The purpose of this study is to improve the performance of walls under out-of-plane loads, particularly when subjected to the hammering action of the floors. The idea behind the paper is to provide the masonry walls with a device that behaves like a buttress, without having to build a traditional buttress. The solution presented here consists of a mechanical coupling between the three-dimensional net of steel ribbons of the CAM system and the CFRP strips. Since the steel ribbons of the CAM system have a pre-tension, the mechanical coupling allows the steel ribbons to establish a semi-rigid transverse link between the CFRP strips bonded on two opposite sides of a wall. Therefore, two vertical CFRP strips tied by the steel ribbons behave like the flanges of an I-beam and the flexural strength of the ideal I-beam counteracts the out-of-plane displacements of the wall. The experimental results showed that the combined technique inherits the strong points of both constituent techniques: the delamination load is comparable to that of the specimens reinforced with the CFRP strips and the overall behavior is ductile as for the specimens reinforced with the CAM system. They also allowed us to design a more performing combined technique.

The present paper deals with an improvement of the strengthening technique consisting in the combined use of straps—made of stainless steel ribbons—and CFRP strips, to increase the out-of-plane strength of masonry walls. The straps of both the previous and the new combined technique pass from one face to the opposite face of the masonry wall through some holes made along the thickness, giving rise to a three-dimensional net of loop-shaped straps, closed on themselves. The new technique replaces the stainless steel ribbons with steel wire ropes, which form closed loops around the masonry units and the CFRP strips as in the previous technique. A turnbuckle for each steel wire rope allows the closure of the loops and provides the desired pre-tension to the straps. The mechanical coupling—given by the frictional forces—between the straps and the CFRP strips placed on the two faces of the masonry wall gives rise to an I-beam behavior of the facing CFRP strips, which begin to resist the load as if they were the two flanges of the same I-beam. Even the previous combined technique exploits the ideal I-beam mechanism, but the greater stiffness of the steel wire ropes compared to the stiffness of the steel ribbons makes the constraint between the facing CFRP strips stiffer. This gives the reinforced structural element greater stiffness and delamination load. In particular, the experimental results show that the maximum load achievable with the second combined technique is much greater than the maximum load provided by the CFRP strips. Even the ultimate displacement turns out to be increased, allowing us to state that the second combined technique improves both strength and ductility. Since the CFRP strips of the combined technique run along the vertical direction of the wall, the ideal I-beam mechanism is particularly useful to counteract the hammering actions provided by the floors on the perimeter walls, during an earthquake. Lastly, after the building went out of service, the box-type behavior offered by the three-dimensional net of straps prevents the building from collapsing, acting as a device for safeguarding life.

As is well known, the main contribution of the FRP strips to the strength of load-bearing walls is an improvement in the in-plane strength. This paper deals with the possibility of applying the FRP strips in way to modify the strengthening mechanism of the FRP reinforcing system, from an in-plane to an out-of-plane strengthening mechanism. In order to achieve this goal, a second reinforcement system – derived from the CAM system (Active Confinement of Masonry) – provides connections between the FRP strips placed on the opposite sides of the wall. This new strengthening technique – called the straps/strips technique – establishes a stiffness constraint that forces the opposing FRP strips to behave like two flanges of an FRP I-beam embedded in the wall. Consequently, the use of FRP strips also improves the flexural strength of the wall. The present paper briefly summarizes the results obtained in previous works with the straps/strips technique and proposes an improvement of this strengthening technique, based on some weak-points emerged in the early experimentations. The paper also shows the results of a further experimental test, performed with the improved straps/strips technique. Finally, the similarity between FRP strips with transversal connection and concrete wythes of a sandwich panel with flexible connectors leads to interpret the behavior of the ideal I-beam in terms of composite action established between the FRP strips. This paves the way for analytical modeling of the straps/strips technique.

Variable cross-section arch is widely used in practical engineering because of its beautiful arc and excellent mechanical properties. However, there is still no systematic and comprehensive study on the out-plane buckling of variable cross-section arch. In view of this, this paper is concentrated on an elastic analytical research of out-plane buckling of arches with variable cross-section under a uniformly distributed radial local load. The pre-buckling and out-plane buckling behaviour of a variable cross-sectional arch under an external load is quite different from that of an arch with uniform cross-section. The Castigliano's second theorem is used to establish pre-buckling force method equilibrium equations for variable cross-sectional arches under a uniformly distributed radial local load, and corresponding analytical solutions of normal stress, axial compression and the bending moment are obtained. Based on the energy method and the Ritz method, analytical solutions of the critical load for the elastic out-plane buckling of arches with variable cross-section are derived. Comparisons with ANSYS results indicated that the analytical solutions are able to accurately predict the pre-buckling internal forces and critical out-plane buckling load of variable cross-section arches subjected to a uniformly distributed radial local load. It is found that the internal forces and the out-plane buckling load of an arch are significantly affected by the variation of cross-sectional height. With the ratio of cross-sectional height of the top to the end increase, the bending moment decreases and the axial force and critical out-plane buckling load increase. Analytical solutions of pre-buckling internal force and critical out-plane buckling load problems for arches with variable cross-section have a wider significance, since they can provide an effective explicit analytic method for the optimal design of arch structure.

The lay-up of cross laminated timber (CLT) leads to significant differences in properties over its cross-section. Particularly the out-of-plane shear behavior of CLT is effected by the changes in shear moduli over the cross-section. Results from laboratory shear tests are used to evaluate the shear stiffness of 3- and 5-layer CLT panels in their major and minor strength direction. The results are compared to calculated shear stiffness values on evaluated single-layer properties as well as commonly used property ratios using the Timoshenko beam theory and the shear analogy method. Differences between the two calculation approaches are pointed out. The shear stiffness is highly sensitive to the ratio of the shear modulus parallel to the grain to the shear modulus perpendicular to the grain. The stiffness values determined from two test measurements are compared with the calculated results. The level of agreement is dependent on the number of layers in CLT and the property axis of the CLT panels.

Since the introduction of Cross-laminated Timber (CLT) in Austria in the early 1990s, the adoption of this 90°-crosswise-laminated product has seen exponential growth worldwide. Compared to traditional laminated timber products (e.g. glulam), CLT provides improved dimensional stability, but with reduced out-of-plane bending stiffness. To improve the bending stiffness, while maintaining relative dimensional stability, a modified orientation of the inner layers in a diagonal direction can be used. This novel product is Diagonal-Cross-laminated Timber (DCLT), a composite timber product, consisting of inner layers which are rotated at different angle-ply orientations between 0 and 90 degrees to the outer layers. To properly model the out-of-plane bending behavior of the DCLT, analytical models and Finite Element Analysis (FEA) were used and the results were validated by third-point bending tests performed on DCLT panels with angle-ply orientations of 10°, 20°, 40°, 70°, and a conventional CLT 90° panel. The results indicate that DCLT panels with angle-ply cross-layers have a structural advantage in out-of-plane bending over traditional CLT (90°) panels. The development of DCLT and its introduction to the industry could enable the use of lower-quality timber that would not otherwise satisfy structural requirements for CLT.

The internet of things and growing demand for smaller and advanced devices has created the problem of high heat production in the electronic equipment which greatly reduces the work performance and life of the electronic instruments. Thermal interface materials (TIMs) are placed in between heat generating micro-chip and the heat dissipater to conduct all the produced heat to the heat sink. Development of suitable TIMs with excellent thermal conductivity (TC) in both in-plane and through-plane directions is a very important need at present. For efficient thermal management, polymer composites are potential candidates. But in general their thermal conductivity is low compared to that of metals. The filler integration into the polymer matrix is one of the two approaches used to increase the thermal conductivity of polymer composites and is also easy to scale up for industrial production. Another way to achieve this is to change the structure of polymer chains, which fall out of the scope of this work. In this review, considering the first approach, the authors have summarized recent development in many types of fillers with different scenarios by providing multiple cases with successful strategies to improve through-plane thermal conductivity (TPTC) (K⊥). For better understanding of TC the comprehensive background is also presented. In the end, it is given a detailed conclusion which provides drawbacks of some filler, multiple significant routes recommended by other researchers to build Thermally Conductive Polymer Composites, future aspects along with direction so that the researchers can get a guideline to design an effective polymer based Thermal interface materials. A number of methods to improve the effective (out-plane) thermal conductivity of polymer composites are also discussed.

Ultrasound (US) scans of the inferior vena cava (IVC) provide useful information on the volume status of a patient. However, their investigation is user-dependent and prone to measurement errors. An important technical problem is the objective difficulty in studying a very compliant blood vessel like IVC, which makes large respirophasic movements and shows a complicated three dimensional geometry. Using bi-dimensional (2D) B-mode views either in long or short axis has improved the characterization of IVC dynamics compared to a measurement along a single direction (M-mode). However, specific movements of the IVC can challenge also the information provided by these 2D sections. Thus, these two orthogonal views, provided by an US system in X-plane, are here integrated by an innovative method. It is tested on simulated videos of the IVC performing complicated movements, that are compensated by the new method, overcoming the biased measurements provided by 2D scans. The method is then applied on example experimental data.

The use of educational robotics has become increasingly popular in STEM education, offering motivating and hands-on learning experiences. This paper explores the potential of educational robotics for teaching plane curves at the university level. Specifically, it investigates the development and implementation of a LEGO SPIKE Prime robot designed to draw various central trochoids, including epicycloids and hypocycloids. The robot’s construction and programming are described, emphasizing the relationship between the robot’s physical movements and the mathematical equations of the curves it produces. The study also examines the integration of dynamic geometry software, which allows for visualization of the curves and verification of the robot’s accuracy. The paper concludes that educational robotics can serve as a valuable tool for enhancing both theoretical and practical understanding of mathematical and engineering concepts, offering a more engaging and interactive approach to learning.

Any quantization maps linearly functions on a phase space to symmetric operators in a Hilbert space. Covariant integral quantization combines operator-valued measure with symmetry group of the phase space. Covariant means that the quantization map intertwines classical (geometric operation) and quantum (unitary transformations) symmetries. Integral means that we use all ressources of integral calculus, in order to implement the method when we apply it to singular functions, or distributions, for which the integral calculus is an essential ingredient. In this paper we emphasize the deep connection between Fourier transform and covariant integral quantization when the Weyl-Heisenberg and affine groups are involved. We show with our generalisations of the Wigner-Weyl transform that many properties of the Weyl integral quantization, commonly viewed as optimal, are actually shared by a large family of integral quantizations.

The paper presents the prediction of hydrodynamic characteristics of different rudder -plane configurations behind a submarine in deep water through the Reynolds-Averaged Navier-Stokes method in Ansys Fluent Solver. The hydrodynamic force and moment acting on the Cross-plane, X-plane, and Y-plane rudder configurations are analyzed for estimating hydrodynamic coefficientsfor predicting the advantages of each configuration to control the ship. The obtained results show that X-force of the X-plane rudder configuration is larger than the force acting on the Cross-plane rudder and Y-plane rudder configurations. However, Y-force, and Z-force of the X-plane rudder configuration are significantly greater than the Y-force of the left configurations. The same tendency can be seen in the moment of the X-plane rudder about the y-axis and z-axis. The roll moment induced by the Y-plane and Cross-plane rudder configurations is significantly larger than the case of the X-plane rudder configuration.

Sea cucumber peptides are small molecular peptides with biological function obtained from fresh sea cucumber as feedstock, which were hydrolyzed by protease, separated ,and purified. As the main product of sea cucumber refinement, it more accurately expresses the nutritional effect of sea cucumber and has a wide range of potential applications. It has been demonstrated that sea cucumber has a certain value-added effect on bone mineral density regulation, but the differences in bone mineral density regulation of extracts from different parts of sea cucumber and the techniques contributing to the efficient isolation of bone sea cucumber peptides have not been reported. Firstly, the aim of this study was to reveal the differences in osteogenic activities of enzymatic peptides from three major parts of sea cucumber: the body wall, the egg protein, and the intestinal protein. Then, the bone-enhancing sea cucumber peptides were isolated based on the characteristics of the dif-ferences in molecular weight distribution, hydrophilicity, and ionisation degree of sea cucumber, and to explore the possible mechanisms of their action. The findings indicated that sea cucumber peptides extracted from three distinct sites exhibited a dose-dependent enhancement of osteoblast proliferation and differentiation. Upon evaluating the three methods of sea cucumber peptide separation based on molecular weight distribution, hydrophilicity, and ionization, it was observed that the fraction isolated by hydrophobicity and

In a saline semi-isolated Lagoon on the Cape Zeleny (White Sea), the annual dynamics of the vertical hydrological structure, and the seasonal dynamics of phytoplankton were traced, including species composition, and vertical distribution, abundance, nutrition type,and biomass.293 species and supraspecific taxa of algae and cyanobacteria were found. Most of the identified species are marine, and 38 species are freshwater. Taxonomic composition changed in the Lagoon during the year. Dinoflagellates dominated in winter and early June; unidentified cocci and flagellates in July; diatoms, dinoflagellates and unidentified cells in August; dinoflagellates in September; and unidentified cocci and flagellates in October–November. The abundance of algae also changed in the Lagoon during the year. The integrated biomass in the water column varied from 0.01 g C/m2 in January to 0.78 g C/m2 in early September. According to the abiotic parameters, the water column of the Lagoon is subdivided into several zones with different conditions and corresponding phytoplankton communities. Similarity between the communities of different horizons was 32-46% in summer and 7% in winter. The chemocline layer was the most populous. Almost the entire year it contained a maximum of phytoplankton biomass, 1-2 orders of magnitude higher than that in the overlying horizons. Comparison phytoplankton in the lagoon and in the nearby sea area was carried out. Despite the connection between the Lagoon and the sea phytoplankton structure in the surface water layer in the Lagoon and in the sea differs significantly in composition, quantitative parameters, and seasonal dynamics. The similarity of the communities in the sea and the Lagoon never exceeded 50%. In terms of biomass, the Lagoon lags behind the sea until mid-summer, but, starting from August, it outnumbers it, and the phytoplankton development in the Lagoon lasts longer, until late autumn. The phytoplankton structure and dynamics in the Lagoon and the sea by 24.5% was related to the daylight, water salinity, oxygen content and pH, but did not depend on water T, underwater illuminance, and depth. Oxygen content and pH are defined by PhP activity. Salinity serves as a vector of the vertical sequence of ecological niches. The daylight length seems to be the crucial factor of the seasonal PhP dynamics in the semi-isolated coastal stratified lakes and lagoons.

7046 aluminum alloy has good fatigue property, corrosion resistance and weld property, but the moderate strength and plasticity limit its wider application and development. In the present study, severe plastic deformation (SPD) was applied prior to T6 treatment to significantly strengthen and toughen the 7046 aluminum alloy. Results indicate that the alloy processed by 4 passes of equal channel angular pressing (ECAP) at 300 ℃ prior to T6 treatment exhibits an excellent mechanical performance, with ultimate tensile strength (UTS) and elongation (EL) of 485 MPa and 19%, exhibiting an improvement of 18.6% and 375% compared to that of the T6 alloy, respectively. The mechanical properties of the alloy are further improved by the additional room temperature (RT) rolling process, with UTS of 508 MPa and EL of 23.4%. There are more precipitates of η' and Al6Mn phases in the 300℃4P-R80%-T6 and 300°C4P-T6 alloys, which contribute to the strengthening and toughening enhancement by SPD processed T6 alloy. The results of this work may shed some light on enhancing 7046 aluminum alloy.

A century-old scientific conundrum is solved in this paper. The Prandtl mixing length modelled plane boundary turbulent flow is described by: $\frac{du^+}{d{y^+} }+\kappa^2{y^+} ^2\left( \frac{du^+}{d{y^+} }\right)^2=1$, together with boundary condition $ {y^+} =0:\, u^+=0$. Only an approximate solution to this nonlinear ordinary differential equation (ODE) has been sought so far, however, the exact solution to this ODE has not been obtained. By introducing a transformation, $2\kappa y^+=\sinh \xi$, I successfully find the exact solution of the ODE as follows: $u^+=\frac{1}{\kappa}\ln(2\kappa {y^+} +\sqrt{1+4\kappa^2{y^+} ^2})-\frac{2{y^+} }{1+\sqrt{1+4\kappa^2{y^+} ^2}}$.

Recent research has drawn attention to the ambiguity surrounding the definition and learnability of Out Of Distribution (OOD) recognition. The term "Out of Model Scope" (OMS) detection provides a clearer perspective, although the original problem remains unsolved. The ability to detect OMS inputs is particularly beneficial in safety-critical applications such as autonomous driving or medicine. By detecting OMS situations, we not only enhance the system's robustness but also prevent it from operating in unknown and unsafe scenarios. In this paper, we introduce a novel approach for OMS detection that combines three sources of information: 1) the original input, 2) the latent feature space extracted by an encoder, and 3) the synthetic data generated from the encoder's latent feature space. We demonstrate the effectiveness of combining original images and synthetically generated images against adversary attacks in the computer vision domain. We achieve results comparable to other state-of-the-art methods and demonstrate that any Encoder can be integrated into our pipeline in a plug-and-train fashion. Our experiments further evaluate which combination of the Encoder's features works best in order to discover OMS samples and highlight the importance of a compact feature space for the training of the Generator.

People have always hoped to be able to fill an entire plane with ``single unit cells'' without periodicity. This wish was realized after the mathematician discovered a 13-sided ``single unit cell'' named `einstein'. These non-periodic tessellations generally exhibit anisotropic properties, making them superior in terms of mechanical performance compared to periodic structures. From the perspective of information entropy, the reason behind the improved mechanical properties of these structures is the higher entropy associated with non-periodic configurations. To quantify the disorder of non-periodic structures, we propose an entropy expression for the `einstein' metamaterial. To demonstrate the mechanical properties of these high-entropy structures, we fabricate specimens using 3D printing and conducte mechanical experiments. For comparative analysis, we also use ABAQUS to perform finite element analysis of the problem. The research results reveal that the mechanical properties of high-entropy structures created by the non-periodic stacking of cells are significantly improved compared to those of low-entropy structures created by periodic stacking. The conclusions drawn from the study of individual issues are generalizable and may be of assistance in future material and structural design.

There are given algebraic and integral identities for a pair or a triple of plane solenoidal fields. As applications, we obtain sufficient potentiality conditions for a plane vector field. The integral identities are also important for exact a priori estimates.

Deep learning has increasingly been employed to identify minerals. However, deep learning can only be used to identify minerals in the distribution of the training set, while any mineral outside the spectrum of the training set is inevitably categorized erroneously within a predetermined class from the training set. To solve this problem, the study introduces the approach that amalgamates One-Class Support Vector Machines (OCSVM) with the ResNet architecture for the out-of-distribution mineral detection. Initially, ResNet undergoes training using a training set comprising well-defined minerals. Subsequently, the earlier layers of the trained ResNet are employed to extract the discriminative features of the mineral under consideration. These extracted mineral features then become the input for OCSVM. When OCSVM discerns the mineral in the training set's distribution, it triggers the subsequent layers within the trained ResNet, facilitating the accurate classification of the mineral into one of the predefined categories encompassing the known minerals. In the event OCSVM identifies the mineral out of the training set's distribution, it is unequivocally categorized as an unclassified or 'unknown' mineral. Empirical results substantiate the method's capability to identify out-of-distribution minerals while concurrently maintaining a commendably high accuracy rate for the classification of the 36 in-distribution minerals.

According to the standard cold dark matter (CDM) cosmology, the structure of dark halos including those of galaxy clusters reflects their mass accretion history. Older clusters tend to be more concentrated than younger clusters. Their structure, represented by the characteristic radius $r_s$ and mass $M_s$ of the Navarro-Frenk-White (NFW) density profile, is related to their formation time. In this study, we show that $r_s$, $M_s$, and the X-ray temperature of the intracluster medium (ICM), $T_X$, form a thin plane in the space of $(\log r_s, \log M_s, \log T_X)$. This tight correlation indicates that the ICM temperature is also determined by the formation time of individual clusters. Numerical simulations show that clusters move along the fundamental plane as they evolve. The plane and the cluster evolution within the plane can be explained by a similarity solution of structure formation of the universe. The angle of the plane shows that clusters have not achieved “virial equilibrium” in the sense that mass/size growth and pressure at the boundaries cannot be ignored. The distribution of clusters on the plane is related to the intrinsic scatter in the halo concentration--mass relation, which is originated from the variety of cluster ages. The well-known mass--temperature relation of clusters ($M_\Delta\propto T_X^{3/2}$) can be explained by the fundamental plane and the mass dependence of the halo concentration without the assumption of virial equilibrium. The fundamental plane can also be used for calibration of cluster masses.

This study aimed to investigate the fatigue performance and interfacial strengthening mechanisms of Al6061-to-Cu dissimilar lap joints via electromagnetic pulse welding (EMPW). The load-bearing capacity of the joints at discharge voltages of 14 kV and 16 kV was superior to that of 12 kV. Furthermore, the fatigue life of the 14 kV joints was one order of magnitude higher compared to the 12 kV joints. SEM observation of the fatigue fracture surface revealed the presence of typical "tire-mark" fatigue striations only in the 14 kV joint, indicating higher ductility and the ability to withstand extended plastic deformation. Notably, ultra-fine nanocrystalline Al2Cu phase, amorphous phase, and numerous dislocations hindered EBSD acquisition in the transition zone. Nevertheless, dense low-angle grain boundaries (LAGBs) and refined grains were examined at the bonding interface. This suggests that the high-velocity collision caused severe plastic deformation and led to the formation of substructures. The interfacial strength was attributed not only to the "wave-like" or "inverted hook-like" diffusion layer but also to the presence of refined grains along the interface and nanocrystalline Al2Cu in the transition zone. Furthermore, the hybrid nanocrystalline-amorphous microstructure strengthened the joint by regulating the balance between strength and ductility.

Systemic inflammation and coronary microvascular endothelial dysfunction are essential pathophysiological factors in heart failure with preserved ejection fraction (HFpEF) that support the use of statins. The pleiotropic properties of statins, such as anti-inflammatory, antihypertrophic, antifibrotic, and antioxidant effects, are generally accepted and may be beneficial in HF, especially in HFpEF. Numerous observational clinical trials have consistently shown a beneficial prognostic effect of statins in patients with HFpEF, while the results of two larger trials in patients with HFrEF have been controversial. Such differences may be related to a more pronounced impact of the pleiotropic properties of statins on the pathophysiology of HFpEF and pro-inflammatory comorbidities (arterial hypertension, diabetes mellitus, obesity, chronic kidney disease) that are more common in HFpEF. This review discusses the potential mechanisms of statin action that may be beneficial for patients with HFpEF, as well as clinical trials that have evaluated the statin effects on left ventricular diastolic function and clinical outcomes in patients with HFpEF.

Organised hiking and trekking tours are promoted by many providers in adventure travel. Such guided tours shall be engaging for the tourists and evoke positive attitudes towards enjoying nature. We present the Trekking Engagement Profile as a tool to evaluate engagement factors of such guided tours, based on engagement research performed in a different domain, namely evaluating engagement in museums and science centres. This tool shall strengthen guides’ soft skills and enable them to increase engagement during an ongoing arrangement. For instance, the Trekking Engagement Profile can be applied when tourists indicate that the quality of a guided tour is not entirely to their liking. We show the viability of using the Trekking Engagement Profile in a small study with guides and participants of trekking tours offered by the Norwegian Trekking Association. Further, we offer guidance and charts to promote its practical use.

In this study, we provide the Lie symmetries and a classification of plane symmetric static space-times. Based on the invariance of the Lagrange equations of plane symmetries static space-time systems under the transformation Lie group, we provide the Lie symmetry determination equation, Lie symmetry theorem, and the conserved quantity of the systems; by utilizing the Lie symmetry method to solute the system, we give complete classification of the plane symmetric static space-times systems. The research results indicate that using the Lie symmetry method to study plane symmetric static spacetime can identify a series of conserved quantities that exist in the system; Discovered 5 basic Lie symmetries in the system; When the metric parameters of the system are appropriately selected, the plane symmetric static spacetime can have 6, 7, 8, 9, 11, and 17 Lie symmetric symmetries and conserved quantities.

The Norwegian Museum of Science and Technology have developed a learning concept for school classes in science centres named ‘learning trails’. In this concept, groups of students perform a series of thematically related experiments with installations in the science centre. The learning trails are designed to support the generic learning outcomes for science centre visits. We argue for using the previously developed Engagement Profile in an indicator to determine both media forms and generic learning outcomes for such learning concepts. Further, we implemented the learning trails in two modes: one mode used paper-based content to guide the students, while the other mode supported the use of tablet PCs where engaging content is triggered when the students approach the location of an experiment in the learning trail. We studied the engagement factors of the learning trails and observed how school classes use these. In a study with 113 students from lower secondary school, they answered short questionnaires that were integrated into the implementation of the learning trails. While the concept of the learning trails was evaluated positively, we could not find significant differences in how engaging the two implemented modes were.

: Optical coherence tomography is a non-invasive imaging technique that provides three-dimensional visualization of subsurface tissue structures. OCT has been proposed and explored in literature as a tool to assess oral cancer status, select biopsy sites, or identify surgical margins. Our endoscopic OCT device can generate widefield (centimeters long) imaging of lesions at any location in the oral cavity – but it is challenging for raters to quantitatively assess and score large volumes of data. Leveraging a previously developed epithelial segmentation network, this work develops quantifiable biomarkers that provide direct measurements of tissue properties in three-dimensions. We hypothesize that features related to morphology, tissue attenuation, and contrast between tissue layers will be able to provide a quantitative assessment of disease status (dysplasia through carcinoma). This work retrospectively assesses seven biomarkers on a lesion-contralateral matched OCT dataset of lateral and ventral tongue (40 patients, 70 sites). Epithelial depth and loss of epithelial-stromal boundary visualization provide the strongest discrimination between disease states. The stroma optical attenuation coefficient provides distinction of benign lesions from dysplasia and carcinoma. The stratification biomarkers visualize subsurface changes which provides potential for future utility in biopsy site selection or treatment margin delineation.

We propose a method for creating parallel Bessel-like vortical optical needles with an arbitrary axial intensity distribution via superposition of different cone-angle Bessel vortices. We analyze the interplay between the separation of individual optical vortical needles and their respective lengths and introduce a super-Gaussian function as their axial profile. We also analyze the physical limitations to observe well-separated optic needles, as they are influenced by mutual interference of the individual beams. To verify our theoretical and numerical results, we generate controllable spatial arrays of individual Bessel beams with various numbers and spatial separations by altering the spectrum of the incoming laser beam via the spatial light modulator. We demonstrate experimentally how to implement such beams using a diffractive mask. The presented method facilitates the creation of diverse spatial intensity distributions in three dimensions, potentially finding applications in specific microfabrication tasks or other contexts. These beams may have benefits in laser material processing applications such as nanochannel machining, glass via production, modification of glass refractive indices, and glass dicing.

There are currently no effective screening measures to detect early or occult tubo-ovarian cancers resulting in late-stage detection and high mortality. This work explores whether an optical imaging catheter can detect early-stage tubo-ovarian cancers or precursor lesions where they originate in the fallopian tubes. This device collects co-registered optical coherence tomography (OCT) and autofluorescence imaging (AFI). OCT provides three-dimensional assessment of underlying tissue structures; autofluorescence imaging provides functional contrast of endogenous fluorophores. Ex vivo fallopian tubes (n=28; n=7 cancer) are imaged; we present methods for the calculation of and analyze eleven imaging biomarkers related to fluorescence, optical attenuation, and OCT texture for their potential to detect tubo-ovarian cancers and other lesions of interest. We visualize folded plicae, vessel-like structures, tissue layering, hemosiderin deposits, and regions of fibrotic change. High grade serous ovarian carcinoma appears as reduced autofluorescence paired with homogenous OCT and reduced mean optical attenuation. Specimens containing a cancerous lesion demonstrate significant increase in median autofluorescence intensity and decrease in entropy compared specimens with no lesion. Non-cancerous specimens demonstrate an increase in optical attenuation in the fimbriae when compared to the isthmus or ampulla. We conclude that this approach shows promise and merits further investigation of diagnostic potential.

This paper studies the duration patterns of unemployment spells for immigrants and the determinants of unemployment’s completion into one of a number of studied labour market states in Finland. We estimate a duration model for unemployment with competing risks of its terminating into employment, labour market training or economic inactivity. Taking into account the wide period of observation and opportunities to analyse processes of labour market integration during various periods of economic development in Finland, in combination with the individualistic character of the labour careers of immigrants, this research is beneficial owing to the many various findings concerning labour market integration of immigrants. The approach undertaken in this research has a dualistic “descriptive-dynamic” character under which integration is understood as a never-ending process, which is conditioned by a time period of long-term existence and a context of solitary action. We find that transitions out of unemployment spells have a cyclical character; after every new “cycle” in unemployment, the probability of terminating unemployment decreases further. We also find that ascriptive factors make sense in the process of job-placement of immigrants from unemployment. Therefore, the gender, education and age of immigrants, as well as the effect of the period in which first unemployment occurred, potentially predict transitions out of unemployment and further labour market integration of immigrants.

Renovation, restoration, remodeling, refurbishment, and retrofitting of build-ings often imply modifying the behavior of the structural system. Modification sometimes includes applying forces (i.e., concentrated loads) to beams that before were subjected to distributed loads only. For a reinforced concrete structure, the new condition causes a beam to bear a concentrated load with the crack pattern that was produced by the distributed loads that acted in the past. If the concentrated load is applied at or near the beam’s midspan, the new shear demand reaches the maximum around the midspan. But around the midspan, the cracks are vertical or quasi-vertical, and no inclined bar is present. So, the actual shear capacity around the midspan not only is low, but also can be substantially lower than the new demand. In order to bring the beam capacity up to the demand, fiber-reinforced-polymer composites can be used. This paper presents a design method to increase the concentrated load-carrying capacity of reinforced concrete beams whose load distribution has to be changed from distributed to concentrated, and an analytical model to pre-dict the concentrated load-carrying capacity of a beam in the strengthened state.

Approximately 85 million people's houses are scattered all over Indonesia, and almost all are in strong earthquake areas. In every earthquake, the houses are generally damaged or collapsed. Therefore, those houses must be strengthened to make them earthquake resistant. This paper discusses a gradual strengthening of existing houses using ferrocement bandaging. The gradual strengthening is introduced due to limited funding of the people. It also serves as an educational tool to educate people to be self-sufficient in building their earthquake-resistant houses. The first step, maybe the sleeping room shall be strengthened so that if there is an earthquake during night-time, people will be safe, and if there is an earthquake during the daytime, people can immediately run to that particular room. A global analysis is made of a sample house shaken by Palu, Central Sulawesi earthquake 2018, and West Sumatra earthquake 2009, with one room strengthened to show that the strengthened room can survive the earthquakes. Then the analysis is continued gradually to the other rooms until the masonry house is fully strengthened by ferrocement bandaging. The results show that the masonry house strengthened by ferrocement layers is earthquake resistant.

Polymer-based composites are widely used in the automotive, security, aeronautical and space industries, to mention a few. This is because of their good mechanical properties, which are similar to those of metals but with the attraction of being lightweight. Kevlar® as a reinforcement is extensively used in the security industry owing to its good ballistic properties. This investigation presents the mechanical characterization based on in-plane quasi-static tensile testing of Kevlar® composite using a universal testing system. The methodology developed for the preparation of coupons is based on pressure, temperature and time. As a result of this work, elastic moduli (EL and ET), Poisson’s ratio (νLT), shear modulus (GLT) and strengths (XT, YT, S) were obtained. It is worth mentioning that there is scarce or no characterization of this material in the literature, and those studies that do characterize it do not present the coupon thermoforming conditions or the reasons of the specimen dimensions (width, length and thickness).

We report herein high-resolution x-ray diffraction measurements of basal plane bending of homoepitaxial single-crystal diamond (SCD). The results reveal that growth parameters such as temperature, growth time and basal plane bending of the substrate affect the basal plane bending of SCD. First, the basal plane bending of SCD depends mainly on the substrate itself. The basal plane bending of SCD becomes more severe with increasing basal plane bending of the substrate and this type of basal plane bending cannot be recovered. The SCD growth experiments show that the basal plane bending increases at high temperature and with increasing growth time. Finally, to understand the mechanism behind basal plane bending, we investigate the substrate-surface temperature distribution as a function of basal plane bending of SCD fabricated by chemical vapour deposition (CVD). This allows us to propose a bending model and understand the origin of basal plane bending. The results indicate that an uneven temperature distribution on the substrate surface is the main cause of the CVD diamond base-plane bending.

A focal plane array (FPA) detector was used for hyperspectral imaging in the infrared (IR) spectral region using thermal and synchrotron light sources. FPA Fourier-transform IR (FTIR) imaging microspectroscopy will be able to monitor real time changes at specific absorption bands when combined with high brightness synchrotron source. In this study, several types of samples with unique structural motifs were selected and used for assessing the capability of the FPA-FTIR imaging technique. It was shown that the time required for polariscopy at IR wavelengths can be substantially reduced by the FPA-FTIR imaging approach. By using natural and laser fabricated polymers with sub-wavelength features, alignment of absorbing molecular dipoles was revealed as well as higher order patterns (laser fabricated structures). Micro-spectroscopy of absorber orientation reveals alignment patterns even when they are not spatially resolved.

New multilayer 3D nanocomposite wear-resistant ion-plasma hard and superhard coatings Avinit [(TiN-AlN)(Mo-Cr-V-Si)]_n have been developed.The introduction of additional alloying elements (Mo, Cr, V, Si) into the Ti-Al-N coating composition, which have a high affinity for nitrogen and are capable of forming strong nitride nanoparticles in the Ti-N and Al-N layers.This makes it possible to obtain hard and superhard hardening coatings.The metallographic and tribological studies carried out indicate the prospects of the developed multicomponent multilayer nano- and microstructured Avinit coatings for increasing wear resistance and reducing friction coefficients.This paper is devoted to the development and implementation of Avinit vacuum plasma technologies for strengthening cutting and forming tools to improve tool performance.Production tests of cutting tools with Avinit's developed multilayer wear-resistant ion-plasma coatings in production conditions at many large machine-building enterprises have shown their high efficiency.In serial production, the wear resistance of tools increases by 3 to 30 times, stamps by 5 to 100 times, and parts rubbing against abrasive materials by 10 to 100 times.Avinit's vacuum plasma technologies have been successfully implemented in production in the aggregate and engine building, transport engineering, and power engineering industries.Positive experience in applying multicomponent coatings has been gained not only when applying hardening coatings to manufactured cutting tools, but also after regrinding to regrindable carbide cutting tools from domestic and foreign manufacturers.

Steel fibre reinforced concrete (SFRC) consists of short hooked steel fibres randomly distributed and oriented within the cementitious matrix. The contribution of fibre in bridging cracks to provide the stress transfer required relies upon the orientation of the fibre in the concrete. Bridging fibre aligned with a crack are less effective than those inclined to it. Therefore, understanding the pull-out behaviour of misaligned fibre is a key factor to quantify and optimize the design of SFRC in the structural applications. In the laboratory a single oriented fibre embedded in a solid cylinder of concrete is subjected to a pull-out test where the axis of a tensile force is aligned with the axis of the cylinder. Based upon the observed behaviour this paper presents a new analytical bounding approach to capture the pull-out response of misaligned hooked-end steel fibre embedded in a concrete matrix. The analysis is based upon a transversely isotropic condition assumed for the plasticity that occurs in the cold drawn fibre. The model accounts for the influence of fibre diameter and the combined strengths of the steel and concrete. The model predictions have also been compared with other experimental results published in the literature. The results showed that the model can predict pull-out loads reasonably for different fibre orientations between bounds of failure derived from the strengths of the two constituents. A critical orientation is observed at maximum strength. Therein, an understanding of the pull-out behaviour of misaligned, hooked-end fibres is necessary to optimize the strength of concrete from this method of reinforcement.

We describe a novel machine that uses the greater-than-100% efficiency of air/ground-source heat pumps to recursively generate electricity via steam-powered generators, taking thermal energy from the ambient environment to convert into electrical power. The invention of a machines that generate clean power at low costs will be fundamental to the future of electricity. We estimate efficiency and calculate minimum efficiencies for unknown parts to consider the applicability of this machine to the real world.

This paper explores the emergence of Sustainability-Linked Bonds (SLBs) as an innovative instrument to finance sustainability objectives. SLBs have emerged as a transformative financial instrument, establishing an explicit link between cost of funding and sustainability objectives. SLBs were first launched in 2019 and represent 7% of labelled bonds, still dominated by the more established green bonds. Issuance of SLBs now exceeds $250 billion. Following initial enthusiasm, they are now facing criticism. In the context of the growth of sustainable finance and concerns of greenwashing, this paper investigates ways to enhance the design of SLBs. Drawing on literature and expert interviews, the findings highlight the strong potential of SLBs to contribute to sustainability financing, especially in hard-to-abate sectors. The paper identifies the key positive attributes of SLBs and their limitations in five areas: key performance indicators’ (KPI) selection, sustainability performance targets’ (SPT) calibration, bond characteristics, reporting practices, and resource requirements. Recommendations to financial intermediaries, issuers and policy makers include defining standardized KPIs based on a materiality assessment, requesting SPTs to be supported by science and in line with an issuer’s core strategy, tailored step-up mechanisms and avoidance of call loopholes, and stricter reporting. SLBs represent an opportunity to add rigor to sustainable finance and better price externalities, where material topics have an explicit impact on cost of funding and credit ratings.

It is well established that the reaction cycles involving some halogenated alkanes (so-called ozone-depleting substances, ODS) contribute to the depletion of ozone in the stratosphere, thus causing the Montreal Protocol (initially signed in 1987) and later amendments. The Protocol called for the scheduled phase-out of ODS, including chlorofluorocarbons (CFC), hydrochloro-fluorocarbons (HCFC), carbon tetrachloride (CCl4), halon, methyl chloroform (CH3CCl3), me-thyl chloride (CH3Cl), and even hydrofluorocarbons (HFCs). In view of the urgent importance of ozone layer protection to the globally ecological environment, the Taiwan government took regulatory actions on reducing ODS consumption since 1993 by the joint-venture of the central competent authorities. Under the regulatory requirements and the industry’s efforts by adopt-ing the alternatives to ODS and abatement technologies, the phase-out of some ODS (i.e., CFC, CCl4, halon, and CH3CCl3) have been achieved prior to 2010. The consumptions of HCFCs and methyl chloride have been significantly declined over the past three decades (1993-2022). However, HFC emission indicated a V-type variation during the period. Due to the local pro-duction and extensive use of HFC in Taiwan, its emissions increased from 663 kilotons of carbon dioxide equivalents (CO2eq) in 1993 to 2,330 kilotons of CO2eq in 2001, and then decreased to 373 kilotons of CO2eq in 2011. Since then, the emissions of HFC largely used as the alternatives to ODS showed an upward trend, increasing to 1,555 kilotons of CO2eq in 2022. To be in compliance with the Kigali Amendment (KA-2015) to the Montreal Protocol for mitigating global warming, the Taiwan government has taken regulatory actions in reducing the consumption of some HFC substances with high global warming potential (GWP) under the authorization of the Climate Change Response Act in 2023, aiming at the baseline consumption in 2024 by 80 % reduction by 2045.

Purpose: To simplify the application of optical coherence tomography (OCT) for examination of subsurface morphology in the oral cavity and reduce barriers towards adoption of OCT as a biopsy guidance device. The aim of this work was to develop automated software tools for simplified analysis of the large volume of data collected during OCT. Methods: Imaging and corresponding histopathology were acquired in-clinic using a wide-field endoscopic OCT system. An annotated dataset (n = 294 images) from 60 patients (34 male, 26 female) was assembled to train four unique neural networks. A deep learning pipeline was built using convolutional and modified u-net models to detect the imaging field of view (network 1), detect artifacts (network 2), identify the tissue surface (network 3), and identify the presence and location of the basement membrane (network 4). Results: The area under the curve of the image and artifact detection networks was 1.00 and 0.94 respectively. The Dice similarity score for the surface and basement membrane segmentation networks was 0.98 and 0.83 respectively. Conclusion: Deep Learning (DL) techniques can identify the location and variations in the epithelial surface and basement membrane in OCT images of the oral mucosa. Segmentation results can be synthesized into accessible en face maps to allow easier visualization of changes.

A temperature-modulated pyroelectricity measurement system for a small single crystal is developed and applied to standard sample measurements performed on a thin single crystal of lithium niobate. The modulation measurement is based on the AC technique, in which the temperature of the sample is periodically oscillated, and the synchronized pyroelectric signal is extracted using a lock-in amplifier. Temperature modulation is applied by irradiating periodic light on the sample placed in the heat exchange gas. To apply this technique to the transparent reference sample, a commercially available black resin is coated on the sample’s surface to absorb the light energy and transmits it to the specimen. The experimental results are analyzed using a two-layer heat transfer model to verify the effect of the light-absorbing layer as well as the non-contact temperature modulation system.

Drought is among the most important abiotic stressors influencing food-crop production worldwide. Currently, drought-tolerant maize materials are rarely used for actual breeding because corn production primarily focuses on heterosis to generate desired varieties. In this article, we reviewed current work on assessing maize drought tolerance. We suggested that the development of enhanced screening techniques must clearly consider the connection between theory and application. We strongly recommend that agricultural scientists focus on translating the results of laboratory experiments into practical methods for improving crop productivity.

Background: Whole-body computed tomography (WBCT) is commonly employed for primary screening in pediatric patients experiencing out-of-hospital cardiac arrest (OHCA) without prehospital return of spontaneous circulation (ROSC). This study aimed to evaluate the cause of OHCA on WBCT and compare WBCT findings between ROSC and non-ROSC groups in non-traumatic pediatric OHCA cases in an emergency department (ED) setting. Methods: A retrospective analysis was conducted on 27 pediatric patients (mean age: 32.4 months; median age: 10 months) who experienced non-traumatic OHCA without prehospital ROSC and were transported to our tertiary care hospital between January 2013 and December 2023. WBCT scans were performed to investigate the cause of OHCA, with recorded findings in the head, chest, abdomen, and subcutaneous tissues. Results: In all cases, the direct causes of OHCA were undetermined, and WBCT identified no fatal findings. Statistical comparisons of CT findings between the ROSC and non-ROSC groups revealed significant differences. The non-ROSC group had a higher incidence of brain swelling, loss of cerebral gray-white matter differentiation, symmetrical lung consolidation/ground-glass opacity, cardiomegaly, hyperdense aortic walls, narrowed aorta, gas in the mediastinum, and hepatomegaly compared to the ROSC group. Conclusions: Although WBCT did not provide the direct cause of OHCA, it clarified several indicative findings for non-ROSC. These imaging findings could support clinical decision-making, offering objective criteria for discontinuing resuscitation in pediatric OHCA cases where prehospital ROSC is absent.

Abstract-Digital Phase Plane is presented in this paper. For constant input second order digital systems with arbitrary initial conditions for arbitrary quantizaters, this digital phase plane shows, in plot form, the state trajectory and the asymptotic stability, including the existence and the position of arbitrary period limit cycles.

Nickel-base superalloys like VDM 780 may possess a high content of Cr and Co. This influences solution energies of phase-forming elements like Al and Ta (γ′-phase), Nb (γ′′- and δ-phase), and Ti (η-phase). We perform density functional theory studies of a nickel matrix at 0 K with high concentrations of either Co and Cr and calculate the influence of these elements on solution energies. In the case of Co, the solution energy can be predicted well by the nearest-neighbor interaction in the Co-rich matrix. For Cr, the effect is more complicated because Cr has a larger ionic radius and changes the magnetic state of the material. The effect of a Cr-rich matrix on the energy of Co is dominated by magnetic effects, interactions with the other elements by elastic deformation of the lattice.

A one-dimensional numerical overland flow model based on the cascade plane theory was de-veloped to estimate rainfall-induced runoff and soil erosion on converging and diverging plane surfaces. The model includes three components: (i) soil infiltration using Horton’s infiltration equation, (ii) overland flow using the kinematic wave approximation of the one-dimensional Saint-Venant shallow water equations for a cascade of planes, and (iii) soil erosion based on the sediment transport continuity equation. The model’s performance was evaluated by comparing numerical results with laboratory data from experiments using a rainfall simulator and a soil flume. Four independent experiments were conducted on converging and diverging surfaces under var-ying slope and rainfall conditions. Overall, the numerically simulated hydrographs and sediment graphs closely matched the laboratory results, showing the efficiency of the model for the tested controlled laboratory conditions. The model was then used to numerically explore the impact of different plane soil surface geometries on runoff and soil loss. Seven geometries were studied: one rectangular, three diverging, and three converging. Constant soil surface area, rainfall intensity, and slope gradient were maintained in all simulations. Results showed that increasing convergence angles led to higher peak and total soil loss, while decreasing divergence angles reduced them.

In the Republic of Serbia, no comprehensive scientific multimethod research has been conducted to identify weaknesses and opportunities for improving the disaster risk management system. Regarding that, in the paper, author presents project description ,,Strengthening Integrated Disaster Risk Management System in Serbia - DISARIMES” which shall enable strengthening the disaster risk management system through research, development and innovative solutions implementation in the preparation, mitigation, response, remediation and post-disaster phases. The scientific importance of the projected research is reflected in the creation of assumptions for the advancement of theoretical and empirical knowledge in the scientific field of disaster risk management, bearing in mind that it is a relatively young scientific discipline in Serbia. The results of the project research will make it easier for decision makers in Serbia to understand the shortcomings of the system, but also provide innovative opportunities to improve their functioning in conditions of increasingly frequent and serious disasters. Establishing a scientific and professional society in the field of disaster risk management will create sustainable and necessary conditions for the transfer and improvement of knowledge and experience of importance for raising the level of operability of the system of protection and rescue of the Republic of Serbia in the event of disasters. A key contribution of the research findings will be to create a sustainable knowledge base that will be supported by the relevant amount of information regarding innovative capabilities and solutions identified as necessary to raise social resilience to a much higher level. In order to achieve the set goals, DISARIMES makes it possible, through a large number of SWOT analyses and other multimethod studies, to clearly identify and systematize the objective deficiencies and barriers encountered by the disaster risk management system in Serbia in all its stages before, during and after disasters, to identify and implement the appropriate solutions based on this. The objectives of the project are: to assess and identify strengths (advantages), weaknesses (disadvantages), opportunities (innovation potential) and threats for the disaster risk management system in Serbia; to develop and update RDI (research, development, innovation) Roadmap – knowledge databases with innovative solutions and other relevant information for improvement of the disaster risk management system; to fully deploy the DISARIMES scientific-professional network involving a broad range of the disaster risk management scientists and civil protection professions and organisations; to prepare the ground for the disaster risk management policy innovations.

Increasing traffic loads and changes in code provisions lead to deficits in shear and flexural capacity of many existing highway bridges. Therefore, a lot of structures in Europe and North America are expected to require refurbishment and strengthening in the future. This projection is based on the current condition of many older road bridges. Different strengthening methods for bridges exist to extent their service life, all having specific advantages and disadvantages. By applying a thin layer of carbon textile reinforced mortar (CTRM) to bridge deck slabs and the webs of prestressed concrete bridges, the fatigue and ultimate strength of these members can be increased significantly. The CTRM-layer is a combination of a corrosion resistant carbon fibre reinforced polymer (CFRP) fabric and an efficient mortar. In this paper, the strengthening method and the experimental results obtained at RWTH Aachen University are presented.

Most historical buildings and structures in Oman were built using unreinforced stone masonry. These structures have deteriorated due to ageing of materials, environmental degradation, and lack of maintenance. This research investigates the physical, chemical, and mechanical properties of local building materials and the results of an experimental study on the out-of-plane bending effectiveness of an innovative strengthening technique applied to existing masonry walls. The technique consists of the application on one face of the walls of a basalt textile-reinforced sarooj mortar (TRM). Four-point bending tests of full-scale masonry samples (1000 mm width, 2000 mm height, and 350 mm depth) were carried out using one unreinforced specimen and three different cases of reinforced specimens. The performance of unreinforced and reinforced specimens was analyzed and compared. The strengthened specimens were able to resist moments of out-of-plane bending 2.5 to 3 times greater than those of unreinforced specimen (160%- 233% increase). Moreover, the strengthened walls were able to sustain higher deformations (deflections) than the unreinforced specimen ranging from 20%-130%. The results showed that using TRM was effective for the out-of-plane strengthening of stone masonry using a local material (sarooj) that is compatible with existing stone masonry building materials.

Probability is an open question in the ontological interpretation of quantum mechanics. It has been discussed in some trajectory interpretations such as Bohmian mechanics and stochastic mechanics. New questions arise when the domain of probability extends to the complex space, including the generation of complex trajectories, the definition of the complex probability, the relation of the complex probability to the real quantum probability, and so on. The complex treatment proposed here applies the optimal quantum guidance law to derive the stochastic differential (SD) equation governing the particle’s random motions in the complex plane. The ensemble of the complex quantum random trajectories (CQRTs) solved from the complex SD equation is used to construct the probability distribution ρc(t,x,y) of the particle’s position over the complex plane z=x+iy. The correctness of the obtained complex probability is confirmed by the solution of the complex Fokker-Planck equation. The significant contribution of the complex probability is that it can be used to reconstruct both quantum probability and classical probability, and to clarify their relationship. Although quantum probability and classical probability are both defined on the real axis, they are obtained by projecting complex probability onto the real axis in different ways. This difference explains why the quantum probability cannot exactly converge to the classical probability when the quantum number is large.

In the paper, the author finds bounds of the sine and cosine along a circle on the complex plane in terms of two double inequalities for the norms of the sine and cosine along a circle on the complex plane.

In the paper, the author discusses and computes bounds of the sine and cosine along straight lines on the complex plane.

The geometry of structural members can influence the fatigue crack growth rate. In the paper, the T-stress depending on the element's geometry is used to quantify the effect of geometry on the fatigue crack growth rate. A series of fatigue tests on three-point bending specimens with different initial crack lengths were conducted. As a result, the dependence of the crack growth rate on the T-stress value was obtained.

This article explores matter collineations (MCs) of static plane-symmetric spacetimes, considering the stress-energy tensor in its contravariant and mixed forms. We solve the MC equations in two cases: when the energy-momentum tensor is nondegenerate and degenerate. For the case of degenerate energy-momentum tensor, we employ a direct integration technique to solve the MC equations, which leads to an infinite-dimensional Lie algebra. On the other hand, when considering the nondegenerate energy-momentum tensor, the contravariant form results in a finite-dimensional Lie algebra with dimensions of either 4 or 10. However, in the case of the mixed form of the energy-momentum tensor, the dimension of the Lie algebra is infinite. Moreover, the obtained MCs are compared with those already found for covariant stress-energy.

In recent years, drones have been used in a wide range of fields such as agriculture, transportation of goods, and security. Drones equipped with communication facilities are expected to play an active role as base stations in areas where ground base stations are unavailable, such as disaster areas. In addition, asynchronous operation is being considered for local 5G in order to support all kinds of use cases. In asynchronous operation, cross-link interference between base stations is an issue. This paper attempts to reduce the interference caused by the drone network by introducing circularly polarized antennas. Numerical analyses are conducted to validate the effectiveness of the proposed system, where SIRs (Signal-to-Interference Ratio) are shown to be improved significantly as the numerical evaluation results.

Background: Smad4, a critical tumor suppressor gene, plays a significant role in pancreatic biology and tumorigenesis. Genetic background and sex are known to influence phenotypic outcomes, but their impact on pancreatic weight in Smad4-deficient mice remains unclear. This study investigates the impact of Smad4 deficiency on pancreatic weight in F1 mice from diverse Collaborative Cross (CC) lines, focusing on the influence of genetic background and sex. Methods: F1 mice were generated by crossbreeding female CC mice with C57BL/6J-Smad4tm1Mak males. Genotyping confirmed the presence of Smad4 knockout alleles. Mice were housed under standard conditions, euthanized at 80 weeks, and their pancreatic weights were measured, adjusted for body weight, and analyzed for effects of Smad4 deficiency, sex, and genetic background. Results: The overall population of F1 mice showed a slight but non-significant increase in adjusted pancreatic weights in heterozygous knockout mice compared to wild-type mice. Sex-specific analysis revealed no significant difference in males but a significant increase in adjusted pancreatic weights in heterozygous knockout females. Genetic background analysis showed that lines CC018 and CC025 substantially increased adjusted pancreatic weights in heterozygous knockout mice. In contrast, other lines showed no significant difference or varied non-significant changes. The interplay between genetic background and sex further influenced these outcomes. Conclusion: Smad4 deficiency affects pancreatic weight in a manner significantly modulated by genetic background and sex. This study highlights the necessity of considering these factors in genetic research and therapeutic development, demonstrating the value of the Collaborative cross-mouse population in dissecting complex genetic interactions.

In recent years, with the increase in maritime trade, the necessity of increasing the capacities of the ports has emerged. However, while it is planned to increase the capacities of the ports, it is important that the port continues to operate at the same time. In this respect, the old port structures should not be damaged during the capacity increase. In this study, the strengthening of a port in Guinea is discussed as a case study. In the study, the existing quay wall was evaluated, and geotechnical and structural alternatives of the new structure to be built for capacity increase were evaluated. A combined system was designed as a pile foundation and a reinforced foundation with plastic piles so as not to damage the existing quay wall. The pile capacities obtained as a result of the analyses were verified by loading tests.

The quality of the environment affects human behavior, the micro-communities of human beings need creative thinking and ideas. Social environments have a significant impact on collective behaviors and social interactions. Nowadays achieving social indicators in housing with a sustainable approach is one of the goals that have been considered. The most important issue in the field of research is recognizing and examining the value of spaces in residential environments to achieve social life, in which it leads human to be social in public residential spaces. Paying attention to social relations with neighbors and people to create Social relationships are proportionate to the presence of individuals in their realm of life. The concept of neighborhood is being responsible for creating social relationships, influencing people living in the complex and community-based life. In this research, by satisfying the human need to communicate and interact with others, creating collective spaces in different scales such as commercial and recreational spaces in residential complexes, the presence of people in these spaces leads to the socialization of collective space and the factor in which the space achieves success. By explaining and identifying the components of socialization in the collective spaces of residential complexes, such spaces can be prepared for the presence of people in the space.

Efficient thermal management of modern electronics requires the use of thin films with highly anisotropic thermal conductivity. Such films enable the effective dissipation of excess heat along one direction while simultaneously providing thermal insulation along the perpendicular direction. In this study, we investigate the thermal conductivity of bilayer graphene (BLG) sheets using non-equilibrium molecular dynamics, examining both in-plane and cross-plane thermal conductivities. The in-plane thermal conductivity of 10 nm × 10 nm BLG with zigzag and armchair edges at room temperature is found to be around 204 W/m.K and 124 W/m.K, respectively. The in-plane thermal conductivity of BLG increases with sheet length. For all sizes, BLG with a zigzag edge exhibits higher thermal conductivity than that of the armchair edge, with this difference becoming more pronounced as the lengths of the sheets increase. In addition, increasing temperature from 300 K to 600 K decreases the in-plane thermal conductivity of a 10 nm× 10 nm zigzag BLG by about 34%. Similarly, the application of a 12.5% tensile strain induces a 51% reduction in its thermal conductivity compared to the strain-free values. Armchair configurations exhibit similar responses to variations in temperature and strain, but with less sensitivity. Furthermore, the cross-plane thermal conductivity of BLG at 300 K is estimated to be 0.05 W/m·K, significantly lower than the in-plane results by approximately four orders of magnitude. The cross-plane thermal conductance of BLG decreases with increasing temperatures, specifically, at 600 K, its value is almost 16% of that observed at 300 K.

Fracture analysis of reinforced concrete deep beam strengthened with carbon fiber-reinforced polymer (CFRP) plates was carried out. The present research aims to find out whether the crack propagation in a strengthened deep beam follows linear elastic fracture mechanics (LEFM) theory or nonlinear fracture mechanics theory. To do so, a new energy release rate based on nonlinear fracture mechanics theory was formulated on the finite element method and the discrete cohesive zone model (DCZM) was developed in deep beams. To validate and compare with numerical models, three deep beams with rectangular cross-sections were tested. The code results based on nonlinear fracture mechanics models were compared with experimental results and ABAQUS results carried out based on LEFM. The predicted values of initial stiffness, yielding point and failure load, energy absorption, and compressive strain in the concrete obtained by the proposed model were very close to the experimental results. However, the ABAQUS software results have greater differences with the experimental results. For example, the predicted failure load for the shear-strengthened deep beam using the proposed model has only 6.3% differences compared to the experimental result. However, the predicted failure load using ABAQUS software based on LEFM has greater differences (25.1%) compared to the experimental result.

Italian, Spanish, French vs German, Austrian or Norwegian COVID-19 tracks? Antibiotics might have a partial impact on COVID-19 death rates in various countries. Our working hypotheses based on recent publications is that that antibiotics may be a major factor that negatively affects patients’ immune system during viral infections. We are all aware that there is no specific and effective medical treatment for COVID-19 so far. However, we know that our immune system is the only efficient weapon that fights against this syndrome right now. In fact, antibiotics are very often prescribed to prevent secondary infections following an antiviral immune response. Various antibiotic therapies have also been commonly applied to support COVID-19 treatments in China and Italy. Unfortunately, the frequent antibiotic off-site targets include mitochondria that are genetically and evolutionary closely linked to bacteria. Mitochondria are multifunctional organelles responsible for bioenergetics in nearly all our cells, acting as signaling hubs in antiviral and antibacterial immune responses. Several studies have demonstrated that mitochondria are vulnerable to antibacterial treatments, interrupting their physiology. Inhibition of these processes by antibiotics might render the immune system less capable of fighting acute COVID-19 viral infections. Some antibiotics, including those prescribed for COVID-19 in Wuhan, have been shown to inhibit the synthesis of mitochondrial DNA. The question is whether antibiotics support such a treatment or weaken patient immune responses in this case. This hypothesis should be evaluated based on comparative clinical data that seem to be unavailable at the moment. Possibly the COVID-19 risk group should be extended to all patients being treated with antibiotics, including those who finished antibiotic therapies days up to several months before SARS-CoV-2 infection. We therefore urge health service response groups to evaluate the impact of antibiotics on COVID-19 recovery vs death retrospective data. We would like to motivate international, national and local health authorities to share available clinical treatment data, discuss and optimize treatment strategies.

To enhance the uplift capacity and facilitate the installation of multi-row perfobond connectors at shallow burial depths, this study puts forward a novel notched T-perfobond connector. The design incorporates an integrated flange at the bottom of the connector and a notch at the edge of the hole. Through pull-out model tests on four notched T-perfobond connectors, this research investigates their failure mechanisms and pull-out capacities. Utilizing the explicit dynamics method in Abaqus, a finite element model of the pull-out resistance test for the notched T-perfobond connector is established and verified against experimental data. Furthermore, a detailed parametric analysis involving 54 models is conducted, examining crucial parameters such as rib dimensions, hole geometry, flange size, notch width, bar diameter, and material properties. Based on the combined experimental and numerical results, the paper assesses the suitability of current formulas for calculating the pull-out capacity of perfobond connectors and proposes a refined calculation method specifically for notched T-perfobond connectors. All the findings in this paper can serve as a reference in the design and construction of composite structures.

Our research aims to address the urgent need for retrofitting measures to enhance the resilience of damaged coupling beams in real-life scenarios. We conducted a series of tests on scaled-down prototype coupling beams, carefully adhering to similarity theory requirements to ensure accurate representation. The test results showed that the chord rotation capacities of different specimens with the same diagonal bundle varied significantly due to the difference in the confinement levels. The specimens with lower level of confinement were found to have less displacement capacity. When the specimens were strengthened by wrapping with GFRP after damage, it was observed that the increase in confinement level significantly increased the chord rotation capacities of all specimens. In addition, in the tests before the strengthening, the elongation behavior of the specimens is observed until the damage development reaches approximately 2% chord rotation. With the in-crease in chord rotation, the elongation behavior of the specimens stops with increasing damage and then shortening behavior is observed. After retrofitting, it was observed that the axial elongation continued in a limited manner depending on the location and size of the concrete separated from the beam core in the case of collapse before strengthening, and then the beam showed a shortening behavior predominantly. After strengthening studies, our findings contribute valuable insights into the behavior and performance of damaged coupling beams, emphasizing the potential of urgent GFRP wrapping as a viable solution to enhance the seismic resilience of middle- and high-class buildings with structural walls after seismic events.

Interactive Planning Support Systems (PSS) implemented on a maptable are deemed suitable to support participatory planning processes. Through their interactive nature and user-friendly interface they are supposed to facilitate exchange of knowledge between stakeholders, consensus building among them, group learning processes, and thereby strengthen participation. We analyze in this systematic review, based on 16 case studies using interactive PSS, how such PSS have contributed to the goal of strengthening stakeholder participation. Results show that tools and applications have become more sophisticated in recent years and the goals of the studies changed from collaboratively designing interventions to observing and understanding how the application of such tools contributes to improved plan outcomes and group based learning. However, many case studies lack a proper framework and operationalization for investigating the impacts of the tools and applications on participation. Consequently, impacts on participation are assessed rather incidentally based on implicit assumptions and often no distinction is made between the different aspects of participation. In conclusion, further theoretical studies conceptualizing impacts of interactive PSS on participation are needed as well as empirical studies testing these impacts in real world case contexts with various groups of stakeholders.

Victor Vasarely’s (1906-1997) important legacy to the study of human perception is brought to the forefront and discussed. A large part of his impressive work conveys the appearance of striking three-dimensional shapes and structures in a large-scale pictorial plane. Current perception science explains such effects by invoking brain mechanisms for the processing of monocular (2D) depth cues. Here in this study, we illustrate and explain the local effects of 2D color and contrast cues on the perceptual organization in terms of figure-ground assignments, i.e. which local surfaces are likely to be seen as “nearer” or “bigger” in the image plane. Paired configurations are embedded in a larger, structurally ambivalent pictorial context inspired by some of Vasarely’s creations. The figure-ground effects these configurations produce reveal a significant correlation between perceptual solutions for “nearer” and “bigger” when no other monocular depth cues are given in the image. In consistency with previous findings on similar, albeit simpler visual displays, a specific color may compete with luminance contrast in resolving the planar ambiguity of a complex pattern context. Vasarely intuitively understood, and successfully exploited, this kind of subtle context effect in his art, well before empirical investigations had set out to study and explain their genesis in terms of information processing by the visual brain.

The purpose of this study is to investigate the failure mechanism and preventive strengthening methods of prefabricated full length small box girder (PSBG) under car explosion. After damage analysis during blast loads using the commercial software Autodyn, three strengthening methods are presented to improve the blast mitigation performance. The results show that the failure modes and bearing capacity are significantly different with various strengthening measures. Adhering U-shaped steel plate can effectively enhance the shear performance of PSBG under blast loads. Strengthening the bottom of the upper flange of box girder with steel plate can effectively mitigate the local bending failure, and enhance the overall flexural capacity during car explosion.

In-plane electro-optical switching (IPS) is a natural feature of a conventional planar aligned display cell based on deformed helix ferroelectric liquid crystal effect (DHFLC-effect) with sub-wavelength helix pitch if the tilt angle close to 40 degrees.

Swamp soil presents significant challenges for infrastructure development due to its soft and deformable nature, which compromises the stability of structures. Traditional wood pillars, while cost-effective and locally available, suffer from degradation caused by moisture and biological organisms. This study investigates various methods to strengthen wood pillars, focusing on the combination of wood and concrete pillars to enhance durability and load-bearing capacity in swamp soil environments. Laboratory experiments and field tests demonstrate that encasing wood pillars in concrete or using composite materials significantly improves their mechanical strength and resistance to deformation. The results highlight the potential of these techniques to provide sustainable and economical solutions for construction in swamp areas, ensuring greater stability and longevity of the infrastructure.

Spending on out-patient health care by citizens in limited resource countries has received little attention.The purpose of this study is to determine the predictors of household spending on out-patient expenses in a cross-sectional study in Kenya. We applied the GEE methods to determine the effect of various variables on outpatient care. We established that the best predictors for outpatient spending in Kenya are Age of the household head, wealth index, marital status and education, which had the lowest QICu of 976341.2. There were no differences on age in mean spending on outpatient care and was changing in a sinusoidal manner. The rich spend more on outpatient care, due to financial ability. Spending increased across the wealth quantiles while gender had a significant effect in the general performance of the models, it didn’t assist in lowering the QICu

CuAl8Fe5Ni4Zn4Sn1 (OF 2238) is a new lead-free copper alloy for plain bearing applications that was first officially presented in a scientific journal in 2020. Soon after its invention, the use of the alloy for connecting rod bushings in heavy duty internal combustion engines was promoted and validated with customers. The aim of this article is to describe the material properties of the new alloy in more detail than previously and explain how the advantageous properties of CuAl8Fe5Ni4Zn4Sn1 are generated. At the beginning of the article, the general development trends in the field of copper alloys for sliding applications are presented. This is followed by a presentation of the latest research results about CuAl8Fe5Ni4Zn4Sn, before concluding with a brief summary and future outlook, emphasizing on the fact that recent trends in copper-based sliding applications show great additional potential for further material developments.

Bubble (point defect) – a precursor of fuzz or under dense nanostructure formation is crystal lattice defect. Suitable selection of crystal lattice which inhibit Frenkel pair generation and intrinsically promotes self- interstitial solid solution strengthening contributes effectively towards making plasma facing material. For this, interstitial sites, their size, amount / fraction, positions, tendency of occupation and diffusion parameters (e.g. activation energies (Q), activation volumes) are determined. Fcc iron carbon alloys (austenitic stainless steels AISI / SAE 321, fcc structure, Pearson code cF4, space group Fm3̅m) are proposed as suitable candidates. Along with their room temperature fcc structure having 12 interstitial positions (4 octahedral, 6 coordination sites and 8 tetrahedral, 4 coordination sites / unit cell) to allow insertion of self (iron) atoms, they have excellent corrosion resistance, thermal conductivity, and non- magnetic properties. After their melting, casting, and machining to required dimensions and geometry, stabilizing heat treatment is applied to precipitate all carbon as TiC and prevent formation of Cr23C6 (sensitization). This resist heat and surface degradation and yield excellent architecture which not onlyinhibit Frankel pair generation but will also allow bulk assimilation or surface annihilation (loop punching) of this lattice point defect. A superior thermal, fluid, and structural design augment above. A second choice is presented as Co base superalloys owing to same fcc crystal structure and excellent properties (such as strength, dimensional stability, oxidation resistance) at high temperature.

Auto checkout has received more and more attention in recent years and this system automatically generates a shopping bill by identifying the picture of the products purchased by the customers. However, the system is challenged by the domain adaptation problem, where each image of the training set contains only one commodity, whereas the test set is a collection of multiple commodities. The existing solution to this problem is to resynthesize the training images to enhance the training set. Then the composite images are rendered using CycleGAN to make the image distribution of the training set and the test set more similar. However, we find that the detection boxes given by the ground truth of the common dataset contain a large part of the background area, the area will affect the training process as noise. To solve this problem, we propose a mask data priming method. Specifically, we redo the large scale Retail Product Checkout (RPC) dataset and add segmentation annotation information to each item in the training set image based on the original dataset using pixel-level annotation. Secondly, a new network structure is proposed in which we train the network using joint learning of detectors and counters, and fine-tune the detection network by filtering out suitable images from the test set. Experiments on the RPC dataset have shown that our method yields better results. we used an approach that reached 81.87% compared to 56.68% for the baseline approach which demonstrates that pixel-level information helps to improve the detection results of the network.

The present paper deals with the retrofitting of unreinforced masonry (URM) buildings, subjected to in-plane shear and out of-plane loading when struck by an earthquake. After an introductive comparison between some of the latest punctual and continuous active retrofitting methods, the authors focused on the two most effective active continuous techniques, the CAM system and the Φ system, which also improve the box-type behavior of buildings. These two retrofitting systems allow us to increase both the static and dynamic load-bearing capacity of masonry buildings. Nevertheless, information on how they actually modify the stress field in static conditions is lacking and sometimes questionable, in the literature. Therefore, we performed a static analysis in the plane of Mohr/Coulomb, with the dual intent to clarify which of the two is preferable under static conditions and whether the models currently used to design the retrofitting systems are fully adequate.

Monitoring of structures is one of the engineering challenges of the 21st century. At the same time, as a result of changes in the conditions of use, design errors, many building structures require strengthening. The article presents research on the development of the external strengthening carbon fiber textile with an option of self-sensing. The idea is based on the pattern of resistive strain gauge, where thread is provided in a zig-zag of parallel lines. Already the first laboratory tests showed the high efficiency of the system in the measurement of strains, but also revealed the sensitivity of measurement to environmental conditions. The article presents studies on the influence of temperature and humidity on the measurement. To separate those effects, resistance changes were tested on unloaded concrete and wooden samples. The models were placed in a climatic chamber and the daily cycle of temperature and humidity changes was simulated. The results of the research confirm preliminary observations. Resistivity growths with the temperature. This effect is more visible on concrete samples, presumably due to its greater natural humidity. The strain measurement with carbon fibers is very sensitive to temperature changes and application of this method in practice requires compensation.

The electronic structural evolution of LLM-105 crystal and the (101) plane of LLM-105 crystal under different pressures is investigated by the density functional theory (DFT) calculations and the surface properties of seven low-Miller-index planes of LLM-105 crystal were investigated in this study. The result demonstrates that the surface energy of (101) plane of LLM-105 is much smaller when compared with other low-Miller-index planes of LLM-105.In order to further investigate the stability of crystal structure and (101) plane of LLM-105 under different pressures, a series of pressures ranged from 0 GPa to 55 GPa were applied during the DFT calculation, and the result shows that the electronic structures of LLM-105 crystal and the (101) plane changed with the increase of external pressure and the evolution process of (101) plane is different from that of LLM-105 crystal structure.

Natural gas hydrate has gained significant attention in recent years. To safely and sustainably exploit the natural gas from gas hydrate-bearing sediments, it is crucial to understand the long-term mechanical characteristics of the hydrate reservoir. In this study, the influence of hydrate and fine particles on the strain rate dependence of hydrate-bearing sediments under plane strain conditions has been studied. The experimental results show that the strain rate dependency of the mechanical properties of hydrate-bearing sediments is positively correlated with hydrate saturation instead of the morphology of hydrate in sediments. The residual strength of hydrate-bearing sediments is primarily controlled by the hydrate saturation and is independent of the strain rate. Changes in hydrate saturation, and fines content, can affect the relationship between the strain rate and shear band angle. Finally, the local volumetric expansion effect of hydrate-bearing sediments without fines content is more significant and shows a strong strain rate dependence characteristic. Overall, this study provides valuable insights into the long-term mechanical characteristics of hydrate reservoirs. These insights can contribute to the development of a constitutive model of hydrate-bearing sediments with time-dependence in the future, and which is meaningful to the exploitation of natural gas hydrate.

In ancient buildings, timber members could need specific on-site interventions, including reinforcement or repair, sometimes inserting of reinforcing material into grooves routed in the original sound wood. Grooves number, positions and dimensions, and strengthening materials may differ, according to the desired increase of bending stiffness and strength. The Modulus-of-Elasticity (MOE) of each beam is of key importance, but the incisions can affect it, net of the reduction of the removed wood. In this study 12 old beams were accurately measured and their static and dynamic MOEs calculated before and after the grooves processing, to simulate the operations of typical reinforcing interventions. One groove was routed along the length of each beam and deepened progressively by three steps. Tests have showed how the MOE is affected by the groove depth, decreasing up to one third. The paper proves how the weakening effect of grooves on-site can be assessed with dynamic MOE and roughly predicted by means of visual survey. Grooves need for strengthening beams, must be carefully evaluated because of the variation of the actual mechanical properties, net to lost wood.

The Hertzian contact theory, as well as most of the other classical theories of normal and tangential contact, provides displacements and the distribution of normal and tangential stress components directly in the contact surface. However, other components of the full stress tensor in the material may essentially influence the material behaviour in contact. Of particular interest are principal stresses and the equivalent von Mises stress, as well as the gradient of the hydrostatic pressure. For many engineering and biomechanical problems, it would be important to find these stress characteristics at least in the contact plane. In the present paper, we show that the complete stress state in the contact plane can be easily found for axially symmetric contacts under very general assumptions. We provide simple explicit equations for all stress components and the normal component of the gradient of hydrostatic pressure in the form of one-dimensional integrals.

Knowing that biomolecules, such as β-amyrin and α-amyrin, have some pharmacological effects, the aim of this study was directed towards exploring the protective effect of a Tomato Peel and Seed Extract (TPSE) for its soothing function but also for its capacity to modulate the adrenal axis, involved in stress response. Ex vivo tests were carried out on skin explants to evaluate the effectiveness of TPSE formulated at 0.5% on Calcitonin Gene-Related Peptide (CGRP) and IL-10 release, Kappa Opioid Receptor (KOR) and Caspase 14 expression. An in vivo study combined a clinical evaluation of skin homogeneity, psychological parameter as well as analysis of salivary cortisol and dehydroepiandrosterone concentrations. All measurements were carried out at the beginning and after 28 days of applying a TPSE face cream. TPSE regulated not only the release of CGRP and Il-10, reflecting an anti-neurogenic and anti-inflammatory properties, but also modulated KORs. Twenty height days of TPSE application induced a significant decrease in intensity and extent erythrosis, a lower output of salivary cortisol and a significant increase in pleasant emotions when compared to placebo. These results provide encouragement to continue exploring the impact of cosmetic ingredient on psychophysiological parameters to improve skin health and well-being.

To understand the possibility of interaction between scientific experimenting and artistic drawing in the form of drawings made in notebooks, assumed is a common element, a spiritual property, and transference as a mechanism for causality. Scientists, scientific experiments and artistic drawings all have different merits. Here the concept ‘speaking out’ in its meaning of expressiveness is proposed to bridge these differences. Scientific action and artistic action cannot be compared directly. However, a common spiritual element will make the investigated object, experimental set-up and notebook drawings comparable in the sense of translations authorized by the physicist. They all then speak out from the same source. In this paper considered are recent drawings made by physicists during experimentation, in notebooks and diaries. Discussed is transferal causality between the physicist, the artistic drawing and all the relevant objects belonging to the experiment. Spiritual properties are introduced for the physicist being a person, and for the investigated object, the experimental set-up and the drawings as objects.

This paper presents the results of experimental and numerical investigations aimed at enhancing the flexural capacity of Precast Concrete Corbel Beam-Column Connections (PC-CBCC) using Fiber-Reinforced Plastic (FRP) sheets. The experimental study primarily focused on assessing the flexural capacity of pinned PC-CBCCs reinforced with FRP layers, comparing them to a moment-resisting connection. A series of half-scale specimens, including three PC-CBCCs with varying FRP configurations, were tested alongside one in-situ concrete fixed connection. The objective was to quantify the ultimate flexural capacity of PC-CBCCs reinforced by FRP sheets. The effects of FRP layer thickness, locations, and potential debonding were examined under unidirectional static tests while applying a constant axial compressive load to the columns and subjecting the beams to lateral loads until fracture. Additionally, a precise finite element model of the PC-CBCCs and a fixed joint was developed and verified to simulate nonlinear static analyses of the connections in ANSYS software. A comprehensive comparison was conducted to determine their responses by employing various FRP configurations and properties. The tests and numerical results demonstrate that wrapping PC-CBCCs with anchored FRPs can transform pin connections into moment-resistant joints. Moreover, critical design parameters such as bond length, thickness, and placement of FRP sheets, along with appropriate mechanical anchorage, are identified to prevent debonding and delamination.

Introduction Cone Beam Computed Tomography (CBCT) scans should be digitally oriented using a reference plane before being evaluated for patient growth and treatment outcome. Current orientation planes are usually dependent on the Porion points. Using more reliable landmarks than the Porion, we introduce the Acta plane and investigate its reliability as an alternative reference plane for cases in which the Porion point is inaccessible. Methods To test its reliability, a dental student and an orthodontist located sixteen skeletal and dental landmarks in sixteen CBCT scans, before and after reorientation. Also, four measurements were calculated based on these landmarks’ coordinates. The reorientation of these CBCT scans with the Acta plane was done by another dental student. Intraclass Correlation Coefficient (ICC) was calculated before and after orientation, intra- and inter-examiner. The data were tested for significance through the Shapiro Wilk test with a threshold set at 0.05. Through the ICC variation of the points’ coordinates, this article also evaluated the reliability of this plane with the t-paired and exact-sign tests. Results: The identification of landmarks was more reliable in the reoriented CBCT images than in the original images, with a significant increase of 0.012 in the median of the ICC. Linear and angular measures showed no significant differences between groups. Conclusion This plane is a reliable alternative for the orientation of CBCT images. The design of the Acta plane might allow the use of a smaller field of view and, consequently, a reduction in the radiation dose.

Indications of the passage of time are indirect reminders of our mortality. Humans have often responded to this discomforting thought by attempting, temporally at least, to escape its relentless march through the notion of a timeless present. This essay explores how architecture can assist us in that objective. It suggests that there are at least three different ways that buildings can offer us temporary psychological refuge from the progress of time. They can include the fascination of seemingly timeless natural movement patterns. They can recall archetypal environments, and they can isolate us from the external world of perpetual temporal progress.

This paper investigates the classical but yet intriguing question of modeling orthotropic RC floor systems endowed with lightening elements, by means of a uniform orthotropic slab, in order to describe accurately the building response under seismic loads. The simplified method, commonly adopted by engineers, based on the equivalence between the transverse stiffness of the RC elements of the real floor and those of the orthotropic slab is presented. A case study in which this simplified method is used is also provided. Then, an advanced finite elements (FE) based method to determine the elastic properties of the equivalent homogenized orthotropic slab is proposed. Based on the results obtained from the application of this method to a case study, a discussion on the adequacy of the simplified method is also provided.

This work analyzes the severity and risk associated with Automatic Dependent Surveillance-Broadcast (ADS-B) message drop out in Detect and Avoid (DAA) function of Unmanned Aircraft System (UAS). Performance assessment of the Universal Access Transceiver (UAT) ADS-B message implies that in some cases ADS-B fails to update within a specified update interval, which is referred to as drop out in this work. ADS-B is a fundamental surveillance sensor for both class 1 and class 2 DAA systems. Message loss or drop out has been found as one of the common limitations of the ADS-B system. The key feature of this study is incorporating the update rate of real ADS-B data transmitted from the manned aircraft. The data were received from the Grand Forks International Airport, North Dakota. Monte Carlo method has been adopted to resolve encounter scenarios in the presence of drop out. The change in the alert triggered by the UAS DAA in the presence of ADS-B drop out has been investigated. Furthermore, the risk matrices are created to quantify the associated risk with drop out affected alerts. Simulation results depict that both the duration of drop out and DAA look-ahead time affect the alert-triggering function of UAS. With a small look- ahead window and longer duration of drop out, the number of warning alerts increases. Also, alerts are affected more during an overtaking encounter than that of a head-to-head encounter. A system-level analysis is also carried out to recognize the potential reasons behind the ADS-B drop out.

This study investigated the fatigue properties and interfacial strengthening mechanisms of Al6061-to-Cu dissimilar welded joints via electromagnetic pulse welding (EMPW). The load-bearing capacity of the joints at discharge voltages of 14 kV and 16 kV was superior to that of 12 kV. Meanwhile, the fatigue life of 14 kV joints was one order of magnitude higher than that of 12 kV. The SEM observation on the fatigue fracture surface shows that the typical “tire-mark” fatigue striation just appeared on the 14 kV joint, indicating higher ductility for handling more extended plastic deformation. The high EBSD acquisition was achieved except for the transition zone due to the formation of ultra-fine nanocrystalline Al2Cu phase and amorphous phase, along with many dislocations. Dense low-angle grain boundaries (LAGBs) and refined grains are formed along the bonding interface. This indicates that severe plastic deformation induced dislocations to form the substructure in such an instant (40-60 μs) during the high-velocity collision. The interfacial strength is not only due to the continuous interfacial diffusion layer with a “wave-like” or “inverted hook-like” pattern but also benefits from refined grains along the interface and in the transition zone, as well as the hybrid amorphous-nanocrystalline microstructure, which strengthens the joint through increasing ductility induced by refined grains and regulating amorphous or nanocrystalline phases to affect the balance between strength and ductility of the Al/Cu joint.

In this study, Cu/Ni and Cu/Al multilayer thin films with individual layer thickness varying from 25 nm to 200 nm were deposited at room temperature and further annealed up to 300 ℃. The mechanical and microstructural properties of the multilayers were characterized by nanoindentation, x-ray diffraction, and scanning electron microscopy. Both systems exhibited an increase in hardness with increasing annealing temperature. However, the Cu/Ni system showed a gradual and moderate (up to 30%) hardness increase from room temperature to 300 ℃, while the Cu/Al system showed a sharp increase (~150%) between 125℃ and 200℃. This distinct strengthening behavior is attributed to solid solution formation in Cu/Ni and diffusion-activated intermetallic formation in Cu/Al.

In this investigation, Cu-Ni alloys for possible fixed dental prostheses (FDPs), with different aluminum additions were produced using vacuum atmosphere. Annealed alloys (He atmosphere) with low aluminum concentration showed a coarse dendritic structure, while samples with high aluminum concentration showed a refined dendritic structure. Structural defects analyses have shown a relative low vacancy concentrations. Hardness value increases approximately five times for the alloyed samples compared with the as-cast and unalloyed samples. Compression test results have shown a noticeable strengthening improvement, mainly in samples heat treated with 10 at % Al, while samples with 5 at % Al presented also acceptable resistance. Results are discussed in terms of dislocation mobility and hardening precipitation mechanism.

Background: Waterborne diseases pose a significant global public health threat, compelling enhanced comprehensive surveillance. This study investigates the current infectious disease and antimicrobial resistance (AMR) surveillance systems, including wastewater and environmental surveillance (WES), in three sub-Saharan African countries: Tanzania, Burkina Faso, and the Democratic Republic of the Congo (DRC). The three countries have their specificities regarding wastewater networks and logistic systems. So, emphasizing the need to strengthen existing disease surveillance, the paper advocates for incorporating WES systems specifically designed for countries' context to monitor waterborne and re-emerging pathogens, as well as AMR.Methods: National workshops were conducted to assess the current clinical and environmental surveillance systems and identify priority pathogens for new environmental monitoring. Data were collected through surveys from experts in academia, research, policy, and healthcare. Results: Prioritized pathogens for WES include waterborne (poliovirus, Salmonella Typhi, Vibrio cholerae), respiratory (influenza A&B, SARS-CoV-2), other (Measles and Rubella, Mycobacterium tuberculosis). Recommended AMR pathogens include drug-resistant Mycobacterium tuberculosis, Salmonella spp., methicillin-resistant Staphylococcus aureus, and extended-spectrum beta-lactamase and carbapenemase-producing E. coli. Tanzania, Burkina Faso, and the DRC employ DHSI2-based centralized electronic systems for clinical data collection, complemented by Excel and paper-based registries. The WES approach is commonly employed for monitoring poliovirus and rarely for AMR and other pathogens. Discussion and conclusions: WES is a valuable tool for early detection of locally circulating human-derived pathogens, aiding in outbreak detection, data-driven epidemic response, and prevention. The availability of WES results underscores the importance of effective sanitation for safeguarding human, animal, and environmental health. WES is a pivotal tool for integrated risk management, preventing waterborne outbreaks, protecting drinking water sources, and ultimately gaining various UN Sustainable Development Goals. The study highlights the importance of customized WES systems in line with each country's context, emphasizing localized approaches for effective monitoring of waterborne pathogens and AMR.

Context: A clinical video telehealth (CVT) program was implemented improve access and quality of dementia care to patients and their caregivers in rural areas. The program was offered as part of an established dementia clinic/geriatric primary care clinic in collaboration with five community-based outpatient clinics (CBOC’s) affiliated with the Tennessee Valley Healthcare System (TVHS) in middle Tennessee. Telehealth support was provided by a physician – social worker team visit. Methods: Telehealth training and equipment were provided to clinic personnel, functioning part-time with other collateral clinical duties. Patients and caregivers were referred by primary care providers and had an average of 1 to 2 CVT encounters originating at their local CBOC lasting 20 to 30 minutes. Clinical characteristics and outcomes of patients and caregivers receiving CVT support were collected by retrospective electronic medical record (EMR) review. Results: Over a 3-year period 45 CVT encounters were performed on patient-caregiver pairs, followed for a mean of 15 (1-36) months. Some 80% patients had dementia confirmed and 89% of these had serious medical comorbidities, took an average of 8 medications, and resided at a distance of 103 (76-148) miles from the medical center. Dementia patients included 33% with late stage dementia, 25% received additional care from a mental health provider, 23% took antipsychotic medications, 19% transitioned to a higher level of care, and 19% expired an average of 10.2 months following consultation. Caregiver distress was present in 47% of family members. Consult recommendations included 64% community-based long-term care services and supports (LTSS), 36% medications, and 22% further diagnostic testing. Acceptance of the CVT encounter was 98%, with 8770 travel miles saved. Conclusion: CVT is well received and may be helpful in providing dementia care and supporting dementia caregivers to obtain LTSS for high-need older adults in rural areas.

The serious impact of Adolescent’s Free Sex Behavior will affect their developmental task. Having proper education and having optimal sex counseling are related to sexual behavior in adolescents. The alternative for this phenomenon recently has involved adolescents participating as peer counselors because they are more susceptible to peer influence. Online peer counselor programs may promote progression into depth understanding of sexual behavior among adolescents. This paper provides an overview of the effect of peer counselors on reproductive health among adolescents. It describes many conceptual frameworks about free sex behaviors, risk factors among adolescents, and the role of peer counselors in improving health reproductive behavior among adolescents.

This paper elucidates the impact of uncertainty on the Markowitz asset allocation and how it performs. The findings imply that when evaluated out-of-sample, estimation errors in parameters might significantly affect how well an allocation performs. Numerous publications that address this ambiguity have been highlighted to emphasize our findings further. In our work, we compare these approaches to alternative allocation strategies and explain their performance in both expected and real out-of-sample events. We find that the Markowitz framework can be improved by using tactics that take uncertainty into account. Longer sample numbers, however, may not always translate into better outcomes. Applying a short-sale constraint can also enhance the initial portfolio. Finally, we find that even more basic approaches to asset allocation, such as equally weighted allocation, perform reasonably well.

Nurses focus more on curative aspects rather than health promotion and disease prevention, thus weakening primary health care and lessening engagement with the community. Providing a learning environment that can support the professional growth of nurses through engagement with local communities and educational institutions would strengthen primary health care in the community; however, this poses challenges due to the traditional mindset of nurses towards primary health care. This integrative review aimed to explore key features of the potential of the nursing center model as a contracting-out approach to strengthen primary health care services. This integrative review provides lessons for implementing the Nursing Centre model for any country, mainly where nurses are not fully utilized for health promotion and disease prevention.

Background: The ongoing outbreak of Coronavirus Disease 2019 (COVID-19) represents a major threat to human health, which impairs the functionality of several organs. One of the hardest challenges in the fight against COVID-19 is the development of wide-scale, effective, and rapid laboratory tests to control disease severity, progression, and possible sudden worsening. Monitoring patients in real-time is indeed highly demanded in this pandemic era when physicians need reliable and quantitative tools to prioritize patients’ access to intensive care departments. In this regard, salivary biomarkers are extremely promising, as they allow for a fast and non-invasive specimens’ collection, which can be repeated multiple times. Methods: We compare salivary levels of immunoglobulin A subclasses (IgA1 and IgA2) and free-light chains (FLC k and λ) in a cohort of 29 SARS-CoV-2 patients and 21 healthy subjects. Results: We found that each biomarkers differs significantly between the two groups, with p-values ranging from 10-8 to 10-4. The performance ranking of these markers, shows that λFLC level (p=1.4e-8) is the best-suited candidate to discriminate the two groups, with an accuracy of 0.94 (0.87-1.00 95% CI), a precision of 0.91 (0.81-1.00 95% CI), a sensitivity of 1.00 (0.96-1.00 95% CI) and a specificity of 0.86 (0.70-1.00 95% CI). Conclusion: These results suggest λFLC as an ideal indicator of patient conditions. This is more strengthened in consideration that λFLC half-life (approximately 6 hours) is significantly shorter than the IgA one (21 days): thus λFLC appears displaying the potential to effectively monitor patients fluctuation in real-time.

This study aims to introduce out of school activities (OSA) to high school PJOK teachers in Padang Pariaman District, West Sumatra Province, Indonesia. As is known, OSA is an alternative for students in fulfilling their movement needs, especially during the COVID 19 pandemic. Currently, students mostly stay at home, such as studying from home, to doing activities from home. So that there is minimal possibility of carrying out the movement activities recommended by WHO. The research method used is action research. This method gets a problem, then arranges problem-solving, conducts treatment, and finally evaluates. The research results show no teachers who have ever carried out of school activities (OSA); understanding, implementation, and evaluation are also not understood by the teachers. After being given the treatment, the teachers became more aware and understood about out of school activities, starting from understanding, implementing to evaluating what had to be done.

Precipitates are the primary source of strength for the Al-Mg-Si alloy. Aluminum alloy in the peak-aged state mainly contain β'' and β' precipitates. In the past, most of the literature only considered the strengthening effect of β''. Here we develop a single crystal intensity model including both precipitate enhancement effects for the first time. This model was subsequently implemented into a crystal plastic finite element method to model the uniaxial tensile process of a polycrystalline aggregate model of Al-Mg-Si alloy. The simulation results for uniaxial stretching are in good agreement with the experimental results, confirming that the constitutive parameters used for the single crystal strength model with two precipitates are based on realistic physical implications. Furthermore, by comparing the uniaxial tensile simulation results of a peak-aged alloy considering the actual precipitated phase composition of the alloy with those assuming that the precipitated phase is only the β'' phase, the predicted tensile strength of the former is around 5.65% lower than that of the latter, suggesting that the two kinds of precipitation should be considered separately when simulating the mechanical response of Al-Mg-Si alloy. It is highly expected that the present simulation strategy is not limited to the Al-Mg-Si alloys, and it can be equally applied to the other age-enhanced alloys.

Hollow and concrete-filled steel tubes (CFSTs) are widely used as columns in many structural systems and local buckling can occur when they are subjected to axial compression loading. The critical regions for the local buckling of the columns are near the ends of the column where the moments are the highest. To strengthen the critical regions of the CFSTs the CFRP provides a simple and effective method which used previously as an enhancement for both of strength and ductility. So, this study suggests investigating the axial load behaviour of CFST strengthened with CFRP using FE method after a verification study and then a various parametric studies were carried out to cover the effect of the CFRP layers, number, confinement length and position. The FE results proved that, one CFRP sheet with thickness equal to 1.2 mm was strengthened the composite column by 8.5%, two CFRP sheets with total thickness equal to 2.4 mm was strengthened the composite column by 23.5%, three CFRP sheets with total thickness equal to 3.6 mm was strengthened the composite column by 35.1% and four CFRP sheets with total thickness equal to 4.8 mm was strengthened the composite column by 44.5%. Moreover, this study proved that by strengthened the composite columns with CFRP sheets with different lengths, the axial load resistance was improved by 8.5%, 4.6%, 0.1% and 0.0% for length percentages 100%, 75%, 50% and 25% respectively.

In recent years, pedestrian re-identification has gained a lot of interest due to its importance for many purposes such as security and safety. Many types of solutions have been proposed to solve this problem, where the majority are based on a features extraction such Convolution Neural Networks (CNNs). These approaches assume that only the identities that are in the training data can be recognized. The pedestrians in the training data are called In distribution (ID). However, in real world scenarios, new pedestrians and objects can appear in the scene and the model should detect them as Out Of Distribution (OOD). In our previous study , we proposed a pedestrian re-identification based on von-Mises Fisher (vMF) distribution. Each identity is embedded in the unit sphere as a compact vMF distribution far from other identities distributions. The embedding is done through a base CNN. Recently, proposed a framework called Virtual Outlier Synthetic (VOS), that detects OOD based on synthesising virtual outlier in the embedding space in an online manner. Their approach assumes that the samples from the same object maps to a compact space. This assumption aligns with the vMF based approach. Therefore, in this paper, we revisited the vMF approach and merged with VOS in order to detect OOD data points. We present our approach to merge both frameworks. We conducted several experiments to evaluate our proposed framework. Results showed that our framework was able to detect new pedestrian that do not exist in the training data in the inference phase. It also slightly helped to improve the re-identification performance.

The purpose of this study was to assess the extent to which self-esteem and depression mediated the influence of internalized stigma on life satisfaction among Korean out-of-school youths. Cross-sectional data on 318 youths provided information on perceived stigma, self-esteem, depression, life satisfaction, and personal characteristics. A multinomial logistic regression analysis was followed by structured path analysis to investigate the mediation effects. Internalized stigma was negatively associated with life satisfaction. Self-esteem significantly mediated the influence of stigma on depression and the influence of depression on life satisfaction. Further, stigma directly and significantly influenced depression. This study demonstrated that self-esteem and depression were important to the relationship between internalized stigma and life satisfaction. Implications for possible policies and programs with the aim of helping out-of-school youths to integrate and lead successful satisfying lives are discussed.

Low back pain (LBP) is a health problem that affects 70-80% of the population in Western countries. Because of the biomechanical relationship between the lumbar region and the hip, it is thought that strengthening the muscles of this joint could improve the symptoms of people with LBP. The objective of the study is to evaluate the current evidence on the efficacy of hip strengthening exercises to reduce pain and disability in people with LBP. Clinical trials were collected from PubMed, PEDro, and Scopus databases published up to September 2022. Based on Preferred Reporting Items for Systematic Review and Meta-Analysis (PRISMA) guidelines and using CASpe and PEDro tools for methodological quality assessment, we selected studies that included hip strengthening exercises as part of LBP treatment and measured pain and/or disability parameters. Among the 966 records identified in the search, a total of 7 studies met the established selection criteria. Overall, participants who performed hip strengthening exercises had significantly improved in pain and disability. The methodological quality of the included studies was assessed as “good”. In conclusion, the addition of hip muscle strengthening exercises iterating LBP effectively improving pain and disability.