The aim of this study was to evaluate the effect of two different insertion speeds at 8 different insertion torque values ranging from 25-60 during implantation in a dense polyurethane D1 bone model on the placement status and removal torque of dental implants. In this study, 50 pcf single layer polyurethane plates were used. In the study, a total of 320 implant sockets were divided into 2 groups as Group 1 (30 rpm) and Group 2 (50 rpm) in terms of insertion speed. Group 1 and Group 2 were divided into 8 subgroups as 25, 30, 35, 40, 45, 50, 55 and 60 torques. There were 20 implant sockets in each subgroup. During the implantations, implant placement status and removal torque values were assessed. There was a statistically significant difference between the 30 and 50 RPM groups in terms of overall implant placement status (p<0.01). It was found that the removal torque values at 50 RPM were statistically significantly higher than those at 30 RPM (p<0.01). This study showed that in dense D1 bone, the minimum parameters at which all implants could be placed at bone level were 50 torque at 30 rpm and 40 torque at 50 rpm.

Background: This study stands as a pioneer in the histological evaluation of the biological behavior of a novel implant design featuring decompressive cervical blades. Hence, the aim of the present study was to evaluate the healing outcome in cortical regions at where decompressive protocols were adopted using implants equipped with blades. Materials and methods: Blades with varying diameters were integrated into the coronal portion of the implant to prepare the cortical region of rabbit tibiae. The blade diameters differed from the implant collar by the following amounts: control group (0 µm), +50 µm, and +200 µm. Results: No marginal bone loss was detected. Instead, all implants exhibited new bone formation in the coronal region. Complete closure was observed in the CG-0 group, as well as in the TG-50 and TG-200 groups, despite the presence of marginal gaps without primary bone contact at installation. In the apical region, most implants breached the cortical layer. Nevertheless, new bone formation in this region completely closed the osteotomy, effectively isolating the internal environment of the tibia from the external. Conclusions: The use of a blade attached to the implant body enabled precise preparation of the cortical layer, allowing for controlled decompression in the targeted area. This technique resulted in optimal osseointegration with no loss of marginal bone, and complete restoration of marginal gaps ranging from 0 µm to 200 µm.

(1) Background : When placing implants in the maxillary posterior region with insufficient alveolar bone, a maxillary sinus elevation is necessary. Autogenous bone, though biologically ideal, poses risks and discomfort due to donor site harvesting. Block-type autogenous tooth bone graft material, made from the patient’s own extracted tooth, offers similar biological stability without these drawbacks; (2) Methods : This study observed the progress of 19 implant patients who were treated with maxillary sinus elevation procedures using block-type autogenous tooth bone graft material at the Daegu Catholic University Medical Center. Extracted teeth were processed into demineralized tooth block bone. After elevating the sinus membrane, implants and the tooth bone graft material were placed in the space, and the bony window was repositioned. Postoperative evaluations through clinical observation and radiographic imaging assessed sinus membrane elevation, alveolar bone height increase, and implant osseointegration; (3) Results : Results showed proportional increases in alveolar bone height to the graft material size, with long-term stability. No postoperative complications occurred, even with sinus membrane perforation, and implants remained stable; (4) Conclusions : The study concludes that maxillary sinus lifts using block-type autogenous tooth bone graft material provide excellent bone induction and biocompatibility, making it a highly beneficial method for both dentists and patients.

The aim of this study was to evaluate the use of a flexible synthetic polymer bone graft to provide implant stability in the absence of implant stability during implant placement in a dense cortical bone model. Sockets were prepared on polyurethane blocks according to the standard implant socket drilling protocol in the control group, both oversizing and deepening in group 2, and oversizing only in group 3. In groups 2 and 3, flexible synthetic polymer bone grafts were placed in the sockets prior to implant placement. The implants were placed at bone level in all groups. The highest torque value obtained was recorded as the insertion torque. 75 implant sites in 3 groups were included in the study. The torque values of the implants in the control group were significantly higher than those of the implants with the oversized and deepened sockets and the oversized-only sockets (p<0.05; p<0.01).The torque values of the implants with the oversized and deepened sockets were significantly higher than those of the implants with the oversized-only sockets (p<0.01). In this study, flexible synthetic polymer bone graft was shown to be effective in achieving implant stability in the management of implants with loss of primary stability.

Periodontitis is a chronic inflammatory disease which results in the destruction of the tooth’ s supporting tissues and the alveolar bone resorption. The complement becomes a major link between infection and inflammatory pathology including periodontitis. Gingipians as important virulence factors of P. gingivalis have the activity of C5 convertase, could cleave C5 into fully functional C5a to activate C5aR. The above process could be blocked by the C5aR antagonist (PMX-53) to suppress local periodontal inflammation, and then achieves the purpose of treatment of periodontitis. Nanoparticles incorporated within gelatin are promising carrier system for drug delivery in recent years. This study aimed to investigate whether gelatin nanoparticles loaded with PMX-53 prevents alveolar bone resorption in miniature swines model of periodontitis. Four miniature swines were placed ligatures around the maxillary and mandibular fourth premolar and first molar on both sides for seven weeks to induce periodontitis. Then, animals were assigned randomly to four groups: minocycline-treated group, gelatin with PMX53-treated group, gelatin-treated group and a sham control group. They were treated with 1ml related drugs respectively, into gingival sulcusl for 4 times at one-week intervals. We showed that local treatments with gelatin nanoparticles loaded with PMX-53 could inhibit alveolar bone loss of periodontitis. Our study revealed that gelatin nanoparticles loaded with PMX-53 prevented alveolar bone resorption miniature swines model of periodontitis. In addition, provided proof-of-concept for local targeting of gelatin nanoparticles loaded with PMX-53 as a powerful candidate for the treatment of periodontitis.

Objective. The present study examined the potential use of computed tomography panoramic mandibular indices on cone beam CT (CBCT) for the assessment of bone density in postmenopausal women with low bone mass. Study design. We enrolled 104 postmenopausal women who performed dual energy X-ray absorptiometry (DXA) using a DXA scanner and mental foramen region CBCT using NewTom VGi EVO Cone Beam 3D system. We assessed the relationship between DXA parameters: lumbar, femoral neck and total hip T score, bone mineral density (BMD), and lumbar trabecular bone score (TBS) and the panoramic mandibular indices: computed tomography mandibular index superior (CTI(S)), computed tomography mandibular index inferior (CTI(I)) and computed tomography mental index (CTMI). Results. We found important correlations between the CTI(I), CTI(S) and CTMI and bone mass, quantitative evaluated as BMD and T-score and also quality using TBS score. Conclusion. CBCT measured indices CTI(S), CTI(I), CTMI are useful in assessing patients with low bone mass.

We report the case of a 61-year-old woman who was referred to the Oral Surgery and Implantology Unit of the University Hospitals of Geneva to take care edentulous sites after dental avulsions of teeth 11 and 21 following traumatic shock due to endotracheal intubation under general anaesthesia. The dental history revealed that the patient had a history of generalized chronic periodontitis that had been treated several years earlier. Treatment consisted, for the first time to our knowledge, of immediate insertion of implants at sites 11 and 21 with simultaneous bone augmentation in a single surgical procedure and immediate restorations.

Vertical and horizontal bone augmentation is one of the most challenging techniques in bone engineering. The use of barrier membranes and scaffolds in guided bone regeneration (GBR) procedures is a common approach for the treatment of lost bone around teeth and dental implants. The aim of this study was to estimate the barrier effects of a synthetic poly (lactic acid/caprolactone) [P(PA/CL)] bilayer membrane for GBR, compared to a porcine collagen bilayer membrane, in the vertical augmentation model on 10–12-months old rat skull without periosteum. The HAp block (diameter: 4 mm, height: 3 mm, porosity:75%, average pore size:150 μm) was placed on the rat skull without a periosteum. The P(LA/CL) membrane (solid layer: 25 μm, porous layer: 175 μm) or the collagen membrane (solid layer, porous layer) was applied onto the HAp block. At 3, 6, and 12 weeks after the surgery, the incised tissues were fixed, decalcified, and stained with hematoxylin and eosin for histological evaluation. The P(LA/CL) membrane remained until 12 weeks and could achieve barrier effects to inhibit cellular invasion from the repositioned soft tissues. Local bone formation occurred in the interconnected pores of HAp at 6 weeks. On the other hand, the collagen membrane did not inhibit cellular invasion for its expansion until 3 weeks, and was absorbed until 6 weeks. The results indicated that the P(LA/CL) membrane might be effective in GBR as occlusive absorbable membrane.

Several types of guided bone regeneration materials are available with various properties and clinical indications. Among them, dentin-derived matrix from extracted teeth is an excellent alternative to traditional graft materials, such as allografts and xenografts. Different clinical preparation protocols exist: block form versus powder form, demineralized versus non-demineralized form. Out of these methods, demineralization protocols for dentin-derived matrix from extracted teeth have been noted for a wide range of successful clinical outcomes. The purpose of this animal study was to find out the most effective method of demineralizing dentin-derived matrix to result in the highest regenerative ability in the bone graft material in rabbit calvaria. The study conducted a comparative histomorphometric analysis of four groups in distinguished matrix conditions: a control group without graft placement, a non-demineralized dentin-derived matrix graft placement group, a 15-minute demineralized dentin-derived matrix graft placement group, and a 30-minute demineralized dentin-derived matrix graft placement group. Regenerative processes were evaluated three times at 2, 4, and 8 weeks post-graft placement. These groups of rabbits were evaluated randomly in a blinded setting to prevent bias. Among the four groups compared, the group with a 15-minute demineralized dentin-derived matrix graft showed the most efficient bone regeneration in the histomorphometric analysis. Based on this animal study, it was apparent that a 15-minute demineralization of dentin-derived matrix is the preferred preparation protocol to maximize the regenerative potential in the matrix.

This review examines the effects of lingonberry (Vaccinium vitis-idaea L.) on general and oral health. The effects of lingonberry are based on the vitamins, minerals, fibers and polyphenolic compounds it contains. Lingonberry's bioactive substances have a diverse range of antimicrobial, anti-inflammatory, antiproteolytic, anticarcinogenic and antioxidant properties. Research results suggest that lingonberries can have a positive effect on human health. Berries, lingonberry juice/lingonberry nectar/fermented lingonberry juice and polyphenol fractions have been used in clinical studies. Lingonberries balance post-meal blood sugar, free fatty acids and insulin levels. Fermented lingonberry juice reduces Streptococcus mutans, Candida and periodontal pathogen counts, but is probiotic because it favors growth of Lactobacilli. In addition, it increases saliva secretion and thus lowers the risk of oral infections. It lowers the clinical parameters of periodontitis and the active matrix metalloprotease-8, reducing the low-grade inflammation associated with periodontal diseases. More studies on humans are needed.

Ectopic eruption of teeth rarely occurs in the mandibular condyle, orbit, nasal cavity, skin, and maxillary sinus. Ectopic eruption of teeth in the maxillary sinus can be accompanied by chronic and recurrent sinusitis, including headache, facial pain, and numbness. Fibro-osseous lesions in the paranasal sinuses are discovered incidentally on X-ray images and are often asymptomatic. Osteoma is the most common fibro-osseous lesion that develops in the paranasal and nasal sinuses. Herein, we report a rare case of osteoma (exostosis) containing supernumerary teeth within the maxillary sinus. A characteristic pedicled bone lesion with a clear border on computed tomography was the undefined orthopantomogram radiopacity in the left maxillary sinus, and the lesion contained teeth. The tumor was excised using the Caldwell–Luc procedure. Pathologically, the surgical specimen revealed an osteoma. The patient’s symptoms of chronic sinusitis disappeared, and the patient had no symptoms 2 years after the surgery. Because the patient had no history of midface trauma or surgery, the supernumerary teeth were speculated to have migrated during a reactive osteogenic process caused by chronic sinusitis.

Immune checkpoint inhibitors (ICIs), including anti-programmed cell death 1 ligand 1 (PD-L1) antibodies, are significantly changing treatment strategies for human malignant diseases including oral cancer. Cancer cells usually escape from immune system and acquire proliferative capacity and invasive/metastatic potential. We have focused on the two immune checkpoints, PD-1/PD-L1 and CD47/SIRPα in the tumor microenvironment of oral squamous cell carcinoma (OSCC), and performed a retrospective analysis of the expression of seven immune-related factors (PD-L1, PD-1, CD4, CD8, CD47, CD56 and CD11c), and examined their correlation with clinicopathological status. As a result, there were no significant findings relating seven immune-related factors and several clinicopathological statuses. However, the immune-checkpoint related factors (PD-1, PD-L1, CD47) were highly expressed in non-keratinized epithelium-originated tumors when compared to those in keratinized epithelium-originated tumors. It is of interest that immunoediting via immune checkpoint-related factors was facilitated in non-keratinized sites. Several researchers reported that keratinization of oral mucosal epithelia affected the immune response, but our present finding is the first study to show a difference of the tumor immunity in the originating-epithelium of OSCC, keratinized or non-keratinized. Tumor immunity, an immune escape status of OSCC might be different in the originating-epithelium, keratinized or non-keratinized.

The aim of this study was to compare the effect of using L-PRF in patients undergoing impacted lower third molar surgery with either primary or secondary closure techniques. Methods: This prospective, randomised, double-blind, split-mouth clinical trial was conducted in patients with bilateral lower impacted third molars of similar position. Primary closure was performed in group 1 and secondary closure in group 2. Group 1 closure technique was applied to one side of the patients and group 2 closure technique was applied to the other side at different times. Nine pa-tients were excluded from the study due to alveolitis and failure to attend regular control visits out of the 45 patients evaluated. Results: Of the 36 patients included in the study, 23 were female and 13 were male and the mean age was 22.42±3.36 years. The secondary closure group had lower VAS scores at hour 6 (p

Purpose: The purpose of this study is to apply the Composite Radiographic Index modified (CRIm) in CBCT scans of patients with Medication related osteonecrosis of the jaws (MRONJ) in order to detect its validity, and corelate the radiologic findings with the clinical staging of the disease. Methods: This study included 43 patients with MRONJ diagnosis and CBCT scans performed in the School of Dentistry and approved by the Research Ethics Committee. Clinical staging for every patient (0-3) was provided according to AAOMS 2022 guidelines. In cases of patients with both jaws affected, each jaw was evaluated independently resulting to 52 CBCT scans. The 52 CBCT scans were assessed under standardized viewing conditions by 2 observers who evaluated independently the following 8 radiologic features: lytic changes, sclerosis, periosteal reaction, sequestration, non-healing extraction sockets and other findings (sinus implication, inferior alveolar canal involvement, jaw fracture). The CRIm index was constructed to assess the extent of osseous changes. The radiologic features were scored as absent (0), localized/single (1), extensive/multiple (2), yielding a theoretical range of 0–12. For statistical analysis Fisher’s exact test and Spearman’s correlation coefficient were performed. Results: A statistically significant association of clinical stage with lytic changes, sequestration and inferior alveolar canal involvement was found. Also, a statistically significant correlation of clinical stage with CRIm index classification was obtained. Conclusions: The CRIm index tends to increase as the clinical stages of MRONJ advance, suggesting a correlation between the clinical stage of MRONJ and the CRIm index.

Background and Objectives: The aim of this study was to determine the job-related and individual features that influence BS and depression levels among dentists working in faculties, oral and dental health centres (ODHC) and private clinics. Materials and Methods: This prospective, cross sectional study was carried out on dentists working in different regions of Turkey. Data were collected using an on-line questionnaire created using Google Forms. The questionnaire consisted of demographic data, Maslach BS Inventory (MBI) and Beck Depression Inventory (BDI) sections. Demographics were age, height, weight, marital status, blood type, gender, monthly income, income satisfaction and having enough free time. The dentists were divided into 3 groups as faculty, private clinic and ODHC according to the institutions in which they worked. Results: Of the total 290 dentists enrolled in the study, there were 172 males and 118 females with a mean age of 36.98±5.6 years. 128 of the dentists worked in faculties, 72 in private clinics and 90 in ODHCs. It was observed that women's EE scores were higher than men's (P<0.05). No statistically significant difference was found between the groups when comparing BS and depression scores according to marital status and blood group (P>0.05). There was no significant relationship between emotional exhaustion (EE), depersonalisation (DP), personal accomplishment (PA) and depression scores according to age, BMI and work experience, age, work experience and BMI (P<0.05). It was found that the EE scores of the dentists working in the faculty and private clinic were lower than those of the dentists working in the ODHC (P<0.05). Monthly income was associated with depression (r = -0.35). Conclusions: This study showed that dentists working in ODHCs had more EE. These findings suggest that there is a need for improvement in the working conditions of dentists, particularly in ODHCs.

Objectives: Aim to assess the perceptions of virtual learning among dental residents and faculty and employ Regulatory Focus Theory (RFT) to understand the impact of motivational orientations on virtual learning during COVID pandemic. Methods: 46 dental residents and 10 faculty in Upstate New York participated in the study (June -August 2021). Questionnaires were used to collect demographics, perceptions of virtual learning, burnout, and RFT types (promotion and prevention focus). Multiple regression analyses were used to examine factors associated with perceptions of virtual learning and burnout. Results: Overall, 70% of residents and 44% of faculty found virtual learning effective. Younger residents with less experience preferred virtual learning more than their older, experienced peers. Residents trained outside the U.S. and Canada favored in-person learning more than those trained within. Furthermore, residents with a higher promotion focus score found virtual learning more interactive for didactic courses. Additionally, 52% of residents experienced burnout, with a higher incidence among females (p=0.044). Conclusions: Virtual learning is well-received by dental residents and faculty, with potential for continued use post-pandemic. Future efforts should focus on creating an inclusive and supportive educational environment that meets the motivational and well-being needs of dental residents and faculty.

Keywords: Vascular Malformation, Diode Laser, Angioma, Blue light, Conservative

The objective of this study was to compare single-needle arthrocentesis with the conventional two-needle arthrocentesis, as well as, additional intracapsular injection of hyaluronic acid or platelet rich fibrin. 96 patients with established osteoarthritis (OA) (n= 48) or with internal de-arrangement (DD) (n= 48) were assigned for single-needle arthrocentesis with distension of the joint or conventional two-needle arthrocentesis with or without intracapsular injection of the medication (hyaluronic acid- HA or platelet-rich plasma- PRP) performed every month in the period of 6 months. The maximum mouth opening and pain as measured by the visual analog scale (VAS) were compared. Each group exhibited significant improvement: decrease of pain and in-creased mouth opening. Single- puncture technique provided similar pain reduction as two needle approach but provided significantly better results in maximum mouth opening. Reduction of pain was similar when comparing between the OA and DD cohorts, however patients with disc dis-placement reached significantly better mouth opening than OA. Intracapsular application of medication contributed to significant decrease of pain in both HA and PRP groups, with plate-let-rich fibrin being significantly superior in terms of mouth opening increase over HA.

Dirofilariosis is an infectious disease caused by species of the Dirofilaria genus. It is manifested by the appearance of a subcutaneous swelling, especially in the eye region. We present the case of a 29-year-old patient that accused facial asymmetry in the right genian region. Following clinical and paraclinical evaluations, the diagnosis of parasitic cyst was established in the context of dirofilariosis with Dirofilaria repens (D. repens). Treatment consisted of surgical excision of the formation associated with prophylactic antibiotic medication. Macroscopic analysis of the excision piece revealed a structure that contains a cystic cavity and a filamentous form with a length of approximately 10 mM and a diameter of 1 mM. This is the first case of dirofilariosis located in the genian region reported in Romania. The overview of this pathology is important to raise awareness among physicians about its presence and its clinical variations.

Background and Objectives: The complications seen after lower impacted third molar surgery affect the quality of life of the patients. The aim of the study was to investigate the efficacy of a single preoperative dose of deflazacort on pain, swelling and trismus following impacted lower third molar surgery. Materials and Methods: This randomised, prospective, double-blind, split-mouth clinical study included 30 healthy individuals with bilaterally impacted lower third molars that was removed for orthodontic purposes between September 2017 and September 2018. Group 1 was given a placebo (single dose vitamin C tablet) and group 2 was given a single 30 mg dose of deflazacort 1 hour prior to the surgery. Pain was evaluated using the visual analog scale for 1 week postoperatively. Edema (in mm) and trismus (in mm) were evaluated preoperatively and on postoperative days 2 and 7. The Mann-Whitney U test was applied for group analysis. p values < 0.05 were considered statistically significant. Results: When postoperative pain scores were evaluated, a significant difference was found between the groups only at the 6th and 12th hours (p0.05). Even high trismus values were recorded on the 2nd day, it was observed that the trismus resolved on the 7th day. There were no significant differences in trismus between the groups at any time point (p>0.05). Evaluation of swelling showed that there was no statistically significant difference between the study and control groups at any time point (p>0.05). No side effect was detected in both the study and the control groups. Conclusions: This was the first split-mouth study evaluating the anti-inflammatory effect of deflazacort after lower impacted third molar surgery. A single dose of 30 mg deflazacort was shown to be effective in reducing pain at 6 and 12 hours postoperatively.

The assortment of low-cost 3D printers for “in-practice” use, e.g., for clear aligner therapies, is ever increasing. To address concerns about the accuracy of orthodontic models produced on such printers when cost efficient modes of 3D printing are employed, this study examined the effect of print model body type and print angulation on accuracy. Six printing-configuration groups were included: 2 model types (solid or hollow shell) combined with 3 print angles (0°, 70°, or 90°) with 10 models/group; all models were printed with 100-µm layer thickness using a digital light processing-based 3-dimensional printer. Eleven selected structures and distances were measured on the printed models with a digital microscope and compared to the same measures on a digitized master model. The clinically-acceptability range was set at ±0.25 mm difference from the master model for single tooth measurements (intra-tooth) and ±0.5 mm for cross-arch measurements (inter-tooth). For individual measurements across all models, 98% fell within clinical acceptability. For mean measurements within each model group, only canine height for the shell-0° model had a mean difference (0.26 mm ± 0.03) outside the clinically acceptable range for intra-tooth measurements. Standard deviations for all intra-tooth measurements were within 0.07 mm. While none of the mean inter-tooth measurements exceeded the acceptability range, the standard deviations were larger (0.04 to 0.30 mm). Accuracy of orthodontic models for clear aligner therapies was not impacted beyond the clinically acceptable range when altering model body type and print angulation to improve efficiency of 3D printing. These findings suggest greater flexibility of the practitioner to alter print settings to address time and cost efficiency in various clinical scenarios and still maintain clinically acceptable model accuracy.

Little has been written in literature about the clinical comparison of the single use of chlorhexidine (CHX) rather than its combination with cetylpyridinium chloride (CPC). The purpose of this study was to compare the clinical effectiveness of two at-home antiseptic regimens. Healthy subjects scheduled for dental surgery were enrolled. After the surgery, patients were randomly allocated in a first group (Group A) which received a manual ultra soft toothbrush (Mentadent Professional®), an antiseptic toothpaste with 0,12% CHX and Vitamin B3 (Mentadent Professional Azione Intensiva Gengive®) and an antiseptic mouthwash with 0,12% CHX and 0,07% CPC. The second group (Group B) received solely an antiseptic mouthwash with 0,2% in conjunction with Anti Discoloration System (Curasept ADS/DNA®) and were encouraged to use their usual toothbrush and toothpaste. Patients were instructed to use the products twice a day and to rinse for 30 seconds. On day 7, patients were examined for the Early Healing Score, Visual Plaque Index of the sutures, Numerical Rating Scale and mouthwash taste. Group A showed a statistically significant levels of EHS and taste satisfaction. The regimen based on CHX associate with vitamin B3 in the toothpaste and CPC in the mouthwash resulted in superior clinical outcomes and satisfaction compared to solely CHX.

Background: The implementation of tyrosine kinase inhibitors (TKIs) in the treatment of chronic myeloid leukemia (CML) has brought a significant improvement in the prognosis for CML patients and a decrease in the number of patients requiring allogeneic hematopoietic stem cell transplantation (allo-HCT). Nevertheless, the impact of TKIs on allo-HCT outcomes have not been thoroughly explored. Objectives: The main endpoint of our research was to assess the impact of prior TKI treatment on acute graft-versus-host disease (aGvHD) and chronic graft-versus-host disease (cGvHD). Methods: In our retrospective analysis we included 240 patients treated between 1993 and 2013, and divided them into 3 groups according to the therapy administered prior to matched related or matched unrelated donor allo-HCT (imatinib group n=41, dasatinib/nilotinib group n=28, TKI naïve group n=171). Results: Both the cumulative incidence of aGvHD (p=0.044) and cGvHD (p&lt;0.001) in individuals receiving second generation TKIs (2G-TKIs) prior to allo-HCT compared to patients receiving no TKIs or imatinib (IMA) (40.7% vs 61.4% vs 70.7%, p=0.044; 25.0% vs 76.4% vs 51.2%, p&lt;0.001, respectively). In case of the 2G-TKI cohort, the number of low-grade aGvHD and cGvHD was significantly lower compared to the IMA and TKI-naïve groups (p=0.018, p=0.004; p&lt;0.001 versus TKI-naïve, respectively). In terms of 3-year overall survival (OS) there were no important variations between TKI-naïve, IMA and 2G-TKI (55% vs 49.9% vs 69.6%, p=0.740). Conclusions: The results of our study suggest that TKI treatment prior to allo-HCT may have protective impact on immune-mediated outcomes.

Background: Two explored EDA1 variants regulate the biological behaviors of human dental pulp stem cells (hDPSCs), such as proliferation and migration, as well as their effects on odontogenic differentiation, providing a theoretical basis for further exploration of the mechanisms underlying EDA1-induced tooth development. Methods: The experimental groups included a wild-type EDA1 group (Wt), non-syndromic tooth agenesis variants EDA1 group (NSTA-A259E, NSTA-S374R), syndrome type variant EDA1 group (STA-H252L), and an empty vector control group (PCR3/NC). CCK-8 method was used to investigate the proliferative activity of hDPSCs. The cell cycle distribution of hDPSCs was detected by flow cytometry; The cell migration ability was assessed using the cell scratch and Transwell tests; Odontogenic differentiation medium was used to induce mineralization of hDPSCs, followed by statistical analysis. RNA-Seq revealed that FOS, JUN and other genes were found to be enriched in MAPK signaling pathway and osteoclast differentiation pathway. qPCR was used to detect mRNA expression of hub genes (FOS and JUN). Results: Compared with the NSTA-EDA1 and STA-EDA1, Wt-EDA1 promotes the proliferation and transformation of hDPSCs from the G0/G1 phase to S phase (p<0.01), with no significant difference between NSTA-EDA1 and STA-EDA1 (p>0.05). Wt-EDA1 also upregulated hDPSCs cell migration compared to NSTA-EDA1 and STA-EDA variants, as demonstrated by migration assays (p<0.01). NSTA-EDA1 and STA-EDA1 variants inhibited the odontogenic differentiation of hDPSCs compared to the Wt group, as shown by Alizarin red staining and ALP staining (p<0.01). RNA sequencing revealed that the differentially expressed genes FOS and JUN were enriched in the MAPK signaling pathway and osteoclast differentiation. Compared with Wt-EDA1, EDA1 variants lost the ability to promote c-FOS mRNA expression, as confirmed by qPCR. Conclusions: EDA1 variants fail to the promote c-FOS mRNA expression in hDPSCs, thereby inhibiting odontogenic differentiation and losing the ability to enhance the proliferation of hDPSCs.

Background: To prevent excessive compression of the cortical layer, which can lead to marginal bone loss, various companies have introduced specialized drills. However, these drills often lack the necessary precision, as the operator’s hand may not be stable enough to prevent ovalization and over-widening, nor precise enough to maintain coaxial alignment. Therefore, the aim of this study was to develop a device capable of achieving calibrated cortical preparation in terms of both dimension and coaxiality. Methods: A machining technology based on drilling principles was employed to create the device. Results: Nine blades were incorporated between the transmucosal neck and the implant threads, enabling the blades to cut the cortical bone coaxially during the implant insertion process. Conclusions: The implant with integrated blades was engineered to facilitate precise cortical bone preparation, ensuring both accurate dimensions and coaxial alignment. This ensures that the radial compressive stresses transmitted from the implant to the peri-implant bone during surgery can be precisely controlled. The experimental study outcomes discussed in this article validate the effectiveness of the implant design.

This study aims to provide an updated overview of the systematic evaluation and management of Post-Traumatic trigeminal neuropathic pain (PTTN) resulting from dental procedures or trauma. PTTN arises following an injury to the trigeminal nerve, which is responsible for sensory and motor functions in the maxillofacial region. The etiology encompasses various dental procedures and craniofacial trauma, leading to a spectrum of symptoms, from tingling to severe pain. Diagnostic challenges stem from the absence of standardized criteria and the overlap with focal neuralgia, necessitating comprehensive evaluation. Misdiagnosis can result in prolonged suffering and unnecessary procedures. Successful management hinges on prompt diagnosis and interdisciplinary collaboration, with early intervention crucial in mitigating chronicity. While nerve recovery post-trauma is challenging, preventive measures through accurate evaluation and treatment are paramount.  Management for PTTN includes non-invasive and surgical interventions. Non-invasive intervention includes systematic and local pharmacological management. This review enhances uniformity in PTTN evaluation and treatment approaches despite standardized study limitations.

Oral candidiasis is a common problem among immunocompetent patients. The frequent resistance of Candida strains to popular antimycotics makes it necessary to look for alternative methods of treatment. The authors conducted a systematic review following the PRISMA 2020 guidelines. The objective of this review was to determine whether curcumin-mediated aPDT and blue light could be considered as an alternative treatment for oral candidiasis. PubMed, Google Scholar and Cochrane Library databases were searched using a combination of the following keywords: (Candida OR candidiasis oral OR candidosis oral OR denture stomatitis) AND (curcumin OR photodynamic therapy OR aPDT OR photodynamic antimicrobial chemotherapy OR PACT OR photodynamic inactivation OR PDI). The review included in vitro laboratory studies with Candida spp., in vivo animal studies, and randomized control trials (RCTs) involving patients with oral candidiasis or prosthetic stomatitis, published only in English. The method of elimination of Candida species in the studies was curcumin-mediated aPDT. 757 studies were identified. Following the analysis of the titles and abstracts of the studies, only 42 studies were selected for in-depth screening, after which 26 were included in this study. All studies evaluated the antifungal efficacy of curcumin-mediated aPDT against C. albicans and non-albicans Candida. In studies conducted with planktonic cells solutions, seven studies demonstrated complete elimination of Candida spp. cells. The remaining studies demonstrated only partial elimination. In all cases, experiments on single-species yeast biofilms demonstrated partial, statistically significant inhibition of cell growth and reduction of biofilm mass. In vivo, curcumin-mediated aPDT has shown good antifungal activity against oral candidiasis also in an animal model. However, its clinical efficacy as a potent therapeutic strategy for oral candidiasis requires further RCTs.

We present a case report of a 26-years-old female suffering from Coffin Siris Syndrome, who underwent orthodontic treatment and surgery to solve her malocclusion and improve her aes-thetics and functional occlusion. Methods: The presurgical phase involved multibracket self-ligating attachments, Damon prescription. The patient underwent maxillofacial surgery to correct the severe skeletal malocclusion and relocate the bone bases in the right relationship. The post-surgical orthodontic treatment was performed to complete the alignment. Results: The pa-tient improved her aesthetics and functional abilities. Conclusions: Syndromic patients can un-dergo orthodontictreatment if comorbidities and collaboration allow it. Support and collaboration of families and psychotherapists must be considered, but clinical cases of syndromic patients can be faced and solved. Obviously, each syndromic patient is considered unique, and the risk-benefit ratio must be correctly assessed for each one.

Mesenchymal stem cells due to their multipotent ability are considered one of the best candidates to be used in regenerative medicine. The most used source of those stem cells long the last decades was the bone marrow, despite its limited cell resources and the painful and very invasive surgical treatment. Therefore, the scientific community investigated many alternative sources for the harvesting of these stem cell subpopulations. Adipose tissue attracted the biggest interest thanks to special features, such as great tissue abundance, easy availability, and in the end the large amount of positive mesenchymal stem cells. Once it was verified that these stem cell subpopulations possess the same bone marrow differentiation potential, it became evident that they would be the ideal candidate to be used in regenerative and tissue engineering applications. Even the regenerative use of these cells long become a sensitive point because not all the acquired phenotypes resulted in the best source for plastic procedures. As documented in the literature, the ideal fillers for regenerative is represented by stem cell population. Therefore, it became crucial to investigate any kind of biological mechanism on the differentiative ability of those mesenchymal stem cells, especially their regulative factors. One of the most studied and important regulators are the miRNAs. Indeed, miRNA play a crucial role in the differentiation process of adipose stem cell cultures isolated from patients or obtained by commercial cell lines toward osteocytes, chondrocytes, and adipocytes differentiated populations.

Although researchers have proposed various indentation size effect (ISE) models, these models often involve different form and number of parameters that can make our wonder which is the best in existed ISE models. Three types of ISE test data, namely, normal ISE, reverse ISE and transition of normal to reverse ISE, are used to evaluate the sixteen ISE models. The comparatively study indicates that H-J, N-G-Fs, N-G-H, N-G-A and N-G-Qs models can accurately predict the normal ISE. The reason for this is that the friction stress that is not related to dislocation activities or the indentation size effect of plastic zone has been introduced into these models. Therefore, these two factors should be considered in future ISE models. The sixteen ISE models are originally proposed to describe the normal ISE of different materials. However, to our surprise, some of these models are able to capture the reverse ISE and the transition of normal to reverse ISE of different materials. The determination coefficients (DC) of the sixteen ISE models are also determined for different materials. For reverse ISE, the highest DC value for NiCSi, TC4 and PED Ni are given by the EXP, N-G-Fs and N-G-A models, respectively. For the transition of normal to reverse ISE, the N-G-YC, N-G-Fs, and N-G-H models produce the maximum DC for ZrO2, Cu and Y2O3-ZrO2, respectively. Moreover, the mean DC of the N-G-Fs model is the maximum among the sixteen ISE models, followed by the N-G-H model, but they cannot accurately predict the reverse ISE. Therefore, the N-G-Fs and N-G-H models should be further modified to accurately predict the reverse ISE.

Background: Colorectal adenoma undergoes neoplastic progression via the normal epithelium-adenoma-adenocarcinoma sequence as reported in the Vogelgram. The risk of developing cancer is strongly associated with the number and size of adenoma and with the subtype. Currently, adenomatous polyps can be distinguished on the basis of histology: the prevalence are tubular, 5-15% are villous and tubular/villous. Considering the increased risk for malignant transformation described for tubular/villous adenomas, patients diagnosed with adenomatous polyposis are at increased risk of developing CRC. The Wnt/β-catenin pathway plays a key role in the onset of colorectal adenoma, in particular intestinal cells first acquire loss-of-function mutations in APC gene that induce the formation of adenomas. Methods: Wnt/β-catenin pathway APC, Wnt3a, Wnt5a, LEF1, BCL9 genes and protein expression analyses were conducted by qRT-PCR and western blot in 68 colonic samples (polyps and adjacent mucosa) from 41 patients, of which 17 affected by FAP. Ten normal colonic mucosal samples were collected from 10 healthy donors. Results: In this study both APC gene and protein resulted less expressed in colon tumor compared to the adjacent colonic mucosa. Conversely, activated β-catenin was more expressed in polyps than in the adjacent mucosa. All results confirmed literature data on carcinomas. A statistically significant correlation between Wnt3a and BCL9 both in polyps and in the adjacent mucosa underlies that the canonical Wnt pathway is activated in early colon carcinogenesis and that the adjacent mucosa is already altered. Conclusion: This is the first study analyzing the difference in expression of Wnt/β-catenin pathway in human colorectal adenomas. Understanding the progression from adenomas to colorectal carcinomas is essential for the development of new therapeutic strategies and improving clinical outcomes.

Objectives. To compare the audiological benefits of a non-implantable wearing option of a bone conduction (BC) implant mounted on an arch (SoundArc) to traditional BC hearing aids (HA) mounted on eyeglasses (BCHA) in patients with moderate to severe conductive or mixed hearing loss. Methods: A preliminary cross-sectional observational prospective cohort study was conducted at a Tertiary Audiological Department, University Hospital. Fourteen adults with conductive or mixed hearing loss (PTA at 0.5-1-2-4 KHz = 67 ± 15 dB HL) had been wearing conventional BCHA on eyeglasses for at least 3 years, and refused the surgical implantation of a BC hearing implant (BCHI). Unaided and aided pure-tone AC and BC thresholds and speech test in quiet and in noise were recorded at baseline and in two different settings: with a BCHI mounted on SoundArc®, and with their own BCHA with two couplers, mounted on eyeglasses. International Inventory for Hearing Aids [IOI – HA], the Hearing Handicap Inventory [HHIA/E], Speech, Spatial, Qualities of Hearing Scale [SSQ], a 10-scores visuo-analogic scale [VAS], and Fatigue impact scale [FIS] score were asked in both conditions. Results: a statistical significative functional gain was observed for both settings. (p=.0001) Better speech perception performances in quiet and in noise were observed with SoundArc compared to their conventional BCHA on eyeglasses (word repetition score in noise improvement of +19.3 at SNR +10 dB, p=.002; + 12.1 at SNR 0 dB, p=.006; and +11.4 at SNR -10 dB, p=.002) No significant differences were found in IOI–HA, FIS, and HHIA/E scores, while significative better SSQ scores in all domains were reported for SoundArc. (p=.0038) Conclusions: Although patients were accustomed to their BCHA on eyeglasses, the non-implanted wearable option of the BCHI proved to be a viable alternative in adult patients with conductive or mixed hearing loss unable to receive or refusing BCHI surgery.

Systematic reviews represent a powerful instrument to summarize the existing evidence in medical literature. However, articles for a systematic review are hard to identify, and mostly require a structured search of the literature through a number of databases, using keyword-based search strategies, followed by the painstaking manual selection of pieces of evidence that are pertinent to the query. A.I. algorithms may offer solutions to reduce the workload on investigators. We applied BERTopic, a newer and much-recognized transformer-based topic-modeling algorithm, to two datasets of 6137 and 5309 articles of newly published systematic reviews in the area of peri-implantitis and bone regeneration in implant dentistry. In the two datasets, BERTopic identified 14 and 22 clusters, respectively, and it automatically created labels describing the nature of the topics for each individual cluster based on semantic interpretation of their titles. Most themes regarded the query theme, but in both conditions, BERTopic also uncovered articles related to off-themes, which composed around 30% of the dataset—with sensitivity up to 0.79 and specificities of at least 0.99. Our results suggest that adding a topic-modeling step to the screening process could potentially save working hours for researchers involved in systematic reviews of the literature.

Localized jawbone invasion is a milestone in the progression of oral squamous cell carcinoma (OSCC). The factors that promote this process are not well understood. Sclerostin is known to be involved in bone metabolism and there are preliminary reports of its involvement in bone tumors and metastasis. To identify a possible involvement of sclerostin in the bone invasion process of OSCC, sclerostin expression was analyzed in vitro in two different human OSCC tumor cell lines by qRT-PCR, and the effect of recombinant human (rh)-sclerostin treatment on tumor cell capabil-ities was evaluated using proliferation, migration, and invasion assays. Undifferentiated human mesenchymal stem cells (hMSCs) were osteogenically differentiated and co-cultured with OSCC tumor cells to demonstrate potential interactions on migration characteristics. Sclerostin expres-sion was evaluated in clinical cases by immunohistochemistry at the OSCC jawbone interface in a cohort of 15 patients. Sclerostin expression was detected in both OSCC tumor cell lines in vitro and was also detected at the OSCC jawbone interface in clinical cases. Tumor cell proliferation rate, migration and invasion ability were increased by rh-sclerostin treatment. The migration rate of tumor cells co-cultured with osteogenically differentiated hMSCs was increased. The re-sults presented are the first data suggesting a possible involvement of sclerostin in the bone inva-sion process of OSCC, which needs to be further investigated

Intermittent religious fasting increases a risk of hypo- and hyperglycemia in individuals with diabetes, but its impact in those without diabetes is poorly investigated. The study aim was to examine the effects of religious Bahá'í fasting (BF) on glycemic control and variability and compare these effects with time-restricted eating (TRE). In a three-arm randomized controlled trial, 16 subjects without diabetes were assigned to a BF, 16:8 TRE or control group. Continuous glucose monitoring and food intake documentation was conducted before and during the 19 days of intervention, and 24-hour mean glucose, glycemic variability indices, and glucotypes were assessed. BF and TRE groups, but not the control group, markedly reduced the daily eating window while maintaining macronutrient composition. Only the BF group decreased caloric intake (-677.8 ± 357.6 kcal, p=0.013), body weight (-1.92 ± 0.95 kg, p=0.011) and BMI (-0.65 ± 0.28 kg, p=0.006). Higher maximum glucose values were observed during BF in the within-group (+1.41 ± 1.04, p=0.039) and between-group comparison (BF vs. Control: p= 0.010 and TRE vs. BF: p= 0.022). However, there were no alterations of 24-hour mean glucose, intra- and inter-day glycemic variability indices, or glucotypes in any group. Proportions of time above and below range (70-180mg/dl) and HbA1c values remained unchanged. BF and TRE do not exhibit negative effects on glycemic control and variability in subjects without diabetes.

Cancer remains one of the main causes of death in the world due to its increasing incidence and treatment difficulties. Although several progresses have been done in this field, innovative approaches are needed to reduce tumor incidence, progression and spreading. In particular, the development of cancer vaccines is currently ongoing like both preventive and therapeutic strategy. This concept is not new, but few vaccines have been approved in oncology. Antigen-based vaccination emerges as a promising strategy, leveraging specific tumor antigens to activate the immune system response. However, challenges persist in finding suitable delivery systems and antigen preparation methods. Exosomes (EXs) are highly heterogeneous bilayered vesicles which carry several molecule types in the extracellular space. The peculiarity is that they may be released from different cells and may be able to induce a direct or indirect stimulation of immune system. In particular, EX-based vaccines may cause anti-tumor immune attack or produce memory cells recognizing cancer antigens and inhibit disease appearance. This review delves into EXs composition, biogenesis, and immune-modulating properties exploring their role as tool for prevention and therapy in solid tumors. Finally, here we describe future research directions to optimize vaccine efficacy and realize the full potential of EX-based cancer immunotherapy.

Background: One challenge in implant dentistry is to reduce marginal bone resorption to avoid long-term esthetic and biological complications. Sub-gingival implant placement has been suggested as a suitable strategy. Methods: 38 healthy patients were enrolled to receive bone level (BL – Control group) or 2 mm sub-crestal (SC - Test group) conical connection, platform-switched implants. An immediate tissue level abutment was used in the Test group by following a One Time Abutment (OTA) restorative procedure. Marginal Bone Modification (MBM) was calcu-latied on standardized radiographs at surgery (T0), loading (T1), and 6 months (T2) and 12 months after loading (T3), and cathegorised in Bone Loss (BL) if the resorption occurred below the implant neck and Bone Remodeling (BR) if above. Pocket probing depth (PPD), Bleeding on probing (BoP) and Plaque Index (PI) were also collected. Results: The mean MBM in the test group after 12 months was 0.61mm, compared to 0.52mm in the control group. However, no BL was observed in the test group, as the MBM completely occurred above the implant neck as BR, whilst in the control group MBM corresponded in total to BL. The average PPD was 2.38mm in the test group and 3.04mm in the control group after 12 months, BoP 50% and 43%, PI 33% and 19.44% respectively. Conclusions: Sub-crestal conical connection, platform-switched implants could be a suitable clinical choice to avoid BL with exposure of the treated implants surfaces.

The aim of this research is to investigate the influence of model height employed in the deep drawing of orthodontic aligner sheets on force transmission and aligner thickness. Forty sheets (Zendura FLX) were thermoformed over four models of varying heights (15, 20, 25, and 30 mm). Normal contact force generated on the facial surface of the upper right central incisor (Tooth 11) was measured using pressure-sensitive films. Aligner thickness around Tooth 11 was measured at five points. A digital caliper and a micro-computed tomography (µ-CT) were employed for thickness measurements. The normal contact force exhibited an uneven distribution across the facial surface of Tooth 11. Model 15 displayed the highest force (88.9±23.2 N), while Model 30 exhibited the lowest (45.7±15.8 N). The force distribution was more favorable for bodily movement with Model 15. Thickness measurements, conducted using a digital caliper and µ-CT, revealed substantial thinning of the aligner after thermoforming. This thinning was most pronounced at the incisal edge (50% of the original thickness) and least at the gingivo-facial part (85%). Additionally, there was a progressive reduction in aligner thickness with increasing model height, which was most significant on the facial tooth surfaces. We conclude that the thermoplastic aligner sheets undergo substantial thinning during the thermoforming process, which becomes more pronounced as the height of the model increases. As a result, there is a decrease in both overall and localized force transmission, which could lead to increased tipping by the aligner and a diminished ability to achieve bodily movement.

Background: Smad4, a critical tumor suppressor gene, plays a significant role in pancreatic biology and tumorigenesis. Genetic background and sex are known to influence phenotypic outcomes, but their impact on pancreatic weight in Smad4-deficient mice remains unclear. This study investigates the impact of Smad4 deficiency on pancreatic weight in F1 mice from diverse Collaborative Cross (CC) lines, focusing on the influence of genetic background and sex. Methods: F1 mice were generated by crossbreeding female CC mice with C57BL/6J-Smad4tm1Mak males. Genotyping confirmed the presence of Smad4 knockout alleles. Mice were housed under standard conditions, euthanized at 80 weeks, and their pancreatic weights were measured, adjusted for body weight, and analyzed for effects of Smad4 deficiency, sex, and genetic background. Results: The overall population of F1 mice showed a slight but non-significant increase in adjusted pancreatic weights in heterozygous knockout mice compared to wild-type mice. Sex-specific analysis revealed no significant difference in males but a significant increase in adjusted pancreatic weights in heterozygous knockout females. Genetic background analysis showed that lines CC018 and CC025 substantially increased adjusted pancreatic weights in heterozygous knockout mice. In contrast, other lines showed no significant difference or varied non-significant changes. The interplay between genetic background and sex further influenced these outcomes. Conclusion: Smad4 deficiency affects pancreatic weight in a manner significantly modulated by genetic background and sex. This study highlights the necessity of considering these factors in genetic research and therapeutic development, demonstrating the value of the Collaborative cross-mouse population in dissecting complex genetic interactions.

Enhancement of orthodontic tooth movement (OTM) through local administration of biofunctional molecules has become increasingly significant, particularly for adult patients seeking aesthetic and functional improvements. This comprehensive systematic review analyzes the efficacy of various biofunctional molecules in modulating OTM, focusing on the method of administration and its feasibility, especially considering the potential for topical application. A search across multiple databases yielded 36 original articles of experimental human and animal OTM models, which examined biofunctional molecules capable of interfering with the biochemical reactions that cause tooth movement during orthodontic therapy, accelerating the OTM rate through their influence on the bone metabolism (Calcitriol, Prostaglandins, Recombinant human Relaxin, RANKL and RANKL expression plasmid, growth factors, PTH, osteocalcin, vitamin C and E, biocompatible reduced graphene oxide, exogenous thyroxine, sclerostin protein, a specific EP4 agonist (ONO-AE1-329), carrageenan and herbal extracts). The results indicated a variable efficacy in accelerating OTM, with Calcitriol, Prostaglandins (PGE1 and PGE2), RANKL, growth factors and PTH, among others, showing promising outcomes. PGE1, PGE2 and Calcitriol experiments had statistically significant outcomes in both human and animal studies, and, while other molecules underwent only animal testing, they could be validated in the future for human use. Notably, only one of the animal studies explored topical administration, which also suggests a future research direction. This review concluded that while certain biofunctional molecules demonstrated potential for OTM enhancement, the evidence is not definitive. The development of suitable topical formulations for human use could offer a patient-friendly alternative to injections, emphasizing comfort and cost-effectiveness. Future research should focus on overcoming current methodological limitations and advancing translational research to confirm these biomolecules' efficacy and safety in clinical orthodontic practice.

Sinonasal carcinomas are aggressive neoplasms that present a high morbidity and mortality rate with unfavorable prognosis. This group of tumors exhibits morphological and genetic diversity. Genetic and epigenetic alterations in these neoplasms are currently targets for diagnosis and treatment. The most common type of cancer originated in the sinonasal tract are sinonasal squa-mous cell carcinomas (SNSCC), which presents different histological patterns and variable his-tological aggressiveness. A significant number of alterations have been reported in sinonasal tu-mors, including deficiencies in the SwItch/Sucrose non-fermentable (SWI/SNF) chromatin remod-eling complex. In the sinonasal tract, deficiencies of the subunits SMARCB1/INI1, SMAR-CA4/BRG1 and SMARCA2 have been noted in carcinomas, adenocarcinomas, and soft tissue tu-mors with distinctive high-grade morphology and fatal prognosis. Objective: To identify the status of the SWI/SNF complex using immunohistochemistry in sinonasal squamous cell carci-nomas and its association with morphology and survival. Methods: A total of 1582 SNSCC cases were analyzed, selecting those with high-grade malignancy morphology, which were then evalu-ated immunohistochemically for SMARCB1 and SMARCA4 proteins. Their expression was compared with the biological behavior and survival of the patients. Results: Among the SNSCC, 47% corresponded to the non-keratinizing squamous cell carcinoma (NKSCC) type with high-grade characteristics, 40% were keratinizing squamous cell carcinomas (KSCC), 9% were SMARCB1-deficient carcinomas, and 4% were SMARCA4-deficient carcinomas. Mosaic expres-sion for SMARCB1 (NKSCC 33%, KSCC 21.9%) and SMARCA4 (NKSCC 14.6%, KSCC 12.2%) was identified, showing an impact on tumor size and progression. Conclusions: We identified that the mosaic expression of INI1 in NKSCC exhibited a worse prognosis compared to intact carcinomas and was similar to SMARCB1-deficent carcinoma.

After surgery, oral cavity healing occurs in a hostile environment and requires proper oral care and hygiene to accelerate recovery. The aim of the current study is to investigate and compare the bioreactivity characteristics of chlorhexidine based (CHX) mouth rinse and a novel bone bioactive liquid (BBL) mouth rinse on oral healing within seven days application post-surgery. A randomized, double blind clinical trial conducted in 81 patients. The mouth rinses were applied twice a day for a period of 7 days. The visual analog scale (VAS) protocol was applied to measure pain index. Early wound healing score (EHI) was determined in evaluate the oral cavity healing progress. No adverse effects were observed using the mouth washes, but CHX resulted in teeth staining. CHX and BBL were sufficient to reduce pain over a period of 7 days. However, the BBL group demonstrated a statistically significant reduction in VAS stating day 4. Relative to CHX group, the EHI scores were significantly higher in the BBL group, independent from the tooth location. No gender differences were observed in both VAS and EHI scores. Relative to the commercially available CHX, BBL mouth rinse reduced pain and accelerated oral cavity healing. Suggesting an improvements of oral cavity microenvironment at the wound site that mediates soft tissue regeneration.

Abstract Aim: Micro-invasive therapeutic approaches in endodontics differentiate between different modified types of access cavities: occlusal via a smaller occlusal opening (15 ° access angle), medial (via the caries defect) for premolars and molars (30 ° access angle) and cervical with wedge-shaped defects or root caries on anterior teeth and single-rooted premolars (45 ° access angle). Therefore, the aim of this work was (i) to create an in-vitro model for the clinical simulation of these three different modified access types, (ii) to assess the biomechanics of the instrumentation and (iii) to measure the volumetric substance loss of four different preparation systems. Material and Method: Simulated S-shaped root canals with a high degree of obliteration (ISO 10) in acrylic polymer bodies with canal entrance angles of 15 °, 30 ° and 45 ° were shaped with NaOCl (3%) irrigation under clinical simulation at body temperature (37 ° C) in randomized blinded sequences (n = 7) according to manufacturer's instructions: 1. Conventional geometry, not heat treated, up to 35 / .04 (F360, Komet) 2. Conventional geometry, heat-treated, spark-eroded up to 40 / .04 (Hyflex EDM, Coltene Hyflex) 3. Spiral geometry, heat treated, up to 36 / .03 (TruNatomy, DentsplySirona) 4. Distinctive spiral geometry, heat-treated (XP-Endo Shaper, FKG) The vectorization (AutoCAD) of the root canals was performed before and after preparation in the apical, middle and coronal third of the root canal. The volumetric loss of substance in cubic millimeters was recorded and statistically evaluated using an independent two-sided t-test. Clinical demonstrations include three cases of micro-invasive access cavities as final proof of principle of fast and safe root canal treatment. Results The total loss of volume at 15 ° entry angles is significantly lowest with TruNatomy and XP Endo. With an access angle of 30 °, the total loss remains low and increases with F360 and Hyflex .. At a 45 ° access angle, the group differences remain: TruNatomy (6.5 mm3) and XP Endo (6.4 mm3) versus F360 (8.3 mm3) and Hyflex (8.4 mm3). This difference in loss of simulated root dentin is highly significant. Conclusions Conventional instruments achieve optimal shape of apical third of root canals at all entrance angles only with higher substance loss in coronal and middle thirds . In contrast, the spiral instrument geometry contributes to dentin protection and supports the concept of minimally invasive endodontics for lifelong tooth preservation as shown in four clinical cases.

Increasing evidence suggests that prenatal exposure to opioids can adversely influence brain development, yet, limited data exists on the effects of opioid-exposure on preschool language development. Our study aimed to characterize the nature and prevalence of language problems in children prenatally exposed to opioids, and the factors that support or hinder language acquisition. A sample of 100 children born to pregnant women in methadone maintenance treatment and 110 randomly identified non-exposed children were studied from birth to age 4.5 years. At 4.5 years, 89 opioid-exposed and 103 non-exposed children completed the preschool version of the Clinical Evaluation of Language Fundamentals (CELF-P) as part of a comprehensive neurodevelopmental assessment. Children prenatally exposed to opioid had poorer receptive and expressive language outcomes at age 4.5 years compared to non-exposed children. After adjustment for child sex, maternal education, other pregnancy substance use, maternal pregnancy nutrition and prenatal depression, opioid exposure remained a significant independent predictor of children’s total CELF-P language score. Examination of a range of potential intervening factors showed that a composite measure of the quality of parenting and home environment at 18 months and early childhood education participation at 4.5 years were important positive mediators.

(1) Background: Tooth extraction is one of the oldest and most well-known surgical procedures in dental medicine. It is still routinely performed to date by both general practitioners, oral surgeons, and dental undergraduates. The Benex extraction system allows for the extraction of teeth in vertical direction, which avoids most trauma against the surrounding alveolar bone and soft tissues; (2) Methods: The study included 56 patients who were recruited from the department of Oral Surgery at the Faculty of Dental Medicine, Medical University – Plovdiv. Patients were divided into two groups of 28 patients – Group I (control group) and Group II (study group). For each group the success of the extraction, buccal cortical plate preservation, pain experience and early wound healing were assessed; (3) Results: There was no statistical significance between the success of the extractions in both groups. The Benex extractions preserved the buccal cortical plate in 95% of the cases, whereas the forceps extractions only in 71.8%, which shows a statistical significance. On the seventh day patients in group II reported less pain, without a significant difference. There was a significantly bigger number of completely healed extraction wounds on the 10th day; (4) Conclusions: Atraumatic extractions allow for more hard and soft tissues to be preserved in the extraction site. This is all crucial for the successful outcome and aesthetically pleasing results of a following prosthetic or implant restoration.

Severe early childhood caries remains the most common chronic disease affecting children. Its multifactorial etiology has established a controversy about which risk factors were more significant to its development. Therefore our study aimed through meticulous statistical analysis to arrange the “well agreed upon” common risk factors in order of significance, to aid the clinician in tailoring an adequate preventive program for this affected age group. The study reshuffled the risk factors contributing to severe early childhood caries and placed them in the order of their significance as follows: snacking of sugary food several times a day, increased number of siblings to 3 or more, night feeding, child self-employed brushing, mother caries experience, 2 siblings, on demand feeding, once/day sugary food, sharing utensils, 1 Sibling, male gender, father’s education, late first child dental visit, brushing time, mother’s education, no dental visit, decreased brushing frequency & no night brushing.

In this study, a novel oral formulation of berberine hydrochloride (BBH) hydrogel was successfully synthesized through physical cross-linking using chitosan (CS) and carboxymethyl-β-cyclodextrin (CMCD). The characterization results confirmed the successful synthesis of CS/CMCD hydrogel and the subsequent loading of BBH into this composite (CS/CMCD/BBH) was effectively accomplished. BBH was used as a model drug and the resulting hydrogel demonstrated a sustained drug release profile. In addition to its improved solubility and sustained release characteristics, the hydrogel exhibited excellent antibacterial activity against common pathogens such as Escherichia coli (E. coli), Staphylococcus aureus (S. aureus), and Candida albicans (C. albicans). Additionally, in vitro studies indicated that the hydrogel was not cytotoxic to NIH3T3 and HaCaT cells, suggesting its safety for biomedical applications. This lack of cytotoxic effects, combined with the mechanical strength, solubility improvements, and antibacterial properties of the hydrogel, positions the CS/CMCD/BBH hydrogel as a promising candidate for effective oral delivery of BBH. By addressing the solubility and delivery challenges of BBH, this hydrogel offers a viable solution for the oral administration of berberine hydrochloride, with potential applications in various biomedical fields.

Cadaver bone is possibly the most common transplant material used today. Common types of cadaver bone transplants are freeze dried bone allografts and xenografts. In the case of freeze dried bone allograft transplants, it was theorized that these materials mineralize by way of osteoinduction and stimulating osteogenesis. However, these theories have been proven false. It has been proposed that these materials mineralize via osteoconduction however, there are no studies to support this hypothesis. This study was undertaken to determine how these transplants mineralize and what type of bone they produce. Materials and Methods: This study is a histological analysis of human cadaver bone graft healing from the incipient stages of mineralization through completed mineralization. All cadaver bone grafts used for evaluation in this study were particulate bone graft materials in the maxilla or mandible. No block grafts were evaluated. Results: The mineralization of cadaver bone transplants was produced by an inflammatory response to the transplanted tissue. The histologic findings of the mineralized bone produced by this process was sclerotic bone. No resorption of cadaver bone graft particles was found. When loaded the sclerotic bone was found to fail through an accumulation of microfractures.Conclusions: Particulate freeze-dried bone allografts and xenografts do not heal via the normal processes of mineralization. Cadaver bone grafts produce significant inflammation and are hypothesized to mineralize by a process termed antigenic ossification. The process of antigenic ossification produces sclerotic bone that is not capable of self-repair which can ultimately lead to bone failure.

Background:The association between ABO and Rh blood groups and diseases is an intriguing topic that continues to be studied. However, how mandibular symmetry may vary by blood group has not been investigated. This study explored the relationship between these blood groups and mandibular condyle and ramal asymmetries in the Turkish adult population. Methods:The study included 149 adult patients (67 males and 82 females) without systemic diseases or temporomandibular disorder complaints. Asymmetry was assessed in panoramic radiographic images using a formula developed in a previous study. The chi-square and Kruskal-Wallis tests were used to analyze differences among ABO groups while the Mann-Whitney U test was used for Rh groups. Results:There were no statistically significant differences among the ABO blood groups, nor the Rh groups, in terms of sex, Rh factor, and age distribution. However, a comparison of the ABO and Rh blood groups revealed that condylar asymmetries were significantly more common in the AB group. Conclusions:These results suggest that mandibular asymmetry may be associated with the ABO blood group. These findings may guide future research to gain a deeper understanding of the relationship between mandibular asymmetry and blood groups.

Cartilage degeneration is a characteristic of osteoarthritis (OA) which is often observed in aging populations. This degeneration is due to the breakdown of articular cartilage (AC) mechanical and tribological properties, primarily attributed to lubrication failure. Understanding the reasons behind these failures and identifying potential solutions could have significant economic and societal implications, ultimately enhancing the quality of life. This review provides an overview of developments in the field of AC, focusing on its mechanical and tribological properties. The emphasis is on the role of lubrication in degraded AC, offering insights into its structure and function relationship. Further it explores the fundamental connection between AC mechano-tribological properties and the advancement of its degradation and puts forth recommendations for strategies to boost its lubrication efficiency.

Objective: To determine the effect of sandblasting before and after sintering on the surface roughness of zirconia and the micro-tensile bond strength of a pressable veneering ceramic to zirconia. Methods: Pre-sintered zirconia blocks (IPS e.max ZirCAD, Ivoclar Vivadent) were divided into a control group (CTR, no surface treatment) and four test groups of three specimens each: Pre-S-30, Pre-S-50, Pre-S-110 were sandblasted with 30µm SiO2, 50µm Al2O3 and 110µm Al2O3 particles respectively, before sintering, Post-S-30 was sandblasted with 30µm SiO2 after sintering. For each treatment, the surface roughness was measured (Ra, Perthometer M4P, Mahr Perthen). After sintering the zirconia blocks, a liner and a pressable ceramic (IPS e.max ZirPress, Ivoclar Vivadent) were fired. Sixteen micro-bars were obtained from each block and submitted to the micro-tensile bond strength (µTBS) test. Data were analyzed with one-way ANOVA. Any correlation between Ra and µTBS was evaluated (Sperman test). Results: Sandblasting before sintering with 110µm Al2O3 (Ra=3.44±0.44µm), 50µm Al2O3 (Ra=2.32±0.46µm), and 30µm SiO2 (Ra=1.22±0.22µm) resulted in significantly higher roughness than sandblasting after sintering with 30µm SiO2 (Ra=0.46±0.11µm). The highest µTBS was measured when the sintered zirconia was sandblasted with 30μm SiO2 (26.79±14.80 MPa), which was significantly different from that of specimens that were sandblasted before sintering (Pre-S-30=20.90±11.70; Pre-S-50=21.27±15.19; Pre-S-110=23.99±16.83) or were not treated (CTR=17.44±14.03). Conclusions: Sandblasting zirconia before sintering enhances the surface roughness proportionally to the particle size of the sand used. Sandblasting with 30µm SiO2 after sintering appeared to improve bonding between the veneering ceramic and zirconia. Clinical Significance: Sandblasting with 30µm SiO2 after sintering may improve bonding between veneering ceramics and zirconia, thus reducing ceramic fractures/chippings.

This study investigated the efficacy and safety of a propolis mangosteen extract complex (PMEC) on gingival health in patients with gingivitis and incipient periodontitis. A multi-centered randomized, double-blind, placebo-controlled trial involving 104 subjects receiving either PMEC or placebo for eight weeks was conducted. The primary focus was on changes in inflammatory biomarkers from gingival crevicular fluid (GCF), with clinical parameters as secondary outcomes. Results revealed that the PMEC group showed significantly reduced expression of all measured GCF biomarkers compared to the placebo group (p&lt;0.0001) at 8 weeks, including substantial reductions in IL-1β, PGE2, MMP-8, and MMP-9 levels compared to baseline. While clinical parameters trended towards improvement in both groups, inter-group differences were not statistically significant. No significant adverse events were reported, indicating a favorable safety profile. These findings suggest that PMEC consumption can attenuate gingival inflammation and mitigate periodontal tissue destruction by modulating key inflammatory mediators in gingival tissue. Although PMEC shows promise as a potential adjunctive therapy for supporting gingival health, the discrepancy between biomarker improvements and clinical outcomes warrants further investigation to fully elucidate its therapeutic potential in periodontal health management.

The current treatment for cervico-facial cancer involves radio and/or chemotherapy. Unfortunately, cancer therapies can lead to local and systemic complications such as mucositis, which is the most common dose-dependent complication in the oral cavity and gastrointestinal tract. Mucositis can cause a considerably reduced quality of life in cancer patients already suffering from physical and psychological exhaustion. However, melatonin, whose role in the treatment of mucositis has recently been investigated, offers an effective alternative therapy in the prevention and/or management of radio and/or chemotherapy-induced mucositis. This review focuses on the pathobiology and management of mucositis in order to improve the quality of cancer patients’ lives.

The oral mucosa represents a defense between the external environment and the rest of the body and encompasses several antimicrobial and antiviral mechanisms. Oral mucosal cells are constantly bathed in hypotonic saliva (normally one-third tonicity compared to plasma) and are repeatedly exposed to environmental stresses of tonicity, temperature and pH by the drinks we imbibe (e.g. hypotonic: water, tea, coffee; hypertonic: assorted fruit juices, red wines), as well as of diverse microbial and viral flora. In the mouth, the broad-spectrum antiviral mediator MxA (a dynamin-family large GTPase) is constitutively expressed in healthy periodontal tissues, and also induced by Type III interferons (e.g. IFN-λ1). Endogenously induced human MxA and exogenously expressed human GFP-MxA formed membraneless biomolecular condensates in the cytoplasm of oral carcinoma cells (OECM1 cell line). These condensates likely represent storage granules in equilibrium with antivirally active dispersed MxA. Remarkably, cytoplasmic MxA condensates were exquisitely sensitive sensors of hypotonicity – the condensates in oral epithelium disassembled within 1-2 min of exposure of cells to saliva-like one-third hypotonicity, and spontaneously reassembled in the next 4-7 min. OECM1 cells preloaded with calcein-AM (a reporter of cytosolic “macromolecular crowding”) confirmed unquenching and then requenching of calcein fluorescence during this process. Hypertonicity had little effect on MxA condensates. The spontaneous reassembly of GFP-MxA condensates in oral epithelial cells even under continuous saliva-like hypotonicity was slowed by the protein phosphatase inhibitor cyclosporin A (CsA) and by the K-channel blocker tetraethylammonium chloride (TEA) suggestive of the involvement of the volume-sensitive WNK kinase-protein phosphatase (PTP)-K-Cl cotransporter (KCC) pathway in the regulated volume decrease (RVD) during condensate reassembly in oral cells. Thus, physiologically, hypotonic drinks (water, tea, coffee) trigger a rapid deployment of antiviral MxA throughout the cytoplasm of oral epithelial cells, with subsequent salvage of MxA back into storage granules/condensates.

Electrospinning is the versatile technique to generate large quantities of micro- or nano-fibers from a wide variety of shapes and sizes of polymer. Natural bone is a hierarchically composites with the dispersion of inorganic ceramic along organic polymer. The aim of this study, the electrospun poly (lactic acid) (PLA) mats coated with chitosan (CH) and calcium silicate (CS) powder were fabricated. The morphology, chemical composition, and surface properties of CS/CH-PLA composites were characterized by scanning electron microscopy, X-ray diffraction, and Fourier transform infrared spectroscopy. In vitro, the CS/CH-coated PLA mats increased the formation of apatite on the surface when soaking in cell cultured medium. During culture, the adhesion and proliferation of the human mesenchymal stem cells (hMSCs) cultured on CS/CH-PLA were significantly promoted relative to those on PLA. Collagen I and fibronectin levels and promoted cell adhesion were observed upon an increase in CS content. Further, compared to PLA mats without CS/CH, CS10 and CS15 mats markedly enhanced the proliferation of hMSCs as well as their osteogenesis properties, which was characterized by bone-related gene expression. Our results demonstrated that the biodegradable and electroactive CS/CH-PLA mats had potential application as an ideal candidate for bone tissue engineering. Together, findings from this study clearly demonstrated that PLLA-C2S composite scaffold may function as an ideal candidate for bone tissue engineering.

Background: The absence of interdental papillae in dental prosthetics often results in unsatisfactory esthetic outcomes, such as black triangles and elongated clinical crowns. Although previous research has shown that gingival papillae can regenerate in a coronal direction, the mechanisms behind this phenomenon are not fully understood. Various theories have been proposed as potential explanations. Materials and Methods: This study evaluated several factors potentially influencing papilla growth, including adjacent elements, buc-cal-lingual papilla width, contact point position, convergent neck, crown overcontour, and intraoral negative pressure. A conceptual map was created to organize these factors, followed by their classification using a modified Overton Window. The principle of parsimony (Occam's Razor) was applied to identify the most plausible cause-related factors, categorizing them as causal relationship factors, filtered out factors, essential factors, or influencing factors. A mind map was used for visual grouping. Results: The analysis identified intraoral negative pressure as the most plausible cause-related factor for spontaneous papilla growth. Factors such as inflammation and drug-induced hyperplasia were excluded due to their association with unhealthy tissue. Other factors were classified as essential or influencing, but without direct causal links to papilla growth. Conclusions: Intraoral negative pressure is likely a key contributor to spontaneous papilla growth around implants. This finding, supported by abductive reasoning and the exclusion of less plausible factors, offers a new direction for enhancing esthetic outcomes in dental prosthetics, though further research is needed to confirm this causal relationship.

This work explores the significance of toothbrushing in maintaining optimal oral health, delving into its benefits, proper techniques, and types of toothbrushes. The primary cause of caries, periodontal diseases, and halitosis is oral biofilm development. One of the most fundamental practices in maintaining oral health is toothbrushing. Studies have confirmed that mechanical procedures for controlling plaque and toothbrushing, in particular, significantly decrease plaque accumulation. The significance of teeth brushing in preventing dental caries has been well-acknowledged for a considerable period. Dentists recommend brushing twice daily for at least two min to ensure thorough cleaning. Unfortunately, precise guidelines from dental associations are often missing. Authors mention that two min of brushing are insufficient for significant plaque removal; plaque removal increases with augmented brushing time, with maximum removal at 180 s. Multiple studies have documented that engaging in the practice of brushing one’s teeth twice a day has a preventive impact. Various toothbrush designs, including both manual and electric options, have been created to improve the elimination of dental biofilm and reduce the accumulation and persistence of bacteria. In conclusion, toothbrushing is a simple yet incredibly important practice for maintaining oral health. The benefits extend beyond just a bright smile, encompassing caries, gum disease, halitosis prevention, and the preservation of tooth enamel. Adhering to proper toothbrushing techniques, selecting the right toothbrush, and understanding the connection between oral health and overall well-being can lead to a healthier life. To foster favorable toothbrushing behaviors among the population, dental practitioners and public health experts must know the factors that influence toothbrushing habits.

Background: Snus consumption is increasingly popular, mainly among the youth, due to the promotion of the tobacco industry and the lack of knowledge regarding its adverse effects. Even though some of its systemic complications are common knowledge, the oral consequences are rarely known. Aim: Therefore, the objective of this study is to evaluate the oral health effects of snus consumption among a highly exposed group of adolescent athletes. Design: Participants received an interactive presentation, followed by interviews and dental screenings by young doctors to establish trust. They were categorized into groups based on the frequency of snus usage. The oral hygiene habits and status, snus consumption habits and awareness about its adverse effects were evaluated. Results: Statistically significantly (p

Stage IV grade C localized periodontitis (pre-puberal localized aggressive periodontitis/LPP), an extremely rare form of periodontal disease, occurs in otherwise healthy individuals (no signs of dental plaque/calculus) due a hyper-aggressive auto-immune response to high periodontopathic bacteria levels. Methods: A 4-year-old Caucasian girl with unusual high mobility of temporary lower left canine and localized gingival inflammation was misrecognized by multiple clinicians (initially diagnosed with hypophosphatasia, genetic and metabolic disorders, all turning negative), over a period of 4-6 month, despite initial radiographs showing clear pathognomonic signs. LPP diagnostic was made by the last clinician, but by now the tooth was lost. Similar inflammation signs appeared around the lower temporary right canine. X-ray examination showed similar bone and periodontal loss as previously seen, while periodontopathic bacteria tested highly positive. The patient received both mechanical cleaning and ten days systemic antibiotic treatment (Augmentin and Metronidazole). Results: Two months after, inflammation signs disappeared, with periodontal regeneration radiologically present, and only small periodontopathic bacteria precursors concentrations. Conclusions: Despite initial periodontal loss, an adequate treatment can keep under control an LPP disease. Moreover, bone and periodontal regeneration appears if periodontopathic bacteria scores are kept lower, showing the importance of fast adequate diagnostic and treatment.

Resection of malignant lesions in the oral and maxillofacial area causes functional and morphological defects. To recover from these defects, reconstruction surgery is needed such as a primary closure or a flap. There are advantages and disadvantages to the method of using the primary closure and the flap, and the choice of procedure is entirely up to a surgeon. The purpose of this study is to evaluate availability of primary closure in patients. For 10 years from January 2010 to May 2020, patients who recovered using flaps after removing malignant lesions from the oral cavity and those who closed the lesion using primary closure were investigated. The investigation was conducted by searching the database of the hospital. There were 85 patients who removed malignant lesions in the oral and maxillofacial area, and among them 16 patients closed the soft tissue defects using primary closure. Operation time, histologic types, stages, wound status, and period of hospitalization according to the patients' medical records were investigated retrospectively. Between the staging and the primary closure, statistically significant differences were observed between stage I and stage II patients in 13 patients using the primary closure. (P=0.046). Statistically significant differences were identified between operation time and primary closure, with an average of 4.02 hours (P=0.015). The average period of hospitality for patients who underwent primary closure was 13.4 days, compared to 26.7 days for those who underwent flap surgery. This difference was statistically significant (P=0.0003). This study evaluated the use of primary closure in patients who underwent resection of malignant lesions in the oral and maxillofacial area. Although the majority of patients underwent reconstruction with flaps, our results showed that primary closure can be a viable option for certain patients with early-stage lesions. Therefore, oral and maxillofacial surgeons should carefully consider various evaluation criteria and select appropriate reconstruction methods to optimize functional and aesthetic outcomes for each patient.

Alzheimer’s disease (AD) and the therapies of AD with anti-amyloid1-42 (Aβ) monoclonal antibodies are associated with the vascular complications of brain edema, hemorrhage, and cerebral amyloid angiopathy (CAA) termed amyloid-related imaging abnormalities (ARIAs). The neuropathology of normal and AD brains demonstrates that monocyte/macrophages (MMs) are critical in successful brain clearance in healthy brain by up-loading, transporting, and degrading Aβ but fail degradation and clearance in AD patients by releasing Aβ into vessels at the blood-brain barrier, causing vasculitis and ARIAs. The naturally-formed epoxides (EpFAs) of polyunsaturated fatty acids (PUFA’s), including arachidonic, docosahexaenoic, and eicosapentaenoic fatty acids, may repair degradation of Aβ by regulating Aβ-degrading enzymes, inflammatory cytokines, and unfolded protein response (UPR) to endoplasmic reticulum stress in a homeostatic fashion. EpFAs are, however, degraded by the soluble epoxide hydrolase enzyme (sEH) but are protected by the sEH inhibitor (sEHI) TPPU. In the cultures of AD patients’ macrophages, TPPU with the epoxide EEQ, and the cGAS/STING inhibitor H-151 increased uptake of Aβ at 2 hours and degradation of Aβ at 24 hours. In conclusion, the soluble epoxide hydrolase inhibitor TPPU with omega-3 fatty acids and the cGAS/STING inhibitor H-151 increase Aβ uptake and degradation in macrophages of AD patients, and potentially enhancing Aβ clearance in the AD brain.

The human oral microbiome refers to an ecological community of symbiotic and pathogenic microorganisms found in the oral cavity. The oral cavity is a suitable environment that provides various kinds of biological niches such as teeth, tongue, and oral mucosa. The oral cavity is the gateway between the external environment and the human body, maintaining oral homeostasis, protecting the mouth, and preventing disease. On the flip side, the oral microbiome plays an important role in triggering, development, and progression of oral and systemic diseases. Currently, disease diagnosis through the analysis of the human oral microbiome has been realized with the recent development of innovative detection technology, and is overwhelmingly promising compared to the previous era. It has been found that patients with oral diseases and systemic diseases have variations in the oral microbiome compared to normal subjects. This narrative review provides insight into the pathophysiological role that oral microbiome plays in influencing oral and systemic diseases, and updates the knowledge related to the oral microbiome over the past 30 years. A wide range of updates was provided with the latest knowledge of the oral microbiome to help researchers and clinicians in both academic and clinical aspects. The microbial community information can be utilized in non-invasive diagnosis and help develop a new paradigm in precision medicine, which will benefit human health in the era of post-metagenomics.

Octacalcium phosphate (OCP) is a precursor of biological apatite crystals that has attracted attention as a possible bone substitute. On the other hand, few studies have examined this material at the experimental level due to the limitations of OCP mass production. Recently, mass production technology of OCP was developed, and the launch of OCP bone substitutes is occurring. In this study, the bone regeneration capacity of OCP products was compared with two of the most clinically used materials: heat-treated bovine bone (BHA) and sintered biphasic calcium phosphate (BCP). Twelve rabbits were used, and defects in each tibia were filled with OCP, BHA, BCP, and left unfilled as control (CON). The tibias were harvested at 4 and 12 weeks, and 15 μm slides were prepared using the diamond grinding method after being embedded in resin. Histological and histomorphometric analyses were performed to evaluate the bone regeneration ability and mechanism. The OCP showed significantly higher resorption and new bone formation in both periods analysed (p<0.05). Overall, OCP bone substitutes can enhance bone regeneration significantly by activating osteoblasts and a rapid phase transition of OCP crystals to biological apatite crystals (mineralisation), as well as providing additional space for new bone formation by rapid resorption.

Incidental findings (IFs) depicted in imaging tests during diagnostic evaluation of patients with cleft lip and/or palate (CL/P) can guide clinicians during treatment-planning procedures for effective, comprehensive cleft care. Evidence regarding IFs in different anatomical regions distant from the dentition are scarce. The aim of this study was to compare the prevalence of IFs in various anatomical areas between patients with non-syndromic CL/P and unaffected subjects. Orthopantomographs (OPT), lateral cephalometric (LC) radiographs and cone-beam computed tomography (CBCT) scans of 120 subjects (case group: n = 40, 18 females, age 14.5 ± 5.0 years; control group: n = 80, 36 females, age 14.6 ± 4.9 years) were examined and IFs were assessed by four observers. Significantly higher prevalence of IFs (p &lt; 0.001) was reported in the case group (97.5%) compared with the control group (62.5%). The most prevalent location of IFs in the case group was the maxilla (92.5%), followed by the nasal cavity (75.8%) and the mandible (63.2%), while in the control group, the highest rates of IFs occurred in the maxilla (43.8%), mandible (41.3%) and temporomandibular joint (TMJ) (14.7%). No gender-dependent pattern for IF occurrence was detected overall. Orofacial clefts may affect the mandible. However, the reported IFs were limited compared to those in the maxilla. In conclusion, individuals with CL/P are more likely to present with a range of IFs than their unaffected peers. Understanding the association between CL/P and IFs is critical for successful interdisciplinary treatment, raising awareness of the potential need for future dental care for cleft patients, and managing extra-dental aberrations. A systematic assessment of diagnostic records is required to eliminate the risk of overlooking clinically significant IFs.

Can the type of implant rehabilitation influence peri-implant bone loss in case of full-arch mandibular prosthesis? The purpose of the study was to assess, by orthopantomograms (OPG), bone loss around implants in different types of implant-supported prosthetic rehabilitations and evaluate potential risk factors associated with the number and location of implants that may have an association with bone defect. A radiographic study was conducted on 22317 OPGs in the time range from 2010 to 2024. All OPGs with implant-supported prosthetic mandibular rehabilitations were included in the study. A total of 155 OPGs were evaluated, with peri-implant bone loss identified in 64 (41.3%). Distal implants (furthest from the center) across various positioning patterns were most susceptible to bone loss, with positions 3.6 and 4.6 demonstrating the most frequent occurrences (25 and 26 cases, respectively). χ² test revealed significant associations between both implant positioning pattern (p &lt; 0.001) and number of implants (p &lt; 0.001) with peri-implant bone loss. Also by updating the sample of OPGs, increased susceptibility to bone resorption was found for implants placed distal to the mental foramen compared to mesial ones in full-arch implant-supported fixed prostheses. Prospective clinical studies will then be useful to investigate this finding further.

Percutaneous vertebroplasty procedure is of major importance, given the significant increasing aging population and higher number of orthopedic procedures related to vertebral compression fractures. Vertebroplasty is a complex technique involving injection of polymethylmethacrylate (PMMA) into the compressed vertebral body for mechanical stabilization of the fracture. Our understanding and ability to modify these mechanisms through alterations in cement material is rapidly evolving. However, the rate of cardiac complications secondary to PMMA injection and subsequent cement leakage has increased with time. The following review considers the main features of PMMA bone cement on the heart, and the extent of influence of materials on cardiac embolism. Clinically, cement leakage results in life-threatening cardiac injury. The convolution of this outcome through an appropriate balance of complex material properties is highlighted via clinical case report.

Background Patients with severe dysphagia are usually fed using a nasogastric tube (NGT). Many patients who receive long-term NGT feeding are unable to obtain sufficient nutrients orally immediately after NGT removal. Thus, a transitional period involving oral diet training is required to transition from NGT feeding to exclusive oral feeding. We aimed to investigate the therapeutic effect of oral diet training in indwelling NGT patients with prolonged dysphagia. Methods A total of 175 patients who were fed using an NGT for more than 4 weeks were enrolled. Their swallowing function was evaluated by a videofluoroscopic swallowing study (VFSS). During the VFSS, patients received thick and thin barium while the NGT was insulted. Then, the patients underwent a VFSS without an NGT thirty minutes after NGT removal. If a patient had no aspiration with NGT inserted during the VFSS, oral diet training combined with NGT feeding was recommended. Results Of the 49 indwelling NGT patients who were recommended to receive oral diet training, 39 (79.6%) transitioned to exclusive oral feeding. A transition period of 2-8 weeks was required for them to achieve full oral feeding. Patients who were eligible for oral feeding trials showed no significant aspiration during the VFSS with an NGT inserted and had sufficient cough function. Patients who required prolonged NGT feeding and who could not complete oral trials showed significant aspiration during the VFSS when an NGT was inserted. Conclusion This study demonstrated that oral diet training combined with NGT feeding was safe in patients with prolonged dysphagia who had sufficient cough function and no aspiration during VFSS. We suggest that if the patient is a proper candidate for NGT removal, direct oral feeding training with an NGT inserted could be a useful therapeutic strategy during the transitional period from long-term NGT feeding to successful oral feeding.

Oral squamous cell carcinoma (OSCC) is a highly prevalent and aggressive malignancy, with mortality rates that reach 60%, mainly due to an excessive diagnostic delay. MiRNAs, a class of crucial epigenetic gene-expression regulators, have emerged as potential diagnostic biomarkers, with >200 molecules reported to be dysregulated in OSCC. We had previously established an in silico methodology for the identification of the most disease-specific molecules by bridging genetics and epigenetics. Here, we identified the stage-specific miRNAs that govern the asymptomatic early stages of oral tumorigenesis by exploiting the reverse interplay between miRNA-levels and their target-genes’ expression. Incorporating gene expression data from our group’s experimental hamster model of sequential oral oncogenesis, we bioinformatically detected the miRNAs that simultaneously target/regulate >75% of the genes that are characteristically upregulated or downregulated in the consecutive stages of hyperplasia, dysplasia and early-invasion OSCC, while exhibiting the opposite expressional dysregulation in OSCC-derived tissue and/or saliva specimens. We found that all stages share the downregulation of miR-34a-5p, miR124-3p, and miR-125b-5p, while miR-1-3p is underexpressed in dysplasia and early-invasion. Malignant early-invasion stage is distinguished by the downregulation of miR-147a and the overexpression of miR-155-5p, miR-423-3p and miR-34a-5p. The identification of stage-specific miRNA molecules may facilitate their utilization as biomarkers for presymptomatic OSCC diagnosis.

This critical review revisited the new classification system for periodontitis, specifically for staging, suggesting modifications, and introducing a new flowchart for a better clinical evaluation. It evaluated articles published between 2018 and 2024 in the English language, which had an educational motivation focused on staging periodontitis. PubMed/MEDLINE, Web of Science, and Embase databases were used to retrieve the articles. The focus questions involved the analysis of all parameters for staging periodontitis. A total of 836 articles were initially found; 388 duplicated were excluded; 448 were evaluated by title and abstract; 26 articles followed for full-text reading, and 6 articles were included in this critical review (k=0.98). All articles included detailed parameters and steps about how to diagnose periodontitis. Therefore, it was possible to observe instability and “gray zones” in the staging step, which was due to a lack of priority and an organized order sequence. This review suggests the severity parameters cannot be overcome by complexity parameters, following a cumulative sequence: CAL (1^st), RBL (2^nd), TLP (3^rd), and, after, complexity parameters. An exception must be permitted only for complexity factors between Stages III and IV that can change the initial Stage (III or IV) obtained through the severity analysis, but only between themselves. Moreover, for patients without tooth loss or with TLP of ≤4 teeth (without need for complex rehabilitation) and presenting any type of drifting or flaring or a secondary traumatic occlusion, it cannot be a justification for moving the diagnosis from Stage III to Stage IV.

Sea cucumber peptides are small molecular peptides with biological function obtained from fresh sea cucumber as feedstock, which were hydrolyzed by protease, separated ,and purified. As the main product of sea cucumber refinement, it more accurately expresses the nutritional effect of sea cucumber and has a wide range of potential applications. It has been demonstrated that sea cucumber has a certain value-added effect on bone mineral density regulation, but the differences in bone mineral density regulation of extracts from different parts of sea cucumber and the techniques contributing to the efficient isolation of bone sea cucumber peptides have not been reported. Firstly, the aim of this study was to reveal the differences in osteogenic activities of enzymatic peptides from three major parts of sea cucumber: the body wall, the egg protein, and the intestinal protein. Then, the bone-enhancing sea cucumber peptides were isolated based on the characteristics of the dif-ferences in molecular weight distribution, hydrophilicity, and ionisation degree of sea cucumber, and to explore the possible mechanisms of their action. The findings indicated that sea cucumber peptides extracted from three distinct sites exhibited a dose-dependent enhancement of osteoblast proliferation and differentiation. Upon evaluating the three methods of sea cucumber peptide separation based on molecular weight distribution, hydrophilicity, and ionization, it was observed that the fraction isolated by hydrophobicity and

Background Gingivitis can develop without mechanical cleaning within three weeks. The first clinical sign is bleeding on positive probing. The accumulation of dental biofilm generates an inflammatory gingival response. In the past decade, attention has focused mainly on the interproximal areas and the use of customsized interproximal toothbrushes.The aim of the study was to evaluate the effectiveness of individualized oral hygiene education and its role in dental prevention among patients with dental problems. Methods Before treatment, patients were clinically and radiologically examined, full mouth plaque score (FMPS), full mouth bleeding score (FMBS), and bleeding on brushing (BOB) were recorded, and matrix-metalloproteinase-8 (MMP-8) was measured by using a chair-side MMP-8 measuring system. Patients in group A had gingivitis, but no periodontal damage and patients in group B had periodontal damage. Patients in both groups A and B were identified in to four subgroups based on their toothbrushing habits and the oral health education they received. The three months after initial examination, each patient was examined three more times (2, 4 and 12 weeks later). Results It was concluded that subjects in groups A1 and B1 showed significant reduction in BOB, MMP-8, FMBS and FMPS levels after two weeks. Solo Prophylaxis (A1and B1) remained as a well-constructed protocol with hte complete resolution of interdental inflammation after two weeks. Other subgroups achieved significant reductions only after 12 weeks. Conclusions BOB and MMP-8 are valuable complements in preventive dentistry, and are able to detect potential pathological processes in interproximal spaces. The clinical relevance of BOB, in addition to FMBS, FMPS and gingival inflammation can be demonstrated to patients, which may increase compliance.

Dental agenesis is one of the most common developmental anomaly in humans and it is frequently as-sociated with several other oral abnormalities. The present case describes nonfamilial agenesis of per-manent teeth in a twenty-one-year-old boy, with no apparent systemic abnormalities. The treatment in-cluded a personalized and interdisciplinary approach by the means of endodontics, orthodontics, im-plants supported restorations and prosthetic treatments. The treatment plan was thoroughly elaborated using photographic analysis, study models, orthopantomogram, CBCT and cephalograms. Virtual smile design, diagnostic waxing, and mock-up previsualized the treatment objectives. The edentulous spaces were reconstructed by inserting dental implants, and monolithic Zirconia implant supported restorations. The final results showed a highly aesthetic and functional rehabilitation. Periodic checkups have shown that the stability of the result is well maintained and that the implant supported restorations are an op-timal solution for patients with multiple anodontia.

Osteoporosis (OP), a prevalent skeletal disorder characterized by compromised bone strength and increased susceptibility to fractures, poses a significant public health concern. This review aims to provide a comprehensive analysis of the current state of research in the field, focusing on the application of proteomic techniques to elucidate diagnostic markers and therapeutic targets for OP. The integration of cutting-edge proteomic technologies has enabled the identification and quantification of proteins associated with bone metabolism, leading to a deeper understanding of the molecular mechanisms underlying OP. In this review, we systematically examine recent advancements in proteomic studies related to OP, emphasizing the identification of potential biomarkers for OP diagnosis and the discovery of novel therapeutic targets. Additionally, we discuss the challenges and future directions in the field, highlighting the potential impact of proteomic research in transforming the landscape of OP diagnosis and treatment.

Infrastructure development is rapidly increasing, driving up demand for concrete, a key construction material. Cement and aggregate are essential constituents, with global cement production reaching 4.1 billion metric tons in 2011 and CO2 emissions hitting 1.7 billion metric tons by 2024, a significant contributor to carbon emissions. To address this, alternative constituents like Rice Husk Ash (RHA) and Animal Bone Powder (ABP) are proposed. With rice husk comprising 20% of rice weight and a substantial cattle population in Bangladesh, RHA and ABP offer promising alternatives. This study examines the benefits and limitations of incorporating RHA and ABP into cement, focusing on concrete strength and permeability. By replacing varying percentages of cement with RHA and ABP simultaneously, experiments evaluate their impact on concrete properties after 28 days of curing. The research aims to identify the optimal combination for sustainable concrete production, reducing environmental impact by curbing waste generation and pollution. Results show that compressive strength increases and permeability decreases with up to 5% replacement of RHA and ABP, highlighting their potential for enhancing concrete performance while mitigating environmental concerns.

Objective: This study aimed to assess the impact of artificial intelligence (AI)-driven noise reduction algorithms on metal artifacts and image quality parameters in cone-beam computed tomography (CBCT) images of the oral cavity. Materials and Methods: This retrospective study included 70 patients, 61 of whom were analyzed after excluding those with severe motion artifacts. CBCT scans, performed using a Hyperion X9 PRO 13 × 10 CBCT machine, included images with dental implants, amalgam fillings, orthodontic appliances, root canal fillings, and crowns. Images were processed with ClariCT. AI deep learning model (DLM) for noise reduction. Objective image quality was assessed using metrics such as the differentiation between voxel values (ΔVVs), the artifact index (AIx), and the contrast-to-noise ratio (CNR). Subjective assessments were performed by two experienced readers, who rated overall image quality and artifact intensity on predefined scales. Results: Compared with native images, DLM reconstructions significantly reduced the AIx and increased the CNR (p<0.001), indicating improved image clarity and artifact reduction. Subjective assessments also favored DLM images, with higher ratings for overall image quality and lower artifact intensity (p<0.001). However, the ΔVV values were similar between the native and DLM images, indicating that while the DLM reduced noise, it maintained the overall density distribution. Orthodontic appliances produced the most pronounced artifacts, while implants generated the least. Conclusion: AI-based noise reduction using ClariCT. AI significantly enhances CBCT image quality by reducing noise and metal artifacts, thereby improving diagnostic accuracy and treatment planning. Further research with larger, multicenter cohorts is recommended to validate these findings.

Surgical simulators are crucial in early craniofacial and plastic surgical training, necessitating synthetic materials that accurately replicate tissue properties. Recent critiques of our lab’s currently deployed silicone surrogate have highlighted numerous areas for improvement. To further refine our models, our group's objective is to find a composition of materials that is closest in fidelity to native oral mucosa during surgical rehearsal by expert craniofacial surgeons. Fifteen platinum silicone-based surrogate samples were constructed with variable hardness and slacker percentages. These samples underwent evaluation of tactile sensation, hardness, needle puncture, cut resistance, suture retention, defect repair, and tensile elasticity. Expert craniofacial surgeon evaluators provided focused qualitative feedback on selected top-performing samples for further assessment and statistical comparisons. Evaluation revealed surrogate characteristics with satisfactory to good performance. Sample 977 exhibited the highest performance, and comparison with the original surrogate (sample 810) demonstrated significant improvements in critical areas, emphasizing the efficacy of the refined composition. The study identified a silicone composition that directly addresses the feedback received by our team’s original silicone surrogate. The study underscores the delicate balance between biofidelity and practicality in surgical simulation. The need for ongoing refinement in surrogate materials is evident to optimize training experiences for early surgical learners.

Surgical simulators are crucial in early craniofacial and plastic surgical training, necessitating synthetic materials that accurately replicate tissue properties. Recent critiques of our lab’s currently deployed silicone surrogate have highlighted numerous areas for improvement. To further refine our models, our group's objective is to find a composition of materials that is closest in fidelity to native oral mucosa during surgical rehearsal by expert craniofacial surgeons. Fifteen platinum silicone-based surrogate samples were constructed with variable hardness and slacker percentages. These samples underwent evaluation of tactile sensation, hardness, needle puncture, cut resistance, suture retention, defect repair, and tensile elasticity. Expert craniofacial surgeon evaluators provided focused qualitative feedback on selected top-performing samples for further assessment and statistical comparisons. Evaluation revealed surrogate characteristics with satisfactory to good performance. Sample 977 exhibited the highest performance, and comparison with the original surrogate (sample 810) demonstrated significant improvements in critical areas, emphasizing the efficacy of the refined composition. The study identified a silicone composition that directly addresses the feedback received by our team’s original silicone surrogate. The study underscores the delicate balance between biofidelity and practicality in surgical simulation. The need for ongoing refinement in surrogate materials is evident to optimize training experiences for early surgical learners.

Mass transfer restrictions of scaffolds are currently hindering the development of three-dimensional (3D), clinically viable, and tissue engineered constructs. For this situation, a 3D poly(lactide-co-glycolide)/hydroxyapatite porous scaffold, which was much favorable for transfer of nutrients to and waste products from the cells in the pores, was developed in this study. The 3D scaffold had an innovative structure, including macropores with diameters of 300−450 μm for cell ingrowth and microchannels with diameters of 2−4 μm for nutrition and waste exchange. The mechanical strength in wet state was strong enough to offer the structural support. The typical structure was more beneficial for the attachment, proliferation, and differentiation of rabbit bone marrow mesenchymal stem cells (rBMSCs). The alkaline phosphatase (ALP) activity and calcium (Ca) deposition were evaluated on the differentiation of rBMSCs, and the results indicated that the microchannel structure was very favorable for differentiating rBMSCs into maturing osteoblasts. For repairing rabbit radius defects in vivo, there was rapid healing in the defects treated with the 3D porous scaffold with microchannels, where the bridging by a large bony callus was observed at 12 weeks post-surgery. Based on the results, the 3D porous scaffold with microchannels was a promising candidate for bone defect repair.

Physical activity is widely recognized as a biotherapy by WHO in the fight and prevention of bone diseases such as osteoporosis. It reduces the risk of disabling fractures associated with many comorbidities, and whose repair is a major public health and economic issue. Bone tissue is a dynamic supportive tissue that reshapes itself according to the mechanical stresses to which it is exposed. Physical exercise is recognized as a key factor for bone health. However, the effects of exercise on bone quality depend on exercise protocols, duration, intensity and frequency. Today, the effects of different exercise modalities on capillary bone vascularization, bone blood flow and bone angiogenesis remain poorly understood and unclear. As vascularization is an integral part of bone repair process, the analysis of the preventive and/or curative effects of physical exercise is currently very undeveloped. Angiogenesis-osteogenesis coupling may constitute a new way for understanding the role of physical activity, especially in fracturing or in the integration of bone biomaterials. Thus, this review aims to clarify the link between physical activities, vascularization and bone repair.

Purpose of review: This review investigates the oral microbiome's composition, functions, influencing factors, connections to oral and systemic diseases, and personalised oral care strategies. Recent findings: The oral microbiome is a complex ecosystem consisting of bacteria, fungi, archaea, and viruses that contribute to oral health. Various factors, such as diet, smoking, alcohol consumption, lifestyle choices, and medical conditions, can affect the balance of the oral microbiome and lead to dysbiosis, which can result in oral health issues like dental caries, gingivitis, periodontitis, oral candidiasis, and halitosis. Importantly, our review explores novel associations between the oral microbiome and systemic diseases including gastrointestinal, cardiovascular, endocrinal, neurological conditions, autoimmune diseases, and cancer. We comprehensively review the efficacy of interventions like dental probiotics, xylitol, oral rinses, fluoride, essential oils, oil pulling, and peptides in promoting oral health by modulating the oral microbiome. Summary: This review emphasizes the critical functions of the oral microbiota in dental and overall health, providing insights into the effects of microbial imbalances on various diseases. It underlines the significant connection between the oral microbiota and general health. Furthermore, it explores the advantages of probiotics and other dental care ingredients in promoting oral health and addressing common oral issues, offering a comprehensive strategy for personalized oral care.

The management of erectile dysfunction (ED) shows several grey zones, especially in terms of patient satisfaction and adherence to the treatment. The main and first-line treatment for ED is drug therapy, mainly phosphodiesterase-5 inhibitors (PDE-5is) but the adherence to the therapy is not optimal due to the low patient satisfaction reported in several cases. To address this issue, different administration routes and PDE-5is pharmacological formulations have been introduced in the pharmacological market. The pharmaceutical market has recently seen the introduction of a novel sildenafil oral suspension. This device offers access to all therapeutic regimens in one device, releasing 0.5 mL of suspension containing 12.5 mg of sildenafil with each pulse. This formulation enables tailored dosing based on clinical requirements and the demands of ED patients. Here, we aim to give a brief narrative review of the management of this new oral suspension in order to provide the readers with some suggestions to use in everyday clinical practice, on the basis of the recent evidence, by using an easy and rapid-to-consult questions and answers form. Also included are the conclusions of a board meeting of experienced andrologists regarding the most recent developments in this area.

In this study, we aimed to explore the oral bacteria and fungi that can help discern oral squamous cell carcinoma (OSCC) and investigate the correlations between multiple key pathogens. Methods: Twelve participants (8 females and 4 males; mean age, 54.33 ± 20.65 years) were prospectively recruited into three groups: Group 1: healthy control, Group 2: patients with stomatitis, and Group 3: patients with OSCC, with 4 individuals in each group. Unstimulated whole saliva samples from these participants were analyzed using real-time PCR to assess the presence and abundance of 14 major oral bacterial species and Candida albicans. Results: The analysis revealed significant differences for certain microorganisms, namely Treponema denticola (T. denticola), Lactobacillus casei (L. casei), and Candida albicans. T. denticola was most abundant in the OSCC group (5,358,692.95 ± 3,540,767.33), compared to the stomatitis (123,355.54 ± 197,490.86) and healthy control (9,999.21 ± 11,998.40) groups. L. casei was undetectable in the healthy control group, but was significantly more abundant in the stomatitis group (1,653.94 ± 2,981.98) and even higher in the OSCC group (21,336.95 ± 9,258.79) (p = 0.001). A similar trend was observed for C. albicans, with DNA copy numbers rising from the healthy control (464.29 ± 716.76) to the stomatitis (1,861.30 ± 1,206.15) to the OSCC group (9,347.98 ± 5,128.54) (p = 0.006). The amount of T. denticola was positively correlated with L. casei (r=0.890, p<0.001) and C. albicans (r=0.724, p=0.008). L. casei's DNA copy number was strongly correlated with C. albicans (r=0.931, p<0.001). These three oral microbes exhibited strong positive correlations with each other and had various direct or indirect relationships with other species. Conclusions: In the OSCC group, T. denticola, L. casei, and C. albicans exhibited strong positive correlations with one another, further emphasizing the need for a deeper understanding of the complex microbial interactions in the OSCC environment.

Innovative tissue engineering biomimetic hydrogels based on hydrophilic polymers have been investigated for their physical and mechanical properties. 5% to 25% by volume loading PHEMA-nanosilica glassy hybrid samples were equilibrated at 37°C in aqueous physiological isotonic and hypotonic saline solutions (0.15 and 0.05 M NaCl) simulating two limiting possible compositions of physiological extracellular fluids. The glassy and hydrated hybrid materials were characterized both for dynamo-mechanical properties and equilibrium absorptions in the two physiological-like aqueous solutions. Mechanical and the morphological modifications occurring in the samples have been described. The 5% volume nanosilica loading hybrid nanocomposite composition showed mechanical characteristics in the dry and hydrated states that were comparable to those of cortical bone and articular cartilage, respectively, and then chosen for further sorption kinetics characterization. Sorption and swelling kinetics were monitored up to equilibrium. Changes in water activities and osmotic pressures in the water-hybrid systems equilibrated at the two limiting solute molarities of the physiological solutions have been related to the observed anomalous sorption modes using the Flory-Huggins interaction parameter approach. The bulk modulus of the dry and glassy PHEMA-5% nanosilica hybrid at 37°C has been observed to be comparable with the values of the osmotic pressures generated from the sorption of isotonic and hypotonic solutions. The anomalous sorption modes and swelling rates are coherent with the difference between osmotic swelling pressures and hybrid glassy nano-composite bulk modulus: the lower the differences the higher the swelling rate and equilibrium solution uptakes. Bone tissue engineering benefits of use of tuneable biomimetic scaffold biomaterials that can be “designed” to act as biocompatible and biomechanically active hybrid interfaces are discussed.

Studies on the possible association between bacteria and oral squamous cell carcinoma (OSCC) remain inconclusive, largely due to methodological variations/limitations. The objective of this study was to characterize the species composition as well as functional attributes of the bacteriome associated with OSCC. DNA obtained from 20 fresh OSCC biopsies (cases) and 20 deep-epithelium swabs (matched control subjects) were sequenced for the V1-V3 region using Illumina’s 2x300 bp chemistry. High quality, non-chimeric merged reads were classified to species level using a prioritized BLASTN-algorithm. Downstream analyses were performed using QIIME, PICRUSt, and LEfSe. Fusobacterium nucleatum subsp. polymorphum was the most significantly overrepresented species in the tumors followed by Pseudomonas aeruginosa and Campylobacter sp. Oral taxon 44, while Streptococcus mitis, Rothia mucilaginosa and Haemophilus parainfluenzae were the most significantly abundant in the controls. Functionally, genes involved in bacterial mobility, flagellar assembly, bacterial chemotaxis and LPS synthesis were enriched in the tumors while those responsible for DNA repair and combination, purine metabolism, phenylalanine, tyrosine and tryptophan biosynthesis, ribosome biogenesis and glycolysis/gluconeogenesis were significantly associated with the controls. This is the first epidemiological evidence for association of F. nucleatum and P. aeruginosa with OSCC. Functionally, an “inflammatory bacteriome” is enriched in OSSC.

Bone metastasis detection and quantification on bone scintigraphy is challenging and clinical important for treatment and patient’s life quality. To develop a CNN based diagnostic system for automated segmentation on bone metastasis regions is non-trivial, especially for a small dataset. A dataset in house comprising 100 breast cancer patients and 100 prostate cancer patients is utilized for this research. The Double U-Net model is adapted through the integration of background removal, adding negative samples, and transfer learning methods for bone metastasis detection. The performance is investigated via 10-fold cross-validation and computed in pixel-wise scale. The best model we achieved has precision of 63.08%, sensitivity of 70.82%, and F1-score of 66.72%. The developed system has the potential to provide pre-diagnostic reports for physicians in final decisions and the calculation of the bone scan index (BSI) with the combination with bone skeleton segmentation.

Objectives Bone fractures are very common diseases, which can be caused by impact injuries or physiological disorders. Thus, the present review aimed to study the use of medicinal plants in the healing mechanism of bone fractures. Evidence acquisition Through research in the PubMed, Google Academic, and Scielo databases, this article reviews 11 ethnopharmacological studies and 34 preclinical studies on the biological actions of different plants in bone fracture healing mechanism. Results Indian tribes have highlighted in the plants ethnopharmacological study for various diseases, including bone fractures. However, despite the large citations of traditional use, technical-scientific studies are still scarce in the literature. Chenopodium ambrosioides, Piper sarmentosum, quadrangular Cissus, Ricinus communis and Radix salvia miltiorrhiza plants were the most studied in the literature regarding their osteogenic, angiogenic, anti-inflammatory and remodeling effects, acting on bone receptors, stimulating bone metabolism, increasing minerals uptake, and assisting in free radicals breakdown. Conclusion Thus, the medicinal plants use is promising in the field of bone regeneration, as well as being alternative when conventional therapies are unfeasible, increasing herbal medicines demand and popularity.

Objectives: The goal of this pilot study was to validate and introduce a new AI tool (algorithm), providing and comparing (1) the periodontal/peri-implant diagnosis between professional (specialist) and automated tool, (2) risk assessment and prognostication with the algorithm, and (3) establish cut-off limits for clinically significant disease with a new score system (GF-PeDRA score). Methods: All patients were evaluated by two evaluators, and in case of any divergence, the case was revisited and discussed until clarification and definition. The validation sample constituted 221 patients. The AI tool (GF-PeDRA©) had eighteen parameters to be assessed, involving systemic and local predictors, achieving an octadecagon (an eighteen-sided polygon). The parameters were: (1) The highest probing depth (PD); (2) Number of interproximal sites with bone loss; (3) The highest clinical attachment loss (CAL); (4) Maximum radiographic bone loss (RBL); (5) Bleeding on probing (% BoP); (6) Bone loss pattern; (7) Tooth loss including periodontally hopeless teeth planned for extraction; (8) Evidence of progression over five years; (9) Need for complex rehabilitation; (10) Patient’s age; (11) CAL and biofilm accumulation; (12) Smoking; (13) Diabetes; (14) Extension and distribution of the disease; (15) Peri-implant disease; (16) Other systemic conditions (other than diabetes); (17) Furcation involvement; and (18) Necrotizing lesion. A new score system (GF-PeDRA© score) based on the percentual of the octadecagon area is obtained; if the area was ≥0% to ≤9%, the prognosis is good; ≥10% and ≤ 24%, it is fair; ≥25% and ≤37%, poor; ≥38% and ≤49%, it is questionable; and between ≥50% to ≤100%, the prognosis is hopeless. Results: 221 patients were enrolled, with a mean age of 46.73. 5301 teeth were examined. 187 non-smokers (84.62%) and 34 smokers (15.38%) were included. 193 (87.33%) patients did not have diabetes, whereas 28 (12.67%) had. Comparing the diagnosis between both evaluators, k=0.83; all disagreed cases were re-discussed, and a final decision/diagnosis was reached. After this, the diagnosis found was contrasted with the diagnosis achieved by GF-PeDRA© and a perfect agreement was observed, 100% (k=1.0). 28 patients were diagnosed as periodontally healthy, 55 with plaque-induced gingivitis, and 138 with periodontitis. Only one case of molar/incisor pattern was observed. No peri-implant disease or necrotizing condition was found. The mean CAL found was 3.19 mm; 25 patients (11.31%) had a furcation involvement. The mean percentual of BoP found was 28.67% (median = 19%; maximum: 100%; minimum: 100%); and the mean PD was 5.31 mm. The mean of the new GF-PeDRA© score (ranging from 0% to 100%) was 28.64%, with a median of 32.2% (minimum: 0.6% and maximum: 64.1%). Then, analyzing the GF-PeDRA© score of 221 patients enrolled, 48 (21.73%) were sorted as a Good prognosis for periodontal treatment, 43 (19.45%) had a Fair prognosis, 43 (19.45%) had a Poor prognosis, 68 (30.77%) had a Questionable prognosis, and 19 (8.60%) had a Hopeless prognosis. Conclusion: The new AI tool (GF-PeDRA©) was validated and proved to be extremely helpful in diagnosing and providing risk assessment and prognosis.

The oral microbiome, studied by sampling the saliva or oral rinse, has been long thought to have diagnostic capacity for head and neck cancers (HNC). However, previous reports on the HNC oral microbiome provide inconsistent results. The aim of this study is to consolidate these datasets and determine the oral microbial composition between HNC patients to healthy and premalignant individuals. We analyzed 16 published head and neck cancer (HNC) short-read 16S rRNA sequencing datasets, specifically targeting the V3V4, V4 and V4V5 regions. These datasets included saliva and oral rinse samples from donors with HNC, as well as from healthy and premalignant donors. Differences in diversities and microbial abundance were determined. HNC saliva displayed lower alpha diversity than healthy donors. In contrast, the opposite trend was observed for oral rinse samples. Beta diversity were largely similar across different patient types. Similar oral phyla were detected for all samples, but proportions were largely dependent on sample type (i.e. saliva or oral rinse) and primer set utilised for 16S rRNA sequencing. Neisseria, Leptotrichia and Megasphaera were elevated in healthy saliva, while Mycoplasma was elevated in HNC saliva. Oral rinse and saliva displayed similar enrichment for Fusobacterium, while Veillonella, Alloprevotella, and Campylobacter had conflicting results. The sparse partial least squares discriminant analysis model performed effectively in discriminating HNC from healthy or premalignant patients using V3V4 saliva (AUC = 0.888), and V3V4 oral rinse (AUC = 0.928), while poor discriminative capacity was observed for V4 saliva (AUC = 0.688). In conclusion, our meta-analysis highlighted the limitations of 16S rRNA sequencing, particularly due to variations across study batches, primer sets (i.e. V3V4, V4), and sample types. Hence, caution should be exercised when interpreting 16S rRNA sequencing results across studies, especially when different primer sets and sample types are used.

The human mandible's cancellous bone, which is characterized by its unique porosity and directional sensitivity to external forces, is crucial for sustaining biting stress. Traditional CAD models fail to fully represent bone's anisotropic structure and thus depend on simple isotropic assumptions. For our research, we use the latest versions of nTopology and Creo Parametric software to make biomimetic Voronoi lattice models that accurately reflect the complex geometry and mechanical properties of trabecular bone. The porosity of human cancellous bone is accurately modeled in this work using biomimetic Voronoi lattice models. The porosities range from 70% to 95%, which can be achieved by changing the pore sizes to 1.0 mm, 1.5 mm, 2.0 mm, and 2.5 mm. Finite element analysis (FEA) was used to examine the displacements, stresses, and strains acting on dental implants with a buttress thread, abutment, retaining screw, and biting load surface. The results show that the Voronoi model accurately depicts the complex anatomy of the trabecular bone in the human jaw, compared to standard solid block models. The ideal pore size for biomimetic Voronoi lattice trabecular bone models is 2 mm, taking into account both the von Mises stress distribution over the dental implant, screw retention, cortical bone, cancellous bone, and micromotions. This pore size displayed balanced performance by successfully matching natural bone's mechanical characteristics. Advanced finite element analysis (FEA) improves biomechanical understanding of how bones and implants interact by creating more accurate models of biological problems and dynamic loading situations. This makes biomechanical engineering better.

Growth hormone therapy (GHT) can improve growth velocity and final height but can also accelerated the process of bone growth, which is related to structural bone modelling, both in formation and resorption. The study evaluated the capacity of bone turnover markers to predict early growth response to one year GHT in short stature children born as small for gestational age (SGA). 25 prepubertal SGA children were included. We have estimated P1NP (N-terminal procollagen type 1), CTX (C-terminal telopeptide of collagen type I), P3NP (N-terminal procollagen type III), NT-pro-CNP (amino-terminal C-type natriuretic peptide) and Ca-P metabolism using standard ECLIA, IRA and ELISA methods. A statistically significant increase in bone resorption markers (Ctx ) was found both at 6 and 12 months. P1NP bone markers increased at 6 months and after 12 months of therapy. The P3NP marker of collagen synthesis also increased after 12 months of therapy. We obtained significant increases in phosphorus levels at 6 and 12 months and similarly ALP. We have found a significant correlation between height (cm) and Ctx after 6 -12 months as well as P1NP / height (SD) after 12 months. Calcium levels significantly correlated with height (SD) after 12 months. We find a strong reaction of bone resorption and bone formation markers during growth hormone therapy that may determine their selection as prediction of GH treatment outcome in SGA children. However, the issue requires further research.

During pregnancy, profound physiological changes occur in the maternal body, including those affecting oral health. Dental stem cells (DSCs) have emerged as promising candidates for regenerative therapies in dentistry. This manuscript delves into the intricate interplay between DSC behavior and maternal oral health during pregnancy. We provide an overview of current knowledge concerning the impact of pregnancy on DSCs, highlighting their potential roles in maintaining oral homeostasis and responding to pathological conditions. Additionally, we identify key research gaps and propose future directions for investigating novel therapeutic strategies leveraging DSCs to improve maternal and fetal oral health outcomes. By elucidating this relationship, we aim to pave the way for innovative approaches in preventive and regenerative dentistry tailored to the unique needs of pregnant women.

The aim of the study was the comparison of conventional sintering versus additive manufacturing techniques for β-TCP bioceramics, focusing on mechanical properties and biocompatibility. A "critical" bone defect requires surgical intervention beyond simple stabilization. Autologous bone grafting is the gold standard treatment for such defects but it has its limitations. Alloplastic bone grafting using synthetic materials is becoming increasingly popular. The use of bone graft substitutes has increased significantly and current research was focused on optimizing these substitutes, whereas this study compares two existing manufacturing techniques and the thereby produced β-TCP implants. The 3D-printed β-TCP hybrid structure implant was fabricated using two components, a column structure and a freeze-foam, which were sintered together. The conventionally manufactured ceramics were made by pouring. Both scaffolds were characterized according to porosity, mechanical properties and biocompatibility. The hybrid structure had a total porosity of 74.4 ± 0.5%. Microporous β-TCP implants had a porosity of 43.5 ± 2.4%, while macroporous β-TCP implants had a porosity of 61.81%. Mechanical testing revealed that the hybrid structure had a compressive strength of 10.4 ± 6 MPa, significantly lower than the microporous β-TCP implant’s with 32.9 ± 8.7 MPa. Biocompatibility evaluations showed a steady increase in cell proliferation over time for all β-TCP implants, with minimal cytotoxicity. This study provides valuable insight into the potential of additive manufacturing for β-TCP bioceramics in the treatment of bone defects.

This research addresses a gap in the literature by conducting a comprehensive analysis of patients’ level of satisfaction with dental care. Methods: By combining quantitative and qualitative survey methods with the PSQ questionnaire this study aims to augment ongoing initiatives to enhance dental patients’ experiences by painting a more comprehensive depiction of patients' level of satisfaction; Results: When asked about their overall level of satisfaction 77,1% of the patients said they received excellent services from the office personnel and 72,2% said they trust their doctors; Conclusions: Assessing patient satisfaction in the realm of dental services quality is crucial for enhancing service quality and accuracy, benefiting both patients and dentists, and ultimately improving public health.

Achieving effective haemostasis is crucial for successful outcomes and optimal patient care in contemporary oral surgery. Control of bleeding is essential in procedures like extractions, implant placements, periodontal surgeries, and soft tissue interventions. Efficient management ensures a clear surgical field, reduces post-operative complications, and promotes healing. Local haemostatic agents are essential tools for oral surgeons, offering targeted and controlled methods to achieve haemostasis. These agents include diverse materials and technologies, each with unique mechanisms of action suited to specific surgical scenarios. This review explores the spectrum of local haemostatic agents in contemporary oral surgery, focusing on their efficacy, safety, and practical utility. By examining the characteristics and clinical performance of various haemostatic agents, this review provides valuable insights to guide dentists and oral surgeons in selecting the most appropriate agent for specific situations. A literature search in electronic databases such as Medscape, PubMed-Medline, Science Direct, and EBSCO Host identified 46 publications from 1990 to 2023. This comprehensive examination aims to enhance understanding of local haemostatic agents and their role in advancing the standards of care in contemporary oral surgery.

Non-Vitamin K Oral Anticoagulants (NOACs) have revolutionized anticoagulant therapy, offering improved safety and efficacy over traditional agents like warfarin. This review comprehensively examines the dual roles of NOACs—Apixaban, Rivaroxaban, Edoxaban, and Dabigatran—not only as anticoagulants but also as modulators of inflammation via Protease-Activated Receptor (PAR) signaling. We highlight the unique pharmacotherapeutic properties of each NOAC, supported by key clinical trials demonstrating their effectiveness in preventing thromboembolic events. Beyond their established anticoagulant roles, emerging research suggests that NOACs influence inflammation through PAR signaling pathways, implicating factors such as FXa and Thrombin in the modulation of inflammatory responses. This review synthesizes current evidence on the anti-inflammatory potential of NOACs, exploring their impact on inflammatory markers and conditions like atherosclerosis and diabetes. By delineating the mechanisms by which NOACs mediate anti-inflammatory effects, this work aims to expand their therapeutic utility, offering new perspectives for managing inflammatory diseases. Our findings underscore the broader clinical implications of NOACs, advocating for their consideration in therapeutic strategies aimed at addressing inflammation-related pathologies. This comprehensive synthesis not only enhances understanding of NOACs' multifaceted roles but also paves the way for future research and clinical applications in inflammation and cardiovascular health

Bone drilling is a common procedure used to create pilot holes for inserting screws to secure implants for fracture fixation. However, dis process can increase bone temperature, teh excessive heat can lead to cell death and thermal osteonecrosis, potentially causing early fixation failure or complications. We conducted a three-dimensional dynamic elastoplastic finite element model to evaluate teh propagation and distribution of heat during bone drilling and assess teh thermally TEMPeffected zone (TAZ) dat may lead to thermal necrosis. dis model investigates teh parameters influencing bone temperature during bone drilling, including drill diameter, rotational speed, feed force, and predrilled hole. Teh results indicate dat our FE model is sufficiently accurate in predicting teh temperature rise TEMPeffect during bone drilling. Teh maximum temperature decreases exponentially wif radial distance. When teh feed forces are 40 and 60 N, teh maximum temperature does not exceed 45 °C. However, wif feed forces of 10 and 20 N, both teh maximum temperature exceeds 45 °C wifin a radial distance of 0.2 mm, indicating a high-risk zone for potential thermal osteonecrosis. Wif teh two-stage drilling procedure, where a 2.5 mm pilot hole is pre-drilled, teh maximum temperature can be reduced by 14 °C. dis suggests dat higher feed force and rotational speed and/or using a two-stage drilling process could mitigate bone temperature elevation and reduce teh risk of thermal osteonecrosis during bone drilling.

Background/Objectives: Dental implants have become a cornerstone of restorative dentistry, providing a long-lasting method for tooth replacement. The level of osseointegration has a big impact on the biomechanical stability at the bone-implant contact (BIC), which determines how long these implants will work. However, the exact consequences of changing osseointegration levels on different implant designs, especially in bones with variable densities, are not well known. Three short dental implants were tested in this study: BioMet 3iT3, Straumann® Standard Plus Short Regular Neck (SPS-RN), and Straumann® Standard Plus Short-Wide Neck (SPS-WN). 3D finite element analysis (FEA) was used to look at how well they worked biomechanically. This paper tests the implants at four stages of osseointegration: 25%, 50%, 75%, and 100% in both high-density (Bone Type III) and low-density (Bone Type IV) cancellous bone. It also created and examined realistic CAD models under static occlusal loading conditions to assess stress distribution and major strains at the bone-implant contact.; Results: The study discovered that as osteointegration increases, von Mises stress and principal strains go down significantly for all implant types. The SPS-WN implant had the lowest strain values, especially for bone with low density. These reductions demonstrate increased mechanical stability as the bone-implant inter-face becomes more capable of dispersing mechanical stresses, minimizing the potential for localized deformation and bone resorption.; Conclusions: The results highlight the importance of achieving optimum osseointegration to reduce mechanical stress and increase the lifespan of dental implants. The SPS-WN type implant performed better in biomechanical tests than the others, especially when bone conditions were not ideal. This makes it a great choice for clinical applications that need long-term implant success.

Abstract Background: Periodontitis is associated with systemic chronic inflammatory diseases. There is limited evidence on the influence of anti-cytokine therapies on the periodontal condition and microbiome in the tooth pocket of such patients, so the aim of this study was to elucidate this issue. Methods: In this observational trial, the periodontal status and the gingival crevicular fluid of 13 patients with different chronic inflammatory diseases were obtained before initiation of anti-cytokine treatment and 14 weeks after. Gingival crevicular fluid was collected for 16S rRNA gene sequencing from a clinically healthy tooth and the deepest measured pocket. Results: In participants with advanced attachment loss at baseline, the clinical attachment level significantly decreased from 2.9 (2.3-3.4) to 2.4 (1.3-3.0) mm (p = 0.04), and the bleeding- on-probing index dropped from 19.4 (10.0-21.0) to 7.3 (6.9-9.9) mm (p = 0.02) without any further periodontal treatment. Shannon’s diversity index significantly increased in the deepest pockets of patients (p = 0.039). Conclusion: The data showed alterations in diversity of the subgingival microbiome and improvement of periodontal parameters over the course of the study, implying a shift towards a healthier condition after starting anti-cytokine therapy. Additional investigations are needed to analyze whether the administration of selective biologicals can improve periodontal conditions in patients with or without chronic inflammatory diseases.

In bone tissue engineering, ceramics have been the choice due to their excellent biological properties. But the paradigm changed with the discovery of bioactive glasses (BGs) in 1969 by Larry Hench and co-workers, due to their ability to bond to living tissues through the formation of an interfacial bone-like hydroxyapatite layer when the bioglass was put in contact with biological fluids in vivo. Among a number of tested compositions, the one exhibiting the highest bioactivity index is the well-known trademarked 45S5 Bioglass®. The topic received increasing attention particularly after 1985 when this material entered in the market of biomedical devices, inspiring many other investigations aiming at further exploring the in vitro and in vivo performances of this BG, or developing other related BG compositions. The research efforts gradually revealed a number of shortcomings of 45S5 Bioglass®, mostly derived from its high sodium content, initially intended to decrease the melting temperature and accelerating the degradation of the silicate network over time. But the extensive release of sodium from 45S5 Bioglass® in the biological fluids creates a high pH cytotoxic environment. Other serious drawbacks include a fast degradation rate, and a poor sintering ability, which hinders the reliable fabrication of porous scaffolds. Therefore, sol-gel was regarded as an attractive alternative to prepare alkali-free BG compositions. The process uses inorganic and/or organic precursors, which undergo hydrolysis and condensation at room-temperature, being less costly. When properly conducted, the sol-gel process might result in amorphous structures with all the components intimately mixed at the atomic scale. Moreover, developing new better performing materials for bone tissue engineering is a growing concern, as the ageing of the world’s population leads to lower bone density and osteoporosis. This work describes the sol-gel synthesis of a novel quaternary silicate-based BG with the composition 60 SiO2 – 34 CaO – 4 MgO – 2 P2O5 (mol%) was prepared using acidified distilled water as single solvent. By controlling the kinetics of the hydrolysis and condensation steps, an amorphous glass structure could be obtained. The results of XRD of samples calcined within the temperature range from 600-900 ºC demonstrated that amorphous nature was maintained until 800 ºC, followed by partial crystallization at 900 ºC. The specific surface area, an important factor in osteoconduction, was also evaluated over different temperatures, ranging from 160.6 ± 0.8 m2/g at 600 ºC down to 2.2 ± 0.1 m2/g at 900 ºC, being accompanied consistent changes in average pore size and agreeing pore size distribution. The immersion of the BG particles in simulated body fluid (SBF) led to the formation of an extensive apatite layer on its surface. These overall results indicate the proposed material is very promising for biomedical applications in bone regeneration and tissue engineering.

Abstract. Graphene family (GF)-Calcium phosphate (CaP) composites, holds great potential as components of bone regeneration materials. GF nanomaterials can be modified physically as well as chemically, which are to be biomimetic, mechanically to be hard due to their capability to support exceptional mechanical, thermal and electronic properties. These biocompatible GF composites coated on the calcium phosphate can enhance and tolerate stem cell growth and differentiation, proliferation into various lineages or interact with bioorganisms. The development in CF-CaP materials and their physicochemical/biointeractions and strategies towards osteoblasts is a great concern to promote faster healing and reconstructions of large bone imperfections or defects. In this review, we explain the influence of the CF-CaP and summarize recent developments on designing CF-CaP architectures as multifunctional bone regeneration platforms. We have also explored the typical biological applications concerning these CF-CaP based bioactive nanocomposites. Furthermore, the future viewpoints and evolving challenges will also be emphasized. Due to the shortage of full-length reviews in this emerging research field, this review would be caught great attention and encourage various new chances across a wider range of disciplines.