The efficiency and performance of Proton Exchange Membrane Fuel Cells (PEMFCs) are primarily influenced by ORR electrocatalysts. In recent years, atomically dispersed met-al-nitrogen-carbon (M-N-C) catalysts have gained significant attention due to their high active center density, high atomic utilization, and high activity. These catalysts are now considered the preferred alternative to traditional noble metal electrocatalysts. The unique properties of M-N-C catalysts are anticipated to enhance the energy conversion efficiency and lower the manufac-turing cost of the entire system, thereby facilitating the commercialization and widespread ap-plication of fuel cell technology. This article initially delves into the origin of performance and degradation mechanisms of Fe-N-C catalysts from both experimental and theoretical perspectives. Building on this foundation, the focus shifts to strategies aimed at enhancing the activity and durability of atomically dispersed Fe-N-C catalysts. These strategies encompass the use of bi-metallic atoms, atomic clusters, heteroatoms (B, S, and P), and morphology regulation to optimize catalytic active sites. The article concludes by detailing the current challenges and future pro-spects of atomically dispersed Fe-N-C catalysts.

Agriculture is an industry that heavily relies on the environment. The increasing frequency of ex-treme disasters attributable to climate change has adversely affected agricultural land and dis-rupted the stability of the supply of agricultural products. Therefore, we implemented a research program focused on current strategies for adapting to agricultural meteorological disasters. The primary goal was to actively promote disaster prevention information and techniques through information platforms and applications and to provide refined forecasting and an early warning system to enhance preparedness for and recovery from agricultural disasters. This initiative can transform passive mitigation into dynamic action by disseminating crucial information to farmers. We integrated meteorological data and crop characteristics to develop disaster prevention strate-gies for the predisaster, during-disaster, and postdisaster stages to empower farmers to implement autonomous disaster prevention, ensuring their profitability and minimizing the impact of disas-ters. This paper presents an agricultural disaster prevention system involving cross-disciplinary collaboration to establish an early warning system for crop disasters. However, the effectiveness of the early warning system relies on the availability of complete meteorological and crop infor-mation, necessitating high-density agricultural meteorological stations, refined weather forecast services, historical crop damage data, and ongoing research and development on disaster preven-tion technology. In the system, a diversified social media interface is used to provide local farmers with weather forecast information. When impending disasters are identified, the platform acti-vates disaster prevention measures to reduce agricultural losses. This article paper introduces Taiwan’s agricultural disaster prevention system as a complete disaster prevention strategy.

This article reports the two-step synthesis of NiFeO_x nanomaterials, their characterisation and bifunctional electrocatalytic activity measurements in alkaline electrolyte for metal-air batteries. The samples were mostly in layered double hydroxide at the initial temperature, but upon heat treatment, they were converted to NiFe₂O₄ phases. The electrochemical behaviour of the different samples was studied by linear sweep voltammetry and cyclic voltammetry on the glassy carbon electrode. The OER catalyst activity was observed for low mass loadings (0.125 mg cm⁻²), whereas high catalyst loading exhibited the best performance on the ORR side. The sample heat treated at 250 °C delivered the highest bi-functional oxygen evolution and reduction reaction activity (OER/ORR) thanks to its thin-holey nanosheet like structure with higher nickel oxidation state at 250 °C. This work further helps to develop low-cost electrocatalyst development for metal-air batteries.

Two methods for Pd nanoparticle synthesis were explored with three different carbide-derived carbon (CDC) support materials of which one was nitrogen-doped. These materials were studied for oxygen reduction reaction (ORR) in 0.1 M KOH solution. The prepared CDC/Pd catalysts were characterized using TEM, XRD and XPS. Using these methods, we can observe the influence of support materials for one-pot synthesis methods as we use the standard citrate method and polyol method with polyvinylpyrrolidone (PVP) as a capping agent. Comparing the two methods N-doping of carbon material resulted in smaller nanoparticles only in the case of citrate synthesis, suggesting that the influence of support is weaker using polyol method. Citrate method on CDC1, which was predominantly microporous led to a higher degree of agglomeration and larger particle formation in comparison to CDC2 and CDC3 supports, which possessed higher degree of mesoporosity. Smaller Pd particle sizes were achieved using citrate and NaBH4 in comparison to the ethylene glycol-PVP method. CDC2 and CDC3 did not show significant difference suggesting that the N-doping did not have much of an influence on the ORR. Highest SA value was observed on CDC1/Pd_Cit, which could be attributed to formation of larger particles and agglomerates.

Increasing the loading density of nanoparticles on carbon support is essential for making Pt-alloy/C catalysts practical in H2-air fuel cells. The challenge lies in increasing the load-ing while suppressing the sintering of Pt-alloy nanoparticles. This work presents a 40% Pt-weighted sub-3 nm PtCo/C alloy catalysts via a simple incipient wetness impregnation method. By carefully optimizing the synthetic conditions such as Pt/Co ratios, calcination temperature and time, the size of supported PtCo alloy nanoparticles is successfully con-trolled below 3 nm, and a high electrochemical surface area achieves of 94 m2/g is achieved, which is 2.8 times of commercial PtCo/C-TKK catalysts. Demonstrated by elec-trochemical oxygen reduction reaction, PtCo/C alloy catalysts present an enhanced mass activity of 0.45 A/mg at 0.9 V vs. RHE, which is 1.7 times that of PtCo/C-TKK catalyst. Therefore, the developed PtCo/C alloy catalyst can potentially be a highly practical cata-lyst for H2-air fuel cells.

Green synthesis of silver nanoparticles (AgNPs) using raw Whey has never been reported. Silver nanoparticle formation involves a reduction reaction of silver salt solution with Whey extract. Extract and metal salt concentrations, and temperature can control this reaction. In this work, incubation period, extract, AgNO3, and NaOH concentrations were used as the independent factors using central composite design under response surface methodology. The aim was to elucidate the influence these factors have on the measured UV-Vis absorption spectra fitted with a Voigt function, and to optimize the conditions for nanoparticle formation. The fitting parameters, peak wavelength (λ0), peak area (A), and Full Width at Half Maximum (FWHM), were the responses. Silver nanoparticle formation was only possible in an alkaline environment (pH 10). The peak wavelength and the FWHM are influenced mainly by extract and AgNO3 concentrations. In contrast, the peak area is influenced by a total of 33.54 % from the interaction terms of AgNO3 and extract concentrations with NaOH. Metallic AgNPs were formed for the following parameter ranges: a) Whey (0.4 – 1.6 % v/v), b) AgNO3 (0.15 – 0.6 mM), c) NaOH (10 – 50 mM), and d) Time (20 – 60 min). Silver oxide nanoparticles were also observed.

This research investigates the difference on the products obtained through two hydrothermal carbonization treatments. Our aim is to synthesize metal-free, carbon-based catalysts for the Oxygen Reduction Reaction (ORR) to serve as efficient and cost-effective alternatives to plati-num-based catalysts. Catalysts synthesized using the traditional hydrothermal approach exhibit a higher electrocatalytic activity for ORR in alkaline media, despite a more energy-intensive pro-duction process. The superior performance is attributed to differences in particle morphology and to the chemical composition of the particle surfaces. The presence of functional groups on the surfaces of catalysts obtained via traditional approach significantly enhances ORR activity by fa-cilitating deprotonation reactions in an alkaline environment. Our research aims to be a reference for future investigations, shifting the focus to the fine-tuning of surface chemical compositions and morphologies of metal-free catalysts to enhance ORR activity.

In this paper, we first report that WO_x contained nanoalloys exhibit stable electrocatalytic performance in alkaline media, though bulk WO₃ are easy to be dissolved in NaOH solutions. Carbon supported oxide-rich Pd-W alloy nanoparticles (PdW/C) with different Pd:W atom ratios were prepared by reduction-oxidation method. Among the catalysts, the oxide-rich Pd0.8W0.2/C (Pd/W = 8:2, atom ratio) exhibits the highest catalytic activity for oxygen reduction reaction. The X-ray photoelectron spectroscopy data shows that ~40% of Pd atoms and ~60% of the W atoms are in their oxides form. The Pd 3d_5/2 peaks in oxide-rich Pd-W nanoalloys are positive shift compared with that of Pd/C, which indicates the electronic structure of Pd is affected by the strong interaction between Pd and W/WO₃. Compare to Pd/C, the onset potential of oxygen reduction reaction at the oxide-rich Pd_0.8W_0.2/C is positive shifted. The current density (mA·mg Pd⁻¹) at the oxide-rich Pd_0.8W_0.2/C is ~1.6 times of that at Pd/C. The oxide-rich Pd_0.8W_0.2/C also exhibits higher catalytic stability than Pd/C, which demonstrate that it is a prospective candidate for the cathode of fuel cells operated with alkaline electrolyte.

The aim of this work is the development of new nanostructured-gas-diffusion-layer (GDL) to improve the overall behaviour of Air-Cathode Single-Chamber-Microbial-Fuel-Cells (SCMFCs). The design of new nanostructured-GDL allowed exploiting all nanofibers ’intrinsic properties, such as high surface ratio to volume, high porosity, achieving a good oxygen diffusion into the proximity of catalyst layer, favouring thus the direct oxygen-reduction-reaction (ORR). Nanostructured-GDLs were prepared by electrospinning process, using layer-by-layer deposition to collect 2 nanofibers’ mats. The first layer was made of cellulose nanofibers able to promote oxygen diffusion into SCMFC. The second layer, placed outwards, was based on polyvinyl-fluoride (PVDF) nanofibers to prevent the electrolyte leakage. This nanostructured-GDL plays a pivotal role to improve the overall performance of Air-Cathode-SCMFCs. A maximum current density of (132.2 ± 10.8) mA m-2 was obtained, which is two times higher than the one reached with commercial-PTFE (58.5 ± 2.4 mA m-2), used as reference material. All results were analyzed in terms of energy recovery parameter, defined as ratio of generated power integral and the internal volume of devices, evaluating the overall SCMFC performance. SCMFCs with a nanostructured-GDL showed an energy recovery one order of magnitude higher than the one obtained with commercial-PTFE.

A typhoon-induced storm surge is considered one of the most severe coastal disasters in Taiwan. However, the combination of the storm surge and the astronomical tide called the storm tide can actually cause extreme flooding in coastal areas. This study implemented a two-dimensional hydrodynamic model to account for the interaction between tides and storm surges on the coast of Taiwan. The model was validated with observed water levels at Sauo Fish Port, Hualien Port, and Chenggong Fish Port under different historical typhoon events. The model results are in reasonable agreement with the measured data. The validated model was then used to evaluate the effects of the typhoon's intensity, bathymetric change, and the combination of the typhoon’s intensity and bathymetric change on the maximum storm tide and its distribution along the east coast of Taiwan. The results indicated that the maximum storm tide rises to 1.92 m under a typhoon with an intensity of a 100-year return period. The maximum storm tide increased from a baseline of 1.26 m to 2.63 m for a 90% bathymetric rise at Sauo Fish Port under the conditions of Typhoon Jangmi (2008). The combination of the intensity of a typhoon with a 100-year return period and a 90% bathymetric rise will result in a maximum storm tide exceeding 4 m, 2 m, and 3 m at Sauo Fish Port, Hualien Port, and Chenggong Fish Port, respectively. We also found that the distribution of the maximum storm tide on the east coast of Taiwan can expand significantly subject to the bathymetric rise.

Considering characteristics of high river density, special underlying surface in plain river network region, and municipal drainage system function, river network drainage unit model is proposed, which is defined as a region surrounded by main river or embankment. Flood storage variety and control projects regulation of small rivers in each unit is simulated. With drainage catchment as an object, according to its drainage capacity, simplified municipal drainage model was developed. Coupling river network drainage unit model, simplified municipal drainage model and 2D flood routing model, urban flood analysis model for plain tidal river network region was developed, which could be applied to analyzing flood from upstream river, storm surge and local rainfall. Demonstration research was carried out in Puxi flood protected area in Shanghai.

Density functional theory (DFT) calculations of hydrogen adsorption on titanium nitride had previously shown that hydrogen may adsorb on both titanium and nitrogen sites with a moderate adsorption energy. Further, the diffusion barrier was also found to be low. These findings may qualify TiN, a versatile multifunctional material with electronic conductivity, as electrode material for the hydrogen evolution reaction (HER). This was the main impetus of this work which aims to experimentally and theoretically investigate the electrocatalytic properties of TiN-layers that were processed on Ti substrate using reactive ion sputtering. The properties are discussed focusing on the role of oxygen defects introduced during the sputtering process on the HER. Based on DFT calculations, it is shown that these oxygen defects alter the electronic environment of the Ti atoms which entails a low hydrogen adsorption energy in the range of -0.1 eV; this leads to HER performances that match those of Pt-NPs in acidic media. When a few nanometr thick layer of Pd-NPs is sputtered on-top of the TiN-layer, the performance is drastically reduced. This is interpreted in terms of oxygen defects being scavenged by the Pd-NPs near the surface which is thought to reduce the hydrogen adsorption sites.

The design and fabrication of low-cost catalysts for highly efficient oxygen reduction is of paramount importance for various renewable energy-related technologies, such as fuel cells and metal-air batteries. Herein, we report the in situ growth of Fe3N nanoparticles encapsulated N-doped carbon nanotubes on the surface of flexible biomass-derived carbon cloth (Fe3N@CNTs/CC) via a simple one-step carbonization process. Taking advantage of its unique structure, Fe3N@CNTs/CC was employed as a self-standing electrocatalyst for oxygen reduction reaction (ORR) and possessed high activity as well as excellent long-term stability and methanol resistance in alkaline media. Remarkably, Fe3N@CNT/CC can directly play the role of both gas diffusion layer and electrocatalytic cathode in a zinc-air battery without additional means of catalyst loading, and display higher open circuit voltage, power density, and specific capacity in comparison with the commercial Pt/C catalyst. This work is anticipated to inspire the design of cost-effective, easy-preparation, and high-performance air electrodes for advanced electrochemical applications.

Water electrolysis is a compelling technology for the production of environmentally-friendly hydrogen, minimizing carbon emissions. The electrolysis process of water heavily relies on the effective and steady oxygen evolution reaction (OER) taking place at the anode. Herein, we in-troduce a highly promising catalyst for OER called CoSe2@NiFeOOH arrays, which are supported on a nickel foam. This catalyst, referred to as CoSe2@NiFeOOH/NF, is fabricated through a two-step process involving the selenidation of a Co-based porous metal organic framework and subsequent electrochemical deposition on a nickel foam. The CoSe2@NiFeOOH/NF catalyst demonstrates outstanding activity for the OER in an alkaline electrolyte. It exhibits a low over-potential (η) of 254 mV at 100 mA cm−2, a small Tafel slope of 73 mV dec−1, and excellent high stability. The high performance of CoSe2@NiFeOOH/NF can be attributed to the combination of the high conductivity of the inner layer and the synergistic effect between CoSe2 and NiFeOOH. This study offers an effective method for the fabrication of highly efficient catalysts for the OER.

Behavior of supported alloyed and de-alloyed platinum-copper catalysts, which contained 14% - 27% wt. of Pt, was studied in the reactions of methanol electrooxidation (MOR) and oxygen electroreduction (ORR) in 0.1 M HClO4 solutions. Alloyed PtCux/C catalysts were prepared by a multistage sequential deposition of copper and platinum onto a Vulcan XC72 dispersed carbon support. De-alloyed PtCux-y/C catalysts were prepared by PtCux/C materials pretreatment in acid solutions. The effects of the catalysts initial composition and the acid treatment condition on their composition, structure, and catalytic activity in MOR and ORR were studied. Functional characteristics of platinum-copper catalysts were compared with those of commercial Pt/C catalysts when tested, both in an electrochemical cell and in H2/Air membrane-electrode assembly (MEA). It was shown that the acid pretreatment of platinum-copper catalysts practically does not have negative effect on their catalytic activity, but it reduces the amount of copper passing into the solution during the subsequent electrochemical study. The activity of platinum-copper catalysts in the MOR and the current-voltage characteristics of the H2/Air PEMFC MEAs measured in the process of their life tests were much higher than those of the Pt/C catalysts.

Proton exchange membrane water electrolyzers (PEMWEs) for water electrolysis have received tremendous attention due to their immediate response, high proton conductivity, low ohmic losses and gas crossover rate. However, design high activity, economical and long-term durable electrocatalysts in an acidic environment is still the bottleneck to realize the large-scale commercialization of PEMWEs. Iridium-based materials represent one of the most promising classes of oxygen evolution reaction (OER) catalysts due to their intrinsic stability in acid media over ruthenium-based counterparts. However, only a few innovative approaches have been developed to synthesizing iridium-based catalysts (IBCs) in the past decade, mainly due to achieving high activity may deteriorate the stability of IBCs. Accordingly, various engineering strategies of optimizing IBCs have been proposed to address this issue, including doping engineering, morphology engineering, crystal phase engineering and support engineering. Herein, a critical overview focusing on various synthesis and modulation strategies of IBCs is presented, based on an in-depth understanding of the relationship between electronic structures, charge redistribution and activity as well as stability of the electrocatalysts. In addition, the unprecedented achievements in PEMWEs are summarized. The reaction mechanisms and future perspectives are critically discussed to inspire more rational design of IBCs toward practical applications.

Results are presented concerning the influence on the water splitting process of enantiopure tartaric acid present in bulk solution. Stainless steel and electrodeposited nickel are used as working electrode (WE) surface. The latter is obtained by electrodeposition on the two poles of a magnet. The influence and role played by the chiral compound in solution has been assessed by comparing the current values, in cyclic voltammetry (CV) experiments, recorded in the potential range at which oxygen evolution reaction (OER) occurs. In the case of tartaric acid and nickel WE a spin polarization of about 4 % is found. The use of the chiral environment (bulk solution) and ferromagnetic chiral Ni electrode allows for observing the OER at a more favourable potential: about 50 mV (i.e. a cathodic, less positive, shift of the potential at which the oxygen evolution is observed).

In this study, we created a series of N, S, and P-doped and co-doped carbon catalysts using a single graphene nanoribbon (GNR) matrix and thoroughly evaluated the impact of doping on ORR activity and selectivity in acidic, neutral, and alkaline conditions. The results obtained showed no significant changes in the GNR structure after the doping process, though changes were observed in the surface chemistry in view of the heteroatom insertion and oxygen depletion. Of all the dopants investigated, nitrogen (mainly in the form of pyrrolic-N and graphitic-N) was the most easily inserted and detected in the carbon matrix. The electrochemical analyses conducted showed that doping impacted the performance of the catalyst in ORR through changes in the chemical composition of the catalyst, as well as in the double-layer capacitance and electrochemically accessible surface area. In terms of selectivity, GNR doped with phosphorus and sulfur favored the 2e- ORR pathway, while nitrogen favored the 4e- ORR pathway. These findings can provide useful insights into the design of more efficient and versatile catalytic materials for ORR in different electrolyte solutions, based on functionalized carbon.

For efficient electrode development in an electrolysis system, Fe₂O₃, MnO, and heterojunction Fe₂O₃-MnO materials were synthesized via a simple sol-gel method. These particles were coated on a Ni-foam electrode, and the resulting material was used as an electrode to be used during an oxygen evolution reaction (OER). A 1000-cycle OER test in a KOH alkaline electrolyte indicated that the heterojunction Fe₂O₃-MnO/NF electrode exhibited the most stable and highest OER activity: it exhibited a low overvoltage (n) of 370 mV and a small Tafel slope of 66 mV/dec. X-ray photoelectron spectroscopy indicated that the excellent redox performance contributed to the synergy of Mn and Fe, which enhanced the OER performance of the Fe₂O₃-MnO/NF electrode. Furthermore, the effective redox reaction of Mn and Fe indicated that the structure maintained stability even under 1000 repeated OER cycles.

Oxygen evolution reaction (OER) is a key half-reaction in electrocatalytic water splitting. Large-scale water electrolysis is hampered by the commercial precious metal-based OER electrocatalysts owing to their high cost and slow kinetics. To address these issues, we present a facile one-pot room-temperature coprecipitation method to quickly synthesize carbon nanotubes-interconnected amorphous NiFe-layered double hydroxides (NiFe-LDH@CNT) as low-cost, efficient and stable OER electrocatalyst. NiFe-LDH@CNT hybrid catalyst delivers outstanding OER performance with a low onset overpotential of 255 mV and a small Tafel slope of 51.2 mV dec-1, as well as outstanding long-term stability. The terrific catalytic capability of NiFe-LDH@CNT can be associated with the synergistic effects of its room-temperature synthesized amorphous structure, bi-metallic modulation, and conductive CNT skeleton. The room-temperature synthesis can not only offer economic feasibility, but also obtain amorphous NiFe-LDH without crystalline boundaries, facilitating long-term stability during OER process. The bi-metallic nature of NiFe-LDH guarantees a modified electronic structure, providing additional catalytic sites. Simultaneously, the highly conductive CNT network fosters a nanoporous structure, facilitating electron transfer, O2 release and enriching catalytic sites. This study presents a strategy to purposefully design nanoarchitecture and facilely synthesize amorphous transition metal-based OER catalysts, ensuring the cost effectiveness, production efficiency, and long-term stability.

The poor conductivity and instability of layered dihydroxides (LDHs) limit their widespread application in oxygen evolution reaction (OER). In this study, the composite electrode of NiMn-LDHs, reduced graphene oxide (rGO) and nickel foam (NF), i.e., NiMn-LDHs/rGO/NF, was prepared by a hydrothermal method. When subjected to oxygen evolution reaction (OER) catalytic performance in a solution of 1 M KOH, the NiMn-LDHs/rGO/NF composite catalyst exhibited an overpotential of only 140 mV at a current density of 10 mA cm-2 and a Tafel slope of 49 mV dec-1, which is not only better than the comparing RuO2/NF catalyst, but also better than most of the Mn-based and the Ni–Fe containing bimetallic OER catalysts reported in the literature. The excellent electrocatalytic performance is ascribed to the efficient integration of ultrathin NiMn-LDHs sheets, thin-layered rGO and NF, contributing a lot to the decrease in charge transfer resistance and the increase in electrochemically active surface area. Moreover, NF plays a role of current collector and a role of rigid support for the NiMn-LDHs/rGO composite, contributing extra conductivity and stability to the NiMn-LDHs/rGO/NF composite electrode.

In recent years, cerium dioxide (CeO2) has attracted considerable attention owing to its remarkable performance in various applications, including photocatalysis, fuel cells, and catalysis. This study explores the effect of nickel (Ni) doping on the structural, thermal, and chemical properties of CeO2 nanorods, particularly focusing on oxygen vacancy-related phenomena. Utilizing X-ray powder diffraction (XRD), alterations in crystal structure and peak shifts were observed, indicating successful Ni doping and the formation of Ni2O3 at higher doping levels, likely due to non-equilibrium reactions. Thermal gravimetric analysis (TGA) revealed changes in oxygen release mechanisms, with increasing Ni doping resulting in the release of lattice oxygen at lower temperatures. Raman spectroscopy corroborated these findings by identifying characteristic peaks associated with oxygen vacancies, facilitating the assessment of Ni doping levels. Overall, this study underscores the substantial impact of Ni doping on CeO2 nanorods, shedding light on tailored catalytic applications through modulation of oxygen vacancies while preserving the nanorod morphology.

In an effort to enhance the efficiency and safety of open-pit mines, this study explores the optimization of end slope road parameters and slope structures, specifically focusing on unmanned driving lanes.A significant aspect of the study is the development of a truck trajectory offset model, which considers the different reaction times between automated sensors and human drivers in adapting to environmental changes. To test these concepts, the study uses numerical simulations to confirm the stability of the proposed end slope designs. Using Victory West Mine No. 1 as a case study, the research determines the optimized width for unmanned driving lanes and the maximum angle for safe steepening of end slopes. The findings indicate that the optimized unmanned lane width for NTE240 mining dump trucks is 1743 mm, allowing for a 2-degree increase in the slope angle at the south end slope. This optimization leads to a steep mining stripping volume of 3.2735 million m³ and a coal output of 2.49628 million tons, maintaining a stripping ratio of 1.31m³/t. These results demonstrate that the unmanned driving road width optimization not only ensures slope safety but also significantly boosts the economic benefits of steep mining in open-pit mines.

Iron-containing nickel sulfides, selenides, and sulfoselenides were synthesized via a simple two-step hydrothermal reaction (temperature 160 °C) for their application as electrocatalysts in the oxygen evolution reaction (OER) in an alkaline solution (1 mol L–1 KOH). The study demonstrated that iron-containing nickel cobalt sulfides and selenides exhibit superior OER performance with lower overpotentials compared to iron-free nickel cobalt sulfide and selenide, which highlights the significant role of iron in enhancing OER nickel cobalt electrocatalysts: Fe0.1Ni1.4Co2.9(S0.87O0.13)4, η50 = 318 mV; Fe0.2Ni1.5Co2.8(S0.9O0.1)4, η50 = 310 mV; Fe0.3Ni1.2Co2.5(S0.9O0.1)4, η50 = 294 mV; Fe0.6Ni1.2Co2.5(S0.83O0.17)4, η50 = 294 mV, Fe0.4Ni0.7Co1.6(Se0.81O0.19)4, η50 = 306 mV compared to Ni1.0Co2.1(S0.9O0.1)4, η50 = 346 mV and Ni0.7Co1.4(Se0.85O0.15)4, η50 = 355 mV (all values at current densities η50 of 50 mA cm–2). Furthermore, the iron-containing nickel cobalt sulfoselenide Fe0.5Ni1.0Co2.0(S0.57Se0.25O0.18)4 displayed exceptional OER performance with η50 = 277 mV, surpassing the benchmark RuO2 electrode with η50 = 299 mV. The superior performance of the sulfoselenide was attributed to its low charge transfer resistance (Rct) of 0.8 Ω at 1.5 V vs. the reversible hydrogen electrode (RHE). Moreover, the sulfoselenide demonstrated remarkable stability, with only a minimal increase in overpotential (η50) from 277 mV to 279 mV after a 20 h chronopotentiometry test. These findings suggest that trimetallic iron, nickel and cobalt sulfide, selenide and especially sulfoselenide materials hold promise as high-performance, cost-effective, and durable electrocatalysts for sustainable OER reactions. This study provides a valuable approach for the development of efficient electrocatalytic materials, contributing to the advancement of renewable energy technologies.

By planting LEDs on the surfaces of orifice baffles, a novel batch oscillatory baffled photoreactor (OBPR) together with polymer-supported Rose Bengal (Ps-RB) beads are used to investigate reaction kinetics of a photo-oxidation reaction between α-terpinene and singlet oxygen (1O2). In the widely used NMR data analysis for this reaction, α-terpinene and ascaridole are treated as a reaction pair, assuming kinetically singlet oxygen is in excess or constant. We have, for the first time, examined the validity of the method, discovered that increasing α-terpinene initially leads to an increase of ascaridole, indicating that the supply of singlet oxygen is in excess. Applying kinetic analysis, a pseudo first order reaction kinetics is confirmed, supporting this assumption. We have subsequently initiated a methodology of estimating the 1O2 concentrations based on the proportionality of ascaridole concentrations with respect to its maximum under these conditions. With the help of the estimated singlet oxygen data, the efficiency of 1O2 utilization and the photo efficiency of converting molecular oxygen to 1O2 are further proposed and evaluated. We have also identified conditions where further increase of α-terpinene has caused decreases in ascaridole, implying kinetically that 1O2 has now become a limiting reagent, the method of treating α-terpinene and ascaridole as a reaction pair in the data analysis would no longer be valid under those conditions.

Metal-organic frameworks (MOFs) are investigated for the oxygen evolution reaction (OER) due to their structure diversity, high specific surface area, adjustable pore size and abundant active sites. However, the poor conductivity of most MOFs restricts this application. Herein, through a facile one-step solvothermal method, the Ni-based pillared metal-organic framework [Ni2(BDC)2DABCO] (BDC = 1,4-benzenedicarboxylate, DABCO = 1,4-diazabicyclo[2.2.2]octane), its bimetallic nickel-iron form [Ni(Fe)(BDC)2DABCO] and their modified Ketjenblack (mKB) composites were synthesized and tested towards OER in an alkaline medium (KOH 1 mol L–1). A synergistic effect of the bimetallic nickel-iron MOF and the conductive mKB additive enhance the catalytic activity of the MOF/mKB composites. All MOF/mKB composite samples (7, 14, 22, 34 wt.% mKB) indicated much higher OER performances than the MOFs and mKB alone. The Ni-MOF/mKB14 composite (14 wt. % of mKB) demonstrated an overpotential of 294 mV at a current density of 10 mA cm–2 and Tafel slope of 32 mV dec–1, which is comparable with commercial RuO2 commonly used as a benchmark material for OER. The catalytic performance of Ni(Fe)MOF/mKB14 (0.57 wt% Fe) was improved further to an overpotential of 279 mV at a current density of 10 mA cm–2. The low Tafel slope of 25 mV dec–1 as well as a low reaction resistance due to electrochemical impedance spectroscopy (EIS) measurement confirm the excellent OER performance of the Ni(Fe)MOF/mKB14 composite. For practical applications, the Ni(Fe)MOF/mKB14 electrocatalyst was impregnated into commercial nickel foam (NF), where overpotentials of 247 and 291 mV at current densities of 10 and 50 mA cm–2, respectively, were realized. The activity was maintained for 30 h at the applied current density of 50 mA cm–2. The electrocatalytic system consisting of earth-abundant Ni and Fe metals only would be attractive for the development of efficient, practical and economical energy conversion materials for efficient OER activity.

Effects of oxygen content on microstructure and creep property of FGH96 superalloy were investigated. When oxygen content increased from 135ppm to 341ppm, prior particle boundary (PPB) rose from degree 2 to degree 3, and the size of γ′ phase on PPB enlarged from 1.07μm to 1.27μm, and MC carbide size grew from 77.4nm to 104.0nm. Meanwhile, the steady creep rate accelerated form 4.34×10-3 h-1 to 1.87×10-2 h-1, and the creep rupture life shortened from 176h to 94h, and the creep rupture mode transferred from intergranular and transgranular mixed fracture to along PPB fracture. During creep, the micro-twins formation and gliding will be restrained by ∑3 boundaries. FGH96 superalloy with higher oxygen content contains less ∑3 boundaries and its micro-twins cross slipped instead of single direction slip in lower oxygen content superalloy. Consequently, specimen with higher oxygen content creeped faster and raptured earlier.

As argued by ‘Declaration of Concrete Environment (2010)’ of Korea and ‘Declaration of Asian Concrete Environment (2011)’ of six Asian countries, concrete as a single material has lately shown extremely large impact on environmental issues such as climate change. Assessment of environmental impact from concrete material and production has considerable importance. Concrete is a major material used in the construction industry that emits a large amount of substances with environmental impacts during its life cycle. Accordingly, technologies for the reduction in and assessment of the environmental impact of concrete from the perspective of Life Cycle Assessment must be developed. At present, the studies in relation to greenhouse gas emission from concrete are being carried out globally as a countermeasure against climate change. In this study, a sustainable concrete mix design algorithm was designed using correlation analyses, and its carbon emission and cost reduction performances were assessed. Using correlation analyses, the concrete strength, w/b and s/a ratios, and CO₂ emissions were identified as major variables of concrete mix design that influenced other variables. Also, this study aims to evaluate the CO₂ emission reduction performance of the algorithm-deduced sustainable concrete mix design, and therefore, the CO₂ emissions of the sustainable concrete mix design are compared with those of the actual concrete mix design applied to the construction of the office building A in South Korea.

Attribute reduction is a core technique in the rough set domain and an important step in data preprocessing. Researchers have proposed numerous innovative methods to enhance the capability of attribute reduction, such as the emergence of multi-granularity rough set models, which can effectively process distributed and multi-granularity data. However, these innovative methods still have many shortcomings, such as how to deal with complex constraints and how to perform multi-angle effectiveness evaluations. Based on the multi-granularity model, this study proposes a new method of attribute reduction, namely using multi-granularity neighborhood information gain ratio as the measurement criterion. This method combines both supervised and unsupervised perspectives, and by integrating multi-granularity technology with neighborhood rough set theory, constructs a model that can adapt to multi-level data features. This model can select the optimal granularity level or attribute set according to the requirements. Finally, the proposed method is experimented with on 15 UCI datasets against six other attribute reduction algorithms. The experimental outcomes, upon analysis and comparative review, substantiate the reliability and consistency of the attribute reduction approach introduced in this study.

Using density functional theory (DFT), the density of states of NH4V3O8 (NVO) was analyzed pre and post-oxygen defects (Od) formation. The findings revealed a reduced bandgap in NVO after Od introduction, emphasizing the role of Od in enhancing conductivity of the material, thus improving its electrochemical attributes. Through the water bath method, both NVO and its oxygen-deficient counterpart, (NH4)2V10O25⸱8H2O (NVOd), were synthesized as potential cathode materials for aqueous zinc-ion batteries (AZIBs). Experimental outcomes resonated with DFT predictions, highlighting the beneficial role of oxygen defects in boosting electrical conductivity. Notably, the refined material displayed a remarkable capacity of 479.3 mAh g-1 at 0.1 A g-1, underscoring its promise for advanced energy storage solutions.

Polymer electrolyte membrane water electrolyser suffers mainly from slow kinetics regarding oxygen evolution reaction (OER). Noble metal oxides, like IrO2, RuO2, are generally more active for OER than metal electrodes, exhibiting low anodic overpotentials and high catalytic activity. However, issues like electrocatalyst stability under continuous operation and cost minimization through reduction of the catalyst loading are of great importance for the research community. In the present study, unsupported IrO2 of various particle sizes (different calcination temperatures) were evaluated for the OER and as anode electrodes for PEM water electrolyzers [1]. The elec-trocatalysts were synthesized by the modified Adams method [2][3] and the effect of calcination temperature on the properties of IrO2 electrocatalysts is investigated. Physicochemical charac-terization was conducted using X-ray Diffraction, BET, High-Resolution TEM and XPS analyses. For the electrochemical performance of synthesized electrocatalysts in the OER, cyclic voltammetry and linear sweep voltammetry were conducted in a typical 3-cell electrode configuration, using glassy carbon as working electrode, where the synthesized electrocatalysts were casted on, in 0.5 M H2SO4 solution. The materials, as anode PEM water electrolysis electrodes, were further evaluated in a typical electrolytic cell using Nafion®115 membrane as electrolyte and Pt/C as cathode elec-trocatalyst. The IrO2 electrocatalyst calcined at 400°C shows high crystallinity with 1.24 nm particle size, high specific surface area (185 m2 g-1) and a high OER activity of 177 mA cm-2 at 1.8 V as anode electrocatalyst for PEM water electrolyzer.

Compared with precious metal catalysts, non-platinum catalysts have the advantages of low cost and high performance. Among them, the activated carbon (AC) with a large specific surface area (SSA) can be used as a carrier or as a carbon source of nonprecious metal/carbon system catalyst at the same time. Therefore, this paper uses cheap pine peel bio-based materials to prepare large surface area activated carbon and then compound with cobalt phthalocyanine (CoPc) to obtain a high-performance cobalt/nitrogen/carbon catalyst. The merits include AC@CoPc composite catalysts are prepared by precisely controlling the composite proportion of AC and CoPc, the atomically dispersed Co nanoparticles form and synergistically with N promote the exposure of CoNx active sites, and the Eonset of the catalyst treated with a composite proportion of AC and CoPc of 1 to 2 at 800 °C (AC@CoPc-800-1-2) is 1.01 V, which is higher than Pt/C (20 wt%) catalyst. Apart from this, the stability is 87.8% in 0.1 M KOH after 20000 s testing in compared with other AC@CoPc series catalysts and Pt/C (20 wt%) catalyst. Considering from the performance and price of the catalyst in practical application, these composite catalysts combine biomass carbon materials with phthalocyanine series, which will be widely used in the area of nonprecious metal catalysts.

Abstract: Toxicity of emerging organic pollutants to photosystems of aquatic plants are still not well clarified. This study aimed to develop a novel ecotoxicological experimental protocol based on nanoscale electrochemical mapping of photosynthetic oxygen evolution of aquatic plants by SECM (scanning electrochemical microscopy). The protocol was also checked by confocal laser scanning microscopy (CLSM), the traditional Clark oxygen electrode method and chlorophyll fluorescence technique. The typical persistent organic pollutant 2,4-dichlorophenol (2,4-DCP) in water environment and the common aquatic Microsorium pteropus (M. pteropus) were chosen as the model organic pollutant and tested plant, respectively. It was found that the SECM method could well discriminated the responses of stoma micromorphology and spatial pattens of photosynthetic oxygen evolution on single stoma. The shape of stoma blurred with increasing 2,4-DCP concentration, which was in good agreement with the CLSM images. The dose-response curves and IC50 values obtained from the SECM data were verified by the data measured by the traditional Clark oxygen electrode method and chlorophyll fluorescence test. The IC50 value of single stoma oxygen emission of 24 h exposed plant leave, which was derived from the SECM current data (32535 μg L-1), was close to those calculated from the maximum photosynthetic efficiency (Fv/Fm) measured by chlorophyll fluorescence test (33963 μg L-1), and the Clark oxygen electrode method photosynthetic oxygen evolution rate (32375 μg L-1). The 72 h and 96 h 2,4-DCP exposure data further confirmed the reliability of the nanoscale stoma oxygen emission mapping methodology for ecotoxicological assessment. In this protocol, the procedures for how to collect effective electrochemical data and how to extract useful information from the single stoma oxygen emission pattern were well established. This study showed that SECM is a feasible and reliable ecotoxicological tool for evaluation of toxicity of organic pollutants to higher plants with unique nanoscale visualization advantage over the conventional methods.

Efficient oxygen evolution reaction (OER) electrocatalysts are highly desired in the field of water electrolysis and rechargeable metal-air batteries. In this study, a chelate polymer, composed of copper (II) and dithiooxamide, was used to derive an efficient catalytic system for OER. Upon potential sweep in 1M KOH, copper (II) centers of the chelate polymer were transformed to CuO and Cu(OH)2. The carbon-dispersed CuO nanostructures formed a nanocomposite which exhibits an enhanced catalytic activity for OER in alkaline media. The nanocomposite catalyst has overpotential of 280 mV (at 1 mA/cm2) and a Tafel slope of 81 mV/dec in 1M KOH solution. It has a seven-fold higher current than IrO2/C electrode, per metal loading. A catalytic cycle is proposed, in which, CuO undergoes electrooxidation to Cu2O3 that further decomposes to CuO with releasing oxygen. This work reveals a new method to produce an active nanocomposite catalyst for OER in alkaline media using a non-noble metal chelate polymer and a porous carbon. This method can be applied to the synthesis of transition metal oxide nanoparticles used in the preparation of composite electrodes for water electrolyzers and can be used to derive cathode materials for aqueous-type metal-air batteries.

Oxidative stress has been implicated in cellular senescence and aging, as well as in the onset and progression of many diverse genetic and acquired diseases and conditions. The search for biomarkers of oxidative stress has become relevant to many biomedical fields using many different methods and approaches. Fluorescence methodology is advantageous because of its simplicity and high sensitivity. Fluorescent probes are frequently used to investigate the role of reactive oxygen species in oxidative stress in experimental or clinical settings, often involving the use of flow cytometry and related single-cell based technologies. To assess the specific role of reactive oxygen species in oxidative stress studies by cytometric methodologies, it is essential to detect and characterize these species accurately. However, the detection and quantitation of individual intracellular ROS is still a challenge, but different and complementary strategies may focus on other endpoints of oxidative stress. In this review we present and discuss briefly the limitations and perspectives of such approaches. Based on our results, we also provide recommendations for proper design of cytometric studies of oxidative stress in order to prevent or minimize experimental errors..

Arylmagnesium and -calcium reagents are easily accessible, however, ether degradation processes limit the storability especially of the calcium-based heavy Grignard reagents. Ortho-bound substituents with phosphanyl donor sites usually block available coordination sites and stabilize such complexes. The reaction of bromo-2,6-bis(diphenylphosphanylmethyl)benzene (1a) with magnesium in tetrahydrofuran yields [Mg{C₆H₃-2,6-(CH₂PPh₂)₂}₂] (2) after recrystallization from 1,2-dimethoxyethane. However, the similarly performed reduction of bromo- (1a) and iodo-2,6-bis(diphenylphosphanylmethyl)benzene (1b) with calcium leads to ether cleavage and subsequent degradation products. α-Deprotonation of THF yields 1,3-bis(diphenylphosphanylmethyl)benzene. Furthermore, the insoluble THF adducts of dimeric calcium diphenylphosphinate halides, [(thf)₃Ca(X)(µ-O₂PPh₂)]₂ [X = Br (3a), I (3b)], precipitate verifying ether decomposition and cleavage of P-C bonds. Ether adducts of calcium halides [such as [(dme)₂(thf)CaBr₂] (4)] form supporting the initial Grignard reaction and a subsequent Schlenk-type dismutation reaction.

The conversion of CO2 into more synthetically flexible CO is an effective and potential method for CO2 remediation, utilization and carbon emission reduction. In this paper, the reaction of carbon-carbon dioxide (Boudouard reaction) was performed in a microwave fixed bed reactor using semi-coke (SC) as both the microwave absorber and reactant and was systematically compared with that heated in a conventional thermal field. The effects of the heating source, SC particle size, CO2 flow rate and additives on CO2 conversion and CO output were investigated. By microwave heating (MWH), CO2 conversion reached more than 99 %, while by conventional heating (CH), the maximum conversion of CO2 was approximately 29% at 900 °C. Meanwhile, for the reaction with 5 wt% Barium Carbonate added as a promoter, the reaction temperature was significantly reduced to 750 °C with almost quantitative conversion of CO2. Further kinetic calculations showed that the apparent activation energy of the reaction under microwave heating was 46.3 kJ/mol, which was only one-third of that observed under conventional heating. The microwave-assisted Boudouard reaction with catalytic barium carbonate is a promising method for carbon dioxide utilization.

This study aimed to evaluate the effects of Blazepod technology when incorporated with various training regimens on the essential elements of physical fitness in volleyball, such as agility, speed, visual response time, and vertical leap. Thirty-six participants (age :17.33±0.48 y, height: 183.78±6.34 cm, weight: 77.14±5.16 kg) were in-volved in this study. In randomized design, three equal groups with two experimental groups and one control group were involved in the study over a period of six weeks: (GE1) used Blazepod technology to workout at a low level; (GE2) used Blazepod technology to workout at a higher intensity; (CG) did not employ Blazepod technology, but it adhered to the same fundamental training curriculum. We conducted agility, speed, reaction time, and vertical jump tests before, midway and after the study to determine optimal training volume, intensity, and frequency. A significant main effect of time (P0.01), and time×group interaction (P>0.001) were found for all tests. Post hoc test showed that the two experimental groups gadget significantly improved in all performance variables (P

The reduction of Ce cations in CeO2 can be enhanced by its partial substitution by Fe cations. The enhanced reduction of Ce cations results in a considerable increase in the reaction rates for thermal water splitting reaction when compared to CeO2 alone. This mixed oxide has a smaller crystallite size when compared to CeO2 in addition to a smaller lattice size. In this work, two Fe-substituted Ce oxides are studied (Ce0.95Fe0.05O2 and Ce0.75Fe0.25O2) by core and valence level spectroscopy in their as-prepared and Ar-ions sputtered states. Ar-ions sputtering substantially increases Ce4f lines at about 1.5 eV below the Fermi level. In addition, it is found that the XPS Ce5p/O2s ratio is sensitive to the degree of reduction, most likely due to a higher charge transfer from the oxygen to Ce ions upon reduction. Quantitatively it is also found that XPS Ce3d of the fraction of Ce3+ (uo, u’ and vo, v’) formed upon Ar-ions sputtering and the ratio Ce5p/O2s lines are higher for reduced Ce0.95Fe0.05O2 than for reduced Ce0.75Fe0.25O2. XPS Fe2p showed however no preferential increase for Fe3+ reduction to Fe0 with increasing time for both oxides. Since water splitting was higher on Ce0.95Fe0.05O2 when compared to Ce0.75Fe0.25O2, it is inferred that the reaction centers for the thermal water splitting to hydrogen are the reduced Ce cations and not the reduced Fe cations. These reduced Ce cations can be tracked by their XPS Ce5p/O2s ratio in addition to the common XPS Ce3d lines.

Soot combustion experiments with 5%O2/He were conducted using model soot, and four distinct compositions of CexPr1-xO2-δ oxides were prepared, varying nominal cerium com-positions (x=0, 0.2, 0.3, and 1). The catalyst samples were comprehensively characterized using techniques such as XRD, Raman spectroscopy, HR-TEM, N2 adsorption at −196 °C, XPS, O2-TPD, H2-TPR, and work function measurements. The Pr-rich compositions, rang-ing from Ce0.3Pr0.7O2-δ to PrO2-δ, resulted in a significant increase in the total evolved O2 amounts and enhanced catalyst reducibility. However, a decrease in textural properties of the catalysts was noted, being particularly important for the pure praseodymia under the synthesis route conducted. The catalytic activity was investigated under two contact modes of mixing between soot and catalyst: loose and tight. The results revealed that the catalytic performance is associated with the surface contact in tight contact mode and with the combination of surface/subsurface/bulk oxygen mobility and the BET surface ar-ea in loose contact mode. Notably, the T10 and T50 parameters were achieved at much lower temperatures than the uncatalyzed soot combustion, even under loose contact conditions. Specifically, the 50% conversion was achieved at 511℃ and 538℃ for Ce0.3Pr0.7O2 and Ce0.2Pr0.8O2, respectively. While no direct correlation between catalytic activity and work function was observed a significant relationship emerges between work function values and the formation of oxy-gen vacancies, whatever the conditions used for these measurements. On the other hand, the ability to generate a high population of oxygen vacancies at low temperatures, rather than the direct activation of gas-phase O2, influences the catalytic performance of Pr-doped ceria catalysts, highlighting the importance of surface/subsurface oxygen vacancy generation, which was the parameter which showed better correlation with the catalytic activity, whatever the soot conversion value or the mode of contact considered.

Materials based on platinum metals with very good catalytic activity were tested in the reduction of p–nitrophenol (pNP) to p–aminophenol (pAP). The majority of presented catalytic materials are based on the adsorption of p–nitrophenol on the surface of the catalyst simultaneously with molecular hydrogen, coming from sodium borohydride in an aqueous medium, which reduces it. In the present paper, a catalytic material based on osmium dispersed in n–decanol or n–dodecanol is presented, which also works as an emulsion membrane, for the absorption of p–nitrophenol and molecular hydrogen at the n–alcohol aqueous solution interface. The hydrogenation of p–nitrophenol is carried out in a reaction and separation column in which the acid receiving phase emulsion is dispersed in the osmium nanodispersion, in n–alcohols. This emulsion circulates from the base of the column to its upper part in co-current or counter-current with the source phase consisting of p–nitrophenol and sodium borohydride. Experiments show that the circulation of counter-current phases is superior to that in co-current, and the emulsion based on n–decanol is more efficient than the one based on n–dodecanol. The increase in the pH difference between the source and receiving phases leads to the increase in the conversion of p–nitrophenol to p–aminophenol. The efficiency of separation of the reaction product in the receiving phase is lower than the conversion at the same operating time. The apparent catalytic rate constant (kapp) of the new catalytic material based on the emulsion membrane with nanodispersion of osmium nanoparticles (0.1×10−3 for n–dodecanol and 0.9×10−3 for n-decanol) is lower by an order of magnitude compared to those based on adsorption on catalysts from platinum metal group. The advantage of the tested membrane catalytic material is that it extracts p–aminophenol in the acid receiving phase. The paper proposes a mechanism of the studied reduction system.

We study a two-echelon supply chain made up of a supplier and a manufacturer, both of which can reduce their component/product carbon emissions. With the vertical technology spillovers, we explore the optimal decisions of centralized and decentralized supply chains with price dependent demand and propose coordination strategy for the decentralized supply chain. Considering the cost contraction effectiveness of the technology spillovers, the centralized and decentralized game theoretic models of a two-echelon supply chain are developed to investigate optimal decisions of pricing and carbon emissions reduction. Through a systematic comparison and numerical analysis, we show that the profits of both players and the entire supply chain improve with the effect of technology spillovers increasing. Carbon emissions reduction will be taken by various protective measures so that the supplier and the manufacturer who do not innovate can hardly share the results of innovating via the “free-riding” methods when the technology spillover is relatively small. We also propose a revenue-cost sharing contract through bargaining to enhance the performance of the decentralized supply chain.

The uncertainty in the secondary path of an Active Noise Control (ANC) headphone affects the waterbed effect and stability of the feedback system. This study focuses on the uncertainty of the secondary path when real users wear headphones, and proposes a new uncertainty constraint based on the measured results of the secondary path transfer function under different wearing conditions of dummy head and limited subjects. This constraint and a cascaded second-order infinite impulse response filter with fixed coefficients are used to formulate a control strategic function, which is optimized by the Improved Grey Wolf Optimizer (IGWO) algorithm to obtain the optimal controller with better noise reduction performance. The proposed method and simulation model are validated based on the experimental test results. The results demonstrate that the safety factor and waterbed suppressing factor contained in the proposed uncertainty constraint ensures more stable noise reduction and effective suppression of the waterbed effect for new subjects without a priori data.

Fractal array antennas are multiband arrays having ultra wide band and space filling facility. But Side lobe levels and large number of antenna elements are the major designing challenges of these arrays. In this paper, design and analysis of octagonal fractal array antenna is investigated with Morse-Thue fractal density tapering technique (MTFDT). Due to the proposed technique, a remarkable improvement has observed in Side lobe levels and thinning of the elements can also be attained at the various iterations of octagonal fractal array antenna. These arrays are analyzed and simulated by MATLAB-15 programming.

The commercial oxygen-free copper sheets were cold-rolled with reduction rates ranging from 20% to 87% reduction rate and annealed at 400, 500 and 600 °C. The microstructure and texture evolution during cold-rolling and annealing processes were studied using optical microscopy (OM), the scanning electron microscopy (SEM) and the electron back-scattered diffraction (EBSD). The results show that the deformation textures of {123} (S) , {112} (Copper) and {110} (Brass) were continuously enhanced with the increase of cold-rolling reduction. The orientations along the α-oriented fiber converged towards Brass and the orientation density of β fiber obviously increased when the rolling reduction exceeded 60%. The recrystallization texture was significantly affected by the cold-rolling reduction. After 60% cold-rolling reduction, Copper and S textures components gradually decreased and {011} recrystallization texture component formed with the increase of annealing temperature. After 87% cold-rolling reduction, a strong Cube texture formed and other textures were inhibited with the increase of annealing temperature. The strong Brass and S deformation texture was conducive to the formation of a strong Cube annealing texture. The density of annealing twin boundary decreased with the increase of annealing temperature, and more annealing twin boundaries formed in the oxygen-free copper sheets with the increase of cold rolling reduction.

Background: Early postoperative airway management after laryngo-tracheal surgery is crucial. Acute respiratory failure due to glottis’ oedema may occur, requiring reintubation. This can prolong ventilatory assistance, jeopardizing the anastomosis. To date, only judicious steroid administration and fluid management are available to avoid more invasive procedures. High-Flow-Oxygen-Therapy(HFOT) is a noninvasive O2 support method providing humidification, warmed air, Positive-End-Expiratory-Pressure(AIRVO2). No data exist about HFOT use to prevent early complications after laryngo-tracheal surgery. Methods: Between Sept.2020-Sept.2022, 107 consecutive patients underwent laryngo-tracheal surgery received HFOT(Group A). Data and long-term results were compared with those of 80 patients operated between Sept.2018-Aug.2020(Group B), when HFOT was not available. All patients were operated in a single center. No pre- or post-operative settings changed, except for HFOT introduction. We analyzed and compared the risk for “delayed” reintubation (unexpected reintubation within the first 24-48 hours after extubating/laryngeal mask removal) in the two groups. Results: No patients reported HFOT-related adverse events. Control group(B) presented “delayed” reintubation in 37% (p= 0.027), Intensive Care Unit admission in 67%(p=0.005) and longer hospital stay(p=0.001) compared to HFOT group(A). Minor complications rate was 3% in both group and overall mortality was 0%. Re-stenosis was described in 4.6% of HFOT group, without a statistically significant difference (p=0.7006). Conclusions: Our study is the first to investigate HFOT use in patients undergoing laryngo-tracheal surgery, potentially representing a consistent innovation in the peri-operative management of these patients. With the limit of a retrospective series, we would suggest HFOT use for preventing post-operative reintubation rate, possibly reducing ICU admission and hospital stay.

Separase is a key cysteine protease to separate sister chromatids through digestion of cohesion ring that inhibits chromosome segregation as trigger of metaphase–anaphase transition in eukaryotes and highly regulated its activity by binding with securin and cyclinB-CDK1 complex. Those bindings prevent proteolytic activity of separase until the onset of anaphase. Chromosome missegregation and aneuploidy are frequently observed in malignancies. However, there are some difficulties for biochemical examinations due to instability of separase in vitro and a few spatiotemporal resolution approaches monitoring live separase activity throughout mitotic processes. Here we have developed FRET-based molecular sensors including GFP variants with separase cleavable sequences as donor and covalently attached fluorescent dye as acceptor molecules applicable to conventional live cell imaging and flow cytometric analysis because of efficient live cell uptake. We investigated performance of equivalent molecular sensors localized or not localized inside nucleus under cell cycle control using flow cytometry. Synchronized cell cycle progression rendered significant separase activity detections in both molecular sensors. We obtained consistent outcomes with localized molecular sensor introduction and cell cycle control by fluorescent microscopic observations. We thus established live cell separase activity monitoring systems specifically or statistically that could lead to elucidate separase properties in detail.

Background: Portable oxygen concentrators (POCs) have shown efficacy in delivering adequate oxygen for various patient scenarios; however, there is a lack of research on POCs’ efficacy across different respiratory rates specifically among COPD patients. Methods: This bench study was conducted using the IngMar Medical Active Servo Lung 5000 attached to flexible tubing, which simulated an adult patient’s nares. An oxygen analyzer (Maxtec Handi+) was connected to the tubing 6 inches below the nares to estimate the inspired oxygen concentration at the adult trachea. A standard nasal cannula was placed in the simulated patient nares, which was also attached to each POC. The IngMar Lung was programmed to simulate a COPD patient at the following respiratory rates: 15, 20, 30, and 40 breaths/min. POC devices were then compared to an oxygen wall outlet and a standard oxygen concentrator (non-portable CAIRE device). The POCs included the CAIRE FreeStyle Comfort (with Autosat), CAIRE FreeStyle Comfort (without Autosat), Inogen G4, Inogen G5, Phillips SimplyGo Mini, GCE Zen-O lite, Drive Medical iGo2, and Kingon POCs. Descriptive statistics and ANOVAs were computed to determine statistically significant differences between POCS and control devices (wall oxygen and standalone oxygen concentrator). Results: Across most respiratory rate scenarios, the wall oxygen and standalone oxygen concentrator (control group) resulted higher oxygen measurements compared to the POCs. Among the POCs on setting 2, the highest oxygen measurement for 15, 30, and 40 breaths/min was the CAIRE FreeStyle Comfort with AutoSat on sensitivity 5 (24.43%, 24.81%, and 25.0%, respectively). On setting 2, the 20 breaths/min highest oxygen measurement was the Inogen G4 (24.43%). For setting 5, the highest oxygen measurement for 15 breaths/min and 40 breaths/min was the CAIRE FreeStyle Comfort without AutoSat (31.56% and 26.13%, respectively), while the highest oxygen measurement for 20 breaths/min was the Inogen G5 (30.26%), and the highest oxygen measurement for 30 breaths/min was the CAIRE FreeStyle Comfort with AutoSat on sensitivity level 5 (27.89%). Conclusions: The oxygen administered through the wall and the standalone CAIRE oxygen concentrator all delivered higher oxygen levels compared to the POCs (with the exception of the 40 breaths/min scenario on setting 2). However, among the POCs, the CAIRE Freestyle Comfort with AutoSat, CAIRE Freestyle Comfort without AutoSat, and the Inogen G4 all performed the best among the various breathing rate scenarios.

Plant proteins being considered to become the most important protein source of the future, they must be able to replace the animal-derived proteins currently in use as technofunctional food ingredients. This poses challenges because plant proteins are oftentimes storage proteins with a high molecular weight and low water solubility. One promising approach to overcome these limitations is the glycation of plant proteins. The covalent bonding between the proteins and different carbohydrates created via the initial stage of the Maillard reaction can improve the technofunctional characteristics of these proteins without the involvement of potentially toxic chemicals. However, compared to studies with animal-derived proteins, glycation studies on plant proteins are currently still underrepresented in literature. This review provides an overview of the existing studies on the glycation of the major groups of plant proteins with different carbohydrates using different preparation methods. Emphasis is put on the reaction conditions used for glycation as well as the modifications to physicochemical properties and technofunctionality. Different applications of these glycated plant proteins in emulsions, foams, films, and encapsulation systems are introduced. Another focus lies on the reaction chemistry of the Maillard reaction and ways to harness it for controlled glycation and to limit the formation of undesired advanced glycation products. Finally, challenges related to the controlled glycation of plant proteins to improve their properties are discussed.

Batch and transport experiments were used to investigate the remediation of a loamy sand soil contaminated with Cr(VI) using zero valent iron nanoparticles (nZVI) stabilized by the carboxy methyl cellulose (CMC-nZVI). The effect of pH, ionic strength (IS), and flow rate on the removal efficiency of Cr(VI) were investigated under equilibrium (uniform transport) and non-equilibrium (Two-site sorption) transport using the Hydrus-1D model. The overall removal efficiency ranged from 70 to over 90% based on the chemical characteristics of the CMC-nZVI suspension and the transport conditions. The concentration and pH of the CMC-nZVI suspension had the most significant effect on the removal efficiency and transport of Cr(VI) in the soil. The average removal efficiency of Cr(VI) was increased from 24.1 to 75.5% when the concentration of CMC-nZVI nanoparticles was increased from 10 to 250 mg L-1, mainly because of the increased total surface area at larger particle concentration. Batch experiments showed that removal efficiency of Cr(VI) was much larger under acidic conditions. The average removal efficiency of Cr(VI) reached 90.1 and 60.5 % at pH 5 and 7, respectively. The Two-site sorption model described quite well (r2 = 0.96-0.98) the transport of Cr(VI) in soil as compared to the uniform transport model (r2 = 0.81-0.98). The average retardation of Cr(VI) was 3.51 and 1.61 at pH 5 and 7, respectively, indicating earlier arrival for the breakthrough curves and shorter time to reach maximum relative concentration at lower pH. The Hydrus-1D model has proven to be an efficient tool for assessing the removal of Cr(VI) pollutants, offering innovative, cost-effective, and environmentally friendly remediation methodologies.

Due to the imbalance between the supply and demand of oxygen, the oxygen system of iron- and steel-making enterprises in China has problems with high oxygen emission and high pressure in the pipelines, resulting in the energy consumption of oxygen production being high. To relieve this problem, using a large-scale iron- and steel-making mill as a case study, the research on demand forecasting and optimal scheduling of the oxygen system was carried out. The ARIMA model and the GABP model are employed to forecast oxygen demand. Based on the forecast results, an optimal scheduling model for the oxygen system was developed to conduct optimal scheduling. The case study shows that based on the oxygen demand forecast and the optimal scheduling, the oxygen emission and the pipeline pressure in the studied iron- and steel-making enterprise can be significantly reduced, thereby achieving considerable energy-saving effects and economic benefits. Specifically, the following conclusions are obtained: (1) For the oxygen demand forecast, the prediction accuracy of the GABP model is better than that of the ARIMA model. The average MAPE of the 12 sets of data of the ARIMA and GABP models are 23.8% and 20.2%, respectively. (2) By comparing the scheduling results and the field data, it is found that after the scheduling, the amount of oxygen emission has decreased by 6.32%, the pipeline pressure has decreased by 0.61%, and the energy consumption of oxygen compression has decreased by 1.6%. Considering both the oxygen emission loss and the energy consumption of oxygen compression, the total power consumption of the oxygen system is reduced by 1.38%, which saves the electricity cost of about 9.03 million RMB per year.

Noninvasive brain stimulation technique can be used for modulation of motor behaviors such as reaction time (RT). The main aim of this study was to investigate whether RT during a sequential visual isometric pinch task (SVIPT) can be affected by anodal transcranial direct current stimulation (a-tDCS) over three different stimulation sites such as dorsolateral prefrontal cortex (DLPFC), primary motor cortex (M1) or posterior parietal cortex (PPC). We also aimed to assess if stimulation of these cortical sites affect the transfer of learning during SVIPT. A total of 48 right-handed healthy participants were randomly assigned to one of the four a-tDCS groups: 1) left M1, 2) left DLPFC, 3) left PPC and 4) sham. A-tDCS was applied concurrent with SVIPT in which the participants were precisely controlled their forces to reach seven different target forces from 10 to 40% of maximum voluntary contraction (MVC) presenting on a computer screen with right dominant hand. Four test blocks were randomly performed at baseline and 15 min after the intervention including sequence and random blocks with either hand. Our results showed significant differences between a-tDCS groups on ratio RT in the sequence blocks of both the right trained (P = .041) and left untrained hands (P = .023) for target forces of 15% and 30 % of MVC, respectively. In sequence blocks, M1 showed significant elongation in ratio RT for the target force of 15% and 30 % MVC compared to PPC and Sham groups in the right hand. In sequence blocks with left hand, this negative effect were found between M1-DLPFC and M1-Sham groups. In random blocks, no significant differences were found among four groups at each target forces for the left hand while there were significant differences for 15% (P =. 04) and 40% MVC (P =. 035) in the right hand. Our findings suggest that three different stimulation sites (DLPFC, M1 or PPC) were differentially affected by a single session of a-tDCS at some target forces during SVIPT. The effects of a-tDCS on ratio RT were transferred in the left untrained hand for sequence blocks but not random blocks. Further research is needed to understand fundamental aspects of these main areas of the brain on temporal processing in a precision control task such as SVIPT.

Cutaneous mycoses are common infections whose treatment has become more complex due to increasing antifungal resistance and the need for prolonged therapies, hindering patient adher-ence and increasing the incidence of adverse effects. Consequently, the use of physical therapies, especially photodynamic therapy (PDT), has increased for the treatment of onychomycosis due to its antimicrobial capacity mediated by the production of reactive oxygen species. This study investigates the in vitro effect of the combination of blue light (448 nm) and red light (645 nm) with terbinafine on the cell viability of human keratinocytes and the production of reactive ox-ygen species. The combination of terbinafine and blue light exhibits a synergistic effect on the production of reactive oxygen species and a significant increase in the expression of superoxide dismutase (SOD), an enzyme involved in the reduction of superoxide ions (O2-) and the genera-tion of hydrogen peroxide (H2O2). Such effect could be useful in clinical practice to improve the response of cutaneous mycoses to pharmacological treatment, reduce their toxicity, and shorten their duration.

Natural cytokinins are a promising group of cytoprotective and anti-tumor agents. In this research, we synthesized a set of novel cytokinin analogs with alkyl substituents at various positions of the aromatic moiety, as well as with oxygen-containing groups, and tested their antiproliferative activity in MDA-MB-231, A-375, and U-87 MG cell lines, and cytoprotective properties in H2O2 and CoCl2 models. Two amino-linked compounds were anti-proliferative with the ability to act synergistically with doxorubicin, and two carbamate-based ones were cytoprotective. According to the molecular docking data, anti-proliferation was based on the A2AR and APRT inhibition and cytoprotection on the CDK2 inhibition. The obtained results are promising for the development of novel anti-cancer therapeutics.

Individual susceptibility to pulmonary oxygen toxicity (PO2tox) is highly variable and currently lacks a reliable biomarker for predicting pulmonary hyperoxic stress. As nitric oxide (NO) is involved in many respiratory system processes and functions, we aimed to determine if expired nitric oxide (FENO) levels can provide an indication of PO2tox susceptibility in humans. Eight U.S. Navy trained divers volunteered as subjects. The hyperoxic exposures consisted of six- and eight-hour hyperbaric chamber dives conducted on consecutive days in which subjects breathed 100% oxygen at 202.65 kPa. Subjects’ individual variability in pulmonary function and FENO was measured twice daily over five days and compared with their post-dive values to assess susceptibility to PO2tox. Only subjects who showed no decrements in pulmonary function following the six-hour exposure conducted the eight-hour dive. FENO decreased by 55% immediately following the six-hour oxygen exposure (n=8, p<0.0001) and by 63% following the eight-hour exposure (n=4, p<0.0001). Four subjects showed significant decreases in pulmonary function immediately following the six-hour exposure. These subjects had the lowest baseline FENO and the lowest post-dive FENO and had clinical symptoms of PO2tox. Individuals with low FENO were the first to develop PO2tox symptoms and deficits in pulmonary function from the hyperoxic exposures. These data suggest that endogenous levels of NO in the lung may protect against the development of PO2tox.

The cornea is an avascular tissue which has attracted much attention by the uniqueness of its anatomical characteristics, it has, in proportion, an enormous size, in relation to the number of vessels, because on average few cells in the organism are away more than 30 microns of a blood vessel. However, the cornea, with a diameter of between 11 and 12 mm, is a unique example. It has been tried to explain the notable absence of blood vessels in the cornea, arguing that corneal tissues are able to take oxygen directly from the air. In this article we are explaining that based on the physicochemical characteristics of molecular oxygen and the cell membrane, cytoplasm, water, and cellular metabolism, it is not possible that epithelial corneal cells directly take oxygen from the air, instead, corneal cells have molecules that can dissociate the water molecules thereby these cells, like any other eukaryotic cells, take the oxygen from the intracell water, like plants.

Oxidation reactions on semiconducting metal oxides (SMOs) surfaces have been extensively worked on in catalysis, fuel cells, and sensors. SMOs engaged powerfully in energy-related applications such as batteries, supercapacitors, solid oxide fuel cells (SOFCs), and chemical gas sensors. The deep understanding of SMO surface and oxygen interactions and defect engineering has become significant because all those mentioned applications are based on the adsorption/absorption and consumption/transportation of adsorbed (physisorbed-chemisorbed) oxygen. More understanding of adsorbed oxygen and oxygen vacancies (〖V_O^•,V〗_O^(••)) is needed, as the former is the vital requirement for sensing chemical reactions, while the latter facilitates the replenishment of adsorbed oxygen ions on the surface. We determined the relation between sensor response (sensitivity) and the amounts of adsorbed oxygen ions (O_(2(ads))^-,O_((ads),)^- O_2(ads)^(2-),O_((ads))^(2-)), water/hydroxide groups (H2O/OH^-), oxygen vacancies (〖V_O^•,V〗_O^(••)), and ordinary lattice oxygen ions (O_lattice^(2-)) as a function of temperature. During hydrogen (H2) testing, the different oxidation states (W6+, W5+, and W4+) of WO3 were quantified and correlated with oxygen vacancy formation (〖V_O^•,V〗_O^(••)). We used a combined application of XPS, UPS, XPEEM-LEEM, and chemical, electrical and sensory analysis for H2 sensing. We established a correlation between the H2 sensing mechanism of WO3, sensor signal magnitude, the amount of adsorbed oxygen ions, and sensor testing temperature. This paper also provides a review of the detection, quantification, and identification of different adsorbed oxygen species. The different surface and bulk-sensitive characterization techniques relevant to analyzing the SMOs-based sensor are tabulated, providing the sensor designer with the chemical, physical, and electronic information extracted from each technique.

The altered nature of archaeological metals means they deteriorate at conditions where metals would be stable. The study of deterioration for such materials is hampered by their complexity, variability and difficulties in measuring deterioration. Placing an object in a sealed container, controlling the RH and pollutant gases and measuring any decrease in oxygen concentration is an accessible method to measure deterioration rate. It has been used for research into suitable environmental conditions to manage deterioration rates of such artefacts including differences in response for artefacts from different excavation sites. Some objects need careful control of RH to low values, this is expensive to maintain and poses risks to other artefacts displayed together. Many objects are actually stable up to quite high RH values and oxygen depletion testing has been used to identify those that can be safely displayed with minimal environmental control. The accelerated corrosion, ‘Oddy’ test is frequently used to sift out unsuitable display materials. The visual assessment is widely recognized to be subjective. The test container has been modified and oxygen depletion appears to give good quantitative measurements of corrosion that correspond with both visual comparison and corrosion quantification for copper, lead and steel, but not for silver.

As the world’s population age, Cognitive Frailty (CF) is becoming one of the most serious health problems and elucidating its biological mechanisms along with prevention and treatments becomes increasingly important also considering the associated health costs. This pilot study aims to investigate the potential cognitive and neuropsychological effects of a 5-week treatment with a therapy based on the regenerative properties of ozone (O3) in a cohort of patients stratified according to CF. We also study the potential effects of O3 on blood-based biomarkers indicative of specific biological systems that may be altered in CF. Seventy-five older persons have been recruited and randomly assigned to receive the active treatment (150cc of oxygen-O2-O3 mixture at the concentration of 30ug of O3 per cc of O2) or O2, or the placebo (air) for 5 weeks. The primary endpoint is a change in the scores of clinical scales from baseline (T0) to weeks 3 (T3), 9 (T9), 15 (T15) after treatment. The secondary endpoint is a change in biomarkers levels resulting from transcriptomics, proteomics and metabolomic patterns at the same times. This study will evaluate whether an intervention with the O2-O3 therapy could have potential cognitive, neuropsychological and biological effects on CF.

Saprotrophic fungi are key in global carbon cycling, capable of decomposing lignocellulose in wood. This study, for the first time, explores the influence of oxygen (O2) and temperature on methane (CH4) production by two fungi, Laetiporus sulphureus and Pleurotus sapidus. We examined CH4 formation under varying O2 levels (0 to 98%) and temperatures (17, 27, and 40 °C) when the fungi grew on pine wood, beech wood, and grass under sterile conditions. Our findings reveal a strong dependency of fungal CH4 production on O2 mixing ratios. Methane formation was highest when O2 levels exceeded 5%, whilst no CH4 formation was observed after complete O2 consumption by the fungi. Reintroducing O2 immediately resumed fungal CH4 production. When CH4 formation was normalized to O2 consumption (CH4_norm) a different pattern between species was observed. L. sulphureus showed higher CH4_norm rates with higher O2 levels, whereas P. sapidus showed elevated rates between 0-5% O2. Temperature also significantly influenced CH4 and CH4_norm rates, with the highest production at 27 °C, and comparatively lower rates at 17 and 40 °C. These results demonstrate that O2 levels and temperature are critical in controlling fungal CH4 emissions, a consideration necessary for future CH4 source predictions.

Replacing carbon by hydrogen is a huge step towards reducing CO₂ emissions in the iron- and steel-making industry. The reduction of iron oxides using hydrogen plasma smelting reduction as an alternative to conventional steel-making routes has been studied at Montanuniversitaet Leoben, Austria. The aim of this work was to study the slag formation during the reduction process and the reduction behaviour of iron oxides. Furthermore, the reduction behaviour of iron ore during continuous feeding was assessed. Mixtures of iron ore and calcined lime with a basicity of 0, 0.8, 1.6, 2.3, and 2.9 were melted and reduced by hydrogen. The off-gas composition was measured during the operations to calculate the process parameters. The reduction parameters, namely the degree of reduction, degree of hydrogen utilisation, produced iron, and slag, are presented. The results of the batch-charged experiments showed that at the beginning of the reduction process, the degree of hydrogen utilisation was high, and then, it decreased over the operation time. In contrast, during the continuous-feeding experiment, the degree of hydrogen utilisation could be kept approximately constant. The highest degrees of reduction and hydrogen utilisation were obtained upon the application of a slag with a basicity of 2.3. The experiment showed that upon the continuous feeding of iron ore, the best conditions for the reduction process using hydrogen could be applied.

Establishment of diagnostic methods with low detection limits plays a critical role in the maintenance of early diagnosis, prevention of serious neurological complications, and control of the spread of ZIKA. In this study, we established the micro-droplet digital polymerase chain reaction (ddPCR) and real-time fluorescent quantification PCR (qPCR) protocols for the detection of Zika virus based on the NS5 gene. For the Zika standard plasmid, the standard curve of R² was 0.999, and the amplification efficiency was 92.203%, as determined by qPCR. Both ddPCR and qPCR were positive for cell culture of Zika nucleic acid.The minimum detection limit of ddPCR is 1–2 times lower than qPCR. Moreover, all tests of Dengue virus (1–4 serotypes) were negative in cell culture. Overall, these results suggested than ddPCR may have a lower limit of detection than qPCR.

Luminescence-based sensors for measuring oxygen concentration are widely used both in industry and research due to the practical advantages and sensitivity of this type of sensing. The measuring principle is the luminescence quenching by oxygen molecules, which results in a change of the luminescence decay time and intensity. In the standard approach, this change is related to an oxygen concentration using the Stern–Volmer equation. This equation, which in most of the cases is non-linear, is parametrized through device-specific constants. Therefore, to determine these parameters every sensor needs to be precisely calibrated at one or more known concentrations. This work explores an entirely new artificial intelligence approach and demonstrates the feasibility of oxygen sensing through machine learning. The specifically developed neural network learns very efficiently to relate the input quantities to the oxygen concentration. The results show a mean deviation of the predicted from the measured concentration of 0.5 % air, comparable to many commercial and low-cost sensors. Since the network was trained using synthetically generated data, the accuracy of the model predictions is limited by the ability of the generated data to describe the measured data, opening up future possibilities for significant improvement by using a large number of experimental measurements for training. The approach described in this work demonstrates the applicability of artificial intelligence to sensing technology and paves the road for the next generation of sensors.

A sustainable green one pot procedure for the synthesis of dihydropyrimidinones (DHPMs) derivatives by a three-component reaction of β-ketoester derivatives, aldehyde and urea or thiourea over the alkali-treated H-ZSM-5 zeolite under ball-milling has been developed. The product was isolated by simple washing of the crude reaction residue with ethyl acetate followed by evaporation of solvent. The hierachical zeolite catalyst (MFI27_6) showed high yield (86–96%) of dihydropyrimidinones (DHPMs), in very short time (10-30 min). The catalyst is recycled for subsequent reactions in four runs without appreciable loss of activity and high yields of products provide efficient protocol for Biginelli reactions.

Oxygen extraction fraction (OEF), the fraction of oxygen that tissue extracts from blood, is an es-sential biomarker for directly assessing tissue viability and function in neurologic disorders. For quantitative mapping of OEF, an integrative model of quantitative susceptibility mapping and quantitative blood oxygen level-dependent magnitude (QSM+qBOLD or QQ) was recently pro-posed. However, QQ assumes Gaussian noise in both susceptibility and multi-echo gradient echo (mGRE) magnitude signals for OEF estimation. This assumption is unreliable in low sig-nal-to-noise ratio (SNR) regions like disease-related lesions, risking inaccurate OEF estimation and potentially impacting clinical decisions. Addressing this, our study presents a novel multi-echo complex QQ (mcQQ) that models realistic noise in mGRE complex signals. The proposed mcQQ was implemented using a deep learning framework (mcQQ-NET) and compared with the existing deep learning-based QQ (QQ-NET) in simulations, ischemic stroke patients, and healthy subjects. Both mcQQ-NET and QQ-NET used identical training and testing datasets and schemes for a fair comparison. In simulations, mcQQ-NET provided more accurate OEF than QQ-NET. In the sub-acute stroke patients, mcQQ-NET showed a lower average OEF ratio in lesions relative to unaf-fected contralateral normal tissue than QQ-NET. In the healthy subjects, mcQQ-NET provided uniform OEF maps, similar to QQ-NET, but without unrealistically high OEF outliers in areas of low SNR. Therefore, mcQQ-NET improves OEF accuracy by better reflecting realistic data noise characteristics.

Catalyst material plays a pivotal role in the pharmaceutical industry process. Among them, Friedel-Craft acylation reaction is a well-known reaction to synthesis acetophenone derivatives. However, Friedel-Craft acylation mostly used acetyl chloride as starting material with Lewis acid as homogeneous catalyst, which is nonenvironmental friendly process. In this work, a simple and efficient Friedel-Craft acylation reaction is reported by using the palladium oxide doped on activated bentonite (PdOAB) as the heterogeneous catalyst. The PdOAB catalyst material was characterized with scanning electron microscopy-energy dispersive X-ray (SEM-EDX), nitrogen isotherm adsorption, Fourier transform infrared (FTIR), X-ray powder diffraction (XRD), and thermogravimetric-differential thermal analysis (TG-DTA). The acetophenone derivatives with R = -H, -Cl, -CH₃, -OCH₃, -OH and -NH₂ at para position were successfully synthesized from its corresponding aromatic compounds with glacial acetic acid in 86.6, 7.9, 91.7, 86.6, 82.7, and 78.9% yield, respectively. Therefore, a green method was established because the byproduct is water and the catalyst material can be recovered. Furthermore, the substituent (σ) constants were obtained by using Hammet equation, and the catalysis mechanism has been proposed.

Developing sustainable and renewable energy sources is critical as higher and higher global energy and environmental challenges arise. Hydrogen has the highest mass/energy density of any fuel and is considered one of the best sources of clean energy. Water splitting is regarded as one of the most promising solutions for hydrogen production on a large scale. Highly efficient, durable and cost-effective catalysts for hydrogen evolution reaction (HER) are critical in the realization of this goal. Among many materials proposed, graphene-based materials offer some unique properties for HER catalysis. In this review, we present recent progress on development of graphene-based electrocatalysts toward HER throughout the past few years.

This work demonstrates that a plasmid can function as an efficient biocatalyst in mediating the nitroaldol (Henry) reaction at high temperatures in ultrapure water. Compared with ssDNA, the plasmid displayed a remarkable catalytic efficiency (97% yield within 20 min). Aromatic aldehydes which bear strong or moderate electron-withdrawing groups reacted satisfactorily with nitromethane, which afforded the corresponding β-nitroalcohols in good yields within 2 h (up to 98%). By contrast, aliphatic and aromatic aldehydes with electron-donating groups did not react. Moreover, the yield significantly dropped when the size of the carbanion increased, and the yield was only 10% when nitropropane was used as the donor.

membrane separation technology shows promise, particularly gas separation membranes, including ceramic membrane. Ceramic membranes are increasingly gaining attention for their acid and alkali stability, corrosion resistance, high-temperature tolerance, and mechanical strength. This study focuses on alumina support ceramic membrane for CO2 capture. The membranes were characterized using contact angle measurements, scanning electron microscopy (SEM), and Fourier Transform Infrared spectroscopy (FTIR) analysis. The contact angle measurements confirmed the hydrophilic, while SEM analysis showed even particle distribution in the alumina ceramic membranes respectively. EDAX analysis revealed the elemental composition in the alumina support matrix. FTIR analysis demonstrated chemical interactions of the support membrane. Single gas permeation experiments were conducted. It can be observed that Nitrogen gas permeated faster with increase in feed pressure through the unmodified ceramic inorganic hydrophobic membrane more than the other two single gases, O2, and CO2). As a result, only high permeance separation membranes with realistic size and pressure conditions may be considered of as a practical alternative for CO2 capture. However, the presence of non-selective defects limited the improvement in selectivity of hydrophilic ceramic membrane. In this case, there is need to modify the ceramic membrane used to increase the flux, permeance of CO2, and selectivity of CO2.

Abstract: membrane separation technology shows promise, particularly gas separation membranes, including ceramic membrane. Ceramic membranes are increasingly gaining attention for their acid and alkali stability, corrosion resistance, high-temperature tolerance, and mechanical strength. This study focuses on alumina support ceramic membrane for CO2 capture. The membranes were characterized using contact angle measurements, scanning electron microscopy (SEM), and Fourier Transform Infrared spectroscopy (FTIR) analysis. The contact angle measurements confirmed the hydrophilic, while SEM analysis showed even particle distribution in the alumina ceramic membranes respectively. EDAX analysis revealed the elemental composition in the alumina support matrix. FTIR analysis demonstrated chemical interactions of the support membrane. Single gas permeation experiments were conducted. It can be observed that Nitrogen gas permeated faster with increase in feed pressure through the unmodified ceramic inorganic membrane more than the other two single gases, O2, and CO2). As a result, only high permeance separation membranes with realistic size and pressure conditions may be considered of as a practical alternative for CO2 capture. However, the presence of non-selective defects limited the improvement in selectivity of hydrophilic ceramic membrane. In this case, there is need to modify the ceramic membrane used to increase the flux, permeance of CO2, and selectivity of CO2.

It is unclear whether military shoes (combat boots and sports shoes) attenuate loading rate or affect force transfer during walking. Therefore, this study compared ground reaction forces (GRF) related to impact and force transfer between combat boots, military sports shoes and running shoes. Ten army recruits walked over a walkway with two force plates embedded. GRF were measured when walking barefoot (for data normalization) and with combat boots, military sports shoes and running shoes. Loading rate, first and second peak forces and push-off rate of force were computed along with temporal analysis of waveforms. Reduced loading rate was observed for the running shoe compared to the combat boot (p = 0.02 and d = 0.98) and to the military sports shoe (p = 0.04 and d = 0.92). The running shoe elicited a smaller second peak force than the combat boot (p < 0.01 and d = 0.83). Walking with military shoes and combat boots led to larger force transfer then running shoes potentially due to harder material used in midsole composition (i.e. styrene-butadiene rubber). These results could lead to a potentially larger risk of injuries while long duration walking in military shoes and boots compared to traditional running shoes.

Bare titania and metal promoted TiO2 catalysts were employed in the treatment of nitrates, which are ubiquitous pollutants of wastewater. The results show that the process can be carried out under visible light (from white light LED lamp) and, in the best case, 23.5% conversion of nitrate was obtained over 4 hours with full selectivity towards N2 by employing 0.1 mol% Ag/TiO2 prepared by flame spray pyrolysis. Moreover, the performance was worse when testing the same catalysts with tap water (11.3% conversion), due to the more complex composition of the matrix. At last, it was found that the photoreduction of nitrate can be effectively performed in combina-tion with the photo-oxidation of ammonium without loss in the activity, opening to the possi-bility to treat highly polluted wastewater with a single process. The latter treatment employs the two contaminants simultaneously as electron and holes scavengers, with very good selectiv-ity, in a completely new process that we may call Photo-Selective Catalytic Reduction (Pho-to-SCR).

Ethanolic extracts of propolis collected from Apis mellifera hives have been shown to reduce Nosema ceranae infection in honey bee workers. This study aimed to determine the propolis concentration that optimizes the control of N. ceranae infection in honey bee workers. Newly emerged worker bees were individually fed 2 μL of 50% sucrose solution (w/v) containing 105 N. ceranae spores per bee, and treated with 0%, 25%, 50%, and 75% ethanolic extracted propolis in 50% sucrose solution (v/v). The treated bees were maintained in cages at 34 ± 2˚C and 55 ± 5% RH throughout the study. The number of dead bees was counted and removed from the cages daily for 30 days to generate survival curves. The number of N. ceranae spores per bee (infectivity) was quantified using a hemocytometer, and the number of infected bees per hundred bees (infection rate) was determined. The survival rates of N. ceranae infected bees fed 25%, 50%, and 75% propolis (NP1, NP2, NP3, respectively) were significantly higher than those of infected bees not fed propolis (NO). Furthermore, the infectivity and infection rates of NP2 and NP3 groups were significantly lower than those of the NO group. The infectivity and infection rates of the NP1 group were not different than those of the NO group. Our data suggest that 50% and 75% propolis extracts are appropriate concentrations for treating N. ceranae infection in honey bees. Ethanolic extracted propolis can be an alternative treatment for N. ceranae infection in Western honey bees.

Iron-based materials are widely applied in Fenton chemistry and they have promising prospects in the processing of wastewater. The composition complexity and rich chemistry of iron and/or oxides, however, hamper the precise understanding on the active sites and the working mechanism which still remain highly controversial. Herein, iron oxides of four different model systems are designed through a conventional precipitation method plus H2 reduction treatment. These systems feature Fe@Fe3O4 with abundant oxygen vacancy, Fe0 and Fe3O4 particles with interface structures, and Fe3O4-dominated nanoparticles of different sizes. These materials are applied in the decomposition of methyl orange as a model reaction to assess the Fenton chemistry. The Fe@Fe3O4 with core-shell structures exhibited significantly higher decomposition activity than the other Fe3O4-rich nanoparticles. A thin Fe3O4 layer formed by auto-oxidation of iron particles when exposing to air can boost the activity as compared with the Fe0 and Fe3O4 particles with interface structures but poor oxygen vacancy. The unique hetero-structure with the co-existence of both metallic iron and oxygen vacancy displayed excellent redox propensity which might account for the superior Fenton activity. This finding provides a new perspective to understand and design highly efficient iron-based Fenton catalysts.

Telomere repeats at the ends of human chromosomes protect chromosomes from degradation, and telomerase has a prominent role in telomere maintenance. Telomerase also affects cell proliferation, DNA replication, differentiation, and tumourigenesis. TERT (telomerase reverse transcriptase enzyme) is the catalytic subunit of telomerase and is critical for enzyme activity. TERT promoter mutations and promoter methylation are strongly associated with increased telomerase activation in cancer cells. Notably, TERT and telomerase are downregulated in stem cells during their differentiation. Therefore, the link between differentiation and telomerase provides a valuable tool for studying the epigenetic regulation of TERT enzyme. Oxygen tension affects several cellular behaviours including proliferation, metabolic activity, stemness, and differentiation. The role of oxygen tension in driving promoter modifications of the TERT gene in embryonic stem cells (ESCs) is poorly understood either in vitro or in vivo. We adopted a monolayer ESCs differentiation model to explore the role of low, physiological, oxygen (physoxia) in the epigenetic regulation of telomerase and associated genes, including TERT, DNMTs, and HDACs. Cells were cultured in either air, a 2% O2 incubator, or a 2% O2 oxygen workstation to provide a fully defined 2% O2 environment. Pre-gassed media (pre-conditioned to 2% O2 in a HypoxyCool unit) was used in all 2% O2 experimentation. As anticipated, physoxia culture increased the proliferation rate and stemness of ESCs and a slower onset of differentiation in physoxia was evident. Further, downregulated TERT expression was correlated to reduced telomerase activity during differentiation. TERT expression and telomerase activity remained significantly elevated in physoxia during differentiation. A substantial increase in TERT promoter methylation levels was noted during differentiation. Chemical inhibition of DNMT3B reduced TERT promoter methylation and was associated with increased TERT gene and telomerase activity during differentiation. DNMT3B CHiP demonstrated that downregulated TERT expression and increased proximal promoter methylation were associated with DNMT3B binding to the promoter. In conclusion, we have demonstrated that DNMT3B can directly bind TERT promoter, change its methylation levels, and contribute to regulation of telomerase activity.

: Oscillation synchronization through diffusion-based communication of active materials can lead to emergence of diverse patterns and collective behaviors. A detailed general description of the formation process of synchronization or resynchronization dynamics is a challenging task. We employ a photosensitive Belousov-Zhabotinsky reaction-diffusion model (within a gel media) to investigate the recovery process of oscillation synchronization between a pair of gel patches. The recovery time for oscillation resynchronization can be modulated by patch-distance, species of signaling molecules, intensity and duration of illumination. Analysis reveals that the “switch effect” of the gel-distance and the “promotion effect” from illumination on the oscillation resynchronization originate from the competition between processes of photo-promotion of oscillation, diffusion of signaling molecules (HBrO2 and Br-) and disproportionation of HBrO2. These results will benefit studies on bio-inspired active materials and soft motors.

The increase in carbon dioxide emissions has a significant impact on human society and the global environment. As the most abundant and cheap C1 resource, the conversion and utilization of carbon dioxide has received extensive attention from researchers. In many methods of carbon dioxide conversion and utilization, the reverse water gas conversion reaction is considered to be one of the most effective ways. In this paper, the research progress of reverse water gas conversion reaction in recent years is introduced.

MoS2 has long been considered as a promising catalyst for hydrogen production. At present, there are many strategies to further improve its catalytic performance, such as edge engineering, defect engineering, phase engineering and so on. However, at present, there is still a great deal of controversy about the mechanism of MoS2 catalytic hydrogen production. For example, it is generally believed that the base plane of MoS2 is inert, but it has been reported that the inert base plane can undergo a transient phase transition in the catalytic process to play the catalytic role, which is contrary to the common understanding that the catalytic activity is only at the edge. Therefore, it is necessary to further understand the mechanism of MoS2 catalytic hydrogen production. In this article, we summarized the latest research progress on the catalytic hydrogen production of MoS2, which is of great significance for revisited the mechanism of MoS2 catalytic hydrogen production.

Dynamics of human populations can be affected by various socio-economic factors through their influence on the natality and mortality rates, and on the migration intensity and directions. In this work we study an economic-demographic model which takes into account the dependence of the wealth production rate on the available resources. In the case of nonlocal consumption of resources the homogeneous in space wealth-population distribution is replaced by a periodic in space distribution for which the total wealth increases. For the global consumption of resources, if the wealth redistribution is small enough, then the homogeneous distribution is replaced by a heterogeneous one with a single wealth accumulation center. Thus, economic and demographic characteristics of nonlocal and global economies can be quite different in comparison with the local economy.

Temperature influences the life of many organisms in various ways. A great number of them live under conditions, where their ability to adapt to changes in temperature can be vital and largely determine their fitness. Understanding the mechanisms and principles underlying this ability to adapt can be of great advantage, for example, to improve growth conditions for crops and increase their yield. In times of imminent, increasing climate change, this becomes even more important, in order to find strategies and help crops cope with these fundamental changes. There is intense research in the field of acclimation, that comprises fluctuations of various environmental conditions, but most acclimation research focuses on regulatory effects and the observation of gene expression changes within the examined organism. As thermodynamic effects are a direct consequence of temperature changes, these should necessarily be considered in this field of research, but are often neglected. Also, compensated effects might be missed, even though they are equally important for the organism, since they do not cause observable changes, but rather counteract them. In this work, using a systems biology approach, we demonstrate that even simple network motifs can exhibit temperature dependent functional features, resulting from the interplay of network structure and the distribution of activation energies over the involved reactions. The demonstrated functional features are (i) the reversal of fluxes within a linear pathway, (ii) a thermo-selective branched pathway with different flux modes and (iii) the increased flux towards carbohydrates in a minimal calvin cycle that was designed to demonstrate temperature compensation within reaction networks. By this, we expand the scope of thermodynamic modelling of biochemical processes by addressing further possibilities and effects, following established mathematical descriptions of biophysical properties.

The tsscds method, recently developed in our group, discovers chemical reaction mechanisms with minimal human intervention. It employs accelerated molecular dynamics, spectral graph theory, statistical rate theory and stochastic simulations to uncover chemical reaction paths and to solve the kinetics at the experimental conditions. In the present review, its application to solve mechanistic/kinetics problems in different research areas will be presented. Examples will be given of reactions involved in photodissociation dynamics, mass spectrometry, combustion chemistry and organometallic catalysis. Some planned improvements will also be described.

Photodynamic therapy (PDT) has garnered significant attention in the fields of cancer treatment and drug-resistant bacteria eradication due to its non-invasive nature and spatiotemporal controllability. Iridium complexes have captivated researchers owing to their tunable structure, exceptional optical properties, and substantial Stokes displacement. However, most of these complexes suffer from aggregation-induced quenching, leading to diminished luminous efficiency. In contrast to conventional photosensitizers, photosensitizers exhibiting aggregation-induced luminescence (AIE) properties retain the ability to generate a large number of reactive oxygen species when aggregated. To overcome these limitations, we designed and synthesized a novel iridium complex named Ir-TPA in this study. It incorporates quinoline triphenylamine cyclomethylated ligands that confer AIE characteristics for Ir-TPA. We systematically investigated the photophysical properties, AIE behavior, spectral features, and reactive oxygen generation capacity of Ir-TPA. The results demonstrate that Ir-TPA exhibits excellent optical properties with pronounced AIE phenomenon and robust capability for producing singlet oxygen species. This work not only introduces a new class of metal iridium complex photosensitizer with AIE attributes but also holds promise for achieving remarkable photodynamic therapeutic effects in future cellular experiments and biological studies.

The kidney and the heart work together in balancing the body circulation and although their physiology is based on strict inter dependence, their performance fulfills different aims. While the heart can rapidly increase its own oxygen consumption to comply with the wide changes in metabolic demand linked to body function, the kidney physiology is primarily designed to maintain a stable metabolic rate and has limited capacity to cope with any steep increase in renal metabolism. In the kidneys the glomerular population filters a large amount of blood and the tubular system has been programmed to reabsorb 99% of filtrate by reabsorbing sodium together with other filtered substances including all glucose molecules. Glucose reabsorption involves the sodium-glucose cotransporters SGLT2 and SGLT1 on the apical membrane in the proximal tubular section; it also enhances bicarbonate formation so as to preserve the acid-base balance. The complex work of reabsorption in the kidney is the main factor in renal oxygen consumption; analysis of renal glucose transport in disease states is providing better understanding of the renal physiology changes that occur when clinical conditions alter the neurohormonal response leading to an increase in glomerular filtration pressure. In this circumstance glomerular hyperfiltration occurs, imposing a higher metabolic demand on kidney physiology and causing progressive renal impairment. Albumin urination is the warning signal of renal engagement over-exertion and most frequently heralds heart failure development, regardless of disease etiology. The review analyzes the mechanisms linked to renal oxygen consumption, focusing on sodium-glucose management.

Scientific theories on the functioning and dysfunction of the human brain require a good understanding of both its development — before and after birth, and through maturation to adulthood — and its evolution from the ancestral primate brain. Adopting a complex-systems approach, here we propose that the apparent uniqueness of humans’ cognitive capacities might best be understood as emerging from multiple nested “virtuous cycles.” In particular, we propose that the intimate link that exists between oxygen metabolic loops, cortical expansion, and ultimately cognitive and social demands is a key driver of genetic developmental programs for the human brain. Overall, our proposed evolutionary model makes explicit mechanistic links between metabolism, molecular and cellular brain heterogeneity, and behaviour that may in time provide a clearer understanding of brain developmental trajectories and their disorders.

The data from social networks like Twitter is a valuable source for research but full of redundancy, making it hard to provide large-scale, self-contained, and small datasets. The data recording is a common problem in social media-based studies and could be standardized. Sadly, this is hardly done. This paper reports on lessons learned from a long-term evaluation study recording the complete public sample of the German and English Twitter stream. It presents a recording solution proposal that merely chunks a linear stream of events to reduce redundancy. If events are observed multiple times within the time-span of a chunk, only the latest observation is written to the chunk. A 10 Gigabyte Twitter raw dataset covering 1,2 Million Tweets of 120.000 users recorded between June and September 2017 was used to analyze expectable compression rates. It turned out that resulting datasets need only between 10\% and 20\% of the original data size without losing any event, metadata or the relationships between single events. This kind of redundancy reduction recording makes it possible to curate large-scale (even nation-wide), self-contained, and small datasets of social networks for research in a standardized and reproducible manner.

In this paper, the computational fluid dynamics (CFD) method has been used to simulate the gas flow and the catalytic hydrogenation process of the C-2 hydrogenation adiabatic reactor in a practical ethylene production unit of a chemical plant. The laminar finite-rate model was used for the chemical reaction model. The standard two-equation model was used for the turbulence model. The exponent-function kinetic model was used for the reaction dynamics model. The simulation results were in good agreement with the actual industrial data obtained from the C-2 hydrogenation reactor, and the distributions of reaction parameters such as temperature and component concentrations in the reactor were further analyzed. Based on the validated CFD models, the structure and operating conditions of the reactor, as well as hydrogen load distribution ratios, are simulated for comparing the comprehensive performance metrics of ethylene selectivity and acetylene conversion rate; as a result, we can obtain the optimal temperature of 312 K, the optimal hydrogen/acetylene ratio of 0.10 as well as the optimal hydrogen load distribution ratio of 4:4:2, and the diameter/height ratio exerts a marginal effect on the selectivity, conversion rate and harmonic mean of the reactor.

A systematic study has been conducted on barbiturate complexes of all five alkali metals Li–Cs prepared from the metal carbonates or hydroxide in aqueous solution without other potential ligands present, varying the stoichiometric ratio of metal ion to barbituric acid (BAH). Eight polymeric compounds (two each for Na, K, and Rb and one each for Li and Cs) have been characterised by single-crystal X-ray diffraction. All contain some combination of barbiturate anion BA− (necessarily in a 1:1 ratio with the metal cation M+), barbituric acid, and water. All organic species and water molecules are coordinated to the metal centres via oxygen atoms as either terminal or bridging ligands. Coordination numbers range from 4 (for the Li complex) to 8 (for the Cs complex). Extensive hydrogen bonding plays a significant role in all the crystal structures, almost all of which include pairs of N–H…O hydrogen bonds linking BA− and/or BAH components into ribbons extending in one dimension. Factors influencing the structure adopted by each compound include cation size and reaction stoichiometry as well as hydrogen bonding.

Heterocycles are unique precursors for the synthesis of various pharmaceuticals and agrochemicals particularly those possessing N- or O- moieties. The development of methods to prepare heterocycles is of great importance in synthesis of organic compounds, especially the heterocycles which can be found in natural products. The synthesis of nitrogen and oxygen containing heterocycles viz. coumarins, dihydropyrimidinones, imidazoles, isoxazoles and benzimidazoles represented an attractive and demanding work for chemists as these nucleus has found extensive applications in several fields such as material science, analytical chemistry and most importantly in medicinal chemistry. Organic synthesis has been attracted towards the development of new environmental friendly procedures to achieve the goals of green chemistry. The fundamental aspects of green chemistry are use of biocatalysts and environmental benign solvents under mild conditions. The present review article summarized the green synthetic methods and biological activities of nitrogen and oxygen containing heterocycles.

We report on the phosphorescence of singlet oxygen photogenerated through a stimulated Raman process. Nanosecond radiation in the green spectral region focused on hexane induces a Raman transition of the dissolved in the solvent oxygen molecules toward the singlet oxygen state producing a Stokes signal in the near infrared. The excited oxygen relaxes to ground emitting an infrared photon at 1269 nm. While the Stokes signal’s wavelength changes with the pumping light’s wavelength, the wavelength of the phosphorescent photon remains unaltered. The result confirms previously reports on stimulated Raman excitation of singlet oxygen.

Addressing global environmental problem, water splitting to produce hydrogen fuel by solar energy is getting so much attention. In the water splitting, the essential problem to solve is the development of efficient　catalysts for oxygen production. In this paper, having the prospect for a practical application of photocatalysts to artificial photosynthesis, molecular mechanisms in the current literature are briefly reviewed. At first, recent progress in the function of Mn cluster at the natural photosystem II is briefly described. The kinds of devices in which oxygen evolution reaction (OER) catalysts are used were designated; water electrolyzers, photoelectrodes, and photocatalysts. Some methods for analyzing molecular mechanism in OER catalysis, emphasized by FTIR method, are shown briefly. After describing common OER mechanisms, the molecular mechanisms are discussed for TiO2 and BiVO4 photoelectrodes with our novel data, followed by presenting of co-catalysts IrO2, RuO2, NiO2, and other metal oxides for OER catalysts. Recent reports describing OER catalysts of perovskites, layered double hydroxides (LDH), metal-organic frameworks (MOF), single atom catalysts, as well as metal complexes are reviewed. Finally, by comparing with natural photosystem, the requiring factors to improve the activity of the catalysts for artificial photosynthesis will be discussed.

Oxygen based heterocyclic moieties hold an ample range of therapeutic activities. Heterocyclic molecules are nominated as vital components of an extensive array of structural motifs with both biological and pharmaceutical significance. The oxygen-based scaffolds act as anticancer candidates and are also present in numerous phytomolecules viz; irinotecan, camptothecin, topotecan, taxol, taxotere, podophylotoxin, etoposide, daunorubicin and teniposide. The architectural design of numerous structural motifs for amelioration of cancer has become progressively amplified in recent past years. Until now presently there is no strategic treatment which is so capable that can cure cancer from its roots. Henceforth, it is very indispensible to design novel anticancer structural motifs with least side effects. The oxygen containing heterocyclic scaffolds includes flavonoids, pyrans, xanthones and coumarins are of utmost importance in medical chemistry for the mitigation of cancer. This assemblage offers several recent developments as anticancer oxygen containing heterocyclic molecules all-round the globe and attracted the structural motifs of auspicious molecules, along with their mechanistic insights, IC50 values, structure–activity relationships, and molecular docking studies. The encouraging properties discovered by these oxygen-based scaffolds unconditionally engaging them at frontline in invention of potential drug candidates. Consequently, these probably will be of amazing attention to scientists working on the design and synthesis of antitumor candidates.

The surface fluorination of polypropylene (PP) was performed using F2 and O2 gas mixtures with different F2 gas proportions at 25 °C and 13.3 kPa for 1 h. The surface roughness of the fluorinated PP samples was approximately 1.5 times higher than that of the untreated sample (5 nm). The Fourier-transform infrared spectroscopy (FTIR) and X-ray photoelectron spectroscopy (XPS) results showed that the PP-derived bonds (-C-C- and -CHx) decreased because they were converted into polar groups (-C–O, -CHF-, and -CFx), which increased the surface electronegativity of PP. The variation in the F2 gas proportion in the gas mixture significantly affected the hydrophilicity and surface composition of PP. At F2 gas proportions of <70%, the hydrophilicity of the fluorinated PP samples improved. Notably, the hydrophilic and negatively charged PP surface enhanced the dyeing of the polymer with basic methylene blue (MB). In contrast, at F2 gas proportions of >90%, the PP surface became hydrophobic owing to increased hydrophobic -CF3 bonds. Thus, enhanced PP dyeing can be controlled based on the composition of the F2 and O2 gas mixture.

Worldwide, oral lesions and cancers are still being significant public health conditions. Thus, an introduction of new oral healthcare protocols is becoming essential. Oral diseases are related to many causative factors, manly dental plaque/biofilm due to poor hygiene. New anti-biofilm therapies are needed to develop. The strategies of anti-biofilm therapies should help to control biofilm formation and microbial attachment to dental surfaces. The present review aimed to provide a comprehensive over-view on evidence related to the potential utility of topical oxygen therapy (BlueM formula) as novel oral care therapies in clinical practice.

Photoacoustic imaging is attracting a great deal of interest owing to its distinct advantages over other imaging techniques such as fluorescence or magnetic resonance image. Availability of photoacoustic probes for reactive oxygen and nitrogen species (ROS/RNS) could shed light on a plethora of biological processes mediated by these key intermediates. Tetramethylbenzidine (TMB) is a non-toxic and non-mutagenic colorless dye that develops a distinctive blue color upon oxidation. In this work we have investigated the potential of TMB as photoacoustic probe for ROS/RNS. Our results indicate that TMB reacts with hypochlorite, hydrogen peroxide, singlet oxygen and nitrogen dioxide to produce the blue oxidation product, while ROS such as the superoxide radical anion, sodium peroxide, hydroxyl radical or peroxynitrite yield a colorless oxidation product. TMB does not penetrate Escherichia coli cytoplasm but is capable of detecting singlet oxygen generated in its outer membrane.

Dissolved Oxygen (DO) concentration is a vital parameter that indicates water quality. DO short term forecasting using time series analysis on data collected from an aquaculture pond is presented here. This can provide data support for an early warning system for an improved management of the aquaculture farm. The conventional forecasting approaches are commonly characterized by low accuracy and poor generalization problems. In this article, we present a novel hybrid DO concentration forecasting method with ensemble empirical mode decomposition (EEMD) based LSTM (Long short-term memory) neural network (NN). With this method, first, the sensor data integrity is improved through linear interpolation and moving average filtering methods of data preprocessing. Next, the EEMD algorithm is applied to decompose the original sensor data into multiple intrinsic mode functions (IMFs). Finally, the feature selection is used to carefully select IMFs that are strongly correlated with the original sensor data and integrate both into inputs for the NN. The hybrid EEMD-based LSTM forecasting model is then constructed. Performance of this proposed model in training and validation sets was compared with the observed real sensor data. To obtain the exact evaluation accuracy of the forecasted results of the hybrid EEMD-based LSTM forecasting model, three statistical performance indices were adopted: MAE, MSE, and RMSE. Results presented for short term (12-hour period) and long term (1-month period) give a strong indication of suitability of this method for forecasting DO values.

Cellular oxidation is responsive to external and internal stimulation and is generated via signal molecules in defense mechanisms through networks of cell proliferation, differentiation, intracellular detoxification, bacterial infection, and immune reactions. Oxidative stress is not necessarily harmful per se; it depends on the balance between oxidation and antioxidation cascades, which are induced according to stimuli and can maintain oxygen homeostasis. The reactive oxygen species (ROS) that are generated during influenza virus (IV) infection have critical effects on both the virus and host cells. In this review, we outline the link between viral infection and ROS production, using IV as an example. We introduce the current state of knowledge on the molecular relationship between cellular oxidation mediated by ROS production and various effects of IV infection. We also summarize the potential anti-IV agents that act by targeting oxidative stress.

A heterobifunctional reactive oxygen species (ROS)-responsive linker for directed drug assembly onto and delivery from a quantum dot (QD) nanoparticle carrier was synthesized and coupled to doxorubicin using EDC/sulfo-NHS coupling. The doxorubicin conjugate was characterized using ¹H NMR and LC-MS and subsequently reacted under conditions of ROS formation (Cu²⁺/H₂O₂) resulting in successful and rapid thioacetal oxidative cleavage which was monitored using ¹H NMR. The deprotected amine linker is amenable to peptide or protein conjugation prior to QD assembly or to direct conjugation to cognate reactive groups on ligands that cap the QD surface.

Asthma is a chronic inflammatory airway disease induced by many environmental factors. The inhalation of allergens and pollutants promote the reactive oxygen species (ROS) production leading to airway inflammation, hyper-responsiveness and remodeling in allergic asthma. The effects of asthma medications on ROS production are unclear. The present study investigated the anti-ROS effects of current asthma medications including inhaled corticosteroid (ICS; budesonide and fluticasone), leukotriene receptor antagonist (LTRA; montelukast), long acting β2 agonists (LABAs; salmeterol and formoterol) and a new extra-LABA (indacaterol). The human monocyte cell line THP-1 cells were pre-treated with different concentrations of the asthma medications at different time-points after hydrogen peroxide (H₂O₂) stimulation. H₂O₂ production was measured with DCFH-DA by flow cytometry. Montelukast, fluticasone and salmeterol suppressed H₂O₂-induced ROS production. Indacaterol enhanced H₂O₂-induced ROS production. Budesonide and formoterol alone had no anti-ROS effects, but the combination of these two drugs significantly suppressed H₂O₂-induced ROS production. Different asthma medications have different anti-ROS effects on monocytes. The combination therapy with LABA and ICS seemed not be the only choice for asthma control. Montelukast may be also a good supplemental treatment for the poorly-controlled asthma because of its powerful anti-ROS effects. Our findings provide a novel therapeutic view in asthma.

Background: In military flight operations fighter pilots work during flights constantly under hyperoxic breathing conditions with supplemental oxygen in varying hypobaric environments. These conditions are suspected to cause oxidative stress to neuronal organ tissues. For civilian flight operations the Federal Aviation Administration (FAA) also recommends supplemental oxygen for flying under hypobaric conditions equivalent to higher than 3048m altitude and makes it mandatory for conditions equivalent of more than 3657m altitude. Aim: We hypothesized that hypobaric-hyperoxic civilian commercial and private flight conditions with supplemental oxygen in a flight simulation in a hypobaric chamber at 2500m and 4500m equivalent altitude would cause significant oxidative stress in healthy individuals. Methods: 12 healthy subjects (6m, 6f, mean age 35,7yrs) from a larger cohort were selected to perform a 3hrs flight simulation in a hypobaric chamber with increasing supplemental oxygen levels (35%,50%,60% and 100% FiO2 via venturi valve equipped face mask) switching back and force between simulated altitudes of 2500m and 4500m. Arterial blood pressure and oxygen saturation were constantly measured via radial catheter and blood samples for blood gases taken from the catheter at each altitude and oxygen level. Additional blood samples from the arterial catheter at baseline and 60% oxygen at both different altitudes were centrifuged inside the chamber and the serum frozen instantly at minus 21°Celsius for later analysis of the oxidative stress markers malondialdehyde low density lipoprotein (M-LDL) and glutathione-peroxidase (GLP) via elisa test. Results: 11 subjects finished the study without adverse events. Whereas PO2 levels increased in the mean with increasing oxygen levels from baseline 96.2 mmHg to 160.9 mmHg at 2500m altitude and 60% FiO2 and 113.2 mmHg at 4500m altitude and 60% FiO2, there was no significant increase in both oxidative markers from baseline to 60% FiO2 at these simulated altitudes. Some individuals had a slight increase, some not at all or even a slight decrease. A moderate correlation (Pearson correlation coefficient 0,55) existed between subject age and glutathione peroxidase levels at 60% FiO2 at 4500m altitude. Conclusion: Supplemental oxygen of 60% FiO2 in a flight simulation comparing to flying in cabin pressure levels equivalent to 2500m-4500m altitude does not lead to a significant increase or decrease in the oxidative stress markers M-LDL and GLP in serum of arterial blood.

Synthesis of natural products with complicated architecture often requires segments having the functional groups that can be structurally transformed with the desired stereogenic centers. Bicyclic ?-lactones have a great potential for a suitable segment for natural product synthesis. However, the stereoselective construction of such functionalized bicyclic ?-lactones is not as straightforward as one might expect. On the other hand, the Lewis acid template-mediated Diels-Alder reaction is one of the most powerful and versatile methods for providing bicyclic ?-lactones with high regioselectivity and stereoselectivity. In this reaction, the Lewis acid template activates the dienophile as well as linking the diene and dienophile by a temporary tether. Therefore, Diels-Alder reaction smoothly proceeds in a stereocontrolled manner, allowing a simple access to bicyclic ?-lactone as a valuable building block for the synthesis of complicated natural products. In this review, some highlights of the Lewis acid-mediated Diels-Alder reaction, along with its application to the synthesis of biologically active compounds are discussed.