The present study aims at investigating the relationship between Initial Public Offerings (IPOs) variables mainly underpricing on one hand, and the brand value measures on the other. Our final data set is 104 international brand companies. We implement empirical approach using hierarchical OLS regression and descriptive statistics. We show that underpricing is positively related to brand value which emphasizes the marketing role of going public and underpricing in enhancing brand equity through the product market, which additionally confirms some information asymmetry models. We also find that on average brand companies had not been recognized as brands at the IPO time. Moreover, we show the positive role of private equity in enhancing brand value, additionally, the non-linear association between underpricing and brand value is not evident. Finally, we draw some policy implication and suggestions for future research.

Building energy consumption is the main urban energy consumption component, which mainly serves people-centered work and living energy demands. Based on the physical requirements of humans in urban buildings and to determine the comfortable body temperature in each season, this paper establishes a sizing optimization model of building-type integrated energy systems (IES), where the cooling and heating loads required to maintain indoor somatosensory body comfortable temperature are calculated. Depending on the external energy price, internal power balance and other constraints, the model develops an optimal sizing and capacity panning method of energy conversion and storage unit in a building-type IES with PV generation. The operating principle is described as follows: the PV generation is fully consumed, a gas engine satisfies the electric and thermal base load requirements, while the power system and a heat pump supply the remaining loads. The gas price, peak-valley electricity price gap and heat-topower ratio of gas engines are considered as important factors for the overall techno-economic analysis. The developed method is applied to optimize the economic performance of building-type IES and verified by practical examples. The results show that using the complementary characteristics of different energy conversion units is important to the overall IES cost.

In this paper, a study of modeling PV cell (solar cell), PV module (solar modules) and PV array solar array) using Matlab/Simulink software is presented. This study is focused on the study to design photovoltaic cell, photovoltaic modules, photovoltaic panels and PV array (solar array) and to analyze the change in PV performance according to changes in different parameters such temperature, solar irradiation, reverse saturation current, series resistance and shunt resistance. This study shows the PV and IV characteristics curve for each model from which MPP (maximum power point) is determined. In this study, different PV and IV characteristic curves are gained for varying temperatures with specified solar irradiation conditions,s and then the MPP is tracked. The highest power output is also compared between the designed PV module and the selected PV module (MX Solar USA MX60-245)

Solar energy is one of the most important renewable energy sources for many settings, such as households, solar-powered vehicles, power grid support, etc. However, the amount of solar energy produced is directly proportional to the surface area of the solar panel exposed to the sun rays, and so the challenges arise for the space required to install solar panels in order to get maximum area coverage of sun radiation energy absorption in constricted spaces such as vehicles powered by solar, small residential apartments, etc. The challenge with solar energy is that once a plate is installed, the space under it or above it cannot be used for another solar panel installation. This is due to the fact that the shadow cast by the above solar panel or structure prevents sun rays from reaching the below solar panel. The introduction of flexible solar panels that can take on any shape has given us the opportunity to explore the possibility of maximising solar plate surface area using surface manifold techniques. In this optimisation study, the constraint is that we have a space with fixed dimensions of length, width, and height, and the objective is to maximise the surface area of the panel within the given space dimensions to maximise solar energy absorption. Thus, this paper then proposes curving the panel surface and/or protruding the surfaces of the panel using the concept of a topology surface manifold to maximise the surface area: Protruding panel surface with shapes such as pyramidal, cone, hemisphere, sinusoidal wavy curve, etc. are analysed to check if the panel surface increases at all. The geometrical design result shows that the panel surface can increase by more than 20%. Although this paper only presents concept work and details of experimental design are yet to be performed, it should also be noted that curving surfaces have drawbacks, such as some protruding parts of solar panels when the plate is tilted, not facing the sun directly, which may cast shadows on parts of the solar panel, causing hindrance.

To enhance the safety of power grid operations, this study proposes a high-precision short-term photovoltaic power prediction method that integrates information from surrounding pho-tovoltaic stations and the Conv-LSTM-ATT model. In the deep learning prediction model, not only is numerical weather prediction (NWP) data from the target photovoltaic station used as input features, but also highly correlated features from nearby photovoltaic stations are incor-porated. The research begins by analyzing the correlation between irradiance and power se-quences, along with distance factors, to calculate a composite similarity index between the target and other regional photovoltaic stations. Stations with high similarity indices are then selected as data sources. Subsequently, Bayesian optimization techniques are employed to find the optimal data fusion ratios. Ultimately, using the selected data, power prediction mod-eling is conducted via the Conv-LSTM-ATT deep neural network. Experimental results con-firm the superiority of the proposed model, which demonstrates higher predictive accuracy compared to three other classical models. The data fusion strategy determined by Bayesian optimization significantly enhances prediction accuracy, reducing the root mean square error (RMSE) of the test set by 20.04%, 28.24%, and 30.94% for three weather types, respectively.

The optimization of photovoltaic (PV) systems is vital for enhancing efficiency and economic viability, especially under Partial Shading Conditions (PSCs). This study focuses on the development and comparison of traditional and advanced algorithms, including Perturb and Observe (P&O), Incremental Conductance (IC), Fuzzy Logic Control (FLC), Grey Wolf Optimization (GWO), Particle Swarm Optimization (PSO), and Artificial Neural Networks (ANN), for efficient Maximum Power Point Tracking (MPPT). Simulations conducted in MATLAB/SIMULINK evaluated these algorithms’ performance under various shading scenarios. The results indicate that while traditional methods like P&O and IC are effective under uniform conditions, advanced techniques, particularly ANN-based MPPT, exhibit superior efficiency and faster convergence under PSCs. The study concludes that integrating AI and ML into MPPT algorithms significantly enhances the reliability and efficiency of PV systems, paving the way for broader adoption of solar energy technologies in diverse environmental conditions. These findings contribute to advancing renewable energy technology and support the green energy transition.

Photovoltaic modules should pass series of tests and examinations, verifying the electrical and thermal characteristics of the module, before being released to the market, examining the properties of the modules should undergo appropriate durability and efficiency tests under real outdoor conditions with exposure to climatic conditions and under laboratory conditions. The performance of photovoltaic cells depends on many factors, such as solar irradiance, module operating temperature, installation location, weather conditions and module shading. In this paper, three selected photovoltaic modules were examined using a large-scale steady-state solar simulator. The current-voltage (I-V) characteristics of the photovoltaic modules were experimentally tested and analyzed. The next step was to implement a three-layer artificial neural network model (MLP). The experimental data obtained in the previous step coupled with output data from MLP were then used in global sensitivity analysis (GSA). Experiments carried out on a large-scale stationary solar simulator showed differences between the values declared by the manufacturer and the values obtained from measurements of PV modules. The first module tested achieved the maximum power point greater than that specified by the manufacturer, while the other two showed power drops; it was 85-87% for the second module, and 95-98% for the third, respectively. The performed global sensitivity analysis (GSA) for the MLP model showed that the parameters: eff (22.9) and Voc/V (14.19) have the largest effect on the power-voltage relationship, while U (7.29) has the smallest effect. The usefulness of machine learning (ML) methods in the comparative analysis of PV modules has been proved.

The paper addresses the energy consumption minimization problem in wireless powered communication networks (WPCNs) and proposes a DT-SWIPT-assisted time allocation scheme, named DaTA, such that the wireless station can share the remaining energy after transmission to the HAP to those who have not transmitted to the HAP to minimize the energy consumption of the network. In addition to proposing a new frame structure, the paper also considers the SNR (Signal-to-Noise) constraint to guarantee that the HAP can successfully receive data from wireless stations. In the paper, the energy consumption minimization problem is formulated as a nonlinear programming model. We employ the SQP (Sequential Quadratic Programming) algorithm to figure out the optimal solution. Moreover, a heuristic method is proposed as well to obtain a near-optimal solution in a shorter time. Simulation results showed that the proposed scheme can have better performance than the related work in terms of energy consumption and energy efficiency.

Safe water is a global public health concern amid increasing scarcity and pollution. Bottled water production and consumption contribute to these problems. This study examines tap water consumption in Italy, assessing associated sociodemographic factors and related health outcomes such as obesity and self-perceived health status. Data from the Italian National Statistics Institute's "Aspects of daily life" survey (N=45,597) were analyzed. Covariates included education, age, gender, economic status, region, concerns about waste and climate change, consumption of carbonated drinks excluding water, alcohol consumption, consumption of vegetables, consumption of snacks, body mass index, and self-perceived health status. Bivariate analyses and mixed-effect logistic regression models explored the associations. People who drink tap water were 19,674 with a higher prevalence in people aged 45 to 59 old, people with a graduate/post-graduate degree diploma, with optimal economic resources, and concerned about waste production and climate change, coming from the North-East regions of Italy. Underweight people showed a higher prevalence of TW assumption as well as those who drink less than occasionally carbonated drinks, drink alcohol, consume vegetables more than once a day, and snacks less than once a week with a satisfying level perceived health status. Regressions showed that all age classes are less likely to drink tap water than people younger than 20 years old. The category with “inadequate” economic resources is more likely to consume tap water. Low educational classes show a low likelihood of consuming tap water as well as Islands. A concern about waste production and climate change is associated with an increased likelihood of assuming tap water. Tap water consumption was negatively associate with obesity but not with a satisfactory Self-perceived health status. Insights from this study can inform public health strategies.

The geographical environment, food culture, and dietary habits are substantially different between the southern and northern regions in China. We investigated the associations with dietary patterns and metabolic syndrome between Chinese adult from the southern and northern regions (North: 1249; South: 1849) using data from the Chinese Health and Nutrition 2009 survey. Respectively, four dietary patterns were identified by factor analysis in the two regions. Each dietary pattern of factor score was calculated for three groups by tertile (T1<T2<T3). In the northern region, the association between the Alcohol and Western pattern and the risk of abdominal obesity (OR: 1.31; 95%:1.01, 1.68), hypertriglyceridemia (OR: 1.35; 95%:1.05, 1.74), high fasting blood glucose (OR: 1.37; 95%: 1.05, 1.80), and hypertension (OR: 1.55; 95%: 1.45, 1.99) was increased. In the southern region, the Convenience Food pattern was positively associated with hypertriglyceridemia (OR: 1.53; 95%: 1.03, 2.26), low HDL-cholesterol (OR: 1.96; 95%: 1.12, 3.43), and metabolic syndrome (OR: 1.79; 95%: 1.03, 3.11). The Alcohol dietary pattern was positively associated with high fasting blood glucose (OR: 1.83, 95%: 1.13, 2.97). There are some dietary pattern differences in the two regions. It is necessary to consider the factors of food culture and food intake habits in order to provide nutrition education to Chinese individuals from different regions in the future.

This paper describes a system that is used to gather data from Smart Home sensors measuring energy consumption, analyze and predict future consumption by using machine learning algorithm for prediction. It focuses on the architecture of the system as well as the need for such system to exist in practice – why the consumption should be measured at all and how that measurement can be put to good use for achieving energy efficiency.

This paper provides a comparative analysis of AES (Advanced Encryption Standard) and Salsa20 algorithm implementations, focusing on power consumption efficiency in passive RFID (Radio Frequency Identification) tags and ultra-low-power devices. The main objective of this work is to determine which of these algorithms is more suitable to operate in these types of devices. For this purpose, ASIC (Application-Specific Integrated Circuit) implementations of AES and Salsa20 based on low-power approaches were developed and their power consumption was evaluated. Results demonstrate that Salsa20 power consumption is lower than AES (2.82μW and 4.01μW, respectively - both in 0.18μm), indicating that Salsa20 is a better choice than AES for passive RFID tags.

Mass hauling operations play central roles in construction projects. They typically use many haulers that consume large amounts of energy and emit significant quantities of CO₂. However, practical methods for estimating the energy consumption and CO₂ emissions of such operations during project planning are lacking. This paper presents a detailed model for estimating the energy consumption and CO₂ emissions of mass haulers that integrates the mass hauling plan with a set of predictive equations. The mass hauling plan is generated using a planning program such as DynaRoad in conjunction with data on the productivity of selected haulers and the amount of material to be hauled during cutting, filling, borrowing, and disposal operations. This plan is then used as input for estimating the energy consumption and CO₂ emissions of the selected hauling fleet. The proposed model will help planners to assess the energy and environmental performance of mass hauling plans, and to select hauler and fleet configurations that will minimize these quantities. The model was applied in a case study, demonstrating that it can reliably predict energy consumption, CO₂ emissions, and hauler productivity as functions of the hauling distance for individual haulers and entire hauling fleets.

Little is known about public knowledge of meat chicken production and how it influences attitudes to birds’ welfare and consumer behaviour. We interviewed 506 members of the public in SE Queensland, Australia, to investigate this. Knowledge was assessed from 15 questions, and low scores were supported by respondents’ self-assessed report of low knowledge levels and agreement that their knowledge was insufficient to form an opinion about which chicken products to purchase. Older respondents and single people without children were most knowledgeable. There was uncertainty about whether chicken welfare was adequate, particularly in those with little knowledge. There was also evidence that lack of empathy towards chickens related to lack of knowledge, since those that thought it very acceptable that some birds are inadequately stunned at slaughter had low knowledge scores. More knowledgeable respondents ate chicken more frequently and were less likely to buy products with accredited labelling. Approximately half of the respondents thought the welfare of the chicken to be more important than the cost. It is concluded that the public’s knowledge has an important connection to their attitudes and consumption of meat chickens. Respondents with little knowledge demonstrated that they had both lack of empathy and intolerance to religious slaughter practices.

It is well known that working PV plants show several maintenance needs due to wiring and modules degradation, mismatches, dust and PV cells defects and faults. There are a wide range of studies that show the theoretical and some laboratory tests of how these circumstances may affect the PV production. Thus, it results mandatory to evaluate the whole PV plant performance and, then, it’s payback time, profitability and environmental impact or carbon footprint. However, very few studies include a systematic procedure to quantify and supervise the real degradation effects and faults impacts on the field. In this paper, the authors first conduct a brief review of the most frequent PV faults and degradation that can be found on real conditions operative PV Plants. Then, they propose and develop an innovative Geographic Information System application to locate and supervise them. The designed tool has been applied to either a large PV plant of 108 kWp and a small PV plant of just 9 kWp installed on a home rooftop. For the large PV plant, 24 strings of PV modules have been modelized and introduced into the GIS application and every module in the power plant has been studied including voltage, current, power, series and parallel resistance, fill factor, normalized PV curve to STC, thermography and visual analysis. For the small PV installation 3 strings of PV panels have been studied identically. It must be noticed that PV modules in this case include power optimizers. The precision of the study allows the researchers to locate and supervise up to a third part of every PV cell in the system, which are adequately georreferenciated. The developed tool allows both the researchers and the investors to increase control on the PV plant performance and conducts to a better planification of maintenance actuations and to evaluate several PV modules replacement strategies in a preventive maintenance programme. Found PV faults include hot spots, snail tracks, EVA discoloration, PV cells fractures, busbars discoloration, bubbles and Si discoloration.

In response to the problem of increasing climate change and energy security, investment in renewable energy sources has increased significantly both in Europe and globally. Wind and solar power plants are expected to be the largest contributors to global decarbonization, ranking first and second in projected capacity by 2050. Since all power plants have some impact on the environment, this also applies to photovoltaic power plants. Because of the large capacities projected for PV installed capacity, their environmental impacts should be evaluated. The environmental impacts of PV power plants change over time. Improving the manufacturing technology of PV system components, increasing the efficiency of solar cells, and using materials that are less harmful to the environment will reduce these impacts. Manufacturing PV system components is a highly energy-intensive process that involves greenhouse gas emissions. As new renewable energy capacity is built, the amount of "green" electricity on the grid increases, reducing CO2 emissions per kWh consumed. The objective of this paper is to analyze the current status of the environmental impact of PV power plants under these changing conditions in terms of CO2 emissions, land use, pollutant and noise emissions, and water consumption. The capacity installed to date will reach the end of its lifetime by 2050, which means that the amount of waste associated with it will increase over time. This can have a significant impact on the environment, which is why part of the work is dedicated to this problem. In addition to the available information from the literature, in the part related to land use, the authors also made their own estimates based on data on newly installed PV power plants and PV modules available on the market. The results of the analysis show that there is enough land both in Europe and worldwide to install the planned capacities of rooftop and ground-mounted PV power plants. CO2 emissions are at the same level as for concentrated solar power, with a decreasing trend. Pollutant emissions, noise and water consumption are not a major problem compared to other types of power plants. Overall, it can be concluded that the expansion of PV capacity has a very positive impact on the environment.

Parents play an important role in shaping the eating habits of their children through: appropriate selection of food products, snacking between meals and appropriate exposure to information from television advertisements, the press or the Internet. The level of parents' knowledge about proper nutrition and substances added to food is therefore crucial in promoting appropriate dietary choices in children and adolescents in order to prevent diet-related diseases. Objectives: Assessment of the consumption of snack foods by children and adolescents according to the surveyed parents and analysis of parents' knowledge about additional substances in food. Methods: The study was conducted among 129 parents of students from selected primary schools. The research tool was an original survey questionnaire consisting of 24 questions. Survey interviews were conducted with parents during meetings at schools. Statistical analysis was performed using the Pearson ch2 test, the significance level was set to p&lt;0.05. Results: Parents most often indicated sweets, confectionery products and sweetened drinks (25%) and vegetables or fruit (21%) as the form of snack for their children. 46% of children and adolescents drank sweetened drinks at least once a day. Parents had an average level of knowledge about food additives. Significant correlations were found between the level of knowledge of parents of school-age children about food additives and their level of education. Parents' knowledge and education did not significantly influence the level of snack consumption by their children. Children's eating behavior should be considered unsatisfactory. Conclusions: Research has shown the need for parents to be educated about food additives and to pay more attention to reading food labels so that they can reliably prepare their children to make the right food choices. Measures should be implemented to improve the eating habits of children and adolescents.

There are many uncertainties and risks in residential electricity consumption during the economic development. Knowledge of the relationship between residential electricity consumption and its key determinant—income—are important to the sustainable development of electric power industry. Using panel data from 30 provinces for the 1995-2012 period, this study investigates how residential electricity consumption changes as incomes increase in China. Previous studies typically used linear or quadratic double-logarithmic models imposing ex ante restrictions on the indistinct relationship between residential electricity consumption and income. Contrary to those models, we employed a reduced piecewise linear model that is self-adaptive and highly flexible and circumvents the problem of “prior restrictions.” Robust tests of different segment specifications and regression methods are performed to ensure the conservatism of the research. The results provide strong evidence that the income elasticity was approximately one, and it remained stable throughout the estimation period. The income threshold at which residential electricity consumption automatically remains stable or slows has not been reached. To ensure the sustainable development of the electric power industry, introducing higher energy efficiency standards for electrical appliances and improving income levels are vital. And government should emphasize electricity conservation in industrial sector rather than in residential sector.

One of the key areas of the International Renewable Energy Agency’s (IRENA) programme of work is the analysis of renewable technology costs and performance and the dissemination of these results to as wide an audience as possible. In addition to analysis, IRENA seeks to engage a broad range of stakeholders in the context of this work through the Renewable Costing Alliance. The Costing Alliance brings together companies, industry association, governments and researchers to share, confidentially, data for real-world renewable energy project cost and performance, helping to build further on IRENA’s costing work to date. In this context the authors analyse the current cost differentials and cost reduction potentials for solar PV in Japan compared to best practice levels and identify the reasons for higher costs in Japan and how to reduce them. This study analyses the current installed cost differentials for utility-scale, commercial and residential rooftop solar PV systems. In addition to identifying the reasons for the cost differentials, potential policy recommendations to reduce the cost differential are identified.

Ghana, blessed with abundant solar resources and has strategically invested in solar photovoltaic (PV) technologies to diversify its energy mix and reduce the environmental impacts of traditional energy technologies. The 50 MW solar PV installation by the Bui Power Authority exemplifies the nation's dedication to utilizing clean energy for sustainable growth. This study seeks to close the knowledge gap by providing a detailed analysis of the system's performance under different weather conditions, particularly on days with abundant sunshine and those with cloudy skies. The research consists of one-year monitoring data of the climatic and AC energy output fed into the grid. This data was used to analyze PV performance on each month's sunniest and cloudiest days. The results show that the total amount of AC energy output fed into the grid each month on the sunniest day varies between 229.3 MWh in December and 278.0 MWh in November, while the total amount of AC energy output fed into the grid each month on the cloudiest day varies between16.1 MWh in August and 192.8 MWh in February. Also, the percentage variation in energy produced between the sunniest and cloudiest days within a month ranges from 16.9% (December) to 94.1% (August). The reference and system yield analysis showed that the PV plant has a high conversion efficiency of 91.3%; however, only the sunniest and overcast days had an efficiency of 38% and 92%, respectively. The BPA plant's performance can be enhanced by using this analysis to identify erratic power generation on sunny days and schedule timely maintenance to keep the plant's performance from deteriorating. Optimizing a solar PV system's design, installation, and operation can significantly improve its AC energy output, performance ratio, and capacity factor on sunny and cloudy days.

Milk and dairy foods are naturally rich sources of a wide range of nutrients, and when consumed according to recommended intakes contribute essential nutrients across all stages of the life cycle. Since then, seminal studies recommendations with respect to intake of saturated fat have been consistent and clear; limit total fat intake to 30% or less total dietary energy, with a specific recommendation for intake of saturated fat to less than 10% of total dietary energy. However, recent work has re-opened the debate on intake of saturated fat in particular, with suggestions that recommended intakes be considered not at a total fat intake within the diet, but at a food specific level. A large body of evidence exists examining the impact of dairy consumption on markers of metabolic health, both at a total dairy intake and also at a food level, with mixed findings to date, but suggests that the impact of saturated fat intake on health differs both across food groups and even between foods within the same good group such as dairy. Milk and dairy foods contain a range of nutrients and bioactive components in different levels, housed within very different food structures. The interaction of the overall food structure and the nutrients describes the concept of the ‘food matrix effect’ which has been well documented for dairy foods. Studies show that nutrients from different dairy food sources can have different effects on health and for this reason, they should be considered individually rather than grouped as a single food category in epidemiological research. This review examines the current evidence from randomised controlled trials and meta-analyses, with respect to dairy, milk, yoghurt and cheese on aspects of metabolic health, and summarises some of the potential mechanisms for these findings.

Brown rice is a familiar whole grain in Japan. We examined national trends in brown rice consumption among Japanese adults aged ≥ 20 years old, using individual-level data from the National Health and Nutrition Surveys conducted between 2012 and 2019. We employed multivariable logistic regression to identify factors associated with brown rice consumption. The 95th percentile of daily brown rice intake remained at 0.0 grams throughout the study period. The percentage of brown rice consumers increased from 1.8% (95% confidence interval: 1.6–2.1) in 2012 to 2.3% (95% confidence interval: 1.8–3.0) in 2019. Compared with individuals who consumed only white rice, brown rice consumers had significantly higher mean intake levels of macronutrients, legumes, vegetables, fruits, and nuts. Brown rice consumption was positively associated with certain sociodemographic characteristics (being female, older age, residing in a major city, living without very young children, and having higher education levels) and health behaviors (lower body mass index, engaging in regular exercise, and being a former or never smoker). Despite its potential nutritional benefits in balanced diets, only a small fraction of adults in Japan consume brown rice, indicating a need for further promotion, particularly among individuals with characteristics associated with brown rice consumption.

Consumption of ultra-processed foods is associated with abdominal obesity, but this association has not yet been investigated in individuals on hemodialysis. This cross-sectional study, developed with 1014 individuals, aimed to analyze the prevalence of abdominal obesity and its association with the consumption of ultra-processed foods in individuals on hemodialysis. Consumption of ultra-processed foods was measured using a questionnaire, whose list of foods was based on the Surveillance System of Risk and Protective Factors for Chronic Non-Communicable Diseases through Telephone Enquiry. Waist circumference was used to determine the presence of abdominal obesity. The difference in proportions between the independent variables and the outcome was verified using Pearson's chi-square test. Hierarchical logistic regression was used to determine the association between the outcome and the independent variables. The prevalence of abdominal obesity was 77.22%. In the final model, higher consumption of ultra-processed foods, be male and an adult, have between 8 and 11 years of schooling and practice physical activity below the recommended level increased the chances of having abdominal obesity. The research provides a basis for the creation and improvement of public policies that promote improvements in these health determinants.

There are several challenges on how to attain energy efficiency while maintaining balance among factors affecting energy consumption such as power rating and temperature setpoints of cooling units, room temperature and humidity, and indoor air quality (IAQ). A real-time energy and IAQ monitoring system were installed in an educational building to profile the operational power consumption of inverter-based air condition unit (ACU) installed in each room. Polynomial curve and neural fitting regression analysis were applied to the real-time power consumption, indoor temperature and humidity, and carbon dioxide (CO2) level data. The derived models were able to provide the stabilizing indoor thermal and air conditions of the room to reach steady state ACU power consumption. These collected data and calculated parameters can be used to define rules in automating control of cooling appliances for an efficient energy utilization. The regression approaches, using real-time data, have determined the influence of indoor heat conditions and carbon dioxide levels on ACU power consumption. These parameters were utilized to establish consistent values for temperature, humidity, and carbon dioxide levels under stable settings of inverter-based air conditioning units.

Responsible, efficient, and environmentally conscious energy consumption practices are increasingly essential for ensuring the reliability of the modern electricity grid. This study focuses on leveraging time series analysis to improve forecasting accuracy, crucial for various application domains where real-world time series data often exhibit complex, non-linear patterns. Our approach advocates for utilizing Long Short Term Memory (LSTM) and Bidirectional LSTM (BiLSTM) models for precise time series forecasting. To ensure a fair evaluation, we compare the performance of our proposed approach with traditional neural networks, time-series forecasting methods, and conventional decline curves. Additionally, individual models based on LSTM, Bi-LSTM, and other machine learning methods are implemented for a comprehensive assessment. Experimental results consistently demonstrate that our proposed model outperforms all benchmarking methods in terms of mean absolute error (MAE) across most datasets. Addressing the imbalance between activations by consumer and prosumer groups, our predictions show superior performance compared to several traditional forecasting methods, such as the Autoregressive Integrated Moving Average model (ARIMA) and Seasonal Autoregressive Integrated Moving Average model (SARIMA). Specifically, the root mean square error (RMSE) of Bi-LSTM is 5.35%, 46.08%, and 50.6% lower than LSTM, ARIMA, and SARIMA, respectively, on the May test data.

This research presents a maximum power point tracking of traditional single-ended primary converter (SEPIC) with the aid of fuzzy logic controller (FLC) for regulating the voltage and perturbation and observation(P&O) algorithms for regulating the reference voltage and reaching the maximum power point tracking. This is a promising technique for the conventional SEPIC converter to achieve maximum power point tracking with much less error. Moreover, the method is simple, reliable, and understandable for photovoltaic systems.

Introduction Emergency laparotomy is a surgical procedure associated with significantly higher mortality rates compared to elective surgeries. Awake laparotomy under neuraxial anaesthesia has recently emerged as a promising approach in abdominal surgery to improve patient outcomes. This study aims to evaluate the feasibility and potential benefits of using lumbar spinal anaesthesia as the primary anaesthetic technique in emergency laparotomies. Methods We conducted a case series involving 16 patients who underwent emergency laparotomy for bowel ischemia, perforation, or occlusion. Lumbar spinal anaesthesia was employed as the main anaes-thetic technique. We analysed patient demographics, clinical characteristics, intraoperative details, and postoperative outcomes. The primary outcome measures included the adequacy of postoper-ative pain control, the incidence of postoperative complications, and mortality rates. Results Among the 16 patients, adequate postoperative pain control was achieved, with only 2 patients requiring additional analgesia. Postoperative complications, including sepsis, wound dehiscence, and pneumonia, were observed in 7 patients (44%). The observed mortality rate was relatively low at 6% (1 patient). Notably, conversion to general anaesthesia was not necessary in any of the cases, and no early readmissions were reported. Discussion Our findings highlight the feasibility and potential benefits of using neuraxial anaesthesia in emergency laparotomies. The observed low mortality rate and the avoidance of conversion to general anaesthesia suggest that lumbar spinal anaesthesia may be a useful alternative in emer-gency settings. However, the occurrence of postoperative complications in 44% of patients indi-cates the need for cautious patient selection and close monitoring. Further research with larger sample sizes is warranted to fully elucidate the efficacy, safety, and potential impact of this tech-nique on patient outcomes in emergency laparotomies.

This study aims to find countries that differ in their development of the agricultural sector in terms of environmental care and to examine the relationship between renewable and non-renewable energy consumption and agricultural sector production in European Union countries. The classification of countries was conducted using the principal component method and biplot. Panel data for the period 2000-2022 and a VAR model, an impulse response function (IRF) and causality tests were used for the study. The results indicate two distinct groups of countries that significantly differ in adopting green agricultural practices. Only seven EU countries stand out for sustainable agriculture with low pesticide use, a significant share of organic farms and high use of renewable energy in agriculture. Energy consumption affects agricultural production differently in the two groups of countries studied: in countries with sustainable agriculture, an increase in renewable energy consumption translates into a positive increase in agricultural production. On the other hand, an increase in non-renewable energy consumption shows a dampening effect on agricultural production growth, especially in countries with less sustainable agriculture. The study results highlight the need to promote renewable energy development in agriculture and raise awareness about the adverse environmental effects of intensive agriculture while emphasising the positive impact of organic agriculture on agricultural production.

Hybrid electric vehicles (HEVs) are perceived as a first step towards the future of sustainable transport. Of course, battery electric vehicles (EVs) are currently ideal for what is wanted to stand for transport in the future. The lack of infrastructure for these vehicles makes many potential users choose hybrid vehicles in these conditions. This paper analyzes the influence of the engine and electric motor of hybrid vehicles on their performances. Three engines with slightly different power and close characteristics were considered for configured models. Also, two electric motors with very different power but having a very close maximum continuous torque have been used in models. One is an induction motor, and the other is a permanent magnet synchronous motor. ADVISOR software has been used for vehicles configuration and simulation. Series and parallel hybrid vehicles have been considered. The main dynamic performances and the fuel consumption in two driving cycles were compared for the configured models. Three conventional models with the same engines used in HEVs have also been simulated for reference. The results highlight that in the case of HEVs, the choice of combination engine/electric motor is crucial in obtaining the best report between dynamic performances and low fuel consumption, and implicitly a low negative impact on the environment.

High-penetration of Distributed Energy Resources (DER) in low voltage distribution grids, mainly photovoltaics (PV), might lead to overvoltage in the point of common coupling. Volt-VAr is one of the common control functions for DER power converters used to enhance the stability and the reliability of the voltage in the distribution system and, thus, fulfilling the network operator requirements. In this study, a centralized algorithm will provide local Volt-VAr control parameters to each PV inverter, based on the electrical grid characteristics where each equipment is installed. Since accurate information of grid characteristics is typically not available, the parametrization of the electrical grid is done using power meter data in DER location and a voltage sensitivity matrix. The algorithm has different optimization modes to both minimize voltage deviation and line current. In order to validate the effectiveness of the algorithm and its deployment in real infrastructure, it has been tested in an experimental setup with PV emulators in a set of 5-day tests. Volt-VAr control algorithm successfully adapted its parameters based on grid topology and PV inverter characteristics, achieving a voltage reduction up to 25% of the allowed voltage deviation.

This paper proposes a novel model for a PV cell with parameters variance dependency on temperature and irradiance included. The model relies on commercial available data, calculates the cell parameters for standard conditions and then extrapolates them for the whole operating range. An up-to-date review of the PV modeling is also included with series and parallel parasitic resistance values and dependencies discussed. The parameters variance is analyzed and included in the proposed PV model, where the self-heating phenomenon is also considered. Each parameter variance is compared to the results from different authors. The model includes only standard components and can be run on any SPICE-based simulator. Unlike other approaches that consider the internal temperature as a parameter, our proposal relies on air temperature as an input and computes the actual internal temperature accordingly. Finally, the model is validated via experiments and comparisons to similar approaches are provided.

Integration of battery energy storage in photovoltaic (PV) systems can reduce the electricity costs and provide desirable flexibility and reliability to these systems decreasing renewable energy fluctuations. This paper presents a review of the PV-battery application in Brazil, highlighting the challenges and prospects based on the state-of-art. A PV-battery systems description is presented in this work, as well as the most applied battery technology and its comparison. The paper also describes the set of applications such as voltage and frequency regulation, renewable energy integration, power quality, etc. In the Brazilian scenario, there are applications of PV-battery systems, most of them part of research and development projects (R&amp;D’s), and some real cases are shown, including its goals, applied equipment, operation modes, strategies, and perspectives. Additionally, this work evaluates the Brazilian scenario regarding the energy storage systems implementation challenges, such as regulatory barriers, business models, and opportunities for R&amp;D in the energy market. In conclusion, it is need develop proper regulatory models to expand PV-battery systems and make them visible to the agents in the electricity sector.

Due to the high solar irradiance or energy price, certain regions in the U.S. may reach 100% PV penetration and experience degradation of frequency response greater than the interconnection as a whole. Therefore, in this section, the 100% PV penetration region in each interconnection is simulated to study the local high PV penetration effects. The study was performed by quantifying RoCoF, frequency nadir, and settling frequency at different regional PV penetration levels. The impact of high regional PV penetration on the compliance of grid code on frequency response is also studied.

Despite its growing importance as a dry beneficiation method, there is a lack of studies exploring the fundamentals aspects of dry jigging. In this sense, this study focuses on explore some essential aspects of density-based separation in dry jigs, like pulse profile, energy consumption and, especially, stratification over time, also exploring an innovative operational strategy here called “transient pulsation”. The tests were carried out using density tracers distributed across 11 density ranges (0.4-2.4 g/cm³) and employing a base bed (gravel) to analyze their segregation in a pilot-scale dry jig. Pressure drop and active power data were acquired to measure the pulse characteristics and energy consumption. The findings suggest that establishing the dry jigging cycle is more complex than in hydraulic jigs due to the compressibility of air. Stationary pulsation tests revealed an unstable behavior of stratification over time, contrasting with traditional hydraulic jigs, while transient pulsation tests unveiled varied trends in separation quality. Energy consumption analysis underscored the significant role of the blower drive. These insights have the potential to inform operational enhancements in dry jigging.

The solar energy can mitigate the power supply shortage in remote regions for portable irrigation systems. The accurate prediction of solar irradiance is crucial for determining the quantity of solar panels and the power capacity of photovoltaic power generation (PVPG) systems for mobile sprinkler machines. In this study, a prediction method is proposed to forecast the solar irradiance of typical irrigation areas. The impact of the meteorological parameters on the solar irradiance is studied, and four different parameter combinations are formed and considered as input to the prediction model. Based on meteorological data provided by ten typical radiation stations uniformly distributed nationwide, an Extreme Gradient Boosting (XGBoost) model optimized using the Whale Optimization Algorithm (WOA) is developed to predict the solar radiation. The prediction accuracy and stability of the proposed method are then evaluated for different input parameters through training and testing. The differences between the prediction performances of models trained based on single-station data and mixed data from multiple stations are also compared. The obtained results show that the proposed model achieves the highest prediction accuracy when the maximum temperature, minimum temperature, sunshine hours ratio, relative humidity, wind speed, and extraterrestrial radiation are used as the input parameters. The prediction effectiveness is also verified based on measured data. The WOA-XGBoost model has higher prediction accuracy than the XGBoost model, with predicted values falling within acceptable ranges. The model developed using mixed data of multiple stations can be applied for forecasting solar irradiance in different regions. This study provides a foundation for the optimization of the configuration of PVPG systems for mobile sprinkler machines.

As prominent oil producers, the Gulf Cooperation Council (GCC) countries have played a significant role in the global energy market. However, as the world's attention increasingly shifts towards environmental sustainability, understanding the implications of the GCC's economic activities on CO2 emissions becomes indispensable. This research paper investigates the relationship between specific economic indicators and their impact on CO2 emissions in the GCC from 2001 to 2021. The study employs quantile regression, a powerful statistical method that estimates the conditional quantiles of a response variable given a set of predictor variables. The findings reveal several important insights: Financial institution efficiency is significant and negative at a 1% level at the lower (10th) -83537.3 and the higher quantile (90th) -549002.3. The relationship between GDP per capita and CO2 emissions varies across quantiles, highlighting the complexity of the growth-environment nexus. Total patents exhibit a positive and significant relationship with emissions, underscoring the importance of directing innovation towards environmentally sustainable solutions. Renewable energy consumption displays a nuanced relationship with CO2 emissions, with a stronger negative impact observed at higher consumption levels. This underscores the potential of renewable energy to mitigate emissions when integrated at scale. The study's outcomes hold crucial policy implications for the GCC countries as they seek to align economic growth with environmental sustainability. The findings emphasize the importance of fostering financial institution efficiency, promoting green innovation, and expanding renewable energy sources to reduce emissions

The global food system has three recognized challenges: (a)increasing the availability of food consumption, (b) reducing food loss, and (c) reducing food waste. The increasing demand for food consumption, increasing quantity of food loss, and corresponding increase in food waste are resulting in serious health, aesthetic, social, economic, and environmental problems due to a lack of appropriate planning and management. Despite its importance, there is no clear, concise, and comprehensive definition of food consumption, loss, and waste. Generally, food consumption, food loss, and food waste are dealt with separately. This article presents a logically constructed ontological framework of food consumption, loss, and waste. It gives equal importance to all three aspects of global food management. The systematic ontological framework is general, and the analysis can be applied to any country. The framework deconstructs the combinatorial complexity of the problem and explicates the pathways to manage the consumption, loss, and waste. The ontological framework encapsulates 19*8*7*4*5*6 = 25,536 possible components of the challenge. A critical analysis based on available data using the framework will help to develop strategies to deal with the problem. It can help to discover the gaps and to find ways to bridge the gaps. It is novel to conceptualize food consumption, loss, and waste together.

Background: Coffee is the second most popular drink in the worldwide, and it has different components with antioxidant and antitumor properties. The objective of this study was to explore the relationship between coffee consumption and the incidence and mortality of stomach cancer in the main consuming countries. Methods: An observational study was performed. Dataset of coffee consumption was obtained from WorldAtlas, and incidence and mortality rates from GLOBOCAN database. Spearman's rank correlation coefficient was calculated. All statistical analysis were performed using STATA software. Results: A total of 25 countries were included in the study. There was a significant linear correlation between coffee consumption kg per person per year and an estimated age-adjusted incidence (r=0.5984, p=0.0016) and mortality (r=0.5877, p=0.0020). Conclusion: Coffee consumption could potentially have beneficial effects on incidence and mortality by stomach cancer.

Background: Alzheimer’s disease (AD), the most threatening neurodegenerative diseases, is characterized by the loss of memory and language function, an unbalanced perception of space and other cognitive and physical manifestations. Pathology of the AD is characterized by neuronal loss, and the extensive distribution of senile plaques and neurofibrillary tangles (NFTs). The role of environment and the diet in the AD is being studied actively, and nutrition is certainly one of the main factors playing a prominent role in the prevention of neurodegenerative diseases. In this context, the relationship between dementia and wine use/abuse has received increased research interest in recent times, with varying and often conflicting results. Scope and approach: This review aims to critically summarize the most recent studies conducted to clarify the relationship between wine drinking and AD, as well as whether effects are influenced by quantity and/or frequency of drinking. Key findings and Conclusion: Overall, based on the interpretation of various studies, it can be concluded that there is no indication that light to moderate alcohol drinking is detrimental to cognition and dementia, and it is not possible to define whether alcohol could be used as a means to reduce risk of developing AD.

This study delves into the intricate interplay of economic growth components, specifically focusing on Consumption and investment in Saudi Arabia from 2000 to 2022. Employing vector error correction models and cointegration techniques, we analyze the short- and long-term dynamics within the relationship of Consumption, investment, and economic growth. Granger causality analysis is also used to discern these pivotal variables' causal connections. Our empirical analysis reveals a persistent long-term cointegration relationship among the variables, underscoring the enduring nature of their interdependency. Furthermore, our findings highlight Consumption and investment's statistically significant positive impact on economic growth. Notably, the short-term analysis unveils a stable model characterized by an annual adjustment to equilibrium of 100%.Moreover, the Granger causality study demonstrates unidirectional causal linkages between Consumption, investment, and economic growth. These findings hold substantial implications for policy formulation in Saudi Arabia. Policymakers must grasp the ramifications of burgeoning prosperity and evolving private consumption patterns on future environmental outcomes. Achieving sustainable long-term results necessitates equal emphasis on bolstering private Consumption and fostering other facets of economic growth.

Energy consumption modelling is of critical importance for improving energy efficiency in the drive towards sustainable manufacturing. Modern manufacturing processes and machine tools are very complex as they involve interplay of several advanced technologies. Therefore, energy modelling of modern machine tools is a complex multi-disciplinary task. This paper proposes a systematic and practical framework to choose the appropriate modelling approach for a given industrial problem. The framework was validated by applying it to diverse industrial scenarios.

The assessment of Photovoltaic (PV) systems, a key component of sustainable energy solutions, is of paramount importance in the pursuit of a greener future. This abstract provides an overview of environmental assessments associated with PV systems, considering their life cycle, energy production, and ecological impact. The study explores various methodologies and tools employed in the evaluation of PV systems’ environmental performance, addressing issues such as material sourcing, manufacturing, installation, and end-of-life disposal. Additionally, it delves into the trade-offs and challenges in achieving sustainability objectives in the solar energy sector. By critically examining the environmental implications of PV systems, this research contributes to informed decision-making and the sustainable integration of solar power into our energy landscape.

Bifacial PV modules have become the pervasive choice for utility-scale solar photovoltaic (PV) installations. Understanding bifacial PV performance for commercial deployments is, therefore, critically important. Although there have been studies on the modeling of Bifacial PV performance, to the best of our knowledge, the comprehensive integration of racking and mounting geometry for Bifacial PV performance simulation is yet to be reported. In this work, we modeled the racking and mounting geometry for a field-deployed operational PV array. We then applied optical ray-trace simulation to study the impact of those structures on array performance. The study reveals that the support structures have a considerable impact on the rear surface irradiance and overall bifacial PV performance, amounting to as much as 30% shading in certain situations. The work analyzes the impact of installation parameters such as tilt, height, and row spacing on the bifacial PV array’s performance. Thus, a novel holistic approach to studying the sensitivity of various installation parameters’ impact on bifacial PV array performance, with the racking and mounting structure’s geometry integrated, has been demonstrated through the work. This knowledge and its practice enables site-specific design optimization for utility-scale bifacial solar PV arrays and synergistic PV applications such as agrivoltaics and carports, where maximizing power generation is not necessarily the sole objective.

Food production is a complex matter, affecting people’s lives, organizations’ profits, and the well-being of the whole planet and has multifaceted ethical considerations surrounding its production, distribution, and consumption. This paper addresses the pressing need to confront ethical challenges within the food system, encompassing issues such as environmental sustainability, food security, and individual food choices for better oral and systemic health of all individuals around the globe. From agricultural practices to global trade and food waste, ethical implications are addressed across various domains, highlighting the interconnectedness of ethical decision-making in the food industry. Central themes explored include the ethical dimensions of food production methods, the impact of global trade on food ethics, and the role of individuals in making ethically informed food choices. Additionally, the paper dives into the spiritual and physical significance of food, particularly through the lens of oral health as a gateway to holistic well-being. Recognizing the complexity of the food ecosystem, the paper calls for serious interventions in legislation and economics to promote ethical protocols and techniques for sustainability reasons. It emphasizes the importance of ethical considerations in food safety management systems, regulatory frameworks, and quality standards. Moreover, the paper underscores the need for a comprehensive approach to address ethical dilemmas and moral values inherent in the food industry and oral health policies, advocating for the adoption of the precautionary principle and ethical decision-making frameworks. The article aims to serve as a call to action for stakeholders across the food industry and the healthcare sector, to prioritize ethical practices, promote transparency, rearrange economic parameters and work towards a more sustainable and equitable food system for inner and outer oral and systemic health and human sustainability for all.

Building integrated photovoltaics (BIPV) consists of PV panels that are integrated into the building as part of the construction. This technology has advantages such as the production of electricity without necessary additional land area. This paper provides a literature review about the recent developments in urban building energy modelling, including tools and methods, and how they can be used to predict the effect of PV systems on building outdoor and indoor environments. It is also intended to provide a critical analysis on how PV systems affect the urban environment, both from an energy and a comfort point of view. The microclimate, namelly the urban heat island concept, is introduced and related with the existence of PV systems. It is concluded that urban building energy modelling (UBEM) can be effective to study the performance of PV systems in the urban environment. It allows to simultaneously predict the building energy performance and the microclimate effect. However, there is a need to develop new methodologies to overcome the challenges associated to UBEM, especially in what concerns non-geometric data, which leads to a major source of errors. and to find an effective method to predict the effect of PV systems in the urban environment.

Swarm electrification-driven communities face significant challenges, including implementing advanced distributed control in areas with limited ICT access and establishing trust among villagers hesitant to grant access to their assets. This paper proposes a distributed DC microgrid architecture for P2P energy exchange in these communities, ensuring stability and effective exchange operation. By implementing a Blockchain marketplace specifically designed to suit the rural context, the proposed architecture ensures tracing of exchange transactions to fairly settle participants. Validation experiments demonstrate its efficacy in achieving peak shaving. It provides 11% of the requester's total demand from the community even while maintaining the constraint of reducing discharge-charge cycles to one per day, thereby preserving battery life. Additionally, the solution reduces prosumer production losses by 16% of the total PV production.

Based on collected power generation data associated with solar irradiance, PV system conversion efficiency and cell temperature, an hourly solar PV power estimation model by a parallel artificial neural network (ANN) and particle swarm optimization (PSO) algorithm is proposed. Weight matrices related to different seasons and geographic areas for estimation power generations have been trained by real measured operation data. The parallel PSO algorithm with heuristic global optimization technique assists the ANN training process to get near optimal solutions precisely. The accuracy and reliability of estimation is audited by actual details of photovoltaic power stations in various regions and scales. The results of estimation model can not only assist the electricity dispatcher to explicitly monitor the trend of solar power generation in different areas, but also coordinate with traditional power plants to meet load demand more accurately. The presented model will bring benefits to power dispatching for larger scales of intermittent and unstable solar power generation.

Nutritional status problems in school-age children are a crucial public health problem worldwide. This research explored the relationships between family factors, food consumption behaviors, and the nutritional status of Muslim school-age children in Thasala District, Nakhon Si Thammarat Province, Thailand. This descriptive research was conducted among 228 children aged 9-12 years. Data were collected using demographic data, nutritional status, and food consumption behaviors assessment. Data were analyzed using descriptive, chi-square, and binary logistic regression statistics. The results revealed that most samples reported having moderately healthy food consumption behaviors (M = 2.01, SD = 0.56). The samples had a normal weight (72.4%), while 15.8% were classified as overweight and obese. The number of siblings and food consumption behaviors had a significant relationship with nutritional status (p &lt; 0.05). Confirmation with binary logistic regression results also revealed that the likelihood of normal nutritional status was 2.40 times higher in children who had 3 or 4 siblings compared to those with 1 or 2 siblings (AOR = 2.40; 95% CI: 1.299-4.459). Additionally, children with healthy food consumption behaviors were 2.34 times more likely to have normal nutritional status compared to those with unhealthy dietary consumption (AOR = 2.34; 95% CI: 1.183-4.631). Conclusion: Since the number of siblings and healthy food consumption behaviors were associated with nutritional status, healthcare providers must consider these 2 factors when establishing health education and behavior modification care plans to promote healthy food consumption and nutritional status among this group.

This paper studied the solar PV frequency control in the U.S. Eastern Interconnection (EI) and Texas Interconnection (ERCOT) systems. The studied frequency control approaches include droop frequency control, inertia control, and droop-inertia-combined frequency control. The control effects of different frequency controls of PV in the EI and ERCOT are studied using actual high PV penetration interconnection grid models to provide suggestions to the future revision of future PV frequency control standards.

In this paper, an extensive study on the operation, control and performance of a hybrid photovoltaic and wind turbine (PV-WT) system is presented. The study includes the operation of the hybrid systems under different weather conditions which are reflected on a change in the wind speed and irradiance. Various loading conditions are investigated such a change in active and reactive power demands for static and dynamic loads. The performance of the hybrid system is examined via MATLAB/SIMULINK simulations.

Efficient implementation of clean energy technologies, including pioneering solutions like mobile solar PV systems mounted on trailers (MSPT), is pivotal for addressing energy challenges, especially in regions with constrained power grid access. This endeavour is vital for meeting escalating elec-tricity demands and aligning with the UN Sustainable Development Goal (SDG) aimed at ensuring dependable and sustainable energy provision in developing countries. This paper investigates the aerodynamic behaviour of a designed MSPT using numerical and experimental approaches. Spe-cifically, the study focuses on the effects of wind velocity and tilt angels on the drag and lift forces, as well as drag and lift coefficients on the panel used in the MSPT system. Additionally, the overall wind force acting on the entire MSPT (including 9 large solar PV panels) was examined, considering the combined effects of wind flow and the system's geometry. The simulations were conducted using ANSYS-Fluent software and experimental testing was performed utilizing scaled-down models to validate the accuracy of the simulation. The insights and the knowledge from this study can be utilized to optimize the design, installation, and operation of such systems, ultimately enhancing their performance, reliability, and paving ways for further improvements in mobile solar PV technology.

In this paper a novel and flexible solution for fault prediction based on data collected from Supervisory Control and Data Acquisition (SCADA) system is presented. Generic fault/status prediction is offered by means of a data driven approach based on a self-organizing map (SOM)and the definition of an original Key Performance Indicator (KPI). The model has been assessed on a park of three photovoltaic (PV) plants with installed capacity up to 10 MW, and on more than sixty inverter modules of three different technology brands. The results indicate that the proposed method is effective in predicting incipient generic faults in average up to 7 days in advance with true positives rate up to 95%. The model is easily deployable for on-line monitoring of anomalies on new PV plants and technologies, requiring only the availability of historical SCADA data, fault taxonomy and inverter electrical datasheet.

One of the most crucial and economically beneficial tasks for energy customer is peak load curtailment. On account of the fast response of renewable energy resources (RERs) such as photovoltaic (PV) units and battery energy storage system (BESS), this task is closer to be efficiently implemented. Depends on the customer peak load demand and energy characteristics, the feasibility of this strategy may warry. When adaptive neuro-fuzzy inference system (ANFIS) is exploited for forecasting, it can provide many benefits to address the above-mentioned issues and facilitate its easy implementation, with short calculating time and re-trainability. This paper introduces a data driven forecasting method based on fuzzy logic for optimized peak load reduction. First, the amount of energy generated by PV is forecasted using ANFIS which conducts output trend, and then, the BESS capacity is calculated according to the forecasted results. The trend of the load power is then decomposed in Cartesian plane into two parts, left and right from load peak, searching for BESS capacity equal. Network switching sequence over consumption is provided by a fuzzy logic controller (FLC) with respect to BESS capacity and PV energy output. Finally, to prove the effectiveness of the proposed ANFIS-based peak shaving method, offline digital time-domain simulations have been performed on a real-life practical test micro grid system in MATLAB/Simulink environment and the results have been experimentally verified by testing on a practical micro grid system with real-life data obtained from smart meter and also, compared with several previously-reported methods.

Nuclear energy, along with renewable and alternative energy sources, is a crucial green energy source. However, the existing literature often overlooks the role of nuclear energy in achieving sustainable development goals. This study analyzes the impact of green technological innovation, nuclear energy consumption, and trade openness on environmental quality in the US, which consumed the most nuclear energy from 1990 to 2019. The ARDL bounds testing approach was applied for its effectiveness in smaller samples, suitable for the data set used in this study, to determine cointegration relationships. Additionally, the Toda-Yamamoto causality test was employed to explore causal links without requiring series stationarity or cointegration. The ARDL cointegration results indicate a significant long-term relationship between CO2 emissions, green technological innovation, nuclear energy consumption, and trade openness. The results suggest that promoting green technological innovation and nuclear energy (although this effect is less certain) can be effective strategies for reducing CO2 emissions, while the impact of trade openness requires careful consideration due to its potential to increase emissions. Green technological innovation has a significant unidirectional causal effect on CO2 emissions. These results will help policymakers design policies to achieve sustainable environmental goals in the US economy.

Outbreaks of the crown-of-thorns seastar (CoTS) represent a major cause of coral loss on the Great Barrier Reef. Outbreaks might be explained by enhanced larval survival supported by higher phytoplankton availability after flood events, yet little is known about CoTS larvae feeding behaviour, in particular their potential for selective feeding. Here, single- and mixed-species feeding experiments were conducted on CoTS bipinnaria larvae using five algae (Phaeodactylum tricornutum, Pavlova lutheri, Tisochrysis lutea , Dunaliella sp. and Chaetoceros sp.) and two algal concentrations (1000 and 2500 algae mL^-1). Cell counts using flow-cytometry at the beginning and end of each incubation experiment allowed us to calculate the filtration and ingestion rates of each species by CoTS larvae. In line with previous studies, CoTS larvae ingested more algae when initial algal concentration was higher. We found evidence for the selective ingestion of some species (Chaetoceros sp., Dunaliella sp.) over others (P. lutheri, P. tricornutum). The preferred algal species had the highest energy content, suggesting that CoTS selectively ingested the most energetic algae. Ultimately, combining these results with spatio-temporal patterns in phytoplankton communities will help elucidate the role of larval feeding behaviour in determining the frequency and magnitude of CoTS outbreaks.

We investigate the performance of a novel flat photovoltaic-thermal (PV-T) module under high-vacuum through a 1D numerical model based on steady-state energy balance, with the aims of optimizing the simultaneous production of thermal and electrical energy. In the proposed design, the photovoltaic (PV) cell is positioned directly above the selective solar absorber (SSA), in a multilayer or fully integrated PV-SSA structure, which allows full exploitation of spectral solar radiation. In fact, in this configuration the losses related to non-absorption of low-energy photons and thermalization, typical of a classical single-junction PV cell, are reduced. The present study is conducted as the emittance and energy bandgap of the PV layer varied, thus admitting a wide variety of materials into the analysis. The dependence of the temperature coefficient, β(%/K), on the energy bandgap of the PV cell is also included. In the last part of the work, we discuss the performance of the proposed evacuated PV-T equipped with a SSA layer and thin film solar cells, namely those made of CdTe, CdS and GaAs. Overall, the paper highlights the great advantage of using high vacuum insulation, which suppresses conductive losses, and the versatility of the proposed system, which could be adapted to the user's needs simply by choosing the appropriate material for the photovoltaic layer.

Around 14% of the global population does not have access to electricity. About 95% of those are living in rural Sub-Saharan Africa. Often in these regions, diesel generators are the only source of electricity. The operating cost of these diesel generators is high. However, solar and wind energy are available in most of African countries. This study presents the analysis of designing an off-grid hybrid system with a wind turbine, PV, diesel generator, and battery to power a hospital, school, and 200 household village in four locations across Somalia. The research investigated the availability of wind-solar resources in selected locations. Designing of the system and economic-technical calculations were performed using HOMER. The selection of the optimum design was based on the Cost of Electricity and Net Present Cost. The results show that for Kabaal and Ceel Buur, a WT-PV-DG-Battery is the optimal system as the wind resource in these regions is high. For Saakov and Baki, a PV-DG-Battery system proves to be optimum as the wind resource is limited here. The study also evaluated the control strategy and proved that combined dispatch was the most cost-effective for these locations. The study concluded that hybrid systems are more economical than diesel systems.

This article proposes a new photovoltaic (PV) solar tracker design based on the advantage that installation latitude offers according to efficiency in function of orientation (EFO) of PVs. First, is described a methodology to let incorporate a low-precision, low-cost and high-availability solar tracking mechanism and control system. The design methodology considers the installation location (latitude and azimuth) as a starting point for establishing an adequate angular range of EFO, simultaneity the aspects of available technology and the knowledge accords to developer. Finally, the design technique is experimentally validated by the implementation of a solar tracker at latitude of 28° longitude of 109° and evaluates the efficiency on a specific day. According to result the feasibility of this type of solar tracker for latitudes close to or greater than 30° is highlighted, given that this tracking system costs 30% less than traditional commercial systems as slew drive with its incorporation of lower-resolution azimuth tracking mechanisms. It also increases collection efficiency by 26%, just as continuous or time-based dual-axis solar trackers do, without the more complex controls and mechanisms of these designs.

Corn is the main agricultural product and has been produced in Kazakhstan as important nutrition in human and animal food. The research results shown in the article, the fact of increasing the sustainability of corn production is formulated, methodological approaches to assessing the level of sustainability are developed, and criteria are defined for the main indicators of sustainability and efficiency of corn production. The world's corn production was 1,223 million tons in the 2021/22 season. Kazakhstan's corn production average was 1,1 million tons and the production area are 206,870 in the 2021/22 season. The yield per hectare was 5,985 kg in the 2021/22 season. Corn consumption was 1170.5 million tons and exported was 180.1 m.tons of corn in the 2021/22 season in Kazakhstan. The purpose of this study is a determination of sustainable developments of corn consumption and production in Kazakhstan and worldwide between the 2011/12 and 2021/22 seasons. Statistical data have been obtained from the International Grain Council, FAOSTAT, USDA, PhD diploma thesis of the article's author, Bureau of National Statistics. Data obtained have been shown in the tables issued by the use of percentage and index calculations. The study analyzed a major factor affecting supply and demand, sustainable development of corn production and market prices.

Photovoltaic(PV) power generation is highly nonlinear and stochastic. Accurate prediction of PV power generation plays a crucial role in grid connection as well as the operation and scheduling of power plants. To predict the PV power combination model, this paper suggests a method based on Empirical Mode Decomposition (EMD), Ensemble Empirical Mode Decomposition (EEMD), Complete Ensemble Empirical Mode Decomposition with Adaptive Noise (CEEMDAN), Nonlinear Auto-Regressive Neural Networks with Exogenous Input (NARXNN), Long Short Term Memory (LSTM) Neural Network, and Light Gradient Boosting Machine (LightGBM) algorithms. To attempt to reduce the non-smoothness of PV power, the weather variable features with the greatest effect on PV power are first identified by correlation analysis. Following this, the PV power modal decomposition is split and reorganized into a new feature matrix. Finally， a NARX is used to obtain preliminary PV power components and residual vector features， and the PV power is predicted by combining three models of LightGBM， LSTM, and NARX and then the final prediction results are obtained by combining the PV power prediction results using error inverse method weighted optimization. The prediction results demonstrate that the model put forth in this paper outperforms those of other models and validate the model's validity by utilizing real measurement data from Andre Agassi College in the United States.

This article analyzes laws, normative reforms and regulations surrounding the practices and mechanisms of control over the consumption, cultivation and commercialization of cannabis. On the one hand, I investigate regulatory practices that deny rights for the consumption of cannabis classified as recreational. On the other hand, I study regulatory practices that extend rights for the production, consumption and commercialization of cannabis classified as medicinal and industrial. The empirical moment is composed of four stages and methodological tools. First, I conduct an analysis of state policies. Then, I analyze nine laws and codes on cannabis regulation from 1970 to the present. Next, I perform five semi-structured interviews. Finally, I develop two life stories of former people deprived of their liberty for cannabis cultivation and trade. In this way, I trace forms of regulation on multiple demands, knowledge, interests and beliefs. This research focuses on state regulation. Cannabis regulatory regimes are conceived as constructions of political, social and economic truths, meanings and rights. In sum, the answer to the question of how collective demands around cannabis are regulated in Ecuador stipulates that state action reinforces stigmatization and criminalization. In addition, it legitimizes moral entrepreneurs and counter-movements around cannabis.

This paper analyzes calorie consumption in Vietnam using the household survey data. The data suggest that food insecurity is still a major problem in Vietnam, with nearly 40 percent of the population being unable to meet their calorie requirement. Employing nonparametric and parametric estimation techniques, the paper examines the relationship between household calorie consumption and per capita household expenditure in Vietnam. The analysis indicates a positive and significant relationship between per capita expenditure and per capita calorie consumption. The mean calorie elasticity is estimated to be between 0.21 and 0.31 by the parametric method and 0.20 by non-parametric method. In addition, simulated income and food price changes indicate that undernutrition is very responsive to changes in income and food prices

Background: Public misconception and demand for the indication of antibiotics could lead to inappropriate prescribing and consumption. Successful treatment can only be achieved when the public and industrial users have knowledge on antibiotic use and resistance. This survey is aimed to assess antibiotic usage and knowledge regarding antibiotics and antimicrobial resistance (AMR) among undergraduate students of Universiti Brunei Darussalam (UBD), public university located in Brunei Darussalam. Methods: A cross-sectional study was performed using a self-administered questionnaire. The questionnaire was adapted from the World Health Organization (WHO) Antibiotic Resistance, Multi-country public awareness survey distributed online. Students at UBD were invited to participate in the online survey through internal email. The questionnaire consisted of 5 sections: demographic information, antibiotic usage, knowledge on antibiotics, antibiotic resistance (AMR) and use of antibiotics in agriculture. Data were analyzed descriptively and appropriate inferential statistics was used accordingly. Cronbach’s alpha was also done to determine the internal consistency. The section on antibiotic use and knowledge showed good internal consistency of Cronbach’s alpha 0.66 and 0.86 respectively. Research ethics approval was obtained from the PAPRSB Institute of Health Sciences, Universiti Brunei Darussalam (UBD). Results: A total of 145 students returned the complete questionnaire. The result of the study found that 50% of the students had good level of knowledge of antibiotic and antimicrobial resistance with a mean total knowledge score of 11.4 out of 14. Respondents reported the use of antibiotic in the past (69%). Many of the students could identify the use of antibiotics for the treatment of bacterial infection. However, there were also students who incorrectly thought that antibiotics can be used for cold and flu (43%) and fever (41%). Moreover, 76% of the respondents mistakenly believed that antibiotic resistance is the result of the body becoming resistant to antibiotics. Only 12% of the respondents were found to have poor knowledge in the study. Conclusions: Misconceptions in regards to the use of antibiotics for conditions related to viral illnesses was noticed among the respondents in our study. Thus, improving knowledge on antibiotics is crucial to address those beliefs.

This paper based on systems - theoretic approach to the definition of a country's GDP as not directly observable characteristic of system state. Leontief dynamic model is generalized to take into account the stimulating effect of consumption on GDP growth. In consumption, apart from final consumption, terms are considered: balance of foreign trade, fictitious investments and hidden costs. The Kalman filter uses Rosstat's gross output (for system output) and final consumption (for system control) data from 1995 to 2015. It is concluded that if in the years 2014, 2015 it was possible to increase consumption by 5% by, say, price cuts or some increase in money supply, then GDP would be greater by about 2.5%. GDP real values in recent years are most likely greater than official values. Fictitious investments and hidden costs are found in the amount of up to third the value of final consumption. The accuracy of one-year forecasts of true GDP by the methodology of this article is approximately 1.5%.

Abstract: This article reports the results of an ecological study of cancer incidence rates by state in the US for the period 2016-2020. The goals of this study were to determine the extent to which solar UVB doses still reduced cancer risk compared to findings reported in 2006 for cancer mortality rates for the periods 1950–1969 and 1970-1794 as well as cancer incidence rates for the period 1998–2002 and to determine which factors were recently associated with cancer risk. The cancer data for non-Hispanic white (European American) men and women were obtained from the Centers for Disease Control and Prevention. Indices were obtained for solar UVB at the surface for July 1992, and alcohol consumption, and diabetes and obesity prevalence near the 2016–2020 period. Lung cancer incidence rates were also used in the analyses as a surrogate for smoking, diet, and air pollution. The cancers for which solar UVB is significantly associated with reduced incidence are bladder, brain (males), breast, corpus uteri, esophageal, gastric, non-Hodgkin’s lymphoma, pancreatic, and renal cancer. Lung cancer was significantly associated with colorectal, laryngeal, and renal cancer. Diabetes was also significantly associated with breast, liver, and lung cancer. Obesity prevalence was significantly associated with breast, colorectal and renal cancer. Alcohol consumption was associated with bladder and esophageal cancer. Thus diet has become a very important driver of cancer incidence rates. The role of solar UVB in reducing risk of cancer has been reduced due to people spending less time outdoors, wearing sunscreen that blocks UVB but not UVA radiation, and population increases in overweight and obesity, which lowers 25-hydroxyvitamin D concentrations and generates systemic inflammation, a risk factor for cancer. The dietary approach that would reduce the risk of diabetes, obesity, lung cancer, and, therefore cancer, would be one based mostly on whole-plants and restrictions on red and processed meats and ultraprocessed foods. Solar UVB exposure for a few minutes before applying sunscreen and taking vitamin D supplements would also help reduce risk of cancer.Keywords: alcohol consumption; cancer incidence;

As a result of increased energy consumption, global trade has surged, and serious environmental problems have arisen. The problem is made more complicated by the fact that either environmental damage or economic advancement cannot be compromised. The elements contributing to environmental contamination must be identified and dealt with accordingly if we are to have a healthier future. In this study, what causes CO₂ emissions in Malaysia are examined using the Autoregressive distributed lag (ARDL) model using time series data from 1995 to 2020. The paper also examines the impact of energy use and economic complexity on CO2 emissions. Firstly, it is noted that the Environmental Kuznets Curve (EKC) theory holds in Malaysia. Furthermore, energy consumption has a detrimental impact on reducing CO2 emissions. Furthermore, it has been noted that a greater degree of economic complexity leads to an elevated amount of CO2 emissions over an extended period. The findings suggest significant environmental policy implications for reducing CO2 emissions in Malaysia.

This study aims to provide empirical evidence on whether using renewable and non-renewable energy, CO₂ emissions and the resulting changes in temperature and precipitation can alter cereal yields in European Union countries. To this end, a panel data set covering 1992-2021 has been used to analyse the impact of climate change and economic factors on cereal production in European Union countries. The study employed various analytical techniques to understand better the relationship between climate change, energy consumption, and economic growth. These included using annual average temperature and rainfall to measure climate change and energy consumption and economic growth to analyse the economic aspects. To achieve the objective, feasible generalised least squares (FGLS) models with robust standard errors and bootstrap and a quantile regression (QR) model with marginal analysis were employed. The Westerlund cointegration test confirmed the presence of cointegration between cereal production and climate variables, economic growth, and energy consumption. The results indicate that increases in temperature and precipitation may contribute to increased cereal production in European Union countries. In contrast, energy consumption, including renewable energy and CO₂ emissions, may have a nonlinear effect on cereal production. Quantile regression analysis suggests climate change may impact crop yields most in countries with low and moderate cereal production per hectare. Increased CO₂ emissions may increase yields in the initial period, but excessive CO₂ may negatively impact cereal production in the long term. It would be advisable for countries with low and moderate crop productivity to consider implementing technological advances and combating global warming by modernising cultivation methods and making greater use of renewable energy sources.

Abstract: Like other plants, every PV power plant will one day reach the end of its service life. Calculations show that 20,400 tons of PV waste will be generated worldwide by 2030 and 60.2 million tons by 2050, not including the mass of the support structure. Such large amounts of waste pose a potential threat to the environment and people if not properly managed. The paper analysed the options for dealing with PV waste, namely reuse, recycling and landfilling. For recycling as the best option in terms of environmental protection and circular economy, an overview of recycling technologies and the percentage of achievable recycling for the materials contained in each PV system component is given. In addition, the current situation of legislation and recycling of PV modules in Europe was examined with special reference to the Balkan countries. There are a small number of factories for recycling PV modules in Europe, but none in the Balkan countries. The main reason for this is the small amount of PV waste in these countries and consequently the economic unprofitability. For this reason, PV modules (after dismantling the aluminum frame and cables) are mostly disposed of as non-hazardous waste in landfills in these countries. Finally, the main barriers to faster implementation of PV module reuse and recycling are listed, along with guidelines for their removal. The cost of recycling Si modules is about ten times higher than the cost of disposal. To change this ratio in favor of recycling, cheaper recycling methods need to be developed and taxes on landfill disposal need to be increased.

Pancreatic cancer is one of the most fatal common cancers affecting both men and women, representing about 3 percent of all new cancer cases in the United States. In this study, we aimed to investigate the association of pancreatic cancer risk with alcohol consumption as well as folate intake. We performed a case-control study of 384 patients diagnosed with pancreatic cancer from May 2004 to December 2009 and 983 primary care healthy controls. Our findings showed no significant association between risk of pancreatic cancer and either overall alcohol consumption or type of alcohol consumed (drinks/day). Our study showed dietary folate intake was modestly but significantly inversely associated with pancreatic cancer (OR=0.99, P <.0001). The current study supports the hypothesis that pancreatic cancer risk is reduced with higher food-based folate intake.

This study proposes a short- and medium-term electricity consumption prediction algorithm by combining the GRU model suitable for long-term forecasting and the Prophet model suitable for seasonality and event handling. (1) Manufacturing Company B's Electricity consumption data and meteorological data in Naju, Jeollanam-do, South Korea are collected and preprocessed. (2) The preprocessed data proposes the Prophet model in the first step for seasonality and event handling prediction. (3) In the second step, seven multivariate data are experimented with GRU. Specifically, the seven multivariate data consist of six meteorological data and the residuals between the predicted data from the proposed Prophet model in Step 1 and the observed data. These are utilized to predict electricity consumption at 15-minute intervals. (4) Electricity consumption is predicted for short-term (2 days and 7 days) and medium-term (15 days and 30 days) scenarios. The experimental results demonstrate that the proposed method outperforms the conventional Prophet model by more than 23 times and the modified GRU model by more than 2 times in terms of MAPE.

Recent years have seen a rapid uptake in distributed energy resources (DER). Such technologies pose a number of challenges to network operators, which can ultimately limit the amount of rooftop solar photovoltaics (PV) systems that can be connected to a network. The objective of this industry-based research was to determine the potential network effects of forecast levels of customer owned rooftop solar PV on Energy Queensland’s distribution network and formulate functions that can be used to determine such effects without the requirement for detailed network modeling and analysis. In this research, many of Energy Queensland’s distribution feeders were modelled using DIgSILENT PowerFactory and analyzed with forecast levels of solar PV and customer load. Python scripts were used to automate this process and quasi dynamic simulation (QDSL) models were used to represent the dynamic volt-watt and volt-var response of inverters, as mandated by the Australian Standard AS/NZS 4777. In analyzing the results, linear regression was used to form trend equations that represent various network characteristics against the number of PV connections. The trend equations provide a way of approximating network characteristics for other feeders under various levels of customer owned rooftop solar PV without the need for detail modeling.

The battery energy storage systems (BESS) are most promising solution for increasing efficiency and flexibility of distribution networks (DNs) with significant penetration level of photovoltaic (PV) systems. There are various issues related to the optimal operation of DNs with integrated PV sys-tems and BESS that need to be addressed to maximize DN performance. This paper deals with the day-ahead optimal active-reactive power dispatching in unbalanced DNs with integrated sin-gle-phase PV generation and BESSs. The objectives are the minimization of cost for electricity, en-ergy losses in the DN and voltage unbalance at three-phase load buses by optimal managing of active and reactive power flows. To solve this highly constrained nonlinear optimization problem, a hybrid particle swarm optimization with sigmoid-based acceleration coefficients (PSOS) and cha-otic gravitational search algorithm (CGSA), called PSOS-CGSA algorithm, is proposed. A scenario based approach encompassing the Monte Carlo simulation (MCS) method with the simultaneous backward reduction algorithm is used for the probabilistic assessment of the uncertainty of PV generation and power of loads. The effectiveness of the proposed procedure is evaluated through the series test cases in a modified IEEE 13-bus feeder.

This work deals with the performance evaluation of novel flat photovoltaic-thermal (PV-T) modules under vacuum. Through a 1D (dimensional) steady-state-energy-balance numerical model developed in MATLAB, two different layouts are studied: the first consisting of a photovoltaic (PV) cell installed just below the glass encapsulating the flat panel, and the second where the PV cell is placed on the selective solar absorber (SSA). In both cases the thermal and electrical efficiencies have been evaluated at different SSA operating temperatures, in the range of 323 K to 423 K. The analysis has been conducted at different energy bandgap (E_bg) of the PV cell and assuming a variable transmittance or emittance of the PV cell, depending on the design. The two systems efficiency comparison has been carried out at the same operating temperature. Overall, this work highlights the importance of high vacuum insulation, which guarantees the reduction of convective thermal losses, and shows that the maximum energy is produced for PV cells with E_bg ≈1.5-1.7 eV, depending on layout and operating temperature, by including the thermal output in the PV-T optimization. The energy and exergy efficiencies obtainable using the proposed PV-T systems are considerably improved compared to the results previously reported in the literature.

In this paper, the seven traditional models of PV modules are reviewed comprehensively to find out the appropriate model to be reliable. All the models are validated using the Matlab code and make a graphical comparison. The accuracy and convergence of each model are evaluated using data of manufactured PV panels. Then, a novel model is proposed showing its consistent performance. The most three key parameters of single-diode model are self revised to adapt to various type of PV modules. This new method is verified in three types of PV panels' data measured by National Renewable Energy Laboratory (NREL), US. The validated data show promising results when the error RMSEs' range of the proposed model is under 0.36.

Power semiconductor devices are essential from the operation point of view, size, efficiency and cost, these components are used in a myriad of applications, providing features that make them an important part of the system in which they are operating. This document analyzes and compares the basic structure, properties, design aspects, as well as temperature performance, stability and switching losses, present in devices on silicon (Si), silicon carbide (SiC) and new generation devices fabricated in gallium nitride (GaN) applied in renewable energy systems. The main objective is determinate the viability of the new generation components, which present a superior performance in view of an increase in efficiency, conductivity, decreases in switching losses, lower resistances and parasitic capacitances as well as higher operating frequency range. Therefore demonstrating the GaN components are a strong and viable candidate to solve some of the problems present in renewable energy systems.

This research work deals with the modeling and control of hybrid photovoltaic (PV) - Wind micro-grid using Quasi Z-Source inverter. This inverter provides better buck/boost characteristics, able to regulate the phase angle output, less harmonic content, no requirement of the filter and has high power performance characteristics over conventional inverter as major benefits. A SEPIC converter as dc-dc switched power apparatus is employed for maximum power point tracking (MPPT) functions which provides high voltage gain throughout the process. Moreover, a modified power ratio variable step (MPRVS) based perturb & observe (P&O) method has been proposed in the PV MPPT action which forces the operating point close to maximum power point (MPP). Practical responses justify the performance of hybrid PV-Wind micro-grid with Quasi Z-Source inverter structure.

The rapid development of China’s textile industry leads to consumption and pollution of large volumes of water. Therefore, the textile industry has been the focus of water conservation and waste reduction in China’s 13th Five-Year Plan (2016–2020). The premise of sustainable development is to achieve decoupling of economic growth from water consumption and wastewater discharge. In this work, changes in blue water (water consumption), grey water (water pollutants), and water footprints of the textile industry from 2001 to 2014 were calculated. The relationship between water footprint and economic growth was then examined using the Tapio decoupling model. Furthermore, factors influencing water footprint were determined through logarithmic mean Divisia index (LMDI) method. Results show that the water footprint of China’s textile industry has strongly decoupled for five years (2002, 2006, 2008, 2011, and 2013) and weakly decoupled for four years (2002, 2007, 2009, and 2010). A decoupling trend occurred during 2001–2014, but a steady stage of decoupling has not been achieved yet. Based on the decomposition analysis, the total water footprint is mainly increased by production scale and inhibited by the technology. In addition, the effect of industrial structure adjustment is relatively weak.

Among young children, parents are a main factor of children's preferences for food served as they are responsible for purchasing and providing Functional Foods (FFs) and they are role models for them. This revies study conducted according PRISMA guidelines and aimed to review the recent data about the consumption of FC into families as part of a balanced diet. The literature search was conducted via online academic search engines PubMed, ResearchGate and Google Scholar. The search process was restricted to research papers published in English in reviewed journals from 2012 to 2023. Thirty six articles were ultimately included in the present review. The results showed that there is a correlation between several socio-demographic and a higher probability of buying FFs for children. There is a positive effect on purchasing frequencies of gender (female), higher household annual income and education level, together with higher levels of nutritional knowledge and trust in positive scientific evidence regarding FFs. Also, parents’ socio-demographic factors affect the children’s F/V consumption. The summary of evidence concludes on the point that parents are the role models about their children’s eating behavior and eating habits.

Institutional sustainability is a dynamic and multifaceted concept that relies on the contributions of various institutions, including the legal and the scientific system. On the other side, consumers boycotts are an expression of political consumerism by which consumers can use their market power to attain sustainability objectives. This article explores institutional trust on the legal system and trust on scientists as potential drivers for consumers’ boycotts. Using data retrieved from the European Social Survey covering twenty-five countries, the study employs binary logistic regression to assess the importance of institutional trust and other potential drivers of product boycotts in Europe. Results confirm that boycotting behaviour is affected by institutional trust, as well as other individual variables including gender, age and life-cycle effects, education, interest in politics and level of satisfaction with the political system, generalized trust, personal well-being, and consumers’ use and perceptions of information and communication technologies. The results of this study enrich the literature on consumer boycotts and have implications for policymakers involved in sustainability initiatives.

This study has investigated the effect of nutrition labeling on consumer guilt, in situations where consumers ingest products that have an unhealthy image. The first investigation has examined the effects of types of nutrition labeling (adding healthy ingredients/reducing unhealthy ingredients). The second investigation has examined the influence of two goal-activation types(utilitarian and hedonic) and nutrition labeling on consumer guilt. The findings reveal that the utilitarian-goal-activation group felt less guilty about consuming a product with a reduced unhealthy ingredient than they did about consuming a product with an added healthy ingredient. In addition, there were interactions between the two variables, since consumer goal activation had more effect on consumer guilt about products with reduced unhealthy ingredients than on products with added healthy ingredients. Based on these results, the academic and practical implications of the present study are discussed. and proposes several directions for future research.

The objective of this study was to investigate the relationship between coffee consumption and obesity in Korean women. We included 5,995 women who participated in a health screening examination at the Korean National Cancer Center between 2007 and 2016. Daily coffee consumption was evaluated using the food frequency questionnaire. Obesity was assessed by body mass index (BMI), and abdominal obesity was assessed by waist circumference (WC). A multiple logistic regression model was used to calculate the odds ratio (OR) of obesity according to coffee consumption. After multivariate adjustment, high coffee consumption was positively associated with obesity measured by BMI (≥ 3 cups vs. no drinks, OR = 2.52; 95% confidence interval (CI) = 1.91-3.34; P for the trend < 0.001) and abdominal obesity measured by WC (≥ 3 cups vs. no drinks, OR = 2.11; 95% CI = 1.59-2.79; P for the trend < 0.001). The positive association between daily coffee consumption and obesity prevalence was not altered by menopause. The amount of coffee consumed per day by Korean women was positively correlated with the prevalence of obesity, but the mechanism underlying this phenomenon remains to be elucidated.

This article analyzes and compares the integration of two different maximum power point tracking (MPPT) control methods, which are tested under partial shading and fast ramp conditions. These MPPT methods are designed by Improved Particle Swarm Optimization (IPSO) and a combination technique between Neural Network and Perturb & Observe method (NN_P&O). These two methods are implemented and simulated for photovoltaic systems (PV), where various system responses, such as: voltage and power are obtained. The MPPT techniques were simulated using Matlab/Simulink environment. A comparison of the performance of IPSO and NN_P&O algorithms is carried out to confirm the best accomplishment of the two methods in terms of speed, accuracy and simplicity.

There are ~200.000 households living in the detached houses and ger (yurt) with the small-coal stove which burns a raw coal in the Ulaanbaatar city. The proper heating system and improvement on the energy efficiency of residential dwellings is vital important for Ulaanbaatar city to reduce an air pollution as well as for the operation of current central energy system. This study shows the experimental results of two Gers with two different heating system and different thermal insulation. Technical availability of the system consisting of ETS heater with daytime charging schedule and areal PV system is also examined by using a simulation of MATLAB programming. As a result of the experiment, the indoor comfort level and energy efficiency of the Ger with added insulation and ETS heater with nighttime charging was enhanced to compare with the reference Ger. The Ger with added insulation and ETS heater consumed 3169 kWh for electric appliances and 5989 kWh for the heating season. The simulation was resulted that the ETS heater to be installed in the Ger 2 had prospected to increase the PV self-consumption rate by 76% because of the daytime charging schedule of ETS heater. The PV system supplied 31% of the total energy consumption with remained 69% of the main grid.

With a high proportion of distributed photovoltaic and lower fossil energy integrated into the distribution network, it is very difficult to ensure the reliability of power supply. The distributed photovoltaic planning model based on big data is proposed. According to the impact stochastic photovoltaics and loads on reliability planning, the static and dynamic capacity-load ratios are proposed. The big data analysis model of distributed photovoltaic planning is established. The big data multi-scenario generation and reduction algorithm of stochastic distributed photovoltaic and load planning is studied, and a source-load big data scenario matching model is proposed. Ac-cording to the source load big data scenario, the dynamic capacity-load ratio of the distribution network is obtained. The static capacity-load ratio calculation method in distribution network planning is studied to ensure the reliability of power supply. Finally, the IEEE 33-bus system is used as an example. The results show that distributed photovoltaic planning based on big data and multi-scenario methods can improve photovoltaic utilization and power supply reliability.

This paper focuses on designing and assessing Pumped Hydroelectric Energy Storage Systems (PHES), connected to the grid and PV system for self-consumption structured at Mutah university in an area of high solar potential. In focusing on PHES and PV literature was made to have data on the field, based on the grid code needed in Jordan. Next, a prospection to find the proper location for the installation was done. Afterward, a load profile was inserted to know the energy demand of the university. Then The productivity of the solar power plant of Mutah University was included. Finally, MATLAB software was used to realize the amount of energy to be stored, this data was used to implement the system which was chosen and sized. PHES layout was created to find the most accurate values for parameters to optimize the system performance, and to investigate the loss analysis. The system attains 9230.89 MWh/year. An annual load yields 4430 MWh/year, which covers the Mutah university demand with an estimated saving of 2039773 JD.

The solar heat pump system based on photovoltaic photothermal (PV/T) modules is a new technology that integrates photovoltaics and heat reutilization. It can improve the efficiency of photovoltaic conversion and recovery the remaining heat generated during the photoelectric conversion process, thereby improving the comprehensive efficiency of the whole system. Simulink software is a visual simulation tool, which has the advantages of strong applicability, clear simulation structure and calculation process. The design of its graphical programming greatly simplifies the user modeling process and allows for direct viewing of results, therefore improving the simulation efficiency. At present, there is little research on simulation of solar heat pump systems with PV/T modules based on Simulink software. In this paper, the mathematical models of each component contained in the PV/T solar heat pump system were established based on the system working principle, energy conservation equations and some empirical formulas, and then the operation of the system was simulated by the Simulink software. Due to the operation characteristic of PV/T modules is the key influencing factor for the whole system performance, the model and simulation process for PV/T modules were introduced in detail. The results showed that the surface temperature of PV/T modules under different operating conditions was significantly lower than that of ordinary photovoltaic panels, and the temperature change amplitude was lower. As results, the power generation and photovoltaic conversion efficiency were significantly improved.

This research emphasizes a meta-heuristic Modified Ant Lion Optimizer (MALO) optimization approach for simultaneous utilization of DSTATCOM devices and distributed Photovoltaic (PV) sources with network reconfiguration in a radial power distribution scheme. In a radial power distribution network with network reconfiguration majority of the research is based on Constant Power model analysis. However, it is noticed that load models have a substantial impact on the distributed PV sources and the D-STATCOM device's optimal size and position. The effect of the Constant Power (CP) and Polynomial (ZIP) with load growth load models for the simultaneous insertion of distributed PV sources and DSTATCOM devices with network reconfiguration examined in this research work for power system planning. The penetration levels of distributed PV sources considered for the investigation are 25%, 50%, 75%, and 100%. The principal objective of this research is to reduce network total power losses, enhance the voltage magnitude profile at all buses, and reduce the overall operating cost while adhering to equality and inequality constraints. The proposed algorithm verified on 118-node test systems. The investigation is carried out for planning network upgradation to a High Voltage Distribution System(HVDS) on 317 nodes in the rural Bangalore Electricity Supply Company Limited(BESCOM) radial distribution scheme. Simulated results obtained by this method are validated with the BAT algorithm and available techniques in the literature.

Nearly Zero Energy Buildings (NZEBs) play a key role in the world energy transition and this is motivating the scientific community to develop innovative electrical and thermal systems, characterized by very high efficiency to specifically address the energy needs of modern buildings. Naturally, the integration on buildings of latest generation PV-systems helps to satisfy this need and, having in mind this objective, an innovative and highly efficient BIPV-system is presented and discussed in this paper. First, the proposed PV-system is purpose-built to be fully integrated into a variety of buildings and, preferably, into their rooftop. It is based on a certain number of innovative rotating and bifacial PV-modules which are specifically made to be installed “under-glass”, within a likewise custom-made transparent casing. Each of the aforementioned PV-module has the form of single row of bifacial PV-cells and is equipped with two special terminations; the PV-modules are then installed inside their transparent casing, side by side and suitably spaced from each other. Thanks to the aforementioned properties, the PV-modules can rotate around their central longitudinal axis, by using a very low-power, reliable and efficient mono-axial solar tracking system. Finally, by the aforementioned way, the proposed PV-system assumes – de facto - the form of a transparent BIPV-generator (PV-skylight), equipped with an innovative “under-glass” single axis solar tracking system. Once the proposed PV-generator is fully integrated into a building, it generates electricity and, additionally, helps to improve both the whole energy performances and the aesthetic appearance of the building. The electricity generation and illuminance performances of the proposed BIPV-generator are experimentally tested by using a low-power home-made prototype driven by different solar tracking logics and under different operating conditions; the most relevant results are summarized and extensively discussed.

Accurately predicting the power of solar power generation can greatly reduce the impact of the randomness and volatility of power generation on the stability of the power grid system, which is beneficial for the balanced operation and optimized dispatch of the power grid system, and reduces operating costs. Solar PV power generation depends on weather conditions, which are prone to large fluctuations under different weather conditions. Its power generation is characterized by randomness, volatility and intermittency. Recently, the demand for further investigation and effective use on the uncertainty of short-term solar PV power generation prediction has been getting increasing attention in many application of renewable energy sources. In order to improve the predictive accuracy of output power of solar PV power generation and develop a precise predictive model, the authors worked predictive algorithms for the output power of a solar PV power generation system. Moreover, since short-term solar PV power forecasting is one of the important aspects for optimizing the operation and control of renewable energy systems and electricity markets, this review focuses on the predictive models of solar PV power generation, which can be verified in the daily planning and operation of a smart grid system. In addition, the predictive methods in the reviewed literature are classified according to the input data source used for accurate predictive models, and the case studies and examples proposed are analyzed in detail. The contributions, advantages and disadvantages of the predictive probabilistic methods are compared. Finally, the future studies of short-term solar PV power forecasting is proposed.

The outdoor field test of the 4-terminal on Si tandem photovoltaic module (specifically, InGaP/GaAs on Si) was investigated and performance model, considering spectrum change affected by fluctuation of atmospheric parameters, was developed and validated. The 4-terminal on Si tandem photovoltaic module had about 40 % advantage in seasonal performance loss compared with standard InGaP/GaAs/InGaAs 2-terminal tandem photovoltaic module. This advantage is expanded in (subarctic zone) < (temperate zone) < (subtropical zone). The developed and validated model used all-climate spectrum model and considered fluctuation of atmospheric parameters, and can be applied every type of on-Si tandem solar cells.

Fourteen (14) rack-mounted polycrystalline modules installed on the concrete roof of the solar energy applications laboratory at the Kwame Nkrumah University of Science and Technology (KNUST) in Ghana, a hot humid environment were assessed after 19 years of continuous outdoor expodure. The physical state of the modules was documented using a visual inspection checklist. They were further assessed by current-voltage (I-V) characterization and thermal imaging. The modules were found to be in good physical state, except some bubbles on front side and minor discolouration/corrosion at edge of the cells. Compared with reference values, the performance decline of the modules observed over the exposure period was: nominal power (P_nom), 21% to 35%; short circuit current (I_sc), 5.8% to 11.7%; open circuit voltage (V_oc) 3.6% to 5.6% and 11.9% to 25.7% for fill factor (FF). It is hoped that this study will provide some helpful information to project developers, manufacturers and the research community on the long-term performance of PV modules in Ghana.

With firm commitment to energy labelling, it is not a question of if but only of when the European Union will introduce an energy label for electric cars. To support such policy efforts, we conducted a scoping analysis of energy consumption and efficiency trade-offs for 342 electric car models sold in Europe. The results suggest that certified and real-world energy consumption average 19 ± 4 kWh/100 km and 21 ± 4 kWh/100 km, translating into drive ranges of 440 ± 120 km and 380 ± 110 km, respectively. Energy consumption is correlated with vehicle mass, frontal area, and battery capacity, but less so with rated power and vehicle price. Each 100 kg of vehicle mass and 0.1 m2 of frontal area tend to increase energy consumption by 0.20 ± 0.06 kWh/100 km and 0.72 ± 0.05 kWh/100 km. Raising battery capacity by 10 kWh increases vehicle mass by 145 kg, energy consumption by 0.6 kWh/100 km, and drive range by 45 km. Efficient vehicles are available at any price but drive range has a cost. Our findings point to considerable efficiency trade-offs that could be tapped by a dedicated energy label. We propose several options for categorizing vehicles on an efficiency scale from A to G, with and without additional utility parameters. Our analysis provides rationale for energy labelling of electric cars in Europe and could inspire similar analyses for other vehicle categories such as e-scooters, lightweight three- and four-wheelers, e-busses, e-trucks, and electric non-road machinery.

Building electric energy is characterized by a significant increase of its uses (e.g. vehicle charging), a rapidly declining cost of all related data collection and a proliferation of smart grid concepts, including diverse and flexible electricity pricing schemes. Not surprisingly, an increased number of approaches have been proposed for its modeling and forecasting. In this work, we place our emphasis on three forecasting related issues. First, on the forecasting explainability, i.e. the ability to understand and explain to the user what shapes the forecast. To this extent we rely on concepts and approaches that are inherently explainable, such as the evolutionary approach of genetic programming (GP) and its associated symbolic expressions, as well as the so-called SHAP (SHapley Additive eXplanations) values, which is a well established model agnostic approach for explainability, especially in terms of feature importance. Second, we investigate the impact of the training timeframe on the forecasting accuracy; this is driven by the realization that a fast training would allow for faster deployment of forecasting in real life solutions. And third, we explore the concept of counterfactual analysis on actionable features, i.e. features that the user can really act upon and which therefore present an inherent advantage when it comes to decision support. We have found that SHAP values can provide important insights into the model explainability. As for GP models, we have found comparable and in some cases superior accuracy when compared to its neural-network and time-series counterparts but a rather questionable potential to produce crisp and insightful symbolic expressions, allowing a better insight into the model performance. We have also found, and report here on an important potential especially for practical, decision support, solutions of counterfactuals built on actionable features and short training timeframes.

Dietary intake and alcohol consumption might be influenced by genetic variations in taste receptor genes. The objectives of this study were to examine the relationship between polymorphisms in bitter taste receptor genes TAS2R13 (rs1015443) and TAS2R38 (rs1726866, rs10246939, and rs713598) as well as alcohol consumption and body fat percentage in college students. Four hundred and two students with a mean age of 20.2 years participated in this study. An NIH Diet History Questionnaire (DHQ II) was used to collect data on their dietary intake, while AUDIT survey was used to determine their level of alcohol consumption. Bitter taste receptor gene polymorphisms were assessed by TaqMan allelic discrimination assays. Despite significant associations between TAS2R13 (rs101544) and certain aspects of alcohol consumption, including the frequency of alcohol intake, no indeed significant associations were found between TAS2R13 (rs1015443) and alcohol consumption after accounting for confounding variables in the regression model. Neither association was found regarding percent of body fat. In contrast, ethnicity and gender significantly influenced percent of body fat (p < 0.001), while no significant association was observed between TAS2R13 (rs1015443) and percent of body fat. Likewise, TAS2R38 (rs1726866, rs10246939 and rs713598) demonstrated no significant association with alcohol consumption and percent of body fat. These results were controlled for confounding factors, such as ethnicity and gender. Body fat percentage and alcohol consumption may be influenced by ethnicity, gender and age rather than SNPs of TAS2R13 and TAS2R38 genes. Assessing the taste genes’ interactions with diet and body composition might be useful in identifying human disease risk.

The purpose of the study is to show the effect of the intake of vitamin C obtained from a diet rich in fruit and vegetables or vitamin C supplements on the level of vitamin C in the plasma. The level of vitamin C in plasma were determined before the study (T1), and after five months (T2). Moreover, a medical record was carried out and a questionnaire on the habits such as general eating and specific consumption of food rich in vitamin C. Both of them were completed before and after five months. In addition, related anthropometric analyses were carried out. The results of the first determination of vitamin C level in plasma were between 1.0 and 16.0 mg/L and the results of the second determination of vitamin C in plasma were between 4.9 and 14.1 mg/L. Furthermore, it was identified that 50% of the questioned people had a low fruit intake. Raw vegetables were consumed by fewer people, the intake being higher during the main meals. The correlation of plasma vitamin C with the eating habits of the subjects to the study points out an interdependence between the consumption of fruit and vegetables and the level of vitamin C in the plasma.

The global agricultural sector is increasingly pressured to adopt sustainable practices and reduce its environmental impact. In this context, greenhouses play a crucial role in enabling year-round crop production, ensuring food security, and minimizing reliance on traditional open-field farming. However, the energy consumption associated with greenhouse operations poses a significant challenge to achieving sustainability goals. As a result, there is a growing emphasis on transitioning greenhouses towards near-zero energy consumption. Near-zero energy consumption in greenhouses refers to the ambitious objective of minimizing energy usage to the greatest extent possible while maintaining optimal growing conditions for crops. This goal encompasses reducing energy consumption for heating, cooling, lighting, and other operational needs, as well as exploring renewable energy sources to power greenhouse operations. This review article offers a comprehensive overview of greenhouse energy consumption, with the main goal of analyzing the present situation, identifying key challenges, exploring potential opportunities, and proposing future perspectives for decreasing energy usage in greenhouse environments. As the focus on sustainable agricultural practices grows, the need to reduce energy consumption in greenhouses becomes increasingly important. The review critically examines current technological models and strategies applied in smart greenhouse applications, as well as the monitoring of microclimatic conditions inside the greenhouse, encompassing factors such as temperature, humidity, CO2 levels, soil quality, and crop cultivation. Moreover, it aims to present existing literature that investigates the advancement of greenhouses toward achieving significant reductions in energy consumption.

Although impending urbanization is a well-acknowledged problem, there is a rising concern about how the urban forms will change and what can be the impacts on the global energy demand. As hubs of economic, social and cultural activities, cities are major energy consumers and GHG emissions. Energy consumption is a technical or a spatial problem? From Newman and Kenworthy to today, several studies have tried to shed light on this nexus. In this work, the controversial paradigm of urban density is discussed as a key component of the fight against climate change impacts. Concerning energy consumption, an in-depth bibliometric analysis is developed to identify the interdependencies of the terms. As a key ‘promise’ of an efficient urban configuration, density has been the core of diverse studies but with still under exploration arguments. This work provides a way forward for planners seeking to design strategies related to dense urban tissues exploring controversial paradigms as a key solution for energy-efficient problems.

With the year 2020, the world faced a new threat that affects all areas of life, negatively affects production in all areas, and paralyzes social life. The measures and restrictions taken by the country's governments to prevent the epidemic from spreading rapidly in the society with the effect of the Covid-19 virus, which first appeared in China and spread all over the world, brought a new lifestyle. Covid-19 has been much the impact on electricity use and electricity production in the period in Turkey as in other countries. There was a sharp decline in commercial and industrial electricity use. The coronavirus effect has also been reflected in the electricity demand and the consumption amount has undergone a great negative change. Due to the enactment of measures against the new type of coronavirus (COVID-19) epidemic and the partial or full-time curfews, electricity consumption was moved to homes, supermarkets, and hospitals in April 2020 from places where mass consumption is intense, such as industry, workplaces, and educational institutions. In this study, Covid-19 period, the first cases were examined electricity production and consumption in Turkey as of the date it is seen throughout, in comparison with electricity consumption data in the same month of the previous years corresponding to this period, the effects on electricity generation and consumption habits of this period were examined.

A novel hybrid CSP-PV power plant is presented. Instead of the integration used in current hybrid power plants, where part of the PV production is charged into the thermal energy storage system through electrical resistors, the proposed system integrates both PV and thermal solar fields using a high-temperature heat pump. Both the heat pump and the heat engine are based on Brayton supercritical CO2 thermodynamic cycles. Such integration allows for charging the molten salts storage as if a central tower receiver field supplied the thermal energy, whereas parabolic trough collectors are employed. Unlike conventional hybrid plants, where the storage of PV production leads to a decrease in power injected into the grid throughout the day, the power injected by the proposed system remains constant. The heat engine efficiency is 44.4%, and the COP is 2.32. The LCOE for a 50 MWe plant with up to 12 hours of storage capacity is 171 $/MWh, which is lower than that of existing CSP power plants with comparable performance. Although the cost is higher compared to a PV plant with batteries, this hybrid system offers two significant advantages: it eliminates the consumption of critical raw materials in batteries, and all the electricity produced comes from a synchronous machine.

Due to an increase of the monocrystalline PV systems installations, for a drive towards the sustainable smart cities in the hot arid developing country such as Pakistan, pose challenges of the performance and degradation issues. Monocrystalline PV module efficiencies are declining and damaging under the continuous exposure to higher surface day-time temperatures in the different parts of the country. A MATLAB simulations were performed based on the validated mathematical approach. This paper investigates the hot arid surface temperature impacts on the performance of PV modules during the summer and winter seasons in Pakistan. The investigations are performed examining the power generating efficiency of the PV system. This paper also investigates the influence of installations of PV-system in the North, South, East and West regions of Pakistan. It was examined that the northern areas of Pakistan are more suitable for maintaining the long-term durability of the PV system. Investigations are performed for the peak summer and peak winter days. During summer months, cooling strategies have to be implemented to overcome the heating effects whilst reducing degradation effect on installed PV-system.