The intelligent morphing wing structure has the characteristics of flexibility, large deformation and adaptive change, which are different from those of the conventional wing. The motion law of the variable-camber leading edge is analysed by the numerical simulation method based on kinematics theory to solve the problem of verifying the motion function and structural strength of the variable camber wing. The driving deformation and aerodynamic load simulation of the variable camber leading edge are realised by designing a follow-up load test apparatus. Based on the numerical simulation of the mechanical boundary, the motion trajectory of the upper and lower wing loading points was predicted, and a multi-point cooperative control system was developed. Multi-sensor iteration was used to ensure the loading accuracy of the test control. The test results show that the average error of the deflection angle is 4.59% in the variable camber leading edge motion test. In the variable camber leading edge strength test, the average error of applied load magnitude and direction is 0.54% and 0.24%, respectively.

The Study proposes possible solution to enhance Password Authentication using Association Technique based on the Ecological theory of memory and data at the Presbyterian university College Ghana. The study used a deductive research approach and employed two empirical Studies using the non-probability sampling technique where few respondents were selected in categories out of the populace by means of openness in other to get similar categories of respondents with different age groups and education background. The two Empirical study also used a quasi-experimental approach which structure incorporate observation, experimental treatment and timing. The First empirical study carried out an investigation to identify existing Password authentication Technique used by End Users, as well as their behavior in password utilization through a self-completed questionnaires which was analyzed using SPSS version 21 . The Second empirical study was an experiment to compared three kinds of password constructions that is own set, modified dictionary, and association against one another to see which of them would be best meet the ecological theory of memory and data which aims at creating a secured password that is easy to recall. The computation and evaluation of password construction was done using My1login Password meter whiles Levenshtein Distance String Edit Software was also used to compute the memorability of all given password. Across-tabulation was then employed out of the experiment using SPSS version 21. The result from the analysis revealed that the majority of the respondents do have weak passwords and also have few passwords which they even end up sharing with families and friends and reuse it. This confirms statements made by researchers that human being is the weakest connection in information system securities. To maintain Confidentiality, Availability and Integrity of data, the study therefore recommended the use of the Association Password technique which makes it easier to develop a much secured password that is difficult to crack but easy remember.

In this work SiC-Ti3AlC2 and TiC-Ti3AlC2 composites produced by additive manufacturing are investigated. The fused granules fabrication (FGF) method as one of the material extrusion additive manufacturing (MEAM) technology is used to obtain composite samples. Composites with different ratios between components and different powder:polymer ratios are investigated. The technological features of the additive formation of composites are investigated, as well as their structure and properties. The optimal sintering temperature to form the best mechanical properties for both composites is 1300 °C. The composites have a regulatable porosity. Ti3AlC2 content, sintering temperature, and polymer content in the feedstock are the main parameters that regulates the porosity of FGF samples.

Autism spectrum disorder (ASD) is a neurodevelopmental disorder characterized by impairments in social interaction and communication, anxiety, hyperactivity, and restricted interest for specific subjects. In addition to the genetic factors, multiple environmental factors have been related to the development of ASD. Animal models can serve as crucial tools for understanding the complexity of ASD and identifying potential therapeutic strategies. In this study, a chemical model of ASD has been developed in zebrafish by exposing embryos to valproic acid (VPA) from 4 to 48 hours post-fertilization. After the exposure, embryos were transferred to fish water and the effects on behavior and neurotransmitters profile were analyzed at both larval and adult stages. Larvae from VPA-treated embryos showed hyperactivity and decreased visual and vibrational escape responses, as well as an altered neurotransmitters profile, with increased glutamate and decreased acetylcholine and norepinephrine levels. Adults from VPA-treated embryos exhibited impaired social behavior characterized by larger shoal sizes and a decreased interest for their conspecifics. Neurotransmitter analysis revealed a significant decrease in dopamine and GABA levels in the brain. These results support the interest of this model in the study of ASD.

This study investigates the utilization of innovative green composites made from hemp shiv, a waste by-product of hemp cultivation, with the aim of promoting sustainability within the construction industry. The manufacturing method involve the application of pressure in a mold to create the samples. These materials were produced using an environmentally friendly binder consisting of colophony, arabic gum and corn starch, moreover white glue and bioepoxy are also used to compare with the green resins. Three different binder compositions for the specimens. The samples underwent mechanical testing through tensile and bending assessments, and their performance was compared to that of non-green binders to validate the effectiveness of the manufacturing processes. The study revealed that decreasing the moisture content during the curing process is crucial for improving the mechanical properties. The best results were achieved when using arabic gum as a binder, yielding a tensile strength of 2.16 MPa and a bending strength of 5.25 MPa, with a composition of 62.5% hemp shiv and a manufacturing process involving a pressure of 5 MPa.

This review summarizes studies dedicated to the assessment of microvascular function based on microcirculatory oscillations monitored by the FMSF technique. Two approaches are presented. The first approach uses oscillatory parameters measured under normoxia conditions, expressed as flowmotion (FM), vasomotion (VM), and the normoxia oscillatory index (NOI). These parameters have been used for identification of impaired microcirculatory oscillations associated with intense physical exercise, post-COVID syndrome, psychological stress, and erectile dysfunction. The second approach involves characterization of the microcirculatory response to hypoxia based on the measurement of hypoxia sensitivity (HS). The HS parameter is used to characterize microvascular complications in diabetes, such as diabetic kidney disease and diabetic foot ulcers. Based on research conducted by the authors of this review, the FMSF parameter ranges characterizing microvascular function are presented. The diagnostic approach to assessing microvascular function based on flowmotion monitored by the FMSF technique has a wide range of applications and potential to be integrated into widespread medical practice.

This study is based on the clamor of fish farmers for a cheaper fish feed alternative to current commercial feeds. At present, 70-80% of aquaculture costs come from feed cost, keeping farmers' income below their expectation. This study aimed to find alternative feeds or supplementary feeds that can perform similarly to the existing commercial feeds thereby reducing farmer expense and cutting down their cost of production and increasing their profitability. To do that, various indigenous raw materials were selected based on an earlier study which could result in a better feed alternative. The formulations for the study included four grow-out treatments mainly: control (commercial feed), taro+control (powdered Colocasia esculenta+commercial fish feed), bloodmeal (formulated fish feed based on bloodmeal), banana stem+control (chopped banana stem+commercial fish feed). A total of 12,000 fingerlings initially weighing 16 g (TL=10 cm) individually were assigned randomly to the four treatments (3000 in each cage measuring 6 x 6 m). Week zero was used for acclimation period, and fingerlings were fed with commercial fish feed. Then the first week used the treatment diets which were adjusted based on average body weight and sampled weekly (ABW=23g; TL=11 cm). The result of the study first showed significant differences between treatments on their fourth week in terms of the diet treatments (MS=0.103, df=3, F=4.12, P=0.0076) with the control and the taro+control showing no difference in terms of weight and length (TC vs CF; P=0.4524). But during the fifth week, the bloodmeal treatment showed increased weight and length for fish sampled (MS=0.109, df=3, F=4.10, P=0.0076) and provided similar weight and length as those from the taro+control and the control (TC vs CF; P=0.3721 and BM vs CF; P=0.0587). During the succeeding weeks, there were no significant differences between feed treatments from 6th weeks onwards, whether with weight [MS=0.130, df=3, F=1.14, P=0.333] or total length of the treatments [MS=0.008, df=3, F=0.40, P=0.75]. The FCR ratio showed taro (1.81) as lowest, followed by blood meal (2.09), and control (2.24) and then banana stem (2.84). In terms of weight gain, fish from the bloodmeal treatment gained the highest (236.97 g), followed by control (223.33 g), then taro (217.67 g) and banana stem (196.99 g). As a result, we find that the tested treatments such as bloodmeal formulated feed, taro+commercial feed, and banana stem+commercial feed can serve as an alternative to purely commercial fish feeds. Cost-benefit analysis showed that a better gross profit margin of 42% and cost-benefit ratio of 1.37 was observed in taro+commercial feed diet.

The recent availability of commercial platforms for behavioral analysis in zebrafish larvae based on video-tracking technologies has exponentially increased the number of studies analyzing different behaviors in this model organism to assess neurotoxicity. Among the most commonly used assays in zebrafish larvae are basal locomotor activity (BLA) and visual motor response (VMR). However, the effect of different intrinsic and extrinsic factors that can significantly alter the outcome of these assays is still not well understood. In this work we have analyzed in 143 larvae the influence of age (5-8 days post-fertilization), time of day (8:00, 10:00, 12:00, 14:00; 16:00, 18:00, and 20:00 h), and experiment (three experiments performed at different days) on BLA and VMR results (4,004 analyses for each behavior). Results from both behaviors were adjusted to a Random-Effects linear regression model using generalized least squares (GLS), including in the model the effect of the three variables, the second-way interactions between them and the three-way interaction. The results presented in this manuscript show a specific effect of all three intrinsic factors and their interactions on both behaviors, supporting the view that the most stable time period for performing these behavioral assays is from 10:00 am to 04:00 pm, with some differences depending on age of the larva and the behavioral test.

Hybrid reinforcement in a composite material (CM), in many situations, allows better govern material mechanical properties. Polymer matrix CM plate is reinforced with small particles and macro-fibers. Particles are oil shale ash (OSA) powder, macro-fibers – basalt fiber threads im-pregnated by matrix material. With the goal to find out elastic properties of the matrix- polymer with OSA, samples with its different concentrations were experimentally fabricated and their elastic properties were experimentally measured. Obtained data were used in numerical model-ling. Was observed polymer matrix composite slab, reinforced with OSA and three-dimensional (3D) basalt fiber fabric. Fabric are forming threads impregnated by matrix (polymer resin mixed with OSA particles). Damage accumulation in the stretched slab was modelled. Impregnated thread, in the modelling, is observed as a macro-fiber (MF) with averaged elastic properties. With the load increase MF in the material began to break. At first, appeared isolated single breaks. A probabilistic sequential MF rupture accumulation model was accepted and numerical-ly realized. The geometry of the reinforcing knitted fabric was modeled using the Leaf and Glaskin approach. In the knitted fabric highly, stressed MF cross-sections are observed as po-tential location where thread breakage can occur. If one thread breaks, the cross-sections of the adjacent threads experience the overload caused by this rupture. More overloaded crossection in the adjacent overloaded thread breaks and we obtain two adjacent broken MF designated as a defect with the size j=2. The probabilities of obtaining defect consisting of at least 2, 3, … j adjacent broken MF in the plate were calculated. The calculations continued until the rupture process becomes unstable (j→∞). The overstresses on adjacent threads in the CM were calculat-ed using the FEM three-dimensional numerical approach. Analytical and stochastic methods were used for the load-carrying capacity determination and different size defects accumulation in the hybrid composite material (HCM) plate. Also, was calculated the probability of the plate rupture.

Soil naturally contains fluorine, but concerns arise when its levels or bioavailability are increased by human activities or specific compounds. South Korea faces challenges in regulating soil fluorine pollution despite implementing stricter total fluorine standards than many developed countries. Moreover, these regulations can be economically unfeasible because of the naturally high background levels of fluorine in the soil in Korea. This review explores the global landscape of soil fluorine management strategies and examines potential solutions that reconcile environmental protection with economic concerns. We recommend a shift towards regulating specific and hazardous fluorine compounds rather than total content, and prioritizing remediation efforts based on assessments of bioavailable fluorine. This approach may help Korea establish a more effective and sustainable strategy for managing soil fluorine pollution.

Composites, and especially carbon fiber reinforced plastics (CFRPs), are increasingly used in the automotive, aerospace, and aviation industries, and as a result, CFRP production has increased dramatically, leading to a corresponding increase of waste. Landfill and incineration of waste are likely to be restricted as a result of the legislation, thus highlighting the need for efficient recycling methods for CFRPs. However, the recycling of CFRP is very challenging, mainly due to the difficulty of removing the thermosetting matrix. This study reports a pre-screening of the solvolysis recycling process for CFRPs based on the mechanical properties of the recovered fibers. To this end, solvolysis tests were conducted on unidirectional CFRP samples under supercritical and subcritical conditions using acetone and water. The solvolysis tests were conducted for various conditions of temperature, pressure, and reaction time. The efficiency of the recycling processes has been evaluated through a morphological and a mechanical characterization of the recovered fibers. In most cases, the decomposition efficiency of the epoxy resin, measured in terms of mass, ranged between 90 and 100%. Moreover, the scanning electron microscopy images of the recovered fibers showed negligible traces of resin residues and no detectable signs of physical damage or any changes in morphology with regard to diameter. Finally, the single-fiber tension tests revealed that that the recovered fibers retained more than 61% of their initial Young's modulus and 70% of their tensile strength.

The COVID-19 pandemic over the past years has shown a great need for rapid, low-cost and on-site detection of severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2). In this paper, an aptamer-based colloidal gold nanoparticle lateral flow test strip was well developed to realize the visual detection of wild type SARS-CoV-2 spike protein (SP) and multiple variants. Under the optimal reaction conditions, a low detection limit of SARS-CoV-2 S protein of 0.68 nM was acquired, and the actual detection recovery was 83.3% to 108.8% for real world samples. This suggests a potential tool for the prompt detection of SARS-CoV-2 with good sensitivity and accuracy, and a new method for the development of alternative antibody test strips for the detection of other viral targets.

Background: Removable prostheses have seen a fundamental change recently because of advances in polymer materials, allowing improved durability and performance. Despite these advancements, notable differences still occur amongst various polymer materials and processing technologies, requiring a thorough grasp of their mechanical, physical, and therapeutic implications. Methods: Fours different processing techniques, all utilizing Polymethyl methacrylate (PMMA) as the main material, were used to construct complete dentures. The specimens underwent a mechanical test. Results: All the specimens broke under the influence of a certain force, rather than yielding through flow, as is characteristic for plastic materials. For each specimen, the maximum force (N) was recorded (figure 4), as well as the breaking energy, Conclusions: The best results were obtained in the case of the thermoplastic injection system and, surprisingly and contrary to those in the specialized literature, the worst results were recorded in the case of 3D printed samples.

Steel structures, such as bridges, must be continuously maintained. Due to increasing trac loads, design and execution shortcomings, many steel bridges are subject to various types of damage, such as cracks. The bridges must be maintained by crack removal and re-welding the cracks. During this work, the bridge is closed for trac in order to suppress the crack ank movement during welding. As a result, trac loads on other routes are higher, which increases further damage on detour routes and subsequently additional welding work and costs on theses structures. Therefore, the aim is to provide a method that allows welding work on steel structures under running trac, respectively under cyclic loads. First, measurements at a representative steel bridge were conducted to derive gap opening parameters of amplitude and frequency for welding tests under cyclic loads. In a test setup for reproducible and comparable welding tests, specimen were welded under cyclic loads. Deep grinding of the root layer allowed defect-free welding within the range of 0.1 mm amplitude at a frequency of 2 Hz loadings. For such welds, the weld quality and the fatigue strength was comparable to the standard requirements.

Technological progress brings new tools to help society's development. In this context, the Internet of Things (IoT) helps to advance modern society. By connecting everyday objects and devices to the Internet, IoT enables benefits such as efficiency and automation, healthcare, environmental sustainability, safety, security, and data-driven decision-making. One of the possible technologies for devices' communication is LoRa, a wireless technology designed for the IoT that allows devices to communicate over long ranges using little battery power. This makes it useful for situations where it is needed to connect many devices spread out over a large area, like in smart cities or industrial settings. This paper aims to verify and evaluate the LoRa communication signal loss in a building environment. For this evaluation, we collected and processed data through experiments with LoRa links in the Instituto Federal de Pernambuco (IFPE) Campus.

Geopolymers, made from aluminosilicate raw materials, offer significant environmental advantages over conventional concrete (CC) mixes. This study explores the compressive strength, setting time, and durability of geopolymer concrete (GPC) cylinders, some of which include an additional ordinary portland cement (OPC) mix. Consistent material composition and testing methods are emphasized to achieve reliable results. MATLAB was utilized to develop and assess a neural network model predicting the compressive strength of GPC based on key variables. The model was validated using 16 experimental samples and 1047 samples from various studies. The performance plot displayed the Mean Squared Error (MSE) over iterations, identifying the best training performance at epoch 658 with an MSE of 5.3408. The Error Histogram highlighted distribution errors between predicted and actual compressive strength values, with the highest range from -1.015 to 0.3587, meaning that the predicted values were mostly within a small margin of error from the actual values. This narrow error range indicates that the ANN model has high accuracy in its predictions, as most errors are small and clustered around zero, demonstrating reliable performance in estimating compressive strength. Regression analysis showed varying correlation coefficients (training set R=0.98373, test set R=0.88164, and whole set R=0.96982), indicating adequate predictive accuracy. The results demonstrate that properly trained neural networks can effectively predict the compressive strength of GPC, highlighting its potential as a sustainable construction material.

In today’s rapidly evolving digital landscape, the significance of password guessing techniques in both offensive and defensive strategies is paramount. Passwords serve as a crucial line of defense for both individuals and corporations, safeguarding their sensitive systems and data. Therefore, assessing the effectiveness of these access credentials is a critical task. However, existing research in this field often encounters limitations, such as a lack of sufficient training data and extended model training times. Current methods often struggle with limited training data and lengthy training times. This paper introduces BBPE-AE, a novel Auto Encoder Network (AE) designed for password guessing. BBPE-AE utilizes Byte-level Byte Pair Encoding (BBPE) to extract frequent tokens from password datasets without length restrictions, employing a dynamic window technique to capture complex patterns. Experimental results on Hotmail and Myspace datasets demonstrate exceptional performance, achieving high similarity rates (BLEU-Unigram: 0.90, BLEU-Bigram: 0.82 for Hotmail; BLEU-Unigram: 0.90, BLEU-Bigram: 0.81 for Myspace). BBPE-AE generates realistic passwords that meet HIBP (Have I Been Pwned) standards, minimizing duplication. These findings highlight the effectiveness of BBPE-AE in enhancing security by generating realistic passwords, ultimately safeguarding sensitive systems and data.

In recent years, there has been a significant demand for Instructional Design (ID) professionals due to the rise of remote work, increased reliance on digital learning solutions for professional development, and the integration of digital technologies in formal and informal learning spaces. However, practical and authentic personalized courses are unavailable for professionals who want to transition into the field. This study addresses the gaps in most of the available ID courses and details the design of an Instructional Design Skill-Strength Assessment System (IDSSAS) that evaluates gaps in users' skills and offers them courses and mentors to help them bridge them in preparation for work as an ID in the corporate space. Employing a User-Centered Design (UCD) approach, the system prioritizes personalization, real-world application, and practical skills that better position them to be more employable, a significant improvement over the mostly available traditional, theory-focused ID training programs. IDSSAS, which is integrable with any Learning Management System (LMS) or Learning Experience Platform (LXP), was developed with Storyline 360, and it offers personalized learning and feedback as well as provides users with the agency to choose a mentor that is best aligned with their area of interest. The design was grounded in Self-Determination Theory (SDT) and incorporates design features like a progress bar, feedback loop, challenges, social interaction, and agency to support students' motivation and promote Autonomy, Relatedness, and Competence. IDSSAS, in its manual and present automated form, has been successfully used to mentor some transitioning ID professionals globally who are now gainfully employed.

A large set of undrained compression triaxial tests was carried out on different types of cohesionless soils, from sands to silty-sands and silts. Shear wave velocity measurements were carried out alongside. These tests exhibited distinct state transitions ranging from flow liquefaction to strain softening or strain hardening. With the purpose of defining a framework to assess soil liquefaction, it was found that the ratio between the shear wave velocity (VS0) and the peak undrained deviatoric stress, qpeak, VS0/qpeak, could be accurately used to define a boundary between liquefaction and strain hardening for sands, and between strain softening and strain hardening for silty-sands and silts. Since this ratio is a function of the tested material, it was also discovered that the prediction of these boundaries could be made as a function of soil grading, namely via the coefficient of uniformity, CU. Despite not being regarded as a strong geomechanical parameter, CU is easily determined from a grain-size distribution test and it has an empirically proven correlation with critical state parameters.

The importance of frailty in older people is getting constant recognition as an important aspect both in terms of public health, as well in personal level for the appropriate management of an older person health condition. This is reflected by the continuously increasing number of research studies carried out in several settings across different countries. Sometimes this is very solid, but in other cases there is a considerable gap in terms of accurate and well grounded documentation of frailty status. This is the case in Greece, where we are missing clinically validated tools to approach frailty. We are missing frailty screening tools, such as for instance PRISMA 7, the gold standard tool of Fried criteria is somehow problematic since the question referring to physical activity originates from a questionnaire that has not been translated and validated, while Clinical Frailty Scale has been validated for the translation but not for the capacity to detect frailty. Aim of this study is to validate these tools for their accuracy to detect frailty by using a measurable index of frailty, previously proposed for use in clinical studies: the Short Physical Performance Battery (SPPB). 74 male and female participants have been evaluated for their frailty status using different tools. We observed that PRISMA 7 translation detects frailty only when one question is removed at a cut-off of ≥ 2 and indicated a sensitivity of 88.1%, and specificity of 99.9% with a good correlation with SPPB measurements (r = 0.858; p < 0.001). When CFS was validated using SPPB it demonstrated a very good correlation (r = -0.838; p < 0.001 respectively) as it was the case for the modified Fried Criteria (r = -0.725; p < 0.001). All items demonstrated a good correlation between them. We can here propose that we can accurately assess frailty status in the community setting by using a modified version of Fried criteria, Clinical Frailty Scale translation in Greek and we can screen for frailty by using the Greek translation of PRISMA 7 only after removing the item 6 of the questionnaire.

this paper focuses on a scientific study of the restoration, rehabilitation and reuse of the great throne hall, the most important hall in al-jawhara palace. it also aims to study the most important factors and forces of damage that affected the great throne hall, natural, biological, and human, and the resulting damage. field tests were performed, laboratory tests to determine fracture stress, liquidity and spandex limits tests, chemical analysis on soil samples and geoelectrical testing of the soil, and the results did not show caves or voids in the ground until a depth of 10.00 m, construc-tion materials were studied and tested using x-ray, (xrd), mechanical tests (tensile, shear, com-pression), and a study of the effect of seismic loads on the walls; the results showed horizontal and vertical cracks; based on the study and analysis of these cracks, it was possible to present modern techniques in restoration and reinforcement methods, and in conclusion, the researcher's recommendations.

This study investigates the impact of specimen size on the mechanical properties of wood, specifically focusing on compression strength, elastic modulus, and Poisson's ratio. Compression tests were conducted using three different specimen sizes (20mm×20mm×30mm, 40mm×40mm×60mm, 60mm×90mm×90mm) in the longitudinal, radial, and tangential directions. Mechanical parameters, failure mechanisms, load-displacement curves, and stress-strain relationships were systematically analyzed for each size. The study also evaluated the influence of specimen size on the accuracy of finite element numerical simulations by utilizing the obtained mechanical parameters. The results reveal a significant correlation between compressive strength and specimen size, indicating a decrease in compressive strength with increasing specimen size. Conversely, elastic modulus and Poisson's ratio exhibit less sensitivity to variations in specimen size. Notably, parameters derived from small-sized specimens (20mm×20mm×30mm) exhibited substantial errors, while those obtained from medium-sized (40mm×40mm×60mm) and large-sized specimens (60mm×90mm×90mm) demonstrated greater reliability, providing precise results in finite element numerical simulations.

The acoustic startle response (ASR) is an explosive motor response leaded by a sudden and intense acoustic stimulus. ASR has several clinically relevant forms of plasticity, including habituation and sensorimotor gating. Although ASR and its plasticity have been intensively studied in different animal models, including zebrafish (Danio rerio) larvae, information in adult zebrafish is still very scarce. In this manuscript we present Zebra_K, a new automated high-content kinematic analysis platform for assessing ASR, its habituation and prepulse inhibition (PPI), a quantitative measure of sensorimotor gating, in adult zebrafish. The analysis of the kinematic parameters in 1,875 ASR in adult zebrafish has shown a single response wave consistent with the short-latency C-bend described in zebrafish larvae. Moreover, protocols have been designed and validated in Zebra_K for the analysis of sensitivity, habituation and PPI of this response. Then, this platform has been used to determine the effect of pharmacological and physiological modulators of ASR plasticity. As described in other animal models, the NMDA-receptor antagonist ketamine increased the responsiveness to the acoustic stimuli, decreasing habituation and leading to complete abolition of PPI. Moreover, the effect of the gender on zebrafish ASR plasticity has been analyzed for the first time. Females exhibited higher responsiveness and a lower habituation and PPI than males, a result consistent with the gender effect described in other animal models and in humans. These results enhance the interest of using adult zebrafish to assess the potential effect of chemicals or genetic manipulations on ASR plasticity.

The interlaminar strength of mechanically interlocked polymer-metal-interfaces is strongly dependent on the surface structure of the metal component. Therefore, this contribution assesses the suitability of the fractal dimension for quantification of the surface structure as well as interlaminar strength prediction of aluminum/polyamide 6 polymer-metal-hybrids. Seven different surface structures, manufactured by blasting, combined blasting and etching, thermal spraying and laser ablation, are investigated. The experiments are carried out on a novel butt-bonded hollow cylinder testing method that allows shear and tensile strength determination with one specific specimen geometry. The fractal dimension of the metal surfaces is derived from cross-sectional images. For comparison, the surface roughness slope is determined and related to the interlaminar strength. Finally, a fracture analysis is conducted. For the investigated material combination, the experimental results indicate that the fractal dimension is an appropriate measure for predicting the interlaminar strength

The present paper aims to increase knowlodge of the methods of resistance estimating of concrete in situ by means of non-destructive tests used to integrate the quantitative results from cylindrical specimens (core). The results of experimental investigations carried out on concrete conglomerate samples of a school building are shown. The experimental campaign then will be presented like a case study, conducted on a series of concrete beams and pillars of an existing building. The distructive tests on cores were conducted at the Civil Structures Laboratory of the Engineering Department of the University of Campania "Luigi Vanvitelli". The expression obtained through the calibration procedure of the values of non-destructive tests with those provided by the core drills allowed to estimate the average values of the compressive strength of the concrete. It is highlighted how this result was achieved with a very limited core number provided that they are extracted in selected points and that there was a proportionality link with the resistances obtained from non distructive tests.

The purpose of the study is to establish compliance of the design of the modernized car with the requirements for safe operation. An option has been proposed for upgrading a passenger wagon to a Mobile Diagnostic Complex for transporting a combined vehicle equipped with appropriate flaw detection equipment intended for rail diagnostics. The authors have established the most optimal option for locating the diagnostic vehicle on board the Mobile Diagnostic Complex (MDC) wagon, taking into account the additional load from the vehicle. To achieve this goal, the article developed a three-dimensional model of the supporting structure of the wagon body, proposed a methodology and presented the results of a study of the stress-strain state of the wagon body, taking into account the additional weight of the wagon. The article develops a methodology for studying the natural frequencies of vibrations of the wagon body and develops a three-dimensional model of the wagon for calculating dynamic indicators in the Universal Mechanism software package. Taking into account the previously carried out strength calculations, as well as in order to maintain the factory life cycle indicators of the supporting structure of the wagon body, it is recommended to use the model in the first version.

The objective of this study was to investigate the impact of athletes' respiratory muscle strength, as assessed through maximal inspiratory (MIP) and expiratory pressure (MEP), on aerobic endurance, as indicated by maximal oxygen consump-tion (Max VO2) kinetics. Respiratory muscle strength was assessed using a digital spirometer (Pony FX Cosmed, Italy), while maximal oxygen utilization capacity was measured using a breath-by-breath automatic portable gas analysis system (Cosmed K5, Italy). Statistical analysis was conducted utilizing SPSS 22.0. Based on the standardized regression coefficients (β), it was found that MEP (mean ± SD: 130.95 ± 42.82) and inspiratory diaphragmatic circumference values significantly influenced ventilatory equivalent (VE), oxygen consumption (VO2), and carbon dioxide pro-duction (VCO2). Conversely, the remaining predictor variables did not exhibit a sig-nificant effect on VE (mean ± SD: 134.80 ± 36.69), VO2 (mean ± SD: 3877.52 ± 868.47 ml), and VCO2 (mean ± SD: 4301.27 ± 1001.07 ml). In contrast, measurements of chest circumference (mean ± SD: 91.40 ± 10.72 cm), MEP, and diaphragmatic cir-cumference during inspiration (mean ± SD: 95.20 ± 10.21 cm) were found to signifi-cantly impact Max VO2 (mean ± SD: 58.52 ± 10.74 ml/kg/min), while the other pre-dictor variables did not demonstrate a significant effect on Max VO2. Conclusively, the study revealed that measured values of diaphragmatic circumference during inspiration and MEP exerted a notable influence on Max VO2, VE, VO2, and VCO2. Our findings underscore the importance of considering respiratory muscle strength in assessing and enhancing athletes' aerobic performance. These insights contribute to a deeper understanding of the interplay between respiratory function and exercise capacity, offering potential avenues for optimizing training regimens and perfor-mance outcomes in athletic contexts.

The work presents the results of numerical fatigue analysis of a turbine engine compressor blade, taking into account the values of initial stresses resulting from surface treatment - shot-peening. The values of the residual stresses were estimated experimentally using X-ray diffraction. The paper specifies the values of the residual stresses on both sides of the blade and their reduction due to the cutting through the blade - relaxation. The obtained values of the residual stresses were used as initial stresses in the numerical fatigue analysis of the damaged compressor blade, which is subjected to resonant vibrations of known amplitude. Numerical fatigue ε-N life analysis was based on the several fatigue material models: Manson’s, Mitchell’s, Baumel-Seeger’s, Muralidharan-Manson’s, Ong’s, Roessle-Fatemi’s and Median’s, and also on the three models of cyclic hardening: Manson’s, Xianxin’s, and Fatemi’s. Because of this approach, it was possible to determine the relationship between the selection of the fatigue material ε-N model and the cyclic hardening model on the results of the numerical fatigue analysis. Additionally, the calculated results were compared with the results of experimental research, which allowed for a substantive evaluation of the obtained results. These results are of great scientific and practical importance. The problem of determining the fatigue life of blades with defects operating under resonance vibrations is one of the original tasks in the field of fracture mechanics and experimental mechanics. The results obtained are of great importance in the aviation industry and can be used during engine maintenance and inspections to assess the suitability of blades with defects in terms of the needs of further work. This aspect of engineering maintenance is of great importance from the aircraft safety point of view.

Background/Objectives: High-intensity anaerobic physical training frequently results in muscle damage among boxers and kickboxers, which can impede performance and recovery. Vibrational therapy (VT) and passive rest (PR) have been employed as methods to enhance muscular recovery and performance. This study evaluates the effectiveness of these two recovery methods on upper limb muscle strength and lactate levels in plasma after high-intensity exertion. Methods: Eighteen elite boxers and kickboxers, aged 19-32 years, underwent tests employing VT and PR as recovery methods in a controlled, crossover study. Muscle performance was assessed via isokinetic dynamometry, and lactate levels were measured pre-exercise, post-exercise, and post-recovery. The study adhered to the Declaration of Helsinki guidelines and was approved by the relevant bioethics committee. Results: The results showed that VT led to a faster recruitment of muscle fibers and improved muscle endurance as indicated by decreased fatigue work indices compared to PR. However, no significant differences were observed in peak torque or lactate levels between the two recovery methods. The VT group exhibited quicker recovery times in torque generation and better performance in fatigue resistance. Conclusions: VT appears to provide superior muscular recovery compared to PR following intense anaerobic effort, particularly in terms of muscle strength endurance and activation speed. These findings support the potential of VT in sports recovery protocols, although similar lactate response suggests that metabolic recovery rates are not significantly affected.

This work presents the results of three connection types in double-shear with dowel fasteners, using the simplified equations from the Eurocode 5. All design parameters were established and compared using three different wood strength and density properties, which constitute the members connections. Eighty-one connections were obtained, allowing to conclude about the number of fasteners needed to the applied tensile load. An increase in the number of dowels was obtained with the increased applied tensile load, lower dowel diameter, lower wood density, and lower strength material in all connection types in the study. The design characteristic load-carrying capacity per shear plane and fastener also decrease with the previously considered parameters.

China is facing the development requirements of the dual carbon goal and the construction needs of resilient cities. Currently, high-strength composite structural systems are a feasible solution, but their research and application in the construction field are insufficient, especially for the combination forms of concrete above C100 and steel above Q550. In response to this issue, this paper proposes a new high-performance structural system, namely the composite frame - high-strength steel plate wall core tube resilient structure system, which includes high-strength steel plate (Q550) - ultra-high strength concrete (C100) shear walls, replaceable energy dissipation coupling beams, and composite frames. Taking a 200 meter building as an example, this paper designs and establishes calculation models for a conventional reinforced concrete frame-core tube structure and a high-performance structure based on PKPM software, and establishes elastoplastic analysis models for both based on SAUSAGE software, and then conducts dynamic elastoplastic time history analysis and seismic resilience assessment of structures under design basis earthquakes (DBEs), maximum considered earthquake (MCEs) and extremely rare earthquakes (EREs). Research has shown that compared to conventional structures, new high-performance structures can effectively reduce the size of shear walls, reduce the self-weight of the structure, and enhance the space for building use; The story drift ratio has higher redundancy than specification limits, lower plastic damage and overall stiffness degradation of the structure, and better seismic performance; The seismic resilience has significantly improved, especially in the case of casualties, which can better ensure the safety of people's lives and property.

This study investigates the compressive strength and workability of concrete incorporating coconut shells and bamboo strips as alternative aggregates. The research compares traditional concrete to concrete mixtures with varying percentages of coconut shells and bamboo strips. Specifically, the study examines the effects of adding 10% coconut shell, 10% bamboo strip, and a combination of 5% coconut shell and 5% bamboo strip by volume to the concrete mix, tested in both C20 and C30 grades. To prepare the materials, coconut shells and bamboo strips were first crushed and then sieved. The sieving process retained particles that passed through a 10mm sieve but were retained on a 4.7mm sieve. The primary focus of the experimental tests was on measuring the compressive strength of the resulting concrete mixtures. The findings indicate that concrete incorporating coconut shells showed moderate workability. In contrast, concrete with bamboo strips exhibited lower workability. Regarding compressive strength, the concrete mix containing a combination of 5% coconut shell and 5% bamboo strips demonstrated a reduction in strength compared to the control group of normal concrete. This research highlights the potential of using coconut shells and bamboo strips as sustainable alternatives in concrete construction. While the workability varies between the different materials, the results provide valuable insights into their suitability for specific applications. This encourages further exploration of eco-conscious building practices and the development of sustainable construction materials.

Yttria stabilized zirconia materials are frequently used in mechanical engineering and biomedical applications. Demanding loading conditions require materials combining a high level of strength and fracture toughness. A ready to press alumina doped 2 mol% yttria stabilized zirconia powder was shaped by axial pressing and sintering in air at 1250 - 1500 °C for 2 h. The best combination of strength and toughness value of 7.8 MPa√m. Materials sintered in the middle of the chosen temperature range combine fully density, high transformability and small grain size. Toughness measurements by direct crack length measurements delivered unrealistically high fracture toughness values.

Background Sarcopenia is a state with progressive and generalized loss of skeletal muscle mass and strength. It is a serious complication occurring in chronic kidney disease (CKD) patients which increases morbidity and mortality rate. Sarcopenia is diagnosed when loss of both compartments - muscle strength and skeletal muscle quality or quantity are present. However, there are still numerous patients, also with CKD, diagnosed as pre-sarcopenic individuals with low muscle strength and normal skeletal muscle quality or quantity and conversely, with correct muscle strength and decreased skeletal muscle mass, who are prone to develop sarcopenia in future life. It is crucial to examine numerous variables possibly associated with changes of skeletal muscle mass and muscle strength in terms of preventing the development of sarcopenia. The aim of the study was to investigate anthropometric and clinical correlates and sources of variation in both skeletal muscle mass and muscle strength in advanced stages of CKD. Methods The study sample consisted of 84 non-dialysis dependent patients of both sexes (including 45.2% of women) with eGFR < 45 ml/min/1.73m²: 26.2% with eGFR 30-44 mL/min/1.73 m², 65.5% with eGFR 15-29 mL/min/1.73 m² and 8.3% with eGFR < 15 mL/min/1.73 m². Muscle strength was estimated by measuring hand grip strength (HGS) with the use of handheld hydraulic dynamometer. Muscle quantity was measured by bioimpedance spectroscopy using Body Composition Monitor. Appendicular skeletal muscle mass (ASM) was calculated according to Lin’s formula. Serum creatinine, urea, uric acid and albumin were measured. Results In bivariate analysis we found that ASM significantly and positively correlated with anthropometric variables such as body mass (r=0.903, p<0.001), NH weight (r=0.882, p<0.001), height (r=0.694, p<0.001), body mass index (BMI) (r=0.701, p<0.001), lean tissue mass (LTM) (r=0.664, p<0.001), lean tissue index (LTI) (r=0.433, p<0.001), fat mass (r=0.614, p<0.001) and fat tissue index (FTI) (r=0.449, p<0.001), and was negatively associated with clinical variable such as hydration status (p<0.001). HGS significantly and positively correlated with anthropometric parameters such as body mass (r=0.319, p=0.003), NH weight (r=0.315, p=0.004), height (r=0.666, p<0.001), LTM (r=0.490, p<0.001), LTI (r=0.238, p=0.029), and ASM (r=0.501, p<0.001), and was negatively associated with clinical variables like uric acid (p=0.039) and urea (p<0.001). After adjustment for age, sex and height, HGS remained significantly and negatively related with uric acid (β=-1.078, p=0.041) and hydration status (β=-0.805, p=0.042). Conclusions In CKD patients, ASM is determined mainly by anthropometric parameters but HGS - both by anthropometric and clinical variables specific for CKD.

Currently, in some domestic and foreign mines, the backfill drilling pipeline experience a rupture phenomenon even when the wear degree is low. This results in a delay in production due to the filling becoming 'sick'. This paper presents, for the first time, the damage mechanism from a mechanical perspective and re-derives the anti-extrusion strength model of the backfill drilling pipeline. We investigate the influence of law on the anti-extrusion strength of pipelines from the perspective of stratum and cement ring. We then verify the theoretical and simulation results through engineering examples. The results demonstrate that the Mises stress criterion is a suitable modification principle for the anti-extrusion strength model of the backfill drilling pipeline. The anti-extrusion strength of the pipeline is related to the elastic modulus and Poisson's ratio of the stratum, and the thickness of the cement ring. It is negatively affected by the depth of the stratum. For hard strata, a cement ring with a smaller elastic modulus is suitable, while for soft stratum, a cement ring with a larger elastic modulus is recommended. When the missing angle of the cement ring is less than 60°, the stress concentration factor increases up to 2.2. The stress unloading capacity of the cement ring ranges from 32.7% to 37.8%, and optimal performance of the cement ring is achieved when it has high strength and low rigidity. The backfill filling pipeline of a copper mine abroad was destroyed due to external extrusion force exceeding its anti-extrusion strength value. The modified pipeline anti-extrusion strength model is 18.2% higher than the casing API strength value. This finding can inform the design of the backfill filling pipeline for China's kilometer-deep wells in the future.

The existing PDC(Polycrystalline Diamond Compacts) -cone hybrid bit bearing adopts a unilateral support structure, which is prone to stress concentration in the journal area, resulting in fracture and wear failure of the bearing, thus reducing the service life of the hybrid bit. In this paper, a new type of double supported bearing hybrid bit is proposed. The static strength analysis of unilateral and bilateral support bearing structures is carried out by finite element simulation, and the stress and strain distribution of the two structures under the load of 20KN-100KN is obtained. Experimental devices for unilateral and bilateral support bearing structures are designed and manufactured to complete 50KN-100KN static pressure loading experiments. The results showed that the stress and strain of unilateral and bilateral support bearing increased linearly with the increase of load. Compared with unilateral bearing, when the load was 100KN, the maximum Mises stress of bilateral bearing decreased from 358.80MPa to 211.10MPa, with a decrease of 41.16%. The maximum contact stress decreased from 415.20MPa to 378.10MPa, decreased by 8.94%, and the maximum principal strain decreased from 11.01e-4 to 9.71e-4, decreased by 11.81%. The axial strain in the danger zone was reduced by 14.68% and 17.35%, respectively. It is found that the contact stress of the simulation data is highly correlated with the bearing life, and the service life of the bilateral bearing bit is increased by 8.94%. The simulation data and experimental results provide data support for the production of hybrid bits with bilateral bearing support.

This study is focused on the mechanical properties of WC-Co composites obtained via Selective Laser Sintering using PA12 as a binder. The as-printed samples were thermally debonded, and sintered, first in vacuum, and then sinter-HIPed at 1400oC, using 50 bar Ar, which has led to relative densities up to 66 %. Optical metallographic images show a microstructure consisting of WC, with an average grain size in the range of 1.4 – 2.0 µm, with isolated large grains, in a well-distributed Co matrix. The shrinkage of the samples was 43 %, with no significant shape distortion. The printing direction of the samples has a great impact on the transversal rupture strength (TRS). Nevertheless, the bending strength was low, with a measured maximum of 612 MPa. SEM images of the fracture surface of TRS samples show the presence of defects that constitute the cause of the low measured values. The hardness values position the obtained composites in the range of medium coarse classical cemented carbides. The results were also related to the amount of free Co after sintering, close to the initial one, as assessed by magnetic measurements, indicating a low degree of interaction with PA12 decomposition products.

This paper presents a review on numerical and experimental methods to predict fracture of ad-vanced high strength steels (AHSS). AHSS are widely processed through sheet metal forming processes. Although being an excellent choice when lightweight, high strength and ductility are critical factors, their multi-phase microstructure accentuates forming challenges. To accurately model forming behavior, necking based failure criteria as well as direct fracture models require improvements. As a necking based failure model, the conventional forming limit diagram/curve (FLD/FLC) presents limitations such as in estimating direct fracture (surface cracks, edge cracks, shear cracks), as well as deformation histories under nonlinear strain paths. Thus, significant re-search efforts are being made towards the needs of advanced fracture constitutive models capa-ble of predicting fracture scenarios without necking, more frequently observed in the realm of AHSS. Scientific community research is divided into several directions aiming at improving the forming and fracture behavior accuracy of parts subjected to sheet metal forming operations. In this review paper, a comprehensive overview on ductile fracture modeling is presented. Firstly, the FLD/FLC limitations modeling fracture behavior in sheet metal forming operations are stud-ied. Followed by the recent trends in constitutive material modeling. Afterwards, material char-acterization methods advancements to cover a broad range of stress states are comprised. Final-ly, damage and fracture models predicting failure in AHSS are investigated. This review paper supplies relevant information on the current issues the sheet metal forming community is chal-lenged with due to the trend towards AHSS employment in the automotive industry.

Based on the dynamic strength variation mechanism of concrete under complex loading conditions, two approaches were devised: numerical testing and CT scanning, guided by the principle of minimizing energy dissipation. A methodology for calculating concrete's failure area and measuring its strength was developed. The analysis delves into the mechanisms behind failure patterns and variations in concrete specimen strength, focusing on crack initiation, development, and the resultant failure surface formed by crack propagation, along with the stress distribution in concrete specimens subjected to diverse loading conditions. Through evaluating the strength and computed failure area of concrete specimens, it is evident that the loading method influences both the strength and failure area of concrete specimens. In general, a larger failure area correlates with a higher measured strength.

With continuous increase in integration of the semiconductor devices, the requirements on size accuracy and surface quality of the etched lead frame are higher. The etchant is a key factor on etching process and etched surface quality, while effects of the difference in etchants on microscopic etched surface morphology of the Cu alloy have not been directly studied. In this study, the aqua regia, acidic FeCl3 and CuCl2 solutions were used as etchants, and the CuCrSn alloy specimens with different microstructure were etched and characterized. The results show that the etching rate in aqua regia is high, and the grain orientation, grain boundary (GB) and dislocation have significant influence on the local etching rate. The preferential etching of some atomic planes forms steps between grains with different orientations, and the preferential etching around the GB and dislocation group forms grooves, resulting in high surface roughness. For etching of the FeCl3 and CuCl2 etchants, the steps and grooves become blurred, and almost invisible on the surface etched by the CuCl2 etchant, thus the surface roughness is much lower. The CuCrSn alloy surface etched by the aqua regia is clean, with little Cr-rich particles, while high density Cr-rich particles are remained on the surfaces etched with the FeCl3 and CuCl2 etchants. For the same kind of etchant, the ion concentration can affect the etching mechanism and etching surface morphology.

The aim was to evaluate the agreement between plaque detection with intraoral scanner system (IOS) and a conventional clinical method and to evaluate the inter-rater reliability for scoring 3D models with and without a disclosing agent. 14 participants were recruited from the Department of Operative Dentistry, School of Dentistry, University name blinded to reviewers, it is completed after the reviewing process. Participants eligible for inclusion were adults with good general health and a minimum of 20 teeth. Participants were clinically examined with plaque assessment according to the modified Quigley-Hein plaque index before and after using a disclosing agent (GC-Tri Plaque ID-Gel, GC). Before and after the application of the disclosing agent, all study participants were scanned using the IOS (TRIOS5, 3Shape TRIOS A/S). The clinical examiner and additional three examiners blinded to the clinical examination assessed plaque status on the acquired 3D models with and without disclosing agent using the same index to evaluate the inter-rater agreement. Intraclass coefficient correlation, one sample t-test and Cronbach’s α for inter-rater reliability were calculated. All methods showed moderate to strong correlations (Spearman’s rho ranging from 0.527 to 0.618) and Cronbach’s α ranged from 0.551 to 0.766. Level of agreement between con-ventional clinical registration and registration from 3D models was acceptable overall.

Infrastructure development is rapidly increasing, driving up demand for concrete, a key construction material. Cement and aggregate are essential constituents, with global cement production reaching 4.1 billion metric tons in 2011 and CO2 emissions hitting 1.7 billion metric tons by 2024, a significant contributor to carbon emissions. To address this, alternative constituents like Rice Husk Ash (RHA) and Animal Bone Powder (ABP) are proposed. With rice husk comprising 20% of rice weight and a substantial cattle population in Bangladesh, RHA and ABP offer promising alternatives. This study examines the benefits and limitations of incorporating RHA and ABP into cement, focusing on concrete strength and permeability. By replacing varying percentages of cement with RHA and ABP simultaneously, experiments evaluate their impact on concrete properties after 28 days of curing. The research aims to identify the optimal combination for sustainable concrete production, reducing environmental impact by curbing waste generation and pollution. Results show that compressive strength increases and permeability decreases with up to 5% replacement of RHA and ABP, highlighting their potential for enhancing concrete performance while mitigating environmental concerns.

Although, promotion of urbanization culture in recent decades has made inevitable development of cities in the world, however, the development can be guided in a direction that leave, to the extent possible, minimum socioeconomic and environmental impacts. For this, it is required to first forecast auto-spreading orientation of cities and suburbs in rural areas over time and then avoid shapeless growth of cities. This paper is an attempt to develop a dynamic hybrid model based on logistic regression (LR), Markov chain (MC), and cellular automata (CA) for prediction of future urban sprawl in fast-growing cities. The model was developed using 12 widely-used urban development criteria, whose significant coefficient was determined by logistic regression, and validated by relative operating characteristic (ROC) analysis. The validated model was run in Guilan, a tourist province in northern Iran with a very high rate of urban development. For this, changes in the area of urban land use were detected over the period of 1989 to 2013 and then, future sprawl of the province was forecasted by the years 2025 and 2037. The analysis results revealed that the area of urban land use was increased by more than 1.7 % from 36012.5 ha in 1989 to 59754.8 ha in 2013, and the area of Caspian Hyrcanian forestland was reduced by 31628 ha. The results also predicted an alarming increase in the rate of urban development in the province by the years 2025 and 2037, during which urban land use is predicted to develop 0.9 % and 1.38 %, respectively. The development pattern is expected to be uneven and scattered, without following any particular direction. The development will occur close to the existing or newly-formed urban basements as well as around major roads and commercial areas. This development, if not controlled, will lead to the loss of 13863 ha of Hyrcanian forests and if the trend continues, 21013 ha of Hyrcanian forests and 20208 ha of Barren/open lands are expected to be destroyed by the year 2037. In general, the proposed model is an efficient tool for the support of urban planning decisions and facilitates the process of sustainable development of cities by providing decision-makers with an overview on future development of cities where the growth rate is very fast.

Background/objective: Tools to accurately and efficiently measure the dietary intake of Nigeria are lacking. We aimed to develop and assess the usability of a new online dietary assessment tool for Nigeria, myfood24 West Africa. Methods: We developed myfood24 West Africa database using data from existing food composition tables, back-of-pack labels of packaged foods and research articles. A 7-step approach was used: identified data sources, selected foods, processed/cleaned data, calculated nutrient content of recipes, created/allocated portion sizes, quality-checked database, and developed food accompaniments. To pilot myfood24 West Africa, we recruited 179 university staff living in Nigeria using a cross-sectional design; usability was assessed using a questionnaire that incorporated the System Usability Scale (SUS) and feedback session. Results: The database included 924 foods with up to 54 nutrients and 35 portion-size images allocated to foods. 60% of the data were sourced from the 2019 West Africa Food Composition Table, 17% from back-of-pack labels, 14% from the 2017 Nigeria Food Composition Table, 5% from generated recipes and 4% items from published literature. 30% (n=53) self-recorded their diet on their own and 1345 entries were made. The mean SUS score of 74 (95% CI: 68,79) indicated good usability. The feedback showed the tool was easy to use, educative, and included a variety of locally foods consumed. Conclusion: This new tool will enhance the dietary assessment of the Nigerian population. More work will cover more foods from other regions of Nigeria and West African countries.

Anthropogenic development can strongly influence natural river processes, leading to environmental changes that negatively affect important habitats and biodiversity, and consequently reduce economically important natural resources. This study investigated the effects of salinity intrusion on the habitat of the clam Corbicula japonica in the Seomjin River estuarine zone. We employed the Environmental Fluid Dynamics Code (EFDC) model, which incorporates topographic data and hydrological changes, to simulate salinity concentrations. Two salinity measurement facilities were installed in Seomjin River estuarine and operated to optimize the EFDC model. The results show that reduced flow rates due to intake have a negligible impact on the increased salinity. Maintaining optimal salinity (15–20 psu) during neap tides at the Seomjin River Bridge requires constant high flow rates, which poses significant challenges. Saltwater stratification is identified as the primary cause of pronounced salinity stratification, particularly during neap tides. Addressing this issue through river discharge and intake facility operation is challenging. Structural measures, including riverbed restoration and underwater barriers, are recommended to improve resistance to seawater intrusion. Future research should aim to develop scenarios to reduce salinity concentrations, quantify the reduction efficiency, and propose region-specific measures.

The objective was to assess the instrumental validity and the test-retest reliability of a low-cost hand-held push dynamometer adapted from a load-cell based hanging scale (tHHD) to collect compressive forces in different ranges of compressive forces. Three independent raters applied 50 pre-established compressions each on the tHHD centered on a force platform in 3 distinct ranges: ~70 N, ~160 N, ~250 N. Knee isometric strength was also assessed on 19 subjects in two sessions (48h apart) using the tHHD anchored by an inelastic adjustable strap. Knee extension and flexion were assessed with the participant seated on a chair with the feet resting on the floor, knees, and hips flexed at 90°. The isometric force peaks were recorded and compared. The ICC and the Cronbach’s α showed excellent consistency and agreement for both instrumental validity and test-retest reliability, as the correlation and determination coefficients. The SEM and the MDC analysis returned adequate low values with a coefficient of variation less than 5%. The Bland-Altman results showed consistency and high levels of agreement. The tHHD is a valid method to assess the knee isometric strength, showing portability, cost-effectiveness, and user-friendly interface to provide an effective form to assess the knee isometric strength.

Concrete contributes 8% of all global carbon emissions making the need to find substitute critical for environmental sustainability. Research has indicated the potential for recycled plastics to be used as concrete substitutes. This study extends existing research by investigating the use of polycarbonate (PC) in plastic sand bricks as a mechanical equivalent to concrete. PC has high compressive strength, durability, impact strength, thermal resistivity, clarity, fatigue resistance, and UV resistance. This work provides a method and mold to produce a matrix of sand-plastic sample compositions with dimensions adhering to ASTM D695 standard for compressive properties of rigid-plastic. Compositions of 0% (control), 20%, 30%, 40%, and 50% sand by weight were tested. Samples were tested for compressive strength until yield and stress-strain behaviors plotted. The results for 100% PC demonstrated an average and maximum compressive strength of 71 MPa and 72 MPa, respectively. The 50% PC and 50% sand composition yielded an average and maximum compressive strength of 71 MPa and 73 MPa respectively with an increase in compressive stiffness, and transition to shear failure resembling cement. With a composite density of 1.86 g/cm3 against concrete’s average 2.4 g/cm3, and a compressive strength exceeding commercial concrete demands of 23.3 MPa to 30.2 MPa, this lightweight alternative meets the strength demands of concrete, reduces the need for new construction materials, and provides an additional recycling opportunity for nonbiodegradable waste plastic.

The Simultaneous Localization And Mapping (SLAM) scanner is an easy and portable Light Detection And Ranging (LiDAR) data acquisition device. Its main output is a 3D point cloud covering the scanned scene. Regarding the importance of accuracy in the survey domain, this paper aims to assess the accuracy of two SLAM scanners: the NavVis VLX and the BLK2GO Scanner. This assessment is conducted for both outdoor and indoor environments. In this context, two types of reference data are used: the Total Station (TS) and the static scanner Z+F Imager 5016. To carry out the assessment, four comparisons are tested: cloud to cloud, cloud to mesh, mesh to mesh, and edge detection board assessment. However, the results of the assessments confirm that the accuracy of indoor SLAM scanner measurements (5 mm) is greater than that of outdoor ones (between 10 mm and 60 mm). Moreover, the comparison of cloud to cloud provides the best accuracy regarding direct accuracy measurement without manipulations. Finally, based on the high accuracy, scanning speed, flexibility, and the accuracy differences between tested cases, it is confirmed that SLAM scanners are effective tools for data acquisition.

This study investigates by hybrid approach of classical calculations and numerical explicit FEM simulation the strain rate sensitive hardening of Polypropylene Sabic 83MF10 under dynamic tension loads. The Cowper-Symonds model is employed to characterize the non-linear increase in yield strength with strain rate, within the range of 0,01 to 1 [1⁄s]. For lower strain rates, a drastic decrease in yield strength is observed, suggesting the significant influence of creep and relaxation phenomena. The study proposes further research incorporating viscoelastic properties for a more comprehensive material model. Additionally, the study observes a disproportionate increase in yield strength for samples with smaller radius, indicating a dependency on triaxiality which suggests further research on the Drucker-Prager model for this material. The study concludes by recommending a broader range of input parameters for future studies, including the Johnson-Cook model and comparison of tensile test results with compression test results.

The new slide roller burnishing (SRB) method has been developed to produce mirror-like surfaces. Unlike conventional roller burnishing (RB), SRB is implemented through a unique device that allows the axes of the deforming roller and the rotary workpiece to cross resulting in a relative sliding velocity that can be controlled (in magnitude and direction) by varying the crossing angle. In the present work, the effect of SRB on the fatigue behavior of AISI 316 steel fatigue specimens was investigated by comparing with a conventional RB using the basic correlation in surface engineering: finishing–surface integrity (SI)–operating behavior. To obtain a more representative picture of the comparison, we implemented each method (RB and SRB) with two combinations of governing factors: (A) a radius of the roller toroidal surface of 3 mm, a burnishing force of 250 N and feed rate of 0.05 mm/rev (RB-A and SRB-A) and (B) a radius of the roller toroidal surface of 4 mm, a burnishing force of 550 N and feed rate of 0.11 mm/rev (RB-B and SRB- B). Both SRB-A (crossing angle of –45°) and SRB-B (crossing angle of –30°) achieved mirror-finish surfaces. SRB-B lead to the greatest fatigue strength and, thus, the longest fatigue life among all tested processes. SRB-B created the deepest zone (&gt;0.5 mm) with residual compressive macro-stresses and a clearly defined modified surface layer, whose thickness of more than 20 m is about twice that created by the other three processes.

The alternating stress caused by periodic high-pressure injection and extraction in gas storage can potentially induce fault slippage, compromising the sealing integrity of faults within these facil-ities. Understanding the mechanical behavior of faults under alternating stress is crucial for en-suring the long-term stability and safety of gas storage operations. To explore the impact of fault dip angle and fault gouge strength on fault slip characteristics, fault samples were prepared with uniaxial compressive strengths of 20.1, 30.2, 42.4, and 51.4 MPa at two distinct dip angles. Triaxial compression experiments were conducted under alternating stress conditions corresponding to operational pressures at a specific gas storage in China. Results indicate that faults with dip angles of 30° and 45° tend to fail at their weakest points. Increasing strength of fault gouge shifts failure mechanisms from interfacial failure between gouge and surrounding rock towards internal gouge failure, often accompanied by shear failure across sections, resulting in characteristic "X"-shaped conjugate shear failures. The decrease in the ratio of bedrock strength to fault gouge strength elucidates the observed phenomena of initial reduction followed by increased fault deformation. Transition points for faults with 30° and 45° dips occur around the strength ratios of 1.7/1 and 1.2/1, respectively. Fault damage exhibits a negative correlation with fault gouge strength and a positive correlation with fault dip angle. Samples with higher strength fault gouge at a 30° dip angle generally incur less damage compared to those with lower strength fault gouge at a 45° dip angle. Moreover, higher maximum static friction coefficients denote greater fault resistance to slipping, with 30° faults consistently demonstrating superior resistance compared to 45° faults. Additionally, higher strength fault gouge consistently enhances slip resistance under identical dip angles.

Background This study aimed to examine the acute effects of different pre-ST strategies on muscular performance and blood pressure (BP) responses in recreationally strength-trained women. Methods: Twelve overweight women with normal-to-elevated BP were recruited and performed six exper-imental protocols in a randomized order: 1) control protocol (CC) – BP assessed without exercises performed, 2) strength training (ST), 3) foam rolling warm-up followed by strength training (FR+ST), 4) specific warm-up followed by strength training (SW+ST), 5) aerobic exercise followed by strength training (AE+ST), and 6) stretching exercises followed by strength training (SE+ST). Strength training consisted of three sets at 80% of 10RM with a self-suggested rest interval between sets for bench press, back squat, bench press 45º, front squat, lat pull-down, leg press, shoulder press, and leg extension. Results: All experimental protocol had a lower total training volume, fa-tigue index, and repetitions performance in relation to ST (p

As high strength and ultra-high strength steels are widely used in all kinds of modern welded constructions, a lot of research is carried out to investigate the mechanical properties of weldments of these steels but there is a scarce information on such important characteristic as their corrosion behaviour. This research focuses on the corrosion behaviour of weld metal of weldments of S906QL and S700MC steels. Weld metal was tested electrochemically in a 3,5% NaCl aqueous solution via potentiodynamic scan to determine corrosion rate and its dependence on welding gap. No influence of welding gap on corrosion rate was found but the experimental results suggested that corrosion rate depended on the chemical composition of filler material and the microstructure of weld metal.

To explore the effect of lily polysaccharide (LP) on immune function and intestinal flora in immunosuppressive mice.The immunosuppressive model was established by intraperitoneal injection of cyclophosphamide (CTX) in mice, and the immunological indexes were measured. The cecal contents of mice were taken, and the DNA of intestinal flora was extracted for 16S DNA sequence analysis.Compared with CTX group, the body weight and thymus index of mice in each treatment group increased significantly, the liver index decreased significantly,the hepatocyte morphology, liver plate and hepatic sinus arrangement of mice in high and low concentration LP groups were relieved in varying degrees, and the contents of IgA and IgG in serum of mice in low concentration LP group and positive control group increased significantly; The contents of TNF-α and IL-6 in colon decreased, while the contents of IL-10 increased significantly. The contents of AST, ALT and MDA in liver decreased significantly, while the content of SOD increased significantly. Compared with the blank group, LP can improve the intestinal flora of immunosuppressive mice , mainly by increasing the abundance of beneficial bacteria such as s24-7, Bacteroides and butyrimionas and reducing the abundance of harmful bacteria such as Prevotella, dorea and adlercreutzia.

Evidence suggests that COVID-19 infection can cause lasting health consequences. Multidiscipli-nary rehabilitation services have been recommended to reduce the sequalae. However, the effec-tiveness of physical exercise interventions remains insufficiently documented. The aim of this study was to develop and implement a specific and well tolerated protocol-based, intervention to reduce muscle weakness in older adults impacted by COVID-19. Forty six older adults random-ized into Intervention and Control Groups. Isometric and isokinetic strength assessments were conducted for selected muscle groups using JBA Staniak® torquemeter and Biodex System 3 dy-namometer. Functional abilities were evaluated with the Time Up and Go test and Chair Stand Tests. Men in intervention group demonstrated a significant improvement in static conditions for knee flexors (KF), trunk extensors (TE) and trunk flexors (TF) and in dynamic conditions for knee extensors (KE). Women in intervention group showed significant improvement in static condition for EF, KF, TE and TF and in dynamic for a KE and for a KF. The interaction GROUP x TESTING SESSION was significant for Chair test (s) and Chair test (n). Our results demonstrate the effec-tiveness of a well-tolerated, protocol-based approach that can be used to diminish long lasting functional deficits in post-covid survivors.

Sialyllactose (SL) is a functional human milk oligosaccharide essential for immune support, brain development, intestinal maturation, and antiviral defense. However, despite its established health benefits, the effect of SL on exercise performance and muscle mass in mice remains unknown. Here, we aimed to investigate, for the first time, the effects of 6′-SL on muscle functions. Seven-week-old male C57BL/6J mice were administered 100 mg/kg 6′-SL for 12 weeks, after which exhaustive treadmill performance, muscle strength, and muscle phenotype were examined. The administration of 6′-SL significantly improved exhaustive treadmill performance metrics, including distance and exhaustion time. Grip strength was also increased by 6′-SL administration. Additionally, 6′-SL increased muscle mass in both the gastrocnemius (GAS) and soleus. 6′-SL administration led to an increase in the minimum Feret’s diameter and the protein expression of total myosin heavy chain in the GAS muscle. In conclusion, 6′-SL administration in vivo led to increased running distance and time by increasing muscle mass and strength. These findings collectively indicate that 6′-SL is a potential agent for improving muscle health and exercise performance.

Adeno-associated viruses (AAV) are widely used as viral vectors for gene delivery in mammalian cells. We focused on the efficacy of transduction of AAV 2/5, 2/6, 2/8 and 2/9 expressing GFP in 3T3-L1 murine preadipocyte cells by live imaging microscopy using IncuCyte S3 and flow cytom-etry. Three transduction modes were assessed: AAV transduction in 3T3-L1 preadipocyte cells with or without further differentiation into mature adipocyte-like cells and injection of AAVs in differ-entiated adipocyte-like cells. AAV2/6 demonstrated the highest transduction efficiency in 3T3-L1 preadipocytes, as it was 1.5–2-fold more effective than AAV2/5, and AAV2/8 in the range of viral concentrations from 2×104 to 1,6×105 VG/cell. AAV2/5 and AAV2/8 showed transduction effi-ciencies similar to each other. The expression of GFP under the CMV promoter remained stable for up to 20 days. The induction of 3T3-L1 differentiation in three days after AAV transduction did not alter the GFP expression level, and AAV2/6 showed the best transduction efficiency. AAV2/6 demonstrated the ability to transduce mature adipocytes. These results were confirmed by in vivo studies on C57BL6 mice AAV2/6 had the highest transducing activity on both inguinal and inter-scapular adipose tissue. Thus, AAV2/6 has demonstrated higher transduction efficacy compared to AAV2/5, AAV2/8 and AAV2/9 both in 3T3-L1 adipocytes and adipose tissue in vivo, which proves its usability along with AAV8 and AAV9 for gene delivery to adipocytes.

This paper presents an interpretable support vector machine (SVM) and its application to rehabilitation assessment. We introduce the concept of nearest boundary point to standardize the one-class SVM decision function and determine the shortest path for data from abnormal cases to become those from normal cases. This analytical approach is computationally simple and provides a unique solution. The nearest boundary point of abnormal data can also be used to analyze the cause of abnormal classification and indicate countermeasures for normalization. These properties render the proposed interpretable SVM valuable for medical assessment applications and other problems that require careful consideration of classification results for treatment. Simulation and application results demonstrate the feasibility and effectiveness of the proposed method.

The conformity assessment of products or a measured value with the given standards is carried out based on the global risk of producers and consumers calculation. A product may conform to specifications but be falsely rejected as non-conforming. This is about the producer's risk. If a product doesn't meet the requirements but is falsely accepted as conforming, that poses a risk to the consumer. The conventional approach to risk assessment, which yields only a single numerical value for the global risk of producers and consumers, is naturally extended, and utilized for assessing risk in measurement models with linear regression. The outcomes of the two-dimensional extension, along a moderate scale, are the parabolas with an opening upwards. Risk surfaces were obtained through three-dimensional extension over the area limited by the moderate scale and guard band axes. Four models with different ranges of tolerance intervals were used to test this innovative method of risk assessment in linear regression. The corresponding standard measurement uncertainties are determined by applying a simplified measurement model with the use of comprehensive data on the measurement performance and by determining measurement uncertainty derived from consideration of the functional relationship obtained by linear regression analysis. Models that utilize information from linear regression analysis to determine measurement uncertainty are biased towards risks at the edges of the moderate scale. Testing the model's performances with metrics related to the confusion matrix, such as the F1 score, further substantiated this assertion. The diagnostic odds ratio has been proven to be extremely effective in identifying the curve along the guard band axis, along which the global risks of producers and consumers are at their lowest.

Butirosins are naturally occurring aminoglycoside (AG) antibiotics featuring a 4,5-disubstituted 2-deoxystreptamine (2-DOS) with a (2S)-4-amino-2-hydroxybutyrate (AHBA) side chain. This side chain has been shown to confer resistance against AG modifying enzymes, leading to ongoing studies on the butirosin biosynthetic pathway and the corresponding enzymes. Butirosin is produced by Niallia (formerly Bacillus) circulans and Bacillus vitellinus, with most research focused on the former strain. To date, no whole genome analysis has been performed on B. vitellinus. In this study, we sequenced the complete genome of B. vitellinus NBRC 13296 and performed a comparative analysis of different butirosin biosyntheric gene clusters (BGCs), including those from N. circulans. The complete genome of B. vitellinus NBRC 13296 comprises a 6,331,192 base circlular chromosome with a GC content of 52.68%. The annotation revealed the presence of 5,605 CDSs, 70 tRNA genes, 30 rRNA genes, and 3 ncRNA genes in NBRC 13296. The highest dDDH and ANI values between NBRC 13296 and the most closely related type strain, Paenibacillus chitinolyticus KCCM 41400, were 97.8% and 98.66%, respectively. Based on these genome-based comparative analyses, we propose reclassifying B. vitellinus NBRC 13296 as P. chitinolyticus. Genome mining revealed 18 gene clusters encoding the biosynthesis of diverse secondary metabolites in the genome of B. vitellinus NBRC 13296, indicating the enormous biosynthetic potential of this strain. The predicted structural diversity of secondary metabolites includes aminoglycoside, PKS, NRPS, PKS-NRPS hybrids, metallophores, phosphonates, terpenes, β-lactones, and RiPP peptides. We then comparatively characterized butorosin BGCs previously studied in several N. circulans strains. Additionally, comparative genome analysis revealed complete butirosin BGCs identified from P. chitinolyticus KCCM 41400, P. chitinolyticus NRRL B-23119, P. chitinolyticus NRRL B-23120, P. chitinolyticus B-14908, P. chitinolyticus YSY-3.1, P. chitinolyticus JMW06, Paenibacillus sp. GbtcB18, Paenibacillus sp. HGH0039, Paenibacillus sp. MZ04-78.2. Finally, we identified the core region consisting of BtrS, BtrN, BtrM, BtrL, BtrA, BtrB, BtrC, BtrD, BtrD, BtrE, BtrF, BtrG, BtrH, BtrI, BtrI, BtrJ, BtrK, BtrO, BtrP, and BtrV, followed by an upstream region organizing BtrQ, BtrW, BtrX, BtrY, and BtrZ in the same transcriptional direction and sequential genetic arrangement, and a downstream region organizing various proteins based on BtrT, BtrR2, BtrU, and BtrR1. Our study provided insights into the reclassification of B. vitellinus NBRC 13296 to P. chitinolyticus and suggested the need for continued studies on butirosin biosynthesis from an enzymatic perspective.

Pragmatic trials aim to assess intervention efficacy in usual patient care settings, contrasting with explanatory trials conducted under controlled conditions. In aging research, pragmatic trials are important designs for obtaining real-world evidence in elderly populations, which are often underrepresented in trials. In this review, we discuss statistical considerations from a frequentist approach for the design and analysis of pragmatic trials. When choosing the dependent variable, it is essential to use an outcome that is highly relevant to usual medical care while also providing sufficient statistical power. Besides traditionally used binary outcomes, ordinal outcomes can provide pragmatic answers with gains in statistical power. Cluster randomization requires careful consideration of sample size calculation and analysis methods, especially regarding missing data and outcome variables. Mixed effects models and generalized estimating equations (GEEs) are recommended for analysis to account for center effects, with tools available for sample size estimation. Multi-arm studies pose challenges in sample size calculation, requiring adjustment for design effects and consideration of multiple comparison correction methods. Secondary analyses are common but require caution due to the risk of reduced statistical power and false-discovery rates. Safety data collection methods should balance pragmatism and data quality. Overall, understanding statistical considerations is crucial for designing rigorous pragmatic trials that evaluate interventions in elderly populations under real-world conditions. In conclusion, this review focuses on various statistical topics of interest to those designing a pragmatic clinical trial, with consideration of aspects of relevance in the aging research field.

Concrete cracks and local damage can affect the bond performance between concrete and steel bars, thereby reducing the durability of reinforced concrete structures. Compared with general concrete crack repair methods, biomineralization repair not only has effective bonding capabilities but is also particularly environmentally friendly. In view of this, this study aimed to apply biomineralization technology to repair damaged fiber-reinforced lightweight aggregate concrete (LWAC). Two groups of LWAC specimens were prepared. The control group used lightweight aggregates (LWAs) without bacterial spores and nutrient sources, and the experimental group used LWAs containing bacterial spores and nutrient sources. These specimens were first subjected to compression tests and pull-out tests, respectively, and thus were damaged. After the damaged specimen healed itself in different ways for 28 days, secondary compression and pull-out tests were conducted. The self-healing method of the control group involved placing the specimens in an incubator. The experimental group was further divided into experimental group I and experimental group II. The self-healing method of experimental group I was the same as that of the control group. The self-healing method of experimental group II involved soaking the specimen in a mixed solution of urea and calcium acetate for two days, and then taking it out and placing it in an incubator for two days, with a cycle of four days. The test results showed that, compared with the control group specimens, the relative bond strength ratio of the experimental group II specimens increased by 17.9%. Moreover, the EDS and XRD analysis results confirmed that the precipitate formed at the crack was calcium carbonate, which improved the compressive strength and bond strength after self-healing. This indicates that the biomineralization maintenance method used in experimental group II is more effective.

Occupational accidents, despite continuous safety updates, are still a scourge in the occupational and forensic spheres, constituting, among other things, the subject of a large share of litigation. Demographic data can help to understand the areas where the application of health surveillance is lacking. This meta-analysis sets out to analyze data from studies on accidents at work, focusing on the correlation between the areas in which accidents occur and whether or not personal safety equipment is used, about the different regulations in force. For the selection of the data, a systematic review was carried out according to the PRISMA guidelines, with the primary objective of identifying the trend of occupational accidents in specific geographical areas, which differ in terms of the attention paid to preventive aspects. The data we highlighted showed, regarding the type of accident, substantial differences between low-income countries and industrialized countries (stratified according to the Human Development Index) and, an overall indifference as to whether or not individual safety devices were used, revealing that, despite the continuous normative evolution in the field of safety at work, even today, the investigative data on the actual application of the regulations, during accidents at work, is underestimated and little researched.

With the development of organizational biology and forced from the EU Cosmetic Regulation (EU/1223/2009) with the complete ban of animal testing for cosmetic purposes, 3D skin models have been widely developed due to their similar physiological structure and metabolic function to native human tissue. 3D skin models for in vitro cosmetic evaluation are still promising alternative methods for evaluating phototoxicity, corrosivity and irritation. These models have been used for early screening and later validation of toxicity and efficacy evaluation by many well-known cosmetic companies. 3D skin models have become an important tool in cosmetic evaluation research. This article reviews the development of 3D skin models and their application in cosmetic evaluation. An outlook on the current application and future technological development directions in the cosmetic field is also presented.

Photovoltaic (PV) technologies are developing rapidly as a result of their ability to reduce energy consumption from conventional sources as well as the growth of global energy expenditures. Nevertheless, several impact categories during the PV panel life cycle occur and some principal sectors are affected. These impact categories are assessed by applying life cycle analysis (LCA) techniques through various software programs, databases and methods. Such analyses of energy technologies are crucial, as they can reveal the occurrence of hazardous emissions at distinct life cycle stages. In the present paper, a PV panel impact assessment through life cycle analysis is carried out. More precisely, a combination of PV technologies—monocrystalline, multicrystalline, copper indium gallium selenide (CIGS), amorphous, and ribbon—is studied. The impact categories of ozone depletion, human toxicity, particulate matter, ionising radiation, photochemical ozone formation, acidification, eutrophication, and ecotoxicity, as well as the sectors of human health, ecosystem quality, and environment, are assessed using the openLCA software, the ecoinvent database, the eco-indicator 99, IMPACT 2002+, ReCiPe, and TRACI methods.

In this study, cement is used as the component that provides the stabilizing effect in order to evaluate the hardness and stability of loess soil. To assess the strength characteristics of loess soil reinforced with cement, samples were created with four different cement contents and three different curing times. The materials were put through a series of tests to determine their flexural strength, direct shear strength, indirect tensile strength, and unconfined compressive strength. An appropriate cement dosage was found, in addition to a durability index that could be used to quantify the effect of water absorption investigations on cement-stabilized loess. Both of these discoveries were made simultaneously. Analyses of investigations such as scanning electron microscopy (SEM) and energy dispersive X-ray fluorescence spectrometry (XRF) examinations were carried out so that the fundamental mechanics of the materials could be comprehended. According to the findings, the cohesion of cement-stabilized loess is significantly more sensitive to structure than the friction angle of the material, and the cohesion is responsible for the increase in shear strength after remolding. To get the desired level of strength, it is necessary to adjust the cement's proportions. In addition, as the curing period progresses, we see an increase in the cement-stabilized loess's resistance and stiffness. This is because of the interactions that take place between the structure and the mineral composition. It is believed that this event was caused by the cementation that occurs naturally. As a consequence of this reaction, the production of new cementitious materials takes place. The cation exchange that causes the hydration and pozzolanic reaction that leads to the creation of aggregates and interparticle flocculation is responsible for their production. These findings suggest that cement may be utilized as a simple and effective method of loess stabilization, which will ultimately result in improved performance of the loess.

The aim of this paper is to explore the watertightness behaviour for high pressure applications using Multijetfusion technology and polyamide 12 as a material. It reports an efficient solution for manufacturing functional prototypes and final parts for water pressure applications. It provides manufacturing rules to engineers in the pressurized product development process up to 10 MPa of nominal pressure. The research findings show manufacturers the possibility of using additive manufacturing as an alternative to traditional manufacturing. Water leakage was studied using different printing orientations and wall thickness for a range of pressure values. An industrial ball valve was printed and validated with the ISO 9393 standard also meeting tolerance requirements. This paper is a pioneering approach to the additive manufacturing of high performance fluid handling components. This approach solves the problem of leakage caused by porosity in additive manufacturing technologies

This research paper investigates the enhancement of strength and performance of self-compacting concrete (SCC) for integration in Department of Public Works and Highways (DPWH) projects using a value engineering approach. The study explores key elements of SCC's strength and performance, including mix design optimization, construction practices, and durability considerations. Strategies to optimize SCC's strength, durability, and workability are discussed, emphasizing the benefits of SCC in improving construction efficiency and quality control within DPW infrastructure. The study also identifies challenges and gaps in SCC utilization, such as standardized performance verification and cost considerations, and proposes future directions for advancing SCC technology in civil infrastructure development.

This study presents the core tenets that constitute culturally responsive science assessments (CRSciA) for K-12 education and aligned them with the capabilities of generative AI (GenAI). The tenets were identified based on their dominance in the literature, including Indigenous Language, Race and Ethnicity, Religious Beliefs, Family and Community, and Indigenous Knowledge. These tenets were instrumental in developing the GenAI-CRSciA framework and the subsequent prompts to generate CRSciAs aligned with the Next Generation Science Standards (NGSS) while comparing it with standard prompt strategies. The results showed that the GenAI-CRSciA approach outperformed standard prompting strategies in terms of generating CRSciAs, proving its effectiveness in addressing the ongoing challenges in science assessments. Even though the GenAI-CRSciA framework presented assessments that cover a range of the cultural backgrounds, it presents potential challenges such as compromising curricula core competencies and overgeneralization of students’ backgrounds; overlooking subcultural variations within a country or region, for example differences between urban and rural students, or between different ethnic or linguistic groups within the same nation, which can lead to bias and less effective CRSciA outputs. To address this, we recommend that teachers provide comprehensive and specific background information about their students when using the GenAI-CRSciA prompting, ensuring that the generated content is truly reflective of the students’ unique cultural contexts. In larger class settings, teachers could implement comprehensive local data indexing, where detailed student background information is uploaded and retrievable for use in crafting more personalized CRSciAs. We recommend educators make conscious efforts to validate the generated assessments with input from human experts, including community or family, educators, and even students who are knowledgeable about the cultural nuances. We also suggest continuous professional development would be necessary to enhance teachers’ understanding of the cultural tenets.

As Li-ion batteries use is spreading, incidents in large energy storage systems (stationary storage containers, …) or in large-scale cell and battery storages (warehouse, recyclers, …), often leading to fire, are occurring on regular basis. Water remains one of the most efficient fire extinguishing agents for tackling those battery incidents and large quantities are usually necessary. Since bat-teries contains various potentially harmful components (metals and their oxides or salts, sol-vents…) and that thermal runway induced battery incidents are accompanied with complex and potentially multistage fume emissions (containing both gas and particles) the potential impact of fire run-off water on the environment should be considered and assessed carefully. The tests presented in this paper focus on the analysis of the composition of run-off waters used to spray NMC Li-ion modules under thermal runaway. It highlights that waters used for fire-fighting are susceptible to contain many metals, including Ni, Mn, Co, Li and Al mixed with other carbonaceous species (soot, tarballs) and sometimes undecomposed solvents used in the elec-trolyte. Extra-polation of pollutant concentrations compared with PNEC values showed that, for large scale incidents, run-off water could be potentially hazardous to the environment.

Despite ongoing efforts, the relationship between groin strength and injury remains unclear. The challenge of accurately predicting injuries presents an opportunity for researchers to develop pre-vention strategies to reduce the occurrence of such injuries. Consequently, this issue requires further investigation to obtain insights into effective mitigation strategies. In 120 male soccer players the maximum isometric strength of the hip muscle groups was measured, and the strength ratios were calculated. Previous injury and anthropometric data were registered. Injury data were collected following the FIFA/UEFA consensus. The K- Nearest Neighbour (k-NN), was used to predict the incidence of injury, while the significant predictive variables of the k-NN algorithm were fitted into a multivariate logistic regression model (LR) to analyze the likelihood of players sustaining a groin injury. The LR model determined two variables as significant predictors of groin injury. Players were less likely to sustain a groin injury by 76% for each decrease of the Adductors/Abductors isometric strength ratio in the non-dominant limb (OR = 0.238, CI 95%= [(0.098-0.572]). Players with a history of previous injury had a 67% greater risk of sustaining an injury (OR = 0.333, CI 95%= [(0.1068-1.038]). Isometric hip adductor and abductor strength im-balances of the non-dominant lower limb and a history of previous injury were risk factors for groin injury in soccer players.

Drought affects human and natural systems, human and animal life and health, and socioeconomic activities. Drought consequences depend on its type and class, but also on the preparedness and resistance of communities to this climate disturbance. In the last decades, droughts accounted for about 16% of the total number of disasters but were responsible for 95% of the number of deaths and 26% of economic losses in Africa. This study aims to assess the drought regime in Southern Africa based on drought and vegetation indices. The SPI and SPEI were calculated at different timescales, using ERA5 data for the 1971 – 2020 period. The spatiotemporal distribution of drought descriptors was analyzed and compared with the patterns of the NDVI, EVI and VCI vegetation indices. The results reveal (i) the occurrence of droughts of various classes and at different timescales throughout the study period and region, (ii) high spatial variability in the number, duration, severity and intensity of drought, which tends to decrease with increasing timescale, (iii) high spatial-temporal agreement between drought and vegetation indices that confirm the dryness of vegetation during drought. These results aim to support policymakers in defining legislation to manage drought and water resources.

The objectives of the study were to determine the spatial rate of CO₂ flux (Net Ecosystem Exchange) and soil moisture in a wetland ecosystem applying Sentinel-1 IW (Interferometric Wide) data of VH (Vertical Transmit/Horizontal Receive—cross polarization) and VV (Vertical Transmit/Vertical Receive—like polarization) polarization. In-situ measurements of carbon flux, soil moisture, and LAI (Leaf Area Index) were carried out over the Biebrza Wetland in north-eastern Poland. The impact of soil moisture and LAI on backscattering coefficient (σ°) calculated from Sentinel-1 data showed that LAI dominates the influence on σ° when soil moisture is low. The models for soil moisture have been derived for wetland vegetation habitat types applying VH polarization (R² = 0.70 to 0.76). The vegetation habitats: reeds, sedge-moss, sedges, grass-herbs, and grass were classified using combined one Landsat 8 OLI (Operational Land Imager) and three TerraSAR-X (TSX) ScanSAR VV data. The model for the assessment of Net Ecosystem Exchange (NEE) has been developed based on the assumption that soil moisture and biomass represented by LAI have an influence on it. The σ° VH and σ° VV describe soil moisture and LAI, and have been the input to the NEE model. The model, created for classified habitats, is as follows: NEE = f (σ° Sentinel-1 VH, σ° Sentinel-1 VV). Reasonably good predictions of NEE have been achieved for classified habitats (R² = 0.51 to 0.58). The developed model has been used for mapping spatial and temporal distribution of NEE over Biebrza wetland habitat types. Eventually, emissions of CO₂ to the atmosphere (NEE positive) has been noted when soil moisture (SM) and biomass were low. This study demonstrates the importance of the capability of Sentinel-1 microwave data to calculate soil moisture and estimate NEE with all-weather acquisition conditions, offering an important advantage for frequent wetlands monitoring.

Strong yet ductile alloys have long been desired for industrial applications to enhance structural reliability. This work produced two (CoCrNi)93.5Al3Ti3C0.5 medium-entropy alloys with exceptional strength-ductility combinations, via short/medium (3 min/30 min)-time annealing after hot-rolling. Three types of intergranular precipitates including MC, M23C6 carbides, and L12 phase were detected in both the samples. Noticeably, the high density of intragranular L12 precipitates were only founded in the medium-time annealed sample but not in another one. Upon inspection of deformed substructure, it was revealed that the plane slip is the dominant deformation mechanism of both the alloys. This is related to the lower stacking fault energy, higher lattice friction induced by C solute, and slip plane softening caused by intragranular dense L12 precipitates. Additionally, we noted that the stacking fault and twinning act as the mediated mechanisms in deformation of the short-time annealed alloy, while only the former in the medium-time annealed one. It is attributed to the higher energy stacking faults and the increased critical twinning stress caused by intragranular dense L12 precipitates that inhibited the twinning tendency. Our present findings provide not only a guidance for optimizing the mechanical properties of high/medium-entropy alloys, but also a fundamental understanding of deformation mechanisms.

This study explores novel techniques to improve the detection accuracy of skarn iron deposits using advanced image processing methodologies. Leveraging the capabilities of Aster image, Band Ratio (BR) images, and Principal Component Analysis (PCA), alongside the power of 3D Convolutional Neural Networks (3D-CNN), the research aims to enhance the precision and efficiency of ore detection in complex geological environments. The proposed method employs a specific 3D-CNN architecture, accepting input as a 7×7×C image patch, where C represents the combined number of selected Aster image bands, Principal Component (PC) bands, and computed BR images. To evaluate the accuracy of the proposed method, five distinct image bands combinations, including the proposed bands combination, were tested and evaluated based on the overall accuracy (OA), average accuracy (AA), and kappa coefficient. The results demonstrated that while the incorporation of BR images alongside Aster bands initially seemed promising, it introduced significant confusion in certain classifications, leading to unexpected mis-classification rates. Surprisingly, utilizing solely Aster bands as input parameters yielded higher accuracy rates (OA= 93.13%, AA = 91.96%, Kappa = 90.91%) compared to scenarios involving the integration with band ratios (OA = 87.02%, AA = 79.15, and Kappa = 82.60%) or the integration of BR images to PC bands (OA= 87.78%, AA = 82.39%, Kappa = 83.81%). However, the amalgamation of Aster bands with selected PC bands showed slight improvements in accuracy (OA= 94.65%, AA = 92.93%, Kappa = 93.45%), although challenges in accurately classifying certain features persisted. Ultimately, the proposed combination of Aster bands, PC bands, and BR images (proposed bands combination) presented the most visually appealing and statistically accurate results (OA = 96.95%, AA= 94.87%, and Kappa = 95.93%), effectively addressing misclassifications observed in the other combinations. These findings underscore the synergistic contributions of each of the Aster bands, PC bands, and BR images, with Aster bands proving pivotal for optimal skarn classification, PC bands enhancing intrusions classification accuracy, and BR images strengthening wall rock classification accuracy. In conclusion, the proposed combination of input image bands emerges as a robust and comprehensive methodology, demonstrating unparalleled accuracy in the remote sensing detection of skarn iron minerals.

Faced with increasing climate challenges, this pioneering study introduces groundbreaking approaches to ensure the resilience of potato crops in east-central Poland. Our research aimed to develop an innovative, cost-effective system tailored to the diverse local conditions of this region. Conducted between 2018 and 2020, the study analyzed integrated and organic production systems across different soil types and potato varieties. The experiment was conducted using a randomized block design with three replications in two locations. Integrated practices, enhanced by mineral fertilization and chemical protection, notably delayed the onset of late blight by 16 days and extended the critical infection period by 17% compared to their organic counterparts. Remarkably, the integrated systems resulted in a 49% increase in total production and a 52% increase in commercial yields, demonstrating their effectiveness in enhancing crop resilience. Different potato varieties exhibit varied responses to cultivation systems, influencing both yield and disease resistance. Further investigation into these varietal responses can help optimize cultivation practices, leading to improved efficiency and sustainability in potato farming. Location and soil conditions have a significant impact on potato yield and the spread of potato blight. Further research into specific soil properties and the adaptation of varieties to local conditions can contribute to increased productivity and stability in potato production. This study not only paves the way towards sustainable agriculture but also highlights the crucial role of soil diversity in shaping resilient farming practices.

Ultrasound, as mechanical waves with frequencies exceeding 20 thousand hertz, has found wide applications in medicine, physiotherapy, and more recently in agriculture. This study aimed to investigate the impact of ultrasound on potato yield and its parameters, particularly on seed potato yield, quantity, mass, and multiplication coefficient of potato tubers. The research was based on a three-year field experiment, utilizing the randomized block design in a split-split-plot arrangement, in the central-eastern region of Poland. The primary factor were technologies: a) technology with employing ultrasonic pre-planting treatment, b) traditional cultivation without this treatment. The secondary factors were potato varieties. Sonication of tubers was conducted using a bath-type ultrasonic device equipped with piezoe-lectric transducers. Results revealed a significant influence of cultivation technology, cultivar, and weather conditions on seed tubers yield, quantity, and multiplication coefficient of potato tubers. However, genetic traits of the examined varieties and random factors significantly affected the individual seed tuber mass and the number of shoots emerging from a single tuber. Future Outlook: Future research could focus on further optimizing ultrasound application techniques in potato cultivation, considering diverse varieties and environmental conditions. Additionally, it would be worthwhile to analyze the long-term effects of ultrasound on tuber seed potato quality and their ability to adapt to changing climatic and soil conditions. Furthermore, studies investi-gating the impact of ultrasound on other plant species could broaden our understanding of po-tential benefits in agriculture.

A review of quantitative risk assessment (QRA) models of L. monocytogenes in produce was carried out, with the objective of appraising and contrasting the effectiveness of the control strategies placed along the food chains. Despite nine of the thirteen QRA models recovered focused on fresh or RTE leafy greens, none of them represented important factors or sources of contamination in the primary production, such as type of cultivation, water, fertilisers or irrigation method/practices. Cross-contamination at processing and during consumer’s handling was modelled using transfer rates, which were shown to moderately drive the final risk of listeriosis; highlighting therefore the importance of accurately representing the transfer coefficient parameters. Many QRA models coincided in the fact that temperature fluctuations at retail or temperature abuse at home were key factors contributing to increasing the risk of listeriosis. In addition to a primary module that could help assess current on-farm practices and potential control measures, future QRA models for minimally-processed produce should also contain a refined sanitisation module able to estimate the effectiveness of various sanitisers as a function of type, concentration and exposure time. Finally, L. monocytogenes growth in the products down the supply chain should be estimated by using realistic time-temperature trajectories, and validated microbial kinetic parameters, both of them currently available in the literature.

Extreme climates such as droughts and hot extremes, may result in marked damage to crop yields and threaten regional and global food security. Maize is a major grain crop in Liaoning Province, severely affected by drought and hot events. The objective of this study is to advance an approach to estimate the risk of crop yield reduction under the compound dry-hot events (CDHE) in Liaoning Province. Results show that the ratio of stations experiencing compound dry-hot events during the twelfth leaf and maturity stage tended to increase on the time scale. On a spatial scale, the frequency of compound dry-hot events in central Liaoning Province was relatively low during the whole and various reproductive periods of maize. In addition to the twelfth leaf, western Liaoning Province is prone to compound dry-hot events. The high-risk area for the occurrence of the compound dry-hot events in maize is Chaoyang City, located in the western part of Liaoning Province, and the cities in the low-risk area account for about 64.3% of the total number of cities in Liaoning Province, mainly in the central and northern parts of Liaoning Province. Generally, this study emphasizes focusing on the impacts of compound dry-hot events on agricultural production and provides an index to assess the risk of compound dry-hot events on maize production.

In the ongoing shift towards electric vehicles (EVs) primarily utilizing lithium-ion battery technology, a significant population of hybrid electric vehicles (HEVs) remains operational, reliant on established NiMH battery systems. Over the last twenty years, these HEVs have generated a substantial quantity of NiMH batteries that are either inoperable, experiencing performance degradation, or approaching the end of their service life. This results in a twofold challenge: a growing volume of environmentally hazardous waste due to the difficulty of NiMH battery reclamation, and escalating maintenance costs for HEV owners necessitated by replacement battery purchases. Patent WO2015092107A1, published in 2015, proposed a "Method for regenerating NiMh batteries." This method claims the ability to restore NiMH batteries to their original functionality. However, a comprehensive review of relevant scientific literature fails to identify any empirical evidence supporting the efficacy of the regeneration technique detailed in the patent. Within this context, this paper presents a detailed analysis and evaluation of the feasibility of the aforementioned patented method. To achieve this objective, the authors propose a prototype constructed utilizing NiMH battery cells sourced from a Toyota Prius. The experimental results obtained from this prototype demonstrate the potential for battery regeneration using the proposed method. These findings offer a promising solution for mitigating the challenges associated with NiMH battery disposal and maintenance within the HEV domain.

High-wind structures were identified in the Cross-Calibrated Multi-Platform (CCMP) ocean wind vector reanalysis for comparison with winds measured by satellite radiometers and synthetical aperture radar (SAR) instruments from February to October 2023. The comparison aims to evaluate bias, uncertainty, and spatial correlations with the goal of enhancing the accuracy of ocean wind datasets during tropical cyclones (TCs). In 10°longitude×10°latitude blocks, each containing a TC, Soil Moisture Active Passive (SMAP) and Advanced Microwave Scanning Radiometer 2 (AMSR2) winds are 6.5% and 4.8% higher than CCMP, while Advanced Scatterometer (ASCATB) is 0.8% lower. For extratropical cyclones, AMSR2 and SMAP also show stronger winds with a 5% difference, and ASCATB is about 0.3% weaker compared to CCMP. The comparison between SAR and CCMP for TC winds, sampled at the locations and time frames of SAR tiles, indicates that SAR winds around TCs are about 9% higher than CCMP winds. Using empirically defined TC structural indices, we find that the TCs observed by CCMP are shifted in locations and lack a compact core region. A Random Forest (RF) regressor was applied to TCs in CCMP with corresponding SAR observations, nearly correcting the full magnitude of low bias in CCMP statistically, with a 15m/s correction in the core region. The hierarchy of importance among the predictors is as follows: CCMP wind speed (62%), distance of SAR pixels to the eye region (21%) and eye center (7%), and distance of CCMP pixels to the eye region (5%) and eye center.

Oilseed plants of the Brassicaceae plant family are cultivated for food, feed and industrial purposes on large-scale in Europe. This review gives an overview of current market-oriented applications of new genomic techniques (NGTs) in relevant Brassicaceae oilseed crops based on a literature survey. In this respect, changes in oil quality, yield, growth and resistance to biotic and abiotic stress are goals in oilseed rape (B. napus) and camelina (C. sativa). Environmental risk assessment scenarios are developed for specific NGT applications in Brassicaceae oilseed crops with either a changed oil composition or with fitness related traits. In case of a changed oil composition an increase or decrease of polyunsaturated fatty acids (PUFA) demonstrates risks for health and survival of pollinators. In case of fitness related traits other risks were identified, i. e. an increased risk of spread and persistence of NGT plants. Furthermore, there are indications for potential disturbance of interactions with the environment, involving signalling pathways and reaction to stress conditions. It is shown that for a comprehensive risk assessment the technological potential of NGTs, the plants’ biology and the scale of releases have to be considered in combination. Therefore, the release of NGT plants into the environment for agricultural purposes will require risk assessment and monitoring of single traits as well as of combinatorial and long-term cumulative effects. In addition, risk management should develop concepts and measures to control and potentially restrict the scale of releases. This is especially relevant for NGT Brassicaceae in Europe which is a centre of diversity of this plant family.

Drug-induced liver injury (DILI) stands as a significant cause of drug attrition. To mitigate clinical DILI risks, assessing drugs using human liver models is crucial since animal studies may fall short due to species-specific liver pathway variations. Cell-based preclinical hepatotoxicity testing is often pertinent. In the present study, cells from a human liver cancer line (HepG2, HepaRG) were cultured in both formats of 2D and 3D spheroids to explore their responses to drugs. Liver-specific marker expressions across cell lines and culture formats were also examined to assess disparities in drug-induced liver injury marker expressions. In cytotoxicity assays, HepG2 cells exhibited heightened sensitivity to amiodarone HCl, while HepaRG cells showed greater sensitivity to acetaminophen. Generally, 2D cultures were more responsive to drugs than 3D cultures. Consistency was observed between cytotoxicity assays and liver injury markers AST and ALT. Variations were also noted in liver cell marker secretion, with albumin and urea concentrations declining post-drug treatment, particularly with higher baseline expression in HepaRG cells and 3D cultures. Additionally, mRNA expression levels of CYP enzymes involved in hepatocellular drug metabolism were compared following treatment with enzyme inducers. CYP1A2 and CYP2C9 were not expressed in HepG2 cells. On the other hand, CYP3A4 was expressed higher in 3D culture than in 2D culture. HepaRG cells exhibited significantly increased expression of all three enzymes post-treatment. Notably, enzyme expression was notably higher in 3D cultures than in 2D cultures. Collectively, these findings suggest that HepaRG cells and 3D cultures hold promise for evaluating DILI during early-stage drug development.

This study aims to investigate the microphysical properties of Arctic, tropospheric aerosol in the transition from the Arctic Haze in spring towards the summer season in 2021. A special focus lies on the hygroscopicity of the aerosol. Therefore, a one-parameter growth curve model is applied to lidar data from the Koldewey Aerosol Raman Lidar (AWIPEV in Ny-Ålesund, Svalbard) and simultaneous radiosonde measurements. Hygroscopic growth depends on different factors like aerosol diameter and chemical composition. To detangle this dependency, three trends in hygroscopicity are additionally investigated by classifying the aerosol first by its color ratio, and then by its season and altitude. Furthermore, two special days are discussed using Mie-theory. They show on the one side the complexity of analyzing hygroscopic growth by means of lidar data, but on the other side demonstrate that it is in fact measurable with this approach. For these two case studies we calculated, that the aerosol effective radius increased from 0.16 μm (dry) to 0.18 μm (wet), and from 0.28 μm to 0.32 μm for the second case. Generally, we found two different modes of stronger or weaker hygroscopic particles and a complex altitude dependence with the least hygroscopic particles in the middle free troposphere.

With increasing air and sea temperatures, the thermodynamic environments over the oceans become more favourable for the development of intense tropical cyclones (TCs) with rapid intensification (RI). In fact, the number of TCs undergoing RI is rising (Zhao, et al., 2018; Bhatia, et al., 2019; Song, et al., 2020; Hong & Wu, 2021; Liu, et al., 2022). RI over coastal sea areas before landfalling is particularly impactful and threatening to coastal lives and properties. There have been studies showing that offshore areas within 400 km of the coastline have experienced a significant increase in RI events with the count tripling from 1980 to 2020 (Li et al., 2023). The south China coastal region consists of highly densely populated cities especially the Pearl River Delta (PRD) region. Intense TCs maintaining its strength or RI of TCs close to the coastal region presents substantial forecasting challenges. This study investigates the effect of sea surface and subsurface temperature and salinity on the intensification of five TCs, namely Super Typhoons Hato in 2017 and Mangkhut in 2018, Typhoon Talim, Super Typhoon Saola and Severe Typhoon Koinu in 2023, which significantly affected the south China coastal region and triggered high TC warning signals in Hong Kong. The analysis utilized the Hong Kong Observatory (HKO) TC track and intensity data, along with the sea temperature and salinity profiles generated using the China Ocean ReAnalysis version 2 (CORA2) of the National Marine Data and Information Service (NMDIS) of China. While high sea surface temperature (SST) of 30°C or above, low surface sea surface salinity (SSS) of 34 psu or below, and strong salinity stratification of at least 0.8 psu per 100 m depth may offer useful hints for predicting RI, they are part of a broader set of contributing factors. This study represents the initial documentation of sub-surface salinity's impact on intense TCs over the South China Sea (SCS) in recent years and will encourage further research to refine forecasting RI of TCs before making landfall near PRD taking into account the effect of freshwater from the Pearl River.

The treatment, disposal, and resource utilization of waste mud are challenges for engineering construction. This study investigates the road performance of waste mud–solidified soil and reveals the mechanism of how solidifying materials influence the strength and deformation characteristics of waste mud. Waste mud, collected from a highway reconstruction project, was mixed with ordinary Portland cement as a solidifying material. Unconfined compressive strength tests, consolidated undrained triaxial shear tests, resonant column tests, and consolidation compression tests were conducted to evaluate the solidification effect. The test results show that with an increase in cement content from 5% to 9%, the unconfined compressive strength of the waste mud–solidified soil increased by over 100%, the curing time was extended from 3 days to 28 days, and the unconfined compressive strength increased by approximately 70%. However, an increase in initial water content from 40% to 60% reduced the unconfined compressive strength by 50%. With the increase of cement content from 5% to 9%, the cohesion and friction angles increased by approximately 78% and 24%, respectively. The initial shear modulus under dynamic shear increased by approximately 38% and the shear strain corresponding to a damping ratio decay to 70% of the initial shear modulus decreased by nearly 11%. The compression coefficient decreased by approximately 55%. Scanning electron microscopy and X-ray diffraction tests showed that a higher cement content led to the formation of more hydration reaction products, especially an increase in the content of AlPO4. The bonding material between soil particles significantly increased, exerting a bonding and filling effect on soil particles and firmly adhering them together. Consequently, the strength of the waste mud–solidified soil increased significantly while its compressibility decreased.

Such rapidly changing external conditions as the COVID-19 pandemic and the war in Ukraine, being pure crisis phenomena, not only determine the geopolitical and geoeconomic situation on the global markets, but also cause structural changes in individual countries. Under these conditions, the level of food self-sufficiency becomes particularly important, as it is one of the factors determining the food security of any country. The aim of the research is to assess Ukraine's food self-sufficiency compared to the European Union and Poland. The self-sufficiency ratio (SSR) index was used to assess food self-sufficiency. This is the ratio of the volume of production of the most important products of plant and animal origin to the volume of domestic consumption. Domestic consumption was defined as the volume of domestic production increased by the volume of imports, reduced by the volume of exports and also included changes in domestic stock levels. The surveyed time frame is 2019–2021. The analyzed data were taken from the State Statistics Service of Ukraine, FAOSTAT, USDA and Statistics Poland. A comparative analysis of self-sufficiency for the main agri-food sectors of Ukraine, the EU, and Poland showed significant differences. Taking into account the production potential and food self-sufficiency indicators of Ukraine, Ukraine's possible accession to the EU can be expected to have a major impact on the EU's supply and demand situation, as it may pose a threat to many EU agri-food sectors.

Abstract: Nordic exercises aim to improve physical abilities and prevent injuries; However, it is not clear in what type of sports modalities to use it, so this study arises from the interest of ana-lyzing its effect in different sports modalities. Objective: To analyze Nordic exercises effects on the lower limbs, and their relationship with the explosive and absolute strength inherent to demands of different sports modalities (football, athletics, basketball, sport climbing, cycling and taekwondo). Method: quasi-experimental research, identifying 122 athletes (18±3 years old) from: football (n=24), athletics/speed (n=20), sport climbing (n=20), basketball (n=24), taekwondo (n=14) and cycling (n=20); classified into a control group CG (n=57) and an experimental group EG (n=65). Results: dominant absolute strength of the initial (12.4±0.51) and final (14.5±0.98) EG, in greater proportion in basketball (P= < 0.05); explosive strength of the initial (42.4±1.2) and final (45.8±1.5) EG, with a significant difference in all modalities between before and after (p≤0.05), except in cy-cling and taekwondo; no major changes were found in the GC. Conclusion: Nordic exercises are recommended as part of training to improve levels of explosive strength with emphasis on the modalities of football, basketball, athletics/speed and sport climbing, being applicable to increase absolute strength in basketball.

This paper presents a particular tunneling method or new Austrian tunneling method (NATM) which plays an important role in reducing the subsidence of the Earth surface and the damage to the structures in urban areas. It has a wide range of applications in shallow tunneling projects all over the world. In this study, numerical modeling of third-line Metro tunnel in Tehran is under discussion which is designed and stabilized by NATM. The foregoing tunnel is excavated manually with a one-meter advancing step. In this project, the constructors used a lattice girder and sprayed concrete with 31 cm thickness as the initial lining. A suitable numerical software for this modeling is Plaxis 3D tunnel, which allows performing high-resolution finite element modeling (FEM) of the studied object. The performance of this method is investigated and compared with other NATM methods. As a result of numerical modeling, we give a value of 30.01 mm earth subsidence in the most damaged area of the settlement, in comparing with that of earth surface monitoring, which confirmed it with a dramatically low difference. Moreover, this tunnel was drilled and excavated with various methods, among which the less settlement has obtained by the proposed method. The results are promising to continue the tunneling with this method to expand the subway line in the city.

Aluminum wire is a common material for wire bonding due to its resistance to oxidation and low price. It does not melt when becoming a free air ball (FAB) during the electronic flame-off (EFO) process with wettability, and is applied by wedge bonding. This study used 20μm Zn-Coated Al-0.5wt.%Si (ZAS) wires to improve the FAB shape after the EFO process, while maintaining stability of the mechanical properties, including the interface bonding strength and hardness. In order to test circuit stability after ball bonding, the current-tensile test was performed. During the experiment, it was found that 80nm ZAS with wire bonding has lower resistance and higher fusing current. For the bias tensile test, the thicker Zn film diffused into the Al-Si matrix easily, after which the strength was reduced. The ball-bond interfaces had no change in their condition before and after the bias. Accordingly, ZAS could be a promising candidate for ball bonding in the future.

The backwater lowland habitats of large rivers, like the Mississippi River in North America, present complex often inaccessible environments for traditional capture-based fish biodiversity sampling. Our knowledge of the assemblages of fishes that occupy such habitats are often incomplete, and this can compromise management efforts. We employed environmental DNA (eDNA) metabarcoding methods to sample a Mississippi River bottom wetland system to assess ichthyofaunal diversity, and assemblage structure across habitat types, and we compared our results to capture-based survey records for the same habitats. We collected water samples in spring and fall of 2022 from slough, ditch, shallow lake and bayou habitats that varied in depth, vegetation, seasonal variability, and connectivity to the Mississippi River channel. We detected a diverse array of fish species that included 51 taxa. Nearly all species previously documented in the habitats were detected by eDNA metabarcoding, and we increased the number of documented species by more than a third. Most of the species were ubiquitous across the range of habitats, but there was also substantial assemblage structure, with some species exhibiting clear habitat specificity. Fall sampling was limited to the deeper bayou habitats where seasonal variation between spring and fall was minimal. eDNA metabarcode sampling was demonstrated to be effective at detecting invasive species as well as uncommon species, which included several species of conservation concern.

Alzheimer’s disease (AD) is an age-associated neurodegenerative disorder. A wealth of evidence indicates that the amyloid β (Aβ) aggregates result from dyshomeostasis between Aβ production and clearance, which plays a pivotal role in the pathogenesis of AD. Consequently, therapies targeting Aβ reduction represent a promising strategy of AD intervention. Tetramethylpyrazine nitrone (TBN) is a novel tetramethylpyrazine derivative with the potential for the treatment of AD. Previously, we demonstrated that TBN markedly improved cognitive functions and reduced Aβ, APP, BACE 1 and hyperphosphorylated tau levels in 3 × Tg-AD mice. However, the mechanism by which TBN inhibits Aβ deposition still unclear. In this study, we employed the APP/PS1 mice treated with TBN (60 mg/kg, ig, bid) for six months and N2a/APP695swe cells treated with TBN (300 μM) to explore the mechanism of TBN on the Aβ reduction. Our results indicated that TBN significantly alleviated cognitive impairment and reduced Aβ depositions in APP/PS1 mice. Further investigation of the underlying mechanisms revealed that TBN decreased the expression of APP and BACE1, activated the AMPK/mTOR/ULK1 autophagy pathway and inhibited the PI3K/AKT/mTOR/ULK1 autophagy pathway, as well as decreased the phosphorylation levels of JNK and ERK in APP/PS1 mice. Moreover, TBN was found to significantly reduce the mRNA levels of APP and BACE1, as well as those of SP1, CTCF, TGF-β, and NF-κB, transcription factors involved in regulating gene expression. Additionally, TBN was observed to decrease the level of miR-346 and increase the levels of miR-147 and miR-106a in the N2a/APP695swe cells. These findings indicate that TBN may reduce Aβ levels likely via reducing APP expression by regulating APP gene transcriptional factors and miRNAs, reducing BACE1 expression, and promoting autophagy activities.

This paper aims to develop a hierarchical risk assessment model using the newly-developed evidential reasoning (ER) rule, which constitutes a generic conjunctive probabilistic reasoning process. In this paper, we first provide a brief introduction to the basics of the ER rule and emphasize the strengths for representing and aggregating uncertain information from multiple experts and sources. Further, we discuss the key steps of developing the hierarchical risk assessment framework systematically, including (1) formulation of risk assessment hierarchy, (2) representation of both qualitative and quantitative information, (3) elicitation of attribute weights and information reliabilities, (4) aggregation of assessment information using the ER rule and (5) quantification and ranking of risks using utility-based transformation. The proposed hierarchical risk assessment framework can potentially be implemented to various complex and uncertain systems. A case study on the fire/explosion risk assessment of marine vessels demonstrates the applicability of the proposed risk assessment model.

Postbiotic is a preparation of inanimate microorganisms and/or their components that confers a health benefit on the host. Different bacterial strain and preparation method result in different functions. Herein, a postbiotic preparation named Postbiotic-P by intercepting 1-5 KD of the cell-free supernatants of L. caseiparacasei P6 fermentation broth was prepared, and its multifunctional activities were evaluated. The results showed that Postbiotic-P exerted good antihemolytic (10%-50% Postbiotic-P resulted in 4.9%-48.1% antihemolytic rate), anti-inflammatory (8% to 40% Postbiotic-P is comparable to 259.1-645.4 μg/mL of diclofenac sodium equivalents), antioxidant [reducing power (1.25%-12.5% Postbiotic-P resulted in the increase of OD700 from 0.279-2.322), DPPH free radical scavenging activity (2.5%-50% Postbiotic-P resulted in 38.9%-92.4% free radical scavenging rate), and hydroxyl radical scavenging activity (0.5%-4% Postbiotic-P resulted in 4.66%-10.38% hydroxyl radical scavenging rate)], and antimicrobial activities (against 2 Gram-positive, 8 Gram-negative and 1 fungus). Furthermore, it was proved that Postbiotic-P could significantly inhibit the increase of the peroxide value and the malondialdehyde content in cookies, indicating the application potential of Postbiotic-P in food preservation. Taken together, Postbiotic-P has good application potential for the development of health care products and functional foods. However, further studies are needed to determine their precise mechanism of action, to clarify the active components responsible for the function, and to validate the biological activities in animal models or clinical trials.

The effectiveness of combining strength-specific training with endurance training to enhance the performance of endurance runners remains uncertain. This study aimed to analyze effect of practising maximum-strength (MAX), explosive strength (EXP) or both combined (COMB) on seven runners’ performance-indicators: vertical jump (VJ), one-repetition-maximum-squat (1RM), peak-velocity/peak-running-speed (PV), lactate-threshold (over incremental-test-protocols, LT), middle-distance-time-trial (TT), maximum-oxygen-consumption (VO2max), running-economy (RE). Systematic-review (Scopus, Wed of Science, Sports Discuss, PubMed) with meta-analysis was conducted following PRISMA standards. Inclusion-criteria (PICOS) were: recreational or well-trained athletes aged 18-45 performing concurrent-training ≥five-week. Used search-terms were related to different types of strength/endurance, participants’ age, sport-modality. 20 manuscripts were selected, quality-assessed with PEDro. MAX training is more effective than EXP, COMB in improving VJ, 1RM, PV, while COMB is more effective than MAX, EXP to enhance TT. MAX is more effective than EXP in improving LT. Concurrent-workouts do not provide additional benefits to VO2max. It is unknown which strength-modality (MAX, EXP or COMB) is more effective in improving RE. Concurrent-training is more effective than single-mode-endurance-training for enhancing specific performance-variables in adult-endurance-runners. Middle-, long-distance-runners may consider incorporating MAX-training to target specific goals, e.g., improving VJ, 1RM, LT, PV while utilizing COMB-training to enhance TT. Certain variables may benefit from EXP. New randomized-controlled-trials are required to confirm these findings.

Background: Molecular genetic events are among the numerous factors affecting the clinical course of papillary thyroid carcinoma (PTC). Recent studies have demonstrated that aberrant expression of miRNA, as well as different thyroid-related genes, correlate with the aggressive clinical course of PTC and unfavorable treatment outcome, which opens up new avenues for using them in personalization of the treatment strategy for patients with PTC. In the present work, our goal was to assess the applicability of molecular markers in preoperative diagnosis of aggressive variants of papillary thyroid cancer. Methods: The molecular genetic profile (expression levels of 34 different markers and BRAF mutation) was studied for 108 cytology specimens collected by fine-needle aspiration biopsy in patients with PTC having different clinical manifestations. Results: Statistically significant differences with adjustment for multiple comparisons (p &lt; 0.0015) for clinically aggressive variants of PTC were obtained for four markers: miRNA-146b, miRNA-221, FN1, and CDKN2A. Weak statistical correlation (0.0015&lt; р&lt;0.05) was observed for miRNA-31, -375, -551b, -148b, -125b, mtDNA, CITED1, TPO, HMGA2, CLU, NIS, SERPINA1, TFF3, and TMPRSS4. Conclusions: The recurrence risk of papillary thyroid carcinoma can be preoperatively predicted using miRNA-221, the fibronectin and cyclin-dependent kinase inhibitor 2A genes.

The rise of fintech in the financial sector presents a transformative shift towards digitalization and sustainability, leveraging technologies like AI to minimize environmental footprint. Neobanks not only challenge traditional banking models but also offer innovative solutions that align with sustainable objectives. The purpose of this paper is to analyze the impact of neobanks on global sustainability, from economic, environmental, and social point of view. A comprehensive literature review of existing literature and current sustainable practices of neobanks was conducted. We have found that neobanks significantly positively contribute towards environmental sustainability with reduced paper use and logistics requirements of banking services. By offering more accessible and affordable banking services they importantly contribute towards higher financial inclusion, and with innovative products towards more competitive and innovative financial markets. AI-based tools they employ are increasing financial literacy and social inclusion. We also highlight concerns regarding electronic waste management, potential high energy consumption, required digital literacy and cybersecurity risks. We conclude that despite the mentioned risks, neobanks importantly contribute to global sustainability in many ways, and will even more in the future. Our findings can help neobanks shape sustainable practices and guide policymaking, as well as spread awareness of sustainable impact of banking services.

Background: Early diagnosis of postoperative complications is an urgent task, allowing timely prescribing of appropriate therapy and reducing the cost of patient treatment. Prognostic models based on various data could help in the early diagnosis of postoperative complications after cardiac surgery. Objectives: The purpose of the study was to determine whether an integrated approach based on clinical data along with metabolites and biomarkers had greater predictive value than the models built on less data. Methods: The study included patients (n=62) admitted for planned cardiac surgery (coronary artery bypass grafting with cardiopulmonary bypass), who were retrospectively divided into two groups depending on the presence (n=26) or absence (n=36) of postoperative complications of all types. Clinical and laboratory data on the first day after surgery were analyzed. Additionally, patients' blood samples were collected before and on the first day after surgery to determine biomarkers (interleukin-6, procalcitonin, NT-proBNP, high-sensitivity troponin T) and metabolites (8 aromatic and 2 dicarboxylic acids were detected using gas chromatography-mass spectrometry). Results: Patients before surgery, compared with healthy donors, differed in the concentration of metabolites (p &lt; 0.05), and had concentrations of a number of biomarkers exceeding the corresponding reference values. Multivariate PLS-DA models, predicting the presence or absence of postoperative complications, were built using clinical data (ROC-AUC=0.71), concentrations of metabolites and biomarkers (ROC-AUC=0.60), and the entire data set (ROC-AUC=0.75). For comparison we built univariate models using the EuroScore2 (ROC-AUC=0.59) and SOFA (ROC-AUC=0.76) scales; concentrations of lactate (ROC-AUC=0.71), the dynamic changes of 4-hydroxyphenyllactic acid (ROC-AUC=0.69), and the sum of three sepsis-associated metabolites (ROC-AUC=0.70). The proposed complex model using entire data set was comparable to the SOFA scale, which confirms the expediency of searching for new predictive models based on a variety of factors.

The resilience of towns and cities refers to their ability to adapt and recover when confronted with pressures or challenges. This study employs ten variables as indicators to assess the resilience of urban areas by analyzing official data and constructing a multilevel mixed-effects structural equation model. The empirical findings demonstrate that enhancing resilience significantly influ-ences urban service functions, such as strengthening healthcare systems, stabilizing the real estate market, and addressing socio-economic challenges. Specifically, factors such as healthcare re-sources, housing demand, population structure, and social security exhibit varying levels of resil-ience, which profoundly impact the spatial distribution of these factors and socio-economic de-velopment. Disparities in healthcare resource allocation, demographic aging trends, and shifts in the housing market closely correlate with resilience levels in different regions. Additionally, the study emphasizes that improving resilience not only boosts the reliability and security of urban services but also ensures that communities receive necessary support and protection during times of adversity. Consequently, policymakers should recognize the pivotal role of urban resilience in resource allocation and social equity, devising corresponding strategies to enhance the resilience of these areas.

Promoting the sustainable development of resource-based cities is of great significance to the ecological protection and high-quality development of the Yellow River Basin. Combining the environmental status and economic development, we objectively evaluate the ecological safety level of resource-based cities in the Yellow River Basin, compare and analysis the main factors affecting the ecological safety of different resource-based cities, and formulate precise and differentiated ecological safety protection measures in river basins to achieve high-quality development. Taking the Yellow River Basin as an example, this paper analyses the ecological level of the Yellow River Basin based on the theory of sustainable development, calculates the ecological safety level of 30 resource-based cities in the Yellow River Basin from 2006 to 2020 by TOPSIS model, and makes convergence analysis by classification. Through the DID empirical test of sustainable development planning policy on ecological safety factors, distinguish the development characteristics of different resource-based cities. The results show that: (1) the ecological safety level of resource-based cities in the Yellow River Basin is generally developing well, and there are differences among different types of resource-based cities; (2) the kinetic energy of sustainable development of resource-based cities in the Yellow River Basin is mainly industrial transformation, and the power of science and technology is insufficient; (3) local governments pay limited attention to environmental protection, and the sustainable development planning of resource-based cities in 2013 mainly promotes the adjustment of industrial structure of resource-based cities.