The increasing regulatory pressure to monitor and reduce GHG emissions and air pollutants requires cost-effective methods for their surveillance. The most common technique used for scientific investigations on gas concentration monitoring in barns are accurate but expensive and with a complex maintenance. This research study analysed the potential use of a low-cost portable measurement devices for the measurement of ammonia (NH3) and carbon dioxide (CO2) concentrations in an open dairy barn. A comparison between gas concentrations acquired at different heights from the floor by using portable devices and those acquired by a photoacoustic infrared multigas spectroscope (i.e., reference measurement) in the same sampling locations was carried out to determine the precision of the low-cost portable devices. The performance of low-cost portable devices was statistically analysed by the application of the one-way analysis of variance, correlation analysis and regression analysis. The results showed a significant difference between gas concentration values at various heights from the floor for both NH3 and CO2. The correlations between concentrations acquired by the low-cost portable device and the INNOVA were statistically significant (r=0.83; P<0.001) for gas concentrations monitored at 0.4 m from the floor. Compared with the reference measurement device, the low-cost devices were effective in the monitoring of NH3 concentrations at 0.40 m from the floor though it underestimated them in the barn at increasing of the height from the floor, whereas the device was not adequate for CO2 concentrations. In detail, the relative measurement error of the low-cost devices compared to INNOVA was reduced close to the floor during NH3 concentration measurements. Within these limitations, this device could be useful for monitoring NH3 concentration in the barn and to assess variation in NH3 concentrations mainly related to the animal occupied zone. Further efforts are needed in this field of research to identify low-cost device that could simplify emission estimation from open dairy barns.

Achieving the thermal conductivity required for efficient heat management in semiconductors and other devices requires the integration of thermally conductive ceramic fillers at concentrations of 60 vol% or higher. However, the increased filler content often negatively affects the mechanical properties of the composite matrix, limiting its practical applicability. To address this issue, in this paper, we present a new strategy to reduce the required ceramic filler content: the use of a thermally conductive ceramic composite filler with carbon nanotubes (CNT) grown on aluminum nitride (AlN). We have combined catalyst coating technology with vacuum filtration to ensure that the catalyst is uniformly applied to micrometer-sized AlN particles, followed by efficient and uniform synthesis of CNTs using a water-assisted process in a vertical furnace. By carefully controlling the number of vacuum filtration cycles and the growth time of the CNTs, we demonstrate precise control over the number and length of the CNT layers, thereby adjusting the properties of the composite to the intended specifications. When AlN/CNT hybrid fillers are incorporated into silicone rubber, while maintaining the mechanical properties of rubber, the thermal diffusivity achieved at reduced filler levels exceeds that of composites using AlN-only or simultaneous AlN and CNTs formulations. This demonstrates the critical role of CNTs on AlN surfaces. Our study represents a significant advancement in the design of thermally conductive materials with potential implications for a wide range of applications.

Most methods for measuring environmental lead (Pb) content are time consuming, expensive, hazardous, and restricted to specific analytical systems. To provide a facile, safe tool to detect Pb, we created pMet-lead, a portable fluorescence resonance energy transfer (FRET)-based Pb biosensor. pMet-lead comprises a 3D-printed frame housing a 405-nm laser diode — an excitation source for fluorescence emission images (YFP and CFP) — accompanied by optical filters, a customized sample holder with a Met-lead 1.44 M1 (the most recent version)-embedded biochip, and an optical lens aligned for smartphone compatibility. Measuring the emission ratios (Y/C) of the FRET component enables Pb detection with a dynamic range of nearly 2 (1.96), pMet-lead/Pb dissociation constant (K_d) 45.62 nM, and limit of detection 40 nM (0.832 μg/dL, 8.32 ppb). To mitigate earlier problems with lack of selectivity for Pb vs. zinc, we preincubated samples with tricine, a low-affinity zinc chelator. We validated pMet-lead measurements of characterized laboratory samples and unknown samples from six regions in Taiwan by inductively coupled plasma mass spectrometry (ICP-MS). Notably, two unknowns had Y/C ratios significantly higher than that of the control (3.48 ± 0.08 and 3.74 ± 0.12 vs. 2.79 ± 0.02), along with Pb concentrations (10.6 ppb and 15.24 ppb) above the WHO-permitted level of 10 ppb in tap water, while the rest four unknowns showing no detectable Pb upon ICP-MS. These results demonstrate that pMet-lead provides a rapid, sensitive means for on-site Pb detection in water from the environment and in living/drinking supply systems to prevent potential Pb poisoning.

This paper reports the design, development, and testing of a novel, yet simple and low-cost portable device for the rapid detection of SARS-CoV-2. The device performs loop mediated isothermal amplification (LAMP) and provides visually distinguishable images of the fluorescence emitted from the samples. The device utilises an aluminium block embedded with a cartridge heater for isothermal heating of the sample and a single-board computer and camera for fluorescence detection. The device demonstrates promising results within 20 minutes using clinically relevant starting concentrations of the synthetic template. Time-to-signal data for this device are considerably lower compared to standard qPCR machine (~10-20 minutes vs >38 minutes) for 1×105 starting template copy number. The device in its fully optimized and characterized state can potentially be used as simple to operate, rapid, sensitive, and inexpensive platform for population screening as well as point-of-need SARS-CoV-2 detection and patient management.

Great toe strength (GTS) weakness is linked to declines in balance and mobility. Assessing GTS, particularly great toe extension strength (GTES) accurately is often neglected in clinical evaluations due to cumbersome and subjective methods. This study aims to characterize the force development curve output from the ToeScale and examine GTES variations with age, sex, BMI, and grip strength (GS) using traditional analyses and machine learning (ML). We conducted a pilot, cross-sectional feasibility study with convenience samples. We assessed GS using a hand-grip dynamometer and GTES using the ToeScale. Data analysis included descriptive statistics, correlations, independent samples t-tests, and accuracy and area under the curve (AUC) scores for three ML models. Thirty-one participants (Males: 9, Females: 22), 14 young (18-24 years), and 17 older (>65 years) adults participated in the study. Males had significantly higher peak GTES than females in both age groups. Associations between GTES parameters with BMI and GS varied by age and sex. ML model accuracies and AUC scores were low-moderate but aligned with traditional analyses. Future studies with larger samples and optimized ML models are needed.

A portable laser photoacoustic sensor based on a Field-Programmable Gate Array (FPGA) is reported for methane detection. A tunable DFB diode laser in the 1654 nm wavelength range is used as an excitation source. The photoacoustic signal processing was implemented by a FPGA device. A small resonant photoacoustic cell is designed. The minimum detection limit (1σ) of 10 ppm for methane (CH₄) is demonstrated.

Illicit drug consumption is posing critical concerns in our society causing health issues, crime-related activities, and the disruption of border trade. The smuggling of illicit drugs urges the development of new tools for rapid on-site identification in cargos. Current methods used by law enforcement officers rely on presumptive color tests and portable spectroscopic techniques. However, these methods sometimes exhibit inaccurate results due to commonly used cutting agents, the colorful nature of the sample or because the drugs are smuggled (hidden or mixed) in common goods. Interestingly, electrochemical sensors can deal with these specific problems. Herein, an electrochemical device is presented that uses affordable screen-printed electrodes for the electrochemical profiling of illicit drugs by square-wave voltammetry (SWV). The identification of the illicit compound is based on the oxidation potential of the analyte. Hence, a library of electrochemical profiles is built upon the analysis of illicit drugs and common cutting agents. This library allows the design of a tailor-made script that enables the identification of each drug through a user-friendly interface (laptop or mobile phone). Importantly, the electrochemical test is compared by analyzing 48 confiscated samples with other portable devices based on Raman and FTIR spectroscopy as well as a laboratory standard method (i.e. gas chromatography – mass spectrometry). Overall, the electrochemical results obtained through the analysis of different samples from confiscated cargos at an end-user site, present a promising alternative to current methods, offering low-cost and rapid testing in the field.

Background: The gold standard for the diagnosis of sleep bruxism (SB) and obstructive sleep apnea (OSA) is Polysmnography (PSG). At the end of the apnea episodes there is frequently a final hy-permotor muscle activity that could act as a confusion factor in the diagnosis of SB with the elec-tromyography portable devices. The aim of this study was to compare the concordance on the number of episodes of SB in a population with OSA, between the diagnosis obtained by PSG, an-alyzed manually by a neurophysiologist and that obtained manually and automatically by a portable electromyography (EMG) and electrocardiography (EKG) device. Methods: Twenty-three subjects underwent one night of polysomnographic study with simulta-neous recording with the EMG-EKG device. The variables referring to the number of episodes and the SB index measured with both tools and analyzed in the manual and automatic modes were compared. Masticatory muscle activity was scored according to published criteria. The sample was segmented by severity of OSA according to AASM criteria. ANOVA, correlations, and the Bland–Altman plot were used to quantify the agreement between both methods. The concordance was calculated through the ICC. Results: The total events of SB per night in the PSG study were on average (8.17), lower than the one obtained with EMG-EKG manual analysis (14.13) and automatic (29.26). Both the SB PSG and Manual EMG-EKG episodes decrease from non-OSA (PSG = 16 ± 13,55, EMG-EKG = 16,83 ±11,58) to severe OSA (PSG = 3,14 ± 4,26, EMG-EKG = 9,86 ± 8,09). However, in the case of automatic EMG-EKG mode: the number of SB episodes in severe OSA doubled (41,23 ± 12,50) with respect to non OSA (24,50 ± 12,19). On average: the EMG-EKG device Automatic analysis measures 21.08 units more than PSG. The results with the manual EMG-EKG analysis improved. Conclusion: There is no concordance between the results obtained in the PSG neurophysiologic analysis and those obtained by means of the EMG-EKG device automatic and manual analysis for the diagnosis of SB in a population mostly with OSA. The OSA could act as a confusion factor in the diagnosis of SB with the electromyography portable devices, but further study is needed.

Here, we present a staged approach for an innovative repurposing of a portable infant humidicrib into a live cell growth, observation, and imaging system. Furthmore, humidicrib can support different variations of “umbilical” bioreactors, and can be used to conduct electrophysiology experiments and in situ immunohistochemistry. Modifications incorporate a closed loop carbon dioxide (CO₂) concentration control system with umbilical CO₂ and heating support for tailored bioreactors. The repurposing cost is inexpensive and allows for the continued observation and imaging of cells. This prototype unit has been used to continuously observe and image live primary neurons for up to 21 days. This demonstrates the repurposed units’ suitability for use in tissue culture based research, particularly where modifications to microscopes are required or where sensitive manipulation outside of a standard incubator is needed.

In this work, we designed a MEMS device which allows simultaneous direct measurement of mechanical properties during deformation under external stress and characterization of the evolution of microstructure of nanomaterials within a transmission electron microscope. This MEMS device makes it easy to establish the correlation between microstructure and mechanical properties of nanomaterials. The device uses piezoresistive sensors to qualitatively measure the force and displacement of nanomaterials, e.g., in wire and thin plate forms. The device has a theoretical displacement resolution of 0.19 nm and a force resolution of 2.1 μN. The device has a theoretical displacement range limit of 2.74 μm and a load range limit of 27.75 mN.

This paper presents laboratory devices on which experimental measurements were carried out to prove the validity of the assumption about the reduction of vibrations transmitted to the conveyor belt structure generated by the impact forces of falling material grains in the places of transfer or on the hoppers of conveyor belts. In order to limit damage to the conveyor belts caused by the impact of the sharp edges of material grains, conveyor belts are supported by impact rollers or impact rubber rods in the places of transfers and on the hoppers of belt conveyors. The flattened ends of the impact rollers are inserted into the grooves of steel brackets installed on the supports of the fixed conveyor idlers of a conventional design. In this paper, a special modification of the fixed conveyor idler is presented, which consists of inserting plastic brackets into the structurally modified roller axle holders of the fixed conveyor idler. Measurements were carried out on the first laboratory device, which showed that the specially modified fixed conveyor idler resulted in a higher damping of up to 15% of the impact forces of the falling weight on the rubberized hoop of the impact roller shell compared to the conventional fixed conveyor idler design. Measurements carried out on the second laboratory device show that the effective vibration velocity values detected at the points where the impact roller axis fits into the fixed roller table holder, i.e. points B and D, are higher than when using plastic brackets, up to 6% for a 108 mm diameter roller, compared to steel impact roller brackets.

This article presents a new input device for spastic patients and others with similar symptoms. The sensor consists of a disc used to determine positions and can replace standard joysticks in medical devices such as electric-powered wheelchairs. Using a standard joystick while operating a powered wheelchair can result in dangerous situations when spastic movements occur and extremities cramp making them uncontrollable. To avoid this, a disc was developed that can be controlled with any body part. By shifting weight (x- and y-axis) the disc can tilt in any direction creating a proportional output signal and can also be pushed down in the center (z-axis) to open a menu on a screen for example. When spasms occur it is impossible for users to get stuck on the input device because the disc is flat and can be mounted within a control panel. Body parts coming into contact with the disc would merely slide across the disc without triggering unintentional actions. The sensor presented here is also adaptive and can be adjusted to fit a user’s strength and range of motion. This proposal aims to develop an input device that enables spastic patients to operate sensitive systems safely.

This paper discusses the design and implementation of a portable IoT station. Communication and data synchronization issues in several installations are addressed here, making possible a detailed analysis of the entire system during its operation. The system proposed is interpreted as an additional tool which can be utilized in several applications, where the system operator requires a synchronized data stream, combining multiple communication protocols into one single time stamp. The hardware selected for the portable IoT station complies with the International Electrotechnical Commission (IEC) industrial standards. A short discussion regarding interface customization shows how easily the hardware can be modified so that it is integrated with almost any system. A Programmable Logic Controller enables the Node-Red to be utilized. This open-source programming tool employs flows to define operations for each global variable nominated in the Modbus register. Two applications are presented and discussed in this paper, each application has a distinct methodology utilized to publish and visualize the acquired data. The portable IoT Station is highly customizable, consisting of a modular structure and providing the best platform for future research and development of dedicated algorithms.

An easy to implement and cost-effective Fiber Bragg Grating (FBG) sensor interrogation technique based on a ring Erbium-Doped Fiber Laser (EDFL) topology is proposed and experimentally assessed. The FBG sensor is part of the EDFL cavity and must have a central wavelength located within the linear region of the EDF’s amplified spontaneous emission (ASE) spectrum which occurs between 1530 and 1540nm. In this manner, the wavelength-encoded response of the FBG under strain is converted to a linear variation of the laser output power, removing the need for spectrum analysis as well as any limitations from the use of external edge-filtering components. In addition, the laser linewidth is significantly reduced with respect to the FBG bandwidth thus improving the resolution of the system, whereas its sensitivity can be controlled through the pumping power. The performance of the system has been characterized by modeling and experiments for EDF's with different lengths, doping concentrations and pumping power levels. The influence of mode-hopping in the laser cavity on the resolution and accuracy of the system has also been investigated.

An advanced, cost-effective and portable DNA biosensor capable of detecting multiple bacteria simultaneously have been developed. The biosensor consists of a fast and inexpensive potentiostat that controls the applied potential to a screen-printed electrochemical array platform functionalized with MoS2 flakes and bacteria DNA probes, and monitors the current response obtained by the use of à la carte thionine functionalized carbon nanodots (Ty-CDs) as electrochemical indicator of the hybridization event. The design of the potentiostat prioritizes achieving an optimal signal-to-noise ratio and incorporates a user-friendly interface compatible with various devices such as computers, mobile phones and tablets. The device is compact, lightweight, and manufactured at a low cost. The key components of the potentiostat include a data acquisition board capable of analyzing multiple samples simultaneously and a controller board. The results obtained confirm the ability of the developed device to successfully detect specific bacteria DNA sequences, demonstrating the reliability and performance of the developed multiplexing portable biosensor with better sensibility than using a traditional, more complex and laboratory oriented potentiostat.

In the present work, a portable device system applied in the detection and classification of different metallic ions was proposed and developed, aiming at its application in the monitoring of hydrological systems like rivers, lakes and groundwater. Considering the system features, a portable colorimetric system was developed by using a multispectral optoelectronic sensor. All the technology of quantification and classification of metallic ions using Optoelectronic Multispectral sensors was fully integrated in the embedded hardware FPGA technology and software based on virtual Instrumentation (NI LabView ®). The system was used as a colorimeter by using the chromogen reagent of 1-(2-pyridylazo)-2-naphthol (PAN) as an indicator and the results obtained together with the signal processing and pattern analysis using the method of the linear discriminant analysis, allowed to obtain excellent results in detection and classification of Pb(II), Cd(II), Zn(II), Cu(II), Fe(III) and Ni(II) ions, with almost the same level of performance in relation to those obtained from the UV-VIS spectrometers of high spectral resolution.

Objective: This study aimed to demonstrate the availability of portable devices for nasal FeNO measurement, which could replace exhaled NO measurement based on the continuous aspiration of multiple flow measurement systems. Methods: A descriptive cross-sectional study. The healthy subjects without rhinosinusis disorders (control group) and those with diagnosed allergic rhinitis (AR group) were enrolled in the study. They underwent nasal and bronchial FeNO measurements by both fixed flow NObreath® connected to nasal mask and multiple flows HypAir FeNO®. Results: A total of 153 people were recruited including 63 healthy subjects and 90 subjects with AR. There were no statistically significant differences in anthropometric characteristics between the two groups (P > 0.05). There were a significant increase in FeNO values in the AR group compared to the control group; concentrations of nasal and bronchial FeNO mearsured by NObreath® were 76.0 ± 50.7 ppb (vs 36.0 ± 28.1 ppb, P < 0.01) and 32.3 ± 15.4 ppb (vs 9.2 ± 5.6 ppb, P < 0.001), and those mearsured by NObreath® Hypair FeNO® were 1796.9 ± 523.3 ppb (vs 400.2 ± 123.1 ppb, P < 0.001) and 37.3 ± 23.0 ppb (vs 17.4 ± 18.3 ppb, P < 0.01). A weak correlation between the values measured by NObreath® and Hypair FeNO® devices was observed (r = 0.023 and r = 0.089, respectively; p < 0.05). Conclusions: The handheld NObreath® device is effective in measuring FeNO concentrations in both normal subjects and AR patients. The advantages in price and size, creating a compact, low-cost device that is convenient for use and research.

Scedosporium species are human pathogenic fungi, responsible for chronic, localised, and life-threatening disseminated infections in both immunocompetent and immunocompromised individuals. Diagnosis of Scedosporium infections currently relies on non-specific CT, lengthy and insensitive culture from invasive biopsy, and time-consuming histopathology of tissue samples. At present, there are no rapid antigen tests that detect Scedosporium-specific biomarkers. Here we report the development of a rapid (30 min) and sensitive (pmol/L sensitivity) lateral-flow device (LFD) test, incorporating a Scedosporium-specific IgG1 monoclonal antibody (mAb), HG12, which binds to extracellular polysaccharide (EPS) antigens of between ~15 kDa and 250 kDa secreted during hyphal growth of the pathogens. The test is compatible with human serum, and allows the detection of the Scedosporium species most-frequently reported as agents of human disease (Scedosporium apiospermum, Scedosporium aurantiacum, and Scedosporium boydii), with limits of detection (LOD) of the EPS biomarkers in human serum of ~0.81 ng/mL (S. apiospermum), ~0.94 ng/mL (S. aurantiacum), and ~1.95 ng/mL (S. boydii). The Scedosporium-specific LFD (ScedLFD) test therefore provides a potential novel opportunity for the detection of infections caused by different Scedosporium species.

Background. To prospectively evaluate the reliability of a portable optical scanner compared to the water displacement technique for volumetric measurements of the foot and ankle, and to compare the acquisition time associated with these two methods. Methods. Foot volume was measured in 29 healthy volunteers (58 feet, 24 female/5 male) by a 3D scanner (UPOD-S 3D Laser Full-Foot Scanner ®) and by water-displacement volumetry. Measurements were performed on both feet, up to a height of 10 cm above the ground. The acquisition time for each method was evaluated. Kolmogorov-Smirnov test, Lin's Concordance Correlation Coefficient, and a Student’s t-test were performed. Results: Mean foot volume was 869.7+/-165.1cm3 (3D scanner) versus 867.9+/-155.4cm3 (water-displacement volumetry) (p <10-5). Concordance of measurements was 0.93, indicative of a high correlation between the two techniques. Volumes were 47.8 cm3 lower when using the 3D scanner versus water volumetry. After statistically correcting this underestimation, the concordance was improved (0.98, residual bias = -0.03 +/- 35.1 cm3). Mean examination time was 4.2 +/-1.7 min (3D optical scanner) versus 11.1 +/-2.9 min (water volumeter) (p<10-4). Conclusion: Ankle/foot volumetric measurements performed using this portable 3D scanner are reliable and fast, and can be used in clinical practice and research.

Nowadays, security is a top priority. In fact, biometrics uses cutting-edge technologies to identify terrorists and criminals. But the practice of distinguishing humans based on intrinsic physical or behavior traits goes back thousands of years. With the widespread use of computers in the late 20th century, new possibilities for digital biometrics emerged and new technologies were generously used. Among these, we remember high resolution security video cameras and drones. So, the aim of the present project is to study and explain the features of these technologies, especially the ones of the the Phantom 4 Pro+ aircraft and analyze its operating methods in order to identify human faces during live streaming of videos. For this purpose, it will be used Paul Viola and Michael Jones’ face detection algorithm, which includes Haar features and cascade classifiers to identify faces, eyes and ears of an individual.

The authors recently proposed a method for on-site dosimetry by a combination of radiochromic film and portable colorimeter. To test and expand the applicability of this method, dosimetric properties of radiochromic reactions were examined for six combinations of two popular Gafchromic films (EBT3 and EBT-XD) and three commercially-available portable colorimeters (nix pro2, nix spectro2 and Spectro1 Pro; abbreviated to “NixP”, “NixS” and “SpoP”, respectively). EBT3 and EBT-XD were irradiated with 160 kV X-rays at 0.3 to 40Gy and 1 to 80 Gy, respectively, and the radiation-induced color levels of RGB and CMMK components were measured with the three colorimeters. Angle dependence was examined by reading at 15° intervals. As results, it was judged that all combinations would work effectively as tools for on-site dosimetry. NixP and NixS showed advantages that they were applicable to a wider dose range for both films, while Spo1 worked better in a lower dose range. On the other hand, Spo1 had an advantageous feature of no angular dependence in reading films, while NixP and NixS showed significant angle-dependent changes. These differences were presumed to attribute to the different geometries of LED light emission; it came from all directions (ring-shape source) in Spo1, 4 directions in NixP, and 8 directions in NixS. These findings would expand the applicability of the proposed on-site dosimetry method to various occasions.

Until recently, the classic approach to mineral exploration studies is to bring the field samples/drill cores collected during field studies to the laboratory followed by laborious analysis procedures to generate the analytical data. This is very expensive, time consuming and difficult for exploring vast areas. But rapid technological advances in field portable analytical instruments such as portable ultraviolet–visible and near-infrared spectrophotometers, gamma ray spectrometer, pXRF, pXRD, pLIBS, and µRaman spectrometer have changed this scenario completely and increased their on-site applications in mineral exploration studies. These instruments are currently providing direct, rapid, on-site, real-time, non-destructive, cost-effective identification, and determination of target elements, indicator minerals and pathfinder elements in rock, soil, and sediment samples. These portable analytical instruments are currently helping to obtain accurate chemical and mineralogical information directly in field with minimal or no sample preparation, and providing decision-making support during field work as well as during drilling operations in several successful mineral exploration programs. In this article, the developments in these portable devices, and their contributions in the platinum group elements (PGE), rare earth elements (REE), gold, base metals, and lithium exploration studies both on land and on ocean bed have been summarized with examples.

Although mammography has been the gold standard for early detection of breast cancer, if a woman has dense breast tissue, a false negative diagnosis may occur. Breast ultrasound, whether hand-held or automated, is a useful adjunct to mammography but adds extra time and cost. The primary aim was to demonstrate that our second-generation Aceso system, which combines full-field digital mammography (FFDM) and automated breast ultrasound (ABUS) in a single platform, is able to produce improved quality images that provide clinically meaningful results. Aceso was first tested using two industry standards: a CDMAM phantom to assess the FFDM images; and the CIRS 054GS phantom to evaluate the ABUS images. In addition, 25 women participated in a clinical trial: 14 were healthy volunteers while 11 were patients referred by the breast clinic at Groote Schuur Hospital. The CDMAM phantom results showed the FFDM results were better than EUREF’s standard of “acceptable” and were approaching “achievable”. The ABUS results showed lateral and axial spatial resolution of 0.5 mm and adequate depth penetration of 80 mm. Our second-generation Aceso system, with its improved quality of clinical FFDM and ABUS images, has demonstrated its potential for early detection of breast cancer in a busy clinic.

An increasing need for better agricultural practices that are sustainable to provide increased yields of crops for the ever increasing food demand to be met for the growing world population is a current necessity. It is estimated by the UN that in 2050 the world’s populace may be as much as 9.8 billion global, yet, farmers still face several obstacles, which includes soil degradation, extreme temperatures, and drought which as increasingly becoming more severe with climate changes. Plant health monitoring is a method that will help to increase awareness about plant enhancing by studying how to increase crop yields while decreasing the environmental impacts. The use of low-cost, controlled environments, soil quality, water levels, and pathogenic and pests attacks can be regularly monitored. Currently, several diagnostic technologies and portable point-of-use methods and technologies are employed for detection of diseases, although, the current available lab-based methods used for plant’s diagnostics test are inadequate for plant point-of-use monitoring. The promotion of use of these point of use methods will enable pathogen detection, poor plant growth, unsuitable environmental conditions and nutrient use efficiency allowing for immediate and timely corrective actions to ensure minimal damage to the plants with maximal yield. Increase in the use of sustainable agri practices are required for ensuring higher yields with minimal inputs and that are non-destructive to the land and the use of improved methodologies and technologies will be useful tools for achieving sustainable agriculture.

In this paper, the design of a low cost portable ventilator with performance analysis have been done to solve the scarcity of respiratory ventilators for COVID-19 patients. The materials used to build the system are: DC motor, rotating disc and pneumatic piston. The system input is the patient heart beat and the output is volume of air to the patient lung with adjusted breathing rate. This ventilator adjusts the breathing rate to the patient depending on his heart beat rate. The performance analysis of this system have been done using Proportional Integral Derivative (PID) and Full State Feedback H2 controllers. Comparison of the system with the proposed controllers have been done using a step change and a random change of the patient heart beat and a promising result have been analyzed successfully.

Cardiac amyloidosis is caused by amyloid fibrils that deposit in the myocardial interstitium, causing restrictive cardiomyopathy and eventually death. The electromechanical, inflammatory, and autonomic changes due to amyloid deposition result in arrhythmias. Atrial fibrillation is by far the most common arrhythmia. Rate control strategy is generally poorly tolerated due to restrictive filling physiology and heart rate dependance, favoring adoption of rhythm control strategy. Anticoagulation for stroke prophylaxis is warranted irrespective of CHA2DS2Vasc score in patients with favorable bleeding profile; data on left appendage closure devices is still insufficient. Ventricular arrhythmias are also not uncommon and the role of implantable cardioverter-defibrillator in cardiac amyloidosis is controversial. There is no evidence of improvement in outcomes when used for primary prevention in these patients. Bradyarrhythmia is most commonly associated with sudden cardiac death in cardiac amyloidosis. Pacemaker implantation can help provide symptomatic relief but does not confer mortality benefit.

The occurrence rate of occupational accidents caused by slipping and falling is 50% worldwide. Determining the slip safety risk is necessary to minimize the accidents caused by slipping in pedestrian walking areas. By on-site testing, this study aims to determine the slip risks of floor coverings used in walking areas with many pedestrians in public service buildings (PSB). For this purpose, on-site measurements were performed in two environments and six locations in PSB using portable GMG 200 and pendulum testers operating according to DIN 51131 and TS EN 14231 standards. These tests were performed on four-floor coverings with polished surface treatment in PSB. Since the floor coverings measured have a polished surface, it can be seen that the dynamic friction coefficients (DCOF) values are very low, and the slip risks are high. By statistically analyzing the slip test data using the K-means method, a new safety classification was made according to the usage areas of floor coverings. To minimize the risk of slip safety, especially for students, patients, and employees in PSB, it is recommended to use floor coverings with high DCOF values and low slip risk.

Iron, a crucial element in our environment, plays a vital role in numerous natural processes. Understanding the presence and concentration of iron in the environment is very important, as it impacts various aspects of our planet’s health. On-site detection and speciation of iron are significant for several reasons. In this context, the present work aims to evaluate the applicability of voltammetry for on-site determination of iron and its possible speciation using a portable voltammetric analyzer. Voltammetry offers the advantage of convenience and cost-effectiveness. For iron (III) determination a modification of a glassy carbon electrode (GCE) with an antimony-bismuth film (SbBiFE) using acetate buffer (pH=4) as supporting electrolyte was used. The technique adopted was Square Wave Adsoptive Cathodic Stripping Voltammetry (SW-AdCSV) and we used 1-(2-piridylazo)-2-naphthol (PAN) as iron (III) ligand. Linearity, repeatability, detection limit and accuracy were determined using synthetic solutions, then a Standard Reference Material (SRM) 1643f - Trace Elements in Water was used for validation measurements in real matrix. The procedure was finally applied to real samples (tap, lake and sea water) and the results obtained were compared by Inductively Coupled Plasma Optical Emission Spectroscopy (ICP-OES). The results obtained demonstrated the excellent applicability of the proposed on-site voltammetric procedure for the determination of iron and its speciation in water.

This paper presents a novel framework for Collaborative Learning Networks (CLNs) in classrooms, aiming to optimize resource utilization and enhance educational services. The study addresses the inefficiencies of traditional education models, particularly the underutilization of computational resources and limited access to specialized software. The proposed framework employs a mix of task-based and random allocation strategies to distribute computational tasks within the CLN, considering each device’s capabilities and task requirements. The findings show significant improvement in resource utilization, facilitated by device-to-device collaboration and task sharing, thus enriching students’ learning experiences. This work contributes to optimizing resource utilization in education, advancing the field of CLNs.

Wafer-scale blue micro-light-emitting diode (micro-LED) arrays are fabricated with a pixel size of 12 μm, a pixel pitch of 15 μm, and a pixel density of 1692 pixels per inch, achieved by optimizing the properties of e-beam-deposited and sputter-deposited indium tin oxide (ITO). Although the sputter-deposited ITO (S-ITO) films exhibit a densely packed morphology and lower resistivity compared to those of the e-beam-deposited ITO (E-ITO) films, the forward voltage (VF) values of a micro-LED with the S-ITO films are higher than those with the E-ITO films. The VF values for a single pixel and for four pixels with E-ITO films are 2.82 V and 2.83 V, respectively, while the corresponding values for S-ITO films are 3.50 V and 3.52 V. This was attributed to ion bombardment damage and nitrogen vacancies in the p-GaN layer. Surprisingly, the VF variations of a single pixel and of four pixels with the optimized E-ITO spreading layer from five different regions are only 0.09 V and 0.10 V, respectively. This extremely uniform VF variation is suitable for realizing micro-LED displays to be used in AR and VR applications, circumventing the bottleneck in the development of long-lifespan and high-brightness organic LED devices for industrial mass production.

Background: Portable oxygen concentrators (POCs) have shown efficacy in delivering adequate oxygen for various patient scenarios; however, there is a lack of research on POCs’ efficacy across different respiratory rates specifically among COPD patients. Methods: This bench study was conducted using the IngMar Medical Active Servo Lung 5000 attached to flexible tubing, which simulated an adult patient’s nares. An oxygen analyzer (Maxtec Handi+) was connected to the tubing 6 inches below the nares to estimate the inspired oxygen concentration at the adult trachea. A standard nasal cannula was placed in the simulated patient nares, which was also attached to each POC. The IngMar Lung was programmed to simulate a COPD patient at the following respiratory rates: 15, 20, 30, and 40 breaths/min. POC devices were then compared to an oxygen wall outlet and a standard oxygen concentrator (non-portable CAIRE device). The POCs included the CAIRE FreeStyle Comfort (with Autosat), CAIRE FreeStyle Comfort (without Autosat), Inogen G4, Inogen G5, Phillips SimplyGo Mini, GCE Zen-O lite, Drive Medical iGo2, and Kingon POCs. Descriptive statistics and ANOVAs were computed to determine statistically significant differences between POCS and control devices (wall oxygen and standalone oxygen concentrator). Results: Across most respiratory rate scenarios, the wall oxygen and standalone oxygen concentrator (control group) resulted higher oxygen measurements compared to the POCs. Among the POCs on setting 2, the highest oxygen measurement for 15, 30, and 40 breaths/min was the CAIRE FreeStyle Comfort with AutoSat on sensitivity 5 (24.43%, 24.81%, and 25.0%, respectively). On setting 2, the 20 breaths/min highest oxygen measurement was the Inogen G4 (24.43%). For setting 5, the highest oxygen measurement for 15 breaths/min and 40 breaths/min was the CAIRE FreeStyle Comfort without AutoSat (31.56% and 26.13%, respectively), while the highest oxygen measurement for 20 breaths/min was the Inogen G5 (30.26%), and the highest oxygen measurement for 30 breaths/min was the CAIRE FreeStyle Comfort with AutoSat on sensitivity level 5 (27.89%). Conclusions: The oxygen administered through the wall and the standalone CAIRE oxygen concentrator all delivered higher oxygen levels compared to the POCs (with the exception of the 40 breaths/min scenario on setting 2). However, among the POCs, the CAIRE Freestyle Comfort with AutoSat, CAIRE Freestyle Comfort without AutoSat, and the Inogen G4 all performed the best among the various breathing rate scenarios.

The present work proposed a low-cost portable device as an enabling technology for Smart Farms using multispectral imaging and Machine Learning in soil texture. Clay is an important factor for the verification and monitoring of soil use due to its fast reaction to chemical and surface changes. The system developed uses the analysis of reflectance in wavebands for clay prediction. The selection of each wavelength is performed through an LED lamp panel. A NoIR microcamera controlled by a Raspberry Pi device is employed to acquire the image and unfold it in RGB histograms. Results showed an good prediction performance with R2 of 0.96, RMSEC of 3.66% and RMSECV of 16.87%. The high portability allows the equipment to be used in a field providing strategic information related to soil sciences.

Layered halide perovskites have emerged as a promising contender in solid-state lighting thanks to their tunable bandgap, high luminescence quantum yield, and high color purity. However, the fabrication of perovskite light-emitting devices in laboratories usually experiences low de-vice-to-device reproducibility since perovskite crystallization is highly sensitive to ambient condi-tions, such as humidity and temperature. Although device processing inside gloveboxes is primarily used to reduce the influence of oxygen and moisture, several extraneous variables, including gas-eous pollution traces and thermal fluctuations in the inert atmosphere or contaminations from re-sidual solvents confined in the enclosed environment, can destabilize the crystallization process and alter the properties of the emissive layers. Here, we examine different experimental set-ups for spin-coating deposition of layered perovskites in inert atmospheres and their influences on the formation of polycrystalline thin films. Our results demonstrate that fluctuations in the glovebox properties (concentrations of residual O2 and H2O or solvent traces), even in very short timescales, can negatively impact the consistency of the perovskite film formation, while thermal variation plays a relatively minor role in this phenomenon. Furthermore, careful storage of chemical species inside the workstation is critical for reproducing high-quality perovskite layers. Consequently, when applying our most controlled environment for perovskite deposition, the photoluminescence life-time of perovskite thin films shows a standard deviation of only 3%, whereas the reference set-up yields a 15% standard deviation. Regarding complete perovskite light-emitting diodes, the uncer-tainties in statistical luminance and EQE data are significantly reduced from 230% and 140% to 38% and 42%, respectively.

Wireless Sensor Networks (WSNs) is considered to be a promising research area since it entails sensing capabilities. WSNs are confronted by fabricated explosion injection attacks and in return results into draining of vitality on sensor nodes routing mainly because of increased capabilities in a broad range of applications where sensor nodes use a battery as the power source. In this paper, we reveal and claim a state-of-the-art model to minimize vitality depletion of nodes within the network in return increases network period to more realistic stretch. It is revealed that the main cause is vitality consumption unbalances in different parts of the network direct resulting from having a static sink. More still, the network nodes neighboring the sink insistently partake in progressing data of other nodes to the sink. Consequently, the network nodes are supplementarily subjected to untimely vitality exhaustion. This paper mainly provides a novel movable (mobile) fuzzy logic sink approach and an intelligent system like expect systems that are able to scrutinize network situation, and make the superlative choice for spreading the network period robotically.

Currently Single Board Computers (SBCs) are sufficiently powerful to run Real-Time Operating Systems (RTOSs) and applications with real-time attributes and requirements. SBCs serve as a foundation in Industrial Internet of Things (IIoT). The NXP Semiconductors produces a series of SBCs based on ARM-processors for a variety of industrial applications. The continuous increase in real-time data generated by IoT devices adds further research issues about the efficiency of such systems and applications. The purpose of this research was to investigate the timing performance of an NXP TWR-K70F120M device with μClinux OS on running concurrently tasks with real-time features and constraints. A custom-built multithreaded application with specific compute-intensive sorting and matrix operations was developed and applied to obtain measurements in specific timing metrics, including task’s execution time, threads waiting time, and response time, under different threads variations. The performance of this device was additionally benchmarked and validated against favorite platforms, a Raspberry Pi4 and BeagleBone AI SBCs. The experimental results showed that this device stands well both in terms of timing and efficiency metrics. Execution times were quite lower than the others, by approximately 56% in the case of two threads, and by 29% in the case of thirty-two threads configurations.

Melasma is a challenging skin condition which involves both structural and functional skin alterations. Despite the availability of various treatment options, the management remains complex. This is the first study to investigate topical application of Rosa Damascena stem cell exosomes when used concomitantly with microneedling in women and men with facial melasma. We recruited 20 subjects with Fitzpatrick skin types I-III, exhibiting melasma of varying severity. The modified Melasma Area and Severity Index (mMASI) and Global Aesthetic Improvement Scale (GAIS) were utilized to evaluate treatment response. The treatment protocol involved microneedling followed by exosome application over four or five sessions, at 4-week intervals. Ninety percent of subjects demonstrated a significant improvement in mMASI scores, while only 10% showed no change. GAIS assessment further supports overall improvement, with just 10% categorized as "not changed". Tolerability was favorable, with mild, transient side effects. Our findings suggest promising outcomes with this combined therapy, underscoring its potential as a safe and effective approach for treating melasma, particularly in severe and moderate cases. However, further research with larger sample sizes and control arms is warranted to validate these findings and explore long-term efficacy.

In this paper, a 100CMM regenerative thermal oxidizer (RTO) system based on a high heating device for low-emission combustion is implemented at a volatile organic compound (VOCs) gas generation workplace. Existing RTO has a structure that repeats the inflow and discharge of VOCs gas into a cylindrical drum-type rotating disk and has excellent energy efficiency with a heat recovery rate of 95% or more. However, when used for a long time, there is a problem that rotation stops or explodes due to the discharge of pollutants due to dust and thermal expansion due to high temperature of 800℃. To overcome this, a RTO based on a high heating device was developed to reduce low-emission combustion emissions and energy use. Through 177 hours of demonstration time, the oxidation efficiency of VOCs was 98.87%; the waste heat recovery rate was reduced by 95.78%, the fuel consumption was reduced by 21.95%, and the nitrogen oxide concentration was 3.9 ppm

In this paper, a 100CMM regenerative thermal oxidizer (RTO) system based on a high heating device for low-emission combustion is implemented at a volatile organic compound (VOCs) gas generation workplace. Existing RTO has a structure that repeats the inflow and discharge of VOCs gas into a cylindrical drum-type rotating disk and has excellent energy efficiency with a heat recovery rate of 95% or more. However, when used for a long time, there is a problem that rotation stops or explodes due to the discharge of pollutants due to dust and thermal expansion due to high temperature of 800℃. To overcome this, a RTO based on a high heating device was developed to reduce low-emission combustion emissions and energy use. Through 177 hours of demonstration time, the oxidation efficiency of VOCs was 97.87%; the waste heat recovery rate was reduced by 95.78%, the fuel consumption was reduced by 21.95%, and the nitrogen oxide concentration was 3.9 ppm

In this study, the resource blocks (RB) are allocated to user equipment (UE) according to the evolutional algorithms for long term evolution (LTE) systems. Particle Swarm Optimization (PSO) algorithm is one of the evolutionary algorithms, based on the imitation of a flock of birds foraging behavior through learning and grouping the best experience. In previous work, the Simple Particle Swarm Optimization (SPSO) algorithm was proposed for RB allocation to enhance the throughput of Device-to-Device (D2D) communications and improve the system capacity performance. In simulation results, with less population size of M = 10, the SPSO can perform quickly convergence to sub-optimal solution in the 100^th generation and obtained sub-optimum performance with more 2 UEs than the Rand method. Genetic algorithm (GA) is one of the evolutionary algorithms, based on Darwinian models of natural selection and evolution. Therefore, we further proposed a Refined PSO (RPSO) and a novel GA to enhance the throughput of UEs and to improve the system capacity performance. Simulation results show that the proposed GA with 100 populations, in 200 generations can converge to suboptimal solutions. Therefore, with comparing with the SPSO algorithm the proposed GA and RPSO can improve system capacity performance with 1.8 and 0.4 UEs, respectively.

The COVID-19 pandemic caused by the virus SARS-CoV-2 has been the greatest global threat to human health in the last three years. The most widely used methodologies for the diagnosis of COVID-19 are quantitative reverse transcription polymerase chain reaction (RT-qPCR), used to detect the viral genome, and rapid antigen tests (RATs), also known as lateral flow tests, that employ specific antibodies to detect the viral spike protein. While PCR is considered the gold standard test in terms of specificity and sensitivity, it is time-consuming and requires specialized instrumentation operated by skilled personnel. In contrast, RATs can be used in-home or at point-of care but are less sensitive leading to a higher rate of false negative results. An alternative methodology for the detection of virus is the use of electrochemical biosensors that employ disposable strip electrodes to which binding of viral components elicits a change in electrical signal. Laser-scribed graphene (LSG) electrodes are attractive candidates for use as biosensors electrodes suitable for SARS-COV-2 detection due to their low-cost, patternability and ease of fabrication. In this work, we describe the development of a biosensor for COVID-19 detection that exploits a split-ester bond ligase system (termed ‘EsterLigase’) for immobilization of a virus-specific nanobody to maintain the out-of-plane orientation of the probe to ensure the efficacy of the probe-target recognition process. An anti-spike VHH E nanobody, genetically fused with the EsterLigase domain, was used as the specific probe for the spike receptor-binding domain (SP-RBD) protein as the target. The recognition between the two was measured by the change in the charge transfer resistance, determined by fitting the electrochemical impedance spectroscopy (EIS) spectra. The developed LSG-based biosensor achieved a linear detection range for the SP-RBD from 15 pM to 150 nM with a sensitivity of 0.0866 [log(M)]-1 and a limit of detection (LOD) of 7.68 pM.

This study presents a fit-for-purpose evaluation of commercially available portable sensor systems, measuring PM, NO2 and/or BC, through extensive lab- and field benchmarking. The main aim of the study is to identify sensor systems that can be used for mobile monitoring by citizens to assess dynamic exposure in ambient air. After an initial literature study and market search resulting in 39 sensor systems, 10 sensor systems were ultimately purchased and benchmarked in laboratory and real-word conditions. We evaluated comparability to reference analyzers, sensor precision and sensitivity to temperature, humidity and O3. Moreover, we evaluated if accuracy can be improved by the lab and field calibration. Because the targeted application of the sensor systems under evaluation is mobile monitoring, we conducted a mobile field test in an urban environment to evaluate the GPS accuracy and potential impacts from vibrations on the resulting sensor signals. Results of the considered sensor systems indicate that out-of-the-box performance is relatively good for PM and BC, but maturity of the tested NO2 sensors is still low and additional efforts are needed in terms of signal noise and calibration. The horizontal accuracy of the build-in GPS was generally good achieving a &lt;10m horizontal accuracy for all sensor systems. More accurate and dynamic exposure assessments in contemporary urban environments are crucial to study real-world exposure of individuals and exposome impacts on potential health endpoints. A greater availability of mobile monitoring systems capable of quantifying urban pollutant gradients will further boost this line of research.

Agricultural drainage canals that connect upstream fish spawning areas to downstream rivers and lakes serve as crucial habitats for migrating fish. However, disconnections, such as drops and chutes, have been constructed in these canals due to agricultural modernization and flood control measures, hindering the movement of fish with limited swimming abilities. Portable fishways offer a promising solution to reconnect water bodies in agricultural canals, as they can be easily removed during high water discharges to avoid impeding the canals' drainage function. In addition to experimental assessments of fishway functionality, employing a hydrodynamic model to explore effective placement strategies for portable fishways is essential to maximize their effectiveness. This study presents a method to determine the best horizontal location of a portable fishway in an agricultural drainage canal using two-dimensional hydrodynamic simulations within the specified cases. The applicability of this method is demonstrated by addressing the positioning challenge of a portable fishway on a chute in an agricultural drainage canal in Japan. Results indicate that the proposed method allows for the selection of a suitable location, considering preferable hydraulic conditions both within the portable fishway and around its entrance.

As cardiovascular diseases continue to be a leading cause of mortality, recent-ly, wearable devices for monitoring cardiac activity have gained much interest among medical community. This paper introduces an innovative ECG monitoring system based on a single – lead ECG machine enhanced with machine learning methods. The system only processes and analyses the ECG data, but also predict potential heart disease at an early stage. The wearable device was built on the ADS1298 and a microcontroller STM32L151xD. A server module based on REST API architecture style was designed to fa-cilitate interaction with web-based segment of the system. The module is responsible for receiving data in real time from microcontroller and their deliver to web – based segment. Algorithms for analyzing ECG signals have been developed, including band filter artifact removal, K-means clustering for signal segmentation, and PQRST analysis. Machine leaning methods as Isolation Forest have been employed for ECG anomaly detection. Moreover, a comparative analysis with various machine learning methods, including lo-gistic regression, random forest, SVM, XGBoost, decision forest and, CNNs was conducted to predict cardiovascular diseases. Convoluted Neural Networks (CNN) showed an accu-racy of 0.926, proving high effectiveness in ECG data process.

The article analyzes existing materials and structures with quadratic-nonlinear optical properties that can be used to generate a difference frequency in the terahertz and sub-terahertz frequency ranges. The principle of constructing a nonlinear optical-radio converter, based on an optical focon (a focusing cone), is proposed. Based on the assumption that this focon can be implemented from the metal-organic framework (MOF), we propose a technique for modeling its parameters. The mathematical model of the process of propagation and nonlinear interaction of waves inside the focon is based on a simplification of the nonlinear wave equation. Within the framework of the developed model, the following parameters are approximately determined: the 3D gradient of the linear refractive index and the function determining the geometric profile of the focon, which provide a few-mode-based generation of the difference frequency.

Computers have evolved over the years and as the evolution continues, we have been ushered into an era where high-speed internet has made it possible for devices in our homes, hospital, energy and industry to communicate with each other. This era is what is known as the Internet of Things (IoT). IoT has several benefits in the health, energy, transportation and agriculture sectors of a country’s economy. These enormous benefits coupled with the computational constraint of IoT devices which makes it difficult to deploy enhanced security protocols on them make IoT devices a target of cyber-attacks. One approach that has been used in traditional computing over the years to fight cyber-attacks is Intrusion Detection System (IDS). However, it is practically impossible to deploy IDS meant for traditional computers in IoT environments because of the computational constraint of these devices. In this regard, this study proposes a lightweight IDS for IoT devices using an incremental ensemble learning technique. We used Gaussian Naive Bayes and Hoeffding tree to build our incremental ensemble model. The model was then evaluated on the TON IoT dataset. Our proposed model was compared with other state-of-the-art methods proposed and evaluated using the same dataset. The experimental results show that the proposed model achieved an average accuracy of 99.98\%. We also evaluated the memory consumption of our model which showed that our model achieved a lightweight model status of 650.11KB as the highest memory consumption and 122.38KB as the lowest memory consumption.

A portable urea sensor for use in the fast flow condition was fabricated using porous polytetrafluoroethylene (PTFE) membranes coated with amine-functionalized parylene, parylene-A, by vapor deposition. To generate a specific electrochemical sensor signal from urea, the urea-hydrolyzing enzyme urease was immobilized on the parylene-A-coated PTFE membranes via chemical crosslinking using glutaraldehyde. The urease-immobilized membranes were assembled in a polydimethylsiloxane (PDMS) fluidic chamber, and a screen-printed carbon three-electrode system was used for electrochemical measurements. The success of urease immobilization was confirmed using fluorescence microscopy, scanning electron microscopy, and Fourier-transform infrared spectroscopy. The optimum concentration of urease for immobilization on the parylene-A-coated PTFE membranes was determined to be 48 mg/mL, and the optimum number of membranes in the PDMS chamber was found to be 8. Using these optimized conditions, we fabricated the urea biosensor and monitored urea samples under various flow rates ranging from 0.5 to 10 mL/min in the flow condition using chronoamperometry. To test the applicability of the sensor for physiological samples, we used it for monitoring urea concentration in the waste peritoneal dialysate of a patient with chronic renal failure, at a flow rate of 0.5 mL/min.

African scientific research faces formidable challenges, particularly with limited access to state-of-the-art measurement instruments. The high cost associated with these devices presents a significant barrier for regional research laboratories, impeding their ability to conduct sophisticated experiments and gather precise data. This predicament not only hampers the individual laboratories but also has broader implications for the African scientific community and the advancement of knowledge in developing nations—the financial cost barrier considerably impacts the research quality of these laboratories. Reflection on technical and economical solutions needs to be quickly found to help these countries advance their research. In civil Engineering, the thermal conductivity property is the most important measurement for characterising heat transfer in construction materials. Existing devices (i.e., conductometers) in a laboratory are expensive (approximately 30,000 euros) and unavailable for some African laboratories. The study proposes a new and affordable device to evaluate thermal conductivity in construction materials. The method involves establishing a thermal flux between a heat source ( from the Joule effect provided by steel wool where a current is circulating) and a cold source (generated by ice cube) under steady-state conditions. The development of the cylindrical prototype is based on the comparative flux-meter method outlined in the measuring protocol of the ASTM E1225 standard document. Experiments were conducted on four distinct materials (polystyrene, wood, agglomerated wood, and rigid foam). The results indicate a correct correlation between the experimental values obtained from the newly developed prototype and the reference values found in the literature. For example, concerning the experimental polystyrene study, the detailed case analysis reveals a good correlation, with a deviation of only 4%. The percent error found falls within the acceptable range indicated by the standards recommendations of the ASTM E1225 standard, i.e., within 5% acceptable error.

The proliferation of radio frequency devices in today's society, especially in smart homes, Internet of Things devices, and smartphones, underscores the urgent need for robust identification methods to strengthen cybersecurity. This paper delves into the field of radio frequency fingerprinting to propose a Bluetooth device identification method based on the application of the Jensen-Shannon divergence to the statistical distribution of noise in Bluetooth signals. A detailed case study is performed to investigate the Bluetooth radio frequency noise recorded at 5 Gsps from different devices is investigated to define a statistical radio frequency fingerprint for each Bluetooth device. A noise model is used to extract a unique, universal, persistent, recoverable, and robust statistical radio frequency fingerprint that identifies each Bluetooth device. Then, using the Jensen-Shannon divergence, different noise signals provided by each Bluetooth device are compared with the statistical radio frequency fingerprint of all devices and a membership resolution is declared. The study shows that the proposed method can discriminate between devices of the same brand and model, achieving an identification effectiveness of 99.5 \%. By leveraging the statistical radio frequency fingerprint of Bluetooth devices, this research not only contributes to the advancement of the field of implicit device authentication systems based on wireless communication but also provides valuable insights into the practical implementation of radio frequency identification techniques that could be useful in forensic processes.

The application of electrode-based microfluidic devices in biological entity often imposes a problem due to joule heating. The strong applied potentials or micro channels having narrow cross sections generate undesirable temperature inside the microfluidic channels leading to strong thermal distribution inside the micro channel. When intrinsic distribution of temperature, if not fix with threshold value, causes device damage or cell loss. In this work, we investigate the effects of temperature generated due to joules heating effects and we attempt to address the design constraints for minimizing the joule heating effects in the microfluidic device for developing effective microfluidic device. The device reliability was analyzed under different parametric constraints for various types of substrate materials (PDMS, PMMA, Polyimide and glass). We also attempt to investigate the effects of cell reliability due to strong temperature gradients generated through different applied potentials on different cell types. Furthermore, the response of the device performance due to different electrode configuration and different conductivity of the medium was also studied. Our investigation will eventually provide guidelines for microfluidic researchers to fabricate efficient electrode based microfluidic device which will ultimately help to choose a critical channel dimensions, threshold potentials, and conductivity of solutions in order to avoid device damage and cell loss.

Background: A Morel–Lavallée lesion (MLL) is a traumatic, internal closed degloving injury that results from shearing of subcutaneous tissue away from underlying fascia, usually associated with high-velocity trauma. Case presentation: A 52-year-old man was transported to hospital for further follow-up of a superficial femoral artery injury. Examination on admission showed bruising seen around the left thigh. Contrast-enhanced computed tomography of the left thigh revealed hematoma with extravasation from a branch of the left superficial femoral artery, but no apparent aneurysms or femoral fractures. The patient was treated with compression bandages and discharged on hospital day 6. He left hospital able to walk unaided. He subsequently complained of left thigh pain with swelling and visited the hospital several times. He was treated at another outpatient clinic and was diagnosed with MLL. Single-use disposable portable negative pressure wound therapy (NPWT) was applied for about 2 months, achieving a stable wound site. Conclusion: We encountered a case of MLL successfully treated with single-use portable NPWT. This report presents the case of a patient with isolated MLL without fracture in the left thigh, in which the diagnosis was missed on initial admission. Finally, the patient received minor interventions including drainage along with tissue debridement and portable NPWT. We reviewed the relevant literature and summarize the pathogenesis, clinical manifestations, and treatment strategies for MLL. Emergency physicians require an increased understanding of MLL to avoid misdiagnosis and missed diagnosis.

(1) Background: The imaging energy range of a typical Compton camera is limited due to the fact that scattered gamma photons are seldom fully absorbed when the incident energies are above 3 MeV. Further improving the upper energy limit of gamma-ray imaging has important application significance in active interrogation of special nuclear materials and chemical warfare agents, as well as range verification of proton therapy; (2) Methods: To realize gamma-ray imag-ing in a wide energy range of 0.3~7 MeV, a principle prototype, named a portable three-layer Compton camera, was developed using the scintillation detector that consist of an silicon photo-multiplier array coupled with a Gd3Al2Ga3O12:Ce pixelated scintillator array. Implemented in a list-mode maximum likelihood expectation maximization algorithm, a far-field energy-domain imaging method based on two-interaction and three-interaction events was applied to estimate the initial energy and spatial distribution of gamma-ray sources. The simulation model of detec-tors was established based on Monte Carlo simulation toolkit Geant4. The reconstructed images of a 133Ba, a 137Cs and a 60Co point-like sources were successfully obtained with our prototype in laboratory tests and compared with simulation studies; (3) Results: The proportion of effective imaging events accounted for about 2%, which made our prototype realize reconstructing the distribution of a 0.05 μSv/h 137Cs source in 10 seconds. The angular resolution for resolving two 137Cs point-like sources was 15°. Additional simulated imaging of the 6.13 MeV gamma-rays from 14.1 MeV neutron scattering with water preliminarily demonstrated the imaging capability for high incident energy; (4) Conclusions: We concluded that the prototype had good imaging per-formance in a wide energy range (0.3~7 MeV), which showed potential in several MeV gam-ma-ray imaging applications.

This article discusses the use of a hand held electronic nose to obtain information on the presence of some aromatic defects in natural cork stoppers, such as haloanisoles, alkylmethoxypyrazines and ketones. The proposed prototype has been developed as an instrumentation system with up to eight commercial gas sensors. Machine learning algorithms such as k-nearest neighbors and artificial neural networks has been used. The use of this system tries to improve the current aromatic defect detection process in the cork stopper industry, which is done by gas chromatography or human test panels.

This manuscript critically reviews the design and delivery of spray-dried particles for the achievement of high total lung doses (TLD) with a portable dry powder inhaler. We introduce a new metric termed the product density, which is simply the TLD of a drug divided by the volume of the receptacle it is contained within. The product density is given by the product of three terms: the packing density (the mass of powder divided by the volume of the receptacle), the drug loading (the mass of drug divided by the mass of powder), and the aerosol performance (the TLD divided by the mass of drug). This manuscript discusses strategies for maximizing each of these terms. Spray drying at low drying rates with small amounts of a shell-forming excipient (low Peclet Number) leads to formation of higher density particles with high packing densities. This enables ultrahigh TLD (>100 mg of drug) to be achieved from a single receptacle. Emptying of powder from capsules is directly proportional to the mass of powder in the receptacle, requiring an inhaled volume of about 1 L for fill masses between 40 and 50 mg and up to 3.2 L for a fill mass of 150 mg.

Botulinum neurotoxin (BoNT) intoxication can lead to the disease botulism, characterized by flaccid muscle paralysis that can cause respiratory failure and death. Due to the significant morbidity and mortality costs associated with BoNTs high toxicity, developing highly sensitive, rapid, and field-deployable assays are critically important to protect the nation’s food supply against either accidental or intentional contamination. We report here that the B-cell based biosensor assay (CANARY^® Zephyr) detects BoNT/A in buffer and various food matrices rapidly in ≤ 40 min, in small volumes ≈ 50 μL, with minimal processing of samples, and is extremely portable (suitcase-sized equipment). BoNT/A was detected at limits of detection (LOD) < 0.075 ng ± 0.02 in assay buffer while milk matrices (non-fat, 2 %, whole milk) increased the LOD to < 0.175 – 0.314 ng. Limits of detection for the assay in complex foods were < 1 ng ± 0.0 (neutralized acidic juices-carrot, orange and apple); < 16.7 ng ± 7.7 (liquid egg); and varied from < 0. 39 – 3.125 ng for solid complex foods (ground beef, green bean baby puree, smoked salmon). These results show that the CANARY^® Zephyr assay can be a highly useful tool in clinical, environmental, and food safety surveillance programs.

Glucose is a simple sugar molecule. The sugar molecule is chemically symbolised as C6H12O6. This means that the glucose molecule contains 6 carbon atoms (C), 12 hydrogen atoms (H) and 6 oxygen atoms (O). In human blood, the molecule glucose circulates as blood sugar. Normally after eating or drinking, our body breaks down the sugars in food and uses them to obtain energy for our cells. To do this, our pancreas produces insulin. Insulin "pulls" sugar from the blood and puts it into the cells for use. If someone has diabetes, their pancreas can't produce enough insulin. As a result, the level of glucose in the blood rises. This can lead one to many potential complications, including blindness, disease, nerve damage, amputation, stroke, heart attack and damage to blood vessels etc. In this study, a non-invasive method for monitoring blood glucose has been developed and is therefore easily usable. The device developed can measure the glucose level continuously and eliminates the disadvantages of the invasive system. Near-IR sensors (optical sensors) were used to estimate the concentration of glucose in the blood; these sensors have a wavelength of 940 nm. The sensor is placed on the tip of the finger and the output of the optical sensor is then connected to the microcontroller at the analogue input. Another sensor used, but only to provide more medical information was the heartbeat sensor. After processing and regression analysis, the glucose level is predicted, and data is sent via the Bluetooth network to a developed APP. The results of the implemented device were compared with available invasive methods. The study consists of a hardware platform inserted into an armband and then a small black parallelepiped-shaped box in which the optical sensors are inserted. The hardware consists of a microcontroller, a Near-IR optical sensor, a heartbeat sensor and a Bluetooth module.

Vacuum pump wear is the most prevalent failure mode of the IBA Synthera® automated radiochemistry system. Rebuilding or replacing the pump causes equipment downtime and increases the radiation exposure of the service personnel. We built a dedicated test device to assess new or rebuilt pumps prior to installation, thus reducing downtime and radiation exposure during repairs. The Testbed incorporates a microprocessor that actuates the pump, valves, pressure sensor, and communicates with the user through lights, buttons, and an alphanumeric screen. The Testbed increases productivity and safety in the radiochemistry laboratory.

Thermoelectrics, in particular solid-state conversion of heat to electricity and vice versa, is expected to be a key energy harvesting and temperature management solution in coming years. There has been a resurgence in the search for new materials for advanced thermoelectric energy conversion applications and to enhance the properties of existing materials. In this paper, we review recent efforts on improving figure-of-merit (ZT) through alloying and nano structuring. As heatsink characteristics dictate the performance of thermoelectric modules, various types of heatsink designs has been investigated. Several reported strategies for improving ZT are critically assessed. A notable increase in figure-of-merit of thermoelectric materials (TE) has opened up new areas of applications especially in the medical field. Peltier cooling devices are widely employed for patient core temperature control, skin cooling, medical device and laboratory equipment cooling. Application of these devices in the medical field both in temperature control and power generation has been studied in detail. It is envisioned that this study will provide profound knowledge on the thermoelectric based materials and its role in medical applications.

This paper presents a device for measuring and maintaining the constant water level in a tank. The device uses a capacity sensor to measure the water level. The sensor has a DC voltage output proportional to the water level in the tank. This voltage can be used in other automation too. The water level, in percentages, is displayed on a vu meter with 8 LEDs. The circuit for maintaining the constant level consists in a comparator with hysteresis. The level of the water is adjustable, using a reference voltage from a potentiometer (marked in percentages). The level of the water is compared with the prescribed level and the difference between them commands the start/stop of the water pump which supplies the tank through a relay. The device is powered by 220 V and is isolated from the environment.

Nowadays, the combination of fingerprinting methodology with friendly environmental and economical analytical instrumentation are becoming increasingly relevant in the food sector. In this study, a highly versatile portable analyser based on Spatially Offset Raman Spectroscopy (SORS) to obtain the edible vegetable oils (sunflower and olive oils) fingerprints was used to evaluate the capability of such fingerprints, obtained quickly, reliable and without any sample treatment, to discriminate/classify the analysed samples. After data treatment, not only HCA and PCA as unsupervised pattern recognition techniques but also SVM, kNN and SIMCA as supervised pattern recognition techniques, showed that the main effect over the discrimination/classification was associated to those regions of RAMAN fingerprint related to the free fatty acids content, especially oleic and linoleic acid. These facts allowed the discrimination attending to the original raw material used in the oil's elaboration. In all the model established, reliable qualimetric parameters were obtained.

Abstract: Windtech device is a novel tool for measuring the sensation of the ‘cold’. Cold poses numerous challenges for industrial operations, human survival, and living convenience. The impact of the cold is not possible to be quantified just based on temperatures; however other factors such as wind speed, humidity, irradiance have to be taken into consideration. Efforts have been made to develop combined indices such as wind chill temperature (WCT), AccuWeather RealFeel®, and others. The presented article discusses these along with the industrial standards that emphasize on the quantification of the ‘cold’. The following article introduces the Windtech device and its operating principle involving ‘heated temperature’, where the ‘heated temperature’ is affected by environmental parameters including ambient temperature, humidity, wind velocity, and irradiance. The discussed Windtech device is calibrated for operation according to the ISO 11079:2007 standard.

Ankle joint flexion and extension exercises play an important role in the rehabilitation training of patients who have been injured or bedridden for a long time before and after surgery. Accurately guiding patients to perform ankle flexion and extension exercises can significantly reduce deep vein thromboembolism. Currently, most ankle rehabilitation devices focus on assisting patients with ankle flexion and extension movements, and there is a lack of devices for effectively monitoring these movements. In this study, we designed an ankle joint flexion and extension movement monitoring device based on a pressure sensor. It is composed of an STM32 microcontroller, a pressure sensor, an HX711A/D conversion chip, and an ESP8266 WiFi communication module. The value of force and effective number of ankle joint flexion and extension movements were obtained. An experimental device was designed to verify the accuracy of the system. The results showed that the device can effectively monitor and control ankle flexion and extension movements remotely, ultimately ensuring that the patient can effectively monitor and grasp the active ankle pump movement.

(1) Introduction: External high volume extraction devices may offer a way to reduce any aerosol particulate generated. The aim of this study was to measure the particle count during dental aerosol procedures and compare the results to when a High Volume Extraction device is used; (2) Methods: A comparative clinical study measuring the amount of PM1, PM2.5 and PM10 aerosol particulate with and without the use of an external High Volume Extraction device was undertaken. In total, 10 restorative procedures were monitored with an an industrial Trotec PC220 particle counter. The air sampler was placed at the average working distance of the clinicians involved in the study - 420mm.; (3) Results: In the present study aerosol particulate was recorded at statistically significantly increased levels during dental procedures without an external high volume extraction device versus with the device. The null hypothesis was rejected, in that significant differences were found between the results of the amount of aerosol particle count with and without a High Volume Extraction device.; (4) Conclusion: If the results of the present study are repeated in an in vivo setting, an external high volume suction device may potentially lower the risk of transmission of viral particulate.

Background: Maladaptive neuroplasticity related learned response in substance use disorder (SUD) can be ameliorated using non-invasive brain stimulation (NIBS); however, inter-individual variability needs to be addressed for clinical translation. Objective: Our first objective was to develop a hypothesis for NIBS for learned response in SUD based on competing neurobehavioral decision systems model. Next objective was to conduct computational simulation of NIBS of cortico-cerebello-thalamo-cortical (CCTC) loop in cannabis use disorder (CUD) related dysfunctional “cue-reactivity” – a closely related construct of “craving” that is a core symptom. Our third objective was to test the feasibility of our neuroimaging guided rational NIBS approach in healthy humans. Methods: “Cue-reactivity” can be measured using behavioral paradigms and portable neuroimaging, including functional near-infrared spectroscopy (fNIRS) and electroencephalogram (EEG), metrics of sensorimotor gating. Therefore, we conducted computational simulation of NIBS, including transcranial direct current stimulation(tDCS) and transcranial alternating current stimulation(tACS) of the cerebellar cortex and deep cerebellar nuclei(DCN), of the CCTC loop for its postulated effects on fNIRS and EEG metrics. We also developed a rational neuroimaging guided NIBS approach for cerebellar lobule (VII) and prefrontal cortex based on healthy human study. Results: Simulation study of cerebellar tDCS induced gamma oscillations in the cerebral cortex while tTIS induced gamma-to-beta frequency shift. Experimental fNIRS study found that 2mA cerebellar tDCS evoked similar oxyhemoglobin(HbO) response in-the-range of 5x10-6M across cerebellum and PFC brain regions (=0.01); however, infra-slow (0.01–0.10 Hz) prefrontal cortex HbO driven(phase-amplitude-coupling, PAC) 4Hz, ±2mA (max.) cerebellar tACS evoked HbO in-the-range of 10-7M that was statistically different (=0.01) across those brain regions. Conclusion: Our healthy human study showed the feasibility of fNIRS of cerebellum and PFC as well as fNIRS-driven ctACS at 4Hz that may facilitate cerebellar cognitive function via the frontoparietal network. Future work needs to combine fNIRS with EEG for multi-modal imaging.

People counting applications have been used in diverse applications. The ability and accuracy of thermal imaging over conventional image cameras has led to the implementation of thermal cameras in people counting applications. This paper present a thermal people counting smart glass windows. The people counting application would be remotely monitored from a single centralized PC station as it’s connected to a multiplex of mass monitoring of 20 thermal camera, all embedded into different glass windows. The thermal cameras would then be able to detect body temperatures of all individuals who pass through any of the camera range and also count the numbers of people who passed through the camera range. The data gotten can then be further utilized in various ways, example is in the control of air conditioning and lightening.

This paper presents the formative assessment to implement mobile portable chest X-ray (PDX) machines for Tuberculosis (TB) contact tracing in Oyo and Osun States, Nigeria. This descriptive qualitative study was carried out in 8 Local Government Areas, and 24 FGDs and 33 KIIs were conducted using a 4-stage sampling technique to select participants. Validated transcribed notes were entered and analysed using Nvivo. The respondents' ages ranged from 17-85 years, with a mean age of 42.08±14.9 years, and 4.0% had a postgraduate degree. The majority of the government officials stated that deploying the PDX machine intervention at the community level is the best means as it offers a level of convenience to the community members in the sense that there will be limited disruption to their daily activities as well as zero concerns about the cost of transportation to the health facility. The portable X-ray machine intervention should be implemented at the community level for contact tracing to allow more TB contacts living with the index patient to be screened. However, the PDX machine can also be set up in a special location, and the TB contacts can be invited for the screening.

Six mode shapes, including bending and torsion, were documented for five different basketball rims and backboards at the United States Military Academy, West Point, New York, USA. The frequency and damping ratio of each mode shape were also determined. The empirical process began with the time-domain excitation and response of each rim-backboard system. The impulse of excitation came from an impact hammer separately applied to sequentially, to each node. The sinusoidal response was gathered from an accelerometer at a fixed location, node 1. Each time-domain excitation-response was then converted to a frequency domain Bode plot for each node by a B&K 2034 Signal Analyzer, giving transfer functions of output/input versus frequency. Structural Measurements System (SMS) Software was used to fit mode shapes to the Bode plots. Each of the six mode shapes were fitted to the Bode plots of each node at a specific modal frequency. Each of the six mode shapes were a function of the locations of the nodes, and the Bode plot gathered at each node. The first and second modes were critical for showing that the Energy Rebound Testing Device statistically correlated with the energy transferred to the rim and backboard. A known perturbation mass was selectively attached to the rim, to help isolate the dynamic masses and spring rates for the rim and backboard, to ascertain the kinetic energy transferred to the rim had a 95.67% inverse correlation with rim stiffness.

A selective permeable membrane between two different solutions can generate osmotic pressure, Donnan potential, and ion/pH gradients based on various factors such as membrane type, solute concentration and temperature. In this study, we introduce a novel method for extracting energy from ion gradients through an innovative cycle, presenting intriguing experimental findings. Additionally, by leveraging Raoult’s Law, which describes the relationship between vapor pressure and solute presence, in conjunction with osmosis within a closed system, we successfully engineer the simplest iteration of Maxwell’s demon device. This pioneering approach to sustainable energy generation harnesses ambient temperature marking a significant advancement in energy research. Finally this renewable energy source is available all the time and everywhere.

We compare two methods for creating a microfluidic device from an initial positive master with the same surface relief as the final device. The first method uses urethane or epoxy resin to create an intermediate master for PDMS casting. This method has a very low failure rate but a longer processing time. The second method utilizes PDMS double casting where the intermediate master is passivated PDMS. This method has a higher failure rate but a significantly shorter processing time. Detailed methodology for both methods is included along with a comparison of the strengths and weaknesses of each method. The resin intermediate is a simpler method while PDMS double casting is faster and more scalable. Ultimately it is found that PDMS double casting is preferable in most situations.

Cellular response to mechanical stimuli is a crucial factor for maintaining cell homeostasis. The interaction between extracellular matrix and mechanical stress plays a significant role in organ-izing the cytoskeleton and aligning cells. Tools that apply mechanical forces to cells and tissues, as well as those capable of measuring the mechanical properties of biological cells, have greatly contributed to our understanding of fundamental mechanobiology. These tools have been exten-sively employed to unveil the substantial influence of mechanical cues on the development and progression of various diseases. In this report, we present an economical and high-performance uniaxial cell stretching device. This paper reports the detailed operation concept of the device, ex-perimental design, and characterization. The device was tested with MDA-MB-231 breast cancer cells. Experimental results agree well with previously documented morphological changes re-sulting from stretching forces on cancer cells. Remarkably, our new device demonstrates compa-rable cellular changes within a 30-minute compared to the previous 2-hour stretching duration. Moreover, the device design incorporates an open-source software interface, facilitating conven-ient parameter adjustments such as strain, stretching speed, frequency, and duration. Its versatil-ity enables seamless integration with various optical microscopes, thereby yielding novel insights into the realm of mechanobiology.

We investigated new anodic coloring materials that are used as ion storage layers in complementary energy storage electrochromic devices (ESECDs) to enhance their electrochromic storage performance. In this study, we fabricated counter electrodes (ion storage layers) using IrO2 doping NiO (Ir: NiO) film through cathodic arc plasma (CAP) with varying surface charge capacities. We investigated the influence of MoO3-doped WO3 (Mo: WO3) film by various Ar/O2 gas flow ratios (1/4, 1/5, and 1/6). The ESECDs used in the demonstration were 10×10 cm2 in size. They achieved optical transmittance modulation of Ir: NiO- ESECDs (glass/ITO/ Mo: WO3/gel-polymer electrolytes/ Ir: NiO /ITO/glass), ΔT=53.3% (from Tbleaching (66.6%) to Tcoloration (13.1%)). The ESECDs had a quick coloration time of 3.58 seconds, a rapid bleaching time of 1.24 seconds, and high cycling durability. It remained at 45% transmittance modulation even after 3000 cycles. New anodic materials can provide an alternative to traditional active materials for bi-functional electrochromic batteries.

This paper describes the design and development of an active device that was applied to shoulder rotation rehabilitation. It implements a force control in a similar way to the haptic devices that reflect a force on the user’s hand according to the rehabilitation parameters. This device was tested with patients, combining clinician manipulation and programmed exercises. The results were excellent, given that the range of movement of the shoulder increased in most of the pa-tients. The results of the Usability Scale questionnaire were also promising.

Ultrasound is a well-known tool to produce thermal and non-thermal effects on cells and tissues. These effects require a correct application of ultrasound in terms of localization and acoustic energy delivered. This article describes a new device that combines ultrasound and Dry Needling treatments. The ultrasound transducer can rotate in 3D space mechanically to align itself in the direction of the needle. The transducer electronically focuses the acoustic pressure automatically on the needle tip and its surroundings. A computer, using graphical interface software, controls the angulation of the array and the focus position.

In this paper, we investigate the relationship people have with their smart devices. We use the concept of agency to capture aspects of users’ sense of mastery as they relate to their device. This study gives preliminary evidence of the existence of two independent dimensions of agency for modeling the interaction between humans and smart devices: (i) user agency and (ii) device agency. These constructs emerged from an exploratory factorial analysis conducted on a survey data collected from 587 participants. In addition, we investigate the correlation between user agency and device agency with background variables of the respondents. Finally, we argue that mapping the users’ dynamics with their device into user agency and device agency fosters a better understanding of the needs of the users and helps in designing interfaces tailored for the specific capabilities and expectations of the users.

The purpose of this article is to present an IoT architecture implemented in an intelligent environment, focusing on the optimization of initial conditions and device management. A general control system was developed using an open-source platform, integrating aWi-Fi network and YAML coding to enable communication and control of the IoT architecture devices. The implementation includes actuators, sensors, and control devices that, through a graphical interface, allow the visualization of the historical record of activities and real-time measurements of connected devices. The design includes specific mechanisms and the analysis of materials through tensile tests on specimens, following the ASTM E8 standard, and deformation test simulations, in which PLA demonstrated better performance compared to materials like ABS and resin. The significance of the implemented IoT system lies in an energy saving of 58% compared to conventional structures. Additionally, the study of response times for network connections showed that using an Ethernet cable resulted in a response time of 1.21 seconds, representing a reduction of 1.65 seconds compared to the second lowest value obtained.

This research, which focuses on wave energy generating technology, suggests a brand-new oscillating float-type wave energy conversion system that is appropriate for the offshore wave environment. To accurately model the device, a three-dimensional viscous numerical pool is created based on STAR-CCM+. The array-type power generation device is numerically simulated using theoretical analysis and numerical simulation, and the wave energy power generation device is arranged as double floats in the front and rear rows, representing triangular array type and rectangular array type, respectively. The triangular array type is a superior layout and can make greater use of marine resources, according to this paper's analysis of the hydrodynamic and power generation impacts of the three array types. The findings are meant to serve as a guide for engineering practice.

The role of circulating plasma cells (CPCs) and circulating leukemic cells (CLCs) as biomarkers for several blood cancers, such as multiple myeloma and leukemia, respectively, have recently been reported. These markers can be attractive due to the minimally invasive nature of their acquisition through a blood draw (i.e., liquid biopsy) negating the need for painful bone marrow biopsies. CPCs or CLCs can be used for cellular/molecular analyses, such as immunophenotyping or fluorescence in situ hybridization (FISH). FISH, which is typically carried out on slides involving complex workflows, becomes problematic when operating on CLCs or CPCs due to their relatively modest numbers. Here, we present a microfluidic device for characterizing CPCs and CLCs enriched from peripheral blood using immunofluorescence or FISH. The microfluidic possessed an array of cross-channels (2-4 µm in depth and width) that interconnected a series of input and output fluidic channels. Placing a cover plate over the device formed microtraps, the size of which was defined by the width and depth of the cross-channels. This microfluidic chip allowed for automating immunofluorescence and FISH requiring the use of small volumes of reagents, such as antibodies and probes, as compared to slide-based immunophenotyping and FISH. In addition, the device could secure FISH results in <4 h compared to 2-3 d for conventional FISH.

A new circuit model of the self-powered device for heart rate measurement is presented in this paper. This device consists of piezoelectric energy harvester (PEH), power management circuit (PMC) with energy storage, microcontroller, Photoplethysmography (PPG) sensor, and Wi-Fi module. The PEH is placed under the insole to harvest the pressure energy from human foot-step to generate ac power. In our model, a PEH is represented by sine voltage source, where its parameters were taken from experiments with 20 volunteers. The PMC is simplified by a switch with gain δ placed in series with the main circuit. The model of the main circuit is RC elements in parallel, where C is the capacitance of the storage device, and R is the equivalent parallel resistance of the microcontroller, PPG sensor, and Wi-Fi modules, respectively. The value of R depends on the power and current absorbed by those modules during sleep, deep sleep, sense, and transmit modes which collected from the datasheet. Finally, the proposed circuit model of the self-powered device was built and simulated in SPICE. The simulation results were compared with the laboratory experiment using commercial devices. Based on the results, the proposed model had small gaps compared to the real self-powered devices in terms of average current, voltage, power and efficiency.

MEMS (Micro-electromechanical Systems) becomes important increasingly due to the smarter and smaller fuze used in OICW (Objective Individual Combat Weapon). MEMS Safety and Arming (S&A) device is employed in different platforms and regions for small caliber projectile. Therefore, it is necessary to make a parametric study of the MEMS S&A device in different apply environments and explore the main sensitive factors of the MEMS S&A device to provide reference for designs. In this paper, based on the MEMS S&A device designed by our term, theory and finite element models are established, and the centrifugal insurance mechanism of the MEMS S&A device is parametric studied under the different speeds, temperature and thickness of the model by nonlinear dynamic method. By comparing the experimental and predicted results, the established FEM model is verified, and the conclusion is that the temperature and the centrifugal force are the main sensitive factors in the centrifugal insurance mechanism. In summary, we can suggest that the application environment, which the MEMS S&A device is suitable for, is the temperature equal to or slightly greater than normal temperature and the rotating speed higher than35000r/min of small caliber projectile.

Empirically based modeling is an essential aspect of design for a wave energy converter. These models are used in structural, mechanical and control design processes, as well as for performance prediction. The design of experiments and methods used to produce models from collected data have a strong impact on the quality of the model. This study considers the system identification and model validation process based on data collected from a wave tank test of a model-scale wave energy converter. Experimental design and data processing techniques based on general system identification procedures are discussed and compared with the practices often followed for wave tank testing. The general system identification processes are shown to have a number of advantages. The experimental data is then used to produce multiple models for the dynamics of the device. These models are validated and their performance is compared against one and other. While most models of wave energy converters use a formulation with wave elevation as an input, this study shows that a model using a hull pressure sensor to incorporate the wave excitation phenomenon has better accuracy.

Sustainable urban drainage systems (SuDS) such as swales are designed to collect, store and infiltrate a large amount of surface runoff water during heavy rainfall. Stormwater is known to transport pollutants, such as particle-bound Potential Toxic Elements (PTE), which are known to often accumulate in the topsoil. A portable XRF instrument (pXRF) is used to provide in situ spatial characterization of soil pollutants, specifically lead (Pb), zink (Zn) and copper (Cu). The method uses pXRF measurements of PTE along profiles with set intervals (1 meter) to cover the swale with cross-sections, across the inlet, the deepest point and the outlet. Soil samples are collected, and the In-Situ measurements are verified by the results from laboratory analyses. Stormwater is here shown to be the transporting media for the pollutants, so it is of importance to investigate areas most prone to flooding and infiltration. This quick scan method is time and cost-efficient, easy to execute and the results are comparable to any known (inter)national threshold criteria for polluted soils. The results are of great importance for all stakeholders in cities that are involved in climate adaptation and implementing green infrastructure in urban areas. However, too little is still known about the long-term functioning of the soil-based SuDS facilities.

In order to meet the military requirements of the fuze, such as precision strike, efficient mutilates ability and low collateral damages, the microminiaturization is an inevitable trend of secure system. Based on the silicon-based MEMS S&A device designed by our term, the design principles of each module and fabrication process are introduced. The average fracture strength and Young's modulus of the silicon are 726 MPa and 175 GPa from the tensile test, respectively. From Hopkinson impact experiment, we can get the threshold-value judging mechanism being safety under the impact overload of 20526 g, and this value is much more than the standard of the drop overload 12000g; the arming value under the centrifugal overload obtained from theory, simulation and experiment is at the range of 28200 g and 32000 g, it shows that the threshold-value judging mechanism can be arming compared with the value 35951g of design principle. Therefore, the threshold-value judging mechanism can meet the design requirements of overload. Furthermore, the relationship of fracture threshold-values obtained by different theories is found out through parametric design method, as shown in Figure 14, it provides the theory evidence to the follow parametric design.

Electroluminescence (EL) is an innovative technology in the lighting area. The EL device's main structure consists of a phosphor layer sandwiched by two electrodes. In this work, several alternating current EL devices have been developed by applying a set of sequential layers with combinations of in-house prepared inks and commercially available ink as a phosphor layer. A flexible polyester textile substrate was functionalized with inks by spray coating technique, after knife-coated an interfacial layer directly on the surface. A thorough study was carried out on the phosphor layer composition to optimize the EL device performance, more precisely the illuminance intensity and the illuminance homogeneity. The developed phosphor layer was composed of zinc sulphide doped with copper (between 30.0 to 38.1 wt%) and diluted by using a diluent at different ratios (28.0 to 35.5 wt%). The best peak illuminance intensity of 61 lux was obtained when the phosphor ink presented 35.4% ZnS:Cu and was diluted with 33.0% diluent. The aim of this study to determine the best formulation of the phosphor layer, which can be highly promising for further developments of EL devices, taking in account different applications in market.

Fractional calculus is defined by expanded integer order integration and differentiation. In this paper, multiple mathematical models of a nonlinear dual tank device are precisely formulated by fractional calculus. Using the accurate model, multivariable Fractional-Order Controller is designed for the nonlinear device. The merits of the fractional-order design include: 1) Control of multivariable nonlinearities, 2) Compensation of uncertainties, 3) Elimination of coupling effects. Simulations and experiments are conducted to verify the precision of the fractional order models and the effectiveness of the multivariable fractional-order control design.

In recent years, since the propagation channel characteristics have been effectively used for applications such as motion sensing, position detection, etc. A great deal of attention is attracted to channel sounding methods easy to utilize using low-cost devices. This paper presents a device-free indoor location estimation method using spatio-temporal features of radio propagation channels using the 2.4-GHz band 3-by-3 MIMO channel sounder developed using commodity wireless LANs. The measurement results demonstrated a reasonable performance of the proposed method with small number of antennas.

In this paper a novel type of a highly sensitive gas sensor device based on the surface photovoltage effect is described. The developed surface photovoltage gas sensor is based on a reverse Kelvin probe approach. As the active gas sensing electrode the porous ZnO nanostructured thin films are used deposited by the direct current (DC) reactive magnetron sputtering method exhibiting the nanocoral surface morphology combined with an evident surface nonstoichiometry related to the unintentional surface carbon and water vapor contaminations. Among others, the demonstrated SPV gas sensor device exhibits a high sensitivity of 1 ppm to NO₂ with a signal to noise ratio of about 50 and a fast response time of several seconds under the room temperature conditions.

This article reports a novel and efficient method to synthesize graphene by thermal decomposition process. In this method, silicon carbide (SiC) thin films grown on Si(100) wafers with an AlN buffer layer were used as substrates. A CO₂ laser beam heating without vacuum or controlled atmosphere was applied for SiC thermal decomposition. The physical, chemical, morphological, and electrical properties of the laser-produced graphene were investigated for different laser energy densities. The results demonstrate that graphene was produced in form of small islands with quality, density and properties depending on the applied laser energy density. Furthermore, the produced graphene exhibits a sheet resistance characteristic similar to graphene grown on mono-crystalline SiC wafer, which indicates its potential for electronic device applications.

The application of Virtual Reality in a driving simulation is not novel, yet little is known about the use of this technology by senior populations. The effects of age, sex, control device (joystick or handlebar), and task type on wayfinding proficiency using a virtual reality (VR) driving simulation were explored. The driving experimental model involved 96 randomly recruited participants, including 48 young people and 48 seniors (split evenly by gender in each group). The experimental results and statistical analyses indicate that in a VR driving scenario task type significantly affected VR driving performance. Navigational scores were significantly higher for the straight (easy) task than for the curved (difficult) task. The aging effect was the main reason for significant and interacting effects of sex and control device. It was found that interactions between age and sex difference indicated that the young group exhibited better wayfinding performance than the senior group, and in the young group males had better performance than females. Similarly, interactions between age and control device indicated that the handlebar control device type resulted in better performance than the joystick device in the young group, but no difference was found in the senior group due to age or learning effects. Findings provide an understanding of the evaluation of the interface designs of navigational support systems, taking into consideration any effects of age, sex, control device, and task type within three-dimensional VR games and driving systems. With a VR driving simulator, seniors can test drive inaccessible products, such as electric bicycles or cars, using a computer at home.

An increasing number of aircraft is equipped with wing tip devices, which either are installed by the aircraft manufacturer at the production line or are retrofitted after the delivery of the aircraft to its operator. Installation of wing tip devices has not been a popular choice for regional turboprop aircraft and the novelty of the current study is to investigate the feasibility of retrofitting the British Aerospace (BAe) Jetstream 31 with an appropriate wing tip device (or winglet) to increase its cruise range performance, taking also into account the aerodynamic and structural impact of the implementation. To the best of the knowledge of the authors, no previous study exists which has attempted to assess the winglet retrofit of an existing aircraft type of similar size and operating profile. The optimal winglet design achieved a 2.38% increase of the maximum range by reducing the total drag by 1.19% at a mass penalty of 3.25%, as compared with the baseline aircraft configuration. Other designs were found to be more effective in reducing the total drag, but the structural reinforcement required for their implementation outweighed the achieved performance improvements. Since successful winglet retrofit programs for typical short to medium range narrow body aircraft report even more than 3% of block fuel improvements, undertaking the project of installing an optimal winglet design to the BAe Jetstream 31, should also consider a Direct Operating Cost (DOC) assessment on top of the aerodynamic and structural aspects of the retrofit.

In this work, an algorithm was developed to measure the respiration rate for an embedded device that can be used by a field robot for relief operation. With this algorithm, the rate measurement was calculated based on direct influences of respiratory-induced intensity variation (RIIV) on blood flow in cardiovascular pathways. For that, a photoplethysmogram (PPG) sensor was used to determine changes in heartbeat frequencies. The PPG sensor readings were filtered using an Information Filter and a Fast Fourier transform (FFT) to determine the state of RIIV. With a relatively light initialization, the information filter can estimate unknown variables based on a series of measurements containing noise and other inaccuraties. Therefore, this filter is suitable for application on an embedded device. For faster calculation time in the implementation, the FFT analysis was calculated only for a major peak in the frequency domain. Test and measurement of respiration rate was conducted based on the device algorithm and spirometer. Heartbeat measurement was also evaluated by comparing the heartbeat data of the PPG sensor and the medical tool kit. Based on the test, the implemented algorithm can measure respiration rate with about 80% accuracy compared with the spirometer.

Wearable exoskeleton solutions for upper limb rehabilitation or assistance, particularly for the hand area, have become increasingly attractive to researchers, proving to be effective over time in treating hand movement impairments following various neurological diseases. In the present work, the development of a wearable exoskeleton-type device for active hand rehabilitation has been addressed, based on fluid actuators made of elastomeric material and on myoelectric control by capturing myoelectric signals from the forearm area. The flexion movement of the fingers (phalanges) is actively assisted by pneumatic actuation of the built-in actuators and the extension movement is assisted by a depressurization control of the actuator. The device has been designed to be as easy to use as possible, light in weight, and to provide a high degree of comfort when used by the patient for rehabilitation training or daily life activities (ADL), which can be performed in the comfort of one's own home.

This work aims to study and analyze a hybrid power system for electric vehicles consisting of a dual low and high-rate lithium battery block and a fuel cell. In this configuration, the high-rate lithium battery powers the electric vehicle in high power demand processes like acceleration mode or on an uphill road; the low-rate battery operates at a low output power range, servicing the auxiliary systems and low power loads and the fuel cell supplies energy at intermediate power demand conditions, normal driving mode, constant velocity, or flat and downhill terrain. The dual power system improves global efficiency since every power unit operates optimally depending on driving conditions. Power sharing optimizes the lithium battery performance and fuel cell capacity, minimizing the size and weight of each energy system and enlarging the driving range. A comparative study between different lithium battery configurations and fuel cell shows an efficiency improvement of 31.4% for the hybrid dual battery block and fuel cell operating in low, high, and intermediate output power ranges, respectively. The study bases on a simulation process recreating current driving conditions for electric cars in urban, peripheral, and intercity routes. An alternative solution consisting of a hybrid system, fuel cell and a high rate lithium battery produces a 29 % power gain.

We present a custom platform that integrates data from several sensors measuring synchronously different variables of the beehive and wirelessly transmits all measurements to a cloud server. There is a rich literature on beehive monitoring. The choice of our work is not to use ready platforms such as Arduino and Raspberry Pi and to present a low cost and power solution for long term monitoring. We integrate sensors that are not limited to the typical toolbox of beehive monitoring such as gas, vibrations and bee counters. The synchronous sampling of all sensors every 5 minutes allows us to form a multivariable timeseries that serves two-ways: a) it provides immediate alerting in case a measurement exceeds predefined boundaries that are known to characterize a healthy beehive, and b) based on historical data predict future levels that are correlated with hive’s health. Finally, we demonstrate the benefit of using additional regressors in the prediction of the variables of interest. The database, the code and a video of the vibrational activity of two months are made open to the interested readers.

Background: Continuous subcutaneous apomorphine infusion (CSAI), levodopa-carbidopa intestinal gel infusion (LCIG), and deep brain stimulation of the subthalamic nucleus (STN-DBS) have markedly changed the treatment landscape of advanced Parkinson’s disease (aPD). Despite a similar outcome of all device-aided therapies (DATs), some patients switch or combine DATs. The aim of this retrospective study was to explore the frequency and reasons for switching between or combining DATs in two movement disorders centres in Slovenia and Israel. Methods: We collected and analysed demographic and clinical data from aPD patients who switched between or combined DATs. Motor and non-motor reasons and their frequency for switching/combining were examined, as was the effect of DAT using the Global Improvement subscale of the Clinical Global Impression Scale. Non-parametric tests were used to analyse the data. Results: Of 505 aPD patients treated with DATs at both centres between January 2009 and June 2021, we identified in total 30 patients (6%), who either switched DAT (N=24: 7 LCIG-to-STN-DBS, 1 LCIG-to-CSAI, 5 CSAI-to STN-DBS, 8 CSAI-to-LCIG, 1 STN-DBS-to-LCIG, 1 LCIG-to-CSAI-to-STN-DBS, and 1 STN-DBS-to-CSAI-to-LCIG) or combined DATs (N=6: 5 STN-DBS+LCIG and 1 STN-DBS+CSAI-to-STN-DBS+LCIG). In most of these patients, inadequate control of motor symptoms was the main reason for switching or combining DATs, but non-motor reasons (related to the disease and/or DAT) were also identified. Conclusions: Switching between and combining DATs is uncommon, but in some patients brings substantial clinical improvement and should be considered in those who have either inadequate symptom control on DAT treatment or have developed DAT related complications.

In order to solve the problem of measuring the distance and position between the flanges of two pipelines on the seabed, a measuring device for pulling rope in seawater was designed. Aiming at the sealing problem of the key equipment that is the rotating shaft of the rope winch, this paper used the principle of the magnetic coupling to transfer the driving moment, and adopted the method of converting the dynamic seal into the static seal structure to realize the reliable sealing of the motor. Through the experiment of measuring two pipelines with underwater rope pulling device, it was verified that the measuring accuracy of the device meets the design requirements, and the feasibility of the application of magnetic coupling technology in winch is also verified.

Background: Effectiveness of Anastrozole and levonorgestrel-releasing intrauterine device (LNG-IUD, Mirena®) in the treatment of endometriosis. Methods: Randomized clinical trial. Elegibility criteria: Endometriomas >3×4 cm, CA-125>35 U/mL and symptoms suggestive of endometriosis. Thirty-one women were randomized to anastrozole+Mirena®+Conservative Surgery(CS) (n=8), anastrozole+Mirena®+transvaginal ultrasound-guided puncture-aspiration(TUGPA) (n=7), Mirena®+CS (n=9), or Mirena®+TUGPA (n=7). Interventions: Anastrozole 1 mg/day and/or only Mirena® for 6 months. CS or TUGPA one month after starting medical treatment. Results: A significant improvement in symptoms during the treatment (difference of 43%, 95% CI 29.9-56.2) occurred, which was maintained at 1 and 2 years. It was more significant in patients treated with anastrozole. For CA-125, the most significant decrease was observed without anastrozole. After CS for endometriosis, a reduction of findings of endometriomas and long-term recurrences occurred, with or without anastrozole, although anastrozole seems to delay recurrences. At 4,2±1,7 years, 88% of the patients who underwent CS were asymptomatic, compared to only 21% if TUGPA was performed, with or without anastrozole (p=0.019). Conclusion: Dosing anastrozole for 6 months, starting one month before CS of endometriosis, reduces more significantly the painful symptoms and delays recurrences, but has no other significant advantages over the single insertion of LNG-IUD (Mirena®) during the same time.

We introduce a device for automatic detection and reporting of crawling insects in urban environments. It is a monitoring device for urban pests that complies with the context of smart homes, smart cities and is compatible with the emerging discipline of the Internet of Things (IoT). We believe it can find its place to every room of a hotel, hospital, military camp and residence. This box-shaped device attracts targeted insect pests, senses the entering insect and takes automatically a picture of the internal space of the box. The picture is communicated through the Wi-Fi commonly found in such establishments to an authorized person/stakeholder receiving the picture to take proper action. The e-trap includes strong attractants (pheromone and/or food) to increase capture efficiency. The insect is trapped on the sticky floor of the device. The device carries the necessary optoelectronic sensors to guard all entrances of the trap. As the insect enters it interrupts the infrared light source. This triggers a detection event; a picture is taken, and a time-stamp is set before reporting the event through the Wi-Fi. The device can be integrated seamlessly in urban environments and operates unobtrusively to human activities. We report results on various insect pests and depending on the insect species, can reach a detection accuracy ranging from 96-99%.

The aim of this work is to evaluate the impact of proposed modifications to conventional capturing and discharging effluents devices in Subsurface Flow Wetland (SSFW) systems. Main modifications proposed consist on extending the influence of the capture and discharge device in such a way that the SSFW width and height are fully covered. Additionally an SSFW prototype was built as pilot including the proposed modifications and the impact of the innovative device is measured based on the efficiency of the Chemical Oxygen Demand (COD) removal as compared to a traditionally built SSFW. The results show that for the innovative device, the COD removal was 10% higher than for the conventional device.

The paper is concerned with the concept of elementary observations (EO). EOs are experimental answers to the question whether a matter-instrument interaction had taken place at the micro-scale of quantum phenomena. Focusing on the specific case of photon detection, we show that during their lifetimes EOs proceed through the four phases of initiation, detection, erasure and reset. Once generated, the observational value of EOs can be measured in units of the Planck quantum of physical action h=4.136×10^(-15) eVs. Once terminated, each unit of entropy of size k_B=8.617×10^(-5) eV⁄K, which had been created in the instrument during the observational phase, needs to be removed from the instrument to ready it for a new round of photon detection. This withdrawal of entropy takes place at an energetic cost of at least two units of the Landauer minimum energy bound of E_La=ln⁡〖(2) k_B T_D 〗 for each unit of entropy of size k_B.

Cardiovascular diseases (CVDs) and chronic kidney disease (CKD) are frequently interconnected and their association leads to an exponential increase in the risk of both fatal and non-fatal events. In addition, the burden of arrhythmias in CKD patients is increased. On the other hand, the presence of CKD is an important factor that influences the decision to pursue cardiac device therapy. Data on CKD patients with device therapy is scarce and mostly derives from observational studies and case reports. Cardiac resynchronization therapy (CRT) is associated with decreased mortality, reduced heart failure symptoms and improved renal function in early stages of CKD. Implantable cardioverter defibrillators (ICDs) are associated with a significant reduction in the mortality of CKD patients only for the secondary prevention of sudden cardiac death. Cardiac resynchronization therapy defibrillator (CRT-D) is preferred in patients that meet the established criteria. The need for cardiac pacing is 3-fold higher in dialysis patients. CKD is an independent risk factor for infections associated with cardiac devices.

THz radiation has assumed a great importance thanks to the efforts in the development of technological tools used in this versatile band of the electromagnetic spectrum. Here we propose a reflecting bi-mirror axicon-like device with wavelength-independent long focusing performances in the THz band, by exploiting the high thermo-mechanical deformation of the elastomer polydimethylsiloxane (PDMS). This deformation permits to achieve significant optical path modulations in the THz band and effective focusing. The surface of a PDMS layer is covered with a gold thin film, acting as heater thanks to its absorption for wavelengths below ~500 nm . An invariance property of the Fresnel integral has been exploited to verify experimentally the THz performances of the device with an ordinary visible laser source, finding excellent agreement with the theoretical predictions at 1 and 3 THz. The same property allowed also to verify experimentally that the axicon focus has a longitudinal extension much greater than that one exhibited by a benchmark cylindrical mirror with the same optical power. The axicon is thermo-mechanically stable up to a heating power of 270 mW, although it might be potentially exploited at higher powers with a minor degradation of the optical performances.