The properties of the annual, semiannual and triennial oscillations (AO, SAO and TO) in the middle atmosphere have been investigated using the TIMED/SABER temperature data. The Lomb-Scargle and wavelet spectra were used to determine the dominant oscillations in the background temperature field. The AO is prominent at the mid-latitudes. The AO amplitudes present an asymmetry between the two Hemispheres, being larger in the mesosphere than in the stratosphere. The SAO dominates the tropical regions, with three amplitude maxima at altitudes of 45, 75, and 85 km. The SAOs in the upper mesosphere (75 km) are out of phase with those in the mesopause (85 km) in the tropical regions, which can generate an enhancement of 11 K at each equinox, contributing to the lower mesospheric inversion layer. The TO is significant in the tropical region, with amplitude being maximum at 35, 45 and 85 km. Result shows that there may be potential interaction by the TO with SAO at 85km at the equator. The relation between ENSO and TO has also been discussed. The ENSO signal may modulate the amplitude of the TO, mainly in the lower stratosphere. The real origin of the TO may lie in the wave-mean-flow interaction.

The objective of this work was to evaluate the roast time, weight loss and quality of coffee grain at four different roasting degrees, aiming to recognize and develop sustainable patterns to industrialize specialty coffees. Coffee (Coffea arabica L.), from eight producers, with scores between 80 and 83 from SCA classification, were used. Samples of 300 g were roasted in a cylindric rotative roaster, until the grains reached four different roasting profiles (Agtron scale 22.36, #33.64, #40.05, #59.92). Afterwards, analysis of roasting time, gas pressure, weight loss, and sensorial grades were accomplished. It was observed that samples roasted at #22.36 led to significant differences, regarding roasting time and weight loss. Furthermore, there is a significant difference at the sensorial grades of the coffee beverage. Comparing the roast degree #40.05 (standard used for specialty coffee) with the roast degree #22.36 (most used for commodities coffee), the first one has a gas consumption of 0.34 kg per coffee kg, whilst the second presented a gas consumption of 0.41 kg per coffee kg. Thus, from gas consumption, roast degree # 40.05 is the more sustainable option, along with the remaining parameters analyzed.

Sustainable manufacturing practices are becoming increasingly necessary due to the growing concerns regarding climate change and resource scarcity. Consequently, material recycling technologies have gradually become preferred over conventional processes. This study aimed to recycle waste polylactic acid (PLA) from household-disposed cups and lids to create 3D-printed parts and promote sustainable manufacturing practices. To achieve this, the current study utilised virgin and post-consumer PLA (sourced from household waste) blends. The PC-PLA wastes were shredded and sorted by size with the aid of a washing step, resulting in a filament with a 1.70 ± 0.5 mm diameter without fragmentation or dissolution. A 50:50 wt.% blend of virgin PLA (vPLA) and PC-PLA was selected as the standard recycling percentage based on previous research and resource conservation goals. The study investigated the impact of three 3D printing parameters (layer height (LH), infill density (I), and nozzle temperature (NT))on the quality of 3D-printed parts using a three-level L9 Taguchi orthogonal array. The findings revealed that blending PC-PLA with vPLA led to significant improvements in the tensile, flexural, and impact strengths by 18.40%, 8%, and 9.15%, respectively, compared to those of recycled PLA. This conclusion was supported by the investigation of the fracture surface area, which revealed fractographic features associated with printing parameters, such as plastic deformation and interfilament debonding. An ANOVA analysis revealed a positive influence of larger layer height and high nozzle temperature on the mechanical properties. Subsequently, the optimal printing parameters (LH: 0.3 mm, I: 100%, and NT: 215 °C) were determined using the S/N ratio, and a confirmation test using the optimum printing parameters exhibited a strong correlation with statistically predicted outcomes. Finally, the study used optimum printing parameters to fabricate 100% post-consumer recycled PLA 3D printed parts, demonstrating their potential for low-strength applications. Based on these findings, it can be concluded that virgin and post-consumer recycled PLA blended filament for fabricating 3D printed components is an effective way to support plastic recycling in the context of a circular economy.

The effect of Mg particles on PLA's thermal, chemical, physical, and mechanical properties has been studied. The thermal and physical properties have been studied by differential scanning calorimetry, analysing the stability of the α and α’-crystals of the PLA. A colloidal route was used to introduce Mg particles inside the PLA matrix, ensuring a good dispersion of the particles. Materials with Mg contents from 0 to 10 wt.% have been prepared, with additions of polyethyleneimine (PEI) and polyethylene glycol (PEG). Fourier Transform Infrared Spectroscopy has been used to confirm the influence of Mg, PEI, and PEG on PLA properties. The mechanical properties have been measured with a universal tensile test machine on printed filaments via Fused Filament Fabrication (FFF), which were naturally aged to stable conditions. Filaments with and without a notch were studied to obtain the materials' tensile strength, elastic modulus, and fracture toughness. Different analytical models to explain the results of the PLA-Mg were studied, in which the interface strength of the PLA-Mg composites was calculated.

Several plant species produce mixtures of odorous and volatile compounds known as essential oils (EOs). These mixtures play important roles in nature and have been utilized by man for pharmaceutical and agrochemical purposes. There are more than 3000 EOs reported in the literature with approximately 300 having commercial use, including the oils from Eucalyptus species. Such oils are rich in monoterpenes and have found applications as pharmaceuticals, agrochemicals, food flavorants and in the perfume industry. Such applications are related to their diverse biological and organoleptic properties. In view of their importance, we review in this article up to date information concerning chemical composition and biological activities of essential oils from different species of Eucalyptus. Among the 900 species and subspecies of the Eucalyptus genus¸ we examined 68 species. The studies associated with these species were conducted in 27 countries. We have focused on the antimicrobial, acaricide, insecticide and herbicide activities, hoping that such information will contribute in the advances of the research in this field. It is also intended that the information herein described can be useful in the rationalization of the use of Eucalyptus EOs as components for new pharmaceutical and agrochemical applications as well as food preservatives and flavorants.

Dengue virus (DENV) and chikungunya virus (CHIKV) are reemergent arboviruses that are transmitted by mosquitoes of the Aedes genus. During the last several decades, these viruses have been responsible for millions of cases of infection and thousands of deaths worldwide. Therefore, several investigations were conducted over the past few years to find antiviral compounds for the treatment of DENV and CHIKV infections. One attractive strategy is the screening of compounds that target enzymes involved in the replication of both DENV and CHIKV. In this review, we describe advances in the evaluation of natural products targeting the enzymes involved in the replication of these viruses.

This paper describes the preparation and description of four new complexes [Bu₂Sn(AA)Cl] (AA = glycine, DL-valine and L-leucine) and [Bu₂SnPhen₂] (Phen = DL-phenylalanine) They were characterized by elemental analyses of carbon, hydrogen, nitrogen, chlorine and tin; and by infrared, ^119mSn-Mössbauer and ^119mSn-RMN spectroscopies, and by the applications of TG and DSC techniques in dynamic helium atmosphere. For the [Bu₂Sn(AA)Cl], trigonal bipyramidal tin species, AA were coordinated bidentatedly by the carboxylic oxygen and by the NH₂ group. The [Bu₂SnPhen₂)], with tin atoms in trans-octahedral sites, had the Phen-coordinated by both carboxylic oxygen atoms.

In order to correct attenuated millimeter-wavelength (Ka-band) radar data and address the problem of instability, an attenuation correction methodology (attenuation correction with variation trend constraint; VTC) was developed. Using synchronous observation conditions and multi-band radars, the VTC method adopts the variation trends of reflectivity in X-band radar data captured with wavelet transform as a constraint to adjust reflectivity factors of millimeter-wavelength radar. The correction was evaluated by comparing reflectivities obtained by millimeter-wavelength cloud radar and X-band weather radar. Experiments showed that attenuation was a major contributory factor in the different reflectivities of the two radars when relatively intense echoes exist, and the attenuation correction developed in this study significantly improved data quality for millimeter-wavelength radar. Reflectivity differences between the two radars were reduced and reflectivity correlations were enhanced. Errors caused by attenuation were eliminated, while variation details in the reflectivity factors were retained. The VTC method is superior to the bin-by-bin method in terms of correction amplitude and can be used for attenuation correction of shorter wavelength radar assisted by longer wavelength radar data.

A new Mg-Zn-Zr-Ca alloy in powder state was obtained via mechanical alloying method, from pure elemental powder. Further, the obtained powder-alloy was processed by selective laser melting (SLM) procedure to obtain 3D printed samples for small biodegradable implants. A series of microstructural, mechanical and corrosion analysis were performed. The SEM analysis of powder-alloy reveal a good dimensional homogeneity, with uniform colored, no agglutinated and almost rounded particles, suitable for selective laser melting procedure. Further, the SLM samples reveal a robust and unbreakable morphology, with a suitable porosity and without undesirable balling effect. The tested Young’s modulus of the SLM samples, of 42 GPa, is close to cortical bone one, of 30 GPa. The corrosion tests performed in PBS (Phosphate-buffered saline) solution show that the corrosion parameters have a satisfactory evolution.

Curcumin (CUR) is a phytochemical with potent anticancer activities as demonstrated by both preclinical and clinical studies. CUR bioformulations, including loading in biodegradable polymers, have been explored to increase CUR’s solubility and chemical stability, control its release, and improve its delivery to cancer cells. In this study, copolymers comprising poly (L-lactide)-poly (ethylene glycol)-poly (L-lactide) (PLA-PEG-PLA) and poly (ethylene glycol)-poly (L-lactide)-poly (ethylene glycol) (PEG-PLA-PEG) were designed and synthesized to assess and compare their curcumin delivery capacity and inhibitory potency on MCF-7 breast cancer cells. Molecular dynamics simulations indicated that PLA-PEG-PLA has a higher propensity to interact with the cell membrane and more negative free energy, suggesting it is the better carrier for cell membrane penetration. Our characterization indicated that the microsphere copolymers were synthesized successfully. Of the two formulations, PLA-PEG-PLA experimentally exhibited better results, with an initial burst release of 17.5%, followed by a slow, constant release of the encapsulated drug up to 80%. PLA-PEG-PLA-curcumin showed a significant increase in cell death in MCF-7 cancer cells (IC50 = 23.01 ± 0.85 µM) based on the MTT assay. These data were consistent with gene expression studies of Bax, Bcl2, and hTERT which showed that PLA-PEG-PLA-CUR induced apoptosis more efficiently in these cells. Our study integrates in vitro and in silico approaches to identify an optimal co-polymer for the delivery of CUR to cancer cells.

An eight-sided prism sample, obtained from a hot-rolled AZ31 magnesium alloy sheet, was compressed at room temperature along the transverse direction to investigate the influence of local strain on twinning behavior using electron backscatter diffraction (EBSD) measurements. The octagonal surface of the sample was divided into distinct regions based on hardness distribution and metallographic observations. The EBSD maps of different areas show significant variations, suggesting that these areas experienced different local strain conditions. The EBSD measurements provided detailed data from three distinct regions, with the strain state known in two regions and uncertain in the third. The combined analysis of the Schmid factor (SF) and the strain compatibility factor (m') was employed to study twin variant selection. The comparison of twinning behavior in different regions showed that the strain compatibility factor offered a more comprehensive explanation for the observed twinning pattern in the region with local shear strain.

Euler-Poisson equations of a charged symmetrical body in external constant and homogeneous electric and magnetic fields are deduced starting from the variational problem, where the body is considered as a system of charged point particles subject to holonomic constraints. The final equations are written for the center-of mass-coordinate, rotation matrix and angular velocity. General solution to the equations of motion is obtained for the case of a charged ball. For the case of a symmetrical charged body (solenoid), the task of obtaining the general solution is reduced to the problem of a one-dimensional cubic pseudo-oscillator. Besides, we present a one-parametric family of solutions to the problem in elementary functions.

Solid tumours are characterized by an altered microenvironment (TME) from the physi-cochemical point of view, displaying a highly hypoxic and acidic interstitial fluid. Hy-poxia results from uncontrolled proliferation, aberrant vascularization and altered can-cer cell metabolism. Tumour cellular apparatus adapt to hypoxia by altering its metab-olism and behaviour, increasing its migratory and metastatic abilities by acquisition of a mesenchymal phenotype and selection of aggressive tumour cell clones. Extracellular acidosis is considered a cancer hallmark, acting as a driver of cancer aggressiveness by promoting tumour metastasis and chemoresistance by selecting for more aggressive cell phenotypes, although the underlying mechanism is still not clear. In this context, Ca2+ channels represent good target candidates due to their ability to integrate signals from the TME. Ca2+ channels are pH and hypoxia sensors and alterations in Ca2+ homeostasis in cancer progression and vascularization have been extensively reported. The present review will focus on Ca2+ permeable ion channels, with a major focus on TRP, SOC and PIEZO channels, that are modulated by tumour hypoxia and acidosis as well as the role of the resulted altered Ca2+ signals on cancer progression hallmarks. A deeper compre-hension of the Ca2+ signaling and acidic pH/hypoxia interplay will break new ground for the discovery of alternative and attractive therapeutics targets.

Material Extrusion is a popular additive manufacturing technology due to its low cost, wide market availability, ability to construct complex parts, safety, and cleanliness. However, optimizing the process parameters to obtain the best possible mechanical properties has not been extensively studied. This paper aims to develop ensemble learning-based models to predict the ultimate tensile strength, Young's modulus, and strain at break of PLA and PLA-CF 3D-printed parts, using printing temperature, printing speed, and layer thickness as process parameters. Additionally, the study investigates the impact of process parameters and material selection on the mechanical properties of the printed parts and uses Genetic Algorithms for multi-objective optimization according to user specifications. The results indicate that process parameters and material selection significantly influence the mechanical properties of the printed parts. The Genetic Algorithm successfully identifies optimal parameter values for the desired mechanical properties. Moreover, this work is the first to model Process-Structure-Properties relationships for an additive manufacturing process and to use a multi-objective optimization approach for multiple mechanical properties, utilizing ensemble learning-based algorithms and Genetic Algorithms.

The spin-1/2 quantum transverse Ising model, defined on a ladder structure, with nearest-neighbor and four-spin interaction on a plaquette, is studied by using exact diagonalization and finite-size-scaling procedures. The quantum phase transition between the ferromagnetic and paramagnetic phases has been obtained in the thermodynamic limit. The critical transverse field decreases as the antiferromagnetic four-spin interaction increases, and reaches a multicritical point. However, the exact diagonalization approach was not able to capture the essence of the dimer phase beyond the multicritical transition.

Wireless Sensor Network (WSN) and the sensing devices are considered part of the core components of the Internet of Things (IoT). Hence, the modeling of IoT-WSNs is fundamental to having a better understanding, management, and deployment of this kind of technology. A fundamental issue in WSN is energy consumption due to the inherent limitations of this resource in the sensor devices. On the other hand, several issues arise in heterogeneous scenarios due to the coexistence of different sensor devices. Therefore, the modeling process becomes challenging and must consider the different transmission and operation cycles and modes that the transmission protocol implements to assure successful functioning in terms of transmission, synchronization, and energy savings. A duty-cycled MAC WSN protocol (PSA-MAC) has been modeled based on a pair of two-dimensional Discrete-Time Markov Chain (2D-DTMC), whose solution in terms of stationary probability distribution is used by expressions that have been derived to evaluate the energy consumption of sensor devices that could be used for WSN-based IoT applications. Analytical results of average energy consumption are obtained, where the synchronization, data, and sleep periods of a full transmission cycle are considered in a heterogeneous scenario with different node classes and priority assignments. Also, the normal and awake operation cycles are considered to assure synchronization and energy savings. Moreover, the transmission schemes of SPT (transmission of single packets) and APT (transmission of packets in aggregation) are also considered in the model. These results are validated through discrete event-based simulations, and the obtained results are accurate.

The idea that the Earth system self-regulates in a habitable state was proposed in the 1970s by James Lovelock, who conjectured that life plays a self-regulatory role on a planetary-level scale. A formal approach to such hypothesis was presented afterwards under a toy model known as the Daisyworld. The model showed how such life-geosphere homeostasis was an emergent property of the system, where two species with different properties adjusted their populations to the changing external environment. So far, this ideal world exists only as a mathematical or computational construct, but it would be desirable to have a real, biological implementation of Lovelock's picture beyond our one Biosphere. Inspired in the exploration of synthetic ecosystems using genetic engineering and recent cell factory designs, here we propose such a living, microbial Daisyworld. This is based on a synthetic microbial ecosystem using pH as the external, abiotic control parameter. Several case studies are considering, including two, three and multiple species assemblies. Despite that oscillatory dynamics and chaos emerge in the latter case, it is shown that global regulation is also achieved in most cases as species diversity increases. The alternative implementations and their implications of this model in other synthetic biology scenarios, including ecosystem engineering, are outlined.

This study investigated defect formation and strain distribution in high Mg content Al-Mg alloys during normal rolling and cross-rolling processes. The finite element analysis (FEA) revealed the presence of wave defects and strain localization-induced zipper cracks in normal cold rolling, which were confirmed by experimental results. The concentration of shear strain played a significant role in crack formation and propagation. However, the influence of wave defects was minimal in the cross-rolling process, which exhibited a relatively uniform strain distribution. Nonetheless, strain concentration at the edge and center regions led to the formation of zipper cracks and edge cracks, with more pronounced propagation observed in the experiments compared to FEA predictions. Furthermore, texture evolution was found to be a crucial factor affecting crack propagation, particularly with the development of the Goss texture component which is observed by electron backscattered diffraction analysis at bending points. The Goss texture hindered crack propagation, while the Brass texture allowed cracks to pass through. This phenomenon was consistent with both FEA and experimental observations. To mitigate edge crack formation and propagation, potential strategies involve promoting the formation of the Goss texture at the edge through alloy and process conditions, as well as implementing intermediate annealing to alleviate stress accumulation. These measures can enhance the overall quality and reliability of Al-Mg alloys during cross-rolling processes. In summary, understanding the mechanisms of defect formation and strain distribution in Al-Mg alloys during rolling processes is crucial for optimizing their mechanical properties. The findings of this study provide insights into the challenges associated with wave defects, strain localization, and crack propagation. Future research and optimization efforts should focus on implementing strategies to minimize defects and improve the overall quality of Al-Mg alloys in industrial applications.

Over the past decades, research has escalated on the use of polylactic acid (PLA) as replacement for petroleum-based polymers. This is due to its valuable properties, such as renewability, biodegradability, biocompatibility and good thermomechanical properties. Despite possessing good mechanical properties comparable to conventional petroleum-based polymers, PLA suffers from some shortcomings such as low thermal resistance, heat distortion temperature and rate of crystallization, thus different fillers have been used to overcome these limitations. In the frame work of environmentally friendly processes and products, there has been growing interest on the use of cellulose nanomaterials viz. cellulose nanocrystals (CNC) and nanofibers (CNF) as natural fillers for PLA towards advanced applications other than short-term packaging and biomedical. Cellulosic nanomaterials are renewable in nature, biodegradable, eco-friendless and they possess high strength and stiffness. In the case of eco-friendly processes, various conventional processing techniques, such as melt extrusion, melt-spinning, and compression moulding, have been used to produce PLA composites. This review addresses the critical factors in the manufacturing of PLA-cellulosic nanomaterials by using conventional techniques and recent advances needed to promote and improve the dispersion of the cellulosic nanomaterials. Different aspects, including morphology, mechanical behavior and thermal properties, as well as comparisons of CNC- and CNF reinforced PLA, are also discussed

Ongoing investigations have highlighted that MIM of Mg shows high potential for mass production of small lightweight components as well as of degradable implants with complex geometry. However, prior research activities have shown that Mg reacts sensitively to atmosphere impurities like oxygen and specific thermal decomposition products of the used backbone polymers. Polyethylene based polymers reveal a negative influence on sintering of Mg while polypropylene based polymers behave uncritically. This work is highlighting that when hydrogen instead of argon atmosphere is used during sintering, the negative influence caused by carbon residuals at the particle boundaries can be prevented. Mg-0.9Ca elongation increased with a slight decrease in UTS revealing a strengthening effect of the carbon residuals at the particle boundaries. For pure Mg UTS could be increased from 7 MPa up to 80 MPa with elongation of 6% showing the positive effect of hydrogen on the sintering of Mg.

The COVID-19 pandemic remains a serious public health problem globally. During winter flu seasons, more aggressive SARS-CoV-2 infections with fatalities have been documented, indicating that influenza co-infections may significantly impact the disease outcome of COVID-19. Both influenza and SARS-CoV-2 viruses share many similarities in their transmission and cellular tropism for their replication in the human respiratory tract. However, it is still unclear how the two pathogens interplay to ensure their survival in the same lung microenvironment. In addition, clinical studies on influenza co-infections in COVID-19 patients do not provide conclusive evidence on how influenza co-infection mechanistically modifies the disease outcome in COVID-19. This mini-review discusses various viral as well as host factors that potentially influence the survival or synergism of these two respiratory pathogens in the infected lung microenvironment.

One of the drawbacks of natural fibers and their composites is their inherent hydrophilic nature. The effect of moisture on mechanical properties of a composite is irrefutable. This study deals with hygroscopic characteristics of Enset-PLA composites and its effect on the mechanical properties of the composite. To do this, injection molded composite specimens of different fiber volume fraction; plasticizer ratio, fiber length, and fiber age have been considered. The specimens are exposed to distilled water and the moisture absorption was monitored on a daily base. Subsequently, the specimens are subjected to mechanical loading to determine the effect of moisture on their Strength, Stiffness and strain at break strength. Lastly, individual and joint effects of considered factors have been scrutinized using optimal design of experiment. The result from the study shows that maximum and minimum moisture uptake is noticed for 25% and 10% fiber ratio respectively. Due to moisture effect, tensile and bending strength is decreased by 11% and 5% respectively for 15% fiber volume fraction; while 16% and 13% for 25% fiber volume fraction respectively. Increasing amount of plasticizer increases moisture resistance. The result indicate that Enset-PLA composite have competitive properties and stability when exposed to moisture.

In our study we investigated the accelerated aging process of PLA under 253.7 nm UV-C irradiation with the use of GPC, NMR, FTIR, DSC methods and formal kinetic analysis. The results of GPC and DSC indicated a significant degree of destructive changes in PLA macromol-ecules, while spectroscopic methods NMR and FTIR showed maintenance of PLA main structural elements even after a long time of UV exposure. In addition to that, the GPC method displayed the formation of a high-molecular fraction starting from 24 hours of irradiation, and an increase in its content after 144 hours of experiment. It has been showed for the first time that a distinctive feature of prolonged UV exposure is the occurrence of intra- and intermolecular radical recom-bination reactions, leading to the formation of a high-molecular fraction of PLA decomposition products. This causes the observed slowdown of the photolysis process. It was concluded that photolysis of PLA is a complex of physicochemical processes, the mechanism of which depends on morphological changes in a solid phase of the polymer under UV radiation.

Metal additive manufacturing (AM) has gained much attentions in recent years due to its advantages including geometric freedom and design complexity, appropriate to a wide range of potential industrial applications. However, conventional metal AM methods have high-cost barriers due to the initial cost of the capital equipment, support and maintenance, etc. This study presents a unique low-cost metal material extrusion (MME) technology. The filaments used have polylactic acid (PLA) as the matrix and metal powders (copper, bronze, stainless steel, high carbon iron, and aluminum) as reinforcements. Using the proposed fabrication technology, test specimens were built by extruding polymer/metal composite filaments, which were then sintered in an open-air furnace to produce solid metallic parts. In this research, the mechanical and thermal properties of the built parts are examined using tensile tests, thermogravimetric-, thermomechanical- and microstructural analysis.

The effects of post-treatment temperature-based methods on 1D single PLA filaments after FFF have been studied. This lets to decouple the variables related to the 3D structure (layer height, raster angle, infill density, and others) from the variables solely related to the material (molecular weight, molecular orientation, crystallinity, and others). PLA 1D filaments have been aged at 20, 39, 42, 51, 65, 75 and 80 ºC in a water-bath-inspired process in which the hydrolytic degradation of the PLA has been minimised for the ageing temperatures of interest. The evolution of the thermal and mechanical properties of the PLA filaments at different temperatures was recorded. Differential scanning calorimetry (DSC) was used to evaluate thermal and physical properties, in which the glass transition, enthalpic relaxation, crystallisation and melting reactions were analysed. Tensile tests were performed to evaluate the tensile strength and elastic modulus. The flow-induced molecular orientation, the degradation, the logistic fitting and the so-called summer effect –stabilisation of properties at higher temperatures– are discussed for assessing the safeness of accelerating ageing.

Magnesium (Mg) alloy is a widely used lightweight metal structural material due to its high specific strength and stiffness, excellent damping performance, and recyclability. Wrought Mg alloys are widely favored in fields such as aerospace, transportation, and biomedical stents. However, most wrought Mg alloys with a hexagonal close-packed (HCP) crystal structure lack sufficient independent slip systems to meet the von Mises criterion for uniform plastic deformation at room temperature. This can result in the formation of strong basal texture during plastic deformation and poor room temperature plastic forming ability. Improving the room temperature forming performance is a crucial challenge that must be addressed to broaden the application of Mg alloy sheets. Our research group has comprehensively summarized significant work and latest research progress in improving the room temperature forming of Mg alloy sheets via extrusion technology in recent years. Specifically, we have developed a new type of asymmetric extrusion technology that combines material structure evolution, mechanical property, and forming behavior analysis. We have elucidated the extrusion process characteristics, texture control mechanism, and forming properties of Mg alloy sheets through plastic deformation mechanisms, mold design, and finite element numerical simulation. Our findings provide a novel extrusion technology for the fabrication of highly formable Mg alloy sheets, which can be utilized in various applications.

The study of ecosystems, both natural and artificial, has historically been mediated by population dynamics theories. In this framework, quantifying population numbers and related variables (associated with metabolism or biological-environmental interactions) plays a central role in measuring and predicting system-level properties. As we move towards advanced technological engineering of cells and organisms, the possibility of bioengineering ecosystems (from the gut microbiome to wildlands) opens several questions that will require quantitative models to find answers. Here, we present a comprehensive survey of quantitative modelling approaches for managing three kinds of synthetic ecosystems, sharing the presence of engineered strains. These include test tube examples of ecosystems hosting a relatively low number of interacting species, mesoscale closed ecosystems (or ecospheres), and macro-scale, engineered ecosystems. The potential outcomes of synthetic ecosystem designs and their limits will be relevant to different disciplines, including biomedical engineering, astrobiology, space exploration and fighting climate change impacts on endangered ecosystems. We propose a space of possible ecosystems that captures this broad range of scenarios and a tentative road map for open problems and further exploration.

On 11 March 2020, the COVID-19 emergency was declared and a large number of patients were admitted to the ICUs. Consequently, ICUs had to recruit nurses from other units as well as Nursing students without working experience in critical patients care. Since Critical nursing competence is crucial to avoid medical errors, the aim of this study was, to describe the level of safety and nursing competence in critical patient care of recruited nurses and students, during the COVID-19 pandemic in ICUs. A cross-sectional descriptive study of 66 participants using the validated competency assessment questionnaire for nurses in hospital care (COM-VA©) was performed. Our results showed that the level of safety perceived in critical patients care by the students on placement in ICUs and mentors scored higher than the rest of the participants. Interestingly, whereas the participant’s COM-VA© score indicated a level of competence good enough to work autonomously, the supervisor/mentor’s COM-VA© evaluation showed that only the group of students on placement obtained this level of competency. Altogether, we found that students on placement in ICU possesses a higher level of safety and COM-VA© scores than the rest of participants probably due to the close support of the mentor.

Scaffolds for tissue engineering are expected to respond to a challenging combination of physical and mechanical requirements, guiding the research towards the development of novel hybrid materials. This study introduces innovative three-dimensional bioresorbable scaffolds, in which a stiff poly(lactic acid) lattice structure is meant to ensure temporary mechanical support, while a bioactive gelatin-chitosan hydrogel is incorporated to provide a better environment for cell adhesion and proliferation. The scaffolds present a core-shell structure, in which the lattice core is realized by additive manufacturing, while the shell is nested throughout the core by grafting and crosslinking a hydrogel forming solution. After subsequent freeze-drying, the hydrogel network forms a highly interconnected porous structure that completely envelops the poly(lactic acid) core. Thanks to this strategy, it is easy to tailor the scaffold properties for a specific target application, by properly designing the lattice geometry and the core/shell ratio, which are found to significantly affect the scaffold mechanical performance and its bioresorption. Compression stiffness and strength provided by poly(lactic acid) lattices are overall within the range of values displayed by human bone tissue and remain stable after prolonged immersion in water at body temperature for several weeks. On the other hand, the hydrogel undergoes gradual and homogeneous degradation over time, but the core-shell integrity and structural stability are nevertheless maintained during at least 7-week hydrolytic degradation tests. In vitro experiments with human mesenchymal stromal cells reveal that the core-shell scaffolds are biocompatible and their physical-mechanical properties and architecture are suitable to support cell growth and osteogenic differentiation, as demonstrated by hydroxyapatite formation. These results suggest that the bioresorbable core-shell scaffolds can be considered, and further studied, in view of clinically relevant endpoints in bone regenerative medicine.

The manufacturing parameters influence the properties of thermo-mechanically processed met-als such as Mg alloys. This paper presents how the mechanical properties, the microstructure and the degradation rate of extruded Mn-containing Mg-Gd-alloys can be modified. Gd as repre-sented REE-element is particularly interesting due to the influence on the texture development in Mg and therefore studied as a base alloy system. The contents of Gd were investigated be-tween 2 to 9 wt.% with Mn-addition of 0.5 and 1.0 wt.%. The grain sizes and the corresponding textures were modified by the extrusion parameters and the alloy content. It was shown that modification by Mn can decrease the grain size, but increase the degree of recrystallization and decrease the degradation rate in the biological medium compared to the binary Mg-Gd system from previous studies. The results suggest that the binary Mg-Gd system can be produced more efficiently by adding Mn and that the resulting properties are more robust.

The wealth of data obtained during the past 20 years using Laser-Induced Breakdown Spectroscopy (LIBS) indicates that the technique is very promising to detect small chemical contents of alloying elements. The potential of LIBS was looked more seriously during the past two decades or so as more data were obtained on Aluminum and steel to study the phenomena in the condition of local thermodynamic equilibrium and time-delay between a Q-switch laser and an intensified CCD camera. Since the past decade, some data on compounds were also shown to be useful in determining small concentrations of harmful elements. This manuscript is intended to show that the technique of LIBS performance is very promising in fields such as micro-machining, in alloying element analysis, surface cleaning and environmental applications even with lightweight spectrometers having a relatively low resolution, which can potentially be air-borne.

Current Li battery technology employs graphite anode and flammable organic liquid electrolytes. Thus, current Li battery is always facing the problems of low energy density and safety. Additionally, sustainable supply of Li due to scarce abundance of Li sources is another problem. All-solid-state Mg battery is expected to solve the problems owing to non-flammable solid-state electrolytes, high capacity/safety of divalent Mg metal anode and high abundance of Mg sources. Therefore, solid-state electrolytes and all-solid-state Mg battery have been researched intensively last two decades. However, realization of all-solid-state Mg battery is still far. In this article, we review recent research progress on all-solid-state Mg battery so that researchers can pursue recent research trend of all-solid-state Mg battery. At first, solid-state electrolyte research is described briefly in the categories of inorganic, organic and inorganic/organic composite electrolytes. After that, the recent research progress of all-solid-state Mg battery is summarized and analyzed. To help readers, we tabulate electrode materials, experimental conditions and performances of all-solid-state Mg battery so that the readers can find necessary information at a glance. In the last, challenges to realize the all-solid-state Mg batteries are visited.

Myasthenia gravis (MG) is a disease characterized by typical clinical and immunopathogenic pe-culiarities, which correlate with age and sex/gender. Accordingly, MG patients show thymic al-terations and auto-antibodies productions, that can be the expression of a different pathogenetic mechanism related to age and gender. This determines, in relation to age at and sex/gender, a dif-ferent MG onset, prognosis, and outcome. Therefore, diverse MG forms can be identified, classi-fied, and characterized in relation to their different features, and precisely there are early onset and late-onset forms of MG. It has been hypothesized that the cause of appearance the two diverse forms of MG can be ascribed mainly to the diverse genetic and epigenetic factors. In this narrative review, we will analyze and discuss about the interplay of age- and sex-related factors (i.e. genet-ic and epigenetic factors) related to two different MG forms and how they contribute to their di-verse pathogenesis.

High density polyethylene (HDPE) and poly(lactic) acid (PLA) blends with different ratios of both polymers, namely 30:70, 50:50 and 70:30, were produced. Polyethylene grafted maleic anhydride and a random copolymer of ethylene and glycidyl methacrylate, were also proposed as compatibilizers to modify HDPE-PLA optimal blends and were added in the amounts of 1, 3 and 5 wt.%. Blends properties have been evaluated through different aspects by performing tensile tests, scanning electron microscopy to analyze blend morphology and interfaces, and thermomechanical analysis through differential scanning calorimetry, thermo-gravimetric analyses and infrared spectroscopy. The second blend, the one with equal amounts of HDPE and PLA seems to represent a good balance between high amount of bio-derived charge and acceptable mechanical properties. This suggests a good potential of these blends, which would be a good starting point for the production of composites with lingo-cellulosic fillers.

Polylactic Acid (PLA) is an organic polymer commonly used in fused deposition (FDM) printing and biomedical scaffolding that is biocompatible and immunologically inert. However, variations in source material quality and chemistry make it necessary to characterize the filament and determine potential changes in chemistry occurring as a result of the FDM process. We used several spectroscopic techniques, including laser confocal microscopy, Fourier-Transform Infrared (FTIR) spectroscopy and photoacousitc FTIR spectroscopy, Raman spectroscopy, and X-ray photoelectron Spectroscopy (XPS) in order to characterize both the bulk and surface chemistry of the source material and printed samples. Scanning Electron Microscopy (SEM) and Differential Scanning Calorimetry (DSC) were used to characterize morphology, crystallinity, and the glass transition temperature following printing. Analysis revealed calcium carbonate-based additives which were reacted with organic ligands and potentially trace metal impurities, both before and following printing. These additives became concentrated in voids in the printed structure. This finding is important for biomedical applications as carbonate will impact subsequent cell growth on printed tissue scaffolds. Results of chemical analysis also provided evidence of the hygroscopic nature of the source material and oxidation of the printed surface, and SEM imaging revealed micro and sub-micron scale roughness that will also impact potential applications.

Yellow nanorod Mg-MOF-74 was obtained by solvothermal synthesis method. XRD、N2 adsorption-desorption isotherms、SEM and TGA results suggest that the particle size of Mg-MOF-74 reaches 400 nm after the introduction of sodium acetate in the precursor of Mg-MOF-74. Besides, the morphology of Mg-MOF-74 was changed from cauliflower to rod particles. At the same time, the BET specific surface area and pore volume of Mg-MOF-74 were also increased a lot. Then the CO2 dynamic adsorption capacity of Mg-MOF-74 was measured by self-made fix bed under 30 ℃、0.1 bar CO2 partial pressure. The results show that the CO2 adsorption capacity of Mg-MOF-74-N2 reaches 3.67 mmol/g and its CO2 adsorption capacity remains unchanged after 10 times CO2 adsorption-desorption cycles.

In this study, the effects of various beryllium (Be) addition (Be-free, 0.1, 0.25, 0.50 wt.%) on the microstructure, mechanical properties, and corrosion corrosion of the Al-Mg-Li alloys were systematically investigated. The best performance was obtained in alloy with 0.1 wt.% Be addition. Trace Be addition promotes the grain refinement of the as-cast alloy ingot and contributes positive effects to the recrystallization, bringing improvement of tensile property. Meanwhile, the best anti-corrosion behavior is also presented at 0.1 wt.% Be addition, due to its potential to reduce the width of precipitates free zone (PFZ). As the Be content increase to an excessive level, the comprehensive performance decreases. Therefore, it is strongly recommended that adding trace Be element into Al-Mg-Li alloys has a positive effect on the comprehensive service performance.

Poly (Lactic Acid) (PLA) / Ground Tire Rubber (GTR) blends using Dicumyl peroxide (DCP) as a crosslinking agent were prepared as a route to recycle wastes rubber from the automotive industry. The GTR were exposed to grinding and exhibited mechanical damage, traduced at the rubber network scale by chains scission and/or chemical cross-links breakage. Such damage is accompanied by a decrease of 80% of the rubber chains network density of the initial tire buffing but found independent on the type of grinding (cryogenic, dry ambient) or on the GTR size (from <400 µm to <63 µm). Moreover, the finest sieved GTR contain the largest the amount of reinforcing elements (carbon black, clay) that can be advantageously used in PLA/GTR blends. The melt-blending of these finest GTR particles obtained by cryo-grinding at an amount of 15 wt.% and in presence of the crosslinking agent (DCP), resulted in an optimum improvement of the ductility, energy at break and impact strength of the PLA/GTR blends as compared to neat PLA, while maintaining its stiffness. The results were attributed to (i) the good dispersion of the fine GTR particles into the PLA matrix, (ii) the partial re-crosslinking of the GTR particles and co-crosslinking at PLA/GTR interface and (iii) the presence of reinforcing carbon black into the GTR particles and clay particles dispersed into the PLA matrix.

Background: Gender differences characterize the prevalence and attitudes toward weight management. Despite limited evidence suggesting greater weight loss in women with anti-obesity pharmacotherapy, gender-specific analysis remains underexplored. This retrospective study aimed to evaluate the gender-specific response to liraglutide 3.0 mg treatment in people with obesity without type 2 diabetes (T2D). Methods: Data were collected from 47 patients (31 women, 16 men), with age > 18 years, BMI ≥ 30 kg/m^2, absence of T2D, and with exclusion of prior anti-obesity treatment, comorbidities, or bariatric surgery. Only patients who maintained the liraglutide 3.0 mg dose for at least 6 months were included. Results: Both sexes showed significant reductions in weight and BMI at 3 and 6 months. Men achieved greater weight loss (WL), BMI reduction, % WL, WL >5% and >10% than women, and they also showed more significant improvements in metabolic parameters (total and LDL cholesterol, Fibrosis-4 Index FIB-4). No significant gender differences were observed in glucose metabolism or renal function. Conclusion: This study showed a greater therapeutic effect of liraglutide 3.0 mg in men. Given men's higher risk of cardiovascular disease (CVD), and underrepresentation in clinical weight loss programs, these findings may increase male engagement and improve their CVD risk.

The crystal structure of quintinite, Mg4Al2(OH)12(CO3)·3H2O, from Jacupiranga alkaline complex (Cajati, São Paulo, Brazil) has been refined for two samples (91002 and C7029) using single-crystal X-ray diffraction data. The mineral crystallizes in the P-3c1 space group, a = 5.246/5.298, c = 15.110/15.199 Å for the samples 91002/C7029. The crystal structure consists of octahedral sheets with Mg and Al ordering according to the 3 × 3 superstructure. The Mg and Al atoms are coordinated by six hydroxylated oxygen atoms each with the average &lt;Mg–O&gt; and &lt;Al–O&gt; bond distances being in the ranges 2.022–2.053 Å and 1.974–1.978 Å, respectively. The interlayer structures are identical (in contradiction to the previous assumptions) and compose from disordered (CO3)2- groups and (H2O)0 molecules. The samples from Jacupiranga can be identified as quintinite-2T that is the second find of the polytype after the Kovdor alkaline complex (Kola peninsula, Russia). The powder X-ray diffraction pattern of quintinite-2T contains weak superstructure reflection at 4.57 Å (010) indicative of Mg and Al ordering. An important crystal-chemical criterion of quintinite is the interlayer distance (d00n-value) of ~ 7.56 Å, which is steady for natural specimens from various findings worldwide.

The stability and composting behaviour of monolayers and laminates of poly(lactic acid) (PLA) and starch with and without active extracts and cellulose fibres from rice straw (RS) were evaluated. The retrogradation of the starch throughout storage (1, 5, and 10 weeks) gave rise to stiffer and less extensible monolayers, with lower water vapour barrier capacity. In contrast, the PLA monolayers, with or without extract, did not show marked changes with storage. However, these changes were more attenuated in the bilayers that gained water vapour and oxygen barrier capacity during storage, maintaining the values of the different properties close to the initial range. The bioactivity of the active films exhibited a slight decrease during the storage, the antioxidant capacity being better preserved in the bilayers. All monolayer and bilayer films were fully composted within 90 days, but with different behaviour. The bilayer assembly enhanced the biodegradation of PLA whose monolayer exhibited a lag period of about 35 days. The active extract reduced biodegradation rate of both mono and bilayers but does not limit the material biodegradation within the time stablished in the Standard. Therefore, PLA-starch laminates, with or without the valorised fractions from RS, can be considered as biodegradable and stable materials for food packaging applications.

Composites with HDPE and PLA matrix have been tested to analyse the effect of natural fillers (wood flour, recycled waste paper and a mix of both fillers) and temperature on polymer degradation. Composting tests have been performed in both mesophilic (35°C) and thermophilic (58°C) conditions. Degradation development has been evaluated through mass variation, TGA and DSC. HDPE, as expected, did not display any relevant variation, confirming its stability under our composting conditions. PLA is sensibly influenced by temperature and humidity, with higher reduction of Mw when composting is performed at 58°C. Natural fillers seem to influence degradation process of composites, already at 35°C. In fact, degradation of fillers at 35°C allows a mass reduction during composting of composites, while neat PLA do not display any variation.

The present study evaluates the manufacturing parameters effects on the tensile properties of material composed by polylactic acid (PLA) with wood fibers known as Timberfill. The specimens were built through fused filament fabrication (FFF). The influence of four printing parameters (Layer height, Fill density, Printing velocity, and Orientation) are considered through a L27 Taguchi orthogonal array in order to reduce experimental runs. Tensile test is applied to obtain the response variable used as output results to perform the ANOVA calculations. Fill density is the most influential parameter on the tensile strength, followed by building orientation and layer height, whereas the printing velocity shows no significant influence. The optimal set of parameters and levels is found, being 75% fill density, 0○Z-axis orientation, 0.4 mm layer height, and 40 mm/s velocity as the best combination. Applying this combination showed 9.37 MPa in maximum tension. Lastly, five solid Timberfill specimens manufactured via injection molding technology were also tested and the results compared to the printed samples. The values of the elastic modulus, elastic limit, and maximum tension of the injected samples were almost twofold of those were obtained for the FFF samples, but the maximum elongation of injected specimens was fell sharply.

Background: The management of erectile dysfunction (ED) shows several grey zones and new treatments for reduce the percentage of patients who discontinued the treatment are required. Here, we aim to evaluate the role of a natural mixture of named Icarifil (L-Citrulline, L-Carnitine, Eruca vesicaria, Panax ginseng, Tribulus terrestris, Turnera diffusa, Taurine, Vitamin E, Zinc) in the management of patients with ED. Methods: From September 2022 to March 2023, all patients attending 3 urological institutions due to ED were randomized to receive: Icarifil 1 sachet every 24 h (Group 1) or Icarifil 1 sachet + tadalafil 5 mg 1 tablet every 24 h (Group 2) or tadalafil 5 mg 1 tablet daily (Group 3), for 3 months. All patients underwent urologic visit and dedicated questionnaires (IIEF-5, SEP-2, SEP-3) at the enrollment and at the follow-up evaluation (3 months). Patient Reported Outcomes (PROs) at the follow-up evaluation were used. Primary endpoint was the difference in the questionnaires at the follow-up visit when compared with enrollment among the study groups. Results: In the per-protocol analysis, 52 patients in the Group 1, 55 in the Group 2 and 57 in Group 3 have been analyzed. At the follow-up evaluation, IIEF-5 have been improved in all the 3 Groups between enrollment and follow-up evaluation, but a statistically significant difference has been reported between Group 2 (+7.4) versus Group 1 (+4.1) or 3 (+5.1), (p&lt;0.001; p&lt;0.001). Moreover, 47 patients (94.0%) in the Group 2 showed an improvement in the SEP questionnaires, when compared with the baseline, while 29 in the Group 1 (56.9%) and 42 in the Group 3 (82.3%) with a statistically significant difference (p=0.004; p=0.003) among the Groups. The PROs analysis reported a better efficacy and patients’ satisfaction in Group 2 when compared with Group 1 or 3. Conclusions: In conclusion, Icarifil is able to improve penile erectile function in mild–moderate ED and it is able to significantly improve the clinical efficacy of tadalafil 5 mg daily use. Icarifil could be represent an interesting alternative treatment in patients experiencing adverse effects or with contraindications for chronic treatment with PDE5-is.

Daptomycin is one of the last therapeutic resources for multidrug-resistant gram- positive bacteria. Despite its structural similarities with glycopeptides, its mechanisms of action and resistance are different, and in some respects are not completely understood. Mutations in several genes have been associated to daptomycin resistance, especially in mprF, walkR, rpoB and rpoC, but their role and importance remain to be elucidated. We have studied mutations in 11 genes, which have been previously associated to daptomycin non- susceptibility, in 9 daptomycin non-susceptible Staphylococcus aureus clinical isolates (daptomycin MIC: > 1mg/L). Susceptibility to daptomycin, vancomycin, linezolid, oxacillin, telavancin and dalbavancin were studied. walkR, agrA, cls1, cls2, fakA, pnpA, clpP, prs, rpoB, rpoC and mprF were amplified by PCR and sequenced. The sequences were compared with the S. aureus ATCC 25923 complete genome (GenBank gi: 685631213) by using BLAST® software. We did not find any changes in walkR, pnpA, prs and clpP. All isolates excepting isolate 5 showed a high number of significant mutations (between 13 and 25 amino acid changes) in mprF. Most isolates also showed mutations in rpo genes, cls genes and fakA. Daptomycin non-susceptibility in S. aureus clinical isolates seems to be reached through different mutations combinations when compared to S. aureus ATCC 25293. Especially mprF and cls1 showed a very high polymorphism in most isolates. Meanwhile, one isolate, St5, showed only single mutation in mprF (P314T).

In this study, the degradable superhydrophobic Mg/P/Z/F/H (magnesi-um/poly(-caprolactone)/zinc oxide/1H,1H,2H,2H-perfluorodecyltriethoxysilane (PFDTES)/ heating process) composite materials were prepared through one-step method for enhancing the corrosion resistance of AZ91D magnesium alloys. Electrochemical measurements showed that Mg/P/Z/F/H materials significantly improved the corrosion resistance of magnesium alloys in 3.5 wt.% NaCl. The self-cleaning, adhesion and stability tests suggested that Mg/P/Z/F/H composite materials had well self-cleaning properties, good adhesion strength and stability in wet atmosphere.

This paper presents a new method of process parameters optimization, adequate for 3D printing of PLA (Polylactic Acid) components. The authors developed a new Hybrid Manufacturing Equipment (HME), suitable for producing complex parts made from a biodegradable thermoplastic polymer, for environmental sustainability. Our new HME equipment is producing PLA parts by both additive and subtractive techniques, with the aim of obtaining accurate PLA components with a good surface quality. A design of experiments has been applied for optimization purposes. The following manufacturing parameters were analyzed: rotation of the spindle, cutting depth, feed rate, layer thickness, nozzle speed, and surface roughness. Linear regression models and neural network models were developed to improve and predict the surface roughness of the manufactured parts. A new test part was designed and manufactured from PLA, to validate the new mathematical models, which can now be applied for producing complex parts made from polymer materials.

Although researchers have proposed various indentation size effect (ISE) models, these models often involve different form and number of parameters that can make our wonder which is the best in existed ISE models. Three types of ISE test data, namely, normal ISE, reverse ISE and transition of normal to reverse ISE, are used to evaluate the sixteen ISE models. The comparatively study indicates that H-J, N-G-Fs, N-G-H, N-G-A and N-G-Qs models can accurately predict the normal ISE. The reason for this is that the friction stress that is not related to dislocation activities or the indentation size effect of plastic zone has been introduced into these models. Therefore, these two factors should be considered in future ISE models. The sixteen ISE models are originally proposed to describe the normal ISE of different materials. However, to our surprise, some of these models are able to capture the reverse ISE and the transition of normal to reverse ISE of different materials. The determination coefficients (DC) of the sixteen ISE models are also determined for different materials. For reverse ISE, the highest DC value for NiCSi, TC4 and PED Ni are given by the EXP, N-G-Fs and N-G-A models, respectively. For the transition of normal to reverse ISE, the N-G-YC, N-G-Fs, and N-G-H models produce the maximum DC for ZrO2, Cu and Y2O3-ZrO2, respectively. Moreover, the mean DC of the N-G-Fs model is the maximum among the sixteen ISE models, followed by the N-G-H model, but they cannot accurately predict the reverse ISE. Therefore, the N-G-Fs and N-G-H models should be further modified to accurately predict the reverse ISE.

The aim of this study was to analyse the biocompatibility of a material based on lactic acid (PLA)/polyhydroxybutyrate(PHB)/thermoplastic starch (TPS) in combination with additives (plasticizers: acetyltributyl citrate (ATBC) and oligomeric lactic acid ( OLA)). Three types of materials were tested: I: PLA/PHB/TPS + 25% OLA, II: PLA/PHB/TPS + 30% ATBC, III: PLA/PHB/TPS + 30% OLA. The 3D printing itself was preceded by the creation of filaments from granulate and the design of samples. A filament production machine – Composer 450 (3devo; The Netherlands) was used to produce the filaments. Experimental samples were produced by FDM technology on a 3D printer DeltiQ2 (Trilab, Czech Republic). The evaluation of the biocompatibility of the materials included cytotoxicity tests such as the monitoring of viability, proliferation, morphology of cells, and their settlement on the surface of the materials. The cell line 7F2 osteoblasts (Mus musculus) was used in the experiments. Based on the tests, results confirmed the significant influence of plasticizers and their proportions in the mixtures. PLA/PHB/ATBC + 25% OLA was evaluated as the optimal material for biocompatibility with 7F2 osteoblasts. The tested biomaterials have the potential for further investigation, with a possible change in the proportion of the plasticizer, which has a fundamental impact on their biological properties.

Cognitive networks have evolved to cope with uncertain environments in order to make reliable decisions. Such decision making circuits need to respond to the external world in efficient and flexible ways, and one potentially general mechanism of achieving this is grounded in critical states. Mounting evidence has shown that brains operate close to such critical boundaries consistent with self-organized criticality (SOC). Is this also taking place in small-scale living systems, such as cells? Here we explore a recent model of engineered gene networks that have been shown to exploit the feedback between order and control parameters (as defined by expression levels of two coupled genes) to achieve a SOC state. We suggest that such SOC motif could be exploited to generate adaptive behavioral patterns and might help design fast responses in synthetic cellular and multicellular organisms.

This research paper focuses on the synthesis and characterization of Cu-doped Mg-Co ferrites with varying compositions (Mg_0.6-xCo_0.4Cu_xFe₂O₄, where x = 0.0, 0.1, 0.2, and 0.3) using a solid-state reaction method. This paper also investigates the structural, morphological, magnetic, and electrical characteristics of synthesized Mg_0.6-xCo_0.4Cu_xFe₂O₄, where x = 0.0, 0.1, 0.2, and 0.3. The X-ray diffraction (XRD) technique confirms the ferrites spinel structure in the Fd-3m space group, with average crystallite sizes ranging from 57.29 to 48.57 nm. Fourier Transform Infrared (FTIR) spectroscopy verifies chemical and structural changes, while scanning electron microscopy (SEM) reveals cubic crystal growth with an average grain size of 1 to 1.5 μm. DC electrical resistivity decreases with increasing temperature and Cu²⁺ substitution, ranging from 1.4 x 10⁶ Ω-cm to 6.7 x 10⁵ Ω-cm. The study suggests a correlation between resistivity and Cu²⁺ concentration. Magnetic behaviour, studied using a Vibrating Sample Magnetometer (VSM), shows dependence on dopant concentration, with coercivity ranging from 157 Oe to 256 Oe. The results indicate potential applications in magnetic storage devices, antennas, transformers, and high-frequency electronics.

Al-Zn-Mg-Cu alloy has high specific strength, good corrosion resistance, fracture toughness and fatigue resistance. It is one of the most important structural materials in the fields of aviation, aerospace, weapons, transportation and so on, which plays a huge role in the field of aerospace.In order to optimize the strength, toughness and corrosion properties of Al-Zn-Mg-Cu alloy, alloying has always been the focus of research on Al-Zn-Mg-Cu alloy. The effects of main alloying elements, trace alloying elements and rare earth elements on the microstructure and properties of Al-Zn-Mg-Cu aluminum alloy were briefly introduced in the paper, and the future research directions were prospected.

According to research, we have learned that Mg and TiO2 are new types material of marine protective coatings. We found that the addition of Mg can improve the performance of Zn-Al coating passivation film, and TiO2 has excellent photocatalytic self-cleaning performance. In this paper Zn-Al pseudo alloy coating was prepared by cold spray technique, and Zn-Al-Mg-TiO2 pseudo alloy composite coating was prepared by adding Mg and nano-TiO2. The effects of Mg and TiO2 to the marine protective properties of Zn-Al coatings were studied by friction and wear test, dynamic salt water corrosion test, electrochemical test, scanning electron microscope(SEM), energy dispersive spectrometer(EDS) and super deep scene 3D microscope. The results show that the addition of Mg and nano-TiO2 not only fills the gap of the coating and improves the density of the coating, but also generates grid-like flocculent corrosion products on the surface of the coating which can gather other corrosion products to improve the density of corrosion products, reduce the friction coefficient and corrosion rate of the coating surface, effectively prevent the invasion of Cl- in solution, and improve the wear and corrosion resistance of the coating.

Formation of Fe- and Mg-rich smectite and zeolite under alkaline conditions is concerned as secondary minerals after alkaline alteration of bentonite in a repository of radioactive wastes. It might be crucial for safety assessment whether smectite will be formed or not as secondary minerals after alkaline alteration of bentonite. In present paper, Fe- and Mg-rich smectite which are currently interacting with hyperalkaline groundwater was found at Narra in Palawan, Philippines. Mineralogical and geochemical investigation was conducted to understand formation process of smectite and factors determined secondary mineral species. Our study revealed a certain amount of smectite may have been produced under hyperalkaline conditions, altered from amorphous or poorly crystalline material such as M-S-H and F-S-H. Key factor which decides smectite or zeolite as secondary minerals after alkaline alteration of bentonite might be whether nuclei of M-S-H and/or F-S-H will be formed or not. This might be decided by the presence of dissolved Mg2+ and Fe2+ in the system. Our suggested formation process of smectite under alkaline conditions is analogue with generally-accepted model of smectite formation that might have been occurred on early Mars.

In this study, additive manufacturing of reinforced parts using metallic wire as both a reinforcement component and a shape memory stimulus through Fused Deposition Modeling (FDM) was investigated. A Shape Memory Polymer (SMP) restores its original shape and recovers it upon specific stimuli. This research employed chromium-nickel metal wire as a reinforcing component to enhance mechanical properties and introduce the capability for thermal stimulation of polylactic acid (PLA) via electrical current using the "in-situ impregnation" method within FDM process. Reinforced specimens were fabricated with wire with two diameters of 0.1 and 0.15 mm, along with two volume percentages of 5 and 10. Comprehensive evaluations encompassing mechanical (tensile and flexural) and thermal properties of the printed specimens were conducted. The outcomes revealed a significant enhancement in both tensile and flexural properties of the polymer matrix due to the embedding metallic wire, even under elevated temperatures during bending test. Furthermore, the thermal properties of the reinforced specimens were examined by subjecting them to various voltages, resulting in temperature ranging from 36.4 to 150.1°C. These findings highlight the ability to tailor a wide range of mechanical properties and shape recovery in the reinforced specimens by carefully selecting the wire volume fraction, voltage, and wire diameter, thus regulating the materials properties with specific application requirements.

Coffee is one of the most popular beverages in the world. Annual coffee consumption continues to increase, but at the same time, it generates a large amount of spent coffee grounds from the brewing process, that arises environmental problems. An appropriate solution to manage these spent coffee grounds becomes crucial. Our project aims to discuss the feasibility of utilizing the spent coffee ground to synthesize polylactic acid as a recycling application for spent coffee ground. This paper will discuss the properties and potential recycling applications of spent coffee grounds, the brief production process of polylactic acid, and the potential process for converting spent coffee ground to lactic acid. From our review, it is feasible to utilize spend coffee ground as the primary sources for lactic acid production by bacteria fermentation, and further produce bioplastics, polylactic acids by ring-opening polymerization. Possible ways to improve the yield and corresponding cost analysis are also discussed.

In this work, zinc oxide (ZnO) thin film has been fabricated on glass substrate using pulse laser ablation (PLA) technique. The effect of laser pulses of 1000, 1500, 2000 pulses at laser energy 700 mJ as well as, laser energy of 600, 700, and 800 mJ at fixed laser pulses of 1500 pulse, with methanol as a solvent on the structural properties of prepared films using XRD, SEM and EDX. XRD results revealed that the ZnO thin films have hexagonal structure with polycrystalline in nature with preferred orientation of (002). Crystalline size was increased with the increasing of the pulses and at energy of 700 mJ and pulse of 1500 pulse seemed nanostructure like tree leaf. In addition, narrow FWHM and no phase change have been observed in all cases. SEM images showed that for all cases the films were homogenous with some island and cluster then cracking started to obtain with the increasing of increase the pulse number. EDX analysis showed that the prepared films were free of defects and contaminations.

Electrospun fiber scaffolds are widely used in small diameter vascular tissue engineering because they mimick organizational structure and biological function of natural extracellular matrix. However, there is still one problem of low patency rate in the long term. The main reasons are the mismatch of compliance and the easy formation of thrombus. Therefore, it is very important to promote the rapid endothelialization of small diameter tissue engineering blood vessels by regulating the topological structure and biological properties of electrospun fiber scaffolds. Firstly, crimped polylactic acid (PLA) fibers were prepared by heat treatment to mimick the crimped structure and nonlinear mechanical properties of the elastic membrane of blood vessel wall. It improved effectively the aspect ratio of human umbilical vein endothelial cells (HUVECs) and promoted lateral alignment and growth. Then, crimped PLA fibers with three levels of pore structure were prepared by thermal induced phase separation, vapor induced phase separation and laser ablation to enhance the degree of HUVECs infiltrarion and realize patterned cell growth. Crimped PLA fibers with three levels of pore structure promote rapid endothelialization of blood vessels, which is of great significance to achieve long term patency rate of small diameter tissue engineering blood vessels.

Additive manufacturing (AM) are used in several industries such as automotive, aerospace, and medical sciences. One of the most common devices used in additive manufacturing is fused deposition modeling (FDM) 3D printers. This fabrication method has different inputs that affect the quality of the parts. In this research, the bending fatigue properties of polylactic acid (PLA) biomaterial made with a 3D printer are investigated. To demonstrate the influence of printing parameters on fatigue lifetime, standard specimens with nozzle diameters of 0.2-0.6 mm, extruder temperature of 180-240°C, and print speed of 5-15 mm/s were printed. After performing fully-reversed bending fatigue tests, it was found that printed specimens at 180°C have the best fatigue lifetime in most cases. Accordingly, fatigue behavior improved by reducing the nozzle diameter. Printing at lower temperatures also improved fatigue lifetime. The printing speed affected the slope of the S-N diagram, known as the fatigue strength exponent.

The development of high complexity geometry parts is one of the main goals of the additive manufacturing technology. However, the failure of printed structures and the joining of different parts to create complex assemblies represents a real challenge in the research of efficient and sustainability techniques for the permanent assembly of polymers. Laser welding processes have been used as a single step method to join metals until years ago. Nowadays, the growing trend in the use of thermoplastics for additive manufacturing has led to the need to adapt this technique to materials with a very specific nature and more sensitive to thermal effects. Also, the possibility of transmitting the laser beam through transparent polymer layers allows to focus the energy supply on internal sections of the assembled components. In this research, an infrared laser marking system was used to join two different samples of polylactic acid manufactured by fused deposited modeling technology. In order to increase the effectiveness of the bonding process, a transparent and a dark sample have been used as assembly material, focusing the laser beam on the interface area of the two parts. By means of tensile tests, dimensional measurement and the use of optical microscopy techniques, a basis was established that links the supplied energy by laser to the joining performance.

Magnesium-silver alloys are of high interest for the use as temporary bone implants due to their antibacterial properties in addition to biocompatibility and biodegradability. Thin wires in particular can be used for scaffolding, but the determination of their degradation rate and homogeneity using traditional methods is difficult. Therefore, we have employed 3D imaging using X-ray near-field holotomography with sub-micrometer resolution to study the degradation of thin (250 μm diameter) Mg-2Ag and Mg-6Ag wires. The wires were studied in two states, recrystallized and solution annealed to assess the influence of Ag content and precipitates on the degradation. Imaging was employed after degradation in Dulbecco’s modified Eagle’s medium and 10% fetal bovine serum after 1 to 7 days. At 3 days of immersion the degradation rates of both alloys in both states were similar, but at 7 days higher silver content and solution annealing lead to decreased degradation rates. The opposite was observed for the pitting factor. Overall, the standard deviation of the determined parameters was high, owing to the relatively small field of view during imaging and high degradation inhomogeneity of the samples. Nevertheless, Mg-6Ag in the solution annealed state emerges as a potential material for thin wire manufacturing for implants.

The present study investigated the effects of alloying and nano-reinforcement on the mechanical properties (microhardness, tensile strength, and compressive strength) of Mg-based alloys and composites. Pure Mg, Mg-3Sn alloy, and Mg-3Sn+0.2GNP alloy-nanocomposite were synthesized by powder metallurgy followed by hot extrusion. The microstructural characteristics of the bulk extruded samples were explored using X-ray diffraction, field-emission scanning electron microscopy, and optical microscopy and their mechanical properties were compared. The microhardness, tensile strength, and compressive strength of the Mg-3Sn alloy improved when compared to those of monolithic Mg sample and further improvements were displayed by Mg-3Sn+0.2GNP alloy-nanocomposite. No significant change in the compressive strain to failure was observed in both the alloy and the alloy-nanocomposite with respect to that of the pure Mg sample. However, an enhanced tensile strain to failure was displayed by both the alloy and the alloy-nanocomposite.

This study aimed to assess the response of 3D printed PLA scaffolds biomimetically coated with apatite on human primary osteoblast spheroids and evaluate the biological response to its association with Bone Morphogenetic Protein 2 (rhBMP-2) in rat calvaria. PLA scaffolds were produced via 3D printing, soaked in simulated body fluid (SBF) solution, and characterized by physical-chemical, morphological, and mechanical properties. The in vitro biological response was assessed with human primary osteoblast (HOb) spheroids. The in vivo analysis was conducted through the implantation of 3D printed PLA scaffolds either alone, covered by apatite (PLA-CaP) or PLA-CaP loaded with rhBMP-2 (PLA-CaP+rhBMP-2) on critical-sized defects (8 mm) of rat calvaria. Increased cell adhesion and in vitro release of growth factors (PDGF, bFGF, VEGF) was observed for PLA-CaP scaffolds when pre-treated with FBS. PLA-CaP+BMP2 presented higher values of newly formed bone (NFB) than other groups at all experimental periods (p&lt;0.05), attaining 44.85% of NFB after 6 months. These findings indicate that functionalization of PLA scaffolds with biomimetic apatite can improve its biological properties in the presence of complex biological media. Its association with BMP2 may enhance bone repair, suggesting this strategy as a promising candidate for bone tissue engineering.

Hypoeutectic Al-Si-Cu-Mg alloys are promising candidates for use in automobile parts. Therefore, various attempts have been made to develop alternative casting technologies to improve the mechanical properties of cast alloys. In this study, the effects of modification with different levels of strontium (Sr) on primary and eutectic silicon (Si) in hypoeutectic Al-Si-Cu-Mg alloys were investigated. Using a gravity cast process, the Sr-modified samples were prepared from melts with four levels (100, 200, 300, and 400 ppm) of Sr. In addition, the wear properties of the cast samples were studied using a block-on-ring wear-testing machine. The sizes of the primary Si phases increased with increasing Sr content in the alloys. Moreover, more finely dispersed eutectic Si was observed with higher Sr content. In frictional wear tests, the specific wear rates of the test specimens decreased as the Sr content increased from 200 to 400 ppm. Coarse Si phases are considered to act as solid lubricants in the contact region during sliding.

The conformational state of the activation loop (A-loop) is pivotal for the activation of most protein kinases. Hence, the characterization of the conformational dynamics of the A-loop is important to increase our understanding of the molecular processes related to diseases and to support the discovery of small molecule kinase inhibitors. Here, we carry out a combination of Molecular Dynamics (MD) and Essential Dynamics (ED) analyses to fully map the effects of phosphorylation, ADP, and conformation disrupting (CD) inhibitors (i.e., CD532 and MLN8054) on the dynamics of the A-loop of Aurora-A. MD revealed that the stability of the A-loop in an open conformation is enhanced by single phospho-Thr-288, while paradoxically, the presence of second phosphorylation at Thr-287 decreases such stability and renders the A-loop more fluctuant in time and space. Moreover, we found that such post-translational modification has a significant effect on the direction of A-loop motions. ED analysis suggests that the presence of the phosphate moiety induces the dynamics of Aurora-A to sample two distinct energy minima, instead of a single large minimum, as in unphosphorylated Aurora-A states. This suggests that the conformational distributions of Aurora-A with both single and double phospho-threonine modifications are remarkably different from the unphosphorylated state. In the closed states, binding of CD532 and MLN8054 inhibitors has the effect of increasing the distance of the N- and C-lobes of the kinase domain of Aurora-A, and the angle analysis between those two lobes during MD simulations showed that the N- and C-lobes are kept more open in presence of CD532, compared to MLN8054. As the A-loop is a common feature of Aurora protein kinases, our studies provide a general description of the conformational dynamics of this structure upon phosphorylation and different ligands binding.

Biomineralization has become a research hotspot and attracted widespread attention in the field of carbonate sedimentology. In this study, Bacillus licheniformis DB1-9 was used to induce the calcium carbonate precipitation at different magnesium calcium molar ratios in the laboratory to further explore the biomineralization mechanism. Phylogenetic tree shows that the bacteria belongs to Bacillus licheniformis species. The ammonia and carbonic anhydrase can be released by this bacteria, resulting in the pH increase, and the carbonic anhydrase can also promote the hydration reaction of carbon dioxide and subsequently produce the bicarbonate and carbonate ions to elevate the supersaturation of calcium carbonate in the liquid culture medium to facilitate the precipitation of carbonate minerals. The calcites have a shape of rhombohedron, dumbell, and elongation, and aragonite often appears in the form of mineral aggregates, besides that there are also the spherical and the fusiform minerals. FTIR result shows there are some organic functional groups, such as C-O-C and C=O, beside of the characteristic peaks of the calcite and the aragonite, indicating that microbial metabolism is closely related to the mineral formation. The superthin slices of the bacteria analyzed by HRTEM, SAED, EDS and STEM show that the surface and EPS can adsorb a large number of calcium ions and magnesium ions and EPS may act as the nucleation sites, what’s more, the intracellular nanometer-scale sphere areas show the amorphous structures, and the intracellular calcium ions and magnesium ions suggeste that they can be transported from the outside to inside the cell by diffusion along the concentration grade from high to low. This study may provide some references to further understand the biomineralization mechanism induced by microorganisms in the laboratory and the field, and also helps to explore the reason of the transition of calcite sea to aragonite sea in the geological history.

Dynamic thermogravimetric (TG) analysis under nitrogen environment was used to understand the thermal decomposition process of 3D printing filaments made of wood-filled polylactic acid (PLA)/starch blend. The characteristic temperatures and apparent activation energy (AAE) of the filaments with various starch contents were calculated with well-known kinetic models by Friedman, Flynn-Wall-Ozawa, Coats-Redfern and Kissinger. With the increased starch content in the filament, the onset thermal decomposition temperatures of the filaments decreased gradually from 272.4 to 155.1°C. The thermal degradation degree became smaller, and the transitional temperature interval became larger with increased starch proportion. The AAE values of the three types of filaments with different starch ratios varied between 97 kJ/mol and 114 kJ/mol, depending on material composition and method of calculation. The improved understanding of thermal decomposition behavior of PLA-starch-wood composites can help develop more biodegradable PLA/starch-based filaments for 3D printing.

Fused deposition modeling (FDM) is widely applied in various fields due to its affordability and ease of use. However, it faces challenges such as achieving high surface quality, precise dimensional tolerance and overcoming anisotropic mechanical properties. This paper analyzes and compare the machinability of 3D printed PLA, PETG and carbon fiber reinforced PETG focusing on surface roughness and burr formation. A design of experiments (DoE) with a full factorial design was used, considering three factors: rotation speed, feed rate and depth of cut. Each factor had different levels: rotational speed at 3000, 5500 and 8000 rpm; feed rate at 400, 600 and 800 mm/min; and depth of cut at 0.2, 0.4, 0.6, and 0.8 mm. Machinability was evaluated by roughness and burr height using a profilometer for all the materials under the same milling conditions. To evaluate the statistical significance of the influence of various processing parameters on surface roughness and burr formation in 3D printed components made of three different materials PLA, PETG and carbon fiber reinforced PETG, an analysis of variance (ANOVA) test was conducted. This analysis investigated whether variations in rotational speed, feed rate and depth of cut resulted in measurable and significant differences in machinability results. Results showed that milling parameters significantly affect roughness and burr formation, with optimal conditions for minimizing any misalignment highlighting the trade-offs in parameter selection. These results provide insights into the post-processing of FDM-printed materials with milling, indicating the need for a balanced approach to parameter selection based on application-specific requirements.

Understanding of the decisive role of the interaction mechanism and kinetics in the combustion processes is highly relevant for the elaboration of optimal conditions for obtaining Mo-Cu composite powders. From this perspective, the efficient delivery of the reduction mechanism of copper and molybdenum oxides with combined Mg + C reducing agents at high heating rates is crucial to develop a valuable approach for the combustion synthesis of Mo-Cu composite powders. Herein, we shed light on the mechanism of the reactions in all the studied binary, ternary and quaternary systems contemporaneously demonstrating the effect of the heating rate on the conversion degree. The combination of two highly exothermic and speedy reactions (MoO3+3Mg and CuO+Mg vs MoO3+CuO+4Mg) led to a slow interaction with weak self-heating (dysynergistic effect) due to a change in the reaction mechanism. On the other hand, it has been shown that during the simultaneous utilization of the Mg and C reducing agents, the process begins exclusively with carbothermic reduction, and at relatively high temperatures it continues with magnesiothermic one. The effective activation energy values of the magnesiothermic stages of the studied reactions were determined by Kissinger isoconversional method.

Present work has systematically investigated the evolution of dispersoid and elevated-temperature properties including the strength and creep resistance during the various multi-step heat treatments in Al-Mn-Mg 3004 alloys. Results show that only α-Al(MnFe)Si dispersoid is observed in the studied temperature range (up to 625°C) and it coarsens with increasing temperature to 500°C but dissolves at 625°C. The evolution of elevated-temperature strength and creep resistance is greatly related to the temperature of each step during the multi-step heat treatments. Generally, lower temperature at the first-step heat treatment leads to higher properties while the properties decrease with increasing temperature of last-step heat treatment. Suitable models have been introduced to explain the evolution of strength and the creep threshold stress at elevated-temperature during the various heat treatments.

Functionally graded materials (FGM) have attracted considerable attention in the field of composite materials and rekindled interest in research on composite materials, due to their unique mechanical response achieved through material design and optimization. Compared to conventional composites, FGMs offer several advantages and exceptional properties, including improved deformation resistance, improved toughness, lightness properties, and excellent recoverability. This study focused on the production of functionally graded (FG) polymer materials by additive manufacturing (AM) method. FG structures were produced by the Fused Deposition Modeling (FDM) method using Acrylonitrile benzidine styrene (ABS) and Polylactic acid (PLA) materials and tensile tests were performed according to ASTM D638. The effects of different layer thicknesses, volume ratios, and total thicknesses on mechanical behavior were investigated. In addition, tensile tests were carried out by producing single-layer samples at certain volume ratios to create a numerical model with the Finite element method to verify the experimental data. As a result of this study, it is presented that the FG structure produced with FDM improves mechanical behavior.

In horses, there is an increasing interest in developing long-lasting drug formulations, with bi-opolymers as viable carrier alternatives in addition to their use as scaffolds, suture threads, screws, pins, and plates for orthopedic surgeries. This communication focuses on the prolonged biocompatibility and biodegradation of PLA, prepared by hot pressing at 180 ºC. Six samples were implanted subcutaneously on the lateral surface of the neck of one horse. The polymers remained implanted for 24 to 57 weeks. Physical examination, plasma fibrinogen, and the mechanical noci-ceptive threshold (MNT) were performed. After 24, 28, 34, 38, and 57 weeks, the materials were removed for histochemical analysis using hematoxylin-eosin and scanning electron microscopy (SEM). There were no essential clinical changes. MNT decreased after the implantation procedure, returning to normal after 48h. A foreign body response was observed by histopathologic evalua-tion up to 38 weeks. At 57 weeks, no polymer or fibrotic capsules were identified. SEM showed surface roughness suggesting a biodegradation process, with an increase in the average pore di-ameter. As in the histopathological evaluation, it was not possible to detect the polymer 57 weeks after implantation. PLA showed biocompatible degradation and these findings may contribute to future research in the biomedical area.

Visceral leishmaniasis is a disease caused by protozoa of the species Leishmania (Leishmania) infantum (syn=Leishmania chagasi) and Leishmania (Leishmania) donovani, which are transmitted by hematophagous in-sects of the genera Lutzomyia and Phlebotomus. The domestic dog (Canis familiaris) is considered the main ur-ban reservoir of the parasite due to the high parasite load on its skin, serving as a source of infection for sand-fly vectors and, consequently, perpetuating the disease in the urban environment. Some factors are consid-ered important in the perpetuation and spread of canine visceral leishmaniasis (CVL) in urban areas, such as stray dogs with their errant behavior and houses that have backyards with trees, shade, and organic materi-als, creating an attractive environment for sandfly vectors. CVL is found in approximately 50 countries with the number of infected dogs reaching millions and, due to the difficulty of controlling and diagnosing the disease, the number of infected animals could be even greater. In the four continents endemic for CVL there are reports of disease expansion in endemic countries such as Brazil, Italy, Morocco, and Tunisia, as well as in areas where CVL is not endemic, for example, Uruguay. Socio-environmental factors, such as migration, drought, deforestation, and global warming, have been pointed out as one of the reasons for expansion to ar-eas where it had been absent. Thus, the objective of this review is to address (i) the distribution of CVL in endemic areas (ii) the role of the dog in the visceral leishmaniasis epidemiology and the factors that influence dog infection and spread of the disease, and (iii) the challenges faced in the control of CVL.

Chenodeoxycholic acid (CA) is a naturally occurring bile acid that is produced in the liver from cholesterol. Three CA complexes using Zn(II), Mg(II), and Ca(II) ions were synthesized to examine the chelation tendencies of CA towards these metal ions. The complexation reaction of CA with the metal ions under investigation was conducted with a 1:1 molar ratio (CA to metal) at 60-70°C in natural media (pH 7-8), which consisted of a binary solvent of MeOH and H2O (1:1). The resulting CA complexes were characterized using analytical data (metal, H, C, and Cl, analysis) and spectral data (UV-visible, FT-IR, and 1H NMR) to elucidate the complexes’ structures. The results suggested that CA in anion form utilized oxygen atoms of the carboxylate group (-COO−) to capture Zn(II), Mg(II), and Ca(II) ions. This produced complexes with the general compositions of [Zn(CA)(H2O)Cl], [Mg(CA)(H2O)Cl]H2O, and [Ca(CA)(H2O)Cl]2H2O, respectively. The Kirby-Bauer disc diffusion assay was then used to explore the bioactivity of the CA complexes toward three fungal species, three Gram-positive bacteria, and two Gram-negative bacteria. The Ca(II) and Mg(II) complexes exhibited marked inhibitory effects on the cell growth of the fungal species Aspergillus niger with potency equal to 127% and 116% of the activity of the positive control, respectively. The Zn(II) and Ca(II) complexes strongly inhibited the growth of Penicillium sp., while the Zn(II) and Mg(II) complexes showed strong growth inhibition towards the Gram-negative species Pseudomonas aeruginosa.

In this paper thermo-mechanical behavior of 4D printed Polylactic Acid (PLA) was investigated, focusing on its response to varying strain rates and temperatures below the glass transition temperature. Dynamic mechanical analysis and uniaxial tensile tests confirmed PLA's dependency on strain rate, showcasing its sensitivity to external stimuli. Stress-strain curves exhibited typical thermoplastic behavior, with yield stresses varying with strain rates, underscoring PLA's responsiveness to different deformation speeds. Clear strain rate dependence was observed, particularly at quasi-static rates, with temperature and strain rate fluctuations significantly influencing PLA's mechanical properties, including yield stress and deformation behavior. Isothermal compression tests demonstrated predictable stress-strain curves with distinct yield points, while adiabatic tests reveal additional complexities such as heat accumulation leading to further softening. Thermal imaging revealed temperature increase during deformation, highlighting the material's thermo-sensitive nature. These findings provide the basis for future research with the focus on advanced modeling techniques and mitigation strategies for self-heating effects, aiming to enhance PLA-based product reliability and performance in applications with deformations at higher strain rates, while also developing models to simulate shape recovery in 4D printed PLA structures at both cold and hot programming temperatures.

Selection of the most suitable material is one of the key decisions to be taken at the design stage of a manufacturing process. Traditional approaches as Ashby maps based on material properties are widely used in the industry. However, in the production of multimaterial components, the criteria for the selection can include antagonistic approaches. The aim of this work is the implementation of a methodology based on the results of process simulations for several materials and classify them by applying an advanced data analytics method based on Machine Learning (ML), in this case the Support Vector Regression (SVR) and Multi-Criteria Decision Making (MCDM) methodolo-gies, in this case Multi-criteria Optimization and Compromise Solution (VIKOR) combined with Entropy weighting methods. In order to do this, a Finite Element Model (FEM) has been built to evaluate the extrusion force and the die wear in a multi-material co-extrusion process of bimetallic Ti6Al4V-AZ31B billets. After applying SVR and VIKOR combined with Entropy weighting methodologies, a comparison has been established based on the material selection and complexity of the methodology used, resulting that material chosen in both methodologies is very similar and MCDM method is easier to implement because there is no need of evaluate the error of the pre-diction model and the time for data preprocessing is less than the time needed in SVR.

A homogenized, supersaturated Al-Zn-Mg-Zr alloy was processed by severe plastic deformation (SPD) using high-pressure torsion (HPT) technique for different revolutions at room temperature to get ultrafine-grained (UFG) microstructure. The microstructure and mechanical properties of the UFG samples were then studied by transmission electron microscopy (TEM), differential scanning calorimetry (DSC), as well as by tensile and hardness measurements. Emphasis was placed on the effect of shear strain on the evolution of microstructure of the investigated alloy. Experimental results have shown a very interesting evolution of the decomposed microstructure in a wide range of shear strains imposed by HPT. While the global properties, such as the average grain size (~200 nm) and hardness (~2.2 GPa) appeared unchanged, the local microstructure was continuously transformed. After 1 turn of HPT, the decomposed UFG structure contains relatively large precipitates inside grains. In the sample processed by 5 turns in HPT, segregation of Zn atoms into grain boundaries (GBs) can also be observed. After 10 turns, more Zn atoms have segregated into GBs and only smaller size precipitates can be observed inside grains. The intensive segregation of solute atoms into GBs may significantly affect the ductility of the materials, leading to its ultralow-temperature superplasticity. Our findings pave the way for achieving advanced microstructural and mechanical properties in nanostructured metals and alloys by engineering their precipitation and segregation by means of applying different HPT regimes.

In the context of high-temperature water vapor treatment, Zn-Mg-Al alloy-coated steel sheets exhibit the emergence of a black surface. This study aims to explore the factors and mechanisms contributing to surface blackening by inducing black surfaces on Zn-Mg-Al alloy-coated steel sheets, which were fabricated through molten coating subjected to water vapor treatment at 150 degrees Celsius. The surfaced composition was predominantly identified as ZnO, a zinc oxide film, validated through X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS). Morphological analysis of the surface and cross-section post-water vapor treatment revealed a disrupted lamellar structure with diffused features, resulting in the formation of an oxide film. Optical properties analysis demonstrated an increased absorbance and a decreased bandgap energy after water vapor treatment, indicative of an augmented blackening effect. Consequently, the high-temperature water vapor treatment led to the formation of oxides on the surface, with the highly reactive Mg and Al extracting oxygen from the predominantly present ZnO surface. This process resulted in the creation of an oxygen-deficient oxide, ultimately causing surface blackening.

The growing demands of material longevity in marine environments necessitate the development of highly efficient, low-cost and durable corrosion protective coatings. Although magnesium alloys are widely used in the automotive and aerospace industries, severe corrosion issues still hinder their long-term service in naval architecture. In present work, an epoxy composite coating containing sericite nanosheets is prepared on the AZ31B Mg alloy by one-step electrophoretic deposition method to improve corrosion resistance. Due to the PEI modification, positively-charged sericite nanosheets can be highly orientated in an epoxy coating under the influence of an electric field. The sericite-incorporated epoxy coating prepared in the emulsion with 4 wt.% sericite exhibits the highest corrosion resistance in 3.5 wt.% NaCl solution, as manifested by electrochemical corrosion and long-term immersion tests. The highly-orientated sericite nanosheets in epoxy coating provide excellent barrier effect against corrosive media, thereby significantly improving the long-term anti-corrosion performance of the epoxy coating. This work provides new insight toward the design of lamellar filler/epoxy coatings with superior anticorrosion performance and shows promise in the corrosion protection of magnesium alloys.

The effect of retrogression re-aging treatment (RRA) on corrosion behavior of 7055 Al-Zn-Mg alloy were studied. Results provides the corrosion resistance could be greatly improved by RRA. After the RRA treatment, the isolated precipitates occurred on grain boundaries (GBs) and the low angle grain boundaries (LAGBs) presented a larger fraction compared to the single-stage peaking aging. The samples after RRA treatment also show better corrosion resistance than the single-stage peak aging. The results of electrochemical impedance spectroscopy (EIS) show that impedance spectrum is consisted of semi-infinite layer diffusion impedance and stagnant Weber impedance. The semi-infinite layer diffusion impedance corresponded a limited retention layer on the electrode surface. In corrosion process, Weber impedance corresponded to stagnant layer of corrosion products generated by the anode branches. The RRA sample has the high Rf and low Cf, Cp values, and the corrosion current density of the RRA samples is ten times less than the single-stage peak aging samples with the 10% hardness losing.

Europium is the most-studied and least-well-understood rare earth ion (REI) dopant in GaN. While attempting to increase the efficiency of red GaN light-emitting diodes (LEDs) by implanting Eu⁺ into p-type GaN templates, the Strathclyde University group, in collaboration with IST Lisbon and Unipress Warsaw, discovered hysteretic photochromic switching (HPS) in the photoluminescence spectrum of doubly doped GaN(Mg):Eu. Our recent work, summarised in this contribution, has used time-, temperature- and light-induced changes in the Eu intra-4f shell emission spectrum to deduce the microscopic nature of the Mg-Eu defects that form in this material. As well as shedding light on the Mg acceptor in GaN, we propose a possible role for these emission centres in quantum information and computing.

The welding performance of shipbuilding steel under large heat input could be improved greatly by the Mg addition to the steel, but the impact toughness of the HAZ is not stable. According to the three different thickness steel plates obtained in the industrial experiment, the large heat input welding was carried out by different heat input, and the impact toughness analysis, impact fracture analysis, metallographic microstructure analysis and inclusions analysis were carried out. The results showed that, the HAZ of three kinds of thickness plates induced a lot of IAF, with Mg addition, the inclusion dimension had been reduced effectively, and the IAF induced ability of the inclusions had also been improved. The difference of HAZ impact toughness with different welding heat input and different impact temperature is significant, in consideration of the influence of welding heat input and metallographic microstructure on impact toughness of HAZ, the welding heat load had far greater effect than metallographic microstructure on ductile-brittle transition temperature. At the same time, if the original metallographic microstructure of steel was coarse, the pinning effect of the inclusions would be reduced significantly, and the microstructure of HAZ would be coarsened and the impact toughness of HAZ would be decreased, so there is a certain matching relationship between the metallographic microstructure and the inclusion dimension.

Rare earth rich magnesium alloys are used in aerospace and automotive fields because of their high specific strength and good castability. However, due to their low corrosion resistance, protective surface treatments, such as conversion coating or electroless plating are necessary, when they have to be used in humid or corrosive environments. The present study was aimed to evaluate the effect of Plasma Electrolytic Oxidation (PEO) and different surface roughness (Ra≈0.8 μm and Ra≈0.3 μm) on the rotating bending fatigue of an innovative Mg alloy, with a high content of Nd (up to 3.1 wt%) and Gd (up to 1.7 wt %). Fatigue tests revealed a 15% decrease in the fatigue strength of the PEO treated alloy (fatigue strength = 88 MPa) with respect to the bare alloy (fatigue strength = 103 MPa). The reduction of fatigue strength was mainly due to the residual tensile stresses induced by the PEO treatment. The effect of surface roughness on the bare alloy was, instead, negligible. The mechanisms of crack initiation were similar in the untreated and PEO treated alloy, with crack nucleation sites located in correspondence of large facets of the cleavage planes.

Fexuprazan is a potassium-competitive acid blocker approved for treating gastric acid-related diseases. Herein, we evaluated the pharmacokinetics (PKs) of single-dose and multiple-dose oral administration of fexuprazan 10 mg tablets in healthy subjects (Part 1) and investigated the bioequivalence between fexuprazan 10 mg and 40 mg tablets (Part 2). Part 1 comprised a single- and multiple-dose, 1-sequence, and 2-period design, and Part 2 comprised a single-dose, 2×2 crossover design. Eight and 23 subjects completed Parts 1 and 2, respectively. In Part 1, multiple doses accumulated twice as much as single doses. In Part 2, the geometric mean ratios [90% confidence intervals] for maximum plasma concentration (Cmax) and area under the concentration–time curve from zero to the time of the last quantifiable concentration (AUClast) of four fexuprazan 10 mg tablets to those of one fexuprazan 40 mg tablet were 1.0290 (0.9352–1.1321) and 1.0290 (0.9476–1.1174), respectively, which met bioequivalence criteria. Overall, favorable PK was observed after single and multiple administrations of one fexuprazan 10 mg tablet, and four fexuprazan 10 mg tablets were pharmacokinetically equivalent to one fexuprazan 40 mg tablet.

The phase composition design principle is introduced to obtain balanced properties of ionic conductivity and thermo-tolerant for zirconia solid electrolytes used in solid oxide fuel cells (SOFCs). The zirconia ceramic solid electrolytes are fabricated by two-step free sintering. With increasing Y/Mg ionic ratio from 1.78:1 to 1.88:1, the content of monoclinic phase fluctuates little (±3%). The ionic conductivity, including the total electrical resistance; grain electrical resistance and grain boundary electrical resistance at 1223K, are all gradually declining with the increasing of Y/Mg ionic ratio. Furthermore, the enrichment of Mg ion in grain boundary acts as a disincentive to grain boundary ionic conductivity. In addition, the maximum total equivalent conductivity at 1223K in this study reaches to 0.143 Scm-1 which can compare with that of certain YSZ. It will be beneficial to SOFCs application profited from increasing ionic conductivity of ceramic solid electrolytes.

Precipitates are the primary source of strength for the Al-Mg-Si alloy. Aluminum alloy in the peak-aged state mainly contain β'' and β' precipitates. In the past, most of the literature only considered the strengthening effect of β''. Here we develop a single crystal intensity model including both precipitate enhancement effects for the first time. This model was subsequently implemented into a crystal plastic finite element method to model the uniaxial tensile process of a polycrystalline aggregate model of Al-Mg-Si alloy. The simulation results for uniaxial stretching are in good agreement with the experimental results, confirming that the constitutive parameters used for the single crystal strength model with two precipitates are based on realistic physical implications. Furthermore, by comparing the uniaxial tensile simulation results of a peak-aged alloy considering the actual precipitated phase composition of the alloy with those assuming that the precipitated phase is only the β'' phase, the predicted tensile strength of the former is around 5.65% lower than that of the latter, suggesting that the two kinds of precipitation should be considered separately when simulating the mechanical response of Al-Mg-Si alloy. It is highly expected that the present simulation strategy is not limited to the Al-Mg-Si alloys, and it can be equally applied to the other age-enhanced alloys.

Yerba mate waste (YMW) were used to produce kombucha beverage, and the obtained microbial cellulose produced as by product (KMW) was used to reinforce mechanically recycled poly(lactic acid) (r-PLA) matrix. Microbial cellulosic particles were also produced in pristine yerba mate for comparison (KMN). To simulate the revalorization of industrial PLA products rejected during the production line, PLA was subjected to three extrusion cycles and the resultant pellets (r3-PLA) were then plasticized with 15 wt.% of acetyl tributyl citrate ester (ATBC) to obtain optically transparent and flexible films by solvent casting method. The plasticized r3-PLA-ATBC matrix was then loaded with KMW and KMN in 1 and 3 wt.%. The use of plasticizer allowed a good dispersion of microbial cellulose particles into the r3-PLA matrix, allowing to obtain flexible and transparent films which showed good structural and mechanical performance. Additionally, the obtained films showed antioxidant properties, as it was proven by release analyses conducted in direct contact with a fatty food simulant. The results suggest the potential interest of these recycled and biobased materials that are obtained from the revalorization of food waste for their industrial application in food packaging or agricultural films.

Different types of engineered cardiac constructs are being developed nowadays by many research groups. However, the immunological properties of such artificial tissues are not yet clearly understood. Previously, we have studied microfiber scaffolds carrying iPSC-derived cardiomyocytes. In this work, we evaluated the ability of these tissue-engineered constructs to activate the expression of CD28 and CTLA-4 proteins in T-lymphocytes which are early markers of the immune response. For this purpose electrospun PLA nanofibrous scaffolds were seeded with human iPSCs-CM and cultivated for 2 weeks. After, allogeneic mononuclear cells were co-cultured during 48 hours with 3 groups of samples that were tissue-engineered constructs, pure culture of cardiomyocytes and bare scaffolds followed by analysis of CD28/CTLA-4 expression on T-lymphocytes via flow cytometry. PLA scaffolds and concanavalin A (positive control) stimulation statistically significantly increased CD28 expression on CD4+ cells (up to 61.3% and 66.3%) and on CD8+ cells (up to 17.8% and 21.7%). CD28/CTLA-4 expression didn’t increase during co-cultivation of T-lymphocytes with cardiac engineered constructs and iPSC-CM monolayers. Thus, iPSCs-CM in monolayers and on PLA nanofibrous scaffolds didn’t cause T-cell activation, which allows us to expect that such cardiac constructs are not a cause of rejection after implantation.

The subject of the conducted study was focused on the development of new type of technical blends reinforced with natural fillers. The study was divided into two parts, where in the firsts stage of the research unmodified POM was reinforced with different types of natural fillers: cellulose, wood flour and husk particles. In order to select the type of filler intended for further modification, the mechanical characteristics was assessed. The 20% wood flour (WF) filler system was selected as the reinforcement. The second stage of research involved the use of combination of polyoxymethylene POM and poly(lactic acid) PLA. POM/PLA blend (ratio 50/50 %) were modified with elastomeric compound (EBA) and chain extender as reactive compatibilized (CE). The microscopic analysis revealed that for POM/PLA system the filler-matrix interface is characterized by better wettability, which might suggest higher adhesion. The mechanical performance revealed that for POM/PLA-based composites the properties were very close to the results for POM-WF composites; however, there is still large difference in thermal resistance in favor of POM-based materials. The increase in thermomechanical properties for POM/PLA composites occurs after heat treatment. The increasing crystallinity of the PLA phase allows for an significant increase of the head deflection temperature (HDT), even above 125 °C.

Disposable surgical gowns are usually made from petroleum-based synthetic fibers that do not naturally decompose, impacting the environment. A promising approach to diminish the environmental impact of disposable gowns involves utilizing natural fibers and/or bio-based synthetic fibers. In this study, composite web from polylactic bicomponent fiber and natural fibers, cattail and kapok fiber, were prepared by hot-press method. Only the sheath region of the PLA bicomponent fiber melts, acting as an adhesive that enhanced the strength and reduced the thickness of the composite web compared to its state before hot-pressing. Mechanical and physical properties of composite webs were evaluated. Composite webs created from kapok fiber displayed a creamy yellowish-white color, while those made from cattail fiber showed a yellowish-brown color. Composite webs exhibit hydrophobic properties when adding the natural fiber. The maximum natural fiber content, at a ratio of 30, can be incorporated into composite webs while preserving mechanical properties and proper water vapor permeability. This nonwoven material presents an alternative with the potential to replace petroleum-based surgical gowns.

In this study, differences in the kinetics of thermal-supported hydrolytic degradation of poly(lactic acid) (PLA) sample wet spinning fibres due to material variance in the initial molecular and supramolecular structure were analysed. The investigation was carried out at the microstructural and molecular levels by using readily available methods such as scanning electron microscopy, mass erosion measurement and estimation of intrinsic viscosity. The results show a varying degree of influence of the initial structure on the degradation rate of studied PLA fibres. The experiment shows that hydrolytic degradation at a temperature close to the cold crystallization temperature on a macroscopic level is definitely more rapid for the amorphous material, while on a molecular scale it is similar to a semi-crystalline material. Further, for the adopted degradation temperature of 90 °C, a marginal influence of pH of the degradation medium on the degradation kinetics was also demonstrated

In this study, the effect of increasing exposure time on microstructures, defectiveness, mechanical properties and corrosion behavior of selective laser melted sample Al-Si10-Mg powder have been investigated. The sample were processed at the same power (375 W) and scan speed (2000 mm/s) but with increasing exposure time. Exposure time equal to 40, 50 and 60 µs was applied. The features of the analyzed samples show that with increasing exposure time a better efficiency of the heat input has been obtained with larger size of melting pool and Si particles and lower defectiveness. Moreover, being the coarser microstructure associated a to lower level of voids, the average hardness is similar for the analyzed samples. The potentiodynamic curves of the samples show that the voids occurrence is more significant with respect to the scale of micro-structure on corrosion behavior being the sample processed at the highest exposure time the more resistant to corrosion. The experimental techniques used in the present study were Optical microscope, Sem microscope, Hardness and X-Ray Computed Tomography.

Al-6%Mg-Sc-Zr alloys with the total ratio of Sc + Zr = 0.32 wt.% make up the target of this research. The content of scandium and zirconium varied with an increment of 0.02%. The alloys were produced by induction casting. Their ultrafine-grained (UFG) microstructure was formed with Equal Channel Angular Pressing (ECAP). Such cast alloys have a homogeneous macrostructure formed by small equiaxed grains in the central part of the ingot and columnar crystals along the edges of the cross section. After ECAP, the average grain size in the alloy specimens is 0.5–1 µm. The average grain size does not depend on the ratio of Sc and Zr in these alloys. Superplasticity tests were performed at temperatures ranging from 300 to 500 °C and at a strain rate varying between 3.3·10-3 and 3.3·10-1 s-1. UFG Al-6%Mg-0.20%Sc-0.12%Zr and Al-6%Mg-0.18%Sc-0.14%Zr alloys exhibit the highest superplasticity. It was suggested that changes in Sc:Zr ratio affect spatial distribution and composition of the following precipitating particles: Al3Sc, Al3Zr, Al3(ScxZr1-x). An increase in Zr concentration is shown to reduce the susceptibility of UFG alloys to cavitation fracture.

Staphylococcus aureus is a Gram-positive bacterium causing a range of mild to life-threatening infections including bone infections such as osteomyelitis. S. aureus is able to invade and persist within non-professional phagocytic cells such as osteoblasts. In the present study four different S. aureus strains, 2SA-ST239-III, 5SA-ST5-II, 10SA-ST228-I, and 14SA-ST22-IVh were tested for their ability to modulate cell viability in MG-63 osteoblast-like cells following a successful invasion and persistence. Methicillin-sensitive S. aureus (MSSA) ATCC-12598-ST30 was used as control. Despite the demonstrated similar abilities of internalization and persistence of ATCC-12598-ST30, 2SA-ST239-III, and 14SA-ST22-IVh strains in MG-63 osteoblast-like cells under our experimental conditions, we demonstrated that the decrease in cell viability was due to the different behavior of the considered strains, with the number of intracellular bacteria playing a limited role. We focused our attention on different cellular biochemical functions related to inflammation, cell metabolism, and oxidative stress during osteoblast infections. We were able to show that: 1) ATCC-12598-ST30 and 2SA-ST239-III were the only two clones able to persist and maintain their number into the cellular hostile environment during the entire period of infection; 2) 2SA-ST239-III was the only clone able to significantly increase the gene expression (3 and 24 h) and protein secretion (24 h) of both interleukin-6 (IL-6) and tumor necrosis factor alpha (TNF-α) in MG-63 osteoblast-like cells; 3) the same clone determined a significant up-regulation of transforming growth factor-β1 (TGF-β1) and the metabolic marker glyceraldehyde 3-phosphate dehydrogenase (GAPDH) mRNAs at 24 h post infection; 3) neither the MSSA nor the four MRSA strains induced oxidative stress phenomena in MG-63 cells, although a very different expression pattern towards nuclear factor E2-related factor 2 (Nrf2) and its downstream gene heme oxygenase 1 (HO-1) activation was observed among the different clones. Our results can open a new way of considering therapies, going in the direction of an individualized therapeutic strategy that should take into account the difference existing between MSSA and MRSA as well as the distinctive features of the different clones. Not only, therefore, a different antibiotic approach but also a starting point for considering different host factors, i.e. the modulation of specific cytokines such as IL-6, TNF-α, and TGF-β1.

Background: This study explored maternal gut, breast milk and infant gut microbiomes as possi-ble mediators of the observed effects of a relaxation intervention which reduced maternal stress and promoted infant weight gain. Methods: A randomized controlled trial was conducted in healthy Chinese primiparous mother-infant pairs. Mothers were randomly assigned to interven-tion group (IG, listening to relaxation meditation) or control group (CG). Outcomes were differ-ences in microbiome composition and diversity in maternal gut, breast milk and infant gut at 1- and 8-weeks between IG and CG, assessed by 16S rRNA gene amplicon sequencing of fecal and breastmilk samples. Results: 38 mother-infant pairs were included in this analysis (IG=19, CG=19). Overall microbiome community structure in the maternal gut was significantly different between IG and CG at 1-week and the difference was more significant at 8 weeks (Bray-Curtis distance R2=0.04 vs. R2=0.13). Post-intervention, the α-diversity was significantly lower in IG breast milk (observed features: CG=295 vs. IG=255, p=0.032); the Bifidobacterium genera presented higher relative abundance. In parallel, significantly higher α-diversity was observed in IG infant gut (observed features: CG=73 vs. IG=113, p

Clay minerals surfaces potentially played a role in prebiotic synthesis through adsorption of organic monomers that give rise to highly concentrated systems; facilitate condensation and polymerization reactions; protection of early biomolecules from hydrolysis and photolysis; and surface-templating for specific adsorption and synthesis of organic molecules. This review presents processes of clay formation using saponite as a model clay mineral since it is shown to catalyze organic reactions, easy to synthesize in large and pure form, and has tunable properties. In particular, a method involving urea is presented as a reasonable analog of natural processes. The method involves a two-step process – 1) formation of the precursor aluminosilicate gel and 2) hydrolysis of a divalent metal (Mg, Ni, Co, Zn) by the slow release of ammonia from urea decomposition. The aluminosilicate gels in the first step forms a 4-fold-coordinated Al³⁺ similar to what is found in nature such as in volcanic glass. The use of urea, a compound figuring in many prebiotic model reactions, circumvents the formation of undesirable brucite, Mg(OH)₂, in the final product by slowly releasing ammonia thereby controlling the hydrolysis of magnesium. In addition, the substitution of B and Ga for Si and Al in saponite is also described The saponite products from this urea-assisted synthesis were tested as catalysts for several organic reactions including Friedel-Crafts alkylation, cracking and isomerization reactions.

The aim of this work is to assess the influence of Friction Stir Welding (FSW), process parameters, optimized tool traveling speed, and corrosion resistance of the 0.95 Mg-Al-alloy and pure copper weldment. Samples of aluminum-copper with and without deformation were characterized to investigate the metallurgical effects created during the welding deformation process. Effect of process parameters on microstructure and corrosion rate have been investigated for all the samples. All the electrochemical and polarization tests were done in 3.5 wt.% NaCl solution. Scanning Kelvin Probe (SKP) was done to detect the localized corrosion on the surface. Optical micrography observation indicated that the primary α-Al phase, which was formed during solidification can effectively limit the growth of Cu₉Al₄ phase. Finer acicular α-Al precipitates were observed in CuAl matrix during joining process that tends to coarser with the increase in tools travel speed. The electrochemical and polarization results showed that among all the tool travelling speed the specimen joined at tool travelling speed of 40 mm/min shows the best non-corrosive property.

This study analyzed the structural changes of semicrystalline polylactide (PLA) in the form of spun-bonded mulching nonwoven, during outdoor composting. The investigation was carried out at the microstructural, supramolecular and molecular levels using scanning electron microscopy (SEM), wide-angle X-ray diffraction (WAXD) and the viscosity method, respectively. The results showed the varying degree of influence of the climatic condition, prepared compost mixtures and time on the molecular, supramolecular and micromorphological structure of PLA spun-bonded mulching nonwoven and its degradation rate. The obtained experimental results revealed how the popular outdoor composting method, realized under two different European climatic conditions (in Poland and in Bulgary), affects the degradation of PLA nonwoven, designed for agriculture use.

Structural integrity is a crucial aspect of engineering components, particularly in the field of additive manufacturing (AM). Surface roughness is a vital parameter that significantly influences the structural integrity of additively manufactured parts. In this study, we present a comprehensive investigation into the relationship between surface roughness and structural integrity of Polyactic Acid (PLA) specimens produced through additive manufacturing. This research work focuses on the prediction of surface roughness of Additive Manufactured Polyactic Acid (PLA) specimens using eight different supervised machine learning regression-based algorithms. For the first time, Explainable AI techniques are employed to enhance the interpretability of the machine learning models. The eight algorithms used in this study are Support Vector Regression, Random Forest, XG Boost, Ada Boost, Catboost, Decision Tree, Extra Tree regressor, and Gradient Boosting regressor. The study analyzes the performance of these algorithms to predict the surface roughness of PLA specimens, while also investigating the impact of individual input parameters through Explainable AI methods. The experimental results indicate that the XG Boost algorithm outperforms the other algorithms with the highest coefficient of determination value of 0.9634. This value demonstrates that the XG Boost algorithm provides the most accurate predictions for surface roughness compared to other algorithms. The study also provides a comparative analysis of the performance of all the algorithms used in this study, along with insights derived from Explainable AI techniques.

Butyric acid as a histone deacetylase (HDAC) inhibitor was produced by a number of periodontal and root canal microorganisms (such as Porphyromonas, Fusobacterium etc.). Butyric acid may affect the biological activities of periodontal/periapical cells such as osteoblasts, periodontal ligament cells etc., and thus affect periodontal/periapical tissue destruction and healing. The purposes of this study were to study the toxic effects of butyrate on matrix and mineralization markers’ expression of MG-63 osteoblasts. Cell viability and proliferation were determined by 3-(4,5-dimethylthiazol-2-yl)-2,5-diphenyl tetrazolium bromide (MTT) assay. Cellular apoptosis and necrosis were analyzed by propidium iodide/Annexin V flow cytometry. Protein and mRNA expression of OPG, and RANKL were analyzed by western blotting and RT-PCR. OPG, soluble RANKL (sRANKL), 8-isoprostane, pro-collagen I, MMP-2, osteonectin (SPARC), osteocalcin and osteopontin secretion into culture medium were measured by enzyme-linked immunosorbant assay. Histone H3 acetylation levels were evaluated by immunofluorescent staining (IF) and western blot. We found that butyrate induced morphologic changes of growing MG-63 cells, with bigger and flattened in appearance. Butyrate activated histone H3 acetylation of MG-63 cells. Exposure of MG-63 cells to butyrate partly decreased cell number with no marked increase in apoptosis and necrosis. Butyrate stimulated RANKL protein expression, whereas it inhibited OPG protein expression. Butyrate also inhibited the secretion of OPG in MG-63 cells, whereas sRANKL level was below detection limit. Butyrate stimulated 8-isoprostane, MMP-2 and osteopontin secretion, but not procollagen I, osteonectin, osteocalcin in MG-63 cells. In conclusion, butyric acid generated by periodontal and root canal microorganisms may potentially induce bony destruction and impair bone repair by alteration of OPG/RANKL expression/secretion, 8-isoprostane, MMP-2, and osteopontin secretion, and affect cell proliferation. These effects are possibly related to increased histone acetylation. These events are important in the pathogenesis of periodontal and periapical destruction.