Based on the dynamic strength variation mechanism of concrete under complex loading conditions, two approaches were devised: numerical testing and CT scanning, guided by the principle of minimizing energy dissipation. A methodology for calculating concrete's failure area and measuring its strength was developed. The analysis delves into the mechanisms behind failure patterns and variations in concrete specimen strength, focusing on crack initiation, development, and the resultant failure surface formed by crack propagation, along with the stress distribution in concrete specimens subjected to diverse loading conditions. Through evaluating the strength and computed failure area of concrete specimens, it is evident that the loading method influences both the strength and failure area of concrete specimens. In general, a larger failure area correlates with a higher measured strength.

The objectives of the study were to determine the spatial rate of CO₂ flux (Net Ecosystem Exchange) and soil moisture in a wetland ecosystem applying Sentinel-1 IW (Interferometric Wide) data of VH (Vertical Transmit/Horizontal Receive—cross polarization) and VV (Vertical Transmit/Vertical Receive—like polarization) polarization. In-situ measurements of carbon flux, soil moisture, and LAI (Leaf Area Index) were carried out over the Biebrza Wetland in north-eastern Poland. The impact of soil moisture and LAI on backscattering coefficient (σ°) calculated from Sentinel-1 data showed that LAI dominates the influence on σ° when soil moisture is low. The models for soil moisture have been derived for wetland vegetation habitat types applying VH polarization (R² = 0.70 to 0.76). The vegetation habitats: reeds, sedge-moss, sedges, grass-herbs, and grass were classified using combined one Landsat 8 OLI (Operational Land Imager) and three TerraSAR-X (TSX) ScanSAR VV data. The model for the assessment of Net Ecosystem Exchange (NEE) has been developed based on the assumption that soil moisture and biomass represented by LAI have an influence on it. The σ° VH and σ° VV describe soil moisture and LAI, and have been the input to the NEE model. The model, created for classified habitats, is as follows: NEE = f (σ° Sentinel-1 VH, σ° Sentinel-1 VV). Reasonably good predictions of NEE have been achieved for classified habitats (R² = 0.51 to 0.58). The developed model has been used for mapping spatial and temporal distribution of NEE over Biebrza wetland habitat types. Eventually, emissions of CO₂ to the atmosphere (NEE positive) has been noted when soil moisture (SM) and biomass were low. This study demonstrates the importance of the capability of Sentinel-1 microwave data to calculate soil moisture and estimate NEE with all-weather acquisition conditions, offering an important advantage for frequent wetlands monitoring.

Natural gas hydrate, also known as combustible ice and mainly composed of methane, it is identified as the potential clean energy in the 21th century. Due to its large reserves, gas hydrate can ease problems caused by energy resource shortage and has gained attention around the world. In this paper, we focus on the exploration and development of gas hydrate as well as discussing its status and future development trend in China and abroad, then we analyze its opportunities and challenges in China from four aspects: resource, technology, economy and police with five forces model and PEST method. The results show, China has abundance gas hydrate resource; however the backward technologies and inadequate investment has seriously hindered the future development of gas hydrate, so China should establish relevant cooperation framework and intuitional arrangement to attract more investment as well as breaking through technical difficulties to make gas hydrate commercialization as soon as possible.

Plant leaf area index (LAI) is a key characteristic affecting field canopy microclimate. In addition to traditional professional measuring instruments, smartphone camera sensors have been used to measure plant LAI. However, when smartphone methods were used to measure conifer forest LAI, very different performances were obtained depending on whether the smartphone was held at the zenith angle or at a 57.5° angle. To validate further the potential of smartphone sensors for measuring conifer LAI and to find the limits of this method, this paper reports the results of a comparison of two smartphone methods with an LAI-2000 instrument. It is shown that both methods can be used to reveal the conifer leaf-growing trajectory. However, the method with the phone oriented vertically upwards always produced better consistency in magnitude with LAI-2000. The bias of the LAI between the smartphone method and the LAI-2000 instrument was explained with regard to four aspects that can affect LAI: gap fraction, leaf projection ratio, sensor field of view (FOV), and viewing zenith angle (VZA). It was concluded that large FOV and large VZA cause the 57.5° method to overestimate the gap fraction and hence underestimate conifer LAI, especially when tree height is greater than 2.0 m. For the vertically upward method, the bias caused by the overestimated gap fraction is compensated for by an underestimated leaf projection ratio.

Reasonable allocation of production plans and saving the overall electricity cost are crucial for large manufacturing conglomerates, which is an effective way for conglomerates to realize open-source and cost-saving. This paper develops an optimization model of off-site industrial production scheduling for enterprises in response to the problems of high electricity costs due to the irrational allocation of production schedules on the demand side of China's electric power and the difficulty of promoting industrial and commercial distributed photovoltaic (PV) projects in China. The model makes full use of the conditions of different PV resources and different electricity prices in different places to optimize the scheduling of industrial production in different places. The model is embedded with two sub-models of the electricity price prediction model and distributed photovoltaic kWh cost model to complete the model parameters, in which the electricity price prediction model utilizes the LSTM neural network. The integrated model is then solved by the particle swarm algorithm. To verify the effectiveness of the model in solving the problem of off-site production scheduling on the demand side of electricity, the research team researched two off-site pharmaceutical factories belonging to the same large pharmaceutical company. Finally, the research data were substituted into the model for solving, and it was concluded that the optimization model could significantly reduce the cost of electricity consumption of the enterprise by about 7.9 %.

Dynamic optical structural color is always desired in various display applications and usually involves active materials. Full-color generation, especially bi-directional full-color generation in both reflective and transmissive modes, without any active materials included has been rarely investigated. Herein, we demonstrate a scheme of bi-directional full-color generation based on a plasmonic metasurface modulated by rotation of the polarization angle of the incident light without varying the geometry and the optical properties of the materials and the environment where the metasurface resides. The metasurface unit cell consists of plasmonic modules aligning in three directions and is patterned in a square array. The metasurface structural color device generates full colors in both reflection and transmission. Based on the proposed polarization-dependent structural color, information encoding of three multiplexed animal images and quick-responsive (QR) codes is demonstrated to verify the efficient information encoding and decoding of the proposed scheme. The animals can be seen under different polarization incidence and the QR codes can be successfully decoded by the polarization rotation in transmission. The proposed bi-directional full-color generation metasurface has great potential in applications such as kaleidoscope generation, anti-counterfeiting, dynamic color display, and optical information encoding.

Accurate forecasting of icing thickness has a great significance for ensuring the security and stability of power grid. In order to improve the forecasting accuracy, this paper proposes an icing forecasting system based on fireworks algorithm and weighted least square support vector machine (W-LSSVM). The method of fireworks algorithm is employed to select the proper input features with the purpose of eliminating the redundant influence. In addition, the aim of W-LSSVM model is to train and test the historical data-set with the selected features. The capability of this proposed icing forecasting model and framework is tested through the simulation experiments using real-world icing data from monitoring center of key laboratory of anti-ice disaster, Hunan, South China. The results show that the proposed W-LSSVM-FA method has a higher prediction accuracy and it may be a promising alternative for icing thickness forecasting.

Image stitching is a crucial aspect of image processing. However, factors like perspective and environment often lead to irregular shapes in stitched images. Cropping or completion methods typically result in substantial loss of information. This paper proposes a method for rectifying irregularly images into rectangles using deformable meshes and residual networks. The method utilizes a convolutional neural network to quantify rigid structures of images. Choosing the most suitable mesh structure based on the extraction results, offering options such as triangular, rectangular, and hexagonal. Subsequently, the irregularly image, predefined mesh structure, and predicted mesh structure are input into a wide residual neural network for regression. The loss function comprises local and global, aimed at minimizing the loss of image information within the mesh and global target. This method not only significantly reduces information loss during rectification but also adapting to different images with various rigid structures. Validation on the DIR-D dataset shows this method outperforms state-of-the-art methods in image rectification.

Surface water distribution extracted from remote sensing data has been used in water resource assessment, coastal management, and environmental change studies. Traditional manual methods for extracting water bodies cannot satisfy the requirements for mass processing of remote sensing data; therefore, accurate automated extraction of such water bodies has remained a challenge. The histogram bimodal method (HBM) is a frequently used objective tool for threshold selection in image segmentation. The threshold is determined by seeking twin peaks, and the valley values between them; however, automatically calculating the threshold is difficult because complex surfaces and image noise which lead to not perfect twin peaks (single or multiple peaks). We developed an operational automated water extraction method, the modified histogram bimodal method (MHBM). The MHBM defines the threshold range of water extraction through mass static data; therefore, it does not require the identification of twin histogram peaks. It then seeks the minimum values in the threshold range to achieve automated threshold. We calibrated the MHBM for many lakes in China using Landsat 8 Operational Land Imager (OLI) images, for which the relative error (RE) and squared correlation coefficient (R2) for threshold accuracy were found to be 2.1% and 0.96, respectively. The RE and root-mean-square error (RMSE) for the area accuracy of MHBM were 0.59% and 7.4 km2. The results show that the MHBM could easily be applied to mass time-series remote sensing data to calculate water thresholds within water index images and successfully extract the spatial distribution of large water bodies automatically.

This paper analyzes and compares models for predicting average magnet losses in interior permanent-magnet motors with fractional-slot concentrated windings due to harmonics in the armature reaction (assuming sinusoidal phase currents). Particularly, loss models adopting different formulations and solutions to the Helmholtz equation to solve for the eddy currents are compared to a simpler model relying on an assumed eddy-current distribution. Boundaries in terms of magnet dimensions and angular frequency are identified (numerically and using an identified approximate analytical expression) to aid the machine designer whether the more simple loss model is applicable or not. The assumption of a uniform flux-density variation (used in the loss models) is also investigated for the case of V-shaped and straight interior permanent magnets. Finally, predicted volumetric loss densities are exemplified for combinations of slot and pole numbers common in automotive applications.

Open source software such as OpenDSS has given a lot of help to distribution network researchers and educators. With high penetration of distributed renewable energy resources into distribution network, tradition distribution steady state analysis software such as OpenDSS is faced with difficulty in handling distributed generators. Three-phase distributed generators are often modeled in sequence frame while unbalanced distribution network are usually modeled in phase frame. So a load flow in sequence-phase coupled frame is proposed to handle models described in both frames. Voltage controlled DGs which are difficult to cope with in OpenDSS are handled in proposed program. The steady state analysis platform is programmed with open source Modelica language and the main aim of this paper is to introduce an open source platform for active distribution network steady analysis include load flow and short circuit analysis which can be easily adopted and improved by other educators and researchers.

Coal gasification with carbon dioxide is a process for generating clean gaseous fuels and relieving greenhouse effect. Zhundong coal has high alkali and alkali earth metals (AAEMs) content, medium volatile and low ash in nature. Isothermal CO₂ gasification of char derived from Zhundong coal (R-char) and char from acid washing R-char (AR-char) are performed in thermo-gravimetric analyzer (TGA). The effect of AAEMs is investigated on the gasification behavior in the range of temperatures 1073 K to 1273 K. The carbon conversion increases rapidly with increasing reaction temperature and CO₂ concentration. R-char has high gasification rate and carbon conversion compared with AR-char. The accuracy of the free-model approach for calculating activation energy at different conversions is validated by compared with different kinetic models (volume reaction model, distributed activation energy model). Moreover, R-char gasification with CO₂ shows a compensation effect as the Arrhenius parameters (EA and k0) increase or decrease simultaneously.

Abstract: High step-up voltage gain nonisolated DC-DC converter have attracted much attention in photovoltaic, fuel cells and other renewable energy system applications. In this paper, by combining input current ripple-free boost cell with coupled-inductor voltage-doubler cell, an input current ripple-free high voltage gain nonisolated converter is proposed. In addition, passive lossless clamp circuit is adopted to recycle the leakage inductor energy and to reduce the voltage spike across the power switch. By utilizing voltage-doubler cell consisting of diode and capacitor, the voltage stress of switch is further reduced and the resonance between the leakage inductor and the stray capacitor of the output diode is eliminated. A low switch-on-resistance low-voltage-rated MOSFET can therefore be employed to reduce the conduction loss and cost. The reverse recovery loss of output diode is reduced, and the efficiency of converter can be improved. Furthermore, the proposed converter can achieve nearly zero input current-ripple and make the design of electromagnetic interference (EMI) filter easy. Steady state analysis and operation mode of the converter is performed. Finally, experimental results are presented to verify the analysis results of the proposed converter.

The literature offers limited information on the effect of obesity on the rate of force development, a critical parameter for mobility in older adults. The objectives of this study were; to explore the influence of obesity on RFD in older adults and to examine the association between this neuromuscular parameter and walking speed. 42 older adults were classified into two groups: the control group (CG, n=22; age=81.13±4.02 years; Body mass index (BMI)=25.13±3.35 kg/m²), and the obese group (OG, n=20; age=77.71±2.95 years; BMI=34.46±3.25 kg/m²). Walking speed (m/s) was measured using the 10-meter walking test. Neuromuscular parameters of the plantar flexors were evaluated during a maximal voluntary contraction test using a dynamometer. The RFD was calculated from the linear slop of the force – time curve in two phases: from the onset of the contraction to 50 ms (RFD50-100) and from 100 to 200 ms (RFD100-200). The gait speed was lower in the OG compared to the CG (p

For multi-sensor integrated systems, such as a mobile mapping system (MMS), data fusion at sensor-level, i.e., the 2D-3D registration between optical camera and LiDAR, is a prerequisite for higher level fusion and further applications. This paper proposes a line-based registration method for panoramic images and LiDAR point cloud collected by a MMS. We first introduce the system configuration and specification, including the coordinate systems of the MMS, the 3D LiDAR scanners, and the two panoramic camera models. We then establish the line-based transformation model for panoramic camera. Finally, the proposed registration method is evaluated for two types of camera models by visual inspection and quantitative comparison. The results demonstrate that the line-based registration method can significantly improve the alignment of the panoramic image and LiDAR datasets under either the ideal spherical or the rigorous panoramic camera model, though the latter is more reliable.

Microscopic vision plays an important role in automated micro-assembly. However, some uncertain factors in the assembly process, such as occlusion and stains can lead to the mistakes of feature extraction. Herein, to solve the problem, the deep learning techniques are introduced into the feature recognition tasks, focusing on the attention mechanism and visualizing CNNs for DL-based microscopic vision. The main contributions are summarized as follows: The CBAM attention mechanism is combined with the YOLOv5 algorithm to improve the accuracy and robustness of feature extraction. The micropart feature occlusion experiment results show that at 70% occlusion degree, YOLOV5-CBAM can reach 97.9% [email protected], which is 4.6% higher than the original one. Visualization analysis of DL-based model is conducted using Grad-CAM to make the decision result more transparent and avoid potential visual detection risks during assembly. The heatmap matching degree between GT area and high-light area is increased by 27.81% on average, which further verify the effectiveness of attention mechanism in micropart feature localization. Additionally, micropart surface stain and droplet quality classification models based on ResNet50 are trained to replace the manual sorting. The visual results are consistent with human eye discernment and judgement, confirming the reliability of parts and droplets sorting.

The experiences gathered during the past 30 years support the operational use of irrigation scheduling based on frequent multi-spectral image data. Currently, the operational use of dense time series of multispectral imagery at high spatial resolution makes monitoring of crop biophysical parameters feasible, capturing crop water use across the growing season, with suitable temporal and spatial resolutions. These achievements, and the availability of accurate forecasting of meteorological data, allow for precise predictions of crop water requirements with unprecedented spatial resolution. This information is greatly appreciated by the end users, i.e. professional farmers or decision-makers, and can be provided in an easy-to-use manner and in near-real-time by using the improvements achieved in web-GIS methodologies. This paper reviews the most operational and explored methods based on optical remote sensing for the assessment of crop water requirements, identifying strengths and weaknesses and proposing alternatives to advance towards full operational application of this methodology. In addition, we provide a general overview of the tools which facilitates co-creation and collaboration with stakeholders, paying special attention to these approaches based on web-GIS tools.

Three kinds of inorganic alkali are introduced into tetraethylenepentamine (TPEA) and polyethyleneimine (PEI) modified MCM-41 as the CO2 adsorbents. FT-IR and TGA are used to characterize the surface groups and the thermal stability of adsorbents. Chemical titration method is used to measure the alkali amounts of adsorbents. Thermo-gravimetric analysis with 10%CO2/N2 as the simulated flue gas is used to test the CO2 adsorption performance of adsorbents. The results show that all three kinds of inorganic alkali containing adsorbents exhibit promoted CO2 adsorption capability than traditional TPEA and PEI modified samples. Ca(OH)2 and PEI modified samples exhibit the highest adsorption capacity and stable regeneration property. The introduction of inorganic alkali changes the chemical adsorption mechanism between CO2 and increases the effective alkali amounts due to its hydroxyl groups. The CO2 adsorption capacities have a linear dependence relation with the alkali amounts of adsorbents, indicating that alkali amount is a critical factor for novel adsorbents exploring.

More and more works are using machine learning techniques while adopting supervisory control and data acquisition (SCADA) system for wind turbine anomaly or failure detection. While parameter selection is important for modelling a wind turbine’s health condition, only a few papers have been published focusing on this issue and in those papers interconnections among sub-components in a wind turbine are used to address this problem. However, merely the interconnections for decision making sometimes is too general to provide a parameter list considering the differences of each SCADA dataset. In this paper, a method is proposed to provide more detailed suggestions on parameter selection based on mutual information. Moreover, after proving that Copula, a multivariate probability distribution for which the marginal probability distribution of each variable is uniform is capable of simplifying the estimation of mutual information, an empirical copula based mutual information estimation method (ECMI) is introduced for an application. After that, a real SCADA dataset is adopted to test the method, and the results show the effectiveness of the ECMI in providing parameter selection suggestions when physical knowledge is not accurate enough.

For offshore wind power generation, accessibility is one of the main factors that has great impact on operation and maintenance due to constraints on weather conditions for marine transportation. This paper presents a framework to explore the accessibility of an offshore site. At first, several maintenance types are defined and taken into account. Next, a data visualization procedure is introduced to provide an insight into the distribution of access periods over time. Then, a rigorous mathematical method based on finite state Markov chain is proposed to assess the accessibility of an offshore site from the maintenance perspective. A five-year weather data of a marine site is used to demonstrate the applicability and the outcomes of the proposed method. The main findings show that the proposed framework is effective in investigating the accessibility for different time scales and is able to catch the patterns of the distribution of the access periods. Moreover, based on the developed Markov chain, the average waiting time for a certain access period can be estimated. With more information on the maintenance of an offshore wind farm, the expected production loss due to time delay can be calculated.

The vast array of interconnected microbes across earth’s ecosystems and within holobionts has been called the “Internet of Microbes.” Research into the fundamental microbial properties has demonstrated that bacteria and archaea are masters of energy and information collection, storage, transformation, and dissemination using both “wired” and wireless (at a distance) capacities. These features suggest that microbes are quantum entangled within and between earth’s holobionts, and that specific tools affecting energy and information functions could provide an effective strategy for managing microbial populations. Microbes use four critically important microbial networking functions (sound, light, electricity, and magnetism). This narrative review focuses on microbial management based on two of the four: sound and light (as well as related vibrations). These are examined as: 1) tools for managing microbial populations, 2) tools to support new technologies, and 3) tools for healing humans and other holobionts. Given microbial sensitivity to sound, light, and vibrations, it is critical that microbial populations and microbe-laden holobionts are protected from potentially damaging exposures. We conclude that sound, light, and vibrations are useful therapeutic tools that can help support useful microbial populations and help to address ongoing challenges of holobiont disease.

Isothermal interrupted hot compression tests of 5754 aluminum were conducted on Gleeble-3500 thermo-mechanical simulator at temperature 350 °C and 450 °C, strain rate 0.1 s-1 and 1s−1. These tests simulated flat rolling to investigate how softening behaviors respond to controlled parameters, such as deformation temperature, strain rate and delay times. This data allowed the parameters for the hot rolling process to be optimized. The delay times during interrupted compression vary between 5s and 60s. The dynamic softening at each pass and metadynamic recrystallization at the intervals of deformation passes were analyzed in detail. 0.2% offset yield strength is applied to calculate the softening fraction undergoing metadynamic recrystallization. A kinetic model was developed to describe metadynamic recrystallization behaviors of the hot deformed 5754 aluminum alloy. Furthermore, the time constant for 50% recrystallization was expressed as functions related to the temperature and the strain rate. The experimental and calculated results were found to be in close agreement, which verified the developed model.

In the modern power grid, characterized by the increased penetration of power electronics and extensive utilization of renewable energy, inverters-based power plants play a pivotal role as the principal interface of renewable energy sources (RESs) and the grid. Considering the stability characteristics of grid-following (GFL) inverters when the grid is relatively weak, the application of grid-forming (GFM) controls becomes imperative to enhance the stability of the entire power plant. Thus, there is an urgent need for suitable and effective models to study the interaction and stability of the paralleled inverters employing GFL and GFM controls. Thus, the small-signal modeling with full-order state space model and eigenvalues analysis is presented in this paper. First, the small-signal state-space model of the individual GFL and GFM inverters is obtained considering the control loop, interaction, reference frame, transmissions, and time delays. Then, the models of the individual inverter are extended to the hybrid inverters to study the effects of the GFM inverters on the small- signal stability of the entire system. And, the impacts of the inertia and damping are analyzed by the eigenvalues of the state-transition matrix. Case comprising three parallel GFL inverters and two GFL inverters with one GFM inverter, respectively, are studied to examine the effectiveness and accuracy of the model. Finally, the stability margin obtained from the eigenvalue analysis of the entire system is verified by time-domain simulations.

Mutual exclusion algorithms are at the heart of concurrent, distributed/parallel, real-time and operating systems. It is well-known that such algorithms are very difficult to analyze and in the literature different conjectures about starvation-freedom and the number of by-passes (also said the overtaking factor), which in turn affects the (hopefully) bounded waiting time that a process competing for entering the critical section has to suffer before accessing the shared resource, have been formulated for specific algorithms. This paper proposes a novel modelling approach based on Timed Automata and the Uppaal toolset, which proves effective for studying all the properties of a mutual exclusion algorithm for N≥2 processes, by exhaustive model checking. Although the approach, as already confirmed by similar experiments reported in the literature, is not scalable due to state explosion problems, and can be practically applied until N≤5, it is of great value for revealing true properties of analyzed algorithms. For dimensions N>5 the statistical model checker of Uppaal can be used which, although based on simulations, can confirm properties by estimations and probabilities. The paper describes the proposed modelling and verification method and applies it to several mutual exclusion algorithms, thus retrieving known properties but also showing new results about properties often studied only by peer-review and intuitive reasoning.

The atmospheric lightning is one of the natural disasters which need to be considered in the sustainable development. The National Remote Sensing Centre (NRSC) has installed 46 lightning detection sensors (LDS) across the country. These sensors work in radio frequencies having their detection range up to 1000 km with more than 98% detection efficiency within 300 km range. The network is put in a way that sensors have about 50% sensor-to-sensor overlap in their detection ranges to enable high geolocation accuracy and maintain redundancy. The NRSC-LDS network (LDSN) estimates the current associated with each cloud to ground (CG) lightning flash which can be utilized for the risk assessment. The current estimates from one network to the other need to be inter-calibrated and harmonized. Present study compares the LDSN current estimates with Lightning Location Network (LLN) estimates and results are discussed with their impact on the estimation of vulnerable zones. A case study of lightning-induced fire event is presented to showcase the importance of the currents associated with lightning for future planning.

The development of accurate dynamic battery pack models for electric vehicles (EVs) is critical for the ongoing electrification of the global automotive vehicle fleet, since these serve as a key element in the energy performance of an EV powertrain system. The Equivalent Circuit Model (ECM) technique at the cell level is commonly employed for this purpose, combining accuracy and efficiency in the representation of battery operation within the broader powertrain system. In this study, a second-order ECM model of a battery cell is being developed using Modelica, an equation-based modeling language. Parameter lookup tables at multiple levels of state of charge (SoC), extracted from Li-ion battery cells with 4 different commonly used cathode materials, have been utilized. This approach allows for a representation of the battery systems that are used in a wide range of commercial EV applications. To verify the model, an integrated EV model is developed and simulation results of the FTP75 driving cycle have been compared against an equivalent application in MATLAB Simulink. The findings demonstrate a close match between the results obtained from both software across different system points. Specifically, the maximum deviation of SoC is limited to 0.08% and the maximum value of relative voltage deviation is 1.4%. The verified model enables the exploration of multiple possible architecture configurations of EV powertrains with Modelica.

This paper is aimed at studying the temporal evolution of the surface displacements occurred over the past few years in the ocean-reclaimed platforms of the Shanghai megacity (China), which are mainly ascribable to consolidation processes of large dredger fills and alluvial deposits. With respect to previous analyses carried out over the same area, this work provides a joint multi-platform differential interferometry synthetic aperture radar (DInSAR) analysis, based on the application of the advanced Small BAseline Subset (SBAS) algorithm. This led us to retrieve long-term deformation time-series that are helpful for a better understanding of the on-going deformation phenomena. To this aim, we have exploited two sequences of SAR data collected by the ASAR/ENVISAT and by the COSMO-SkyMed (CSK) sensors, respectively, spanning the whole time period from 2007 to 2016. Unfortunately, the large time gap (of about three years) existing between the available ASAR/ENVISAT and CSK datasets gave rise to additional difficulties for their combination. Nevertheless, this problem has been faced by benefiting from the knowledge of a time-dependent model describing the temporal evolution of the expected deformations affecting the Shanghai ocean-reclaimed platforms.

For a wide field of view (FoV) wavefront coding athermalized infrared imaging system with a single decoding kernel, the off-axis aberration tends to cause artefacts. In order to correct off-axis aberration, many pieces of lenses will reduce the transmission efficiency and increase the weight and cost. To meet requirements for wide FoV, wide operating temperature and low weight of infrared imaging systems, this paper reports a wide-FoV wavefront coding athermalized infrared imaging system with a two-piece lens. Its principle, design, manufacture, measurement and performance validation are successively discussed. This paper constructs an optimization problem which maximizes the weighted mean of PSF consistency for both the FoV and operating temperature range. The two-piece lens contains four surfaces, where three aspheric surfaces are introduced to reduce optical off-axis aberrations and a cubic surface is introduced to achieve athermalization. The optical phase mask containing an aspheric surface and a cubic surface is manufactured by nano-metric machining of ion implanted material(NiIM). Experimental results validate that our wide-FoV wavefront coding athermalized infrared imaging system has a full FoV of 26.10° and an operating temperature over -20°C to +70°C.

Polyphenols and fermentable fibers have shown favorable effects on gut microbiota composition and metabolic function. However, few studies have investigated whether combining multiple fermentable fibers or polyphenols may have additive beneficial effects on gut microbial states. Here, an in vitro fer-mentation model, seeded with human stool combined from 30 healthy volunteers, was supplemented with blends of polyphenols (PP), dietary fibers (FB) or their combination (PPFB) to determine influence on gut bacteria growth dynamics and select metabolite changes. PP and FB blends independently lead to significant increases in the absolute abundance of select beneficial taxa, namely Ruminococcus bromii, Bifidobacterium spp., Lactobacillus spp. and Dorea spp. Total short chain fatty acid concentrations, relative to non-supplemented control (F), increased significantly with PPFB and FB supplementation, but not PP. Indole and ammonia concentrations decreased with FB and PPFB supplementation, but not PP alone while increased antioxidant capacity was only evident with both PP and PPFB. These findings demonstrated that, while the independent blends displayed selective positive impacts on gut states, combination of both blends provided an additive effect. The work outlines the potential of mixed substrate blends to elicit a broader positive influence on gut microbial composition and function to build resiliency toward dysbiosis.

The performance of OpenFOAM in strong scaling tests on HPC systems with AMD EPYC processors exhibits a pronounced superlinear speedup. Simple test cases show superlinear speedups of over 300%, which significantly impacts the efficient use of computing resources. With the last generation of HPC architectures, a superlinear speedup of about 10% to 20% was well expected and accepted by CFD users. The measured superlinear speedup is much more pronounced and withstands the communication overhead to even larger scales. A detailed performance analysis of OpenFOAM follows, employing various High-Performance Computing (HPC) architectures, including AMD, ARM and Intel systems. The performance metric FVOPS (Finite VOlumes solved Per Second) is introduced to compare the performance of Computational Fluid Dynamics (CFD) applications when varying the grid size, as occurs in a strong scaling test. The achievable FVOPS depends on various factors, including the simulation type, boundary conditions, and especially the grid size of a use case. Analysing FVOPS on a single node level with varying grid size shows a significant difference in performance and cache utilization, which explains the large superlinear speedups seen in the strong scaling tests. Furthermore, FVOPS can be used as a simple benchmark to determine the optimal number of grid elements per rank to simulate a given use case at peak efficiency on a given platform, resulting in time, energy, and cost savings. The FVOPS metric also facilitates the direct comparison between different HPC architectures. The tests using AMD, ARM, and Intel processors show a peak in performance when employing around 10,000 grid elements per core. The presence of a large L3 cache on AMD processors is particularly advantageous, as indicated by L3 cache miss rates observed on AMD EPYC processors. Our results suggest that future HPC architectures with larger caches and higher memory bandwidth would benefit the CFD community.

With the development of higher voltage power grid, the high and low voltage parallel loops are emerging, which lead to energy losses, even threaten the security and stability of power system. The multi-infeed HVDC configurations widely appearing in AC/DC interconnected power system make this situation even worse. Aimed at energy saving and system security, a decision optimization method for power grid operating condition with high and low voltage parallel loops is proposed in this paper. Firstly, considering hub substation distribution and power grid structure, parallel loop opening schemes are generated with GN algorithm. Then, candidate opening schemes are preliminarily selected from all these generated schemes based on a filtering index. Finally, with the influence on power system security, stability and operation economy in consideration, an evaluation model for candidate opening schemes is founded based on analytic hierarchy process (AHP). And a fuzzy evaluation algorithm is used to find the optimal scheme. Simulation results of New England 39-bus system and an actual power system validate the effectiveness and superiority of this proposed method.

In this paper, a relatively new hyper convolution spectra for characterization liquid, viscoelastic and solid samples is presented. Special attention is paid to the biophysical characterization of epithelial tissues and early detection of cancer of the skin, cervix, colon, and oral cavity. The method is based on the use of two types of white light, diffuse and polarized, from the same LED light sources. Based on the subtraction of the intensity values of these two lights and using the hyper convolution algorithm, the ratio of paired and unpaired electrons of tissue is obtained. This ratio correlates well with the state of the tissue: normal, irritating, precancerous, and cancerous. First, a proof-of-concept studies were performed, and later clinical studies on samples from one thousand two hundred fifteen people were performed. It showed that hyper Opto-Magnetic Imaging Spectroscopy (OMIS) can detect epithelial tissue cancers with an accuracy of 85-96%. Bearing in mind that the OMIS method also acquires the biophysical characteristics of the deeper skin layers (epidermis, basement membrane, dermis) by analysing convolution spectra of RGB channels of both diffuse and polarized white light, it is possible to apply this method in cosmetics (skin hydration, collagen, and elastin states, etc.). During OMIS applications, we noticed places where improvements could be made to increase method’s accuracy using advanced machine learning methodologies.

The work aims to improve the battery performance in hybrid electric vehicles (HEVs) by reducing the vehicle speed. We develop a specific protocol for managing battery use and optimizing the energy consumption rate to achieve this goal. The protocol automatically controls the driving operation, avoiding incompatible driving patterns with energy-saving mode and performance improvement. The protocol is submitted to a simulation process to predict the energy rate lowering and battery performance enhancement. The proposed protocol applies to any hybrid electric vehicle type and route conditions since it uses vehicle mass, drag and rolling coefficients, and road slope as variable parameters to determine the minimum energy consumption rate. We run experimental tests to validate the simulation data and the proposed protocol. Furthermore, the protocol applies to variable starting vehicle speeds, from 10 to 50 km/h, corresponding to the current driving patterns, sport, normal, and eco, set up by car manufacturers. A reduction of 10% in vehicle speed in urban and peripheral routes achieves a minimum energy rate, enhancing battery management. Current vehicle speed shows a deviation from optimum management of 18% while applying the vehicle speed reduction limits the deviation to 0.2%. Experimental results show a good agreement with simulation data with 94% accuracy. We tested the protocol for urban and peripheral routes with maximum vehicle speed limits of 60 and 90 km/h.

Daily maximum surface air temperature (Tamax) is a crucial factor for understanding complex land surface processes under rapid climate change. Remote detection of Tamax has widely relied on the empirical relationship between air temperature and land surface temperature (LST), a product derived from remote sensing. However, little is known about how such a relationship is affected by the high heterogeneity in landscapes and dynamics in seasonality. This study aims to advance our understanding of the roles of land cover and seasonal variation in the estimation of Tamax using the MODIS (Moderate Resolution Imaging Spectroradiometer) LST product. We developed statistical models to link Tamax and LST in the middle and lower reaches of the Yangtze River in China for five major land-cover types (i.e., forest, shrub, water, impervious surface, cropland, and grassland) and two seasons (i.e., growing season and non-growing season). Results show that the performance of modeling the Tamax-LST relationship was highly dependent on land cover and seasonal variation. Estimating Tamax over grasslands and water bodies achieved superior performance; while uncertainties were high over forested lands that contained extensive heterogeneity in species types, plant structure, and topography. We further found that all the land-cover specific models developed for the plant non-growing season outperformed the corresponding models developed for the growing season. Discrepancies in model performance mainly occurred in the vegetated areas (forest, cropland, and shrub), suggesting an important role of plant phenology in defining the statistical relationship between Tamax and LST. For impervious surfaces, the challenge of capturing the high spatial heterogeneity in urban settings using the low-resolution MODIS data made Tamax estimation a difficult task, which was especially true in the growing season.

The mineralogical indices, e.g., Quartz Index (QI), Carbonate Index (CI), Mafic Index (MI) for ASTER multispectral thermal infrared (TIR) data have been applied to various geological materials. The indices are proved to be robust in extracting geological information at the local scale. Considering the relatively narrow spatial coverage of each ASTER scene compared to LANDSAT, many scenes are needed when mosaicking the images to be mapped at regional scales. We develop a system to search ASTER data for a target area given the vast and expanding ASTER data archive. The data is then conditioned, prioritized, and the indices are calculated before finally mosaicking the imagery. The maps of the indices covering the very wide region of the central Tibetan Plateau are produced with this system. The characteristic features of the indices relating to their geology in the study area are analyzed and discussed. Many interesting lithological and structural information that are not currently well understood in the central Tibetan Plateau, the highest and most extensive plateau in the world, with an average elevation of over 4,500 meters above sea level, for example, distributions of the mafic-ultramafic rocks along the suture zones, the quarzitic and marine sedimentology accreted to the Eurasian continent and sulfate layers related to the Tethys and neo-Tethys geological setting can be retrieved from the processed ASTER images.

Using coherent optical detection and digital signal processing, laser phase noise and equalization enhanced phase noise can be effectively mitigated using the feed-forward and feed-back carrier phase recovery approaches. In this paper, theoretical analyses of feed-back and feed-forward carrier phase recovery methods have been carried out in the long-haul high-speed n-level phase shift keying (n-PSK) optical fiber communication systems, involving a one-tap normalized least-mean-square (LMS) algorithm, a block-wise average algorithm, and a Viterbi-Viterbi algorithm. The analytical expressions for evaluating the estimated carrier phase and for predicting the bit-error-rate (BER) performance (such as the BER floors) have been presented and discussed in the n-PSK coherent optical transmission systems by considering both the laser phase noise and the equalization enhanced phase noise. The results indicate that the Viterbi-Viterbi carrier phase recovery algorithm outperforms the one-tap normalized LMS and the block-wise average algorithms for small phase noise variance (or effective phase noise variance), while the one-tap normalized LMS algorithm shows a better performance than the other two algorithms for large phase noise variance (or effective phase noise variance). In addition, the one-tap normalized LMS algorithm is more sensitive to the level of modulation formats.

Multimodal remote sensing data classification can enhance the model’s ability to distinguish land features through multimodal data fusion. In this context, how to help models understand the relationship between multimodal data and target tasks is the focus of researchers. Inspired by human feedback learning mechanisms, causal reasoning mechanisms, and knowledge induction mechanisms, this paper integrates causal learning, reinforcement learning, and meta learning into a unified remote sensing data classification framework and proposed the causal meta-reinforcement learning (CMRL). First, based on feedback learning mechanisms, we have overcome the limitations of traditional implicit optimization of fusion features and customized a reinforcement learning environment for multimodal remote sensing data classification tasks. Through feedback interactive learning between agents and the environment, we help them understand the complex relationships between multimodal data and labels, thereby achieving full mining of multimodal complementary information. Second, based on the causal inference mechanism we designed causal distribution prediction action, classification reward, and causal intervention reward, capturing pure causal factors in multimodal data and cutting off false statistical associations between non-causal factors and class labels. Finally, based on the knowledge induction mechanism, we designed a bi-layer optimization mechanism based on meta-learning. By constructing a meta training task and meta validation task simulation model in the generalization scenario of unseen data, we helped the model induce cross-task shared knowledge, thereby improving its generalization ability for unseen multimodal data. The experimental results on multiple sets of multimodal datasets show that the proposed method achieved state-of-the-art performance in multimodal remote sensing data classification tasks.

In this work modeling and analysis of an integrated opto-fluidic sensor, with a focus on achievement of single mode optical confinement and continuous flow of micro particles in the microfluidic channel for Lab-on-a Chip (LOC) sensing application is presented. This sensor consists of integrated optical waveguides, microfluidic channel among other integrated optical components. A continuous flow of micro particles in a narrow fluidic channel is achieved by maintaining the two sealed chambers at different temperatures and by maintaining a constant pressure of 1Pa at the centroid of narrow fluidic channel geometry. The analysis of silicon on insulator (SOI) integrated optical waveguide at an infrared wavelength of 1550nm for single mode sensing operation is presented. The optical loss is found to be 0.0005719dB/cm with an effective index of 2.2963. The model presented in this work can be effectively used to detect the nature of micro particles and continuous monitoring of pathological parameters for sensing applications.

Urban rail transit hub platform is the most important area for passenger flow distribution. In order to calculate passenger flow volume in platform and evaluate platform service level during rush hours, this paper presents a method for modeling and simulation of passenger flow distribution in platform. Passenger flow distribution model (PFDM) is proposed based on the basic analysis and the superposition principle of passenger flow. Simulation design for PFDM is proposed by Anylogic, which contains simulation process and simulation model. Experiment results show that PFDM and simulation design are effective and accordant with the reality scenario, and the simulation precision is comparatively ideal. This research could provide a beneficial reference for train scheduling and operation management under the viewpoint of traffic safety and service level.

The necessity for precise and current data concerning the dynamics of land cover change in Indonesia is crucial for efforts to reduce natural vegetation cover due to agricultural expansion. The functionality of monitoring systems that incorporate Terra-MODIS is currently compromised by the limited availability of data for the immediate future. This study seeks to assess the potential of VIIRS satellite imagery in developing an early warning system for monitoring vegetation cover change in Indonesia. The Normalized Differential Open Area Index (NDOAI) computed from the 8-day’ VIIRS data was employed to detect changes in vegetation cover based on pixel-by-pixel subtraction in the NDOAI data time series. Evaluating the pixel-level accuracy of change detection is complicated due to the fact that we evaluate a change map at a coarser resolution than the Landsat-based reference map. The results revealed that increasing the threshold percentage is associated with improved accuracy. In change detection, there is often a trade-off between accuracy and sensitivity. A threshold that is too low may result in false positives, while a threshold that is too high may lead to missed changes. This study demonstrates that when a threshold value of less than 20% is applied, Landsat can identify vegetation cover changes at an earlier stage. Conversely, when a threshold value greater than 20% is employed, VIIRS will detect the change 4.5 days earlier than Landsat. Additionally, VIIRS is capable of detecting changes 25.4 days and 54.8 days faster than Landsat, respectively, when using thresholds of 40% and 75%.

To improve the adaptability of aerial reflective opto-mechanical structures to low-temperature environments, an optimized thermal control design is proposed. Firstly, the relationship be-tween conventional heating methods and axial/radial temperature differences of mirrors with different shapes is analyzed. Based on heat transfer analyses, it is pointed out that optimized thermal control design is necessary to ensure the temperature uniformity of the fused silica mirror and take into account the temperature level when working in low temperature environ-ments. A thermal control scheme based on temperature negative feedback variable power zone heating is proposed for the characteristics of aerial electro-optics systems. Using the thermal control scheme at low temperatures ensures that the average temperature of the mirror fluctu-ates slowly and slightly around 20℃. At the same time, the temperature differences within a mirror and between the primary mirror and the secondary mirror can be controlled within 5℃. Thereby, satisfactory image quality is obtained.

As a representative of Exponential Organizations, MI went from obscurity to the Fortune 500 in just ten years. Mi's success is inextricably linked to its outstanding business model. This paper summarizes the elements of MI's business model from four perspectives: value proposition, value creation, value delivery, and value capture, as well as its measures for developing into an exponential organization. Expecting to provide theoretical references for the transformation and upgrading of manufacturing organizations.

This article describes the history of research and development of surface-penetrating radar, starting from the 60s in the USSR, and ending today in Russia and neighboring states formed after the collapse of the USSR. The outstanding role played in the initial period of this technology development by Prof. M.I. Finkelstein and his colleagues is highlighted. Their research had a significant impact on subsequent developments in modern Russia and the neighboring countries.

Aerial image classification has become popular and has attracted extensive research efforts in recent decades. The main challenge lies in its very high spatial resolution but relatively insufficient spectral information. To this end, spatial-spectral feature extraction is a popular strategy for classification. However, parameter determination for that feature extraction is usually time-consuming and depends excessively on experience. In this paper, an automatic spatial feature extraction approach based on image raster and segmental vector data cross-analysis is proposed for the classification of very high spatial resolution (VHSR) aerial imagery. First, multi-resolution segmentation is used to generate strongly homogeneous image objects and extract corresponding vectors. Then, to automatically explore the region of a ground target, two rules, which are derived from Tobler’s First Law of Geography (TFL) and a topological relationship of vector data, are integrated to constrain the extension of a region around a central object. Third, the shape and size of the extended region are described. A final classification map is achieved through a supervised classifier using shape, size, and spectral features. Experiments on three real aerial images of VHSR (0.1 to 0.32 m) are done to evaluate effectiveness and robustness of the proposed approach. Comparisons to state-of-the-art methods demonstrate the superiority of the proposed method in VHSR image classification.

This work proposes a hollow-core photonic crystal fiber-based edible oil sensor in the terahertz (THz) range (e.g., 1.0THz ≤ f ≤ 3.0THz) and different sensing characteristics are numerically analyzed. The suggested sensor’s performance was assessed by means of COMSOL Multiphysics, a commercial program that uses the finite element approach. The computational results indicate that the relative sensitivity is 85.591%, 84.648%, 82.625%, 82.683%, and 79.161%, respectively, at f = 2.2 THz, for several types of sunflower oil, mustard oil, coconut oil, olive oil and palm oil; and the corresponding effective areas are 7.22×10-8 um2, 7.09×10-8 um2, 6.83×10-8 um2,7.09×10-8 um2, 6.5231 ×10-8 um2. In addition, the effective material loss for sunflower oil, muster oil, coconut oil, olive oil, and palm oil has been found to be 0.02561 cm-1, 0.027054 cm-1, 0.030322 cm-1, 0.028854 cm-1 ,0.035427cm-1 respectively. Moreover, the proposed sensor also has low confinement loss are 1.55×10-8 dB/m, 1.63×10-8 dB/m, 1.31×10-8 dB/m, 1.99×10-8 dB/m, 4.0345×10-8 dB/m.This proposed sensor can be fabricated using extrusion and 3D-printing technologies, and due to its augmented detecting capabilities, it can be a vital part of oil sensing devices implemented in real life such as industry fields.

In this study, we present comprehensive climatologies of effective ultraviolet (UV) quantities and photosynthetically active radiation (PAR) over Cyprus for the period 2004 to 2023, leveraging the synergy of earth observation (EO) data and radiative transfer model simulations. The EO dataset, encompassing satellite and re-analysis data for aerosols, total ozone column, and water vapor, alongside cloud modification factors, to capture the nuanced dynamics of Cyprus's atmospheric conditions. With a temporal resolution of 15 minutes and a spatial of 0.05°x0.05°, these climatologies undergo rigorous validation against established satellite datasets and are further evaluated through comparisons with ground-based global horizontal irradiance measurements provided by the Meteorological Office of Cyprus. This dual-method validation approach not only underscores the models' accuracy but also highlights their proficiency in capturing intra-daily cloud coverage variations. Our analysis extends to investigating the long-term trends of these solar radiation quantities, examining their interplay with changes in cloud attenuation, aerosol optical depth (AOD), and total ozone column (TOC). Significant decreasing trends in the noon ultraviolet index (UVI), of -2 to -4% per decade have been found in Autumn, especially marked on the island’s Northeastern part, mainly originating from the (significant) positive trends in TOC. The significant decreasing trends in TOC, of -2 to -3% per decade that were found in Spring do not result in correspondingly significant positive trends in the noon UVI since variations in cloudiness and aerosols also have a strong impact on the UVI in this season. The seasonal trends in the Daylight Integral (DLI) were generally not significant. These insights provide a valuable foundation for further studies aimed at developing public health strategies and enhancing agricultural productivity, highlighting the critical importance of accurate and high-resolution climatological data.

The Microwave Humidity and Temperature sounder (MWHTS) on board the Fengyun (FY)-3C satellite measure the outgoing radiance form the Earth surface and atmospheric constituents. MWHTS makes measurements in the isolated oxygen absorption line near 118 GHz and the vicinity of strong water vapor line around 183 GHz, can provide fine vertical distribution structure of both atmospheric humidity and temperature. However, in order to obtain the accurate soundings of humidity and temperature by the physical retrieval method, bias between the observed radiance and those simulated by radiative transfer model from the background or first guess profiles must be correct. In this study, two bias correction methods are developed through the correlation analysis between MWHTS measurements and air mass identified by the first guess profiles of the physical inversion, one is the linear regression correction (LRC) and the other is neural networks correction (NNC), representing the linear and nonlinear nature between MWHTS measurements and air mass, respectively. Both correction methods have been applied to MWHTS observed brightness temperatures over the geographic area (180° W-180° E, 60° S-60° N). The corrected results are evaluated by the probability density function of the difference between corrected observations and simulated values and the root mean square error (RMSE) with respect to simulated observations. The numerical results show that the NNC method perform better, especially in MWHTS channels 1 and 7-9 whose peak weight function heights are close to the surface. In order to assess the effects of bias correction methods proposed in this study on the retrieval accuracy, a one-dimensional variational system was built and applied to the MWHTS uncorrected and corrected brightness temperatures to estimated atmospheric temperature and humidity profiles, The retrieval results show that the NNC has better performance which is to be expected. An indication of the stability and robustness of NNC method is given which suggests that the NNC method has promising application perspectives in the physical retrieval.

This paper presents a new methodology to evaluate the performance of an electric vehicle hybrid power system consisting of a fuel cell and a supercapacitor. The study compares the results with those obtained for a battery-electric vehicle. The methodology extends to three driving modes, ECO, NORMAL, and SPORT, corresponding to conservative, moderate, and aggressive acceleration, and three driving conditions, low, medium, and high energy demand. We develop a simulation process to evaluate the energy consumption and the energy rate of a specific electric vehicle used as a prototype for the study. The methodology applies to a driving route that includes acceleration, deceleration, braking, and constant speed segments reproducing standard driving conditions in urban journeys. The proposed method considers combined driving modes, ECO, NORMAL, and SPORT, in each acceleration process, with variable fractions, 0% to 100%, for each mode. This methodology optimizes the simulation results as it fits the current driving way in urban environments. The simulation results show an average reduction in energy consumption of 37% and 27.1% in vehicle weight, contributing to lower energy use. The study concludes that using a hybrid power system, fuel cell/supercapacitor, instead of a battery in electric vehicles is beneficial, especially in journeys with frequent acceleration processes.

There are many uncertainties and risks in residential electricity consumption during the economic development. Knowledge of the relationship between residential electricity consumption and its key determinant—income—are important to the sustainable development of electric power industry. Using panel data from 30 provinces for the 1995-2012 period, this study investigates how residential electricity consumption changes as incomes increase in China. Previous studies typically used linear or quadratic double-logarithmic models imposing ex ante restrictions on the indistinct relationship between residential electricity consumption and income. Contrary to those models, we employed a reduced piecewise linear model that is self-adaptive and highly flexible and circumvents the problem of “prior restrictions.” Robust tests of different segment specifications and regression methods are performed to ensure the conservatism of the research. The results provide strong evidence that the income elasticity was approximately one, and it remained stable throughout the estimation period. The income threshold at which residential electricity consumption automatically remains stable or slows has not been reached. To ensure the sustainable development of the electric power industry, introducing higher energy efficiency standards for electrical appliances and improving income levels are vital. And government should emphasize electricity conservation in industrial sector rather than in residential sector.

Floods are among the most serious natural disasters worldwide; they cause enormous crop losses every year and threaten world food security. There are many studies focused on flood impact assessments for administrative districts but fewer on postdisaster impact assessments for specific crops. Therefore, this study used remote sensing data, including the normalized difference vegetation index (NDVI), elevation data, slope data, and rainfall data, combined with crop growing season data to construct a crop flood damage assessment index (CFAI). First, an analytic hierarchy process (AHP) was used to assign weights to the impact factors; then, the weighted composite score method was used to calculate the CFAI; and finally, the impact was classified as slight, moderate, or severe based on the magnitude of the CFAI . This method was used for the Missouri River floods of 2019 in the U.S. Due to the lack of measured data, the disaster vegetation damage index (DVDI) was used to validate the results. The combined approach achieved a high degree of consistency in spatial distribution. The CFAI can respond well to the degree of crop impact after flooding, providing new ideas and reference standards for agriculture-related departments.

The state detection of power cable is very important to ensure the reliability of power supply. Traditional sensors are mostly based on electric field detection, the operation is complex, and its efficiency needs to be improved. This paper optimizes the design and development of the magnetic field detection sensor for AC power cables. Firstly, through the establishment of the magnetic field sensor model, it is determined that permalloy is the material of the magnetic core, the optimal aspect ratio of the magnetic core is 20, and the ratio of coil length to core length is 0.3. Secondly, the coil simulation model is established, and it is determined that the optimal number of turns of the coil is 11000 turns, the diameter of the enamelled copper wire is 0.08mm, and the equivalent magnetic field noise of the sensor is 0.06pT. Finally, the amplifying circuit based on negative magnetic flux feedback is designed and the sensor is assembled, and the experimental circuit is built for sensitivity test. the results show that the sensitivity of the magnetic field sensor is 327.6mV/μT. The sensor designed in this paper has the advantages of small size, high sensitivity, easy to carry and high reliability.

In order to improve contrast and restore color for underwater image captured by camera sensors without suffering from insufficient details and color cast, a fusion algorithm for image enhancement in different color spaces based on contrast limited adaptive histogram equalization (CLAHE) is proposed in this article. The original color image is first converted from RGB color space to two different special color spaces: YIQ and HSI. The color space conversion from RGB to YIQ is a linear transformation, while the RGB to HSI conversion is nonlinear. Then, the algorithm separately operates CLAHE in YIQ and HSI color spaces to obtain two different enhancement images. The luminance component (Y) in the YIQ color space and the intensity component (I) in the HSI color space are enhanced with CLAHE algorithm. The CLAHE has two key parameters: Block Size and Clip Limit, which mainly control the quality of CLAHE enhancement image. After that, the YIQ and HSI enhancement images are respectively converted backward to RGB color. When the three components of red, green, and blue are not coherent in the YIQ-RGB or HSI-RGB images, the three components will have to be harmonized with the CLAHE algorithm in RGB space. Finally, with 4 direction Sobel edge detector in the bounded general logarithm ratio operation, a self-adaptive weight selection nonlinear image enhancement is carried out to fuse YIQ-RGB and HSI-RGB images together to achieve the final fused image. The enhancement fusion algorithm has two key factors: average of Sobel edge detector and fusion coefficient, and these two factors determine the effects of enhancement fusion algorithm. A series of evaluate metrics such as mean, contrast, entropy, colorfulness metric (CM), mean square error (MSE) and peak signal to noise ratio (PSNR) are used to assess the proposed enhancement algorithm. The experiments results showed that the proposed algorithm provides more detail enhancement and higher values of colorfulness restoration as compared to other existing image enhancement algorithms. The proposed algorithm can suppress effectively noise interference, improve the image quality for underwater image availably.

A new type of artificial block is proposed by modifying the traditional block. Based on the physical model experiment, the wave reflection and run-up characteristics of the new ecological blocks under regular waves were examined, and the influence of the height of the "planting trough" border on the hydrodynamic properties was analyzed. The results indicate that the wave reflection and run-up would decrease with a decrease in the breakwater slope. As wave height increases, wave run-up increases, and the reflection coefficient falls. Wave reflection and run-up increase with an increasing wave period. The relative depth of the water has a smaller impact on the wave reflection than the wave run-up. The reflection coefficient of the new ecological blocks is consistently lower than that of the conventional and continues to decrease as the border of the "planting trough" is raised. The raised borders prevent water loss in the trough, resulting in no significant improvement in the wave run-up performance of the new blocks. The reflection coefficient and the relative run-up R/H gradually increase with the average wave breaking parameter ξ increase. The crude permeability coefficients for the new blocks, New Heights 1 and New Heights 2, are 0.53, 0.53, and 0.54, respectively.

Numerous elements, such as the composition and characteristics of carbon nanomaterials, the composition and characteristics of the matrix material, moisture levels, temperature, and loading circumstances, influence the piezoresistive behaviour of self-sensing cementitious composites. While some past research has explored the impact of some of these factors on the performance of self-sensing cementitious composites, additional investigations need to be conducted to delve into how loading conditions affect the sensitivity of self-sensing cement-stabilized composites. Therefore, this study explores the influences of various loading conditions (i.e., location of loading regarding the location of recording electrodes, and loading level) on the electromechanical performance of self-sensing cement-stabilized sand. To this end, firstly, the evaluation of the percolation threshold based on 10% cement-stabilized sand specimens containing various multiwall carbon nanotubes (MWCNTs) and graphene nanoplatelets (GNPs) was performed. Then, 10% cement-stabilized sand containing 4% MWCNTs/GNPs was tested under various cyclic compressive stresses. The results suggested that the distance between the loading area and the electrode location used for recording the electrical resistance significantly impacts the sensitivity of cement-stabilized sand. Optimal sensitivity was achieved when the electrodes were positioned directly beneath the loading area. Moreover, the study yielded that the stress sensitivity of self-sensing cement-stabilized sand increases proportionally with the stress level. Examination through scanning electron microscopy (SEM) demonstrated that the loading condition influences the bridging characteristics of carbon nanomaterials in cement-stabilized sand, leading to diverse electromechanical behaviors based on the loading condition. This study underscores the importance of considering specific parameters when designing the application of self-sensing cement-stabilized sand for practical field use.

Optimizing the NACA0015 airfoil which is widely applied in small-scale vertical axis wind turbine to make it has a better aerodynamic performance. In the optimization process, using CST parameterization method to perturb the airfoil geometry, the thickness and camber of the airfoil are selected as the constraint, and the value of the maximum tangential force coefficient is chosen as the objective function, the genetic algorithm based on non-dominated sorting (NSGA-II)is selected as an optimization method, calculates the aerodynamic performance of the airfoil by applying the approach of combining XFOIL program and Viterna-Corrigan post-stall mode ,and establishes the optimizing process by the optimization software modefrontier for NACA0015 airfoil’s muti-point optimization, validate the airfoil’s performance with CFD finally. The result illustrates that, by comparing with the NACA0015 airfoil, the optimized airfoil’s lift to drag ratio is improved over a wide range of attack angles, the stall performance is more gentle. The maximum lift coefficient, the maximum lift-drag ratio and the maximum tangential force coefficient are increased by 7.5%,9 and 8.87%, respectively. The optimized airfoil has a wide variable condition performance, more suitable for the operating conditions of a vertical axis wind turbine. Finally, predict the rotor efficiency with optimized airfoil and NACA0015 airfoil for different tip speed ratios and different solidities with multiple streamtube model, the result shows the rotor with optimized airfoil has a higher efficiency.

Single-phase-to-ground fault in non-effectively grounded systems poses serious public safety concern. Along with increasing deployment of low-voltage (LV) sensors, new opportunities and ways are created for solving this traditional problem in distribution systems. A new approach, identifying primary single-phase-to-ground line fault and locating it through measurement data from smart sensors deployed in the secondary side of distribution transformers, is proposed in this paper. When a fault occurs in primary distribution feeder, the transient aerial mode voltage (AMV) of each LV smart sensor is calculated. The fault line can be identified by an abrupt change value of AMV at LV side. Next, by finding the position of the maximum value of this AMV from LV sensors on the fault line, the fault location can be pinpointed to two neighboring distribution transformers. The proposed method has been proven to be efficient and reliable by simulation studies.

Fiber distributed optical fiber acoustic sensor (DAS) is generally used in distributed long-distance acoustic/vibration measurement. We found that DAS with excellent performance of low self-noise and anti-fading in combination with the plastic structure in daily life as an acoustic transducer can achieve high-sensitivity acoustic measurement at a single point rather than designing a state-of-the-art acoustic transducer or using special enhanced scattering fiber. The simple acoustic transducer we proposed for DAS can reach the sensitivity level of -106.5dB re. 1rad/μPa at a sensing range of 5.1 km, which can meet many demands on the industrial site.

Volcanic activity essentially consists of the transfer of heat from the Earth’ interior to the surface. The precise signature of this heat transfer relates directly to the processes underway at and within a particular volcano and this can be observed, at a safe distance, remotely, using infrared sensors that are present on Earth-orbiting satellites. For over 50 years, scientists have perfected this art using sensors intended for other purposes, and they are now in a position to determine the particular sort of activity that characterizes different volcanoes. This review will describe the theoretical basis of the discipline and then discuss the sensors available for the task and the history of their use. Challenges and opportunities for future development in the discipline are then discussed.

Rapid and accurate detection of road cracks is of great significance for road health monitoring, but currently this work is mainly completed through manual site surveys. Low-altitude UAV remote sensing can obtain images with centimeter or even subcentimeter ground resolution, which provides a new efficient and economical approach for rapid crack detection. Nevertheless, crack detection networks face challenges such as edge blurring and misidentification due to the heterogeneity of road cracks and the complexity of the background. To address these issues, we propose a real-time edge reconstruction crack detection network (ERNet) which adopts multi-level information aggregation to reconstruct crack edges and improve the accuracy of segmentation between the target and background. To capture global dependencies across spatial and channel levels, we propose an efficient bilateral decomposed convolutional attention module (BDAM) that combines depth separable convolution and dilated convolution to capture global dependencies across spatial and channel levels. To enhance the accuracy of crack detection, we use a coordinate-based fusion module that integrates spatial, semantic, and edge reconstruction information. In addition, we propose an automatic measurement of crack information for extracting the crack trunk and its corresponding length and width. Experimental results demonstrate that our network achieves the best balance between accuracy and inference speed.

Statistical denoising techniques have been well studied, however many challenges still remain. This 9 article focuses on determining the least necessary number of significant samples in a statistical pop-10 ulation sampling, while minimizing the impact on the statistical detection of the fiber Bragg grating 11 (FBG) power spectra. This is achieved by using Bayesian decision making, small population statis-12 tics while excluding false detection. First, we investigate the impact of two-sided sliding window 13 technique applied near the cell under the test. The window size varies from 8 to 60 samples. The 14 considered maximum size of population sampling is connected with the number of wavelength 15 samples within the bandwidth of the symmetrical FBG power spectra peaks. Regarding the sym-16 metry of FBG power spectra peaks and the possible reduction of computational demands, we inves-17 tigate the impact of a one-sided sliding window. This enables to achieve less processing latency for 18 real time applications thus brings benefits to FBG-based fiber optical sensing. Both, two- and one-19 sided small population sampling techniques are then experimentally verified. Detection results are 20 analyzed in depth via calculating detection thresholds by using the small size window sliding along-21 side the waveband. From results achieved, it was found that the normality three-sigma rule does 22 not need to be followed while using the small population sampling. Experimental demonstrations 23 and analyses showed that the proposed concept of denoising and statistical threshold detection 24 based on the sliding window does not depend on the prior knowledge of probability distribution 25 functions of the FBG power spectra peaks level and background noise. We have also found that the 26 thresholds’ adaptability mainly depends on the statistical numerical characteristics of the above ad-27 ditive mixture of the FBG power spectra peaks signals and background noise.

The main aim of this work is to present a step-by-step procedure to model and analyze the power loss distribution of three-level Gallium Nitride (GaN) inverters. It has been applied to three distinct three-phase three-levels voltage source inverters utilized in electric traction drives: Active Neutral Point Clamped, Neutral Point Clamped and T-Type Neutral Point Clamped. The proposed analytical power loss modelling, combined to an equivalent representation of the electrical machine demonstrated to be a viable solution to achieve a time-saving and low computational burden simulation platform, leading to satisfying accuracy results. This has been confirmed by comparing the results carried out from the simulations of a 110kW permanent magnet synchronous motor drive and those determined by considering a simplified circuital representation based on the proposed analytical power loss modelling.

The effects of rare earth Ce on the microstructure and properties of cast pure copper were investigated through thermodynamic calculations, XRD analysis, mechanical testing, metallographic microscopy, and scanning electron microscopy (SEM). The experimental results demonstrate that the reaction between rare earth Ce and oxygen as well as sulfur in copper exhibits a significantly negative Gibbs free energy value, indicating a strong thermodynamic driving force for deoxidation and desulfurization reactions. Ce is capable of removing trace amounts of O and S from copper. Moreover, the maximum solid solubility of Ce in Cu falls within the range of 0.009% to 0.01%. Furthermore, Ce can refine columnar grains while enlarging equiaxed grains in as-cast copper.Upon addition of rare earth Ce, the tensile strength increased by 8.45%, elongation increased by 12.1%, and microhardness rose from 73.5HV to 81.2HV-an increase of 10.5%. Overall, rare earth Ce has been found to enhance both the microstructure and mechanical properties of cast pure copper.

Natural polluted insulator surfaces are always coated with various kinds of soluble constituents, and those constituents affect flashover performance differentially. Currently this fact is not considered either in laboratory experiments or field pollution degree measurements, causing the existing insulation selection method to be deficient. In this paper a systematical research on insulator flashover voltage gradient correction involving types of soluble pollution constituents was presented. Taking typical type glass insulator as the sample, its flashover tests polluted by typical soluble chemicals NaCl, NaNO₃, KNO₃, NH₄NO₃, MgSO₄, Ca(NO₃)₂ and CaSO₄ were carried out. Then the flashover gradient correction was made combining the flashover performance of each soluble constituent, the ESDD contribution of the seven constituents, as well as the saturation performance of CaSO₄. The correction was well verified with the flashover test results of insulator polluted by three types of soluble mixture. Research results indicate that the flashover gradient correction method proposed by this paper performs well in reducing the calculating error. It is recommended to carry out component measurements and flashover gradient correction to better select outdoor insulation configuration.

Detecting and monitoring changes in soil salinity through remote sensing provides an opportunity for field assessment in regions where on-site measurements are limited. This investigation, carried out in Siwa Oasis, Egypt, aimed to assess the efficacy of several soil salinity indices derived from Landsat 5 and 7 satellite images. To achieve this, 56 on-site ground measurements were utilized for evaluation purposes. The study aimed to improve the correlation between EC and index values and explore the relationship between salinity and changes in land cover. Eleven spectral indices were calculated for nine scenes captured in different months from August to December. The first approach involved stacking the data to identify the index with the strongest correlation with ground EC values, without the need for complex analysis or EC value ranging. In the second approach, the ground EC measurements were classified into seven different salinity categories, and the correlation coefficient was calculated between each index and each salinity category. The third approach analyzed the data temporally, considering different salinity levels. Lastly, a spatial correlation analysis was conducted between EC and index values in the fourth scenario. The initial approach revealed a weak correlation due to substantial variation in EC values. However, the SI index demonstrated the highest correlation coefficient of 0.38. In the second scenario, the S2 index exhibited the highest correlation of 0.96 for moderate salinity samples. The third scenario showed that the S1 index achieved the highest correlation value of 0.99 for moderately saline areas. In the fourth scenario, the SI index exhibited the strongest correlation among all four ponds with correlation coefficients of 0.23, 0.23, 0.18, and 0.61. Notably, the correlations observed in the second and third scenarios demonstrated higher correlation coefficients compared to both the first and fourth scenarios. The study highlighted significant variations in EC levels related to land cover types and pond elevation. Additionally, remote sensing methods detected a 48% increase in total vegetated area over 17 years, showing the potential of remote sensing techniques in salinity monitoring for expanding agriculture and improving land management.

Addressing the pressing challenge of global warming, reducing greenhouse gas emissions in the transportation sector is a critical imperative. Battery and fuel-cell electric vehicles have emerged as promising solutions for curbing emissions in this sector. In this study, we conducted a comprehensive life cycle assessment (LCA) for typical passenger vehicles, heavy duty trucks and city buses using either proton-exchange membrane fuel cells or Li-ion batteries with different cell chemistries. To ensure accuracy, we supplemented existing studies with data from the literature, particularly for the recycling phase, as database limitations were encountered. Our results highlight that fuel cell and battery systems exhibit large emissions in the production phase. Recycling can significantly offset some of these emissions, but a comparison of the technologies examined revealed considerable differences. Overall, battery electric vehicles consistently outperform fuel cell electric vehicles regarding absolute greenhouse gas emissions. Hence, we recommend prioritizing battery electric over fuel cell vehicles. However, deploying fuel cell electric vehicles could become attractive in a hydrogen economy scenario where other factors, e. g. the conversion and storage of surplus renewable electricity via electrolysis, become important.

Gas and power networks are tightly coupled and interact with each other due to physically interconnected facilities. In an integrated gas and power network, a contingency observed in one system may cause iterative cascading failures, resulting in network wide disruptions. Therefore, understanding the impacts of the interactions in both systems is crucial for governments, system operators, regulators and operational planners, particularly, to ensure security of supply for the overall energy system. Although simulation has been widely used in the assessment of gas systems as well as power systems, there is a significant gap in simulation models that are able to address the coupling of both systems. In this paper, a simulation framework that models and simulates the gas and power network in an integrated manner is proposed. The framework consist of a transient model for the gas system and a steady state model for the power system based on AC-Optimal Power Flow. The gas and power system model are coupled through an interface which uses the coupling equations to establish the data exchange and coordination between the individual models. The bidirectional interlink between both systems considered in this studies are the fuel gas offtake of gas fired power plants for power generation and the power supply to LNG terminals and electric drivers installed in gas compressor stations and underground gas storage facilities. The simulation framework is implemented into an innovative simulation tool named SAInt (Scenario Analysis Interface for Energy Systems) and the capabilities of the tool are demonstrated by performing a contingency analysis for a real world example. Results indicate how a disruption triggered in one system propagates to the other system and affects the operation of critical facilities. In addition, the studies show the importance of using transient gas models for security of supply studies instead of successions of steady state models, where the time evolution of the line pack is not captured correctly.

(1) Background: The aim of the research was to present and emphasize the importance of magnetic resonance imaging (MRI) in diagnosing Achilles tendon (AT) ruptures by presenting case reports. (2) Materials and Methods: The sample of respondents included 7 patients (4 males and 3 females, 2 athletes and 5 non-athletes), aged 25 to 58 years, with AT injuries, who were examined and treated at the Institute for Treatment and Rehabilitation "Niška Banja", Niš, Serbia. Ankle examinations with MRI were conducted using the Esaote O-scan 0.3 T machine. The examinations were performed without the application of a paramagnetic contrast agent and without the use of anesthesia. Results: The MRI method's sensitivity and overall diagnostic accuracy were excellent, with 100% true positives. In our study, the method accurately detected the presence, location, and severity of AT injuries in all cases. MRI is an important and reliable method for detecting AT injuries, classifying them, monitoring the course of recovery, and assessing the effects of therapy. Conclusions: An unrecognized or delayed diagnosis of an AT injury can lead to chronic changes. Timely diagnosis (clinical examination, ultrasonography, magnetic resonance imaging) and appropriate treatment (conservative or operative) enable patients to return to normal activities, including sports. Unfortunately, the use of MRI is limited by restricted access and the cost of the examination.

Deep Learning is an extremely important research topic in Earth Observation. Current use-cases range from semantic image segmentation, object detection to more common problems found in computer vision such as object identification. Earth Observation is an excellent source for different types of problems and data for Machine Learning in general and Deep Learning in particular. It can be argued that both Earth Observation and Deep Learning as fields of research will benefit greatly from this recent trend of research. In this paper we take several state of the art Deep Learning network topologies and provide a detailed analysis of their performance for semantic image segmentation for building footprint detection. The dataset used is comprised of high resolution images depicting urban scenes. We focused on single model performance on simple RGB images. In most situations several methods have been applied to increase the accuracy of prediction when using deep learning such as ensembling, alternating between optimisers during training and using pretrained weights to bootstrap new models. These methods although effective, are not indicative of single model performance. Instead, in this paper, we present different topology variations of these state of the art topologies and study how these variations effect both training convergence and out of sample, single model, performance.

The one-dimensional MoS₂/carbon nanofibers (1D MoS₂/CNFs) are synthesized by electrospinning using exfoliated MoS₂ nanosheets and polyacrylonitrile as raw materials. The exfoliated MoS₂ nanosheets with size of about 150 nm are encapsulated in carbon nanofibers, and the free-standing MoS₂/CNFs can be easily cut into flexible tablet and directly used as binder-free anode for lithium storage. The resultant 1D MoS₂/CNFs exhibit a very high reversible capacity of 700 mAh g^-1 at 100 mA g^-1 after 50 cycles, high rate capacity (450 mAh g^-1 at 1000 mA g^-1 after 200 cycles) and good cycle stability.

Ecosystem physical structure, defined by the quantity and spatial distribution of biomass, influences a range of ecosystem functions. Remote sensing tools permit the non-destructive characterization of canopy and root features, potentially providing opportunities to link above- and belowground structure at fine spatial resolution in functionally meaningful ways. To test this possibility, we employed ground-based portable canopy lidar (PCL) and ground penetrating radar (GPR) along co-located transects in forested sites spanning multiple stages of ecosystem development and, consequently, of structural complexity. We examined canopy and root structural data for coherence at multiple spatial scales ≤ 10 m within each site using wavelet analysis. Forest sites varied substantially in vertical canopy and root structure, with leaf area index and root mass more evenly distributed by height and depth, respectively, as forests aged. In all sites, above- and belowground structure, characterized as mean maximum canopy height and root mass, exhibited significant coherence at a scale of 3.5-4 meters, and results suggest that the scale of coherence may increase with stand age. Our findings demonstrate that canopy and root structure are linked at characteristic spatial scales, which provides the basis to optimize scales of observation. Our study highlights the potential, and limitations, for fusing lidar and radar technologies to quantitatively couple above- and belowground ecosystem structure.

In this paper, an adaptive proportional and integral (PI) controller for speed control of electric drives is developed. The adaptive PI controller is designed based on model reference adaptive identification and the Lyapunov function so that the system stability can be proved. To identify the inertia, the viscous friction torque coefficient, and the load torque simultaneously and smoothly, sinusoidal speed reference is usually employed. A modified motion equation considering the low-pass filter for feedback speed and the Coulomb friction torque is introduced and the relationship between the identified parameters and their actual values are clarified. A high-precision digital simulation model is built based on MATLAB/Simulink. The effectiveness of the proposed method is verified by simulations under various conditions.

Although, promotion of urbanization culture in recent decades has made inevitable development of cities in the world, however, the development can be guided in a direction that leave, to the extent possible, minimum socioeconomic and environmental impacts. For this, it is required to first forecast auto-spreading orientation of cities and suburbs in rural areas over time and then avoid shapeless growth of cities. This paper is an attempt to develop a dynamic hybrid model based on logistic regression (LR), Markov chain (MC), and cellular automata (CA) for prediction of future urban sprawl in fast-growing cities. The model was developed using 12 widely-used urban development criteria, whose significant coefficient was determined by logistic regression, and validated by relative operating characteristic (ROC) analysis. The validated model was run in Guilan, a tourist province in northern Iran with a very high rate of urban development. For this, changes in the area of urban land use were detected over the period of 1989 to 2013 and then, future sprawl of the province was forecasted by the years 2025 and 2037. The analysis results revealed that the area of urban land use was increased by more than 1.7 % from 36012.5 ha in 1989 to 59754.8 ha in 2013, and the area of Caspian Hyrcanian forestland was reduced by 31628 ha. The results also predicted an alarming increase in the rate of urban development in the province by the years 2025 and 2037, during which urban land use is predicted to develop 0.9 % and 1.38 %, respectively. The development pattern is expected to be uneven and scattered, without following any particular direction. The development will occur close to the existing or newly-formed urban basements as well as around major roads and commercial areas. This development, if not controlled, will lead to the loss of 13863 ha of Hyrcanian forests and if the trend continues, 21013 ha of Hyrcanian forests and 20208 ha of Barren/open lands are expected to be destroyed by the year 2037. In general, the proposed model is an efficient tool for the support of urban planning decisions and facilitates the process of sustainable development of cities by providing decision-makers with an overview on future development of cities where the growth rate is very fast.

The strong competition in the automotive industry has required manufacturers to implement lean production, both with methods and techniques specific to Industry 4.0. At the same time, universities must provide graduates with specific skills for applying these new production methods and techniques. In this context, a Lean Learning Factory was developed in the Pitesti University Center, which allows students to learn, experiment, and research, in an environment similar to that of enterprises, the new Lean Manufacturing methods and techniques, and Industry 4.0. The research presented in this study had as its objective identifying the minimum number of repetitions necessary to train operators who serve two differently organized workstations, one classic, the other including digital techniques, but on which the same assembly operation is performed. Several indicators were considered in the analysis, such as the number of errors, the number of stops, the effective duration of the work cycle, and the percentage ratio between the standard duration of cyclical activities and the effective duration of the work cycle. The evolution of these indicators was mathematically modelled by regression functions, using the least squares method. The obtained results also highlight the usefulness of applying the DOJO method as a Lean manufacturing-specific learning technique and the efficiency of implementing digital techniques in work organization.

The link between the world of communication and the world of racing is provided by telemetry systems in electric racing cars. These systems send real-time data about the vehicle’s behavior and systems to enable informed decisions during the race. The aim of this research was to integrate telemetry into the battery bank of a racing electric vehicle to find the optimal values of current and voltage that optimize the charging process, thus improving the vehicle’s performance in competition using Response Surface Analysis. Particularly, the telemetry system consisted of an Arduino Mega, a digital wattmeter, and temperature sensors, all installed in the vehicle. Once the telemetry data was obtained, a response surface design was adapted with current, voltage, and temperature as factors, varying from low to high values, with the objective function being to minimize the battery’s charging time. Applying the response surface methodology and the steepest descent algorithm, it was found that all factors significantly affect the charging time, with the minimum charge time being 6961 seconds, obtained with a current of 2.4 amps and voltages of 50.5 volts and 43.6 volts.

Recently many researches of EOS (Electric Arc Furnace Oxidizing Slag) on application to construction industry have been carried out with increasing its production and limited reclamation site. EOS can be used as a fine aggregate for construction material, however, its engineering properties vary with the manufacturing process and producing district, causing a quality differences in material performance. In the work, EOS is obtained from steel manufacturing plants in South Korea and the engineering properties are evaluated for EOS and the cement mortar with EOS, respectively. From the tests, EOS is mainly made up of CaO, SiO₂, and FeO with 18.2% of larnite which has a crystal structure of β-C₂S with similar cement mineral. EOS mortar shows an increasing compressive strength with more EOS content, which is affected by a considerable amount of larnite (β-C2S) in EOS. The EOS based mortar with ERS (Electric Arc Furnace Reduction Slag) shows unsatisfactory results over the criteria for rate of change, which implies that more consideration must be taken for the usage of the mixed ERS and EOS for cement mortar due to swelling effect of ERS on dimensional stability.

This work presents the design, construction and performance evaluation of a photovoltaic greenhouse as an energy hub (EH) in modern agriculture that integrates battery energy storage (BES) and an electric vehicle charging station (EV). The greenhouse is composed of 48 semi-transparent PV panels with nominal transparency of 20% and 110 W capacity. The control of the PV greenhouse as EH was approached as an optimization problem with the aim of minimizing the cost of the energy used from the grid. Simulation results indicate that the integrated BES is capable of balancing power transactions within the microgrid. In addition, it was found that the case of slow charging of the EV at night was less demanding on the BES than fast charging during the day in terms of abrupt power transitions and average depletion of BES SOC (61% vs 53%). Empirical results also demonstrated the negative impact of dust generated by agricultural activity on the performance of solar panels. For a period analyzed of three years, an average yearly production loss of 6.8% was calculated.

This study introduces a Fiber Specklegram Sensor (FSS) design for temperature measurement utilizing a single-multi-single mode optical fiber configuration. FSS technology offers unique advantages for potential development into portable sensing systems. This investigation explores an FSS design compatible with miniaturization by optimizing the interrogation system based on the relationship between speckle grain size and filtering fiber area. Temperature variations are detected through fluctuations in optical power at the sensor output, offering a simple and reduced interrogation scheme. The performance of the FSS is assessed through post-calibration measurements compared to a commercial Fiber Bragg Grating (FBG) sensor, demonstrating comparable results. These findings pave the way for compact and portable fiber optic temperature sensing systems leveraging FSS advantages while maintaining compatibility with established fiber optic measurements.

Recently, the phase-sensitive OTDR (Φ-OTDR) based vibration sensor system has gained the focus of many researchers and some efforts have been undertaken to push further the limitations imposed on the performance of the Φ-OTDR sensor system. Then, progress in the different areas of its performance evaluation factors such as: improvement of the signal-to-noise ratio (SNR), spatial resolution (SR) in the sub-meter range, enlargement of the sensing range, frequency response bandwidth over the conventional limit and phase signal demodulation for quantitative measurement have been realized. This paper presents an overview of the recent progress in the Φ-OTDR based vibration sensing system in the different areas mentioned above.

In the field of embedded systems, energy efficiency is a critical requirement, particularly for battery-powered devices. RISC-V processors have gained popularity due to their flexibility and open-source nature, making them an attractive choice for embedded applications. However, not all RISC-V processors are equally energy-efficient, and it is important to evaluate their performance in specific use cases. This paper evaluates the energy consumption and resource utilization of a new RISC-V processor, RisCO2, and four existing processors - Zero-riscy, Micro-riscy, Ri5cy, and CV32E40P - in a signal demodulation application for NDIR CO2 sensors. The processors were implemented in the PULPino SoC and synthesized using Vivado IDE. The processor named RisCO2 is based on the RV32E_Zfinx instruction set and was designed from scratch by the authors specifically for low-power signal processing applications such as signal demodulation in CO2 NDIR sensors. The other processors are Ri5cy, Micro-riscy, and Zero-riscy, developed by the PULP Platform team, and CV32E40P (derived from Ri5cy) from the OpenHW Group, all of them widely used in the RISC-V community. Our experiments showed that RisCO2 had the lowest energy consumption among the five processors, with a 53.5% reduction in energy consumption compared to CV32E40P and a 94.8% reduction compared to Micro-riscy. Additionally, RisCO2 had the lowest FPGA resource utilization compared to the best-performing processors, CV32E40P and Ri5cy, with a 46.1% and a 59% reduction in LUTs, respectively. Our findings suggest that RisCO2 is a highly energy-efficient RISC-V processor for NDIR CO2 sensors that require signal demodulation. The results also highlight the importance of evaluating processors in specific use cases to identify the most energy-efficient option. This paper provides valuable insights for designers of energy-efficient embedded systems using RISC-V processors.

We report the relative humidity (R.H.) sensing response of a resistive sensor, employing sensing layers based on a ternary nanohybrid comprising holey carbon nanohorns (CNHox), potassium chloride (KCl), and polyvinylpyrrolidone (PVP) at mass ratios 7/1/2, 6.5/1.5/2, and 6/2/2 (w/w/w/w). The sensing structure comprises a silicon substrate, a SiO2 layer, and interdigitated transducer (IDT) electrodes. The sensing film is deposited on the sensing structure via the drop-casting method. The sensing layers' morphology and composition are investigated through Scanning Electron Microscopy (S.E.M.) and RAMAN spectroscopy. The ternary hybrid-based thin film resistance increases when the sensors are exposed to R.H., ranging from 0% to 100%. The manufactured devices show a room temperature response comparable to a commercial capacitive R.H. sensor and are characterized by excellent linearity, rapid response time, and good sensitivity. The presented sensors exhibit superior performance in terms of sensitivity compared to other similarly manufactured and tested sensors that employ a CNHox-based sensing layer. We explain the sensing role of each constituent of the ternary hybrid nanocomposites based on their chemical and physical properties, electronic properties, and affinity for water molecules. Different alternative sensing mechanisms are considered and discussed, such as the decreasing number of holes in the holey CNHox at the interaction with water molecules, proton conduction, and PVP swelling.

Iron is an essential nutrient and necessary for biological functions from DNA replication and repair to transcriptional regulation, mitochondrial respiration, electron transfer, oxygen transport, photosynthesis, enzymatic catalysis, and nitrogen fixation. However, due to iron’s propensity to generate toxic radicals which can cause damage to DNA, proteins, and lipids, multiple processes regulate uptake and distribution of iron in living systems. Understanding how intracellular iron metabolism is optimized and how iron is utilized to regulate other intracellular processes is important to our overall understanding of a multitude of biological processes. One of the tools that the cell utilizes to regulate a multitude of functions is ligation of the iron-sulfur (Fe-S) cluster cofactor. Fe-S clusters comprised of iron and inorganic sulfur are ancient components of living matter on earth that are integral for physiological function in all domains of life. Here we will explore the ways in which the cell utilizes Fe-S clusters to sense the intracellular environment and respond to maintain equilibrium.

The radar sensor described realizes healthcare monitoring capable of detecting subject chest-wall movement caused by cardiopulmonary activities, and wirelessly estimating the respiration and heartbeat rates of the subject without attaching any devices to the body. Conventional single-tone Doppler radar can only capture Doppler signatures because of a lack of bandwidth information with noncontact sensors. In contrast, we take full advantage of impulse radio ultra-wideband (IR-UWB) radar to achieve low power consumption and convenient portability, with a flexible detection range and desirable accuracy. A noise reduction method based on improved ensemble empirical mode decomposition (EEMD) and a vital sign separation method based on the continuous-wavelet transform (CWT) are proposed jointly to improve the signal-to-noise ratio (SNR) in order to acquire accurate respiration and heartbeat rates. Experimental results illustrate that respiration and heartbeat signals can be extracted accurately under different conditions. This noncontact healthcare sensor system proves the commercial feasibility and considerable accessibility of using compact IR-UWB radar for emerging biomedical applications.

Due to the rapid development of unmanned aerial vehicles (UAVs) communication technology, UAVs are gradually competing with primary users (PUs) for spectrum resources. Cognitive radio (CR) is a promising solution to meet the needs. Cooperative spectrum sensing (CSS) is considered as an effective method to detect the PU signal and identify available spectrum resources for UAVs in a cognitive UAV network (CUAVN). However, the cooperative mode among multiple UAVs may incur a high overhead, resulting in performance degradation. Therefore, we introduce a differential sequential 1 (DS1), which incorporates a differential mechanism and leverages the sequential idea based on the classical voting rule to enhance cooperative performance and efficiency. In view of this, we formulate three scenarios to characterize the PU activity and introduce a multi-slot cooperative mode within a single UAV to realize cooperative gain. Further, only the information change about the PU status is sequentially calculated in DS1, and combined with a sequential idea, the efficiency of the voting rule is greatly improved. Moreover, the application of support vector machines (SVM) in dynamic selection enables the selection of the most suitable voting rule based on diverse sensing parameters. This dynamic selection process ensures optimal performance and efficiency by adapting the voting rule to the specific characteristics of the given scenario. Finally, simulation results demonstrate that the superiority of our proposal with respect to the detection performance, sample size and the energy efficiency is evident, which proves the high performance of the proposed policy.

This work simulates the performance of lithium batteries for electric vehicles under different charge and discharge rates. The simulation is based on similarity factors for power, voltage and current, reproducing the real operation conditions of an electric vehicle at the model scale. Most current driving modes have been analysed corresponding to discharge rates from 0.1C to 0.37C. The simulation has also been applied to determine charging time using charge power in real conditions, from 6.1 kW to 18.3 kW (0.1 C to 0.3C). Driving conditions are obtained using equations for vehicle motion including all forces. Tests have been run under two configurations, continuous and alternate current circuits, to reproduce the two types of engines that electric vehicles use. The simulation shows very good agreement in charge and discharge processes, average deviation of 3% related to real conditions, and 1.6% between them, which proves the validity of the simulation process.

Precision agriculture is a farm management technology that involves sensing and then responding to the observed variability in the field. Remote sensing is one of the tools of precision agriculture. The emergence of small unmanned aerial vehicles (sUAV) have paved the way to accessible remote sensing tools for farmers. This paper describes the comparison of two popular off-the-shelf sUAVs: 3DR Iris and DJI Phantom 2. Both units are equipped with a camera gimbal attached with a GoPro camera. The comparison of the two sUAV involves a hovering test and a rectilinear motion test. In the hovering test, the sUAV was allowed to hover over a known object and images were taken every second for two minutes. The position of the object in the images was measured and this was used to assess the stability of the sUAV while hovering. In the rectilinear test, the sUAV was allowed to follow a straight path and images of a lined track were acquired. The lines on the images were then measured on how accurate the sUAV followed the path. Results showed that both sUAV performed well in both the hovering test and the rectilinear motion test. This demonstrates that both sUAVs can be used for agricultural monitoring.

Cannabidiol (CBD) is an active diterpenoid compound that is extracted from the leaves and stem of Cannabis sativa. Previous studies show that CBD is a non-psychotropic compound with significant anti-cancer effects. This study determines its cytotoxic effect on oral cancer cells and OECM1 cells and compares the outcomes with a chemotherapeutic drug, cisplatin. This study determines the effect of CBD on the viability, apoptosis, morphology and migration of OECM1 cells. Electric cell-substrate impedance sensing (ECIS) is used to measure the change in cell impedance for cells that are treated with a series concentration of CBD for 24 hours. AlamarBlue and annexin V/7-AAD staining assays show that CBD has a cytotoxic effect on cell viability and induces cell apoptosis. ECIS analysis shows that CBD decreases the overall resistance and morphological parameters at 4 kHz in a concentration-dependent manner. There is a significant reduction in the wound-healing recovery rate for cells that are treated with 30 μM CBD. This study demonstrates that ECIS can be used for in vitro screening of anticancer drugs and is more sensitive, functional and comprehensive than traditional biochemical assays. CBD also increases cytotoxicity on cell survival and the migration of oral cancer cells, so it may be a therapeutic drug for oral cancer

The purpose of this study is to examine the match-related performance (scores and penalties) of the athletes in the Junior EJC (European Judo Championship) and U23 EJC categories before and immediately after the Covid-19 quarantine, according to gender and weight category groups. Our sample was based on the junior and U23, male and females, 2019-2020 Junior European Judo Championships and 2019-2020 U23 European Judo Championships. A total of 1431 matches in these tournaments were analyzed: male (n=812) and female (n=619). The main findings of this study showed that most matches in both the male and female categories resulted in ippon (2019-2020 average: 64,35% for Junior male, 70,55% for U23 male and 69,3% for Junior female, 64,4% for U23 female). No significant differences (p > 0.05) were observed between gender and age groups concerning the match scores. In the formation phase of the technique, considerations of high- and low-intensity actions, and analysis of the speed of athletes during matches in official competitions can help to better understand the dynamics of the variability of movements in judo matches. In addition, suggestions are presented to be applied to athletes in different age categories who are on the way to become Olympic athletes.

Timely and accurate information on tree species is crucial for the sustainable management of natural resources, forest inventory, biodiversity detection, and carbon stock calculation. The advancement of remote sensing technology and artificial intelligence has facilitated the acquisition and analysis of remote sensing data, resulting in more precise and effective classification of tree species. Multimodal remote sensing data and deep learning seem to be the current tree species classification research mainstream, whether or not. The current review on the remote sensing data and deep learning tree species classification methods perspectives to analyze the unimodal and multimodal remote sensing data and classification methods in this realm is missing. To bridge the gap, we search for major trends in the remote sensing data and tree species classification methods, provide a detailed overview of classic deep learning-based methods for tree species classification, and discuss the limitations.

In light of the critical and emerging global challenge posed by the increasing frequency and severity of heatwaves in recent decades, this study demonstrates a practical and robust workflow that bridges the gap in understanding how the effective integration of remote sensing data with ground-based observations can facilitate a comprehensive assessment of spatiotemporal heatwave patterns and trends in the central region of Thailand. This research transcends traditional methods, utilizing air temperature (Tair) and satellite-derived land surface temperature (LST) data from 1981 to 2019. Results exhibit that an analysis of Tair indicates increasing daytime heatwaves in peri-urban areas, with significant trends in heatwave number (HWN), heatwave frequency (HWF), and heatwave duration (HWD), heatwave amplitude (HWA) rises in urban settings while nighttime heatwaves significantly intensify in rural locales. Notably, LST trends reveal varied patterns, with peri-urban areas showing marked daytime increases in heatwave magnitude (HWM), HWA, and HWF. Correlation analysis (p=0.05) highlights strong daytime associations between Tair and LST in rural (HWN, HWF, HWD, r>0.90) and peri-urban (HWM, HWA, r>0.65) regions. Overall, this study advances approaches to the adaptable measurement and spatial-temporal pattern of heatwave-related risk areas, providing insights for decision-makers to develop sustainable practices and strategies for climate change adaptation.

Effective oral care is important to maintain a high quality of life. Therefore, plaque control can prevent the development and recurrence of periodontitis. Brushing with a toothbrush and toothpaste is a common way to remove plaque; however, excessive brushing or brushing with abrasive toothpaste can cause wear and tear on the dental crown. Hence, we aimed to quantitatively compare the plaque-removal efficiency and tooth wear of toothbrushes using bioelectric effect (BE) with those of mechanical electric toothbrushes. To generate the BE signal, an electronic circuit was developed and embedded in a toothbrush. Further, typodonts were coated with cultured artificial plaques and placed in a brushing simulator. A toothpaste slurry was applied, and the typodonts were eluted with tap water after brushing. The plaques of the typodonts were captured, and the images were quantified. For the tooth wear experiment, polymethyl methacrylate disk resin blocks were brushed twice a day, and the thickness of the samples was measured. Subsequently, statistical differences between the experimental toothbrushes and typical toothbrushes were analyzed. The BE toothbrush had a higher plaque-removal efficiency and could minimize tooth wear. This study suggests that the application of BE may be a new solution for oral care.

Densely urbanized areas, with a low percentage of green vegetation, are highly exposed to Heat Waves (HW) which nowadays are increasing in terms of frequency and intensity also in the middle-latitude regions, due to ongoing Climate Change (CC). Their negative effects may combine with those of the UHI (Urban Heat Island), a local phenomenon where air temperatures in the compact built up cores of towns increase more than those in the surrounding rural areas, with significant impact on the quality of urban environment, on citizens health and energy consumption and transport, as it has occurred in the summer of 2003 on France and Italian central-northern areas. In this context this work aims at designing and developing a methodology based on aero-spatial remote sensing (EO) at medium-high resolution and most recent GIS techniques, for the extensive characterization of the urban fabric response to these climatic impacts related to the temperature within the general framework of supporting local and national strategies and policies of adaptation to CC. Due to its extension and variety of built-up typologies, the municipality of Rome was selected as test area for the methodology development and validation. First of all, we started by operating through photointerpretation of cartography at detailed scale (CTR 1: 5000) on a reference area consisting of a transect of about 5x20 km, extending from the downtown to the suburbs and including all the built-up classes of interest. The reference built-up vulnerability classes found inside the transect were then exploited as training areas to classify the entire territory of Rome municipality. To this end, the satellite EO HR (High Resolution) multispectral data, provided by the Landsat sensors were used within a on purpose developed "supervised" classification procedure, based on data mining and “object-classification” techniques. The classification results were then exploited for implementing a calibration method, based on a typical UHI temperature distribution, derived from MODIS satellite sensor LST (Land Surface Temperature) data of the summer 2003, to obtain an analytical expression of the vulnerability model, previously introduced on a semi-empirical basis.

To assess the impact of a deep learning (DL) denoising reconstruction algorithm applied to identical patient scans acquired with two different voxel dimensions, representing distinct spatial resolutions. This IRB approved prospective study was conducted at a tertiary pediatric center in compliance with the Health Insurance Portability and Accountability Act. We used a General Electric Signa Premier unit (GE Medical Systems, Milwaukee, WI) to acquire two DTI sequences of the left knee on each child at 3T: an in-plane 2.0 x 2.0 mm2 with section thickness of 3.0 mm and a 2 mm3 isovolumetric voxel, neither had an inter-section gap. We used a multi-band DTI acquisi-tion with fat-suppressed single-shot spin-echo echo-planar sequence (20 non-collinear directions; b-values of 0 and 600 sec/mm2). The MR vendor-provided a commercially available DL model applied with 75% noise reduction settings to same subject DTI sequences at different spatial res-olutions. We compared DTI tract metrics from both DL-reconstructed scans and non-denoised scans for femur and tibia, at each spatial resolution. Differences were evaluated using Wilcox-on-signed ranked test and Bland-Altman plots. When comparing DL versus non-denoised diffu-sion metrics in femur and tibia using the 2 mm x 2mm x 3 mm voxel dimension there were no significant differences between tract count (p = 0.1, p =0.14) tract volume (p = 0.14, p = 0.29), or tibial tract length (p=0.16); femur tract length exhibited a significant difference (p

Accurately estimating shrub biomass in arid and semi-arid regions is critical for understanding ecosystem productivity and carbon stocks at both local and global scales. However, capturing the shrub biomass accurately by satellite observations is challenging due to the short and sparse features of shrubs. In this study, we presented a framework to estimate shrub biomass at a 10m spatial resolution by integrating ground in-situ data, unmanned aerial vehicle (UAV), Sentinel-2, and Sentinel-1 observations. The pilot study was conducted in the Helan mountains of Ningxia province, China. First, the spatial distribution map of shrubland and other land cover types was generated in 2023. Then, a prediction model of shrub biomass was developed in a Random Forest Regression (RFR) approach driven by different predicted variable datasets based on in-situ measurements, UAV, and satellite images. Finally, the developed model was used to produce the biomass map of shrubland in 2023. The uncertainty was characterized by creating a standard deviation (SD) map using the Leave-One-Out Cross-Validation (LOOCV) method in the shrub biomass estimates. The resultant shrubland distribution map in 2023 has an F1 score of 0.92. The shrub biomass model driven by spectral bands and vegetation indices (R2= 0.62) demonstrated superior performance than that only driven by spectral bands (R2=0.33) or vegetation indices (R2=0.55). The uncertainty of the estimated biomass was lower than 4%, with the lowest values (<2%) happening in the high shrub coverage (>30%) and biomass production (>30kg/m2) regions. Furthermore, the findings show that the magnitude of shrub biomass was affected by the aridity and precipitation significantly in the study region. This study provides a workflow to accurately monitor the biomass of shrublands in a complicated environment based on remote sensing images from multi-platform observations.

Remote sensing datasets are increasingly being used to provide spatially explicit large scale evapotranspiration (ET) estimates. The focus of this study was to estimate and thematically map on a pixel-by-pixel basis, the actual evapotranspiration (ET_a) of the Wonji Shoa Sugarcane Estate using the Surface Energy Balance Algorithm for Land (SEBAL), Simplified Surface Energy Balance (SSEB) and Operational Simplified Surface Energy Balance (SSEBop) algorithms. The results obtained revealed that the ranges of the daily ETa estimated on January 25, February 26, September 06 and October 08, 2002 using SEBAL were 0.0 - 6.85, 0.0 – 9.36, 0.0 – 3.61, 0.0 – 6.83 mm/day; using SSEB 0.0 - 6.78, 0.0 – 7.81, 0.0 – 3.65, 0.0 – 6.46 mm/day, and SSEBop were 0.05 - 8.25, 0.0 – 8.82, 0.2 – 4.0, 0.0 – 7.40 mm/day, respectively. The Root Mean Square Error (RMSE) values between SSEB and SEBAL, SSEBop and SEBAL, and SSEB and SSEBop were 0.548, 0.548, and 0.99 for January 25, 2002; 0.739, 0.753, and 0.994 for February 26, 2002;0.847, 0.846, and 0.999 for September 06, 2002; 0.573, 0.573, and 1.00 for October 08, 2002, respectively. The standard deviation of ET_a over the sugarcane estate showed high spatio-temporal variability perhaps due to soil moisture variability and surface cover. The three algorithm results showed that well watered sugarcane fields in the mid-season growing stage of the crop had higher ET_a values compared with the other dry agricultural fields confirming that they consumptively use more water. Generally during the dry season, ET_a is limited to water surplus areas only and in wet season, ET_a was high throughout the entire sugarcane estate. The evaporation fraction (ETrF) results also followed the same pattern as the daily ET_a over the sugarcane estate. The total crop and irrigation water requirement and effective rainfall estimated using the Cropwat model were 2468.8, 2061.6 and 423.8 mm/yr for January 2001 planted and 2281.9, 1851.0 and 437.8 mm/yr for March 2001 planted sugarcanes, respectively. The mean annual ET_a estimated for the whole estate were 107 Mm³, 140 Mm³, and 178 Mm³ using SEBAL, SSEB, and SSEBop, respectively. Even though the algorithms should be validated through field observation, they have potential to be used for effective estimation of ET in the sugarcane estate.

Snow parameters have traditionally been retrieved using discontinuous, multi-band sensors; however, continuous hyperspectral sensor are now being developed as an alternative. In this paper we investigate the performance of various sensor configurations using machine learning neural networks trained on a simulated dataset. Our results show improvements in accuracy of retrievals of snow grain size and impurity concentration for continuous hyperspectral channel configurations. Retrieval accuracy of snow albedo was found to be similar for all channel configurations.

Oncolytic virotherapy is a promising immunotherapy approach for cancer treatment, utilizing viruses to preferentially infect and eliminate cancer cells while stimulating immune responses. In this review we synthesize current literature on the molecular circuits of immune sensing and response to oncolytic virotherapy; focusing on viral DNA or RNA sensing by infected cells, cytokine and danger-associated signal sensing by neighboring cells, and subsequent downstream activation of immune pathways. The sequential sense-and-response mechanisms involve the triggering of molecular sensors by viruses or infected cells to activate transcription factors and related genes for a breadth of immune responses. We describe how molecular signals induced in the tumor upon virotherapy can trigger diverse immune signaling pathways, activating both antigen-presenting cell-based innate and T cell-based adaptive immune responses. Insights into these complex mechanisms provide valuable knowledge for enhancing oncolytic virotherapy strategies.

The review scrutinizes the currently performed research on the new methods for enhancing bituminous binder performance through radiation and radical grafting of polymer modifers of bitumen. It investigates innovative methods, including using waste polymers as modifiers, and applying radiation for polymer grafting, to overcome challenges like high costs, low aging resistance and storage stability issues, of which separation of phases polymer/bitumen is the most significant obstacle. These advanced modification techniques promise sustainability through the decrease of the carbon footprint of transportation systems by improving the properties and durability of binders. Additionally, the review discusses the parameters and mechanistic aspects from a scientific perspective, shedding light on the underlying processes that contribute to the improved performance of modified bituminous binders.

In this paper, a novel permanent magnet-assisted synchronous reluctance machine (PMASynRM) with rare-earth PMs and ferrite magnets is proposed. The performance of PMASynRM is discussed with respected to the different magnet ratio of rare-earth PMs and ferrite magnets. Some characteristics including the flux density, output torque, cogging torque, output power, power factor, torque ripple, loss, efficiency, and demagnetization are calculated by 2-D finite element analysis (FEA). The analysis results show that the excellent performance can be obtained by using hybrid magnet of rare-earth PMs and ferrite magnets with the suitable magnet ratio, and provide some desirable cost-performance trade-off.

Assessment of extreme events and climate change on reservoir inflow is important for water and power stressed countries. Projected climate is subject to uncertainties related to climate change scenarios and Global Circulation Models (GCMs’). Extreme climatic events will increase with the rise in temperature as mentioned in the AR5 of the IPCC. This paper discusses the consequences of climate change that include extreme events on discharge. Historical climatic and gauging data were collected from different stations within a watershed. The observed flow data was used for calibration and validation of SWAT model. Downscaling was performed on future GCMs’ temperature and precipitation data, and plausible extreme events were generated. Corrected climatic data was applied to project the influence of climate change. Results showed a large uncertainty in discharge using different GCMs’ and different emissions scenarios. The annual tendency of the GCMs’ is bi-vocal: six GCMs’ projected a rise in annual flow, while one GCM projected a decrease in flow. The change in average seasonal flow is more as compared to annual variations. Changes in winter and spring discharge are mostly positive, even with the decrease in precipitation. The changes in flows are generally negative for summer and autumn due to early snowmelt from an increase in temperature. The change in average seasonal flows under RCPs’ 4.5 and 8.5 are projected to vary from -29.1 to 130.7% and -49.4 to 171%, respectively. In the medium range (RCP 4.5) impact scenario, the uncertainty range of average runoff is relatively low. While in the high range (RCP 8.5) impact scenario, this range is significantly larger. RCP 8.5 covered a wide range of uncertainties, while RCP 4.5 covered a short range of possibilities. These outcomes suggest that it is important to consider the influence of climate change on water resources to frame appropriate guidelines for planning and management.

A low-cost bio-mass-derived carbon substrate has been employed to synthesize MoS₂@carbon composites through a hydrothermal method. Carbon fibers derived from natural cotton provide a three-dimensional and open framework for the uniform growth of MoS₂ nanosheets, thus constructing hierarchically coaxial architecture. The unique structure could synergistically benefit fast Li-ion and electron transport from the conductive carbon scaffold and porous MoS₂ nanostructures. As a result, the MoS₂@carbon composites, when served as anodes for Li-ion batteries, exhibit a high reversible specific capacity of 820 mAh g^-1, high-rate capability (457 mAh g^-1 at 2 A g^-1), and excellent cycling stability. The superior electrochemical performance makes the MoS₂@carbon composites to be low-cost and promising anode materials for Li-ion batteries.