DIEP-based breast reconstruction necessitates wide undermining at the abdominal donor-site, creating large wound areas. Flap harvesting is usually conducted using electrosurgical dissection devices. This study sought to compare the clinical outcomes in patients after using the PEAK PlasmaBlade (PPB) versus monopolar electrocautery (MPE). This retrospective cohort study included 128 patients with DIEP-based breast reconstruction. Patient characteristics as well as information on the postoperative course were collected and a comparative evaluation was conducted. The MPE group exhibited significantly (p* = 0.0324) higher abdominal drainage volume (351.11 ± 185.96 ml) compared to the PPB group (279.38 ± 183.38 ml). Subgroup analysis demonstrated that PPB significantly reduced postoperative wound fluid in patients with BMI > 30 kg/m² (p* = 0.0284), without prior neoadjuvant chemotherapy (p** = 0.0041), and among non-smokers (p = 0.0046). Furthermore, postoperative pain was significantly (p**** < 0.0001) lower in the PPB cohort. This study confirms the non-inferiority of the PEAK PlasmaBlade to conventional electrocautery for abdominal flap harvesting. The PPB demonstrated advantages, notably reduced drainage volume and lower postoperative pain levels. Recognizing patient subsets that benefit more from the PPB highlights the importance of personalized device selection based on patient characteristics.

The urbanization effects on land surface phenology (LSP) have been investigated by many studies, but few studies focused on the temporal variations of urbanization effects on LSP. In this study, we used the MODIS EVI, MODIS LST data and China’s Land Use/Cover Datasets (CLUDs) to investigate the temporal variations of urban heat island intensity and urbanization effects on LSP in Northeast China during 2001–2015. Land surface temperature (LST) and phenology differences between urban and rural areas represented the urban heat island intensity and urbanization effects on LSP, respectively. Mann-kendall nonparametric test and Sen's slope were used to evaluating the trends of urbanization effects on LSP and urban heat island intensity. The results indicated that the average land surface phenology (LSP) during 2001–2015 was characterized by high spatial heterogeneity. The start of the growing season (SOS) in old urban area had become earlier and earlier than rural area and the differences of SOS between urbanized area and the rural area changed greatly during 2001–2015 (−0.79 days/year, p < 0.01). Meanwhile, the length of the growing season (LOS) in urban and adjacent areas had become increasingly longer than rural area especially in urbanized area (0.92 days/year, p < 0.01), but the differences of the end of the growing season (EOS) between urban and adjacent areas did not change significantly. Next, the UHII increased in spring and autumn during the whole study period. Moreover, the correlation analysis indicated that the increasing urban heat island intensity in spring contributed greatly to the increases of urbanization effects on SOS, but the increasing urban heat island intensity in autumn did not lead to the increases of urbanization effects on EOS in Northeast China.

Thin people who undergo implant insertion into the chest wall face a high risk of implant exposure to the external environment. Five months after an 8-year-old boy underwent implantable cardioverter-defibrillator (ICD) implantation in a subcutaneous pocket in the left anterolateral chest wall to manage long QT syndrome, ICD replacement became necessary owing to exposure risk from distal and lateral thinning of the ICD pocket. Pocket rupture and exposure would increase the risk of infection; therefore, we performed ICD removal and primary pocket closure. Two weeks later, a new suprafascial pocket was created, acellular dermal matrix (ADM) was attached to the inner wall to prevent ICD protrusion, and a new ICD was inserted. One year postoperatively, the ADM was engrafted, and no complications were observed. A thin subcutaneous layer increases the risk of ICD implantation complications. Inner wall strengthening with ADM can help prevent pocket rupture.

Monitoring and maintenance of cracked structures are generally done using structural integrity assessments. The plastic zone (PZ) crack path (CP) criteria state that a crack grows in the direction when the radius of the plastic zone ahead of the crack tip reaches a minimum value. The PZ can be evaluated using Stress intensity factors (SIF). The SIFs under mixed-mode loading were extracted from literature from three samples: two SENT samples made from polycarbonate and one modified C(T) sample made from low-carbon steel. In addition, the CP angle was evaluated for the W and R-criteria. It was found that both can predict the CP for lateral cracks in both tested materials and monotonic and cyclic load when the mode-mixity does not change considerably from one crack length to the next one or goes beyond 0.2. Moreover, the R-criterion exhibited an error as high as 1.7%, whereas the W-criterion showed a 6% error on the last crack length for the low carbon steel sample under cyclic load, which had a 100% increase in mode-mixity. Finally, the applicability of LEFM is checked, while the CP is sought by finding the size of the PZ.

Technological advancements in the Internet of Things (IoT), unmanned aerial vehicles (UAVs), and novel technological tools have transformed disaster management practices from localized approaches to a global framework. These innovations necessitate a unified understanding and application of diverse methodologies at an international level, ensuring they are accessible and operational across different sectors. This integration is crucial not only for technical personnel but also for medical teams, who play a pivotal role in disaster response and management. By fostering a comprehensive grasp of these methods, we can enhance coordination, efficiency, and effectiveness in addressing disasters on a global scale. The authors aimed to provide a comprehensive overview of emerging techniques that are driving shifts in strategic approaches and treatment technologies. Recognized as a domain of continuous research and development, this overview, by necessity, remains an incomplete snapshot of an evolving field. It highlights the dynamic nature of technological and strategic advancements, underscoring the importance of ongoing investigation and innovation to stay abreast of current trends and future directions. The article also highlights the importance of international collaboration beyond societal and national boundaries A single paragraph of about 200 words maximum. For research articles, abstracts should give a pertinent overview of the work. We strongly encourage authors to use the following style of structured abstracts, but without headings: (1) Background: Place the question addressed in a broad context and highlight the purpose of the study; (2) Methods: briefly describe the main methods or treatments applied; (3) Results: summarize the article’s main findings; (4) Conclusions: indicate the main conclusions or interpretations. The abstract should be an objective representation of the article and it must not contain results that are not presented and substantiated in the main text and should not exaggerate the main conclusions.

Background: Extracellular Vesicles are pivotal mediators in intercellular communication, facilitating the exchange of biological information among healthy, pathological and tumor cells. Between the diverse subtypes of extracellular vesicles, exosomes have unique properties, clinical and therapeutical applications, even towards cancer. Breast cancer ranks as one of the most prevalent malignancies across the globe. Both the tumor core and its surrounding microenvironment engage in a complex, orchestrated interaction that facilitates the cancer’s growth and spread. Methods: The most valuable and significant PubMed Literature about extracellular vesicles and adipose–derived stem cells exosomes was selected and analyzed in order to report their biological properties and potential applications, in particular on the Triple–Negative Breast Cancer. Results: Adipose–derived stem cells exosomes represent a potential tool to target the tumor core of the Triple–Negative Breast Cancer, its microenvironment and surrounding tissues including metastasis. The authors are developing a supportive Triple–Adipose–derived stem cells Exosomes [T.A.E.] Technology against breast cancer in order to perform a selective preconditioning of the cancer before or while the traditional oncological treatments are running. Conclusion: The possibility to exploit the impact of Adipose–derived stem cells exosomes within the T.A.E. Technology against the Triple–Negative breast cancer is real, highlighting a new era for supportive measures against breast cancer.Keywords: Extracellular vesicles; Exosomes; Adipose–derived stem cells, Tumor microenvironment, Triple–Negative Breast Cancer, T.A.E. Technology.

Channel bends are one of the most important characteristic features of natural streams. These bends often create the conditions for a hyporheic zone, which has been recognized as a critical component of stream ecosystems. The streambed vertical hydraulic conductivity (K_v), vertical hydraulic gradient (VHG) and Darcian flux (DF) in the hyporheic zone were estimated at 61 locations along a channel bend of the Beiluo River during July 2015 and January 2016. All the streambed attributes showed great spatial variability along the channel bend. Both upward fluxes and downward fluxes occurred during the two test periods, most of studied stream sections were controlled by downwelling, indicating stream water discharge into the subsurface. The average downward flux was higher at the downstream side than at the upstream side of the channel bend, especially in July 2015. The distribution of streambed sediment grain size has a significant influence on the variability of K_v; high percentages of silt and clay sediments generally lead to low K_v values. Higher K_v at the depositional left bank at the upstream site shifted toward the erosional right bank at the downstream site, with K_v values positively correlated with the water depth. This study suggested that the variabilities of K_v and VHG were influenced by the stream geomorphology and that the distribution of K_v was inversely related, to a certain extent, to the distribution of VHG across the channel bend. K_v and VHG were found to have opposite effects on the DF, and the close relationship between K_v and DF indicated that the water fluxes were mainly controlled by K_v.

This study investigates the effects of Zinc (4wt.%) and severe plastic deformation on the mechanical properties of AZ61 magnesium alloy through the stir-casting process. The severe plastic deformation (equal channel angular pressing (ECAP)) has been done followed by T4 heat treatment. The microstructural examinations revealed that the addition of 4wt.%Zn enhances the uniform distribution of β-phase, contributing to a more uniformly corroded surface in corrosive environments. Additionally, dynamic recrystallization (DRX) significantly reduces the grain size of as-cast alloys after undergoing ECAP. The attained mechanical properties demonstrate that after a single ECAP pass, AZ61 + 4wt.%Zn alloy exhibits optimal yield strength (YS), ultimate compression strength (UCS), and hardness. This research highlights the promising potential of AZ61 + 4wt.%Zn alloy for enhanced mechanical and corrosion-resistant properties, offering valuable insights for applications in diverse engineering fields.

In this review, we summarize recent progress in crystal growth and understanding the influence of crystal structure on the superconductivity in pure and Pb-doped Bi2Sr2CuOy (Bi-2201) materials belonging to the overdoped region of high temperature cuprate superconductors. The crystal growth of Bi-2201 superconductors faces challenges due to intricate materials chemistry and lack of knowledge of corresponding phase diagrams. Historically, a crucible-free floating zone method has emerged as the most promising growth approach for these materials, resulting in high-quality single crystals. This review outlines the described in the literature and the authors' synthesis endeavors, encompassing Pb-doped Bi-2201 crystals, detailed structural characterization of as-grown and post-growth annealed samples, and highlights optimal growth conditions that yield large-size, single-phase, and compositionally homogeneous Bi-2201 single crystals.

Sustainable manufacturing practices are becoming increasingly necessary due to the growing concerns regarding climate change and resource scarcity. Consequently, material recycling technologies have gradually become preferred over conventional processes. This study aimed to recycle waste polylactic acid (PLA) from household-disposed cups and lids to create 3D-printed parts and promote sustainable manufacturing practices. To achieve this, the current study utilised virgin and post-consumer PLA (sourced from household waste) blends. The PC-PLA wastes were shredded and sorted by size with the aid of a washing step, resulting in a filament with a 1.70 ± 0.5 mm diameter without fragmentation or dissolution. A 50:50 wt.% blend of virgin PLA (vPLA) and PC-PLA was selected as the standard recycling percentage based on previous research and resource conservation goals. The study investigated the impact of three 3D printing parameters (layer height (LH), infill density (I), and nozzle temperature (NT))on the quality of 3D-printed parts using a three-level L9 Taguchi orthogonal array. The findings revealed that blending PC-PLA with vPLA led to significant improvements in the tensile, flexural, and impact strengths by 18.40%, 8%, and 9.15%, respectively, compared to those of recycled PLA. This conclusion was supported by the investigation of the fracture surface area, which revealed fractographic features associated with printing parameters, such as plastic deformation and interfilament debonding. An ANOVA analysis revealed a positive influence of larger layer height and high nozzle temperature on the mechanical properties. Subsequently, the optimal printing parameters (LH: 0.3 mm, I: 100%, and NT: 215 °C) were determined using the S/N ratio, and a confirmation test using the optimum printing parameters exhibited a strong correlation with statistically predicted outcomes. Finally, the study used optimum printing parameters to fabricate 100% post-consumer recycled PLA 3D printed parts, demonstrating their potential for low-strength applications. Based on these findings, it can be concluded that virgin and post-consumer recycled PLA blended filament for fabricating 3D printed components is an effective way to support plastic recycling in the context of a circular economy.

Abstract. Graphene family (GF)-Calcium phosphate (CaP) composites, holds great potential as components of bone regeneration materials. GF nanomaterials can be modified physically as well as chemically, which are to be biomimetic, mechanically to be hard due to their capability to support exceptional mechanical, thermal and electronic properties. These biocompatible GF composites coated on the calcium phosphate can enhance and tolerate stem cell growth and differentiation, proliferation into various lineages or interact with bioorganisms. The development in CF-CaP materials and their physicochemical/biointeractions and strategies towards osteoblasts is a great concern to promote faster healing and reconstructions of large bone imperfections or defects. In this review, we explain the influence of the CF-CaP and summarize recent developments on designing CF-CaP architectures as multifunctional bone regeneration platforms. We have also explored the typical biological applications concerning these CF-CaP based bioactive nanocomposites. Furthermore, the future viewpoints and evolving challenges will also be emphasized. Due to the shortage of full-length reviews in this emerging research field, this review would be caught great attention and encourage various new chances across a wider range of disciplines.

Residual stress (RS) is the most challenging problem in metal additive manufacturing (AM) since the build-up of high tensile RS may influence the fatigue life, corrosion resistance, crack initiation, and failure of the additively manufactured components. While tensile RS is inherent in all the AM processes, fast and accurate prediction of stress state within the part is extremely valuable and would result in optimization of the process parameters in achieving a desired RS and control of the build process. This paper proposes a physics-based analytical model to rapidly and accurately predict the RS within the additively manufactured part. In this model, a transient moving point heat source (HS) is utilized to determine the temperature field. Due to the high temperature gradient within the proximity of the melt pool area, material experience high thermal stress. Thermal stress is calculated by combining three sources of stresses known as stresses due to the body forces, normal tension, and hydrostatic stress in a homogeneous semi-infinite medium. The thermal stress determines the RS state within the part. Consequently, by taking the thermal stress history as an input, both the in-plane and out of plane RS distributions are found from incremental plasticity and kinematic hardening behavior of the metal by considering volume conservation in plastic deformation in coupling with the equilibrium and compatibility conditions. In this modeling, material properties are temperature-sensitive since the steep temperature gradient varies the properties significantly. Moreover, the energy needed for the solid-state phase transition is reflected by modifying the specific heat employing the latent heat of fusion. Furthermore, the multi-layer and multi-scan aspects of metal AM are considered by including the temperature history from previous layers and scans. Results from the analytical RS model presented excellent agreement with XRD measurements employed to determine the RS in the Ti-6Al-4V specimens.

The Eastern Kunlun Fault Zone (EKFZ) is located in a seismic blank area. This study investigates the hydrogeochemical characteristics of varied-temperature springs in the EKFZ to understand the relationship between fractures, fluids and earthquakes. It aids in establishing their induction mechanisms and assists in monitoring the earthquake precursors of the EKFZ. In this study, the main elements, trace elements, hydrogen and oxygen isotopes and strontium isotopes of 23 varied-temperature springs in the EKFZ were analyzed. The results reveal the source of groundwater recharge, hydrochemical types, mineral saturation, and for a select few springs indicative of geothermal activity, collected geothermal reservoir temperatures. The study also explores the relationship between earthquakes and springs, identifying sensitive chemical indicators. Based on continuous monitoring at Maqu Station, we found that before the occurrence of the Maerkang Ms 6.0 earthquake, the concentration of Cl− rose by 2.9 times, and 46 days before the Gande earthquake (Ms = 4.7), the concentrations of Na+ and SO42− significantly increased. Finally, a conceptual model of the hydrogeochemistry of springs is presented to describe the groundwater circulation in the study area. This research is of great significance for the analysis of fluid geochemistry in this area and for assessing the seismic hazards of the EKFZ.

This paper presents the results of investigations into the pyrolysis of waste polypropylene in a laboratory fixed-bed batch reactor. The experiments were designed and verified in such a way as to allow the application of the Response Surface Methodology (RSM) in the development of an empirical mathematical model that quantifies the impacts mentioned above. The influence of the mass of the raw material (50, 100 and 150 g), together with the reactor temperature (450, 475 and 500 °C) and the reaction time (45, 50 and 75 min) was examined. It has been shown that the mass of the raw material, i.e. the filling volume of the reactor, has a significant influence on the pyrolysis oil yield. This influence exceeds the influence of reactor temperature and reaction time. This was explained by observing the temperature change inside the reactor at three different spots at the bottom, middle and top of the reactor. Recorded temperature diagrams show that with greater masses of feedstock, local overheating occurs in the middle part of the reactor, which leads to overcracking of vapor products, and from there to an increased formation of non-condensable gases, i.e. reduced yield of pyrolytic oil.

As one of the typical deposits in Sichuan-Yunnan-Guizhou Pb-Zn metallogenic province, the Daliangzi Pb-Zn deposit has a close genetic relation with the structural system of “black/fracture zone” formed under the action of NWW-approx. EW strike-slip structures in the metallogenic province, but the mechanism of rock and ore-controlling action of the structural system remains unclear. Based on detailed analysis of tectonite-mineralized alteration lithofacies of R1 “black/fracture zone”, the tectonite-mineralized alteration lithofacies zones can be divided into 4 types in succession outward from the Pb-Zn mineralization center, i.e., ① brecciated and stockwork-like Pb-Zn mineralization-complex breccia facies zone, ② stockwork-like Pb-Zn mineralization-simple breccia and cataclasite facies zone, ③ veined pyrite-sulfide-dolomitic cataclasite facies zone, and ④ fine-veined calcite-black carbonized dolomite facies zone; Cl- and SO42--rich high-temperature oxidizing ore-bearing fluid mixes with reducing fluid in Zone ① while migration and precipitation occur in Zone ④. With the evolution of ore-forming fluid, the homogenization temperature decreases from Zone ① to Zone ④, the salinity increases from Zone ① to Zone ② and then decreases to Zones ③ and ④, and the fluid density has little change on the whole; the contents of Zn, Pb, Cu, Ga, Ge, Cd, Ag, and other metallogenic elements, the Zn/Pb ratio, and the CaO/MgO mole ratio decrease gradually from Zone ① to Zone ④; and REE fractionation, calcilization, silicification, and pyritization enhance gradually from Zone ① to Zone ④. This series of changes are the product of diapirism (cryptoexplosion) of strike-slip structures and “black/fracture zone”, among which the second-order structures (F5, F100, and other faults) derived from NWW-approx. EW striking dextral shear-tension faults F1 and F15 control the brecciated and stockwork-like Pb-Zn mineralized complex breccia facies zones and the stockwork-like Pb-Zn mineralized simple breccia and cataclasite facies zones. Therefore, this paper establishes the zoning mode of tectonite-mineralized alteration lithofacies of “black/fracture zone” and proposes that Zones ① and ② are important prospecting criteria. conclusions.

P-band radar remote sensing applied during the Airborne Microwave Observatory of Subcanopy and Subsurface (AirMOSS) mission has shown great potential for estimation of root zone soil moisture. When retrieving the soil moisture profile (SMP) from P-band radar, a mathematical function describing the vertical moisture distribution is required. Because only a limited number of observations are available, the number of free parameters of the mathematical model must not exceed the number of observed data. For example, a second order polynomial that contains 3 free parameters was presumed based on in-situ SMP data. The polynomial is currently parameterized based on 3 backscatter observations provided by AirMOSS (i.e. one frequency at three polarizations of HH, VV and HV). In this paper, a more realistic, physically-based SMP model containing 3 free parameters is derived based on a solution to Richards’ equation for unsaturated flow in soils. Evaluation of the new SMP model based on both numerical simulations and measured data revealed that it exhibits greater flexibility for fitting measured and simulated SMPs than the currently applied polynomial. It is also demonstrated that the new SMP model can be reduced to a second order polynomial at the expense of fitting accuracy.

Plastic contamination of small dimensions (

The human landscape transforming activity contributes to the global change of vegetation in different forms. Hunting is one of the most ancient human landscape-shaping activities. Feeders for hunting are particularly disruptive to vegetation. In the present study, we conducted a vegetation survey in these highly disturbed places. We are investigating the vegetation dynamics over several years in in the turkey oak–sessile oak zone, in two areas with different moisture and shade conditions (forest and clearing). One important background factor is changes in precipitation and temperature. The novelty of our present study lies in the fact that the observation takes place with continuous disturbance, where the human influence is very large. Our results confirm that the weed infestation be detectable at bait sites over a long period, and the interannual changes were typical in every year, according to the fact that in August, more weed species are usually present with a greater cover at the bait sites. The main meteorological factors played a role in the degree of weed infestation in each year. There was a higher proportion of vegetation regeneration in wetter years, while dry periods do not favor successional processes. With the drying of the climate, the disturbed areas are constantly losing their natural value, but wetter weather is not an automatic solution either. A more precise understanding of vulnerable systems and careful planning of treatment interventions is necessary.

It is widely accepted that plastic waste is one of our most urgent environmental concerns the world is currently facing. Plastic has contributed greatly to innovation in all fields, but the raw material for its production (fossil fuels), as well as the linear economy in which it is currently produced and used, makes the material problematic from a sustainability and human health perspectives. The emergence of bio-based plastics provides an opportunity to reduce dependency on fossil fuels and transition to a more circular plastics economy. For polyethylene terephthalate (PET), one of the most prevalent plastics in packaging and textiles, there exist two bio-based alternatives that are similar or superior in material property and recyclability. These are polyethylene furanoate (PEF) and polytrimethylene terephthalate (PTT). The overarching aim of this study was to examine the transition from fossil-based to renewable plastics, through the lens of PET upcycling into PEF and PTT. The process for the production of PEF and PTT from three feed streams (post-consumer PET waste, lignocellulosic biomass-derived cellulose and biodiesel-derived crude glycerol) was developed in the software SuperPro Designer and the economic viability assessed via a discounted cumulative cash flow (DCCF) analysis. This study represents a conceptual case study of the valorisation of existing plastic waste into new, recyclable bio-based plastics, for a more sustainable plastics production. A techno-economic analysis of the designed process revealed that the minimum selling price (MSP) of second generation-derived PEF and PTT is 3.13 USD/kg, and that utilities and the feedstock used for the production of 2,5-furandicarboxylic acid (FDCA) needed in PEF synthesis contributed the most to the process operating costs. The effect of recycling PEF and PTT through the process at three recycling rates (42%, 50% and 55%) was investigated and revealed that increased recycling could reduce the MSP of the 2G bio-plastics (by 48.5%) to 1.61 USD/kg. This demonstrates that increasing recycling rates would have a beneficial effect on the economic viability of the plastic biorefinery.

How hands-on gardening impacts behaviors including healthy eating and physical activity during early childhood can be of critical importance for preventing early onsets of obesity. This research investigates how participating in hands-on gardening impacts preschoolers’ (3-5 years old) physical activity (measured by accelerometers) in childcare centers in the Semi-Arid Climate Zone. The research was conducted in eight licensed childcare centers located in West Texas with 149 children (n=149). Four childcare centers in the experimental group received hands-on garden interventions; the other four in the control group did not. In both experimental (intervention) and control (non-intervention) centers, children wore Actigraph GT3X+ accelerometers continuously for 5 days before and for 5 days after intervention (a total of 10 days). Results show that the duration of sedentary behavior of children in the experimental (intervention) group significantly decreased compared to children in the control (non-intervention) group. The finding suggests that the positive effects of childcare hands-on gardening on physical activity extend to semi-arid climate zones where gardening is challenging due to high temperatures and lack of annual rainfall. The research emphasizes the critical need to incorporate hands-on gardening in childcare centers as an obesity prevention strategy nationally in the U.S. and beyond.

As the additive manufacturing industry grows, it is compounding the global plastic waste problem. Distributed recycling and additive manufacturing (DRAM) offers an economic solution to this challenge, but it has been relegated to either small-volume 3D printers (limiting waste recycling throughput) or expensive industrial machines (limiting accessibility and lateral scaling). To overcome these challenges, this paper provides proof-of-concept for a novel open-source hybrid 3D printer that combines a low-cost hanging printer design with a compression screw-based end-effector that allows direct extrusion of recycled plastic waste in large expandable printing volumes. Mechanical testing of the resultant prints from 100% waste plastic, however, showed that combining challenges of non-uniform feedstocks and a heavy printhead for a hangprinter reduced the strength of the parts compared to fused filament fabrication. The preliminary results are technologically promising, however, and provide opportunities to improve on the open source design to help process the volumes of waste plastic needed for DRAM to address the negative environmental impacts of global plastic use.

Abstract: In order to accelerate deployment of distributed recycling by providing low-cost feed stocks of granulated post-consumer waste plastic, this study analyzes an open source waste plastic granulator system. It is designed, built and tested for its ability to convert post-consumer waste, 3-D printed products and waste into polymer feedstock for recyclebots of fused particle/granule printers. The technical specifications of the device are quantified in terms of power consumption (380 to 404W for PET and PLA, respectively) and particle size distribution. The open source device can be fabricated for less than USD$2000 in materials. The experimentally-measured power use is only a minor contribution to the overall embodied energy of distributed recycling of waste plastic. The resultant plastic particle size distributions were found to be appropriate for use in both recyclebots and direct material extrusion 3-D printers. Simple retrofits are shown to reduce sound levels during operation by 4dB-5dB for the vacuum. These results indicate that the open source waste plastic granulator is an appropriate technology for community, library, makespace, fab lab or small business-based distributed recycling.

This letter attempts to clarify an issue regarding the proper definition of plastic dislocation density tensor. This study shows that the Ortiz’s and Berdichevsky’s plastic dislocation density tensor are equivalent with each other, but not with Kondo’s one. To fix the problem, we propose a modified version of Kondo’s plastic dislocation density tensor.

In former times, the spinal cord was considered a hard-wired network for spinal reflexes and a conduit for long-range connections. This view has changed dramatically over the past few decades. It is now recognized as a plastic device whose structures and functions adapt to changing circumstances. While such changes also occur under physiological conditions, the most dramatic alterations take place during or after various pathological events. It is astonishing what mechanisms the musculo-skeletal system has evolved to come to grips with the damages. Many of these changes are maladaptive, but some appear to help adapt to the new conditions. Although myriads of studies, using manifold methods, have been devoted to elucidating the underlying mechanisms, in humans and animal models, the etiology and pathophysiology of various diseases are still little understood, due to a number of reasons. We will here try to summarize some results and remaining problems in a selection of diseases, in particular spinal muscular atrophy (SMA), amyotrophic laterals sclerosis (ALS), and predominantly spinal cord injury (SCI) with occasional relations to stroke. Especially the changes in SCI (and stroke) depend on the cause, site and extent of the afflicted damage and are therefore multifarious. At the end, we will briefly summarize results indicating that operant, classical and instrumental conditioning can be used to produce plastic changes in healthy people, with potentials for applications to patients with spinal cord injury. In order not to overload the article, we will not delve deeply into sub-cellular processes.

In this review, severe plastic deformation (SPD) is considered as a materials processing technology. The deformation mode is the principal characteristic differentiating SPD from common forming operations. For large plastic strains, deformation mode depends on the distribution of strain rates between continuum slip lines and can be varied from pure shear to simple shear. A scalar, invariant and dimensionless coefficient of deformation mode is introduced as a normalized speed of rigid rotation. On this basis, simple shear provides the optimum mode for structure modification and grain refinement whereas pure shear is "ideal" for forming operations. Special experiments and SPD practice confirm this conclusion. Various techniques of SPD are classified and described in accordance with simple shear realization or approximation. It is shown that correct analyses of the processing mechanics and technological parameters are essential for comparison of SPD techniques and the development of effective industrial technologies.

Diabetes mellitus is one of the most common endocrinopathies, estimated to affect about 5.4% of the world's population around 2025. It is thought that nearly a third of diabetic patients have some type of skin condition. Frequently, the cutaneous effects of this heterogeneous syndrome are ac-curately detected late in the progressive form of the disease. The main objective of the present study was to identify the main cellular characteristics of the cutaneous microenvironment in exper- imentally induced diabetes mellitus. Skin fragments were harvested from adult white Wistar rats of both sexes, with the weight of 200 g, 12 weeks after streptozotocin diabetes was induced. In parallel with histopathological diagnosis by using hematoxylin and eosine staining, samples were processed by transmission electron microscopy technique and examined with a Philips CM100 microscope. In the apparently macroscopically unchanged tegument, photon microscopy revealed both progres ive thinning of the epidermis in the early stages of diabetes and a significant process of fibrosis and collagen hyalinization in the dermis. In addition, in the early stages, the electron microscopic study provided ultrastructural details characteristic of a senescent phenotype with reduced cell proliferation. The morphological changes in the skin may be the first signs of disruption of carbohydrate metabolism and in the case of established diabetes may reflect its progression and the efficacy of therapy.

Excessive production, consumption and indiscriminate disposal of plastic waste cause an increasing plastic pollution with detrimental impacts on environment and human health. This study aimed to assess the level of knowledge, attitude, and practices (KAP) towards plastic pollution among Malaysians and evaluate the variation of plastic pollution related KAP among various socio-demographics. An online survey was conducted, and 294 valid responses was obtained. Descriptive statistics, KAP scoring and cross tabulation of responses were estimated. One-way analysis of variance, paired t-test and binary logistic regressions were carried out. Results showed that respondents had poor knowledge (mean 7.41 ± 1.80) and practice score (3.81 ± 1.39) across all socio-demographics. Compared to younger (18-30 years) respondents, older ones (>46 years) had higher knowledge (odds ratio, OR 4.304; p<0.01). However, middle aged (31-45 years) respondents reported significantly (p<0.01) higher attitude (OR 4.019) and practice (OR 4.056; p <0.05). Respondents with environmental related university education had showed higher odds about plastic pollution related knowledge (OR 10.343; p<0.01). Suggestions are made to undertake interventions such as environmental awareness creation, incorporating plastic pollution topics in formal and informal education, and providing recycling facilities nearby the localities for encouraging good practices towards minimizing plastic uses and pollution.

Global use of single-use non-biodegradable plastics, like bottles made of polyethylene tereph-thalate (PET), have contributed to catastrophic levels of plastic pollution. Fortunately, microbi-al communities are adapting to assimilate plastic waste. Previously, our work showed a full consortium of five bacteria capable of synergistically degrading PET. Using omics approaches we identified key genes implicated in PET degradation within the consortium’s pangenome and transcriptome. This analysis led to the discovery of a novel PETase, EstB, discovered to hydrolyze oligomer BHET, and polymer PET. Besides genes implicated in PET degradation, many other biodegradation genes were discovered. Over 200 plastic and plasticizer degrada-tion related genes were discovered through the Plastic Microbial Biodegradation Database (PMBD). Diverse carbon source utilization was observed by a microbial community-based as-say, which paired with an abundant number of plastic and plasticizer degrading enzymes in-dicates a promising possibility for mixed plastic degradation. Using RNAseq differential analysis, several genes were predicted to be involved in PET degradation including aldehyde dehydrogenases and several classes of hydrolases. Active transcription of PET monomer me-tabolism was also observed, including the generation of polyhydroxyalkanoate (PHA) bi-opolymers. These results present an exciting opportunity for the bio-recycling of mixed plastic waste with upcycling potential.

Background Nigeria is among the top 5 countries that have the highest gap between people reported as diagnosed and estimated to have developed Tuberculosis (TB). To bridge this gap, there is a need for innovative approaches to identify geographical areas at high risk of TB transmission and targeted Active Case Finding (ACF) interventions. Leveraging community level data together with granular sociodemographic contextual information can unmask local hotspots which could be otherwise missed. This work evaluated if this approach helps to reach communities with higher numbers of undiagnosed TB. Methodology A retrospective analysis of the data generated from an ACF intervention program in 4 south-western states in Nigeria was conducted. Wards (the smallest administrative level in Nigeria) were subdivided into further smaller population clusters. ACF sites and their respective TB screening outputs were mapped to these population clusters. This data was then combined with open-source high resolution contextual data to train a Bayesian inference model. The model predicted TB positivity rates on the community level (population cluster level), and these were visualised on a customised geoportal for use by the local teams to identify communities at high risk of TB transmission and plan ACF interventions. The TB positivity yield (proportion) observed at model-predicted hotspots was compared with the yield obtained at other sites identified based on aggregated notification data. Results The yield in population clusters that were predicted to have high TB positivity rates by the model was at least 1.75 times higher (p-value <0.001) than the yield in other locations in all four states. Conclusion The community level Bayesian predictive model has the potential to guide ACF implementers to high TB positivity areas for finding undiagnosed TB in the communities, thus improving efficiency of interventions.

This research delves into a detailed exploration of the thermal decomposition behavior of bio-based polymers, specifically Thermoplastic Starch (TPS) and Poly(lactic acid) (PLA). The study focuses on the impact of three different heating rates under a nitrogen atmosphere, providing comprehensive insights into the thermal stability of these eco-friendly polymers. In particular, the TPS kinetic model is examined, encompassing the decomposition of three distinct fractions. In contrast, PLA exhibits a simplified kinetic behavior requiring only a fraction described by a zero-order model. The kinetic study involves a systematic investigation into the individual contributions of key components within TPS, including starch, glycerin, and polyvinyl alcohol (PVA). This nuanced analysis contributes to a comprehensive understanding of the thermal degradation process of TPS and PLA, enabling the optimization of processing conditions and the prediction of material behavior across varying thermal environments. Furthermore, the incorporation of different starch sources and calcium carbonate additives in TPS enhances our understanding of the polymer's thermal stability, offering insights into potential applications in diverse industries.

This preprint is focused in the presence of plastics and microplastics in food. We will discuss how many we eat, and how they arrive to the food, and why. We will treat many other things, such as the waste treatment in Europe and in Spain, with updated data; how much plastic waste is generated; what are microplastics and how they are analyzed, I will tell about the experience we have at the University of Alicante (UA); how they can be removed and we will estimate how many we eat over the course of a year.

In this study, the physical properties of briquettes produced from two different biomass feedstocks (sawdust and date palm trunk) and different plastic wastes were investigated, without using any external binding agent. The biomass feedstocks were blended with different ratios of two WEEE plastics (halogen-free wire and print circuit boards (PCB)) and automotive shredder residues (ASR). The briquettes production is studied at different waste proportions (10-30%), pressures (22-67 MPa) and temperatures (room-130 ˚C). Physical properties as density and durability rating were measured, usually increasing with temperature. Palm trunk gave better results than sawdust in most cases, due to its moisture content and the extremely fine particles that are easily obtained.

Parts of shotgun cartridges are a significant source of plastic litter in the marine environment. Empty cartridge shells may not be picked up by the hunter who fired them, and plastic wads that serve to separate the propellant from the shot load, are lost down-range when a shot is fired. Such litter items constitute a cosmetic and aesthetic problem on coastlines and may cause harm to marine animals and in the later stages of decomposition break down into harmful micro plastic particles. There exists no reliable estimate of the global exposure of marine ecosystems to this plastic source. However, in some countries it has been subject to closer examination, including for example, Denmark where the annual contribution of plastic wads into marine systems was estimated to 600,000 pieces (c2 tonnes), and the accumulated density of washed-up items (both wads and shells) was 3.7 items per 100 m coastline. Increasing awareness of this problem has caused scientists, hunters’ communities and governments to suggest altered practice including transition to the use of biodegradable cartridge components, first and foremost wads as this item is invariable lost during hunting. Several manufacturers provide shotgun cartridges containing biodegradable wads based on different types of materials, including fibers and various types of plastics, for example PVAL (poly(vinyl alcohol)) and PHA (polyhydroxyalkanoate). In this paper, we review the most recent literature on the amounts and related environmental hazards of plastic dispersed from hunting ammunition into marine ecosystems. We summarize the market availability of shotgun cartridges with biodegradable wads and discuss chemical, technical, economical and legal aspects of a transition to the use of such products.

Demolished concrete and plastic waste are two increasingly aggravating problems. In this study, a novel method was proposed to simultaneously recycle concrete and plastic wastes by compacting concrete and plastic powders together under pressure and temperature. The influence of compression pressure and temperature as well as the mixture proportion on the bending strength of specimens was investigated. The results showed that pressure and temperature had a positive effect on the specimen strength; however, the molding temperature should not exceed the melting temperature of plastic. The proportion of plastic had a minimal effect on the bending strength of the specimen when plastic accounted for 25%–75% of the overall mass of the test piece.

Thermal and catalytic pyrolysis of virgin low-density polyethylene (LDPE), high-density polyethylene (HDPE), polypropylene (PP) and mixtures of LDPE/PP were carried out in a 200 ml laboratory scale batch reactor at 460 °C in a nitrogen atmosphere. Thermogravimetric analysis (TGA) was carried out to study the thermal and catalytic degradation of the polymers at a heating rate of 10 °C/min. The amount of PP was varied in the LDPE/PP mixture to explore its effect on the reaction. In thermal degradation (TGA) of LDPE/PP blends, a lower decomposition temperature was observed for LDPE/PP mixtures compared to pure LDPE, indicating interaction between the two polymer types. In the presence of a catalyst (CAT-2), the degradation temperatures for the pure polymers were reduced. The TGA results were validated in a batch reactor using PP and LDPE respectively. Thermal cracking results showed that the oil product contains a significant amount of gasoline (C7 − C12) and diesel (C13 − C20) hydrocarbon fractions. The catalyst enhanced cracking at lower temperatures and narrowed the hydrocarbon distribution in the oil towards the gasoline range fraction (C7 – C12). The result suggests that the oil produced from catalytic pyrolysis of waste plastics has a potential as an alternative fuel.

Polystyrene (PS) is an extremely stable polymer with relatively high molecular weight and a strong hydrophobic character that makes it highly resistant to biodegradation. In this study, PS was subjected to biodegradation tests by Tenebrio Molitor (T. Molitor) and Zophobas Morio (Z. Morio) larvae. Specifically, six different experimental diets were compared: (i) T. Molitor fed with bran; (ii) T. Molitor fed only PS; (iii) T. Molitor fed only PS treated with H2O2; (iv) Z. Morio fed with bran; (v) Z. Morio fed only PS and (vi) Z. Morio fed only PS treated with H2O2. Therefore, the mass change of the larvae and the survival rate were measured periodically, while the frass collected after 15 and 30 days were analyzed by different analyses, such as spectroscopy (FTIR), spectrometry (molecular weight and polydispersity), and microscopy (scanning electron microscopy observations). The obtained results suggest that in the case of T. Molitor larvae, larvae feeding on bran showed the highest survival rate of ~94 % at 30 days, while in the case of the Z. Morio larvae, the highest survival rate was exhibited by larvae eating PS-H2O2. Although not strongly pronounced, the Mw and Mn of PS frass of both T. Molitor and Z. Morio larvae decreased over 30 days, suggesting the Ps biodegradation. Finally, the morphological analysis shows that PS samples isolated from the frass of T. Molitor and Z. Morio larvae showed completely different, rough and irregularly carved surface structures, in comparison to PS before biodegradation.

The Doig Phosphate Zone (DPZ) is a phosphate-bearing marine unit located at the base of the Doig Formation, in the Triassic section of the Western Canada Sedimentary Basin. The DPZ has a maximum thickness of 90 m and extends across northeastern British Columbia and western central Alberta. In this study we characterize the significance and interpret the origin of apatite in the DPZ, through mineralogical and geochemical analyses, thin section study and field emission-scanning electron microscopy. The occurrence of apatite in the DPZ is not evenly distributed, but restricted to discrete 10 to 20 cm thick beds, located near the base of the DPZ. Phosphorites are of two types: grainstones composed primarily of unconformity-bounded coated grains, and intraclastic phosphorites composed of detrital silt-sized grains and apatite coated grains in a cryptocrystalline phosphatic matrix. The phosphorite beds are records of stratigraphic condensation due to low detrital input during transgression. The erosionally-truncated phosphatic coated grains and intraclasts are interpreted to be a result of various phases of phosphatization, exhumation, erosion reworking, winnowing and redeposition in alternating quiescence and storms or bottom currents. The abundance of pyrite and chalcophile trace elements, as well as the low concentration of proxy elements for organic matter productivity and preservation, are further evidences of stratigraphic condensation, with sulfidic pore water development and extensive organic recycling promoted by biological activity during the long exposure times. The phosphorites were formed under oxygenated water conditions, as suggested by the depletion in Ce and presence of a diverse benthic fauna.

The concept of gray-zone lymphoma (GZL) has been progressively refined since its in-troduction in the literature in 1998. For several years, it was applied to a rather broad spectrum of conditions, posing the problem of the differential diagnosis between any type of Hodgkin lymphoma (HL) and diffuse large B-cell lymphoma, with special reference to primary mediasti-nal forms (PMBL). Officially recognized as a provisional entity in the 4th and revised 4th editions of the WHO Classification of Tumour of Haematopoietic and Lymphoid Tissues with the term “B-cell lymphoma unclassifiable with features intermediate between diffuse large B-cell lym-phoma and classical Hodgkin lymphoma”, it was limited to tumours, which showed either morphologic features reminiscent of classical HL (CHL) but carrying a complete B-cell pheno-type or conversely provided with a PMBL morphology but revealing CHL phenotypic charac-teristics. The definition of GZL has been further revised in the recently published International Lymphoma Classification and 5th Edition of the WHO Classification of Haemato-lymphoid Tu-mours, which have limited it to mediastinal neoplasms based on emerging molecular evidences. The aim of this review is to critically discuss the issue of GZL, also in the light of the suboptimal response to current therapies.

This paper combines a literature survey and data analysis. The literature on the Subtropical Front (STF) in the Southern Ocean is reviewed with a two-pronged emphasis on the double-front structure of the STF, hence the existence of a subtropical frontal zone (STFZ), and the circumpolar continuity of the STFZ. The data analysis is based on the World Ocean Circulation Experiment (WOCE) sections. The STFZ is detected along each section independently from other sections, while moving circum-polarly downstream (eastward). The literature survey and data analysis confirm the circumpolar continuity of the STFZ extending from the Brazil Current across the South Atlantic, South Indian, and South Pacific up to Chile, being bound by the North and South STF. The circumpolar continuity of the STFZ is partly interrupted by South Africa and Tasmania, where the North STF ceases, while the South STF continues eastward. The South Atlantic STFZ is the southern boundary of the well-defined Subtropical Mode Water (STMW) thermostad, which cools eastward from 15°C to 11°C between the Brazil Current and Greenwich Meridian. In the southeast Pacific, the STFZ is the southern boundary of the 17-to-19°C thermostad (South Pacific Eastern STMW). The STFZ’s vertical extent is at maximum in the South Atlantic (>1000 m), decreasing eastward to 300 m in the southeast Pacific off Chile. A special attention is given to the South Pacific and the STFZ’s role in the ecology of Chilean jack mackerel Trachurus murphyi that spawn at the STFZ and migrate along the STFZ from Chile up to New Zealand.

The use of plastic in agriculture has become so omnipresent within the industry that it has acquired it own lexicon to become known as ‘plasticulture’. However, since, compared to other industries the quantities consumed are low, little attention is granted to this waste stream. This is the case both with local and international policies even though it bears a close connection to soil health and therefore is a prerequisite to improve the sustainability of food production processes including food security. Using Malta as a case study, the research utilises quantitative and qualitative tools to identify and quantify the most common types of agricultural plastic waste generated and determines the attitudes of farmers towards a collection and recycling scheme. While it identifies that incineration and ploughing of plastic waste as regular practices, it also ascertains the willingness of farmers to acquire more knowledge about more appropriate methods to dispose of this waste stream thus guiding policy makers towards the need to initiate educational measures for farmers to prevent these harmful practices. Through stakeholder interviews the research highlights that the present lack of data is a major hindrance for policy to take account of this waste stream.

Online artificial intelligence (AI) tools have recently gained in popularity. So-called “generative AI” chatbots unlock new opportunities to access vast realms of knowledge when being prompted by users. Here, we test the capabilities of two such AIs in order to determine the benefits for plastic surgery while also assessing potential risks. Future developments are outlined. We used the online portals of OpenAI’s ChatGPT(version 3.5) and Google’s Bard to ask a set of questions and give specific commands. Results provided by the two tools were compared and analyzed by a committee. For professional plastic surgeons, we found that ChatGPT and Bard can be of help when it comes to conducting scientific reviews and helping with scientific writing but are of limited use due to the superficiality of their answers in specific domains. For medical students, in addition to the above, they provide useful educational material with respect to surgical methods and exam preparation. For patients, they can help when it comes to preparing for an intervention, weighing in risks and benefits, while providing guidance on optimal post-operative care. ChatGPT and Bard open widely accessible data to every internet user. While they might create a sense of “magic” due to their chatbot interfaces, they nonetheless can help to increase productivity. For professional surgeons, they produce superficial answers - for now - albeit providing help with scientific writing and literature reviews. For medical students, they are great tools to deepen their knowledge about specific topics such as surgical methods and exam preparation. For patients, they can help in translating complicated medical jargon into understandable lingo and provide support for pre-operative as well as post-operative care. Such AI tools should be used cautiously as answers are not always precise nor accurate and should always be used in combination with expert medical guidance.

Abandoned, lost, or otherwise discarded fishing gear (ALDFG) is a primary contributor to the entanglement of numerous marine species. Utilizing digital media platforms like Google, Facebook, and Instagram we conducted an assessment of the detrimental effects of ALDFG and plastic litter, on the biodiversity of Italy's marine ecosystem. Our investigation revealed that plastic litter has adverse consequences on various forms of marine life, including reptiles, mammals, birds, fish, crustaceans, and mollusks, along different Italian geographical sub-areas. Several records of interaction between plastic and endangered and vulnerable marine species have been described. Our reports even highlight the impact on marine turtles, mainly on Caretta caretta. This is the first report of entangled with fishing nets in Cetorhinus maximus, Oblada melanura, Serranus scriba, Homarus gammarus, Octopus vulgaris, and Phoenicopterus roseus. Furthermore, we identified that ghost nets have repercussions for endangered and vulnerable marine species. This update sheds light on the ongoing adverse effects of ghost nets on the Italian marine ecosystem, yet it is crucial to acknowledge that the true extent of the problem remains underestimated.

HDPE (high-density polyethene) plastic waste is stronger, harder, and more resistant to high temperatures than other plastics. Using it as an additive in a concrete mixture is one solution to reduce this type of waste. We examined how HDPE-type plastics can be used as an additive material in the manufacture of concrete to improve its hardness, tensile strength and compressive strength. Using 156 samples, we aimed to identify the effect of HDPE plastic fibres on concrete of three qualities; B0, f'c10 MPa (low quality), and f'c25 MPa (medium and high quality). We added four compositions (2.5%, 5%, 10% and 20% by weight of cement) of HDPE plastic fibre to each quality of cement, with HDPE plastic fibre sizes of 1 x 1 cm, 0.5 x 2 cm or 0.25 x 4 cm. We found that the addition of 5% HDPE plastic fibre with a 0.5 x 2 cm cross-sectional shape to the f'c10 MPa concrete gives the best result, with increased tensile and compressive strength of the concrete.

The research is devoted to the study of geotectonic and geodynamics of the Shu-Ile belt and petrographic composition and intrusive complexes geochemical features analysis. The Shu-Ile suture is an important geological structure of Kazakhstan. It is characterized by the presence of various intrusive formations and deep faults. The material composition of these intrusions is of interest for understanding the geological and metallogenic processes in this region. The research used modern scientific methods, including petrographic and geochemical studies of various compositions intrusion samples. Based on the results of material composition studies of intrusive complexes, their possible connections with other geological structures of Kazakhstan and the metallogeny of the region have been established. Based on the data obtained, a conclusion was made about the intrusive complexes origin and evolution of the Shu-Ile belt, which may be important for further geological research and forecasting of mineral resources in the region.

The purpose was to reflect on the sustainability of artisanal and informal mining in the Peruvian Andean zone by 2022. The type of research was basic, non-experimental design, ex post facto scope. The sample consisted of: statistics on crime prevention due to socio-environmental conflicts from the National Prosecutor's Office and the Ombudsman's Office, reports of interventions targeted at artisanal and informal miners. The procedure focused on gathering secondary information for a documentary review analysis that is based on proven and disseminated past facts. Artisanal and informal mining is strengthened in the Peruvian Andean zone by incidence and force: 1) the social license and agreements by community assembly, 2) the flexibility in compliance with the formalization, preventive and environmental protection laws, 3) the 50% increase in socio-environmental conflict due to mining activity, 4) a 25% progressive increase in the production costs of agricultural and livestock activities. The direct consequences on environmental sustainability are: 1) the delimited reconversion of the change in agricultural land use in a third of the communal territories in basin headwaters; 2) displacement of environmentally friendly economic activity by 20% in basin headwaters; 3) the impossibility of modification or intervention in water surfaces, bofedales by communal agreements.

The Krudum granite body comprises highly fractionated granitic rocks ranging from medium-F biotite granites to high-F, high-P₂O₅ Li-mica granites. This unique assemblage is an ideal site to continue recent efforts in petrology to characterize the role of zircon, monazite and xenotime as hosts to REEs. The granitic rocks of the Krudum body analysed in this study were found to contain variable concentrations of monazite and zircon, while xenotime was only found in the high-F, high-P₂O₅ Li-mica granites and in the alkali-feldspar syenites of the Vysoký Kámen stock. For analysed monazites of all magmatic suites cheralite substitution was significant. The highest concentration of cheralite was found in monazites from the high-F, Li-mica granites and from the alkali-feldspar syenites. The proportion of YPO₄ in all analysed xenotimes ranges from 71 to 84 mol. %. Some xenotimes were found to be hydrated and the observed water content estimated from analytical data ranged from 5 to 11 wt. % H₂O. Analysed xenotimes were commonly enriched in HREEs (9.3– 19.5 wt. % HREE₂O₃) and thorite-coffinite and cheralite exchange was observed. Analysed zircons from granite suites of the Krudum granite body contained moderate Hf concentrations (1.0–4.7 wt. % HfO₂; 0.010–0.047 apfu Hf). The highest concentrations of HfO₂ were found in zircons from the high-F, high P₂O₅ Li-mica granites (1.2–4.7 wt. % HfO₂) and from the alkali-feldspar syenites (1.3–4.1 wt. % HfO₂). Zircons from the high-F, high-P₂O₅ Li-mica granites were often hydrated and fluorised. The concentrations of F in zircon from partly greisenised high-F, high-P₂O₅ Li-mica granites reached up to 1.2 wt. % (0.26 apfu F). In zircons from the alkali-feldspar syenites enrichment in P, which is not associated with a simultaneous enrichment in Y + REE, was also observed. Analysed zircons from the high-F, high P₂O₅ Li-mica granites were enriched in Y (up to 5.5 wt. % Y₂O₃; 0.10 apfu Y) and Sc (up to 1.17 wt. % Sc₂O₃; 0.03 apfu Sc).

Despite the increase in popularity of Zero Waste (ZW) concept, the successful implementation of this concept in waste management is still facing many challenges. The plastic recycling rate in Australia is currently only about 9.4%, which could leave up to 90.6% of plastic consumption being sent to landfills. The state of Victoria (in Australia) has proposed an ambitious plan to upgrade its waste and recycling system and to divert about 80% of waste from landfills by 2030. The aim of this research is to study Victoria’s current waste management plan and to develop a simulation model to assess the feasibility of it achieving zero plastic waste by 2035. In this direction, a fundamental knowledge of global ZW implementation needs to be acquired in order to understand the challenges, obstacles, and uncertainties in achieving ZW target. A simulation model is established using a method called double baselines. This method was developed as an improvisation to address the limitation of data availability for the model development. The model will run on 4 scenarios including one from Victoria’s current plan. Outcomes from the model are produced in comparative charts covering 6 key considerations including the rates of plastic consumption, waste to landfill, diversion, recycling, relative accumulative cost and effort. The findings of this study pointed out that Victoria’s current plan are feasible for its goal and presented with opportunities for improvement especially towards zero plastic waste. Besides, study results also reveal that the Victoria’s current plan to achieve 80% diversion rate by 2030 is possible but the zero plastic waste target by 2035 is less likely to happen.

Plastics have become an indispensable part of modern life today. The global production of plastics has gone up to 299million tones in 2013, which is believed to be increasing in the near future. The utilization of plastics and its final disposal pose a tremendous negative significance impacts on the environment. The aim of this study was to investigate the thermal and catalytic pyrolysis for production of fuel oil from the polyethene plastic wastes. Catalysts used in the experiment were acid activated clay mineral and aluminum chlorides on activated carbon. The clay mineral was activated by refluxing it with 6M Sulphuric acid for 3hours. The experiment was conducted in three different phases: the first phase of the experiment was done without a catalyst where 88mL oil was obtained at a maximum temperature of 39 and heating rates of 12.5, reaction time of 4hours. The second phase involves the use of acid activated clay mineral where 100mL of oil was obtained and heating rates of 12.5 and reaction time of 3hours 30minutes. The third phase was done using aluminium chlorides on activated carbon and 105ml oil was obtained at a maximum temperature of 400 and heating rates of 15.5 reaction time of 3hours 10minutes. From the results, catalytic pyrolysis is more efficient than purely thermal pyrolysis and homogenous catalysis (aluminum chlorides) shows a better result than solid acid catalyst (activated clay minerals) hence saving the energy needed for pyrolysis and making the process more economically feasible.

We propose a spectral filter based on Plastic Optical Fiber with micro-holes as a low-cost, robust, and highly reproducible spectral filter. The spectral filter is explored for two configurations: fiber extended in a straight line, and a fiber optic loop mirror scheme configuration. The transmission traces indicate a spectral blue shift of peak transmission, at 587 nm, 567 nm, 556 nm, and 536 nm for 0, 1, 2, and 3 holes in the fiber, respectively. The filter exhibits a bandpass period of approximately 120 nm. Additionally, we conducted a comparison of the transmission with holes separated by distances of 1 cm and 500 μm. The results demonstrate that the distance between holes does not alter the spectral transmission of the filter. In the case of the fiber loop mirror configuration, we observed that the bandpass can be adjusted, suggesting the presence of multimode interference. Exploring variations in the refractive index within the holes by filling them with glucose solutions at various concentrations, we determined that the filtering band and spectral shape remains unaltered, ensuring a stable and robust operation of our spectral filter.

This study evaluates for the first time the plastic litter occurrence in Posidonia spheroids of four Mediterranean sandy beaches at different anthropogenic impact. A total of 80 spheroids was analyzed and 202 plastic items were found. Spheroids entangled a high number of plastic litter (132 plastic items/kg) with significant differences between beaches. Our results highlight the importance to implement the beach cleaning plan for the removal of all spheroids in order to prevent them from flaking and releasing the marine litter trapped inside them again in the environment. Spheroids should be manually removed in order to protect the banquettes. The removal should be involved all spheroids, independently from their size. This study adds data for the implementation of the monitoring program of marine litter and contributes to the development of specific management measures as well as implement Mediterranean action plans.

The microbial colonisers of plastics – the ‘plastisphere’ – can affect all interactions that plastics have with their surrounding environments. While only specifically characterised within the last 10 years, at the beginning of 2021 there were 140 primary research and 65 review articles that investigate at least one aspect of the plastisphere. We gathered information on the locations and methodologies used by each of the primary research articles, highlighting several aspects of plastisphere research that remain understudied: (i) the non-bacterial plastisphere constituents; (ii) the mechanisms used to degrade plastics by marine isolates or communities; (iii) the capacity for plastisphere members to be pathogenic or carry antimicrobial resistance genes; and (iv) meta-OMIC characterisations of the plastisphere. We have also summarised the topics covered by the existing plastisphere review articles, identifying areas that have received less attention to date – most of which are in line with the areas that have fewer primary research articles. Therefore, in addition to providing an overview of some fundamental topics such as biodegradation and community assembly, we discuss the importance of eukaryotes in shaping the plastisphere, potential pathogens carried by plastics and the impact of the plastisphere on plastic transport and biogeochemical cycling. Finally, we summarise the future directions suggested by the reviews that we have evaluated and suggest other key research questions.

Plastics are extensively used due to their versatility, durability, and low cost. PET stands for Polyethylene terephthalate. PET plastic is widely used all over the world and has many applications ranging from water bottles to fabrics like polyester and many things in between. But its unrestrained use in every field is resulting in heaps and piles of non-biodegradable materials causing damage to the environment and causing pollution. The idea being proposed is to degrade the PET plastic biologically using different bacteria. The bacteria used in this process are Ideonella sakaiensis, Acetobacterium woodii, Pelotomaculum and Methanospirillum hungatei. PET plastic is degraded, yielding Terephthalic Acid (TPA) and Ethylene Glycol (EG) by the action of the bacterium I. sakaiensis. Degradation of EG by A. woodii results in the formation of acetate and ethanol. TPA is degraded by the action of the coculture of Pelotomaculum and M. hungatei thereby yielding methane and acetate. All these products formed have significant commercial uses in various industries. The complete process that is to be carried out can help in achieving sustainability by fulfilling various Sustainable Development Goals set by the United Nations.

Despite good intentions, the increasing number of plastic bag bans aimed at alleviating marine plastic pollution saw a correlated increase in the number of unintended consequences that emerged alongside the bans, suggesting that human behavior towards plastic bag consumption have not changed, but merely shifted, and are feeding into other major international environmental catastrophes. Nudge theory, which helps people make better choices for themselves without inhibiting their free will, is a potential solution that has been shown to play a subtle but important role in providing options under circumstances where complex information needs to be streamlined for the wider community, avoiding any unintended consequences and behavioural shifts that might arise from instruments that diminishes autonomy. It is therefore timely to look into the insights of nudge theory to encourage a positive behavioural change to reduce plastic bag consumption. Here we apply a systematic literature review to show how successful applications of nudges in supermarkets can be leveraged to reduce plastic bag consumption. We find that the current applications of nudges in various industries worldwide, including supermarkets have produced positive and encouraging results, as well as producing lasting behavioural change among the wider community. Supermarkets are identified as a powerful deployment site of these nudges due to their positioning as a dominant provider of plastic bags to the wider community, as well as being the largest and leading provider of daily food needs. Finally, we synthesise our findings to produce a coherent and testable framework of actionable interventions that supermarkets can employ to nudge customers towards reduced plastic bag reliance, accompanied with a visual timeline of a customer shopping in a supermarket experiencing these nudges.

Disinfection byproducts (DBPs) are formed whenever disinfectant ingredients are in contact with organic matter. Due to widespread increase in production and use of disinfectants and antiseptics, the presence of their components in coastal environments is increasing. However, very limited scientific literature is available in regard to the occurrence of DBPs and related compounds in the coastal zone and particularly in seawater. In this context, the aim of this preliminary compilation is to outline the main up-to-date findings and raise awareness on their increasing occurrence in coastal environments. Sampling and analysis of marine samples in the USA, Spain, China, Taiwan, Malaysia, Korea, Kuwait and Hong-Kong revealed the presence of several categories of DBPs and related compounds in coastal environments, with the highest levels being detected in urban areas, probably related to the nearby wastewater treatment plants. The investigations considered in this preliminary compilation, report the detection of DBPs and related compounds as well as the formation of toxic brominated and iodinated DBPs in high levels due to chlorination of wastewater, especially after use of seawater for flushing in toilets. New DBP groups have also been detected, namely halogenated phenolic DBPs and halopyrroles.

Mediterranean Ridge accretionary complex (MAC) is one of the most critical subduction zones in the world. It is known that the region exhibits a continuous mass change (horizontal/vertical movements). This process is associated with the devastating and tragic earthquakes shaking the MAC for centuries. Here, we investigate the ocean bottom pressure (OBP) anomalies in the MAC derived from the Gravity Recovery and Climate Experiment (GRACE) and GRACE Follow On (GRACE-FO) satellite missions. The OBP time series for the MAC comprises a decreasing trend in addition to 1-, 1.53-, 2.36-, 3.67-, and 9.17-year periodic components partially explained by the atmosphere, oceans, and hydrosphere (AOH) processes, and Earth's pole movement. We noticed that the OBP anomalies appear to link to a rising trend and periods in earthquakes' power time series. This finding sheds new light on the mechanisms controlling the most destructive natural hazard.

The existence of the exclusion zone (EZ), a layer of water in which plastic microspheres are repelled from hydrophilic surfaces, has now been independently demonstrated by several groups. A better understanding of the mechanisms which generate EZs would help with understanding the possible importance of EZs in biology and in engineering applications such as filtration and microfluidics. Pollack theorizes that EZ water exists in a new phase which has a layered structure. We note several problems with Pollack's proposed structure, some of which were noted in the 1960's when a similar structure was proposed for ``polywater''. We argue that Schurr's diffusiophoresis based theory presents a compelling alternative explanation for the core EZ phenomena, although there remain other findings from Pollack's lab it does not explain. Among other things, Schurr's theory makes predictions about the growth of the EZ with time which have been confirmed by Florea et al.\ and others. In this work we also introduce and explore a novel hypothesis - that some aspects of EZ phenomena may be attributable to repulsive van der Waals forces. Finally, we touch on several possible confounding factors that make experimentation on EZs difficult, such as charged surface groups, dissolved solutes, and adsorbed nanobubbles.

The diagnostics of natural landscapes geoecological state in the course of the permafrost zone economic development should be based on the assessment of the destructive cryogenic processes formation. It is expedient to consider it in terms of landscapes resistance to cryogenic processes increase. The choice of lithocryogenic stability parameters is substantiated. These are: permafrost distribution over the area, its annual mean temperature and ice content, protective properties of the vegetation and etc. Cryogenic processes activation is estimated with regard to their area, development rate and attenuation, natural landscapes damage, hazard for engineering facilities operation. The assessment procedure, and the way of improving expert numerical scores are shown. At Geography Faculty of Lomonosov Moscow State University, the authors have developed a number of the approved methods of making evaluation maps of different scales applying the methods of landscape indication, modern methods of space images decoding, methods of expert scores, the method statistical calculations and methods of spatial GIS-analysis. The technique of Atlas geo-information mapping on the landscape basis has been introduced in seven atlases at scales from 1:3 000 000 to 1:20 000 000. These maps are widely used in design and survey organizations and in education.

The macro-litter (plastic) sea bottom pollution of 14 city harbors and marinas in North Africa and in the western Baltic Sea was investigated using a new simple mobile underwater camera system. The study was complemented by a harbor manager survey and 3D-hydrodynamic transport simulations. The average pollution in German marinas was 0.1 particles/m² sea floor (0.04–1.75). The pollution in North African marinas on average was 7 times higher (0.7 particles/m²) and exceeded 3 particles/m² in city center harbors. The resulting &gt;100,000 litter particles per harbor indicate the existence of a problem. With 73%-74%, plastic particles are dominating. Existing legal and management frameworks explain the lack of plastic bottles and bags on sea floors in Germany and are one reason for the lower pollution levels. Items that indicate the role of untreated sewage water were not found. Harbor festivals seem not to be quantitatively relevant for open sea bottom pollution. Our method tends to underestimate the pollution level. Model simulations indicate that storms can cause litter reallocations and sediment cleanings. However, marina sea floor monitoring is recommendable, because it addresses pollution hot-spots, is cost-effective and takes place close to emission sources. Further, the effectiveness of land-based pollution reduction measures can easily be assessed.

Plastic contamination is a burning issue costing the global cotton and textile industries billions of dollars annually. Any time plastics from different sources end up in a cotton lint bale, the value to the textile mills plummets significantly. Various industry players have therefore made a concerted effort to find lasting solutions to the menace posed by plastic to cotton profitability and sustainability. Nevertheless, until now, there have been no up-to-date comprehensive documents detailing the numerous and ever-growing efforts committed to solving this challenge. Therefore, this article provides a detailed yet compact review of this highly dynamic subject matter. First, it puts into perspective plastic contamination in the cotton and textile industries. Then, the cotton value chain is subdivided into phases from pre-cultivation to textile mills. The root causes of plastic contamination are discussed in each stage, followed by discussions of some already developed and emerging solutions in response to the challenge by the affected industries and researchers. Concluding from the author’s perspective, the paper makes projections for the future directions of plastic mitigation efforts within the cotton and textile industries. This article also infers from the reviewed literature that research on finding alternative materials to plastic as module wrap, the development of new, effective, and all-condition plastic sensing techniques for ginning and spinning equipment, and standardized protocols for UAV in-field surveys of plastic trash are some of the areas that will be beneficial to finding a permanent solution to the challenge.

The drastically increasing amount of plastic waste is causing an environmental crisis that requires innovative technologies for recycling post-consumer plastics to achieve waste valorization while meeting environmental quality goals. Biocatalytic depolymerization mediated by enzymes has emerged as an efficient and sustainable alternative for plastic treatment and recycling. A variety of plastic- degrading enzymes have been discovered from microbial sources. Meanwhile, protein engineering has been exploited to modify and optimize plastic-degrading enzymes. This review highlights the recent trends and up-to-date advances in mining novel plastic-degrading enzymes through state-of-the-art omics-based techniques and improving the enzyme catalytic efficiency and stability via various protein engineering strategies. Future research prospects and challenges are also discussed

To reduce the carbon emissions during heating in the manufacturing process, microwaves have attracted significant attention. Microwave has a lot of advantages rather than traditional heating method such as rapid heating, lower thermal damage and eco-friendly process. In order to apply microwaves to manufacturing process, uniform and efficient heating is required. We have analyzed the effect of various design parameters such as cavity heights, the application of the reflector, and the number and positions of waveguides for uniform and efficient heating by numerical simulation and verified that by experiment. The results showed that a slight change in the cavity height altered the electromagnetic field distribution and heating parameters, such as the coefficient of variance and power absorption efficiency. With reflectors installed, uniform heating was achieved and power absorption was improved, with the spherical reflector showing the maximum efficiency. The use of double waveguides heated the target material in a uniform manner. An increase in the power supply also led to uniform heating. This large-scale analysis will be helpful in applying microwaves to actual industrial sites.

Quite a number of new metered parking systems have been introduced in recent years by the local authorities of various spa towns in Poland in connection with home zone conversion projects. The traffic signs posted in these locations were limited to the beginning and end of the demarcated parking area. Traffic circle (TC) is an example of traffic calming measures (TCM) used in home zones to slow down the traffic (case study – home zone in a small spa village). This article presents the results of a study investigating the speed reductions obtained with a home zone and traffic circle used as traffic calming measures. The indispensable speed surveys were carried out in relation to this study in two periods: in summer when the streets are crowded with tourists and in September with little pedestrian traffic. Two research hypotheses were formulated as part of the speed data analysis to verify the slowing effect of traffic circle and the relevance of traffic circles design parameters and location, road function and the surrounding streetscape. For each hypothesis statistical analyses were carried out using two nonparametric tests: two-sample Kolmogorov–Smirnov test and median test. The third research hypothesis formulated in this study was related to sustainable development factors related to fuel consumption and traffic-related air pollution including carbon dioxide, carbon monoxide, nitrogen oxide and hydrocarbons. This hypothesis was verified by estimating the amount of air pollution in the home zone under analysis in three different situations (scenarios): in summer with the travel speed reduced by pedestrian traffic to ca. 8–10 km/h and in September with a small number of pedestrians and 20–25 km/h resulting speed between traffic circles, reduced at traffic circle, and in a theoretical 30 km/h zone with 25–30 km/h assumed speed between traffic circles, dropping at traffic circle. These analyses confirmed the appropriateness of traffic circle as a home zone traffic calming measure, as long as its design is based on a detailed analysis of the relevant factors, including location, road function and the surrounding streetscape.

Typhulaceae Jülich is one of the cold-adapted fungal families in basidiomycetes. Typhula (Pers.) Fr. and Pistillaria Fr. representing the family are distinguished from the morphology of a stipe to a hymenium (Fries 1821). The hymenium of Typhula is distinguishable from the stipe, but indistinguishable and consecutive in the genus Pistillaria. This taxonomic criterion is ambiguous, and consequently the opinion of Karsten (1882) has been widely accepted; I the genus Typhula, basidiomata develop from sclerotia, while basidiomata develop directly from substrata in the genus Pistillaris. But, Corner (1970) observed basidiomata of Pistillaria petasitis S. Imai in Hokkaido, Japan, from sclerotia. We collected irregular sclerotia of Typhula hyperborea H. Ekstr. from Upernavik, West Greenland. This specimen had a stipe-like structure on a Poaceae plant, and sclerotia developed on its tip. In August, P. petasitis in Hokkaido, Japan, formed basidiomata directly from substrates on the ground. Similar phenomena were found from other Typhula spp. in Japan. All of these fungi had the potential to produce sclerotia in culture, and as well as the capacity of mycelial growth at ambient air temperatures in each locality when samples were collected. These findings suggest that Typhula spp. developed basidiomata not only from the sclerotia dispersed by the basidiospores but also mycelia generated by the spore germination formed basidiomata multiple times depending on their growth environments.

Greenhouse have to provide optimal climate conditions for healthy plant growth and high production. Heating of greenhouses is required for an efficient and reliable production specially during winter time in Turkey. However, even in the temperate zones, heating costs has a great portion in the total production costs. Coal is preferred as a fuel in the greenhouse heating in provinces of Turkey where there is no geothermal energy. In this study, the heating requirements and fuel cost (fossil and geothermal energy) for Antalya, Afyon, Kütahya, Denizli, and Aydın provinces in the Aegean and Mediterranean region have been identified based on long term meteorological data. The calculations were made for two model greenhouses located in an area with 1 ha representing modern greenhouses of the regions. The first is a gothic roofed plastic model greenhouse and the second is a gable roofed polycarbonate model greenhouse. According to the results of calculations, total annual heatingrequirement values ranged from 6,096,283 (for Antalya) to 20,359,946 MJ/ha (for Afyon) for the plastic greenhouse wheras these values ranged from 3,187,074 (for Antalya) to 10,643,972 MJ/ha (for Afyon) for the polycarbonate greenhouse.

Current progress in the prediction of mechanical behavior of solids requires understanding of spatiotemporal complexity of plastic flow caused by self-organization of crystal defects. It may be particularly important in hexagonal materials because of their strong anisotropy and combination of different mechanisms of plasticity, such as dislocation glide and twinning. These materials often display complex behavior even on the macroscopic scale of deformation curves, e.g., a peculiar three-stage elastoplastic transition, the origin of which is a matter of debates. The present work is devoted to a multiscale study of plastic flow in α-Ti, based on simultaneous recording of deformation curves, 1D local strain field, and acoustic emission (AE). It is found that the average AE activity also reveals three-stage behavior, but in a qualitatively different way depending on the crystallographic orientation of the sample axis. On the finer scale, the statistical analysis of AE events and local strain rates testifies to an avalanche-like character of dislocation processes, reflected in power-law probability distribution functions. The results are discussed from the viewpoint of collective dislocation dynamics and are confronted to predictions of a recent micromechanical model of Ti strain hardening.

This article addresses the problem of contact voltage increase caused by the low frequency oscillation of the train-grid system in the phase-separation process of the EMU. The article establishes the EMU-contact line-traction substation model, reveals the mechanism of low-frequency oscillation, and obtains the relationship between the separation phase angle of the pantograph with line and low-frequency oscillations. Methods to suppress the over-voltage during the low-frequency oscillation are proposed. The study shows that when the power phase angle of the pantograph-line separation is within the range of 60°~90° and 240°~270°, the voltage amplitude in the neutral zone is larger, the maximum amplitude can reach 52.2kV, and low-frequency oscillation will occur in the neutral zone. When low frequency oscillation occurs, the contact line voltage in the neutral zone is mainly 1/3 power frequency (16.7Hz). After installing an RC suppression device in the neutral zone, when the EMU enters the neutral zone, the absolute value of the voltage peak drops to below 20 kV. Compared with the situation where the suppression device is not connected, the absolute value of the voltage peak is reduced by nearly 60%. The study provides a basis for the design of the neutral zone of the contact line and the selection of the high-voltage equipment of the EMU.

Ti17 alloy is mainly used to manufacture aero-engine discs due to its excellent properties such as high strength, toughness and hardenability. It is often subjected to creep-fatigue cyclic loading in service environments. Shakedown theory describes the state in which the accumulated plastic strain of the material stabilizes after several cycles of cyclic loading, without affecting its initial function and leading to failure. This theory includes three behaviors: elastic shakedown, plastic shakedown, and ratcheting. In this paper, the creep-fatigue tests (CF) were conducted on Ti17 alloy at 300℃ to study its shakedown behavior under creep-fatigue cyclic loading. Based on the plasticity-creep superposition model, a theory model that accurately describes the shakedown behavior of Ti17 alloy was constructed, and ABAQUS finite element software was used to validate the accuracy of the model. TEM analysis was performed to observe the micro-mechanisms of shakedown in Ti17 alloy. The results reveal that the Ti17 alloy specimens exhibit plastic shakedown behavior after three cycles of creep-fatigue loading. The established finite element model can effectively predict the plastic shakedown process of Ti17 alloy, with a relative error between the experimental and simulation results within 4%. TEM results reveal that anelastic recovery controlled by dislocation bending and back stress hardening caused by inhomogeneous deformation are the main mechanisms for the plastic shakedown behavior of Ti17 alloy.

Mechanical recycling of solid plastic wastes on a small-scale level can be accomplished with the correct approaches. Thermoplastics are mostly considered for mechanical recycling because of their physical properties and ease of reprocessing. This paper reviews the mechanical reprocessing techniques of selected thermoplastics (polyethylene terephthalate and polyolefins) since they constitute a significant proportion of plastics used commercially. Furthermore, necessary considerations for effective operation of small-scale plants, including energy requirements of machinery and optimisation in order to improve efficiency and product quality, are discussed. A clearer understanding and addressing of the process-related challenges will lead to successful establishment and management of small-scale mechanical recycling facilities to benefit communities. Efficient small-scale mechanical reprocessing establishments have become essential in reducing the environmental impacts of solid plastic wastes and for energy conservation.

The evolution of metals micro/nano-structure upon severe plastic deformation (SPD) is still far to be theoretically explained, while experimental datasets are persistently growing for several decades. Major problem associated with understanding of SPD is related to a fact that the latter is a synergetic product of several competing physical effects which alter the material micro/nano-structure. In attempt to find deformational boundaries, where predominantly one mechanism determines the micro/nano-structure, in this paper we propose a continuous piecewise model for the analysis of experiments on material hardness vs strain of SPD processed materials. The novelty of this approach lies in its ability to find, as free-fitting parameters, the strain breakpoints which separate different micro/nano-structure modes generated upon SPD process. The model is applied to analyse experimental data for polycrystalline samples of pure iron and two distinctive strain breakpoints are revealed with good accuracies. This finding is in a good agreement with our earlier results on TEM microscopy studies on pure iron polycrystals after SPD treatment.

An ionospheric response at middle latitudes to geomagnetic storms is not yet very well understood. Total electron content (TEC) variations associated with eight strong geomagnetic storms between 2015 and 2022 obtained from GNSS receivers in the western area of the North Atlantic (Portuguese continental and insular territory) are studied in an attempt to fill this gap. It was found that for most of the studied geomagnetic storms TEC variations are synchronous for the longitudinal ranges from 27ºW and 9ºW. In the southern part of the studied region (around 32ºN) the amplitude of TEC variations is, in general, significantly higher than in the northern part (around 39ºN). Some of the studied geomagnetic storms were associated with TEC variations that we interpret as effects of post-sunset equatorial plasma bubbles that travelled well north from their habitual region. Also, while most of the studied storms were accompanied by reports on different kind of malfunction of GNSS systems (GPS; GALILEO and other), there is no clear pattern in their appearance in dependence on the geomagnetic/ionospheric storms’ strength, commencement time, and its characteristics, in general.

Nanoindentation load-depth (P-h) plots is the basis for determination of mechanical properties of the samples and is especially vital for thin coatings deposited on substrates of various mechanical makeup from amorphous-brittle (borosilicate glass) to Silicon (having different crystallographic texture) to ductile substrates like stainless steel as well other aspects like indenter tip shape. The elastic-plastic response by simulated P-h plots as per modified empirical relations have been presented. The outcomes of this computational studies enlighten the database on the P-h plots for various coating/substrate systems and shall aid in the analysis of experimental P-h plots obtained,

Plastic poses a significant threat to the environment, polluting land, water, and air. It is a broad term encompassing a variety of polymers. In the form of microplastics and nanoplastics, it can induce toxicity in water bodies. Plastic debris not only physically pollutes freshwater, but also chemically, undergoing changes over time due to hydroclimatic effects. Rivers serve as conduits, transporting plastics from minor tributaries to major rivers and ultimately into the ocean, endangering marine life. India, as a developing country with the largest population and numerous rivers, generates a significant amount of plastic waste, a substantial portion of which finds its way into rivers, leading to alarming rates of plastic accumulation in the ocean. Previously, policymakers focused primarily on landfills for plastic waste, neglecting the pollution of water bodies. The consequences of this neglect are evident, with major rivers in the country severely affected by plastic waste, necessitating advanced, efficient, and sustainable solutions. This study aims to establish a comprehensive framework for managing plastic waste, understanding its transport mechanisms to the ocean, and recognizing the threats it poses to life. It also expounds on harmful plastic pollutants in water, globally adopted technologies, and emphasizes the need for further research and data collection in this field. The primary concluding point is to prevent plastics from entering waterways and to actively collect river and marine plastic pollution. Banning single-use plastics and implementing efficient collection methods are crucial in containing plastic pollution. Effluents from industries should not be overlooked, as they often contain harmful micro and nanoplastics with ecotoxicological effects. The innovative concept of the "4Rs" - Refuse, Reduce, Reuse, and Recycle - stands as the cornerstone for safeguarding the environment against plastic pollution.

Plastic waste management has become a major problem in the present times, and many countries are struggling to deal with it. The situation has become a crisis in developing nations due to a lack of proper waste management, resources, technology, and political will. The extensive usage of foam-based packaging materials such as Styrofoam as a secondary packaging material has led to environmental pollution both in land and water, in developing countries. It is important to address this problem using a sustainable approach such as biomimetic manufacturing. One such solution that is present in developed nations is mycelium-based packaging, wherein the agricultural and industrial-based cellulose waste is converted into a biocomposite with the help of a fungi root network. Such a process has the potential to convert biomass into useful products but also has an indirect effect on pollution reduction by eliminating stubble burning in nations like India. In this review, we examine the details of the manufacturing process, properties, advantages, and limitations of such composite materials. A comparison of the present status of such materials produced in the market by some of the companies across the world is presented. Finally, the challenges involved with such materials and the future directions are discussed.

In this paper, an incremental eqivalent contact model is developed for elastic-perfectly plastic solids with rough surfaces. The contact of rough surface is modeled by the accumulation of circular contacts with varying radius, which is estimated from the geometrical contact area and the number of contact patches. For three typical rough surfaces with various mechanical properties, the present model gives accurate predictions of the load-area relation, which are verified by direct finite element simulations. An approximately linear load-area relation is observed for elastic-plastic contact up to a large contact fraction of 15%, and the influence of yield stress is addressed.

The Covid-19 coronavirus, SARS-CoV-2, is inactivated much faster on paper (3h) than on plastic (7d). By classifying materials according to virus stability on their surface, the following list is obtained (from long to short stability): polypropylene (mask), plastic, glass, stainless steel, pig skin, cardboard, banknote, cotton, wood, paper, tissue, copper. These observations and other studies suggest that SARS-CoV-2 may be inactivated by dryness on water absorbent porous materials but sheltered by long-persisting micro-droplets of water on waterproof surfaces. If such physical phenomenons were confirmed by direct evidence, the persistence of the virus on any surface could be predicted, and new porous objects could be designed to eliminate the virus faster.

The purpose of this work is to optimize angular extrusion for sever plastic deformation of tubular specimens. A finite element model (FEM) was built in Deform-3D^® for three extrusion dies and analyzed. The dies were ECAP (135°), TCAP with external groove of 90° (denoted as TCAP-e) and TCAP with internal groove of 90° (denoted as TCAP-i). The analysis for process parameters (such as coefficient of friction-μ, die angles-ѱ and φ, temperature - T, and radius ratio-R) showed that TCAP-i was the optimal die in processing Al6063 tubes based on strain and load distribution of the model. The TCAP-i die model was further optimized for different parameters namely die angles, coefficient of friction, deformation ratio and temperature. The results showed that at constant process temperature of 25 °C, the optimal TCAP-i has the following parameters: φ₂=80⁰, Ѱ₁=30⁰, Ѱ₂=80⁰, Ѱ₃=30⁰, μ =0.4 and R =1.5.

This study explores the relationship between mental and physical therapeutic through three dimensions: man-environment relationships; a sense of place and symbolic landscapes. The study used a combination of qualitative and quantitative research methods. Local residents living in the coastal area of Xinglin Bay are the research objects. Quantitative data analysis revealed that the frequency of residents' visits was an important variable affecting their physical and treatment perceptions. In addition, the significance is higher for females than for males. The text analysis shows that the environment, especially the ecological restoration of water quality and migratory birds, is of great significance to the identity of local residents. Daily activities contribute to a sense of place and are what make the coast a place of therapeutic landscape function.

The Tisza River is the longest tributary of the Danube, draining the eastern part of the Carpathian Basin (Central Europe). Five countries share its catchment with different waste production and management practices. Large amounts of waste, including macroplastics (MaPs), are washed into the river. Some of the litter is trapped by the riparian vegetation forming litter accumulations. The study aimed to map the amount of litter by a citizen science program and remote sensing data and to compare the MaP data to the amount of microplastic fragments in sediments. Volunteers reported 3216 riverine litter accumulations from five countries along the entire length of the Tisza (2016–2022). The results suggest that low flow conditions (e.g., impoundment by dams) support litter and MaP trapping. The volume of large accumulations registered by the citizens showed a good correlation with the area of drifting litter revealed on Sentinel-2 images (2015–2021) using machine learning algorithms. Though the MaPs probably fragmentate during their fluvial transport, no clear connection was found between the volume of litter accumulations and the mean microplastic fragment content of sediments (2019–2022). The “Clean Tisza Map“ reveals the high degree of stranded pollutants along rivers and supports public cleanup activities.

The strength of laser joined metal and plastic hybrids is based purely on adhesion. Unpolar plastics like polypropylene depend solely on the mechanical adhesion while polar plastics like polyamide 6.6 develop covalent bonds with the metal. In this research the influence of different surface metallizations on the lap shear strength of laser joined hybrids was investigated. Sandblasted AISI 304 was used as base metal and reference. Aluminum and titanium coatings were deposited by the means of Arc-PVD. Polypropylene and polyamide 6.6 were utilized as polar und unpolar plastics. The lap shear strength of all hybrids with polyamide 6.6 was higher than the polypropylene samples. For all investigated variations of the laser power, scanning speed and the cohesive and adhesive failure modes, the samples joined with the sandblasted AISI 304 showed the highest lap shear strength. The reduction in lap shear strength for the coated samples was due to the increased difference in thermal conductivity between the plastics and the coating materials. This lead to increased warping and residual stresses. It can be concluded that the thermal properties of the metallization in laser joined metal and plastic hybrids has a high impact on the lap shear strength.

The scope of this paper is to use plastic waste through the gasification process for producing electricity with low carbon dioxide emissions. Worldwide, plastic production increased, reaching 367 million tons in 2020, compared with 1.5 million tons in 1950. It is known that plastic incineration generates approximately 400 million tons of CO2 annually, and consequently, new solutions for a more efficient plastics reuse in terms of emissions generated are still expected. One method is to use plastic waste in a gasifier unit and the syngas generated in a gas turbine for electricity production. The co-gasification process (plastic waste with biomass) was analysed in different ratios. Gasification was carried out with air for an equivalent ratio (ER) between 0.10-0.45. The volume concentration of CO2 in syngas ranged from 2-12%, with the highest value obtained when poplar content in the mix was 95%. In this study, the option of pre- and post-combustion integration of the chemical absorption process (CAP) was investigated. Thus, CO2 emissions have decreased by 90% compared with the case without CO2 capture. By integrating the capture process, the global efficiency has reduced with 5.5 – 6.1 percentage points in a post-combustion case, according to the plastic content in the mix.

Water management and soil pollution are hot issues in modern agriculture. While more production of food is required, this quantity has to be obtained using the minimum level of resources and the maximum amortization of assets. Moreover, studies show that in Europe, 30% of water consumption is for agriculture, which has a strong influence not only on the amount of water consumed, but also on its quality due to pollution caused by chemical fertilizers, pesticides and other pollutants used in this sector. Therefore, a major concern is related to the use of water, its efficient consumption, which requires optimal irrigation systems both in terms of water transport and distribution. In this context, but also in the context of a turbid environmental debate, the most important facts in agriculture are the protection of the environment on a long range of time. In order to obtain good results for an irrigation system, in this paper we will present a model for calculating the best suited material for a given geographical area and the optimal water content for irrigation

Plastic waste accumulation poses significant environmental challenges, underscoring the importance of closing the plastic life cycle by converting waste into valuable products. Pyrolytic char, a promising byproduct, offers diverse industrial applications. However, little attention has been given to converting hydrocarbon-based plastics into solid carbon due to their low fixed carbon content. This study compares sulfonation and thermal oxidation stabilization techniques for carbonizing waste polyethylene and polyvinyl chloride. Results indicate sulfonation yields higher pyrolytic char formation and improves surface properties, surpassing Al2O3 in catalyst support characteristics. Thermal oxidation increases fixed carbon content but adversely affects char yield and surface properties. Both methods effectively enhance fixed carbon content, but sulfonation emerges as more advantageous, suggesting potential use of plastic-derived char as a catalyst support material, contributing to circular economy development.

The merge areas of freeway work zones include relatively significant safety hazards that have continuously led to urgent safety issues to be solved by the management departments. In order to make up for the cumbersome process of independent identification of rear-end collision and lane change collision on complex road sections, an appropriate identification method of traffic conflicts in the merge area of freeway work zone was explored, this study collected vehicle running tracking data from the merge areas of multiple work zones, using an unmanned aerial vehicle video technique. Based on an inter-frame difference method and the principle of a spatio-temporal context visual tracking algorithm, the vehicles were detected and tracked, and the coordinate data of the vehicles in continuous motion were parsed using MATLAB extension tools. Based on the behavior characteristics of vehicle conflict avoidance, a new identification method for evading severe traffic conflicts is proposed according to the initial velocity, acceleration and accident rate of section traffic. Then, a statistical analysis was performed on the spatial distribution characteristics of the traffic conflicts in typical merge areas. The impacts of the road conditions in work zones, vehicle factors, and traffic flow factors on the traffic conflicts were analyzed. A binomial logistic model was established to identify the main influencing factors. The results show that in the merge area of the freeway work zone, there are serious traffic conflicts between vehicles in the following two situations: (Ⅰ) v∈[7,13.5] m/s and a∈[-3.96,-0.65]m/s2; and (Ⅱ) v∈[13.5,24.3] m/s, and a∈[-3.96,-1.57] m/s2. The probabilities of serious traffic conflicts in the first and last 25 m of the merge area are greater than those in the other sections. The smaller the space between the upstream work zone and the merge area, the greater the probability of serious traffic conflicts between vehicles. When the average vehicle speed is relatively high, the probability of serious conflicts is the highest, i.e., by a multiple of 5.95 from the baseline. Moreover, the probability of serious conflicts between vehicles is higher for larger vehicles, i.e., 4.765 times that for small vehicles. The research results can serve as a reference for freeway management departments to improve the safety levels of merge areas during road work. For example, the probability of serious conflicts can be effectively reduced by setting up reasonable speed limit signs in the work zone, increasing the spacing between work zone and merge area, and appropriately diverting large vehicles.

Linear elastic fracture modeling coupled with empirical material tension data result in good quantitative agreement with experimental measurements of fracture failure for both brittle and tough epoxy nanocomposites. The nanocomposites comprise diglycidyl ethers of bisphenol A cured with O,O’ bis (2-aminopropylpropylene glycol) (Jeffamine D230) and doped with rubber nanoparticles of varying concentrations. Toughness, critical load, and critical displacement in quasi-static single edge-notched three-point bending are predicted accurately using both surface-based cohesive zone (CZS) and extended finite element (XFEM) methods implemented in Abaqus software. Fracture initiation within a crack is taken at the yield stress from uniaxial tension data. Prediction of fracture processes using a generalized truncated linear traction-separation law was significantly improved by considering the case of a linear softening function. There are no adjustable parameters in the XFEM model. The CZS model requires only optimization of the element displacement at fracture parameter. Thus, these continuum methods describe these materials in mode I fracture with a minimum number of independent parameters.

The association between autoimmune diseases, mostly rheumatoid arthritis, systemic lupus erythematous, celiac disease and Sjögren syndrome, and lymphoma has been widely demonstrated by several epidemiologic studies. By a not yet entirely elucidated mechanism, chronic activation/stimulation of the immune system, along with the administration of specific treatments, may lead to persistent stimulation of both of B- and T-cells, and to the onset of different types of lymphoma in such patients. Specifically, patients affected by may develop lymphomas may years after the original diagnosis. Several epidemiologic, hematologic and histological factors may anticipate the progression from Sjögren syndrome into lymphoma but, to the best of our knowledge, a definite pathogenetic mechanism for such progression is still missing. In fact, while the association between Sjögren syndrome and non-Hodgkin lymphoma, mostly diffuse large B-cell and extranodal marginal zone lymphomas is well established, many other variables, such as time of onset, gender predilection, sites of occurrence, subtype of lymphoma and predictive factors still remain unclear. We report on a rare case of primary breast lymphoma occurring three years after the diagnosis of Sjögren syndrome in a 57 y.o. patient. The diagnostic work-up, including radiograms, core needle biopsy and histological examination are discussed, along with emerging data from the recent literature, thus highlighting the usefulness of breast surveillance in Sjögren syndrome patients.

The paper presents the basic structural parts, a 3D model and the overall design of a laboratory machine, which was created to detect vibrations generated by the casing of a conveyor roller ro-tating at different speeds. The intention of the authors was to verify whether plastic brackets in-serted into the structurally modified trestles of a fixed conveyor idler can reduce the vibration values transmitted from the rotating conveyor roller to the trestle of a fixed idler. Experimental vibration measurements taken on the non-rotating parts of conveyor rollers, performed on a laboratory machine according to ISO 10816, are suitable for characterizing their operating condi-tions with regard to trouble-free operation. The aim of this paper is to detect the vibrations of a rotating conveyor roller on a laboratory machine in the defined places of a fixed conveyor idler and also on the steel frame of a laboratory machine that represents the supporting track of a belt conveyor. Vibrations detected by piezoelectric acceleration sensors were recorded by a measur-ing apparatus and displayed in the environment of Dewesoft X software. The measurements show that the vibration values grow with the increasing speed of the conveyor roller rotation. Experimental measurements have proven the correctness of the assumption that the vibrations transmitted to the trestle of a fixed conveyor idler are lower by up to 40% when using plastic brackets into which the axle of the conveyor roller is attached, compared to the solution where the axle of the conveyor roller is inserted into the notches of a steel trestle.

In this work we produced biochar by coffee waste and use it as filler in epoxy resin composite with the aim to increase their electrical properties. The biochar and biochar based composite electrical conductivity were studied in function of applied pressure and compared with carbon black and carbon black composite. The applied pressure has the aim to investigate the behaviour of filler in powder or dispersed in composite in function of compression. Results showed that even if the coffee biochar has less conductivity if compared with carbon black in powder form, it has better conductivity in composite if compared with carbon black. Composite mechanical properties were tested and they are generally improved respect to neat epoxy resin.

Plastics play a pivotal role in the principles of a circular economy, where their effective recycling post-utilization, leading to economic value generation and minimal environmental harm, is crucial for achieving sustainable management. Extensive research has delved into the incorporation of waste plastics in concrete, showcasing promising outcomes with a myriad of advantages..The escalating volume of plastic waste is becoming a pressing issue, contributing to environmental pollution, particularly in densely populated cities and towns in Nigeria such as Delta, Aba, Port Harcourt, Onitsha, Enugu, Benue, and Ogun. These urban centers experience high consumption of goods packaged or sealed in plastic materials. Tourist destinations are also affected as large quantities of plastic waste are improperly disposed of or incinerated, resulting in environmental contamination and air pollution. Efforts to address this growing concern are crucial to safeguarding the environment and public health in these regions.Therefore, it is imperative to find effective ways to utilize these waste plastics. By cleaning low-density polyethylene bags and combining them with sand at specific proportions, high-strength bricks can be produced. These bricks not only exhibit thermal and sound insulation properties but also help in pollution control and cost reduction in construction projects. This innovative approach not only addresses the issue of accumulating plastic waste, a non-biodegradable pollutant, but also offers a sustainable solution to manage plastic waste while contributing to the construction industry's efficiency and environmental protection., By incorporating waste plastic and nylon into brick production, we not only reduce the amount of sand extracted from our natural resources like rivers and seas but also utilize the surplus plastic waste that is currently discarded. This research focuses on creating eco-friendly bricks by incorporating molten plastic, nylon, and plastic bottles in varying percentages (0 to 15% by weight) along with 5kg of fly ash. The experimental results from this study will shed light on the feasibility and benefits of using these materials in brick manufacturing, highlighting the potential of sustainable construction practices that minimize environmental impact and resource depletion, The experimental process involved utilizing cement and sand to complete the brick composition, with curing conducted underwater for 29 days followed by baking at temperatures between 100°C to 120°C for 2 hours. The resulting eco-friendly bricks exhibited key characteristics such as being lightweight, porous, having low thermal conductivity, and displaying appreciable mechanical strength. Interestingly, the compressive strengths of these bricks, post the addition of waste plastic and nylon, were found to be comparable to that of conventional bricks. Additionally, these eco-friendly bricks showcased reduced water absorption capacity compared to regular bricks, offering a promising alternative for sustainable and efficient construction practices.The eco-friendly bricks made from A, B, C, and D using 0%, 5%, 10%, and 15% plastic/nylon waste showed comprehensive strengths of 19.5 ,19.46, 20.3, and 21.1 respectively, with corresponding water absorption percentages of 0.34, 0.25, 0.22, 0.20, and 0.085. The efflorescence values were lower than those of normal bricks. These bricks are likely to enhance energy efficiency in buildings and provide economic value to manufacturers, thereby promoting a sustainable ecosystem for plastic waste management with the involvement of all stakeholders.

This paper presents the results of experimental and numerical investigations aimed at enhancing the flexural capacity of Precast Concrete Corbel Beam-Column Connections (PC-CBCC) using Fiber-Reinforced Plastic (FRP) sheets. The experimental study primarily focused on assessing the flexural capacity of pinned PC-CBCCs reinforced with FRP layers, comparing them to a moment-resisting connection. A series of half-scale specimens, including three PC-CBCCs with varying FRP configurations, were tested alongside one in-situ concrete fixed connection. The objective was to quantify the ultimate flexural capacity of PC-CBCCs reinforced by FRP sheets. The effects of FRP layer thickness, locations, and potential debonding were examined under unidirectional static tests while applying a constant axial compressive load to the columns and subjecting the beams to lateral loads until fracture. Additionally, a precise finite element model of the PC-CBCCs and a fixed joint was developed and verified to simulate nonlinear static analyses of the connections in ANSYS software. A comprehensive comparison was conducted to determine their responses by employing various FRP configurations and properties. The tests and numerical results demonstrate that wrapping PC-CBCCs with anchored FRPs can transform pin connections into moment-resistant joints. Moreover, critical design parameters such as bond length, thickness, and placement of FRP sheets, along with appropriate mechanical anchorage, are identified to prevent debonding and delamination.

Due to growing concerns about environmental pollution from plastic waste, plastic recycling research is gaining momentum. Traditional methods, such as incorporating inorganic particles, increasing cross-linking density with peroxides, and blending with silicone monomers, often improve mechanical properties but reduce flexibility for specific performance requirements. This study focuses on synthesizing silica nanoparticles with vinyl functional groups and evaluating their mechanical performance when used in recycled plastics. Silica precursors, namely sodium silicate, and vinyltrimethoxysilane (VTMS), combined with a surfactant, were employed to create pores, increasing silica's surface area. Early-stage introduction of vinyl functional groups prevented the typical post-synthesis reduction in surface area. Porous silica was produced in varying quantities of VTMS, and the synthesized porous silica nanomaterials were incorporated into recycled Polyethylene to induce cross-linking. Despite a decrease in surface area with increasing VTMS content, a significant surface area of 883 m2/g was achieved. In conclusion, porous silica with the right amount of vinyl content exhibited improved mechanical performance, including increased tensile strength, compared to conventional porous silica. This study shows that synthesized porous silica with integrated vinyl functional groups effectively enhances the performance of recycled plastics.

The rapid development in industries manufacturing plastic bags is taking serious consideration to save the environment and human health, one way or the other. This study examines the composition of degradable and non-degradable plastic bags collected from the markets of different sectors of Islamabad. Hundred samples of both Degradable and non-degradable plastic bags were collected from the open market. The concentrations, proportion, and patterns of different heavy metals (additives) were used in the production of both degradable and non-degradable plastic bags by using the standard method with the help of Hands Held X-Ray Fluorescent (HHXRF) instrument. Samples results of the study showed Titanium, Calcium and Copper used in massive amounts, some of the toxic metals i.e., Arsenic, Lead, Cadmium, Chromium and Mercury were also detected. This study also reveals that degradable plastic bags might be more hazardous than non-degradable plastic bags because due to the Photolytic properties of additives used in degradable plastic bags when the chains of polymers break, the heavy metals are released in environment and become the part of it. So, concern department like Ministry of climate change and Pakistan Environmental Protection Agency should take serious step to control these serious issues.

A series of Ti₄₀Zr₂₅Cu₉Ni₈Be₁₈)_100-xTM_x (x = 0, 1, 2, 3, 4 at.%, TM = Nb, Y) Bulk amorphous alloys were designed and prepared using the copper mold casting method. The microstructures, glass forming ability and mechanical properties of the alloys were investigated by means of X-ray diffractometry (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), differential scanning colorimetry (DSC), depth-sensitive nanoindentation and uniaxial compressive test. The Bulk amorphous alloys with different ductility were investigated by measuring their plastic deformation energy (PDE) of the first pop-in events during loading. The relationships between the PDE value, shear band formation and ductility in Bulk amorphous alloys have been investigated. The results show that the PDE value decreases by the Nb addition and promotes the generation of multiple shear bands easily, which increase the fracture strength and plasticity significantly. Substituting Nb with Y has exactly the reverse effect. A useful rule for preparing of Bulk amorphous alloys with high plasticity is herein proposed, whereby the chemical composition of the Bulk amorphous alloys can be tailored to possess a lower PDE value.

Abstract: The ongoing use of plastic polymers to manufacture food packaging has raised concerns about the presence of nano- and microplastics (NMPs) in a variety of foods. This review provides the most recent data on NMPs' migration from plastic packaging into milk and dairy products. Also discussed are the possible effects of NMPs on nutrient digestion, absorption, and metabolism. Different kinds of milk products, including skimmed or whole liquid and powder milk, infant formula milk, and other dairy products, have been found to contain NMPs of various sizes, shapes, and concentrations. NMPs may interact with proteins, carbohydrates, and fats and have a detrimental impact on how well these nutrients are digested and absorbed by the body. The presence of NMPs in the gastrointestinal tract may impact how lipids, proteins, glucose, iron, and energy are metabolised, increasing the risk of developing health conditions such as diabetes, cardiovascular disease, hypertension, and some cancers. In addition to NMP, plastic oligomers released from food packaging material have been found to migrate to various food simulants and milk, though their effect on human health has yet to be investigated. Viewpoints on potential directions for future studies on NMPs and nutrient digestion, absorption, and health are also presented in this review.

Abstract: A two-year study of pearl millet-groundnut cropping systems across two fertilizer levels was conducted at the INRAN/TARNA research station in Maradi, Niger in the Sahelian zone of West Africa. The objective of this study was to identify the best cropping system with and without fertilizer application to optimize pearl millet and groundnut yields, land use efficiency, and economics as measured by value-to-cost ratio. The experiment was conducted with three replications, and ten treatments combination of five pearl millet and groundnut cropping systems (pearl millet and groundnut sole crops, and three pearl millet – groundnut intercrops), and two fertilizer levels. Sole cropping produced the highest pearl millet grain by over 300 kg ha-1 and groundnut pod yields by over 500 kg ha-1, but all the intercropping systems had a LER above 1.0 with land use efficiency increased by 19 to 41%, also intercropping increased diversity, and reduced risk. Fertilizer application increased yields in all cropping systems by 200 to 600 kg ha-1. Government subsidy increased the value-to-cost ratio by 0.5 to 2, 5 units, and was required for economic response for pearl millet sole and intercrops in 2022. The groundnut sole cropping system had the greatest economic response to fertilizer application. Based on the risky environment and multiple end uses needed by producers, the intercrop system M-G: 1:3:1 with fertilizer application is usually the best option to optimize pearl millet and groundnut production.

Landslide is one of the most common geological disasters in China, which is characterized by suddenness and uncertainty, and it is difficult to realize accurate identification, early warning and forecasting of landslide disaster by conventional means. With the development of high-resolution remote sensing satellites and InSAR surface deformation monitoring technology, the traditional means of landslide monitoring data sources are limited, and there is a lack of effective methods to excavate the characteristics of the spatial distribution of landslide hazards and their triggering factors and other issues. In this paper, the area extending 10 km outside the VII isobar of the Gengma earthquake is taken as the study area, and 13 evaluation factors are screened out by integrating the factors of InSAR surface deformation, topography and geological environment, and the Bayesian Optimized Convolutional Neural Network (BO-CNN) is used for the evaluation of landslide susceptibility, and the BO-RF and PSO-SVM models are selected for the comparative analysis. The model accuracy evaluation was carried out by three indexes: ROC curve, AUC value and FR value, in which the ROC curves of PSO-SVM, BO-RF and BO-CNN were all close to the upper-left corner of the corner, and the AUC values were 0.9388, 0.9529, and 0.9535, respectively, and the FR value of landslide in the high susceptibility area of BO-CNN was as high as 14.9, and was higher than that of PSO-SVM and BO-RF, respectively. SVM and BO-RF model is 4.55 and 3.69 higher, the experimental results show that the BO-CNN model used in this paper has a better effect in landslide susceptibility evaluation, and the research results of the local government's disaster prevention and mitigation measures are of great significance.

The odontogenic cysts can lead to a bone destruction that can hamper the dental implant place-ment in the ideal 3D position. Different biomaterials and techniques that allow bone regeneration are described in the literature, each with its advantages and disadvantages. This clinical case with 18 months of follow-up shows the enucleation of an odontogenic cyst fol-lowing the guide bone regeneration with fence technique. After 6 months 2, dental implants were placed at the region of tooth 11 and 21, being rehabilitated nine weeks after. The fence technique allowed the recovery of the bone morphology and the placement of the dental implants in the 3D ideal position.

Hydraulic fracturing for oil-gas and geothermal reservoir stimulation is closely related to the generation and propagation of Mode I crack. Nonlinear deformation due to rock heterogeneity occurs at such crack tip, which causes the fracture process zone (FPZ) to form before the crack propagates unsteadily. However, the relationship between the FPZ characteristics and rock heterogeneity still remain elusive. We used three rock types common in reservoir for experimental investigation, and each of them includes two subtypes with different heterogeneity due to grain size or microstructural characteristics. Drawing on the experiment results, we calculated the FPZ size in each cracked chevron notched Brazilian disk, and we reproduced the formation process of the FPZ in marble by discrete element method. We showed that strong heterogeneity is favorable to large FPZ size, can enhance the ability of crack generation and complicate crack morphology. Coupling the Weibull distribution with fracture mechanics, the dependence of the FPZ size on heterogeneity degree can be theoretically explained, which suggests that inherent heterogeneity of rocks set physical foundation for formation of FPZ. These findings can improve our recognition to formation mechanism of the Mode I crack and provide useful guidelines for evaluating reservoir fracability.

The Greenland Ice Sheet is now the largest land ice contributor to global sea level rise, largely driven by increased surface meltwater runoff from the ablation zone, i.e. areas of the ice sheet where annual mass losses exceed gains. This small but critically important area of the ice sheet has expanded in size by ~50% since the early 1960s, and satellite remote sensing is a powerful tool for monitoring the physical processes that influence its surface mass balance. This review synthesizes key remote sensing methods and scientific findings from satellite remote sensing of the Greenland Ice Sheet ablation zone, covering progress in 1) radar altimetry, 2) laser (lidar) altimetry, 3) gravimetry, 4) multispectral optical imagery and, 5) microwave and thermal imagery. Physical characteristics and quantities examined include surface elevation change, gravimetric mass balance, reflectance, albedo, and mapping of surface melt extent and glaciological facies and zones. The review concludes that future progress will benefit most from methods that combine multi-sensor, multi-wavelength, and cross-platform datasets designed to discriminate the widely varying surface processes in the ablation zone. Specific examples include fusing laser altimetry, radar altimetry, and optical stereophotogrammetry to enhance spatial measurement density, cross-validate surface elevation change, and diagnose radar elevation bias; fusing optical imagery, radar imagery, and microwave scatterometry to discriminate between snow, liquid water, refrozen meltwater, and bare ice near the equilibrium line altitude; combining optical reflectance with laser altimetry to map supraglacial lake, stream, and crevasse bathymetry; and monitoring the inland migration of snowlines, surface melt extent, and supraglacial hydrologic features.

Solar pasteurization, as a means of treating milk in remote rural areas without electrical power, is based on using solar energy to thermally inactivate pathogenic microorganisms at temperatures below the boiling point to maintain or improve milk quality. A solar milk pasteurizer of flat‐plate water‐heating glass acting as the solar collector, connected to a stainless-steel cylindrical milk vat, was constructed and evaluated in Navrongo, in the tropical savanna zone of Ghana, West Africa. The novel approach taken in this project is to integrate the solar collection and heat exchanger into a single unit using materials and fabrication techniques readily available in the developing world. The vat comprises a 1.5 mm thick stainless steel cylindrical tank, a 2.2 cm wide hot water jacket, and an outer layer of 5.0 mm thick aluminium foil insulation. Hot water produced by the collector was used for pasteurizing milk. The optimum quantity of milk that this device could pasteurize under the study conditions was 8 L. The device could pasteurize raw milk to a maximum temperature of 74 °C at 14:00 h GMT. The ambient temperature during the pasteurization ranged from 30 °C to 43 °C. The microbial analysis before and after the pasteurization was done, and the result shows that the total bacteria count before pasteurization was 6.6x10⁶ log CFU/mL per unit volume, and the total bacteria count after pasteurization was 1.0x10² log CFU/mL. By acceptable standards, the total bacteria count after pasteurization is within a safe range for consumption, and coliform counts were negative. The solar milk pasteurization system is cost-effective. Hence, it is appropriate for milk producers in arid pastoral areas without electricity to adopt the solar pasteurizer as an alternative to firewood as a fuel source for milk pasteurization. This approach can potentially create a cottage industry that may also play a crucial role as a water treatment technology that will improve the health of rural populations.

Quantity-intensity characteristics are among conventional approaches for studying potassium dynamics and its availability; this was assessed to determine availability in four districts: namely, Sodo Zuria, Damot Gale, Damot Sore, and Boloso Sore at three different land use type viz., enset-coffee, crop land, and grazing land. There was water soluble, ammonium acetate, nitric acid extractable potassium, exchangeable potassium, and non-exchangeable potassium studied in soil samples, which were collected from 0-20 cm depth of each land type. The study revealed that water soluble and ammonium acetate extractable potassium concentrations ranged from 0.04 to 0.42 cmolKg-1 soils enset-coffee and grazing land use types, respectively. The study showed that exchangeable potassium constituted the highest proportion of available potassium, while the proportion of water soluble potassium was found to be the lowest. In this study, non-exchangeable potassium concentrations varied from 0.10 to 0.04cmolKg-1soils for enset-coffee, and crop and grazing land use type. Furthermore, available potassium and exchangeable potassium concentrations were positively correlated with OC(r=0.95***), cation exchange capacity, and sand and clay(r=0.98***). In addition, the K dynamics as impacted by land use types found that the highest change in exchangeable potassium (0.31cmolkg-1soils) and potential buffering capacity (1.79cmolkg-1soils) were noted in crop land use types, whereas the lowest change(1.26cmolkg-1 soils) was observed in the enset-coffee system, The varying properties, potassium status, dynamic and land use type of soils identified in the study areas provided adequate information to design soil potassium management options and further research about the soil in each site. Therefore, application of site specific soil fertility management practices and research can improve soil potassium status and quantity intensity parameters to sustain crop productive soils.