavioral tests, such as hindlimb clasping, rotarod, pole, nesting, and grooming test, via reducing protein aggregation, based on rescued dopaminergic neuronal loss. The suppression of NOX-1, 2, and 4 within the striatum and ventral midbrain regions including SNc contributed to neuroprotective/recovery effects, making it a potential therapeutic option for PD.

Cardiac aging is characterized by alterations in contractility and intracellular calcium ([Ca²⁺]_i) homeostasis. It has been suggested that oxidative stress may be involved in this process. We and others have reported that in cardiomyopathies the NADPH oxidase (NOX)-derived superoxide is increased, with a negative impact on [Ca²⁺]_i and contractility. We tested the hypothesis that in the aged heart, [Ca²⁺]_i handling and contractility are disturbed by NOX-derived superoxide. Contractility was evaluated isolated hearts, challenged with isoproterenol. To assess [Ca²⁺]_i, isolated cardiac myocytes were field-stimulated and [Ca^2+]_i was monitored with fura-2. Cardiac concentration-response to isoproterenol was depressed in aged compared to adults hearts (p < 0.005), but was restored by NOX inhibitors apocynin and VAS2870. In isolated cardiomyocytes, apocynin increased the amplitude of [Ca²⁺]_i in aged myocytes (p < 0.05). Time-50 [Ca²⁺]_i decay was increased in aged myocytes (p < 0.05) and reduced towards normal by NOX inhibition. In addition, we found that myofilaments Ca²⁺ sensitivity was reduced in aged myocytes (p < 0.05), and further reduced by apocynin. Finally SERCA levels but not phospholamban were reduced in aged hearts (p < 0.05). In conclusion, β-adrenergic‒induced contractility was depressed in aged hearts, and NOX inhibition restored back to normal. Moreover, altered Ca²⁺ handling in aged myocytes was also improved by NOX inhibition. These results suggest a NOX-dependent effect in aged myocytes at the level of Ca²⁺ handling proteins and myofilaments.

Agricultural activities are the second largest source of greenhouse gas emissions, and carbon emissions from agricultural land use (CEALU) have become a hot issue across the world. However, few scholars explored the impact of agricultural land policies on carbon emissions, such as the High-standard farmland construction(HSFC) in China.Thus，by relying on provincial panel data for China for the period 2005-2017, the effect of the high-standard basic farmland construction policy on carbon emissions from agricultural land use per unit area and its regional differences were quantitatively analyzed using the difference-in-difference (DID) model. The results showed that: 1) China's CEALU per unit area presented a fluctuating upward trend during the period 2005-2017, from 392.58 kg/ha to 457.72 kg/ha, with an average annual growth rate of 1.31%. 2) The high-standard farmland construction(HSFC) policy produced a significant carbon emission reduction effect in agricultural land use, and reduced the CEALU per unit area by 10.80% on average. With the promotion of this policy, its carbon emission reduction effect in agricultural land use presented an overall increasing trend. 3) The carbon emission reduction effect of the high-standard farmland construction policy in agricultural land use was significant in central China, but non-significant in eastern China and western China.

Agriculture (crop production, land use, and livestock) is the second most important greenhouse gas (GHG) emitting sector after the energy sector. Agriculture is also recognized as the source and sink of GHGs. Evidence demonstrates that the application of high amounts of nitrogen-rich fertilizers enhances methane (CH4) and nitrous oxide (N2O) emissions, which are potent GHGs with a high global warming potential (GWP). Considering its global contribution to the climate crisis, reducing GHG emissions in agriculture would considerably lower its share of the global GHG emission records, which may lead to enormous benefits for the environment and food production systems. Several diverging and controversial views questioning the actual role of plants in the current global GHG budget continue to nourish the debate globally. We must acknowledge that considering the beneficial roles of major GHGs to plants at a certain level of accumulation, implementing GHG mitigation measures from agriculture is indeed a complex task. This review seeks to provide key approaches for GHG mitigation in the literature (environmentally friendly crop cultivation and residue management practices, improvement of plants nutrients/fertilizer use efficiency, exploring the genetic diversity for low GHG emission, soil methane-producing bacteria, integrated soil fertility management, improved livestock feeding efficiency, and production, etc.). This work gathers key approaches from 275 peer-reviewed publications, including experimental research papers, review articles, and books, discussing greenhouse gas emissions mechanisms and mitigation to unravel effective strategies for GHG mitigation, proven to be effective or carry the potential to mitigate GHG generation from agriculture. This review also discusses in depth the significance and the dynamics of strategies regarded as game changers with a high potential to enhance, in a sustainable manner, the resilience of agricultural systems. Agricultural GHG mitigation approaches discussed in this work can serve as game changers in global efforts to reducing GHG emissions and alleviating the impact of climate change through sustainable agriculture and informed-decision making.

The expanding global population has increased the demand for sustainable protein sources, and microbial protein (MP) has emerged as a promising alternative. However, conventional carbon (glucose) and nitrogen (ammonia, urea) sources needed for MP production pose environmental and economic issues. This study aims to produce protein using lignocellulosic biomass (LCB) as a carbon source and the nitrogen fixation ability of Klebsiella oxytoca M5A1 as a nitrogen source. The study investigates the pretreatment of LCB (switchgrass), enzymatic hydrolysis, protein quantification, and high-performance liquid chromatography system (HPLC) analysis to track glucose utilization and organic acid production. K. oxytoca M5A1 harnessed free nitrogen from the atmosphere through nitrogen fixation and used abundant, cheap glucose from LCB to produce MP and organic acids as by-products. Protein production occurred in two phases: first within the initial 8 hours and secondly, within the last 16 hours. The highest protein concentration was at 40 hours, with approximately 68.3% protein content. HPLC analysis revealed a dynamic profile of glucose utilization and organic acids (Lactic acid, Propionic acid, Acetic acid, and Succinic acid). K. oxytoca M5A1 exhibited an early high rate of glucose consumption, and conversion to organic acids that were later used for second-phase protein production. The acids profile revealed intra-conversion from one acid to another via metabolic pathways (glycolysis and tricarboxylic acid cycle). Overall, leveraging LCB and the nitrogen-fixing ability of K. oxytoca M5A1 for MP production offers an eco-friendly and cost-effective alternative to traditional protein sources, contributing to a sustainable circular economy.

Urbanization is considered as a main indicator of regional economic development due to its positive effect on promoting industrial development; however, many regions, especially developing countries, are troubled by its negative effect — the aggravating environmental pollution. Many researchers have indicated that rapid urbanization stimulated the expansion of industrial production scale and increased industrial pollutant emissions. However, this judgement contains a grave deficiency in that urbanization not only expands industrial production scales but can also increase industrial labour productivity and change the industrial structure. To modify this deficiency, we first decompose the influence which urbanization impacts on industrial pollutant emissions into the scale effect, the intensive effect and the structure effect by using the Kaya Identity and the LMDI Method; second, we perform an empirical study of the three effects’ impacts by applying the spatial panel model with data from 282 Chinese cities between 2003 and 2013. Our results indicate that (1) there are significant reverse U-shapes between Chinese urbanization rate and its industrial pollutant emissions; (2) the scale effect and the structure effect have aggravated Chinese industrial waste water discharge, sulphur dioxide emissions and soot (dust) emissions, while the intensive effect has generated a decreasing and ameliorative impact on that aggravated trend. The definite relationship between urbanization and industrial pollutant emissions depends on the combined influence of the scale effect, the intensive effect and the structure effect; (3) there are significant spatial autocorrelations of industrial pollutant emissions between Chinese cities, but the spatial spillover effect from other cities does not aggravate local urban industrial pollutant emissions, we offer an explanation to this contradiction that the vast rural areas surrounding Chinese cities have served as sponge belts and have absorbed the spatial spillover of cities’ industrial pollutant emissions. According to the results, we argue that this type of decomposition of the influence into three effects is necessary and meaningful, it establishes a solid foundation for understanding the relationship between urbanization and industrial pollutant emissions, and effectively helps to meet relative policy making.

Studies on N balance due to N inputs and outputs and soil N retention to measure cropping system performance and environmental sustainability are limited due to the complexity of measurements of some parameters. We measured N balance based on N inputs and outputs and soil N retention under dryland agroecosystem affected by cropping system and N fertilization from 2007 to 2011 in the northern Great Plains, USA. Cropping systems were conventional tillage barley (Hordeum vulgaris L.)-fallow (CTB-F), no-tillage barley-fallow (NTB-F), no-tillage barley-pea (Pisum sativum L.) (NTB-P), and no-tillage continuous barley (NTCB). Nitrogen rates to barley were 0, 40, 80, and 120 kg N ha-1. Total N input due to N fertilization, pea N fixation, soil N mineralization, atmospheric N deposition, nonsymbiotic N fixation, and crop seed N and total N output due to grain N removal, denitrification, volatilization, N leaching, gaseous N (NOx) emissions, surface runoff, and plant senescence were 28 to 37% greater with NTB-P and NTCB than CTB-F and NTB-F. Total N input and output also increased with increased N rate. Nitrogen sequestration rate at 0 to 10 cm averaged 22 kg N ha-1 yr-1 for all treatments. Nitrogen deficit ranged from 5 to 16 kg N ha-1 yr-1, with greater deficits for CTB-F and NTB-P and higher N rates. Because of increased grain N removal and reduced N loss to the environment and N fertilizer requirement, NTB-P with 40 kg N ha-1 can enhance agronomic performance and environmental sustainability while reducing N inputs compared to other management practices.

In this study, the causal-effect between carbon dioxide emissions and forestry production and trade was investigated in Ghana by employing a data spanning from 1961 to 2014 by using the VECM and ARDL model. Evidence of the long-run equilibrium relationship in the VECM shows that, a 1% increase in veneer sheet production reduces carbon dioxide emissions by 1.47% in the long-run. There was evidence of a bidirectional causality between carbon dioxide emissions and veneer sheet production, carbon dioxide emissions and wood charcoal production, and a unidirectional causality running from carbon dioxide emissions to wood fuel production and plywood production to carbon dioxide emissions. Evidence from the long-run equilibrium relationship in the ARDL model shows that; a 1% increase in plywood production will increase carbon dioxide emissions by 0.17% in the long-run, a 1% increase in sawnwood production will increase carbon dioxide emissions by 0.17% in the long-run, a 1% increase in wood charcoal production will increase carbon dioxide emissions by 0.36% in the long-run and a 1% increase in wood fuel production will increase carbon dioxide emissions by 0.37% in the long-run.

In this study, long-term mortality effects associated with exposure to PM10, PM2.5, BC (black carbon), and NOx were analyzed in a cohort in southern Sweden during the period from 1991‒2016. Participants (those residing in Malmö, Sweden, born between 1923‒1950) were randomly recruited from 1991‒1996. At enrollment, 30,438 participants underwent a health screening, which consisted of questionnaires about lifestyle and diet, a clinical examination, and blood sampling. Mortality data were retrieved from the Swedish national cause of death register. The modeled concentrations of PM10 (particles with an aerodynamic diameter smaller than or equal to 10 µm), PM2.5 (particles with an aerodynamic diameter smaller than or equal to 2.5 µm), BC (black carbon), and NOx (nitrogen oxides) at the cohort participants' home addresses were used to assess air pollution exposure. Cox proportional hazard models were used to estimate the associations between long-term exposure to PM10, PM2.5, BC, and NOx and the time until death among the participants during the period from 1991‒2016. The hazard ratios (HRs) associated with an interquartile range (IQR) increase in each air pollutant were calculated based on the exposure lag windows of the same year (lag0), 1‒5 years (lag1‒5), and 6‒10 years (lag6‒10). Three models were used with varying adjustments for possible confounders including both single-pollutant estimates and two-pollutant estimates. With adjustments for all covariates, the HRs for PM10, PM2.5, BC, and NOx in the single-pollutant models at lag1‒5 were 1.06 (95% CI: 1.02‒1.11), 1.01 (95% CI: 0.95‒1.08), 1.07 (95% CI: 1.04‒1.11), and 1.11 (95% CI: 1.07‒1.16) per IQR increase, respectively. The HRs were in most cases decreased by the inclusion of a larger number of covariates in the models. The most robust associations were shown for NOx, with statistically significant positive HRs in all models. An overall conclusion is that road traffic-related pollutants had a significant association with mortality in the cohort.

One of the most concerning global environmental issues is the pollution of agricultural soils by heavy metals (HMs), especially cadmium (Cd), which not only affects human health by taking Cd-containing foods but also impacts the quality of rice. The soil's nitrification and denitrification processes, coupled with the release of volatile organic compounds by plants, raise substantial concerns. The understanding of three aspects of paddy soil under conditions of heavy-metal pollution and water management is currently limited. In this review, we summarized recent literature related to the deleterious effects of Cd on both soil processes related to the N cycle and rice quality, particularly aroma, in different water management practices. Under both continuous flooding (CF) and alternate wetting and drying (AWD) conditions, cadmium (Cd) has been observed to reduce both nitrification and denitrification processes. The adverse effects are more pronounced in continuous flooding (CF) compared to alternate wetting and drying (AWD). Similarly, the alteration in rice aroma is more significant in AWD than in CF. The precise modulation of volatile organic compounds (VOCs) by Cd, remains unclear based on the available literature. Nevertheless, HM accumulation is higher in AWD conditions compared to CF, leading to a detrimental impact on volatile organic compounds (VOCs). The literature concluded that AWD practices should be avoided in Cd contaminated fields to decrease accumulation and maintain the quality of rice. In the future, rhizospheric engineering and plant biotechnology can be used to decrease the transport of HMs from the soil to the plant’s edible parts.

Iron oxide nanoparticles have been investigated due to their suitable characteristics for diverse applications in the fields of biomedicine, electronics, water/wastewater treatment and sensors. Maghemite, magnetite and hematite are the most widely studied iron oxide particles and have ferrimagnetic characteristics. When very small, however, these particles have superparamagnetic properties and are called superparamagnetic iron oxide nanoparticles (SPIONs). Several methods are used for the production of these particles, such as coprecipitation, thermal decomposition and microemulsion. However, the variables of the different types of synthesis must be assessed to achieve greater control over the particles produced. In some studies, it is possible to compare the influence of variations in the factors for production with each of these methods. Thus, researchers use different adaptations of synthesis based on each objective and type of application. With coprecipitation, it is possible to obtain smaller, more uniform particles with adjustments in temperature, pH and the types of reagents used in the process. With thermal decomposition, greater control is needed over time, temperature as well as the proportion of surfactants and organic and aqueous phases in order to produce smaller particles and a narrower size distribution. With the microemulsion process, the control of the confinement of the micelles formed during synthesis through the proportions of surfactant and oil makes the final particles smaller and less dispersed. These nanoparticles can be used as additives for the creation of new materials, such as magnetic bacterial cellulose, which has different innovative applications. Composites that have SPIONs, which are produced with greater rigour with regards to size and distribution, have superparamagnetic properties and can be used in medical applications, whereas materials containing larger particles have ferromagnetic applications. To arrive at a particular particle with specific characteristics, researchers must be attentive to both the mechanism selected and the production variables to ensure greater quality and control of the materials produced.

In this article we review the advances that have been made on the understanding of the high-pressure structural, vibrational, and electronic properties of wolframite-type oxides since the first works in the early 1990s. Mainly tungstates, which are the best known wolframites, but also tantalates and niobates, with an isomorphic ambient-pressure wolframite structure, have been included in this review. Apart from estimating the bulk moduli of all known wolframites; the cation-oxygen bond distances and their change with pressure have been correlated with their compressibility. The composition variations of all wolframites have been employed to understand their different structural phase transitions to post-wolframite structures as a response to high pressure. The number of Raman modes and band gap energy changes have been also analyzed in the basis of these compositional differences. The reviewed results are relevant for both fundamental science and for the development of wolframites as scintillating detectors. The possible next research venues of wolframites have also been evaluated.

The review analyzes the studies published mainly in the last 10-15 years, on the synthesis, structure, and sensor properties of semiconductor nanocomposites. Particular attention is paid to the interaction between nanoparticles of the sensitive layer and its effect on the structure, sensitivity, and selectivity of semiconductor sensor systems. Various mechanisms are considered of interaction between nanoparticles in metal oxide composites including incorporation of metal ions of one component into the structure of another, heterocontacts between different nanoparticles, and core-shell systems, as well as their influence on the characteristics of gas sensors. The experimental data and studies on the modeling of charge distribution in semiconductor nanoparticles, which determine the conductivity and sensor effect in one- and two-component systems, are also discussed. It is shown that the model which considers the interactions of nanoparticles best describes the experimental results. Some mechanisms of detection selectivity are considered in the conclusion.

For thermoelectric materials study and development, it is very important to measure the electrical power and efficiency of a thermoelectric generator (TEG). In this study, thermoelectric properties such as electrical conductivity, Seebeck coefficient, and thermal conductivity of cement composites with graphene nanoplatelets and metallic oxides (Fe2O3, ZnO, MnO2) are measured and subsequently used to figure out the output electrical power and efficiency. A maximum of 1.5 W power per square meter for a temperature difference of about 50 °C can be estimated using GnP-ZnO added cement composites. This paper also talks about how to make a cement composite-based structural TEG module to enhance the total output voltage, power, and efficiency of the system.

Knowledge about the formation energies of compounds is essential to derive phase diagrams of multi-component phases with respect to elemental reservoirs. The determination of formation energies using common (semi-)local exchange-correlation approximations of density functional theory (DFT) exhibits well-known systematic errors if applied to oxide compounds containing transition metal elements. In this work, we generalize, reevaluate and discuss a set of approaches proposed and widely applied in the literature to correct for errors arising from the over-binding of the O2 molecule and from correlation effects of electrons in localized transition-metal orbitals. The DFT+U method is exemplarily applied to iron oxide compounds, and a procedure is presented to obtain U values, which lead to formation energies and electronic band gaps comparable to experimental values. Using such corrected formation energies, we derive the phase diagrams for LaFeO3, Li5FeO4 and NaFeO2, which are promising materials for energy conversion and storage devices. A scheme is presented to transform the variables of the phase diagrams from the chemical potentials of elemental phases to those of precursor compounds of a solid-state reaction, which represents the experimental synthesis process more appropriately. The discussed workflow of methods can directly be applied to other transition metal oxides.

Coal-fired thermal plants (CTPP) are known to pollute the atmosphere with emission of many greenhouse gases and particulate matter. The power generation from these thermal plants cannot be stopped completely because it forms the backbone of the grid power supply. It is necessary to study the dispersion patterns of pollutants that affect the health of the people. The dispersion patterns are location specific since they depend on local meteorological conditions. In this study, the dispersion of particulate matter (PM) and sulphur dioxide (SO₂) from a CTPP with 275 m high stack are studied under different atmospheric boundary layer (ABL) of neutral, stable and unstable conditions up to a distance of 30 km from the stack. The plume of the PM spreads under all conditions. During some parts of the day, PM settles around the stack while at other times PM keeps suspending in the air for the full distance under study. Sulphur dioxide dilutes to concentrations below the detection limits in about 12-13 km from the stack for neutral and unstable ABL whereas for the stable ABL, the dispersion is up to 30 km. The 24 h weighted average concentration of sulphur dioxide, at 10 m height from the ground, is 14.2 mg/m³ at a distance of 25 kms from the CTPP, which is comparable with the value of 9.2 mg/m³ measured at the Air Quality Stations located around the same distance. Based on the results policy changes that need to be implemented are suggested.

We monitored the water quality and hydrological conditions of a horizontal subsurface constructed wetland (HSSF-CW) in Beijing, China, for 2 years. We simulated the area rate constant and the temperature coefficient with the first-order kinetic model. We examined the relationships between the nitrogen (N) removal rate, N load, seasonal variations in the N removal rate, and environmental factors, such as the area rate constant, temperature, and dissolved oxygen (DO). The effluent ammonia (NH₄⁺-N) and nitrate (NO₃⁻-N) concentrations were significantly lower than the influent concentrations (p<0.01, n=38). The NO₃⁻-N load was significantly correlated with the removal rate (R²=0.9566, p<0.01), but the NH^₄+-N load was not correlated with the removal rate (R²=0.0187, p>0.01). The area rate constants of NO₃⁻-N and NH₄⁺-N at 20 °C were 27.01±26.49 and 16.63±10.58 m∙yr⁻¹, respectively. The temperature coefficients for NO₃⁻-N and NH₄⁺-N were estimated at 1.0042 and 0.9604, respectively. The area rate constants for NO₃⁻-N and NH₄⁺-N were not correlated with temperature (p>0.01). The NO₃⁻-N area rate constant was correlated with the corresponding load (R²=0.9625, p<0.01). The NH₄⁺-N area rate was correlated with DO (R²=0.6922, p<0.01), suggesting that the factors that influenced the N removal rate in this wetland met Liebig's law of the minimum.

An effective method for coating textile fabrics with porous materials is proposed, and the removal rates of nitrogen oxides (NOx), sulfur oxides (SOx), and fine dust particles in the coated textile fabrics are evaluated. The textile fabrics made of polyester are used to effectively reduce fine dust particles through static electricity. Zeolite and coconut shell activated carbon are used as porous material to reduce SOx and NOx, respectively. The effects of the epoxy content and dilution solution types on the SOx removal rate of textile fabrics coated with zeolite are evaluated to determine the optimum coating conditions. In addition, the effects of external environmental conditions, such as washing and freeze thawing, on the SOx and NOx removal rates of the textile fabrics coated with porous materials using the optimum coating conditions are examined. The test results show that the SOx removal rate of textile fabrics coated with zeolite decreases with the increase in the epoxy content. The decrease is 2.9 times larger for textile fabrics coated using deionized water than those coated using isopropyl alcohol. After one wash, the SOx removal rate decreases dramatically. However, the decrease is reduced by 16% when the epoxy content ratio is increased by 0.5%. The effects of washing and freeze thawing on the SOx and NOx removal rates of textile fabrics coated using the deionized water diluted with the epoxy content ratio of 2% are minimal. Consequently, to maintain stable SOx and NOx removal rates under external environmental conditions such as washing and freeze thawing, 98% deionized water dilution and 2% epoxy content ratio are required for the optimum coating of textile fabrics with zeolite and coconut shell activated carbon.

A 2-month incubation study was carried out using two soil types to determine nitrogen mineralization of different inorganic-organic amendments. The following seven treatments (T) were established; T1 = control, T2 = 5 g of dry algae per kg of soil (100%DA), T3 = 136g of agri-mat per kg of soil (100%GA), T4 = 61 g of ground grass per kg of soil (100%GG), T5 = 2.5 g of dry algae + 2.5 g of nitrogen fertilizer (NF) per kg of soil (50%DA50NF), T6 = 50%GA50NF, T7 = 50%GG50NF. Three samples per treatment were drawn at 0, 3, 7, 15, 30, 45, and 60 days for mineral-N determination. A 2-month glasshouse experiment was established afterwards with the following five treatments: T1 = Control, T2 = 50%DA, T3 = 50%GA, T4 = 50%GG, and T5 = 100NF. The results indicated that nitrogen mineralization was significantly higher in organic-inorganic amendments compared to sole organic amendments. The percentage differences ranged from 157% to 195%. The 50%DA treatment increased spinach yield by 20.6% in sandy loam and 36.5% in loam soil. It is difficult to fully recommend the 50%DA treatment without field-scale evaluation, but it is a promising option to be considered.

Conventional fertilization practices can lead to many ecological problems, such as nutrient imbalance, soil acidity, and reduced soil fertility in natural rubber plantations. To address these challenges, a field investigation was strategically carried out to substitute inorganic fertilizer with organic fertilizers consisted of six treatments, i.e., no fertilization (CK), inorganic fertilizer (NPK), 25 % replacement of inorganic through organic (25%M), 50 % replacement of inorganic through organic (50%M), 75 % replacement of inorganic through organic (75%M), and 100% organic fertilizer (100%M). The soil physicochemical properties (SOC, TN, AN, C:N, pH, NH4+-N, and NO3--N) and carbon and nitrogen converting enzymes (BG, NAG, and LAP) were all determined. The partial substitution of inorganic fertilizers with organic fertilizers (i.e., 75%M at surface soil layer) showed higher SOC (14.52 g.kg-1), TN (1.06 g.kg-1), AN (20.07 mg.kg-1), C:N (14.63), NH4+-N (10.63 mgkg-1), and NO3--N(11.06 mg.kg-1) than NPK and CK. Such increase in physicochemical properties in partial replacement of inorganic with organic fertilizers plots resulted from higher carbon and nitrogen enzymes activities (BG (143.17 nmol.g-1.h-1), NAG (153.96 nmol.g-1.h-1), and LAP (153.48 nmol.g-1.h-1)) compared to NPK and CK, and further the person correlation and RDA analysis confirmed a significant positive correlation between SOC, AN, and soil enzymes. This study presents a new strategy for assessing the impact of partially replacing inorganic fertilizers with organic fertilizers in rubber plantations, mainly by modifying the soil nutrient composition in tropical regions.

The substitution of chemical fertilizers by organic manure plays a critical role in sustainable crop production. Nevertheless, organic amendments promote the global warming potential (GWP) in rice paddies due to increased methane (CH4) emissions. Increasing evidence shows that lime application can reduce CH4 emissions from acidic paddy soils, while it is still not clear whether liming can reduce the GWP in rice fields under organic manure substitution. A two-year field experiment was conducted to investigate the impacts of pig manure substitution and lime application on grain yield, CH4 and nitrous oxide (N2O) emissions in a subtropical double-cropped rice field in China. The experiment consisted of three treatments: chemical fertilization (CF, 100% N from urea), 50% of chemical N substituted by pig manure (1/2N + M), and the 1/2N + M treatment plus lime amendment (1/2N + M + L). On average, 1/2N + M reduced rice yield by 5.65% compared to CF, while lime application had no effect on rice yield. Mean cumulative CH4 emissions were 218.8% higher in 1/2N + M than in CF, whereas 1/2N + M + L reduced CH4 emissions by 36.6% compared to 1/2N + M. Neither pig manure substitution nor lime application affected N2O emissions. Consequently, 1/2N + M increased the GWP and greenhouse gas intensity (GHGI) by 214.6% and 228.3%, respectively, compared to CF. In contrast, 1/2N + M + L reduced the GWP and GHGI by 36.4% and 36.5% compared to 1/2N + M. Lime application can mitigate CH4 emissions and GWP induced by pig manure amendment in double-cropped rice fields.

Arsenic is highly toxic, affecting millions of people in many regions of the world. That is why developing economic and efficient technologies is imperative to eliminate it. Sorption techniques are attractive as efficient and inexpensive sorbents can be used. Chitosan is an abundant, naturally occurring, biodegradable, low-cost biopolymer that can be combined with metal oxide to enhance its removability. This work aimed to synthesize a new chitosan-magnetite-based sorbent for arsenic removal. The synthesized sorbent does not present pores, and by FT-IR, functional groups of the chitosan and the presence of As(V) in the sorbent treated with arsenic were identified. The synthesized magnetite was characterized by XRD spectroscopy. Application of the Composite Central Design model showed that 0.22 g of the sorbent at pH 6.0 could remove 27.6% of As(V). Kinetic data, fitted with the pseudo-first and second-order models, indicated an ion exchange sorption and activation energy of 28.1-31.4 kJ mol-1. The isotherms were fitted with the Langmuir model, indicating a favourable monolayer adsorption with high affinity. The sorption energy, calculated by Dubinin-Radushkevich, 9.60-8.80 kJ mol-1, confirms a sorption mechanism mediated by ion exchange. The thermodynamic parameters of the process were ΔG°(-21.7/-19.7 kJ mol-1), ΔH°(16.7 kJ mol-1) and ΔS°(123.3 J mol-1 K-1).

In this paper we present magnetoelectric properties of metal/metal-oxide/metal junctions. We use Ti and Fe as metallic layers separated by the porous metal-oxides of iron or titanium formed with the anodization method. This allowed to prepare double junctions with at least one ferromagnetic layer. Here we show magnetoresistance and current-voltage characteristics of the junctions together with their magnetic characteristics. We found positive or negative magnetoresistance depending on junction composition. We discuss also the nature of differential resistance calculated from I-V characteristics. Our findings show that the strongest influence on observed behaviour has a top metallic layer and the interface between this layer and anodized oxide where strong interatomic diffusion is expected.

Balanced nitrogen (N) and phosphorus (P) rates coupling with rational fertilization methodology could promote crop N accumulation, N use efficiency and yield production, particularly in semi-arid and arid regions. To test these characteristics, a two-year (2018 and 2019) pot experiment was therefore performed by growing summer maize in a rain-proof glass greenhouse, under 9 combined N (112, 150 and 187 kg ha-1, urea) and P (45, 60, 75 kg ha-1, calcium superphosphate) rates and three contrasting fertilizer placements. The fertilizers were placed by broadcast on soil surface (Broadcast), side band on 4 cm strip soil surface within 7 cm from sowing line (Side band) and deep band on 4 cm strip below 7 cm soil depth within 7 cm from sowing line (Deep band). Results from three maize growth stages (eight-leaf, 45 days after sowing, DAS; tasseling, 60 DAS; and harvest, 115 DAS) showed that leaf, stem, root N accumulation and total soil N were significantly increased under Deep band than under both Side band and Broadcast at N150P60, N187P60, N150P75 and N187P75, but not at N112P45, N150P45, N187P45, N112P60 and N112P75. Significantly greater leaf, stem, and root N accumulations were also displayed at N150 and N187 than at N112 for the same P60 or P75 under Deep band at 60 DAS and 115 DAS, while were for leaf and stem N accumulations at P75 and P60 than at P45 for the same N150 under Deep band at 45 DAS, 60 DAS and 115 DAS. Significantly greater agronomy N use efficiency, partial factor productivity and N use efficiency exhibited under Deep band than under Side band and Broadcast at N150P75 and N187P75, but at N150P60 and N187P60 for NUE only. In addition, leaf, stem, seed, root N concentrations positively correlated with their own N accumulations or soil N concentration at tasseling and harvest stages. Our results demonstrate that a synchronized N150P60, N187P60, N150P75 or N187P75 fertilization rate with Deep band placement can improve soil N availability and root N uptake, and hereby greater aboveground N accumulation, N use efficiency and yield production of maize particularly practical for small-holder farmers globally.

Abstract: Cancer cells are originated by normal cells and with those share the need to be fed. Metabolic reprogramming in cancer cells is not yet fully understood although there is a vast literature suggesting that huge amounts of both energy and substrates are require for synthesis of components of new neoplastic cells so that any macronutrient may be efficiently utilized. Recently, in vitro data show that EAA supplementation promoted colon cancer cells apoptosis by enhanced autophagy. Therefore, in this study we tested in vivo the effects of matched macronutrients standard laboratory diet (control) versus EAA rich modified diet (EAArmd) in mice injected with colon cancer cells. Results of the first set of 12 animals, 6 controls and 6 EAArmd-fed, showed that controls mice develop cancer volume cancers 5 times larger and heavier than EAArmd-fed. If confirmed, these results would open new scenarios for the cancer integrate therapies.

Nitrogen is crucial for plant physiology due to the fact that plants consume a significant amount of nitrogen during the development period. Nitrogen supports the root, leaf, stem, branch, shoot and fruit development of plants. At the same time, it also increases flowering. To monitor the vegetation nitrogen concentration, one of the best indicator developed in the literature is Normalized Difference Nitrogen Index (NDNI) which is based on the usage of the spectral bands: 1510 and 1680 nm. from Short-Wave Infrared (SWIR) region of electromagnetic spectrum. However, majority of the remote sensing sensors like cameras and/or satellites do not have a SWIR sensor due to the high costs. Many vegetation indexes like NDVI, EVI, MNLI, have been developed in also VNIR region to monitor the greenness and healthy of the crops. However these indexes are not very correlated to the nitrogen content. Therefore, in this study, a novel method is developed which transforms the estimated VNIR band indexes to NDNI by using a regression method between a group of VNIR indexes and NDNI. Training is employed by using VNIR band indexes as input and NDNI as output which are both calculated from the same location. After training, 0.93 correlation is achieved. Therefore, by using only VNIR band sensors, it is possible to estimate the nitrogen content of the plant with high accuracy.

Emissions from wood burning for heating in secondary homes or cabins is an important aspect for the development of high-resolution emission inventories in specific areas. Norway is used as case study as the national wood consumption for heating in cabins is around 20% of the total. Our study shows first a method to estimate emissions from cabins based on traffic data to derive cabin occupancy, which combined with heating need allows for the spatial and temporal distribution of emissions. The combination of residential (RWC) and cabin wood combustion (CWC) emissions shows large spatial and temporal differences, and a temporally “cabin population” can in areas be orders of magnitude larger than the registered population. While RWC emissions have been steadily reduced, CWC have kept relatively constant or even increased, which results on an increase in the cabin share to total heating emissions up to 25-35%. When comparing with regional emissions inventories, our study shows that the gradient between rural and urban areas is not well represented in regional emissions inventories, which resembles a population-based distribution and does not allocate emissions in cabin municipalities. At last, our study shows that CWC emissions may become an increasing environmental concern as higher densification trends in mountain areas are observed.

Plant N concentration (PNC) has been commonly used to guide farmers in assessing maize (Zea mays L.) N status and making in-season N fertilization decisions. However, PNC varies based on the development stage and therefore a relationship between biomass and N concentration is needed (i.e., critical N dilution curves; CNDC) to better understand when plants are N deficient. A few CNDC have been developed and used for plant N status diagnoses, but have not been tested in the US Midwest. The objective of this study was to evaluate under highly diverse soil and weather conditions in the US Midwest the performance of CNDCs developed in France and China for assessing maize N status. Maize N rate response trials were conducted across eight US Midwest states over three years. This analysis utilized plant and soil measurements at V9 and VT development stages and final grain yield. Results showed that the French CNDC (y=34.0x-0.37, where y is critical PNC, x is aboveground biomass) was better with a 91% N status classification accuracy compared to only 62% with the Chinese CNDC (y=36.5x-0.48). The N nutrition index (NNI), which is the quotient of the measured PNC and the calculated critical N concentration (Nc), based on the French CNDC was significantly related to soil nitrate-N content (R2=0.38-0.56). Relative grain yield on average reached a plateau at NNI values of 1.36 at V9 and 1.21 at VT, but for individual sites ranged from 0.80 to 1.41 at V9 and from 0.62 to 1.75 at VT. The NNI threshold values or ranges optimal for crop biomass production may not be optimal for grain yield production. It is concluded that the CNDC developed in France is suitable as a general diagnostic tool for assessing maize N status in US Midwest. However, the threshold values of NNI for diagnosing maize N status and guiding N applications vary significantly across the region, making it challenging for guiding specific on-farm N management. More studies are needed to determine how to effectively use CNDC to make in-season N recommendations in the US Midwest.

This study introduces and demonstrates a comprehensive, accurate, unbiased approach to robust quantitative comparison of Electronic Nicotine Delivery Systems (ENDS) appropriate for establishing substantial equivalence (or lack thereof) between tobacco products. The approach is demonstrated across a family of thirteen pen- and pod-style ENDS products. Methods employed consist of formulating a robust emissions surface regression model, quantifying the empirical accuracy of the model as applied to each product, evaluating relationships between product design characteristics and maximum emissions characteristics, and presenting results in formats useful to researchers, regulators, and consumers. Results provide a response surface to characterize emissions (total particulate matter and constituents thereof) from each ENDS appropriate for use in a computer model and for conducting quantitative exposure comparisons between products. Results demonstrate that emissions vary as a function of puff duration, flow rate, E-Liquid composition, and device operating power. Further, results indicate that regulating design characteristics of ENDS devices and consumables may not achieve desired public health outcomes; it is more effective to regulate maximum permissible emissions directly. Three emissions outcome measures (yield per puff, mass concentration and constituent mass ratio) are recommended for adoption as standard quantities for reporting by manufacturers and research laboratories. The approach provides a means of (a) quantifying and comparing maximal emissions from ENDS products spanning their entire operating envelope, (b) comparative evaluation of ENDS devices and consumable design characteristics, and (c) establishing comparative equivalence of maximal emissions from ENDS. A consumer-oriented product emissions dashboard is proposed for comparative evaluation of ENDS exposure potential. Maximum achievable power dissipated in the coil of ENDS is identified as a potentially effective regulatory parameter.

Inherent low soil fertility status limits productivity of rice in the lowland ecologies in Northern Ghana. Combining organic and inorganic N fertilizers could help to maintain the fertility of lowland soils for rice production. A screen house pot experiment was carried out to investigate the combined effect of biochar-compost and inorganic N fertilizer on the nitrogen uptake and agronomic performance of rice plants grown on Eutric Gleysol lowland soil. Inorganic N fertilizer alone and its combinations with different types of biochar-compost (based on the proportions of biochar and compost) were used as treatment. A control (unamended soil) was also included. The incorporation of biochar-compost and inorganic N fertilizer improved the growth parameters and yield components of rice plants. The combination of biochar-compost and inorganic nitrogen fertilizer was also found to improve nitrogen uptake and nutrient use efficiency (NUE) in rice plants. This practice could be the most likely viable option for alleviating lowlands soil fertility issues and increasing rice productivity in Northern Ghana.

The relation between CO2 emissions and atmospheric CO2 concentration has traditionally been treated with more or less complex models with several boxes. Our approach is motivated by the question of how much CO2 must necessarily be absorbed by sinks. Observations lead to the model assumption, that carbon sinks like oceans or biosphere are linearly dependent on CO2 concentration on a decadal scale. In particular this implies the falsifiable hypothesis that oceanic and biological CO2 buffers have not significantly changed in the past 50 years and are not saturated in the forseeable future. The simple model with 2 parameters explains very well the CO2 emission and historical CO2 concentration data. The model gives estimates of the natural emissions, the pre-industrial CO2 equilibrium concentration levels, the half-life time of an emission pulse, and the future CO2 concentration level from a given emission scenario. This is validated by an ex-post forecast of the last 20 years. The important result is that with the stated polices scenario of the IEA future CO2 concentrations will not rise above 475 ppm. The model is compared with the Carbon modul of the Bern model, mapping their complex IRFs to a single time variant parameter.

Nanostructured anodic oxide layers on an FeAl₃ intermetallic alloy were prepared by two-step anodization in 20 wt.% H2SO4 at 0°C. The voltage range was 10.0 – 22.5 V with a step of 2.5 V. The structural and morphological characterizations of the received anodic oxide layers were performed by FE-SEM. Therefore, the formed anodic oxide was found to be highly porous with a high surface area, as indicated by the FE-SEM studies. It has been shown that the morphology of fabricated nanoporous oxide layers is strongly affected by the anodization potential. The oxide growth rate first increased slowly (from 0.010 μm/s for 10 V to 0.02 μm/s for 15 V) and then very rapidly (from 0.04 μm/s for 17.5 V up to 0.13 μm/s for 22.5 V). The same trend was observed for the change in the oxide thickness. Moreover, for all investigated anodizing voltages, the structural features of the anodic oxide layers, such as the pore diameter and interpore distance, increase with increasing anodizing potential. The obtained anodic oxide layer was identified as a crystalline FeAl₂O₄, Fe₂O₃ and Al₂O₃ oxide mixture.

Maize (Zea mays L.) is the most widely grown important crop in mid altitude areas of intensive maize-based cropping system of western Ethiopia. Agronomic management is the most important input for getting potential yield and high net returns in hybrid maize production. A field experiment was carried out on farmers’ field to find out the effect of varieties (four maize) and nitrogen fertilizer rate (55, 110 kg N ha-1) with one control on yield components and nitrogen use efficiency of different maize varieties in 2013 and 2014 cropping season. It was laid with randomized complete block design in factorial arrangement with three replications. Mean grain yield, thousand seed weight, dry biomass and harvest index of maize varieties were significantly differed among farms and varieties of maize. Application of nitrogen fertilizer rates was significantly increased mean grain yield maize varieties. Interaction of maize varieties with nitrogen fertilizer rates was significantly affected all yield components of maize varieties. Application half and full recommended nitrogen fertilizer gave mean grain yield advantages of 31 and 41 % over control maize varieties planted without nitrogen application. Maize varieties producing higher mean grain yield was also giving higher mean dry biomass. Mean nitrogen up take was varied from 225 to 357 kg ha-1 among varieties of maize. Higher agronomic efficiency of all maize varieties was obtained from maize planted with application half recommended nitrogen fertilizer compared to full recommend. Agronomic efficiency was ranged from 18 to 33 produced among maize varieties. Significantly higher nitrogen up take efficiency of maize varieties was achieved from maize planted with full recommended nitrogen fertilizer application. Considerably higher nitrogen use efficiency of maize varieties was realized from all maize varieties planted with application half recommended nitrogen fertilizer. Application of half recommended nitrogen fertilizer was gave 32 % fertilizer N use efficiency advantage as compared to full recommended nitrogen fertilizer. Maize varieties BH-661>BH-660> BH-543>BH-540>BH-140 were desirable varieties for further promotion work and use by smallholder farmers in mid altitude area of western Ethiopia.

Coal mining has caused a significant loss of nitrogen content of soil in mining areas. This article studies the effects of organic fertilizer, inorganic fertilizer, and combined application of Pseudomonas fluorescens with the ability of nitrogen fixation on soil nitrogen accumulation and composition in the reclamation area of Tunlan Coal Mine from 2016 to 2022 under the condition of equal nitrogen application, providing scientific basis for microbial fertilization and rapid increase of nitrogen content in the reclaimed soil of mining areas. The results showed that as the reclamation time increased, the nitrogen content and its composition structure of the soil treated with fertilization rapidly evolved towards normal farmland soil. The soil nitrogen content increased the fastest in the treatment of Pseudomonas fluorescens + organic fertilizer (MB), compared with inorganic fertilizer (CF), organic fertilizer (M), and Pseudomonas fluorescens + inorganic fertilizer (CFB) treatments, the treatment of Pseudomonas fluorescens + organic fertilizer (MB) can bring the total nitrogen (TN) content of the soil to normal farmland soil levels 1-3 years earlier. The comprehensive scores of Pseudomonas fluorescens + organic fertilizer (MB) and Pseudomonas fluorescens + inorganic fertilizer (CFB) on the two principal components were increased 1.58 and 0.79 than those of organic fertilizer (M) and inorganic fertilizer (CF) treatments, respectively. This further indicates that the combination of Pseudomonas fluorescens and organic fertilizer has a better effect on improving soil nitrogen accumulation than the combination of Pseudomonas fluorescens and inorganic fertilizer. At the same time, the application of Pseudomonas fluorescens will increase the content of unknown nitrogen (UN) in acid-hydrolysable nitrogen (AHN), and decrease the content of amino acid nitrogen (AAN) and ammonia nitrogen (AN), relatively. However, there was no significant effect on the content of ammonium nitrogen (NH4+-N) and nitrate nitrogen (NO3--N) in soil inorganic nitrogen (SMN). When combined with inorganic fertilizer, the contribution of soil mineralized nitrogen (SMN) to total nitrogen (TN) increased by 14.78%, while when combined with organic fertilizer, the contribution of acid-hydrolysable nitrogen (AHN) to total nitrogen (TN) increased by 44.77%. In summary, the use of Pseudomonas fluorescens is beneficial for nitrogen recovery in the reclaimed soil of coal mining areas. The optimal fertilization method under the experimental conditions is the combination of Pseudomonas fluorescens and organic fertilizer.

Lithium rich layered oxides (LRLO) are a wide class of innovative active materials for positive electrodes in lithium-ion (LIB) and lithium-metal secondary batteries (LMB). LRLOs are over-stoichiometric layered oxides rich in lithium and manganese, with general formula Li1+xTM1-xO2, where TM is a blend of transition metals comprising Mn (main constituent), Ni, Co, Fe and others. Due to the very variable composition and the extended defectivity their structural identity is still debated among researchers being likely an unresolved hybrid between a monoclinic (mC24) and a hexagonal lattice (hR12). Once casted in composite positive electrode films and assembled in LIBs or LMBs, LRLOs can delivery reversible specific capacities above 220-240 mAhg-1, thus beyond any other available intercalation cathode material for LIBs, with mean working potential above 3.3-3.4 V vs Li for hundreds of cycles in liquid aprotic commercial electrodes. In this review we critically outline the recent advancements in the fundamental understanding of the physico-chemical properties of LRLO as well as the most exciting innovations in their battery performance. We focus in particular on the elusive structural identity of these phases, on the complexity of the reaction mechanism in batteries as well as on practical strategies to minimize or remove cobalt from the lattice while preserving the outstanding performance upon cycling.

The article presents a technology for producing nitrogen-containing nanoporous biocarbon with high degree of elemental composition homogeneity, confirmed by electron spectroscopy. The research explores the relationship among the electronic characteristics of supramolecular nanoporous carbon, its porous structure, and the capacitance at its interface with the electrolyte. The obtained biocarbon is characterized by micro and mesopores, as evidenced by the results of studies by the method of nitrogen adsorption/desorption. The specific area of the available porous surface was found to be 1247 m2/g. Comparing this result with the data of small-angle X-ray scattering, we conclude that micropores are open while mesopores remain closed. This material was found to have a saturation magnetization σs of 1.4 A∙m2∙kg-1 and a coercive force Hc of 10 kA/m. The impedance studies of electrochemical cells of supercapacitors made of the experimental biocarbon were carried out. Equivalent electrical circuits of the studied electrochemical processes were constructed and characterized.

Distributed Energy Resources might have a severe influence on Power Line Communications, as they can generate interfering signals and high frequency emissions or supraharmonics that may cause loss of metering and control data. In this paper, the influence of various energy resources on Narrowband Power Line Communications is described and analyzed through several test measurements performed in a real microgrid. Accordingly, the paper describes the effects on smart metering communications through MAC layer analysis. Results show that the commutation frequency of inverters and the presence of battery chargers are remarkable sources of disturbance in low voltage distribution networks. In this sense, the results presented can contribute to efforts towards standardization and normative of emissions at higher frequencies higher, such as CENELEC EN 50160 and IEC/TS 62749.

Tungsten oxides play a pivotal role in a variety of modern technologies e.g., switchable glasses, wastewater treatment, and modern gas sensors. Metallic tungsten is used as armor material, for e.g., gas turbines as well as future fusion power devices. In the first case, oxides are desired as functional materials, while in the second case, oxides can lead to catastrophic failures, so avoiding the oxidation of tungsten is desired. In both cases, it is crucial to understand the reactivity of tungsten oxides with other chemicals. In this study, the different reactivities of tungsten oxides with the highly-oxophilic beryllium are studied and compared. Tungsten-(IV)-oxide and tungsten-(VI)-oxide layers are prepared on a tungsten substrate. In the next step, a thin film of beryllium is evaporated on the samples. In consecutive steps, the sample is heated in steps of 100 K from r. t. to 1273 K. The chemical composition is investigated after each experimental step by high-resolution X-ray photoelectron spectroscopy (XPS) of all involved core levels as well as the valence band. A model is developed to analyze the chemical reactions after each step. In this study, we find that tungsten trioxide was already reduced by beryllium at r. t. and started to react to form the ternary compounds BeWO₃ and BeWO₄ at temperatures starting from 673 K. However, tungsten dioxide is resistant to reduction at temperatures of up to 1173 K. In conclusion, we find WO₂ to be much more chemically resistant to the reduction agent Be than WO₃.

The up-to-date challenge towards clean road transport are non-exhaust emissions. Important advances regarding measurement systems, including well defined characterisation techniques, as well as regulation, will happen in the next few years. In this work we present detailed results of particle emissions from a test bed for wheel suspension and brakes, consisting of aerosol (size distribution, particle number (PN) and mass (PM)) and electron microscopy measurements (EM) under different load conditions. Standard tyres and brakes from series production were tested with a high-load driving cycle while particle measurements were conducted by gravimetric measurements and with a TSI SMPS, a TSI APS and a GRIMM OPS. Furthermore, samples were analyzed by electron microscopy. A bimodal particle size distribution (PSD) was obtained with the SMPS, with peaks at 20nm and around 400nm. EM analysis of &gt;1400 single particles from the electrostatic sampler matches the PSD results. EM analysis also showed ultrafine particles, mainly from O, Fe, Si, Ba, Mg and S and also fractal particles with high C fractions. Our results suggest, in agreement with previously published literature, that particulate emissions are related to brake disc temperature and occur in significant amounts above a threshold temperature.

The mosquito microbiota reduces the vector competence of Anopheles to Plasmodium and affects host fitness, it is therefore considered as a potential target to reduce malaria transmission. While immune induction, secretion of antimicrobials and metabolic competition are three typical mechanisms of microbiota-mediated protection against invasive pathogens in mammals, the involvement of metabolic competition or mutualism in mosquito-microbiota and microbiota-Plasmodium interactions has not been investigated. Here, we describe a metabolome analysis of the midgut of An. coluzzii provided with a sugar-meal or a blood-meal, under conventional or antibiotic-treated conditions. We observed that the antibiotic treatment affects the tricarboxylic acid cycle and nitrogen metabolism, notably resulting in decreased abundance of free amino acids. Linking our results with published data, we identified candidate pathways which may participate in microbiota/Plasmodium interactions via metabolic interactions or immune modulation.

Biopolymers are of growing interest, but to improve some of their poor properties and performance, it is required the formulation of bio-based blends and/or adding of nanoparticles. For this purpose, in this work, two different metal oxides, such as zinc oxide (ZnO) and titanium dioxide (TiO2), at different concentrations (0.5, 1 and 2 %wt.) have been added in polylactic acid (PLA) and polylactic acid/polyamide 11 (PLA/PA11) blends to establish their effects on solid-state properties, morphology, melt behaviour, and photo-oxidation resistance. It seems that the addition of ZnO in PLA leads to a significant reduction of its rigidity probably due to an inefficient dispersion in the melt state, while the addition of TiO2 does not penalise PLA rigidity. Interestingly, the addition of both ZnO and TiO2 in PLA/PA11 blend has a positive effect on the rigidity because of blend morphology refinement and leads to a slight increase in film hydrophobicity. The photo-oxidation resistance of neat PLA and PLA/PA11 blend is significantly reduced due to the presence of both metal oxides, and this must be considered when designing the potential applications. The last results suggest that both metal oxides could be considered as photo-sensitive degradant agents for biopolymer and biopolymer blends.

Alternative fuels available at low cost, friendly to natural environments and meet the energy needs and demands, have witnessed a growing demand and use today. Ethanol is an attractive renewable energy source with a high content of oxygen. Ethanol can be produced through ethanolisis, however for this work direct blending of conventional diesel, waste plastic pyrolysis oil and ethanol with commercial fuel improver CI-0808 purchased from Innospec company was attempted. The primary purpose of adding a cetane improver was to improve the combustion characteristics of the blends by at least 1- 3 ignition quality points. Five mixing ratios were chosen in the following order, 50:25:25, 60: 20:20, 70: 15:15, 80: 10:10 and 90: 5:5 for Waste Plastic Pyrolysis Oil (WPPO), ethanol and conventional diesel (CD) respectively. However, for the fuel additive mixing ratio the total volume percentage was considered and the ratio put at 0.01% of the total quantity of blended fuel. In this work WPPO, diesel blends and fuel additives improvers were used as alternative fuel. This was to evaluate their performance and emission characteristics in a stationary single cylinder water cooled experimental diesel engine. The CI-0808 was added due to its potential power to reduce emissions of CO, UHC, NO_X, PM and improved engine performance. The results obtained were compared carefully to ASTM standards and discussed using graph curves figures and tabulated values. The conclusion was that ethanol and WPPO blends can be used in diesel engines as alternative fuel without modification. Used in combination with cetane improvers the emissions reduce significantly and performance improved equalling that of conventional diesel fuel.

This paper addresses the atmospheric emissions from oil and gas extraction and production in Greece. The study was carried out in 2014 in the Kavala gulf, which currently is the only location of oil and gas production in Greece and where the exploration activities for hydrocarbons started in the late ‘60’s. This study presents the qualitative and quantitative characteristics of atmospheric emissions, in relation also to the emissions’ control management system. Particular reference is made to sulphur compounds since the existence of volcanic rocks results to increased amounts of H₂S. The results shows that, currently, atmospheric emissions of pollutants during extraction and production of hydrocarbons in Greece are very low and do not have any significant effect on air quality and climate change. Since it is expected that exploitation of hydrocarbons and oil and gas extraction and production will increase in the future, appropriate measures should be taken to ensure environmental protection, such as the development of integrated monitoring systems and the use of up to date emission control technologies.

The use of alternative fuels and electric vehicles is an opportunity to reducing exhaust emissions. We observe that the regulations on exhaust emissions from mobile sources are becoming gradually stricter on the all the world. As is widely known, using alternative fuels instead of conventional fuels helps lower vehicle emissions. The most popular alternative fuels are hydrogen, propane, biobutanol, methanol, dimethyl ether, etc. It is very important that more than a dozen alternative fuels are under development. The article contains a comparison of the operating costs of electric cars and cars with an internal combustion engine. This work shows also the characteristic of new alternative fuels and their impacts on exhaust emissions.

The link between ICTs, freight transport, and CO₂ emissions has not received much explicit examination by researchers, despite freight transportation being an egregious contributor to environmental degradation. This paper investigates how ICTs can affect environmental quality when interacting with freight transport activities in 43 countries over the period 2002-2014, using carbon emissions as a proxy for environmental damages. ICTs are measured in terms of internet, telephone, and mobile phone technologies. Using GMM methodology, the results show that ICTs contribute to dampening environmental degradation when interacting with freight transport activities. Specifically, a 10% increase in the interaction between ICTs and freight transportation will decrease carbon emissions by between 1.27% and 3.02%. The results further suggest that fixed and smartphone technologies are the main contributors to reducing emissions when adopted in some specific transport sectors (i.e. road, rail, and inland), while the internet is the most efficient technology when interacting with air transport activity. In addition, the interaction between ICTs and multimodality accelerates environmental quality. The policy implications of these findings are discussed.

Researchers’ attention has been turned on Health expenditure, Carbon emissions, and economic growth as they play a focal role in the current debate on environmental protection and sustainable development. Our paper endeavors to investigate the impact of economic growth and CO2 emissions on Health expenditure for two main countries in Asia (China and India) using a dynamic panel data model estimated employing the Generalized Method of Moments (GMM) for the period 1960–2019. Our empirical results show that there is a significant relationship between health expenditure, CO2 emissions, and economic growth. The empirical evidence indicates a significant positive impact of CO2 emissions on health expenditure whiles economic growth has a negative impact on health expenditure for both countries for the period under study. The population growth rate has transposed effect on India's health spending; on the other hand, its impact on China’s health spending is significantly positive. The strong observable correlation between health expenditure and economic growth is crucial for economic development.

The population’s mobility in urban areas is a necessary variable in the modeling of risk scenarios caused by atmospheric contamination. The inclusion of this concept makes static models more dynamic while considering people within a city to be an entity with complex mobility processes. We propose a conceptual and methodological tool to make the representation of the social, economic and territorial components, as well as the patterns in the population´s mobility to delimitate risk areas for human health by exposure of contaminants. In the volatile organic compounds (VOC), benzene, ethylbenzene, toluene and xylene (BTEX) are amongst the most dominant substances in fugitive vapor emissions in gas stations (GS). In urban areas, the exposure to BTEX by residential proximity and proximity to other facilities, which cause intra-urban agglomeration, can impact and affect human health. This model seeks to facilitate the focalization, identification and prioritization of risk areas by BTEX environmental contamination. This article goes beyond de conceptual framework. It suggests methodological and instrumental aspects to be applied in other cities. The government agencies must consider these results when establishing rules, permissions and procedures to reduce environmental pollution for managing the risk in a complex urban environment.

Taking into account the increase in the emission of greenhouse gases produced by ships, during navigation and maneuvering in the port, a direct consequence of the increase in maritime traffic, the international community has developed a broad set of regulations to limit such emissions. The installation in commercial ports of automatic mooring systems by means of vacuum suction cups (AMS), thus reducing considerably the time required to carry out the mooring and unmooring maneuvers of ships, is a factor that is considerably influencing the decrease in Emissions of polluting gases in commercial ports with high traffic. The objective of the present work is to verify the influence of the use of the AMS on the emissions of polluting gases produced in the facilities destined to the traffic of container ships. It examines the CO2 emissions of container ships that call in the only three container ports equipped with AMS: Salalah (Oman), Beirut (Lebanon) and Ngqura (South Africa). Between them, these three ports supported the transit of 6 million TEUS in 2017. The calculation of emissions is made taking into account the time saved when performing the mooring maneuvers using the new AMS system compared with when it is not used. To do this, two different calculation methods are used: EPA and ENTEC to then compare the results of the two and thus obtain the reduction in emissions per TEU in these terminals during the mooring maneuvers. The paper concludes with a discussion on the values of the reductions in emissions obtained and the advantages of the installation of AMS in commercial ports located near population centres.

This work communicates laser-plasma experiments in a gaseous mixture of hydrogen and nitrogen. Time-resolved spectroscopy measures the first four Balmer series hydrogen lines together with selected neutral and ionized nitrogen lines. Optical breakdown plasma is generated in a 1:1 hydrogen:nitrogen mixture at ambient temperature and 0.27-atm pressure. Time-resolved spectroscopy records emitted radiation with spatial resolution along the slit height for the H_α, H_β, H_γ, and H_δ lines. For 13 selected time delays from 0.25 µs to 3.25 µs and 0.025 µ gate-widths, micro-plasma diagnostics is evaluated. Of interest are the peak-separation and width of H_δ and width of H_γ for electron densities in the range of 0.1 to 1.0×10¹⁷ cm^-3, and comparisons with H_β and H_α diagnostics. Integral inversions interrogate spatial distributions of the plasma expansion. Applications include laboratory and stellar astrophysics plasma diagnosis.

Irrigation and fertilization are indispensable links in the jujube planting industry in southern Xinjiang, China. However, the water and fertilizer integration effects on jujube growth and fruit quality remain unclear. A two-year water and fertilizer optimization coupling test was conducted to determine the optimal water- and nutrient-supply scheme. The three-factor randomized block experiment included water (W), nitrogen (N), and phosphorus (P). According to the principal component analysis of each index, each treatment’s comprehensive score was obtained. Using yield and economic regression models, the theoretical value and yield value of the optimal economic benefit are inferred. When W, N, and P were applied together, the fruit quality and yield of each treatment significantly differed, and the vitamin C, soluble sugar, and sugar–acid ratio increased significantly with an increase in nitrogen fertilizer. However, the titratable acid decreased. An increase in irrigation and nitrogen application significantly increased fruit yield. The comprehensive score was the highest in the N3P3W2 treatment, which improved fruit quality, and the lowest in the N4P3W2 treatment. When the amounts of N, P, and W were 275.56 kg·hm-2, 413.66 kg·hm-2, and 7278.19 m3·hm-2, respectively, the theoretical economic benefit was the best. The N4P3W2 treatment is the optimal treatment.

Conservation tillage and deep side-fertilization both hold the potential to reduce nitrogen leaching and improve grain yield and nitrogen use efficiency in fragrant rice cultivation practices. However, the combined impact of different tillage practices with deep side-fertilization on nitrogen leaching remains uncertain. Therefore, this study conducted on-site experiments for four rice growing seasons in both early and late seasons in 2018 and 2019, using the fragrant rice varieties "Meixiangzhan 2"(MX) and "Xiangyaxiangzhan"(XY). The four experimental treatments included:conventional tillage with regular fertilization (T1), conventional tillage with simultaneous deep fertilization (T2), reduced tillage with simultaneous deep fertilization (T3) , and no-tillage with simultaneous deep fertilization (T4). Our results indicate that the T4 treatment exhibited higher nitrogen leaching rates and potential nitrogen losses throughout the entire rice growth cycle, with a 4.51% increase in total nitrogen leaching and a 1.86% increase in potential nitrogen leaching compared to T1. In contrast, the T2 treatment demonstrated the lowest nitrogen leaching rate, resulting in a 6.01% reduction in total nitrogen leaching and a 9.57% decrease in potential nitrogen leaching compared to T1, demonstrating the most optimal performance. For MX, the T1 treatment resulted in lower daily grain outputs compared to the other treatments, with disparities ranging from 5.35% to 9.94%. Similarly, for the XY, the T1 treatment yielded significantly lower daily grain outputs compared to the other treatments, with discrepancies ranging from 6.26% to 10.81% during the late season of 2019. Overall, this study shows that conventional tillage with deep fertilization effectively reduces nitrogen leaching and boosts fragrant rice yields. Minimizing nitrogen leaching enhances nitrogen utilization efficiency. These insights highlight the significance of strategic fertilization and cultivation for environmental conservation and agricultural sustainability.

Empirical models help us understand the process of plant residue decomposition and nutrient release into the soil. The objective of this study was to determine an appropriate model to describe the decomposition of hairy vetch (Vicia villosa Roth) and cereal rye (Secale cereale L.) cover crop (CC) residue and nitrogen (N) release. Data pertaining to above and belowground CC residue mass loss and N release for up to 2633 cumulative decomposition degree days (112 d) after litterbag installation were obtained from two cropping system experiments, one conducted in 2015 and the other in 2017 and 2018 at the humid subtropical environment of southern IL, USA. Six exponential and two hyperbolic models were fit to percent mass and N remaining data to find the one with minimum Akaike Information Criterion (AIC) and residual sum of squares. Modified three-parameter single exponential and two- or three-parameter hyperbolic models best met the assumed criteria of selection for above and belowground CC residue, respectively. Fitting a double exponential model to a combined data for percent mass and N remaining, which identified two mass and N pools, a fast and a slow pool with different rate constants. A five-parameter double exponential with an asymptote met the preset criteria and passed all tests for normally distributed population, constant variance, and independence of residuals at α = 0.05 when fit to combined data of hairy vetch shoot mass and N remaining. However, a two-parameter hyperbolic and three-parameter asymptotic hyperbolic model provided the best fit to a combined data of cereal rye shoot mass and N remaining, respectively. Both hyperbolic decay models showed a good fit for belowground mass decomposition and N release for both CCs. Cereal rye had poorer fit than hairy vetch for mass and N remaining of both above and belowground mass. The best-selected decay models can be used to estimate the decomposition and N release rates of hairy vetch and cereal rye above and belowground residue in a similar environment.

With a worldwide growing concern for greenhouse gas (GHG) emissions and their impact on human health and the environment, transportation has become a central theme in mitigation, responsible for 14% of human GHG emissions. To build endurance to climate change, transportation services must adapt to the current scenario and act quickly to avert future changes. Deeply rooted changes in socio-technical systems will be necessary to achieve significant CO2 reduction and secure the well-being of future generations. This study's objective is to comprehensively review the current state of carbon mitigation in the transportation sector. This is done through a systematic literature review engrained in the socio-technical transition theory and the structural theory of contingency. Twenty-six review papers covering 2,983 original articles are selected for full-text examination concerning carbon emissions in transportation. Enablers, barriers, benefits, disadvantages and metrics in carbon emissions reduction are identified, and a comprehensive framework is built. Results provide a view of the current sustainability scenario in transportation and allow a better understanding of the factors influencing carbon emission initiatives in transportation and its outcomes.

Due to the shortage of agricultural labor forces and rapid aging of farmers, the utilization of tractors is becoming popular and essential in Korea. Tractors can be classified into two types, a walking tractor called as a power tiller and a riding tractor. In this study, agricultural tractors including walking and riding types were categorized into 4 levels by rated output power. And diesel emission inventory of tractors was established and analyzed using 2011 and 2019 survey data in Korea. Emission inventory including CO, NOx, SOx, TSP(PM10), PM2.5, VOCs and NH3 were established using Tier 3 methodology. The total amount of emission using agricultural tractors was decreased about 13% from 2011 to 2019. The number of walking tractors were decreased by about 19% in 8 years, on the other hand that of riding tractors were increased by about 12%. However, the emission reduction is about 48% for walking tractors and the emission increment is about 5% for riding tractors. Thus, the total emission from agricultural tractors was decreased by about 16% in those periods. It is due to the decrease of 21% and 15% in the hours of use of walking and riding tractors, respectively, in 2019. Walking tractors mainly emit air pollutants from spraying and transporting. Riding tractors mainly 61% of total air pollutants emits from soil preparation and transporting operations. Geographic information system (GIS) was used to spatially assign air pollutants variables into 17 provinces and metropolitan cities in Korea. High emission generating regions and changes of emissions during 8 years were clearly seen in GIS analysis. High air pollutant emitting regions are mainly located in the western and southern regions of Korea, which have plenty of arable areas compared to other regions in Korea.

This review deals with the functionalization of double bonds carried out in the presence of a chiral catalyst exploiting the intramolecular attack to haliranium ions by nucleophilic nitrogen of amides or carbamates prepared from achiral aminoalkenes, and the C-N bonds formation leads to highly enantioenriched non-aromatic heterocycles. A range of protocols are reported, emphasizing the synthesis of many natural and biologically active products of pharmacological interest prepared according to this methodology.

Nitrogen is one of the most important macronutrients for crops, and in conjunction with artificial intelligence algorithms, it is possible to estimate it with the aid of vegetation indices through remote sensing. Various indices were calculated and those with a correlation ≥ 0.7 were selected for subsequent use in Random Forest, Gradient Boosting, and Artificial Neural Networks to determine their relationship with nitrogen levels measured in the laboratory. Random Forest showed no relationship, yielding an R2 of zero, whereas Artificial Neural Networks yielded the best results with an R2 of 0.93. Thus, it is reliable to estimate nitrogen levels using this algorithm by feeding it with data from TCARI, MCARI, TCARI/OSAVI, and MCARI/OSAVI, assisted by technological tools.

membrane separation technology shows promise, particularly gas separation membranes, including ceramic membrane. Ceramic membranes are increasingly gaining attention for their acid and alkali stability, corrosion resistance, high-temperature tolerance, and mechanical strength. This study focuses on alumina support ceramic membrane for CO2 capture. The membranes were characterized using contact angle measurements, scanning electron microscopy (SEM), and Fourier Transform Infrared spectroscopy (FTIR) analysis. The contact angle measurements confirmed the hydrophilic, while SEM analysis showed even particle distribution in the alumina ceramic membranes respectively. EDAX analysis revealed the elemental composition in the alumina support matrix. FTIR analysis demonstrated chemical interactions of the support membrane. Single gas permeation experiments were conducted. It can be observed that Nitrogen gas permeated faster with increase in feed pressure through the unmodified ceramic inorganic hydrophobic membrane more than the other two single gases, O2, and CO2). As a result, only high permeance separation membranes with realistic size and pressure conditions may be considered of as a practical alternative for CO2 capture. However, the presence of non-selective defects limited the improvement in selectivity of hydrophilic ceramic membrane. In this case, there is need to modify the ceramic membrane used to increase the flux, permeance of CO2, and selectivity of CO2.

Abstract: membrane separation technology shows promise, particularly gas separation membranes, including ceramic membrane. Ceramic membranes are increasingly gaining attention for their acid and alkali stability, corrosion resistance, high-temperature tolerance, and mechanical strength. This study focuses on alumina support ceramic membrane for CO2 capture. The membranes were characterized using contact angle measurements, scanning electron microscopy (SEM), and Fourier Transform Infrared spectroscopy (FTIR) analysis. The contact angle measurements confirmed the hydrophilic, while SEM analysis showed even particle distribution in the alumina ceramic membranes respectively. EDAX analysis revealed the elemental composition in the alumina support matrix. FTIR analysis demonstrated chemical interactions of the support membrane. Single gas permeation experiments were conducted. It can be observed that Nitrogen gas permeated faster with increase in feed pressure through the unmodified ceramic inorganic membrane more than the other two single gases, O2, and CO2). As a result, only high permeance separation membranes with realistic size and pressure conditions may be considered of as a practical alternative for CO2 capture. However, the presence of non-selective defects limited the improvement in selectivity of hydrophilic ceramic membrane. In this case, there is need to modify the ceramic membrane used to increase the flux, permeance of CO2, and selectivity of CO2.

Microalgae are used in various biotechnological processes, such as biofuel production due to their high biomass yields, agriculture as biofertilizers, production of high-value-added products, de-contamination of wastewater, or as biological models for carbon sequestration. The number of these biotechnological applications is increasing, and as such, any advances that contribute to reducing costs and increasing economic profitability can have a significant impact. Nitrogen fixing organisms, often called diazotroph, also have great biotechnological potential, mainly in agri-culture as an alternative to chemical fertilizers. Microbial consortia typically perform more com-plex tasks than monocultures and can execute functions that are challenging or even impossible for individual strains or species. Interestingly, microalgae and diazotrophic organisms are capable to embrace different types of symbiotic associations. Certain corals and lichens exhibit this sym-biotic relationship in nature, which enhances their fitness. However, this relationship can also be artificially created in laboratory conditions with the objective of enhancing some of the biotech-nological processes that each organism carries out independently. As a result, the utilization of microalgae and diazotrophic organisms in consortia is garnering significant interest as a potential alternative for reducing production costs and increasing yields of microalgae biomass, as well as for producing derived products and serving biotechnological purposes. This review makes an effort to examine the associations of microalgae and diazotrophic organisms, with the aim of highlighting the potential of these associations in improving various biotechnological processes.

An increasing body of evidence shows that seaweeds, including kelp, can be used as a tool to neutralize or remove excess nutrients and metals from the water column. Here we report on a preliminary field assessment showing potential nutrient and carbon removal differences by sugar kelp and ribbon kelp grown in common gardens. Seawater and tissue samples were collected systematically from two farms in Alaska. Results show differences between % N and % C content between ribbon kelp (Alaria marginata) and sugar kelp (Saccharina latissima). Results also show that tissue nitrogen in ribbon kelp varies sharply due to nitrogen availability in the water column. In contrast, the percentage of tissue N in sugar kelp remains comparatively stable. Our outcomes provide insight into potential differences in nutrient removal and harvest timing for different kelp species.

Alternative fuels containing biocomponents produced in various technologies are introduced in aviation to reduce its carbon footprint but there is little data describing their impact on the performance and emissions of engines. The purpose of the work is to compare the performance and gas emissions produced from two different jet engines: the GTM-140 microturbine and the full-size DGEN380 turbofan, powered by blends of Jet A-1 and one of two biocomponents: 1) ATJ and 2) HEFA produced from used cooking oil (UCO) in various concentrations. The acquired data will be used to develop an engine emissivity model to predict gas emissions. Blends of the mineral fuel with synthetic components were prepared in various concentrations, and their physicochemical parameters were examined in the laboratory. Measurements of emissions from both engines were carried out in selected operating points using the Semtech DS gaseous analyzer and the EEPS spectrometer. The impact of tested blends on engine operating parameters is limited, and their use does not carry the risk of a significant decrease in aircraft performance or increase in fuel consumption. Increasing the content of biocomponents causes a noticeable rise in the emission of CO and slight increase for some other gasses (HC and NOx), which should not, however, worsen the working conditions of the ground personnel. This implies that there are no contraindications against using tested blends for fuelling gas-turbine engines.

Although composting has many advantages in the treatment of organic waste, there are still many problems and challenges associated with emissions, like NH3, VOCs, and H2S, as well as greenhouse gases such as CO2, CH4, and N2O. One promising approach to enhancing composting conditions is used of novel analytical methods bad on artificial intelligence. To predict and optimize the emissions (CO, CO2, H2S, NH3) during composting process kinetics thought mathematical models (MM) and machine learning (ML) models were utilized. Data about everyday emissions from laboratory composting with compost’s biochar with different incubation (50, 60, 70 °C) and biochar doses (0, 3, 6, 9, 12, 15% d.m.) were used for MM and ML models selections and training. MM has not been very effective in predicting emissions, (R2 0.1 - 0.9), while ML models such as acritical neural network (ANN, Bayesian Regularized Neural Network; R2 accuracy CO:0,71, CO2:0,81, NH3:0,95, H2S:0,72)) and decision tree (DT, RPART; R2 accuracy CO:0,693, CO2:0,80, NH3:0,93, H2S:0,65) have demonstrated satisfactory results. For the first time the ML models to predict CO and H2S during composting were demonstrated. Further research in a semi-scale and field study composting with biochar is needed to improve the accuracy of developments models.

Agricultural intensification is considered essential for meeting growing demand for food and biomass for energy and material purposes. Intensifying grasslands is a so-far under-represented although promising option, given their large land area and relatively low management levels. This study quantifies the bioenergy potential from intensifying temporary grasslands in Europe and the integral greenhouse gas emission effects in 2030. We first conduct a literature review of intensification options for European grasslands and then apply the environmental impact assessment model MITERRA-Europe to implement the key intensification option of using multi-species grass mixtures. The results show that 853 kha (or 8%) of temporary grassland could be made sustainably available for additional biomass production. This can be translated into a bioethanol potential of 23 PJ/yr and an emission mitigation potential of 5.8 Mt CO2-eq/yr (if conventional grass mixture from surplus temporary grassland is used for energy) or 72 PJ/yr and 4.0 Mt CO2-eq/yr (if surplus temporary grassland is used for grassy energy crops). Although the bioenergy potential is limited, the intensification measure’s key advantage is that it results in a better environmental performance of temporary grasslands. This makes it a key option for sustainably producing bioenergy in areas with high shares of temporary grasslands.

In this paper a dynamic relationship between the CO2 emissions in Finland, Norway and Sweden is presented. With the help of a VAR(2) model, and using the Granger terminology, it is shown that the emissions in Finland are affecting those in Norway and Sweden. Other aspects of this dynamic relationship are presented as well.

Ceria, zirconia and mixed cerium-zirconium mesoporous oxides were synthesized and used as supports for sulfur and gold species. The materials were characterised using selected advanced techniques (ICP-OES, elemental analysis, XPS, XRD, N₂ adsorption and desorption isotherms, UV-vis, ATR-FTIR, TPR-H₂, TG-DTA) which allowed monitoring of the oxidation state of metals (cerium and gold) and the surface properties of the catalysts, in particular the concentration of the components on the surface and in the bulk of materials. The interactions between gold, sulfur and metals from oxides were considered. The goal of this work was studied the changes in the chemical composition of materials and the oxidation states of cerium species after the modification of oxides with sulfur and gold species and the estimation of the influence of these changes on the surface properties. The chemical composition of surface affects the mobility of surface oxygen and the oxidation state of cerium, which can play the role of redox sites (e.g. Ce³⁺/Ce⁴⁺ species), and therefore it strongly influences on the adsorption of hydrogen sulfide and then gold loading. Additionally, gold catalysts modified with sulfur species were tested in the reaction of glycerol oxidation in the liquid phase at basic conditions as the test reaction of the catalytic oxidation of organic pollutants from water.

In this article, copper(II) oxide, titanium dioxide and yttrium(III) oxide nanoparticles were added to Group III type base oil formulated with overbased calcium sulfonate. The nano-sized oxides were treated with ethyl oleate surface modification. The tribological properties of the homogenized oil samples were tested on a linear oscillating tribometer. Friction was continuously monitored during the tribological tests. Surface analysis was performed on the worn samples: the amount of wear was determined using a digital optical and confocal microscope. The type of wear was examined with a scanning electron microscope, while the additives adhered to the surface were examined with energy-dispersive X-ray spectroscopy. From the results of the measurements, it can be concluded that the surface-modified nanoparticles worked well with the overbased calcium sulfonate and significantly reduced both wear and friction. In the present tribology system, the optimal concentration of all three oxide ceramic nanoadditives is 0.4 wt%. By using oxide nanoparticles, friction can be reduced by up to 15% and the wear volume by up to 77%. Overbased calcium sulfonate and oxide ceramic nanoparticles together form a lower friction anti-wear boundary layer on the worn surfaces. It is advisable to further investigate the possibility of formulating nanoparticles into the oil.

Nitrogen (N) is the most limiting nutrient for the production of vegetable crops, but anthropogenic sources pose risks due to its transformation into several reactive forms and movement throughout the environment. To mitigate the impact of environmental losses, current research efforts aim to improve management practices to obtain a greater Nutrient Use Efficiency (NUE). From a chemical, biological, and ecophysiological perspective, at a reductionist level we have acquired a considerable mechanistic understanding about the N cycle, the varied N chemical forms, microbial interactions and physiology of crop uptake. However, at a holistic level, we are far from obtaining an adequate understanding of the myriad of multi-level cropping system, genetic, socioeconomic, environmental, and ecological interactions that have an effect on the N cycle and NUE. Here, based on a selected review of the literature, we provide a perspective on the potentials to increase the NUE of vegetable crops, by adopting a range of best management practices and by highlighting some of the N x system interactions that may be considered to better understand the complex dynamics of the N cycle, to optimize the NUE of vegetable crops, and to explore alternatives to the reliance on the use of synthetic N sources.

Although jojoba (Simmondsia chinensis) has been cultivated for years, information on its N re-quirements is limited. A 6-year study of mature jojoba plants grown under field conditions with an intensive management regime evaluated the effect of N-application rate on plant nutrient status, growth and productivity, and nitrate accumulation in the soil. Five levels of N application were tested: 50, 150, 250, 370 and 500 kg N ha-1. The fertilizers were provided all along the growing season via subsurface drip irrigation system. Leaf N concentration, in both spring and summer, reflected the level of N applied. Diagnostic leaf (youngest leaf that has reached full size) concentration of 1.3% N was identified as the threshold for N deficiency. Increasing rates of N application resulted in higher P levels in young leaves. Plant K status, as reflected by leaf analysis, was not affected by N treatment but was strongly affected by fruit load. Vegetative growth was inhibited when only 50 kg N ha-1 was applied. Soil analysis at the end of the fertilization season showed substantial accumulation of nitrate for the two highest application rates. Considering productivity, N costs, and environmental risk, 150 kg N ha-1 is the recommended dosage for in-tensively grown jojoba. N deficiencies can be identified using leaf analysis and excess N can be detected by soil sampling toward the end of the growing season. These results and tools will fa-cilitate precise N fertilization in intensive jojoba plantations.

Shrubs are a significant component of urban vegetation residing in parks, but they experience various influences of biotic and abiotic agents, among which aphids play an important role. In this work, the effect of aphid colonization on three shrub species in urban environment was examined. Fourteen parameters have been analyzed, describing photosynthetic pigment content and gas exchange to carbon, nitrogen, and hydrogen partition. While no significant effect of colonization was found on photosynthetic pigment parameters, the effect was significant on gas exchange parameters. The strongest effect aphid colonization achieved on nitrogen partition and C/N ratio, parameters that could be suggested in further similar studies. All parameters were classified in two groups according to principal component analysis, suggesting correlation between nitrogen and carbon content, C/N ratio, measured gas exchange parameters and chlorophyll a content. The ratio between net photosynthesis and dark respiration (A/K) was in the second group, suggesting that this parameter provide additional information on the effect of aphid colonization, and deserve special attention in further studies. There were differences in reaction of examined shrub species, where the strongest reaction by gross primary productivity (GPP) achieved Hybiscus syriacus, and by nitrogen partition and C/N ratio Spirea trilobata and Cydonia japonica.

Rice production is a significant contributor to methane emissions, accounting for ap-proximately 11% of global anthropogenic emissions. However, methane emissions in rice fields could effectively be reduced by implementing proper management practices and careful cultivar selection. The impact of nitrogen fertilizers on methane emissions is mul-tifaceted, as these fertilizers enhance crop growth and influence the activity of me-thane-producing (methanogens) and methane-consuming microbes (methanotrophs), leading to complex outcomes in methane emissions. In this study, we used qPCR to quan-tify methanogens and methanotrophs using mcrA (methanogenesis-related gene) and pmoA (methane oxidation-related gene) primer sets under different nitrogen levels (0, 50, and 100%) and rice varieties. The results revealed that higher nitrogen input led to higher methanogen inhabitation in the rhizosphere. Additionally, the abundances of methano-gens and methanotrophs varied among the different rice varieties. Furthermore, it was observed that there may be an additive effect between the rice variety and nitrogen level used. These findings suggest that future breeding efforts should involve screening for me-thane-related microbes in rice cultivars adapted to low-nitrogen conditions. By identifying and selecting rice varieties that promote lower methanogen levels and higher metha-notroph inhabitation, significant steps can be taken to mitigate greenhouse gas emissions from rice cultivation.

Abstract: Rice production is a significant contributor to methane emissions, accounting for approximately 11% of global anthropogenic emissions. However, there is potential for effectively reducing methane emissions from rice fields through the implementation of proper management practices and careful cultivar selection. The impact of nitrogen (N) fertilizers on methane (CH4) emissions is multifaceted, as these fertilizers not only en-hance crop growth but also influence the activity of methane-producing microbes (Meth-anogens) and methane-consuming microbes (Methanotrophs), leading to complex out-comes in CH4 emissions. In this study, we utilized qPCR to quantify methanogens and methanotrophs using mcrA (methanogenesis-related gene) and pmoA (methane oxida-tion-related gene) primer sets under different nitrogen levels (0, 50, 100%) and rice varie-ties. The results revealed that higher nitrogen inputs led to higher methanogen inhabita-tion in the rhizosphere. Additionally, the abundances of methanogens and metha-notrophs varied among different rice varieties. Furthermore, through the analysis of two-way ANOVA, it was observed that there may be an additive effect between rice variety and nitrogen level. Furthermore, enhancing agronomic traits related to yield can reduce methanogen inhabitation. These findings suggest that future breeding efforts should in-volve the screening of methane-related microbes in rice cultivars adapted to low nitrogen conditions. By identifying and selecting rice varieties that promote lower methanogen lev-els and higher methanotroph inhabitation, we can take significant steps towards mitigating greenhouse gas emissions from rice cultivation.

Water pollutants removal by biomass adsorbent has been considered innovative and cost effective, thus commendable for application in industrial applications. However, certain important aspects have been overlooked by researchers, namely the efficiency in the operation time and pollutant removal. In this research, landfill leachate samples with organic components were treated using bentonite-enriched with sawdust augmented (SBR) process. By modifying the pH, the sawdust samples were categorized into three: the acidic, the alkaline, and the neutral. To bentonite samples, the pH-adjusted sawdust was added at 10%, 20%, and 30% amounts by mass respectively. At the optimum aeration rate of 7.5 L/min and contact period of 22 h, the treatment achieved 99.28% and 95.41% removal of COD and NH₃-N with bentonite respectively. For both pollutants, in the presence of sawdust, the removal reduced by about 17% with contact period reduced to 2 h which was a considerable achievement.

In the realm of cement production, clinker-producing factories emerge as both energy and material-intensive entities, emitting a substantial array of primary pollutants into the environment compared to their non-clinker producing counterparts. Our study delves into Ethiopian clinker-producing cement factories, unraveling the concentration of primary pollutants and their repercussions on neighboring communities. Venturing beyond mere statistics, we meticulously measured particulate matter (PM2.5 and PM10) and gaseous emissions (CO2, N2O, SO2) at various units within the cement factories and in nearby residential areas. The findings reveal an ambient air quality riddled with concern; PM2.5 levels ranged from 137 to 814 μg/m3, PM10 from 195 to 886 μg/m3 within the cement factories, and PM2.5 (113 to 196 μg/m3) and PM10 (125 to 453 μg/m3) in the adjacent village. Alarmingly, these particulate matter emissions exceeded the limits set by Ethiopian ambient air quality guidelines (150 μg/m3). Unraveling the health implications, respiratory diseases were notably high among individuals aged 25 to 60, followed closely by those aged 6 to 24. In contrast, the age groups 0–5 and > 61 exhibited lesser susceptibility, as infants and the elderly spent more time at home, thus reducing exposure to emissions. Our study underscores the urgent need for legal measures, calling for the establishment of buffer zones between cement factories and settlements. This proactive step, if enforced, holds the promise of mitigating cement particulate emissions and safeguarding the well-being of communities residing in proximity to these industrial giants.

Life cycle assessment (LCA) is being included formally in EcoDesign regulations. Especially product carbon footprint will be mandatory in Europe. However, life cycle impact assessment including global warming potential (GWP) in LCA is hampered by several challenges. One of these is lack of water vapor characterization indexes for GWP. A life cycle inventory profile for air transport fuel including water vapor emissions is evaluated with state-of-the-art practice, i.e. EF Method and ILCD 2011 Midpoint+ and neglecting water vapors high altitude GWP compared to carbon dioxide. Then the characterization factor in GWP100 for water vapor and alternate normalization for particulates are introduced. The results are compared. The main findings are that the EF method and ILCD both generate rather realistic results for Particulate Matter and Respiratory Inorganics mid-point indicators, respectively, but the amount of premature deaths should be better allocated to different specific emissions, and that water vapor may dominate the GWP100 result over the usual carbon dioxide. LCIA mid-points need measurable and understandable bases. The common knowledge of water vapor’s GWP100 should not be neglected in LCIA for air transport and beyond where relevant.

This work presents the dynamics of forest clearing in the Brazilian Amazon during the period 2006–2019 in which includes the approval of the new Brazilian Forest Code in 2012. The study was carried out in the Brazilian Amazon, Pará State and in the municipality of Novo Progresso (Pará State). The analysis was based on deforestation and fire hotspot datasets issued by the Brazilian Institute for Space Research (INPE), produced based on optical and thermal sensors onboard different satellites. Deforestation data was also used to assess greenhouse gas (GHG) emissions from the slash-and-burn practices. The work showed a good correlation between the occurrence of fires in the newly deforested area in the municipality of Novo Progresso and the slash-and-burn practices. The same trend was also observed in the Pará State, suggesting a common practice along the deforestation arch. The study indicated positive coefficients of determination of 0.72 and 0.66 between deforestation and fire occurrences for the municipality of Novo Progresso and Pará State, respectively. The increased number of fire occurrences in the primary forest suggests possible ecosystem degradation. Deforestation reported for 2019 surpassed 10,000 km2, a significant intensification comparatively higher than the previous ten years which was on an average of 6,760 km2. The steady increase of deforestation in the Amazon after 2012 has been a worldwide concern because of the forest loss itself as well as the massive GHG emitted in the Brazilian Amazon (295 million tons of net CO2 equivalent in the year 2019). Better correlation of deforestation and fires occurrences reported from satellite images confirmed the slash-and-burn practice and the secondary effect of deforestation, which degrades primary forest surrounding the deforested areas.

The mass composition of Particulate Matter (PM) with an aerodynamic diameter of 2.5 microns (PM2.5) in San Joaquin Valley (SJV) is dominated by ammonium nitrate (NH4NO3) which is a secondary pollutant. The goal of this research was the investigation of the relationship between emissions, meteorology and PM2.5 concentrations in Fresno for the winter season. It was found that the location of sites near emission sources such as freeways compared with residential sites strongly affected measured PM2.5 concentrations. It was found that although long-term trends showed declines in both emissions and PM2.5 concentrations there was substantial variability between the years in the PM2.5/emissions relationship. Much of the yearly variation in the relationship between emissions and PM2.5 concentrations can be attributed to yearly variations in weather, such as atmospheric stability, precipitation frequency and average wind speed. There are moderate correlations between PM2.5 concentrations and temperature differences between nearby surface stations at varying elevations which explains some of the daily and seasonal variation in PM2.5. Occurrence of precipitation was related to low PM¬2.5 although the higher wind speeds and lower atmospheric stability associated with precipitation likely explain some of the low PM2.5 as well as washout of PM.

Ti-aluminosilicate gels were used as supports for immobilization of Fe, Co and Ni oxides (5%) by impregnation, and synthesis of efficient photocatalysts in degradation of β-lactam antibiotic from water. Titanium oxide (1 and 2%) was incorporated into zeolite network by modifying the gel during the zeolitation process. The formation of the zeolite Y structure and its microporous structure were evidenced by X-ray diffraction and N2 physisorption. The structure, composition, reduction and optical properties were studied by X-ray difraction, H2-TPR, XPS, Raman, photoluminiscence and UV-Vis spectroscopy. The obtained results indicated a zeolite Y structure for all photocatalysts with tetra-coordinate Ti4+ sites. The immobilized metals from group VIII are both in the form of metal oxides such as Fe2O3, Fe3O4, CoO, Co3O4 , NiO and also in the me-tallic state (Fe0, Co0, and Ni0). A red shift of the absorption edge was observed in UV-Vis spectra of photocatalysts upon addition of Fe, Co or Ni species. The photocatalytic performances were evaluated in degradation of cefuroxime from water under visible light irradiation. The best results were obtained for iron immobilized photocatalysts. Scavenger experiments explained the photocatalytic results and their mechanisms. A different contribution of the active species to the photocatalytic reactions was evidenced.

Heterocycles are unique precursors for the synthesis of various pharmaceuticals and agrochemicals particularly those possessing N- or O- moieties. The development of methods to prepare heterocycles is of great importance in synthesis of organic compounds, especially the heterocycles which can be found in natural products. The synthesis of nitrogen and oxygen containing heterocycles viz. coumarins, dihydropyrimidinones, imidazoles, isoxazoles and benzimidazoles represented an attractive and demanding work for chemists as these nucleus has found extensive applications in several fields such as material science, analytical chemistry and most importantly in medicinal chemistry. Organic synthesis has been attracted towards the development of new environmental friendly procedures to achieve the goals of green chemistry. The fundamental aspects of green chemistry are use of biocatalysts and environmental benign solvents under mild conditions. The present review article summarized the green synthetic methods and biological activities of nitrogen and oxygen containing heterocycles.

Biological nitrogen fixation (BNF) by symbiotic bacteria plays a vital role in sustainable agriculture. However, current quantification methods are often expensive and impractical. This study explores the potential of Raman spectroscopy, a non-invasive technique, for rapid assessment of BNF activity in soybeans. Raman spectra were obtained from soybean plants grown with and without rhizobia bacteria to identify spectral signatures associated with BNF. δN15 isotope ratio mass spectrometry (IRMS) was used to determine actual BNF percentages. Partial least squares regression (PLSR) was employed to develop a model for BNF quantification based on Raman spectra. The model explained 80% of the variation in BNF activity. To enhance the model's specificity for BNF detection regardless of nitrogen availability, a subsequent elastic net (Enet) regularization strategy was implemented. This approach provided insights into key wavenumbers and biochemicals associated with BNF in soybeans.

Chloride (Cl-) is applied in coffee in rates as a “macronutrient” due that potassium (K+) is one of the most demanded nutrients by the coffee plant, and the potassium muriate (KCl) bases fertilizer is one the most used by the coffee growers. Does not exist scientific evidence that addresses the question regarding with which is the influences of the Cl- applied in the K fertilization base on MOP on coffee growth, nutrient uptake, and nitrogen use efficiency (NUE). Over four years, two trials were conducted on greenhouse and field conditions to address these questions. The trials set up were designed to test the influence of increased Cl- and reduced S rates on biomass accumulation, nutrient uptake, and NUE. A significant effect of the Cl- rates on growth was observed under greenhouse conditions but a non-significant effect on yield under field conditions. Cl- and S significantly influence the NUE in coffee. The result allows us to conclude that Cl- rates need to be balanced with S rates and that Cl- applied as a macronutrient can improve the NUE in coffee when those rates do not exceed 180 mg. L-1 Cl- and 80 mg.L-1 S in the greenhouse and 150 kg.ha-1.year-1 Cl- and 50 kg. ha-1.year-1 S in field conditions. In practical terms, coffee farmers need to balance the K base fertilizers sources to improve the nutrient use efficiency, especially the NUE.