We report on the use of quartz-enhanced photoacoustic spectroscopy (QEPAS) for multi-gas detection. Photo-acoustic (PA) spectra of mixtures of water (H2O), ammonia (NH3) and methane (CH4) were measured in the mid-infrared (MIR) wavelength range using a MIR (mid-infrared) optical parametric oscillator (OPO) light source. Highly overlapping absorption spectra is a common challenge for gas spectroscopy. To mitigate this, we use a partial least-squares regression (PLS) method to estimate the mixing ratio and concentrations of the individual gasses. The concentration range explored in the analysis varies from a few parts-per-million (ppm) to thousands of ppm. Spectra obtained from HITRAN and experimental single-molecule reference spectra of each of the molecular species were acquired and used as training data sets. These spectra were used to generate simulated spectra of the gas mixtures (linear combinations of the reference spectra). Here in this proof-of-concept experiment we demonstrate that after an absolute calibration of the QEPAS cell, the PLS analyses could be used to determine concentrations of single molecular species with a relative accuracy within a few % for mixtures of H2O, NH3 and CH4 and with an absolute sensitivity of approximately 300(±50) ppm/V, 50(±5) ppm/V and 5(±2) ppm/V for water, ammonia and methane, respectively. Thus, demonstrating that QEPAS assisted by PLS is a powerful approach to estimate concentrations of individual gas components with considerable spectral overlap, which is a typical scenario for real-life adoptions and applications.

This paper aims to propose improvements for plastic waste management in Salvador – the Brazilian third most populated metropolis – via Partial Least Squares Structural Equation Modeling (PLS-SEM). All indicators, constructs, and hypotheses regarding collection, sorting, recycling, and disposal in the proposed PLS model were derived from the literature review, and the dependence of the performance construct on efficiency, effectiveness, municipality's socioeconomic aspects and municipality infrastructure is evaluated. Academic and practitioner publics were surveyed, and after analysis in both SmartPLS and RStudio software, suggestions for improvement regarding plastics recycling rate, market maturity, and infrastructural aspects for optimized reverse logistics were made. Since almost double the minimum number of respondents answered the survey questionnaire and the PLS-SEM statistics showed that the modeling presents consistency, the discussion is relevant. The model can and will evolve, but examples of suggested improvement are the installation of Deposit-Return Systems (DRS) in parks, streets, and avenues for increasing selective collection and the direct purchasing of waste from residents by municipal administration, compensating them with vouchers for food. The model can be a basis for other cities worldwide sharing analogous characteristics. By considering it, organizations can contribute to both reduced Greenhouse Gas (GHG) emissions and reduced terrestrial pollution.

In economics, especially econometrics, fixed-effects are widely recognized as powerful tools for heterogeneity analysis of longitudinal data sets. However, the existing research pays more attention to such as the variable selection, parameter estimation and dimension reduction on linear relationships with too many assumptions while nonlinear relationships are ubiquitous. In this paper, an extension fixed-effects model is proposed on the curve_fit nonlinear least squares. First, with the help of expert knowledge, the series regressions between independent variables including time and dependent variable is estimated on each series data, and the parameters are estimated by curve_fit. Similarly, the coeffection between independent variables including time and dependent variable is also initially estimated on the whole panel data. Second, the distance between regressions is defined, and then the coeffect function between the series regressions is obtained on the initial co-effect with curve_fit. Third, the time-effects and individual fixed-effects for each series data in the panel data are estimated on the differences of series regressions and co-effect function. Additionally, the effectiveness of the proposed method is varified on the synthetic data.

Acrylamide is probably carcinogenic to humans (International Agency for Research on Cancer, group 2A) with major occurrence in heated, mainly carbohydrate-rich foods. For roasted coffee, a European Union benchmark level of 400 µg/kg acrylamide is of importance. Regularly, the acrylamide contents are controlled using liquid chromatography combined with tandem mass spectrometry (LC-MS/MS). This reference method is reliable and precise but laborious because of the necessary sample clean-up procedure and instrument requirements. This research investigates the possibility of predicting the acrylamide content from proton nuclear magnetic resonance (NMR) spectra that are already recorded for other purposes of coffee control. In the NMR spectrum acrylamide is not directly quantifiable, so that the aim was to establish a correlation between the reference value and the corresponding NMR spectrum by means of a partial least squares (PLS) regression. Therefore, 40 commercially available coffee samples with already available LC-MS/MS data and NMR spectra were used as calibration data. To test the accuracy and robustness of the model and its limitations, 50 coffee samples with extreme roasting degrees and blends were additionally prepared as test set. The PLS model shows an applicability for the varieties C. arabica and C. canephora, which were medium to very dark roasted using drum or infrared roasters. The root mean square error of prediction (RMSEP) is 79 µg/kg acrylamide (n=32). The PLS model is judged as suitable to predict the acrylamide values of commercially available coffee samples. On the other hand, very light roasts containing more than 1000 µg/kg acrylamide are currently not suitable for PLS prediction.

The purpose of this paper is threefold: (i) to introduce and study the Euler-Lagrange prolongations of flatness PDEs solutions (best approximation of flatness) via associated least squares Lagrangian densities and integral functionals on Riemannian manifolds; (ii) to analyze some decomposable multivariate dynamics represented by Euler-Lagrange PDEs of least squares Lagrangians generated by flatness PDEs and Riemannian metrics; (iii) to give examples of explicit flat extremals and non-flat approximations.

Stroke often results in impaired gait, which can limit community ambulation and the quality of life. Recent works have shown the feasibility of transcranial Direct Current Stimulation (tDCS) as an adjuvant treatment to facilitate gait rehabilitation. Since the cerebellum plays an essential role in balance and movement coordination, which is crucial for independent overground ambulation, so, we investigated the effects of cerebellar tDCS (ctDCS) on the post-stroke overground gait performance in chronic stroke survivors. Fourteen chronic post-stroke male subjects were recruited based on convenience sampling at the collaborating hospitals where ten subjects finally participated in the ctDCS study. We evaluated the effects of two ctDCS montages with 2mA direct current, a) optimized configuration for dentate stimulation with 3.14cm² disc anode at PO10h (10/5 EEG system) and 3.14cm² disc cathode at PO9h (10/5 EEG system), and b) optimized configuration for leg lobules VII-IX stimulation with 3.14cm² disc anode at Exx8 (electrodes defined by ROAST) and 3.14cm² disc cathode at Exx7. We found ctDCS to be acceptable by all the exposed subjects. The ctDCS intervention had an effect on the 'Normalised Step length Affected side' (p=0.1) and 'Gait Stability Ratio' (p=0.0569), which was found using Wilcoxon signed-rank test at 10% significance level. Also, ctDCS montage specific effect was found using a two-sided Wilcoxon rank-sum test at a 5% significance level for 'Step Time Affected Leg' (p=0.0257) and '%Stance Time Unaffected Leg' (p=0.0376). Moreover, the changes in the quantitative gait parameters across both the montages were found to be correlated to the mean electric field strength in the lobules based on partial least squares regression analysis (R² statistic = 0.6574) where the mean electric field strength at the cerebellar lobules, Vermis VIIIb, Ipsilesional IX, Vermis IX, Ipsilesional X, had the most loading. In conclusion, our feasibility study indicated the potential of a single session of ctDCS to contribute to the immediate improvement in the balance and gait performance in terms of gait-related indices and clinical gait measures.

Although, staging models gained momentum to stage define affective disorders, no attempts were made to construct mathematical staging models using clinical and biomarker data in patients with major depression and bipolar disorder.The aims of this study were to use clinical and biomarker data to construct statistically-derived staging models, which are associated with early lifetime traumata (ELTs), affective phenomenology and biomarkers.In the current study, 172 subjects participated, 105 with affective disorders (both bipolar and unipolar) and 67 controls. Staging scores were computed by extracting latent vectors (LVs) from clinical data including ELTs, recurring flare ups and suicidal behaviors, outcome data such as disabilities and health-related quality of life (HR-QoL), and paraoxonase (PON)1 actvities and nitro-oxidative stress biomarkers.Recurrence of episodes and suicidal behaviors could reliably be combined into a LV with adequate composite reliability (the “recurrence LV”), which was associated with female sex, the combined effects of multiple ELTs, disabilities, HR-QoL and impairments in cognitive tests. All those factors could be combined into a reliable “ELT-staging LV” which was significantly associated with nitro-oxidative stress biomarkers. A reliable LV could be extracted from serum PON1 activities, recurrent flare ups, disabilities and HR-QoL.Our ELT-staging index scores the severity of a relevant affective dimension, shared by both major depression and bipolar disorder, namely the trajectory from ELTs, a relapsing course and suicidal behaviors to progressive disabilities. Patients were classified into three stages, namely an early stage; a relapse-regression stage; and a suicidal-regression stage. Lowered lipid-associated antioxidant defenses may be a drug target to prevent the transition from the early to the later regression stages.

Reverse-order laws for generalized inverses of matrix products is a classic object of study in the theory of generalized inverses. One of the well-known reverse-order laws for a matrix product AB is (AB)^(i,...,j) = B^(i,...,j)A^(i,...,j), where (·)^i,...,j denotes an {i,...,j}-generalized inverse of matrix. Because {i,...,j}-generalized inverse of a general matrix is not necessarily unique, the relationships between both sides of the reverse-order law can be divided into four situations for consideration. In this article, we first introduce a linear mixed model y = ABβ + Aγ + ε, present two least-squares methodologies to estimate the fixed parameter vector  in the model, and describe the connections between the two least-squares estimators and the reverse-order laws for generalized inverses of the matrix product AB. We then prepare some valued matrix analysis tools, including a general theory on linear or nonlinear matrix identities, a group of expansion formulas for calculating ranks of block matrices, two groups of explicit formulas for calculating the maximum and minimum ranks of B^(i,...,j)A^(i,...,j), as well as necessary and sufficient conditions for B^(i,...,j)A^(i,...,j) to be invariant with respect to the choice of A^(i,...,j) and B^(i,...,j). We then present a unied approach to the 512 set inclusion problems {(AB)^(i,...,j) ⊇ {B^(i,...,j)A^(i,...,j)}for the eight commonly-used types of generalized inverses of A, B, and AB using the block matrix representation method (BMRM), matrix equation method (MEM), and matrix rank method (MRM), where {(·)^(i,...,j)} denotes the collection of all {i,...,j}-generalized inverse of a matrix.

In this paper, the optimal approximation algorithm is proposed to simplify non-linear functions and/or discrete data as piecewise polynomials by using the constrained least squares. In time-sensitive applications or in embedded systems with limited resources, the runtime of the approximate function is as crucial as its accuracy. The proposed algorithm search to find the Optimal Piecewise Polynomial (OPP) with minimum computational cost while ensuring the error below a specified threshold. This was accomplished by using smooth piecewise polynomials with optimal order and number of intervals. The computational cost only depends on polynomial complexity, i.e., the order and the number of intervals at runtime function call. For optimal approximation, computational costs for all the possible combinations of piecewise polynomials were calculated and tabulated as ascending order for the specific target CPU off-line. Each combination was optimized through constrained least squares and random selection method for given sample points. Afterward, whether the approximation error is below the predetermined value is examined. When the error is permissible, the combination is selected as the optimal approximation or the next combination was examined. To verify the performance, several representative functions were examined and analyzed.

Empirical equations representing, interpolating and smoothing groups of measurement results by regression methods are in widespread use in metrology and other fields of science and engineering. Standard equations for the propagation of measurement uncertainties to values computed from such equations are available but suffer from a lack of general acceptance and are only infrequently applied in practice. One reason for the slow uptake is the lack of clear methods to account for systematic error. In this paper, uncertainty propagation equations in terms of covariance matrices are generalized to allow for systematic errors in least-squares regression, and effects of the resulting uncertainties are investigated analytically. A stochastic ensemble model of systematic error is proposed for the computation of the non-diagonal elements of the weight matrix of the Generalized Least-Squares method (GLS) from the measurement uncertainty. A GLS projector formalism is described which separates the effects of measurement scatter on values calculated by the equation from those on the related “residuals”, i.e., the residual errors in the fitted data. The same projectors act similarly on the associated uncertainties and covariance matrices and permit the effects of systematic errors on the simulation covariance to be quantified. It is demonstrated that, in order to include systematic errors in the uncertainty estimates of GLS, covariance matrices may be substituted by novel, specifically defined dispersion matrices that are not specified yet by the GUM[1]. Systematic measurement errors may be estimated from various sources; a particularly easy way suggested here involves analyzing the structure in the regression residuals. It is demonstrated that GLS projectors exhibit inherent features of “error blindness” also with respect to systematic errors. [1] GUM: Guide to the Expression of Uncertainty in Measurement, http://www.bipm.org/en/publications/guides

Intelligent transportation systems (ITS) have recently evolved rapidly, which requires development of highly trustworthy and effective communication technologies for uses, including vehicle-to-vehicle (V2V) and vehicle-to-everything (V2X) communication; where Orthogonal Frequency Division Multiplexing (OFDM) is regarded as a strong candidate and highly popular option technique among these methods. However, the movement of vehicles introduces Doppler frequencies which produce inter-carrier interference (ICI), that is frequently occurs in V2X channels. This interference has the potential to compromise the integrity of subcarrier orthogonality within OFDM, leading to lower-quality communication and an increased likelihood of data transmission errors. When employing channels with doubly dispersive fading, OFDM necessitates the usage of a complex equalization based on the minimum mean-square error (MMSE) equalizer, which requires channel matrix inversion. Several low-complexity equalizers for OFDM have been developed and are based on band factorization, time domain LSQR (Least-Square QR) iterative computing, and banded minimum mean squared error (BMMSE). This paper proposes Conjugate Gradient Least Squares (CGLS), which is a novel iterative computation algorithm integrated with nonlinear equalizers. The suggested nonlinear equalization technique determines the trade-off between computations and performance. According to simulation data, the suggested nonlinear equalizer performs better than the current BMMSE and linear CGLS algorithms across doubly dispersive fading channels.

Spatial interpolation of meteorological data can have immense implications on risk management and climate change planning. Kriging with external drift (KED) is a spatial interpolation variant that uses auxiliary information in the estimation of target variable at unobserved locations. However, the traditional KED methods with linear trend functions may not be able to capture the complex and non-linear interdependence between target and auxiliary variables, which can lead to an inaccurate estimation. In this work, a novel KED method using least squares support vector regression (LSSVR) is proposed. This machine learning algorithm is employed to construct trend functions regardless of the type of variable interrelations being considered. To evaluate the efficiency of the proposed method (KED with LSSVR) relative to the traditional method (KED with a linear trend function), a systematic simulation study for estimating the monthly means temperature and pressure in Thailand in 2017 was conducted. The KED with LSSVR is shown to have superior performance over the KED with the linear trend function.

Introducing the Moving Least-Squares Aided Finite Element Method (MLS-FEM), we present a robust computational technique that effectively evaluates the development of mixing in polymeric mixing devices. Our approach uses the Moving Least-Squares (MLS) interpolant to enhance the classic finite element shape functions. As a result, it becomes possible to treat fixed or moving components, such as rotors of a mixer, as discontinuities within the flow domain. This allows analysis of the flow field with a background mesh independent of the rotors' shape, orientation, and position. We compared the MLS-FEM results with the classical boundary-fitted mesh FEM, which comprises the mesh regeneration steps by the movement of the rotors. We then showed that the new method provides accurate results for the flow field parameters (i.e., the velocity components and the pressure values) and the mixing evolution without requiring mesh regeneration and without compromising accuracy.

The research reported on this paper was aimed at improving the overall efficiency of a PDO certified artisanal cheese production process. Being a PDO certified foodstuff by the EU, it is considered to have properties and qualities determined by the geographical environment in which is made, with its production taking place in a specific and determined geographical location, in this case the Serra da Estrela region. In that sense, the authors conducted a mapping according to a systemic perspective of the processes involved in the context of manufacturing and distribution of certified Serra da Estrela cheese. Numerous methods were used throughout the process, such as a systemic design analysis, and techniques derived from ethnographic methods, which led to the collection of data in the field and consequently provided the immersion of the researcher in genuine work situations. Critical points were identified and emphasized in the systemic map with the purpose of encouraging initiatives to address and overcome the gaps and inefficiencies detected. The systemic design analysis triggered the development of design work. Observations following an ethnographic approach identified ergonomic risks in cheese making during the process of cutting excess chips, fostering the emergence of musculoskeletal disorders at the wrist. A tool that fits best to the task at hand was developed. A prototype of the new tool enabled collecting feedback from use in the work context, in order to inform product development. The domains of agricultural production and microbiology, considering the specific microorganisms developed trough the ripening process of the cheese, turned out to be aspects of high importance for the issue under focus, contributing to a broader understanding of the ripening process and its risks, simultaneously improving the efficiency and success of cheese production. If it were not for the systemic analysis, which served as a link between the boundaries of distinct domains such as the risk of microorganism contamination, ergonomics, energy efficiency, legislation and regulation policies, transportation challenges and economic viability, approached throughout the research. Simultaneously creating bridges between them, the various problems might not have been detected in the first place, as they are usually addressed in specialized disciplines, predetermined by the restrictions of each specific area of knowledge. As a consequence of the development of this research, which was based on an analysis that sought to establish possible connections between various disciplines and tried to constantly maintain a holistic perspective, making new connections and observing the issues from a new angle, apart from the already established methodologies. All this allowed to lay out the seeds for the development of a plan to tackle the critical points identified by the systemic analysis reported in this paper.

The profile of secondary metabolites occurring in apple cuticular layer is not only characteristic for particular apple cultivar, but also dynamically reflects various external factors in growing environment. In this study, the possibility to authenticate apple samples based on analysis of their cuticular layer extracts was investigated. Ultra-high-performance liquid chromatography coupled to high resolution tandem mass spectrometry (UHPLC-HRMS/MS) was employed for obtaining metabolomic fingerprints. In total, 274 authentic apple samples, four cultivars harvested within the seasons 2020 to 2022 in the Czech Republic and Poland were analysed. The generated complex data processed by univariate and multivariate statistical methods enabled to build classification models for discrimination of apple cultivars as well as their geographical origin. The models showed very good performance in differentiation of Czech and Polish samples for three of four cultivars: ‘Gala’, ‘Golden Delicious’ and ‘Idared’, moreover, the validity of the models was verified over harvest seasons. The diagnostic markers, besides metabolites of triterpene biosynthetic pathway, mainly represented wax esters. ‘Jonagold’, which is known to be susceptible to mutations, was the only cultivar for which the unambiguous classification of geographical origin was not possible.

The concept of green energy is now at the forefront of development discourse, with the United Nations Sustainable Development Goals (SDGs) 7, 11, and 12 all aimed at promoting green energy consumption to combat the three planetary crises: climate change, biodiversity loss, and pollution. Similarly, issues regarding Africa’s natural resource curse have caused a stir in the growth and development literature for some time now and there is no sign that it will die out. This study, the first of its kind, simultaneously assesses the impact of green energy consumption and Africa’s natural resources rents on economic growth by applying the Feasible Generalized Least Square (FGLS) estimator and the dynamic panel models of the Pooled Mean Group (PMG) and Mean Group (MG) estimators on data from 1990 to 2020 for 24 selected African countries. The results show that green energy consumption has a short-run growth-limiting effect and a long-run growth-enhancing effect in Africa. The study also found evidence of the natural resource curse phenomenon in Africa. The study, therefore, calls for the advancement and usage of green energy for both domestic and industrial production in Africa. The study further calls for a revamp in the global tax policy to curb illicit financial activities and strengthening institutional quality for transparency and accountability in the entire value chain of natural resource management in Africa.

Partial least square (PLS) regression is a well-known chemometric method used for predictive modelling, especially in the presence of many variables. Although PLS was not initially developed as a technique for classification tasks, scientists have reportedly used this approach successfully for discrimination purposes. Whereas some non-supervised learning approaches including but not limited to PCA, and k-means clustering do well in identifying/understanding grouping and clustering patterns in multidimensional data, they are limited when the end target is discrimination, making PLS a preferable alternative. A total of fertilized 672 chicken egg hyperspectral imaging data, consisting of 336 white eggs and 336 brown eggs were used in this study. Hyperspectral images in the NIR region of 900-1700 nm wavelength range were captured prior to incubation on day 0 and on days 1-4 after incubation. Eggs were candled on incubation day 5 and broken out on day 10 to confirm fertility. While a total number of 312 and 314 eggs were found to be fertile in the brown and white egg batches respectively, total numbers of non-fertile eggs in the same set of batches were 23 and 21 respectively. Spectral information was extracted from a segmented region of interest (ROI) of each hyperspectral image and spectral transmission characteristics were obtained by averaging the spectral information. A moving-thresholding technique was implemented for discrimination based on PLS regression results on the calibration set. With true positive rates (TPR) of up to 100% obtained at selected threshold values of between 0.50-0.85 and on different days of incubation, the results indicated that the proposed PLS technique can accurately discriminate between fertile and non-fertile eggs. The adaptive PLS approach was thereby presented as suitable for handling hyperspectral imaging-based chicken egg fertility data

Empirical models for intensive or extensive margins of trade that relate measures of exports to firm characteristics are usually estimated by variants of (generalized) linear models. Usually, the firm characteristics that explain these export margins enter the empirical model in linear form, sometimes augmented by quadratic terms or higher order polynomials, or interaction terms, to take care or test for non-linear relationships. If these non-linear relationships do matter and if they are ignored in the specification of the empirical model this leads to biased results. Researchers, however, can never be sure that all possible non-linear relationships are taken care of in their chosen specifications. This note uses for the first time the Kernel-Regularized Least Squares (KRLS) estimator to deal with this issue in empirical models for margins of exports. KRLS is a machine learning method that learns the functional form from the data. Empirical examples show that it is easy to apply and works well. Therefore, it is considered as a useful addition to the box of tools of empirical trade economists.

Plant cells' ability to withstand abiotic stress is strongly linked to modifications in their mechanical characteristics. Nevertheless, the lack of a workable method for consistently tracking plant cell mechanical properties severely restricts our comprehension of the mechanical alterations in plant cells under stress. With Polyethylene Glycol (PEG6000), we created a drought-like environment, and we used the Double Resonator Piezoelectric Cytometry (DRPC) method to dynamically and non-invasively track changes in the stress (ΔS) created and viscoelasticity (storage modulus G' and loss modulus G") of protoplasts and suspension cells of rice during drought stress. The findings demonstrate that, rice suspension cells and protoplasts react mechanically differently to 5%–15% PEG6000 stress, implying distinct resistance mechanisms. However, neither of them can withstand 25% PEG6000 stress, they respond mechanically similarly to 25% PEG6000 stress. The results of DRPC are further corroborated by the morphological alterations of rice cells and protoplasts observed under an optical microscope. To sum up, the DRPC technique functions as a precise cellular mechanical sensor and offers novel research tools for the evaluation of plant cell adversity and differentiating between the mechanical reactions of cells and protoplasts under abiotic stress.

Face recognition is a key computer vision task that focuses on identifying or verifying individuals using their facial features. This task becomes more difficult with low-resolution images, where the reduced pixel count and detail make it harder to extract and match features accurately. In this study, we assess the effectiveness of Multilinear Side-Information-based Discriminant Analysis (MSIDA) on low-resolution images, using the CelebA database as a reference. The system showed strong performance, achieving 90.60% accuracy on high-resolution and 88.23% on low-resolution images, highlighting the robustness and effectiveness of MSIDA.

The generation of forensic DNA profiles consisting of single nucleotide polymorphisms (SNPs) is now being facilitated by wider adoption of next-generation sequencing (NGS) methods in casework laboratories. At the same time, and in part because of this advance, there is an intense focus on the generation of SNP profiles from evidentiary specimens for so-called forensic or investigative genetic genealogy (FGG or IGG) applications. However, FGG methods are constrained by the algorithms for genealogical database searches, which were designed for use with single-source profiles, and the fact that many forensic samples are mixtures. To enable the use of two-person mixtures for FGG, we developed a workflow, MixDeR, for the deconvolution of mixed SNP profiles. MixDeR, a flexible and easy to use R package and Shiny app, processes ForenSeq Kintelligence® (QIAGEN, Inc.) SNP genotyping results and directs deconvolution of the profiles in EuroForMix (EFM). MixDeR then filters the EFM outputs to produce inferred single-source genotypes in reports formatted for use with GEDmatch® PRO. An optional MixDeR output includes metrics that assist with testing and validation of the workflow. As the Shiny app provides a graphical user interface and the software is designed to be run offline, MixDeR should be suitable for use by any laboratory developing FGG capabilities, no matter their bioinformatic resources or expertise.

In this study, we investigate the growth of EV ownership among Swedish households. Through detailed socio-economic data and the Swedish vehicle register, we are able compare characteristics of households that bought an EV in 2016 with those that became EV owners in 2020. We are thus able to describe and analyse the transition from the early EV owners to the early majority. Unlike many prior studies in the field, which are based on surveys or interviews, this study relies on registry data, thereby encompassing all car owners in Sweden. In this study, we have also scrutinized the significance of ownership mode by distinguishing between households that have chosen to purchase a car and those that have chosen to lease one. The results show that the demand for EVs has reached new consumer groups, e.g. both younger and older car buyers, and that the option to lease a car privately has broadened the market for new cars in general, and for EV’s in particular.

Regulation of the diet in terms of the content of soluble and insoluble fibre is of great importance from the point of view of dietetics, microbiology of the gastrointestinal tract and immunology of the organism. Dietary fibre plays an important role in maintaining the balance between the con-tinuity of gut mucus production (intestinal mucosa), the stability of the intestinal microbiome composition, the regeneration of the intestinal epithelium and the immune status within the gut-associated lymphoid tissue (GALT) are played by pectin and their metabolic products in the form of pectin oligosaccharides. The main purpose of this review was to focus on pectin, their functions, their impact on the human's health and on some of the most promising prebiotics due to their solubility in the gastrointestinal tract in the form of pectin oligosaccharides. They have the properties of pectin, but have also additional features and postbiotics obtained in fermentation process can affect the intestinal microbiome and GALT-related immunity. They can be obtained from plant agro-wastes.

The temperature variations caused by the climate changes taking place in the Basilicata region, southern Italy - Ionian Seaside of the Gulf of Taranto - on the territory of the DOP Matera vineyard, were studied by means of an analysis of temperature trends considering both the period of the vegetative-productive season of the vineyards and the whole year. Two datasets were analyzed for this study: data from ERA5-Land of the C3S Climate Data Store -relative to the 1981-2022 window- and data from 5 weather stations belonging to the agrometeorological network of the Lucanian Agency for Development and Innovation in Agriculture (SAL-ALSIA), relative to the 2000-2023 window. From the results of this study, it can be deduced that, for the historical period analyzed, the Matera DOP area showed a clear and worrying trend of increasing temperatures and, in par-ticular, minimum temperatures. This increase, moreover, is more evident at higher elevations than at lower elevations close to the sea. At lower altitudes, in fact, temperatures are strongly “buffered” by the thermoregulatory activity of the bordering Ionian Sea. It follows that the DOP Matera viticultural areas, and in particular the areas furthest from the coastal strip, will already have to adapt to severe climatic conditions that will undoubtedly affect the quality and typicality of the wines.

In the current era of ‘big data’, scientists are able to quickly amass enormous amount of data in a limited number of experiments. The investigators then try to hypothesize about the root cause based on the observed trends for the predictors and the response variable. This involves identifying the discriminatory predictors that are most responsible for explaining variation in the response variable. In the current work, we investigated three related multivariate techniques: Principal Component Regression (PCR), Partial Least Squares or Projections to Latent Structures (PLS), and Orthogonal Partial Least Squares (OPLS). To perform a comparative analysis, we used a publicly available dataset for Parkinson’ disease patien ts. We first performed the analysis using a cross-validated number of principal components for the aforementioned techniques. Our results demonstrated that PLS and OPLS were better suited than PCR for identifying the discriminatory predictors. Since the X data did not exhibit a strong correlation, we also performed Multiple Linear Regression (MLR) on the dataset. A comparison of the top five discriminatory predictors identified by the four techniques showed a substantial overlap between the results obtained by PLS, OPLS, and MLR, and the three techniques exhibited a significant divergence from the variables identified by PCR. A further investigation of the data revealed that PCR could be used to identify the discriminatory variables successfully if the number of principal components in the regression model were increased. In summary, we recommend using PLS or OPLS for hypothesis generation and systemizing the selection process for principal components when using PCR.rewordexplain later why MLR can be used on a dataset with no correlation

The paper presents the problem of damage detection in steel girders. Static displacements at the selected point of the structure play the role of measured variables. Structural response signal decomposition is performed according to the Mallat pyramid algorithm, which is used to perform the discrete wavelet transform (DWT). This procedure allows us to quite well determine the location of structural damage. The geometry and the placement of any defective part of the structure may have a random character. It can be assumed that the random processes occurring in the broadly understood structure mechanics are Gaussian in nature. The first four probabilistic moments are estimated using three approaches independent: semi-analytical (SAM), perturbative (SPT), and Monte-Carlo simulations (MCS). The semi-analytical random approach seems to be the most optimal due to the necessary computation time. The incorporation of the mathematical stochastic apparatus into the classical (deterministic) analysis of the statics of the structure makes it possible to estimate the reliability measures of the analyzed girder.

Previous high throughput screening studies indicated trans-eQTLs tend to be tissue specific. In this study, I probed if this feature can be used to identify tissue-specific gene regulatory networks. eQTL data (P<5e-8) for 16,259 genes were identified and their summary association statistics were obtained from the eQTLGene database. Next, eQTLs that display both cis and trans regulatory effects were selected and the association between their corresponding genes were examined using Mendelian randomization. A total of 169 genes that exerted trans-regulatory impacts on 692 genes were identified. 90% of the genes (N=749) aggregated into a gene regulatory network significantly enriched in hemo-immune processes. The robustness of finding was confirmed through simulation. The identified network displayed the scale-free topology. This provided the reason to examine the association of the network’s hub genes with the phenome. The outcome of analyses revealed GSDMB and ORMDL3 impact several disorders of immune origin and ALDH2 overexpression contributes to obesity. This study reports trans-eQTLs can be used to identify tissue-specific gene regulatory networks and describes a workflow to achieve this purpose. The network identified in this study showed scale-free topology indicating the hub genes of a GRN could be targeted to prevent disease outcomes.

An orthogonal pore ('orthopore') is conceptually based on an electrolytic cell with a standard pore (the main or 'longitudinal' pore) between cis and trans compartments filled with electrolyte and augmented by a secondary or 'transverse' pore in the form of a channel that is perpendicular to and intersects the main pore. Orthopores can be designed at different scales: macro through micro to nano. With nano-sized pores an analyte (polymer) can be threaded through the main pore and exposed at the junction to electrolyte flow through the secondary pore. Polymer translocation speeds are then independent of the current measured, which can be of an arbitrary magnitude even with the polymer stationary. Orthopores have a wide range of potential applications, including polymer (DNA and protein) sequencing, DNA unzipping, logic circuitry, and protein identification. The present report shows how orthopores can be used to implement boolean logic.

The aim of this paper is to establish a valid procedure for better understanding all the phenomena associated with the high-speed machining of Glass Fibre Reinforced Plastic (GFRP) composites. Both rectangular and circular specimens were machined at high speeds (up to 50 m/min) in order to understand what occurred for all values of fiber orientation angles during machining operations. An innovative testing methodology was proposed and studied to investigate the phenomenon of burr formation and thus understand how to avoid it during machining operations. To this end, the forces arising during the machining process and the roughness of the resulting surface, were carefully studied and correlated with the cutting angle. Additionally, the cutting surface and chip morphology formed during cutting tests were examined using a high-speed camera. Close correlations are found between the variations of the cutting forces' signals and the trends of the roughness and the morphology of the machined surface.

The effectiveness of a hybrid technique for identifying seismic damage in planar, multistory, steel X or V-braced frames is demonstrated here through an example of a six-story frame. This proposed technique, referred to as “M and P”, combines the instrumental Monitoring (M) with Pushover analysis (P). According to the methodology, the diagram of stepping eigenfrequencies of the frame in the inelastic region is initially plotted against seismic roof displacement. The fundamental natural frequency detected via the monitoring process is then utilized in this key diagram to reveal the inelastic roof displacement that corresponds to the damage state of the steel braced frame. This displacement is subsequently used as the target in the pushover analysis, facilitating the identification of seismic damage in the existing steel braced frame. Finally, the damage image is correlated with the damage stiffness matrix of the frame at the same inelastic roof displacement. The investigation results indicate that combining instrumental monitoring with pushover analysis enables accurate identification of seismic damage potential in existing steel braced frames.

The article deals with auxetic structures made on the basis of suitably connected rigid rotating squares (from Grima and Evans), with axes of rotation on the squares’ surface. The geometric model and the resulting relationships that allow for the determination of Poisson’s ratio are considered in detail. It is demonstrated that changing the rotation axis position does not affect the negative Poisson’s ratio, equal to -1. The models built confirm the initial considerations and can offer new application possibilities.

As matrix representations of magic labelings of related hypergraphs, magic squares and their various variants have been applied to many domains. Among various subclasses, trimagic squares have been investigated for over a hundred years. The existence problem for trimagic squares with singly even orders and orders 16n has been solved completely. However, very little is known for the existence of trimagic squares with other even orders except for the only three examples and three families. We construct normal trimagic squares by using product constructions, row-square magic rectangles, and trimagic pairs of orthogonal diagonal Latin squares. We give a new product construction: For positive integers p, q, and r having the same parity other than 1, 2, 3, 6, if normal p × q and r × q row-square magic rectangles exist, then a normal trimagic square with order pqr exists. As its application, we construct normal trimagic squares of orders 8q^3 and 8pqr for all odd integers q not less than 7 and p,r ∈ {7, 11, 13, 17, 19, 23, 29, 31, 37}. Our construction can easily be extended to construct multimagic squares.

A new model for international bed numbers is applied to local area populations for English Clinical Commissioning Groups (CCGs) where the Age Standardized Mortality Rate (ASMR) is used as a measure of population health and hence for total occupied hospital bed demand (elective plus emergency admission types, including acute, rehabilitation, mental health, and maternity), rather than simple bed availability. A 100-unit increase in ASMR (European Standard population) leads to a 15.3 – 30.7 (feasible range) unit increase in occupied beds per 1,000 deaths. ASMR shows why the Australian states of the Northern Territory and Tasmania have an intrinsic higher bed demand than the other states – although in both cases the bed planning methodologies failed to indicate this need and both states show a large bed deficit. Due to the high volatility in bed demand the average bed demand for 2019 was determined by a linear trend using data for 2014/15 to 2019/20 — as the pre-COVID-19 baseline. The slope of the relationship between occupied beds per 1,000 deaths and deaths per 1,000 population shows a power law function. As is to be expected there is scatter around the trend line which will partly arise from uncertainty in the expected occupied beds in 2019, fluctuations in both ASMR and deaths per 1,000 population from one year to another, changes in the number of persons on the elective, outpatient and diagnostic waiting lists, and local area variation in births and consequently upon maternity, neonatal and pediatric bed demand. Additional variation in bed demand will arise from differences in the level of funding for social care, especially elderly care, and to a lesser extent upon patients using private health care, and charitable hospices for palliative care. However, after including the change in bed demand arising from ASMR the model is sufficiently accurate to identify gross differences in bed demand as a prelude to further investigation. The model requires further extension to cover specialty-level demand, and perhaps segregation between elective and emergency types of inpatient demand. A method for benchmarking the whole hospital’s average bed occupancy is given which enables them to run at optimum efficiency and safety. Using this method English hospitals can be shown to operate at highly disruptive and unsafe levels of bed occupancy leading to deleterious ‘turn-away’. Turn-away implies bed unavailability for the next arriving patient. The problems associated with crafting effective bed planning are illustrated using the English NHS as an example.

We introduce the notion of generalized contraction on dualistic partial metric spaces. A fixed point theorem for mappings satisfying above mentioned contraction is obtained. Some consequences of our result are obtained. We construct an example to demonstrate the effectiveness of our result among the corresponding results in partial metric spaces. Our results provide substantial generalizations and improvements of several well known results existing in the comparable literature. We discuss an application of our fixed point results to show the existence of solution of functional equations.

This study explores fault-tolerant consensus in leader-following heterogeneous multi-agent systems, focusing on actuator failures in uncrewed aerial vehicles (UAVs) and uncrewed ground vehicles (UGVs). An optimization-based fault-tolerant consensus algorithm is proposed. The algorithm utilizes the Euler-Lagrange formula to ensure system consistency under actuator failures, with the Lyapunov stability theory proving the asymptotic stability of the consistency error. The algorithm is applied to heterogeneous multi-agent systems of UAVs and UGVs to derive optimal fault-tolerant consensus control laws for each vehicle type. Simulation experiments give evidence for the feasibility of the proposed control strategy.

Due to an urgent need for reducing the fast progressing climate changes, a rapid, standardized and replicable solution for the infrastructure restructuring of heat demand coverage of buildings at district and city level must be developed. As more and more communities in Europe, especially in Germany, are obligated to have plans for coverage of heat demand, city planners, energy agencies seek a tool, which will help them to design the first drafts of heating network routes, which can supply whole districts and cities with renewable energy. ArcGIS Pro Tools like Least-Cost-Path-Analysis (LCPA) and Closest Facility (CF) allow to find the shortest and “cheapest” way between the heat source and heat consumers in the analyzed areas. Starting from the community level, through the district, county, voivodeship and whole country levels, the replication of the methods for generating district heating (DH) network infrastructure can be achieved. The proposed LCPA and CF based methods help to design the most suitable and efficient DH networks in the analyzed areas. As only few open-source data input, like street networks and building footprints are needed, the methods can be implemented in all communities of the country of Poland. In this paper one example of one community of Wroclaw county, called Siechnice and surroundings is presented.

The accurate detection of clouds is an important first-step in the processing of remotely sensed satellite data analyses and subsequent cloud model predictions. While initial cloud retrieval technology began with the exploitation of one or two bands of satellite imagery, it has accelerated rapidly in recent years as sensor and retrieval technology have exploded, creating a new era in space exploration. Additionally, initial emphasis in satellite retrieval technology focused on cloud detection for cloud forecast models, more recently cloud screening in satellite acquired data is playing an increasingly critical role in the investigation of cloud free data for the retrieval of soil moisture, vegetation cover, ocean colour concentration and sea surface temperatures, as well as environmental monitoring of a host of products, e.g. atmospheric aerosol data, to study the Earth’s atmospheric and climatic systems. With about 60% of the Earth covered by clouds, on average, it is necessary to both accurately detect clouds in remote sensing data to screen cloud contaminate data in remote sensing analyses. In this paper, the evolution of cloud detection technology is highlighted with advancement in sensor hardware technology and possible AI algorithmic advances. Additionally, a discussion is presented on methods to obtain the cloud truth data needed to determine the accuracy of these cloud detection approaches.

In today’s rapidly evolving digital landscape, the significance of password guessing techniques in both offensive and defensive strategies is paramount. Passwords serve as a crucial line of defense for both individuals and corporations, safeguarding their sensitive systems and data. Therefore, assessing the effectiveness of these access credentials is a critical task. However, existing research in this field often encounters limitations, such as a lack of sufficient training data and extended model training times. Current methods often struggle with limited training data and lengthy training times. This paper introduces BBPE-AE, a novel Auto Encoder Network (AE) designed for password guessing. BBPE-AE utilizes Byte-level Byte Pair Encoding (BBPE) to extract frequent tokens from password datasets without length restrictions, employing a dynamic window technique to capture complex patterns. Experimental results on Hotmail and Myspace datasets demonstrate exceptional performance, achieving high similarity rates (BLEU-Unigram: 0.90, BLEU-Bigram: 0.82 for Hotmail; BLEU-Unigram: 0.90, BLEU-Bigram: 0.81 for Myspace). BBPE-AE generates realistic passwords that meet HIBP (Have I Been Pwned) standards, minimizing duplication. These findings highlight the effectiveness of BBPE-AE in enhancing security by generating realistic passwords, ultimately safeguarding sensitive systems and data.

The paper delves into the critical issue of damage detection within the guy cable of a truss steel mast, a pivotal component in structural integrity. It introduces a model wherein damage manifests as a localized cross-section reduction in a single element of the cable. Employing Discrete Wavelet Transform (DWT), a pioneering methodology, the study scrutinizes the behavior of the affected elements through static structural analyses. Signal decomposition via the Mallat pyramid algorithm facilitates comprehensive examination. Static displacements at the connection point between the cable and the truss mast serve as the measured variables. Through systematic investigation, the paper evaluates the impact of damage size and location, external loading force, and cable tension force on the efficacy of the proposed approach. Utilizing data derived from Finite Element Method (FEM) computations for wavelet analysis the authors substantiate the findings with numerical examples, thus offering valuable insights into damage detection strategies for structural health monitoring and engineering applications.

Orthogonal operators can successfully be used to calculate eigenvalues and eigenvector compositions in complex spectra. Orthogonality ensures least correlation between the operators and thereby more stability in the fit, even for small interactions. The resulting eigenvectors are used to transform the pure transition matrix into realistic intermediate coupling transition probabilities. Calculated transition probabilities for close lying levels illustrate the power of the complete orthogonal operator approach.

Objective. To test the hypothesis that a session of unilateral tSMS over the dominant primary motor cortex (M1) in healthy subjects produces a transient decrease in manual dexterity. Methods. A triple-blinded randomized control trial was conducted in 40 healthy participants who were allocated to real- or sham-tSMS group. Each participant underwent one session of tSMS and were assessed before, immediately after, 15 minutes, and 40 minutes after stimulation. Outcome measures were Finger Tapping Test (FTT), 5-seconds FTT, nine Hole Peg Test, and the hand grip assessment. Results: Significant differences were found between groups 15 minutes after stimulation in favor of the tSMS group in the FTT (2.2 ± 0.99; CI= .18-4.22; d= .84p=.034), and 5-second FTT (4.2 ± 1.98; CI= .199-8.2, d= .68; p=.04). In the intragroup analysis, a significantly lower number of taps 15 minutes after stimulation was observed in sham group (3.3 ± 1.01; CI= .47-6.13; d= .42; p=.015), but not in the real stimulation group. Conclusion: A unilateral session of tSMS in the M1 of the dominant hemisphere of healthy individuals does not reduce manual dexterity or grip strength. This technique could have benefits on the motor performance of the arm contralateral to the stimulated motor cortex

Introduction: The aim of the present systematic review was to evaluate the clinical and radiographic success of partial pulpotomies in deep caries processes or post-eruptive defects in young, vital permanent teeth. Methods: Electronic databases, PubMed, Scopus, and Embase, were searched, followed by a manual search. Randomized controlled trials evaluating partial pulpo-tomy with a follow-up period of ≥12 months were included. Meta-analyses using a random effect model were performed. Results: A total of 3.127 articles were retrieved, and after duplicate re-moval, 2.642 were screened by title and abstract; 1 additional article was found during the manual search in the reference lists, and 79 were identified. Finally, 6 papers were included in the review. Regardless of the partial pulpotomy modalities or material used, there were no signifi-cant differences between clinical and radiographic success rates (cumulative success rate 91,8%-92,3%, respectively). Five studies were included in the meta-analysis that did not indicate any statistically significant differences in success rates when Mineral Trioxide Aggregate was compared to other materials (95% CI 0,239 to 1,016 p=0.055). Conclusion: This research system-atically evaluates the evidence and summarises the available data on partial pulpotomy in young permanent teeth. Given its high clinical and radiographic success rate, partial pulpotomy should be considered when vital pulpal therapy needs to be performed in highly damaged young per-manent teeth, as this procedure provides a biological benefit and allows more invasive endodon-tic treatments to be postponed.

In the paper, the authors consider the generating functions of the Hermite polynomials and their squares, present explicit formulas for higher order derivatives of the generating functions of the Hermite polynomials and their squares, which can be viewed as ordinary differential equations or derivative polynomials, find differential equations that the generating functions of the Hermite polynomials and their squares satisfy, and derive explicit formulas and recurrence relations for the Hermite polynomials and their squares.

This study presents an innovative approach for the utilization of industrial by-products and municipal waste in the production of sustainable and environmentally friendly cement mortar. We explored stabilized stainless-steel reduced slag (SSRS) and polyethylene (PE) plastic waste as partial replacements for aggregates. Various engineering properties of the resulting cement mortar specimens, including slump, slump flow, compressive strength, flexural strength, tensile strength, water absorption, and ultrasonic pulse velocity (UPV), were investigated through comprehensive experimental tests. The influence of different water-cement (w/c) ratios and substitution amounts on the engineering properties of the cement mortar samples was thoroughly examined. The findings revealed that an increase in PE substitution adversely affected the overall workability of the cement mortar mixtures, whereas an increase in SSRS amount contributed to enhanced workability. As for the hardened properties, a consistent trend was observed for both cases, with higher w/c ratios and substitution amounts leading to reduced mechanical properties. Water absorption and UPV test results validated the increased formation of porosity with higher w/c ratios and substitution amounts. This study proposes a promising method to effectively repurpose industrial by-products and municipal wastes, transforming them into sustainable construction and building materials. Additionally, a comparative analysis of transportation costs and carbon footprint emissions between SSRS-cement mortar and PE-cement mortar was conducted to assess their environmental impact and sustainability. Generally, higher w/c ratios and replacement levels corresponded to reduced carbon footprint. The geographical location of the source of SSRS and PE remains a challenge and studies to overcome this challenge must be further explored.

The increase in life expectancy, according to the World Health Organization, is a fact, and with it rises the incidence of age-related neurodegenerative diseases. The most recurrent symptoms are those associated with tremors resulting from Parkinson's Disease (PD) or Essential Tremors (ET). The main alternatives for the treatment of these patients are medication and surgical intervention, which sometimes have restrictions and side effects. Through computer simulations in Matlab software, this work investigates the performance of adaptive algorithms based on least mean squares (LMS) to suppress tremors in upper limbs, especially in the hands. The signals resulting from pathological hand tremors, related to PD, present components at frequencies that vary between 3~Hz and 6~Hz, with the more significant energy present in the fundamental and second harmonics, while physiological hand tremors, referred to as ET, vary between 4~Hz and 12~Hz. We simulated and used these signals as reference signals in adaptive algorithms, Filtered-x Least Mean Square (Fx-LMS), Filtered-x Normalized Least Mean Square (Fx-NLMS), and a hybrid Fx-LMS\&NLMS purpose. Our results showed that the vibration control provided by the Fx-LMS\&LMS algorithm is the most suitable for physiological tremors. For pathological tremors, we have used a proposed algorithm with a filtered sinusoidal input signal, Fsinx-LMS, which presented the best results in this specific case.

The Solvency II regulatory framework specifies procedures and parameters for determining solvency capital requirements (SCRs) for insurance companies. The proposed standard SCR calculations involve two steps. The Value–at–Risk (VaR) of each risk driver is measured and, in a second step, all components are aggregated to the company’s overall SCR, using the Standard Formula. This formula has two inputs: the VaRs of the individual risk drivers and their correlations. The appropriate calibration of these input parameters has been the purpose of various Quantitative Impact Studies that have been conducted during recent years. This paper demonstrates that the parameter calibration for the equity–risk module—overall, with about 25%, the most significant risk component—is seriously flawed, giving rise to spurious and highly erratic parameter values. As a consequence, an implementation of the Standard Formula with the currently proposed calibration settings for equity–risk is likely to produce inaccurate, biased and, over time, highly erratic capital requirements.

To decrease oral pathogens and increase the number of beneficial bacteria, probiotics and bioactive compounds made via microbial bioconversion are recently used. In addition, the interest regarding probiotics-mediated bioconversion with popular medicinal plants is increasing. These compounds produced during the process exhibit synergistic effect and enhance a variety of biological activities including pathogen inhibition in host. Therefore, we developed bioconverted milk with high inhibitory activity against oral pathogens and α-glucosidase. Lactiplantibacillus plantarum SMFM2016-RK was chosen as the probiotic due to its beneficial characteristics such as high acid and bile tolerance, antioxidant activity, and α-glucosidase inhibition. Based on the minimal bactericidal concentration against three oral pathogens, the following appropriate concentrations of Artemisia herba-alba extract were added to milk: 5 mg/mL of A. herba-alba ethanol extract and 25 mg/mL of A. herba-alba hot-water extract. Four bioconverted milks (BM), BM1, BM2, BM3, and BM4, were produced by combining L. plantarum SMFM2016-RK alone, L. plantarum SMFM2016-RK and ethanol extract, L. plantarum SMFM2016-RK and hot-water extract, and L. plantarum SMFM2016-RK with both extracts. As a result of antimicrobial activity, BM3 inhibited the growth of Aggregatibacter actinomycetemcomitans and Porphyromonas gingivalis the most, and BM4 suppressed the growth of Fusobacterium nucleatum the most. In addition, bioconverted milk containing A. herba-alba (BM2, BM3, and BM4) inhibited α-glucosidase more effectively than BM1. In conclusion, A. herba-alba-added milk bioconverted by L. plantarum SMFM2016-RK displayed the growth inhibitory effect on oral pathogens and the α-glucosidase inhibitory activity, thus it necessitates to evaluate the effects on the alleviation of oral diseases and glycemic control through future animal experiments.

In the present paper we introduce the concept of orthogonal frames in Krein spaces, prove the independence of the choice of the fundamental symmetry, and from this we obtain a number of interesting properties that they satisfy. We show that there is no distinction between orthogonal frames in a Krein space and orthogonal frames in its associated Hilbert. Furthermore, we characterize frames dual to a given frame, which is a useful tool for constructing examples.

The technique of obtaining information or data about any feature or object from afar, called in technical parlance as remote sensing, has proven extremely useful in diverse fields. In the ecological sphere, especially, remote sensing has enabled collection of data or information about large swaths of areas or landscapes. Even then, in remote sensing the task of identifying and monitoring of different water reservoirs has proved a tough one. This is mainly because getting correct appraisals about the spread and boundaries of the area under study and the contours of any water surfaces lodged therein becomes a factor of utmost importance. Identification of water reservoirs is rendered even tougher because of presence of cloud in satellite images, which becomes the largest source of error in identification of water surfaces. To overcome this glitch, the method of the shape matching approach for analysis of cloudy images in reference to cloud-free images of water surfaces with the help of vector data processing, is recommended. It includes the database of water bodies in vector format, which is a complex polygon structure. This analysis highlights three steps: First, the creation of vector database for the analysis; second, simplification of multi-scale vector polygon features; and third, the matching of reference and target water bodies database within defined distance tolerance. This feature matching approach provides matching of one to many and many to many features. It also gives the corrected images that are free of clouds.

Alpha emitters like plutonium pose severe health risks when ingested, damaging DNA and potentially causing cancer. Traditional detection methods require proximity within millimeters of the contamination source, presenting safety risks and operational inefficiencies. Long-range detection through alpha radioluminescence (RL) offers a promising alternative. However, most of the previous experiments have been carried out under controlled conditions that preclude the overwhelming effect of ambient light. This study demonstrates successful detection of a 3 MBq alpha emitter in an open environment using a newly developed, lightweight compact alpha camera. This camera incorporates a deep-cooled CCD and a specially designed lens system with a low f-number to maximum the signal intensity. The lens was also designed to minimize blue shift effects of filters. Nighttime imaging was achieved with a dual-filter system using a sandwich filters assembly centered at 337 nm and 343 nm for capturing alpha RL and subtracting background light, respectively. At night, the alpha source was detected from 1 meter away within one minute. The system was also evaluated under simulated urban lighting conditions. For daytime imaging, a stack of tilted 276 nm short pass filters minimized sunlight interference, enabling clear detection of the alpha source at 70 cm within 10 minutes under indirect sunlight. This research not only underscores the viability of long-range optical detection of alpha emitters for environmental monitoring and scientific research but also highlights its ability to enhance nuclear safety and public health in real-world settings.

In this paper, we present a new concept of the generalized core orthogonality (called the C-S orthogonality) for two generalized core invertible matrices $A$ and $B$. $A$ is said to be C-S orthogonal to $B$ if $A^{\tiny\textcircled{S}}B=0$ and $BA^{\tiny\textcircled{S}}=0$, where $A^{\tiny\textcircled{S}}$ is the generalized core inverse of $A$. The characterizations of C-S orthogonal matries and the C-S additivity are also provided. And the connection between the C-S orthogonality and C-S partial order has been given using their canonical form. Moreover, the concept of the strongly C-S orthogonality is defined and characterized.

This paper provides orthogonal moments (OM) such as, Zernike Moments(ZM), Psuedo Zernike Moments(PZM) and Orthogonal Fourier Mellin Moments(OFMM) for the analysis of melanoma images. The moment invariants may vary with respect to geometric variations. For the analysis of orthogonal moments hundred random melanoma images and hundred non-melanoma images have been taken into consideration from the database of 570 melanoma images and 250 non-melanoma images respectively. Orthoganal moments have been computed by varying the phase angles from 10° to 40° with an equal interval of 10° degree for the orders 2, 4,8,16,32,64,128,256 respectively. For the optimal OMs Particle Swarm Optimization (PSO) technique have been used. These set of extracted optimal OMs have been further applied to classify melanoma images. Support Vector Machine (SVM) has been used for the classification of [1]sensitivity=88.78%.

Partial Differential Equations (PDEs) constitute a fundamental framework for modeling various physical phenomena across diverse fields such as physics, engineering, and finance. Solving PDEs accurately and efficiently remains a significant challenge, particularly when dealing with complex systems or high-dimensional data. In this paper, we present a novel approach based on deep learning techniques to investigate the effective factors in solving PDEs. Our methodology leverages the expressive power of deep neural networks to learn and represent the underlying relationships between input parameters and the solutions of PDEs. By incorporating domain knowledge into the network architecture and training process, our approach aims to provide insights into the key factors influencing the solution of PDEs. We demonstrate the effectiveness of our method through numerical experiments on various PDEs, showcasing its capability to identify important features and improve predictive accuracy. Our findings suggest that deep learning techniques offer a promising avenue for understanding and analyzing the complex dynamics inherent in PDEs, paving the way for enhanced computational methods in scientific and engineering applications.

Accurate forecasting of icing thickness has a great significance for ensuring the security and stability of power grid. In order to improve the forecasting accuracy, this paper proposes an icing forecasting system based on fireworks algorithm and weighted least square support vector machine (W-LSSVM). The method of fireworks algorithm is employed to select the proper input features with the purpose of eliminating the redundant influence. In addition, the aim of W-LSSVM model is to train and test the historical data-set with the selected features. The capability of this proposed icing forecasting model and framework is tested through the simulation experiments using real-world icing data from monitoring center of key laboratory of anti-ice disaster, Hunan, South China. The results show that the proposed W-LSSVM-FA method has a higher prediction accuracy and it may be a promising alternative for icing thickness forecasting.

The behaviour and bifurcations of solutions to three-dimensional (three-phase) quadratic polynomial dynamical systems (DSs) are considered. The integrability in elementary functions is proved for a class of autonomous polynomial DSs. The occurrence of bifurcations of the type twisted fold is discovered on the basis and within the frames of the elements of the developed DS qualitative theory. The discriminant criterion applied originally to two-phase quadratic polynomial DSs is extended to three-phase DSs investigated in terms of their coefficient matrices. Specific classes of D- and S-vectors are introduced and complete description of the symmetry relations inherent to the DS coefficient matrices is performed using the discriminant criterion.

This study analyses regional development in one of the poorest provinces in China, Guizhou Province, between 2000 and 2012 using a multiscale and multi-mechanism framework. In general, regional inequality has been declining since 2000. In addition, economic development in Guizhou Province presented spatial agglomeration and club convergence, which shows how the development pattern of one core area, two-wing areas and a contiguous area at the edge of the province have been developed between 2006 and 2012. Multilevel regression analysis revealed that industrialization and investment level were the primary driving forces of regional economic disparity in Guizhou Province. The influences of marketization and decentralization on regional economic disparity were relatively weak. Investment level reinforced regional economic disparity and the development of core-periphery structure in the province. However, investment level actually weakened the regional economic disparity in Guizhou Province when the variable of time was considered. In addition, both the topography and urban–rural differentiation were the two main reasons for forming a core-periphery structure in Guizhou Province.

This paper reveals some properties of the cumulative entropy of consecutive k-out-of-n:F system's lifetime. First, we introduce a method for calculating the cumulative entropy of their lifetime and explore its preservation properties using established stochastic orders. Ad- ditionally, we obtain useful bounds that can used in situations where the distribution function of the system's component lifetimes are complicated or systems have large components. To support practical applications, we present two nonparametric estimators for the cumulative entropy of these systems. The efficiency and performance of these estimators are illustrated with simulated datasets and further validated with real data sets.

Rationale: Post-hepatectomy liver failure (PHLF) remains a significant risk for patients undergoing partial hepatectomy (PHx). Reliable prognostic markers and treatments to enhance liver regeneration are lacking. Plasma nanoparticles, including lipoproteins, exosomes, and extracellular vesicles (EVs), can reflect systemic and tissue-wide proteostasis and stress, potentially aiding liver regeneration. However, their role in PHLF is still unknow. Methods: Our study included 9 patients with hepatocellular carcinoma (HCC) undergoing PHx: 3 patients with PHLF, 3 patients undergoing the Associating Liver Partition and Portal vein Ligation for Staged hepatectomy (ALPPS) procedure and three matched controls without complications after PHx. Patient plasma was collected before (PRE), 1 and 5 days (POD1, POD5) after PHx. EVs were isolated by ultracentrifugation and extracted proteins subjected to quantitative mass spectrometry using a super-SILAC mix prepared from primary and cancer cell-lines. Results: We identified 2625 and quantified 2570 proteins in EVs in PHx patients. Among these, 53 proteins were significantly upregulated and 32 were downregulated in patients with PHLF compared to those without PHLF. Furthermore, 110 proteins were upregulated and 78 were downregulated in PHLF compared to patients undergoing ALPPS. The EV-proteomic signature in PHLF indicates significant disruptions in protein translation, proteostasis, intracellular vesicle biogenesis, as well as alterations in proteins involved in extracellular matrix (ECM) remodeling, metabolic and cell cycle pathways, present already before PHx. Conclusion: Longitudinal proteomic analysis of EV´s circulating in human patient plasma undergoing PHx uncovers proteomic signatures associated with PHLF which reflect dying hepatocytes and endothelial cells and are present before PHx already. Our results support EVs as potential biomarkers and therapeutic targets for liver regeneration and failure.

Using an algebraic method for solving the wave equation in quantum mechanics, we encountered a new class of orthogonal polynomials on the real line. One of these is a four-parameter polynomial with a discrete spectrum. Another that appeared while solving a Heun-type equation has a mix of continuous and discrete spectra. Based on these results and on our recent study of the solution space of an ordinary differential equation of the second kind with four singular points, we introduce a modification of the hypergeometric polynomials in the Askey scheme. Up to now, all of these polynomials are defined only by their three-term recursion relations and initial values. However, their other properties like the weight function, generating function, orthogonality, Rodrigues-type formula, etc. are yet to be derived analytically. This is an open problem in orthogonal polynomials.

The number of physical devices connected to the Internet such as vehicles, household appliances and other "things" has been steadily increasing in recent years, thus forming the basis for the Internet of Things (IoT). IoT ecosystem extends beyond country borders and application domains, combining thousands of versatile devices that differ in terms of their structures, capabilities, and available resources. It is therefore not surprising that the landscape of wireless communication technologies and the degree of IoT devices available today is excessively broad and diverse. Interference between networks leads to frame collisions and consequent packet loss. Frame collisions occur when two or more packets overlap in time and frequency and use the same Long Range (LoRa) parameters, i.e. the same Spreading Factor (SF), Bandwidth (BW) and Carrier Frequency (CF). When most devices use the same configuration, collision probability is higher. The probability of frame collisions is also affected by traffic characteristics, particularly the periodicity of the transmission and the payload size. Larger payload sizes and more frequent transmissions accumulate with higher Time on Air (ToA) and channel occupancy [1]. Transmission powers and the location of the gateways also influences this situation. The aim of this experimental work is to verify the effects of collisions and interference in Long Range Wide Area Network (LoRaWAN), regarding the periodicity of transmissions and the payload sizes in a context of an inter-SF interference scenario. And to validate measuring tools like Received Signal Strength Indicator (RSSI), ToA and Packet Delivery Ratio (PDR) in the reliability of a network. We validate our conclusions by analyzing ToA according with RSSI and different data sizes, the RSSI for different SFs and different data sizes and finally the packet loss through the PDR for a better understanding of the reliability of packet transmission in our link. In the end we conclude that in an environment with inter-SF interference, the choice of SFs and packet lengths impacts ToA. When dealing with multiple devices near gateways, different SFs and varying packet lengths can lead to increased latency and longer ToA. Consequently, the risk of packet loss becomes more significant, especially if the signal-to-interference ratio (SIR) is low. This limitation will therefore affect scalability, particularly in Non-Line-Of-Sight (NLOS) scenarios.

This paper investigates an Energy Neutral System using Micro Energy Harvesters for a Health Monitoring Wireless Sensor Node (HM-WSN). We have implemented HM-WSN consisting of a solar cell energy harvester, a Power Management Unit (PMU) and the ucontroller, sensor and transmitter acting as load. A battery extender and a switching logic circuit for sensor node is designed to evaluate the efficiency of the proposed system. The HM-WSN senses body temperature with improvement in lifetime of coincell. The HM-WSN is built using commercially available off the shelf (COTS components and consumes 47.2uW for data being updated every 134s. It can be operated for approximately 1.32 years only on a coincell. Furthermore, the HM-WSN can be operated with solar energy at 200lux, achieving 96.36 years with a combination of a coincell with an additional capacitor of 2.2mF. It attains 4.07 years to 16.87 years lifetime with the load capacitor varying from 1mF to 1.5mF at 350lux lighting condition. With the same ambient condition and a 2mF load capacitor, HM-WSN attains complete energy autonomy.

In conventional Federated Learning (FL), clients work together to train a model managed by a central server, intending to speed up the learning process. However, this approach imposes significant computational and communication burdens on clients, particularly with complex models. Additionally, while FL strives to protect client privacy, the server's access to local and global models raises security concerns. To address these challenges, Split Learning (SL) separates the model into parts handled by the client and the server, though it suffers from inefficiencies due to sequential client participation. To overcome these issues, SplitFed Learning (SFL) was proposed, which combines the parallelism of FL with the model-splitting strategy of SL, enabling simultaneous training by multiple clients. Our main contribution is the theoretical analysis of SFL, which, for the first time, includes non-i.i.d. datasets, non-convex loss functions, and both full and partial client participation. We provide convergence proofs for a state-of-the-art SFL algorithm based on conventional convergence analysis assumptions for FL. Our results prove that we can recover the linear convergence rate of conventional FL for the SFL algorithm with the distinction that increasing the number of local steps or clients may not speed up the convergence in SFL.

Embryonic development proceeds through a series of differentiation events. The mosaic version of this process (binary cell divisions) can be analyzed by comparing early development of Ciona intestinalis and Caenorhabditis elegans. To do this, we reorganize lineage trees into differentiation trees using the graph theory ordering of relative cell volume. Lineage and differentiation trees provide us with means to classify each cell using binary codes. Extracting data characterizing lineage tree position, cell volume, and nucleus position for each cell during early embryogenesis, we conduct several statistical analyses, both within and between taxa. We compare both cell volume distributions and cell volume across developmental time within and between single species and assess differences between lineage tree and differentiation tree orderings. This enhances our understanding of the differentiation events in a model of pure mosaic embryogenesis and its relationship to evolutionary conservation. We also contribute several new techniques for assessing both differences between lineage trees and differentiation trees, and differences between differentiation trees of different species. The results suggest that at the level of differentiation trees, there are broad similarities between distantly related mosaic embryos that might be essential to understanding evolutionary change and phylogeny reconstruction. Differentiation trees may therefore provide a basis for an Evo-Devo Postmodern Synthesis.

Densely urbanized areas, with a low percentage of green vegetation, are highly exposed to Heat Waves (HW) which nowadays are increasing in terms of frequency and intensity also in the middle-latitude regions, due to ongoing Climate Change (CC). Their negative effects may combine with those of the UHI (Urban Heat Island), a local phenomenon where air temperatures in the compact built up cores of towns increase more than those in the surrounding rural areas, with significant impact on the quality of urban environment, on citizens health and energy consumption and transport, as it has occurred in the summer of 2003 on France and Italian central-northern areas. In this context this work aims at designing and developing a methodology based on aero-spatial remote sensing (EO) at medium-high resolution and most recent GIS techniques, for the extensive characterization of the urban fabric response to these climatic impacts related to the temperature within the general framework of supporting local and national strategies and policies of adaptation to CC. Due to its extension and variety of built-up typologies, the municipality of Rome was selected as test area for the methodology development and validation. First of all, we started by operating through photointerpretation of cartography at detailed scale (CTR 1: 5000) on a reference area consisting of a transect of about 5x20 km, extending from the downtown to the suburbs and including all the built-up classes of interest. The reference built-up vulnerability classes found inside the transect were then exploited as training areas to classify the entire territory of Rome municipality. To this end, the satellite EO HR (High Resolution) multispectral data, provided by the Landsat sensors were used within a on purpose developed "supervised" classification procedure, based on data mining and “object-classification” techniques. The classification results were then exploited for implementing a calibration method, based on a typical UHI temperature distribution, derived from MODIS satellite sensor LST (Land Surface Temperature) data of the summer 2003, to obtain an analytical expression of the vulnerability model, previously introduced on a semi-empirical basis.

Solar photovoltaic (PV) generation suffers from multiple serious issues, for example shading effects directly affect the performance of installed PV arrays. By studying these issues, it can play a key role in improving the limitations and performance of PV panels. The study of PV arrays under partial shading conditions is mentioned in many papers as a part of other studies and as an independent phenomenon. Therefore, it is essential to improve these studies and update them with new research and study this problem in detail to know how to limit the effects of partial shading irradiance conditions on PV arrays performances, including economical aspects. This paper proposes to study the effects of different partial shading irradiance conditions for a PV array in various configurations. The analysis is proved in detail through the simulation of the proposed PV array in the Matlab/Simulink environment. The obtained results show the performances of interconnected PV arrays under different partial shading irradiance and temperature conditions, including the solar array I-V and P-V characteristics. In addition, different PV array configurations with and without bypass and blocking protection diodes improve and minimize the effect of partial shading conditions and avoid the reductions in output power.

Introduction: Novel robotic surgery systems (da Vinci Xi) are superior to classical open and laparoscopic techniques with its clear and three-dimensional view. We aimed to present the first case low anterior resection of rectal cancer and vaginal specimen extraction with Da Vinci Xi.Case: A 75-year-old female patient with rectum adenocarcinoma was undergone robotic-assisted low anterior resection (LAR) of the rectum, vaginal removal of the specimen, colorectal anastomosis and loop ileostomy. The operation time was 190 minutes. There were no postoperative complications. Pathological tumor stage was stage pT1N0 with negative proximal, distal and radial resection margins. The patient was discharged on the third postoperative day.Conclusion: Robot-assisted LAR, total mesorectal excision, vaginal removal of the specimen, colorectal anastomosis, and loop ileostomy can be performed easily and safely with Da Vinci Xi at early stage rectal cancer. And the vaginal extraction of the specimen avoids us from a traditional abdominal incision.

The pharmacological effects of the fruiting body of Ophiocordyceps sinensis (Os) exerted antioxidant, anti-virus, and immunomodulatory, whereas the anti-inflammatory effects and active components of Os mycelial submerged culture (OMSC) are not known. This study aimed to investigate the active compounds in the fermented liquid (FLOS), hot water (WEOS), and 50-95% (EEOS-50, EEOS-95) ethanol extracts of OMSC and their anti-inflammatory effects and potential mechanisms in LPS-stimulated microglial BV2 cells. The results demonstrated that all of the OMSC extracts could inhibit NO production in BV2 cells. EEOS-95 exhibited the strongest inhibitory effects (41 % inhibitory ability at 500 µg/mL), and its ergosterol, GABA, total phenolic, and total flavonoid contents were significantly higher than those of the other extracts (18.60, 18.60, 2.28, and 2.14 mg/g, p &lt; 0.05, respectively). EEOS-95 also has a strong inhibitory ability against IL-6, IL-1β and TNF-α with IC50 of 617, 277 and 507 µg/mL, respectively, which is higher than that of 1 mM melatonin. The anti-inflammatory mechanism of EEOS-95 seems to be associated with up-regulation of PPAR-γ/Nrf-2/HO-1 antioxidant-related expression and down-regulation of NF-κB/COX-2/iNOS pro-inflammatory expression signaling. Therefore, we hypothesized that EEOS-95 can prevent neurodegenerative diseases, but the effect on the application in vivo should be further investigated.

Despite the efforts made to stop the tuberculosis (TB) epidemic, it still remains one of the leading causes of death from an infectious disease. Previous work in the group uncovered a new family of amides which showed promising activities against Mycobacterium tuberculosis. A closer look at the literature showed that these compounds are structurally related to the DNB family of DprE1 inhibitors, so, we decided to study a wide range of substituted amides and determine their activity, focusing on unexplored structures related to the dinitrobenzamides (DNB) found in the literature. To synthesize our library of compounds we started from 3,5-dinitrobenzoic acid to form the nitroaromatic core that is characteristic of the DNB’s, to which we then added linear or cyclic amine moieties. Additionally, the impact of terminal aromatic moieties was also assessed for some derivatives, via an ether, ester, or amide bond. In order to obtain the desired derivatives, multiple synthetic approaches were used, mainly focused on nucleophilic addition/elimination reactions, SN2 reactions and Mitsunobu reactions. The activity was impacted mainly by two structural features, the addition of an aromatic moiety as a terminal group and the type of the linker. The most interesting compounds exhibited activities comparable to isoniazid and DNB1. Computational studies were also performed aimed at understanding their possible interactions with DprE1. The most active compounds are a good starting point for further development, and we plan to study an extended family of compounds based in those structures.

The processed tomato is one of the major food products of Italy and characterized today many Italian Regions, in northern and southern Italy, even though the firms in the industry have had difficulties, in recent years, due to an increase in the cost of raw materials. Furthermore, tomato processing firms are often characterized by significant investment in fixed assets and working capital, with an consequent increase in equity and/or debt financing, with consequent increasing of the risk of bankruptcy, as happens to many firms in the sector in recent years. The aim of the research is than to analyze the risk of bankruptcy of tomato processing companies applying financial ratios. To achieve this goal, the research consider the annual data of a sample of 17 tomato processing firms operating in the Inter Regional Interprofessional Organization “OI Pomodoro da Industria Nord Italia”; firms’ data are divided into still-active (not-distressed) and failed (distressed) firms, with the aim of analyzing the differences between financial data and management practices of the two groups of firms to evaluate the sustainability of the business cycle. The company data suggest that larger firms, with adequate financial structure, have been able to withstand the tomato market crisis in recent years, where distressed firms are on average smaller and suffer from a higher recourse to debt capital with lower profit margins than not-distressed firms. The research could then be applied by entrepreneurs, managers, bankers and public operator to define good practices of management to be achieved and measured with financial ratios even in order reduce the risk of distress for firms operating in tomato sector.

The partial discharge (PD) event in high voltage insulation releases energy, exerts mechanical pressure, and generates elastic waves. Detecting and locating these PD events through short-duration acoustic pulses is well-established, particularly in gas-insulated systems and oil-insulated transformers. However, its full potential remains untapped in solid insulation systems, where the propagation capability of acoustic pulse and the acoustic reflections pose fundamental challenges to the Acoustic Emission (AE) detection technique. This study investigates the influence of reflections and multiple paths on the propagating acoustic pulse in polymeric insulating materials using a finite element method (FEM) in COMSOL. It was observed that the reflections from the boundary influence the propagating pulse's shape, peak magnitude, and arrival time. An analytical MATLAB model further quantifies the impact of multiple propagation paths on the shape, magnitude, and arrival time of the pulse travelling in a cylinder. Additionally, a Perfect Matched Layer (PML) was implemented in the COMSOL model to eliminate reflections from the boundary, and it revealed that the acoustic pulse magnitude decreases with distance following the inverse square law. In essence, the models aid in measuring how reflections contribute to the observed signals, facilitating the precise identification of the source of the PD event in the tested system.

The pollution of the bays in Abidjan is a major concern for the Ivorian policy makers. In fact, the pollution of the bays induce high costs to the society while impacting population health dramatically. As a result, pollution reduction management of production activities has been undertaken in the Cocody Bay area. To our knowledge, no study has yet proposed a model to evaluate the cost-effectiveness of these pollution management strategies. A cost-effectiveness model, based on Monte Carlo simulation, was developed to assess the economic and environmental impacts of various scenarios characterized by a set of production practices, both in the short term and in the long term. The authors discuss the steps and input parameters of the model presented. The proposed model may serve as the basis for identifying an optimal production scenario defined as the scenario with the best incremental cost-effectiveness ratio considering a willingness to pay (WTP) threshold. The WTP, to be estimated based on the gross domestic product of Côte d’Ivoire, represents the opportunity costs associated with selecting the optimal scenario. The current framework can also be applied to other settings facing similar challenge.

Saltwater intrusion in the rapidly developing city of Da Nang in central Vietnam is currently causing various water-related challenges, including inadequate water supply and water pollution. An integrated SWAT-MODFLOW numerical model was used to investigate the origin and mechanism of saltwater in Holocene and Pleistocene aquifers. Geophysical and isotopic approaches were used to validate the SEAWAT model applied for simulating saltwater intrusion. The results suggest that the ebb and flow of tides, as well as water levels in rivers primarily impact coastal aquifers. However, effective water resource planning and management, along with maintaining the natural recharge of fresh water from local rain during the rainy season, could enable the rational and efficient utilization of groundwater, reducing saltwater intrusion in many areas. During the dry season, groundwater is recharged from higher altitude areas. The current saltwater intrusion mainly occurs along the rivers up to the hydraulic dam. Simulated models, using scenarios of stop abstracting groundwater, but changing to the use of surface water for drinking water, show that the area of saline water shrinks quickly after 30 years, reducing from 59.6 km2 to 39.5 km2 and from 40.2 km2 to 28.6 km2 in Holocene and Pleistocene, respectively.

In this article, we prove an orthogonal decomposition theorem for real inner product gyrogroups, which unify some well-known gyrogroups in the literature: Einstein, M\"{o}bius, Proper Velocity, and Chen's gyrogroups. This leads to the study of left (right) coset partition of a real inner product gyrogroup induced from a subgyrogroup that is a finite-dimensional subspace. As a result, we obtain gyroprojectors onto the subgyrogroup and its orthogonal complement. We construct also quotient spaces and prove an associated isomorphism theorem. The left (right) cosets are characterized using gyrolines (cogyrolines) together with automorphisms of the subgyrogroup. With the algebraic structure of the decompositions, we study fiber bundles and sections inherited by the gyroprojectors. Finally, the general theory is exemplified for the aforementioned gyrogroups.

Frames are more stable as compared to bases under the action of a bounded linear operator. Sums of different frames under the action of a bounded linear operator are studied with the help of analysis, synthesis and frame operators. A simple construction of frames from the existing ones under the action of such an operator is presented here. It is shown that a frame can be added to its alternate dual frames, yielding a new frame. It is also shown that the sum of a pair of orthogonal frames is a frame. This provides an easy construction of a frame where the frame bounds can be computed easily. Moreover, for a pair of orthogonal frames, the necessary and sufficient condition is presented for their alternate dual frames to be orthogonal. This allows for an easy construction of a large number of new frames.

Severe malaria is a major public health concern in Angola, particularly among adults, with limited data on clinical outcomes and manifestations. The study therefore assessed the clinical manifestations and outcome of severe Plasmodium falciparum malaria in adult patients admitted to Hospital Central Dr. António Agostinho Neto of Lubango, Angola. The study retrospectively reviewed the individual records of patients over 14 years old, admitted for severe malaria during the first trimester of 2021 and 2022. World Health Organization (WHO) criteria were used to define severity. A total of 640 patients were recorded into the study, 167 in 2021 and 473 in 2022, distributed across the departments; Intensive Care Unit (ICU; n=81), Medicine (MED; n=458) and Infectiology (INF; n=101). The median age was 26 years and 59.4% were males. The most common manifestation of severe malaria was renal impairment (37.4%). The overall mortality rate was 7% and decreased considerably from 10.2% in 2021 to 5.9% in 2022. The increase in malaria cases during 2022 with increased in prevalence of life-threatening signs like renal impairment, jaundice and impaired conscience, underscores the urgent need for enhanced malaria control and surveillance strategies to mitigate morbidity and mortality, highlighting the potential for antimalarial drug resistance.

Introduction Emergency laparotomy is a surgical procedure associated with significantly higher mortality rates compared to elective surgeries. Awake laparotomy under neuraxial anaesthesia has recently emerged as a promising approach in abdominal surgery to improve patient outcomes. This study aims to evaluate the feasibility and potential benefits of using lumbar spinal anaesthesia as the primary anaesthetic technique in emergency laparotomies. Methods We conducted a case series involving 16 patients who underwent emergency laparotomy for bowel ischemia, perforation, or occlusion. Lumbar spinal anaesthesia was employed as the main anaes-thetic technique. We analysed patient demographics, clinical characteristics, intraoperative details, and postoperative outcomes. The primary outcome measures included the adequacy of postoper-ative pain control, the incidence of postoperative complications, and mortality rates. Results Among the 16 patients, adequate postoperative pain control was achieved, with only 2 patients requiring additional analgesia. Postoperative complications, including sepsis, wound dehiscence, and pneumonia, were observed in 7 patients (44%). The observed mortality rate was relatively low at 6% (1 patient). Notably, conversion to general anaesthesia was not necessary in any of the cases, and no early readmissions were reported. Discussion Our findings highlight the feasibility and potential benefits of using neuraxial anaesthesia in emergency laparotomies. The observed low mortality rate and the avoidance of conversion to general anaesthesia suggest that lumbar spinal anaesthesia may be a useful alternative in emer-gency settings. However, the occurrence of postoperative complications in 44% of patients indi-cates the need for cautious patient selection and close monitoring. Further research with larger sample sizes is warranted to fully elucidate the efficacy, safety, and potential impact of this tech-nique on patient outcomes in emergency laparotomies.

In this paper we suggest a first ever construction of fractional integral and differential operators based on signed measures including a vector-valued case. The study focuses on constructing the fractional power of the Riemann-Stieltjes integral with a signed measure, using semigroup theory. The main result is a theorem that provides the exact form of a semigroup for the Riemann-Stieltjes integral with a measure having a countable number of extrema. The article provides examples of semigroups based on integral operators with signed measures and discusses the fractional powers of differential operators with partial derivatives.

Glucose is a simple sugar molecule. The sugar molecule is chemically symbolised as C6H12O6. This means that the glucose molecule contains 6 carbon atoms (C), 12 hydrogen atoms (H) and 6 oxygen atoms (O). In human blood, the molecule glucose circulates as blood sugar. Normally after eating or drinking, our body breaks down the sugars in food and uses them to obtain energy for our cells. To do this, our pancreas produces insulin. Insulin "pulls" sugar from the blood and puts it into the cells for use. If someone has diabetes, their pancreas can't produce enough insulin. As a result, the level of glucose in the blood rises. This can lead one to many potential complications, including blindness, disease, nerve damage, amputation, stroke, heart attack and damage to blood vessels etc. In this study, a non-invasive method for monitoring blood glucose has been developed and is therefore easily usable. The device developed can measure the glucose level continuously and eliminates the disadvantages of the invasive system. Near-IR sensors (optical sensors) were used to estimate the concentration of glucose in the blood; these sensors have a wavelength of 940 nm. The sensor is placed on the tip of the finger and the output of the optical sensor is then connected to the microcontroller at the analogue input. Another sensor used, but only to provide more medical information was the heartbeat sensor. After processing and regression analysis, the glucose level is predicted, and data is sent via the Bluetooth network to a developed APP. The results of the implemented device were compared with available invasive methods. The study consists of a hardware platform inserted into an armband and then a small black parallelepiped-shaped box in which the optical sensors are inserted. The hardware consists of a microcontroller, a Near-IR optical sensor, a heartbeat sensor and a Bluetooth module.

The optimization of photovoltaic (PV) systems is vital for enhancing efficiency and economic viability, especially under Partial Shading Conditions (PSCs). This study focuses on the development and comparison of traditional and advanced algorithms, including Perturb and Observe (P&O), Incremental Conductance (IC), Fuzzy Logic Control (FLC), Grey Wolf Optimization (GWO), Particle Swarm Optimization (PSO), and Artificial Neural Networks (ANN), for efficient Maximum Power Point Tracking (MPPT). Simulations conducted in MATLAB/SIMULINK evaluated these algorithms’ performance under various shading scenarios. The results indicate that while traditional methods like P&O and IC are effective under uniform conditions, advanced techniques, particularly ANN-based MPPT, exhibit superior efficiency and faster convergence under PSCs. The study concludes that integrating AI and ML into MPPT algorithms significantly enhances the reliability and efficiency of PV systems, paving the way for broader adoption of solar energy technologies in diverse environmental conditions. These findings contribute to advancing renewable energy technology and support the green energy transition.

In this paper, the transmutation operator method is used to construct an exact solution to the initial boundary value problem for the equation of multidimensional free transverse vibration of a thin elastic plate with a singular Bessel operator acting on geometric variables. We emphasize that multidimensional Erdélyi–Kober operators of fractional order have the property of a transmutation operator, allowing one to transform more complex multidimensional partial differential equations with singular coefficients acting over all variables into simpler ones. If formulas for solutions are known for a simple equation, then we also obtain representations for solutions to the first complex partial differential equation with singular coefficients. In particular, it is successfully applied to the singular differential equations, especially with Bessel-type operators. Using this operator, the considered problem is reduced to a similar problem without the Bessel operator. Based on the solution to the auxiliary problem, an exact solution to the original problem is constructed and analyzed.

Short-circuit blowing is an important technical means to ensure the rapid surfacing of submersible. In order to study the impact of seven multiple manipulation factors of three levels on blowing, a proportional short-circuit blowing model test bench had been built and L18(37) orthogonal experiments were carried out; then, using Back propagation neural network and Pearson correlation analysis, the experimental data were trained and predicted, correlation between individual factor and blowing was further studied as supplement of orthogonal experiments. It had been proved that both multi-factor combination and individual including blowing duration, sea tank back pressure, the gas blowing pressure of the cylinder group, and sea valve flowing area had larger influence, whose correlation coefficients were 0.6535, 0.8105, 0.5569, 0.5373, of which the F-ratio of blowing duration is over critical value 3.24. And statistical evaluation indicators of Back propagation neural network were between 10e-2 and 10e-13, relative error was less than 3%, and prediction error accuracy was 100%. Based on the results above, a reasonable prediction method for submersible short-circuit blowing had been formed and suggestions on engineering design and operations were proposed, including advantage of short-circuit blowing method, initial condition settings and manipulation strategy.

Fungal infections caused by Candida spp. are responsible for high hospital morbidity and mortality rates. Therefore, there is a continuous search for new antifungal medicines, particularly ones with anti-Candida activity. This review analyzed articles published between 2002 and 2023 considering the anti-Candida activity of chemical compounds identified or isolated in plants of the Anacardiaceae family. In addition, the in-silico prediction of the isolated compounds described was performed. The analysis of 35 studies showed that extracts, essential oils, and compounds from the anti-Candida activity were frequently determined in vitro using the minimum inhibitory concentration (MIC). The most commonly tested species were Candida albicans, C. tropicalis, C. parapsilosis, C. glabrata, C. krusei, and C. guilliermondii, respectively. Essential oils were the most used form (37% of the studies). The isolated compounds with antifungal effects include cardanol, estragole, trans-anethole, β-caryophyllene, myrcene, catechin-3-o-rhamnoside, β-sitosterol-3-O-glucoside, 24Z-isomasticadienolic acid, oleanolic acid, and oleanolic aldehyde. The in-silico evaluation of those isolated compounds revealed the compounds' drug-likeness and possible antifungal activity. However, some of them showed high toxicity. In conclusion, compounds from the Anacardiaceae family show promise for developing new therapeutic antifungal drugs, especially in combination with conventional antifungals.

Over the last two decades, a considerable amount of equipment has been acquired (spreaders, seeders, sprayers, among others) to respond to the challenges of Precision Agriculture (PA) concept. Most of this equipment has been purchased at a high cost. However, many of them, despite still being functional and equipped with sensors, actuators, and electronic processing units capable of adjusting to variations in speed, have become obsolete in terms of communication, and incompatible with new monitoring and control systems based on the “Isobus” protocol. This work aims to present a solution for updating the control system (“Ferticontrol”) of a “Vicon RS-EDW” spreader with variable rate application (VRA), making it compatible with the “InCommand” system from “Ag Leader”. The solution includes low-cost “Arduino” and “Raspberry Pi” microcontrollers and open-source software. The development shows that it is possible to implement a solution that is accessible to farmers in general. It also provides a niche business opportunity for young researchers to set up small technology-based enterprises associated with universities and research centers. These partnerships guarantee permanent innovation and represent a decisive step towards modern, technological, competitive, and sustainable agriculture.

Leonardo da Vinci (1452-1519) is considered one of the greatest geniuses of the Renaissance. His studies developed advanced ideas for his time, even in its most unknown aspects, such as: architecture, urban planning and restoration. He never studied formally, but he learned everything due to his method of observation, the study of other treatises and especially the group of artists with whom he collaborated. After the study of its codices a great interest and knowledge is detected, related to the design, the structural calculation, the materials and the constructive systems, in such a way that their proposals influenced the architecture of the Renaissance, through the work of other authors of your time. The purpose of this article is to make a critical analysis of its excellent architectural proposal in the cupola of the Duomo of Milan and the reasons why it was not carried out under its name. This proposal is included within a discipline in which it has never been recognized as such, but which demonstrated the same qualities as in other fields where it is recognized prestigiously.

This paper analyses the application of deep learning techniques for predicting wave overtopping events in port environments using sea state and weather forecasts as inputs. The study was conducted in the outer port of Punta Langosteira, A Coruña, Spain. A video recording infrastructure was installed to monitor overtopping events from 2015 to 2022, identifying 3709 overtopping events. The data collected was merged with actual and predicted data for the sea state and weather conditions during the overtopping events, creating three datasets. We used these datasets to create several machine learning models to predict whether an overtopping event would occur based on sea state and weather conditions. The final models achieved a high accuracy level during the training and testing stages: 0.81, 0.73, and 0.84 average accuracy during training and 0.67, 0.48, and 0.86 average accuracy during testing, respectively. The results of this study have significant implications for port safety and efficiency, as wave overtopping events can cause disruptions and potential damage. Using deep learning techniques for overtopping prediction can help port managers take preventative measures and optimize operations, ultimately improving safety and helping to minimize the economic impact that overtopping events have on the port's activities.

To assess if SARS-CoV-2 infection induces changes in the urinary volatilomic fingerprint able to be used in the non-invasive COVID-19 diagnosis and management, urine samples of SARS-CoV-2 infected patients (62), recovered COVID-19 patients (30), and non-infected individuals (41) were analysed using solid-phase microextraction technique in headspace mode, combined with gas chromatography hyphenated with mass spectrometry (HS-SPME/GC-MS). In total, 101 volatile organic metabolites (VOMs) from 13 chemical families were identified, being terpenes, phenolic compounds, norisoprenoids, and ketones the most represented groups. Overall, a decrease in the levels of terpenes and phenolic compounds was observed in the control group, whereas norisoprenoids and ketones showed a significant increase. In turn, a remarkable increase was noticed in norisoprenoids and ketones and a milder increase in alcohols, furanic, and sulfur compounds in the recovery group than in the COVID-19 group. Multivariate statistical analysis identified sets of VOMs with the potential to constitute volatile signatures for COVID-19 development and progression. These signatures are composed of D-carvone, 3-methoxy-5-(trifluoromethyl)aniline (MTA), 1,1,6-trimethyl-dihydronaphthalene (TDN), 2-heptanone, and 2,5,5,8a-tetramethyl-1,2,3,5,6,7,8,8-octahydro-1-naphthalenyl ester acetate (TONEA) for COVID-19 infection and nonanoic acid, α-terpinene, β-damascenone, α-isophorone, and trans-furan linalool for patients recovering from the disease. This study provides evidence that changes in the urinary volatilomic profile triggered by SARS-CoV-2 infection constitute a promising and valuable screening and/or diagnostic and management tool for COVID-19 in clinical environment.

Among many other themes, Leonardo da Vinci’s Manuscript B contains several drawings of centrally planned churches, some of which are represented using a plan view paired with a bird’s-eye view. The use of a bird’s-eye instead of an elevation represents an innovative depiction technique, which allows to combine the immediacy of the perspective view with the measurability of the façades, and therefore to describe the three-dimensionality of the buildings. To understand the reasons behind the use of this original technique, the edifices’ shape and classify them we decided to use 3D digital reconstruction techniques, for their ability to avoid misunderstandings in the reconstruction process and in the results. This article describes the method to create the digital models of sixteen churches. A Visual programming language (VPL) script was used as 3D base for modelling the churches achieved from a classification code expressing the aggregative rules of the churches. Then, the geometric process for the construction of the plan and its relationship with the elevation measures was studied for each church. Finally, this information was used for the completion of the 3D models, distinguishing more output variants each time there was an inconsistency between plan and perspective view, a variability of one architectural element or an uncertainty.

A Partial discharge (PD) occurrence in high-voltage (HV) and medium-voltage (MV) power assets is a warning sign of insulation system degradation or defective manufacturing/assembly, that may cause catastrophic damage and eventually lead to the breakdown of the power equipment. Ultra-high frequency (UHF) PD measurement technology has extensively been used to monitor the insulation health of the HV or MV equipment due to its high immunity against ambient noise and conducted disturbances. This paper presents experimental validation of a new design of a UHF planar rectangular microstrip antenna that can be used for PD monitoring of HV and/or MV power equipment, such as power transformers. The designed planar rectangular microstrip antenna has a compact size of 80mmx70mmx1.6mm. Laboratory experiments were performed to validate the antenna sensitivity to PD activity caused by insulation defects created inside an oil-filled transformer tank model. PD measurement results confirm that the proposed rectangular microstrip antenna has high sensitivity and high signal-to-noise ratio (SNR), thanks to its capability to suppress external noise disturbances, especially during online PD monitoring. Thus, the proposed UHF antenna seems to be a promising and alternative PD sensor that can be employed in UHF PD monitoring systems of HV or MV power equipment.

Compressive sensing (CS) is a technique that allows a signal vector to be reconstructed with a number of linear measurements far fewer than its size. In this study, optical hybrid cryptography with simultaneous compressive sensing based on orthogonal matching pursuit (OMP) is proposed as an alternative solution to the two important problems in communications, namely, effective / efficient / signal processing and secure encryption/decrypton. The whole system is able to both compress and encrypt data with attack immunity.

Elephant dung coffee (Black Ivory Coffee) is a special Thai coffee produced from Arabica coffee cherries consumed by Asian elephants and collected from their feces. In this work, elephant dung coffee and controls were analyzed using static headspace gas chromatography hyphenated with mass spectrometry (SHS GC–MS), and chemometric approaches were applied for multivariate analysis and the selection of marker compounds that are characteristic of the coffee. Seventy-eight volatile compounds belonging to 13 chemical classes were tentatively identified, including 6 alcohols, 5 aldehydes, one carboxylic acid, 3 esters, 17 furans, one furanone, 13 ketones, 2 oxazoles, 4 phenolic compounds, 14 pyrazines, one pyridine, 8 pyrroles and 3 sulfur-containing compounds. Moreover, four potential discriminant markers of elephant dung coffee, including 3-methyl-1-butanol, 2-methyl-1-butanol, 2-furfurylfuran and 3-penten-2-one were established. The proposed method may be useful for elephant dung coffee authentication and quality control.

In two previous articles, the extended $(k, t)$--Fibonacci numbers were presented and some of their properties were studied, both in general and particularizing them for the Leonardo numbers. In a second article we study the sum of the extended $(k, t)$--Fibonacci numbers as well as the sums of these odd and even numbers.\\ In this article we study the sum of the squares of these numbers with their properties as well as the generating function, the recurrence relation and the Binet formula.\\ Finally we particularize these results for the generalized $t$--Leonardo numbers.

In this paper, closed forms of the summation formulas for generalized Fibonacci numbers are presented. As special cases, we give summation formulas of Fibonacci, Lucas, Pell, Pell-Lucas, Jacobsthal, Jacobsthal-Lucas numbers.

Background: Intrauterine transfusion (IUT) of the donor and partial exchange (pET) of the recipient is a temporizing treatment for pregnancies with Twin Anemia Polycythemia Sequence (TAPS). We sought to give a detailed description of the procedural approach and outcomes for sequential donor IUT and recipient pET in TAPS. Methods: Retrospective study of spontaneous TAPS referred to the Johns Hopkins Center for Fetal Therapy treated with donor IUT followed by recipient pET utilizing a double-syringe set up. Procedure characteristics and outcomes as well as accuracy of existing transfusion formulas were analyzed and compared with the literature. Results: 5 of 78 patients with spontaneous TAPS underwent a total of 19 combined IUT/pET procedures (median first procedure to delivery interval 5.6 weeks [interquartile range IQR 1.9-6.0]). One pET was stopped for fetal decelerations. Patients delivered at 33.0 weeks [IQR 31.9-33.3] with two survivors and no neonatal transfusion requirements. IUT volumes were 48 ml [IQR 39-63 ml] and pET volumes 32 ml [IQR 20-50] utilizing aliquots of 5 – 20 mls for the latter (p=0.021). For IUTs, assumption of a fetal blood volume below 150 ml/kg underestimated required transfusion volume. For pETs, all formulas required adjustment of dilution volume based on bedside testing (p&lt;0.05 for all). Conclusions: Donor transfusion followed by partial exchange in the recipient can prolong pregnancy in spontaneous TAPS and obviate the need for neonatal transfusion. A double-syringe setup facilitates efficient saline exchange. Because the accuracy of volume formulas is limited, bedside testing is recommended to achieve the target hemoglobin.

Effectively mapping and monitoring rubber plantation is still changing. Previous studies have explored the potential of phenology features for rubber plantation mapping through a pixel-based approach (pixel-based phenology approach). However, in fragmented mountainous Xishuangbanna, it could lead to noises and low accuracy of resultant maps. In this study, we investigated the capability of an integrated approach by combining phenology information with an object-based approach (object-based phenology approach) to map rubber plantations in Xishuangbanna. Moderate Resolution Imaging Spectroradiometer (MODIS) data were firstly used to acquire the temporal profile and phenological features of rubber plantations and natural forests, which delineates the time windows of defoliation and foliation phases. Landsat images were then used to extract a phenology algorithm comparing three different approaches: pixel-based phenology, object-based phenology, and extended object-based phenology to separate rubber plantations and natural forests. The results showed that the two object-based approaches achieved higher accuracy than the pixel-based approach, having overall accuracies of 96.4%, 97.4%, and 95.5%, respectively. This study proved the reliability of a phenology-based rubber mapping in fragmented landscapes with a distinct dry/cool season using Landsat images. This study indicated that the object-based phenology approaches can effectively improve the accuracy of the resultant maps in fragmented landscapes.

In this paper we describe a method which combines sentiment analysis with machine learning techniques and/or multivariate statistical analysis. By applying this methodology it is possible to classify a collection of texts into two or more groups or clusters. On the basis of a number of previously defined clusters, the novelty of the outlined approach is the use of the sentiment analysis results as input to the machine learning model or multivariate statistical analysis. Once the classifier has been obtained, we can assign a given text into one of the pre-established clusters. The groups or clusters can represent different time periods, classes of texts transcribed from different conversations, etc. The method is illustrated through an example taken from one of the two studies in which we have applied this methodology. In one of the studies, the method was used to classify press news of a volcanic eruption, while in the other study it was used to classify the conversations recorded between a chatbot with different kinds of speakers (humans or chatbots). This last study was the seminal work in which we introduced this methodology.

Group A rotaviruses (RVA) have been identified as the leading cause of neonatal calf diarrhea (NCD) In Yunnan, China, despite the limited documentation on this issue within the country. Given the significant impact on animal health and welfare, further attention is warranted to comprehend the prevalence and epidemiology of this disease. In this study, we isolated RVA strains from NCD clinical samples to support RVA epidemic study and further disease control in Yunnan. Material and Methods: Ten fecal samples were obtained from calves with a single episode of neonate calf diarrhea from a farmer during a severe NCD outbreak. For the diagnosis of Group A rotavirus (RVA) infection, fecal reverse transcription-polymerase chain reaction (RT-PCR) was employed as the primary method. Subsequently, RVA isolation was conducted on MA104 cells, with inoculates being pretreated with trypsin TPCK to enhance viral infectivity. The isolated RVA strain was further confirmed through RT-PCR and immunofluorescence assay. Results: RVA virus was isolated from clinical samples following six passages depended on trypsin treatment of inoculates. The sign of CPE detected consisted of increased cell granularity, obscure cell boundaries, cell rounding, and eventual degeneration and detachment of cells. Analysis of sequencing revealed that field isolates was of group A serotype. Phylogenetic analysis based on the ORF sequences of the VP4 and VP7 sequences segments indicated that the isolate was classified as the P[1] genotype. VP4 gene of strain YN-1 shares 75.2%-99.7% nucleotide identity of and 81.6%–99.7% amino acid identity with the complete VP4 sequences of the P[1]. The complete VP7 gene of YN-1 is 981 nucleotide long and encode 326 amino acids. The RotaC v2.0 analysis classified the sequence as the G8 genotype. The VP7 gene of strain YN-1 shares 88.5%-97.7% nucleotide identity and 94.2%-99.1% amino acid identity. Conclusion: This is the first study in China which reports the circulation of Group A NCD on cattle farms in the field. Our study constitutes a crucial and a necessary step allowing preventive and veterinary medicine to support RVA disease controls in Yunnan province, China.

The studied solar pot is a recent invention, which gained a utility model protection in 2021 from the Hungarian Intellectual Property Office under patent number 5489. The device is made for environmentally friendly cooking or heating (by utilizing solar energy) of foods and liquids. Its structure is similar to a double pipe heat exchanger, it has an outer mantle and an inner cooking tank. The goals of the paper are proposing a new physically-based mathematical model describing the solar pot and carrying out computer experiments with it, assembling an experimental system of the pot connected with a solar collector and performing measurements on it. Based on the results, the solar pot can successfully be used for cooking or sterilizing foods or liquids during the studied time period, in Hungary.

Sewage surveillance can be used as an effective complementary tool for detecting pathogens in local communities, providing insights into emerging threats and aiding in the monitoring of outbreaks. In this study using qPCR and whole genomic sewage surveillance, we detected Mpox virus along with other viruses, in municipal and hospital wastewaters in Belo Horizonte, Brazil over a 9 months period (from July 2022 till March 2023). MPXV DNA detection rates varied in our study, with 19.6% (11 out of 56 samples) detected through the hybrid capture method of whole genome sequencing and 20% (12 out of 60 samples) through qPCR. In hospital wastewaters, the detection rate was higher at 40% (12 out of 30 samples), compared to 13.3%(4 out of 30 samples) in municipal wastewaters. This variation could be attributed to the relatively low number of MPXV cases reported in the city, which ranged from 106 to 341 cases during the study period, and to dilution effects, given that each of the two wastewater treatment plants (WWTP) investigated serves approximately 1.1 million inhabitants. Additionally, nine other virus families were identified in both hospitals and municipal wastewaters including Adenoviridade, Astroviridae, Caliciviridae, Picornaviridade, Polyomaviridae, Coronaviridae (which includes SARS-CoV-2), Herspesviridae, Papillomaviridae and Flaviviridae (notably including Dengue). These findings underscore the potential of genomic sewage surveillance as a robust public health tool for monitoring a wide range of viruses circulating in both community and hospitals environments including MPXV.

We introduce two symmetric concepts to physics: “distance” (space and time in one) and “wavematter” (electromagnetic wave packet and matter in one). We claim that physics has chosen the wrong concept of time: It is not aware that the time of a moving object flows in a direction other than my time. We provide 15 proofs for our claim by solving 15 mysteries of physics graphically! For example, we prove that length contraction and time dilation are actually geometrical effects in a 4D manifold that we call “Euclidean spacetime” (ES). We prove that the discrepancy in calculating the Hubble constant stems from a systematic error in the redshift measurement. We prove that what I deem wave, deems itself matter, which solves wave–particle duality. We even untangle quantum entanglement without the issue of non-locality. We finally understand why alternative theories of Euclidean relativity have failed: They are all based on four dimensions of space rather than distance. A huge amount of energy was injected into ES at a point that we take as origin. Ever since has this energy been moving radially away at the speed of light. We live in the 3D hypersurface of an expanding 4D hypersphere. Hyperspherical coordinates have the great advantage that they reduce all that is ever happening to just one formula. So, it is the Theory of Everything in these coordinates: “Energy is covering radial distance which, divided by Euclidean time, is equal to the speed of light.” Acceleration and force like gravitation emerge from a rotation of objects in ES and a subsequent projection to 3D space. Matching the symmetry simplifies physics.

Falls are considered a significant cause of disability, pain, and premature deaths in older adults, often due to sedentary lifestyles and various risk factors. Combining immersive virtual reality (IVR) with physical exercise, or exergames, enhances motivation and personalizes training, effectively preventing falls by improving strength and balance in older people. IVR technology may increase the ecological validity of the assessments. The main goal of our study was to assess the feasibility of using a KAVE-based VR platform combining simulations of Levadas and a Cable Car to perform a balanced assessment and profiling of the older adult population for high risk-of-falls and the related user experience. A VR-based platform using a Wii balance board and a CAVE was developed to assess balance and physical fitness. Validated by the Biodex Balance System (BBS), 25 older adults participated in this study. The usability and presence were measured through the System Usability Scale and ITC-SOPI questionnaires, respectively. The IVR system showed a high presence and a good usability score of 75. Significant effects were found in the maximum excursion of the Centre of Pressure (COP) on the anterior-posterior axis during the Cable Car Simulation (CCS), correlating with BBS metrics. Multiple discriminative analysis models and the support vector machine classified fall risk with moderate to high accuracy, precision, and recall. The system accurately identified all high-risk participants using the Leave-One-Out method. This study suggests that an IVR-based platform based on simulations with high ecological validity can be used to assess physical fitness and identify individuals at a higher risk of falls.