Non-isocyanate polyurethane synthesis by non-Sn catalysis is an essential challenge toward green polyurethane synthesis. Bismuth compounds are attractive candidates due to their low cost, low toxicity, and availability to urethane chemistry. We applied various Bi catalysts to the self-polycondensation of a bishydroxyurethane monomer and found BiCl3 to be an excellent catalyst through optimization. The catalytic activity and price of BiCl3 are comparable to those of Bu2SnO, while its toxicity is significantly low. BiCl3 is, therefore, a promising alternative to Sn-based catalysts in non-isocyanate polyurethane synthesis.

The review scrutinizes the currently performed research on the new methods for enhancing bituminous binder performance through radiation and radical grafting of polymer modifers of bitumen. It investigates innovative methods, including using waste polymers as modifiers, and applying radiation for polymer grafting, to overcome challenges like high costs, low aging resistance and storage stability issues, of which separation of phases polymer/bitumen is the most significant obstacle. These advanced modification techniques promise sustainability through the decrease of the carbon footprint of transportation systems by improving the properties and durability of binders. Additionally, the review discusses the parameters and mechanistic aspects from a scientific perspective, shedding light on the underlying processes that contribute to the improved performance of modified bituminous binders.

The one-dimensional MoS₂/carbon nanofibers (1D MoS₂/CNFs) are synthesized by electrospinning using exfoliated MoS₂ nanosheets and polyacrylonitrile as raw materials. The exfoliated MoS₂ nanosheets with size of about 150 nm are encapsulated in carbon nanofibers, and the free-standing MoS₂/CNFs can be easily cut into flexible tablet and directly used as binder-free anode for lithium storage. The resultant 1D MoS₂/CNFs exhibit a very high reversible capacity of 700 mAh g^-1 at 100 mA g^-1 after 50 cycles, high rate capacity (450 mAh g^-1 at 1000 mA g^-1 after 200 cycles) and good cycle stability.

To better understand the shape memory materials and self-healing materials, a new series of liquid-crystalline shape memory polyurethane (LC-SMPU) composites, named SMPU-OOBAm, were successfully prepared by incorporating 4-octyldecyloxybenzoic acid (OOBA) into the PEG-based SMPU. The effect of OOBA on the structure, morphology and properties has been carefully investigated. The results demonstrate that SMPU-OOBAm have liquid crystalline properties, triple-shape memory properties and self-healing properties. The incorporated OOBA promotes the crystallizability of both soft and hard segments of SMPU, and the crystallization rate of the hard segment of SMPU decreases when the OOBA-content increases. Additionally, the SMPU-OOBAm forms a two-phase separated structure (SMPU phase and OOBA phase), and it shows two-step modulus changes upon heating. Therefore, the SMPU-OOBAm shows triple-shape memory behavior, and the shape recovery ratio decreases with an increase in the OOBA content. Finally, SMPU-OOBAm shows self-healing properties. The new mechanism can be ascribed to the heating-induced “bleeding” of OOBA in the liquid crystalline state and the subsequent re-crystallization upon cooling. This successful combination of liquid crystalline properties, triple-shape memory properties and self-healing properties make the SMPU-OOBAm composites with many promise applications in smart optical devices, smart electronic devices and smart sensors.

The aim of this study was to evaluate the effect of two different insertion speeds at 8 different insertion torque values ranging from 25-60 during implantation in a dense polyurethane D1 bone model on the placement status and removal torque of dental implants. In this study, 50 pcf single layer polyurethane plates were used. In the study, a total of 320 implant sockets were divided into 2 groups as Group 1 (30 rpm) and Group 2 (50 rpm) in terms of insertion speed. Group 1 and Group 2 were divided into 8 subgroups as 25, 30, 35, 40, 45, 50, 55 and 60 torques. There were 20 implant sockets in each subgroup. During the implantations, implant placement status and removal torque values were assessed. There was a statistically significant difference between the 30 and 50 RPM groups in terms of overall implant placement status (p<0.01). It was found that the removal torque values at 50 RPM were statistically significantly higher than those at 30 RPM (p<0.01). This study showed that in dense D1 bone, the minimum parameters at which all implants could be placed at bone level were 50 torque at 30 rpm and 40 torque at 50 rpm.

Two polyurethanes (PUs) were similarly synthesized by reacting a cycloaliphatic isocyanate with 1,4 butanediol and two polyols of different nature (polyester, polycarbonate diol) with molecular weights of 1000 Da. The PU made with polycarbonate diol polyol (YCD) was the only showing intrinsic self-healing at 20 °C. For assessing the mechanism of intrinsic self-healing of YCD, a structural characterization by molecular weights determination, infrared and X-ray photoelectronic spectroscopies, differential scanning calorimetry, X-ray diffraction, thermal gravimetric analysis and dynamic mechanical thermal analysis was carried out. It was concluded that the self-healing at 20 °C of YCD was due to non-covalent dynamic exchange interactions among the carbonate groups of the soft segments. Therefore, the chemical nature of the polyol played a key role in developing PUs with intrinsic self-healing at 20 °C.

Polyurethane is used extensively in the furniture industry, primarily in beds and sofas. There is a significant volume of research pertaining to the flammability of polyurethane materials, but very little regarding smoke toxicity. Given toxic fire effluents are a primary cause of injury and fatalities, more work needs to be done to test the toxicity of polyurethane materials and the fire retardants they are coated/bound with. The aim of the review is to provide a comprehensive analysis of the decomposition of polyurethane and discuss the development and application of modern fire retardants and their effect on smoke toxicity. This work then provides discussion on the challenges faced when attempting to quantify the toxicity of the effluent produced during combustion. Future work should aim to reduce the toxicity and flammability of polyurethane simultaneously by; reducing the pyrolysis of the polymer, preventing the escape of volatile products, reducing radicals within the system and lowering the temperature of the system. Before this can be achieved, a better understanding of smoke toxicity and the ability to test materials is needed.

Marine clay deposits are commonly found worldwide. Considering the cost of dumping and the related environmental concerns, an alternative solution involving the reuse of soils that have poor conditions is crucial. In this research, the authors examined the durability of marine deposited clays and compiled a corresponding database. The use of slag alone as a binder, at any percentage, increased the accumulated mass loss (ALM) up to 2%. However, the use of lime as the third binder seemed to accelerate the chemical reactions associated with the hydration of clay and cementitious material and to enhance the chemical stability, i.e., samples that included both lime and slag experienced the same ALM as samples treated with cement only. Scanning electron microscopy analysis confirmed the durability improvements of these clays. The proposed unconfined compressive strength and accumulated mass loss relationship yielded practical approximation for the fine- and coarse-grained soils blended with up to three binders until 60 days of curing.

Conventional pervious pavement materials (PPM) consist of cement and aggregate materials and are known for poor durability due to their brittle behavior. Herein, we fabricated polymeric PPMs from durable and abundant polyurethane (PU) to enhance the durability of the material and undertook mechanical and microscopic characterizations. PU-based PPM samples with varying aggregate sizes were produced and the compressive strength and water permeability of each were examined. The pore and tortuosity characteristics of the specimens were analyzed using X-ray micro-computed tomography (micro-CT). Through the micro-CT analysis, the morphological characteristics of the internal structures of PPM were identified and the correlations between the pore size distribution, connectivity, and tortuosity within the specimen were quantitatively analyzed. The microstructures derived from micro-CT were generated as a finite element model and the stress distribution generated inside was numerically determined.

A series of waterborne polyurethane (WBPU)/modified lignin amine (MLA) adhesives was prepared using modified lignin amine (MLA) as a chain extender by a prepolymer mixing process. A successful Mannich reaction was achieved during the synthesis of MLA by reacting lignin with bis(3-aminopropyl)amine. Higher tensile strength, Young’s modulus and thermal stability were recorded for WBPU/MLA adhesives with higher MLA contents. The WBPU/MLA adhesive materials were used to coat PVC substrates. The adhesive strength increased with increasing MLA content. More importantly, the MLA also enhanced the WBPU/MLA coating in terms of adhesive strength at moderately high temperatures as well as under natural weather exposed conditions. The adhesive strength was essentially unaffected with 6.48 mole% MLA in the WBPU/MLA coating after exposure to natural weather conditions for 180 days.

The design of binders plays a pivotal role in achieving enduring high power in lithium-ion batteries (LIBs) and extending their overall lifespan. This review underscores the indispensable characteristics that a binder must possess when utilized in LIBs, considering factors such as electrochemical, thermal, and dispersion stability, compatibility with electrolytes, solubility in solvents, mechanical properties, and conductivity. In the case of anode materials, binders with robust mechanical properties and elasticity are imperative to uphold electrode integrity, par-ticularly in materials experiencing substantial volume changes. For cathode materials, the se-lection of a binder hinges on the crystal structure of the cathode material. Other vital consid-erations in binder design encompass cost-effectiveness, adhesion, processability, and envi-ronmental friendliness. Incorporating low-cost, eco-friendly, and biodegradable polymers can contribute significantly to sustainable battery development. This review serves as an invaluable resource for comprehending the prerequisites of binder design in high-performance LIBs and offers insights into binder selection for diverse electrode materials. The findings and principles articulated in this review can be extrapolated to other advanced battery systems, charting a course for the development of next-generation batteries characterized by enhanced perfor-mance and sustainability.

Lithium-ion batteries (LIBs) have become indispensable energy storage devices for various applications, ranging from portable electronics to electric vehicles and renewable energy systems. The performance and reliability of LIBs depend on several key components, including the electrodes, separators, and electrolytes. Among these, the choice of binder materials for the electrodes plays a critical role in determining the overall performance and durability of LIBs. This review introduces polymer binders that have been traditionally used in the cathode, anode, and separator materials of LIBs. Furthermore, it explores the problems identified in traditional polymer binders and examines the research trends in next-generation polymer binder materials for lithium-ion battery as alternatives.

Pathogenicity is unknown for the majority of human gene variants. For prioritization of sequenced somatic and germline mutation variants, in silico approaches can be utilized. In this study, 84 million non-synonymous Single Nucleotide Variants (SNVs) in the human coding genome were annotated using consensus Variant Effect Prediction (cVEP) method. An algorithm, implemented as a stacked ensemble of supervised learners, performed combination of the 39 functional, conservation mutation impact scores from dbNSFP4.0. Adding gene indispensability score, accounting for differences in the pathogenicities of the variants in the essential and the mutation-tolerant genes, improved the predictions. For each SNV the consensus combination gives either a continuous-value pathogenicity score, or a categorical score in five classes: pathogenic, likely pathogenic, uncertain significance, likely benign, benign. The provided class database is aimed for direct use in clinical practice. The trained prediction models were 5-fold cross-validated on the evidence-based categorical annotations from the ClinVar database. The rankings of the scores based on their ability to predict pathogenicity were obtained. A two-step strategy using the rankings, scores and class annotations is suggested for filtering and prioritization of the human exome mutations in clinical and biological applications of NGS technology.

This work opens a new pathway to fabricate high dimensional stability Invar36 aerospace devices with Binder Jetting technology, for applications where temperature fluctuations directly interfere in the correct performance of high sensibility systems. Since full density part fabrication is one of the main ongoing challenges for Binder Jetting, the leading objective of this work is to study and optimise the main process parameters to increase the final density of Invar36 printed parts. Microstructural analysis and obtained density and CTE values, confirmed the feasibility to fabricate Invar36 parts.

Transparent binder is used to substitute conventional black asphalt binder and to provide light-colored pavements, whereas nano-TiO2 has the potential to promote photocatalytic and self-cleaning properties. Together, these materials provide multifunction effects and benefits when the pavement is submitted to high solar irradiation. This paper analyses the physicochemical and rheological properties of a transparent binder modified with 0.5%, 3.0%, 6.0%, and 10.0% of nano-TiO2 and compares it to the transparent base binder, and conventional and polymer modified binders (PMB) without nano-TiO2. Their penetration, softening point, dynamic viscosity, master curve, black diagram, Linear Amplitude Sweep (LAS), Multiple Stress Creep Recovery (MSCR), and Fourier-Transform Infrared Spectroscopy (FTIR) were obtained. The transparent binders (base and modified) seem to be workable considering their viscosity and exhibited values between the conventional binder and PMB regarding rutting resistance, penetration, and softening point. They showed similar behavior as the PMB, demonstrating signs of polymer-modification. The addition of TiO2 seems to reduce fatigue life, except for the 0.5% content. Nevertheless, its addition in high contents increases the rutting resistance. The TiO2 modification seems to have little effect on the chemical functional indices. The best percentage of TiO2 was 0.5%, considering fatigue and 10.0% concerning permanent deformation.

The paper covers the development of formulations and technology for low energy building materials based on the alkaline alumino-silicate binder and appropriate for special purposes. The microstructure of the binder was investigated using scanning electron microscopy and atomic force microscopy. The identification of the phase compositions was done by means of X-ray diffraction. By leach rate measurement and chemical analysis of pore liquid, the linkage of the alkali metal ions in water-insoluble composites was researched. The dependence of structure formation on mix design and curing conditions was investigated. Specific examples of manufacture and application of binder-based glues and adhesives have been considered, incl. ones for low-temperature insulating composite materials, heat insulation perlite-based materials, heat insulation of industrial boilers, and the fire resistant heat insulating system. The advantages of the binder-based temperature insulating composites compared to traditionally used ones are shown.

Concrete is the most commonly used construction material due to its various advantages, such as versatility, familiarity, strength and durability and it will continue to be in demand far into the future. However, with today’s sensitivity to the environmental protection, this material is facing unprecedented challenges due to its high greenhouse gas emission mainly during cement production. This paper investigates one of the promising cement replacement materials, alkali activated cement (AAC) concrete. Being produced mainly from byproduct materials and having a comparable structural performance to conventional concrete, AAC concrete has a potential to transform the construction industry. Mechanical properties such as compressive and flexural strength and the relationship between them are studied. Different source materials such as fly ash (FA), ground granulated blast furnace slag (GGBS), silica fume (SF) and Metakaolin (MK) are used. The effect of the source materials and the activator solutions on the concrete performance is studied. Furthermore, the freeze-thaw resistance of the concrete is studied. The results of the study showed that the behavior of AAC depends highly on the source material combinations as well as type used. The effect of the alkaline solution is also dependent on the source material used. Mixes with higher GGBS content in general showed the highest strength while mixes with MK showed the highest flexural strength. The results from the freeze-thaw test showed that proper design of AAC concrete with a lower water content is critical to achieve a good resistance.

Flue gas desulfurization gypsum (FGD gypsum) is obtained from the desulphurization of combustion gases in fossil fuel power plants. FGD gypsum can be used to produce anhydrite binder. The effect of three independent variables such as the calcination temperature of FGD gypsum (500-800 oC), the hydration time (3-28 days) and the amount of activator (0-2 %) on the compressive strength of anhydrite binder were studied. K2SO4 and Na2SO4 were used as activators. The compressive strength of anhydrite binder was evaluated using a full factorial design. The multiple linear regression models were developed to correlate the significant variables to the compressive strength of anhydrite binder. The experimental results and statistical analysis showed that the hydration time had the biggest impact on the compressive strength of anhydrite binder using K2SO4 and Na2SO4. K2SO4 made a greater influence on the compressive strength than Na2SO4. The results of modeling indicated that the individual variables had a larger effect on the compressive strength of anhydrite binder than their interaction. The mean absolute percentage error between experimental and calculated values of compressive strength was less than 10 %.

Intramedullary fixation with elastic stable intramedullary nailing and stabilization with an external fixator are standard methods for the treatment of diaphyseal femoral shaft fractures in children. A retrospective bi-centre cohort study was carried out, including all patients between the ages of 2 and 16 years with isolated traumatic diaphyseal femur fractures, treated either with intramedullary nailing or an external fixator. In total, 57 patients (17 female and 40 male) with a mean age of 6.5 ± 2.7 years (min. 2; max. 16 years) with a mean follow-up period of 6.1 ± 4.6 months (min. 2; max. 26 months), were included in this retrospective study. 33 patients were treated with elastic stable intramedullary nailing and 24 patients, and external fixation. In total, 18 patients (32%) experienced osteosynthesis-related complications: 8 patients (24%) in the elastic stable intramedullary nailing group and 10 (42%) in the external fixation group, leading to revision surgery in 10 patients (18%). At the latest follow-up, all fractures were radiologically healed with no evidence of malangulation or malrotation (defined as >20°) and full weight-bearing. There was a lower rate of complications in the ESIN group than in the external fixation group. Overall, we were unable to show a significant difference between the two methods.

Polyalcohol liquefaction can be done by acid or basic catalysis producing polyols with different properties. This study compared the mechanical properties of foams produced using polyols from liquefied Cytisus scoparius obtained by acid and basic catalysis and using two different foam catalysts. The differences were monitored using FTIR analysis. Acid-catalyzed liquefaction yielded 95.1 %, with the resultant polyol having an OH index of 1081 mg KOH/g while basic catalysis yielded 82.5 %, with a similar OH index of 1070 mg KOH/g. Generally, compressive strength with dibutyltin dilaurate (DBTDL) ranged from 16 - 31 kPa (acid-liquefied polyol) and 12 -21 kPa (base-liquefied polyol), while with stannous octoate (TIN), it ranged from 17 - 42 kPa (acid) and 29 - 68 kPa (base). Increasing water content generally decreased the compressive modulus and strength of foams. Higher water content led to a higher absorption at 1670 cm-1 in the FTIR spectrum due to the formation of urea. Higher isocyanate indices generally improved compressive strength, but high amounts led to unreacted isocyanate that could be seen by a higher absorption at 2265 cm-1 and 3290 cm-1. DBTL was shown to be the best foam catalyst due to higher trimer conversion seen in the spectra by a higher absorption at 1410 cm-1. Acid and base-derived polyols lead to different polyurethane foams with different FTIR spectra, particularly with a higher absorption at 1670 cm-1 for foams from acid-derived liquefaction.

Plasma treatment of soft polymers is the promising technique to improve biomedical properties. The response to the deformation of such materials is not yet clear. Soft elastic polyurethane treated with plasma immersion ion implantation is subjected to fatigue uniaxial loading (50000 cycles, frequency – 1 Hz, strain amplitude – 10, 20, 40%). The influence of the strain amplitude and the plasma treatment regime on damage character is discussed. Surface defects are studied in unloaded and stretched states of the material. As a result of fatigue loading, transverse cracks (with closed overlapping edges as well as with open edges deeply propagating into the polymer) and longitudinal folds which are break and bend inward, appear on the surface. Hard edges of cracks cut the soft polymer which is squeezed from the bulk to the surface.

This research investigates the application of Fused Filament Fabrication (FFF) in producing WC-10Co hardmetals, focusing binder formulations and understanding its influence on extrusion force and the influence of printing variables on green density of the samples. By examining the interplay between different binder compositions and backbone contents, the study aims to enhance the mechanical properties of the sintered parts while reducing defects inherent in the printing process. Evidence suggested that formulated feedstocks influenced the hardness of the sintered hardmetal, not due to microstructural changes but to macrostructural responses like macro defects introduced during printing, debinding and sintering of the samples. The results demonstrate the critical role of PP-MA content in improving part density and sintered hardness, suggesting the need for specific thermal debinding protocols tailored to each feedstock. The study provides insights into the formulation of feedstocks for hardmetal FFF, proposing a path toward refining manufacturing processes for better quality and performance of 3D printed hardmetal components.

Understanding the equilibrium saturation level is crucial to Binder Jetting (BJ). Saturation level influences dimensional accuracy, print time, green strength, and final material properties. Improved understanding of the saturation level can reduce development time for new materials and improve existing processes in BJ. Attempts have been made to predict saturation levels of parts with simple calculations from droplet primitives and capillary pressure. There is, however, limited experimental validation for these methods and they do not include the impact of drop velocity and droplet spacing. This study incorporates the influences of drop velocity and droplet spacing on the saturation level of the part. Drop primitives of varying droplet velocity and droplet spacing were compared. Results show that velocity impacts the feasible parameter space.

The global focus on geopolymer binder production has increased due to the adoption of waste materials and industrial byproducts. Given the gradual decline of the availability of fly ash and ground granular blast furnace slag (GGBFS) resulting from the decarbonization process in electricity and steel productions, waste clay brick powder (WCBP), could be a viable substitute of these pozzolanic by-products. This research is dedicated to thoroughly investigate the techno-eco-efficiency performance of WCBP when utilized as a geopolymer precursor. The favorable mechanical characteristics exhibited by fly ash-GGBFS-WCBP-based geopolymer binder emphasize the importance of assessing its sustainability alongside its technical viability. The study employed life cycle analysis (LCA), following ISO 14040-44 standards, and using the Simapro software, to evaluate the environmental implications of the use of WCBP-based geopolymer mixtures. Human toxicity emerged as the primary impact. Moreover, the analysis of life cycle costs highlighted key financial factors, with around 65-70% attributed to alkaline activators of the total cost. The production of alkaline activators was identified as a critical point for both environmental impact and economic considerations due to energy consumption. While WCBP-rich samples exhibit a 1.7-0.7% higher environmental impact compared to the control mix (CM), their high mechanical strength and cost-effectiveness make them technologically and economically efficient geopolymer mixes. In conclusion, the portfolio analysis for techno-eco-efficiency affirms that mixes containing 40%, 30%, and 20% WCBP are more efficient than those using 10% and 0% WCBP, respectively.

Rigid polyurethane foams were synthesized using a renewable polyol from the simple physical mixture of castor oil and crude glycerol. The effect of the catalyst and blowing agent in the foams properties was evaluated. The use of physical blowing agent (cyclopentane and n-pentane) allowed obtaining foams with smaller cells in comparison with the foams produced with a chemical blowing agent (water). The increase of water content caused a decrease of density, thermal conductivity, compressive strength and Young's modulus, which indicates that the increment of CO₂ production contributes to the formation of larger cells. Higher amount of catalyst in the foam formulations caused a slight density decrease and an increase small significance of thermal conductivity, compressive strength and Young's modulus values. These green foams presented properties that indicate a great potential to be used as thermal insulation, as density (23 - 41 kg m^-3), thermal conductivity (0.0128 – 0.0207 W m^-1 K^-1), compressive strength (45 - 188 kPa) and Young's modulus (3 - 28 kPa). These biofoams are also environmental friendly alternatives and can aggregate revenue to biodiesel industry, contributing for reduction of this fuel prices.

Mechanically strong and thermally stable films obtained from a water-based polyurethane (PU) dispersion with small (0.1–1.5 wt.%) additions of graphene oxide nanosheet (GO) were studied through elemental analysis, X-ray photoelectron spectroscopy, differential thermogravimetry, and Raman spectroscopy. Moreover, the depletion of near-surface layers in nitrogen was presented for all the samples under study. It was found that the introduction of GO into a PU matrix was ac-companied by a partial reduction of graphene oxide nanosheet and an increase in the concentra-tion of defects in its structure.

We have studied on the stress measurement by making use of salivary nitrate, which can be a candidate of stress markers, with ion-selective field-effect transistors (ISFETs). ISFETs are suitable for on-site single-drop analysis of salivary nitrate within 10 seconds. However, when ISFETs are used for salivary nitrate, ISFETs have a problem which is called the initial drift. The initial drift makes it difficult for determination of an accurate nitrate monitoring. Thus, the purpose of this study is to suppress an initial drift and to search for new easy polymer to possess more performance of sensor responses than conventional matrix membrane such as PVC. In this research, we investigated ISFETs using specific matrix membrane for example, KP-13, Pellethane^® and P7281-PU. The initial drift was evaluated from the fluctuation of the response values generated by ISFETs which are immersed in saliva or aqueous solution. As a result, P7281-PU showed its suppression effect for the initial drift in the whole saliva and various solutions. Furthermore, the cause of drift may be H⁺ diffusion, and drift suppression effect of P7281-PU may be affected by urethane bond capturing H⁺ in ion-selective membrane. This result suggests a continuous nitrate monitoring and development of wearable sensors.

Polydimethylsiloxane with hydroxy groups was functionalized to form functionalized polydimethylsiloxane, which subsequently underwent an addition reaction with isophorone diisocyanate to form the prepolymer. Next, 3-aminopropyltriethoxysilane (APTS) reacted with 3-glycidoxypropyltrimethoxysilane (GPTS) to produce bridged polysilsesquioxanes, and the sol–gel technology was employed to form hyperbranched polysiloxane nanoparticles with hydroxy groups, which was used as the additive. The hyperbranched polysiloxane and the prepolymer containing NCO functional groups then underwent an addition reaction to produce the hybrid materials. Fourier-transform infrared spectroscopy and 29Si nuclear magnetic resonance were used to characterize the structure of the polyurethane hybrid. Regarding thermal stability, after the hyperbranched polysiloxane nanoparticles was introduced, the integral procedural decomposition temperature increased from 348 ºC for polyurethane matrix to 859 ºC for the hybrid material. The results revealed that the thermal stability of the hybrid material substantially increased by approximately 247%.

Asphalt binder requires more investigation to be accurately and precisely extracted since it is a significant procedure for quality control quality assurance (QC/QA) and subsequent binder characterization. In this research, the authors provided a hands-on experience with binder extraction to deliver recommendations concerning the sensitive steps that may affect the outcomes (extracted binder content, P_be%). Based on the extraction by the centrifuge method, two mineral matter determination methods (ashing and centrifuge) were addressed. Field cores were investigated with comparing the P_be% to the actual binder content, P_ba%. Analysis of variance (ANOVA) and Tukey Post-Hoc statistical analyses, in addition to linear least square regression analysis, were used to show the significance of difference according to 38 variant cores randomly obtained from the field segments (in-service roads) via the first two weeks from the construction date. Such cores involved reclaimed asphalt pavement (RAP), reclaimed asphalt shingles (RAS), and a wide range of additives. The two extraction methods were compared with concluding that the centrifuge method was highly recommended based on a quantitative evaluation, which delivered the same average P_ba% based on the 38 cores. Furthermore, the centrifuge method provided much saving in the experimental time (almost half the time required for the ashing method). It was found that the ashing outcomes were equal to the centrifuge outcomes with disregarding the ammonium carbonate addition. Thus, it could be recommended to reassess the ammonium carbonate addition as it might excessively compensate for fake minerals that have not been lost by the ignition oven.

Diseases in articular cartilages have affected millions of people globally. Although the biochemical and cellular composition of articular cartilages is relatively simple, there is the limitation in self-repair ability of cartilage. Therefore, developing the strategies for cartilage repair is very important. Here, we reported a new manufacturing process of water-based polyurethane based photosensitive materials with hyaluronic acid and applied the materials for 3D printed customized cartilage scaffolds. The scaffold has high cytocompatibility and is one that closely mimics the mechanical properties of articular cartilages. It is suitable for culturing human Wharton's jelly mesenchymal stem cells (hWJMSCs) and the cells showed an excellent chondrogenic differentiation capacity. We consider that the 3D printing hybrid scaffolds may have potential in customized tissue engineering and facilitate the development of cartilage tissue engineering.

Polyurethane (PU) is a polymer widely used by humans whose recycling is highly complex due his chemical structure, being limited to incineration or accumulation in landfills. Biodegradation by enzymes and microorganisms has been studied for decades as an effective method of biological decomposition. In this study, Tenebrio molitor larvae (T. molitor) were fed with polyurethane foams, which gut enzymes and microorganisms were capable of degrading the polymer by 35% in 17 days of treatment, producing a weight loss of 14% in the mealworm. Changes in T. molitor gut bacterial community and diversity were observed, which may be due to colonization of species associated with PU degradation. Physical and structural biodegradation in PU by T. molitor compared to virgin PU, was demonstrated by Fourier Transform InfraRed spectroscopy (FTIR), Thermal Gravimetric Analysis (TGA) and Scanning Electron Microphotography (SEM).

The way in which a perforated structure is formed has attracted much interest in the porous membrane research community. This novel structure gives materials an excellent antifouling property as well as a low operating pressure and other benefits. Unfortunately, the current membrane fabrication methods usually involve multi-step processes and the use of organic solvents or additives. Our study is the first to offer a way to prepare perforated membrane by using a physical foaming technique with CO₂ as the blowing agent. We selected thermoplastic polyurethane (TPU) as the base material because it is a biocompatible elastomer with excellent tensility, high abrasion resistance, and good elastic resilience. Various processing parameters, which included the saturation pressure, the foaming temperature, and the membrane thickness, were applied to adjust the TPU membrane’s perforated morphology. We proposed a possible formation mechanism of the perforated membrane. The as-prepared TPU membrane had good mechanical properties with a tensile strength of about 5 MPa and an elongation at break above 100%. Such mechanical properties make this novel membrane usable as a self-standing filter device. In addition, its straight-through channel structure can separate particles and meet different separation requirements.

The utilisation of the industrial residual products to create new value-added materials and to reduce footprint is a modern challenge of science and industry. Development of the new multifunctional and bio-based composites is an excellent opportunity for complex utilisation of industrial residual products. The study describes the preparation and characterisation of the three-phases bio-based composites. The main components are bio-based binder made of peat, devulcanised crumb rubber (DCR) from used tires and part of the fly ash the cenosphere (CS). Three-phase composite prepared in the form of a block for investigation of the mechanical properties and density and a form of granules for determination of the water and oil products sorption was investigated. This work investigated the dependence of the properties on the main component DCR and CS fraction. Is found, that maximum compression strength (in block form) observed for composition without CS and DCR addition - 79.3 MPa, the second highest value of compression strength is 11.2 MPa for composition with 27.3 wt% of CS. For compositions with bio binder content from 17.4 to 55.8 wt% and with DCR contents in range from 11.0 to 62.0 wt% compression strength is in range 1.1 to 2.0 MPa. Liquid sorption analysis (water and diesel) showed that the maximum saturation of liquids in both cases is set after 35 minutes and ranges from 1.05 to 1.4 g·g -1 for water and 0.77 to 1.25 g·g-1 for diesel. It was noted that 90% of the maximum saturation with diesel fuel comes after 10 minutes and for water after 35 minutes.

The Polyurethane (PU) mixture is a high−performance engineering material with different dynamic properties compared to a hot−mixed asphalt mixture (HMA). This paper analyzed whether the Kramers−Kronig (K−K) relation and thermo−rheological simple properties were applicable to the PU mixture. Based on the result discussion, the PU mixture exhibited thermo−rheological simple properties within the test conditions. The time−temperature superposition principle (TTSP) was applicable for the PU mixture to construct the dynamic modulus master curve using the standard logistic Sigmoidal (SLS) model, the generalized logistic sigmoidal (GLS) model, and the Havriliak−Negami (HN) model. The Hilbert integral transformed SLS and GLS models for the phase angle can accurately fit the measured phase angle data with newly fitted shift factors and predict the phase angle within the viscoelastic range. The Core−Core and black space diagrams both displayed single continuous smooth curves, which can be utilized to characterize the viscoelastic property of the PU mixture. The K−K relation is applicable for the PU mixture to obtain the phase angle master curve model, storage modulus, and loss modulus from the complex modulus test results. The phase angle of the PU mixture cannot be derived from the dynamic modulus data and currently needs to be derived from the laboratory measurement.

Soft materials bearing rigid, lightweight, and vibration-dampening properties offer distinct advantages over traditional wooden and metal-based fillings for spent fuel transport casks, due to their low density, tunable structure, excellent mechanical properties, and ease of processing. In this study, a novel type of rigid polyurethane foams is prepared using a conventional polycondensation reaction between isocyanate and hydroxy groups. Moreover, the density and size of the pore in these foams are precisely controlled through simultaneous gas generation. The as-prepared polyurethane exhibits high thermal stability exceeding 185 °C. Lifetime predictions based on thermal testing indicate that these polyurethane foams could last up to over 60 years, which is double lifetime of conventional materials of about 30 years. Due to their occlusive structure, the mechanical properties of these polymeric materials meet the design standards for spent fuel transport casks, with maximum compression and tensile stresses of 6.89 and 1.37 MPa, respectively, at a testing temperature of -40 °C. In addition, these polymers exhibit effective flame retardancy; combustion ceased within 2 s after removal of the ignition source. All in all, this study provides a simple strategy for preparing rigid polymeric foams, presenting them as promising prospects for application in spent fuel transport casks.

Background: The current standard technique for vascular grafting in cerebral revascularization surgery is through the interposition of an autologous blood vessel. Technical complications have necessitated the development of a synthetic alternative, but classical biomaterials are not suited for small caliber vascular grafting due to neointimal hyperplasia and thrombosis. Electrospinning of polymers is a promising technique for the development of small vascular grafts. The in vivo performance and efficacy of electrospun polyurethane (ePU) grafts with an internal diameter of < 1.5 mm have thus far not been evaluated. Methods: We developed a novel ePU graft with a diameter of 1.25 mm for implantation into the infrarenal aorta of rats. Results: Patency rates of grafts after a four-month-period were equal to those reported in other studies with larger ePU graft diameters, and equal or higher than in studies with other biomaterials. We observed some loss in flow velocity throughout the grafts, which suggests a decreased elasticity of the graft compared to native rat aorta. However, the grafts demonstrated good neo-endothelialization and minimal neointimal hyperplasia. Their porosity promoted cellular infiltration, as shown on tissue slide examination. Conclusion: Our results show that ePU vascular grafts with internal diameter of < 1.5 mm are promising candidates for vascular grafting in cerebral revascularization surgery.

The kinetic analysis of octogen coating with a polyurethane base containing hydroxyl-terminated polybutadi-ene (HTPB) was investigated using infrared spectroscopy. The coating process involved a solvent method, where octogen and liquid polyurethane were mixed, the solvent was evaporated, and curing took place at an elevated temperature. The ratio of HTPB to diisocyanate was equimolar. Initially, the curing process occurred in the solvent system, followed by further curing in the bulk system. The kinetic analysis was performed using a modified diffusion-autocatalytic model, which includes non-catalytic, autocatalytic, and diffusion compo-nents. This model was compared with others during the bulk reaction and proved to be effective in correcting errors, particularly in the gel time region. Thermodynamic parameters were evaluated using the Arrhenius and Eyring equations. The reaction rate was initially controlled by chemical reactivity, but after the gel time, diffusion became the controlling factor. In the HTPB-TDI system, both the non-catalytic and autocatalytic parts decreased with increasing temperature, while diffusivity increased. It is worth noting that diffusivity is temperature-dependent. Different diisocyanates, namely toluene diisocyanate (TDI), isophorone diisocyanate (IPDI), and hexamethylene diisocyanate (HMDI), were studied, revealing that HMDI exhibited higher reactivi-ty than TDI and IPDI. The catalyst effect on reaction rate HTPB-TDI system is investigated. Catalysts adding (0.1%) to HTPB-TDI system is really decrease their activation energy by efectivity DBTL>FeAA>TPB. Catalyst not change their diffusivity.

The production of polyurethane films from bark-derived polyols requires the complete solubility of all components in the polyurethane synthesis media. In this study, a comprehensive investigation was conducted to achieve the copolymerization of black alder bark water extract-derived polyol with isocyanate for polyurethane film synthesis in THF solution. A fractionation approach using tetrahydrofuran (THF) as a solvent was employed to dissolve the extract, followed by filtration and removal of the solvent. The resulting THF-soluble fraction comprised 62±1% of the dry weight of the alder bark extract, mainly consisting of the xyloside form of the diarylheptanoid compound oregonin, along with oligomeric flavonoids and carbohydrates. The THF-insoluble fraction was the most enriched with carbohydrate compounds, followed by the crude extract and THF-soluble fraction. Another approach was aimed at obtaining bark extractives based liquid polyols suitable for producing rigid PU foams. For this purpose, oven-dried crude black alder bark water extract was liquefied with polyethylene glycol (PEG 400). The liquefaction of black alder bark and pine bark extractives was studied under different conditions, including varying temperature ranges (130-170⁰C), catalyst concentrations (0-1,5%), and bark extract content in the mixture (15-30%). The results showed that the use of sulphuric acid as a catalyst (1-1.5%) significantly improved the solubility of both extractives, enabling the attainment of extract concentrations up to 25% at 170⁰C. However, increasing the extract content beyond a certain threshold led to incomplete solubility. It was shown that the PEG-insoluble fractions consist mainly of carbohydrate components. To increase the content of biomass in liquid polyols, the effect of glycerol additions into the liquefaction agent is under study. The findings provide insights into tailoring bark-sourced polyols for polyurethane foam production through appropriate liquefaction conditions.

In the European Union, the demand for polyurethane is continually growing. In 2017, the estimated production value of polyurethane was 700,400T, of which 27.3% is taken to landfill, which causes an environmental problem. In this paper the behaviour of various polyurethane foams from the waste of different types of industries will be analysed with the aim of assessing their potential use in construction materials. In order to this, the wastes were chemically tested by means of CHNS, TGA, and leaching tests. They were tested microstructurally by means of SEM. The processing parameters of the waste was calculated after finding out its granulometry and its physical properties i.e. density and water absorption capacity. In addition, the possibility of incorporating these wastes in plaster matrices was studied by determining its rendering in an operational context, finding out its mechanical resistance to flexion and compression at 7 days, its reaction to fire as well as its weight per unit of area and its thermal behaviour. The results show that in all cases, the waste is inert and does not undergo leaching. The generation process of the waste determines the foam’s microstructure in addition to its physical-chemical properties that directly affect building materials in which they are included, thus offering different ways in which they can be applied.

Polyurethane (PU) foam adhesives were prepared from castor oil as a polyol with isocyanate poly (4,4′-methylene diphenyl isocyanate) (PMDI) using a solvent-free process. The NCO/OH molar ratio used for the preparation of PU foams was 1.5. Water, organosiloxane and dibutyltin dilaurate were blowing agent, surfactant and catalyst, respectively. Effects of the ratio of blowing agent and catalyst were adjusted to optimize the properties. The results show that 4 wt% of castor oil of catalyst and blowing agent minimizes water absorption and maximizes volume expansion in the PU foams. FT-IR analysis shows that urethane bond was formed by hydroxyl group of castor oil and –NCO group of isocyanate PMDI. More blowing agent and catalyst could improve the volume expansion ratio and reduce water retention of PU foams. It was found that Moso bamboo charcoal (Phyllostachys pubescens) or/and China fir wood particle (Cunninghamia lanceolate) composites with setting densities of 500 and 600 kg/m³ can be prepared from optimized castor oil-based PU foam adhesive at 100 °C for 5 min under a pressure of 1.5 MPa. Increasing the amount of bamboo charcoal decreases the equilibrium moisture content, water absorption and internal bonding strength of the composite. Notably, bamboo charcoal composite exhibits excellent dimensional stability. The optimized density and bamboo charcoal percentages of the composite were 500 kg/m³ and 50 to 100%. The castor oil-based PU composites containing bamboo charcoal fulfilled the CNS 2215 standards for particleboard. This dimensionally stable, low-density bamboo charcoal composite has high potential to replace current indoor building materials.

Asphalt cement will not last for a long time as the world encounters a diminishment in the crude oil. For sustainable, flexible pavement development, new resources can provide a contribution to replace it partially or entirely. In this study, asphalt was partially and entirely replaced by guayule resin as a bioresource by-product, extracted during the guayule natural rubber production. Crumb rubber modifier (CRM) was used as an asphalt enhancer. The Superpave grading system was followed at high, intermediate, and low temperatures to evaluate such innovative binder for rutting, fatigue, and thermal cracking, respectively, in addition to viscosity. Therefore, the original, short-term aging and long-term aging were simulated using tank, rolling thin film oven, and pressure aging vessel materials. Additionally, component analysis using Fourier-transform infrared spectroscopy was provided to link the rheological properties with the chemical changes. Outcomes showed a relatively much lower viscosity of guayule in the same high-temperature asphalt grade indicating savings in plant energy consumption and reduced environmental emissions. CRM enhanced guayule, but not as much as asphalt, proven by polymeric component migration through liquid binder. This enhancement was reflected in the rheological performance besides other factors. As-received guayule seems to have high oxygen content proven by strong absorption peak intensities of oxidative bonds (e.g., Carbonyl and sulfoxide). Such pre-oxidation was negatively reflected in the intermediate- and low-temperature performance of guayule and guayule-based binders. However, the investigated guayule had potential to compensate for asphalt replacement in the presence of CRM by 23–42% by weight of blend.

Fiber-based flexible sensors have promising applications potential in human motion and healthcare monitoring, owing to their merits of lightweight, flexibility, and easy processing. Now, high-performance elastic fiber-based strain sensors with high sensitivity, large working range and excellent durability are in great demand. Herein, we have easily and quickly prepared a highly-sensitive, durable fiber-based strain sensor by dip-coating of highly-stretchable polyurethane (PU) elastic fiber in MXene/ waterborne polyurethane (WPU) dispersion solution. Benefiting from the electrostatic repulsion force between the negatively charged WPU and MXene sheets in the mixed solution, very homogeneous and stable MXene/WPU dispersion was successfully obtained and the interconnected conducting networks were correspondingly formed in coated MXene/WPU shell layer, which makes as-prepared strain sensor exhibit a gauge factor of over 960, a large sensing range of over 90% and detection limit as low as 0.5% strain. As elastic fiber and mixed solution have the same polymer constitute, tight bonding of MXene/WPU conductive composite on PU fibers was achieved, enabling the as-prepared strain sensor endure over 2500 stretching-releasing cycles and thus show good durability. Full-scale human motion detection was also performed by the strain sensor, and a body posture monitoring, analysis, and correction prototype system was developed via embedding the fiber-based strain sensors into sweater, strongly indicating the great application prospect in exercise, sports and healthcare.

Due to the growing interest in biopolymers, biosynthesizable and biodegradable polymers currently occupy a special place. Unfortunately, the properties of native biopolymers are not satisfactory, which explain that attempts are being made to modify them. The work attempts to improve the properties of poly(3-hydroxybutyrate) (P3HB) using linear aliphatic polyurethane (PU) based on 1,4-butanediol and hexamethylene 1,6-diisocyanate. The conducted studies on the effect of the amount of PU used (5, 10, 15 and 20 wt.%) showed an improvement in the thermal properties of the prepared polymer blends. There was an increase in the degradation temperature of the ob-tained blends in relation to the native P3HB by 12-57C, and the difference between the melting point and the degradation point was above 100°C for most of the obtained blends. As part of the tested mechanical properties of the new polymer blends, we noted the desired increase in the tensile strength, in the relative elongation at break and in the impact strength with a decrease in hardness, in particular with the presence of 5 wt.% PU. Therefore, for further improvement, hybrid nanobiocomposites with 5 wt.% PU and organically modified montmorillonite (MMT – Cloisite 30B) were produced. The nanoadditive was used in typical amount of 1-3 wt.%. The nanostructure of the biocomposites produced by extrusion was examined by small-angle X-ray scattering (SAXS) and transmission electron microscopy (TEM), the morphology by scanning electron microscopy (SEM), and compatibility by infrared spectroscopy (FT IR). In addition, selected mechanical properties were determined and thermal properties were tested by the thermogravimetric analysis (TGA) and the standard differential scanning calorimetry (DSC). The polyester and polyurethane chains penetrated into the interlayer spaces of organically modi-fied nanoclay – Cloisite30B and the complete delamination occurred during direct mixing in the extrusion process. FT IR spectral analysis showed the compatibility of the polymer biocomposite components by the coexistence of intermolecular interactions in the form of hydrogen bonds. The morphology studies of the produced hybrid nanobiocomposites showed an interaction of the bi-opolymer matrix with PU and Cloisite30B and the formation of easily migrating polyester-polyurethane-montmorillonite adducts, which resulted in improved mechanical properties com-pared to the properties of the native P3HB and P3HB-PU compositions. The influence of the presence of a nanofiller on the properties of the prepared nanobiocomposites was tested and it was found that, as expected, the smallest amount of nanofiller provides the best results.It was found that the obtained nanobiocomposites containing the smallest amount of nano-fillers, i.e. 1 wt.% Cloisite30B exhibited the best mechanical and thermal properties. The desired decrease in hardness by 15% and a higher value of impact strength by 15%, an increase in elonga-tion at break by 60% and an increase in thermal stability of the newly produced biocomposites compared to to the native P3HB were observed. The prepared nanobiocomposites combined the best features caused by the elasticizing effect of polyurethane and the formation of P3HB-PU-MMT adducts.

The NCO functional group of 3-isocyanatoproply triethoxysilane (IPTS) and the OH functional group of DOPO-BQ were used to conduct an addition reaction. Following completion of the reaction, triglycidyl isocyanurate (TGIC) was introduced to conduct a ring-opening reaction. Subsequently, a sol-gel method was used to take place a hydrolysis- condensation reaction on TGIC-IPTS-DOPO-BQ to form a hyperbranched nitrogen–phosphorous–silicon (HBNPSi) flame retardant. This flame retardant was incorporated into a polyurethane (PU) matrix to prepare a hybrid material. Fourier-transform infrared spectroscopy (FT-IR), thermogravimetric analysis (TGA), limiting oxygen index (LOI), UV-VIS spectrophotometry, and Raman analysis were conducted to structure characterization and analyzed transparency, thermal stability, flame retardancy, and residual char to understand the flame retardant mechanism of prepared hybrid materials. After the flame retardant was added, the maximum degradation rate decreased from −36 wt%/min to −17 wt%/min, the integral procedure decomposition temperature (IPDT) increased from 348 ℃ to 488 ℃, and the char yield increased from 0.7 to 8.1 wt%. The aforementioned results verified that thermal stability of PU can be improved after adding HBNPSi. The LOI analysis indicated that the pristine PU was flammable because the LOI of pristine PU was only 19. When the content of added HBNPSi was 40%, the LOI value was 26; thus the PU hybrid became nonflammable.

Organophilic nano clay is the composition of mostly clay and organic molecules designed to improve various materials' physical and chemical properties. Permanent deformation in asphalt pavements is primarily the result of inadequate compaction, excessive loading, and high temperatures. Rutting can result in aquaplaning, leading to accidents and costly maintenance and rehabilitation works that drain the economy. Such behavior of asphalt pavements may be attributable to poor selection of aggregate, asphalt binder, or substandard asphalt binders. This study used different percentages of organophilic nano clay ranging from 3.0% - 5.0% with two penetration grade bitumen, i.e., N.R.L 60-70 &amp; N.R.L 80-100. Adding organophilic nano clay to asphalt binder significantly reduced the rutting potential under cyclic loading at high temperatures (55 °C). Ten modified formulations and two virgin bitumen specimens were prepared. The modified binders' viscosity and rutting were tested using the Rotational Viscometer and Wheel Tracker Test (W.T.T.), respectively. The results were analyzed using software for Statistical Analysis. It was recorded that organophilic nano clay-modified bitumen significantly affected rutting to interpret the results. The results indicated that rutting decreased and viscosity increased in all nano clay-modified bitumen samples, with a 4.5% O.N.C modified binder showing the most significant improvement.

Benign design of alkali-activated slag/FA geopolymer paste has intriguing increasing attention for optimizing its service performance. Therefore, the replacement of fly ash (FA) with 10 wt% silica fume (SF) is investigated by mechanical strength after freeze-thawing cycles and microstructure characterization. The results show that an appropriate dosage (30 wt%) of slag is necessary to attain alkali-activated slag/FA geopolymer paste with excellent mechanical performance, and the SF/slag/FA (SF: slag: FA= 10:30:60, wt%) geopolymer paste exerts the compressive and flexural strength of 95.2 and 3.2 MPa, respectively. Meanwhile, the doped 10 wt% SF facilitates the propagation of (N, C)-A–S–H chains, rather than the formation of C-S-H gels, evidenced by the absent exothermic peak at about 861oC from the differential scanning calorimetry (DSC) curves, leading to the increases in the pores volume with a pore diameter<20 nm and tortuosity by mercury intrusion porosimeter (MIP) results, corresponding to an improved freezing-thawing resistance with the residual compressive strength of 52.8 MPa and the weight loss of 10.5% after 300 freeze-thawing cycles. It explores a cost-effective and benign facile approach to designing heating curing-free alkali-activated slag/FA geopolymer paste with good freezing-thawing resistance.

Existing rammed earth construction methods have disadvantages such as increased initial costs for manufacturing the large formwork and increased labor costs owing to the labor-intensive construction techniques involved. To address the limitations of existing rammed earth construction methods, an autonomous rammed earth construction method is introduced herein. As this autonomous rammed earth construction method uses a modular formwork, alternative materials must be used in the construction to satisfy the requirements for the early-age binder performance. Accordingly, this study evaluates the use of an epoxy emulsion composed of epoxy and a hardener to enhance the performance of the binder. Preliminary experiments were conducted to determine the optimal formulation of the epoxy emulsion, following which the compressive strength, water loosening, shrinkage, rate of mass change, and microstructure of several red clay binder specimens with and without epoxy emulsion were analyzed at early ages. The results confirmed that the epoxy emulsion can be applied to satisfy the performance requirements for autonomous rammed earth construction by improving the durability and strength of the binder at early ages.

Binder jet printed components typically have low overall density in the green state and high shrinkage and deformation after heat treatment. It has previously been demonstrated that, by including nanoparticles of the same material in the binder, these properties can be improved as the nanoparticles can fill the interstices and pore throats between the bed particles. The beneficial effects from using these additive binder particles can be improved by maximising the binder particle size, enabling the space within the powder bed to be filled with a higher packing efficiency. The selection of maximum particle size for a binder requires detailed knowledge of the pores and pore throats between the powder bed particles. In this paper, a raindrop model is developed to determine the critical radius at which binder particles can pass between pores and penetrate the bed. The model is validated against helium pycnometry measurements and binder particle drop tests. It is found that the critical radius can be predicted, with acceptable accuracy, using a linear function of the mean and standard deviation of the particle radii. Percolation theory concepts have been employed in order to generalise the results for powder beds that have different mean particle sizes and size distributions. The results of this work can be employed to inform the selection of particle sizes required for binder formulations, to optimise density and reduce shrinkage in printed binder jet components.

Smart flexible materials with piezoresistive property are increasingly used in sensors field. When embedded in structures, they would allow an in-situ structural health monitoring and damage assessment of impact loading such as crash, bird strikes and ballistic impacts. However, this could not be achieved without a deep characterization of the relation between piezoresistivity and mechanical behavior. The aim of this paper is to study the potential use of the piezoresistivity effect of a conductive foam made of a flexible polyurethane matrix filled with active carbon for integrated Structural Health Monitoring (SHM) and damage assessment applications. To do so, PolyUrethane Foam filled with Active Carbon, namely PUF-AC, are manufactured and tested under quasi-static compression tests and under Dynamic Mechanical Analyser (DMA) with in-situ measurement of its resistivity during tests. A relation is proposed for describing the evolution of the resistivity versus strain and stress. In addition, a demonstrative experiment of a PUF-AC sample subjected to low velocity impact assesses the interest of this type of materials for damage assessments.

Nowadays, the chemical industry is looking for sustainable chemicals to synthesize nanocomposite bio-based polyurethane foams, PUs, with the aim to replace the conventional petrochemical precursors. Some possibilities to increase the environmental sustainability in the synthesis of nanocomposite PUs include the use of chemicals and additives derived from renewable sources (such as vegetable oils or biomass wastes) which comprise an increasing wider base raw materials. Generally, sustainable PUs exhibit chemico-physical, mechanical and functional properties which are not comparable with those of PUs produced from petrochemical precursors. In order to enhance the performances as well as the bio-based aspect, the addition in the polyurethane formulation of renewable or natural fillers can be considered. Among these, walnut shells and cellulose are very popular wood-based waste and due to their chemical composition, carbohydrate, protein and/or fatty acid, can be used as reactive fillers in the synthesis of PUs, diatomite as natural inorganic nanoporous filler can be also evaluated to improve mechanical and thermal insulation properties of rigid PUs. In this respect, sustainable nanocomposite rigid PU foams are synthesized by using a cardanol-based Mannich polyol, MDI as isocyanate source, catalysts and surfactant to regulate the polymerization and blowing reactions, H2O as sustainable blowing agent and suitable amount (5wt%) of ultramilled walnut shell, cellulose and diatomite as filler. The effect of these fillers on the chemico-physical, morphological, mechanical and functional performances on PU foams has been analyzed.

Asphalt binder is a temperature sensitive material, whose performance is greatly affected by the climate change of the environment. Improper selection of asphalt will cause a lot of damage and affect the durability of the road. The establishment of asphalt pavement performance zoning in Xinjiang, a vast area with great temperature difference, will provide reference for the selection of asphalt suitability, the refinement of pavement design and the sustainable development of road engineering. In this study, 11 years of temperature data in Xinjiang region were collected and analyzed, and 98% reliability of pavement design temperature was used to draw a performance grading map of asphalt pavement in Xinjiang region based on ArcGIS platform. Finally, Xinjiang region was divided into 9 performance zones. At the same time, the performance grade (PG) of five kinds of asphalt binders in Karamay were explored. The result shows that there is little difference in continuous PG span between different matrix asphalt binders, the lower penetration grade, the better high temperature performance, the worse low temperature performance. After adding SBS modifier, the continuous PG span can be higher than the matrix asphalt in 20 ℃. All these provide the basis for reasonable selection of asphalt binders in different areas of Xinjiang.

This paper presents a proof-of-concept study on the biocolonization of 3D-printed hydroxyapatite scaffolds with mesenchymal stem cells (MSCs). Three-dimensional (3D) printed biomimetic bone structure made of Calcium Deficient HydroxyApatite (CDHA) intended as future bone graft was made from newly developed composite material for FDM printing. The biopolymer polyvinyl alcohol serves in this material as a thermoplastic binder for 3D molding of the printed object with a passive function and is completely removed during sintering. The study presents the material, the process of fused deposition modeling (FDM) of CDHA scaffolds and its post-processing at three temperatures (1200, 1300, 1400 °C), as well it evaluates the cytotoxicity and biocompatibility of scaffolds with MTT and LDH release assays after 14 days. The study also includes a morphological evaluation of the cellular colonization with scanning electron microscopy (SEM) in two different filament orientations (rectilinear and gyroid). The results of the MTT assay showed that the tested material was not toxic, and cells were preserved in both orientations, with most cells present on the material fired at 1300°C. Results of the LDH release assay showed a slight increase in LDH leakage from all samples. Visual evaluation of SEM confirmed the ideal post-processing temperature of the 3D-printed FDM framework for samples fired at 1300°C and 1400°C, with a porosity of 0.3 mm between filaments. In conclusion, the presented fabrication and colonization of CDHA scaffolds have great potential to be used in the tissue engineering of bones.

Vertically aligned Fe, S, and Fe-S doped anatase TiO₂ nanotube arrays are prepared by electrochemical anodization process using an organic electrolyte in which lactic acid is added as an additive. In the electrolyte, nanotube layers of greater length (12 μm) and high order with inner diameter of approx. 90 nm and outer diameter of approx. 170 nm are achieved. Doping of Fe, S, and Fe-S via simple wet impregnation method substituted Ti and O sites with Fe and S, which leads to enhance the rate performance at high discharge current densities. Discharge capacities of TiO₂ tubes increased from 82 mAh g-1 (bare) to 165 mAh g-1 for Fe-S doped TiO₂ at high current densities of 0.3 mAcm-2 after 100 cycles with exceptional capacity retention of 85% after 100 cycles. Owing to the enhancement of thermodynamic and kinetic properties by doping of Fe-S, Li-diffusion increas2ed resulting in remarkable discharge capacities of 143 mAh g-1 and 89 mAh g-1 at a current density of 7.4 mA cm-2 and 19 mA cm-2, respectively.

This research seeks to interpret the component analysis of an innovative bio-asphalt binder using guayule resin in addition to crumb rubber modifier (CRM) at high concentrations. Such asphalt modification aims to minimize the dependency on virgin asphalt binder and provide new solutions concerning sustainable, flexible pavement industry. Guayule resin is a promising bioresource for asphalt binder replacement. By now, it could be considered a no value byproduct extracted during the guayule natural rubber production. CRM is a recycled material derived from scrap tires. The provided interpretation could help in understanding the asphalt-rubber-guayule interaction mechanism. Fourier transform infrared spectroscopy (FTIR), supported by thermo-gravimetric analysis (TGA), was used to investigate the component analyses of guayule resin composition, asphalt guayule interaction, and asphalt rubber guayule interaction, compared to corresponding asphalt rubber interaction. Additionally, the rheological properties at elevated temperatures were provided to link the microscale properties with the final product performance. The study clarified the distinct carbon and hydrogen compositional elements of guayule resin. Asphalt and guayule resin have similarities in chemical composition and rheological behavior with temperature susceptibility. The asphalt guayule binder had physical interaction. However, when both interacted with rubber, a chemical interaction was attributed, with no difference in rubber dissolution tendency, in asphalt rubber guayule, compared to asphalt rubber. A bio-binder composed of 62.5% asphalt, 25% guayule and 12.5% CRM had the potential to provide rheological properties better than base asphalt. Such behavior was interpreted by a high release of rubber components.

Dye wastewater containing bisphenol A (BPA) and dyes as pollutants have not been adequately studied. Our previous study revealed that thermoplastic polyurethane (TPU) nanofiber membranes (NFMs) modified by the addition of polyethyleneimine (PEI) and polydopamine (PDA) satisfactorily adsorb dyes. Herein, we first optimized the synthesis conditions for such membranes, noting a PEI:PDA monomer ratio of 2:2 and a deposition time of 48 h to be optimal. Experiments using these membranes revealed that binary systems containing BPA and the dyes (Congo red (CR), Eosin yellow (EY), or sunset yellow (SY)) exhibit three adsorption behaviors. CR and BPA compete with each other for adsorption sites, decreasing the maximum adsorption capacity (Qmax) for CR 208.3 mg/g (in a monomeric system) to 182.4 mg/g, whereas for BPA, it decreased from 26.7 to 22.8 mg/g. The adsorption rates for CR and BPA decreased from 0.002 min−1 and 0.331 min−1 in the monomeric systems to 8.37 × 10−4 min−1 and 0.072 min−1, respectively, in the binary CR–BPA system, exhibiting antagonistic effects. When EY and BPA coexist, Qmax for EY increased from 60.0 (monomeric) to 71.9 mg/g, whereas that for BPA increased from 35.6 to 43.2 mg/g, showing a synergistic effect due to the possible bridging effect. The adsorption sites for SY and BPA are independent of each other. Thus, PDA/PEI TPU NFMs exhibit the potential for removal of dye–BPA composites, whereas binary systems containing BPA with different dyes are adsorbed differently.

Producing complex shaped tungsten carbide cobalt (WC-Co) tools by classical technologies is difficult and often impossible due to their high hardness and brittle fracture behavior. Additive Manufacturing (AM) is a suitable technology for creating complex structures and simultaneously shortening expensive machining processes. Binder Jetting (BJ) is an innovative AM technology that offers several advantages over laser-based processes, for example low manufacturing costs and high build-up rates. Binders with nanoparticle additives have already proven to be effective in in- creasing the packing density of the powder bed and improving the sintering properties. Addition- ally, they offer the possibility of selectively changing the material composition in the part. This paper presents a concept for the use of nanoparticles to generate gradients in the green compact, which leads to a cobalt gradient in the part after sintering. The possibility of introducing particles locally into complex structures allows local modification of the material properties.

Traditional metals such as stainless steel, titanium and cobalt chrome are used in biomedical applications (implants, scaffolds etc.) but suffer from issues such as osseointegration and compatibility with existing bone. One way to improve traditional biomaterials is to incorporate ceramics with these metals so that their mechanical properties can be similar to cortical bones. Tricalcium phosphate is such a ceramic with properties so that it can be used in human body. This research explores the use of binder jetting based additive manufacturing process to create a novel biocomposite made of cobalt chrome and tricalcium phosphate. Experiments were conducted and processing parameters were varied to study their effect on the printing of this biocomposite. Layer thickness, binder saturation and drying time affected the dimensional tolerance and the density of the green samples. This effect is important to understand so that the material can be optimized for use in specific applications.

In this study we investigated the potential of two non-edible oil extracts from seeds of Colliguaya Integerrima (CIO) and Colliguaja Salicifolia (CSO) to use as a renewable source for polyols and eventually polyurethane foams or biodiesel. For this purpose, two novel polyols from the aforementioned oils were obtained in a one-single step reaction using a mixture of hydrogen peroxide and acetic acid. The polyol derivatives obtained from the two studied oils were characterized by spectral (FT-IR, ¹H NMR and ¹³C NMR), physico-chemical (e.g. chromatographic analysis, acid value, oxidizability values, iodine value, peroxide value, saponification number, kinematic viscosity, theorical molecular weights, density, hydroxyl number and hydroxyl functionality) and thermal (TGA) analyses according to standard methods. Physico-chemical results revealed that all parameters, with the exception of the iodine value, were higher for bio-polyols (CSP and CIP polyols) compared to the starting oils. The NMR, TGA and FT-IR analyses demonstrated the formation of polyols. Finally, the OH functionality values for CIP and CSP polyols were 4.50 and 5.00, respectively. This result indicated the possible used of CIP and CSP polyols as a raw material for the preparation of polyurethane rigid foams.

In this work we have investigated the role of various additives (emulsifier, anti-dripping agent) and formulation procedure (pre- dispersion of solid additives in polyol via milling) which influence the flame retardancy of 6,6′-[ethan-1,2-diylbis(azandiyl)]bis(6H-dibenzo[c,e][1,2]oxaphosphin-6-oxid) (EDA-DOPO) containing flexible polyurethane foams. For comparison, the flame retardancy of two additional structurally analogues bridged 9, 10-dihydro-9-oxa-10-phosphaphenanthrene-10-oxide (DOPO) based compounds i.e. ethanolamine-DOPO (ETA-DOPO) and ethylene glycol-DOPO (EG-DOPO) were also evaluated together with EDA-DOPO in flexible PU foams of various formulations. The flame retardancy of three bridged-DOPO compounds depends on the type of PU formulation. For certain PU formulation containing EDA-DOPO, lower fire performance was observed. Addition of emulsifier and polytetrafluoroethylene (PTFE) to these PU formulations influenced positively the flame retardancy of EDA-DOPO/PU foams. In addition, dispersion of EDA-DOPO and PTFE via milling in polyol improved the flame retardancy of the PU foams. Mechanistic studies performed using pyrolysis combustion flow calorimetry (PCFC) and its coupling to FTIR showed no difference in the combustion efficiency of the bridged-DOPO compounds in PU foams. From these PCFC experiments we can conclude that these bridged-DOPO compounds and their decomposition products may work primarily in the gas phase as flame inhibitors. Physiochemical behavior of additives in PU formulation responsible for the improvement in the flame retardancy of PU foams was further investigated by studying the dripping behavior of the PU foams in UL 94 HB test. A high-speed camera was used to study the dripping behavior in the UL 94 HB test and results indicate a considerable reduction of a total number of melt drips and flaming drips for the flame retardant formulations. This reduction in melt drips and flaming drips during the UL 94 HB tests help PU foams achieve higher fire classification.

One of the main benefits of binder jetting is the ability to print quickly compared to other metal additive manufacturing methods. Demand for higher throughput continues to increase, but the effects of faster print speeds on part outcomes are not yet clearly understood. MIM powders are used to achieve optimal density and surface finish. Printing at slower speeds results in densities near 98% and average surface roughness values as low as 4 μm (Ra), in the as-sintered condition. In this study, spread speeds were varied in order to understand the effect of print speed on surface roughness. 316L D90 -22 μm powder was used to print with 3 different spread speeds, 2 different layer thicknesses, and 2 different printhead droplet sizes. The surface finish and density were quantified for the sintered parts that were oriented at 0, 22.5, and 45 degrees with respect to the Z- direction.

Understanding the interplay among organophosphorus flame-retardants (OPFRs), microplastics, and freshwater organisms is crucial for unravelling the dynamics within freshwater environments and foreseeing the potential impacts of organic pollutants and plastic contamination. For that purpose, the present research assessed the exposure impact of 10 mg L–1 flame-retardant alumin-ium diethylphosphinate (ALPI), 10 μg mg–1liver microplastics polyurethane (PU), and the combina-tion of ALPI and PU on the freshwater planarian Girardia tigrina. The exposure of G. tigrina to both ALPI and PU revealed a sequential effect, i.e., a decrease in locomotor activity, while other molecular biomarkers (oxidative stress biomarkers and metabolic response) remained unaffected. Despite this fact, it was possible to observe that the range (min-max) of responses of exposed or-ganisms were altered, in the particular case of electron transport system, cholinesterase activity, glutathione S-transferase, catalase and levels of total glutathione and proteins, showing that the energetic costs for detoxification and antioxidant capacity might be causing less energy allocated for the planarian activity. By examining the physiological, behavioural, and ecological responses of planarians to these pollutants, insights can be gained into broader ecosystem-level effects and inform strategies for mitigating environmental risks associated with OPFRs and microplastic pol-lution in freshwater environments.

This study used the sol–gel method to synthesize a non-halogenated hyperbranched flame retardant containing nitrogen, phosphorus and silicon, HBNPSi, which was then added to a polyurethane (PU) matrix to form an organic–inorganic hybrid material. Using 29Si nuclear magnetic resonance, energy-dispersive X-ray spectroscopy of P- and Si-mapping, scanning electron microscopy, and X-ray photoelectron spectroscopy, this study determined the organic and inorganic dispersity, morphology, and flame retardance mechanism of the hybrid material. The condensation density of the hybrid material PU/HBNPSi was found to be 74.4%. High condensation density indicates a dense network structure of the material. The P- and Si-mapping showed that adding inorganic additives in quantities of either 20% or 40% results in homogeneous dispersion of the inorganic fillers in the polymer matrix without agglomeration, indicating that the organic and inorganic phases had excellent compatibility. In the burning test, adding HBNPSi to PU resulted in the material passing the UL-94 standard at the V2 level, unlike the pristine PU, which did not meet the standard. The results demonstrated that after non-halogenated flame retardant was added to PU, the material’s flammability and dripping were lower, thereby proving that flame retardants containing elements such as nitrogen, phosphorus, and silicon exert an excellent flame retardant synergistic effect.

This paper investigates the density, phase composition, microstructure and mechanical properties (microhardness, fracture toughness) of binderless WC + SiC ceramics obtained by conventional pressureless sintering (CPS) and Spark Plasma Sintering (SPS). α-WC nanopowders obtained by DC arc plasma chemical synthesis and β-SiC powders have been used as raw materials. The content of SiC particles was 1, 3, 5% wt. Excess graphite (0.3, 0.5% wt.) was added to α-WC nanopowders to decrease the volume fraction of W2C particles that negatively affect the mechanical properties of ceramics. WC + 1% wt. SiC + 0.3% wt. C ceramics are shown to have a homogeneous fine-grained microstructure, high relative density, increased microhardness and Palmquist fracture toughness. The CPS and SPS activation energies of WC + SiC nanopowders at an intensive shrinkage stage are determined using the Young-Cutler model. The effect of carbon and SiC particles on the CPS and SPS activation energies of tungsten carbide nanopowders has been analyzed. The CPS activation energies of WC, WC + C and WC + SiC + C nanopowders are shown to be closer to the carbon diffusion activation energy along α-WC grain boundaries. The SPS activation energies of WC and WC + SiC nanopowders turn out to be lower than the carbon grain boundary diffusion activation energy of α-WC.

The consumption of fiber in the human diet is a global recommendation to ensure a healthy diet. Quinoa (Chenopodium quinoa Willd.), a gluten-free grain, and chia (Salvia hispanica), a seed, contain high fiber content and both have the potential to be explored in the development of nutraceutical and pharmaceutical formulations. An interesting characteristic of chia is its ability to form viscous mucilage when in contact with water, bringing the prospect of a binder in solid formulations. To produce tablets with a high fiber content, it is more appropriate to transform the material into granules using a wet process, with the help of a tool that exploits this possibility. Therefore, the objective of the present work was to study, using the Mixer Torque Rheometer, the feasibility of using chia as a binder to produce granulated quinoa and the development of chewable tablets. To this end, an experimental design was carried out to evaluate the impact of variables on the rheometer results for subsequent granulation. It was possible to obtain the granulation point for the formulations and after producing the granules, physical tests were carried out in which we noticed improvements in the flow. In the end, a formulation was selected for the development of chewable tablets containing quinoa and chia fibers.

The polymer binder, poly(imide-co-siloxane) (PIS), was synthesized and applied to form a thin cathode layer composites for a thermal battery that has an unusually high operating temperature of 450 °C. The PIS was prepared through cross-linking of the polyimide with polysiloxane. The morphology of FeS₂/PIS composites showed that FeS₂ particles was coated with the PIS cross-linked gel. The FeS₂/PIS composites enabled to fabricate mechanically stable thin cathode layer that was 20–10% of the thickness of a conventional pellet-type cathode. The FeS₂/PIS composites were stable up to 400 °C and maintained their morphology at this temperature. PIS coating layers decomposed at 450 °C and a new residue was generated, which was observed by transmission electron microscopy and the compositional change was analyzed. The FeS₂/PIS composites showed enhanced thermal stability over that of FeS₂ in thermogravimetric analysis. The thermal battery with the PIS polymer binder showed a 20% discharge capacity increase when compared to a conventional pellet-type cathode.

The present study describes the preparation of a composite material consisting of thermoplastic polyurethane-poly (n-isopropylacrylamide) (TPU-PNIPAM), which was employed for the se-lective adsorption separation of alcohol/water mixed solutions for the first time. The findings revealed that TPU and PNIPAM were interconnected through interchain hydrogen bonding, resulting in exposed hydrophobic isopropyl groups while covering the hydrophilic hydrogen bond sites. Selective separation of alcohols from alcohol/water mixed solutions occurred via London dispersion forces between alkyl groups. Increasing the PNIPAM load on the TPU surface led to a decrease in available hydrogen bond sites capable of bonding with water molecules, an increase in dispersible isopropyl groups interacting with alcohol alkyl groups, and enhanced selective adsorption capacity of TPU-PNIPAM towards alcohol/water mixed solutions. Moreover, TPU-PNIPAM exhibited a characteristic fast-slow-fast-equilibrium ad-sorption curve for different initial concentrations of alcohol/water mixtures, and its selective adsorption capacity increased when temperature reached 55℃. In addition to these general trends, under identical conditions, the selective adsorption capacity of TPU-PNIPAM gradually increased by methanol < ethanol < isopropyl alcohol < propyl alcohol, thus indicating a positive correlation between selectivity performance and hydrophobicity level.

The drug delivery systems receive more and more attention for the control and treatment of many diseases due to their increased number in recent years. The main aims of this study were to develop and to characterize a polyurethane drug delivery system that it is intended to be used for the transmembrane transport of nucleosides. Three different samples have been synthesized based on aliphatic diisocyanates (hexamethylene diisocyanate, isophorone diisocyanate and lysine diisocyanate) as organic phase, respectively a mixture of polyethylene glycol, polycaprolactone diol and low molecular weight diols as aqueous phase. The samples were characterized by pH, refractivity index and solubility measurements, drug loading efficacy and release investigations, thermal behavior, Zetasizer, cells viability and irritation tests on mice skin. The results indicate the obtaining of different populations of neutral acido-basic particles with size between 132 and 190 nm; the Zeta potential values and SEM images show a medium tendency to form clusters, while UV-Vis evaluations indicate an almost 70% encapsulation efficacy, a prolonged release (45% of encapsulated substance is released in the first 5 days) and around 70% of particles have penetrated an artificial membrane in the first 24h. The synthesized products can be tested in further clinical trials, the currently tests on cells culture and mice skin revealing no side effects.

This study propounds a sustainable alternative to petroleum-based polyurethane (PU) foams aiming to curtail this nonrenewable resource's continued and uncontrolled use. Coconut fatty acid distillate (CFAD) and crude glycerol (CG), both wastes from vegetable oil processes, were utilized for bio-based polyol production for rigid PU foam application. The raw materials were subjected to catalyzed glycerolysis with alkaline-alcohol neutralization and bleaching. The resulting polyol possessed properties suitable for rigid foam application with an average OH number of 215 mg KOH/g, acid number of 7.2983 mg KOH/g, and Gardner color value of 18. The polyol was used to prepare rigid PU foam, and its properties were determined using FTIR, TGA/DTA, and UTM. Additionally, the cell foam morphology was investigated by scanning electron microscope (SEM) in which most of its structure revealed an open-celled network and quantified at 92.71% open cell content using pycnometric testing. The PU foam thermal and mechanical analysis results showed an average compressive strength of 70.59 kPa, thermal conductivity of 46.50 mWm-1K-1, and density of 32.79 kgm-3. These properties showed its applicability as thermal insulating foam, thus, demonstrating the potential use of CFAD and CG in commercial polyol and PU foam production.

Background: We aimed to evaluate the effect of early pelvic binder use in emergency management of suspected pelvic trauma, compared with the conventional stepwise approach. Methods: We enrolled trauma patients with initial stabilization using a pelvic binder for suspecting pelvic injury. Inclusion criteria were traumatic injury requiring a trauma team and at least one of the following: loss of consciousness or Glasgow coma score (GCS) < 13; systolic blood pressure < 90 mmHg; falling from ≥6 m; injury to multiple vital organs; and suspected pelvic injury. Various parameters, including gender, age, mechanism of injury, GCS, mortality, hospital stay, initial vital sign, revised trauma score, injury severity score, and outcome, were assessed and compared with historical controls. Results: A total of 204 patients with high-energy multiple-trauma from single level I trauma center in North Taiwan were enrolled in the study from August 2013 to July 2014. The two group baseline patient characteristics were all collected and compared. The trauma patients with suspected pelvic fractures initially stabilized with a pelvic binder had shorter hospital and ICU stays. The study group achieved statistically significantly improved survival and lower mean blood transfusion volume and mortality rate although they were more severe in the trauma score. Conclusions: We recommend prompt pelvic binder use for suspected pelvic injury before definitive imaging is available, as a cervical spine collar is used to protect the cervical spine from further injury prior to definitive identification and characterization of an injury.

Nanofiber (NF) products exhibit outstanding performances in the materials science, textile, and medical fields, which cannot be realized using conventional technologies. However, the safety of such products is debated because of the potential risk of nanomaterials and lack of standardized guidelines for safely evaluating NF products. The global safety evaluations of nanomaterials focused on evaluating the cytotoxicity of zero-dimensional materials including nanoparticles and nanotubes based on OECD criteria. The NFs are one-dimensional materials with nanometer diameters and considerable lengths. Many fibers are applied in a densely woven web-like form, and therefore, assessing cellular penetration and fiber toxicity using the same methods is inappropriate. This study verifies the safety of polyurethane (PU) and polyvinylidene fluoride (PVDF) polymers, which are currently applied in filters and masks. To this end, polymer NFs were collected from each product, and the NFs were compared with reference samples considering their physical properties using FT-IR and Raman spectroscopy. For the safety evaluation, DMSO stocks of varying concentrations of PVDF and PU NFs (at 0.5, 1, 5, and 10 μg/mL) were prepared, and the cytotoxicity and inhibitory effects on nitric oxide production and protein expression obtained via Western blot were identified.

Keywords: artificial bone; conical implants; cylindrical implants; dental implants; implant stability quotient; insertion torque; polyurethane; post-extraction sites; removal torque.

Vaccine hesitancy substantially impacts global vaccination rates. During the COVID-19 pandem-ic in Germany, vaccination uptake exhibited considerable regional disparities. To assess the fac-tors contributing to this variation, we examined the influence of sociodemographic variables on COVID-19, COVID-19 booster, and influenza vaccinations within a cohort of 37,078 participants from 13 German federal states in the digital health cohort study, DigiHero. Our findings re-vealed variations in vaccination rates based on sociodemographic factors. However, these fac-tors had limited explanatory power regarding regional differences in vaccine uptake. In contrast, we found substantial correlations between regional support of specific parties during last local elections and the vaccination uptake at Landkreis-level. In conclusion, sociodemographic factors alone did not suffice to explain the regional disparities in vaccine uptake. Political stances can play a major role, but the current investigation did not assess the individual political orienta-tion, but used only ecological approach.

The blended perfluorinated sulfonic acid ionomers are prepared to have equivalent weight (EW) ~1000, 980, and 830. The catalyst layers (CLs) using blended PFSA ionomers with different side chain lengths and EWs are investigated, compared to the CLs utilizing single ionomers. The IEC results indicate that the blended ionomers have the targeted EWs. As a result, it is found that the blended ionomers exhibit higher ion conductivity than the single ionomers at all temperatures due to higher water uptake of the blended ionomers. Even though they have a similar EW, it implies that the blended ionomers have bulk structure to form competent free volume. The blended ionomers with short side chain (SSC) and low EW can help reduce the activation energy due to the enhanced hydrophobic and hydrophilic segregation. In addition, it is observed that the catalyst layers using the blended ionomer form more porous microstructure to help reduce the resistance of oxygen transport and attributes to lower mass transfer loss. This effect is significantly revealed in the fuel cell operation at not the lower temperature (70 °C) and full humidification (100%) but the elevated temperature (80 °C) and lower relative humidity (50 and 75%). The blended ionomer-based catalyst layers with higher water uptake and porous CL structure result in higher fuel cell performance and better mass transport than the single ionomer-based catalyst layers.

The snATAC + snRNA platform allows epigenomic profiling of open chromatin and gene expression with single-cell resolution. The most critical assay step is to isolate high-quality nuclei to proceed with droplet-base single nuclei isolation and barcoding. With the increasing popularity of multiomic profiling in various fields, there is a need for optimized and reliable nuclei isolation methods, mainly for human tissue samples. Herein we compared different nuclei isolation methods for cell suspensions, such as peripheral blood mononuclear cells (PBMC, n=18) and a solid tumor type, ovarian cancer (OC) (n=18), derived from debulking surgery. Nuclei morphology and sequencing output parameters were used to evaluate the quality of preparation. Our results show that NP-40 detergent-based nuclei isolation yields better sequencing results than collagenase tissue dissociation for OC, significantly impacting cell identification and analysis. Given the utility of applying such techniques to frozen samples, we also tested frozen preparation and digestion (n=6). A paired comparison between frozen and fresh samples validated the quality of both specimens. Finally, we demonstrate the reproducibility of scRNA and snATAC + snRNA platform, by comparing the gene expression profiling of PBMC. Our results highlight how the choice of nuclei isolation methods is critical for obtaining quality data in multiomic assays. It also shows that the measurement of expression between scRNA and snRNA is comparable and effective for cell type identification.

Emulsion stabilisation of base layers surfaced with chip seals often proves problematic with chips punching into the base and early distress. This can be aggravated by the use of modified binders that restricts the evaporation of moisture from pavement layers. The introduction of New-age (Nano) Modified Emulsion (NME) stabilisation has the advantage that water is chemically repelled from the stabilised layer resulting in an accelerated development of strength. A need was identified to evaluate the early life performance of selected chip seals, together with identified binders. Three different chip seal surfacings with unconventional modified binders were constructed and evaluated using Accelerated Pavement Testing (APT) with the MMLS3. The objectives of the experimental design and testing were to evaluate binder performance, early loss of chips before chip orientation at low temperatures, punching of the chips into the NME stabilised base, deformation characteristics of a Cape seal and the effect of the use of a standard normal modified binder. This paper contains details of the NME base layer, the binder and seal selection and the test results. It is shown that a cost-effective thin chip seal in combination with a suitable binder can be used on a NME stabilised base with confidence.

The aim of performed studies was to fabricate an antibacterial and degradable scaffold that may be used in the field of skin regeneration. To reach the degradation criterion the biocompatible polyurethane (PUR), obtained by using amorphous macrodiol α,ω-dihydroxy(ethylene-butylene adipate) macrodiol (PEBA), was used and processed with so-called “fast-degradable” polymer polylactide (PLA) (5 wt% or 10 wt%). To meet the antibacterial requirement obtained hybrid PUR-PLA scaffolds (HPPS) were modified with ciprofloxacin (Cipro) (2 wt% or 5 wt%), the fluoroquinolone antibiotic inhibiting growth of bacteria such as Pseudomonas aeruginosa, Escherichia Coli and Staphylococcus aureus, which are main cause of wound infections. Obtained unmodified and Cipro-modified HPPS were studied towards their chemical composition to detect presence or absence of characteristic functional groups of PUR, PLA and Cipro, and as well to indicate the participation of hydrogen bonds in the HPPS structure in dependence on PLA addition and ciprofloxacin modification. Mechanical properties were studied to determine the possible application of HPPS as a skin tissue scaffold. Scanning electron microscopy (SEM) was used to study morphology of unmodified and Cipro-modified HPPS and to performed elementary analysis by using energy-dispersive x-ray spectroscopy (EDX) of obtained materials. Finally, the microbiological tests were performed to indicate the antibacterial effect of Cipro-modified HPPS on S.aureus growth. Performed studies showed that Cipro-modified HPPS, obtained by using 5 % of PLA, possess suitable mechanical characteristic, morphology, degradation rate and demanded antimicrobial properties to be further developed as a potential scaffolds for skin tissue engineering.

People wore clothes for warmth, survival and necessity in modern life as well but in modern era, eco-friendliness, shorten production time, design, and intelligence also matters. The seamless bonding technology strengthen the bond between fabrics in textiles, while Grey relational analysis (GRA) can be applied to fabrics to measure the relationship between data series and determine the closeness of each data series. In this study, polyurethane prepolymer, 2-Hydroxyethyl acrylate (2-HEA) as an end-capping agent, and n-octyl acrylate (ODA) as a photo-initiator were used to synthesize dual-curing polyurethane hot-melt adhesive. The Taguchi quality engineering and grey relational analysis used to discuss the influence of different mole ratio of NCO:OH, and the effect of the molar ratio of addition of octyl decyl acrylate on the mechanical strength. The Fourier transform infrared spectroscopy (FTIR) results showed the termination of prepolymer's polymerization reaction and the C=O peak intensity at 1730 cm-1 indicating the efficient bonding to main chain. The high molecular weight polymer (20,000-30,000) described by advanced polymer chromatography (APC) confirmed the polyurethane polymer bonded with octyl decyl acrylate to achieve the photo-thermosetting effect. The thermogravimetric analysis (TGA) results showed the thermal decomposition temperature of polyurethane hot melt adhesive also increased and highest pyrolysis temperature (349.89℃) for the polyhydric alcohols. The high value of shear strength (34.94 kg/cm2) as well as peel strength (1.68 kg/cm) were also observed in dual-cure photo-thermosetting polyurethane hot melt adhesive. The signal-to-noise ratio also used to generate the grey relational degree. It was observed that the best parameter ration of NCO: OH was 4:1 with 5 moles of monomer. The Taguchi quality engineering method was used to find the parameters of single quality optimization, and then the grey relation calculation was used to obtain the parameter combination of multi-quality optimization for thermosetting polyurethane hot melt adhesive. The study aims to meet the requirements of seamless bonding in textile factories and optimized experimental parameter design by setting target values can effectively increase production speed, reduce processing time and costs as well.

This study presents a novel polyurethane-activated carbon composite (PACC) as an effective and sustainable adsorbent for treating lead-ion-contaminated waters. The PACC was characterized using SEM-EDX, FTIR, BET, XRD, and TGA to evaluate its physicochemical and thermal properties. Furthermore, the PACC was employed in an experimental column adsorption setup to investigate its adsorption performance and to develop a dynamic method suitable for industrial implementation. Parameters such as bed height (50, 100, 150 mm), flow rate (4, 6, 8 mL min-1), pH (2, 4, 6), and initial metal ion concentrations (10, 50, 100 mg L-1) were examined. The experimental data exhibited strong agreement with the Thomas and Yoon-Nelson models (R2 ≥ 0.96), indicating efficient adsorption mechanisms. Remarkably, the depleted adsorbent has the potential for facile regeneration without substantial loss in capacity. The PACC demonstrated excellent adsorption performance for lead ions in aqueous solutions in a fixed-bed column system. Thus, the novel PACC material holds potential for scalable application in industrial settings to address water pollution challenges, especially in regions with uncontrolled effluent discharge.

Reactive energetic plasticizers (REPs) coupled with hydroxy-telechelic poly(glycidyl azide-co-tetrahydrofuran) (PGT)-based energetic polyurethane (PU) binders for use in solid propellants and plastic-bonded explosives (PBXs) were investigated. The generation of gem-dinitro REPs along with a terminal alkyne stemmed from a series of finely designed approaches to not only satisfy the common demands as conventional energetic plasticizers but prevent the migration of plasticizers. The miscibility and rheological behavior of a binary mixture of PGT/REP with various REP fractions were quantitatively determined by differential scanning calorimetry (DSC) and rheometer, respectively, highlighting the promising performance of REPs in the formulation process. The kinetics on the distinct reactivity of propargyl vs. 3-butynyl species of REPs towards the azide group of the PGT prepolymer in terms of Cu-free azide-alkyne 1,3-dipolar cycloaddition (1,3-DPCA) was studied by monitoring 1H nuclear magnetic resonance spectroscopy and analyzing the activation energies (Ea) obtained using DSC. The thermal stability of the finally cured energetic binders with the incorporation of REPs indicated that the thermal stability of the REP/PGT-based PUs was maintained independently of the REP content. The tensile strength and modulus of the PUs increased with increasing the REP content. In addition, the energetic performance and sensitivity of REP and REP triazole species was predicted.

The paper focuses on the application of a multilevel, integrative and territorial approach to the protection of cultural heritage through planning instruments in Serbia. It points out the problems of the sectoral approach and discusses international recommendations that can be integrated into the planning methodology. The case study is the area of Djerdap National Park, which has an already established international and national importance. The research suggests that the cultural heritage in the area, with the exception of the Roman limes, is still recognized at the level of individual localities. The study emphasizes the importance of aligning all levels of governance to safeguard the whole spatial entity rather than focusing solely on its particular areas. The interna-tional and national importance of the planning area contributes to the strengthening of awareness of heritage and its institutional protection. However, the vitality of the area, which is key to its sustainable development, comes from the local level. Planning documents contribute to the inte-gration of local values and local communities into development programs and projects.

Glycosidic linkage analysis was conducted on the unfractionated polysaccharides in the alcohol-insoluble residues (AIRs) prepared from six red seaweeds (Gracilariopsis sp., Prionitis sp., Mastocarpus papillatus, Callophyllis sp., Mazzaella splendens, and Palmaria palmata) using GC-MS/FID analysis of partially methylated alditol acetates (PMAAs). The cell walls of P. palmata primarily contained mixed-linkage xylans and small amounts of sulfated galactans and cellulose. In contrast, the unfractionated polysaccharides of the other five species were rich in galactans displaying diverse 3,6-anhydro-galactose and galactose linkages with varied sulfation patterns. Different levels of cellulose were also observed. This glycosidic linkage method offers advantages for cellulose analysis over traditional monosaccharide analysis that is known for underrepresenting glucose in crystalline cellulose. Relative linkage compositions calculated from GC-MS and GC-FID measurements showed that anhydro sugar linkages generated more response in the latter detection method. This improved linkage workflow presents a useful tool for studying polysaccharide structural variations across red seaweed species. Furthermore, for the first time, relative linkage compositions from GC-MS and GC-FID measurements, along with normalized FID and total ion current (TIC) chromatograms without peak assignments, were analyzed using principal component analysis (PCA) as a proof-of-concept demonstration of the technique's potential to differentiate various red seaweed species.

Background: Educating college students about the importance of good sleep habits could lead to the adoption of healthier sleep routines, including sufficient sleep duration and sleep quality. The current pre-post study examines the impact of completing a sleep education program called “Sleep 101” on (1) sleep hygiene practices, (2) sleep quality, and (3) weekday and weekend sleep behaviors among college students. “Sleep 101” is an interactive online course developed to educate college students about the importance of sleep by addressing basic sleep physiology, the impact of sleep on mood, academic and physical performance, the interactions between sleep and various substances, and common sleep disorders. Methods: 338 college students were recruited from a midsized public university in the US and invited to participate in “Sleep 101”, of which 25 participants completed the baseline and post-intervention questionnaire. The Sleep Hygiene Index (SHI) was utilized to evaluate sleep hygiene practices, while standard questions were employed to assess weekday and weekend sleep behaviors and overall sleep quality. Results: Those who completed the study demonstrated a significant increase in weekday sleep duration and were less likely to engage in negative prior bedtime activities. In addition, 40% of those who completed baseline and post-intervention assessments noticed improvements in their sleep quality. Conclusion: These findings suggest that a brief online program is beneficial in improving sleep behaviors among college and could be a scalable approach to addressing current sleep issues and preventing future sleep problems in college students.

The profile of secondary metabolites occurring in apple cuticular layer is not only characteristic for particular apple cultivar, but also dynamically reflects various external factors in growing environment. In this study, the possibility to authenticate apple samples based on analysis of their cuticular layer extracts was investigated. Ultra-high-performance liquid chromatography coupled to high resolution tandem mass spectrometry (UHPLC-HRMS/MS) was employed for obtaining metabolomic fingerprints. In total, 274 authentic apple samples, four cultivars harvested within the seasons 2020 to 2022 in the Czech Republic and Poland were analysed. The generated complex data processed by univariate and multivariate statistical methods enabled to build classification models for discrimination of apple cultivars as well as their geographical origin. The models showed very good performance in differentiation of Czech and Polish samples for three of four cultivars: ‘Gala’, ‘Golden Delicious’ and ‘Idared’, moreover, the validity of the models was verified over harvest seasons. The diagnostic markers, besides metabolites of triterpene biosynthetic pathway, mainly represented wax esters. ‘Jonagold’, which is known to be susceptible to mutations, was the only cultivar for which the unambiguous classification of geographical origin was not possible.

Strawberry root rot caused by Neopestalotiopsis clavispora is one of the main diseases of strawberry and significantly impacts the yield and quality of strawberry fruit. There are now no effective control techniques available except for fungicide sprays, which may directly impact consumers. Biological control is becoming an alternative method for the control of plant diseases to replace or decrease the application of traditional synthetic chemical fungicides. Trichoderma is widely used as a biological agent for controlling strawberry root rot. In order to provide resources for screening the highly effective biocontrol fungus for controlling strawberry root rot caused by Neopestalotiopsis clavispora, the biocontrol mechanism,the control effects of Trichoderma asperellum CMT10 against strawberry root rot and growth-promoting effects on strawberry seedlings were investigated by plate culture, microscopy observation and root drenching methods.The results showed that CMT10 had obvious competitive, antibiotic and hyperparasitism effects on Neopestalotiopsis clavispora CMGF3. The CMT10 could quickly occupy nutritional space, and the inhibition rates of CMT10 against CMGF3 in confrontation culture on 7 d was 65.49%. The inhibition rates of volatile metabolite and fermentation metabolite produced by CMT10 against CMGF3 were 79.67% and 69.84%, respectively. The mycelium of strain CMT10 can act as hyperparasites by making contacting, winding and penetrating hyphae of CMGF3. Pot experiment showed that the biocontrol efficacy of CMT10 on strawberry root rot caused by Neopestalotiopsis clavispora was 63.00%. CMT10 had obvious promotion effect on strawberry growth, the plant height, root length, total fresh weight, root fresh weight, stem fresh weight and root dry weight, with the promotion rates were 20.09%, 22.39%, 87.11%, 101.58%, 79.82% and 72.33%, respectively. Overall, this study showed the ability of Trichoderma asperellum CMT10 to control strawberry root rot and their potential to develop as novel biocontrol agents to replace chemical fungicides for eco-friendly, sustainable agriculture.

Apis mellifera, especially weak ones, are highly vulnerable to Carpoglyphus lactis mites, which can rapidly infest and consume stored pollen, leading to weakened colonies and potentially colony collapse. This study aimed to ascertain and investigate the prevalence of this mite in honeybee colonies across 9 provinces in the Republic of Korea (ROK). A total of 615 honeybee colonies were collected, from 66 apiaries during the spring and 58 apiaries during the summer of 2023. A 1,242 bp segment of the the Cytochrome c oxidase subunit 1 (COI) gene was amplified using the polymerase chain reaction method. The detection levels of C. lactis in the honeybees were compared between winter and summer. Based on the COI sequence analysis, the nucleotide sequence similarity of C. lactis mites isolated in the ROK with those from China (NC048990.1) was found to be 99.5%, and with those from the United Kingdom (KY922482.1) was 99.3%. This study is the first report of C. lactis in Korean apiaries. The findings in this study demonstrate a significantly higher detection rate in winter, which is 4.1 times greater than that in summer (p &lt; 0.001). Furthermore, the results underscore the usefulness of molecular diagnostic techniques for detecting C. lactis mites.

COX II containing a dual core CuA active site is one of the three core subunits of mitochondrial Cco, which plays a significant role in the physiological process. In this report, the full-length cDNA of COXⅡ gene was cloned from Sitophilus zeamais, which had an ORF of 684 bp encoding 227 amino acids residues. The predicted COXⅡ protein had a molecular mass of 26.2 kDa with pI value of 6.37, and multiple sequence alignment and phylogenetic analysis indicated that Sitophilus zeamais COXⅡ had high sequence identity 78.51% with the COXⅡ of other insect species, especially similarity to sitophilus oryzae. This gene was subcloned into the prokaryotic expression vector pET-32a, and induced by IPTG in E.coli Transetta (DE3) expression system. Finally the COXⅡ with 6-His tag was purified using affinity chromatography with Ni²⁺-NTA agarose. WB showed the recombinant COXⅡ was about 44 kD, and the concentration of fusion protein was 50μg/mL. UV-spectrophotometer and infrared spectrometer analysis showed that recombinant COXⅡ could catalyze the oxidation of substrate Cytc, and influenced by AITC. It was found that AITC could form a hydrophobic region with COXⅡ protein via molecular docking, besides, a sulfur atom of AITC structure could form a length of 2.9 Å hydrogen bond with Leu-31. These results will provide valuable information for elucidating the role of COXⅡ in Sitophilus zeamais responses to AITC, meanwhile, it will helpful to carry out a point mutation in AITC binding sites for the future research.

The properties of the annual, semiannual and triennial oscillations (AO, SAO and TO) in the middle atmosphere have been investigated using the TIMED/SABER temperature data. The Lomb-Scargle and wavelet spectra were used to determine the dominant oscillations in the background temperature field. The AO is prominent at the mid-latitudes. The AO amplitudes present an asymmetry between the two Hemispheres, being larger in the mesosphere than in the stratosphere. The SAO dominates the tropical regions, with three amplitude maxima at altitudes of 45, 75, and 85 km. The SAOs in the upper mesosphere (75 km) are out of phase with those in the mesopause (85 km) in the tropical regions, which can generate an enhancement of 11 K at each equinox, contributing to the lower mesospheric inversion layer. The TO is significant in the tropical region, with amplitude being maximum at 35, 45 and 85 km. Result shows that there may be potential interaction by the TO with SAO at 85km at the equator. The relation between ENSO and TO has also been discussed. The ENSO signal may modulate the amplitude of the TO, mainly in the lower stratosphere. The real origin of the TO may lie in the wave-mean-flow interaction.

This paper is focused on typical rural settlements in the Stara Planina Mountain area in Serbia. They are distinguished by their authenticity, identity and character, and they have still not been destroyed by inappropriate development as is the case in some other mountain areas in Serbia, where the effects of urbanization, globalization and homogenization are obvious. Consequently, there is a need to prevent these effects in mountain areas where there is a threat of disbalance between development and the inherited natural and cultural values. The paper starts from several important concepts that relate contemporary approaches to cultural heritage preservation, place morphology and planning future development. The concept definitions from recent documents from related fields are used. These concepts are then applied to the area of Stara Planina Mountain and its rural settlements. The necessity for an integrative approach to planning this area with significant natural and anthropogenic potential is pointed out, including its integration into international programs of sustainable development.

The research reported on this paper was aimed at improving the overall efficiency of a PDO certified artisanal cheese production process. Being a PDO certified foodstuff by the EU, it is considered to have properties and qualities determined by the geographical environment in which is made, with its production taking place in a specific and determined geographical location, in this case the Serra da Estrela region. In that sense, the authors conducted a mapping according to a systemic perspective of the processes involved in the context of manufacturing and distribution of certified Serra da Estrela cheese. Numerous methods were used throughout the process, such as a systemic design analysis, and techniques derived from ethnographic methods, which led to the collection of data in the field and consequently provided the immersion of the researcher in genuine work situations. Critical points were identified and emphasized in the systemic map with the purpose of encouraging initiatives to address and overcome the gaps and inefficiencies detected. The systemic design analysis triggered the development of design work. Observations following an ethnographic approach identified ergonomic risks in cheese making during the process of cutting excess chips, fostering the emergence of musculoskeletal disorders at the wrist. A tool that fits best to the task at hand was developed. A prototype of the new tool enabled collecting feedback from use in the work context, in order to inform product development. The domains of agricultural production and microbiology, considering the specific microorganisms developed trough the ripening process of the cheese, turned out to be aspects of high importance for the issue under focus, contributing to a broader understanding of the ripening process and its risks, simultaneously improving the efficiency and success of cheese production. If it were not for the systemic analysis, which served as a link between the boundaries of distinct domains such as the risk of microorganism contamination, ergonomics, energy efficiency, legislation and regulation policies, transportation challenges and economic viability, approached throughout the research. Simultaneously creating bridges between them, the various problems might not have been detected in the first place, as they are usually addressed in specialized disciplines, predetermined by the restrictions of each specific area of knowledge. As a consequence of the development of this research, which was based on an analysis that sought to establish possible connections between various disciplines and tried to constantly maintain a holistic perspective, making new connections and observing the issues from a new angle, apart from the already established methodologies. All this allowed to lay out the seeds for the development of a plan to tackle the critical points identified by the systemic analysis reported in this paper.

Promoting green development has become an important way to optimize the ecological and economic structure and promote sustainable development. The Yangtze River Economic Belt is an important economic corridor in China, and it remains to be examined whether the implementation of environmental regulations has enhanced the green total factor productivity (GTFP) of cities. This paper calculates the green total factor productivity of 107 cities within the Yangtze River Economic Belt by using the super-efficient SBM model and the GML index with Chinese city panel data from 2007-2019 and measures the intensity of environmental regulations through textual analysis. The bidirectional fixed-effects model constructed in this paper suggests an inverted U-shaped relationship between environmental regulation and GTFP, which is confirmed by a series of robustness tests. Green technology innovation and advanced industrial structure play a mechanism role in this. In regions with lower levels of green technology and industrial structure, the inverted U-shaped relationship between environmental regulation and green total factor productivity is more significant. In addition, the phenomenon of GTFP rising and then falling because of environmental regulation is more obvious in cities in the middle and upper reaches of the Yangtze River and outside the urban agglomerations. Therefore, when formulating environmental regulation policies, it is necessary to balance the relationship between economic development and environmental protection and harmonize the environment and economic development of the entire Yangtze River Basin.

The wetlands in northeastern Bangladesh are home to some of the most prolific and valuable ecosystems on the planet, offering a wide range of benefits to both the local and wider communities. A limited number of research on this topic have been carried out in various wetlands in coastal hilsa, but none have been located in the northeastern region of Bangladesh. Thus, the goal of this study was to better understand the most commercially relevant species (anadromous hilsa) in northeastern Bangladesh as well as to assess the wetland ecosystem services more thoroughly with the contribution of their fish genetic resources. In addition to laboratory studies, fieldwork was done in the fishing settlements along the Surma River, Hakaluki Haor, and Tanguar Haor. The study classified 77 fish species into 21 subcategories of ecosystem services, of which 56% were not threatened, 17% were vulnerable, and 10% were highly endangered. The species Hilsa was found to be the most economically significant, accounting for 1% of the GDP overall. The study determined if the hilsa stock of the examined wetlands maintains a single or several subpopulations in comparison to other parts of the country when they migrate from saline water to northeastern Bangladesh (freshwater). But when compared to other groups, the FST score was between 0.000 to 0.017, indicating that the populations are identical and that there is genetic material sharing between them. Additionally, these statistics imply that the Sylhet haor and adjacent river systems contain a single stock of Hilsa fish. Nevertheless, a number of stresses and risks, including overexploitation, illicit and destructive fishing, siltation, and natural disasters like flash floods, have been linked to changes in the supply of hilsa and other ecosystem services. This study also emphasizes the necessity of policy attention and research to address the concerns.

In this paper, we introduce a specialized, fully automated experimental arrangement designed for assessing the effectiveness of augmented and virtual reality technologies in healthcare setting and explore its design principles focusing on depth sensor characterization. The main goal of this project is to establish a robust benchtop platform for the quantitative evaluation of extended reality technologies in a controlled environment, emphasizing the practical assessment of augmented reality head-mounted devices. We outline a design concept and considerations for an experimental configuration aimed at creating a realistic testing environment. This apparatus comprises an observation platform mounted on a three-degree-of-freedom motorized system and a test phantom stage. Focusing on real-case scenarios, we utilized a range of sensors, including readily available range-sensing cameras and commercial augmented reality headsets, such as the Intel RealSense L515 LiDAR camera, mounted on the motion control system. The setup enabled automated data collection and facilitates controlled assessments and validation of various facets of augmented reality technologies, including object, hand, and head tracking, as well as static and dynamic image registration. This paper describes the system architecture, the process of automated data collection, and presents several evaluation studies conducted with this setup, providing insights into the quality and temporal noise associated with static or moving objects or observers in augmented reality applications.

To conduct high-precision and high-resolution numerical simulation of complex flow structures in turbomachinery, a high-order finite volume weighted essentially non-oscillatory (WENO) scheme for the large eddy simulation (LES) is improved and embedded into the three-dimensional viscous unsteady CFD solver NUAA-Turbo. Firstly, the spectral characteristics and unsteady convergence of the improved WENO scheme are studied. Compared with the classical WENO scheme, the improved WENO scheme has better dissipation and dispersion characteristics and faster convergence speed. Then, the coefficient CW of the Wall-Adapting Local Eddy-viscosity (WALE) model is calibrated by decaying homogeneous isotropic turbulence (DHIT) test case. Finally, the scheme is applied to conduct high-precision LES calculations of turbulent boundary layer flow, supersonic compression corner flow, and low-pressure turbine cascade separation flow. The numerical simulation results show that this WENO scheme has excellent shock wave capture ability and turbulence resolution and can capture more flow field details with less mesh size, greatly reducing the computational cost and laying a foundation for large-scale engineering application of LES.

To secure logic circuits against the illegal copying the insertion of the so-called key bit inputs using XOR/XNOR gates has been proposed in . The inserted gates modify (lock) the behavior of the original circuit and only the correct choice of the secret key bits guarantees the equivalent behaviour of the locked circuit to the original circuit. To break this kind of security, i.e. to find the secret key bits, there was a SAT solver based attack proposed in . The aim of this work is to experimentally verify this attack on several locked circuits with various number of primary inputs and outputs and with various number of gates. Except for the random placement of the key gates we evaluate also the positioning with chaining elimination. The obtained and presented results show that we were able to unlock 10 of 11 circuits within few minutes on a common PC.

Intermetallic compounds are increasingly being expected to utilize in tribological environments, but to date the works are hindered by insufficient ductility at low and medium temperature. This paper presents a novel multiphase intermetallic alloy with the chemical composition of Mo-40Ni-13Si (at.%). Microstructure characterization reveals that a certain amount of ductile Mo phases formed during the solidification process of ternary Mo-Ni-Si alloy melt, which is undoubtedly beneficial to the ductility improvement of intermetallic alloy. Tribological properties of the designed alloy, including wear resistance, friction coefficient and metallic tribological compatibility, were evaluated under dry sliding wear test conditions at room temperature. Results suggested that the multiphase alloy possesses an excellent property for room-temperature wear applications, which is attributed to the unique microstructural features and thereby good combination in hardness and ductility. The corresponding wear mechanism is also reported by observing the worn surface, subsurface and wear debris of alloy, which to be found is soft abrasive wear.

With the integrated development of the Internet, wireless sensor technology, cloud computing, and mobile Internet, there has been a lot of attention given to research about and applications of the Internet of Things. A Wireless Sensor Network (WSN) is one of the important information technologies in the Internet of Things; it integrates multi-technology to detect and gather information in a network environment by mutual cooperation, using a variety of methods to process and analyze data, implement awareness, and perform tests. This paper mainly researches the localization algorithm of sensor nodes in a wireless sensor network. Firstly, a multi-granularity region partition is proposed to divide the location region. In the range-based method, the RSSI (Received Signal Strength indicator, RSSI) is used to estimate distance. The optimal RSSI value is computed by the Gaussian fitting method. Furthermore, a Voronoi diagram is characterized by the use of dividing region. Rach anchor node is regarded as the center of each region; the whole position region is divided into several regions and the sub-region of neighboring nodes is combined into triangles while the unknown node is locked in the ultimate area. Secondly, the multi-granularity regional division and Lagrange multiplier method are used to calculate the final coordinates. Because nodes are influenced by many factors in the practical application, two kinds of positioning methods are designed: the unknown node is in the positioning unit or not. When the unknown node is on the side of the positioning unit, we use the method of vector similarity. Moreover, we use the centroid algorithm to calculate the ultimate coordinates of unknown node. When the unknown node is not on the side of the positioning unit, we establish a Lagrange equation containing the constraint condition to calculate the first coordinates. Furthermore, we use the Taylor expansion formula to correct the coordinates of the unknown node. In addition, this localization method has been validated by establishing the real environment.

The electroencephalogram (EEG) is a record of brain activity. Brain Computer Interface (BCI) technology formed by the EEG signal has become one of the hotspots at present. How to extract the feature signal of EEG is the most basic research of BCI technology. In this paper, A new method of recognizing fatigue, conscious, concentrated state of human brain is proposed by the combination of discrete wavelet transform and the neural network based on EEG signal. First of all, the law signal is preprocessed by the wavelet denoising method because the law EEG signal contains a large number of high frequency noise, which is decomposed into multi-layer high frequency signal and low frequency signal. thus, δ wave, θ wave, α wave, β wave are obtained by the wavelet transform. And then, frequency band energy of the different wave is regards as the feature signal of EEG. In the experiment, the feature signal is classified by radial basic function (RBF) and annealed chaotic competitive learning network (ACCLN). RBF and ACCLN networks are trained with 500 sets of sample data and are tested by 100 sets of samples in different mental states. The experimental results show that the average accuracy of RBF network under three conditions are 88.75%, 88.25%, 88.5%, respectively, and the correct rate of ACCLN network is 97%, 98%, 98%, respectively.

Early discharge after childbirth has led to a rise in neonatal readmission, becoming a major concern in recent decades. Our research aimed to identify the risk factors and incidence of neonatal readmission, as well as explore preventive measures. Our study at the Clinical Hospital of Pediatrics in Ploiești, Romania included 108 neonates admitted during the neonatal period. This accounted for 2.06% of all admissions (5226). The most prevalent cases were malnutrition (25%), fever (20.3%) and bronchiolitis (17.5%). Diarrhea and infectious gastroenteritis were also observed (14.8%), along with acute rhinoconjunctivitis (9.2%) and late onset sepsis (3.7%). No deaths were recorded. The most significant characteristics identified were number of children (p&lt;0.001) and age at maternity discharge (p&lt;0.001). By following the prevention rules, malnutrition, feeding errors, and infections can be avoided. This includes practicing proper hand hygiene for both mothers and medical staff, as well as educating and demonstrating to mothers the benefits of breastfeeding. In addition, all newborns discharged from the maternity ward should benefit from follow-up at 7-10 days of life. Our results confirm the effectiveness of a multidisciplinary team and endorse promoting breastfeeding. Implementing quality control measures and regularly evaluating the surveillance program will help improve its effectiveness.

Wearable technology has been proposed as a potential tool to change the way of human life, such as the smart bracelet and the Google Glass. In the wearable technology, the inertial sensor has great significance in tracking the object movements. The paper focused on detecting the movements of user’s finger based on the inertial sensor to give the control signals. Firstly, the attitude matrix, which represented the transformation relation of carrier coordinate system and the navigation coordinate system, was obtained. Secondly, the attitude matrix was expressed based on the quaternions. Thirdly, the finger gesture was processed by the attitude matrix to get the attitude angle. Finally, the robot was controlled by attitude angle to make the moving action. The experimental results showed the detection of the finger movement is effective.

Two interesting compounds such as quaternary ammonium lignin(QAL) and 2-ethylhexyl phosphoric acid mono-2-ethylhexyl ester (P507) were synthesized as ionic liquids(QP-ILs) for the extraction of metal ions. The extraction behavior of Co(II) and Ni(II) from chloride solution was compared between QP-ILs and P507. The results showed that the extraction rates of Co(II) and Ni(II) in the two solutions varied with the extraction conditions, but QP-ILs has stronger extractability for cobalt than P507, while Ni is on the contrary. Under the same conditions, the Co/Ni separation performance(βCo/Ni) in QP-ILs is superior to that in p507. At pH4.0, 55℃, concentration of 20%, extraction time of 10 minutes, the βCo/Ni of QP-ILs reached to 2703, while that of P507 was only 164. In conclusion, QP-ILs was more efficient than P507 for separating Co from mixed solutions.