This paper numerically investigates a 3D mesh independency study of a straight blade horizontal axis tidal turbine modelled using Computational Fluid Dynamics (CFD). The solution was produced by employing two turbulence models, the standard k-ε model and Shear Stress Transport (SST) in ANSYS CFX. Three parameters were investigated: mesh resolution, turbulence model, and power coefficient in the initial CFD, analysis. It was found that the mesh resolution and the turbulence model affect the power coefficient results. The power coefficients obtained from the standard k-ε model are 15% to 20% lower than the accuracy of the SST model. It can also be demonstrated that the torque coefficient increases with the increasing Tip Speed Ratio (TSR), but drops drastically after TSR = 5 and k-ε model failing to capture the non-linearity in the torque coefficient with the increasing TSR.

Point-contact spectroscopy has been performed on bulk samples of electron-doped high temperature superconductor Nd2-xCexCuO4-. The samples were characterized by X-ray diffraction and scanning electron microscopy equipped with a wavelength dispersive spectrometer and an electron backscatter diffraction detector. The samples with a Ce content x = 0.15, show the absence of spurious phases and randomly oriented grains, most of which have dimensions of approximately 220 µm2. The low-bias spectra in the tunnelling regime, i.e., high transparency interface, exhibit a gap feature at about ±5 meV and no zero-bias conductance, consistent with the most literature data on oriented samples. The high-bias conductance has also been measured in order to obtain information on the properties of the barrier. A V-shape has been in some cases observed, instead of the parabolic behavior expected for tunnel junctions.

Inexpensive piezoelectric diaphragms can be used as sensors to facilitate both nozzle height setting and build platform leveling in FFF (Fused Filament Fabrication) 3D printers. Tests simulating nozzle contact are conducted to establish the available output and an output of greater than 8 Volts found at 20 ºC, a value which is readily detectable by simple electronic circuits. Tests are also conducted at a temperature of 80 ºC and, despite a reduction of greater than 80% in output voltage, this is still detectable. The reliability of piezoelectric diaphragms is investigated by mechanically stressing samples over 100,000 cycles at both 20 ºC and 80 ºC and little loss of output over the test duration is found. The development of a nozzle contact sensor using a single piezoelectric diaphragm is described.

The SARS-CoV-2 pandemic has resulted in the generation of evolutionary-related variants. The S-protein of the B.1.1.7 variant (deletion N-terminal domain (NTD) His69Val70Tyr144) may contribute to altered infectivity. These mutations may have been presaged by animal mutations in minks housed in mink farms that according to the present analysis by modelling of protein ligand docking altered a high affinity binding site in the S-protein NTD. These mutants likely occurred only sporadically in humans. Tissue-adaptations and the size of the mink relative to the infected human population size back then may have comparatively increased the relative mutation rate. Simple, multi-threaded automated docking that is widely available, assigns increased binding of the blood type II A antigen to the SARS-Cov-2 S-protein NTD of B.1.1.7 with an overall increased docking interaction of blood group A harbouring glycolipids relative to group B or H (H, p=0.04). The top scoring glycan is identified as a DSGG (also classified as sialosyl-MSGG or disialosyl-Gb5) that may compete with heparin, which is similar to heparan sulfate linked to proteinaceous receptors on the tissue surface. Other glycolipids are found to interact with lower affinity, except long ligands that have suitable ligand binding poses to match the curved binding pocket.

Predation is a driving force of organismal ecology and evolution. Predator-prey interactions, constrained by other environmental factors and historical contingency, shape physical and behavioral phenotypes of organisms on both sides of the interaction arrow. Yet despite the universality of trophic interactions in biology, study of the ecology and evolution of anti-predator defense is challenging because these interactions tend to be brief and unpredictable, and thus gathering direct evidence requires patience and serendipity. The evolution of prey defenses can be studied by DNA sequencing followed by phylogenetic analysis, and the ecology can be studied by field observation and bringing tractable systems into the lab. However, animal models generally do not allow genetic manipulation, strict control of environmental variables, or detailed observation of evolution in real time, all of which are important for demonstrating evolutionary causes and consequences. Developing complementary microbial predator-prey systems can help overcome this hurdle. There is an extensive body of work on microbial experimental evolution, and many microbes come with well-characterized genomes and established methods for genetic manipulation. As understanding of microbial ecology and the mechanisms of their trophic interactions grows apace, these systems are poised to make valuable contributions to our understanding of how predator behaviors evolve, why certain anti-predator defenses evolve and not others, and how multiple defenses function together in a single defense portfolio. These systems will enable us to both test hypotheses formulated from the study of larger organisms and to propose new ones that can be tested in larger organisms with existing methods.

Emphasizing the importance of acoustic attenuation in maintaining compliance with stringent noise regulations and enhancing workplace safety, the analysis covers the theoretical and practical aspects of sound attenuation in a turboengine testing stand. This paper presents a preliminary analysis and also an evaluation of a procedure for projecting a noise attenuator for industrial application and especially for turboengine test stands. While primarily focusing on the static acoustic behavior of the attenuator, considerations were also made regarding flow dynamics, Mach number-dependent attenuation, pressure drop, and self-generated noise aspects to provide a comprehensive perspective in selecting the optimal design configuration. The study investigates different calculation methods for assessment of the noise reduction for linear and staggered baffles, applied on a scaled reduced model of attenuator. Thus, the critical parameters and projecting requirements necessary for effective noise reduction in high-performance turboengine testing environments will be evaluated in a down-scaled model. Key factors examined include the selection of design parameters and configurations from various options. Advanced computational methods, like analytic and finite element analysis (FEM) are utilized to predict the acoustic performance and identify potential design optimizations. Experimental validation is performed to corroborate the simulation results, ensuring the reliability and efficiency of the attenuator. The findings indicate that a well-designed sound attenuator module can significantly reduce noise levels without compromising the operational performance of the turboengine inside a test cell.

Green Infrastructures (GI) are considered key to reconcile ecological and social benefits by providing multiple functions. The concept is increasingly promoted and guidelines for its implementation have been developed in many countries and regions of the Western Hemisphere. However, for other parts of the world, especially for countries with less developed infrastructures, promotion, guidance for decision-making and manuals for GI are often lacking. But the state of infrastructure development and often unplanned character of settlements in the Global South differ and result in specific constraints as well as demands to GI that need to be addressed explicitly. This study presents a methodological approach to explicitly address the specific conditions and physical limitations to GI development in urban areas of the Global South. A four step methodology was developed to assess the implementation potential for retrofitted and multifunctional urban green infrastructure in public areas. An initial site analysis (1) and the definition of design criteria as well as general strategies (2) to achieve the different dimensions of multi-functionality are the basis to derive spatial typologies (3) for GI elements and finally the spatial suitability assessment for potential placements (4). An application of the methodology to a study area in the metropolitan region of San José, Costa Rica, shows exemplarily that the potential to improve the hydrological conditions (up to 34% of surface runoff reduction), ecological conditions (increase of green space by 2,2 %, creation of 1500 m length of roadside greenery and two new habitat types), and social conditions (2.200 m of road type upgrading) of multi-functionality of the site through Green Infrastructures. These assessment results of different multi-functionality dimension can serve as a guidance for GI promotion and implementation in urban areas of the Global South.

Natural rivers in urban areas bear significant potential to provide ecosystem services for the surrounding inhabitants. However, surface sealing by houses and street networks, urban drainage, disposal of waste and wastewater resulting from advancing urbanization usually lead to the deterioration of urban rivers and their riparian areas. This ultimately damages their ability to provide ecosystem services. This paper presents an innovative methodology for a rapid and low-cost assessment of the ecological status of urban rivers and riparian areas in developing countries under data scarce conditions. The methodology uses a combination of field data and freely available high-resolution satellite images to assess three ecological status categories: river hydromorphology, water quality, and riparian land cover. The focus here is on the assessment of proxies for biophysical structures and processes representing ecological functioning that enable urban rivers and riparian areas to provide ecosystem services. These proxies represent a combination of remote sensing land cover- and field-based indicators. Finally, the three ecological status categories are combined to quantify the potential of different river sections to provide regulating ecosystem services. The development and application of the methodology is demonstrated and visualized for each 100 m section of the Pochote River in the City of León, Nicaragua. This spatially distributed information of the ecosystem service potential of individual sections of the urban river and riparian areas can serve as important information for decision making regarding the protection, future use, and city development of these areas, as well as the targeted and tailor-made development of nature-based solutions such as green infrastructure.

In the present work, an innovative range of foams, based on flax gum-filled epoxy resin was developed, reinforced or not by flax fibers. Foams and composites with different gum and epoxy resin contents were produced and characterized for mechanical and thermal performances. To enhance the organic flax gum filler's cross-linking, we exploited the oxidized components' reactivity with the amine hardener (isophorone diamine). We compared the materials obtained with those derived from the native components. Flax gum and fibers were primarily characterized by chemical analysis, NMR, and FTIR to evaluate the mild oxidation of native materials. The formation of chemical bonds between oxidized polymer chains, epoxy resin, and hardener has been evidenced by FTIR, and the materials were then studied by SEM, X-ray computed micro-tomography (CT), and submitted to mechanical and thermal tests. The relevance of oxidation treatment was highlighted, through a significant increase in density and mechanical performances (+36% and +81%, respectively for the 100% flax gum material). The positive effect of flax fibers on homogeneity evidenced through micro-CT analysis was also clearly addressed. This set of promising results paves the way for future development of fully flax-based insulation composite materials.

Twelve overnight fasted, healthy, male volunteers received on separate days a test breakfast consisting of (A) 100 g fresh white bread (providing 50 g starch) and 250 mL drinking water, (B) the same bread with a supplement of 10 g alpha-cyclodextrin dissolved in the drinking water (250 mL), and (C) 250 mL drinking water containing 25 g alpha-cyclodextrin. Capillary and venous blood samples were collected before breakfast and at regular intervals for a period of 3 hours thereafter. Plasma glucose was determined in capillary blood and plasma insulin in venous blood samples. Breakfast (A) let to the expected rise in blood glucose and insulin concentrations. Breakfast (C) did not produce a significant glycemic and insulinemic response, demonstrating that alpha-cyclodextrin is not hydrolyzed to glucose in the human digestive tract. Mild intestinal symptoms after the ingestion of alpha-cyclodextrin were reported by 4 subjects. The postprandial rises of plasma glucose and insulin were significantly smaller after breakfast (B) than (A). Under the conditions of this study, alpha-cyclodextrin reduced the glycemic and insulinemic index of white bread by 57 and 55 %, respectively. The postprandial time profile of plasma glucose and insulin suggests that, in an initial phase, the digestion of starch is inhibited by alpha-cyclodextrin almost completely. Yet, despite the delayed and reduced digestion of starch, the intake of breakfast (B) was not associated with flatulence or any other gastrointestinal symptoms.

Treatment of neurological disease is hampered by the lack of validated specific and sensitive biomarkers, resulting in delayed diagnosis and nonspecific disease modifying therapies. For example, in ALS the lack of a sensitive and specific biomarker impedes the ability to administer a treatment prior to or at the onset of motor neuron dysfunction. Although viral or other infectious etiologies have been proposed as a contributing factor to neurodegeneration, it can be argued that these are casual and not causal associations. In the case of ALS, evidence for direct causality would require in vivo validation of specific nucleotide sequences of microbial origin which are known to be neuroinvasive with tropism for motor neurons, such as polio and non-polio. Several viral enteropathogens recapitulate the pathological events in sporadic ALS, including the ability to cleave TDP-43 resulting in accumulation of misfolded proteins in the cytoplasm. This review provides supporting evidence that motor neuron disease is causally related to specific enteroviruses and argues that prospective validation is imperative for effective prevention and treatment.

Purpose of research was to determine changes in optical quality for monthly disposable soft contact lenses (SCL) wearers with new and monthly worn SCL. Retinal straylight was assessed in SCL wearers using a C-Quant straylight meter. The study included 33 participants (age 22 ± 1.4 years) who wore monthly disposable silicone hydrogel contact lenses. Measurements were taken with month-old SCL that had been worn for no more than 4 hours. Participants then replaced the old lenses with new ones. After a 15-minute adaptation period, straylight measurements were taken with the new SCL. A questionnaire was administered to all participants, inquiring about vision complaints and the type of contact lens material used. The decimal logarithm of the stray-light parameter, log(s), was notably higher with month-old SCL (log(s) = 0.97±0.17) than with brand-new SCL (log(s) = 0.86±0.15), p < 0.001. The average increase in retinal straylight after a month of SCL use was log(s) = 0.11 ± 0.08. The questionnaire revealed that 35% of participants observed a reduction in visual quality after wearing the contact lenses for a month. Results showed that monthly disposable soft contact lenses could reduce visual quality when scheduled replacement time has been reached.

Source water quality is a key determinant of drinking water quality. The recast European Union 2020/2184 drinking water directive (DWD) introduced the obligation for comprehensive risk assessment in drinking water supplies, including the water source and incorporated new elements of natural origin in the list of parameters to be monitored. The current study is the first comprehensive assessment of 15 natural elements (B, Ba, Be, Ca, Co, K, Li, Mg, Mo, Na, Se, Sr, Ti, U and V) in 1155 (82%) Hungarian drinking water sources, including surface water, bank filtered and groundwater sources. Parameters posing a risk to health (Se, V and U) were typically below the lower limit of quantification (LOQ), but higher concentrations (max. 7.0, 17 and 41 µg/L, respectively) may occur in confined locations, the latter exceeding the DWD parametric value in one water supply. Li in a small geographical area, Mg and Ca in the majority of the water supplies reached the concentration range assumed to be protective to health. Water sources were grouped in 6 clusters based on their element distribution, some of them also showing clear geographical patterns. Water types were not differentiated, with the exception of karstic waters (dominated by Ca and Mg). None of the investigated parameters are expected to be a source of public health concern.

The Cosmic Theory of Structure (CTS) model has undergone significant refinement to address the hierarchy problem by incorporating the concept of running couplings. This update provides a more robust framework for understanding the formation and evolution of cosmic structures, offering a natural explanation for mass scales due to quantum effects. We present new validations using gravitational wave data from events GW150914 and GW151226, neutrino oscillation data from IceCube, dark matter density data from the Planck survey, and quantum field interaction data. The enhanced model demonstrates improved alignment with observational data, reinforcing the CTS model's predictive power and its potential to unify gravity and quantum physics within a single theoretical framework.

Green Infrastructure promotes the use of natural functions and processes as potential solutions to reduce negative effects derived from anthropocentric interventions such as urbanization. In cities of Latin America, for example, the need for more nature-sound infrastructure is evident due to its degree of urbanization and degradation of ecosystems, as well as the alteration of the local water cycle. In this study, an experimental approach for implementation of a prototype is presented. The experiment took place in a highly urbanized watershed located in the Metropolitan Area of Costa Rica. Initially, understanding the characteristics of the study area at different scales was achieved by applying the Urban Water System Transition Framework to identify the existing level of development of the urban water infrastructure, and potential future stages. Subsequently, preferences related to spatial locations and technologies were identified from different local decision-makers. Those insights were adopted to identify a potential area for implementation of the prototype. The experiment consisted on an adaptation of the local sewer to act as a temporal reservoir to reduce the effects derived from rapid generation of stormwater runoff. Unexpected events, not considered initially in the design, are reported in this study as a means to identify necessary adaptations of the methodology. Our study shows from an experimental learning-experience that the relation between different actors advocating for such technologies influences the implementation and operation of non-conventional technologies. Furthermore, the perception of security associated to green spaces was found as a key driver to increase the willingness of residents to modify their urban environments. In consequence, those aspects should be carefully considered as factors of designs of engineering elements when they are related to complex socio-ecological urban systems.

The Doppler band compensated by the keystone transform (KT) is limited. Therefore, it needs to be used in conjunction with the Doppler ambiguity compensation function to correct the range migration (RM) caused by maneuvering targets with Doppler ambiguity. However, the KT implemented by sinc interpolation suffers from significant performance loss at boundaries of compensation Doppler bands. Additionally, in a multi-target scenario, KT implementation methods occupy high complexity when the Doppler range of targets spans over two compensation Doppler bands. To address aforementioned issues, this study presents a variable Doppler starting point keystone transform (VDSPKT) method, where a new form of ambiguity compensation function is constructed, turning the Doppler starting point of the compensation band in KT variable. Firstly, the position of the compensation Doppler band is changed from fixed to adjustable as needed, enhancing the flexibility of KT. Crucially, the connection points of the compensation Doppler bands in sinc interpolation are reset, avoiding the performance loss at their boundaries. Also, the compensation band is adjusted to cover the narrow Doppler frequency range caused by targets, significantly improving the computational efficiency. Finally, the simulation results demonstrate that the proposed approach effectively addresses the performance degradation and high computational complexity of KT in the aforementioned scenarios, resulting in a computational load reduced by approximately 50% compared to traditional methods.

During 2021 and 2022 summers, we measured the total and dissolved (&lt; 0.45 mm) concentration of 25 elements in Utah Lake using Inductively Coupled Plasma Optical Emission Spectrometry (ICP-OES). Utah regulates twelve of these elements. ICP-OES sensitivity is at the ppb-level but is not the approved regulatory method. All regulations are for dissolved concentrations; except aluminum (Al) and phosphorus (P) which are for total recovery. We found total Al concentrations above allowable, but dissolved concentrations were well below allowable concentrations. We attribute high total concentrations to suspended clays. Dissolved copper (Cu) concentrations were below regulatory levels in 2021, but some samples were above regulatory levels in 2022. This could be related to the use of Cu-based algaecide treatments, or from other sources. Lead (Pb) data were inconclusive; dissolved Pb concentrations were well below the acute (1-hour average) limit, but the chronic concentration limit (4-hour average) is below the ICP-OES minimal detection limit. Arsenic (As) concentrations exhibit a seasonal trend that we attribute to groundwater inflows. This ppb-level study provides insight into regulated elements in Utah Lake previously not available due to the high sensitivity of the method and measurements of both total and dissolved concentrations.

The prevalence of hepatitis B and delta viruses (HBV/HDV) among people who use drugs (PWUD) remains largely unknown. In the context of one Philadelphia-based harm reduction organization (HRO), this study aimed to assess HBV/HDV prevalence and facilitate linkage to care. Participants completed a demographic HBV/HDV risk factor survey and were screened for HBV and reflexively for HDV if positive for HBV surface antigen or isolated core antibody. Fisher’s exact tests and regression were used to understand relationships between risks and HBV blood markers. Of the 498 participants, 126 (25.3%) were susceptible to HBV, 52.6% had been vaccinated against HBV, and 17.9% had recovered from a past infection. Eleven (2.2%) participants tested positive for isolated HBV core antibody, 10 (2.0%) for HBV surface antigen, and one (0.2%) for HDV antibody. History of incarceration was associated with current HBV infection, while transactional sex and experience of homelessness were predictive of previous exposure. This study found high rates of current and past HBV infection, and a 10% HBV/HDV co-infection rate. Despite availability of vaccine, one quarter of participants remained vulnerable to infection. Findings demonstrate the need to improve low-threshold HBV/HDV screening, vaccination, and linkage to care among PWUD. The study also identified gaps in the HBV/HDV care cascade, including lack of point-of-care diagnostics and lack of support for HROs to provide HBV services.

Extruded polystyrene (XPS) is frequently used in the construction of many different structures. It is therefore necessary to appropriately characterize its mechanical properties to ensure the safety of said structures. Among the available characterization tests, static bending tests are simple and easy to perform; owing to these characteristics, they should be performed more frequently than other tests. However, in static bending tests on XPS, there are several challenges owing to the high flexibility of XPS, and the chosen testing method and sample configuration affect the accuracy of characterization. In this study, three bending properties (Young’s modulus, proportional limit stress, and bending strength) of samples cut from an XPS panel were determined using three-point bending (TPB), four-point bending (FPB), and compression bending (CB) tests with varying sample span/depth ratios, and statistical analyses were performed to determine the relevance of the tests. The experimental results suggest that the TPB and CB tests were more feasible than the FPB test when the span/depth ratio was appropriately determined. However, clear differences were observed in the sample bending properties determined in these tests. In light of these findings, further studies should be conducted to elucidate these differences.

We generalize the point information gain (PIG) and derived quantities, i.e., point information gain entropy (PIE) and point information gain entropy density (PIED), for the case of the Rényi entropy and simulate the behavior of PIG for typical distributions. We also use these methods for the analysis of multidimensional datasets. We demonstrate the main properties of PIE/PIED spectra for the real data on the example of several images, and discuss further possible utilizations in other fields of data processing.

In this work model of mirror elements equilibrium of the micromechanical components is developed, the behavior analysis of the mirror element of micromechanical mirrors in case changing of control voltages of electrostatic actuators is carried out, an expression for determining the maximum value of deflection voltage at which the snap-down effect will take the following form is obtained in case of the influence of the coefficient of the electrostatic rigidity of electrostatic actuators. The developed equilibrium model of mirror elements and the obtained results of modeling can be used at design of micromechanical mirrors with internal suspensions.

Panel data of our interest consist of a moderate number of panels, while the panels contain a small number of observations. An estimator of common breaks in panel means without a boundary issue for this kind of scenario is proposed. In particular, the novel estimator is able to detect a common break point even when the change happens immediately after the first time point or just before the last observation period. Another advantage of the elaborated change point estimator is that it results in the last observation in situations with no structural breaks. The consistency of the change point estimator in panel data is established. The results are illustrated through a simulation study. As a by-product of the developed estimation technique, a theoretical utilization for correlation structure estimation, hypothesis testing, and bootstrapping in panel data is demonstrated. A practical application to non-life insurance is presented as well.

In this paper, we study the global existence and exponential decay for a dynamic contact problem between a Timoshenko beam with second sound and two rigid obstacles, of which the heat flux is given by Cattaneo's law instead of the usual Fourier's law. The main difficulties arise from the irregular boundary terms, from the low regularity of the weak solution and from the weaker dissipative effects of heat conduction induced by Cattaneo's law. By considering related penalized problems, proving some a priori estimates and passing to the limit, we prove the global existence of the solutions. By considering the approximate framework, constructing some new functionals and applying the perturbed energy method, we obtain the exponential decay result for the approximate solution, and then prove the exponential decay rate to the original problem by utilizing the weak lower semicontinuity arguments.

Contact inhibition (CI) represents a crucial tumor-suppressive mechanism responsible for controlling the unbridled growth of cells, thus preventing the formation of cancerous tissues. CI can be further categorized into two distinct yet interrelated components: CI of locomotion (CIL) and CI of proliferation (CIP). These two components of CI have historically been viewed as separate processes, but emerging research indicates that they share both distinctive and common pathways. Moreover, they exhibit intriguing intersections with mechanotransduction, a process that involves cells sensing and responding to mechanical forces. This review article describes the intricate interplay between mechanical forces and CI, shedding light on how these forces regulate CIL and CIP. Emphasis is placed on filamin A (FLNA)-mediated mechanotransduction, elucidating how FLNA senses mechanical forces and translates them into crucial biochemical signals that regulate cell locomotion and proliferation. In addition to FLNA, trans-acting factors (TAFs) emerge as sensitive players in both CI and the mechanotransduction process. This article presents methods for identifying these TAFs and profiling the associated changes in chromatin structure, offering valuable insights into CI and mechanotransduction regulation. Finally, it addresses unanswered research questions in these fields and delineates their possible future directions.

Electrical contacts are important circuit components with diverse industrial applications, and their failure can lead to multiple unwanted effects. Hence, the behavior of electrical contacts is a widely studied topic in scientific literature based on various approaches, tools, and techniques. The present study proposes a numerical modeling and simulation approach based on the Holm contact theory to study the dependence between the electric potential and the temperature within an electrical contact. Structured in 5 sections, the research was conducted using COMSOL Multiphysics software and its solid-state mechanics, electric current, and heat transfer modules in order to highlight contact behavior from mechanical, electrical and thermal points of view: the von Mises stress, contact force, the electric field amplitude, the variation of the electrical potential along the current path, the temperature gradient, and dependence of temperature along the contact elements edges were obtained by simulation and graphically represented. The results are in line with the expectations and with past research that was studied in the literature review.

Since the discovery of transposable elements (TEs) in Maize in the 1940s by Barbara McClintock [1] transposable elements have been described as junk, as selfish elements with no benefit to the host, and more recently as major determinants of genome structure and genome evolution. TEs are DNA sequences that are capable of moving to new sites in the genome and make additional copies while doing so. To limit the propagation of TEs, host silencing mechanisms are directed at transposon-encoded genes that are required for mobilization. The mutagenic properties of TEs, the potential of TEs to form new genes and affect gene expression, together with the host silencing mechanisms shape eukaryotic genomes and drive genome evolution. While TEs constitute more than half of the genome in many higher eukaryotes, transposable elements in the nematode C. ele-gans form a relatively small proportion of genome, about 15% [2]. Genetic studies of transposon silencing and the discovery of RNAi in C. elegans, propelled C. elegans to the forefront of studies of RNA-based mechanisms that silence TEs. Here, I will review the transposable elements that are present and active in the C. elegans genome, and the host defense mechanisms that silence these elements.

The task of weakly supervised point cloud semantic segmentation has received widespread attention and also has been widely used in autonomous driving, robotics, and modern industries. Due to the high dimensionality and large volume of point cloud data, many technical difficulties appeal to weakly supervised semantic processing, especially segmentation. However, weakly-supervised schemes usually provide only partial labelling information of the underlying point cloud data and thus need to effectively extract local features, geometric information, and contextual relationships only using these limited labelled data for supervised learning. To improve weakly-supervised semantic segmentation, we propose a novel segmentation network through the boundary-based feature aggregation based on a K-NN algorithm with down-sampling operation, and also introduce the smoothness loss and Siamese loss for effective segmentation. The experiments on public datasets demonstrate that our presented segmentation method exceeds most of the existing fully supervised and weakly-supervised methods in terms of mIoU. Specifically, our network has high segmentation accuracy on the labels of objects with similar geometrical structures, such as ceiling, wall, floor, chair and table, reaching 91.2%, 98.8%, 83.3%, 75.3% and 80.2%, respectively. Extensive experiments also illustrate its robustness, effectiveness, and generalization of the proposed weakly supervised segmentation network.

A reliable and efficient rail track defect detection system is essential for maintaining rail track integrity and avoiding safety hazards and financial losses. Eddy current (EC) testing is a non-destructive technique that can be employed for this purpose. The trade-off between spatial resolution and lift-off should be carefully considered in practical applications to distinguish closely spaced cracks such as those caused by rolling contact fatigue (RCF). A multi-channel eddy current sensor array has been developed to detect defects on rails. Based on the sensor scanning data, defect reconstruction along the rails is achieved using an inverse algorithm that includes both direct and iterative approaches. In experimental evaluations, the EC system with the developed sensor is used to measure defects on a standard test piece of rail with a probe lift-off of 4-6 mm. The reconstruction results clearly reveal cracks at various depths and spacings on the test piece.

Air pollution has created a lot of problems in the developed and developing countries. To avoid or reduce these problems, constant monitoring of the air should be ensured. The conventional techniques is costly because it requires a lot of money and time consuming. Biomonitoring has been the alternative method. Moss, lichens and plants are biomonitors available to entrap air pollutants. The aim of this paper is to discuss one of the ways of monitoring air pollution – Moss bag technique. To do this, types, choice, preparation, handling of bags after preparation of moss were discussed. From the literatures consulted, it was discovered that there were differences in the techniques used by the researchers. In all, the use of mosses with emphasis on the employment of moss bag have proved to be a powerful tool in airborne particulate and toxic elements. To conclude, developing countries should focus more on this technique because it will reduce cost of air monitoring.

Aiming at effectively generating safe and reliable motion paths for quadruped robots, a hierar-chical path planning approach driven by dynamic 3D point cloud is proposed in this article. The developed path planning model is essentially constituted of two layers: global path planning layer and local path planning layer. At the global path planning layer, a new method is proposed for calculating terrain potential field based on point cloud height segmentation. Variable step size is employed to improve the path smoothness. At the local path planning layer, a real-time prediction method for potential collision area and a strategy for temporary target point selection is developed. Quadruped robot experiments were carried out in an outdoor complex environment. The experi-mental results verified that, for global path planning, the smoothness of the path is improved and the complexity of the passing ground is reduced. The effective step size is increased by a maxi-mum of 13.4 times, and the number of iterations is decreased by up to 1/6, compared with the traditional fixed step size planning algorithm. For local path planning, the path length is short-ened by 20%, more efficient dynamic obstacle avoidance and more stable velocity planning are achieved by using the improved dynamic window approach (DWA).

An outbreak caused by coronavirus disease 2019 (COVID-19) occurred in Wuhan City, Hubei Province, China, in December 2019. Up to March 2, 2020, at least 80180 cases have been reported. Most of the patients had a history of visiting Hubei Province or contacting with people who had ever stayed in or passed by Hubei Province, or exposed to symptoms. Some patients got infected only from asymptomatic contacts. This study aimed to report the epidemic features and lab identification of a patient confirmed with COVID-19 infection only from asymptomatic contact.

Poultry farming in Slovakia has a tradition and an irreplaceable position to ensure rational nutrition for the population. In terms of a nutritional value, poultrymeat (Galliformes) contains a high amount of proteins, essential amino acids, essential unsaturated fatty acids, minerals, vitamins and a low fat content. Poultrymeat production has a relatively short reproductive cycle and thus allows regulating the demand and supply. The poultry market also influences the development of domestic consumption. According to the Statistical Office of the Slovak Republic, the consumption of meat has witnessed a persistent increase over the last 10 years. [1] According to the 2023 AVEC (The Voice of European Meat Sector) annual report, the consumption of poultrymeat in Slovakia was 20.0 kg per person per year. The average consumption in the EU-27 (2021) was 23.4 kg, with the countries with the highest consumption being Portugal (37.8 kg), Ireland (36.0 kg), Hungary (33.5 kg) and Spain (29.9 kg). On the other hand, the countries with the lowest consumption of poultrymeat, apart from Slovakia, also include Austria and Greece with a consumption of 21.5, resp. 21.0 kg [2]. The breeding of broiler chickens, as well as the production and placing on the market of poultrymeat must comply with the requirements laid down by legislation, while the compliance is regularly checked by the competent authorities.

The Marun-Keu complex plays a significant role in understanding the geological evolution of the Ural orogen; however, it remains poorly understood. This study aims to provide insights into the complex's age, protolith composition, rock formation conditions, and its position in the region's history. The zircons from the host granitic gneisses are characterized by magmatic cores with an age of 470 Ma and metamorphic rims with an age of approximately 370 Ma. We suggest that the metamorphic rims were formed during eclogite metamorphism and that the metagranitoids hosting the eclogites experienced eclogite metamorphism simultaneously with the basic and ultrabasic rocks that are common in this area. Heterogeneous zircons were also isolated from the selvage of a pegmatite vein, in which four domains are distinguished, two to three of which can be identified within single grains, as follows: 1) igneous cores with an age of approximately 470 Ma and the geochemical characteristics of zircon crystallized in basic rocks; 2) zircons recrystallized during eclogite metamorphism with geochemical characteristics intermediate between those of the magmatic cores and true eclogitic zircon; 3) pegmatitic zircon, exhibiting the most sharply differentiated REE spectra of all four domains, characterized by a prominent positive Ce anomaly and a weakly expressed negative Eu anomaly; and 4) eclogitic zircon, observed in the form of veins and rims, superimposed in relation to the other three domains. The age of the latter three domains is within the error range and is estimated to be approximately 370 Ma. This indicates that the processes of eclogite metamorphism and the formation of pegmatites occurred at approximately the same time in the studied area.

Predictive numerical models in the study of ground-borne vibrations generated by railway sys-tems have traditionally relied on the segmented approach of subsystems. In this approach, loads are individually applied, and the cumulative effect of rolling stock is obtained through superposi-tion. While this method serves to mitigate computational costs, it may not fully capture the com-plex interactions involved in ground-borne vibrations. Recent advancements in computational and software tools have enabled the development of more sophisticated vibrational pollution models. These advanced models encompass the entire dynamic system, from the rolling stock to the terrain, allowing for continuous simulations with a defined time step. Furthermore, the incorporation of computational contact tools between various ele-ments not only ensures temporal accuracy but also extends the analysis to the frequency domain. This paper explores the evolution of predictive numerical models in the context of ground-borne vibrations generated by trains on ballasted tracks. It highlights the shift from segmented models to continuous simulations, demonstrating the progressive advancement towards more comprehen-sive and accurate representations of railway-induced and generated vibrations in the track sur-roundings as an additional way of evaluate sustainability of infrastructures. In particular, this development of a numerical model from its inception aimed to expand upon ex-isting emission - prediction models by enriching the data with frequency-domain information. This approach has been driven by the aspiration to bridge the gap between numerical predictions and measured signals, striving for a higher level of accuracy in our obtained results. This model can predict the impact of a high-speed rail (HSR) vehicle passing on its own track. It possesses sufficient information in both the time and frequency domains to precisely characterize vibrations. This initiative marks a pivotal advancement, enabling us to more effectively capture the intricacies of ground-borne vibrations and their impact on the surrounding environment due to a deeper comprehension of the occurrences in the frequency domain, there's a heightened ca-pability to accurately characterize vibrations.

Monitoring is an important component of pest management, to prevent or mitigate outbreaks of native pests, and to check for quarantine organisms. Surveys often rely on trapping, especially when the target species respond to semiochemicals. Many traps are available for this purpose, but they are bulky in most cases, which raises transportation and deployment issues, and they are expensive, which limits the size and accuracy of any network. To overpass these difficulties, entomologists have used recycled material, such as modified plastic bottles, producing cheap and reliable traps but at the cost of recurrent handywork, not necessarily possible for all end-users (e.g., for national plant protection organizations). These bottle-traps have allowed very large surveys which would have been impossible with standard commercial traps, and we illustrate this approach with a few examples. Here we present, under a Creative Commons BY-SA License, the blueprint of a fan-trap, a foldable model, laser-cut from a sheet of polypropylene, that can rapidly be produced in large numbers, and could be transported and deployed in the field with very little efforts. Our first field comparisons show that fan-traps are as efficient as bottle-traps, and we describe two cases where they are being used for monitoring.

Artificial intelligence (AI) is increasingly being used to improve the quality control of point-of-care diagnostics. This is caused by a number of factors, including the following: 1. AI can accelerate and improve testing accuracy. In comparison to humans, AI technology can review data more quickly and precisely, reducing errors and improving overall quality assurance. 2. When it comes to improving POC test findings on healthcare issues such as infectious diseases or medical crises such as heart attacks, AI can be used for sophisticated predictive analytics and modeling that aid in better decision-making. 3. Artificial intelligence facilitates process automation, increasing productivity and lowering labor costs in labor-intensive tasks such as testing and analyzing samples collected at point-of-care facilities. 4. The use of AI enables organizations implementing these solutions to gain insights from large volumes of raw diagnostic data generated faster and more accurately, allowing them to build solid frameworks around preventive care initiatives and significantly influence public health outcomes.5. Artificial intelligence (AI) has been demonstrated to be a useful tool for real-time monitoring systems that identify any problems with test results early so that they can be corrected before affected patients receive inaccurate diagnoses or treatment plans based on false information provided by diagnostic tests performed at points of care such as clinics or hospitals.Using these technologies would allow healthcare organizations to spend less on labor while still receiving exact diagnoses and rapid treatment delivery at a fraction of the cost that manual approaches required earlier.

The research of object classification and part segmentation is a hot topic in computer vision. A considerable number of studies have been carried out about deep learning on 3D point clouds. However,it is challenging to achieve effective feature learning due to sparsity of point clouds. Recently, a variety of Transformers have been adopted to improve point cloud processing and display great potential. Nevertheless, large numbers of Transformer layers tend to incur huge computational and memory costs. PointNet++ is one of the most influential neural architectures for point cloud understanding. Although the accuracy of PointNet++ has been largely surpassed by recent networks, this does not mean that PointNet++ has no potential.Thus, this paper offer two major contributions that significantly improve PointNet++ performance. Firstly, we introduce a novel contextual feature extraction (CFE) block that significantly enhances the feature extraction capabilities of PointNet++ networks. Secondly, to further enhance feature fusion, we seamlessly integrate a mutual learning (ML) block into the network architecture. By embedding these two innovative blocks within each layer of the network, we not only enrich the network's functionality but also impart it with greater robustness and adaptability. The specific experiments were conducted on the S3DIS (6-fold cross-validation) and Modelnet40 datasets with 86.5% and 92.7% accuracy, respectively, which proved that our model is comparable or even better than most existing methods for classification and segmentation tasks.

Proteins have the ability to adsorb on the surface of materials, such as soft contact lenses (SCLs), and can affect the hydrophobicity, roughness and surface properties of the contact lenses (CLs), which, in turn, can influence the friction between the lenses and the ocular surface. Excessive friction between contact lenses and the ocular surface can lead to discomfort for the wearer and may cause irritation or inflammation of the cornea, better known as corneal ulcers (keratitis). Bovine serum albumin (BSA) is often used as a standard protein in biocompatibility testing of materials, including contact lenses. One standard commercial contact lenses was tested under lubricated conditions to access the coefficient of friction (CoF), being the contact lubricated with a tear like fluid (TLF) solution containing six different concentrations of BSA. In all cases, a good linearity of the results of the friction force was verified, so the first friction law can be applied to determine the value of the coefficient of friction. It was found that friction increases with increasing protein concentration.

Analytics have become increasingly popular among sports in recent years, providing valuable information regarding physical and mental health. Many athletes have found that analytics during training can help to improve their performance, reduce the risk of injury, and enhance their overall well-being. This paper aims to improve the results of handball players by applying a method for measuring the influence of different trials on aggregate performance calculated per each athlete in order to qualify for the Olympic Games. By separating the isolated action of each trial, the result is an additional influence caused by the interaction of factors or the simultaneous action. That might explain why the neuromuscular feedback loop is utterly necessary to perform handball motor actions. Further on, the ML analysis can help identify areas for improvement, optimize training programs, and enhance overall team performance.

The principal aim of this descriptive-survey investigation is to ascertain the factors influencing individuals' choice to purchase organic commodities in Tehran. The statistical populace for this examination comprised all patrons of food retail establishments in Tehran, with the sample size determined using the Cochran formula for an unknown community size, involving the distribution of 30 questionnaires to customers (n=439). Data collection was carried out through a random sampling technique. The survey instrument consisted of a questionnaire with two sections consisting of general queries (7 questions) and specific inquiries (23 items) categorized into four dimensions (product, price, place, and promotion) for the clientele. The questionnaire's validity was confirmed through face and content validation, while its reliability was assessed utilizing Cronbach’s alpha. Data analysis was conducted using SPSS25 software, encompassing both descriptive and inferential statistical analyses. The results revealed a positive and significant correlation between customers' inclination to consume organic goods and the characteristics of the product, price, and promotion. However, no association was found between the propensity to consume organic products and location characteristics. Concerning contextual variables, a solely positive and significant correlation was identified between the willingness to purchase organic items and consumer income levels. No significant relationships were detected between other contextual variables and organic product consumption. A notable contrast was observed between respondents' gender and their readiness to buy organic products, while no significant variances were noted regarding age, income, occupation, and education in relation to the propensity to purchase organic commodities.

Contact tracing has become a vital tool for public health officials to effectively combat the spread of new diseases, such asthe novel coronavirus disease COVID-19. Contact tracing is not new to epidemiologist rather, it used manual or semi-manualapproaches that are incredibly time-consuming, costly and inefficient. It mostly relies on human memory while scalabilityis a significant challenge in tackling pandemics. The unprecedented health and socio-economic impacts led researchersand practitioners around the world to search for technology-based approaches for providing scalable and timely answers.Smartphones and associated digital technologies have the potential to provide a better approach due to their high level ofpenetration, coupled with mobility. While data-driven solutions are extremely powerful, the fear among citizens is thatinformation like location or proximity associated with other personal data and can be weaponised by the states to enforcesurveillance. Low adoption rate of such apps due to the lack of trust questioned the efficacy and demanded researchers tofind innovative solution for building digital-trust, and appropriately balancing privacy and accuracy of data. In this paper,we have critically reviewed such protocols and apps to identify the strength and weakness of each approach. Finally, wehave penned down our recommendations to make the future contact tracing mechanisms more universally inter-operable andprivacy-preserving.

In cross-country skiing the time difference between a race winner and the person coming second is typically very small. Since much of the energy is spent on overcoming resistive forces, a relatively small reduction of these can have a significant impact on the results. The resistive forces come partly from the friction in the tribological interface, between the ski and the snow, and as with many tribological applications the characterisation of its origin, plays an important role in determining the frictional properties. Also in cross-country ski friction, there are several scales impacting the frictional performance, with the major contributors being the ski-camber profile and ski-base structure. Macro-scale measurements of the ski's camber profile under load, are often used to determine how adequate the ski is for a specific condition. The characteristic properties usually obtained are, the force required to collapse the ski to a certain camber height, the topography of the kick-wax zone, and by simple means a determined lengths of the frictional interface, i.e., the apparent contact length. To this date, there are some mathematical models, but there is no robust way of determining the macro-scale contact properties between a cross-country ski and a counter surface using simulations. In the present paper an Artificial neural networks (ANN) is trained to predict the ski-camber profile for various loads placed at different positions, and a well established deterministic approach is used to simulate the contact between the ANN-predicted ski-camber profile and a linearly elastic body with a flat surface, representing the snow. The results suggest that this method is feasible for the determination of the apparent contact characteristics of different skis. Moreover, we show that the apparent contact area does not linearly depend on the load, and that the elastic properties of the counter surface also has a large impact on the apparent contact area and the average apparent contact pressure.

Although various atmospheric corrosion simulation models have been developed that give good results, industrial environments are still challenging. This paper aims to investigate the effect industrial atmospheres in Bor on the mechanical properties of structural steel S235JR and to create a constitutive model and also laboratory experimental conditions that will give the best results as an accelerated corrosion test. Atmospheric corrosion tests lasted six months, using sites close to the Electrolytic Refining Plant and Sulphuric Acid Plant, as well as air quality monitoring stations at a remote location in the city of Bor. The laboratory experiments included a salt chamber test lasting 120 h and 240 h and immersing the specimen in the electrolyte from the Electrolytic Refining Plant for 30 days. The results were compared with the standard specimens stored in the laboratory. The X-ray diffraction (XRD) method was used to identify the composition of corrosion products. The scanning electron microscopy (SEM) analysis was applied to analyze the fracture surfaces of the specimens. The use of the Complete Gurson Model (CGM) described the tensile characteristics of the corroded specimens. The study has shown that an enhanced acceleration model and conditions could be developed using numerical analysis of the test results.

For multi-sensor integrated systems, such as a mobile mapping system (MMS), data fusion at sensor-level, i.e., the 2D-3D registration between optical camera and LiDAR, is a prerequisite for higher level fusion and further applications. This paper proposes a line-based registration method for panoramic images and LiDAR point cloud collected by a MMS. We first introduce the system configuration and specification, including the coordinate systems of the MMS, the 3D LiDAR scanners, and the two panoramic camera models. We then establish the line-based transformation model for panoramic camera. Finally, the proposed registration method is evaluated for two types of camera models by visual inspection and quantitative comparison. The results demonstrate that the line-based registration method can significantly improve the alignment of the panoramic image and LiDAR datasets under either the ideal spherical or the rigorous panoramic camera model, though the latter is more reliable.

Newborn screening (NBS) is hailed as a public health success, but little is known about long-term outcomes following a positive newborn screen. There has been difficulty gathering long-term follow-up (LTFU) data consistently, reliably, and with minimal effort. Six programs developed and tested a core set of minimal LTFU data elements. After an iterative data collection process and the development of a data collection tool, the group agreed on minimal LTFU data elements. The denominator captured all infants with an NBS diagnosis, accounting for children who moved or died prior to the follow-up year. They also agreed on three LTFU outcomes: if the child was still alive, had contact with a specialist, and received appropriate care specific to their diagnosis within the year. The six programs representing NBS public health programs, clinical providers, and research programs provided data across multiple NBS disorders. In 2022, 83.8% (563/672) of the children identified by the LTFU programs were alive and living in the jurisdiction; of those, 92.0% (518/563) saw a specialist, and 87.7% (494/563) received appropriate care. The core LTFU data elements can be applied as a foundation to address the impact of early diagnosis by NBS within and across jurisdictions.

The objective of the analysis carried out in this paper is to quantify the impact of subsidies on the activity of two vegetable farms, of different sizes in terms of agricultural area under cultivation, 600 ha and 3000 ha, which can constitute a model at macroeconomic level, indicating the ways in which these farms can ensure their income. For the analysis carried out, indicators were taken into account concerning production, net profit and subsidies received over a period of three years for the agricultural crops grown on these farms, identifying their contribution and effects on profitability. Descriptive statistics, visual inspections and basic comparison methods were also used, thus determining the patterns of the impact of subsidies and their variation for each of the existing crops in the vegetable farms studied. The data on which the statistical models are based are extracted from the financial statements of the farms analysed, giving the possibility of a predictive extension of the evolution of income and, very importantly, of their profitability. The conclusions revealed, for the 600 ha vegetable farm, that this farm maintained its area constant during the analysis period, benefiting from annual subsidies, and that the practice of crop diversification (rape, barley, winter wheat, oats, soybean, maize, lucerne), appropriate rotation, conservation farming and crop irrigation on 85.34% of the area, ensured average yields/ha that exceeded those recorded at national and regional level, except for 2020. The economic performance of this farm is oscillating in the period 2018-2021, with the ability to consistently generate profit, but in 2020 it is close to break-even, a year in which subsidy income tipped the balance towards positive but modest financial results. For this farm, the statistical model carried out was inconclusive because the farm optimises its cropping plan every year, depending on agrometeorological predictions, subsidy levels and market trends, changing crops, thus not being able to estimate the extent to which each crop contributes to maintaining the financial balance of the farm. Thus, although subsidies have impacted the level of net income, the extent to which they have done so is unclear. For the 3000 ha farm, the findings revealed that this farm also has a roughly constant area in use over the analysis period and for which it receives subsidies. This farm practices crop diversification (rape, barley, winter wheat, sunflower, soybean, grain maize, late potatoes, sweet potato, carrot and flowers) and adequate crop rotation. The data highlight that subsidies played a significant and sometimes overwhelming role in determining the gross output of each crop to achieve a positive value of this indicator. Modern conservation farming technologies and crop irrigation on 74.14% of the area justify the average yields/ha achieved, which again exceeded those recorded at national, regional and county level, with the exception of 2020. Maize and soybean crops consistently contributed to the farm's income, with a high gross product and net income, despite changes in the average yield per hectare achieved each year. Good and rising economic performance for this farm during the period under review, which justifies the profitability of the business from an economic, financial and commercial point of view. Although there have been fluctuations in the value of yields realized on different crops, net revenues continued to be high and even up significantly in 2021. Thus, the study highlighted and identified trends and patterns in agriculture, patterns that can serve as a source of information for relevant policy decisions, playing a key role in guiding future research and allocating resources efficiently in the agricultural sector.

A global existential and interlocking environmental, climate and cooperation/equity polycrisis is being faced, which increasingly impacts and is impacted by water and land systems. As a result, transformations in response are gaining increasing traction. Advances in approaches to visualising and communicating how innovations and changes in landscape features enable shifts, transformations and transitions are more crucial than ever before. Visions help focus actions, collaboration and alignment of multiple actors in working towards a common purpose, whilst also entering people’s consciousness at the deep level of values, transforming beliefs and consequently, thinking and action. They give direction on effort and pull on transformational innovation. The evidence-based ‘Water Visions Visualisation Platform’ presents an innovative and accessible way to illustrate, communicate and support future water visioning and strategizing at the landscape scale based on composite paradigms, scenarios, horizons and concepts. Plausible visions of the future are envisioned, illustrated, narratively described and qualitatively assessed, as well as connected with real-world examples and resources through the interactive Platform. This paper outlines the co-creation methodology, the architecture and the co-development of the Platform, as well as a preliminary evaluation through literature-based criteria and the sharing of the Platform with a number of audiences.

The boosted interest in the use of rare earth elements (REEs) in modern technologies had also increase the necessity of their recovery from various sources, including raw materials and wastes. Though Hydrometallurgy plays a key role in these recovery processes, some drawbacks (apparent or not) of these processes, had led to the development of a more environmental friendship subclass named Solvometallurgy, in which non-aqueous solvents substituted to the aqueous media of the hydrometallurgical processing. The non-aqueous solvents chosen for these usages are, besides ionic liquids (ILs), the so-named Deep Eutectic Solvents (DEEs). The utilization of DEEs included the leaching of REEs from the different sources containing them, and also in the separation-purification steps necessary for the yielding of these elements, normally as oxides or salts, in the most purified form. This work reviewed the most recent literature (2023 year) about the utilization of deep eutectic solvents in the recovery of REEs from various sources, and in the coupling of these two (DESs and REEs) to derived compounds to be used in other fields.

The need for continuous research to refine the models used in accident reconstruction appears with the development of new car models that satisfy consumer complaints. The paper analyzed a sub-sequence of car and pedestrian accidents, from the perspective of the distance traveled by them in the contact phase, with the aim of improving the information regarding the reconstruction of road accidents. The research included the analysis of some accidents with pedestrian dummies, as well as the simulation of the impact between different classes of vehicles and pedestrians in two different walking positions. Specialized software was used with complex multibody models of pedestrians, modifying the speed and deceleration parameters at the time of the collision. The research results highlight the differences between bilinear models used in accident reconstruction and the proposed study. They can also be used to determine the distance traveled by the vehicle in the first phase of the collision with pedestrians.

Should our planet be visited by an extraterrestrial civilization, the prevailing assumption would undoubtedly be that the extraterrestrial civilization is Type I i.e. its capacity for interstellar travel results from its technological development. This assumption is dangerous for it unnecessarily leads to the Extraterrestrial Tandem Hypothesis (ETH): the belief than an extraterrestrial civilization technologically capable of interstellar travel must also be technologically compatible with the inexorably rapid annihilation of life on Earth. Such a state of things would compromise the planet’s capacity to stage a confident defense should the extraterrestrials prove belligerent. The presumption of Type I extraterrestrials (on the premise of the capacity for interstellar travel alone) is unfounded as extraterrestrials may be Type II i.e. capable of interstellar travel by virtue of natural intrinsic or extrinsic factors. This paper advances, most importantly, that the fundamental policy of first contact should be the employment of various strategies toward the evaluation of the technological capacity of visiting extraterrestrials. This evaluation must be particularly devoted to the detection of Type II extraterrestrials masquerading as Type I (using concealment and Wizard of Oz strategies). Integral to this detection are the concepts of the precedence relation and The Extraterrestrial Exclusion Principle (EEP). A precedence relation is a qualitative relation expressing the relative difficulty of producing a technological action. The Extraterrestrial Exclusion Principle states that a Type I extraterrestrial life form is excluded from certain actions. Such actions are lower in precedence than interstellar travel and may be described as in violation of the EEP or EEP forbidden. EEP actions reveal extraterrestrials to be Type II. As an example, the value of the Hawking Warning is subjected to EEP analysis. Furthermore, a hypothetical conundrum in linguistics termed the Kryptonian Linguistic Paradox (KLP) is discussed as a case of an EEP forbidden act. Finally, the paper explores the limitations of the stated fundamental policy of first contact.

Contact tracing is one of the oldest social network health interventions used to reduce the diffusion of various infectious diseases. However, some infectious diseases like COVID-19 amass at such a great scope that traditional methods of conducting contact tracing (e.g., face-to-face interviews) remain difficult to implement, pointing the need to develop reliable and valid survey approaches. The purpose of this research is to test the effectiveness of three different egocentric survey methods for extracting contact tracing data: (1) a baseline approach, (2) a retrieval cue approach, and (3) a context-based approach. A sample of 397 college students were randomized into one of each condition and were prompted to anonymously provide contacts and populated places visited from the past four days. After controlling for various demographic, social identity, psychological, and physiological variables, participants in the context-based condition were significantly more likely recall more contacts (medium effect size) and places (large effect size) than the other two conditions. Theoretically, the research supports suggestions by field theory that assume network recall can be significantly improved by activating relevant activity foci. Practically, the research contributes to developing innovative social network data collection methods for contract tracing survey instruments.

Rural landscapes are acknowledged for their potential to restore human health due to their natural characteristics. However, few studies have systematically analysed the impact of naturalness, landscape types, and combinations of landscape elements on restorativeness using both subjective and objective measurements. This study investigated the restorative effects of various rural landscapes in Guangzhou, employing electroencephalography and eye-tracking technologies to record physiological responses and using the Restorative Components Scale and the Perceived Restorativeness and Naturalness Scale to evaluate psychological responses. The results indicated the following: (1) There was a significant positive correlation between perceived naturalness and restorativeness, surpassing the impact of actual naturalness. (2) Different landscape types had a varying impact on mental health at the equal perceived naturalness. Natural forest landscapes and artificial forest landscapes exhibited the most substantial restorative effects among the natural and semi-natural landscapes examined, respectively, while settlement landscapes showed the highest restorative potential among the artificial landscapes. (3) Restorative properties varied across landscape elements, with identical elements yielding different benefits in different environments. Trees and water significantly enhanced restorativeness, whereas constructed elements such as roads and infrastructure reduced it. This study provides a scientific basis for restorative rural landscape design to enhance mental health and well-being.

Accurate classification of objects in 3D point clouds is a significant problem in several applications, such as autonomous navigation and augmented/virtual reality scenarios, which has become a research hot spot. In this paper, we presented a deep learning strategy for 3D object classification in augmented reality. The proposed approach is a combination of the GRU and LSTM. LSTM networks learn longer dependencies well, but due to the number of gates, it takes longer to train; on the other hand, GRU networks have a weaker performance than LSTM, but their training speed is much higher than GRU, which is The speed is due to its fewer gates. The proposed approach used the combination of speed and accuracy of these two networks. The proposed approach achieved an accuracy of 0.99 in the 4,499,0641 points dataset, which includes eight classes (unlabeled, man-made terrain, natural terrain, high vegetation, low vegetation, buildings, hardscape, scanning artifacts, cars). Meanwhile, the traditional machine learning approaches could achieve a maximum accuracy of 0.9489 in the best case.

The Theory of differences between elements explains the reasons for the differences in physical concepts between different elements, such as quantum physics and the Theory of general relativity, being explained through observations. Thus, it is possible to conclude from the observations that the differences are motivated by the reactions between the elements, by the composition of the elements, and by the influence of the spaces that promote losses and gains of characteristics; therefore, there is no general similarity between quantum physics and the general Theory of relativity. The study aims to understand the elements and their physical concepts that make up the Universe.

Hund's rule of maximum multiplicity is a powerful empirical tool for determining the electron population of electronic shells. It was recently discovered that it is also the rule of minimum Shannon entropy. This study extends these findings to the Aufbau rule and discusses them from the perspective of emergent dimensionality, providing a monotonically increasing entropy function. We observed that some elements that violate the Aufbau rule have the same entropies in the actual and Aufbau electron configurations. On the other hand, lower entropies of all actual elements' configurations are associated with higher or equal numbers of unpaired electrons in these configurations compared to the Aufbau configurations. The only exception to this rule is palladium.

The study aimed to evaluate for the first time the degree of contamination of soil and crops with major and trace elements (Cd, Co, Cr, Cu, Ni, Pb, Zn, F, Na, Mg, Si, P, Cl, Fe, Al) in agricultural lands situated in the Lower Danube Basin, Galati and Braila counties (SE Romania), impacted by the steel industry. Soil samples from two depths (0–5 cm and 5–30 cm), as well as leaves and seeds of wheat, corn, and sunflower, were collected from 11 different sites. Along with elemental and mineralogical analysis, performed by HR-CS AAS, PIGE, SEM-EDX and ATR-FTIR, the soil pH, texture, organic matter, electric conductivity and CaCO3 content were investigated. The results showed that the levels of Cr (83.270–383.100 mg kg-1), Cu (17.110–68.151 mg kg-1), Ni (30.157–55.656 mg kg-1), and F (319–544 mg kg-1) in soil exceeded the Romanian regulations for sensitive use of the land. The pollution indices (Igeo, EF, PI, PERI) indicate that the soil is moderate to highly contaminated with Cr, Ni and Cu, while CSI and mERMQ indices suggested a relatively low risk for metal contamination. The concentrations of elements in plant tissues and bioaccumulation factors (BFs) show the soil-plant relation and health risk, but also the elemental selectivity of vegetal compartments. Thus, the results showed that wheat plants tend to exclude the bioaccumulation of certain elements in their tissues, while for Zn and Cu, the bioaccumulation pattern is different. In the case of corn, most BFs were below 1, indicating limited phytoaccumulation capacity. However, exceptions were observed for Cd, Zn, and Cu. Sunflower BFs indicate higher bioconcentration of Cu, Cd, and Zn in both the leaves and seeds compared to other elements. Chromium (Cr) contributes to non-carcinogenic dermal contact and ingestion hazards, with children being more susceptible to the adverse effects of this contaminant.

The wave energy converter (WEC) technology constantly develops new designs and models. To encourage its development within the energy sector, research is required to improve current designs and create durable and effective devices. However, it is also crucial to investigate the suitability of a WEC to a site-specific sea condition as this can impact its optimal power absorption and constructability. This study evaluates and compares the efficiency of a heaving buoy with varied geometries in one of the most energetic places along the Mexican coast. A statistical analysis of the wave climate on the coast of Ensenada during the last 42 years is performed to define the conditions to which the device is subjected. The location of the WEC in shallow waters is chosen using a computational model which solves the modified mild slope equation in its elliptic shape. The heaving buoy floater is studied using three distinct geometries: a semi-sphere, a cylinder, and a proposed rounded semi-rectangle. The hydrodynamic response of the three geometries is then analysed in the frequency and time domain using ANSYS AQWA. The hydrodynamic study involves the assessment of the floating body dynamics, exerted forces, the power absorbed as well as the suitability of the proposed power take-off (PTO) system. Findings reveal that the proposed geometry absorbs the most energy, with an annual power of 135.11 MW, and that the transmission PTO design is appropriate for this type of technology.

The point cloud is a form of three-dimensional data that comprises various detailed features at multiple scales. Due to this characteristic and its irregularity, point cloud analysis based on deep learning is challenging. While previous works utilize the sampling-grouping operation of PointNet++ for feature description and then explore geometry by means of sophisticated feature extractors or deep networks, such operations fail to describe multi-scale features effectively. Additionally, these techniques have led to performance saturation. And it is difficult for standard MLPs to directly "mine" point cloud. To address above problems, we propose the Detail Activation (DA) module, which encodes data based on Fourier transform after sampling and grouping. We activate the channels at different frequency levels from low to high in the DA module to gradually recover finer point cloud details. As training progresses, the proposed Point-MDA can uncover local and global geometries of point cloud progressively. Our experiments show that Point-MDA achieves superior classification accuracy, outperforming PointNet++ by 3.3% and 7.9% in terms of overall accuracy on the ModelNet40 and ScanObjectNN dataset, respectively. Furthermore, it accomplishes this without employing complicated operations, while exploring the full potential of PointNet++.

A software defined radio (SDR) is a communication system that makes use of components that can be configured through software, in contrast to traditional systems where these components are variable through hardware, these radio devices are much more versatile, this article describes the factors that must be considered when implementing a communication system based on Software Defined Radios (SDR), in order to reduce the attenuation factors and thus obtain the maximum distance for a transmission of data effectively in the UHF band. The calculations made for the first Fresnel zone and for the design of the Ground Plane type antennas used in the transmission/reception stages of the x40 bladeRF platforms are also presented. The tests were carried out at the facilities of the Huarangal Nuclear Center of the Peruvian Institute of Nuclear Energy, obtaining favorable results that allow ratifying the versatility and performance of the SDRs.

Background: The risk to physicians who worked with patients without confirmed COVID-19 testing during the pandemic has been little studied. However, they were at high risk. Methods: A total of 1285 Romanian physicians completed an online survey. We performed Mann-Whitney comparisons between physicians who reported that they knowingly had direct contact with COVID patients and those who didn't regarding their willingness to work. Results: Compared with their colleagues, physicians who reported not knowingly having direct contact with COVID patients reported less access to protective equipment, less overall willingness to respond when asked to work with infected patients, more likely to work out of fear of losing their jobs, and fear of legal repercussions. They received less training in the use of protective equipment. Conclusions: Physicians who worked with patients not yet diagnosed with COVID-19 were significantly less willing to work. The perception of invisible risk may explain the observed differences.

(1) Background: Little research has been done on professionals' perceptions of institutions and governments during epidemics. We aim to create a profile of physicians who feel they can raise public health issues with relevant institutions during a pandemic. (2) Methods: A total of 1285 Romanian physicians completed an online survey as part of a larger study. We used binary logistic regression to profile physicians who felt able to raise public health issues with relevant institutions; (3) Results: Five predictors could differentiate between respondents who tended to agree with the trust statement and those who tended to disagree: feeling safe at work during the pandemic, considering the financial incentive worth the risk, receiving training on the use of protective equipment, having the same values as colleagues, and enjoying work as much as before the pandemic; (4) Conclusions: Physicians who trust the system to raise public health issues with the appropriate institutions feel they share the same values as their colleagues, say they were trained in the use of protective equipment used during the pandemic, felt they were safe at work during the pandemic, enjoyed their work as much as before the pandemic, and felt the financial bonus justified the risk.

This paper proposes a novel single-stage buck-boost three-Level neutral-point-clamped (NPC) inverter with two independent dc sources coupled for the grid-tied photovoltaic (PV) application, which can effectively solve the unbalanced operational conditions generally appeared between two coupled independent PV sources induced by the unequal irradiation and temperature distribution. The proposed control scheme can simultaneously guarantee the maximum power point (MPP) operation of both PV sources and maintain the output waveform quality. Compared to the traditional two-stage PV inverter, the proposed NPC inverter could reduce the PV array voltage requirement and dc-link capacitors’ voltage rating, meanwhile show the advantage in operational efficiency. MATLAB simulations and the captured experimental results are presented to show the performance of the proposed three-level inverter.

The theory says that the first things to exist in the universe and the current moment were driven by an imperative need; that is, the intensities of the physical concept specify influence the existence of elements and facts based on the countless observations in physical spaces in relation to elements and facts. The existence of mandatory elements in space is motivated by the characteristics of the spaces that offer conditions for such an obligation. The theory states that the universe did not arise by chance; that is, the universe emerged through determination influenced by its surroundings. The objective of the study is to help explain the elements and facts of the universe from its origins to the present.

Repetitive elements are a major component of DNA sequences due to their ability to propagate through the genome. Characterization of Metazoan repetitive profiles is picking up, however, current pipelines are failing to identify a significant proportion of divergent repeats in non-model organisms. The order Decapoda, for which repeat content analyses are largely lacking, is characterized by extremely variable genome sizes that suggest an important presence of repetitive elements. Here we developed a new standardized pipeline to annotate repetitive elements in non-model organisms, which we applied on 20 Decapoda and 6 other crustacean genomes. With our new tool we identify 10% more repetitive elements than standard pipelines. Repetitive elements were more abundant in Decapoda species than in other crustaceans, with an incredibly large number of highly repeated satDNA families. Moreover, we demonstrated a high correlation between assembly size and transposable elements and a different repeat dynamics between Dendrobranchiata and Reptantia. The patterns of repetitive elements largely reflect the phylogenetic relationships of Decapoda and the distinct evolutionary trajectories within Crustacea. In summary, our results highlight the impact of repetitive elements on genome evolution in Decapoda and the value of our novel annotation pipeline, which will provide a baseline for future comparative analyses.

Transposable elements (TEs) ubiquitously exist in the human genome, and some have the ability to copy and paste themselves to other locations, resulting in new insertions. Organisms have evolved with mechanisms and machineries to repress such activity. TEs are also co-opted for beneficial functions by the host and are thus maintained in the genome. During the lifetime of humans, aberrant TE activity might cause or contribute towards diseases including neurological conditions such as Alzheimers Disease (AD) and cancer. While inflammatory pathways linked to TEs may be a part of the disease pathology, on the other hand altered TE activity involving inflammatory pathways could be recognised by disease suppression mechanisms. For this reason, TEs could be targeted for therapeutic applications aiming to prevent TE activity or reduce initial inflammatory pathways as well as to activate disease suppression mechanisms. In this review, we describe the contributory and potential preventative roles of TEs in neurological conditions and cancer from a molecular and evolutionary perspective. Evolutionary paradigms both at the unicellular and organismal level aid understanding the role of TEs in disease. These observations could pave the way for the development of novel therapeutic approaches targeting TEs.

Interactions between mobile robots and human operators in common areas require a high safety especially in terms of trajectory planning, obstacle avoidance and mutual cooperation. In this connection the crossings of planned trajectories, their uncertainty based on model fluctuations, system noise and sensor noise,play an outstanding role. This paper discusses the calculation of expected areas of interactions du ring human-robot navigation with respect to fuzzy and noisy information. Expected crossing points of possible trajectories are nonlinearily associated with positions and orientations of robot and human. The nonlinear transformation of a noisy system input, such as directions of motion of human and robot, to a system output, the expected area of intersection of their trajectories, is done by two methods: statistical linearization and the sigma-point-transformation. For both approaches fuzzy approximations are presented and the inverse problem is discussed where the input distribution parameters are computed from given output distribution parameters.

The orbital elactronic structure of Rare Earth Elements (REEs) contains many unpaired electrons which render them capable of storing large amount of magnetic energy in addition to being critical for hitech applications. Geological deposits are their conventional sources, and the current supply chain relies on production from these deposits. However, given their critical roles in the anticipated global energy transition, there is the need to explore other viable sources to supplement current and future supplies chains. REEs occur in coal as accessory minerals and their concentration in coal ash to levels that rival those of geological deposits has been estab;ished by sophisticated analytical chemical methods. Conmventional hydrometallurgical processes rely on acid leaching, using tioxic mineral acids. Meanwhile, organosulfonic acids have pKa values that rival those of conventional minerals acid and can, therefore, be used in hydrometallurgy but their uses in this regard are not well documented in the literature. In this extensive review, we have covered geological sources of REEs exaustively in addition to showing the potential of organosulfonic acids as environmentally benign lixiviants for REEs extraction from coal ash. We have also shown how process optimization can be achieved using advance technologies while using organisulfonic acids. Moreover, we have shown current and future global market trends regarding the production of select organosulfonic acids, and the anticipated global increase in their production motivates the use of organosulfonic acids as viable lixiviants for REEs extraction from caol ash deposits.

The basis of the work of electroencephalography (EEG) is the registration of electrical impulses from the brain or some of its individual areas using a special sensor/electrode. This method is used for the treatment and diagnosis of various diseases. The use of wet electrodes in this case does not seem viable, for several well-known reasons. As a result of this, a detailed analysis of modern EEG sensors developed over the past few years is carried out, which will allow researchers to choose this type of sensor more carefully and, as a result, conduct their research more competently. Due to the absence of any standards in the production and testing of dry EEG sensors, the main moment of this manuscript is a detailed description of the necessary steps for testing a dry electrode, which will allow researchers to maximize the potential of the sensor in the various type of research.

COVID-19 is frequently associated with a coagulopathy with severe consequences. The mechanisms leading to a pro-coagulant state in these patients is multifactorial, including tissue destruction and inflammatory mechanisms. Based on the analysis of publicly available interactomes, we propose that SARS-CoV-2 infection causes a deficiency in C1 esterase inhibitor (C1-INH), a pathogen-specific mechanism that may help explain the pro-coagulant state in COVID-19 patients.

It is argued that all physical knowledge ultimately stems from observation and that the simplest possible observation is that an event has happened at a certain space-time location . Considering historic experiments, which had been groundbreaking in the evolution of our modern ideas of matter on the atomic, nuclear and elementary particle scales, it is shown that such experiments produce as outputs macroscopically observable events which represent binary decisions with regard to simple alternatives and which accumulate in the course of time into spatio-temporal patterns whose forms allow decisions to be taken concerning conceivable alternatives of explanation. Working towards elucidating the physical and information-theoretic characteristics of those elementary pieces of information we arrive at the conclusion that - unlike the events of relativity which are mere 4-tuples of spacetime coordinates - the events of observation are pieces of information endowed with the properties of physical action, spacetime extension, and Lorentz invariance. Another important aspect is that such events are produced at the expense of irreversibly dissipating energy which can be stated in Landauer diction in the form that more energy needs to be spent in the erasure of events than had previously been invested in their initiation.

We introduce a new generalized inverse (i.e., generalized EP element) which is a natural generalization of EP and *-DMP elements in a Banach *-algebra. We present polar-like characterizations of generalized EP elements. The necessary and sufficient conditions under which the sum of two generalized EP elements is a generalized EP element are investigated. Finally, the generalized core-EP orders for generalized EP elements are characterized.

The modeling of tilting-pad journal and thrust bearings presents a level of complexity beyond that of bearings of fixed-arc geometry, particularly with regard to dynamic influences. With tilting-pad bearings, the theory surrounding the fluid film must be complemented with representative modeling of the pad dynamics. What has been recognized in recent decades has been the significance of the pad support, in particular the flexibility of the pivot region of the pad. The typical model for including the stiffness of the pivot has been based on Hertzian contact theory. Some researchers have been noting that the Hertzian theory does not permit sufficient flexibility in the pivot region. It is suggested that the contact mechanics at the pivot would be better represented as a pairing of rough surfaces. The modeling used here is based on a statistical asperity micro-contact theory for rough-surface line contact that has been extended to include contact stiffness. This model has been applied to the determination of the effective dynamic properties of tilting-pad bearings. The results show that pivot stiffness can be as low as one-third the stiffness determined by Hertzian theory. Comparison to published experimental results confirms the significance of the rough-surface modeling, particularly for the line contacts associated with rocker-back tilting pads.

Concrete condition assessing penetrometers need to be able to distinguish between making contact with a hard (concrete) surface as opposed to a semi-solid (corroded concrete) surface. If a hard surface is mistaken for a soft surface, concrete corrosion may be over-estimated, with the potential for triggering unnecessary remediation works. Unfortunately, the variably-angled surface of a concrete pipe can cause the tip of a force-sensing tactile penetrometer to slip and thus to make this mistake. We investigated whether different shaped tips of a cylindrical penetrometer were better than others at maintaining contact with concrete and not slipping. We designed a range of simple symmetric tip shapes, controlled by a single superellipse parameter. We performed a finite element analysis of these parametric models in SolidWorks before machining in stainless steel. We tested our penetrometer tips on a concrete paver cut to four angles at 20∘ increments. The results indicate that penetrometers with a squircle-shaped steel tip (a=b=1,n=4) have the least slip, in the context of concrete condition assessment.

This paper proposes a contact force controller for a constrained flexible manipulator in three-dimensional motion. This controller used the conversion formula obtained empirically and experimental results showed the effectiveness of the proposed contact force controller. First, the manipulator was operated with the tip of the second link restrained, then, time response of the root strain, joint angles and contact force were used to derive the relational between the three quantities. The effectiveness of the relational expression was verified by conducting a target contact force tracking experiment by inputting the angle from the relational expression. The contact force control using the strain feedback method was proposed with the strain amount estimated from the target contact force as the target value, and its effectiveness was verified by experiments. From the results obtained, controller using the strain feedback method was designed for the purpose of controlling the contact force at the tip of a flexible manipulator with two links and three degrees of freedom that performs three-dimensional spatial motion, and its effectiveness was shown by comparison with the contact force feedback method.

The accurate calculation of real contact area between rough surfaces is a key issue in tribology. In this paper, based on the geometrical information of total contact area and the number of contact spots with respect to surface separation, a new method is proposed to determine the relation between real contact area and normal load. The contact of rough surfaces is treated as an accumulation of incremental multi-plateaus indentations with varying average contact radius. Comparisons with direct finite element calculations and some other theoretical predictions demonstrate the efficiency of this approach.

Total hip arthroplasty is a complex procedure. The achievements of implantology enabled the development of a faithful representation of hip joint physiology as well as the production of materials that can successfully replace damaged natural tissues. A very important issue is the correct selection of the geometry of the endoprosthesis adequate to the load of the joint. Materials used for endoprosthesis are a metal head and a polymer cup (e.g. PE-UHMW). The main interactions in the endoprosthesis are friction and surface pressure, which must be limited, exceeding them causes the destruction of the biomechanical system - plastic deformation of the polymer and the formation of too large and unacceptable radial clearances. Based on the author's developed calculation method of hip joint endoprosthesis contact parameters, the impact on maximum contact pressure and the angle of contact of the joint load was estimated depending on the diameter of the endoprosthesis and radial clearance. The correctness of changing the values of maximum contact pressure from the mentioned parameters was determined. Correspondingly: an increase in joint load causes a linear increase in the maximum contact pressure; increasing the diameter of the endoprosthesis head - their non-linear decrease, and increasing radial clearance - their increase

In this paper we analyse spatial variation in Japanese dialectal lexicon by assembling a set of methodologies using theories in variationist linguistics and GIScience, and tools used in historical GIS. Based on historical dialect atlas data, we calculate a linguistic distance matrix across survey localities. The linguistic variation expressed through this distance is contrasted with several measurements, based on spatial distance, utilised to estimate language contact potential across Japan, historically and at present. Further, administrative boundaries are tested for their separation effect. Measuring aggregate association within linguistic variation can contrast previous notions of dialect area formation by detecting continua. Depending on local geographies in spatial subsets, great circle distance, travel distance and travel times explain a similar proportion of the variance in linguistic distance despite the limitations of the latter two. While they explain the majority, two further measurements estimating contact have lower explanatory power: least cost paths modelling contact before the industrial revolution, based on DEM and seafaring, and a linguistic influence index based on settlement hierarchy. Historical domain boundaries and present day prefecture boundaries are found to have a statistically significant effect on dialectal variation. However, the interplay of boundaries and distance is yet to be identified. We claim that a similar methodology can address spatial variation in other digital humanities, given a similar spatial and attribute granularity.

An investigation was made to determine the effects of tungsten surface coating on the coefficient of friction of sliding contact between lubricated steel surfaces. The four-ball test was modified, using a tungsten carbide ball bearing in the spindle to cause sliding contact onto three hard steel ball bearings coated with tungsten disulfide lamellar dry lubricant coating, with a coating of grease lubrication applied to the ball bearings. The coatings, loads, speed, and grease level was varied to best understand the impact of different conditions to the friction coefficient.

Togo is one of the countries characterized by the highest deforestation rate in the world, caused mainly by the overexploitation of domestic biomass energy. Uapaca togoensis being one of the species appreciated for its strong calorific power, is increasingly overexploited, and its rarefaction in the Togolese forest landscapes becomes worrying hence the need to conduct this study to evaluate the possibilities of its vegetative reproduction. This study contributes to the sustainable development of natural resources by determining the optimal conditions for assisted regeneration of Uapaca togoensis. The approach consisted in conducting a series of nursery trials to determine the impact of the substrate, size of cuttings, sunlight, and apical tip coverage of the plastic film on its germination and budburst capacity. The lower calorific value is determined from samples in dry wood slices of 350g to 500g in five diameter classes. After 33 days, only one unscarred seed germinated in the compost. Substrate type, diameter of cuttings, sunlight, and plastic film significantly influenced the budburst rate and delay. More than 70% of the medium-diameter segments budded compared to 60% and 50% for small and large-diameter segments. More than 80% of the segments exposed to sunlight budded compared to 60% for the shaded segments. The average lower calorific value of dry wood of Uapaca togoensis varies between 7.35 Mj/Kg and 12.12 Mj/Kg depending on the humidity rate and the diameter.

The authors have revised the circularity of materials, which is important to stimulate circular activity processes. The theoretical part starts with describing the characteristics of the circular activity and the comparison of circular and linear systems in terms of recycling. Later on, the authors examined key elements important for the circularity and the results of an examination of various sectors. The authors formed a correlation matrix and used a dynamic regression model to identify the circular material use rate. The authors suggested a three-level methodology, using it provided a dynamic regression model which could be applied for forecasting the size of circular material use rate in European Union countries. The results show that private investments into recycling and the recycling of electronic waste and the recycling of other municipal waste categories are important in seeking to increase the usage rate of circular materials.

Online social networking techniques and large-scale multimedia retrieval are developing rapidly, which not only has brought great convenience to our daily life, but generated, collected, and stored large-scale multimedia data as well. This trend has put forward higher requirements and greater challenges on massive multimedia retrieval. In this paper, we investigate the problem of image similarity measurement, which is one of the key problems of multimedia retrieval. Firstly, the definition of similarity measurement of images and the related notions are proposed. Then, an efficient similarity measurement framework is proposed. Besides, we present a novel basic method of similarity measurement named SMIN. To improve the performance of similarity measurement, we carefully design a novel indexing structure called SMI Temp Index (SMII for short). Moreover, we establish an index of potential similar visual words off-line to solve to problem that the index cannot be reused. Experimental evaluations on two real image datasets demonstrate that the proposed approach outperforms state-of-the-arts.

Techniques for the controlled seeding and growth of cracks are urgently required for non-destructive testing technique evaluation, particularly for additive manufactured (AM) samples. This paper describes a method which uses a combination of tensile load and resonance excitation of notched AM samples, with in-situ monitoring of the resonance frequency serving to track crack dimensions. Mechanical low-cycle fatigue cracks, ranging in length from ~0.3 mm to ~5 mm, are successfully created in five AM samples using this technique. The samples are non-destructively characterized using optical microscopy and Nonlinear Resonance (NLR) testing. The exploitation of resonance enables the concentration of a significant number of stress cycles on the samples in much shorter timespans than conventional fatigue testing, enabling high throughput, while utilising compact components. Furthermore, the tracking of resonance frequency shift throughout the process enables non-invasive and non-contact real-time condition monitoring.

In this paper, we present a method to map information regarding service activity provision residing in governmental portals across European Commission. In order to perform this, we used as a basis the enriched Greek e-GIF ontology, modeling concepts, and relations in one of the two data portals (i.e., Points of Single Contacts) examined, since relevant information on the second was not provided. Mapping consisted in transforming information appearing in governmental portals in RDF format (i.e., as Linked data), in order to be easily exchangeable. Mapping proved a tedious task, since description on how information is modeled in the second Point of Single Contact is not provided and must be extracted in a manual manner.

Different contact materials along with optimization of the deposition techniques expand the possibilities to obtain high performance room temperature CdTe-based X/γ-ray detectors. The heterostructures with ohmic (MoOx) and Schottky (MoOx, TiOx, TiN, and In) contacts, created by DC reactive magnetron sputtering and vacuum thermal evaporation, as well as In/CdTe/Au diodes with a p-n junction, formed by laser-induced doping, were developed and investigated. Depending on the pre-treatment of the surface of semi-insulating p-CdTe crystals, deposition of a MoOx film formed an ohmic or Schottky contact. Based on the calculations and IV characteristics of the fabricated Mo-MoOx/р-CdTe/MoOx-Mo, In/CdTe/MoOx-Mo, Ti-TiOx/р-CdTe/MoOx-Mo, and Ti-TiN/р-CdTe/MoOx-Mo Schottky-diode detectors, the current transport processes were described in the models of the carrier generation-recombination within the space-charge region (SCR) at low bias voltages, and space-charge limited current at higher voltages, respectively. The energies of generation–recombination centers, density of trapping centers, and carrier lifetimes were determined. A sharp increase in the reverse current in the Mo-MoOx/р-CdTe/MoOx-Mo, Ti-TiOx/р-CdTe/MoOx-Mo, and Ti-TiN/р-CdTe/MoOx-Mo heterostructures at high bias was discussed in frames of the Poole–Frenkel emission model. Nanosecond laser irradiation of the In electrode, pre-deposited on the p-CdTe crystals, resulted in an increase in the voltage range, corresponding to the carrier generation-recombination in the SCR, in the IV characteristics of the In/CdTe/Au diodes. Such In/CdTe/Au p-n junction diodes demonstrated high energy resolutions (7%@59.5 keV, 4%@122 keV, and 1.6%@662 keV).

The function of the endoplasmic reticulum (ER) can be impaired by the alternation of the extra- and intracellular environment such as disruption of calcium homeostasis, expression of mutated proteins and oxidative stress. In response to disruptions to ER homeostasis, eukaryotic cells activate canonical branches of signal transduction cascades, collectively termed the unfolded protein response (UPR). The UPR attempts to recover the protein folding capacity and avoid irreversible cellular damage. Additionally, the UPR has been shown to play unique physiological roles in the regulation of diverse cellular events, including cell differentiation and development and lipid biosynthesis. Recent studies have indicated that these important cellular events are also regulated by contact and communication among organelles. These reports suggest strong involvement among the UPR, organelle communication and regulation of cellular homeostasis. However, the precise mechanisms for the formation of contact sites and the regulation of its dynamics by UPR remain unresolved. In this review, we summarized the current understanding of how the UPR regulates morphological changes to the ER and the formation of contact sites between the ER and other organelles. We also review how UPR-dependent connections between the ER and other organelles affect cellular and physiological functions.

The function of the endoplasmic reticulum (ER) can be impaired by the alternation of the extra- and intracellular environment such as disruption of calcium homeostasis, expression of mutated proteins and oxidative stress. In response to disruptions to ER homeostasis, eukaryotic cells activate canonical branches of signal transduction cascades, collectively termed the unfolded protein response (UPR). The UPR attempts to recover the protein folding capacity and avoid irreversible cellular damage. Additionally, the UPR has been shown to play unique physiological roles in the regulation of diverse cellular events, including cell differentiation and development and lipid biosynthesis. Recent studies have indicated that these important cellular events are also regulated by contact and communication among organelles. These reports suggest strong involvement among the UPR, organelle communication and regulation of cellular homeostasis. However, the precise mechanisms for the formation of contact sites and the regulation of its dynamics by UPR remain unresolved. In this review, we summarized the current understanding of how the UPR regulates morphological changes to the ER and the formation of contact sites between the ER and other organelles. We also review how UPR-dependent connections between the ER and other organelles affect cellular and physiological functions.

We investigate the impact of aging on exchangeable inter-arrival times in mixed renewal processes, exploring its implications for reliability and survival analysis. In this study, first, we revisit the definition of renewal point processes, where inter-event time intervals are considered as exchangeable non-negative random variables. Then, we define the concept of statistical aging as latency in the observational process of event counting. Latency affects event detection but preserves exchangeability. However, it may alter the statistical properties of inter-event time intervals. Our analytical and numerical assessments highlight the significance of aging in exchangeable lifetimes, offering insights into key metrics such as the failure survival function, renewal function, and hazard rate function. Through archetypal examples and empirical findings, we illustrate the implications of aging on renewal processes. In particular, employing a Bayesian perspective, we analyze high-frequency currency exchange rate data to assess the impact of aging on volatility risk evaluation. This study contributes novel insights to the literature of renewal theory and survival analysis, emphasizing the role of latency aging in stochastic point processes under exchangeability assumption.

We consider a Cauchy problem for differential equations in a Hilbert space $X$. The problem is stated in a time interval $I$, which can be finite or infinite. Weuse a fixed point argument for history-dependent operators to prove the unique solvability of the problem. Then, we state and prove convergence criteria for both a general fixed point problem and thecorresponding Cauchy problem. These criteria provide necessary and sufficient conditions on a sequence $\{u_n\}$ which guarantee its convergence to the solution of the corresponding problem, in the space of both continuous and continuously differentiable functions. We then specify our results in the study of a particular differential equation governed by two nonlinear operators. Finally, we provide an application in viscoelasticity and give a mechanical interpretation of the corresponding convergence result.

First came the digital banks without offices, and then the “fintech” companies that combined technology and finance to achieve greater efficiency and new business models. Later was the turn of transport and logistics, understood as the sector whose economic activities derived from the transport of people and goods, while on the one hand, it has had a new spring thanks to factors such as online sales. Then, perhaps catalyzed by the pandemic scenario, the turn has reached education, where years ago was only a complement of traditional education, now is a central part with multiple modern methodologies. Numerous studies exist about using or implementing these e-learning procedures, but technical analysis is barely found in references. This work aims to analyze the digital transformation of the main sectors of our society, including finances, transport, and education, together with several examples of how technology was helping to fight the pandemic scenario.

Currently, there is increasing industrial demand for rare earth elements (REE) as these elements are now integral to the manufacture of many carbon-neutral technologies. The depleting REE ores and increasing mining costs are prompting to look for alternative sources for these valuable metals, particularly from waste streams. Although REE concentrations in most of the alternate resources are lower than current REE ores, some sources such as marine sediments, coal ash, and industrial wastes like red mud are looking promising with significant concentrations of REE in them. This review focuses on the alternative resources for REE such as ocean bottom sediments, continental shelf sediments, river sediments, stream sediments, lake sediments, phosphorites deposits, industrial waste products like red mud, and phosphogypsum, coal, coal fly ash, and related materials, waste rock sources from old and closed mines, acid mine drainage, and recycling of e-waste. Possible future Moon exploration and mining for REE and other valuable minerals are also discussed. It is evident that REE extractions from both primary and secondary ores alone are not adequate to meet the current demand, and sustainable REE recovery from the alternative resources described here is also necessary to meet the growing REE demand. An attempt is made to identify the potential of these alternative resources and sustainability challenges, benefits, and possible environmental hazards to meet the growing challenges in meeting the future REE requirements.

Façade elements are a building component that satisfies multiple performance parameters. Among other things, “advanced façades” take advantage of hybrid solutions, such as assembling laminated materials. In addition to the enhanced mechanical properties that are typical of optimally composed hybrid structural components, these systems are energy-efficient, durable, and offer lighting comfort and optimal thermal performance, an example of which is the structural solution developed in collaboration with the University of Zagreb and the University of Ljubljana within the Croatian Science Foundation VETROLIGNUM project. The design concept involves the mechanical interaction of timber and glass load-bearing members without sealing or bonding the glass-to-timber surfaces. Following earlier research efforts devoted to the structural analysis and optimization of thus-assembled hybrid Cross-Laminated Timber (CLT)-glass façade elements, in this paper, special focus is given to a thermal and energy performance investigation under ordinary operational conditions. A simplified numerical model representative of a full-size building is first presented by taking advantage of continuous ambient records from a Live-Lab mock-up facility in Zagreb. Afterwards, a more detailed Finite Element (FE) numerical analysis is carried out at the component level to further explore the potential of CLT–glass façade elements. The collected numerical results show that CLT–glass composite panels can offer stable and promising thermal performance for façades similar to national and European standard requirements.

The extensive use of rare earth elements (REEs) in a number of technologies is expected to impact on human health, including occupational REE exposures. A body of experimental evidence on REE-associated toxicity has been accumulated in recent decades. Unlike experimental studies, the consequences of REE exposures to human health have been subjected to relatively fewer investigations. Geographical studies have been conducted on residents in the Chinese REE mining districts, reporting on REE bioaccumulation, and associations between REE residential exposures and adverse health effects. A more limited series of studies has been focused on occupational REE exposures, such as movie operator (with occurrence of cerium aerosol) with the observation of pneumoconiosis and lung fibrosis. Similar effects have been reported in case reports for other workers, such as a lens grinder and a printer exposed to carbon-arc lamp emission. As for the occupations related to REE mining and processing, REE bioaccumulation in scalp hair and excess REE urine levels were reported. A study was devoted to workers employed in e-waste separation, showing alterations of several plasma markers. As for other REE occupational exposures, mention should be made of: a) mechanical workshops, with exposures to diesel exhaust microparticulate (containing nanoCeO₂ as a catalytic additive) and, b) production and manufacture of REE supermagnets for hybrid engines and wind turbines. Diesel exhaust microparticulate has been studied in animal models, leading to evidence of several pathological effects in animals exposed by respiratory or systemic routes. As for supermagnet production and manufacture, a body of literature is reviewed of experimental studies, and of human exposure studies showing several pathological effects of static magnetic fields, warranting further investigations.

Background: Since March 2020, Spain is severely hit by the ongoing pandemic of coronavirus disease 19 (COVID-19) caused by severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2). Understanding and disrupting the early transmission dynamics of the infection is crucial for impeding sustained transmission. Methods: We recorded all COVID-19 cases and traced their contacts in an isolated rural community. We also sampled 10 households, 6 public service sites and the wastewater from the village sewage for environmental SARS-CoV-2 RNA. Results: The first village patient diagnosed with COVID-19-compatible symptoms occurred on March 3, 2020, twelve days before lockdown. A peak of 39 cases occurred on March 30. By May 15, the accumulated number of symptomatic cases was 53 (6% of the population), of which only 22 (41%) had been tested and confirmed by RT-PCR as SARS-CoV-2 infected, including 16 hospitalized patients. Contacts (n=144) were six times more likely to develop symptoms. Environmental sampling detected SARS-CoV-2 RNA in two households with known active cases and in two public service sites: the petrol station and the pharmacy. Samples from other sites and the wastewater tested negative. Conclusions: The low proportion of patients tested by RT-PCR calls for urgent changes in disease management. We propose that early testing of all cases and their close contacts would reduce infection spread, reducing the disease burden and fatalities. In a context of restricted testing, environmental RNA surveillance might prove useful for early warning and to identify high-risk settings enabling a targeted resource deployment.

Despite the existence of pasteurization and its advocacy worldwide, most marketed milk in a developing country like Nigeria are sold raw by the locals. It costs hundreds of millions of Naira to set up a conventional pasteurizing plant in Nigeria. Boiled milk ends up curdling which results in to a loss of nutrients, so it is not beneficial to treat milk by this method. This paper hence presents the re-designing and fabrication of the contact area of a solar milk pasteurizer

This study investigated how different gamification elements in mobile apps influence users' basic psychological needs (autonomy, competence, relatedness) and subsequent engagement outcomes. Survey data was analyzed using PLS-SEM. Social gamification elements enhanced autonomy and competence needs, while immersive elements boosted autonomy and relatedness. Achievement/progression components increased competence and relatedness perceptions. Interestingly, personal traits did not significantly impact psychological needs. Crucially, satisfying autonomy and relatedness predicted higher user satisfaction and continued usage intentions, highlighting their importance for sustained engagement. Competence influenced satisfaction but not continuance intention. The findings demonstrate the motivational roles of distinct gamification features in fostering need-supportive experiences. Designers should incorporate varied social, immersive, and achievement components to address users' psychological requirements holistically. Prioritizing autonomy and relatedness support appears vital for achieving enjoyable, self-motivated, and persistent user engagement across gamified systems and domains. The study provides actionable insights for optimizing motivational affordances through psychologically-informed gamification implementations.

Lymphedema is a chronic and debilitating disease that affects up to 250 million patients worldwide. Recent advances in understanding its pathophysiology, along with improved diagnosis and microsurgical techniques, have enhanced our ability to cope with the challenging task of treating this disease. This review provides an overview of the disease from a surgeon's point of view, including existing imaging modalities used for preoperative assessment, as well as surgical procedures used in its treatment. Advantages and drawbacks of various existing modalities used for pre or intraoperative assessment of lymphatic vessels are discussed. Lymphedema treatment has shifted from palliative debulking procedures (liposuction and direct excision) to those aimed at restoring lymphatic flow and countering the pathophysiology of the disease (lymphaticovenous anastomosis and vascularized lymph node transfer). A combination of both approaches can result in a synergistic benefit for patients and are discussed in this review. Despite recent advances, some controversies persist, and further studies are needed to better define surgical treatment algorithms.

The South of France is a biodiversity hotspot within Europe. Here, we present a comprehensive review of surveys conducted in the Cent Fonts aquifer, an overlooked subterranean biodiversity hotspot embedded in a region rich in stygobiotic species and threatened by climate change and water abstraction projects. Key studies, spanning from 1950 to 2006, show a progression in survey methods and results, although troglobiotic species remain poorly documented. With 43 stygobiotic species recorded, the Cent Fonts is the second richest stygobiont hotspot in Europe. Most species are regional endemics, a quarter of which are considered vulnerable by the IUCN. The Cent Fonts also hosts several relict species and is the type locality of four species. Such a high biological value clearly deserves to be preserved. Our analysis warns of a possible decline in biodiversity, as 8 of the species recorded in the 20th century were absent from the 2006 survey, suggesting potential threats of unknown origin. The capture of the Cent Font springs for water abstraction is discussed as a potential threat to this ecosystem and its unique biodiversity. Three new species of stygobiotic molluscs are described, one of which was collected in the Cent Fonts.

Hair cosmetics are in fashion. Numerous products are commonly used in combination. Frequent allergens are present in hair cosmetics, which, added to almost daily use, increase the risk of sensitization. Familiarity with the clinical distribution of the eczematous rash is necessary to seriously consider patch testing. There are haptens on the market, although not all of them. It is necessary to know how to patch your own products. When avoidance of the allergen cannot be possible, new treatments are being evaluated to combat allergic contact dermatitis, mainly of the occupational type. In this manuscript, a complete and practical review of the main allergens and contact sources of hair cosmetic origin has been carried out.

Keratoconus is a condition that causes progressive thinning and anterior protrusion of the cornea. Because of its irregular astigmatism, mild to moderate keratoconus is corrected with hard contact lenses (HCL), but blepharoptosis due to long-term wear is often a problem. In this study, we investigated blepharoptosis in hard contact lens wearers with keratoconus. Thirty seven keratoconic eyes were enrolled and divided into several groups according to their wearing history or age. Eyelid margin distance (EMD), margin light reflex distance-1 (MRD-1) and eyelid elevator muscle function were measured by ruler or anterior segment optical coherence tomography. EMD decreased with years of HCL wear but showed no correlation with age; MRD-1 decreased with years of wear and with older age; LF showed no relationship with either years of wear or age. In the classification of ptosis, there was no severe ptosis in the present sample. Long-term wear of HCLs is likely to cause blepharoptosis even in keratoconic eyes, but its degree may be mild.

Cycloid drives are generally used in precision machinery requiring high reduction ratios, such as robot joint (RV) reducers, in which the contact load and stress property of the internal meshing pairs greatly affect the dynamic transmission performance of the reducers. Therefore, in this study, Isogeometric Analysis (IGA) was employed to explore the multi-tooth contact problem of the cycloid pinwheel drive. Based on the NURBS curved surface generation method, the NURBS tooth profile of the cycloid gear was reconstructed. In addition, the NURBS surface of the cycloid gear - pin tooth - output pin was generated via the element splicing method. A geometrical analysis model of cycloid pinwheel drive was established to solve the contact force of the meshing pair under different input angles, and compared with the finite element method in terms of convergence, resultant accuracy, and solving timeliness. The results show that the Isogeometric analysis has higher accuracy and efficiency than the finite element method in calculating the contact stress and contact force. This method can improve the contact simulation accuracy of the cycloid drive and provides a reference for the design evaluation of RV reducer.